[Federal Register Volume 79, Number 168 (Friday, August 29, 2014)]
[Rules and Regulations]
[Pages 51501-51503]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2014-20554]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF COMMERCE
National Oceanic and Atmospheric Administration
50 CFR Part 622
Fisheries of the Caribbean, Gulf of Mexico, and South Atlantic
CFR Correction
0
In Title 50 of the Code of Federal Regulations, Parts 600 to 659,
revised as of October 1, 2013, on page 389, Appendix F to Part 622 is
reinstated to read as follows:
Appendix F to Part 622--Specifications for Sea Turtle Mitigation Gear
and Sea Turtle Handling and Release Requirements
A. Sea turtle mitigation gear.
1. Long-handled line clipper or cutter. Line cutters are
intended to cut high test monofilament line as close as possible to
the hook, and assist in removing line from entangled sea turtles to
minimize any remaining gear upon release. NMFS has established
minimum design standards for the line cutters. The LaForce line
cutter and the Arceneaux line clipper are models that meet these
minimum design standards, and may be purchased or fabricated from
readily available and low-cost materials. One long-handled line
clipper or cutter and a set of replacement blades are required to be
onboard. The minimum design standards for line cutters are as
follows:
(a) A protected and secured cutting blade. The cutting blade(s)
must be capable of cutting 2.0-2.1 mm (0.078 in.-0.083 in.)
monofilament line (400-lb test) or polypropylene multistrand
material, known as braided or tarred mainline, and must be
maintained in working order. The cutting blade must be curved,
recessed, contained in a holder, or otherwise designed to facilitate
its safe use so that direct contact between the cutting surface and
the sea turtle or the user is prevented. The cutting instrument must
be securely attached to an extended reach handle and be easily
replaceable. One extra set of replacement blades meeting these
standards must also be carried on board to replace all cutting
surfaces on the line cutter or clipper.
(b) An extended reach handle. The line cutter blade must be
securely fastened to an extended reach handle or pole with a minimum
length equal to, or greater than, 150 percent of the freeboard, or a
minimum of 6 ft (1.83 m), whichever is greater. It is recommended,
but not required, that the handle break down into sections. There is
no restriction on the type of material used to construct this handle
as long as it is sturdy and facilitates the secure attachment of the
cutting blade.
2. Long-handled dehooker for internal hooks. A long-handled
dehooking device is intended to remove internal hooks from sea
turtles that cannot be boated. It should also be used to engage a
loose hook when a turtle is entangled but not hooked, and line is
being removed. The design must shield the barb of the hook and
prevent it from re-engaging during the removal process. One long-
handled device to remove internal hooks is required onboard. The
minimum design standards are as follows:
(a) Hook removal device. The hook removal device must be
constructed of approximately \3/16\-inch (4.76 mm) to \5/16\-inch
(7.94 mm) 316 L stainless steel or similar material and have a
dehooking end no larger than 1 \7/8\-inches (4.76 cm) outside
diameter. The device must securely engage and control the leader
while shielding the barb to prevent the hook from re-engaging during
removal. It may not have any unprotected terminal points (including
blunt ones), as these could cause injury to the esophagus during
hook removal. The device must be of a size appropriate to secure the
range of hook sizes and styles used in the South Atlantic snapper-
grouper fishery.
(b) Extended reach handle. The dehooking end must be securely
fastened to an extended reach handle or pole with a minimum length
equal to or greater than 150 percent of the freeboard, or a minimum
of 6 ft (1.83 m), whichever is greater. It is recommended, but not
required, that the handle break down into sections. The handle must
be sturdy and strong enough to facilitate the secure attachment of
the hook removal device.
3. Long-handled dehooker for external hooks. A long-handled
dehooker is required for use on externally-hooked sea turtles that
cannot be boated. The long-handled dehooker for internal hooks
described in paragraph 2. of this Appendix F would meet this
requirement. The minimum design standards are as follows:
(a) Construction. A long-handled dehooker must be constructed of
approximately \3/16\-inch (4.76 mm) to \5/16\-inch (7.94 mm) 316 L
stainless steel rod and have a dehooking end no larger than 1 \7/8\-
inches (4.76 cm) outside diameter. The design should be such that a
fish hook can be rotated out, without pulling it out at an angle.
