[Federal Register Volume 73, Number 221 (Friday, November 14, 2008)]
[Rules and Regulations]
[Pages 67363-67368]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: E8-26911]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2008-1200; Directorate Identifier 2008-NM-178-AD; 
Amendment 39-15737; AD 2008-23-16]
RIN 2120-AA64


Airworthiness Directives; Bombardier Model CL-600-2B19 (Regional 
Jet Series 100 & 440) Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: The FAA is superseding an existing airworthiness directive 
(AD) that applies to certain Bombardier Model CL-600-2B19 (Regional Jet 
Series 100 & 440) airplanes. The existing AD currently requires 
inspecting to identify the wing anti-ice ducts (piccolo tubes) in the 
wing leading edge. For airplanes with affected piccolo tubes, the 
existing AD requires revising the airplane flight manual (AFM) to 
introduce new procedures for operation in icing conditions. The 
existing AD provides an optional implementation of repetitive 
inspections for cracks of affected piccolo tubes, and corrective 
actions if necessary, which terminates the operational limitations. The 
existing AD also provides an optional installation of certain new 
piccolo tubes, which terminates both the AFM revision and the 
inspections. This AD adds airplanes to the applicability, requires 
revising the AFM to introduce new procedures for operation in icing 
conditions, and requires inspecting to determine if certain anti-ice 
piccolo ducts are installed, and replacing or repairing the piccolo 
duct if necessary. This AD also provides an optional terminating action 
of replacing all affected piccolo ducts. This AD results from reports 
of failed piccolo tubes. We are issuing this AD to prevent cracked 
piccolo tubes, which could result in air leakage, a possible adverse 
effect on the anti-ice air distribution pattern and anti-ice capability 
without annunciation to

[[Page 67364]]

the flight crew, and consequent reduced controllability of the 
airplane.

DATES: This AD becomes effective December 1, 2008.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in the AD as of December 1, 
2008.
    On September 7, 2005 (70 FR 49164, August 23, 2005), the Director 
of the Federal Register approved the incorporation by reference of 
certain other publications listed in the AD.
    We must receive any comments on this AD by December 15, 2008.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.
    For service information identified in this AD, contact Bombardier, 
Inc., Canadair, Aerospace Group, P.O. Box 6087, Station Centre-ville, 
Montreal, Quebec H3C 3G9, Canada; telephone 514-855-8500; fax 514-855-
8501; E-mail [email protected]; Internet http://www.bombardier.com.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this AD, the regulatory evaluation, 
any comments received, and other information. The street address for 
the Docket Office (telephone 800-647-5527) is in the ADDRESSES section. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Fabio Buttitta, Aerospace Engineer, 
New York Aircraft Certification Office, ANE-171, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New 
York 11590; telephone (516) 228-7303; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Discussion

    On August 11, 2005, the FAA issued AD 2005-17-12, amendment 39-
14223 (70 FR 49164, August 23, 2005). That AD applies to certain 
Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. 
That AD requires inspecting to identify the wing anti-ice ducts 
(piccolo tubes) in the wing leading edge. For airplanes with affected 
piccolo tubes, that AD requires revising the airplane flight manual 
(AFM) to introduce new procedures for operation in icing conditions. 
That AD provides an optional implementation of repetitive inspections 
for cracks of affected piccolo tubes, and corrective actions if 
necessary, which terminates the operational limitations. That AD also 
provides an optional installation of certain new piccolo tubes, which 
terminates both the AFM revision and the inspections. That AD resulted 
from reports of failed piccolo tubes. The actions specified in that AD 
are intended to prevent cracked piccolo tubes, which could result in 
air leakage, a possible adverse effect on the anti-ice air distribution 
pattern and anti-ice capability without annunciation to the flight 
crew, and consequent reduced controllability of the airplane.

Actions Since AD Was Issued

    Since we issued AD 2005-17-12, we received a report that faulty 
piccolo tubes might have been installed in a number of leading edge 
assemblies built as spares, and whose current locations are not 
specifically known. These faulty parts may have been installed on 
airplanes affected by that AD. Faulty piccolo tubes could crack, which 
could result in air leakage, a possible adverse effect on the anti-ice 
air distribution pattern and anti-ice capability without annunciation 
to the flight crew, and consequent reduced controllability of the 
airplane.

