[Federal Register Volume 79, Number 158 (Friday, August 15, 2014)]
[Rules and Regulations]
[Pages 48018-48021]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2014-19263]



[[Page 48018]]

=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2014-0531; Directorate Identifier 2014-NM-142-AD; 
Amendment 39-17940; AD 2014-16-16]
RIN 2120-AA64


Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. 
(Embraer) Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for all 
Embraer S.A. Model ERJ 190-100 STD, -100 LR, -100 ECJ, -100 IGW, -200 
STD, -200 LR, and -200 IGW airplanes. This AD requires, for certain 
airplanes, retorquing and replacing the pylon outboard and inboard 
lower link fittings. For all airplanes, this AD requires repetitive 
retorquing of the pylon outboard and inboard lower link fittings. This 
AD was prompted by a report of a loose lower link assembly on the left 
and right pylons. We are issuing this AD to prevent loss of a shear pin 
on the pylon outboard and inboard lower link fittings, which could 
result in failure of the fitting and consequent separation of the 
engine from the wing.

DATES: This AD becomes effective September 2, 2014.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in this AD as of September 2, 
2014.
    We must receive comments on this AD by September 29, 2014.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this AD, contact Embraer 
S.A., Technical Publications Section (PC 060), Av. Brigadeiro Faria 
Lima, 2170--Putim--12227-901 S[atilde]o Jose dos Campos--SP--Brazil; 
telephone +55 12 3927-5852 or +55 12 3309-0732; fax +55 12 3927-7546; 
email [email protected]; Internet http://www.flyembraer.com. You 
may view this referenced service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information 
on the availability of this material at the FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2014-
0531; or in person at the Docket Operations office between 9 a.m. and 5 
p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this AD, the regulatory evaluation, any comments received, and 
other information. The street address for the Docket Operations office 
(telephone 800-647-5527) is in the ADDRESSES section. Comments will be 
available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Kathrine Rask, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-2180; 
fax 425-227-1149.

SUPPLEMENTARY INFORMATION: 

Discussion

    The Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil (ANAC), 
which is the aviation authority for Brazil, has issued Brazilian 
Airworthiness Directive 2014-07-01, dated July 10, 2014 (referred to 
after this as the Mandatory Continuing Airworthiness Information, or 
``the MCAI''), to correct an unsafe condition on all Embraer S.A. Model 
ERJ 190-100 STD, -100 LR, -100 ECJ, -100 IGW, -200 STD, -200 LR, and -
200 IGW airplanes. The MCAI states:

    It has been found that repetitive tightening torque check 
required by EAD 2014-06-02--EMBRAER S.A./39-1383 may not be 
sufficient to prevent the lower inboard and outboard link fitting 
attaching parts, of the left hand (LH) and right hand (RH) pylon, 
from getting loose which could lead to the failure of one of those 
fittings and the consequent separation of the engine from the wing.

Required actions include retorquing and replacing the pylon outboard 
and inboard lower link fittings on certain airplanes, and repetitively 
retorquing the pylon outboard and inboard lower link fittings on all 
airplanes. You may examine the MCAI on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2014-
0531.

Relevant Service Information

    Embraer has issued the following service information:
     Embraer Alert Service Bulletin 190-54-A015, Revision 03, 
dated June 27, 2014.
     Embraer Alert Service Bulletin 190LIN-54-A006, Revision 
02, dated June 27, 2014.
     Embraer Service Bulletin 190-54-0013, dated November 27, 
2012.
     Embraer Service Bulletin 190-54-0015, dated July 3, 2014.
     Embraer Service Bulletin 190LIN-54-0004, dated December 
20, 2012.
     Embraer Service Bulletin 190LIN-54-0006, dated July 3, 
2014.

The actions described in this service information are intended to 
correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of this AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are issuing this AD because we 
evaluated all pertinent information and determined the unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Difference Between This AD and the MCAI or Service Information

    The applicability of the MCAI does not include production 
airplanes. This FAA AD, however, applies to all airplanes of the 
affected models to ensure that the repetitive retorquing is done on the 
fleet (as specified in paragraph (i) of this AD) and to prohibit the 
installation of certain lock nuts on any airplane in the fleet (as 
specified in paragraph (j) of this AD).
    The airplanes affected by paragraph (g)(2) of this AD include one 
airplane (serial number 19000641) that is not included in the 
corresponding requirement of the ANAC AD. For the airplanes affected by 
this requirement, the ANAC AD refers to Embraer Alert Service Bulletin 
190LIN-54-A006, Revision 02, dated June 27, 2014. This FAA AD, however, 
refers to the most recent service information--Embraer Service Bulletin 
190LIN-54-0006, dated July 3, 2014, which includes this

[[Page 48019]]

additional airplane. This has been coordinated with ANAC.