The dehooking end must be blunt with all edges rounded. The device
must be of a size appropriate to secure the range of hook sizes and
styles used in the South Atlantic snapper-grouper fishery.
(b) Extended reach handle. The handle must be a minimum length
equal to the freeboard of the vessel or 6 ft (1.83 m), whichever is
greater.
4. Long-handled device to pull an ``inverted V''. This tool is
used to pull a ``V'' in the fishing line when implementing the
``inverted V''; dehooking technique, as described in the document
entitled ``Careful Release Protocols for Sea Turtle Release With
Minimal Injury,'' for disentangling and dehooking entangled sea
turtles. One long-handled device to pull an ``inverted V'' is
required onboard. If a 6-ft (1.83 m) J-style dehooker is used to
comply with paragraph 4. of this Appendix F, it will also satisfy
this requirement. Minimum design standards are as follows:
(a) Hook end. This device, such as a standard boat hook, gaff,
or long-handled J-style dehooker, must be constructed of stainless
steel or aluminum. The semicircular or ``J'' shaped end must be
securely attached to a handle. A sharp point, such as on a gaff
hook, is to be used only for holding the
[[Page 51502]]
monofilament fishing line and should never contact the sea turtle.
(b) Extended reach handle. The handle must have a minimum length
equal to the freeboard of the vessel, or 6 ft (1.83 m), whichever is
greater. The handle must be sturdy and strong enough to facilitate
the secure attachment of the gaff hook.
5. Dipnet. One dipnet is required onboard. Dipnets are to be
used to facilitate safe handling of sea turtles by allowing them to
be brought onboard for fishing gear removal, without causing further
injury to the animal. Turtles must not be brought onboard without
the use of a dipnet or hoist. The minimum design standards for
dipnets are as follows:
(a) Size of dipnet. The dipnet must have a sturdy net hoop of at
least 31 inches (78.74 cm) inside diameter and a bag depth of at
least 38 inches (96.52 cm) to accommodate turtles below 3 ft (0.914
m) carapace length. The bag mesh openings may not exceed 3 inches
(7.62 cm) by 3 inches (7.62 cm). There must be no sharp edges or
burrs on the hoop, or where it is attached to the handle. There is
no requirement for the hoop to be circular as long as it meets the
minimum specifications.
(b) Extended reach handle. The dipnet hoop must be securely
fastened to an extended reach handle or pole with a minimum length
equal to, or greater than, 150 percent of the freeboard, or at least
6 ft (1.83 m), whichever is greater. The handle must be made of a
rigid material strong enough to facilitate the sturdy attachment of
the net hoop and be able to support a minimum of 100 lb (34.1 kg)
without breaking or significant bending or distortion. It is
recommended, but not required, that the extended reach handle break
down into sections.
6. Cushion/support device. A standard automobile tire (free of
exposed steel belts), a boat cushion, a large turtle hoist, or any
other comparable cushioned elevated surface, is required for
supporting a turtle in an upright orientation while the turtle is
onboard. The cushion/support device must be appropriately sized to
fully support a range of turtle sizes.
7. Short-handled dehooker for internal hooks. One short-handled
device for removing internal hooks is required onboard. This
dehooker is designed to remove ingested hooks from boated sea
turtles. It can also be used on external hooks or hooks in the front
of the mouth. Minimum design standards are as follows:
(a) Hook removal device. The hook removal device must be
constructed of approximately \3/16\-inch (4.76 mm) to \5/16\-inch
(7.94 mm) 316 L stainless steel, and must allow the hook to be
secured and the barb shielded without re-engaging during the removal
process. It must be no larger than 1 \7/8\-inches (4.76 cm) outside
diameter. It may not have any unprotected terminal points (including
blunt ones), as this could cause injury to the esophagus during hook
removal. A sliding PVC bite block must be used to protect the beak
and facilitate hook removal if the turtle bites down on the
dehooking device. The bite block should be constructed of a \3/4\-
inch (1.91 cm) inside diameter high impact plastic cylinder (e.g.,
Schedule 80 PVC) that is 4 to 6 inches (10.2 to 15.2 cm) long to
allow for 5 inches (12.7 cm) of slide along the shaft. The device
must be of a size appropriate to secure the range of hook sizes and
styles used in the South Atlantic snapper-grouper fishery.
