[Federal Register Volume 75, Number 139 (Wednesday, July 21, 2010)]
[Rules and Regulations]
[Pages 42311-42314]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2010-17722]


=======================================================================
-----------------------------------------------------------------------

CONSUMER PRODUCT SAFETY COMMISSION

16 CFR Part 1611

[CPSC Docket No. CPSC-2010-0079]


Third Party Testing for Certain Children's Products; Vinyl 
Plastic Film: Requirements for Accreditation of Third Party Conformity 
Assessment Bodies

AGENCY: Consumer Product Safety Commission.

ACTION: Notice of requirements.

-----------------------------------------------------------------------

SUMMARY: The Consumer Product Safety Commission (CPSC or Commission) is 
issuing a notice of requirements that provides the criteria and process 
for Commission acceptance of accreditation of third party conformity 
assessment bodies for testing pursuant to the CPSC regulations under 
the Flammable Fabrics Act relating to vinyl plastic film. The 
Commission is issuing this notice of requirements pursuant to the 
Consumer Product Safety Act (CPSA).

DATES: Effective Date: The requirements for accreditation of third 
party conformity assessment bodies to assess conformity with 16 CFR 
part 1611 are effective upon publication of this document in the 
Federal Register.\1\
---------------------------------------------------------------------------

    \1\ The Commission voted 3-2 to publish this notice of 
requirements. Chairman Inez M. Tenenbaum, Commissioner Nancy A. 
Nord, and Commissioner Anne Meagher Northup each issued a statement, 
and the statements can be found at http://www.cpsc.gov/pr/statements.html.
---------------------------------------------------------------------------

    Comments in response to this notice of requirements should be 
submitted by August 20, 2010. Comments should be captioned ``Third 
Party Testing for Certain Children's Products; Vinyl Plastic Film: 
Requirements for Accreditation of Third Party Conformity Assessment 
Bodies.''

ADDRESSES: You may submit comments, identified by Docket No. CPSC-2010-
0079, by any of the following methods:
     Electronic Submissions: Submit electronic comments in the 
following way:
     Federal eRulemaking Portal: http://www.regulations.gov. 
Follow the instructions for submitting comments.

[[Page 42312]]

To ensure timely processing of comments, the Commission is no longer 
accepting comments submitted by electronic mail (e-mail) except through 
http://www.regulations.gov.
     Written Submissions: Submit written submissions in the 
following way:
    Mail/Hand delivery/Courier (for paper, disk, or CD-ROM submissions) 
preferably in five copies, to: Office of the Secretary, U.S. Consumer 
Product Safety Commission, Room 820, 4330 East-West Highway, Bethesda, 
Maryland 20814; telephone (301) 504-7923.
    Instructions: All submissions received must include the agency name 
and docket number for this notice. All comments received may be posted 
without change to http://www.regulations.gov, including any personal 
information provided. Do not submit confidential business information, 
trade secret information, or other sensitive or protected information 
(such as a Social Security Number) electronically; if furnished at all, 
such information should be submitted in writing.
    Docket: For access to the docket to read background documents or 
comments received, go to http://www.regulations.gov.

FOR FURTHER INFORMATION CONTACT: Robert ``Jay'' Howell, Assistant 
Executive Director for Hazard Identification and Reduction, U.S. 
Consumer Product Safety Commission, 4330 East-West Highway, Bethesda, 
Maryland 20814; e-mail [email protected].

SUPPLEMENTARY INFORMATION:

I. Introduction

    Section 14(a)(3)(B)(vi) of the CPSA, as added by section 102(a)(2) 
of the Consumer Product Safety Improvement Act of 2008 (CPSIA), Public 
Law 110-314, directs the CPSC to publish a notice of requirements for 
accreditation of third party conformity assessment bodies to assess 
children's products for conformity with ``other children's product 
safety rules.'' Section 14(f)(1) of the CPSA defines ``children's 
product safety rule'' as ``a consumer product safety rule under [the 
CPSA] or similar rule, regulation, standard, or ban under any other Act 
enforced by the Commission, including a rule declaring a consumer 
product to be a banned hazardous product or substance.'' Under section 
14(a)(3)(A) of the CPSA, each manufacturer (including the importer) or 
private labeler of products subject to those regulations must have 
products that are manufactured more than 90 days after the Federal 
Register publication date of a notice of the requirements for 
accreditation, tested by a third party conformity assessment body 
accredited to do so, and must issue a certificate of compliance with 
the applicable regulations based on that testing. Section 14(a)(2) of 
the CPSA, as added by section 102(a)(2) of the CPSIA, requires that 
certification be based on testing of sufficient samples of the product, 
or samples that are identical in all material respects to the product. 
The Commission also emphasizes that, irrespective of certification, the 
product in question must comply with applicable CPSC requirements (see, 
e.g., section 14(h) of the CPSA, as added by section 102(b) of the 
CPSIA).
    The Commission also is recognizing limited circumstances in which 
it will accept certifications based on product testing conducted before 
the third party conformity assessment body is accepted as accredited by 
the CPSC. The details regarding those limited circumstances can be 
found in part IV of this document below.
    This notice provides the criteria and process for Commission 
acceptance of accreditation of third party conformity assessment bodies 
for testing pursuant to 16 CFR part 1611, Standard for the Flammability 
of Vinyl Plastic Film, which sets a minimum standard for flammability 
of vinyl plastic film which are subject to the requirements of the 
Flammable Fabrics Act (15 U.S.C. 1191 et seq.) (FFA).
    Section 3(a)(2) of the CPSA defines a children's product as ``a 
consumer product designed or intended primarily for children 12 years 
of age or younger.'' Although vinyl plastic film used in wearing 
apparel or fabric is often for general use (that is, it is produced for 
general consumption rather than being produced specifically for use by 
children), some vinyl plastic film wearing apparel or fabric is 
``designed or intended primarily for children 12 years of age or 
younger.'' (For convenience, we will refer to vinyl plastic film 
products designed or intended primarily for use in wearing apparel or 
fabric for children 12 years of age or younger as ``youth vinyl plastic 
film products.'') Youth vinyl plastic film products are subject to the 
third party testing and certification requirements in section 14(a)(2) 
of the CPSA. Accordingly, this notice of requirements addresses the 
accreditation of conformity assessment bodies to test youth vinyl 
plastic film for conformity with 16 CFR part 1611.
    Although section 14(a)(3)(B)(vi) of the CPSA directs the CPSC to 
publish a notice of requirements for accreditation of third party 
conformity assessment bodies to assess conformity with ``all other 
children's product safety rules,'' this notice of requirements is 
limited to the regulations identified immediately above.
    The CPSC also recognizes that section 14(a)(3)(B)(vi) of the CPSA 
is captioned as ``All Other Children's Product Safety Rules,'' but the 
body of the statutory requirement refers only to ``other children's 
product safety rules.'' Nevertheless, section 14(a)(3)(B)(vi) of the 
CPSA could be construed as requiring a notice of requirements for 
``all'' other children's product safety rules, rather than a notice of 
requirements for ``some'' or ``certain'' children's product safety 
rules. However, whether a particular rule represents a ``children's 
product safety rule'' may be subject to interpretation, and the 
Commission staff is continuing to evaluate which rules, regulations, 
standards, or bans are ``children's product safety rules.'' The CPSC 
intends to issue additional notices of requirements for other rules 
which the Commission determines to be ``children's product safety 
rules.''
    This notice of requirements applies to all third party conformity 
assessment bodies as described in section 14(f)(2) of the CPSA. 
Generally speaking, such third party conformity assessment bodies are: 
(1) Third party conformity assessment bodies that are not owned, 
managed, or controlled by a manufacturer or private labeler of a 
children's product to be tested by the third party conformity 
assessment body for certification purposes; (2) ``firewalled'' 
conformity assessment bodies (those that are owned, managed, or 
controlled by a manufacturer or private labeler of a children's product 
to be tested by the third party conformity assessment body for 
certification purposes and that seek accreditation under the additional 
statutory criteria for ``firewalled'' conformity assessment bodies); 
and (3) third party conformity assessment bodies owned or controlled, 
in whole or in part, by a government.
    The Commission requires baseline accreditation of each category of 
third party conformity assessment body to the International 
Organization for Standardization (ISO)/International Electrotechnical 
Commission (IEC) Standard 17025:2005, ``General Requirements for the 
Competence of Testing and Calibration Laboratories.'' The accreditation 
must be by an accreditation body that is a signatory to the 
International Laboratory Accreditation Cooperation-Mutual Recognition 
Arrangement (ILAC-MRA), and the scope of the accreditation must include 
testing in accordance with the regulations identified earlier in part I 
of this document for which the third party

