[Federal Register Volume 77, Number 124 (Wednesday, June 27, 2012)]
[Notices]
[Pages 38324-38336]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2012-15672]


-----------------------------------------------------------------------

DEPARTMENT OF LABOR

Mine Safety and Health Administration


Petitions for Modification of Application of Existing Mandatory 
Safety Standards

AGENCY: Mine Safety and Health Administration, Labor.

ACTION: Notice.

-----------------------------------------------------------------------

SUMMARY: Section 101(c) of the Federal Mine Safety and Health Act of 
1977 and 30 CFR Part 44 govern the application, processing, and 
disposition of petitions for modification. This notice is a summary of 
petitions for modification submitted to the Mine Safety and Health 
Administration (MSHA) by the parties listed below to modify the 
application of existing mandatory safety standards codified in Title 30 
of the Code of Federal Regulations.

DATES: All comments on the petitions must be received by the Office of 
Standards, Regulations and Variances on or before July 27, 2012.

ADDRESSES: You may submit your comments, identified by ``docket 
number'' on the subject line, by any of the following methods:
    1. Electronic Mail: [email protected]. Include the docket 
number of the petition in the subject line of the message.
    2. Facsimile: 202-693-9441.
    3. Regular Mail or Hand Delivery: MSHA, Office of Standards, 
Regulations and Variances, 1100 Wilson Boulevard, Room 2350, Arlington, 
Virginia 22209-3939, Attention: George F. Triebsch, Director, Office of 
Standards, Regulations and Variances. Persons delivering documents are 
required to check in at the receptionist's desk on the 21st floor. 
Individuals may inspect copies of the petitions and comments during 
normal business hours at the address listed above.
    MSHA will consider only comments postmarked by the U.S. Postal 
Service or proof of delivery from another delivery service such as UPS 
or Federal Express on or before the deadline for comments.

FOR FURTHER INFORMATION CONTACT: Barbara Barron, Office of Standards, 
Regulations and Variances at 202-693-9447 (Voice), 
[email protected] (Email), or 202-693-9441 (Facsimile). [These are 
not toll-free numbers.]

SUPPLEMENTARY INFORMATION:

I. Background

    Section 101(c) of the Federal Mine Safety and Health Act of 1977 
(Mine Act) allows the mine operator or representative of miners to file 
a petition to modify the application of any mandatory safety standard 
to a coal or other mine if the Secretary of Labor determines that:
    (1) An alternative method of achieving the result of such standard 
exists which will at all times guarantee no less than the same measure 
of

[[Page 38325]]

protection afforded the miners of such mine by such standard; or
    (2) That the application of such standard to such mine will result 
in a diminution of safety to the miners in such mine.
    In addition, the regulations at 30 CFR 44.10 and 44.11 establish 
the requirements and procedures for filing petitions for modification.