(b) Handle length. The handle should be approximately 16 to 24
inches (40.64 cm to 60.69 cm) in length, with approximately a 4 to
6-inch (10.2 to 15.2-cm) long tube T-handle of approximately 1 inch
(2.54 cm) in diameter.
8. Short-handled dehooker for external hooks. One short-handled
dehooker for external hooks is required onboard. The short-handled
dehooker for internal hooks required to comply with paragraph 7. of
this Appendix F will also satisfy this requirement. Minimum design
standards are as follows:
(a) Hook removal device. The dehooker must be constructed of
approximately \3/16\-inch (4.76 cm) to \5/16\-inch (7.94 cm) 316 L
stainless steel, and the design must be such that a hook can be
rotated out without pulling it out at an angle. The dehooking end
must be blunt, and all edges rounded. The device must be of a size
appropriate to secure the range of hook sizes and styles used in the
South Atlantic snapper-grouper fishery.
(b) Handle length. The handle should be approximately 16 to 24
inches (40.64 to 60.69 cm) long with approximately a 5-inch (12.7
cm) long tube T-handle, wire loop handle or similar, of
approximately 1 inch (2.54 cm) in diameter.
9. Long-nose or needle-nose pliers. One pair of long-nose or
needle-nose pliers is required on board. Required long-nose or
needle-nose pliers can be used to remove deeply embedded hooks from
the turtle's flesh that must be twisted during removal or for
removing hooks from the front of the mouth. They can also hold PVC
splice couplings, when used as mouth openers, in place. Minimum
design standards are as follows:
(a) General. They must be approximately 12 inches (30.48 cm) in
length, and should be constructed of stainless steel material.
(b) [Reserved]
10. Bolt cutters. One pair of bolt cutters is required on board.
Required bolt cutters may be used to cut hooks to facilitate their
removal. They should be used to cut off the eye or barb of a hook,
so that it can safely be pushed through a sea turtle without causing
further injury. They should also be used to cut off as much of the
hook as possible, when the remainder of the hook cannot be removed.
Minimum design standards are as follows:
(a) General. They must be approximately 14 to 17 inches (35.56
to 43.18 cm) in total length, with approximately 4-inch (10.16 cm)
long blades that are 2\1/4\ inches (5.72 cm) wide, when closed, and
with approximately 10 to 13-inch (25.4 to 33.02-cm) long handles.
Required bolt cutters must be able to cut hard metals, such as
stainless or carbon steel hooks, up to \1/4\-inch (6.35 mm)
diameter.
(b) [Reserved]
11. Monofilament line cutters. One pair of monofilament line
cutters is required on board. Required monofilament line cutters
must be used to remove fishing line as close to the eye of the hook
as possible, if the hook is swallowed or cannot be removed. Minimum
design standards are as follows:
(a) General. Monofilament line cutters must be approximately
7\1/2\ inches (19.05 cm) in length. The blades must be 1 inch (4.45
cm) in length and \5/8\ inches (1.59 cm) wide, when closed.
(b) [Reserved]
12. Mouth openers/mouth gags. Required mouth openers and mouth
gags are used to open sea turtle mouths, and to keep them open when
removing internal hooks from boated turtles. They must allow access
to the hook or line without causing further injury to the turtle.