[[Page 42313]]

conformity assessment body seeks to be accredited.
    (A description of the history and content of the ILAC-MRA approach 
and of the requirements of the ISO/IEC 17025:2005 laboratory 
accreditation standard is provided in the CPSC staff briefing 
memorandum ``Third Party Conformity Assessment Body Accreditation 
Requirements for Testing Compliance with 16 CFR Part 1501 (Small Parts 
Regulations),'' dated November 2008 and available on the CPSC's Web 
site at http://www.cpsc.gov/library/foia/foia09/brief/smallparts.pdf.)
    The Commission has established an electronic accreditation 
registration and listing system that can be accessed via its Web site 
at http://www.cpsc.gov/ABOUT/Cpsia/labaccred.html.
    The Commission stayed the enforcement of certain provisions of 
section 14(a) of the CPSA in a notice published in the Federal Register 
on February 9, 2009 (74 FR 6396); the stay applied to testing and 
certification of various products, including vinyl plastic film. On 
December 28, 2009, the Commission published a notice in the Federal 
Register (74 FR 68588) revising the terms of the stay. One section of 
the December 28, 2009, notice addressed ``Consumer Products or 
Children's Products Where the Commission Is Continuing the Stay of 
Enforcement Until Further Notice,'' due to factors such as pending 
rulemaking proceedings affecting the product or the absence of a notice 
of requirements. The vinyl plastic film testing and certification 
requirements were included in that section of the December 28, 2009, 
notice. As the factor preventing the stay from being lifted in the 
December 28, 2009, notice with regard to testing and certifications of 
vinyl plastic film was the absence of a notice of requirements, 
publication of this notice has the effect of lifting the stay with 
regard to 16 CFR part 1611.
    The Commission noted in the December 28, 2009, notice that the stay 
of enforcement did not extend to guaranties under the FFA. The 
manufacturer or supplier of vinyl plastic film may issue a guaranty, 
based on reasonable and representative testing, that the vinyl plastic 
film complies with FFA standards. The holder of a valid guaranty is not 
subject to criminal prosecution under section 7 of the FFA (penalties) 
for a violation of section 3 of the FFA (prohibited transactions).
    The reasonable and representative tests sufficient for the issuance 
of an FFA guaranty are generally performed by the manufacturer; those 
tests are sufficient for the issuance of a general conformity 
certification for nonchildren's products under section 14(a)(1) of the 
CPSA. However, because section 14(a)(2) of the CPSA requires children's 
products subject to a children's product safety rule to be tested by an 
accredited third party conformity assessment body, reasonable and 
representative tests sufficient for the issuance of an FFA guaranty 
which are performed by a manufacturer are not sufficient for the 
issuance of a certification of compliance with 16 CFR part 1611 for 
youth vinyl plastic film products (unless the manufacturer's facility 
is a CPSC-accredited firewalled conformity assessment body).
    This notice of requirements is effective on July 21, 2010. Further, 
as the publication of this notice of requirements effectively lifts the 
stay of enforcement with regard to testing and certifications related 
to 16 CFR part 1611, each manufacturer of a children's product subject 
to 16 CFR part 1611 must have any such product manufactured after 
October 19, 2010 tested by a third party conformity assessment body 
accredited to do so and must issue a certificate of compliance with 16 
CFR part 1611 based on that testing. (Under the CPSA, the term 
``manufacturer'' includes anyone who manufactures or imports a 
product.)
    This notice of requirements is exempt from the notice and comment 
rulemaking requirements of the Administrative Procedure Act, 5 U.S.C. 
553 (see section 14(a)(3)(G) of the CPSA, as added by section 102(a)(2) 
of the CPSIA (15 U.S.C. 2063(a)(3)(G)).

