[Federal Register Volume 78, Number 240 (Friday, December 13, 2013)]
[Notices]
[Pages 75947-75948]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2013-29727]


-----------------------------------------------------------------------

DEPARTMENT OF LABOR

Office of the Secretary


Agency Information Collection Activities; Submission for OMB 
Review; Comment Request; Welding, Cutting, and Brazing Standard

ACTION: Notice.

-----------------------------------------------------------------------

SUMMARY: The Department of Labor (DOL) is submitting the Occupational 
Safety and Health Administration (OSHA) sponsored information 
collection request (ICR) titled, ``Welding, Cutting, and Brazing 
Standard,'' to the Office of Management and Budget (OMB) for review and 
approval for continued use, without change, in accordance with the 
Paperwork Reduction Act of 1995 (PRA), 44 U.S.C. 3501 et seq.

DATES: Submit comments on or before January 13, 2014.

ADDRESSES: A copy of this ICR with applicable supporting documentation; 
including a description of the likely respondents, proposed frequency 
of response, and estimated total burden may be obtained free of charge 
from the RegInfo.gov Web site at http://www.reginfo.gov/public/do/PRAViewICR?ref_nbr=201310-1218-002 (this link will only become active 
on the day following publication of this notice) or by contacting 
Michel Smyth by telephone at 202-693-4129 (this is not a toll-free 
number) or sending an email to [email protected].
    Submit comments about this request by mail or courier to the Office 
of Information and Regulatory Affairs, Attn: OMB Desk Officer for DOL-
OSHA, Office of Management and Budget, Room 10235, 725 17th Street NW., 
Washington, DC 20503; by Fax: 202-395-6881 (this is not a toll-free 
number); or by email: [email protected]. Commenters are 
encouraged, but not required, to send a courtesy copy of any comments 
by mail or courier to the U.S. Department of Labor-OASAM, Office of the 
Chief Information Officer, Attn: Departmental Information Compliance 
Management Program, Room N1301, 200 Constitution Avenue NW., 
Washington, DC 20210; or by email: [email protected].

FOR FURTHER INFORMATION CONTACT: Michel Smyth by telephone at 202-693-
4129 (this is not a toll-free number) or by email at [email protected].

    Authority: 44 U.S.C. 3507(a)(1)(D).

SUPPLEMENTARY INFORMATION: This ICR seeks to maintain PRA authorization 
for the information collection requirements contained in the Welding, 
Cutting, and Brazing Standard, regulations 29 CFR part 1910, subpart Q. 
More specifically, regulations 29 CFR 1910.255(e) requires that a 
periodic inspection of resistance welding equipment be made by 
qualified maintenance personnel and a certification record generated 
and maintained. The certification shall include the date of the 
inspection, the signature of the person who performed the inspection 
and the serial number, or other identifier, for the equipment 
inspected. The maintenance inspection ensures that welding equipment is 
in safe operating condition, while the maintenance record provides 
evidence that employers performed the required inspections. The 
Occupational Safety and Health Act authorizes this information 
collection. See 29 U.S.C. 657.
    This information collection is subject to the PRA. A Federal agency 
generally cannot conduct or sponsor a collection of information, and 
the public is generally not required to respond to an information 
collection, unless it is approved by the OMB under the PRA and displays 
a currently valid OMB Control Number. In addition, notwithstanding any 
other provisions of law, no person shall generally be subject to 
penalty for failing to comply with a collection of information that 
does not display a valid Control Number. See 5 CFR 1320.5(a) and 
1320.6. The DOL obtains OMB approval for this information collection 
under Control Number 1218-0207.
    OMB authorization for an ICR cannot be for more than three (3) 
years without renewal, and the current approval for this collection is 
scheduled to expire on January 31, 2014. The DOL seeks to extend PRA 
authorization for this information collection for three (3) more years, 
without any change to existing requirements. The DOL notes that 
existing information collection requirements submitted to the OMB 
receive a month-to-month extension while they undergo review. For 
additional substantive information about this ICR, see the related 
notice published in the Federal Register on August 28, 2013.
    Interested parties are encouraged to send comments to the OMB, 
Office of Information and Regulatory Affairs at the address shown in 
the ADDRESSES section within 30 days of publication of this notice in 
the Federal Register. In order to help ensure appropriate 
consideration, comments should mention OMB Control Number 1218-0207. 
The OMB is particularly interested in comments that:

[[Page 75948]]

     Evaluate whether the proposed collection of information is 
necessary for the proper performance of the functions of the agency, 
including whether the information will have practical utility;
     Evaluate the accuracy of the agency's estimate of the 
burden of the proposed collection of information, including the 
validity of the methodology and assumptions used;
     Enhance the quality, utility, and clarity of the 
information to be collected; and
     Minimize the burden of the collection of information on 
those who are to respond, including through the use of appropriate 
automated, electronic, mechanical, or other technological collection 
techniques or other forms of information technology, e.g., permitting 
electronic submission of responses.
    Agency: DOL-OSHA.
    Title of Collection: Welding, Cutting, and Brazing Standard.
    OMB Control Number: 1218-0207.
    Affected Public: Private Sector--businesses or other for-profits.
    Total Estimated Number of Respondents: 20,094.
    Total Estimated Number of Responses: 80,657.
    Total Estimated Annual Burden Hours: 5,635.
    Total Estimated Annual Other Costs Burden: $0.

    Dated: December 6, 2013.
Michel Smyth,
Departmental Clearance Officer.
[FR Doc. 2013-29727 Filed 12-12-13; 8:45 am]
BILLING CODE 4510-26-P