[Federal Register Volume 80, Number 51 (Tuesday, March 17, 2015)]
[Proposed Rules]
[Pages 13791-13794]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2015-05947]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF ENERGY

10 CFR Part 430

[Docket No. EERE-2011-BT-NOA-0013]


Energy Conservation Program: Data Collection and Comparison With 
Forecasted Unit Sales of Five Lamp Types

AGENCY: Office of Energy Efficiency and Renewable Energy, Department of 
Energy.

ACTION: Notice of data availability.

-----------------------------------------------------------------------

SUMMARY: The U.S. Department of Energy (DOE) is informing the public of 
its collection of shipment data and creation of spreadsheet models to

[[Page 13792]]

provide comparisons between actual and benchmark estimate unit sales of 
five lamp types (i.e., rough service lamps, vibration service lamps, 3-
way incandescent lamps, 2,601-3,300 lumen general service incandescent 
lamps, and shatter-resistant lamps) that are currently exempt from 
energy conservation standards. As the actual sales do not exceed the 
forecasted estimate by 100 percent for any lamp type (i.e., the 
threshold triggering a rulemaking for an energy conservation standard), 
DOE has determined that no regulatory action is necessary at this time. 
However, DOE will continue to track sales data for these exempted 
lamps. Relating to this activity, DOE has prepared, and is making 
available on its Web site, a spreadsheet showing the comparisons of 
anticipated versus actual sales, as well as the model used to generate 
the original sales estimates. The spreadsheet is available online at: 
http://www1.eere.energy.gov/buildings/appliance_standards/product.aspx/productid/63.

DATES: As of March 17, 2015, DOE has determined that no regulatory 
action is necessary at this time.

FOR FURTHER INFORMATION CONTACT:
    Ms. Lucy deButts, U.S. Department of Energy, Office of Energy 
Efficiency and Renewable Energy, Building Technologies, EE-2J, 1000 
Independence Avenue SW., Washington, DC 20585-0121. Telephone: (202) 
287-1604. Email: [email protected].
    Mr. Peter Cochran, U.S. Department of Energy, Office of the General 
Counsel, GC-33, 1000 Independence Avenue SW., Washington, DC 20585-
0121. Telephone: (202) 586-9496. Email: [email protected].

SUPPLEMENTARY INFORMATION: 

Table of Contents

I. Background
II. Definitions
    A. Rough Service Lamps
    B. Vibration Service Lamps
    C. Three-Way Incandescent Lamps
    D. 2,601-3,300 Lumen General Service Incandescent Lamps
    E. Shatter-Resistant Lamps
III. Comparison Methodology
IV. Comparison Results
    A. Rough Service Lamps
    B. Vibration Service Lamps
    C. Three-Way Incandescent Lamps
    D. 2,601-3,300 Lumen General Service Incandescent Lamps
    E. Shatter-Resistant Lamps
V. Conclusion

