[Federal Register Volume 79, Number 240 (Monday, December 15, 2014)]
[Proposed Rules]
[Pages 74035-74037]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2014-29233]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2014-0922; Directorate Identifier 2014-NM-156-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain Airbus Model A319 and A320 series airplanes. This proposed AD 
was prompted by a report that fatigue cracking could appear at certain 
fastener locations in the longeron area below the emergency exit cut-
outs. This proposed AD is intended to complete certain mandated 
programs intended to support the airplane reaching its limit of 
validity (LOV) of the engineering data that support the established 
structural maintenance program. This proposed AD would require 
modification of eight fastener locations in the longeron area below the 
emergency exit cut-outs on the left-hand (LH) and right-hand (RH) 
sides. We are proposing this AD to detect and correct cracking at 
certain fastener locations in the longeron area below the emergency 
exit cut-outs, which could lead to failure of the fasteners and reduced 
structural integrity of the airplane.

DATES: We must receive comments on this proposed AD by January 29, 
2015.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Airbus, Airworthiness Office--EIAS, 1 Rond Point Maurice Bellonte, 
31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 
93 44 51; email [email protected]; Internet http://www.airbus.com. You may view this referenced service information at the 
FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. 
For information on the availability of this material at the FAA, call 
425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2014-
0922; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Operations office (telephone 800-647-5527) is in the ADDRESSES section. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Sanjay Ralhan, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-1405; 
fax 425-227-1149.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2014-0922; 
Directorate Identifier 2014-NM-156-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Community, has issued EASA 
Airworthiness Directive 2014-0176, dated July 25, 2014 (referred to 
after this as the Mandatory Continuing Airworthiness Information, or 
``the MCAI''), to correct an unsafe condition on certain Model A319 and 
Model A320 series airplanes. The MCAI states:

    During the A320 fatigue test campaign for Extended Service Goal 
(ESG), it was determined that fatigue damage could appear at certain 
fastener locations on the longeron [area] below the emergency exit 
cut-outs, on the left-hand (LH) and right-hand (RH) sides of the 
fuselage.
    This condition, if not detected and corrected, could affect the 
structural integrity of the aeroplane.
    To address this potential unsafe condition, Airbus developed a 
modification, which has been published through Airbus Service 
Bulletin (SB) A320-53-1265 for in-service application to allow 
aeroplanes to operate up to the new ESG limit.
    For the reasons described above, this [EASA] AD requires 
modification (cold working) of 8 fastener locations in the Longeron 
area (Stringer 20A) below the emergency exit cut-outs on the LH and 
RH sides.
    As described in FAA Advisory Circular 120-104 (http://www.faa.gov/documentLibrary/media/Advisory_Circular/120-104.pdf), several programs 
have been developed to support initiatives that will ensure the 
continued airworthiness of aging airplane structure. The last element 
of those initiatives is the requirement to establish an LOV of the 
engineering data that support the structural maintenance program under 
14 CFR 26.21. This proposed AD is the result of an assessment of the 
previously established programs by DAH during the process of 
establishing the LOV for Airbus Model A319 and A320 series airplanes. 
The

[[Page 74036]]

actions specified in this proposed AD are necessary to complete certain 
programs to ensure the continued airworthiness of aging airplane 
structure and to support an airplane reaching its LOV.
    You may examine the MCAI in the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2014-
0922.

Relevant Service Information

    Airbus has issued Service Bulletin A320-53-1265, Revision 1, dated 
July 2, 2013. The actions described in this service information are 
intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of these 
same type designs.

Costs of Compliance

    We estimate that this proposed AD affects 48 airplanes of U.S. 
registry.
    We also estimate that it would take about 12 work-hours per product 
to comply with the basic requirements of this proposed AD. The average 
labor rate is $85 per work-hour. Required parts would cost $0 per 
product. Based on these figures, we estimate the cost of this proposed 
AD on U.S. operators to be $48,960, or $1,020 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Airbus: Docket No. FAA-2014-0922; Directorate Identifier 2014-NM-
156-AD.

(a) Comments Due Date

    We must receive comments by January 29, 2015.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus airplanes identified in paragraphs 
(c)(1) and (c)(2) of this AD, certificated in any category, all 
manufacturer serial numbers, except those on which Airbus 
modification (mod) 152637 or mod 32208 has been embodied in 
production.
    (1) Airbus Model A319-111, -112, -113, -114, -115, -131, -132, 
and -133 airplanes.
    (2) Airbus Model A320-211, -212, -214, -231, -232, and -233 
airplanes.

(d) Subject

    Air Transport Association (ATA) of America Code 53, Fuselage.

(e) Reason

    This AD was prompted by a report that fatigue cracking could 
appear at certain fastener locations in the longeron area below the 
emergency exit cut-outs. We are issuing this AD to detect and 
correct cracking at certain fastener locations on the longeron, 
which could lead to failure of the fasteners and reduced structural 
integrity of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Modification of Fastener Locations

    Before the accumulation of 48,000 total flight cycles or 96,000 
total flight hours, whichever occurs first since the airplane's 
first flight, modify the 8 fastener locations in the longeron area 
(stringer 20A) below the emergency exit cut-outs on both right-hand 
and left-hand sides, in accordance with the Accomplishment 
Instructions of Airbus Service Bulletin A320-53-1265, Revision 01, 
dated July 2, 2013.

(h) Credit for Previous Actions

    This paragraph provides credit for actions required by paragraph 
(g) of this AD, if those actions were performed before the effective 
date of this AD using Airbus Service Bulletin A320-53-1265, dated 
January 2, 2013, which is not incorporated by reference in this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate ANE-
170, FAA, has the authority to approve AMOCs for this AD, if 
requested using the procedures found in 14 CFR 39.19. In accordance 
with 14 CFR 39.19, send your request to your principal inspector or 
local Flight Standards District Office, as appropriate. If sending 
information directly to the International Branch, send it to ATTN: 
Sanjay Ralhan, Aerospace Engineer, International Branch, ANM-116, 
Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, 
WA 98057-3356; telephone 425-227-1405; fax 425-227-1149. Information 
may be emailed to: [email protected]. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office. The 
AMOC approval letter must specifically reference this AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, International 
Branch, ANM-

[[Page 74037]]

116, Transport Airplane Directorate, FAA; or the European Aviation 
Safety Agency (EASA); or Airbus's EASA Design Organization Approval 
(DOA). If approved by the DOA, the approval must include the DOA-
authorized signature.

(j) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) European Aviation Safety Agency Airworthiness Directive 2014-
0176, dated July 25, 2014, for related information. This MCAI may be 
found in the AD docket on the Internet at http://www.regulations.gov 
by searching for and locating Docket No. FAA-2014-0922.
    (2) For service information identified in this AD, contact 
Airbus, Airworthiness Office--EAS, 1 Rond Point Maurice Bellonte, 
31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 
61 93 44 51; email [email protected]; Internet http://www.airbus.com. You may view this service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. 
For information on the availability of this material at the FAA, 
call 425-227-1221.

    Issued in Renton, Washington, on December 3, 2014.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2014-29233 Filed 12-12-14; 8:45 am]
BILLING CODE 4910-13-P