[Federal Register Volume 79, Number 118 (Thursday, June 19, 2014)]
[Rules and Regulations]
[Pages 35037-35041]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2014-13835]
[[Page 35037]]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2012-0415; Directorate Identifier 2008-SW-065-AD;
Amendment 39-17865; AD 2014-12-04]
RIN 2120-AA64
Airworthiness Directives; Bell Helicopter Textron, Inc. (BHTI)
Helicopters
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: We are superseding Airworthiness Directive (AD) 2003-01-04 for
BHTI Model 204B, 205A, 205A-1, 205B, and 212 helicopters. AD 2003-01-04
required inspecting the main rotor grip (grip) and reporting certain
inspection results to the FAA. AD 2003-01-04 also required performing
additional inspections, repair, or replacement depending on whether a
crack or delamination was found, and determining and recording the
hours time-in-service (TIS) and the engine start/stop cycles for each
grip on a component history card or equivalent record. This new AD
requires the same actions as AD 2003-01-04 but adds a retirement life
to certain grips and expands the applicability to include the Model 210
helicopter and additional part-numbered grips. This AD was prompted by
the discovery of additional cracked grips. We are issuing this AD to
prevent failure of a grip, separation of a main rotor blade, and
subsequent loss of control of the helicopter.
DATES: This AD is effective July 24, 2014.
The Director of the Federal Register approved the incorporation by
reference of a certain publication listed in this AD as of January 30,
2003 (68 FR 1955, January 15, 2003).
ADDRESSES: For service information identified in this AD, contact BHTI,
P.O. Box 482, Fort Worth, TX 76101, telephone (817) 280-3391, fax (817)
280-6466, or at http://www.bellcustomer.com/files/. You may view this
referenced service information at the FAA, Office of the Regional
Counsel, Southwest Region, 2601 Meacham Blvd., Room 663, Fort Worth,
Texas 76137.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov or in person at the Docket Operations Office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this AD, any incorporated-by-reference
service information, the economic evaluation, any comments received,
and other information. The street address for the Docket Operations
Office (phone: 800-647-5527) is U.S. Department of Transportation,
Docket Operations Office, M-30, West Building Ground Floor, Room W12-
140, 1200 New Jersey Avenue SE., Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Michael Kohner, Aviation Safety
Engineer, Rotorcraft Certification Office, 2601 Meacham Blvd., Fort
Worth, Texas 76137, telephone (817) 222-5170, fax (817) 222-5783, email
[email protected] or [email protected].
SUPPLEMENTARY INFORMATION:
Discussion
We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR
part 39 to supersede AD 2003-01-04, Amendment 39-13015 (68 FR 1955,
January 15, 2003) (AD 2003-01-04). AD 2003-01-04 applied to certain
BHTI Model 204B, 205A, 205A-1, 205B, and 212 helicopters. AD 2003-01-04
required inspecting each grip, reporting certain inspection results to
the FAA, and performing additional inspections, repair, or replacement
depending on whether a crack or delamination was found. AD 2003-01-04
also required determining and recording the hours TIS and the engine
start/stop cycles for each grip on a component history card or
equivalent record.
The NPRM published in the Federal Register on April 20, 2012 (77 FR
23638) and proposed to require the same actions as AD 2003-01-04 but
add a retirement life to certain grips and expand the applicability to
include the Model 210 helicopter and additional part-numbered grips.
Specifically, the NPRM proposed:
Within 10 hours TIS, determining and recording the hours
TIS and the engine start/stop cycles for each grip on a component
history card or equivalent record.
Within 10 hours TIS and thereafter at intervals not to
exceed 25 hours TIS, visually inspecting the exposed surfaces of the
upper and lower tangs of each grip for a crack, using a 10-power or
higher magnifying glass.
At specified intervals, depending on the hours TIS or the
engine start/stop cycles, conducting initial and repetitive ultrasonic
(UT) inspections of each grip.
At intervals not to exceed 1,200 hours TIS or 24 months,
whichever occurs first, inspecting each buffer pad on the tang inner
surfaces for delamination, and removing the buffer pad and inspecting
the grip surface for corrosion and other damage if there is
delamination.