II. Petitions for Modification

    Docket Number: M-2012-096-C.
    Petitioner: Mountain Coal Company, LLC, P.O. Box 591, 5174 Highway 
133, Somerset, Colorado 81434.
    Mine: West Elk Mine, MSHA I.D. No. 05-03672, located in Gunnison 
County, Colorado.
    Regulation Affected: 30 CFR 75.503 (Permissible electric face 
equipment; maintenance) and 30 CFR 18.35(a)(5)(i) (Portable trailing 
cables and cords).
    Modification Request: The petitioner requests a modification of the 
Decision and Order for an existing petition for modification, docket 
number M-96-104-C issued on January 14, 1998. That petition was granted 
for a three-phase 995-volt continuous mining machine and several other 
pieces of equipment. The petitioner states that:
    (1) Several stipulations in the Decision and Order address the use 
of 2/0 trailing cable supplying power to the continuous miner.
    (2) With the purchase of Joy 12CM27 continuous miners, the power 
supply cable to these continuous miners is 4/0 rather than 2/0. Using 
the minimum amount of current available and having the instantaneous 
over-current protection set at 2,500 amps, the use of 1,100 feet of 4/0 
trailing cable does not compromise miner safety nor does it adversely 
impact electrical protection of the cable. Based on this information, 
the petitioner requests a modification of the existing petition for 
modification to allow the use of 1,100 feet of 4/0 trailing cable for 
the continuous miners.
    The petitioner asserts that with the terms and conditions of the 
Decision and Order, the use of 1,100 feet of 4/0 cable for the 
continuous miners will at all times guarantee no less than the same 
measure of protection afforded by the existing standard.
    Docket Number: M-2012-097-C.
    Petitioner: Consol Pennsylvania Coal Company, LLC, Three Gateway 
Center, Suite 1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-
1000.
    Mine: Bailey Mine, MSHA I.D. No. 36-07230, located in Greene 
County, Pennsylvania.
    Regulation Affected: 30 CFR 75.500(d) (Permissible electric 
equipment).
    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment in 
or inby the last open crosscut, including, but not limited to, portable 
battery-operated mine transits, total station surveying equipment, 
distance meters, and data loggers. The petitioner states that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance 
meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used in 
or inby the last open crosscut will be examined by surveying personnel 
prior to use to ensure the equipment is being maintained in a safe 
operating condition. These examinations will include the following 
steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.
    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment in or inby the last open 
crosscut.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn outby the last open crosscut.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air outby the last open crosscut.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards associated with the use of 
nonpermissible surveying equipment in areas where methane could be 
present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-098-C.
    Petitioner: Consol Pennsylvania Coal Company, LLC, Three Gateway 
Center, Suite 1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-
1000.
    Mine: Bailey Mine, MSHA I.D. No. 36-07230, located in Greene 
County, Pennsylvania.
    Regulation Affected: 30 CFR 75.507-1(a) (Electric equipment other 
than power-connection points; outby the last open crosscut; return air; 
permissibility requirements).
    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment in 
return airways, including, but not limited to, portable battery-
operated mine transits, total station surveying equipment, distance 
meters, and data loggers. The petitioner states that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of

[[Page 38326]]

the most practical and accurate surveying equipment is necessary.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance 
meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used in 
return airways will be examined by surveying personnel prior to use to 
ensure the equipment is being maintained in a safe operating condition. 
These examinations will include the following steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.
    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment in return airways.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn out of the return airways.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air out of the return.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards associated with the use of 
nonpermissible surveying equipment in areas where methane could be 
present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-099-C.
    Petitioner: Consol Pennsylvania Coal Company, LLC, Three Gateway 
Center, Suite 1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-
1000.
    Mine: Bailey Mine, MSHA I.D. No. 36-07230, located in Greene 
County, Pennsylvania.
    Regulation Affected: 30 CFR 75.1002(a) (Installation of electric 
equipment and conductors; permissibility).
    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment 
within 150 feet of pillar workings, including, but not limited to, 
portable battery-operated mine transits, total station surveying 
equipment, distance meters, and data loggers. The petitioner states 
that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary. To ensure the safety of the 
miners in active mines and to protect miners in future mines that may 
mine in close proximity to these same active mines, it is necessary to 
determine the exact location and extent of the mine workings.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance 
meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used 
within 150 feet of pillar workings will be examined by surveying 
personnel prior to use to ensure the equipment is being maintained in a 
safe operating condition. These examinations will include the following 
steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.
    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment within 150 feet of pillar 
workings.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn further than 150 feet from pillar workings.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air more than 150 feet from pillar workings.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards and

[[Page 38327]]

