[Federal Register Volume 75, Number 81 (Wednesday, April 28, 2010)]
[Rules and Regulations]
[Pages 22219-22227]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2010-9612]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF THE INTERIOR

Minerals Management Service

30 CFR Part 250

[Docket ID: MMS-2008-OMM-0044]
RIN 1010-AD54


Update of Revised and Reaffirmed Documents Incorporated by 
Reference

AGENCY: Minerals Management Service (MMS), Interior.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: This final rule incorporates 21 revised editions and 17 
reaffirmed editions of documents previously incorporated by reference 
in regulations governing oil and gas and sulphur operations in the 
Outer Continental Shelf. Additionally, this final rule will rectify an 
incorrect reference to American Petroleum Institute (API) 510. The 
revised and reaffirmed editions of these documents will ensure that 
lessees use the best and safest technologies available while operating 
in the Outer Continental Shelf.

DATES: Effective Date: This final rule is effective May 28, 2010. The 
incorporation by reference of publications listed in the regulation is 
approved by the Director of the Federal Register as of May 28, 2010.

FOR FURTHER INFORMATION CONTACT: Wilbon Rhome at (703) 787-1587.

SUPPLEMENTARY INFORMATION: The MMS uses standards, specifications, and 
recommended practices developed by standard-setting organizations and 
the oil and gas industry as a means of establishing requirements for 
activities on the Outer Continental Shelf (OCS). This practice, known 
as incorporation by reference, allows us to incorporate the provisions 
of technical standards into the regulations. The legal effect of 
incorporation by reference is that the material is treated as if the 
entire document was published in the Federal Register. This material, 
like any other properly issued regulation, then has the force and 
effect of law. We hold operators/lessees accountable for complying with 
the documents incorporated by reference in our regulations. We 
currently incorporate by reference 97 consensus standards into the 
offshore operating regulations.
    The regulations at 1 CFR part 51 govern how we and other Federal 
agencies incorporate various documents by reference. Agencies may only 
incorporate a document by reference by publishing the document title 
and affirmation/reaffirmation date in the Federal Register. Agencies 
must also gain approval from the Director of the Federal Register for 
each publication incorporated by reference. Incorporation by reference 
of a document or publication is limited to the specific edition, 
supplement, or addendum cited in the regulations. The MMS is 
reformatting the appearance of this section in the regulations 
concerning documents incorporated by reference. This section, 30 CFR 
250.198, will now be formatted to be consistent with the guidance 
provided by the Office of the Federal Register. This new format will 
continue to clearly identify the documents incorporated by reference in 
the 30 CFR part 250 regulations.
    Under 5 U.S.C. 553 and the regulations found at 30 CFR 250.198(a), 
MMS may update documents without an opportunity for public comment when 
we determine that the revisions to

[[Page 22220]]

a document result in safety improvements, or represent new industry 
standard technology and do not impose undue cost or burden on the 
affected parties. Accordingly, this final rule incorporates the revised 
editions of 21 documents and 17 reaffirmed documents previously 
incorporated by reference in regulations governing oil and gas and 
sulphur operations in the OCS. These new and reaffirmed documents will 
ensure that lessees use the best and safest technologies available 
while operating in the OCS.
    In this final rule, ``reaffirmed'' references an action taken by 
the American Petroleum Institute (API) standards committee, normally 
within a 5-year timeframe, and confirms that the information contained 
within the standard is still applicable and requires no change at this 
time. Also, the edition number and date of the standard does not change 
as a result of reaffirmation by the standards committee. Additionally, 
we are correcting a reference to API 510, Pressure Vessel Inspections 
Code: In-Service Inspection, Rating, Repair, and Alteration, in our 
regulations at Sec.  250.803(b)(1) and Sec.  250.1629(b)(1) to make a 
section reference change (from 6.5 and 8.5 to 5.8 and 9.5).
    The MMS has reviewed these documents and determined the revised 
editions must be incorporated into the regulations to ensure the use of 
the best and safest technologies. Our review shows that changes between 
the old and new editions result in safety improvements, or represent 
new industry standard technology and will not impose undue cost or 
burden on the offshore oil and gas industry. Furthermore, old editions 
may not be readily available to the affected parties because they are 
out of publication, so we are amending our regulations to incorporate 
the updated editions.

Revised Editions

    The revised editions of the documents incorporated by reference in 
this final rule are:

------------------------------------------------------------------------
                           Title of Documents
-------------------------------------------------------------------------
API MPMS, Chapter 10--Sediment and Water, Section 1--Standard Test
 Method for Sediment in Crude Oils and Fuel Oils by the Extraction
 Method, Third Edition, November 2007; Product No. H10013.
API MPMS, Chapter 10--Sediment and Water, Section 2--Standard Test;
 Method for Water in Crude Oil by Distillation, Second Edition, November
 2007; Product No. H10022.
API MPMS, Chapter 10--Sediment and Water, Section 3--Standard Test
 Method for Water and Sediment in Crude Oil by the Centrifuge Method
 (Laboratory Procedure), Third Edition, May 2008; Product No. H10033.
API MPMS, Chapter 14.5/GPA Standard 2172-09; Calculation of Gross
 Heating Value, Relative Density, Compressibility and Theoretical
 Hydrocarbon Liquid Content for Natural Gas Mixtures for Custody
 Transfer; Third Edition, January 2009; Adopted as Tentative Standard,
 1972; Revised and Adopted as Standard, 1976; Revised 1984, 1986, 1996,
 2009; Product No. H140503.
API RP 2A-WSD, Recommended Practice for Planning, Designing and
 Constructing Fixed Offshore Platforms--Working Stress Design, Twenty-
 first Edition, December 2000; Errata and Supplement 1, December 2002;
 Errata and Supplement 2, September 2005, Errata and Supplement 3,
 October 2007; Product No. G2AWSD.
API RP 2D, Operation and Maintenance of Offshore Cranes, Sixth Edition,
 May 2007; Product No. G02D06.
API RP 2I, In-service Inspection of Mooring Hardware for Floating
 Structures, Third Edition, April 2008; Product No. G02I03.
API RP 2SK, Design and Analysis of Stationkeeping Systems for Floating
 Structures, Third Edition, October 2005, Addendum, May 2008; Product
 No. G2SK03.
API RP 2SM Recommended Practice for Design, Manufacture, Installation,
 and Maintenance of Synthetic Fiber Ropes for Offshore Mooring, First
 Edition, March 2001, Addendum, May 2007; Product No. G02SM1.
API RP 14F, Design, Installation, and Maintenance of Electrical Systems
 for Fixed and Floating Offshore Petroleum Facilities for Unclassified
 and Class I, Division 1 and Division 2 Locations, Fifth Edition, July
 2008; Product No. G14F05.
API RP 14G, Recommended Practice for Fire Prevention and Control on
 Fixed Open-Type Offshore Production Platforms, Fourth Edition, April
 2007; Product No. G14G04.
API RP 14H, Recommended Practice for Installation, Maintenance and
 Repair of Surface Safety Valves and Underwater Safety Valves Offshore,
 Fifth Edition, August 2007; Product No. G14H05.
ANSI/API Spec. Q1, Specification for Quality Programs for the Petroleum,
 Petrochemical and Natural Gas Industry, ISO TS 29001:2007 (Identical),
 Petroleum, petrochemical and natural gas industries--Sector specific
 requirements--Requirements for product and service supply
 organizations, Eighth Edition, December 2007, Effective Date: June 15,
 2008; Product No. GXQ108.
ANSI/API Spec. 6A, Specification for Wellhead and Christmas Tree
 Equipment, Nineteenth Edition, July 2004; Effective Date: February 1,
 2005; Contains API Monogram Annex as Part of U.S. National Adoption;
 ISO 10423:2003 (Modified), Petroleum and natural gas industries--
 Drilling and production equipment--Wellhead and Christmas tree
 equipment; Errata 1, September 2004, Errata 2, April 2005, Errata 3,
 June 2006, Errata 4, August 2007, Errata 5, May 2009; Addendum 1,
 February 2008; Addendum 2, 3, and 4, December 2008; Product No.
 GX06A19.
ANSI/API Spec. 6D, Specification for Pipeline Valves, Twenty-third
 Edition, April 2008; Effective Date: October 1, 2008, Errata 1, June
 2008; Errata 2, November 2008; Errata 3, February 2009; Addendum 1,
 October 2009; Contains API Monogram Annex as Part of U.S. National
 Adoption; ISO 14313:2007 (Identical), Petroleum and natural gas
 industries--Pipeline transportation systems--Pipeline valves; Product
 No. GX6D23.
ANSI/API Spec. 17J, Specification for Unbonded Flexible Pipe, Third
 Edition, July 2008; Effective Date: January 1, 2009, Contains API
 Monogram Annex as Part of U.S. National Adoption; ISO 13628-2:2006
 (Identical), Petroleum and natural gas industries--Design and operation
 of subsea production systems--Part 2: Unbonded flexible pipe systems
 for subsea and marine application; Product No. GX17J03.
ASTM Standard C 33-07, approved December 15, 2007, Standard
 Specification for Concrete Aggregates.
ASTM Standard C 94/C 94M-07, approved January 1, 2007, Standard
 Specification for Ready-Mixed Concrete.
ASTM Standard C 150-07, approved May 1, 2007, Standard Specification for
 Portland Cement.
ASTM Standard C 330-05, approved December 15, 2005, Standard
 Specification for Lightweight Aggregates for Structural Concrete.
ASTM Standard C 595-08, approved January 1, 2008, Standard Specification
 for Blended Hydraulic Cements.
------------------------------------------------------------------------