``Contacting the Manufacturer'' Paragraph in This AD

    Since late 2006, we have included a standard paragraph titled 
``Airworthy Product'' in all MCAI ADs in which the FAA develops an AD 
based on a foreign authority's AD.
    The MCAI or referenced service information in an FAA AD often 
directs the owner/operator to contact the manufacturer for corrective 
actions, such as a repair. Briefly, the Airworthy Product paragraph 
allowed owners/operators to use corrective actions provided by the 
manufacturer if those actions were FAA-approved. In addition, the 
paragraph stated that any actions approved by the State of Design 
Authority (or its delegated agent) are considered to be FAA-approved.
    In an NPRM having Directorate Identifier 2012-NM-101-AD (78 FR 
78285, December 26, 2013), we proposed to prevent the use of repairs 
that were not specifically developed to correct the unsafe condition, 
by requiring that the repair approval provided by the State of Design 
Authority or its delegated agent specifically refer to the FAA AD. This 
change was intended to clarify the method of compliance and to provide 
operators with better visibility of repairs that are specifically 
developed and approved to correct the unsafe condition. In addition, we 
proposed to change the phrase ``its delegated agent'' to include a 
design approval holder (DAH) with State of Design Authority design 
organization approval (DOA), as applicable, to refer to a DAH 
authorized to approve required repairs for the proposed AD.
    One commenter to the NPRM having Directorate Identifier 2012-NM-
101-AD (78 FR 78285, December 26, 2013) stated the following: ``The 
proposed wording, being specific to repairs, eliminates the 
interpretation that Airbus messages are acceptable for approving minor 
deviations (corrective actions) needed during accomplishment of an AD 
mandated Airbus service bulletin.''
    This comment has made the FAA aware that some operators have 
misunderstood or misinterpreted the Airworthy Product paragraph to 
allow the owner/operator to use messages provided by the manufacturer 
as approval of deviations during the accomplishment of an AD-mandated 
action. The Airworthy Product paragraph does not approve messages or 
other information provided by the manufacturer for deviations to the 
requirements of the AD-mandated actions. The Airworthy Product 
paragraph only addresses the requirement to contact the manufacturer 
for corrective actions for the identified unsafe condition and does not 
cover deviations from other AD requirements. However, deviations to AD-
required actions are addressed in 14 CFR 39.17, and anyone may request 
the approval for an alternative method of compliance to the AD-required 
actions using the procedures found in 14 CFR 39.19.
    To address this misunderstanding and misinterpretation of the 
Airworthy Product paragraph, we have changed the paragraph and retitled 
it ``Contacting the Manufacturer.'' This paragraph now clarifies that 
for any requirement in this AD to obtain corrective actions from a 
manufacturer, the actions must be accomplished using a method approved 
by the FAA, ANAC, or ANAC's authorized Designee.
    The Contacting the Manufacturer paragraph also clarifies that, if 
approved by the ANAC Designee, the approval must include the Designee's 
authorized signature. The Designee's signature indicates that the data 
and information contained in the document are ANAC-approved, which is 
also FAA-approved. Messages and other information provided by the 
manufacturer that do not contain the ANAC Designee's authorized 
signature approval are not ANAC-approved, unless ANAC directly approves 
the manufacturer's message or other information.
    This clarification does not remove flexibility previously afforded 
by the Airworthy Product paragraph. Consistent with long-standing FAA 
policy, such flexibility was never intended for required actions. This 
is also consistent with the recommendation of the Airworthiness 
Directive Implementation Aviation Rulemaking Committee to increase 
flexibility in complying with ADs by identifying those actions in 
manufacturers' service instructions that are ``Required for 
Compliance'' with ADs. We continue to work with manufacturers to 
implement this recommendation. But once we determine that an action is 
required, any deviation from the requirement must be approved as an 
alternative method of compliance.

Interim Action

    We consider this AD interim action. If final action is later 
identified, we might consider further rulemaking then.

