[Federal Register Volume 79, Number 149 (Monday, August 4, 2014)]
[Rules and Regulations]
[Pages 45288-45307]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2014-17975]



[[Page 45287]]

Vol. 79

Monday,

No. 149

August 4, 2014

Part IV





Department of Commerce





-----------------------------------------------------------------------





Bureau of Industry and Security





-----------------------------------------------------------------------





15 CFR Parts 734, 738, 740 et al.





 Wassenaar Arrangement 2013 Plenary Agreements Implementation: Commerce 
Control List, Definitions, and Reports; and Extension of Fly-by-Wire 
Technology and Software Controls; Final Rule

  Federal Register / Vol. 79 , No. 149 / Monday, August 4, 2014 / Rules 
and Regulations  

[[Page 45288]]


-----------------------------------------------------------------------

DEPARTMENT OF COMMERCE

Bureau of Industry and Security

15 CFR Parts 734, 738, 740, 743, 772, and 774

[Docket No. 131224999-3999-01]
RIN 0694-AG05


Wassenaar Arrangement 2013 Plenary Agreements Implementation: 
Commerce Control List, Definitions, and Reports; and Extension of Fly-
by-Wire Technology and Software Controls

AGENCY: Bureau of Industry and Security, Commerce.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The Bureau of Industry and Security (BIS) maintains, as part 
of its Export Administration Regulations (EAR), the Commerce Control 
List (CCL), which identifies certain of the items subject to Department 
of Commerce jurisdiction. This final rule revises the CCL to implement 
changes made to the Wassenaar Arrangement's List of Dual-Use Goods and 
Technologies (Wassenaar List) maintained and agreed to by governments 
participating in the Wassenaar Arrangement on Export Controls for 
Conventional Arms and Dual-Use Goods and Technologies (Wassenaar 
Arrangement, or WA) at the December 2013 WA Plenary Meeting (the 
Plenary). The Wassenaar Arrangement advocates implementation of 
effective export controls on strategic items with the objective of 
improving regional and international security and stability. This rule 
harmonizes the CCL with the changes made to the WA List at the Plenary 
by revising Export Control Classification Numbers (ECCNs) controlled 
for national security reasons in each category of the CCL, as well as 
amending the General Technology Note, WA reporting requirements, and 
definitions section in the EAR. However, BIS intends to publish a 
separate rule in September setting forth changes to the CCL resulting 
from the WA agreements for cybersecurity. These changes agreed to at 
the Plenary include raising the Adjusted Peak Performance (APP) for 
digital computers in ECCN 4A003. The President's report for High 
Performance Computers was sent to Congress on July 1, 2014 to set forth 
the new APP in accordance with the National Defense Authorization Act 
(NDAA) for FY1998. This rule also makes corresponding revisions to the 
de minimis rule, and post shipment verification reporting requirements 
in the Export Administration Regulations. This rule also extends the 
controls on specified fly-by-wire source code software and technology 
until June 20, 2015, as BIS continues to negotiate for multilateral 
controls for this software and technology. This rule also revises the 
license requirements for Mexico on the Commerce Country Chart, because 
of its recent membership in multiple multilateral export control 
regimes. In addition, this rule makes changes to the EAR resulting from 
previous rules issued as part of BIS's export control reform initiative 
and makes minor editorial corrections to the CCL.

DATES: This rule is effective August 4, 2014, except the amendments to 
parts 734, 743, and ECCN 4A003 (amendatory instructions: 2, 9, and 28), 
which are effective on August 30, 2014.

FOR FURTHER INFORMATION CONTACT: For general questions contact Sharron 
Cook, Office of Exporter Services, Bureau of Industry and Security, 
U.S. Department of Commerce at 202-482-2440 or by email: 
[email protected].
    For technical questions contact:

Categories 0, 1 & 2: Michael Rithmire at 202-482-6105
Category 3: Brian Baker at 202-482-5534
Categories 4 & 5: ITCD staff 202-482-0707
Category 6 (optics): Chris Costanzo at 202-482-0718
Category 6 (lasers): Mark Jaso at 202-482-0987
Category 6 (sensors and cameras): John Varesi 202-482-1114
Category 7: Jaymi Love 202-482-6581
Category 8: Darrell Spires 202-482-1954
Category 9: Daniel Squire 202-482-3710

SUPPLEMENTARY INFORMATION:

Background

    The Wassenaar Arrangement (WA) on Export Controls for Conventional 
Arms and Dual-Use Goods and Technologies is a group of 41 like-minded 
states committed to promoting responsibility and transparency in the 
global arms trade, and preventing destabilizing accumulations of arms. 
As a Participating State, the United States has committed to 
controlling for export all items on the WA control lists. The lists 
were first established in 1996 and have been revised annually 
thereafter. Proposals for changes to the WA control lists that achieve 
consensus are approved by Participating States at annual December 
Plenary meetings. Participating States are charged with implementing 
the agreed list changes as soon as possible after approval. 
Implementation of WA list changes ensures U.S. companies have a level 
playing field with their competitors in other WA member states.
    Unless otherwise indicated, the changes to the EAR described below 
are made in order to implement changes to the WA control lists approved 
at the December 2013 Plenary meeting.

Revisions to the Commerce Control List

Category 0--Nuclear Materials, Facilities, and Equipment [And 
Miscellaneous Items]

0A018 Items on the Wassenaar Munitions List
    In paragraph 0A018.b, the text that previously stated that an item 
is subject to the license authority of the U.S. Department of State, 
Directorate of Defense Trade Controls was universally changed to 
``subject to the ITAR'' in the Export Control Reform revisions (78 FR 
61874, October 4, 2013). Therefore the new language is inserted here.
    A Note is added to paragraph 0A018.b that states that 0A018.b does 
not apply to: ``components'' for ammunition crimped without a 
projectile (blank star); dummy ammunition with a pierced powder 
chamber; or other blank and dummy ammunition not incorporating 
components designed for live ammunition. These components do not pose a 
threat to national security and are now designated EAR99.

Category 1--Special Materials and Related Equipment, Chemicals, 
``Microorganisms,'' and ``Toxins''

1A004 (Protective and detection equipment and ``components,'' not 
``specially designed'' for military use)
    ECCN 1A004 is amended by adding Technical Notes after the Note 
following the introductory text to paragraph 1A004.a in the items 
paragraph of the List of Items Controlled section to clarify that 
filter canisters include filter cartridges.
1B001 (Equipment for the production or inspection of ``composite'' 
structures or laminates controlled by 1A002 or ``fibrous or filamentary 
materials'' controlled by 1C010 . . .)
    ECCN 1B001 is amended by revising the text of 1B001.b (`Tape-laying 
machines') and 1B001.g (`Tow-placement machines') to remove ambiguity 
with the current controls, which may result in a double coverage in 
controls or no control at all. A Technical Note is added to 1B001.b to 
explain the abilities of `tape-laying machines.' A Technical Note is 
added to 1B001.g to explain the abilities of `tow-placement machines.' 
The Technical Notes establish 25 mm as the break

[[Page 45289]]

point between tape-laying and tow-placement machines, with the intent 
to distinguish both the tape-laying and tow-placement machines from the 
filament winding machines specified in 1B001.a. In addition, the 
existing Technical Note regarding `primary servo positioning' axes 
control is now Technical Note 1 and a Technical Note 2 is added to 
define `filament band.'
1C008 (Non-fluorinated polymeric substances)
    ECCN 1C008 is amended by revising paragraphs a.3 and .f in the 
Items paragraph of the List of Items Controlled section to relax the 
controls on aromatic polyimides in 1C008.a.3 based on the foreign 
availability of this material. The current validation procedures are 
limited in accuracy to very small samples. Removal of these validation 
procedures and reference to national standards in the 1C008 Technical 
Notes provides a simpler and cleaner text. In order to accommodate the 
newly referenced testing method, Technical Note 1 is revised and a new 
Technical Note 2 is added to the existing 1C008 Technical Note. These 
changes do not affect the scope of the other paragraphs in 1C008.
1C010 (``Fibrous or filamentary materials'')
    ECCN 1C010 is amended by removing the Technical Note after 
paragraph b.2 and adding Technical Notes after the Note following 
paragraph c.2 in the Items paragraph of the List of Items Controlled 
section. These changes are made to remove ambiguity regarding the 
determination of the specific tensile strength and modulus that are 
specified in various 1C010 entries, especially when the 1C010 tensile 
properties metrics are applied to various forms of multi-axial 
materials (woven fabrics, random mats and braids).
    Also, a comma is added after the word ``pitch'' in paragraph e.2.a 
to correct the punctuation.
Annex to Category 1 ``List of Explosives''
    The List of Explosives is amended by revising paragraphs 32.d and 
43, removing and reserving paragraph 34 and adding paragraphs 44 
through 48. Paragraph 32 is amended by changing the square brackets to 
parentheses to read ``BDNTA ([bis-dinitrotriazole] amine); ((bis-
dinitrotriazole) amine);'' to be consistent with the International 
Union of Pure and Applied Chemistry (IUPAC) conventions. The deletion 
of paragraph 34 is a result of a class of energetics that has short-
term high temperature capability, which is no longer in demand. 
Paragraph 43 is amended by changing the semi-colon to a period at the 
end of the entry to accommodate the addition of paragraphs to follow. 
Paragraphs 44 through 48 are added to address the trend towards 
`Insensitive Munitions.' Insensitive munitions are chemically stable 
enough to withstand mechanical shock, fire, and impact by shrapnel, but 
can still explode as intended to destroy their targets.

Category 2--Materials Processing

``Technical Notes for 2B001 to 2B009, 2B201, 2B290 and 2B991 to 2B999''
    ``Technical Notes for 2B001 to 2B009, 2B201, 2B290 and 2B991 to 
2B999'' is amended by revising paragraph .f of the Note to paragraph 5 
in order to update the thresholds to ensure the rules regarding stated 
accuracy remain consistent in Category 2.
2B006 (Dimensional inspection or measuring systems, equipment, and 
``electronic assemblies'')
    ECCN 2B006 is amended by revising paragraphs b.1.b., b.1.c.2.b, and 
the introductory text of paragraph b.2 in the Items paragraph of the 
List of Items Controlled section. 2B006.b.1.b is revised to clarify the 
controls of certain displacement measuring instruments (Linear Variable 
Differential Transformer--LVDT). 2B006.b.2 is amended to delete the 
current definition for ``angular position deviation'' and to add the 
word ``accuracy'' in this entry. The definition refers to a standard 
that not only is out of date, but no longer published. WA decided that 
the definition of ``accuracy'' could be useful to clarify the 
assessment of accuracy of angular displacement measuring instruments 
for this entry.
2D002 (``Software'' for electronic devices, even when residing in an 
electronic device or system, enabling such devices or systems to 
function as a ``numerical control'' unit, capable of coordinating 
simultaneously more than 4 axes for ``contouring control''.)
    The term ``machine tools'' is replaced with ``items'' in Notes 1 
and 3 to clarify the scope of control on software for electronic 
devices or systems capable of controlling 5 or more axes.

Category 3--Electronics

3A001 (Electronic components and ``specially designed'' ``components'' 
therefor)
    ECCN 3A001 is amended by removing Notes 3 and 4 from the Related 
Control Notes paragraph in the List of Items Controlled section, 
because they refer to ECCN 3A982, which is removed by this rule.
    ECCN 3A001 is amended by revising Note 2 to paragraph 3A001.a, 
paragraphs a.5.a.1, a.7.b, b.2., b.3, and b.4; adding a Technical Note 
after the introductory text to paragraph 3A001.b; and revising Note 3 
to paragraph 3A001.h.
    ``Three dimensional integrated circuits'' are added to Note 2 to 
paragraph 3A001.a, because a new approach to improve the functionality 
and performance of integrated circuits is using a 3D integrated circuit 
(3D-IC).
    Paragraph 3A001.a.5.a.1 (High Performance Analog-to-Digital 
Integrated Circuits) is amended by replacing the output rate of 
``greater than 500 million words per second'' to ``greater than 1 
billion words per second'' to update the Analog-to-Digital Converter 
(ADC) control thresholds for the 8 and 9 bit resolution ADCs to reflect 
the advances in technology used in the commercial cellular 
communications and oscilloscope applications.
    Paragraph 3A001.a.7.b is amended by replacing ``or'' with ``of'' to 
make a correction submitted by a Technical Advisory Committee member.
    A Technical Note is added to 3A001.b to set forth alternative terms 
for ``peak saturated power output'' that may appear on product data 
sheets.
    This rule makes a series of changes regarding microwave or 
millimeter wave components specified by entries 3A001.b.2 (Microwave 
Monolithic Integrated Circuits--MMIC), 3A001.b.3 (Discrete microwave 
transistors) and 3A001.b.4 (Microwave solid state amplifiers). The 
changes are intended to add a frequency bandwidth (2.7-3.2 GHz) to each 
of the existing entries 3A001.b.2, b.3 and b.4. The changes also aim at 
modernizing the control text over the entire controlled spectrum by 
replacing the current control parameter `average power' with `peak 
saturated power.'
    A comma is added to Note 3 to paragraph 3A001.h to correct the 
punctuation. The addition of the comma makes the modifying phrase 
(incorporated into equipment designed for civil automobile, civil 
railway, or ``civil aircraft'' applications) apply to all three nouns 
(switches, diodes, and modules).
3A002 (General purpose electronic)
    ECCN 3A002 is amended by revising the Heading; revising License 
Exception GBS and CIV paragraphs; revising the introductory text to 
paragraph .a; removing and reserving paragraphs a.1 through a.4; 
revising paragraph a.6;

[[Page 45290]]

adding paragraph a.7; revising the introductory text to paragraph d.1.; 
and revising Technical Note 2 that appears after paragraph d.5.
    The Heading is amended by removing the phrase ``and accessories 
therefor.'' The only accessories enumerated in 3A002 are test tapes in 
3A002.a, which are test tapes for instruments described in 3A002.a.1 
through 3A002.a.4. As 3A002.a.1 through 3A002.a.4 are removed and 
reserved by this rule, the reference to ``accessories'' is no longer 
needed.
    Paragraphs 3A002.a.1 through a.4 are removed and reserved because 
magnetic instrumentation tape recorders are obsolete technology. The 
replacement technology is magnetic disk storage, for which instruments 
remain controlled in 3A002.a.6.
    Paragraph 3A002.a.6 (Digital instrumentation data recorders) is 
revised to address a potential loophole for digital instrumentation 
recorders that do not digitize data but rather receive digitized data 
from external digitizers.
    This rule adds new entry 3A002.a.7 to control very high-speed 
oscilloscopes that are used to develop and test military radars, 
communications systems, and electronic warfare systems. The values used 
in this new control are intended to separate the highest performing 
oscilloscopes from those used for more routine commercial applications. 
Consequential changes are also made in the introductory text to 3A002.a 
with the addition of `and oscilloscopes.'
    Paragraph 3A002.d.1 is amended by replacing ``pulses'' with 
``pulse-modulated signals'' to clarify that ``pulses'' more accurately 
refers to signals that are pulse modulated.
    Technical Note 2 that appears after paragraph 3A002.d.5 is amended 
to introduce the industrial norm of `pulse duration' and its 
measurement.
3A982, 3D982 and 3E982 (Microwave or millimeter wave components)
    ECCNs 3A982 and associated software (3D982) and technology (3E982) 
are removed from the Commerce Control List (CCL). These ECCNs are 
removed because the microwave and millimeter wave components identified 
in this entry were discussed and agreed for inclusion in the WA 2013 
Plenary updates to 3A001.b.2 and 3A001.b.3. Software ``specially 
designed'' for the development or production of equipment controlled by 
3A001.b is controlled under ECCN 3D001. Technology for the development 
or production of 3A001.b is controlled under ECCN 3E001. Because the 
items of concern are now controlled in these new entries, the need for 
ECCNs 3A982, 3D982 and 3E982 is eliminated.
3A991 (Electronic devices, and ``components'' not controlled by 3A001)
    ECCN 3A991 is amended by revising paragraph .d (field programmable 
logic devices) in the items paragraph of the List of Items Controlled 
section. The parameters are changed from ``gate count'' and ``toggle 
frequency'' to ``maximum number of single-ended digital input/
outputs.'' The control level is set at ``200 or greater and less than 
500.'' This is to align 3A991 parameters with 3A001.a.7.a parameters 
for these types of devices.
    3C005 (Silicon carbide (SiC), gallium nitride (GaN), aluminum 
nitride (AlN) . . .) is amended by adding ``semiconductor'' to the 
Heading to clarify the scope of this entry, because the goods that 
should be controlled by this entry are substrates of semiconductor 
materials, which are generally referred to as wafers.
3E002 (``Technology'' according to the General Technology Note other 
than that controlled in 3E001 for the ``development'' or ``production'' 
of a ``microprocessor microcircuit,'' ``micro-computer microcircuit'' 
and microcontroller microcircuit core, having an arithmetic logic unit 
with an access width of 32 bits or more and any of the following 
features or characteristics)
    ECCN 3E002.b is amended by replacing ``two 64-bit or larger 
floating-point operation results per cycle'' with ``four 64-bit or 
larger floating-point operation results per cycle'' to update the 
control text to maintain control of leading edge technology and 
decontrol that technology no longer considered state-of-the-art.