Reaffirmed Documents

    The reaffirmed documents incorporated by reference in this final 
rule are:

[[Page 22221]]



------------------------------------------------------------------------
                           Title of Documents
-------------------------------------------------------------------------
API MPMS, Chapter 2--Tank Calibration, Section 2A--Measurement and
 Calibration of Upright Cylindrical Tanks by the Manual Tank Strapping
 Method, First Edition, February 1995; reaffirmed February 2007, Order
 No. 852-022A1.
API MPMS, Chapter 2--Tank Calibration, Section 2B--Calibration of
 Upright Cylindrical Tanks Using the Optical Reference Line Method,
 First Edition, March 1989; reaffirmed, December 2007, Order No. H30023.
API MPMS, Chapter 3--Tank Gauging, Section 1B--Standard Practice for
 Level Measurement of Liquid Hydrocarbons in Stationary Tanks by
 Automatic Tank Gauging, Second Edition, June 2001; reaffirmed, October
 2006, Product No. H301B2.
API MPMS, Chapter 4--Proving Systems, Section 4--Tank Provers, Second
 Edition, May 1998; reaffirmed November 2005, Order No. H04042.
API MPMS, Chapter 4--Proving Systems, Section 5--Master-Meter Provers,
 Second Edition, May 2000; reaffirmed: August 2005, Order No. H04052.
API MPMS, Chapter 6--Metering Assemblies, Section 1--Lease Automatic
 Custody Transfer (LACT) Systems, Second Edition, May 1991; reaffirmed,
 April 2007, Order No. H30121.
API MPMS, Chapter 6--Metering Assemblies, Section 6--Pipeline Metering
 Systems, Second Edition, May 1991; reaffirmed, February 2007, Order No.
 852-30126.
API MPMS, Chapter 6--Metering Assemblies, Section 7--Metering Viscous
 Hydrocarbons, Second Edition, May 1991; reaffirmed, April 2007, Order
 No. 852-30127.
API MPMS, Chapter 7--Temperature Determination, First Edition, June
 2001; reaffirmed, March 2007, Product No. H07001.
API MPMS, Chapter 11.2.2-Compressibility Factors for Hydrocarbons: 0.350-
 0.637 Relative Density (60[deg]F/60[deg]F) and -50[deg]F to 140[deg]F
 Metering Temperature, Second Edition, October 1986; reaffirmed December
 2007, Order No. 852-27307.
API MPMS, Chapter 14--Natural Gas Fluids Measurement; Section 3--
 Concentric, Square-Edged Orifice Meters; Part 3--Natural Gas
 Applications; Third Edition, August 1992; Errata March 1994,
 reaffirmed, February 2009, Product No. H143303.
API MPMS, Chapter 14--Natural Gas Fluids Measurement, Section 8--
 Liquefied Petroleum Gas Measurement, Second Edition, July 1997;
 reaffirmed, March 2006, Order No. H14082.
API RP 14C, Recommended Practice for Analysis, Design, Installation, and
 Testing of Basic Surface Safety Systems for Offshore Production
 Platforms, Seventh Edition, March 2001; reaffirmed: March 2007, Product
 No. C14C07.
API RP 14E, Recommended Practice for Design and Installation of Offshore
 Production Platform Piping Systems, Fifth Edition, October 1991;
 reaffirmed, March 2007, Order No. 811-07185.
API RP 14FZ, Recommended Practice for Design and Installation of
 Electrical Systems for Fixed and Floating Offshore Petroleum Facilities
 for Unclassified and Class I, Zone 0, Zone 1 and Zone 2 Locations,
 First Edition, September 2001; reaffirmed: March 2007, Product No.
 G14FZ1.
API RP 14J, Recommended Practice for Design and Hazards Analysis for
 Offshore Production Facilities, Second Edition, May 2001; reaffirmed:
 March 2007, Product No. G14J02.
API Standard 2552, USA Standard Method for Measurement and Calibration
 of Spheres and Spheroids, First Edition, 1966; reaffirmed, October 2007
 (ASTM designation: D 1408-65; date of joint API/ASTM approval, 1965).
------------------------------------------------------------------------

    The purpose of this final rule is to incorporate the revision of 
some documents previously incorporated by reference into MMS 
regulations, and to acknowledge the reaffirmation of other documents 
previously incorporated by reference into MMS regulations.

Procedural Matters

Regulatory Planning and Review (Executive Order (E.O.) 12866)

    This final rule is not a significant rule as determined by the 
Office of Management and Budget (OMB) and is not subject to review 
under E.O. 12866.
    (1) The final rule will not have an annual effect of $100 million 
or more on the economy. It will not adversely affect in a material way 
the economy, productivity, competition, jobs, the environment, public 
health or safety, or State, local, or tribal governments or 
communities. This final rule will not have any new requirements.
    (2) The final rule will not create a serious inconsistency or 
otherwise interfere with an action taken or planned by another agency.
    (3) The final rule will not alter the budgetary effects or 
entitlements, grants, user fees, or loan programs, or the rights or 
obligations of their recipients. The changes in this final rule will 
not impose undue cost on the offshore oil and gas industry.
    (4) The final rule will not raise novel legal or policy issues 
arising out of legal mandates, the President's priorities, or the 
principles set forth in E.O. 12866.