limitations associated with the use of nonpermissible surveying 
equipment in areas where methane could be present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-100-C.
    Petitioner: Consol Pennsylvania Coal Company, LLC, Three Gateway 
Center, Suite 1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-
1000.
    Mine: Enlow Fork Mine, MSHA I.D. No. 36-07416, located in 
Washington County, Pennsylvania.
    Regulation Affected: 30 CFR 75.500(d) (Permissible electric 
equipment).
    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment in 
or inby the last open crosscut, including, but not limited to, portable 
battery-operated mine transits, total station surveying equipment, 
distance meters, and data loggers. The petitioner states that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard: (a) Nonpermissible electronic surveying equipment will be 
used when equivalent permissible electronic surveying equipment is not 
available. Such nonpermissible surveying equipment includes portable 
battery-operated total station surveying equipment, mine transits, 
distance meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used in 
or inby the last open crosscut will be examined by surveying personnel 
prior to use to ensure the equipment is being maintained in a safe 
operating condition. These examinations will include the following 
steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.
    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment in or inby the last open 
crosscut.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn outby the last open crosscut.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air outby the last open crosscut.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards associated with the use of 
nonpermissible surveying equipment in areas where methane could be 
present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-101-C.
    Petitioner: Consol Pennsylvania Coal Company, LLC, Three Gateway 
Center, Suite 1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-
1000.
    Mine: Enlow Fork Mine, MSHA I.D. No. 36-07416, located in 
Washington County, Pennsylvania.
    Regulation Affected: 30 CFR 75.507-1(a) (Electric equipment other 
than power-connection points; outby the last open crosscut; return air; 
permissibility requirements). Modification Request: The petitioner 
requests a modification of the existing standard to permit an 
alternative method of compliance to permit the use of battery-powered 
nonpermissible surveying equipment in return airways, including, but 
not limited to, portable battery-operated mine transits, total station 
surveying equipment, distance meters, and data loggers. The petitioner 
states that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance 
meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used in 
return airways will be examined by surveying personnel prior to use to 
ensure the equipment is being maintained in a safe operating condition. 
These examinations will include the following steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.

[[Page 38328]]

    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment in return airways.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn out of the return airways.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air out of the return.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards associated with the use of 
nonpermissible surveying equipment in areas where methane could be 
present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-102-C.
    Petitioner: Consol Pennsylvania Coal Company, LLC, Three Gateway 
Center, Suite 1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-
1000.
    Mine: Enlow Fork Mine, MSHA I.D. No. 36-07416, located in 
Washington County, Pennsylvania.
    Regulation Affected: 30 CFR 75.1002(a) (Installation of electric 
equipment and conductors; permissibility).
    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment 
within 150 feet of pillar workings, including, but not limited to, 
portable battery-operated mine transits, total station surveying 
equipment, distance meters, and data loggers. The petitioner states 
that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary. To ensure the safety of the 
miners in active mines and to protect miners in future mines that may 
mine in close proximity to these same active mines, it is necessary to 
determine the exact location and extent of the mine workings.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance 
meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used 
within 150 feet of pillar workings will be examined by surveying 
personnel prior to use to ensure the equipment is being maintained in a 
safe operating condition. These examinations will include the following 
steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.
    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment within 150 feet of pillar 
workings.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn further than 150 feet from pillar workings.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air more than 150 feet from pillar workings.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards and limitations associated 
with the use of nonpermissible surveying equipment in areas where 
methane could be present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-103-C.
    Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite 
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
    Mine: Alma No. 1 Deep Mine, MSHA I.D. No. 46-09277, located in 
Mingo County, West Virginia.
    Regulation Affected: 30 CFR 75.500(d) (Permissible electric 
equipment).

[[Page 38329]]

    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment in 
or inby the last open crosscut, including, but not limited to, portable 
battery-operated mine transits, total station surveying equipment, 
distance meters, and data loggers. The petitioner states that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance 
meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used in 
or inby the last open crosscut will be examined by surveying personnel 
prior to use to ensure the equipment is being maintained in a safe 
operating condition. These examinations will include the following 
steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.
    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment in or inby the last open 
crosscut.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn outby the last open crosscut.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air outby the last open crosscut.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards associated with the use of 
nonpermissible surveying equipment in areas where methane could be 
present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-104-C.
    Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite 
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
    Mine: Alma No. 1 Deep Mine, MSHA I.D. No. 46-09277, located in 
Mingo County, West Virginia.
    Regulation Affected: 30 CFR 75.507-1(a) (Electric equipment other 
than power-connection points; outby the last open crosscut; return air; 
permissibility requirements).
    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment in 
return airways, including, but not limited to, portable battery-
operated mine transits, total station surveying equipment, distance 
meters, and data loggers. The petitioner states that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance 
meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used in 
return airways will be examined by surveying personnel prior to use to 
ensure the equipment is being maintained in a safe operating condition. 
These examinations will include the following steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.
    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment in return airways.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn out of the return airways.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper

