[Federal Register Volume 78, Number 100 (Thursday, May 23, 2013)]
[Proposed Rules]
[Pages 30791-30793]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2013-12308]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2013-0450; Directorate Identifier 2013-CE-010-AD]
RIN 2120-AA64


Airworthiness Directives; Alexander Schleicher GmbH & Co. 
Segelflugzeugbau Sailplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for all 
Alexander Schleicher GmbH & Co. Segelflugzeugbau Models AS-K13, Ka2B, 
Ka 6, Ka 6 B, Ka 6 BR, Ka 6 C, Ka 6 CR, K7, K8, and K 8 B sailplanes 
that would supersede an existing AD. This proposed AD results from 
mandatory continuing airworthiness information (MCAI) originated by an 
aviation authority of another country to identify and correct an unsafe 
condition on an aviation product. The MCAI describes the unsafe 
condition as misalignment of the automatic elevator control connection. 
We are issuing this proposed AD to require actions to address the 
unsafe condition on these products.

DATES: We must receive comments on this proposed AD by July 8, 2013.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590, between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Alexander Schleicher GmbH & Co Segelflugzeugbau, Stra[szlig]e 1 D--
36163 Poppenhausen, Germany; phone: ++49 (0) 6658/89-0; fax: ++49 (0) 
6658/89-40; email: [email protected]; Internet: http://www.alexander-schleicher.de/. You may review copies of the referenced 
service information at the FAA, Small Airplane Directorate, 901 Locust, 
Kansas City, Missouri 64106. For information on the availability of 
this material at the FAA, call (816) 329-4148.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the regulatory 
evaluation, any comments received, and other information. The street 
address for the Docket Office (telephone (800) 647-5527) is in the 
ADDRESSES section. Comments will be available in the AD docket shortly 
after receipt.

FOR FURTHER INFORMATION CONTACT: Jim Rutherford, Aerospace Engineer, 
FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, 
Missouri 64106; telephone: (816) 329-4165; fax: (816) 329-4090; email: 
[email protected].

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2013-0450; 
Directorate Identifier 2013-CE-010-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to http://regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    On March 5, 1964, we issued AD 64-07-05, Amendment 701 (29 FR 3227, 
March 11, 1964). That AD required actions intended to address an unsafe 
condition on some of the products listed above.
    Since we issued AD 64-07-05, Amendment 701 (29 FR 3227, March 11, 
1964) the European Aviation Safety Agency (EASA), which is the 
Technical Agent for the Member States of the European Community, has 
issued a new AD to add additional sailplane models to the applicability 
and to add additional inspections of the elevator control connection. 
Alexander Schleicher GmbH & Co. Segelflugzeugbau has also issued 
revised service information to address the unsafe condition.
    The EASA has issued AD No. 2013-0091, dated April 12, 2013 
(referred to after this as ``the MCAI''), to correct an unsafe 
condition for the specified products. The MCAI states:

A recent report has been received concerning a problem with the 
elevator control during take-off of an ASK 13 sailplane. The results 
of the technical investigation revealed a misalignment in the 
automatic elevator control connection, presumably caused by an 
incorrect repair or damage at the tail-plane-area. In addition, 
similar elevator connection failure during early 1960's which led to 
the issuance of LBA LTM 4/62. However, LTM, 4/62 did not apply to 
ASK 13 and ASK 18 sailplanes coming later into production.

This condition, if not detected and corrected, could lead to failure 
of the automatic elevator control connection, possibly resulting in 
loss of control of the sailplane.

To address this unsafe condition, Alexander Schleicher GmbH issued a 
Technical Note (TN) (Ka 6 TN-Nr. 26; K 7 TN-Nr. 24; K 8 TN-Nr. 30; 
ASK 13 TN-Nr. 19; ASK 18 TN-Nr. 9) providing instructions for 
elevator control inspection and replacement and EASA issued AD 2012-
0246 to require accomplishment of those instructions.

Since that AD was issued, Alexander Schleicher GmbH issued a 
revision of TN (Ka 6 TN-Nr. 26; K 7 TN-Nr. 24; K 8 TN-Nr. 30; ASK 13 
TN-Nr. 19, ASK 18 TN-Nr. 9), dated 08 January 2013 to re-introduce a 
pushrod support modification for K 7 and K 8 sailplanes, previously 
required by LBA LTM 4/62, but no longer required by EASA AD 2012-
0246, which superseded the LBA LTM.

For the reasons described above, this AD retains the requirements of 
EASA AD 2012-0246, which is superseded, and additionally requires, 
for K 7 and K 8 sailplanes, verification of embodiment of pushrod 
support modification, and depending on finding, pushrod support 
modification.


[[Page 30792]]


You may obtain further information by examining the MCAI in the AD 
docket.