Regulatory Flexibility Act

    The Department of the Interior certifies that this final rule will 
not have a significant economic effect on a substantial number of small 
entities under the Regulatory Flexibility Act (5 U.S.C. 601 et seq.).
    The changes in this final rule will affect lessees and operators of 
leases and pipeline right-of-way holders on the OCS. This could include 
about 130 active Federal oil and gas lessees. Small lessees that 
operate under this rule fall under the Small Business Administration's 
(SBA) North American Industry Classification System (NAICS) codes 
211111, Crude Petroleum and Natural Gas Extraction, and 213111, 
Drilling Oil and Gas Wells. For these NAICS code classifications, a 
small company is one with fewer than 500 employees. Based on these 
criteria, an estimated 70 percent of these companies are considered 
small. This final rule, therefore will affect a substantial number of 
small entities. However, the changes in the rule will not have a 
significant economic effect on a substantial number of small entities 
because it will not impose new costs or burdens on the offshore oil and 
gas industry.
    Your comments are important. The Small Business and Agriculture 
Regulatory Enforcement Ombudsman and 10 Regional Fairness boards were 
established to receive comments from small businesses about Federal 
agency enforcement actions. The Ombudsman will annually evaluate the 
enforcement activities and rate each agency's responsiveness to small 
businesses. If you wish to comment on the actions of MMS, call 1-888-
734-3247. You may comment to the Small Business Administration without 
fear of retaliation. Allegations of discrimination/retaliation filed 
with the Small Business Administration will be investigated for 
appropriate action.

Small Business Regulatory Enforcement Fairness Act

    The final rule is not a major rule under the Small Business 
Regulatory Enforcement Fairness Act (5 U.S.C. 801 et seq.). This final 
rule:
    a. Will not have an annual effect on the economy of $100 million or 
more. The only costs will be the purchase of the new API documents and 
minor

[[Page 22222]]

revisions to some operating and maintenance procedures.
    b. Will not cause a major increase in costs or prices for 
consumers, individual industries, Federal, State, or local government 
agencies, or geographic regions.
    c. Will not have significant adverse effects on competition, 
employment, investment, productivity, innovation, or the ability of 
U.S.-based enterprises to compete with foreign-based enterprises.

Unfunded Mandates Reform Act

    This final rule will not impose an unfunded mandate on State, 
local, and tribal governments or the private sector of more than $100 
million per year. The rule will not have a significant or unique effect 
on State, local, or tribal governments or the private sector. A 
statement containing the information required by the Unfunded Mandates 
Reform Act (2 U.S.C. 1501 et seq.) is not required.

Takings Implication Assessment (E.O. 12630)

    Under the criteria in E.O. 12630, this final rule does not have 
significant takings implications. The final rule is not a governmental 
action capable of interference with constitutionally protected property 
rights. A Takings Implication Assessment is not required.

Federalism (E.O. 13132)

    Under the criteria in E.O. 13132, this final rule does not have 
federalism implications. This final rule will not substantially and 
directly affect the relationship between the Federal and State 
governments. To the extent that State and local governments have a role 
in OCS activities, this final rule will not affect that role. A 
Federalism Assessment is not required.

Civil Justice Reform (E.O. 12988)

    This rule complies with the requirements of E.O. 12988. 
Specifically, this rule:
    (a) Meets the criteria of section 3(a) requiring that all 
regulations be reviewed to eliminate errors and ambiguity and be 
written to minimize litigation; and
    (b) Meets the criteria of section 3(b)(2) requiring that all 
regulations be written in clear language and contain clear legal 
standards.

Consultation With Indian Tribes (Executive Order 13175)

    Under the criteria in E.O. 13175, we have evaluated this rule and 
determined that it has no substantial effects on federally recognized 
Indian tribes.

Paperwork Reduction Act (PRA) of 1995

    This rulemaking does not contain any information collection 
requirements and does not require a submission to Office of Management 
and Budget for review and approval subject to the Paperwork Reduction 
Act of 1995 (44 U.S.C. 3501 et seq.).

National Environmental Policy Act (NEPA) of 1969

    This rule does not constitute a major Federal action significantly 
affecting the quality of the human environment. A detailed statement 
under the NEPA of 1969 is not required because the rule is covered by a 
categorical exclusion. The MMS has analyzed this rule under the 
criteria of the NEPA and 516 Departmental Manual Chapter 15.4.C(1). We 
have also determined that the rule does not involve any of the 
extraordinary circumstances listed in 43 CFR 42.215 that would require 
further analysis under the NEPA.

Data Quality Act

    In developing this rule, we did not conduct or use a study, 
experiment, or survey requiring peer review under the Data Quality Act 
(Pub. L. 106-554, app. C Sec.  515, 114 Stat. 2763, 2763A-153-154).

Effects on the Energy Supply (E.O. 13211)

    This rule is not a significant energy action under the definition 
in E.O. 13211. A Statement of Energy Effects is not required.

List of Subjects in 30 CFR Part 250

    Continental shelf, Incorporation by reference, Oil and gas 
exploration, Pipelines, Public lands--mineral resources, Reporting and 
recordkeeping requirements.

    Dated: March 11, 2010.
Ned Farquhar,
Deputy Assistant Secretary--Land and Minerals Management.

0
For the reasons stated in the preamble, Minerals Management Service 
(MMS) is amending 30 CFR part 250 as follows:

PART 250--OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER 
CONTINENTAL SHELF

0
1. The authority citation for part 250 continues to read as follows:

    Authority: 31 U.S.C. 9701, 43 U.S.C. 1334.

0
2. Revise Sec.  250.198 to read as follows:


Sec.  250.198  Documents incorporated by reference.

    (a) The MMS is incorporating by reference the documents listed in 
paragraphs (e) through (k) of this section. Paragraphs (e) through (k) 
identify the publishing organization of the documents, the address and 
phone number where you may obtain these documents, and the documents 
incorporated by reference. The Director of the Federal Register has 
approved the incorporations by reference according to 5 U.S.C. 552(a) 
and 1 CFR part 51.
    (1) Incorporation by reference of a document is limited to the 
edition of the publication that is cited in this section. Future 
amendments or revisions of the document are not included. The MMS will 
publish any changes to a document in the Federal Register and amend 
this section.
    (2) The MMS may make the rule amending the document effective 
without prior opportunity for public comment when MMS determines:
    (i) That the revisions to a document result in safety improvements 
or represent new industry standard technology and do not impose undue 
costs on the affected parties; and
    (ii) The MMS meets the requirements for making a rule immediately 
effective under 5 U.S.C. 553.
    (b) The MMS incorporated each document or specific portion by 
reference in the sections noted. The entire document is incorporated by 
reference, unless the text of the corresponding sections in this part 
calls for compliance with specific portions of the listed documents. In 
each instance, the applicable document is the specific edition or 
specific edition and supplement or addendum cited in this section.
    (c) Under Sec. Sec.  250.141 and 250.142, you may comply with a 
later edition of a specific document incorporated by reference, 
provided:
    (1) You show that complying with the later edition provides a 
degree of protection, safety, or performance equal to or better than 
would be achieved by compliance with the listed edition; and
    (2) You obtain the prior written approval for alternative 
compliance from the authorized MMS official.
    (d) You may inspect these documents at the Minerals Management 
Service, 381 Elden Street, Room 3313, Herndon, Virginia 20170; phone: 
703-787-1587; or at the National Archives and Records Administration 
(NARA). For information on the availability of this material at NARA, 
call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.
    (e) American Concrete Institute (ACI), ACI Standards, P. O. Box 
9094, Farmington Hill, MI 48333-9094:

[[Page 22223]]

http://www.concrete.org; phone: 248-848-3700:
    (1) ACI Standard 318-95, Building Code Requirements for Reinforced 
Concrete (ACI 318-95) and Commentary (ACI 318R-95), incorporated by 
reference at Sec.  250.901(a), (d).
    (2) ACI 357R-84, Guide for the Design and Construction of Fixed 
Offshore Concrete Structures, 1984; reapproved 1997, incorporated by 
reference at Sec.  250.901(a), (d).
    (f) American Institute of Steel Construction, Inc. (AISC), AISC 
Standards, One East Wacker Drive, Suite 700, Chicago, IL 60601-1802; 
http://www.aisc.org; phone: 312-670-2400:
    (1) ANSI/AISC 360-05, Specification for Structural Steel Buildings 
incorporated by reference at Sec.  250.901(a), (d).
    (2) [Reserved]
    (g) American National Standards Institute (ANSI), ANSI/ASME Codes, 
ATTN: Sales Department, 25 West 43rd Street, 4th Floor, New York, NY 
10036; http://www.ansi.org; phone: 212-642-4900; and/or American 
Society of Mechanical Engineers (ASME), 22 Law Drive, P.O. Box 2900, 
Fairfield, NJ 07007-2900; http://www.asme.org; phone: 973-882-5155:
    (1) ANSI/ASME Boiler and Pressure Vessel Code, Section I, Rules for 
Construction of Power Boilers; including Appendices, 2004 Edition; and 
July 1, 2005 Addenda, and all Section I Interpretations Volume 55, 
incorporated by reference at Sec.  250.803(b)(1), (b)(1)(i); and Sec.  
250.1629(b)(1), (b)(1)(i);
    (2) ANSI/ASME Boiler and Pressure Vessel Code, Section IV, Rules 
for Construction of Heating Boilers; including Appendices 1, 2, 3, 5, 
6, and Non-mandatory Appendices B, C, D, E, F, H, I, K, L, and M, and 
the Guide to Manufacturers Data Report Forms, 2004 Edition; July 1, 
2005 Addenda, and all Section IV Interpretations Volume 55, 
incorporated by reference at Sec.  250.803(b)(1), (b)(1)(i); and Sec.  
250.1629(b)(1), (b)(1)(i);
    (3) ANSI/ASME Boiler and Pressure Vessel Code, Section VIII, Rules 
for Construction of Pressure Vessels; Divisions 1 and 2, 2004 Edition; 
July 1, 2005 Addenda, Divisions 1 and 2, and all Section VIII 
Interpretations Volumes 54 and 55, incorporated by reference at Sec.  
250.803(b)(1), (b)(1)(i); and Sec.  250.1629(b)(1), (b)(1)(i);
    (4) ANSI/ASME B 16.5-2003, Pipe Flanges and Flanged Fittings 
incorporated by reference at Sec.  250.1002(b)(2);
    (5) ANSI/ASME B 31.8-2003, Gas Transmission and Distribution Piping 
Systems incorporated by reference at Sec.  250.1002(a);
    (6) ANSI/ASME SPPE-1-1994 and SPPE-1d-1996 Addenda, Quality 
Assurance and Certification of Safety and Pollution Prevention 
Equipment Used in Offshore Oil and Gas Operations, incorporated by 
reference at Sec.  250.806(a)(2)(i);
    (7) ANSI Z88.2-1992, American National Standard for Respiratory 
Protection, incorporated by reference at, Sec.  250.490(g)(4)(iv), 
(j)(13)(ii).
    (h) American Petroleum Institute (API), API Recommended Practices 
(RP), Specs, Standards, Manual of Petroleum Measurement Standards 
(MPMS) chapters, 1220 L Street, NW., Washington, DC 20005-4070; http://www.api.org; phone: 202-682-8000:
    (1) API 510, Pressure Vessel Inspection Code: In-Service 
Inspection, Rating, Repair, and Alteration, Downstream Segment, Ninth 
Edition, June 2006, Product No. C51009; incorporated by reference at 
Sec.  250.803(b)(1); and Sec.  250.1629(b)(1);
    (2) API Bulletin 2INT-DG, Interim Guidance for Design of Offshore 
Structures for Hurricane Conditions, May 2007, Product No. G2DGINT; 
incorporated by reference at Sec.  250.901(a), (d);
    (3) API Bulletin 2INT-EX, Interim Guidance for Assessment of 
Existing Offshore Structures for Hurricane Conditions, May 2007, 
Product No. G2EXINT; incorporated by reference at Sec.  250.901(a), 
(d);
    (4) API Bulletin 2INT-MET, Interim Guidance on Hurricane Conditions 
in the Gulf of Mexico, May 2007, Product No. G2INTMET; incorporated by 
reference at Sec.  250.901(a), (d);
    (5) API MPMS, Chapter 1--Vocabulary, Second Edition, July 1994, 
Order No. 852-01002; incorporated by reference at Sec.  250.1201;
    (6) API MPMS, Chapter 2--Tank Calibration, Section 2A--Measurement 
and Calibration of Upright Cylindrical Tanks by the Manual Tank 
Strapping Method, First Edition, February 1995; reaffirmed February 
2007, Order No. 852-022A1; incorporated by reference at Sec.  
250.1202(l)(4);
    (7) API MPMS, Chapter 2--Tank Calibration, Section 2B--Calibration 
of Upright Cylindrical Tanks Using the Optical Reference Line Method, 
First Edition, March 1989; reaffirmed, December 2007, Order No. H30023; 
incorporated by reference at Sec.  250.1202(l)(4);
    (8) API MPMS, Chapter 3--Tank Gauging, Section 1A--Standard 
Practice for the Manual Gauging of Petroleum and Petroleum Products, 
Second Edition, August 2005, Product No. H301A02; incorporated by 
reference at Sec.  250.1202(l)(4);
    (9) API MPMS, Chapter 3--Tank Gauging, Section 1B--Standard 
Practice for Level Measurement of Liquid Hydrocarbons in Stationary 
Tanks by Automatic Tank Gauging, Second Edition, June 2001, reaffirmed, 
October 2006, Product No. H301B2; incorporated by reference at Sec.  
250.1202(l)(4);
    (10) API MPMS, Chapter 4--Proving Systems, Section 1--Introduction, 
Third Edition, February 2005, Product No. H04013; incorporated by 
reference at Sec.  250.1202(a)(3), (f)(1);
    (11) API MPMS, Chapter 4--Proving Systems, Section 2--Displacement 
Provers, Third Edition, September 2003, Product No. H04023; 
incorporated by reference at Sec.  250.1202(a)(3), (f)(1);
    (12) API MPMS, Chapter 4--Proving Systems, Section 4--Tank Provers, 
Second Edition, May 1998, reaffirmed November 2005, Order No. H04042; 
incorporated by reference at Sec.  250.1202(a)(3), (f)(1);
    (13) API MPMS, Chapter 4--Proving Systems, Section 5--Master-Meter 
Provers, Second Edition, May 2000, reaffirmed: August 2005, Order No. 
H04052; incorporated by reference at Sec.  250.1202(a)(3), (f)(1);
    (14) API MPMS, Chapter 4--Proving Systems, Section 6--Pulse 
Interpolation, Second Edition, May 1999; reaffirmed 2003, Order No. 
H04062; incorporated by reference at Sec.  250.1202(a)(3), (f)(1);
    (15) API MPMS, Chapter 4--Proving Systems, Section 7--Field 
Standard Test Measures, Second Edition, December 1998; reaffirmed 2003, 
Order No. H04072; incorporated by reference at Sec.  250.1202(a)(3), 
(f)(1);
    (16) API MPMS, Chapter 5--Metering, Section 1--General 
Considerations for Measurement by Meters, Fourth Edition, September 
2005, Product No. H05014; incorporated by reference at Sec.  
250.1202(a)(3);
    (17) API MPMS, Chapter 5--Metering, Section 2--Measurement of 
Liquid Hydrocarbons by Displacement Meters, Third Edition, September 
2005, Product No. H05023; incorporated by reference at Sec.  
250.1202(a)(3);
    (18) API MPMS Chapter 5--Metering, Section 3--Measurement of Liquid 
Hydrocarbons by Turbine Meters, Fifth Edition, September 2005, Product 
No. H05035; incorporated by reference at Sec.  250.1202(a)(3);
    (19) API MPMS, Chapter 5--Metering, Section 4--Accessory Equipment 
for Liquid Meters, Fourth Edition, September 2005, Product No. H05044; 
incorporated by reference at Sec.  250.1202(a)(3);
    (20) API MPMS, Chapter 5--Metering, Section 5--Fidelity and 
Security of