Category 4--Computers

ECCN 4A003 (``Digital computers,'' ``electronic assemblies'' and 
related equipment therefor)
    The AT license requirement paragraph is revised to update the 
Adjusted Peak Performance (APP) upper limit in the range in the cross 
reference to ECCN 4A994 from 3.0 Weighted TeraFLOPS (WT) to 8.0 WT to 
harmonize with the change to 4A003.b.
    The Congressional notification requirement set forth in subsections 
1211(d) and (e) of the National Defense Authorization Act (NDAA) for FY 
1998 (Pub. L. 105-85, November 18, 1997, 111 Stat. 1932) provide that 
the President must submit a report to Congress 60 days before adjusting 
the composite theoretical performance level above which exports of 
digital computers to Tier 3 countries require a license. The President 
sent a report to Congress on July 1, 2014 that establishes and provides 
justification for the 8.0 WT control level using the APP formula.
    The APP in the Note in the License Requirements section is changed 
from 3.0 WT to 8.0 WT to harmonize with the change to 4A003.b. This 
paragraph explains that no license is required for computers with an 
APP not exceeding 8.0 WT and for electronic assemblies described in 
4A003.c that are not capable of exceeding an APP exceeding 8.0 WT in 
aggregation, except to destinations in Country Group E:1 of Supplement 
No. 1 to part 740.
    The APP in 4A003.b for digital computers is raised from 3.0 WT to 
8.0 WT, because multi-core processor technology has continued to 
advance rapidly as feature size shrinks. Most high-performance computer 
systems use processors with four, eight, or more cores as the compute 
engine, and each core also has greater double-precision floating point 
capabilities.
4D001 (``Software'' for digital computers)
    List based License Exception TSR eligibility and License Exception 
STA conditions are amended by raising the APP from 0.5 WT to 1.0 WT to 
align with revision to 4D001 in the WA Sensitive List. The control 
parameter for software for digital computers is amended by raising the 
APP from 0.25 to 0.60 WT in paragraph 4D001.b.1, in order to maintain 
control on leading-edge software for the development or production of 
digital computers.
4E001 (``Technology'' for the development or production of digital 
computers)
    List based License Exception TSR eligibility and License Exception 
STA conditions are amended by raising the APP from 0.5 WT to 1.0 WT to 
align with revision to 4E001 in the WA Sensitive List. The control 
parameter for software for digital computers is amended by raising the 
APP from 0.25 to 0.60 WT in paragraph 4E001.b.1, in order to maintain 
control on leading-edge technology for the development or production of 
digital computers.

Category 5 Part 1--``Telecommunications''

5A001 (Telecommunications systems, equipment, ``components'' and 
``accessories'')
    A comma is added to 5A001.b.1.d to correct the punctuation and 
clarify the meaning of the sentence.

[[Page 45291]]

    In 5A001.b.5.b, the term ``frequency switching time'' is replaced 
by ``channel switching time'' and a Technical Note is added to define 
`channel switching time.' The definition for ``frequency switching 
time'' had been crafted for the purposes of defining a signal 
generator's characteristics more so than a radio receiver's. The change 
in term and definition will help clarify its interpretation for both 
signal generators specified under 3A002.d, as well as radio receivers 
specified by 5A001.b.5.
5E001 (``Technology'')
    ECCN 5E001.d is amended to align with the revisions made to ECCN 
3A001.b. The changes are intended to add a frequency bandwidth (2.7-3.2 
GHz) to 5E001.d. The changes also modernize the control text over the 
entire controlled spectrum in 5E001.d by replacing the current control 
parameter `average power' with `peak saturated power.'

Category 5 Part 2--``Information Security''

    Category 5 Part 2 is amended by revising paragraph b of Note 3. 
`Executable software' is added to Note 3, as well as a Technical Note 
to define `executable software' as `` ``software'' in executable form, 
from an existing hardware component excluded from 5A002 by the 
Cryptography Note.'' A Note is also added after the Technical Note that 
states, `` `Executable software' does not include complete binary 
images of the ``software'' running on an end-item.'' Encryption is 
increasingly a commonplace functionality implemented by `mass market' 
Information and Communications Technology (ICT) products. Moreover, 
cryptographic functionality is often implemented in ``software,'' with 
comparable capability found in hardware. This revision ensures that all 
such comparable components of `mass market' products are given equal 
treatment under the Cryptography Note.
    Category 5 Part 2 is amended by moving the Technical Note at the 
end of Note 4 to after 5A002.a.1.a. The Technical Note states, ``Parity 
bits are not included in the key length.'' so that it now immediately 
follows the text to which it refers. Within Category 5 Part 2, the 
topic of `parity bits' is only relevant to how key lengths are 
calculated and considered, and 5A002.a.1 is the only paragraph that 
involves key lengths.
5A002 (``Information security'' systems, equipment ``components'' 
therefor).
    An editorial correction is made to paragraph (i) of the 5A002 
decontrol note to remove ``or'' from the end of paragraph (i). ``Or'' 
is added to paragraph (j) of the 5A002 decontrol Note, because of the 
addition of paragraph (k). Paragraph (k) ``mobile telecommunications 
Radio Access Network (RAN) equipment designed for civil use . . .'' is 
added to the 5A002 decontrol Note. Domestic small cells for use in the 
home offer telecommunications service providers a way to roll out their 
networks without the need to install expensive infrastructure. Using 
their customer's Internet connections, they can backhaul data from 
their subscribers in the immediate vicinity of a small cell. These 
items are designed to be simple to install by anyone, and in many cases 
are mass market items. However, these items are not always marketed in 
a way that allows the application of Note 3 in Category 5 Part 2, 
because in some countries the sale of some small cells is restricted to 
privileged customers or high value individuals, and some have 
restrictions on where they may be used.
    This rule amends the Nota Bene after the introductory text of 
paragraph .a by adding the phrase, ``, and for related decryption 
``software'' and ``technology'' see 7D005 and 7E001.'' This is a 
consequential change to harmonize with the addition of ECCN 7D005 `` 
``Software'' specially designed to decrypt Global Navigation Satellite 
Systems (GNSS) ranging signals designed for government use'' and 
related technology in ECCN 7E001, and to ensure that GNSS-related 
software and technology resides in Cat 7 only and is not spread across 
two Categories, which may be undesirable and cause confusion.
    Paragraph 3 in the Technical Note to 5A001.a.1 is moved to the 
definition for ``cryptography'' in Sec.  772.1 of the EAR, because 
paragraph 3 applies directly and broadly to the definition of 
``cryptography.''
    The Note to 5A002.a.1 is removed because it is redundant. 5A002.a.1 
controls the implementation of ``cryptography'' utilizing `digital 
techniques' regardless of what types of `principles' (i.e., whether 
`analog' or otherwise) these `digital techniques' are based on.
    The introductory text to paragraph a.9 is amended by adding the 
phrase ``or perform'' to clarify the scope of the control. The whole 
text reads, ``Designed or modified to use or perform `quantum 
cryptography.'''

Category 6--Sensors and Lasers

6A001 (Acoustic systems, equipment and components)
    Note 3 is added to the introductory paragraph a.1.c, in order to 
clarify that 6A001.a.1.c applies to projectors or transducers designed 
and manufactured using either of two high performance transduction 
materials: 1) lead-magnesium-niobate/lead-titanate (Pb(Mg1/3Nb2/3)O3-
PbTiO3, or PMN-PT), or 2) lead-indium-niobate/lead-magnesium-niobate/
lead-titanate (Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3, PIN-PMN-PT). 
These materials are currently being used in medical ultrasound 
applications, but are increasingly being used in high performance 
military and civil projectors and transducers.
    In the Technical Note below paragraph a.1.c.2, a single quotation 
mark is added to the beginning of the term `acoustic power density' to 
add the missing single quotation mark.
    Paragraph a.1.e (Active individual sonars, ``specially designed'' 
or modified to detect, locate and automatically classify swimmers or 
divers) is amended by adding the phrase ``and ``specially designed'' 
transmitting and receiving acoustic arrays therefor,'' in order to 
control critical components of such systems.
    Paragraph a.2.a.3.d (Lead-magnesium-niobate/lead-titanate (i.e., 
Pb(Mg1/3Nb2/3)O3-PbTiO3, or PMN-PT) piezoelectric single crystals grown 
from solid solution) and paragraph a.2.a.3.e (Lead-indium-niobate/lead-
magnesium niobate/lead-titanate (i.e., Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/
3)O3-PbTiO3, or PIN-PMN-PT) piezoelectric single crystals grown from 
solid solution) are added as parameters for hydrophone sensing 
elements, because PMN-PT and PIN-PMN-PT single crystals are a new 
generation of piezoelectric materials that exhibit superior 
piezoelectric properties over PZT ceramics. Hydrophones designed using 
PIN-PMN-PT have greater bandwidth and sensitivity, as well as lower 
self-noise.
    Paragraph a.2.b.8 (Accelerometer-based hydro-acoustic sensors 
specified by 6A001.a.2.g) is added as a parameter for towed acoustic 
hydrophone arrays because these sensors are useful for military 
applications.
    Paragraph a.2.e.3 (Incorporating accelerometer-based hydro-acoustic 
sensors specified by 6A001.a.2.g) is added as a parameter for bottom or 
bay-cable hydrophone arrays because these sensors are useful for 
military applications. Consequential editorial revisions are made to 
paragraphs a.2.e.1 (removing an ``or'') and a.2.e.2.b (adding

[[Page 45292]]

an ``or''), because of the addition of paragraph a.2.e.3.
    Paragraph a.2.g (Accelerometer-based hydro-acoustic sensors) is 
added under passive marine acoustic systems, equipment, and specially 
designed components therefor, because these sensors are useful for 
military applications. A Note is included to clarify that 6A001.a.2.g 
does not apply to particle velocity sensors or geophones. Two Technical 
Notes are added to inform the reader that accelerometer-based hydro-
acoustic sensors are also known as vector sensors, and to include a 
definition for the term `acceleration sensitivity,' which is used in 
the parameters for these sensors.
6A005 (``Lasers,'' ``components'' and optical equipment)
    In the NP License Requirement paragraph, the existing text is 
replaced with ``NP applies to ``lasers'' that exceed the parameters of 
6A205.'' The License Requirement Note pertaining to NP controls is 
removed.
    References to 6A005.b.6.c.2 and 6A005.b.6.c.2.b are changed to 
6A005.b.6.d.2 and 6A005.b.6.d.2.b in the License Exceptions GBS and CIV 
eligibility paragraphs. These are consequential changes due to the 
revisions in 6A005.b.6.
    References to 6A005.a.6.b.1 and 6A005.b.6 are added after the 
definition for `wall-plug efficiency' in the Related Definitions 
paragraph. The definition for `non-repetitive pulsed' is added to the 
Related Definitions paragraph with references to where the term is 
used: Note 2 of 6A005 and 6A005.d.6.
    Note 2 at the beginning of the Items paragraph is revised by adding 
single quotes to the term `non-repetitieve pulsed' and a Technical Note 
is added to Note 2 to define `non-repetitive pulsed' to improve the 
understanding of Note 2.
    The Technical Note that defines `non-repetitive pulsed' is moved 
from 6A005.d.6 to after Note 2, where it is first used in 6A005. The 
definition is also added to the Related Definitions paragraph, because 
it is used more than once in 6A005.
    Note 2 is added to 6A005.a.6.b to describe multiple transverse mode 
industrial ``lasers'' that are not controlled under 6A005.a.6.b. This 
Note includes a Technical Note to define `brightness.'
    The parameters in paragraph 6A005.b.4, b.5, and b.6 are revised to 
reset the control level below the level for which military utility can 
be achieved for lasers with pulse durations less than 1 picosecond. 
Consequential changes are made to distinguish or move paragraphs that 
pertain to lasers with pulse durations equal to or exceeding 1 
picosecond. Here is where they were located and where they move to: 
b.4.a to b.4.b.1; b.4.b to b.4.b.2; b.5.a to b.5.b; b.5.b to b.5.c; 
b.6.a to b.6.b; b.6.b to b.6.c; and b.6.c to b.6.d. Consequential 
changes within ECCN 6A005 include: correcting references to these 
paragraphs that have moved in the NP paragraph of the License 
Requirements section, License Requirement paragraphs: (b) and (f), and 
License Exceptions GBS and CIV eligibility paragraphs. Consequential 
changes outside of ECCN 6A005 include revising the Related Controls 
Note 3 in ECCN 6A205 and the Heading of ECCN 6E201 to correct 
references to these paragraphs that have moved.
6A007 (Gravity meters (gravimeters) and gravity gradiometers)
    Paragraph 6A007.a is amended by removing ``[mu]gal'' and adding in 
its place ``[mu]Gal'' to correct the scientific abbreviation for 
microgal (one millionth of a gal). The gal, sometimes called galileo, 
(symbol Gal) is a unit of acceleration used extensively in the science 
of gravimetry. The gal is defined as 1 centimeter per second squared (1 
cm/s\2\).
    Paragraphs b.1 and b.2 are amended by removing ``mgal'' and adding 
in its place ``mGal'' to correct the scientific abbreviation for 
milligal (one thousandth of a gal). The gal, sometimes called galileo, 
(symbol Gal) is a unit of acceleration used extensively in the science 
of gravimetry. The gal is defined as 1 centimeter per second squared (1 
cm/s\2\).
    A Technical Note is added to 6A007.b to define `time-to-steady-
state registration,' which is used in 6A007.b.2, to make the control 
text clearer and more effective.
6A008 (Radar systems, equipment and assemblies, having any of the 
following (see List of Items Controlled section), and ``specially 
designed'' ``components'' therefor)
    Paragraph 6A008.k.2 is amended by adding the adjective 
``compressed'' and by adding a Note to decontrol two dimensional 
`marine radar' or `vessel traffic service' radar from 6A008.k.2. Solid 
state devices, which apply ``pulse compression,'' are replacing 
magnetron devices as a component of marine radars and Vessel Traffic 
Safety (VTS) radars for safety navigation. This revision decontrols 
such radars for safety navigation incorporating solid state devices 
from 6A008.k.2.
    The Note to 6A008.l.1 is amended by revising the phase ``marine or 
harbor radar'' to read `marine radar,' as well as adding single quotes 
around the term `marine radar.'
    The Note following the paragraph l.4 is amended by revising the 
paragraph it applies to from 6A008.l.4 to 6A008.l, as well as changing 
the term ``marine traffic control'' to single quoted `vessel traffic 
services.'
    Technical Notes are added to the end of the Items paragraph of 
6A008 to define `marine radar' and `vessel traffic service.'
6A205 (``Lasers,'' ``laser'' amplifiers and oscillators, other than 
those controlled by 6A005) ECCN 6A205 is amended by removing the 
reference to ``6A005.b.6.b'' and adding in its place ``6A005.b.6.c'' in 
paragraph (3) of the Related Controls paragraph of the List of Items 
Controlled section, to harmonize with revisions to 6A005 in this rule.
6B007 (Equipment to produce, align and calibrate land-based gravity 
meters with a static accuracy of better than 0.1 mgal)
    The Heading is amended by replacing ``mgal'' with ``mGal'' to 
correct the scientific unit abbreviation for milligal (one thousandth 
of a gal). The gal, sometimes called galileo, (symbol Gal) is a unit of 
acceleration used extensively in the science of gravimetry. The gal is 
defined as 1 centimeter per second squared (1 cm/s\2\).
6D001 (Software specially designed for the development or production of 
equipment controlled by 6A004, 6A005, 6A008 or 6B008)
    This rule removes the Nuclear Proliferation (NP) license 
requirement paragraph from the License Requirements section of 6D001, 
because the Nuclear Suppliers Group (NSG) Annex does not list software 
controls for any of the equipment identified in the heading of 6D001.
6E201 (Technology for ``use'' of specified equipment in Category 6)
    The Heading of ECCN 6E201 is amended by revising references to 
6A005 to harmonize with revisions to the items paragraph of 6A005 and 
the NP controls of 6A005 in this rule. In order to determine NP 
controls on 6A005 commodities, you must analyze 6A205 to determine if 
the commodities meet or exceed the parameters of commodities in 6A205. 
If the 6A005 commodities meet or exceed the parameters of 6A205 
commodities, then the 6A005 commodity is NP controlled. If the 6A005 
commodity is NP controlled, then the ``use'' technology for it is 
classified in 6E201.