Design standards are included in the item descriptions. At least two
of the seven different types of mouth openers/gags described below
are required:
(a) A block of hard wood. Placed in the corner of the jaw, a
block of hard wood may be used to gag open a turtle's mouth. A
smooth block of hard wood of a type that does not splinter (e.g.
maple) with rounded edges should be sanded smooth, if necessary, and
soaked in water to soften the wood. The dimensions should be
approximately 11 inches (27.94 cm) by 1 inch (2.54 cm) by 1 inch
(2.54 cm). A long-handled, wire shoe brush with a wooden handle, and
with the wires removed, is an inexpensive, effective and practical
mouth-opening device that meets these requirements.
(b) A set of three canine mouth gags. Canine mouth gags are
highly recommended to hold a turtle's mouth open, because the gag
locks into an open position to allow for hands-free operation after
it is in place. These tools are only for use on small and medium
sized turtles, as larger turtles may be able to crush the mouth gag.
A set of canine mouth gags must include one of each of the following
sizes: Small (5 inches) (12.7 cm), medium (6 inches) (15.24 cm), and
large (7 inches) (17.78 cm). They must be constructed of stainless
steel. The ends must be covered with clear vinyl tubing, friction
tape, or similar, to pad the surface.
(c) A set of two sturdy dog chew bones. Placed in the corner of
a turtle's jaw, canine chew bones are used to gag open a sea
turtle's mouth. Required canine chews must be constructed of durable
nylon, zylene resin, or thermoplastic polymer, and strong enough to
withstand biting without splintering. To accommodate a variety of
turtle beak sizes, a set must include one large (5\1/2\-8 inches
(13.97 cm-20.32 cm) in length), and one small (3\1/2\-4\1/2\ inches
(8.89 cm-11.43 cm) in length) canine chew bones.
(d) A set of two rope loops covered with protective tubing. A
set of two pieces of poly braid rope covered with light duty garden
hose or similar flexible tubing each tied or spliced into a loop to
provide a one-handed method for keeping the turtle's mouth open
during hook and/or line removal. A required set consists of two 3-ft
(0.91 m) lengths of poly braid rope (\3/8\-inch (9.52 mm) diameter
suggested), each covered with an 8-inch (20.32 cm) section of \1/2\
inch (1.27 cm) or \3/4\ inch (1.91 cm) tubing, and each tied into a
loop. The upper loop of rope covered with hose is secured on the
upper beak to give control with one hand, and the second piece
[[Page 51503]]
of rope covered with hose is secured on the lower beak to give
control with the user's foot.
(e) A hank of rope. Placed in the corner of a turtle's jaw, a
hank of rope can be used to gag open a sea turtle's mouth. A 6-ft
(1.83 m) lanyard of approximately \3/16\-inch (4.76 mm) braided
nylon rope may be folded to create a hank, or looped bundle, of
rope. Any size soft-braided nylon rope is allowed, however it must
create a hank of approximately 2-4 inches (5.08 cm-10.16 cm) in
thickness.
(f) A set of four PVC splice couplings. PVC splice couplings can
be positioned inside a turtle's mouth to allow access to the back of
the mouth for hook and line removal. They are to be held in place
with the needle-nose pliers. To ensure proper fit and access, a
required set must consist of the following Schedule 40 PVC splice
coupling sizes: 1 inch (2.54 cm), 1\1/4\ inch (3.18 cm), 1\1/2\ inch
(3.81 cm), and 2 inches (5.08 cm).
(g) A large avian oral speculum. A large avian oral speculum
provides the ability to hold a turtle's mouth open and to control
the head with one hand, while removing a hook with the other hand.
The avian oral speculum must be 9-inches (22.86 cm) long, and
constructed of \3/16\-inch (4.76 mm) wire diameter surgical
stainless steel (Type 304). It must be covered with 8 inches (20.32
cm) of clear vinyl tubing (\5/16\-inch (7.9 mm) outside diameter,
\3/16\-inch (4.76 mm) inside diameter), friction tape, or similar to
pad the surface.
