[Federal Register Volume 79, Number 158 (Friday, August 15, 2014)]
[Rules and Regulations]
[Pages 48030-48032]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2014-18306]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2013-1068; Directorate Identifier 2013-NM-196-AD; 
Amendment 39-17923; AD 2014-15-20]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc. Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
Bombardier, Inc. Model DHC-8-400 series airplanes. This AD was prompted 
by reports of failure of the high pressure shutoff valves (HPSOVs) 
causing the timer and monitor unit (TMU) to become inoperative since 
the HPSOV and the TMU are on the same circuit breaker. This AD requires 
a wiring modification to segregate the HPSOV power supply from the TMU. 
We are issuing this AD to prevent an inoperative TMU, which could 
result in the loss of the automatic de-icing mode, and lead to an 
increased workload for the flight crew and loss of control of the 
airplane.

DATES: This AD becomes effective September 19, 2014.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of September 
19, 2014.

ADDRESSES: You may examine the AD docket on the Internet at http://www.regulations.gov/#!docketDetail;D=FAA-2013-1068; or in person at the 
Docket Management Facility, U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC.
    For service information identified in this AD, contact Bombardier, 
Inc., Q-Series Technical Help Desk, 123 Garratt Boulevard, Toronto, 
Ontario M3K 1Y5, Canada; telephone 416-375-4000; fax 416-375-4539; 
email [email protected]; Internet http://www.bombardier.com. You may view this referenced service information at 
the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, 
WA. For information on the availability of this material at the FAA, 
call 425-227-1221.

FOR FURTHER INFORMATION CONTACT: Cesar Gomez, Aerospace Engineer, 
Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, NY 
11590; telephone 516-228-7318; fax 516-794-5531.

SUPPLEMENTARY INFORMATION: 

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 by adding an AD that would apply to certain Bombardier, Inc. 
Model DHC-8-400 series airplanes. The NPRM published in the Federal 
Register on January 2, 2014 (79 FR 76). Transport Canada Civil Aviation 
(TCCA), which is the aviation authority for Canada, has issued Canadian 
Airworthiness Directive CF-2013-27, dated September 25, 2013 (referred 
to after this as the Mandatory Continuing Airworthiness Information, or 
``the MCAI''), to correct an unsafe condition for the specified 
products. The MCAI states:

    There have been several in-service reports of the failure of 
high pressure shutoff valves (HPSOV) causing the Timer and Monitor 
Unit (TMU) to become inoperative since the HPSOV and TMU are on the 
same circuit breaker.
    An inoperative TMU would result in the loss of the automatic de-
icing mode and would lead to an increased workload for the 
flightcrew. In the case where additional failures occur during a 
critical flight phase, the significantly increased workload could 
lead to loss of control of the aeroplane.
    This [Canadian] AD mandates a wiring modification to segregate 
the HPSOV power supply from the TMU.

    You may examine the MCAI in the AD docket on the Internet at http://www.regulations.gov/#!documentDetail;D=FAA-2013-1068-0002.

Comments

    We gave the public the opportunity to participate in developing 
this AD. The following presents the comment received on the NPRM (79 FR 
76, January 2, 2014) and the FAA's response to the comment.

Request To Use the Latest Service Information

    Horizon Air requested that we revise the proposed AD (79 FR 76, 
January 2, 2014) to allow compliance for Bombardier Service Bulletin 
84-36-04, Revision B, dated January 2, 2014, or Bombardier Service 
Bulletin 84-36-04, Revision A, dated April 17, 2013.
    We agree with the commenter's request to reference the latest 
service information. We have revised this AD by referencing Bombardier 
Service Bulletin 84-36-04, Revision B, dated January 2, 2014, 
throughout this AD. We have also revised paragraph (h) of this AD to 
give credit for actions done before the effective date of this AD in 
accordance with Bombardier Service Bulletin 84-36-04, Revision A, dated 
April 17, 2013, as well as Bombardier Service Bulletin 84-36-04, dated 
March 13, 2013.

``Contacting the Manufacturer'' Paragraph in This AD

    Since late 2006, we have included a standard paragraph titled 
``Airworthy Product'' in all MCAI ADs in which the FAA develops an AD 
based on a foreign authority's AD.
    The MCAI or referenced service information in an FAA AD often 
directs the owner/operator to contact the manufacturer for corrective 
actions, such as a repair. Briefly, the Airworthy Product paragraph 
allowed owners/operators to use corrective actions provided by the 
manufacturer if those actions were FAA-approved. In addition, the 
paragraph stated that any actions approved by the State of Design 
Authority (or its delegated agent) are considered to be FAA-approved.
    In the NPRM (79 FR 76, January 2, 2014), we proposed to prevent the 
use of repairs that were not specifically developed to correct the 
unsafe condition, by requiring that the repair approval provided by the 
State of Design Authority or its delegated agent specifically refer to 
this FAA AD. This change was intended to clarify the method of 
compliance and to provide operators with better visibility of repairs 
that are specifically developed and approved to correct the unsafe 
condition. In addition, we proposed to change the phrase ``its 
delegated agent'' to include a design approval holder (DAH) with State 
of Design Authority design organization approval (DOA), as applicable, 
to refer to a DAH authorized to approve required repairs for the 
proposed AD.