Within 2,400 hours TIS or at the next overhaul of the main
rotor hub, whichever occurs first, and thereafter at intervals not to
exceed 2,400 hours TIS, inspecting the surface of each affected grip
for corrosion or other damage and conducting a fluorescent penetrant
inspection of the grip for a crack.
Before further flight, repairing or replacing any grip
that has a crack, corrosion, or other damage.
Before further flight, removing any grip, part number (P/
N) 204-011-121-009 or ASI-4011-121-9, that has 15,000 or more hours
TIS; and removing any grip, P/N 204-011-121-121, that has 25,000 or
more hours TIS.
Establishing a new retirement life of 15,000 hours TIS for
grip, P/N 204-011-121-009 or ASI-4011-121-9, and 25,000 hours TIS for
grip, P/N 204-011-121-121.
This AD was prompted by the discovery of additional cracked grips.
We are issuing this AD to prevent failure of a grip, separation of a
main rotor blade, and subsequent loss of control of the helicopter.
Comments
After our NPRM (77 FR 23638, April 20, 2012) was published, we
received comments from six commenters.
Request
Alpine Helicopters Ltd., Eagle Copters Ltd., Wildcat Helicopters,
Inc., and two commenters from BHTI disagreed with the proposed life
limit because the inspection procedures are sufficient to detect a
crack in the grips.
We do not agree. The life limits for the -009 and -121 grips are
necessary to correct the unsafe condition. While the UT inspections of
the grips have increased the level of safety because grips have been
discovered with a crack using this technique, we disagree with relying
solely on the repetitive UT inspections of the lower grip tang without
establishing a retirement life. Using a safety-by-inspection approach
for a critical component has been shown to have an inherent amount of
risk. Early failures of these grips, which have not been attributed to
mechanical or other damage, have indicated the need to establish a
retirement life to avoid possible cracking in the future.
Eagle Copters, Ltd., and Wildcat Helicopters, Inc., requested that
we consider implementing shorter inspection intervals or a higher level
of
[[Page 35038]]
training and experience to complete the inspections.
We disagree because we do not believe shorter inspection intervals
or a higher level of training would provide an adequate long term
solution to correct the unsafe condition. The risk of the onset of
fatigue cracking in a grip from other than induced damage and its
subsequent failure continually increases the further the part's safe-
life (retirement life) is exceeded.
Eagle Copters Ltd., Wildcat Helicopters, Inc., Alpine Helicopters
Ltd., and one commenter from BHTI expressed concern that a sufficient
number of replacement parts will not be available. Eagle Copters Ltd.,
and Wildcat Helicopters, Inc., specifically requested that affected
grips with no known time-in-service be allowed to remain in service for
up to 3 years.
We disagree. While every effort is made to avoid grounding of
aircraft, the FAA must nonetheless take action to correct an unsafe
condition, such as the one in this case.
Eagle Copters, Ltd., and Wildcat Helicopters Inc., requested that
we increase the retirement life of the grips. Eagle Copters, Inc.
requested that we increase the retirement life of the -009 grip from
15,000 hours TIS to 25,000 hours TIS, because a life limit of 15,000
hours TIS is not justified based on service history of the -009 grip.
Wildcat Helicopters, Inc., requested that we increase the retirement
life of the -009 and -121 grip to 30,000 hours TIS.
Similarly, Satria Air Service (SAS) requested that we conduct
further research on these failures and questioned our calculation of
the proposed life limits. SAS stated that the proposed retirement life
for the -121 grip is higher than the -009 grip even though the -121
grip is more prone to failure, which would indicate the need for a
lower retirement life. SAS further stated that in a recent failure, the
-121 grip had only accumulated 4,900 hours TIS, which is less than the
proposed retirement life of 25,000 hours TIS. SAS also noted the 150
hour TIS repetitive inspection interval of the -121 grip is lower than
the 400 hour TIS repetitive inspection interval for the -009 grip,
which indicates there is a reason for the shorter inspection interval
on the -121 grip.