FAA's Determination of the Effective Date

    An unsafe condition exists that requires the immediate adoption of 
this AD. The FAA has found that the risk to the flying public justifies 
waiving notice and comment prior to adoption of this rule because loss 
of a shear pin on the pylon outboard and inboard lower link fittings 
could result in failure of the fitting and consequent separation of the 
engine from the wing. Therefore, we determined that notice and 
opportunity for public comment before issuing this AD are impracticable 
and that good cause exists for making this amendment effective in less 
than 30 days.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety, and we did not precede it by notice and opportunity for public 
comment. We invite you to send any written relevant data, views, or 
arguments about this AD. Send your comments to an address listed under 
the ADDRESSES section. Include ``Docket No. FAA-2014-0531; Directorate 
Identifier 2014-NM-142-AD'' at the beginning of your comments. We 
specifically invite comments on the overall regulatory, economic, 
environmental, and energy aspects of this AD. We will consider all 
comments received by the closing date and may amend this AD based on 
those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this AD.

Costs of Compliance

    We estimate that this AD affects 86 airplanes of U.S. registry. We 
also estimate that it will take about 6 work-hours per product to 
comply with the basic requirements of this AD. Required parts will cost 
about $0. The average labor rate is $85 per work-hour. Based on these 
figures, we estimate the cost of this AD on U.S. operators to be 
$43,860, or $510 per product.
    According to the manufacturer, some of the costs of this AD may be 
covered under warranty, thereby reducing the cost impact on affected 
individuals. We do not control warranty coverage for affected 
individuals. As a result, we have included all costs in our cost 
estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more

[[Page 48020]]

detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2014-16-16 Embraer S.A.: Amendment 39-17940. Docket No. FAA-2014-
0531; Directorate Identifier 2014-NM-142-AD.

(a) Effective Date

    This AD becomes effective September 2, 2014.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all Embraer S.A. Model ERJ 190-100 STD, -100 
LR, -100 ECJ, -100 IGW, -200 STD, -200 LR, and -200 IGW airplanes, 
certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 54, Nacelles/
Pylons.

(e) Reason

    This AD was prompted by a report of a loose lower link assembly 
on the left and right pylons. We are issuing this AD to prevent loss 
of a shear pin on the pylon outboard and inboard lower link 
fittings, which could result in failure of the fitting and 
consequent separation of the engine from the wing.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Initial Retorque

    Retorque the left and right pylon outboard and inboard lower 
link fittings, as specified in paragraph (g)(1) or (g)(2) of this 
AD, as applicable.
    (1) For airplanes identified as Groups 1 and 2 in Embraer 
Service Bulletin 190-54-0015, dated July 3, 2014: Retorque at the 
applicable time specified in paragraph (g)(1)(i) or (g)(1)(ii) of 
this AD, in accordance with the Accomplishment Instructions of 
Embraer Alert Service Bulletin 190-54-A015, Revision 03, dated June 
27, 2014.
    (i) For Group 1 airplanes: Retorque at the applicable time 
specified in paragraph (g)(1)(i)(A) or (g)(1)(i)(B) of this AD.
    (A) If, as of the effective date of this AD, the airplane has 
accumulated fewer than 600 total flight cycles and less than 750 
total flight hours since accomplishment of the actions specified in 
Embraer Service Bulletin 190-54-0013: Retorque within 50 flight 
hours after the effective date of this AD.
    (B) If, as of the effective date of this AD, the airplane has 
accumulated 600 or more total flight cycles or 750 or more total 
flight hours after accomplishment of Embraer Service Bulletin 190-
54-0013: Retorque within 10 flight hours after the effective date of 
this AD.
    (ii) For Group 2 airplanes: Retorque at the applicable time 
specified in paragraph (g)(1)(ii)(A) or (g)(1)(ii)(B) of this AD.
    (A) If, as of the effective date of this AD, the airplane has 
accumulated fewer than 600 total flight cycles and less than 750 
total flight hours: Retorque within 50 flight hours after the 
effective date of this AD.
    (B) If, as of the effective date of this AD, the airplane has 
accumulated 600 or more total flight cycles or 750 or more total 
flight hours: Retorque within 10 flight hours after the effective 
date of this AD.
    (2) For airplanes identified as Groups 1 and 2 in Embraer 
Service Bulletin 190LIN-54-0006, dated July 3, 2014: Retorque at the 
applicable time specified in paragraph (g)(2)(i) or (g)(2)(ii) of 
this AD, in accordance with the Accomplishment Instructions of 
Embraer Alert Service Bulletin 190LIN-54-A006, Revision 02, dated 
June 27, 2014.
    (i) For Group 1 airplanes: Retorque at the applicable time 
specified in paragraph (g)(2)(i)(A) or (g)(2)(i)(B) of this AD.
    (A) If, as of the effective date of this AD, the airplane has 
accumulated fewer than 200 total flight cycles and less than 750 
total flight hours since accomplishment of the actions specified in 
Embraer Service Bulletin 190LIN-54-0004: Retorque within 50 flight 
hours after the effective date of this AD.
    (B) If, as of the effective date of this AD, the airplane has 
accumulated 200 or more total flight cycles or 750 or more total 
flight hours since accomplishment of the actions specified in 
Embraer Service Bulletin 190LIN-54-0004: Retorque within 10 flight 
hours after the effective date of this AD.
    (ii) For Group 2 airplanes: Retorque at the applicable time 
specified in (g)(2)(ii)(A) or (g)(2)(ii)(B) of this AD.
    (A) If, as of the effective date of this AD, the airplane has 
accumulated fewer than 200 total flight cycles and less than 750 
total flight hours: Retorque within 50 flight hours after the 
effective date of this AD.
    (B) If, as of the effective date of this AD, the airplane has 
accumulated 200 or more total flight cycles or 750 or more total 
flight hours: Retorque within 10 flight hours after the effective 
date of this AD.