I. Background

    The Energy Independence and Security Act of 2007 (EISA 2007; Pub. 
L. 110-140) was enacted on December 19, 2007. Among the requirements of 
subtitle B (Lighting Energy Efficiency) of title III of EISA 2007 were 
provisions directing DOE to collect, analyze, and monitor unit sales of 
five lamp types (i.e., rough service lamps, vibration service lamps, 3-
way incandescent lamps, 2,601-3,300 lumen general service incandescent 
lamps, and shatter-resistant lamps). In relevant part, section 
321(a)(3)(B) of EISA 2007 amended section 325(l) of the Energy Policy 
and Conservation Act of 1975 (EPCA) by adding paragraph (4)(B), which 
generally directs DOE, in consultation with the National Electrical 
Manufacturers Association (NEMA), to: (1) Collect unit sales data for 
each of the five lamp types for calendar years 1990 through 2006 in 
order to determine the historical growth rate for each lamp type; and 
(2) construct a model for each of the five lamp types based on 
coincident economic indicators that closely match the historical annual 
growth rates of each lamp type to provide a neutral comparison 
benchmark estimate of future unit sales. (42 U.S.C. 6295(l)(4)(B)) 
Section 321(a)(3)(B) of EISA 2007 also amends section 325(l) of EPCA by 
adding paragraph (4)(C), which, in relevant part, directs DOE to 
collect unit sales data for calendar years 2010 through 2025, in 
consultation with NEMA, for each of the five lamp types. DOE must then: 
(1) Compare the actual lamp sales in that year with the benchmark 
estimate; (2) determine if the unit sales projection has been exceeded; 
and (3) issue the findings within 90 days of the end of the analyzed 
calendar year. (42 U.S.C. 6295(l)(4)(C))
    On December 18, 2008, DOE issued a notice of data availability 
(NODA) for the Report on Data Collection and Estimated Future Unit 
Sales of Five Lamp Types (hereafter the ``2008 analysis''), which was 
published in the Federal Register on December 24, 2008. 73 FR 79072. 
The 2008 analysis presented the 1990 through 2006 shipment data 
collected in consultation with NEMA, the spreadsheet model DOE 
constructed for each lamp type, and the benchmark unit sales estimates 
for 2010 through 2025. On April 4, 2011, DOE published a NODA in the 
Federal Register announcing the availability of updated spreadsheet 
models presenting the benchmark estimates from the 2008 analysis and 
the collected sales data from 2010 for the first annual comparison. 76 
FR 18425. Similarly, DOE published NODAs in the Federal Register in the 
following three years announcing the updated spreadsheet models and 
sales data for the annual comparisons. 77 FR 16183 (March 20, 2012); 78 
FR 15891 (March 13, 2013); 79 FR 15058 (March 18, 2014). This NODA 
presents the fifth annual comparison; specifically, section IV of this 
report compares the actual unit sales against benchmark unit sales 
estimates for 2014.\1\
---------------------------------------------------------------------------

    \1\ The notices and related documents for the 2008 analysis and 
successive annual comparisons, including this NODA, are available 
through the DOE Web site at: http://www1.eere.energy.gov/buildings/appliance_standards/product.aspx/productid/63.
---------------------------------------------------------------------------

    EISA 2007 also amends section 325(l) of EPCA by adding paragraphs 
(4)(D) through (4)(H), which state that if DOE finds that the unit 
sales for a given lamp type in any year between 2010 and 2025 exceed 
the benchmark estimate of unit sales by at least 100 percent (i.e., 
more than double the anticipated sales), then DOE must take regulatory 
action to establish an energy conservation standard for such lamps. (42 
U.S.C. 6295(l)(4)(D) through (H)) For 2,601-3,300 lumen general service 
incandescent lamps, DOE must adopt a statutorily prescribed energy 
conservation standard. For the other four types of lamps, the statute 
requires DOE to initiate an accelerated rulemaking to establish energy 
conservation standards. If the Secretary does not complete the 
accelerated rulemakings within one year of the end of the previous 
calendar year, there is a ``backstop requirement'' for each lamp type, 
which would establish energy conservation standard levels and related 
requirements by statute. Id.
    As in the 2008 analysis and previous comparisons, DOE uses 
manufacturer shipments as a surrogate for unit sales in this NODA 
because manufacturer shipment data are tracked and aggregated by the 
trade organization, NEMA. DOE believes that annual shipments track 
closely with actual unit sales of these five lamp types, as DOE 
presumes that retailer inventories remain constant from year to year. 
DOE believes this is a reasonable assumption because the markets for 
these five lamp types have existed for many years, thereby enabling 
manufacturers and retailers to establish appropriate inventory levels 
that reflect market demand. In addition, increasing unit sales must 
eventually result in increasing manufacturer shipments. This is the 
same methodology presented in DOE's 2008 analysis and subsequent annual 
comparisons, and the Department did not receive any comments 
challenging this assumption or the general approach.

[[Page 13793]]