We disagree with the request to increase the life limits of the
grips, as this would not provide an acceptable level of safety in
addressing the unsafe condition. The retirement lives for the -009 and
-121 grips were determined using a crack initiation methodology (e.g.,
using the S-N curves and Miner's Rule). This method accounts for damage
induced by fatigue loading but does not account for flaws and defects
due to manufacturing or in-service conditions. The apparent discrepancy
raised by the commenters can be explained by different sets of material
properties being used to determine the retirement lives and inspection
intervals for the grips. The material for the -121 grips was originally
changed because of stress corrosion cracking that was occurring in the
barrel of the -009 grips. Different materials will have varying levels
for susceptibility to different types of damage. A more ``failure
prone'' component may not necessarily warrant a lower retirement life.
Early failures can occur from a crack initiating from damage induced by
other than fatigue. Several of the failed -121 grips were also found
with cracking at multiple origins. This would explain the apparent
discrepancy of -121 grips having a shorter interval for UT inspections
but yet a higher retirement life.
SAS requested that we change the proposed method for calculating
the life of a grip with an unknown total of hours TIS, as it is
impractical because grips are often in storage as spare parts or as a
subcomponent of a main rotor hub assembly which may have been out of
service. The commenter suggested assigning a fixed high time to a time
since new unknown part, to allow an operator to plan for replacement at
the next scheduled overhaul.
We partially agree. We agree that establishing a realistic in-
service life for a component which is currently unlimited and only
required to be replaced when damaged or corroded beyond repair is
difficult. We disagree that the proposed method should be changed,
however, because it is the same method as that in AD 2003-01-04 (68 FR
1955, January 15, 2003); only the number of hours TIS have been revised
with our proposal. As far as allowing an operator time to plan for
replacing a part, the proposed life limits are based on the actions we
determine necessary to address the unsafe condition.
FAA's Determination
We have reviewed the relevant information, considered the comments
received, and determined that an unsafe condition exists and is likely
to exist or develop on other helicopters of these same type designs and
that air safety and the public interest require adopting the AD
requirements as proposed except for minor editorial changes. In
paragraph (a) of this AD, the reference to ``the following model
helicopters'' has been changed to reference ``the model helicopters
listed in Table 1 to Paragraph (a) of this AD'' instead. ``Figure 1 to
Paragraph (f)'' has been changed to reference ``Figure 1 to Paragraphs
(f)(2)(ii) and (f)(4)(ii).'' ``Table 2 to Paragraph (f)'' has been
changed to reference ``Table 2 to Paragraph (f)(3).'' ``Note 1 to
Paragraph (f)'' has been changed to reference ``Note 1 to Paragraph
(f)(3).'' ``Note 2 to Paragraph (f)'' has been changed to reference
``Note 2 to Paragraph (f)(4).'' These minor editorial changes are
consistent with the intent of the proposals in the NPRM (77 FR 23638,
April 20, 2012) and will not increase the economic burden on any
operator nor increase the scope of this AD.
Related Service Information
We reviewed the following BHTI service information:
Operations Safety Notices 204-85-6, 205-85-9, and 212-85-
13, all dated November 14, 1985, (one notice with 3 identification
numbers), which describe a grip with a crack in the lower tang that was
returned by an operator;
Alert Service Bulletin (ASB) No. 212-94-92, Revision A,
dated March 13, 1995, which describes procedures for inspection and
overhaul requirements of certain grips;
ASB No. 204-02-58, dated November 26, 2002; ASB No. 205-
02-88, dated November 26, 2002; and ASB No. 210-08-02, dated September
10, 2008. These ASBs specify a UT inspection of certain grips;
ASB No. 205B-02-39, Revision B, dated November 22, 2002,
and ASB No. 212-02-116, Revision A, dated October 30, 2002, which
specify a UT inspection of certain grips and include the Nondestructive
Inspection Procedure, Log No. 00-340, Revision E, dated April 9, 2002;
and
Information Letter 204-08-23, 205-08-38, 205B-08-21, and
212-08-62, Revision A, dated July 23, 2008 (one letter issued with 4
identification numbers), which describes a new, improved replacement
grip, P/N 204-011-121-125, that would not require the repetitive UT
inspections and would have a retirement life of 25,000 hours TIS or a
500,000 Retirement Index Number (RIN), whichever comes first.