(h) Replacement

    Replace the left and right pylon outboard and inboard lower link 
fittings as specified in paragraph (h)(1) or (h)(2), as applicable.
    (1) For airplanes identified as Groups 1 and 2 in Embraer 
Service Bulletin 190-54-0015, dated July 3, 2014: Within 150 flight 
cycles or 200 flight hours, whichever occurs first after the 
effective date of this AD, replace the pylon outboard and inboard 
lower link fittings, in accordance with Parts I and II of the 
Accomplishment Instructions of Embraer Service Bulletin 190-54-0015, 
dated July 3, 2014.
    (2) For airplanes identified as Groups 1 and 2 in Embraer 
Service Bulletin 190LIN-54-0006, dated July 3, 2014: Within 60 
flight cycles or 200 flight hours, whichever occurs first after the 
effective date of this AD, replace the pylon outboard and inboard 
lower link fittings, in accordance with Parts I and II of the 
Accomplishment Instructions of Embraer Service Bulletin 190LIN-54-
0006, dated July 3, 2014.

(i) Repetitive Retorquing

    Retorque the left and right pylon outboard and inboard lower 
link fittings, as specified in paragraph (i)(1) or (i)(2) of this 
AD, as applicable.
    (1) For Model ERJ 190-100 STD, &100 LR, -100 IGW, -200 STD, -200 
LR, and -200 IGW airplanes: Retorque as specified in paragraph 
(i)(1)(i) or (i)(1)(ii) of this AD, as applicable, in accordance 
with Parts III and IV of the Accomplishment Instructions of Embraer 
Service Bulletin 190-54-0015, dated July 3, 2014.
    (i) For airplanes identified as Groups 1 and 2 in Embraer 
Service Bulletin 190-54-0015,

[[Page 48021]]

dated July 3, 2014: Retorque within 6,000 flight cycles or 7,500 
flight hours, whichever occurs first after replacement of the pylon 
outboard and inboard lower link fittings required by paragraph (h) 
of this AD, and thereafter at intervals not to exceed 6,000 flight 
cycles or 7,500 flight hours, whichever occurs first.
    (ii) For airplanes identified as Group 3 in Embraer Service 
Bulletin 190-54-0015, dated July 3, 2014, and Model ERJ 190-100 STD, 
-100 LR, -100 IGW, -200 STD, -200 LR, and -200 IGW airplanes having 
serial numbers 19000586 and subsequent: Retorque within 6,000 flight 
cycles or 7,500 flight hours, whichever occurs first after the 
effective date of this AD, and thereafter at intervals not to exceed 
6,000 flight cycles or 7,500 flight hours, whichever occurs first.
    (2) For Model ERJ 190-100 ECJ airplanes: Retorque as specified 
in paragraph (i)(2)(i) or (i)(2)(ii) of this AD, as applicable, in 
accordance with Parts III and IV of the Accomplishment Instructions 
of Embraer Service Bulletin 190LIN-54-0006, dated July 3, 2014.
    (i) For airplanes identified as Groups 1 and 2 in Embraer 
Service Bulletin 190LIN-54-0006, dated July 3, 2014: Retorque within 
2,000 flight cycles or 7,500 flight hours, whichever occurs first 
after replacement of the pylon outboard and inboard lower link 
fittings required by paragraph (h) of this AD, and thereafter at 
intervals not to exceed 2,000 flight cycles or 7,500 flight hours, 
whichever occurs first.
    (ii) For airplanes identified as Group 3 in Embraer Service 
Bulletin 190LIN-54-0006, dated July 3, 2014, and Model ECJ airplanes 
having serial numbers 19000572 and subsequent: Retorque within 2,000 
flight cycles or 7,500 flight hours, whichever occurs first after 
the effective date of this AD, and thereafter at intervals not to 
exceed 2,000 flight cycles or 7,500 flight hours, whichever occurs 
first.