[[Page 48031]]

    No comments were provided to the NPRM (79 FR 76, January 2, 2014) 
about these proposed changes. However, a comment was provided for an 
NPRM having Directorate Identifier 2012-NM-101-AD (78 FR 78285, 
December 26, 2013). The commenter stated the following: ``The proposed 
wording, being specific to repairs, eliminates the interpretation that 
Airbus messages are acceptable for approving minor deviations 
(corrective actions) needed during accomplishment of an AD mandated 
Airbus service bulletin.''
    This comment has made the FAA aware that some operators have 
misunderstood or misinterpreted the Airworthy Product paragraph to 
allow the owner/operator to use messages provided by the manufacturer 
as approval of deviations during the accomplishment of an AD-mandated 
action. The Airworthy Product paragraph does not approve messages or 
other information provided by the manufacturer for deviations to the 
requirements of the AD-mandated actions. The Airworthy Product 
paragraph only addresses the requirement to contact the manufacturer 
for corrective actions for the identified unsafe condition and does not 
cover deviations from other AD requirements. However, deviations to AD-
required actions are addressed in 14 CFR 39.17, and anyone may request 
the approval for an alternative method of compliance to the AD-required 
actions using the procedures found in 14 CFR 39.19.
    To address this misunderstanding and misinterpretation of the 
Airworthy Product paragraph, we have changed the paragraph and retitled 
it ``Contacting the Manufacturer.'' This paragraph now clarifies that 
for any requirement in this AD to obtain corrective actions from a 
manufacturer, the actions must be accomplished using a method approved 
by the FAA, TCCA, or Bombardier, Inc.'s TCCA Design Approval 
Organization (DAO).
    The Contacting the Manufacturer paragraph also clarifies that, if 
approved by the DAO, the approval must include the DAO-authorized 
signature. The DAO signature indicates that the data and information 
contained in the document are TCCA-approved, which is also FAA-
approved. Messages and other information provided by the manufacturer 
that do not contain the DAO-authorized signature approval are not TCCA-
approved, unless TCCA directly approves the manufacturer's message or 
other information.
    This clarification does not remove flexibility previously afforded 
by the Airworthy Product paragraph. Consistent with long-standing FAA 
policy, such flexibility was never intended for required actions. This 
is also consistent with the recommendation of the Airworthiness 
Directive Implementation Aviation Rulemaking Committee to increase 
flexibility in complying with ADs by identifying those actions in 
manufacturers' service instructions that are ``Required for 
Compliance'' with ADs. We continue to work with manufacturers to 
implement this recommendation. But once we determine that an action is 
required, any deviation from the requirement must be approved as an 
alternative method of compliance.
    Other commenters to the NPRM having Directorate Identifier 2012-NM-
101-AD (78 FR 78285, December 26, 2013) pointed out that in many cases 
the foreign manufacturer's service bulletin and the foreign authority's 
MCAI might have been issued some time before the FAA AD. Therefore, the 
DOA might have provided U.S. operators with an approved repair, 
developed with full awareness of the unsafe condition, before the FAA 
AD is issued. Under these circumstances, to comply with the FAA AD, the 
operator would be required to go back to the manufacturer's DOA and 
obtain a new approval document, adding time and expense to the 
compliance process with no safety benefit.
    Based on these comments, we removed the requirement that the DAH-
provided repair specifically refer to this AD. Before adopting such a 
requirement, the FAA will coordinate with affected DAHs and verify they 
are prepared to implement means to ensure that their repair approvals 
consider the unsafe condition addressed in this AD. Any such 
requirements will be adopted through the normal AD rulemaking process, 
including notice-and-comment procedures, when appropriate.
    We also have decided not to include a generic reference to either 
the ``delegated agent'' or ``DAH with State of Design Authority design 
organization approval,'' but instead we have provided the specific 
delegation approval granted by the State of Design Authority for the 
DAH throughout this AD.

Conclusion

    We reviewed the relevant data, considered the comment received, and 
determined that air safety and the public interest require adopting 
this AD with the changes described previously and minor editorial 
changes. We have determined that these minor changes:
     Are consistent with the intent that was proposed in the 
NPRM (79 FR 76, January 2, 2014) for correcting the unsafe condition; 
and
     Do not add any additional burden upon the public than was 
already proposed in the NPRM (79 FR 76, January 2, 2014).
    We also determined that these changes will not increase the 
economic burden on any operator or increase the scope of this AD.