II. Definitions

A. Rough Service Lamps

    Section 321(a)(1)(B) of EISA 2007 amended section 321(30) of EPCA 
by adding the definition of a ``rough service lamp.'' The statutory 
definition reads as follows: ``The term `rough service lamp' means a 
lamp that--(i) has a minimum of 5 supports with filament configurations 
that are C-7A, C-11, C-17, and C-22 as listed in Figure 6-12 of the 9th 
edition of the IESNA [Illuminating Engineering Society of North 
America] Lighting handbook, or similar configurations where lead wires 
are not counted as supports; and (ii) is designated and marketed 
specifically for `rough service' applications, with--(I) the 
designation appearing on the lamp packaging; and (II) marketing 
materials that identify the lamp as being for rough service.'' (42 
U.S.C. 6291(30)(X))
    As noted above, rough service incandescent lamps must have a 
minimum of five filament support wires (not counting the two connecting 
leads at the beginning and end of the filament), and must be designated 
and marketed for ``rough service'' applications. This type of 
incandescent lamp is typically used in applications where the lamp 
would be subject to mechanical shock or vibration while it is 
operating. Standard incandescent lamps have only two support wires 
(which also serve as conductors), one at each end of the filament coil. 
When operating (i.e., when the tungsten filament is glowing so hot that 
it emits light), a standard incandescent lamp's filament is brittle, 
and rough service applications could cause it to break prematurely. To 
address this problem, lamp manufacturers developed lamp designs that 
incorporate additional support wires along the length of the filament 
to ensure that it has support not just at each end, but at several 
other points as well. The additional support protects the filament 
during operation and enables longer operating life for incandescent 
lamps in rough service applications. Typical applications for these 
rough service lamps might include commercial hallways and stairwells, 
gyms, storage areas, and security areas.

B. Vibration Service Lamps

    Section 321(a)(1)(B) of EISA 2007 amended section 321(30) of EPCA 
by adding the definition of a ``vibration service lamp.'' The statutory 
definition reads as follows: ``The term `vibration service lamp' means 
a lamp that--(i) has filament configurations that are C-5, C-7A, or C-
9, as listed in Figure 6-12 of the 9th Edition of the IESNA Lighting 
Handbook or similar configurations; (ii) has a maximum wattage of 60 
watts; (iii) is sold at retail in packages of 2 lamps or less; and (iv) 
is designated and marketed specifically for vibration service or 
vibration-resistant applications, with--(I) the designation appearing 
on the lamp packaging; and (II) marketing materials that identify the 
lamp as being vibration service only.'' (42 U.S.C. 6291(30)(AA))
    The statute mentions three examples of filament configurations for 
vibration service lamps in Figure 6-12 of the IESNA Lighting Handbook, 
one of which (i.e., C-7A) is also listed in the statutory definition of 
``rough service lamp.'' The definition of ``vibration service lamp'' 
requires that such lamps have a maximum wattage of 60 watts and be sold 
at a retail level in packages of two lamps or fewer. Similar to rough 
service lamps, vibration service lamps must be designated and marketed 
for vibration service or vibration-resistant applications. As the name 
suggests, this type of incandescent lamp is generally used in 
applications where the incandescent lamp would be subject to a 
continuous low level of vibration, such as in a ceiling fan light kit. 
In such applications, standard incandescent lamps without additional 
filament support wires may not achieve the full rated life, because the 
filament wire is brittle and would be subject to breakage at typical 
operating temperature. To address this problem, lamp manufacturers 
typically use a more malleable tungsten filament to avoid damage and 
short circuits between coils.

C. Three-Way Incandescent Lamps

    Section 321(a)(1)(B) of EISA 2007 amended section 321(30) of EPCA 
by adding the definition of a ``3-way incandescent lamp.'' The 
statutory definition reads as follows: ``The term `3-way incandescent 
lamp' includes an incandescent lamp that--(i) employs 2 filaments, 
operated separately and in combination, to provide 3 light levels; and 
(ii) is designated on the lamp packaging and marketing materials as 
being a 3-way incandescent lamp.'' (42 U.S.C. 6291(30)(Y))
    Three-way lamps are commonly found in wattage combinations such as 
50, 100, and 150 watts or 30, 70, and 100 watts. These lamps use two 
filaments (e.g., a 30-watt and a 70-watt filament) and can be operated 
separately or together to produce three different lumen outputs (e.g., 
305 lumens with one filament, 995 lumens with the other, or 1,300 
lumens using the filaments together). When used in three-way sockets, 
these lamps allow users to control the light level. Three-way 
incandescent lamps are typically used in residential multi-purpose 
areas, where consumers may adjust the light level to be appropriate for 
the task they are performing.