[[Page 22224]]

Flow Measurement Pulsed-Data Transmission Systems, Second Edition, 
August 2005, Product No. H50502; incorporated by reference at Sec.  
250.1202(a)(3);
    (21) API MPMS, Chapter 6--Metering Assemblies, Section 1--Lease 
Automatic Custody Transfer (LACT) Systems, Second Edition, May 1991; 
reaffirmed, April 2007, Order No. H30121; incorporated by reference at 
Sec.  250.1202(a)(3);
    (22) API MPMS, Chapter 6--Metering Assemblies, Section 6--Pipeline 
Metering Systems, Second Edition, May 1991; reaffirmed, February 2007, 
Order No. 852-30126; incorporated by reference at Sec.  250.1202(a)(3);
    (23) API MPMS, Chapter 6--Metering Assemblies, Section 7--Metering 
Viscous Hydrocarbons, Second Edition, May 1991; reaffirmed, April 2007, 
Order No. 852-30127; incorporated by reference at Sec.  250.1202(a)(3);
    (24) API MPMS, Chapter 7--Temperature Determination, First Edition, 
June 2001; reaffirmed, March 2007; Product No. H07001; incorporated by 
reference at Sec.  250.1202(a)(3), (l)(4);
    (25) API MPMS, Chapter 8--Sampling, Section 1--Standard Practice 
for Manual Sampling of Petroleum and Petroleum Products, Third Edition, 
October 1995; reaffirmed, March 2006, Order No. H08013; incorporated by 
reference at Sec.  250.1202(b)(4)(i), (l)(4);
    (26) API MPMS, Chapter 8--Sampling, Section 2--Standard Practice 
for Automatic Sampling of Liquid Petroleum and Petroleum Products, 
Second Edition, October 1995; reaffirmed, June 2005, Order No. H08022; 
incorporated by reference at Sec.  250.1202(a)(3), (l)(4);
    (27) API MPMS, Chapter 9--Density Determination, Section 1--
Standard Test Method for Density, Relative Density (Specific Gravity), 
or API Gravity of Crude Petroleum and Liquid Petroleum Products by 
Hydrometer Method, Second Edition, December 2002; reaffirmed October 
2005, Product No. H09012; incorporated by reference at Sec.  
250.1202(a)(3), (l)(4);
    (28) API MPMS, Chapter 9--Density Determination, Section 2--
Standard Test Method for Density or Relative Density of Light 
Hydrocarbons by Pressure Hydrometer, Second Edition, March 2003, 
Product No. H09022; incorporated by reference at Sec.  250.1202(a)(3), 
(l)(4);
    (29) API MPMS, Chapter 10--Sediment and Water, Section 1--Standard 
Test Method for Sediment in Crude Oils and Fuel Oils by the Extraction 
Method, Third Edition, November 2007, Product No. H10013; incorporated 
by reference at Sec.  250.1202(a)(3), (l)(4);
    (30) API MPMS, Chapter 10--Sediment and Water, Section 2--Standard 
Test Method for Water in Crude Oil by Distillation, Second Edition, 
November 2007, Product No. H10022; incorporated by reference at Sec.  
250.1202(a)(3), (l)(4);
    (31) API MPMS, Chapter 10--Sediment and Water, Section 3--Standard 
Test Method for Water and Sediment in Crude Oil by the Centrifuge 
Method (Laboratory Procedure), Third Edition, May 2008, Product No. 
H10033; incorporated by reference at Sec.  250.1202(a)(3), (l)(4);
    (32) API MPMS, Chapter 10--Sediment and Water, Section 4--
Determination of Water and/or Sediment in Crude Oil by the Centrifuge 
Method (Field Procedure), Third Edition, December 1999, Order No. 
H10043; incorporated by reference at Sec.  250.1202(a)(3), (l)(4);
    (33) API MPMS, Chapter 10--Sediment and Water, Section 9--Standard 
Test Method for Water in Crude Oils by Coulometric Karl Fischer 
Titration, Second Edition, December 2002; reaffirmed 2005, Product No. 
H10092; incorporated by reference at Sec.  250.1202(a)(3), (l)(4);
    (34) API MPMS, Chapter 11.1--Volume Correction Factors, Volume 1, 
Table 5A--Generalized Crude Oils and JP-4 Correction of Observed API 
Gravity to API Gravity at 60 [deg]F, and Table 6A--Generalized Crude 
Oils and JP-4 Correction of Volume to 60 [deg]F Against API Gravity at 
60 [deg]F, API Standard 2540, First Edition, August 1980; reaffirmed 
March 1997, API Stock No. H27000; incorporated by reference at Sec.  
250.1202(a)(3), (g)(3), (l)(4);
    (35) API MPMS, Chapter 11.2.2--Compressibility Factors for 
Hydrocarbons: 0.350-0.637 Relative Density (60 [deg]F/60 [deg]F) and -
50 [deg]F to 140 [deg]F Metering Temperature, Second Edition, October 
1986; reaffirmed: December 2007, Order No. 852-27307; incorporated by 
reference at Sec.  250.1202(a)(3), (g)(4);
    (36) API MPMS, Chapter 11--Physical Properties Data, Addendum to 
Section 2, Part 2--Compressibility Factors for Hydrocarbons, 
Correlation of Vapor Pressure for Commercial Natural Gas Liquids, First 
Edition, December 1994; reaffirmed, December 2002, Order No. H27308; 
incorporated by reference at Sec.  250.1202(a)(3);
    (37) API MPMS, Chapter 12--Calculation of Petroleum Quantities, 
Section 2--Calculation of Petroleum Quantities Using Dynamic 
Measurement Methods and Volumetric Correction Factors, Part 1--
Introduction, Second Edition, May 1995; reaffirmed March 2002, Order 
No. H12021; incorporated by reference at Sec.  250.1202(a)(3), (g)(1), 
(g)(2);
    (38) API MPMS, Chapter 12--Calculation of Petroleum Quantities, 
Section 2--Calculation of Petroleum Quantities Using Dynamic 
Measurement Methods and Volumetric Correction Factors, Part 2--
Measurement Tickets, Third Edition, June 2003, Product No. H12223; 
incorporated by reference at Sec.  250.1202(a)(3), (g)(1), (g)(2);
    (39) API MPMS, Chapter 14--Natural Gas Fluids Measurement, Section 
3--Concentric, Square-Edged Orifice Meters, Part 1--General Equations 
and Uncertainty Guidelines, Third Edition, September 1990; reaffirmed 
January 2003, Order No. 852-30350; incorporated by reference at Sec.  
250.1203(b)(2);
    (40) API MPMS, Chapter 14--Natural Gas Fluids Measurement, Section 
3--Concentric, Square-Edged Orifice Meters, Part 2--Specification and 
Installation Requirements, Fourth Edition, April 2000; reaffirmed March 
2006, Order No. H14324; incorporated by reference at Sec.  
250.1203(b)(2);
    (41) API MPMS, Chapter 14--Natural Gas Fluids Measurement, Section 
3--Concentric, Square-Edged Orifice Meters; Part 3--Natural Gas 
Applications; Third Edition, August 1992; Errata March 1994, 
reaffirmed, February 2009, Product No. H143303; incorporated by 
reference at Sec.  250.1203(b)(2);
    (42) API MPMS, Chapter 14.5/GPA Standard 2172-09; Calculation of 
Gross Heating Value, Relative Density, Compressibility and Theoretical 
Hydrocarbon Liquid Content for Natural Gas Mixtures for Custody 
Transfer; Third Edition, January 2009; Adopted as Tentative Standard, 
1972; Revised and Adopted as Standard, 1976; Revised 1984, 1986, 1996, 
2009; Product No. H140503; incorporated by reference at Sec.  
250.1203(b)(2);
    (43) API MPMS, Chapter 14--Natural Gas Fluids Measurement, Section 
6--Continuous Density Measurement, Second Edition, April 1991; 
reaffirmed, February 2006, Order No. H30346; incorporated by reference 
at Sec.  250.1203(b)(2);
    (44) API MPMS, Chapter 14--Natural Gas Fluids Measurement, Section 
8--Liquefied Petroleum Gas Measurement, Second Edition, July 1997; 
reaffirmed, March 2006, Order No. H14082; incorporated by reference at 
Sec.  250.1203(b)(2);
    (45) API MPMS, Chapter 20--Section 1--Allocation Measurement, First 
Edition, September 1993; reaffirmed October 2006, Order No. 852-30701;

