[Federal Register Volume 75, Number 201 (Tuesday, October 19, 2010)]
[Notices]
[Pages 64246-64247]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2010-26268]


-----------------------------------------------------------------------

DEPARTMENT OF COMMERCE

International Trade Administration

[A-351-828]


Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From 
Brazil: Correction to Notice of Antidumping Duty Order

AGENCY: Import Administration, International Trade Administration, 
Department of Commerce.

DATES: Effective Date: October 19, 2010.

FOR FURTHER INFORMATION CONTACT: David Cordell or Ericka Ukrow, AD/CVD 
Operations, Office 7, Import Administration, International Trade 
Administration, U.S. Department of Commerce, 14th Street and 
Constitution Avenue, NW., Washington, DC 20230; telephone: (202) 482-
0408 or (202) 482-0405, respectively.

Correction

    On March 12, 2002, the Department published a notice of antidumping 
duty order for certain hot-rolled flat-rolled carbon-quality steel 
products from Brazil. See Antidumping Duty Order: Certain Hot-Rolled 
Flat-Rolled Carbon-Quality Steel Products From Brazil, 67 FR 11093 
(March 12, 2002) (``Order''). The Order states incorrectly that 
``certain hot-rolled steel coil which meets the following chemical, 
physical and mechanical specifications is outside and/or specifically 
excluded from the scope of the order.''
    Hot-rolled steel coil which meets the following chemical, physical 
and mechanical specifications:

----------------------------------------------------------------------------------------------------------------
      C              Mn             P             S            Si            Cr            Cu            Ni
----------------------------------------------------------------------------------------------------------------
0.10-0.14%     0.90% Max.     0.025% Max.   0.005% Max.   0.30-0.50%    0.30-0.50%    0.20-0.40%    0.20% Max.
----------------------------------------------------------------------------------------------------------------
Width = 44.80 inches maximum; Thickness = 0.063-0.198 inches; Yield Strength = 50,000 ksi minimum; Tensile
  Strength = 70,000-88,000 psi.

    Hot-rolled steel coil which meets the following chemical, physical 
and mechanical specifications:

[[Page 64247]]



----------------------------------------------------------------------------------------------------------------
     C            Mn           P            S            Si           Cr          Cu          Ni          Mo
----------------------------------------------------------------------------------------------------------------
0.10-0.16%   0.70--0.90%  0.025% Max.  0.006% Max.  0.30-0.50%   0.30-0.50%   0.25% Max.  0.20% Max.  0.21% Max.
----------------------------------------------------------------------------------------------------------------
Width = 44.80 inches maximum; Thickness = 0.350 inches maximum; Yield Strength = 80,000 ksi minimum; Tensile
  Strength = 105,000 psi Aim.


--------------------------------------------------------------------------------------------------------------------------------------------------------
      C            Mn             P             S            Si            Cr            Cu            Ni            Nb            Ca            Al
--------------------------------------------------------------------------------------------------------------------------------------------------------
0.15% Max.    1.40% Max.    0.025% Max.   0.010% Max.   0.50% Max.    1.00% Max.    0.50% Max.    0.20% Max.    0.005% Min.   Treated       0.01--0.70%
                                                                                                                                             Max.
--------------------------------------------------------------------------------------------------------------------------------------------------------
Width = 39.37 inches; Thickness = 0.181 inches maximum; Yield Strength = 70,000 psi minimum for thicknesses; 0.148 inches and 65,000 psi minimum for
  thicknesses > 0.148 inches; Tensile Strength = 80,000 psi minimum. See Order at 11093, 11094.

    In addition, the terminology in the ``scope of the order'' section 
incorrectly uses the word ``agreement'' seven times instead of 
referring to the ``order'' itself. The first four instances incorrectly 
uses the phrase ``scope of this agreement.'' The final three 
incorrectly state (1) ``subject to this agreement'' (2) ``covered by 
this agreement'' and (3) ``under this agreement.''
    The Order is hereby corrected to read that certain hot-rolled steel 
coil which meets the following chemical, physical and mechanical 
specifications is excluded from the scope of the order.\1\
---------------------------------------------------------------------------

    \1\ See also the Antidumping Duty Order; Certain Hot-Rolled 
Flat-Rolled Carbon-Quality Steel Products From Japan, 64 FR 34778 
(June 29, 1999).
---------------------------------------------------------------------------

    Hot-rolled steel coil which meets the following chemical, physical 
and mechanical specifications:

----------------------------------------------------------------------------------------------------------------
      C              Mn             P             S            Si            Cr            Cu            Ni
----------------------------------------------------------------------------------------------------------------
0.10-0.14%     0.90% Max.     0.025% Max.   0.005% Max.   0.30-0.50%    0.50-0.70%    0.20-0.40%    0.20% Max.
----------------------------------------------------------------------------------------------------------------
Width = 44.80 inches maximum; Thickness = 0.063-0.198 inches; Yield Strength = 50,000 ksi minimum; Tensile
  Strength = 70,000-88,000 psi.

    Hot-rolled steel coil which meets the following chemical, physical 
and mechanical specifications:

----------------------------------------------------------------------------------------------------------------
     C            Mn           P            S            Si           Cr          Cu          Ni          Mo
----------------------------------------------------------------------------------------------------------------
0.10-0.16%   0.70--0.90%  0.025% Max.  0.006% Max.  0.30-0.50%   0.50-0.70%   0.25% Max.  0.20% Max.  0.21% Max.
----------------------------------------------------------------------------------------------------------------
Width = 44.80 inches maximum; Thickness = 0.350 inches maximum; Yield Strength = 80,000 ksi minimum; Tensile
  Strength = 105,000 psi Aim.

    Hot-rolled steel coil which meets the following chemical, physical 
and mechanical specifications:

--------------------------------------------------------------------------------------------------------------------------------------------------------
      C            Mn             P             S            Si            Cr            Cu            Ni            Nb            Ca            Al
--------------------------------------------------------------------------------------------------------------------------------------------------------
0.15% Max.    1.40% Max.    0.025% Max.   0.010% Max.   0.50% Max.    1.00% Max.    0.50% Max.    0.20% Max.    0.005% Min.   Treated       0.01-0.07%
                                                                                                                                             Max.
--------------------------------------------------------------------------------------------------------------------------------------------------------
Width = 39.37 inches; Thickness = 0.181 inches maximum; Yield Strength = 70,000 psi minimum for thicknesses; 0.148 inches and 65,000 psi minimum for
  thicknesses > 0.148 inches; Tensile Strength = 80,000 psi minimum. See Order at 11093, 11094.

    The Order is hereby corrected to refer to itself as an ``order'' in 
all cases where ``agreement'' was used in the ``scope of the order'' 
section of the Order.
    This notice is published in accordance with section 777(i) of the 
Tariff Act of 1930, as amended.

     Dated: October 12, 2010
Ronald K. Lorentzen,
Deputy Assistant Secretary for Import Administration.
[FR Doc. 2010-26268 Filed 10-18-10; 8:45 am]
BILLING CODE 3510-DS-P