Differences Between This AD and the Service Information
This AD requires life limits for grip P/Ns 204-011-121-009, 204-
011-121-121, and ASI-4011-121-9. The manufacturer's service bulletins
do not specify a service life for these grips. Also, this AD applies to
grip P/N ASI-4011-121-9, which is produced under an FAA parts
manufacturing approval,
[[Page 35039]]
and the manufacturer's service bulletins do not address this particular
grip.
Costs of Compliance
We estimate that this AD will affect 700 helicopters of U.S.
registry, and it will take approximately 7 work hours to create and
maintain the records, 6.25 work hours to conduct the inspections, and
20 work hours to replace a set of grips at an average labor rate of $85
per work hour. Required parts cost approximately $56,385 for a
replacement set of grips. Based on these figures, we estimate the total
cost impact of this AD on U.S. operators to be $6,596,875 for the
entire fleet, assuming the grip set (2 grips) is replaced on 100
helicopters.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
This AD will not have federalism implications under Executive Order
13132. This AD will not have a substantial direct effect on the States,
on the relationship between the national government and the States, or
on the distribution of power and responsibilities among the various
levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979);
(3) Will not affect intrastate aviation in Alaska to the extent
that it justifies making a regulatory distinction; and
(4) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act. We prepared an economic evaluation
of the estimated costs to comply with this AD and placed it in the AD
docket.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by removing Airworthiness Directive (AD)
2003-01-04 (68 FR 1955, January 15, 2003), and adding the following new
AD:
2014-12-04 Bell Helicopter Textron, Inc. (BHTI): Amendment 39-17865;
Docket No. FAA-2012-0415; Directorate Identifier 2008-SW-065-AD.
(a) Applicability
This AD applies to the model helicopters listed in Table 1 to
Paragraph (a) of this AD with the listed part-numbered main rotor
grips installed, certificated in any category:
Table 1 to Paragraph (a)--Helicopter Model and Main Rotor Grip (Grip)
Part Numbers Affected
------------------------------------------------------------------------
With the following grip part number
Model (P/N)
------------------------------------------------------------------------
204B.............................. 204-011-121-005 if the grip was ever
installed on a Model 205B
helicopter.
204B, 205A, and 205A-1............ 204-011-121-009, -117, -121 or ASI-
4011-121-9.
205A and 205A-1................... 204-011-121-005 or -113 if the grip
was ever installed on a Model 205B
helicopter.
205B.............................. 204-011-121-005, -009, -113, -117,
or -121.
210............................... 204-011-121-009 or -121.
212............................... 204-011-121-009, -121, or ASI-4011-
121-9.
------------------------------------------------------------------------
(b) Unsafe Condition
This AD defines the unsafe condition as a crack in the main
rotor grip (grip), which could result in failure of a grip,
separation of a main rotor blade, and subsequent loss of control of
the helicopter.
(c) Affected AD
This AD supersedes AD 2003-01-04, Amendment 39-13015 (68 FR
1955, January 15, 2003).
(d) Effective Date
This AD becomes effective July 24, 2014.
(e) Compliance
You are responsible for performing each action required by this
AD within the specified compliance time unless it has already been
accomplished prior to that time.
(f) Required Actions
(1) Within 10 hours time-in-service (TIS), create a component
history card or equivalent record and determine and record the total
hours TIS for each grip. If the total hours TIS cannot be determined
from the helicopter records, assume and record 50 hours TIS for each
month for which the hours cannot be determined. Continue to count
and record the hours TIS and begin to count and record the number of
times the helicopter engine(s) are started (engine start/stop
cycles).
(2) Within 10 hours TIS, and thereafter at intervals not to
exceed 25 hours TIS, without removing the main rotor blades:
(i) Clean the exposed surfaces of the upper and lower tangs of
each grip with denatured alcohol, and wipe dry.