D. 2,601--3,300 Lumen General Service Incandescent Lamps

    The statute does not provide a definition of ``2,601-3,300 Lumen 
General Service Incandescent Lamps''; however, DOE is interpreting this 
term to be a general service incandescent lamp \2\ that emits light 
between 2,601 and 3,300 lumens. Lamps on the market that emit light 
within this lumen range are immediately recognizable because, as 
required by the Energy Policy Act of 1992, Public Law 102-486, all 
general service incandescent lamps must be labeled with lamp lumen 
output.\3\ These lamps are used in general service applications when 
high light output is needed.
---------------------------------------------------------------------------

    \2\ ``The term `general service incandescent lamp' means a 
standard incandescent or halogen type lamp that--(I) is intended for 
general service applications; (II) has a medium screw base; (III) 
has a lumen range of not less than 310 lumens and not more than 
2,600 lumens or, in the case of a modified spectrum lamp, not less 
than 232 lumens and not more than 1,950 lumens; and (IV) is capable 
of being operated at a voltage range at least partially within 110 
and 130 volts.'' (42 U.S.C. 6291(30)(D)(i)).
    \3\ The Federal Trade Commission issued the lamp labeling 
requirements in 1994 (see 59 FR 25176 (May 13, 1994)). Further 
amendments were made to the lamp labeling requirements in 2007 (see 
16 CFR 305.15(b); 72 FR 49948, 49971-72 (August 29, 2007)). The 
package must display the lamp's light output (in lumens), energy use 
(in watts), and lamp life (in hours).
---------------------------------------------------------------------------

E. Shatter-Resistant Lamps

    Section 321(a)(1)(B) of EISA 2007 amended section 321(30) of EPCA 
by adding the definition of a ``shatter-resistant lamp, shatter-proof 
lamp, or shatter-protected lamp.'' The statutory definition reads as 
follows: ``The terms `shatter-resistant lamp,' `shatter-proof lamp,' 
and `shatter-protected lamp' mean a lamp that--(i) has a coating or 
equivalent technology that is compliant with [National Sanitation 
Foundation/American National Standards Institute] NSF/ANSI 51 and is 
designed to contain the glass if the glass envelope of the lamp is 
broken; and (ii) is designated and marketed for the intended 
application, with--(I) the designation on the lamp packaging; and (II) 
marketing materials that identify the lamp as being shatter-resistant, 
shatter-proof, or shatter-protected.'' (42 U.S.C. 6291(30)(Z)) Although 
the definition provides three names commonly used to refer to these 
lamps, DOE simply refers to them collectively as ``shatter-resistant 
lamps.''
    Shatter-resistant lamps incorporate a special coating designed to 
prevent glass

[[Page 13794]]

shards from being dispersed if a lamp's glass envelope breaks. Shatter-
resistant lamps incorporate a coating compliant with industry standard 
NSF/ANSI 51,\4\ ``Food Equipment Materials,'' and are labeled and 
marketed as shatter-resistant, shatter-proof, or shatter-protected. 
Some types of the coatings can also protect the lamp from breakage in 
applications subject to heat and thermal shock that may occur from 
water, sleet, snow, soldering, or welding.
---------------------------------------------------------------------------

    \4\ NSF/ANSI 51 applies specifically to materials and coatings 
used in the manufacturing of equipment and objects destined for 
contact with foodstuffs.
---------------------------------------------------------------------------

III. Comparison Methodology

    In the 2008 analysis, DOE reviewed each of the five sets of 
shipment data that was collected in consultation with NEMA and applied 
two curve fits to generate unit sales estimates for the five lamp types 
after calendar year 2006. One curve fit applied a linear regression to 
the historical data and extended that line into the future. The other 
curve fit applied an exponential growth function to the shipment data 
and projected unit sales into the future. For this calculation, linear 
regression treats the year as a dependent variable and shipments as the 
independent variable. The linear regression curve fit is modeled by 
minimizing the differences among the data points and the best curve-fit 
linear line using the least squares function.\5\ The exponential curve 
fit is also a regression function and uses the same least squares 
function to find the best fit. For some data sets, an exponential curve 
provides a better characterization of the historical data, and, 
therefore, a better projection of the future data.
---------------------------------------------------------------------------

    \5\ The least squares function is an analytical tool that DOE 
uses to minimize the sum of the squared residual differences between 
the actual historical data points and the modeled value (i.e., the 
linear curve fit). In minimizing this value, the resulting curve fit 
will represent the best fit possible to the data provided.
---------------------------------------------------------------------------