[[Page 45293]]

Category 7--Navigation and Avionics

7A002 (Gyros or angular rate sensors, having any of the following (see 
List of Items Controlled section) and ``specially designed'' 
``components'' therefor)
    The Note to 7A002.a.1.b in the Items paragraph is amended by 
replacing the single quotes with double quotes around the term 
``spinning mass gyros,'' as the Technical Note below this Note that 
defined this term is deleted and the term is now defined in Sec.  772.1 
of the EAR. Terms used in multiple locations are generally not locally 
defined and indicated by single quotes, but are defined in Sec.  772.1 
of the EAR and are indicated with double quotes.
    Paragraph 7A002.a.2.a is amended by revising the ``bias'' 
``stability'' from ``less (better) than 40 degrees per hour'' to ``less 
(better) than 4 degrees per hour.'' Paragraph 7A002.a.2.b is amended by 
revising the ``angle random walk'' from ``less (better) than or equal 
to 0.2 degree per square root hour'' to ``less (better) than or equal 
to 0.1 degree per square root hour.'' These changes are made in 
consideration of commercial and technological development in the area 
of Micro-Electro-Mechanical Systems (MEMS). The Note to 7A002.a.2.b is 
amended by replacing the single quotes with double quotes around the 
term ``spinning mass gyros.''
7A003 (`Inertial measurement equipment or systems')
    The Heading is amended by using a more general phrase, `inertial 
measurement equipment or systems' instead of `inertial systems' to 
encompass the breadth of controlled products. The Heading establishes a 
``having any of the following'' structure regarding the functionalities 
that follow, which is intended to better accommodate multiple-output 
equipment. This new text is not intended to change the scope of the 
entry, but to better specify the inertial equipment to facilitate 
easier evaluation by licensing officers.
    ``Specially designed components'' no longer appear in the Heading 
or in the List of Items Controlled section. ``Specially designed 
components'' that should be controlled are specified in 7A001 
(Accelerometers) and 7A002 (Gyros).
    The definition for the term ``Data-Based Referenced Navigation'' 
(``DBRN'') Systems is removed from the Related Definitions paragraph, 
because this definition is moved to Sec.  772.1. Defined terms that are 
used in multiple ECCNs are placed in Sec.  772.1 and this term is used 
in 7A003, 7D003 and 7E004.
    A new note (Note 1) has been added at the beginning of the Items 
paragraph in order to help readers better understand the scope of the 
entry. In addition to describing the basic functionality of these 
products, the new note also provides a list of the most commonly used 
product names.
    A Technical Note below 7A003.a explains how to assess the 
performance depending on the application that is typical for that 
system (air, land and sea platforms). There are different controls for 
different types of products and the Technical Note provides 
instructions on how to apply these controls, i.e., 7A003.a.1, 7A003.a.2 
and 7A003.a.3 typically apply to `inertial measurement equipment or 
systems' designed for ``aircraft,'' vehicles, and vessels, 
respectively. Even though there is now a control specifically for 
navigation equipment for land vehicles, it is important to note that 
the control limit applied is not intended to control civilian car 
navigation equipment.
    Space qualified systems are now specified in 7A003.d because these 
are systems and not components specified by 7A002. Note the reference 
to ``spacecraft'' is removed from the current text of 7A003.a, because 
inertial equipment for ``spacecraft'' does not provide position.
7D003 (Other ``software,'' as specified)
    7D003.c (``Source code'' for integrated avionics or mission systems 
which combine sensor data and employ ``expert systems'') is removed and 
reserved, because no mission management systems employing ``expert 
systems'' could be identified. The definition for ``expert systems'' is 
also removed from Sec.  772.1 as a consequential change. The reference 
to 7D003.c is removed from the STA paragraph in the Special Conditions 
for STA section as well.
7D004 (``Source code'' incorporating ``development'' ``technology'' 
specified by 7E004.a.1 to a.6 or 7E004.b.)
    The Heading for 7D004 is amended by revising the reference to 
``7E004.a'' to read ``7E004.a.1 to a.6'' to specify only the technology 
relevant to flight control source code in 7D004.
7D005 (``Software'' ``specially designed'' to decrypt Global Navigation 
Satellite Systems (GNSS) ranging signals designed for government use)
    ECCN 7D005 is added to close a loophole in the controls which are 
associated with the control of receivers for Global Navigation 
Satellite Systems (GNSS); there is no entry which explicitly includes 
the software which performs the data processing of the relevant 
signals. It also takes into account the fact that GNSS receivers making 
use of encrypted signals do not actually contain the decrypt algorithms 
and software. The new entry will capture the software of concern 
irrespective of whether it is intended to reside in a receiver or 
elsewhere, for example a secure server. This software is controlled for 
NS:1 and AT:1 reasons and will require a license to all destinations, 
except Canada. No list-based license exceptions are available for this 
ECCN; however, License Exception STA may be available, as well as 
transaction based license exceptions as outlined in Part 740 of the 
EAR.
7E001 (``Technology'' according to the General Technology Note for the 
``development'' of equipment or ``software,'' specified by 7.A., 7.B., 
7D001., 7D002., or 7D003, or 7D005)
    ECCN 7D005 is added to the Heading and the NS license requirement 
paragraph of 7E001 to control ``development'' ``software'' specified in 
7D005 to close a loophole in the controls which are associated with the 
control of receivers for Global Navigation Satellite Systems (GNSS). 
This technology is controlled under NS:1 and AT:1 to all destinations, 
except Canada. No list-based license exceptions or License Exception 
STA are available for this ECCN. A Note is added to clarify that 7E001 
includes key management ``technology'' exclusively for equipment 
specified in 7A005.a to capture development technology used to produce 
potentially controlled software, including the development of 
decryption algorithms.
7E004 (Other ``technology'' as specified)
    ECCN 7E004 is amended by removing and reserving paragraph b.6 (Full 
authority digital flight control or multisensory mission management 
system, employing ``expert systems'') and removing the Nota Bene below 
it, because no such system could be identified.

Category 8--Marine

8A002 (Marine systems, equipment, ``parts'' and ``components,'')
    Paragraph 8A002.i.2 in the Items paragraph of the List of Items 
Controlled section is amended by deleting the phrase ``or by using a 
dedicated computer,'' because it has been found that remotely 
controlled articulated manipulators specially designed or modified for 
use with submersible

[[Page 45294]]

vehicles do not use a control method by a dedicated computer anymore, 
with the development of new technology.
    The Technical Note below 8A002.i.2 is amended by adding the phrase 
``related motion'' to clarify the control and by removing the phrase 
``or by using a dedicated computer'' for reasons stated in the previous 
paragraph.
    A Nota Bene is added below the Note that follows paragraph q.2 to 
reference 8A620.f for equipment and devices ``specially designed'' for 
military use.

Category 9--Aerospace and Propulsion

9A001 (Aero gas turbine engines)
    The Note to 9A001.a is revised to be Note 1, in order to add Note 
2.
    Note 2 is added following 9A001.a to state that ``9A001.a does not 
apply to aero gas turbine engines for Auxiliary Power Units (APUs) 
approved by the civil aviation authority in a Wassenaar Arrangement 
Participating State, see Supplement No. 1 to part 743 of the EAR.''

Supplement No. 2 to Part 774 ``General Technology and Software Notes''

    Supplement No. 2 to part 774 ``General Technology and Software 
Notes'' is amended by removing the phrase ``operation, maintenance 
(checking), and repair'' and adding in its place ``operation, 
maintenance (checking), or repair'' in the General Technology Note. 
This change is made to clarify that technology meeting any one of the 
aspects listed is controlled and does not have to meet all of the 
aspects to be controlled.

Supplement No. 5 to Part 774 ``Items Classified Under ECCNS 0A521, 
0B521, 0C521, 0D521 and 0E521''

    Supplement No. 5 to part 774 ``Items Classified Under ECCNS 0A521, 
0B521, 0C521, 0D521 and 0E521'' is amended by extending the expiration 
date to June 20, 2015 for 0D521 No. 2 and 0E521 No. 6, which is 
``source code'' for the ``development'' of fly-by-wire control systems 
and specified ``technology'' for fly-by-wire control systems. The 
extension is justified because Wassenaar proposals are being negotiated 
to add this source code and technology to the WA List.

Supplement No. 6 to Part 774 ``Sensitive List''

    Paragraphs (4)(ii) 4D001and (4)(iii) 4E001 are amended by revising 
the APP from 0.5 Weighted TeraFLOPS (WT) to 1.0 WT.
    Paragraph (7)(iv) 7D003.c is removed and reserved to harmonize with 
the removal of this paragraph from the CCL.
    This rule redesignates paragraphs (7)(v) and (7)(vi) to read 
(7)(vi) and (7)(vii), and adds new paragraph (7)(v) ``7D004.a to .d and 
.g'' to correct the oversight of dropping the Sensitive List entry when 
this software moved from 7D003 to 7D004.
Sec. 734.4 ``De minimis US Content''
    Previously, foreign-made computers with an APP of 3.0 WT located in 
a foreign country are not eligible for the application of the de 
minimis rules when they contain U.S.-origin controlled semiconductors 
(other than memory circuits) classified under ECCN 3A001 and are 
destined to a country in Computer Tier 3 of Section 740.7 of the EAR. 
This rule increases the APP parameter from 3.0 WT to 8.0 WT in Sec.  
734.4(a) to harmonize with the revision made to ECCN 4A003.

Supplement No. 1 to Part 738 ``Commerce Country Chart''

    Mexico was added as a Wassenaar Participating State in 2011. It was 
added as an Australia Group member in 2013. In 2013, it was also added 
to the Nuclear Suppliers Group. Therefore, BIS has decided to remove 
the ``X'' for Mexico under columns NS:2 and RS:2.
Sec. 740.13 License Exception TSU
    Section 740.13 is amended by replacing the phrase ``operation, 
maintenance (checking), and repair'' with ``operation, maintenance 
(checking), or repair'' in the second sentence of paragraph (a)(1). The 
same change was made to the General Software Note of the Wassenaar 
List, which is the Note License Exception TSU is based upon. Instead of 
meeting all of four of the listed characteristics (installation, 
operation, maintenance (checking), and repair), now the technology 
would only have to meet one of the four characteristics to be 
considered ``operation technology.''
Sec. 740.20 License Exception STA
    This rule removes and reserves paragraph (b)(2)(ix) that restricted 
the use of License Exception STA for 3A982 (Microwave or millimeter 
wave components that operate at frequencies below those controlled by 
3A001). This change is being made because ECCN 3A982 is removed by this 
rule and because the microwave and millimeter wave components 
identified in that ECCN are now controlled under 3A001.b.2 and 
3A001.b.3.
Section 743.2 ``High Performance Computers: Post Shipment Verification 
Reporting''
    This section outlines special post-shipment reporting requirements 
for the export of certain computers to destinations in Computer Tier 3 
of License Exception APP (Section 740.7 of the EAR). The reporting 
requirement applies to high performance computers exported to a 
destination in Computer Tier 3, as well as to exports of commodities 
used to enhance computers previously exported or reexported to Computer 
Tier 3 destinations, where the ``APP is greater than 3.0 Weighted 
TeraFLOPS (WT). This rule increases that APP level from 3.0 WT to 8.0 
WT in accordance with the WA agreement to increase the APP in ECCN 
4A003.