B. Sea turtle handling and release requirements. Sea turtle
bycatch mitigation gear, as specified in paragraphs A.1. through 4.
of this Appendix F, must be used to disengage any hooked or
entangled sea turtles that cannot be brought onboard. Sea turtle
bycatch mitigation gear, as specified in paragraphs A.5. through 12.
of this Appendix F, must be used to facilitate access, safe
handling, disentanglement, and hook removal or hook cutting of sea
turtles that can be brought onboard, where feasible. Sea turtles
must be handled, and bycatch mitigation gear must be used, in
accordance with the careful release protocols and handling/release
guidelines provided by NMFS and in accordance with the onboard
handling and resuscitation requirements specified in Sec.
223.206(d)(1)of this title.
1. Boated turtles. When practicable, active and comatose sea
turtles must be brought on board, with a minimum of injury, using a
dipnet as specified in paragraph A.5. of this Appendix F. All
turtles less than 3 ft (.91 m) carapace length should be boated, if
sea conditions permit.
(a) A boated turtle should be placed on a cushioned/support
device, as specified in paragraph A.6. of this Appendix F, in an
upright orientation to immobilize it and facilitate gear removal.
Then, it should be determined if the hook can be removed without
causing further injury. All externally embedded hooks should be
removed, unless hook removal would result in further injury to the
turtle. No attempt to remove a hook should be made if it has been
swallowed and the insertion point is not visible, or if it is
determined that removal would result in further injury. If a hook
cannot be removed, as much line as possible should be removed from
the turtle using monofilament cutters as specified in paragraph
A.11. of this Appendix F, and the hook should be cut as close as
possible to the insertion point before releasing the turtle, using
bolt cutters as specified in paragraph A.10. of this Appendix F. If
a hook can be removed, an effective technique may be to cut off
either the barb, or the eye, of the hook using bolt cutters, and
then to slide the hook out. When the hook is visible in the front of
the mouth, a mouth-opener, as specified in paragraph A.12. of this
Appendix F, may facilitate opening the turtle's mouth and a gag may
facilitate keeping the mouth open. Short-handled dehookers for
internal hooks, or long-nose or needle-nose pliers, as specified in
paragraphs A.7. and A.8. of this Appendix F, respectively, should be
used to remove visible hooks from the mouth that have not been
swallowed on boated turtles, as appropriate. As much gear as
possible must be removed from the turtle without causing further
injury prior to its release. Refer to the careful release protocols
and handling/release guidelines required in Sec. 622.10(c)(1), and
the handling and resuscitation requirements specified in Sec.
223.206(d)(1) of this title, for additional information.
(b) [Reserved]
2. Non-boated turtles. If a sea turtle is too large, or hooked
in a manner that precludes safe boating without causing further
damage or injury to the turtle, sea turtle bycatch mitigation gear
specified in paragraphs A.1. through 4. of this Appendix F must be
used to disentangle sea turtles from fishing gear and disengage any
hooks, or to clip the line and remove as much line as possible from
a hook that cannot be removed, prior to releasing the turtle, in
accordance with the protocols specified in Sec. 622.10(c)(1).
(a) Non-boated turtles should be brought close to the boat and
provided with time to calm down. Then, it must be determined whether
or not the hook can be removed without causing further injury. All
externally embedded hooks must be removed, unless hook removal would
result in further injury to the turtle. No attempt should be made to
remove a hook if it has been swallowed, or if it is determined that
removal would result in further injury. If the hook cannot be
removed and/or if the animal is entangled, as much line as possible
must be removed prior to release, using a line cutter as specified
in paragraph A.1. of this Appendix F. If the hook can be removed, it
must be removed using a long-handled dehooker as specified in
paragraphs A.2. and A.3. of this Appendix F. Without causing further
injury, as much gear as possible must be removed from the turtle
prior to its release. Refer to the careful release protocols and
handling/release guidelines required in Sec. 622.10(c)(1), and the
handling and resuscitation requirements specified in Sec.
223.206(d)(1) for additional information.
(b) [Reserved]
[FR Doc. 2014-20554 Filed 8-28-14; 8:45 am]
BILLING CODE 1505-01-D