Relevant Service Information

    Bombardier has issued Canadair Temporary Revision RJ/155-6, dated 
September 17, 2008 (``the TR''), to the Canadair Regional Jet AFM, CSP 
A-012. The TR describes new procedures for operation in icing 
conditions and supersedes Canadair TR RJ/155, dated July 5, 2005 (which 
we referred to as the appropriate source of service information for 
doing the AFM revision required by AD 2005-17-12).
    Bombardier has also issued Service Bulletin 601R-30-029, Revision 
B, dated August 29, 2005. We referred to Bombardier Service Bulletin 
601R-30-029, Revision A, dated July 7, 2005, as the appropriate source 
of service information for doing certain actions required by AD 2005-
17-12. Revision B contains the same procedures as Revision A but adds 
airplanes to the effectivity and removes certain other airplanes from 
the effectivity.
    Bombardier has also issued Alert Service Bulletin A601R-30-032, 
dated September 18, 2008. This service bulletin supersedes Bombardier 
Service Bulletin 601R-30-029, Revision A, dated July 7, 2005. 
Bombardier Alert Service Bulletin A601R-30-032 describes procedures for 
inspecting to determine if certain anti-ice piccolo ducts are 
installed, and replacing or repairing the piccolo duct if necessary.
    Accomplishing the actions specified in the service information is 
intended to adequately address the unsafe condition. Transport Canada 
Civil Aviation (TCCA) mandated the service information and issued 
Canadian airworthiness directive CF-2008-30, dated October 7, 2008 
(referred to after this as ``the MCAI''), to ensure the continued 
airworthiness of these airplanes in Canada. Canadian airworthiness 
directive CF-2008-30 supersedes Canadian airworthiness directive CF-
2005-26R1, dated September 21, 2005, and adds airplanes to the 
applicability. We referred to Canadian airworthiness directive CF-2005-
26, dated July 11, 2005, in our AD 2005-17-12.

FAA's Determination and Requirements of This AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are issuing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.
    Therefore, we are issuing this AD to supersede AD 2005-17-12. This 
new AD retains certain requirements of the existing AD. This AD also 
requires accomplishing the actions specified in the service information 
described previously, except as discussed under ``Differences Between 
the AD and the Service Information.'' This AD also adds airplanes to 
the applicability and removes certain other airplanes from the 
applicability.

Differences Between the AD and the Service Information

    Where Bombardier Alert Service Bulletin A601R-30-032, dated 
September 18, 2008, specifies that Bombardier may be contacted for 
information regarding repair, this AD

[[Page 67365]]

requires repair according to a method approved by either the Manager, 
New York ACO, or TCCA (or its delegated agent).

Interim Action

    We consider this AD interim action. We are currently considering 
requiring the replacement of all piccolo ducts that have serial numbers 
identified in Part A, Paragraph 2.A., of the Accomplishment 
Instructions of Bombardier Alert Service Bulletin A601R-30-032, dated 
September 18, 2008, with piccolo ducts that do not have the affected 
serial numbers, which will constitute terminating action for the 
actions required by this AD. However, the planned compliance time for 
the replacement would allow enough time to provide notice and 
opportunity for prior public comment on the merits of the replacement.

FAA's Justification and Determination of the Effective Date

    Because of our requirement to promote safe flight of civil aircraft 
and thus, the critical need to ensure proper functioning of the anti-
ice systems during the upcoming winter season, and the short compliance 
time involved with this action, this AD must be issued immediately.
    Because an unsafe condition exists that requires the immediate 
adoption of this AD, we find that notice and opportunity for prior 
public comment hereon are impracticable and that good cause exists for 
making this amendment effective in less than 30 days.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety, and we did not provide you with notice and an opportunity to 
provide your comments before it becomes effective. However, we invite 
you to send any written data, views, or arguments about this AD. Send 
your comments to an address listed under the ADDRESSES section. Include 
``Docket No. FAA-2008-1200; Directorate Identifier 2008-NM-178-AD'' at 
the beginning of your comments. We specifically invite comments on the 
overall regulatory, economic, environmental, and energy aspects of this 
AD. We will consider all comments received by the closing date and may 
amend this AD because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We have determined that this AD will not have federalism 
implications under Executive Order 13132. This AD will not have a 
substantial direct effect on the States, on the relationship between 
the national government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that the regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this AD and placed it in the AD docket. See the ADDRESSES 
section for a location to examine the regulatory evaluation.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the FAA amends part 39 of the Federal Aviation Regulations (14 CFR part 
39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The Federal Aviation Administration (FAA) amends Sec.  39.13 by 
removing amendment 39-14223 (70 FR 49164, August 23, 2005) and adding 
the following new AD:

2008-23-16 Bombardier, Inc. (Formerly Canadair): Docket No. FAA-
2008-1200; Directorate Identifier 2008-NM-178-AD; Amendment 39-
15737.