Part 772 Definitions

    While the WA agreed to remove the definition for ``angular position 
deviation'' from the WA list definitions, BIS is not removing the term 
from Sec.  772.1 of the EAR, because this term is still used in 
2B206.b.2 and .c.
    The definition for ``cryptography'' is amended by adding the phrase 
```secret parameters' (e.g., crypto variables) and/or associated key 
management,'' as well as adding a Technical Note that defines `secret 
parameters.' The `secret parameter' phrase and Technical Note were 
agreed upon by WA in 2012, but were inadvertently missed in the 
drafting of the implementation rule. These additions occurred in the 
context of establishing preventative measures for reverse engineering 
that is occurring during analysis of failures in integrated circuits. 
Also, the Technical Note in 5A002.a that explains that ``cryptography'' 
does not include ``fixed'' data compression or coding techniques 
applies directly and broadly to the definition of ``cryptography.'' 
Accordingly, this Technical Note is moved into the definition of 
``cryptography.''
    The definition for the term ``Data-Based Referenced Navigation'' 
(``DBRN'') Systems is removed from the Related Definitions paragraph of 
7A003 and added to Sec.  772.1, because defined terms that are used in 
multiple ECCNs are placed in Sec.  772.1. This term is used in 7A003, 
7D003 and 7E004.
    This rule removes the term ``expert systems'' from Sec.  772.1 of 
the EAR, because the control list paragraphs where it was used are 
deleted by this rule (7D003.c and 7E004.b.6). See explanations for 
removal of these paragraphs in the respective ECCN preambles above.

[[Page 45295]]

    The term ``frequency switching time'' in Sec.  772.1 of the EAR is 
amended by removing the phrase ``(Cat 3 and 5)'' and adding in its 
place ``(Cat 3),'' because in 5A001.b.5.b, the term ``frequency 
switching time'' is replaced by ``channel switching time.'' For more 
explanation, see the preamble for 5A001 above.
    The definition for ``measurement uncertainty'' used in Category 2 
is amended by removing one of the referenced standards ``VDI/VDE 
2617,'' because the VDI/VDE 2617 standard was withdrawn in mid-2005 and 
may not be purchased by the public. It is not appropriate to reference 
a standard in the control list definitions that is no longer published.
    The term ``space-qualified'' is amended by removing the phrase 
``Cat 3 and 6'' and adding in its place ``Cat 3, 6, and 7,'' because 
``space-qualified'' systems are now specified in 7A003.d.
    This rule adds the term ``spinning mass gyros'' in alphabetic order 
to Sec.  772.1 of the EAR. This term is used in decontrol Notes to 
7A002.a.1.b, a.2.b, and 7A003.d.2. Because it is used in multiple 
locations in the CCL, the Technical Notes that defined this term are 
removed and the definition is added to Sec.  772.1 of the EAR.
    This rule adds the term ``three dimensional integrated circuit'' in 
alphabetic order to Sec.  772.1 of the EAR. This term is added to Note 
2 to 3A001.a to clarify that the controls in 3A001 apply to these types 
of integrated circuits. 3D integrated circuit design is a recent 
approach to improving the functionality and performance of integrated 
circuits.

Export Administration Act

    Since August 21, 2001, the Export Administration Act of 1979, as 
amended, has been in lapse. However, the President, through Executive 
Order 13222 of August 17, 2001, 3 CFR, 2001 Comp., p. 783 (2002), as 
amended by Executive Order 13637 of March 8, 2013, 78 FR 16129 (March 
13, 2013), and as extended by the Notice of August 8, 2013, 78 FR 49107 
(August 12, 2013) has continued the EAR in effect under the 
International Emergency Economic Powers Act (50 U.S.C. 1701 et seq.). 
BIS continues to carry out the provisions of the Export Administration 
Act, as appropriate and to the extent permitted by law, pursuant to 
Executive Order 13222 as amended by Executive Order 13637.

Saving Clause

    Shipments of items removed from license exception eligibility or 
eligibility for export without a license as a result of this regulatory 
action that were on dock for loading, on lighter, laden aboard an 
exporting carrier, or en route aboard a carrier to a port of export, on 
August 4, 2014, pursuant to actual orders for export to a foreign 
destination, may proceed to that destination under the previous license 
exception eligibility or without a license so long as they have been 
exported from the United States before October 3, 2014. Any such items 
not actually exported before midnight, on October 3, 2014, require a 
license in accordance with this regulation.

Rulemaking Requirements

    1. Executive Orders 13563 and 12866 direct agencies to assess all 
costs and benefits of available regulatory alternatives and, if 
regulation is necessary, to select regulatory approaches that maximize 
net benefits (including potential economic, environmental, public 
health and safety effects, distributive impacts, and equity). Executive 
Order 13563 emphasizes the importance of quantifying both costs and 
benefits, of reducing costs, of harmonizing rules, and of promoting 
flexibility. This rule has been designated a ``significant regulatory 
action,'' under Executive Order 12866. Accordingly, the rule has been 
reviewed by the Office of Management and Budget.
    2. Notwithstanding any other provision of law, no person is 
required to respond to, nor shall any person be subject to a penalty 
for failure to comply with a collection of information subject to the 
requirements of the Paperwork Reduction Act of 1995 (44 U.S.C. 3501 et 
seq.) (PRA), unless that collection of information displays a currently 
valid Office of Management and Budget (OMB) Control Number. This rule 
involves two collections of information subject to the PRA. One of the 
collections has been approved by OMB under control number 0694-0088, 
``Multi-Purpose Application,'' and carries a burden hour estimate of 58 
minutes for a manual or electronic submission. The other of the 
collections has been approved by OMB under control number 0694-0106, 
``Reporting and Recordkeeping Requirements under the Wassenaar 
Arrangement,'' and carries a burden hour estimate of 21 minutes for a 
manual or electronic submission. Send comments regarding these burden 
estimates or any other aspect of these collections of information, 
including suggestions for reducing the burden, to OMB Desk Officer, New 
Executive Office Building, Washington, DC 20503; and to Jasmeet Seehra, 
OMB Desk Officer, by email at [email protected] or by fax 
to (202) 395-7285; and to the Office of Administration, Bureau of 
Industry and Security, Department of Commerce, 1401 Constitution Ave. 
NW., Room 6622, Washington, DC 20230.
    3. This rule does not contain policies with Federalism implications 
as that term is defined under Executive Order 13132.
    4. The provisions of the Administrative Procedure Act (5 U.S.C. 
553) requiring notice of proposed rulemaking, the opportunity for 
public participation, and a 30-day delay in effective date, are 
inapplicable because this regulation involves a military and foreign 
affairs function of the United States (5 U.S.C. 553(a)(1)). Immediate 
implementation of these amendments fulfills the United States' 
international obligation to the Wassenaar Arrangement on Export 
Controls for Conventional Arms and Dual-Use Goods and Technologies. The 
Wassenaar Arrangement contributes to international security and 
regional stability by promoting greater responsibility in transfers of 
conventional arms and dual use goods and technologies, thus preventing 
destabilizing accumulations of such items. The Wassenaar Arrangement 
consists of 41 member countries that act on a consensus basis and the 
changes set forth in this rule implement agreements reached at the 
December 2012 plenary session of the WA. Because the United States is a 
significant exporter of the items covered by this rule, implementation 
of this rule is necessary for the WA to achieve its purpose. Any delay 
in implementation will create a disruption in the movement of affected 
items globally because of disharmony between export control measures 
implemented by WA members, resulting in tension between member 
countries. Export controls work best when all countries implement the 
same export controls in a timely manner. If this rulemaking were 
delayed to allow for notice and comment and a 30-day delay in 
effectiveness, it would prevent the United States from fulfilling its 
commitment to the WA in a timely manner and would injure the 
credibility of the United States in this and other multilateral 
regimes.
    Further, no other law requires that a notice of proposed rulemaking 
and an opportunity for public comment be given for this final rule. 
Because a notice of proposed rulemaking and an opportunity for public 
comment are not required to be given for this rule under the 
Administrative Procedure Act or by any other law, the analytical 
requirements of the Regulatory Flexibility Act (5 U.S.C. 601 et seq.) 
are

[[Page 45296]]

not applicable. Therefore, this regulation is issued in final form. 
Although there is no formal comment period, public comments on this 
regulation are welcome on a continuing basis. Comments should be 
submitted to Sharron Cook, Office of Exporter Services, Bureau of 
Industry and Security, Department of Commerce, 14th and Pennsylvania 
Ave. NW., Room 2099, Washington, DC 20230.

List of Subjects

15 CFR Part 734

    Administrative practice and procedure, Exports, Inventions and 
patents, Research Science and technology.

15 CFR Parts 738 and 772

    Exports.

15 CFR Part 740

    Administrative practice and procedure, Exports, Reporting and 
recordkeeping requirements.

15 CFR Part 743

    Administrative practice and procedure, Reporting and recordkeeping 
requirements.

15 CFR Part 774

    Exports, Reporting and recordkeeping requirements.

    Accordingly, Parts 734, 738, 740, 743, 772 and 774 of the Export 
Administration Regulations (15 CFR Parts 730-774) are amended as 
follows:

PART 734 [AMENDED]

0
1. The authority citation for part 734 continues to read as follows:

    Authority: 50 U.S.C. app. 2401 et seq.; 50 U.S.C. 1701 et seq.; 
E.O. 12938, 59 FR 59099, 3 CFR, 1994 Comp., p. 950; E.O. 13020, 61 
FR 54079, 3 CFR, 1996 Comp., p. 219; E.O. 13026, 61 FR 58767, 3 CFR, 
1996 Comp., p. 228; E.O. 13222, 66 FR 44025, 3 CFR, 2001 Comp., p. 
783; E.O. 13637 of March 8, 2013, 78 FR 16129 (March 13, 2013); 
Notice of August 8, 2013, 78 FR 49107 (August 12, 2013); Notice of 
November 7, 2013, 78 FR 67289 (November 12, 2013).


Sec.  734.4  [Amended]

0
2. Section 734.4 is amended in paragraph (a)(1) by removing the phrase 
``3.0 Weighted TeraFLOPS (WT)'' and adding in its place ``8.0 Weighted 
TeraFLOPS (WT)''.

PART 738 [AMENDED]

0
3. The authority citation for part 738 continues to read as follows:

    Authority:  50 U.S.C. app. 2401 et seq.; 50 U.S.C. 1701 et seq.; 
10 U.S.C. 7420; 10 U.S.C. 7430(e); 22 U.S.C. 287c; 22 U.S.C. 3201 et 
seq.; 22 U.S.C. 6004; 30 U.S.C. 185(s), 185(u); 42 U.S.C. 2139a; 42 
U.S.C. 6212; 43 U.S.C. 1354; 15 U.S.C. 1824a; 50 U.S.C. app. 5; 22 
U.S.C. 7201 et seq.; 22 U.S.C. 7210; E.O. 13026, 61 FR 58767, 3 CFR, 
1996 Comp., p. 228; E.O. 13222, 66 FR 44025, 3 CFR, 2001 Comp., p. 
783; Notice of August 8, 2013, 78 FR 49107 (August 12, 2013).

Supplement No. 1 to Part 738 [Amended]

0
4. Supplement No. 1, the entry for Mexico is amended by removing the 
``X'' for columns NS:2 and RS:2.

PART 740 [AMENDED]

0
5. The authority citation for part 740 continues to read as follows:

    Authority:  50 U.S.C. app. 2401 et seq.; 50 U.S.C. 1701 et seq.; 
22 U.S.C. 7201 et seq.; E.O. 13026, 61 FR 58767, 3 CFR, 1996 Comp., 
p. 228; E.O. 13222, 66 FR 44025, 3 CFR, 2001 Comp., p. 783; Notice 
of August 8, 2013, 78 FR 49107 (August 12, 2013).


Sec.  740.13  [Amended]

0
6. Section 740.13 is amended in the second sentence in paragraph (a)(1) 
by removing the phrase ``operation, maintenance (checking), and 
repair'' and adding in its place ``operation, maintenance (checking), 
or repair''.


Sec.  740.20  [Amended]

0
7. Section 740.20 is amended by removing and reserving paragraph 
(b)(2)(ix).

PART 743 [AMENDED]

0
8. The authority citation for part 743 continues to read as follows:

    Authority:  50 U.S.C. app. 2401 et seq.; 50 U.S.C. 1701 et seq.; 
E.O. 13222, 66 FR 44025, 3 CFR, 2001 Comp., p. 783; E.O. 13637 of 
March 8, 2013, 78 FR 16129 (March 13, 2013); 78 FR 16129 ; Notice of 
August 8, 2013, 78 FR 49107 (August 12, 2013).


Sec.  743.2  [Amended]

0
9. Section 743.2 is amended in paragraph (b) by removing the phrase 
``3.0 Weighted TeraFLOPS (WT)'' and adding in its place ``8.0 Weighted 
TeraFLOPS (WT)''.

PART 772 [AMENDED]

0
10. The authority citation for part 772 continues to read as follows:

    Authority:  50 U.S.C. app. 2401 et seq.; 50 U.S.C. 1701 et seq.; 
E.O. 13222, 66 FR 44025, 3 CFR, 2001 Comp., p. 783; Notice of August 
12, 2011, 76 FR 50661 (August 16, 2011).


0
11. Section 772.1 is amended by:
0
a. Revising the term ``Cryptography'';
0
b. Adding the term ``Data-Based Referenced Navigation'' (``DBRN'') 
Systems'';
0
c. Removing the term ``Expert systems'';
0
d. Removing the phrase ``(Cat 3 and 5)'' and adding in its place ``(Cat 
3)'' in the term ``Frequency switching time.''; and
0
e. Revising the term ``Measurement uncertainty'';
0
f. Removing the phrase ``Cat 3 and 6'' and adding in its place ``Cat 3, 
6, and 7'' in the term ``Space-qualified''; and
0
g. Adding the terms ``Spinning mass gyros'' and ``Three dimensional 
integrated circuit'' in alphabetic order,.
    The additions and revisions read as follows:


Sec.  772.1  Definitions of terms as used in the Export Administration 
Regulations (EAR).

* * * * *
    Cryptography. (Cat 5) The discipline that embodies principles, 
means and methods for the transformation of data in order to hide its 
information content, prevent its undetected modification or prevent its 
unauthorized use. ``Cryptography'' is limited to the transformation of 
information using one or more `secret parameters' (e.g., crypto 
variables) and/or associated key management.

    Note:
     ``Cryptography'' does not include ``fixed'' data compression or 
coding techniques.


    Technical Note:
    `Secret parameter': a constant or key kept from the knowledge of 
others or shared only within a group.

* * * * *
    Data-Based Referenced Navigation (``DBRN'') Systems. (Cat 7) 
Systems which use various sources of previously measured geo-mapping 
data integrated to provide accurate navigation information under 
dynamic conditions. Data sources include bathymetric maps, stellar 
maps, gravity maps, magnetic maps or 3-D digital terrain maps.
* * * * *
    Measurement uncertainty. (Cat 2) The characteristic parameter that 
specifies in what range around the output value the correct value of 
the measurable variable lies with a confidence level of 95%. It 
includes the uncorrected systematic deviations, the uncorrected 
backlash, and the random deviations (Ref.: ISO 10360-2).
* * * * *
    Spinning mass gyros. (Cat 7) ``Spinning mass gyros'' are gyros 
which use a continually rotating mass to sense angular motion.
* * * * *
    Three dimensional integrated circuit. (Cat 3) A collection of 
semiconductor die, integrated together, and having vias passing 
completely through at least one

[[Page 45297]]

die to establish interconnections between die.
* * * * *

PART 774 [AMENDED]

0
12. The authority citation for part 774 continues to read as follows:

    Authority:  50 U.S.C. app. 2401 et seq.; 50 U.S.C. 1701 et seq.; 
10 U.S.C. 7420; 10 U.S.C. 7430(e); 22 U.S.C. 287c, 22 U.S.C. 3201 et 
seq.; 22 U.S.C. 6004; 30 U.S.C. 185(s), 185(u); 42 U.S.C. 2139a; 42 
U.S.C. 6212; 43 U.S.C. 1354; 15 U.S.C. 1824a; 50 U.S.C. app. 5; 22 
U.S.C. 7201 et seq.; 22 U.S.C. 7210; E.O. 13026, 61 FR 58767, 3 CFR, 
1996 Comp., p. 228; E.O. 13222, 66 FR 44025, 3 CFR, 2001 Comp., p. 
783; Notice of August 12, 2011, 76 FR 50661 (August 16, 2011).


0
13. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 0, ECCN 0A018 is amended by revising paragraph b., and adding 
a Note after paragraph b., of the items paragraph in the List of Items 
Controlled section to read as follows:

Supplement No. 1 to Part 774--The Commerce Control List

* * * * *

0A018 Items on the Wassenaar Munitions List (see List of Items 
Controlled).

* * * * *

List of Items Controlled

* * * * *
Items:
* * * * *
    b. ``Specially designed'' components and parts for ammunition, 
except cartridge cases, powder bags, bullets, jackets, cores, 
shells, projectiles, boosters, fuses and components, primers, and 
other detonating devices and ammunition belting and linking machines 
(all of which are ``subject to the ITAR.'' (See 22 CFR parts 120 
through 130);

    Note:
     0A018.b does not apply to ``components'' ``specially designed'' 
for blank or dummy ammunition as follows:
    a. Ammunition crimped without a projectile (blank star);
    b. Dummy ammunition with a pierced powder chamber;
    c. Other blank and dummy ammunition, not incorporating 
components designed for live ammunition.

* * * * *


0
14. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 1, ECCN 1A004 is amended by removing the Technical Note after 
the Note following the introductory text to paragraph a. of the items 
paragraph in the List of Items Controlled section and adding in its 
place the Technical Notes to read as follows:

1A004 Protective and detection equipment and ``components,'' not 
``specially designed'' for military use, as follows (see List of Items 
Controlled).

* * * * *

List of Items Controlled

* * * * *
Items:

    a. * * *

    Technical Notes:
     For the purpose of 1A004.a:
    1. Full face masks are also known as gas masks.
    2. Filter canisters include filter cartridges.

* * * * *


0
15. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 1, ECCN 1B001 is amended by revising paragraphs b. and g., and 
adding Technical Notes after both paragraphs b. and g., in the items 
paragraph of the List of Items Controlled section to read as follows:

1B001 Equipment for the production or inspection of ``composite'' 
structures or laminates controlled by 1A002 or ``fibrous or filamentary 
materials'' controlled by 1C010, as follows (see List of Items 
Controlled), and ``specially designed'' ``components'' and 
``accessories'' therefor.

* * * * *

List of Items Controlled

* * * * *
Items:
* * * * *
    b. `Tape laying machines', of which the motions for positioning 
and laying tape are coordinated and programmed in five or more 
`primary servo positioning' axes, ``specially designed'' for the 
manufacture of ``composite'' airframe or missile structures;

    Technical Note:
     For the purposes of 1B001.b, `tape-laying machines' have the 
ability to lay one or more `filament bands' limited to widths 
greater than 25 mm and less than or equal to 305 mm, and to cut and 
restart individual `filament band' courses during the laying 
process.

* * * * *
    g. Tow-placement machines, of which the motions for positioning 
and laying tows are coordinated and programmed in two or more 
`primary servo positioning' axes, ``specially designed'' for the 
manufacture of ``composite'' airframe or missile structures.

    Technical Note to 1B001.g:
     For the purposes of 1B001.g, `tow-placement machines' have the 
ability to place one or more `filament bands' having widths less 
than or equal to 25 mm, and to cut and restart individual `filament 
band' courses during the placement process.

Technical Notes for 1B001:

    1. For the purpose of 1B001, `primary servo positioning' axes 
control, under computer program direction, the position of the end 
effector (i.e., head) in space relative to the work piece at the 
correct orientation and direction to achieve the desired process.
    2. For the purposes of 1B001, a `filament band' is a single 
continuous width of fully or partially resin-impregnated tape, tow 
or fiber.


0
16. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 1, ECCN 1C008 is amended by revising paragraphs a.3. and f., 
and removing the Technical Note and adding two Technical Notes in its 
place, in the Items paragraph of the List of Items Controlled section 
to read as follows:

1C008 Non-fluorinated polymeric substances as follows (see List of 
Items Controlled).

* * * * *

List of Items Controlled

* * * * *
Items:

    a. * * *
    a.3. Aromatic polyimides having a `glass transition temperature 
(Tg)' exceeding 505 K (232[deg] C);
* * * * *
    f. Polybiphenylenethersulphone having a `glass transition 
temperature (Tg)' exceeding 563 K (290[deg] C).

Technical Notes:

    1. The `glass transition temperature (Tg)' for 1C008.a.2 
thermoplastic materials and 1C008.a.4 materials is determined using 
the method described in ISO 11357-2 (1999) or national equivalents
    2. The `glass transition temperature (Tg)' for 1C008.a.2 
thermosetting materials and 1C008.a.3 materials is determined using 
the 3-point bend method described in ASTM D 7028-07 or equivalent 
national standard. The test is to be performed using a dry test 
specimen which has attained a minimum of 90% degree of cure as 
specified by ASTM E 2160-04 or equivalent national standard, and was 
cured using the combination of standard- and post-cure processes 
that yield the highest Tg.


0
17. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 1, ECCN 1C010 is amended by:
0
a. Removing the Technical Note after the Note in paragraph b.2 in the 
Items paragraph of the List of Items Controlled section;
0
b. Adding Technical Notes after the Note following paragraph c.2. in 
the Items paragraph of the List of Items Controlled section; and
0
c. Adding a comma after the word ``pitch'' in paragraph e.2.a.
    The additions read as follows:

1C010 ``Fibrous or filamentary materials'' as follows (see List of 
Items Controlled).

* * * * *

List of Items Controlled

* * * * *
Items:
* * * * *
    c. * * *
    c.2. * * *


[[Page 45298]]


    Note:
    * * *

Technical Notes:

    1. For the purpose of calculating ``specific tensile strength'', 
``specific modulus'' or specific weight of ``fibrous or filamentary 
materials'' in 1C010.a, 1C010.b or 1C010.c, the tensile strength and 
modulus should be determined by using Method A described in ISO 
10618 (2004) or national equivalents.
    2. Assessing the ``specific tensile strength'', ``specific 
modulus'' or specific weight of non-unidirectional ``fibrous or 
filamentary materials'' (e.g., fabrics, random mats or braids) in 
1C010 is to be based on the mechanical properties of the constituent 
unidirectional monofilaments (e.g., monofilaments, yarns, rovings or 
tows) prior to processing into the non-unidirectional ``fibrous or 
filamentary materials''.
* * * * *

0
18. In Supplement No. 1 to part 774, Category 1, Annex to Category 1 
``List of Explosives'' is amended by:
0
a. Revising paragraphs 32.d and 43;
0
b. Removing and reserving paragraph 34; and
0
c. Adding paragraphs 44 through 48.
    The revisions and additions read as follows:

ANNEX to Category 1

List of Explosives (See ECCNs 1A004 and 1A008)

* * * * *
    32. * * *
    d. BDNTA ((bis dinitrotriazole)amine);
* * * * *
    43. Nitroguanidine (NQ) (CAS 556-88-7);
    44. DNAN (2,4-dinitroanisole) (CAS 119-27-7);
    45. TEX (4,10-Dinitro-2,6,8,12-tetraoxa-4,10-
diazaisowurtzitane);
    46. GUDN (Guanylurea dinitramide) FOX-12 (CAS 217464-38-5);
    47. Tetrazines as follows:
    a. BTAT (Bis(2,2,2-trinitroethyl)-3,6-diaminotetrazine);
    b. LAX-112 (3,6-diamino-1,2,4,5-tetrazine-1,4-dioxide);
    48. Energetic ionic materials melting between 343 K (70[deg] C) 
and 373 K (100[deg] C) and with detonation velocity exceeding 6,800 
m/s or detonation pressure exceeding 18 GPa (180 kbar).


0
19. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 2, Product Group B, ``Technical Notes for 2B001 to 2B009, 
2B201, 2B290 and 2B991 to 2B999'' is amended by revising paragraph f. 
of the Note to paragraph 5, to read as follows:

B. TEST, INSPECTION AND ``PRODUCTION EQUIPMENT''

Technical Notes for 2B001 to 2B009, 2B201, 2B290 and 2B991 to 2B999:

* * * * *

    5. * * *

    Note to paragraph 5:
    * * *


    f. If any axis of a machine model not controlled by 2B001.a. to 
2B001.c. has a stated accuracy [Amacr] equal to or less than the 
specified positioning accuracy of each machine tool model plus 2 
[micro]m, the builder should be required to reaffirm the accuracy 
level once every eighteen months.
* * * * *


0
20. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 2, ECCN 2B006 is amended by revising paragraphs b.1.b. through 
b.1.b.2., b.1.c.2.b., and the introductory text of paragraph b.2., and 
by adding a Technical Note after b.1.b.2. in the Items paragraph of the 
List of Items Controlled section to read as follows:

2B006 Dimensional inspection or measuring systems, equipment, and 
``electronic assemblies'', as follows (see List of Items Controlled).

* * * * *

List of Items Controlled

* * * * *
Items:
* * * * *
    b. * * *
    b.1. * * *
    b.1.b. Linear Variable Differential Transformer (LVDT) systems 
having all of the following:
    b.1.b.1. ``''Having any of the following:
    b.1.b.1.a. ``Linearity'' equal to or less (better) than 0.1% 
measured from 0 to the `full operating range', for LVDTs with a 
`full operating range' up to and including  5 mm; or
    b.1.b.1.b. ``Linearity'' equal to or less (better) than 0.1% 
measured from 0 to 5 mm for LVDTs with a `full operating range' 
greater than  5 mm; and
    b.1.b.2. Drift equal to or less (better) than 0.1% per day at a 
standard ambient test room temperature  1 K;

    Technical Note:
    For the purposes of 2B006.b.1.b, `full operating range' is half 
of the total possible linear displacement of the LVDT. For example, 
LVDTs with a `full operating range' up to and including  5 mm can measure a total possible linear 
displacement of 10 mm.


    b.1.c. * * *
    b.1.c.2. * * *
    b.1.c.2.b. Capable of achieving a ``measurement uncertainty'' 
equal to or less (better) than (0.2 + L/2,000) [mu]m (L is the 
measured length in mm) at any point within a measuring range, when 
compensated for the refractive index of air; or
* * * * *
    b.2. Angular displacement measuring instruments having an 
angular position ``accuracy'' equal to or less (better) than 
0.00025[deg];
* * * * *


0
21. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 2, ECCN 2D002 is amended by revising the items paragraph in 
the List of Items Controlled section to read as follows:

2D002 ``Software'' for electronic devices, even when residing in an 
electronic device or system, enabling such devices or systems to 
function as a ``numerical control'' unit, capable of coordinating 
simultaneously more than 4 axes for ``contouring control''.

* * * * *

List of Items Controlled

* * * * *
Items:

    Note 1:
     2D002 does not control ``software'' ``specially designed'' or 
modified for the operation of items not specified by Category 2.


    Note 2:
     2D002 does not control ``software'' for items specified by 
2B002. See 2D001 and 2D003 for ``software'' for items specified by 
2B002.


    Note 3:
     2D002 does not apply to ``software'' that is exported with, and 
the minimum necessary for the operation of, items not specified by 
Category 2.


    The list of items controlled is contained in the ECCN heading.


0
22. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 3, ECCN 3A001 is amended by:
0
a. Removing Related Control Notes (3) and (4) in the List of Items 
Controlled section;
0
b. Revising Note 2 to paragraph a. in the Items paragraph of the List 
of Items Controlled section;
0
c. Revising paragraphs a.5.a.1. and a.7.b. in the Items paragraph of 
the List of Items Controlled section;
0
d. Adding a Technical Note after the introductory text to paragraph b. 
in the Items paragraph of the List of Items Controlled section;
0
e. Revising paragraphs b.2., b.3., and b.4.; and
0
f. Revising Note 3 to paragraph h. in the Items paragraph of the List 
of Items Controlled section.
    The revisions and additions read as follows:

3A001 Electronic components and ``specially designed'' ``components'' 
therefor, as follows (see List of Items Controlled).

* * * * *

List of Items Controlled

* * * * *
Items:
    a. * * *

    Note 2:
     Integrated circuits include the following types:
    --Monolithic integrated circuits;
    --Hybrid integrated circuits;
    --Multichip integrated circuits;
    --Film type integrated circuits, including silicon-on-sapphire 
integrated circuits;
    --Optical integrated circuits;
    --``Three dimensional integrated circuits''.n

* * * * *
    a.5. * * *
    a.5.a. * * *

[[Page 45299]]

    a.5.a.1. A resolution of 8 bit or more, but less than 10 bit, 
with an output rate greater than 1 billion words per second;
* * * * *
    a.7. * * *
    a.7.b. An `aggregate one-way peak serial transceiver data rate' 
of 200 Gb/s or greater;
* * * * *
    b. * * *

    Technical Note:
     For purposes of 3A001.b, the parameter peak saturated power 
output may also be referred to on product data sheets as output 
power, saturated power output, maximum power output, peak power 
output, or peak envelope power output.

* * * * *
    b.2. Microwave ``Monolithic Integrated Circuits'' (MMIC) power 
amplifiers that are any of the following:
    b.2.a. Rated for operation at frequencies exceeding 2.7 GHz up 
to and including 6.8 GHz with a ``fractional bandwidth'' greater 
than 15%, and having any of the following:
    b.2.a.1. A peak saturated power output greater than 75 W (48.75 
dBm) at any frequency exceeding 2.7 GHz up to and including 2.9 GHz;
    b.2.a.2. A peak saturated power output greater than 55 W (47.4 
dBm) at any frequency exceeding 2.9 GHz up to and including 3.2 GHz;
    b.2.a.3. A peak saturated power output greater than 40 W (46 
dBm) at any frequency exceeding 3.2 GHz up to and including 3.7 GHz; 
or
    b.2.a.4. A peak saturated power output greater than 20 W (43 
dBm) at any frequency exceeding 3.7 GHz up to and including 6.8 GHz;
    b.2.b. Rated for operation at frequencies exceeding 6.8 GHz up 
to and including 16 GHz with a ``fractional bandwidth'' greater than 
10%, and having any of the following:
    b.2.b.1. A peak saturated power output greater than 10 W (40 
dBm) at any frequency exceeding 6.8 GHz up to and including 8.5 GHz; 
or
    b.2.b.2. A peak saturated power output greater than 5 W (37 dBm) 
at any frequency exceeding 8.5 GHz up to and including 16 GHz;
    b.2.c. Rated for operation with a peak saturated power output 
greater than 3 W (34.77 dBm) at any frequency exceeding 16 GHz up to 
and including 31.8 GHz, and with a ``fractional bandwidth'' of 
greater than 10%;
    b.2.d. Rated for operation with a peak saturated power output 
greater than 0.1n W (-70 dBm) at any frequency exceeding 31.8 GHz up 
to and including 37 GHz;
    b.2.e. Rated for operation with a peak saturated power output 
greater than 1 W (30 dBm) at any frequency exceeding 37 GHz up to 
and including 43.5 GHz, and with a ``fractional bandwidth'' of 
greater than 10%;
    b.2.f. Rated for operation with a peak saturated power output 
greater than 31.62 mW (15 dBm) at any frequency exceeding 43.5 GHz 
up to and including 75 GHz, and with a ``fractional bandwidth'' of 
greater than 10%;
    b.2.g. Rated for operation with a peak saturated power output 
greater than 10 mW (10 dBm) at any frequency exceeding 75 GHz up to 
and including 90 GHz, and with a ``fractional bandwidth'' of greater 
than 5%; or
    b.2.h. Rated for operation with a peak saturated power output 
greater than 0.1 nW (-70 dBm) at any frequency exceeding 90 GHz;

    Note 1:
     [RESERVED]


    Note 2:
    The control status of the MMIC whose rated operating frequency 
includes frequencies listed in more than one frequency range, as 
defined by 3A001.b.2.a through 3A001.b.2.h, is determined by the 
lowest peak saturated power output control threshold.


    Note 3:
     Notes 1 and 2 following the Category 3 heading for product 
group A. Systems, Equipment, and Components mean that 3A001.b.2 does 
not control MMICs if they are ``specially designed'' for other 
applications, e.g., telecommunications, radar, automobiles.

    b.3. Discrete microwave transistors that are any of the 
following:
    b.3.a. Rated for operation at frequencies exceeding 2.7 GHz up 
to and including 6.8 GHz and having any of the following:
    b.3.a.1. A peak saturated power output greater than 400 W (56 
dBm) at any frequency exceeding 2.7 GHz up to and including 2.9 GHz;
    b.3.a.2. A peak saturated power output greater than 205 W (53.12 
dBm) at any frequency exceeding 2.9 GHz up to and including 3.2 GHz;
    b.3.a.3. A peak saturated power output greater than 115 W (50.61 
dBm) at any frequency exceeding 3.2 GHz up to and including 3.7 GHz; 
or
    b.3.a.4. A peak saturated power output greater than 60 W (47.78 
dBm) at any frequency exceeding 3.7 GHz up to and including 6.8 GHz;
    b.3.b. Rated for operation at frequencies exceeding 6.8 GHz up 
to and including 31.8 GHz and having any of the following:
    b.3.b.1. A peak saturated power output greater than 50 W (47 
dBm) at any frequency exceeding 6.8 GHz up to and including 8.5 GHz;
    b.3.b.2. A peak saturated power output greater than 15 W (41.76 
dBm) at any frequency exceeding 8.5 GHz up to and including 12 GHz;
    b.3.b.3. A peak saturated power output greater than 40 W (46 
dBm) at any frequency exceeding 12 GHz up to and including 16 GHz; 
or
    b.3.b.4. A peak saturated power output greater than 7 W (38.45 
dBm) at any frequency exceeding 16 GHz up to and including 31.8 GHz;
    b.3.c. Rated for operation with a peak saturated power output 
greater than 0.5 W (27 dBm) at any frequency exceeding 31.8 GHz up 
to and including 37 GHz;
    b.3.d. Rated for operation with a peak saturated power output 
greater than 1 W (30 dBm) at any frequency exceeding 37 GHz up to 
and including 43.5 GHz; or
    b.3.e. Rated for operation with a peak saturated power output 
greater than 0.1 nW (-70 dBm) at any frequency exceeding 43.5 GHz;

    Note 1:
     The control status of a transistor, whose rated operating 
frequency includes frequencies listed in more than one frequency 
range, as defined by 3A001.b.3.a through 3A001.b.3.e, is determined 
by the lowest peak saturated power output control threshold.


    Note 2:
     3A001.b.3 includes bare dice, dice mounted on carriers, or dice 
mounted in packages. Some discrete transistors may also be referred 
to as power amplifiers, but the status of these discrete transistors 
is determined by 3A001.b.3.

    b.4. Microwave solid state amplifiers and microwave assemblies/
modules containing microwave solid state amplifiers, that are any of 
the following:
    b.4.a. Rated for operation at frequencies exceeding 2.7 GHz up 
to and including 6.8 GHz with a ``fractional bandwidth'' greater 
than 15%, and having any of the following:
    b.4.a.1. A peak saturated power output greater than 500 W (57 
dBm) at any frequency exceeding 2.7 GHz up to and including 2.9 GHz;
    b.4.a.2. A peak saturated power output greater than 270 W (54.3 
dBm) at any frequency exceeding 2.9 GHz up to and including 3.2 GHz;
    b.4.a.3. A peak saturated power output greater than 200 W (53 
dBm) at any frequency exceeding 3.2 GHz up to and including 3.7 GHz; 
or
    b.4.a.4. A peak saturated power output greater than 90 W (49.54 
dBm) at any frequency exceeding 3.7 GHz up to and including 6.8 GHz;
    b.4.b. Rated for operation at frequencies exceeding 6.8 GHz up 
to and including 31.8 GHz with a ``fractional bandwidth'' greater 
than 10%, and having any of the following:
    b.4.b.1. A peak saturated power output greater than 70 W (48.54 
dBm) at any frequency exceeding 6.8 GHz up to and including 8.5 GHz;
    b.4.b.2. A peak saturated power output greater than 50 W (47 
dBm) at any frequency exceeding 8.5 GHz up to and including 12 GHz;
    b.4.b.3. A peak saturated power output greater than 30 W (44.77 
dBm) at any frequency exceeding 12 GHz up to and including 16 GHz; 
or
    b.4.b.4. A peak saturated power output greater than 20 W (43 
dBm) at any frequency exceeding 16 GHz up to and including 31.8 GHz;
    b.4.c. Rated for operation with a peak saturated power output 
greater than 0.5 W (27 dBm) at any frequency exceeding 31.8 GHz up 
to and including 37 GHz;
    b.4.d. Rated for operation with a peak saturated power output 
greater than 2 W (33 dBm) at any frequency exceeding 37 GHz up to 
and including 43.5 GHz, and with a ``fractional bandwidth'' of 
greater than 10%;
    b.4.e. Rated for operation at frequencies exceeding 43.5 GHz and 
having any of the following:
    b.4.e.1. A peak saturated power output greater than 0.2 W (23 
dBm) at any frequency exceeding 43.5 GHz up to and including 75 GHz, 
and with a ``fractional bandwidth'' of greater than 10%;
    b.4.e.2. A peak saturated power output greater than 20 mW (13 
dBm) at any frequency exceeding 75 GHz up to and

[[Page 45300]]

including 90 GHz, and with a ``fractional bandwidth'' of greater 
than 5%; or
    b.4.e.3. A peak saturated power output greater than 0.1 nW (-70 
dBm) at any frequency exceeding 90 GHz; or
    b.4.f. Rated for operation at frequencies above 2.7 GHz and all 
of the following:
    b.4.f.1. A peak saturated power output (in watts), 
Psat, greater than 400 divided by the maximum operating 
frequency (in GHz) squared [Psat > 400 W*GHz\2\/
fGHz\2\];
    b.4.f.2. A ``fractional bandwidth'' of 5% or greater; and
    b.4.f.3. Any two sides perpendicular to one another with either 
length d (in cm) equal to or less than 15 divided by the lowest 
operating frequency in GHz [d <= 15 cm*GHz/fGHz];

    Technical Note:
    2.7 GHz should be used as the lowest operating frequency (fGHz) 
in the formula in 3A001.b.4.f.3., for amplifiers that have a rated 
operation range extending downward to 2.7 GHz and below 
[d<=15cm*GHz/2.7 GHz].


N.B.: MMIC power amplifiers should be evaluated against the criteria 
in 3A001.b.2.

    Note 1:
    [RESERVED]


    Note 2:
    The control status of an item whose rated operating frequency 
includes frequencies listed in more than one frequency range, as 
defined by 3A001.b.4.a through 3A001.b.4.e, is determined by the 
lowest peak saturated power output control threshold.


    Note 3:
    3A001.b.4 includes transmit/receive modules and transmit 
modules.

* * * * *
    h. * * *

    Note 3:
    3A001.h. does not apply to switches, diodes, or `modules', 
incorporated into equipment designed for civil automobile, civil 
railway, or ``civil aircraft'' applications.


0
23. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 3, ECCN 3A002 is amended by:
0
a. Revising the heading;
0
b. Revising License Exception GBS and CIV paragraphs;
0
c. Revising the introductory text to paragraph a.;
0
d. Removing and reserving paragraphs a.1. through a.4;
0
e. Revising paragraph a.6;
0
f. Adding paragraph a.7;
0
g. Revising the introductory text to paragraph d.1.; and
0
h. Revising Technical Note 2 that appears after paragraph d.5.
    The revisions and additions read as follows:

3A002 General purpose electronic equipment, as follows (see List of 
Items Controlled).

* * * * *.

List Based License Exceptions (See Part 740 for a description of all 
license exceptions)

* * * * *
GBS: N/A.
CIV: N/A.
* * * * *

List of Items Controlled

* * * * *
Items:

    a. Recording equipment and oscilloscopes, as follows:
* * * * *
    a.6. Digital instrumentation data recorder systems using 
magnetic disk storage technique and having all of the following, and 
``specially designed'' digital recorders therefor:
    a.6.a. Digitized instrumentation data rate equal to or more than 
100 million samples per second and at a resolution of 8 bits or 
more; and
    a.6.b. A `continuous throughput' of 1 Gbit/s or more;

    Technical Note:
     Digital instrumentation data recorder systems can be configured 
either with a digitizer integrated within or outside the digital 
recorder.


    a.7. Real-time oscilloscopes having a vertical root-mean-square 
(rms) noise voltage of less than 2% of full-scale at the vertical 
scale setting that provides the lowest noise value for any input 3dB 
bandwidth of 60 GHz or greater per channel;

    Note:
     3A002.a.7 does not apply to equivalent-time sampling 
oscilloscopes.

* * * * *
    d. * * *
    d.1. Specified to generate pulse-modulated signals having all of 
the following, anywhere within the synthesized frequency range 
exceeding 31.8 GHz but not exceeding 75 GHz:
* * * * *
    d.5. * * *

    Technical Notes:

    1. The maximum synthesized frequency of an arbitrary waveform or 
function generator is calculated by dividing the sample rate, in 
samples/second, by a factor of 2.5.
    2. For the purposes of 3A002.d.1.a, `pulse duration' is defined 
as the time interval from the point on the leading edge that is 50% 
of the pulse amplitude to the point on the trailing edge that is 50% 
of the pulse amplitude.

* * * * *


0
24. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 3, ECCNs 3A982, 3D982 and 3E982 are removed.


0
25. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 3, ECCN 3A991 is amended by revising paragraph .d in the items 
paragraph of the List of Items Controlled section to read as follows:

3A991 Electronic devices, and ``components'' not controlled by 3A001.

* * * * *

List of Items Controlled

* * * * *
Items:
* * * * *
    d. Field programmable logic devices having a maximum number of 
single-ended digital input/outputs of 200 or greater and less than 
500;
* * * * *


0
26. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 3, ECCN 3C005 is amended by revising the heading to read as 
follows:

3C005 Silicon carbide (SiC), gallium nitride (GaN), aluminum nitride 
(AlN) or aluminum gallium nitride (AlGaN) semiconductor ``substrates'', 
or ingots, boules, or other preforms of those materials, having 
resistivities greater than 10,000 ohm-cm at 20 [deg]C.

* * * * *



0
27. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 3, ECCN 3E002 is amended by revising paragraph b. in the Items 
paragraph of the List of Items Controlled section to read as follows:

3E002 ``Technology'' according to the General Technology Note other 
than that controlled in 3E001 for the ``development'' or ``production'' 
of a ``microprocessor microcircuit'', ``micro-computer microcircuit'' 
and microcontroller microcircuit core, having an arithmetic logic unit 
with an access width of 32 bits or more and any of the following 
features or characteristics (see List of Items Controlled).

* * * * *

List of Items Controlled

* * * * *
Items:
* * * * *
    b. Designed to perform more than four 64-bit or larger floating-
point operation results per cycle; or
* * * * *

0
28. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 4, ECCN 4A003 is amended by:
0
a. Revising the AT paragraph in the License Requirements section;
0
b. Revising the Note in the License Requirements section; and
0
c. Revising paragraph b. in the Items paragraph of the List of Items 
Controlled section.
    The revisions read as follows:

4A003 ``Digital computers'', ``electronic assemblies'', and related 
equipment therefor, as follows (see List of Items Controlled) and 
``specially designed'' ``components'' therefor.

License Requirements

* * * * *

 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
 

[[Page 45301]]

 
                                * * * * *
AT applies to entire entry (refer to 4A994  AT Column 1.
 for controls on ``digital computers''
 with a APP >0.0128 but <=8.0 WT).
 
                                * * * * *
 

* * * * *

    Note:
    For all destinations, except those countries in Country Group 
E:1 of Supplement No. 1 to part 740 of the EAR, no license is 
required (NLR) for computers with an ``Adjusted Peak Performance'' 
(``APP'') not exceeding 8.0 Weighted TeraFLOPS (WT) and for 
``electronic assemblies'' described in 4A003.c that are not capable 
of exceeding an ``Adjusted Peak Performance'' (``APP'') exceeding 
8.0 Weighted TeraFLOPS (WT) in aggregation, except certain transfers 
as set forth in Sec.  746.3 (Iraq).

* * * * *

List of Items Controlled

* * * * *
Items:
* * * * *
    b. ``Digital computers'' having an ``Adjusted Peak Performance'' 
(``APP'') exceeding 8.0 weighted TeraFLOPS (WT);
* * * * *



0
29. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 4, ECCN 4D001 is amended by:
0
a. Revising the TSR paragraph in the List Based License Exceptions 
section;
0
b. Revising the Special Conditions for STA section; and
0
c. Revising paragraph b.1. in the Items paragraph of the List of Items 
Controlled section.
    The revisions read as follows:

4D001 ``Software'' as follows (see List of Items Controlled).

* * * * *

List Based License Exceptions (See Part 740 for a description of all 
license exceptions)

* * * * *
TSR: Yes, except for ``software'' for the ``development'' or 
``production'' of commodities with an ``Adjusted Peak Performance'' 
(``APP'') exceeding 1.0 WT.
* * * * *

Special Conditions for STA

STA: License Exception STA may not be used to ship or transmit 
``software'' ``specially designed'' for the ``development'' or 
``production'' of equipment specified by ECCN 4A001.a.2 or for the 
``development'' or ``production'' of ``digital computers'' having an 
`Adjusted Peak Performance' (`APP') exceeding 1.0 Weighted TeraFLOPS 
(WT) to any of the destinations listed in Country Group A:6 (See 
Supplement No.1 to part 740 of the EAR).

List of Items Controlled

* * * * *
Items:
* * * * *
    b. * * *:
    b.1. ``Digital computers'' having an ``Adjusted Peak 
Performance'' (``APP'') exceeding 0.60 Weighted TeraFLOPS (WT);
* * * * *
0
30. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 4, ECCN 4E001 is amended by:
0
a. Revising the TSR paragraph in the List Based License Exceptions 
section;
0
b. Revising the Special Conditions for STA section; and
0
c. Revising paragraph b.1. in the Items paragraph of the List of Items 
Controlled section.
    The revisions read as follows:

4E001 ``Technology'' as follows (see List of Items Controlled).

* * * * *

List Based License Exceptions (See Part 740 for a description of all 
license exceptions)

* * * * *
TSR: Yes, except for ``technology'' for the ``development'' or 
``production'' of commodities with an ``Adjusted Peak Performance'' 
(``APP'') exceeding 1.0 WT.
* * * * *

Special Conditions for STA

STA: License Exception STA may not be used to ship or transmit 
``technology'' according to the General Technology Note for the 
``development'' or ``production'' of any of the following equipment 
or ``software'': a. Equipment specified by ECCN 4A001.a.2; b. 
``Digital computers'' having an `Adjusted Peak Performance' (`APP') 
exceeding 1.0 Weighted TeraFLOPS (WT); or c. ``software'' specified 
in the License Exception STA paragraph found in the License 
Exception section of ECCN 4D001 to any of the destinations listed in 
Country Group A:6 (See Supplement No. 1 to part 740 of the EAR).

List of Items Controlled

* * * * *
Items:
* * * * *
    b. * * *
    b.1. ``Digital computers'' having an ``Adjusted Peak 
Performance'' (``APP'') exceeding 0.60 Weighted TeraFLOPS (WT);
* * * * *

0
31. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 5, Part 1, ECCN 5A001 is amended by:
0
a. Revising paragraphs b.1.d. and b.5.b. in the Items paragraph of the 
List of Items Controlled section; and
0
b. Adding a Technical Note after the Note following paragraph b.5.d. in 
the Items paragraph of the List of Items Controlled section.
    The revisions and addition read as follows:

5A001 Telecommunications systems, equipment, ``components'' and 
``accessories,'' as follows (see List of Items Controlled).

* * * * *

List of Items Controlled

* * * * *
Items:
* * * * *
    b. * * *
    b.1 * * *
    b.1.d. Using ``lasers'' or light-emitting diodes (LEDs), with an 
output wavelength greater than 400 nm and less than 700 nm, in a 
``local area network'';
* * * * *
    b.5. * * *
    b.5.b. A `channel switching time' of less than 1 ms;
* * * * *
    b.5.d. * * *

    Note: * * *

    Technical Note:
    `Channel switching time': the time (i.e., delay) to change from 
one receiving frequency to another, to arrive at or within 0.05% of the final specified receiving frequency. 
Items having a specified frequency range of less than 0.05% around their centre frequency are defined to 
be incapable of channel frequency switching.

* * * * *

0
32. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 5, Part 1, ECCN 5E001 is amended by removing paragraph d., 
including all subparagraphs, Notes, and Technical Notes, and adding in 
its place d., including all subparagraphs, Notes, and Technical Notes, 
in the Items paragraph of the List of Items Controlled section to read 
as follows:

5E001 ``Technology'' as follows (see List of Items Controlled).

* * * * *

List of Items Controlled

* * * * *
Items:
* * * * *
    d. ``Technology'' according to the General Technology Note for 
the ``development'' or ``production'' of Microwave Monolithic 
Integrated Circuit (MMIC) power amplifiers ``specially designed'' 
for telecommunications and that are any of the following:

    Technical Note:
     For purposes of 5E001.d, the parameter peak saturated power 
output may also be referred to on product data sheets as output 
power, saturated power output, maximum power output, peak power 
output, or peak envelope power output.

    d.1. Rated for operation at frequencies exceeding 2.7 GHz up to 
and including 6.8 GHz with a ``fractional bandwidth'' greater than 
15%, and having any of the following:

[[Page 45302]]

    d.1.a. A peak saturated power output greater than 75 W (48.75 
dBm) at any frequency exceeding 2.7 GHz up to and including 2.9 GHz;
    d.1.b. A peak saturated power output greater than 55 W (47.4 
dBm) at any frequency exceeding 2.9 GHz up to and including 3.2 GHz;
    d.1.c. A peak saturated power output greater than 40 W (46 dBm) 
at any frequency exceeding 3.2 GHz up to and including 3.7 GHz; or
    d.1.d. A peak saturated power output greater than 20 W (43 dBm) 
at any frequency exceeding 3.7 GHz up to and including 6.8 GHz;
    d.2. Rated for operation at frequencies exceeding 6.8 GHz up to 
and including 16 GHz with a ``fractional bandwidth'' greater than 
10%, and having any of the following:
    d.2.a. A peak saturated power output greater than 10W (40 dBm) 
at any frequency exceeding 6.8 GHz up to and including 8.5 GHz; or
    d.2.b. A peak saturated power output greater than 5W (37 dBm) at 
any frequency exceeding 8.5 GHz up to and including 16 GHz;
    d.3. Rated for operation with a peak saturated power output 
greater than 3 W (34.77 dBm) at any frequency exceeding 16 GHz up to 
and including 31.8 GHz, and with a ``fractional bandwidth'' of 
greater than 10%;
    d.4. Rated for operation with a peak saturated power output 
greater than 0.1n W (-70 dBm) at any frequency exceeding 31.8 GHz up 
to and including 37 GHz;
    d.5. Rated for operation with a peak saturated power output 
greater than 1 W (30 dBm) at any frequency exceeding 37 GHz up to 
and including 43.5 GHz, and with a ``fractional bandwidth'' of 
greater than 10%;
    d.6. Rated for operation with a peak saturated power output 
greater than 31.62 mW (15 dBm) at any frequency exceeding 43.5 GHz 
up to and including 75 GHz, and with a ``fractional bandwidth'' of 
greater than 10%;
    d.7. Rated for operation with a peak saturated power output 
greater than 10 mW (10 dBm) at any frequency exceeding 75 GHz up to 
and including 90 GHz, and with a ``fractional bandwidth'' of greater 
than 5%; or
    d.8. Rated for operation with a peak saturated power output 
greater than 0.1 nW (-70 dBm) at any frequency exceeding 90 GHz;
* * * * *

0
33. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 5, Part 2 is amended by:
0
a. Revising paragraph b. of Note 3 to read as follows; and
0
b. Removing the Technical Note at the end of Note 4 that reads ``Parity 
bits are not included in the key length.''
    The revision reads as follows:

CATEGORY 5--TELECOMMUNICATIONS AND ``INFORMATION SECURITY''

* * * * *

Part 2--``INFORMATION SECURITY''

* * * * *
    Note 3: * * *

    b. * * *
    3. The feature set of the component or `executable software' is 
fixed and is not designed or modified to customer specification; and
* * * * *

0
34. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 5, Part 2, ECCN 5A002 is amended by:
0
