[Federal Register Volume 74, Number 173 (Wednesday, September 9, 2009)]
[Rules and Regulations]
[Pages 46334-46336]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: E9-20834]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2009-0515; Directorate Identifier 2008-NM-071-AD; 
Amendment 39-16007; AD 2009-18-11]
RIN 2120-AA64


Airworthiness Directives; Fokker Model F.28 Mark 0070 and 0100 
Series Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for the 
products listed above. This AD results from mandatory continuing 
airworthiness information (MCAI) originated by an aviation authority of 
another country to identify and correct an unsafe condition on an 
aviation product. The MCAI describes the unsafe condition as:

    Following a red illuminated ``DOOR NOT LOCKED'' status light 
indication on the door lock indication panel after lift off, the 
cabin crew operated the door lock handle. This resulted in 
inadvertent opening of the downward opening passenger door in 
flight. * * *
    After inspection, it was found that the false red light might be 
the result of an incorrect clearance between lever Part Number (P/N) 
A26997-003 and the Up-Limit Switch. If the Up-Limit Switch has an 
incorrect clearance, the combination with cabin differential 
pressure build-up after lift-off might result in a false steady 
illuminating red ``DOOR NOT LOCKED'' indication on the Door 
Indication Panel. * * *

* * * * *
The unsafe condition is inadvertent opening of the door lock handle in 
flight, which could result in rapid decompression of the airplane or 
ejection of a passenger or crewmember through the door. We are issuing 
this AD to require actions to correct the unsafe condition on these 
products.

DATES: This AD becomes effective October 14, 2009.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in this AD as of October 14, 
2009.

ADDRESSES: You may examine the AD docket on the Internet at http://www.regulations.gov or in person at the U.S. Department of 
Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 
227-1137; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 to include an AD that would apply to the specified products. 
That NPRM was published in the Federal Register on June 9, 2009 (74 FR 
27260). That NPRM proposed to correct an unsafe condition for the 
specified products. The MCAI states:

    Following a red illuminated ``DOOR NOT LOCKED'' status light 
indication on the door lock indication panel after lift off, the 
cabin crew operated the door lock handle. This resulted in 
inadvertent opening of the downward opening passenger door in 
flight. It appeared that the cabin crew was unaware of the content 
of Fokker 70/100 Service Letter (SL) 272. This SL informs not to 
operate the door lock handle after the aircraft has started to move 
or before it has come to a complete standstill.
    After inspection, it was found that the false red light might be 
the result of an incorrect clearance between lever Part Number (P/N) 
A26997-003 and the Up-Limit Switch. If the Up-Limit Switch has an 
incorrect clearance, the combination with cabin differential 
pressure build-up after lift-off might result in a false steady 
illuminating red ``DOOR NOT LOCKED'' indication on the Door 
Indication Panel. The original Fokker Service Bulletin SBF100-52-044 
and the associated Aircraft Maintenance Manual (AMM) task mentioned 
a clearance of 1,3 mm  0,3 mm. Later, based on a trial, 
an improved clearance of 0,3 mm  0,2 mm was introduced. 
Both documents have been revised for that reason. Later production 
serial number aircraft with downward opening passenger doors had the 
correct clearance introduced before delivery, but no action was 
taken to inspect and adjust the clearance on previously delivered or 
modified (per SBF100-52-044) serial numbers.
    Since an unsafe condition has been identified that is likely to 
exist or develop on other aircraft of the same type design, this 
[EASA] Airworthiness Directive (AD) requires two actions:

--The installation of a warning placard near the status lights of 
the door lock indication panel, instructing the cabin crew not to 
operate the door handle during flight and to inform the flight crew 
of the ``DOOR NOT LOCKED'' indication; and
--A one-time inspection of the clearance between lever P/N A26997-
003 and the Up-Limit Switch. If this clearance deviates from the 
limits given in AMM task 52-71-01-400-814-A, which is 0,3 mm  0,2 mm (0.0118 inch  0.0079 inch), corrective 
actions are required.

The unsafe condition is inadvertent opening of the door lock handle in 
flight, which could result in rapid decompression of the airplane or 
ejection of a passenger or crewmember through the door. The corrective 
action for improper clearance is adjusting the clearance between the 
lever and the up-limit switch. You may obtain further information by 
examining the MCAI in the AD docket.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM or on the determination of 
the cost to the public.

