[Federal Register Volume 77, Number 163 (Wednesday, August 22, 2012)]
[Notices]
[Pages 50727-50728]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2012-20637]
-----------------------------------------------------------------------
NUCLEAR REGULATORY COMMISSION
[NRC-2012-0195]
Configuration Management Plans for Digital Computer Software Used
in Safety Systems of Nuclear Power Plants
AGENCY: Nuclear Regulatory Commission.
ACTION: Draft regulatory guide; request for comment.
-----------------------------------------------------------------------
SUMMARY: The U.S. Nuclear Regulatory Commission (NRC or the Commission)
is issuing for public comment draft regulatory guide (DG), DG-1206,
``Configuration Management Plan for Digital Computer Software Used in
Safety Systems of Nuclear Power Plants.'' The DG-1206 is proposed
Revision 1 of RG 1.169, dated September 1997. This revision endorses,
with clarifications, the enhanced consensus practices for planning
software configuration management (SCM) as described in the Institute
of Electrical and Electronics Engineers (IEEE) Standard 828-2005,
``IEEE Standard for Software Configuration Management Plans.''
DATES: Submit comments by November 23, 2012. Comments received after
this date will be considered if it is practical to do so, but the NRC
is able to ensure consideration only for comments received on or before
this date. Although a time limit is given, comments and suggestions in
connection with items for inclusion in guides currently being developed
or improvements in all published guides are encouraged at any time.
ADDRESSES: You may access information and comment submissions related
to this document, which the NRC possesses and are publicly available,
by searching on http://www.regulations.gov under Docket ID NRC-2012-
0195. You may submit comments by any of the following methods:
Federal Rulemaking Web Site: Go to http://www.regulations.gov and search for Docket ID NRC-2012-0195. Address
questions about NRC dockets to Carol Gallagher; telephone: 301-492-
3668; email: [email protected].
Mail comments to: Cindy Bladey, Chief, Rules,
Announcements, and Directives Branch (RADB), Office of Administration,
Mail Stop: TWB-05-B01M, U.S. Nuclear Regulatory Commission, Washington,
DC 20555-0001.
Fax comments to: RADB at 301-492-3446.
For additional direction on accessing information and submitting
comments, see ``Accessing Information and Submitting Comments'' in the
SUPPLEMENTARY INFORMATION section of this document.
FOR FURTHER INFORMATION CONTACT: Karl Sturzebecher, Office of Nuclear
Regulatory Research, U.S. Nuclear Regulatory Commission, Washington, DC
20555-0001; telephone: 301-251-7494 or email [email protected].
SUPPLEMENTARY INFORMATION:
I. Accessing Information and Submitting Comments
A. Accessing Information
Please refer to Docket ID NRC-2012-0195 when contacting the NRC
about the availability of information regarding this document. You may
access information related to this document, which the NRC possesses
and are publicly available, by any of the following methods:
Federal Rulemaking Web Site: Go to http://www.regulations.gov and search for Docket ID NRC-2012-0195.
NRC's Agencywide Documents Access and Management System
(ADAMS): You may access publicly available documents online in the NRC
Library at http://www.nrc.gov/reading-rm/adams.html. To begin the
search, select ``ADAMS Public Documents'' and then select ``Begin Web-
based ADAMS Search.'' For problems with ADAMS, please contact the NRC's
Public Document Room (PDR) reference staff at 1-800-397-4209, 301-415-
4737, or by email to [email protected]. The draft regulatory guide
is available electronically under ADAMS Accession Number ML103200044.
The regulatory analysis may be found in ADAMS under Accession Number
ML103200047.
Regulatory guides are not copyrighted, and NRC approval is not
required to reproduce them.
NRC's PDR: You may examine and purchase copies of public
documents at the NRC's PDR, Room O1-F21, One White Flint North, 11555
Rockville Pike, Rockville, Maryland 20852.
B. Submitting Comments
Please include Docket ID NRC-2012-0195 in the subject line of your
comment submission, in order to ensure that the NRC is able to make
your comment submission available to the public in this docket.