    For 3-way incandescent lamps, 2,601-3,300 lumen general service 
incandescent lamps, and shatter-resistant lamps, DOE found that the 
linear regression and exponential growth curve fits produced nearly the 
same estimates of unit sales (i.e., the difference between the two 
forecasted values was less than 1 or 2 percent). However, for rough 
service and vibration service lamps, the linear regression curve fit 
projected lamp unit sales would decline to zero for both lamp types by 
2018. In contrast, the exponential growth curve fit projected a more 
gradual decline in unit sales, such that lamps would still be sold 
beyond 2018, and it was, therefore, considered the more realistic 
forecast. While DOE was satisfied that either the linear regression or 
exponential growth spreadsheet model generated a reasonable benchmark 
unit sales estimate for 3-way incandescent lamps, 2,601-3,300 lumen 
general service incandescent lamps, and shatter-resistant lamps, DOE 
selected the exponential growth curve fit for these lamp types for 
consistency with the selection made for rough service and vibration 
service lamps.\6\ DOE examines the benchmark unit sales estimates and 
actual sales for each of the five lamp types in the following section 
and also makes the comparisons available in a spreadsheet online: 
http://www1.eere.energy.gov/buildings/appliance_standards/product.aspx/productid/63.
---------------------------------------------------------------------------

    \6\ This selection is consistent with the previous annual 
comparisons. See DOE's 2008 forecast spreadsheet models of the lamp 
types for greater detail on the estimates.
---------------------------------------------------------------------------

IV. Comparison Results

A. Rough Service Lamps

    For rough service lamps, the exponential growth forecast projected 
the benchmark unit sales estimate for 2014 to be 5,224,000 units. The 
NEMA-provided shipment data reported shipments of 7,267,000 units in 
2014. As this finding exceeds the estimate by only 39.1 percent, DOE 
will continue to track rough service lamp sales data and will not 
initiate regulatory action for this lamp type at this time.

B. Vibration Service Lamps

    For vibration service lamps, the exponential growth forecast 
projected the benchmark unit sales estimate for 2014 to be 2,729,000 
units. The NEMA-provided shipment data reported shipments of 5,220,000 
units in 2014. As this finding exceeds the estimate by only 91.3 
percent, DOE will continue to track vibration service lamp sales data 
and will not initiate regulatory action for this lamp type at this 
time.

C. Three-Way Incandescent Lamps

    For 3-way incandescent lamps, the exponential growth forecast 
projected the benchmark unit sales estimate for 2014 to be 49,107,000 
units. The NEMA-provided shipment data reported shipments of 35,340,000 
units in 2014. As this finding is only 72.0 percent of the estimate, 
DOE will continue to track 3-way incandescent lamp sales data and will 
not initiate regulatory action for this lamp type at this time.

D. 2,601-3,300 Lumen General Service Incandescent Lamps

    For 2,601-3,300 lumen general service incandescent lamps, the 
exponential growth forecast projected the benchmark unit sales estimate 
for 2014 to be 34,110,000 units. The NEMA-provided shipment data 
reported shipments of 5,232,000 units in 2014. As this finding is 15.3 
percent of the estimate, DOE will continue to track 2,601-3,300 lumen 
general service incandescent lamp sales data and will not initiate 
regulatory action for this lamp type at this time.

E. Shatter-Resistant Lamps

    For shatter-resistant lamps, the exponential growth forecast 
projected the benchmark unit sales estimate for 2014 to be 1,671,000 
units. The NEMA-provided shipment data reported shipments of 1,042,000 
units in 2014. As this finding is only 62.4 percent of the estimate, 
DOE will continue to track shatter-resistant lamp sales data and will 
not initiate regulatory action for this lamp type at this time.

V. Conclusion

    None of the shipments for rough service lamps, vibration service 
lamps, 3-way incandescent lamps, 2,601-3,300 lumen general service 
incandescent lamps, or shatter-resistant lamps crossed the statutory 
threshold for a standard. DOE will continue to monitor these five 
currently exempted lamp types and will assess 2015 sales by March 31, 
2016, in order to determine whether an energy conservation standards 
rulemaking is required, consistent with 42 U.S.C. 6295(l)(4)(D) through 
(H).

    Issued in Washington, DC, on March 10, 2015.
Kathleen B. Hogan,
Deputy Assistant Secretary for Energy Efficiency, Energy Efficiency and 
Renewable Energy.
[FR Doc. 2015-05947 Filed 3-16-15; 8:45 am]
 BILLING CODE 6450-01-P