Conclusion

    We reviewed the available data and determined that air safety and 
the public interest require adopting the AD as proposed.

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.

[[Page 46335]]

    We might also have required different actions in this AD from those 
in the MCAI in order to follow our FAA policies. Any such differences 
are highlighted in a Note within the AD.

Costs of Compliance

    We estimate that this AD will affect 10 products of U.S. registry. 
We also estimate that it will take about 4 work-hours per product to 
comply with the basic requirements of this AD. The average labor rate 
is $80 per work-hour. Required parts will cost about $20 per product. 
Where the service information lists required parts costs that are 
covered under warranty, we have assumed that there will be no charge 
for these parts. As we do not control warranty coverage for affected 
parties, some parties may incur costs higher than estimated here. Based 
on these figures, we estimate the cost of this AD to the U.S. operators 
to be $3,400, or $340 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this AD and placed it in the AD docket.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains the NPRM, the regulatory evaluation, 
any comments received, and other information. The street address for 
the Docket Operations office (telephone (800) 647-5527) is in the 
ADDRESSES section. Comments will be available in the AD docket shortly 
after receipt.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new AD:

2009-18-11 Fokker Services B.V.: Amendment 39-16007. Docket No. FAA-
2009-0515; Directorate Identifier 2008-NM-071-AD.

Effective Date

    (a) This airworthiness directive (AD) becomes effective October 
14, 2009.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Fokker Model F.28 Mark 0070 and 0100 
series airplanes, certificated in any category, equipped with a 
downward-opening ``airstair'' type passenger door.

Subject

    (d) Air Transport Association (ATA) of America Codes 11 and 52: 
Placards and Markings, and Doors, respectively.

Reason

    (e) The mandatory continuing airworthiness information (MCAI) 
states:

    ``Following a red illuminated ``DOOR NOT LOCKED'' status light 
indication on the door lock indication panel after lift off, the 
cabin crew operated the door lock handle. This resulted in 
inadvertent opening of the downward opening passenger door in 
flight. It appeared that the cabin crew was unaware of the content 
of Fokker 70/100 Service Letter (SL) 272. This SL informs not to 
operate the door lock handle after the aircraft has started to move 
or before it has come to a complete standstill.
    ``After inspection, it was found that the false red light might 
be the result of an incorrect clearance between lever Part Number 
(P/N) A26997-003 and the Up-Limit Switch. If the Up-Limit Switch has 
an incorrect clearance, the combination with cabin differential 
pressure build-up after lift-off might result in a false steady 
illuminating red ``DOOR NOT LOCKED'' indication on the Door 
Indication Panel. The original Fokker Service Bulletin SBF100-52-044 
and the associated Aircraft Maintenance Manual (AMM) task mentioned 
a clearance of 1,3 mm  0,3 mm. Later, based on a trial, 
an improved clearance of 0,3 mm  0,2 mm was introduced. 
Both documents have been revised for that reason. Later production 
serial number aircraft with downward opening passenger doors had the 
correct clearance introduced before delivery, but no action was 
taken to inspect and adjust the clearance on previously delivered or 
modified (per SBF100-52-044) serial numbers.
    ``Since an unsafe condition has been identified that is likely 
to exist or develop on other aircraft of the same type design, this 
[EASA] Airworthiness Directive (AD) requires two actions:

--The installation of a warning placard near the status lights of 
the door lock indication panel, instructing the cabin crew not to 
operate the door handle during flight and to inform the flight crew 
of the ``DOOR NOT LOCKED'' indication; and
--A one-time inspection of the clearance between lever P/N A26997-
003 and the Up-Limit Switch. If this clearance deviates from the 
limits given in AMM task 52-71-01-400-814-A, which is 0,3 mm  0,2 mm (0.0118 inch  0.0079 inch), corrective 
actions are required.''

    The unsafe condition is inadvertent opening of the door lock 
handle in flight, which could result in rapid decompression of the 
airplane or ejection of a passenger or crewmember through the door. 
The corrective action for improper clearance is adjusting the 
clearance between the lever and the up-limit switch.