[[Page 22225]]

incorporated by reference at Sec.  250.1202(k)(1);
    (46) API MPMS, Chapter 21--Flow Measurement Using Electronic 
Metering Systems, Section 1--Electronic Gas Measurement, First Edition, 
August 1993; reaffirmed, July 2005, Order No. 852-30730; incorporated 
by reference at Sec.  250.1203(b)(4);
    (47) API RP 2A-WSD, Recommended Practice for Planning, Designing 
and Constructing Fixed Offshore Platforms--Working Stress Design, 
Twenty-first Edition, December 2000; Errata and Supplement 1, December 
2002; Errata and Supplement 2, September 2005; Errata and Supplement 3, 
October 2007; Product No. G2AWSD; incorporated by reference at Sec.  
250.901(a), (d); Sec.  250.908(a); Sec.  250.919(b)(2); Sec.  
250.920(a), (b), (c), (d), (e), (f);
    (48) API RP 2D, Operation and Maintenance of Offshore Cranes, Sixth 
Edition, May 2007, Product No. G02D06; incorporated by reference at 
Sec.  250.108(a);
    (49) API RP 2FPS, RP for Planning, Designing, and Constructing 
Floating Production Systems; First Edition, March 2001, Order No. 
G2FPS1; incorporated by reference at Sec.  250.901(a), (d);
    (50) API RP 2I, In-Service Inspection of Mooring Hardware for 
Floating Structures; Third Edition, April 2008, Product No. G02I03; 
incorporated by reference at Sec.  250.901(a), (d);
    (51) API RP 2RD, Recommended Practice for Design of Risers for 
Floating Production Systems (FPSs) and Tension-Leg Platforms (TLPs), 
First Edition, June 1998; reaffirmed, May 2006, Errata, June 2009; 
Order No. G02RD1; incorporated by reference at Sec.  250.800(b)(2); 
Sec.  250.901(a), (d); Sec.  250.1002(b)(5);
    (52) API RP 2SK, Design and Analysis of Stationkeeping Systems for 
Floating Structures, Third Edition, October 2005, Addendum, May 2008, 
Product No. G2SK03; incorporated by reference at Sec.  250.800(b)(3); 
Sec.  250.901(a), (d);
    (53) API RP 2SM, Recommended Practice for Design, Manufacture, 
Installation, and Maintenance of Synthetic Fiber Ropes for Offshore 
Mooring, First Edition, March 2001, Addendum, May 2007, Product No. 
G02SM1; incorporated by reference at Sec.  250.901(a), (d);
    (54) API RP 2T, Recommended Practice for Planning, Designing, and 
Constructing Tension Leg Platforms, Second Edition, August 1997, Order 
No. G02T02; incorporated by reference at Sec.  250.901(a), (d);
    (55) API RP 14B, Recommended Practice for Design, Installation, 
Repair and Operation of Subsurface Safety Valve Systems, Fifth Edition, 
October 2005, also available as ISO 10417: 2004, (Identical) Petroleum 
and natural gas industries--Subsurface safety valve systems--Design, 
installation, operation and redress, Product No. GX14B05; incorporated 
by reference at Sec.  250.801(e)(4); Sec.  250.804(a)(1)(i);
    (56) API RP 14C, Recommended Practice for Analysis, Design, 
Installation, and Testing of Basic Surface Safety Systems for Offshore 
Production Platforms, Seventh Edition, March 2001, reaffirmed: March 
2007; Product No. C14C07; incorporated by reference at Sec.  
250.125(a); Sec.  250.292(j); Sec.  250.802(b), (e)(2); Sec.  
250.803(a), (b)(2)(i), (b)(4), (b)(5)(i), (b)(7), (b)(9)(v), (c)(2); 
Sec.  250.804(a), (a)(6); Sec.  250.1002(d); Sec.  250.1004(b)(9); 
Sec.  250.1628(c), (d)(2); Sec.  250.1629(b)(2), (b)(4)(v); Sec.  
250.1630(a);
    (57) API RP 14E, Recommended Practice for Design and Installation 
of Offshore Production Platform Piping Systems, Fifth Edition, October 
1991; reaffirmed, March 2007, Order No. 811-07185; incorporated by 
reference at Sec.  250.802(e)(3); Sec.  250.1628(b)(2), (d)(3);
    (58) API RP 14F, Design, Installation, and Maintenance of 
Electrical Systems for Fixed and Floating Offshore Petroleum Facilities 
for Unclassified and Class I, Division 1 and Division 2 Locations, 
Fifth Edition, July 2008, Product No. G14F05; incorporated by reference 
at Sec.  250.114(c); Sec.  250.803(b)(9)(v); Sec.  250.1629(b)(4)(v);
    (59) API RP 14FZ, Recommended Practice for Design and Installation 
of Electrical Systems for Fixed and Floating Offshore Petroleum 
Facilities for Unclassified and Class I, Zone 0, Zone 1 and Zone 2 
Locations, First Edition, September 2001, reaffirmed: March 2007; 
Product No. G14FZ1; incorporated by reference at Sec.  250.114(c); 
Sec.  250.803(b)(9)(v); Sec.  250.1629(b)(4)(v);
    (60) API RP 14G, Recommended Practice for Fire Prevention and 
Control on Fixed Open-type Offshore Production Platforms, Fourth 
Edition, April 2007; Product No. G14G04; incorporated by reference at 
Sec.  250.803(b)(8), (b)(9)(v); Sec.  250.1629(b)(3), (b)(4)(v);
    (61) API RP 14H, Recommended Practice for Installation, Maintenance 
and Repair of Surface Safety Valves and Underwater Safety Valves 
Offshore, Fifth Edition, August 2007, Product No. G14H05; incorporated 
by reference at Sec.  250.802(d); Sec.  250.804(a)(5);
    (62) API RP 14J, Recommended Practice for Design and Hazards 
Analysis for Offshore Production Facilities, Second Edition, May 2001; 
reaffirmed: March 2007; Product No. G14J02; incorporated by reference 
at Sec.  250.800(b)(1); Sec.  250.901(a)(14);
    (63) API RP 53, Recommended Practices for Blowout Prevention 
Equipment Systems for Drilling Wells, Third Edition, March 1997; 
reaffirmed September 2004, Order No. G53003; incorporated by reference 
at Sec.  250.442(c); Sec.  250.446(a);
    (64) API RP 65, Recommended Practice for Cementing Shallow Water 
Flow Zones in Deepwater Wells, First Edition, September 2002, Product 
No. G56001; incorporated by reference at Sec.  250.415(e);
    (65) API RP 500, Recommended Practice for Classification of 
Locations for Electrical Installations at Petroleum Facilities 
Classified as Class I, Division 1 and Division 2, Second Edition, 
November 1997; reaffirmed November 2002, Product No. C50002; 
incorporated by reference at Sec.  250.114(a); Sec.  250.459; Sec.  
250.802(e)(4)(i); Sec.  250.803(b)(9)(i); Sec.  250.1628(b)(3), 
(d)(4)(i); Sec.  250.1629(b)(4)(i);
    (66) API RP 505, Recommended Practice for Classification of 
Locations for Electrical Installations at Petroleum Facilities 
Classified as Class I, Zone 0, Zone 1, and Zone 2, First Edition, 
November 1997; reaffirmed November 2002, Order No. C50501; incorporated 
by reference at Sec.  250.114(a); Sec.  250.459; Sec.  
250.802(e)(4)(i); Sec.  250.803(b)(9)(i); Sec.  250.1628(b)(3), 
(d)(4)(i); Sec.  250.1629(b)(4)(i);
    (67) API RP 2556, Recommended Practice for Correcting Gauge Tables 
for Incrustation, Second Edition, August 1993; reaffirmed November 
2003, Order No. H25560; incorporated by reference at Sec.  
250.1202(l)(4);
    (68) ANSI/API Spec. Q1, Specification for Quality Programs for the 
Petroleum, Petrochemical and Natural Gas Industry, ISO TS 29001:2007 
(Identical), Petroleum, petrochemical and natural gas industries--
Sector specific requirements--Requirements for product and service 
supply organizations, Eighth Edition, December 2007, Effective Date: 
June 15, 2008, Product No. GXQ108; incorporated by reference at Sec.  
250.806(a)(2)(ii);
    (69) API Spec. 2C, Specification for Offshore Pedestal Mounted 
Cranes, Sixth Edition, March 2004, Effective Date: September 2004, 
Product No. G02C06; incorporated by reference at Sec.  250.108(c), (d);
    (70) ANSI/API Spec. 6A, Specification for Wellhead and Christmas 
Tree Equipment, Nineteenth Edition, July 2004; Effective Date: February 
1, 2005; Contains API Monogram Annex as Part of U.S. National Adoption; 
ISO 10423:2003 (Modified), Petroleum and natural gas industries--
Drilling and