Costs of Compliance

    We estimate that this AD affects 78 airplanes of U.S. registry.
    We also estimate that it will take about 7 work-hours per product 
to comply with the basic requirements of this AD. The average labor 
rate is $85 per work-hour. Required parts will cost about $0 per 
product. Based on these figures, we estimate the cost of this AD on 
U.S. operators to be $46,410, or $595 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative,

[[Page 48032]]

on a substantial number of small entities under the criteria of the 
Regulatory Flexibility Act.

Examining the AD Docket

    You may examine the AD docket on the Internet at http:/
www.regulations.gov#!docketDetail;D=FAA-2013-1068; or in person at the 
Docket Management Facility between 9 a.m. and 5 p.m., Monday through 
Friday, except Federal holidays. The AD docket contains this AD, the 
regulatory evaluation, any comments received, and other information. 
The street address for the Docket Operations office (telephone 800-647-
5527) is in the ADDRESSES section.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2014-15-20 Bombardier, Inc.: Amendment 39-17923. Docket No. FAA-
2013-1068; Directorate Identifier 2013-NM-196-AD.

(a) Effective Date

    This AD becomes effective September 19, 2014.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc. Model DHC-8-400, -401, and -
402 airplanes, certificated in any category, serial numbers 4001 
through 4446 inclusive.

(d) Subject

    Air Transport Association (ATA) of America Code 36, Pneumatic.

(e) Reason

    This AD was prompted by reports of failure of the high pressure 
shutoff valves (HPSOVs) causing the timer and monitor unit (TMU) to 
become inoperative since the HPSOV and the TMU are on the same 
circuit breaker. We are issuing this AD to prevent an inoperative 
TMU, which could result in the loss of the automatic de-icing mode, 
and lead to an increased workload for the flight crew and loss of 
control of the airplane.

(f) Compliance

    You are responsible for having the actions required by this AD 
performed within the compliance times specified, unless the actions 
have already been done.

(g) Segregation of the HPSOV Power Supply From the TMU

    Within 2,000 flight hours or 12 months after the effective date 
of this AD, whichever occurs first: Do a wiring modification to 
segregate the HPSOV power supply from the TMU, by incorporating 
Bombardier ModSum Package 4-110595, Revision C, dated May 14, 2013, 
in accordance with the Accomplishment Instructions of Bombardier 
Service Bulletin 84-36-04, Revision B, dated January 2, 2014.

(h) Credit for Previous Actions

    This paragraph provides credit for actions required by paragraph 
(g) of this AD, if those actions were performed before the effective 
date of this AD using Bombardier Service Bulletin 84-36-04, dated 
March 13, 2013; or Bombardier Service Bulletin 84-36-04, Revision A, 
dated April 17, 2013.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office (ACO), ANE-170, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the New York ACO, send it to ATTN: Program Manager, 
Continuing Operational Safety, FAA, New York ACO, 1600 Stewart 
Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7300; fax 
516-794-5531. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the local flight standards district officecertificate 
holding district office. The AMOC approval letter must specifically 
reference this AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, New York ACO, 
ANE-170, Engine and Propeller Directorate, FAA; or Transport Canada 
Civil Aviation (TCCA); or Bombardier, Inc.'s TCCA Design Approval 
Organization (DAO). If approved by the DAO, the approval must 
include the DAO-authorized signature.

(j) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) Canadian Airworthiness Directive CF-2013-27, dated September 
25, 2013, for related information. This MCAI may be found in the AD 
docket on the Internet at http:/
www.regulations.gov#!documentDetail;D=FAA-2013-1068-0002.
    (2) Service information identified in this AD that is not 
incorporated by reference may be viewed at the addresses specified 
in paragraphs (k)(3) and (k)(4) of this AD.

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Bombardier Service Bulletin 84-36-04, Revision B, dated 
January 2, 2014.
    (ii) Reserved.
    (3) For service information identified in this AD, contact 
Bombardier, Inc., Q-Series Technical Help Desk, 123 Garratt 
Boulevard, Toronto, Ontario M3K 1Y5, Canada; telephone 416-375-4000; 
fax 416-375-4539; email [email protected]; Internet 
http:/www.bombardier.com.
    (4) You may view this service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 
425-227-1221.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: http:/www.archives.govfederal-
registercfribr-locations.html.


    Issued in Renton, Washington, on July 18, 2014.
John P. Piccola,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2014-18306 Filed 8-14-14; 8:45 am]
BILLING CODE 4910-13-P