(ii) Using a 10-power or higher magnifying glass, visually
inspect the exposed surfaces of the upper and lower tangs of each
grip for a crack. Pay particular attention to the lower surface of
each lower grip tang from the main rotor blade bolt-bushing flange
to the leading and trailing edge of each grip tang as depicted in
Figure 1 to Paragraphs (f)(2)(ii) and (f)(4)(ii) of this AD.
[[Page 35040]]
[GRAPHIC] [TIFF OMITTED] TR19JN14.000
(3) At the intervals shown in Table 2 to Paragraph (f)(3) of
this AD, ultrasonic (UT) inspect each grip in accordance with the
Bell Helicopter Textron Nondestructive Inspection Procedure, Log No.
00-340, Revision E, dated April 9, 2002. The UT inspection of the
grip must be performed by a Non-Destructive Testing (NDT) UT Level I
Special, Level II, or Level III inspector who is qualified under the
guidelines established by MIL-STD-410E, ATA Specification 105, AIA-
NAS-410, or an FAA-accepted equivalent for qualification standards
of NDT Inspection/Evaluation Personnel.
Table 2 to Paragraph (f)(3)--Ultrasonic Inspection Intervals
----------------------------------------------------------------------------------------------------------------
Thereafter, at intervals not to
Within 30 days, exceed the following hours TIS or
or the following engine start/stop cycles, whichever
UT inspect grip, P/N: hours TIS for the occurs first:
grip, whichever -------------------------------------
occurs later: Engine start/stop
Hours TIS cycles
----------------------------------------------------------------------------------------------------------------
204-011-121-009 or ASI-4011-121-9...................... 4,000 400 1,600
204-011-121-121........................................ 500 150 600
204-011-121-005 or [dash]113, if the grip was EVER 4,000 400 1,600
installed on a Model 205B helicopter..................
204-011-121-117, if the grip was NEVER installed on a 4,000 150 600
Model 205B helicopter.................................
204-011-121-117, if the grip was EVER installed on a 500 150 600
Model 205B helicopter.................................
----------------------------------------------------------------------------------------------------------------
Note 1 to Paragraph (f)(3) of this AD: You can find the
Nondestructive Inspection Procedure attached to BHTI Alert Service
Bulletin (ASB) No. 205B-02-39, Revision B, dated November 22, 2002,
or BHTI ASB No. 212 02-116, Revision A, dated October 30, 2002.
(4) At intervals not to exceed 1,200 hours TIS or 24 months,
whichever occurs first:
(i) Remove each main rotor blade, and
[[Page 35041]]
(ii) Inspect each grip buffer pad on the inner surfaces of each
grip tang for delamination as depicted in Figure 1 to Paragraphs
(f)(2)(ii) and (f)(4)(ii) of this AD. If there is any delamination,
remove the buffer pad and inspect the grip surface for corrosion or
other damage.
Note 2 to Paragraph (f)(4) of this AD: This inspection interval
coincides with the main rotor tension-torsion strap replacement
times.
(5) Within 2,400 hours TIS, or at the next overhaul of the main
rotor hub, whichever occurs first, and thereafter at intervals not
to exceed 2,400 hours TIS:
(i) Remove each main rotor blade.
(ii) Remove each grip buffer pad (if installed) from the inner
surfaces of each grip tang.
(iii) Visually inspect the grip tang surfaces for corrosion or
other damage.
(iv) Fluorescent-penetrant inspect the grip for a crack, paying
particular attention to the upper and lower grip tangs. When
inspecting any grip, P/N 204-011-121-005, -009, -113, or ASI-4011-
121-9, pay particular attention to the leading and trailing edges of
the grip barrel.
(6) Before further flight:
(i) Replace any cracked grip with an airworthy grip.
(ii) Replace any grip with any corrosion or other damage with an
airworthy grip, or repair the grip if the corrosion or other damage
is within maximum repair damage limitations.