[[Page 22226]]

production equipment--Wellhead and Christmas tree equipment; Errata 1, 
September 2004, Errata 2, April 2005, Errata 3, June 2006, Errata 4, 
August 2007, Errata 5, May 2009; Addendum 1, February 2008; Addendum 2, 
3, and 4, December 2008; Product No. GX06A19; incorporated by reference 
at Sec.  250.806(a)(3); Sec.  250.1002(b)(1), (b)(2);
    (71) API Spec. 6AV1, Specification for Verification Test of 
Wellhead Surface Safety Valves and Underwater Safety Valves for 
Offshore Service, First Edition, February 1, 1996; reaffirmed January 
2003, Order No. G06AV1; incorporated by reference at Sec.  
250.806(a)(3);
    (72) ANSI/API Spec. 6D, Specification for Pipeline Valves, Twenty-
third Edition, April 2008; Effective Date: October 1, 2008, Errata 1, 
June 2008; Errata 2, November 2008; Errata 3, February 2009; Addendum 
1, October 2009; Contains API Monogram Annex as Part of U.S. National 
Adoption; ISO 14313:2007 (Identical), Petroleum and natural gas 
industries--Pipeline transportation systems--Pipeline valves; Product 
No. GX6D23; incorporated by reference at Sec.  250.1002(b)(1);
    (73) ANSI/API Spec. 14A, Specification for Subsurface Safety Valve 
Equipment, Eleventh Edition, October 2005, Effective Date: May 1, 2006; 
also available as ISO 10432:2004, Product No. GX14A11; incorporated by 
reference at Sec.  250.806(a)(3);
    (74) ANSI/API Spec. 17J, Specification for Unbonded Flexible Pipe, 
Third Edition, July 2008; Effective Date: January 1, 2009, Contains API 
Monogram Annex as Part of U.S. National Adoption; ISO 13628-2:2006 
(Identical), Petroleum and natural gas industries--Design and operation 
of subsea production systems--Part 2: Unbonded flexible pipe systems 
for subsea and marine application; Product No. GX17J03; incorporated by 
reference at Sec.  250.803(b)(2)(iii); Sec.  250.1002(b)(4); Sec.  
250.1007(a)(4);
    (75) API Standard 2551, Measurement and Calibration of Horizontal 
Tanks, First Edition, 1965; reaffirmed March 2002, API Stock No. 
H25510; incorporated by reference at Sec.  250.1202(l)(4);
    (76) API Standard 2552, USA Standard Method for Measurement and 
Calibration of Spheres and Spheroids, First Edition, 1966; reaffirmed, 
October 2007 (ASTM designation: D 1408-65; date of joint API/ASTM 
approval, 1965); incorporated by reference at Sec.  250.1202(l)(4);
    (77) API Standard 2555, Method for Liquid Calibration of Tanks, 
First Edition, September 1966; reaffirmed March 2002; Order No. 852-
25550; incorporated by reference at Sec.  250.1202(l)(4).
    (i) American Society for Testing and Materials (ASTM), ASTM 
Standards, 100 Bar Harbor Drive, P. O. Box C700, West Conshohocken, PA 
19428-2959; http://www.astm.org; phone: 610-832-9500:
    (1) ASTM Standard C 33-07, approved December 15, 2007, Standard 
Specification for Concrete Aggregates; incorporated by reference at 
Sec.  250.901(a), (d);
    (2) ASTM Standard C 94/C 94M-07, approved January 1, 2007, Standard 
Specification for Ready-Mixed Concrete; incorporated by reference at 
Sec.  250.901(a), (d);
    (3) ASTM Standard C 150-07, approved May 1, 2007, Standard 
Specification for Portland Cement; incorporated by reference at Sec.  
250.901(a), (d);
    (4) ASTM Standard C 330-05, approved December 15, 2005, Standard 
Specification for Lightweight Aggregates for Structural Concrete; 
incorporated by reference at Sec.  250.901(a), (d);
    (5) ASTM Standard C 595-08, approved January 1, 2008, Standard 
Specification for Blended Hydraulic Cements; incorporated by reference 
at Sec.  250.901(a), (d);
    (j) American Welding Society (AWS), AWS Codes, 550 NW, LeJeune 
Road, Miami, FL 33126; http://www.aws.org; phone: 800-443-9353:
    (1) AWS D1.1:2000, Structural Welding Code--Steel; incorporated by 
reference at Sec.  250.901(a), (d);
    (2) AWS D1.4-98, Structural Welding Code--Reinforcing Steel; 
incorporated by reference at Sec.  250.901(a), (d);
    (3) AWS D3.6M:1999, Specification for Underwater Welding; 
incorporated by reference at Sec.  250.901(a), (d).
    (k) National Association of Corrosion Engineers (NACE), NACE 
Standards, 1440 South Creek Drive, Houston, TX 77084; http://www.nace.org; phone: 281-228-6200:
    (1) NACE Standard MR0175-2003, Item No. 21302, Standard Material 
Requirements, Metals for Sulfide Stress Cracking and Stress Corrosion 
Cracking Resistance in Sour Oilfield Environments; incorporated by 
reference at Sec.  250.901(a), Sec.  250.490(p)(2);
    (2) NACE Standard RP0176-2003, Item No. 21018, Standard Recommended 
Practice, Corrosion Control of Steel Fixed Offshore Structures 
Associated with Petroleum Production; incorporated by reference at 
Sec.  250.901(a), (d).