Actions and Compliance

    (f) Unless already done, do the following actions:
    (1) Within 500 flight cycles or 4 months after the effective 
date of this AD, whichever occurs first, install a new warning 
placard near the status lights of the panel of the door lock 
indication, in accordance with the Accomplishment Instructions of 
Fokker Service Bulletin SBF100-11-025, Revision 1, dated December 
13, 2007.
    (2) Within 4,000 flight cycles after the effective date of this 
AD, do a one-time

[[Page 46336]]

inspection of the clearance between lever P/N A26997-003 and the up-
limit switch, in accordance with the Accomplishment Instructions of 
Fokker Service Bulletin SBF100-52-086, dated November 1, 2007.
    (3) If any clearance is found outside the range defined in 
Fokker Service Bulletin SBF100-52-086, dated November 1, 2007, 
during the inspection required by paragraph (f)(2) of this AD, 
before further flight, correct the clearance in accordance with the 
Accomplishment Instructions of Fokker Service Bulletin SBF100-52-
086, dated November 1, 2007.
    (4) If done before the effective date of this AD, installing the 
warning placard near the status lights of the panel of the door lock 
indication, in accordance with Fokker Service Bulletin SBF100-11-
025, dated November 1, 2007, is acceptable for compliance with the 
requirements of paragraph (f)(1) of this AD.
    (5) Modifying the airplane in accordance with Fokker Service 
Bulletin SBF100-52-044, Revision 1, dated November 1, 2007, 
terminates the requirements of paragraph (f)(2) of this AD.

FAA AD Differences

    Note 1:  This AD differs from the MCAI and/or service 
information as follows:
    Note 1 of the ``Compliance'' section of European Aviation Safety 
Agency (EASA) Airworthiness Directive 2008-0020, dated January 28, 
2008, states that any airplane that has not yet been modified in 
accordance with Fokker Service Bulletin SBF100-52-069, dated 
December 3, 2001, must be modified prior to or concurrently with 
paragraph (f)(1) of this AD. However, all U.S. airplanes have met 
this requirement with the issuance of AD 2006-03-07, amendment 39-
14471; therefore, modification in accordance with Fokker Service 
Bulletin SBF100-52-069, dated December 3, 2001, is not applicable.

Other FAA AD Provisions

    (g) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. Send information to ATTN: Tom 
Rodriguez, Aerospace Engineer, International Branch, ANM-116, 
Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, 
Washington 98057-3356; telephone (425) 227-1137; fax (425) 227-1149. 
Before using any approved AMOC on any airplane to which the AMOC 
applies, notify your principal maintenance inspector (PMI) or 
principal avionics inspector (PAI), as appropriate, or lacking a 
principal inspector, your local Flight Standards District Office.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.
    (3) Reporting Requirements: For any reporting requirement in 
this AD, under the provisions of the Paperwork Reduction Act, the 
Office of Management and Budget (OMB) has approved the information 
collection requirements and has assigned OMB Control Number 2120-
0056.

Related Information

    (h) Refer to MCAI EASA Airworthiness Directive 2008-0020, dated 
January 28, 2008; Fokker Service Bulletin SBF100-11-025, Revision 1, 
dated December 13, 2007; and Fokker Service Bulletin SBF100-52-086, 
dated November 1, 2007; for related information.

Material Incorporated by Reference

    (i) You must use Fokker Service Bulletin SBF100-11-025, Revision 
1, dated December 13, 2007; and Fokker Service Bulletin SBF100-52-
086, dated November 1, 2007; as applicable; to do the actions 
required by this AD, unless the AD specifies otherwise. If you 
accomplish the optional modification specified in paragraph (f)(5) 
of this AD, you must use Fokker Service Bulletin SBF100-52-044, 
Revision 1, dated November 1, 2007, to perform that modification, 
unless the AD specifies otherwise.
    (1) The Director of the Federal Register approved the 
incorporation by reference of this service information under 5 
U.S.C. 552(a) and 1 CFR part 51.
    (2) For service information identified in this AD, contact 
Fokker Services B.V., Technical Services Dept., P.O. Box 231, 2150 
AE Nieuw-Vennep, the Netherlands; telephone +31 (0)252-627-350; fax 
+31 (0)252-627-211; e-mail 
[email protected]; Internet http://www.myfokkerfleet.com.
    (3) You may review copies of the service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, 
Washington. For information on the availability of this material at 
the FAA, call 425-227-1221 or 425-227-1152.
    (4) You may also review copies of the service information that 
is incorporated by reference at the National Archives and Records 
Administration (NARA). For information on the availability of this 
material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

    Issued in Renton, Washington, on August 18, 2009.
Stephen P. Boyd,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. E9-20834 Filed 9-8-09; 8:45 am]
BILLING CODE 4910-13-P