(j) Parts Installation Prohibition

    As of the effective date of this AD, no person may install, at 
the inboard or outboard lower link fitting on any airplane, a lock 
assembly identified in Embraer Service Bulletin 190-54-0013, dated 
November 27, 2012; or Embraer Service Bulletin 190LIN-54-0004, dated 
December 20, 2012.

(k) Credit for Previous Actions

    This paragraph provides credit for the actions specified in 
paragraph (g) of this AD, if those actions were performed before the 
effective date of this AD using the service information specified in 
paragraphs (k)(1) through (k)(5) of this AD, as applicable. This 
service information is not incorporated by reference in this AD.
    (1) Embraer Alert Service Bulletin 190-54-A015, dated June 23, 
2014.
    (2) Embraer Alert Service Bulletin 190-54-A015, Revision 01, 
dated June 26, 2014.
    (3) Embraer Alert Service Bulletin 190-54-A015, Revision 02, 
dated June 27, 2014.
    (4) Embraer Alert Service Bulletin 190LIN-54-A006, dated June 
23, 2014.
    (5) Embraer Alert Service Bulletin 190LIN-54-A006, Revision 01, 
dated June 26, 2014.

(l) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. In accordance with 14 CFR 
39.19, send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Branch, send it to ATTN: Kathrine 
Rask, Aerospace Engineer, International Branch, ANM-116, Transport 
Airplane Directorate, FAA; telephone 425-227-2180; fax 425-227-1149. 
Information may be emailed to [email protected]. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
local flight standards district office/certificate holding district 
office. The AMOC approval letter must specifically reference this 
AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, International 
Branch, ANM-116, Transport Airplane Directorate, FAA; or ANAC; or 
ANAC's authorized Designee. If approved by the ANAC Designee, the 
approval must include the Designee's authorized signature.

(m) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) Brazilian Airworthiness Directive 2014-07-01, dated July 10, 
2014, for related information. You may examine the MCAI on the 
Internet at http://www.regulations.gov by searching for and locating 
Docket No. FAA-2014-0531.
    (2) Service information identified in this AD that is not 
incorporated by reference is available at the addresses specified in 
paragraphs (n)(3) and (n)(4) of this AD.

(n) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Embraer Alert Service Bulletin 190-54-A015, Revision 03, 
dated June 27, 2014.
    (ii) Embraer Alert Service Bulletin 190LIN-54-A006, Revision 02, 
dated June 27, 2014.
    (iii) Embraer Service Bulletin 190-54-0013, dated November 27, 
2012.
    (iv) Embraer Service Bulletin 190-54-0015, dated July 3, 2014.
    (v) Embraer Service Bulletin 190LIN-54-0004, dated December 20, 
2012.
    (vi) Embraer Service Bulletin 190LIN-54-0006, dated July 3, 
2014.
    (3) For service information identified in this AD, contact 
Embraer S.A., Technical Publications Section (PC 060), Av. 
Brigadeiro Faria Lima, 2170--Putim--12227-901 S[atilde]o Jose dos 
Campos--SP--Brasil; telephone +55 12 3927-5852 or +55 12 3309-0732; 
fax +55 12 3927-7546; email [email protected]; Internet http://www.flyembraer.com.
    (4) You may view this service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 
425-227-1221.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to http://www.archives.gov/federal-register/cfr/ibr-locations.html.


    Issued in Renton, Washington, on August 6, 2014.
Victor Wicklund,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2014-19263 Filed 8-14-14; 8:45 am]
BILLING CODE 4910-13-P