0
3. Amend Sec.  250.803(b)(1) introductory text by revising the last 
sentence to read as follows:


Sec.  250.803  Additional production system requirements.

* * * * *
    (b) * * *
    (1) * * * Pressure and fired vessels must have maintenance 
inspection, rating, repair, and alteration performed in accordance with 
the applicable provisions of API Pressure Vessel Inspections Code: In-
Service Inspection, Rating, Repair, and Alteration, API 510 (except 
Sections 5.8 and 9.5) (incorporated by reference as specified in Sec.  
250.198).
* * * * *

0
4. Amend Sec.  250.806 by revising paragraph (a)(2)(i) to read as 
follows:


Sec.  250.806  Safety and pollution prevention equipment quality 
assurance requirements.

    (a) * * *
    (2) * * *
    (i) ANSI/ASME SPPE-1-1994 and SPPE-1d-1996 Addenda, Quality 
Assurance and Certification of Safety and Pollution Prevention 
Equipment Used in Offshore Oil and Gas Operations; and
* * * * *

0
5. Amend Sec.  250.901 by:
0
A. Revising paragraph (a)(1) and (a)(2);
0
B. Revising (a)(15) through (a)(19), and
0
C. Revising paragraphs (d)(1), (d)(7) through (d)(11), and (d)(16) in 
the table to read as follows:


Sec.  250.901  What industry standards must your platform meet?

* * * * *
    (a) * * *
    (1) ACI Standard 318-95, Building Code Requirements for Reinforced 
Concrete (ACI 318-95) and Commentary (ACI 318R-95) (incorporated by 
reference at Sec.  250.198);
    (2) ACI 357R-84, Guide for the Design and Construction of Fixed 
Offshore Concrete Structures, 1984; reapproved 1997 (incorporated by 
reference at Sec.  250.198);
* * * * *
    (15) American Society for Testing and Materials (ASTM) Standard C 
33-07, approved December 15, 2007, Standard Specification for Concrete 
Aggregates (incorporated by reference as specified in Sec.  250.198);
    (16) ASTM Standard C 94/C 94M-07, approved January 1, 2007, 
Standard Specification for Ready-Mixed Concrete (incorporated by 
reference as specified in Sec.  250.198);
    (17) ASTM Standard C 150-07, approved May 1, 2007, Standard 
Specification for Portland Cement (incorporated by reference as 
specified in Sec.  250.198);

[[Page 22227]]

    (18) ASTM Standard C 330-05, approved December 15, 2005, Standard 
Specification for Lightweight Aggregates for Structural Concrete 
(incorporated by reference as specified in Sec.  250.198);
    (19) ASTM Standard C 595-08, approved January 1, 2008, Standard 
Specification for Blended Hydraulic Cements (incorporated by reference 
as specified in Sec.  250.198);
* * * * *
    (d) * * *

----------------------------------------------------------------------------------------------------------------
           Industry standard                                         Applicable to:
----------------------------------------------------------------------------------------------------------------
 
 
 
                                                  * * * * * * *
(1) ACI Standard 318-95, Building Code  Fixed and floating platform, as appropriate.
 Requirements for Reinforced Concrete
 (ACI 318-95) and Commentary (ACI 318R-
 95).
 
 
 
                                                  * * * * * * *
(7) ASTM Standard C 33-07, approved     ........................................................................
 December 15, 2007, Standard
 Specification for Concrete
 Aggregates;
(8) ASTM Standard C 94/C 94M-07,        ........................................................................
 approved January 1, 2007, Standard
 Specification for Ready-Mixed
 Concrete;
(9) ASTM Standard C 150-07, approved    ........................................................................
 May 1, 2007, Standard Specification
 for Portland Cement;
(10) ASTM Standard C 330-05, approved   ........................................................................
 December 15, 2005, Standard
 Specification for Lightweight
 Aggregates for Structural Concrete;
(11) ASTM Standard C 595-08, approved   ........................................................................
 January 1, 2008, Standard
 Specification for Blended Hydraulic
 Cements;
 
 
 
                                                  * * * * * * *
(16) ACI 357R-84, Guide for the Design  Fixed platforms
 and Construction of Fixed Offshore
 Concrete Structures, 1984; reapproved
 1997
 
 
 
                                                  * * * * * * *
----------------------------------------------------------------------------------------------------------------


0
6. Amend Sec.  250.1628 by revising paragraphs (b)(3) and (d)(4)(i) to 
read as follows:


Sec.  250.1628  Design, installation, and operation of production 
systems.

* * * * *
    (b) * * *
    (3) Electrical system information including a plan of each platform 
deck, outlining all hazardous areas classified according to API RP 500, 
Recommended Practice for Classification of Locations for Electrical 
Installations at Petroleum Facilities Classified as Class I, Division 1 
and Division 2, or API RP 505, Recommended Practice for Classification 
of Locations for Electrical Installations at Petroleum Facilities 
Classified as Class I, Zone 0, Zone 1, and Zone 2 (incorporated by 
reference as specified in Sec.  250.198), and outlining areas in which 
potential ignition sources are to be installed;
* * * * *
    (d) * * *
    (4) * * *
    (i) A plan of each platform deck, outlining all hazardous areas 
classified according to API RP 500, Recommended Practice for 
Classification of Locations for Electrical Installations at Petroleum 
Facilities Classified as Class I, Division 1 and Divisions 2, or API RP 
505, Recommended Practice for Classification of Locations for 
Electrical Installations at Petroleum Facilities Classified as Class I, 
Zone 0, Zone 1, and Zone 2 (incorporated by reference as specified in 
Sec.  250.198), and outlining areas in which potential ignition sources 
are to be installed;
* * * * *

0
7. Amend Sec.  250.1629 by:
0
A. Revising the last sentence of paragraph (b)(1) introductory text;
0
B. Revising paragraph (b)(3) introductory text; and
0
C. Revising the last sentence of paragraph (b)(4)(i).
    The revisoins read as follows:


Sec.  250.1629  Additional production and fuel gas system requirements.

* * * * *
    (b) * * *
    (1) * * * Pressure and fired vessels must have maintenance 
inspection, rating, repair, and alteration performed in accordance with 
the applicable provisions of API Pressure Vessel Inspections Code: In-
Service Inspection, Rating, Repair, and Alteration, API 510 (except 
Sections 5.8 and 9.5) (incorporated by reference as specified in Sec.  
250.198).
* * * * *
    (3) Firefighting systems. Firefighting systems must conform to 
subsection 5.2, Fire Water Systems, of API RP 14G, Recommended Practice 
for Fire Prevention and Control on Open Type Offshore Production 
Platforms (incorporated by reference as specified in Sec.  250.198), 
and must be subject to the approval of the District Manager. Additional 
requirements must apply as follows:
* * * * *
    (4) * * *
    (i) * * * A classified area is any area classified Class I, Group 
D, Division 1 or 2, following the guidelines of API RP 500 
(incorporated by reference as specified in Sec.  205.198), or any area 
classified Class I, Zone 0, Zone 1, or Zone 2, following the guidelines 
of API RP 505 (incorporated by reference as specified in Sec.  
205.198).
* * * * *
[FR Doc. 2010-9612 Filed 4-27-10; 8:45 am]
BILLING CODE 4310-MR-P