[Federal Register Volume 74, Number 30 (Tuesday, February 17, 2009)]
[Rules and Regulations]
[Pages 7310-7313]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: E9-3042]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2006-25730; Directorate Identifier 2006-NE-31-AD; 
Amendment 39-15798; AD 2009-02-08]
RIN 2120-AA64


Airworthiness Directives; Turbomeca Turmo IV A and IV C Series 
Turboshaft Engines

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: The FAA is superseding an existing airworthiness directive 
(AD) for Turbomeca Turmo IV A and IV C series turboshaft engines. That 
AD is applicable to engines with oil-tank-to-oil-cooler flexible 
lubrication pipes, part number (P/N) 0 249 92 813 0 or P/N 0 249 92 916 
0, installed. That AD currently requires identifying, inspecting, and 
replacing affected flexible lubrication pipes manufactured after April 
1, 2003. That AD also requires initial and repetitive borescope 
inspections of affected pipes, visual inspections for oil leakage, and 
visual inspections of the oil filter. That AD also requires that if 
both engines on the same helicopter each have an affected pipe, 
replacing one of the affected pipes before further flight. This AD does 
not contain that requirement. This AD requires the same inspections as 
the superseded AD and adds inspection of oil-pump-to-intermediate-
bearing flexible lubricating pipe, P/N 0 249 92 808 0. This AD also 
requires all remaining affected flexible lubrication pipes, P/N 0 249 
92 813 0, P/N 0 249 92 916 0, and P/N 0 249 92 808 to be replaced as 
terminating action to the repetitive inspections for those affected 
pipes. This AD results from additional shutdowns caused by pipes, P/N 0 
249 92 808 0, and the introduction of Turbomeca Modifications TU 231 
and TU 233 that replace pipes, P/N 0 249 92 813 0, P/N 0 249 92 916 0, 
and P/N 0 249 92 808. We are issuing this AD to prevent helicopter 
engine in-flight shutdown of one or both engines resulting in an 
emergency auto-rotation landing or accident.

DATES: Effective March 4, 2009. The Director of the Federal Register 
approved the incorporation by reference of certain publications listed 
in the regulations as of March 4, 2009.
    We must receive any comments on this AD by April 20, 2009.

ADDRESSES: Use one of the following addresses to comment on this AD.
     Federal eRulemaking Portal: Go to http://www.regulations.gov and follow the instructions for sending your 
comments electronically.
     Mail: Docket Management Facility, U.S. Department of 
Transportation, 1200 New Jersey Avenue, SE., West Building Ground 
Floor, Room W12-140, Washington, DC 20590-0001.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
     Fax: (202) 493-2251.

[[Page 7311]]


FOR FURTHER INFORMATION CONTACT: James Lawrence, Aerospace Engineer, 
Engine Certification Office, FAA, Engine and Propeller Directorate, 12 
New England Executive Park, Burlington, MA 01803; e-mail: 
[email protected]; telephone (781) 238-7176; fax (781) 238-7199.

SUPPLEMENTARY INFORMATION: On October 12, 2006, we issued AD 2006-21-
11, Amendment 39-14796 (71 FR 61642, October 19, 2006). That AD 
requires identifying and inspecting oil-tank-to-oil-cooler flexible 
lubrication pipes, P/N 0 249 92 813 0 or P/N 0 249 92 916 0, 
manufactured after April 1, 2003. If both engines on the same 
helicopter each have an affected pipe, then that AD requires replacing 
one of the affected pipes before further flight. That AD also requires 
initial and repetitive borescope inspections of affected pipes, visual 
inspections for oil leakage, and visual inspections of the oil filter, 
on engines that are not required to have an affected pipe replaced 
before further flight. That AD resulted from seven reports of oil 
leakage due to the deterioration of certain flexible lubrication pipes 
manufactured after April 1, 2003. That condition, if not corrected, 
could result in helicopter engine in-flight shutdown of one or both 
engines resulting in an emergency auto-rotation landing or accident.

Actions Since AD 2006-21-11 Was Issued

    Since AD 2006-21-11 was issued, the European Aviation Safety Agency 
(EASA), which is the Technical Agent for the Member States of the 
European Community, notified us that Turbomeca reported two additional 
occurrences of deterioration in a third P/N flexible lubrication pipe, 
P/N 0 249 92 808 0. EASA also notified us that Turbomeca issued 
mandatory service bulletins to add pipe P/N 0 249 92 808 0 to the list 
of affected pipes, to replace affected pipes, P/N 0 249 92 813 0 and P/
N 0 249 92 916 0 with a new P/N pipe, and to replace affected pipes, P/
N 0 249 92 808 0 with a new P/N pipe. This AD requires the same 
inspections as AD 2006-21-11 but requires replacing all remaining 
affected lubrication pipes, P/N 0 249 92 813 0 and P/N 0 249 92 916 0, 
with either a new P/N pipe or a pipe manufactured before April 1, 2003, 
as terminating action to the repetitive pipe inspections in this AD.