Relevant Service Information

    Alexander Schleicher GmbH & Co. Segelflugzeugbau has issued 
Technical Note for Ka 2 and Ka 2b--TM-Nr. 13, Ka 6--TM-Nr. 26, K 7--TM-
Nr. 24, K 8--TM-Nr. 30, ASK 13--TM-Nr. 19, ASK 18--TM-Nr. 9, Revision 
1, dated January 8, 2013. The actions described in this service 
information are intended to correct the unsafe condition identified in 
the MCAI.
    The service information issued by Alexander Schleicher GmbH & Co. 
Segelflugzeugbau referenced above contains German to English 
translation. On the document we received it cites the use of ``TM,'' 
which is an abbreviation for Technische Mitteilung. The English 
translation for Technische Mitteilung is Technical Note. EASA used the 
English translation in referencing the document from Alexander 
Schleicher GmbH & Co. Segelflugzeugbau, as stated in the Discussion 
section above.
    For enforceability purposes, we will cite references to the 
Alexander Schleicher GmbH & Co. Segelflugzeugbau service information as 
it appears on the document.

FAA's Determination and Requirements of the Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with this State of Design Authority, they 
have notified us of the unsafe condition described in the MCAI and 
service information referenced above. We are proposing this AD because 
we evaluated all information and determined the unsafe condition exists 
and is likely to exist or develop on other products of the same type 
design.

Costs of Compliance

    We estimate that this proposed AD will affect 127 products of U.S. 
registry. We also estimate that it would take about .5 work-hour per 
product to comply with the new inspection requirements of this proposed 
AD. The average labor rate is $85 per work-hour.
    Based on these figures, we estimate the cost of the initial 
inspection proposed in this AD on U.S. operators to be $5,397.50, or 
$42.50 per product.
    We have no way of determining the number of repetitive inspections 
an owner/operator will incur over the life of the sailplane.
    In addition, we estimate that any necessary follow-on actions would 
take about 1 work-hour and require parts costing $119, for a cost of 
$204 per product. We have no way of determining the number of products 
that may need these actions.
    We also estimate that it will take about 2 work-hours per product 
to comply with actions retained from AD 64-07-05, Amendment 701 (29 FR 
3227, March 11, 1964) for Models Ka2B, Ka 6, Ka 6 B, Ka 6 BR, Ka 6 C, 
Ka 6 CR, K7, K8, and K 8 B sailplanes in this proposed AD, which 
affects 112 products of U.S. registry, and may require parts costing 
$103, for a cost of $273 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by removing Amendment 701 (29 FR 3227, 
March 11, 1964), and adding the following new AD:

Alexander Schleicher GmbH & Co. Segelflugzeugbau: Docket No. FAA-
2013-0450; Directorate Identifier 2013-CE-010-AD.

(a) Comments Due Date

    We must receive comments by July 8, 2013.

(b) Affected ADs

    This AD supersedes AD 64-07-05, Amendment 701 (29 FR 3227; March 
11, 1964).

(c) Applicability

    This AD applies to Alexander Schleicher GmbH & Co. 
Segelflugzeugbau Models AS -K13, Ka2B, Ka 6, Ka 6 B, Ka 6 BR, Ka 6 
C, Ka 6 CR, K7, K8, and K 8 B sailplanes, all serial numbers, 
certificated in any category.

(d) Subject

    Air Transport Association of America (ATA) Code 27: Flight 
Controls.

(e) Reason

    This AD was prompted by mandatory continuing airworthiness 
information (MCAI) originated by an aviation authority of another 
country to identify and correct an unsafe condition on an aviation 
product. The MCAI describes the unsafe condition as misalignment of 
the automatic elevator control connection. The European Aviation 
Safety Agency (EASA) has issued a new AD to add additional sailplane 
models to the applicability and to add additional inspections of the 
elevator control connection. Alexander Schleicher GmbH & Co. 
Segelflugzeugbau has also issued revised service information to 
address the unsafe condition. We are issuing this AD to prevent 
failure of the automatic elevator control connection, which could 
result in loss of control.

(f) Actions and Compliance Retained From AD 64-07-05, Amendment 701 (29 
FR 3227, March 1, 1964)

    Unless already done, do the following actions specified in 
paragraphs (f)(1), (f)(2), and (f)(3) of this AD.

[[Page 30793]]

    (1) For Models Ka2B, Ka 6, Ka 6 B, Ka 6 BR, Ka 6 C, Ka 6 CR, K7, 
K8, and K 8 B: Unless already done, within the next 10 hours time-
in-service (TIS) after April 13, 1964 (the effective date retained 
from AD 64-07-05, Amendment 701 (29 FR 3227, March 1, 1964)), 
inspect the automatic elevator control rod for conformity following 
Alexander Schleicher Automatic Elevator Connection document, dated 
December 5, 1961.
    (2) For Models Ka2B, Ka 6, Ka 6 B, Ka 6 BR, Ka 6 C, Ka 6 CR, K7, 
K8, and K 8 B: If any discrepancy is found during the inspection 
required in paragraph (f)(1) of this AD, before further flight, make 
any necessary repairs or modification following Civil Aeronautics 
Manual (CAM) 18, dated February 11, 1936, which can be found at the 
following Web site: http://ntl1.specialcollection.net/scripts/ws.dll?websearch&site=dot_cams.
    (3) For Models Ka2B, K7, K8 and K 8 B: Unless already done, 
within the next 10 hours TIS after April 13, 1964 (the effective 
date retained from AD 64-07-05, Amendment 701 (29 FR 3227, March 1, 
1964)), install an additional push pull rod support. For Models 
Ka2B, follow Alexander Schleicher Modification No. 7, dated July 4, 
1962. For Models K7, follow Alexander Schleicher Modification No. 8, 
dated November 23, 1961. For Models K8, follow Alexander Schleicher 
Modification No. 7, dated November 24, 1961.