Effective Date

    (a) This AD becomes effective December 1, 2008.

Affected ADs

    (b) This AD supersedes AD 2005-17-12.

Applicability

    (c) This AD applies to Bombardier Model CL-600-2B19 (Regional 
Jet Series 100 & 440) airplanes, certificated in any category; 
serial numbers (S/Ns) 7003 through 7067 inclusive, 7069 through 7990 
inclusive, 8000 through 8076 inclusive, 8082, 8086, 8090 through 
8092 inclusive, 8096, and 8097.

Unsafe Condition

    (d) This AD results from reports of failed piccolo tubes. We are 
issuing this AD to prevent cracked piccolo tubes, which could result 
in air leakage, a possible adverse effect on the anti-ice air 
distribution pattern and anti-ice capability without annunciation to 
the flight crew, and consequent reduced controllability of the 
airplane.

Compliance

    (e) You are responsible for having the actions required by this 
AD performed within the compliance times specified, unless the 
actions have already been done.

Restatement of Requirements of AD 2005-17-12

Identification of Affected Piccolo Tubes

    (f) For airplanes having S/Ns 7013, 7017, 7037, 7046, 7059, 
7076, 7105, 7127, 7151, 7157, 7163, 7174, 7179, 7203, 7204, 7228, 
7271, 7347, 7362, 7378, 7417 through 7990 inclusive, 8000 through 
8076 inclusive, 8082, 8086, 8090 through 8092 inclusive, 8096 and 
8097: Before the airplane accumulates 3,000 total flight hours, or 
within 14 days after September 7, 2005 (the effective date of AD 
2005-17-12), whichever occurs later, determine whether any affected 
piccolo tube is installed on the airplane. Affected piccolo tubes 
are identified in paragraph 1.A. of Bombardier Service Bulletin 
601R-30-029, Revision A, dated July 7, 2005. Doing the action 
required by paragraph (p), (q), (r), or (w) of this AD terminates 
the requirements of this paragraph.

Revision to Airplane Flight Manual (AFM)

    (g) For airplanes with an affected or unidentifiable piccolo 
tube found during the

[[Page 67366]]

action required by paragraph (f) of this AD: Before the airplane 
accumulates 3,000 total flight hours, or within 14 days after 
September 7, 2005, whichever occurs later, revise the Operating 
Limitations and Abnormal Procedures sections of the Canadair 
Regional Jet AFM, CSP A-012, to include the information in Canadair 
Temporary Revision (TR) RJ/155, dated July 5, 2005, as specified in 
the TR. This may be done by inserting a copy of the TR into the AFM. 
This TR introduces new procedures for operation in icing conditions. 
Operate the airplane according to the limitations and procedures in 
the TR except as required by paragraph (n) of this AD. When this TR 
has been included in general revisions of the AFM, the general 
revisions may be inserted in the AFM, provided the relevant 
information in the general revision is identical to that in the TR. 
After the AFM revision required by paragraph (n) of this AD has been 
done, remove the AFM limitation specified in this paragraph.

Optional Inspections

    (h) For airplanes with an affected or unidentifiable piccolo 
tube found during the action required by paragraph (f) of this AD: 
The operating limitations and abnormal procedures specified in 
Canadair TR RJ/155, dated July 5, 2005, as required by paragraph (g) 
of this AD, may be removed from the AFM, provided all requirements 
of this paragraph have been satisfied.
    (1) A fluorescent dye penetrant inspection for cracks of the 
piccolo tubes is done and repeated thereafter within 2,000-flight-
hour intervals in accordance with the Accomplishment Instructions of 
Bombardier Service Bulletin 601R-30-029, Revision A, dated July 7, 
2005. An inspection done before September 7, 2005, in accordance 
with Bombardier Service Bulletin 601R-30-029, dated June 17, 2005, 
is acceptable for compliance with the requirements of paragraph 
(h)(1) of this AD. Doing the inspection required by paragraph (u) of 
this AD terminates the actions required by this paragraph.
    (2) All applicable corrective actions are done as specified in 
paragraph (j) of this AD.