(iii) Replace any grip, P/N 204-011-121-009 or ASI-4011-121-9,
which has been in service for 15,000 or more hours TIS.
(iv) Replace any grip, P/N 204-011-121-121, which has been in
service for 25,000 or more hours TIS.
(7) Revise the Airworthiness Limitations sections of the
applicable maintenance manuals or the Instructions for Continued
Airworthiness (ICAs) by establishing a new retirement life of 15,000
hours TIS for grip P/N 204-011-121-009 or ASI-4011-121-9, and 25,000
hours TIS for grip P/N 204-011-121-121, by making pen and ink
changes or inserting a copy of this AD into the applicable
maintenance manual or ICAs.
(8) Record a 15,000 hours TIS life limit for each grip P/N 204-
011-121-009 or ASI-4011-121-9, and a 25,000 hours TIS life limit for
each grip P/N 204-011-121-121, on the applicable component history
card or equivalent record.
(g) Alternative Methods of Compliance (AMOCs)
(1) The Manager, Rotorcraft Certification Office, FAA, may
approve AMOCs for this AD. Send your proposal to: Michael Kohner,
Aviation Safety Engineer, Rotorcraft Certification Office, 2601
Meacham Blvd., Fort Worth, Texas 76137, telephone (817) 222-5170,
fax (817) 222-5783, email [email protected] or [email protected].
(2) For operations conducted under a Part 119 operating
certificate or under Part 91, Subpart K, we suggest that you notify
your principal inspector, or lacking a principal inspector, the
manager of the local flight standards district office or certificate
holding district office before operating any aircraft complying with
this AD through an AMOC.
(h) Additional Information
(1) BHTI ASB No. 212-94-92, Revision A, dated March 13, 1995;
BHTI ASB No. 212-02-116, Revision A, dated October 30, 2002; BHTI
205B-02-39, Revision B, dated November 22, 2002; BHTI ASB No. 204-
02-58 and ASB No. 205-02-88, both dated November 26, 2002; BHTI ASB
No. 210-08-02, dated September 10, 2008; BHTI Operations Safety
Notice 204-85-6, 205-85-9, and 212-85-13, all dated November 14,
1985; and BHTI Information Letter, 204-08-23, 205-08-38, 205B-08-21,
and 212-08-62, Revision A, dated July 23, 2008; none of which are
incorporated by reference, contain additional information about the
subject of this AD.
(2) For service information identified in this AD, contact BHTI,
P.O. Box 482, Fort Worth, TX 76101, telephone (817) 280-3391, fax
(817) 280-6466, or at http://www.bellcustomer.com/files/. You may
review copies of this information at the FAA, Office of the Regional
Counsel, Southwest Region, 2601 Meacham Blvd., Room 663, Fort Worth,
Texas 76137.
(i) Subject
Joint Aircraft Service Component (JASC) Code: 6220: Main Rotor
Head.
(j) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the service information listed
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless the AD specifies otherwise.
(3) The following service information was approved for IBR on
January 30, 2003 (68 FR 1955, January 15, 2003).
(i) Bell Helicopter Textron Nondestructive Inspection Procedure,
Log No. 00-340, Revision E, dated April 9, 2002.
(ii) Reserved.
(4) For Bell Helicopter Textron service information identified
in this AD, contact BHTI, P.O. Box 482, Fort Worth, TX 76101,
telephone (817) 280-3391, fax (817) 280-6466, or at http://www.bellcustomer.com/files/.
(5) You may view this service information that is incorporated
by reference at the FAA, Office of the Regional Counsel, Southwest
Region, 2601 Meacham Blvd., Room 663, Fort Worth, Texas 76137.
(6) You may also view this service information that is
incorporated by reference at the National Archives and Records
Administration (NARA). For information on the availability of this
material at NARA, call (202) 741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.
Issued in Fort Worth, Texas, on June 4, 2014.
Lance T. Gant,
Acting Directorate Manager, Rotorcraft Directorate, Aircraft
Certification Service.
[FR Doc. 2014-13835 Filed 6-18-14; 8:45 am]
BILLING CODE 4910-13-P