[[Page 38330]]

operating condition as defined in 30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air out of the return.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards associated with the use of 
nonpermissible surveying equipment in areas where methane could be 
present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-105-C.
    Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite 
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
    Mine: Alma No. 1 Deep Mine, MSHA I.D. No. 46-09277, located in 
Mingo County, West Virginia.
    Regulation Affected: 30 CFR 75.1002(a) (Installation of electric 
equipment and conductors; permissibility).
    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment 
within 150 feet of pillar workings, including, but not limited to, 
portable battery-operated mine transits, total station surveying 
equipment, distance meters, and data loggers. The petitioner states 
that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary. To ensure the safety of the 
miners in active mines and to protect miners in future mines that may 
mine in close proximity to these same active mines, it is necessary to 
determine the exact location and extent of the mine workings.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance 
meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used 
within 150 feet of pillar workings will be examined by surveying 
personnel prior to use to ensure the equipment is being maintained in a 
safe operating condition. These examinations will include the following 
steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.
    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment within 150 feet of pillar 
workings.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn further than 150 feet from pillar workings.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air more than 150 feet from pillar workings.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards and limitations associated 
with the use of nonpermissible surveying equipment in areas where 
methane could be present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-106-C.
    Petitioner: Consolidation Coal Company, Three Gateway Center, Suite 
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
    Mine: Buchanan 1 Mine, MSHA I.D. No. 44-04856, located in 
Buchanan County, Virginia.
    Regulation Affected: 30 CFR 75.500(d) (Permissible electric 
equipment).
    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment in 
or inby the last open crosscut, including, but not limited to, portable 
battery-operated mine transits, total station surveying equipment, 
distance meters, and data loggers. The petitioner states that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying

[[Page 38331]]

equipment, mine transits, distance meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used in 
or inby the last open crosscut will be examined by surveying personnel 
prior to use to ensure the equipment is being maintained in a safe 
operating condition. These examinations will include the following 
steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.
    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment in or inby the last open 
crosscut.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn outby the last open crosscut.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air outby the last open crosscut.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards associated with the use of 
nonpermissible surveying equipment in areas where methane could be 
present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-107-C.
    Petitioner: Consolidation Coal Company, Three Gateway Center, Suite 
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
    Mine: Buchanan 1 Mine, MSHA I.D. No. 44-04856, located in 
Buchanan County, Virginia.
    Regulation Affected: 30 CFR 75.507-1(a) (Electric equipment other 
than power-connection points; outby the last open crosscut; return air; 
permissibility requirements).
    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment in 
return airways, including, but not limited to, portable battery-
operated mine transits, total station surveying equipment, distance 
meters, and data loggers. The petitioner states that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance 
meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used in 
return airways will be examined by surveying personnel prior to use to 
ensure the equipment is being maintained in a safe operating condition. 
These examinations will include the following steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.
    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment in return airways.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn out of the return airways.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air out of the return.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards associated with the use of 
nonpermissible surveying equipment in areas where methane could be 
present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-108-C.

[[Page 38332]]

    Petitioner: Consolidation Coal Company, Three Gateway Center, Suite 
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
    Mine: Buchanan 1 Mine, MSHA I.D. No. 44-04856, located in 
Buchanan County, Virginia.
    Regulation Affected: 30 CFR 75.1002(a) (Installation of electric 
equipment and conductors; permissibility).
    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment 
within 150 feet of pillar workings, including, but not limited to, 
portable battery-operated mine transits, total station surveying 
equipment, distance meters, and data loggers. The petitioner states 
that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary. To ensure the safety of the 
miners in active mines and to protect miners in future mines that may 
mine in close proximity to these same active mines, it is necessary to 
determine the exact location and extent of the mine workings.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance 
meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used 
within 150 feet of pillar workings will be examined by surveying 
personnel prior to use to ensure the equipment is being maintained in a 
safe operating condition. These examinations will include the following 
steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.
    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment within 150 feet of pillar 
workings.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn further than 150 feet from pillar workings.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air more than 150 feet from pillar workings.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards and limitations associated 
with the use of nonpermissible surveying equipment in areas where 
methane could be present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-109-C.
    Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite 
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
    Mine: MT-41 (Bronzite II) Mine, MSHA I.D. No. 46-09307, located in 
Mingo County, West Virginia.
    Regulation Affected: 30 CFR 75.500(d) (Permissible electric 
equipment).
    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment in 
or inby the last open crosscut, including, but not limited to, portable 
battery-operated mine transits, total station surveying equipment, 
distance meters, and data loggers. The petitioner states that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying
    equipment, mine transits, distance meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used in 
or inby the last open crosscut will be examined by surveying personnel 
prior to use to ensure the equipment is being maintained in a safe 
operating condition. These examinations will include the following 
steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.
    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before