AFM Limitations Required for Exceeding Inspection Interval

    (i) For airplanes having S/Ns 7013, 7017, 7037, 7046, 7059, 
7076, 7105, 7127, 7151, 7157, 7163, 7174, 7179, 7203, 7204, 7228, 
7271, 7347, 7362, 7378, 7417 through 7990 inclusive, 8000 through 
8076 inclusive, 8082, 8086, 8090 through 8092 inclusive, 8096 and 
8097: During any period in which the inspection interval exceeds 
2,000 flight hours after the initial inspection specified in 
paragraph (h)(1) of this AD, the airplane must be operated under the 
limitations and abnormal procedures specified in paragraph (g) of 
this AD. Doing the action required by paragraph (p), (q), (r), or 
(w) of this AD terminates the requirements of this paragraph.

Corrective Action

    (j) If any crack is found during any inspection required by 
paragraph (h) of this AD: Before further flight, do the actions 
specified in paragraph (j)(1), (j)(2), (j)(3), (j)(4), or (j)(5) of 
this AD, except as required by paragraph (k) of this AD.
    (1) Replace the cracked piccolo tube, in accordance with the 
Accomplishment Instructions of Bombardier Service Bulletin 601R-30-
029, Revision A, dated July 7, 2005, with a new piccolo tube that 
has the same part number as identified in paragraph 1.A. of 
Bombardier Service Bulletin 601R-30-029, Revision A, dated July 7, 
2005, but that does not have a serial number listed in that 
paragraph.
    (2) Replace the cracked piccolo tube, in accordance with the 
Accomplishment Instructions of Bombardier Service Bulletin 601R-30-
029, Revision A, dated July 7, 2005, with a new piccolo tube that 
has a part number identified in the applicable Bombardier 
illustrated parts catalog but not identified in paragraph 1.A. of 
Bombardier Service Bulletin 601R-30-029, Revision A, dated July 7, 
2005, or with a new piccolo tube identified in paragraph (l) of this 
AD.
    (3) Replace the cracked piccolo tube, in accordance with the 
Accomplishment Instructions of Bombardier Service Bulletin 601R-30-
029, Revision A, dated July 7, 2005, with a piccolo tube that has 
been inspected in accordance with the Accomplishment Instructions of 
Bombardier Service Bulletin 601R-30-029, Revision A, dated July 7, 
2005, is not cracked, and has not accumulated any air time (hours' 
time-in-service) since inspection.
    (4) Replace the cracked piccolo tube with a piccolo tube that 
has been repaired in accordance with a method approved by either the 
Manager, New York Aircraft Certification Office (ACO), ANE-172, FAA; 
or Transport Canada Civil Aviation (TCCA) (or its delegated agent); 
and has not accumulated any air time (hours time-in-service) since 
the repair.
    (5) Reinstall the cracked piccolo tube and operate the airplane 
in accordance with a method approved by either the Manager, New York 
ACO, or TCCA (or its delegated agent). Operation in accordance with 
the provisions of Master Minimum Equipment List (MMEL) entry 30-12-
03 is acceptable for compliance with the requirements of this 
paragraph.

Exception to Service Bulletin Procedures

    (k) Where Bombardier Service Bulletin 601R-30-029, Revision A, 
dated July 7, 2005, specifies that Bombardier may be contacted for 
information regarding repair, this AD requires repair according to a 
method approved by either the Manager, New York ACO, or TCCA (or its 
delegated agent).

Optional Terminating Action for Paragraphs (f), (g), (h), (i), and (j)

    (l) For airplanes having S/Ns 7013, 7017, 7037, 7046, 7059, 
7076, 7105, 7127, 7151, 7157, 7163, 7174, 7179, 7203, 7204, 7228, 
7271, 7347, 7362, 7378, 7417 through 7990 inclusive, 8000 through 
8076 inclusive, 8082, 8086, 8090 through 8092 inclusive, 8096 and 
8097: Installation, in accordance with the Accomplishment 
Instructions of Bombardier Service Bulletin 601R-30-029, Revision A, 
dated July 7, 2005, of a complete set of new inboard, center, and 
outboard piccolo tubes, as identified in paragraphs (l)(1), (l)(2), 
and (l)(3) of this AD terminates the requirements of paragraphs (f), 
(g), (h), (i), and (j) of this AD. When these piccolo tubes have 
been installed, remove the Operating Limitations and Abnormal 
Procedures, if inserted in accordance with paragraph (g) of this AD, 
from the AFM.
    (1) For the inboard piccolo tube: P/N 601-80032-7 (14432-107) 
and 601-80032-8 (14432-108).
    (2) For the center piccolo tube: P/N 14464-105 and 14464-106.
    (3) For the outboard piccolo tube: P/N 14463-109 and 14463-110.