(g) New Actions and Compliance

    Unless already done, do the following actions specified in 
paragraphs (g)(1) and (g)(2) of this AD.
    (1) For all models: Within 90 days after the effective date of 
this AD and repetitively thereafter at intervals not to exceed 12 
months, inspect the elevator control rod in the tailplane following 
the Action section in Alexander Schleicher Technical Note for Ka 2 
and Ka 2b-TM-Nr. 13, Ka 6-TM-Nr. 26, K 7-TM-Nr. 24, K 8-TM-Nr. 30, 
ASK 13-TM-Nr. 19, ASK 18-TM-Nr. 9, Revision 1, dated January 8, 
2013.
    (2) For all models: During any inspection required in paragraph 
(g)(1) of this AD, if any bend and/or misaligned elevator control 
connection is detected, before further flight after the inspection, 
replace the elevator control connection with a serviceable part. Do 
the replacement following the Action section in Alexander Schleicher 
Technical Note for Ka 2 and Ka 2b-TM-Nr. 13, Ka 6-TM-Nr. 26, K 7-TM-
Nr. 24, K 8-TM-Nr. 30, ASK 13-TM-Nr. 19, ASK 18-TM-Nr. 9, Revision 
1, dated January 8, 2013.

(h) Credit for Actions Done Following Previous Service Information

    This AD provides credit for the initial inspection required in 
paragraph (g)(1) of this AD and any necessary replacement required 
in paragraph (g)(2) of this AD if already done before the effective 
date of this AD following the Action sections in Alexander 
Schleicher Technical Note for Ka 2 and Ka 2b-TM-Nr. 13, Ka 6-TM-Nr. 
26, K 7-TM-Nr. 24, K 8-TM-Nr. 30, ASK 13-TM-Nr. 19, ASK 18-TM-Nr. 9, 
dated August 30, 2012.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Standards Office, FAA, has the authority to approve AMOCs for this 
AD, if requested using the procedures found in 14 CFR 39.19. Send 
information to ATTN: Jim Rutherford, Aerospace Engineer, FAA, Small 
Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 
64106; telephone: (816) 329-4165; fax: (816) 329-4090; email: 
[email protected]. Before using any approved AMOC on any 
sailplane to which the AMOC applies, notify your appropriate 
principal inspector (PI) in the FAA Flight Standards District Office 
(FSDO), or lacking a PI, your local FSDO.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.

(j) Related Information

    Refer to MCAI European Aviation Safety Agency (EASA) AD No. 
2013-0091, dated April 12, 2013; Alexander Schleicher Automatic 
Elevator Connection document, dated December 5, 1961; Civil 
Aeronautics Manual (CAM) 18, dated February 11, 1936; Alexander 
Schleicher Modification No. 7 Glider Ka 2 and Ka 2B, L-140 and L-
203, dated July 4, 1962; Alexander Schleicher Modification No. 8 
Glider K 7 L-211 (US 7G3), dated November 23, 1961; Alexander 
Schleicher Modification No. 7 Glider K 8 L-216 (US 7G4), dated 
November 24, 1961; Alexander Schleicher Technische Mitteilungt 
f[uuml]r Technical Note for Ka 2 and Ka 2b-TM-Nr. 13, Ka 6-TM-Nr. 
26, K 7-TM-Nr. 24, K 8-TM-Nr. 30, ASK 13-TM-Nr. 19, ASK 18-TM-Nr. 9, 
dated August 30, 2012; and Alexander Schleicher Technische 
Mitteilungt f[uuml]r Technical Note for Ka 2 and Ka 2b-TM-Nr. 13, Ka 
6-TM-Nr. 26, K 7-TM-Nr. 24, K 8-TM-Nr. 30, ASK 13-TM-Nr. 19, ASK 18-
TM-Nr. 9, Revision 1, dated January 8, 2013, for related 
information. For service information related to this AD, contact 
Alexander Schleicher GmbH & Co Segelflugzeugbau, Stra[szlig]e 1 D-
36163 Poppenhausen, Germany; phone: ++49 (0) 6658/89-0, fax: +49 (0) 
6658/89-40, email: [email protected]; Internet: http://www.alexander-schleicher.de. You may review copies of the referenced 
service information at the FAA, Small Airplane Directorate, 901 
Locust, Kansas City, Missouri 64106. For information on the 
availability of this material at the FAA, call (816) 329-4148.

    Issued in Kansas City, Missouri, on May 17, 2013.
Earl Lawrence,
Manager, Small Airplane Directorate, Aircraft Certification Service.
[FR Doc. 2013-12308 Filed 5-22-13; 8:45 am]
BILLING CODE 4910-13-P