a. Revising paragraphs (i) and (j), and adding paragraph (k) to the 
Note at the beginning of the Items paragraph of the List of Items 
Controlled section;
0
b. Revising the Nota Bena after the introductory text of paragraph a. 
in the Items paragraph of the List of Items Controlled section;
0
c. Removing paragraph 3 in the Technical Note to 5A002.a.1. in the 
Items paragraph of the List of Items Controlled section;
0
d. Removing the Note to 5A002.a.1. in the Items paragraph of the List 
of Items Controlled section;
0
e. Adding a Technical Note after the introductory text of paragraph 
a.1.a. in the Items paragraph of the List of Items Controlled section; 
and
0
f. Revising the introductory text to paragraph a.9. in the Items 
paragraph of the List of Items Controlled section.
    The revisions and addition read as follows:

5A002 ``Information security'' systems, equipment ``components'' 
therefor, as follows (see List of Items Controlled).

* * * * *

 List of Items Controlled

* * * * *
Items:

    Note:
    * * *


    (i) Wireless ``personal area network'' equipment that implement 
only published or commercial cryptographic standards and where the 
cryptographic capability is limited to a nominal operating range not 
exceeding 30 meters according to the manufacturer's specifications, 
or not exceeding 100 meters according to the manufacturer's 
specifications for equipment that cannot interconnect with more than 
seven devices;
    (j) Equipment, having no functionality specified by 5A002.a.2, 
5A002.a.4, 5A002.a.7, or 5A002.a.8, where all cryptographic 
capability specified by 5A002.a meets any of the following:
    1. It cannot be used; or
    2. It can only be made useable by means of ``cryptographic 
activation''; or
N.B.: See 5A002.a for equipment that has undergone ``cryptographic 
activation.''
    (k) Mobile telecommunications Radio Access Network (RAN) 
equipment designed for civil use, which also meet the provisions 2. 
to 5. of part a. of the Cryptography Note (Note 3 in Category 5, 
Part 2), having an RF output power limited to 0.1W (20 dBm) or less, 
and supporting 16 or fewer concurrent users.
    a. * * *
N.B.: For the control of Global Navigation Satellite Systems (GNSS) 
receiving equipment containing or employing decryption, see ECCN 
7A005, and for related decryption ``software'' and ``technology'' 
see 7D005 and 7E001.
    a.1. * * *
    a.1.a. * * *

    Technical Note:
    Parity bits are not included in the key length.

* * * * *
    a.9. Designed or modified to use or perform `quantum 
cryptography.'
* * * * *

0
35. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 6, ECCN 6A001 is amended by:
0
a. Adding Note 3 to the introductory paragraph a.1.c. in the Items 
paragraph of the List of Items Controlled section;
0
b. Revising the Technical Note following a.1.c.2., the introductory 
text to paragraph a.1.e., a.2.a.3. through a.2.a.3.e., a.2.b.7., and 
a.2.e. through a.2.e.3.;
0
c. Removing and reserving paragraph a.2.b.6.
0
c. Adding paragraphs a.2.b.8 and a.2.g. through a.2.g.4., and one Note 
to 6A001.a.2 and two Technical Notes following the Note to 
6A001.a.2.g.; and
0
d. Removing the Note after paragraph a.2.f. and adding it after new 
paragraph a.2.g.4. in the Items paragraph of the List of Items 
Controlled section.
    The revisions and additions read as follows:

6A001 Acoustic systems, equipment and components, as follows (see List 
of Items Controlled).

* * * * *

List of Items Controlled

* * * * *
Items:
    a. * * *
    a.1. * * *
    a.1.c. * * *

    Note:

* * * * *
    3. Piezoelectric elements specified in 6A001.a.1.c include those 
made from lead-magnesium-niobate/lead-titanate 
(Pb(Mg1/3Nb2/3)O3-
PbTiO3, or PMN-PT) single crystals grown from solid 
solution or lead-indium-niobate/lead-magnesium niobate/lead-titanate 
(Pb(In1/2Nb1/2)O3-
Pb(Mg1/3Nb2/3)O3-PbTiO3, 
or PIN-PMN-PT) single crystals grown from solid solution.
* * * * *
    a.1.c.2. * * *

    Technical Note:
    `Acoustic power density' is obtained by dividing the output 
acoustic power by the product of the area of the radiating surface 
and the frequency of operation.

* * * * *
    a.1.e. Active individual sonars, ``specially designed'' or 
modified to detect, locate and

[[Page 45303]]

automatically classify swimmers or divers, having all of the 
following, and ``specially designed'' transmitting and receiving 
acoustic arrays therefor:
* * * * *
    a.2. * * *
    a.2.a. * * *
    a.2.a.3. Having any of the following sensing elements:
    a.2.a.3.a. Optical fibers;
    a.2.a.3.b. `Piezoelectric polymer films' other than 
polyvinylidene-fluoride (PVDF) and its co-polymers {P(VDF-TrFE) and 
P(VDF-TFE){time} ;
    a.2.a.3.c. `Flexible piezoelectric composites';
    a.2.a.3.d. Lead-magnesium-niobate/lead-titanate (i.e., 
Pb(Mg1/3Nb2/3)O3-PbTiO3, 
or PMN-PT) piezoelectric single crystals grown from solid solution; 
or
    a.2.a.3.e. Lead-indium-niobate/lead-magnesium niobate/lead-
titanate (i.e., Pb(In1/2Nb1/2)O3-
Pb(Mg1/3Nb2/3)O3-PbTiO3, 
or PIN-PMN-PT) piezoelectric single crystals grown from solid 
solution;
* * * * *
    a.2.b. * * *
    a.2.b.6. [RESERVED];
    a.2.b.7. Hydrophone characteristics controlled by 6A001.a.2.a; 
or
    a.2.b.8. Accelerometer-based hydro-acoustic sensors specified by 
6A001.a.2.g;
* * * * *
    a.2.e. Bottom or bay-cable hydrophone arrays having any of the 
following:
    a.2.e.1. Incorporating hydrophones controlled by 6A001.a.2.a;
    a.2.e.2. Incorporating multiplexed hydrophone group signal 
modules having all of the following characteristics:
    a.2.e.2.a. Designed to operate at depths exceeding 35 m or 
having an adjustable or removal depth sensing device in order to 
operate at depths exceeding 35 m; and
    a.2.e.2.b. Capable of being operationally interchanged with 
towed acoustic hydrophone array modules; or
    a.2.e.3. Incorporating accelerometer-based hydro-acoustic 
sensors specified by 6A001.a.2.g;
    a.2.f. * * *
    a.2.g. Accelerometer-based hydro-acoustic sensors having all of 
the following:
    a.2.g.1. Composed of three accelerometers arranged along three 
distinct axes;
    a.2.g.2. Having an overall `acceleration sensitivity' better 
than 48 dB (reference 1,000 mV rms per 1g);
    a.2.g.3. Designed to operate at depths greater than 35 meters; 
and
    a.2.g.4. Operating frequency below 20 kHz;

    Note:
    6A001.a.2.g does not apply to particle velocity sensors or 
geophones.


    Note:
    6A001.a.2 also applies to receiving equipment, whether or not 
related in normal application to separate active equipment, and 
``specially designed'' components therefor.


    Technical Notes:

    1. Accelerometer-based hydro-acoustic sensors are also known as 
vector sensors.
    2. `Acceleration sensitivity' is defined as twenty times the 
logarithm to the base 10 of the ratio of rms output voltage to a 1 V 
rms reference, when the hydro-acoustic sensor, without a 
preamplifier, is placed in a plane wave acoustic field with an rms 
acceleration of 1 g (i.e., 9.81 m/s\2\).

* * * * *

0
36. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 6, ECCN 6A005 is amended by:
0
a. Revising the NP paragraph in the License Requirement section;
0
b. Removing the License Requirements Note;
0
c. Revising License Exception paragraphs GBS and CIV in the List Based 
License Exception section;
0
d. Revising the Related Definitions paragraph in the List of Items 
Controlled section;
0
e. Revising Note 2 and adding a Technical Note after Note 2 at the 
beginning of the Items paragraph in the List of Items Controlled 
section;
0
f. Revising the Note below paragraph a.6.b.2. to make it ``Note 1'' and 
adding Note 2 and a Technical Note;
0
g. Removing paragraphs b.4., b.5., and b.6. and adding in place b.4., 
b.5., and .b.6.; and
0
h. Removing the Note below paragraph d.6.b.
    The revisions read as follows:

6A005 ``Lasers,'' ``components'' and optical equipment, as follows (see 
List of Items Controlled), excluding items that are subject to the 
export licensing authority of the Nuclear Regulatory Commission (see 10 
CFR part 110).

License Requirements

Reason for Control: NS, NP, AT

 
                Control(s)                          Country Chart
 
NS applies to entire entry................  NS Column 2.
NP applies to ``lasers'' that meet or       NP Column 1.
 exceed the parameters of 6A205.
AT applies to entire entry................  AT Column 1.
 

List Based License Exceptions (See Part 740 for a description of all 
license exceptions)

LVS: N/A for NP items
    $3000 for all other items
GBS: Neodymium-doped (other than glass) ``lasers'' controlled by 
6A005.b.6.d.2 (except 6A005.b.6.d.2.b) that have an output 
wavelength exceeding 1,000 nm, but not exceeding 1,100 nm, and an 
average or CW output power not exceeding 2kW, and operate in a 
pulse-excited, non- ``Q-switched'' multiple-transverse mode, or in a 
continuously excited, multiple-transverse mode; Dye and Liquid 
Lasers controlled by 6A005.c.1, c.2 and c.3, except for a pulsed 
single longitudinal mode oscillator having an average output power 
exceeding 1 W and a repetition rate exceeding 1 kHz if the ``pulse 
duration'' is less than 100 ns; CO ``lasers'' controlled by 
6A005.d.2 having a CW maximum rated single or multimode output power 
not exceeding 10 kW; CO2 or CO/CO2 ``lasers'' 
controlled by 6A005.d.3 having an output wavelength in the range 
from 9,000 to 11,000 nm and having a pulsed output not exceeding 2 J 
per pulse and a maximum rated average single or multimode output 
power not exceeding 5 kW; CO2 ``lasers'' controlled by 
6A005.d.3 that operate in CW multiple-transverse mode, and having a 
CW output power not exceeding 15kW; and 6A005.f.1.
CIV: Neodymium-doped (other than glass) ``lasers'' controlled by 
6A005.b.6.d.2 (except 6A005.b.6.d.2.b) that have an output 
wavelength exceeding 1,000 nm, but not exceeding 1,100 nm, and an 
average or CW output power not exceeding 2kW, and operate in a 
pulse-excited, non- ``Q-switched'' multiple-transverse mode, or in a 
continuously excited, multiple-transverse mode; Dye and Liquid 
Lasers controlled by 6A005.c.1, c.2 and c.3, except for a pulsed 
single longitudinal mode oscillator having an average output power 
exceeding 1 W and a repetition rate exceeding 1 kHz if the ``pulse 
duration'' is less than 100 ns; CO ``lasers'' controlled by 
6A005.d.2 having a CW maximum rated single or multimode output power 
not exceeding 10 kW; CO2 or CO/CO2 ``lasers'' 
controlled by 6A005.d.3 having an output wavelength in the range 
from 9,000 to 11,000 nm and having a pulsed output not exceeding 2 J 
per pulse and a maximum rated average single or multimode output 
power not exceeding 5 kW; CO2 ``lasers'' controlled by 
6A005.d.3 that operate in CW multiple-transverse mode, and having a 
CW output power not exceeding 15kW; and 6A005.f.1.

List of Items Controlled

Related Controls: (1) See ECCN 6D001 for ``software'' for items 
controlled under this entry. (2) See ECCNs 6E001 (``development''), 
6E002 (``production''), and 6E201 (``use'') for technology for items 
controlled under this entry. (3) Also see ECCNs 6A205 and 6A995. (4) 
See ECCN 3B001 for excimer ``lasers'' ``specially designed'' for 
lithography equipment. (5) ``Lasers'' ``specially designed'' or 
prepared for use in isotope separation are subject to the export 
licensing authority of the Nuclear Regulatory Commission (see 10 CFR 
part 110). (6) Shared aperture optical elements, capable of 
operating in ``super-high power laser'' applications, and ``lasers'' 
specifically designed, modified, or configured for military 
application are ``subject to the ITAR'' (see 22 CFR parts 120 
through 130).
Related Definitions: (1) `Wall-plug efficiency' is defined as the 
ratio of ``laser'' output power (or ``average output power'') to 
total electrical input power required to operate the ``laser'', 
including the power supply/conditioning and thermal conditioning/
heat exchanger, see 6A005.a.6.b.1 and 6A005.b.6; (2) `Non-repetitive 
pulsed' refers to ``lasers'' that produce either a single output 
pulse or that have a time interval between pulses exceeding one 
minute, see Note 2 of 6A005 and 6A005.d.6.

[[Page 45304]]

Items:
* * * * *

    Note 2:
     Excimer, semiconductor, chemical, CO, CO2, and `non-
repetitive pulsed' Nd:glass ``lasers'' are only specified by 
6A005.d.


    Technical Note:
     `Non-repetitive pulsed' refers to ``lasers'' that produce 
either a single output pulse or that have a time interval between 
pulses exceeding one minute.

* * * * *
    a. * * *
    a.6. * * *
    a.6.b. * * *
    a.6.b.2. * * *

    Note 1:
     6A005.a.6.b does not control multiple transverse mode, 
industrial ``lasers'' with output power exceeding 2kW and not 
exceeding 6 kW with a total mass greater than 1,200 kg. For the 
purpose of this note, total mass includes all ``components'' 
required to operate the ``laser,'' e.g., ``laser,'' power supply, 
heat exchanger, but excludes external optics for beam conditioning 
and/or delivery.


    Note 2:
     6A005.a.6.b does not apply to multiple transverse mode, 
industrial ``lasers'' having any of the following:


    a. Output power exceeding 500 W but not exceeding 1 kW and 
having all of the following:
    1. Beam Parameter Product (BPP) exceeding 0.7 
mmmrad; and
    2. `Brightness' not exceeding 1024 W/
(mmmrad);\2\
    b. Output power exceeding 1 kW but not exceeding 1.6 kW and 
having a BPP exceeding 1.25 mmmrad;
    c. Output power exceeding 1.6 kW but not exceeding 2.5 kW and 
having a BPP exceeding 1.7 mmmrad;
    d. Output power exceeding 2.5 kW but not exceeding 3.3 kW and 
having a BPP exceeding 2.5 mmmrad;
    e. Output power exceeding 3.3 kW but not exceeding 4 kW and 
having a BPP exceeding 3.5 mmmrad;
    f. Output power exceeding 4 kW but not exceeding 5 kW and having 
a BPP exceeding 5 mmmrad;
    g. Output power exceeding 5 kW but not exceeding 6 kW and having 
a BPP exceeding 7.2 mmmrad;
    h. Output power exceeding 6 kW but not exceeding 8 kW and having 
a BPP exceeding 12 mmmrad; or
    i. Output power exceeding 8 kW but not exceeding 10 kW and 
having a BPP exceeding 24 mmmrad;

    Technical Note:
     For the purpose of 6A005.a.6.b, Note 2.a., `brightness' is 
defined as the output power of the ``laser'' divided by the squared 
Beam Parameter Product (BPP), i.e., (output power)/BPP\2\.

* * * * *
    b. * * *
    b.4. Output wavelength exceeding 540 nm but not exceeding 800 nm 
and any of the following:
    b.4.a. ``Pulse duration'' less than 1 ps and any of the 
following:
    b.4.a.1. Output energy exceeding 0.005 J per pulse and ``peak 
power'' exceeding 5 GW; or
    b.4.a.2. ``Average output power'' exceeding 20 W; or
    b.4.b. ``Pulse duration'' equal to or exceeding 1 ps and any of 
the following:
    b.4.b.1. Output energy exceeding 1.5 J per pulse and ``peak 
power'' exceeding 30 W; or
    b.4.b.2. ``Average output power'' exceeding 30 W;
    b.5. Output wavelength exceeding 800 nm but not exceeding 975 nm 
and any of the following:
    b.5.a. ``Pulse duration'' less than 1ps and any of the 
following:
    b.5.a.1. Output energy exceeding 0.005 J per pulse and ``peak 
power'' exceeding 5 GW; or
    b.5.a.2. Single transverse mode output and ``average output 
power'' exceeding 20 W;
    b.5.b. ``Pulse duration'' equal to or exceeding 1 ps and not 
exceeding 1 [mu]s and any of the following:
    b.5.b.1. Output energy exceeding 0.5 J per pulse and ``peak 
power'' exceeding 50 W;
    b.5.b.2. Single transverse mode output and ``average output 
power'' exceeding 20 W; or
    b.5.b.3. Multiple transverse mode output and ``average output 
power'' exceeding 50 W; or
    b.5.c. ``Pulse duration'' exceeding 1 [mu]s and any of the 
following:
    b.5.c.1. Output energy exceeding 2 J per pulse and ``peak 
power'' exceeding 50 W;
    b.5.c.2. Single transverse mode output and ``average output 
power'' exceeding 50 W; or
    b.5.c.3. Multiple transverse mode output and ``average output 
power'' exceeding 80 W.
    b.6. Output wavelength exceeding 975 nm but not exceeding 1,150 
nm and any of the following:
    b.6.a. ``Pulse duration'' of less than 1 ps, and any of the 
following:
    b.6.a.1. Output ``peak power'' exceeding 2 GW per pulse;
    b.6.a.2. ``Average output power'' exceeding 10 W; or
    b.6.a.3. Output energy exceeding 0.002 J per pulse;
    b.6.b. ``Pulse duration'' equal to or exceeding 1 ps and less 
than 1 ns, and any of the following:
    b.6.b.1. Output ``peak power'' exceeding 5 GW per pulse;
    b.6.b.2. ``Average output power'' exceeding 10 W; or
    b.6.b.3. Output energy exceeding 0.1 J per pulse;
    b.6.c. ``Pulse duration'' equal to or exceeding 1 ns but not 
exceeding 1 [mu]s and any of the following:
    b.6.c.1. Single transverse mode output and any of the following:
    b.6.c.1.a. ``Peak power'' exceeding 100 MW;
    b.6.c.1.b. ``Average output power'' exceeding 20 W limited by 
design to a maximum pulse repetition frequency less than or equal to 
1 kHz;
    b.6.c.1.c. `Wall-plug efficiency' exceeding 12%, ``average 
output power'' exceeding 100 W and capable of operating at a pulse 
repetition frequency greater than 1 kHz;
    b.6.c.1.d. ``Average output power'' exceeding 150 W and capable 
of operating at a pulse repetition frequency greater than 1 kHz; or
    b.6.c.1.e. Output energy exceeding 2 J per pulse; or
    b.6.c.2. Multiple transverse mode output and any of the 
following:
    b.6.c.2.a. ``Peak power'' exceeding 400 MW;
    b.6.c.2.b. `Wall-plug efficiency' exceeding 18% and ``average 
output power'' exceeding 500 W;