[[Page 38333]]

and during the use of nonpermissible surveying equipment in or inby the 
last open crosscut.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn outby the last open crosscut.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air outby the last open crosscut.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards associated with the use of 
nonpermissible surveying equipment in areas where methane could be 
present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-110-C.
    Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite 
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
    Mine: MT-41 (Bronzite II) Mine, MSHA I.D. No. 46-09307, located in 
Mingo County, West Virginia.
    Regulation Affected: 30 CFR 75.507-1(a) (Electric equipment other 
than power-connection points; outby the last open crosscut; return air; 
permissibility requirements).
    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment in 
return airways, including, but not limited to, portable battery-
operated mine transits, total station surveying equipment, distance 
meters, and data loggers. The petitioner states that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance 
meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used in 
return airways or inby the last open crosscut will be examined by 
surveying personnel prior to use to ensure the equipment is being 
maintained in a safe operating condition. These examinations will 
include the following steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.
    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment in return airways.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn out of the return airways.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air out of the return.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards associated with the use of 
nonpermissible surveying equipment in areas where methane could be 
present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-111-C.
    Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite 
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
    Mine: MT-41 (Bronzite II) Mine), MSHA I.D. No. 46-09307, located in 
Mingo County, West Virginia.
    Regulation Affected: 30 CFR 75.1002(a) (Installation of electric 
equipment and conductors; permissibility).
    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment 
within 150 feet of pillar workings, including, but not limited to, 
portable battery-operated mine transits, total station surveying 
equipment, distance meters, and data loggers. The petitioner states 
that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary. To ensure the safety of the 
miners in active mines and to protect miners in future mines that may 
mine in close proximity to these same active mines, it is necessary to 
determine the exact

[[Page 38334]]

location and extent of the mine workings.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance 
meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used 
within 150 feet of pillar workings will be examined by surveying 
personnel prior to use to ensure the equipment is being maintained in a 
safe operating condition. These examinations will include the following 
steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.
    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment within 150 feet of pillar 
workings.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn further than 150 feet from pillar workings.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air more than 150 feet from pillar workings.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards and limitations associated 
with the use of nonpermissible surveying equipment in areas where 
methane could be present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-112-C.
    Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite 
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
    Mine: Bronzite III Mine, MSHA I.D. No. 46-05978, located in Mingo 
County, West Virginia.
    Regulation Affected: 30 CFR 75.500(d) (Permissible electric 
equipment).
    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment in 
or inby the last open crosscut, including, but not limited to, portable 
battery-operated mine transits, total station surveying equipment, 
distance meters, and data loggers. The petitioner states that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance 
meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used in 
or inby the last open crosscut will be examined by surveying personnel 
prior to use to ensure the equipment is being maintained in a safe 
operating condition. These examinations will include the following 
steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.
    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment in or inby the last open 
crosscut.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn outby the last open crosscut.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air outby the last open crosscut.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards associated with the use of 
nonpermissible surveying equipment in areas where methane could be 
present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in