The NRC cautions you not to include identifying or contact
information in comment submissions that you do not want to be publicly
disclosed. The NRC posts all comment submissions at http://www.regulations.gov as well as enters the comment submissions into
[[Page 50728]]
ADAMS. The NRC does not edit comment submissions to remove identifying
or contact information.
If you are requesting or aggregating comments from other persons
for submission to the NRC, then you should inform those persons not to
include identifying or contact information in their comment submissions
that they do not want to be publicly disclosed. Your request should
state that the NRC will not edit comment submissions to remove such
information before making the comment submissions available to the
public or entering the comment submissions into ADAMS.
II. Further Information
The NRC is issuing for public comment a draft guide in the NRC's
``Regulatory Guide'' series. This series was developed to describe and
make available to the public such information as methods that are
acceptable to the NRC staff for implementing specific parts of the
NRC's regulations, techniques that the staff uses in evaluating
specific problems or postulated accidents, and data that the staff
needs in its review of applications for permits and licenses.
The draft regulatory guide entitled ``Configuration Management
Plans for Digital Computer Software Used in Safety Systems of Nuclear
Power Plants'' is temporarily identified by its task number, DG-1206.
The DG-1206 is proposed Revision 1 of RG 1.169, ``Configuration
Management Plans for Digital Computer Software Used in Safety Systems
of Nuclear Power Plants'' dated September 1997.
This RG endorses IEEE Std. 828-2005, ``IEEE Standard for Software
Configuration Management Plans,'' issued in 2005, with the exceptions
stated in the regulatory positions. IEEE Std. 828-2005 describes
methods acceptable to the NRC staff for use in complying with the NRC's
regulations for promoting high functional reliability and design
quality in software used in safety systems. In particular, the methods
are consistent with part 50 of Title 10 of the Code of Federal
Regulations (10 CFR), ``Domestic Licensing of Production and
Utilization Facilities,'' Appendix A, ``General Design Criteria for
Nuclear Power Plants,'' General Design Criterion 1, ``Quality Standards
and Records,'' which requires, in part, that the nuclear power unit
licensee maintain or control appropriate records of the design and
testing of structures, systems, and components important to safety
throughout the life of the unit.
This draft regulatory guide is part of a series of 6 complimentary
guides addressing the issue of digital software in nuclear power plant
applications. The following is a complete list of all 6 of the DGs:
1. DG-1267 is proposed revision 2 of RG 1.168, ``Verification,
Validation, Reviews, and Audits for Digital Computer Software used in
Safety Systems of Nuclear Power Plants.'' DG-1267 is available in ADAMS
at Accession number ML103160431;
2. DG-1206 is proposed revision 1 of RG 1.169, ``Configuration
Management Plans for Digital Computer Software used in Safety Systems
of Nuclear Power Plants.'' DG-1206 is available in ADAMS at Accession
number ML103200044;
3. DG-1207 is proposed revision 1 of RG 1.170, ``Software Unit
Testing for Digital Computer Software Used in Safety Systems of Nuclear
Power Plants.'' DG-1207 is available in ADAMS at Accession number
ML083370243;
4. DG-1208 is proposed revision 1 if RG 1.171, ``Software Unit
Testing for Digital Computer Software used in Safety Systems of Nuclear
Power Plants.'' DG-1208 is available in ADAMS at Accession number
ML103120751;
5. DG-1209 is proposed revision 1 of RG 1.172, ``Software
Requirement Specifications for Digital Computer Software and Complex
Electronics used in Safety Systems of Nuclear Power Plants.'' DG-1209
is available in ADAMS at Accession number ML103080963;
6. DG-1210 is proposed revision 1 of RG 1.173, ``Developing
Software Life-Cycle Processes for Digital Computer Software used in
Safety Systems of Nuclear Power Plants.'' DG-1210 is available in ADAMS
at Accession number ML103120727.
Dated at Rockville, Maryland, this 9th day of August 2012.
For the Nuclear Regulatory Commission.
Thomas H. Boyce,
Chief, Regulatory Guide Development Branch, Division of Engineering,
Office of Nuclear Regulatory Research.
[FR Doc. 2012-20637 Filed 8-21-12; 8:45 am]
BILLING CODE 7590-01-P