Relevant Service Information

    We have reviewed and approved the technical contents of Turbomeca 
Alert Mandatory Service Bulletin (MSB) No. A249 72 0802, Update No. 2, 
dated February 23, 2007. That Alert MSB describes procedures for 
identifying affected flexible lubrication pipes by their curing batch 
number, and describes procedures for performing repetitive borescope 
inspections of all other affected pipes and visual inspections of the 
oil filter. We have also reviewed and approved the technical contents 
of Turbomeca MSB No. 249 72 0231, Update No. 1, dated October 11, 2007. 
That MSB describes procedures for replacing remaining affected flexible 
lubrication pipes, P/N 0 249 92 813 0 and P/N 0 249 92 916 0, with 
pipes introduced by Modification TU 231. We have also reviewed and 
approved the technical contents of Turbomeca MSB No. 249 72 0233, dated 
September 1, 2008. That MSB describes procedures for replacing 
remaining affected flexible lubrication pipes, P/N 0 249 92 808 0, with 
pipes introduced by Modification TU 233. EASA classified these service 
bulletins as mandatory and issued AD 2008-0194 to ensure the 
airworthiness of these Turbomeca Turmo IV A and IV C series turboshaft 
engines in Europe.

Bilateral Airworthiness Agreement

    These engine models are manufactured in France and are type 
certificated for operation in the United States under the provisions of 
section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and 
the applicable bilateral airworthiness agreement. Under this bilateral 
airworthiness agreement, France has kept the FAA informed of the 
situation described above. We have examined the findings of EASA, 
reviewed all available information, and determined that AD action is 
necessary for products of this type design that are certificated for 
operation in the United States.

FAA's Determination and Requirements of This AD

    The unsafe condition described previously is likely to exist or 
develop on other Turbomeca Turmo IV A and IV C series turboshaft 
engines of the same type design. We are issuing this AD to prevent 
engine in-flight shutdown of one or both helicopter engines resulting 
in an emergency auto-rotation landing or accident. This AD requires:
     Identifying and inspecting certain flexible lubrication 
pipes manufactured after April 1, 2003; and
     Initial and repetitive borescope inspections of affected 
pipes, visual inspections for oil leakage, and visual inspections of 
the oil filter, on engines that are not required to have an affected 
pipe replaced before further flight; and
     Replacing all remaining affected lubrication pipes, P/N 0 
249 92 813 0 and P/N 0 249 92 916 0, and all remaining affected 
lubrication pipes, P/N 0 249 92 808 0, with new P/N pipes or pipes 
manufactured before April 1, 2003, within 45 days or 50 operating hours 
after the effective date of the AD, whichever occurs first, as 
terminating action to the repetitive pipe inspections in this AD.

FAA's Determination of the Effective Date

    Since an unsafe condition exists that requires the immediate 
adoption of this AD, we have found that notice and opportunity for 
public comment before issuing this AD are impracticable, and that good 
cause exists for making this amendment effective in less than 30 days.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety and was not preceded by notice and an opportunity for public 
comment; however, we invite you to send us any written relevant data, 
views, or arguments regarding this AD. Send your comments to an address 
listed under ADDRESSES. Include ``Docket No. FAA-2006-25730; 
Directorate Identifier 2006-NE-31-AD'' in the subject line of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of the rule that might 
suggest a need to modify it.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact 
with FAA personnel concerning this proposed AD. Using the search 
function of the Web site, anyone can find and read the comments in any 
of our dockets, including, if provided, the name of the individual who 
sent the comment (or signed the comment on behalf of an association, 
business, labor union, etc.). You may review the DOT's complete Privacy 
Act Statement in the Federal Register published on April 11, 2000 (65 
FR 19477-78).

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this AD, the regulatory evaluation, 
any comments received, and other information. The street address for 
the Docket Operations office (telephone (800) 647-5527) is the same as 
the Mail

[[Page 7312]]

address provided in the ADDRESSES section. Comments will be available 
in the AD docket shortly after receipt.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We have determined that this AD will not have federalism 
implications under Executive Order 13132. This AD will not have a 
substantial direct effect on the States, on the relationship between 
the national Government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a summary of the costs to comply with this AD and 
placed it in the AD Docket. You may get a copy of this summary at the 
address listed under ADDRESSES.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Safety.

Adoption of the Amendment

0
Under the authority delegated to me by the Administrator, the Federal 
Aviation Administration amends part 39 of the Federal Aviation 
Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by removing Amendment 39-14796 (71 FR 
61642, October 19, 2006), and by adding a new airworthiness directive, 
Amendment 39-15798, to read as follows:

2009-02-08 Turbomeca: Amendment 39-15798. Docket No. FAA-2006-25730; 
Directorate Identifier 2006-NE-31-AD.

Effective Date

    (a) This airworthiness directive (AD) becomes effective March 4, 
2009.

Affected ADs

    (b) This AD supersedes AD 2006-21-11, Amendment 39-14796.

Applicability

    (c) This AD applies to Turbomeca Turmo IV A and IV C series 
turboshaft engines with oil-tank-to-oil-cooler flexible lubrication 
pipes, part number (P/N) 0 249 92 813 0, or P/N 0 249 92 916 0, or 
oil-pump-to-intermediate-bearing flexible lubrication pipes, P/N 0 
249 92 808 0 installed. These engines are installed on, but not 
limited to, Eurocopter SA 330F, G, or J PUMA helicopters.