[[Page 38335]]

compliance with all the terms and conditions in this petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-113-C.
    Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite 
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
    Mine: Bronzite III, MSHA I.D. No. 46-05978, located in Mingo 
County, West Virginia.
    Regulation Affected: 30 CFR 75.507-1(a) (Electric equipment other 
than power-connection points; outby the last open crosscut; return air; 
permissibility requirements).
    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment in 
return airways, including, but not limited to, portable battery-
operated mine transits, total station surveying equipment, distance 
meters, and data loggers. The petitioner states that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance 
meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used in 
return airways will be examined by surveying personnel prior to use to 
ensure the equipment is being maintained in a safe operating condition. 
These examinations will include the following steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.
    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment in return airways.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn out of the return airways.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air out of the return.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards associated with the use of 
nonpermissible surveying equipment in areas where methane could be 
present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.
    Docket Number: M-2012-114-C.
    Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite 
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
    Mine: Bronzite III Mine, MSHA I.D. No. 46-05978, located in Mingo 
County, West Virginia.
    Regulation Affected: 30 CFR 75.1002(a) (Installation of electric 
equipment and conductors; permissibility).
    Modification Request: The petitioner requests a modification of the 
existing standard to permit an alternative method of compliance to 
permit the use of battery-powered nonpermissible surveying equipment 
within 150 feet of pillar workings, including, but not limited to, 
portable battery-operated mine transits, total station surveying 
equipment, distance meters, and data loggers. The petitioner states 
that:
    (1) To comply with requirements for mine ventilation maps and mine 
maps in 30 CFR 75.372 and 75.1200, use of the most practical and 
accurate surveying equipment is necessary. To ensure the safety of the 
miners in active mines and to protect miners in future mines that may 
mine in close proximity to these same active mines, it is necessary to 
determine the exact location and extent of the mine workings.
    (2) Application of the existing standard would result in a 
diminution of safety to the miners. Underground mining by its nature 
and size, and the complexity of mine plans, requires that accurate and 
precise measurements be completed in a prompt and efficient manner. The 
petitioner proposes the following as an alternative to the existing 
standard:
    (a) Nonpermissible electronic surveying equipment will be used when 
equivalent permissible electronic surveying equipment is not available. 
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance 
meters, and data loggers.
    (b) All nonpermissible electronic surveying equipment to be used 
within 150 feet of pillar workings will be examined by surveying 
personnel prior to use to ensure the equipment is being maintained in a 
safe operating condition. These examinations will include the following 
steps:
    (i) Checking the instrument for any physical damage and the 
integrity of the case.
    (ii) Removing the battery and inspecting for corrosion.

[[Page 38336]]

    (iii) Inspecting the contact points to ensure a secure connection 
to the battery.
    (iv) Reinserting the battery and powering up and shutting down to 
ensure proper connections.
    (v) Checking the battery compartment cover to ensure that it is 
securely fastened.
    (c) The results of such examinations will be recorded and retained 
for one year and made available to MSHA on request.
    (d) A qualified person as defined in 30 CFR 75.151 will 
continuously monitor for methane immediately before and during the use 
of nonpermissible surveying equipment within 150 feet of pillar 
workings.
    (e) Nonpermissible surveying equipment will not be used if methane 
is detected in concentrations at or above one percent for the area 
being surveyed. When methane is detected at such levels while the 
nonpermissible surveying equipment is being used, the equipment will be 
deenergized immediately and the nonpermissible electronic equipment 
withdrawn further than 150 feet from pillar workings.
    (f) All hand-held methane detectors will be MSHA-approved and 
maintained in permissible and proper operating condition as defined in 
30 CFR 75.320.
    (g) Batteries in the surveying equipment must be changed out or 
charged in fresh air more than 150 feet from pillar workings.
    (h) Qualified personnel who use surveying equipment will be 
properly trained to recognize the hazards and limitations associated 
with the use of nonpermissible surveying equipment in areas where 
methane could be present.
    (i) The nonpermissible surveying equipment will not be put into 
service until MSHA has initially inspected the equipment and determined 
that it is in compliance with all the terms and conditions in this 
petition.
    Within 60 days after the Proposed Decision and Order becomes final, 
the petitioner will submit proposed revisions for its approved 30 CFR 
part 48 training plan to the District Manager. The revisions will 
specify initial and refresher training regarding the terms and 
conditions in the Proposed Decision and Order.
    The petitioner asserts that the proposed alternative method will at 
all times guarantee no less than the same measure of protection as that 
afforded by the existing standard.

    Dated: June 22, 2012.
George F. Triebsch,
Director, Office of Standards, Regulations and Variances.
[FR Doc. 2012-15672 Filed 6-26-12; 8:45 am]
BILLING CODE 4510-43-P