Parts Installation

    (m) For airplanes having S/Ns 7013, 7017, 7037, 7046, 7059, 
7076, 7105, 7127, 7151, 7157, 7163, 7174, 7179, 7203, 7204, 7228, 
7271, 7347, 7362, 7378, 7417 through 7990 inclusive, 8000 through 
8076 inclusive, 8082, 8086, 8090 through 8092 inclusive, 8096 and 
8097: As of September 7, 2005, no person may install, on any 
airplane, a piccolo tube having a P/N listed in paragraph 1.A. of 
Bombardier Service Bulletin 601R-30-029, Revision A, dated July 7, 
2005, unless the applicable requirements of paragraphs (f) through 
(l) of this AD have been accomplished for that piccolo tube before 
the effective date of this AD or the requirements specified in 
paragraph (v) of this AD have been accomplished. As of the effective 
date of this AD, the requirements of paragraph (v) of this AD must 
be followed.

New Requirements of This AD

New Revision to AFM

    (n) For all airplanes: Within 14 days after the effective date 
of this AD, revise the Operating Limitations and Abnormal Procedures 
sections of the Canadair Regional Jet AFM, CSP A-012, to include the 
information in Canadair (Bombardier) TR RJ/155-6, dated September 
17, 2008, as specified in that TR. This may be done by inserting a 
copy of Canadair (Bombardier) TR RJ/155-6 into the AFM. This TR 
introduces new procedures for operation in icing conditions. After 
the AFM revision specified in this paragraph has been done, the AFM 
limitation required by paragraph (g) of this AD must be removed from 
the AFM.

    Note 1: When Canadair (Bombardier) TR RJ/155-6, dated September 
17, 2008, has been included in general revisions of the AFM, the 
general revisions may be inserted in the AFM, provided the relevant 
information in the general revision is identical to that in Canadair 
(Bombardier) TR RJ/155-6.

    (o) Before further flight after accomplishing paragraph (n) of 
this AD, operate the airplane according to the limitations and 
procedures in Canadair (Bombardier) TR RJ/155-6, dated September 17, 
2008, except that MMEL entry 30-12-03, which permits the wing anti-
ice system to be inoperative with specific provisions, is not 
affected by this AD.

Records Check

    (p) For airplanes having S/Ns 7003 through 7013 inclusive, 7015, 
7016, 7018 through 7036 inclusive, 7038 through 7045 inclusive, 7047 
through 7058 inclusive, 7060 through 7067 inclusive, 7069 through 
7075 inclusive,

[[Page 67367]]