Unsafe Condition

    (d) This AD results from:
    (1) Additional shutdowns caused by flexible oil-pump-to-
intermediate-bearing-lubrication pipes, P/N 0 249 92 808 0; and
    (2) The introduction of a new P/N pipe through Turbomeca 
Modification TU 231, as a replacement for affected oil-tank-to-oil-
cooler flexible lubrication pipes, P/N 0 249 92 813 0 and P/N 0 249 
92 916 0; and
    (3) The introduction of a new P/N pipe through Turbomeca 
Modification TU 233, as a replacement for affected oil-pump-to-
intermediate-bearing flexible lubrication pipes, P/N 0 249 92 808 0.
    (4) We are issuing this AD to prevent helicopter engine in-
flight shutdown of one or both engines resulting in an emergency 
auto-rotation landing or accident.

Compliance

    (e) You are responsible for having the actions required by this 
AD performed within the compliance times specified unless the 
actions have already been done.

Initial Actions

    (f) Before further flight:
    (1) Identify the curing batch of the flexible lubricating pipes 
listed in paragraph (c) of this AD.
    (2) For oil-tank-to-oil-cooler flexible lubrication pipes, P/N 0 
249 92 813 0 and P/N 0 249 92 916 0, and for oil-pump-to-
intermediate-bearing flexible lubrication pipes, P/N 0 249 92 808 0, 
with a curing batch of ``2T03'' (meaning 2nd quarter of 2003), or 
subsequent batch:
    (i) Borescope-inspect the pipe for deterioration, visually 
inspect for oil leakage, and visually inspect the oil filter for 
black particle deterioration from the pipe.
    (ii) Replace the pipe with a serviceable pipe, if deterioration 
or leakage is found.

Repetitive Actions

    (g) Within an additional 25 operating hours, on engines still 
having an affected flexible lubrication pipe, P/N 0 249 92 813 0, P/
N 0 249 92 916 0, or P/N 0 249 92 808 0 installed:
    (1) Borescope-inspect the pipe for deterioration, visually 
inspect the pipe for oil leakage, and visually inspect the oil 
filter for black particle deterioration from the pipe.
    (2) Replace pipes with serviceable pipes, if deterioration or 
leakage is found.

Terminating Action for Affected Flexible Lubricating Pipes

    (h) Within 45 days or 50 operating hours after the effective 
date of this AD, whichever occurs first, as terminating action to 
the repetitive inspections required by this AD:
    (1) Replace oil-tank-to-oil-cooler flexible lubrication pipes, 
P/N 0 249 92 813 0 and P/N 0 249 92 916 0 that have a curing batch 
of ``2T03'' or later, with a serviceable pipe.
    (2) Replace oil-pump-to-intermediate-bearing flexible 
lubrication pipes, P/N 0 249 92 808 0 that have a curing batch of 
``2T03'' or later, with a serviceable pipe.

Definitions

    (i) For the purposes of this AD, a serviceable oil-tank-to-oil-
cooler flexible lubrication pipe is one with a curing batch before 
April 1, 2003 (before ``2T03''), or one incorporating Modification 
TU 231. Information about Modification TU 231 can be found in 
Turbomeca Mandatory Service Bulletin (MSB) No. 249 72 0231.
    (j) For the purposes of this AD, a serviceable oil-pump-to-
intermediate-bearing flexible lubrication pipe is one with a curing 
batch before ``2T03'' or one incorporating Modification TU 233. 
Information about Modification TU 233 can be found in Turbomeca MSB 
No. 249 72 0233.

Alternative Methods of Compliance

    (k) The Manager, Engine Certification Office, has the authority 
to approve alternative methods of compliance for this AD if 
requested using the procedures found in 14 CFR 39.19.

Related Information

    (l) Information on performing the initial and repetitive actions 
in this AD can be found in Turbomeca Alert Mandatory Service 
Bulletin (MSB) No. A249 72 0802.
    (m) Contact Turbomeca S.A., 40220 Tarnos, France; e-mail: [email protected]; telephone 33 05 59 74 40 00, fax 33 05 59 74 
45 15, or go to: http://www.turbomeca-support.com, for a copy of the 
service information identified in this AD.
    (n) European Aviation Safety Agency AD 2008-0194, dated October 
31, 2008, also addresses the subject of this AD.

[[Page 7313]]

    (o) Contact James Lawrence, Aerospace Engineer, Engine 
Certification Office, FAA, Engine and Propeller Directorate, 12 New 
England Executive Park, Burlington, MA 01803; e-mail: 
[email protected]; telephone (781) 238-7176, fax (781) 238-
7199, for more information about this AD.

    Issued in Burlington, Massachusetts, on January 14, 2009.
Peter A. White,
Assistant Manager, Engine and Propeller Directorate, Aircraft 
Certification Service.
[FR Doc. E9-3042 Filed 2-13-09; 8:45 am]
BILLING CODE 4910-13-P