    b.6.c.2.c. ``Average output power'' exceeding 2 kW; or
    b.6.c.2.d. Output energy exceeding 4 J per pulse; or
    b.6.d. ``Pulse duration'' exceeding 1 [mu]s and any of the 
following:
    b.6.d.1. Single transverse mode output and any of the following:
    b.6.d.1.a. ``Peak power'' exceeding 500 kW;
    b.6.d.1.b. `Wall-plug efficiency' exceeding 12% and ``average 
output power'' exceeding 100 W; or
    b.6.d.1.c. ``Average output power'' exceeding 150 W; or
    b.6.d.2. Multiple transverse mode output and any of the 
following:
    b.6.d.2.a. ``Peak power'' exceeding 1 MW;
    b.6.d.2.b. `Wall-plug efficiency' exceeding 18% and ``average 
output power'' exceeding 500 W; or
    b.6.d.2.c. ``Average output power'' exceeding 2 kW;
* * * * *
    d. Other ``lasers'', not controlled by 6A005.a., 6A005.b, or 
6A005.c as follows:
* * * * *



0
37. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 6, ECCN 6A007 is amended by:
0
a. Removing ``[micro]gal'' and adding in its place ``[micro]Gal'' in 
paragraph 6A007.a; and
0
b. Revising paragraphs b.1. and b.2. in the Items paragraph of the List 
of Items Controlled section.
    The revisions read as follows:

6A007 Gravity Meters (Gravimeters) and Gravity Gradiometers, as Follows 
(see List of Items Controlled)

* * * * *

List of Items Controlled

* * * * *
Items:
* * * * *
    b. * * *
    b.1. A static accuracy of less (better) than 0.7 mGal; and
    b.2. An in-service (operational) accuracy of less (better) than 
0.7 mGal having a `time-to-steady-state registration' of less than 2 
minutes under any combination of attendant corrective compensations 
and motional influences;
* * * * *



0
38. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 6, ECCN 6A008 is amended by:
0
a. Revising paragraph k.2., and adding a Note to 6A008.k, in the Items 
paragraph of the List of Items Controlled section;
0
b. Revising the Note to 6A008.l.1. following paragraph l.1. in the 
Items

[[Page 45305]]

paragraph of the List of Items Controlled section;
0
c. Revising the Note to 6A008.1 following the Nota Bene after paragraph 
l.4; and
0
d. Adding Technical Notes to the end of the Items paragraph of the List 
of Items Controlled section, to read as follows:

6A008 Radar systems, equipment and assemblies, having any of the 
following (see List of Items Controlled), and ``specially designed'' 
``components'' therefor.

* * * * *

List of Items Controlled

* * * * *
Items:
* * * * *
    k. * * *
    k.2. A compressed pulse width of less than 200 ns; or

    Note:
     6A008.k.2 does not apply to two dimensional `marine radar' or 
`vessel traffic service' radar, having all of the following:
    a. ``Pulse compression'' ratio not exceeding 150;
    b. Compressed pulse width of greater than 30 ns;
    c. Single and rotating mechanically scanned antenna;
    d. Peak output power not exceeding 250 W; and
    e. Not capable of ``frequency hopping''.

    l. * * *
    l.1. * * *

    Note:
     6A008.l.1 does not control conflict alert capability in ATC 
systems, or `marine radar'.

* * * * *
    l.4. * * *
    N.B.: * * *

    Note:
    6A008.l does not apply to systems, equipment and assemblies 
designed for `vessel traffic services'.


    Technical Notes:

    1. For the purposes of 6A008, `marine radar' is a radar that is 
used to navigate safely at sea, inland waterways or near-shore 
environments.
    2. For the purposes of 6A008, `vessel traffic service' is a 
vessel traffic monitoring and control service similar to air traffic 
control for aircraft.




0
39. ECCN 6A205 is amended by removing the reference to ``6A005.b.6.b'' 
and adding in its place ``6A005.b.6.c'' in paragraph (3) of the Related 
Controls paragraph of the List of Items Controlled section.

0
40. In Supplement No. 1 to part 774 (the Commerce Control List, 
Category 6, ECCN 6B007, the heading is amended by removing ``mgal'' and 
adding in its place ``mGal.''

0
41. In Supplement No. 1 to part 774 (the Commerce Control List, 
Category 6, ECCN 6D001 is amended by removing ``NP'' from the reason 
for control paragraph and the NP control paragraph in the License 
Requirements section.

0
42. ECCN 6E201 is amended by revising the heading to read as follows:

6E201 ``Technology'' according to the General Technology Note for the 
``use'' of equipment controlled by 6A003.a.2., 6A003.a.3, 6A003.a.4; 
6A005.a.2, 6A005.b.2.b, 6A005.b.3, 6A005.b.4.b.2, 6A005.b.6.c, 
6A005.c.1.b, 6A005.c.2.b, 6A005.d.2, 6A005.d.3.c, or 6A005.d.4.c (that 
meet or exceed the parameters of 6A205); 6A202, 6A203, 6A205, 6A225 or 
6A226.

* * * * *

0
43. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 7, ECCN 7A002 is amended by:
0
a. Revising the Note to 7A002.a.1.b in the Items paragraph of the List 
of Items Controlled section;
0
b. Removing the Technical Note below the Note to 7A002.a.1.b in the 
Items paragraph of the List of Items Controlled section; and
0
c. Revising paragraphs a.2.a. and a.2.b., and the Note to 7A002.a.2.b 
in the Items paragraph of the List of Items Controlled section.
    The revisions read as follows:

7A002 Gyros or angular rate sensors, having any of the following (see 
List of Items Controlled) and ``specially designed'' ``components'' 
therefor.

* * * * *

List of Items Controlled

* * * * *
Items:

    a. * * *
    a.1. * * *
    a.1.b. * * *

    Note:
    7A002.a.1.b does not control ``spinning mass gyros''.


    a.2. * * *
    a.2.a. A ``bias'' ``stability'' of less (better) than 4 degrees 
per hour, when measured in a 1 g environment over a period of three 
minutes, and with respect to a fixed calibration value; or
    a.2.b. An ``angle random walk'' of less (better) than or equal 
to 0.1 degree per square root hour; or

    Note:
    7A002.a.2.b does not apply to ``spinning mass gyros''.

* * * * *

0
44. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 7, ECCN 7A003 is amended by:
0
a. Revising the heading;
0
b. Removing the text and adding in its place ``N/A'' in the Related 
Definitions paragraph of the List of Items Controlled section; and
0
c. Revising the Items paragraph in the List of Items Controlled 
section.
    The revisions read as follows:

7A003 `Inertial measurement equipment or systems', having any of the 
following (see List of Items Controlled).

* * * * *

List of Items Controlled

* * * * *
Items:

    Note 1:
     `Inertial measurement equipment or systems' incorporate 
accelerometers or gyroscopes to measure changes in velocity and 
orientation in order to determine or maintain heading or position 
without requiring an external reference once aligned. `Inertial 
measurement equipment or systems' include:

    --Attitude and Heading Reference Systems (AHRSs);
    --Gyrocompasses;
    --Inertial Measurement Units (IMUs);
    --Inertial Navigation Systems (INSs);
    --Inertial Reference Systems (IRSs);
    --Inertial Reference Units (IRUs).

    Note 2:
    7A003 does not apply to `inertial measurement equipment or 
systems' which are certified for use on ``civil aircraft'' by civil 
authorities of a Wassenaar Arrangement Participating State, see 
Supplement No. 1 to part 743 of the EAR.


    Technical Notes:

    1. `Positional aiding references' independently provide 
position, and include:
    a. Global Navigation Satellite Systems (GNSS);
    b.''Data-Based Referenced Navigation'' (``DBRN'').
    2. `Circular Error Probable' (`CEP')--In a circular normal 
distribution, the radius of the circle containing 50% of the 
individual measurements being made, or the radius of the circle 
within which there is a 50% probability of being located.


    a. Designed for ``aircraft'', land vehicles or vessels, 
providing position without the use of `positional aiding 
references', and having any of the following accuracies subsequent 
to normal alignment:
    a.1. 0.8 nautical miles per hour (nm/hr) `Circular Error 
Probable' (`CEP') rate or less (better);
    a.2. 0.5% distanced travelled `CEP' or less (better); or
    a.3. Total drift of 1 nautical mile `CEP' or less (better) in a 
24 hr period;

    Technical Note:
    The performance parameters in 7A003.a.1, 7A003.a.2 and 7A003.a.3 
typically apply to `inertia measurement equipment or systems' 
designed for ``aircraft'', vehicles and vessels, respectively. These 
parameters result from the utilization of specialized non-positional 
aiding references (e.g., altimeter, odometer, velocity log). As a 
consequence, the specified performance values cannot be readily 
converted between these parameters. Equipment designed for multiple 
platforms are evaluated against each applicable entry 7A003.a.1, 
7A003.a.2, or 7A003.a.3.


    b. Designed for ``aircraft'', land vehicles or vessels, with an 
embedded `positional aiding reference' and providing position after 
loss of all `positional aiding references' for a period of up to 4 
minutes, having an accuracy of less (better) than 10 meters `CEP';


[[Page 45306]]


    Technical Note:
    7A003.b refers to systems in which `inertial measurement 
equipment or systems' and other independent `positional aiding 
references' are built into a single unit (i.e., embedded) in order 
to achieve improved performance.


    c. Designed for ``aircraft'', land vehicles or vessels, 
providing heading or True North determination and having any of the 
following:
    c.1. A maximum operating angular rate less (lower) than 500 deg/
s and a heading accuracy without the use of `positional aiding 
references' equal to or less (better) than 0.07 deg sec (Lat) 
(equivalent to 6 arc minutes rms at 45 degrees latitude); or
    c.2. A maximum operating angular rate equal to or greater 
(higher) than 500 deg/s and a heading accuracy without the use of 
`positional aiding references' equal to or less (better) than 0.2 
deg sec (Lat) (equivalent to 17 arc minutes rms at 45 degrees 
latitude);
    d. Providing acceleration measurements or angular rate 
measurements, in more than one dimension, and having any of the 
following:
    d.1. Performance specified by 7A001 or 7A002 along any axis, 
without the use of any aiding references; or
    d.2. Being ``space-qualified'' and providing angular rate 
measurements having an ``angle random walk'' along any axis of less 
(better) than or equal to 0.1 degree per square root hour.

    Note:
    7A003.d.2 does not apply to `inertial measurement equipment or 
systems' that contain ``spinning mass gyros'' as the only type of 
gyro.



0
45. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 7, ECCN 7D003 is amended by:
0
a. Revising the Special Conditions for STA section; and
0
b. Removing and reserving paragraph 7D003.c.
    The revision reads as follows:

7D003 Other ``software'' as follows (see List of Items Controlled).

* * * * *

Special Conditions for STA

STA: License Exception STA may not be used to ship or transmit 
software in 7D003.a or .b to any of the destinations listed in 
Country Group A:6 (See Supplement No.1 to part 740 of the EAR).
* * * * *

0
46. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 7, ECCN 7D004 is amended by revising the heading to read as 
follows:

7D004 ``Source code'' incorporating ``development'' ``technology'' 
specified by 7E004.a.1 to a.6 or 7E004.b, for any of the following: 
(see List of Items Controlled).

* * * * *

0
47. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 7 is amended by adding ECCN 7D005 to read as follows:

7D005 ``Software'' ``specially designed'' to decrypt Global Navigation 
Satellite Systems (GNSS) ranging signals designed for government use.

License Requirements

Reason for Control: NS, AT

 
                                            Country Chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to entire entry................  NS Column 1.
AT applies to entire entry................  AT Column 1.
 

List Based License Exceptions (See Part 740 for a description of all 
license exceptions)

CIV: N/A
TSR: N/A

List of Items Controlled

Related Controls: N/A
Related Definitions: N/A
Items:

    The list of items controlled is contained in the ECCN heading.

0
48. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 7, ECCN 7E001 is amended by:
0
a. Revising the heading;
0
b. Revising the NS paragraph in the License Requirements section; and
0
c. Adding a Note to the end of the Items paragraph of the List of Items 
Controlled section.
    The revisions and addtion to read as follows:

7E001 ``Technology'' according to the General Technology Note for the 
``development'' of equipment or ``software'', specified by 7.A., 7.B., 
7D001, 7D002, 7D003 or 7D005.

License Requirements

* * * * *

 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738).
 
NS applies to ``technology'' for items      NS Column 1.
 controlled by 7A001 to 7A004, 7A006,
 7A008, 7B001 to 7B003, 7D001 to 7D005.
 
                                * * * * *
 

* * * * *

List of Items Controlled

* * * * *
Items:

    The list of items controlled is contained in the ECCN heading.

    Note:
     7E001 includes key management ``technology'' exclusively for 
equipment specified in 7A005.a.



0
49. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 7, ECCN 7E004 is amended by removing and reserving paragraph 
b.6 and removing the Nota Bene below it. Note that 7E004.b remains.

0
50. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 8, ECCN 8A002 is amended by:
0
a. Revising paragraph i.2 and the Technical Note below it in the Items 
paragraph of the List of Items Controlled; and
0
b. Adding a Nota Bene below the Note that follows paragraph q.2 in the 
Items paragraph of the List of Items Controlled section.
    The revisions and addition read as follows:

8A002 Marine systems, equipment, ``parts'' and ``components,'' as 
follows (see List of Items Controlled).

* * * * *

List of Items Controlled

* * * * *
Items:
* * * * *
    i. * * *
    i.2. Controlled by proportional master-slave techniques and 
having 5 degrees of `freedom of movement' or more;

    Technical Note:
    Only functions having proportionally related motion control 
using positional feedback are counted when determining the number of 
degrees of `freedom of movement'.

* * * * *
    q. * * *
    q.2. * * *

    Note:
    * * *


N.B. For equipment and devices ``specially designed'' for military 
use see ECCN 8A620.f.
* * * * *

0
51. In Supplement No. 1 to Part 774 (the Commerce Control List), 
Category 9, ECCN 9A001 is amended by revising the Note to 9A001.a to be 
Note 1 and adding Note 2 following 9A001.a in the Items paragraph of 
the List of Items Controlled section, to read as follows:

9A001 Aero gas turbine engines having any of the following (see List of 
Items Controlled).

* * * * *

List of Items Controlled

* * * * *
Items:

    a. * * *

    Note 1:
    9A001.a. does not control aero gas turbine engines which meet 
all of the following:
    a. Certified by the civil aviation authority in a country listed 
in Supplement No. 1 to Part 743; and
    b. Intended to power non-military manned aircraft for which any 
of the following has been issued by a Wassenaar Arrangement 
Participating State listed in Supplement No.

[[Page 45307]]

1 to Part 743 for the aircraft with this specific engine type:
    b.1. A civil type certificate; or
    b.2. An equivalent document recognized by the International 
Civil Aviation Organization (ICAO).


    Note 2:
     9A001.a does not apply to aero gas turbine engines for 
Auxiliary Power Units (APUs) approved by the civil aviation 
authority in a Wassenaar Arrangement Participating State (see 
Supplement No. 1 to part 743 of the EAR).

* * * * *

0
52. Supplement No. 2 to part 774 ``General Technology and Software 
Notes'' is amended by removing the phrase ``operation, maintenance 
(checking), and repair'' and adding in its place ``operation, 
maintenance (checking), or repair'' in the General Technology Note.

0
53. Supplement No. 5 to part 774 ``Items Classified Under ECCNS 0A521, 
0B521, 0C521, 0D521 and 0E521'' is amended by removing the date ``June 
20, 2014'' and adding in its place ``June 20, 2015'' from rows 0D521 
No. 2 and 0E521 No. 6 and under the column entitled ``Date when the 
item will be designated EAR99, unless reclassified in another ECCN or 
the 0Y521 classification is reissued.''

0
54. Supplement No. 6 to part 774 ``Sensitive List'' is amended by:
0
a. Revising paragraphs (4)(ii) and (iii);
0
b. Removing and reserving paragraph (7)(iv);
0
c. Redesignating paragraphs (7)(v) and (vi) as paragraphs (7)(vi) and 
(vii);
0
d. Adding new paragraph (7)(v).
    The revisions and addition read as follows:

Supplement No. 6 to Part 774--Sensitive List

* * * * *
    (4) * * *
    (ii) 4D001--''Software'' ``specially designed'' for the 
``development'' or ``production'' of equipment controlled under ECCN 
4A001.a.2 or for the ``development'' or ``production'' of ``digital 
computers'' having an `Adjusted Peak Performance' (`APP') exceeding 
1.0 Weighted TeraFLOPS (WT).
    (iii) 4E001-- ``Technology'' according to the General Technology 
Note for the ``development'' or ``production'' of any of the 
following equipment or ``software'': equipment controlled under ECCN 
4A001.a.2, ``digital computers'' having an `Adjusted Peak 
Performance' (`APP') exceeding 1.0 Weighted TeraFLOPS (WT), or 
``software'' controlled under the specific provisions of 4D001 
described in this Supplement.
* * * * *
    (7) * * *
    (v) 7D004.a to .d and .g.
* * * * *

    Dated: July 25, 2014.
Kevin J. Wolf,
Assistant Secretary for Export Administration.
[FR Doc. 2014-17975 Filed 8-1-14; 8:45 am]
BILLING CODE 3510-33-P