II. Accreditation Requirements

A. Baseline Third Party Conformity Assessment Body Accreditation 
Requirements

    For a third party conformity assessment body to be accredited to 
test children's products for conformity with the test methods in the 
regulations identified earlier in part I of this document, it must be 
accredited by an ILAC-MRA signatory accrediting body, and the 
accreditation must be registered with, and accepted by, the Commission. 
A listing of ILAC-MRA signatory accrediting bodies is available on the 
Internet at http://ilac.org/membersbycategory.html. The accreditation 
must be to ISO Standard ISO/IEC 17025:2005, ``General Requirements for 
the Competence of Testing and Calibration Laboratories,'' and the scope 
of the accreditation must expressly include testing to the regulations 
in 16 CFR part 1611, Standard for the Flammability of Vinyl Plastic 
Film. A true copy, in English, of the accreditation and scope documents 
demonstrating compliance with the requirements of this notice must be 
registered with the Commission electronically. The additional 
requirements for accreditation of firewalled and governmental 
conformity assessment bodies are described in parts II.B and II.C of 
this document below.
    The Commission will maintain on its Web site an up-to-date listing 
of third party conformity assessment bodies whose accreditations it has 
accepted and the scope of each accreditation. Subject to the limited 
provisions for acceptance of ``retrospective'' testing noted in part IV 
below, once the Commission adds a third party conformity assessment 
body to that list, the third party conformity assessment body may 
commence testing of children's products to support the manufacturer's 
certification that the product complies with the regulations identified 
earlier in part I of this document.

B. Additional Accreditation Requirements for Firewalled Conformity 
Assessment Bodies

    In addition to the baseline accreditation requirements in part II.A 
of this document above, firewalled conformity assessment bodies seeking 
accredited status must submit to the Commission copies, in English, of 
their training documents showing how employees are trained to notify 
the Commission immediately and confidentially of any attempt by the 
manufacturer, private labeler, or other interested party to hide or 
exert undue influence over the third party conformity assessment body's 
test results. This additional requirement applies to any third party 
conformity assessment body in which a manufacturer or private labeler 
of a children's product to be tested by the third party conformity 
assessment body owns an interest of ten percent or more. While the 
Commission is not addressing common parentage of a third party 
conformity assessment body and a children's product manufacturer at 
this time, it will be vigilant to see if this issue needs to be 
addressed in the future.
    As required by section 14(f)(2)(D) of the CPSA, the Commission must 
formally accept, by order, the accreditation application of a third 
party conformity assessment body before the third party conformity 
assessment body can become an accredited firewalled conformity 
assessment body.

[[Page 42314]]

C. Additional Accreditation Requirements for Governmental Conformity 
Assessment Bodies

    In addition to the baseline accreditation requirements of part II.A 
of this document above, the CPSIA permits accreditation of a third 
party conformity assessment body owned or controlled, in whole or in 
part, by a government if:
     To the extent practicable, manufacturers or private 
labelers located in any nation are permitted to choose conformity 
assessment bodies that are not owned or controlled by the government of 
that nation;
     The third party conformity assessment body's testing 
results are not subject to undue influence by any other person, 
including another governmental entity;
     The third party conformity assessment body is not accorded 
more favorable treatment than other third party conformity assessment 
bodies in the same nation who have been accredited;
     The third party conformity assessment body's testing 
results are accorded no greater weight by other governmental 
authorities than those of other accredited third party conformity 
assessment bodies; and
     The third party conformity assessment body does not 
exercise undue influence over other governmental authorities on matters 
affecting its operations or on decisions by other governmental 
authorities controlling distribution of products based on outcomes of 
the third party conformity assessment body's conformity assessments.
    The Commission will accept the accreditation of a governmental 
third party conformity assessment body if it meets the baseline 
accreditation requirements of part II.A of this document above and 
meets the additional conditions stated here. To obtain this assurance, 
CPSC staff will engage the governmental entities relevant to the 
accreditation request.

III. How does a third party conformity assessment body apply for 
acceptance of its accreditation?

    The Commission has established an electronic accreditation 
acceptance and registration system accessed via the Commission's 
Internet site at http://www.cpsc.gov/about/cpsia/labaccred.html. The 
applicant provides, in English, basic identifying information 
concerning its location, the type of accreditation it is seeking, and 
electronic copies of its ILAC-MRA accreditation certificate and scope 
statement, and firewalled third party conformity assessment body 
training document(s), if relevant.
    Commission staff will review the submission for accuracy and 
completeness. In the case of baseline third party conformity assessment 
bodies and government-owned or government-operated conformity 
assessment bodies, when that review and any necessary discussions with 
the applicant are satisfactorily completed, the third party conformity 
assessment body in question is added to the CPSC's list of accredited 
third party conformity assessment bodies at http://www.cpsc.gov/about/
cpsia/labaccred.html. In the case of a firewalled conformity assessment 
body seeking accredited status, when the staff's review is complete, 
the staff transmits its recommendation on accreditation to the 
Commission for consideration. (A third party conformity assessment body 
that may ultimately seek acceptance as a firewalled third party 
conformity assessment body also can initially request acceptance as a 
third party conformity assessment body accredited for testing of 
children's products other than those of its owners.) If the Commission 
accepts a staff recommendation to accredit a firewalled conformity 
assessment body, the firewalled conformity assessment body will then be 
added to the CPSC's list of accredited third party conformity 
assessment bodies. In each case, the Commission will notify the third 
party conformity assessment body electronically of acceptance of its 
accreditation. All information to support an accreditation acceptance 
request must be provided in the English language.
    Subject to the limited provisions for acceptance of 
``retrospective'' testing noted in part IV of this document below, once 
the Commission adds a third party conformity assessment body to the 
list, the third party conformity assessment body may then begin testing 
of children's products to support certification of compliance with the 
regulations identified earlier in part I of this document for which it 
has been accredited.

IV. Limited Acceptance of Children's Product Certifications Based on 
Third Party Conformity Assessment Body Testing Prior to the 
Commission's Acceptance of Accreditation

    The Commission will accept a certificate of compliance with the 
standard for vinyl plastic film included in 16 CFR part 1611, Standard 
for the Flammability of Vinyl Plastic Film, based on testing performed 
by an accredited third party conformity assessment body (including a 
government-owned or -controlled conformity assessment body, and a 
firewalled conformity assessment body) prior to the Commission's 
acceptance of its accreditation if:
     At the time of product testing, the product was tested by 
a third party conformity assessment body that was ISO/IEC 17025 
accredited by an ILAC-MRA member at the time of the test. For 
firewalled conformity assessment bodies, the firewalled conformity 
assessment body must be one that the Commission accredited by order at 
or before the time the product was tested, even though the order will 
not have included the test methods in the regulations specified in this 
notice. If the third party conformity assessment body has not been 
accredited by a Commission order as a firewalled conformity assessment 
body, the Commission will not accept a certificate of compliance based 
on testing performed by the third party conformity assessment body 
before it is accredited, by Commission order, as a firewalled 
conformity assessment body;
     The third party conformity assessment body's application 
for testing using the test methods in the regulations identified in 
this notice is accepted by the CPSC on or before September 20, 2010;
     The product was tested on or after July 21, 2010 with 
respect to the regulations identified in this notice;
     The accreditation scope in effect for the third party 
conformity assessment body at the time of testing expressly included 
testing to the regulations identified earlier in part I of this 
document;
     The test results show compliance with the applicable 
current standards and/or regulations; and
     The third party conformity assessment body's 
accreditation, including inclusion in its scope the standards described 
in part I of this notice, remains in effect through the effective date 
for mandatory third party testing and manufacturer certification for 
conformity with 16 CFR part 1611.

    Dated: July 15, 2010.
Todd A. Stevenson,
Secretary, Consumer Product Safety Commission.
[FR Doc. 2010-17722 Filed 7-20-10; 8:45 am]
BILLING CODE 6355-01-P