7077 through 7104 inclusive, 7106 through 7126 inclusive, 7128 
through 7150 inclusive, 7152 through 7156 inclusive, 7158 through 
7162 inclusive, 7164 through 7178 inclusive, 7180 through 7202 
inclusive, 7204 through 7227 inclusive, 7229 through 7270 inclusive, 
7272 through 7346 inclusive, 7348 through 7358 inclusive, 7360, 
7361, 7363 through 7377 inclusive, 7379, 7380, 7382 through 7416 
inclusive, 8056 through 8076 inclusive, 8082, 8086, 8090 though 8092 
inclusive, 8096 and 8097: Within 30 days after the effective date of 
this AD, review the airplane maintenance records to determine if any 
anti-ice piccolo ducts or complete leading edge sections have been 
replaced since May 1, 2000. Doing the review in this paragraph 
terminates the requirements of paragraphs (f) and (i) of this AD. 
Doing the action specified in paragraph (w) of this AD terminates 
the requirements of this paragraph.
    (1) If no anti-ice piccolo ducts and no complete leading edge 
sections have been replaced since May 1, 2000, no further action is 
required by this paragraph.
    (2) If any anti-ice piccolo duct or complete leading edge 
section has been replaced since May 1, 2000, or if it cannot be 
conclusively determined that no anti-ice piccolo ducts and no 
complete leading edge sections have been replaced since May 1, 2000, 
before further flight, inspect the serial numbers of the replaced 
ducts. A review of airplane maintenance records is acceptable in 
lieu of this inspection if the serial number of the duct can be 
conclusively determined from that review.
    (i) If none of the piccolo duct serial numbers matches any of 
those in Part A, Paragraph 2.A., of the Accomplishment Instructions 
of Bombardier Alert Service Bulletin A601R-30-032, dated September 
18, 2008, no further action is required by this paragraph.
    (ii) If any of the piccolo duct serial numbers matches any of 
those in Part A, Paragraph 2.A., of the Accomplishment Instructions 
of Bombardier Alert Service Bulletin A601R-30-032, dated September 
18, 2008, or if the serial number cannot be determined, do the 
actions required by paragraph (s) of this AD.
    (q) For airplanes having S/Ns 7014, 7017, 7037, 7046, 7059, 
7076, 7105, 7127, 7151, 7157, 7163, 7179, 7203, 7228, 7271, 7347, 
7359, 7362, 7378, 7381, 7417 through 7990 inclusive, and 8000 
through 8055 inclusive, on which Bombardier Service Bulletin 601R-
30-029 has been accomplished: Within 30 days after the effective 
date of this AD, review the airplane maintenance records to 
determine if any anti-ice piccolo ducts or complete leading edge 
sections have been replaced since accomplishing Bombardier Service 
Bulletin 601R-30-029. Doing the action in this paragraph terminates 
the requirements of paragraphs (f) and (i) of this AD. Doing the 
action specified in paragraph (w) of this AD terminates the 
requirements of this paragraph.
    (1) If no anti-ice piccolo ducts and no complete leading edge 
sections have been replaced since May 1, 2000, no further action is 
required by this paragraph.
    (2) If any anti-ice piccolo duct or complete leading edge 
section has been replaced since May 1, 2000, or if it cannot be 
conclusively determined that no anti-ice piccolo ducts and no 
complete leading edge sections have been replaced since May 1, 2000, 
before further flight, inspect the serial numbers of the replaced 
ducts. A review of airplane maintenance records is acceptable in 
lieu of this inspection if the serial number of the duct can be 
conclusively determined from that review.
    (i) If none of the piccolo duct serial numbers matches any of 
those in Part A, Paragraph 2.A., of the Accomplishment Instructions 
of Bombardier Alert Service Bulletin A601R-30-032, dated September 
18, 2008, no further action is required by this paragraph.
    (ii) If any of the piccolo duct serial numbers matches any of 
those in Part A, Paragraph 2.A., of the Accomplishment Instructions 
of Bombardier Alert Service Bulletin A601R-30-032, dated September 
18, 2008, or if the serial number cannot be determined, do the 
actions required by paragraph (s) of this AD.
    (r) For airplanes having S/Ns 7014, 7017, 7037, 7046, 7059, 
7076, 7105, 7127, 7151, 7157, 7163, 7179, 7203, 7228, 7271, 7347, 
7359, 7362, 7378, 7381, 7417 through 7990 inclusive, and 8000 
through 8055 inclusive, on which Bombardier Service Bulletin 601R-
30-029 has not been accomplished: Within 30 days after the effective 
date of this AD, inspect the serial numbers of the piccolo ducts. A 
review of airplane maintenance records is acceptable in lieu of this 
inspection if the serial number of the duct can be conclusively 
determined from that review. Doing the inspection in this paragraph 
terminates the requirements of paragraphs (f) and (i) of this AD. 
Doing the action specified in paragraph (w) of this AD terminates 
the requirements of this paragraph.
    (1) If none of the piccolo duct serial numbers matches any of 
those in Part A, Paragraph 2.A., of the Accomplishment Instructions 
of Bombardier Alert Service Bulletin A601R-30-032, dated September 
18, 2008, no further action is required by this paragraph.
    (2) If any of the piccolo duct serial numbers matches any of 
those in Part A, Paragraph 2.A., of the Accomplishment Instructions 
of Bombardier Alert Service Bulletin A601R-30-032, dated September 
18, 2008, or if the serial number cannot be determined, do the 
actions required by paragraph (s) of this AD.

Inspection of the Wing Anti-Ice Piccolo Ducts

    (s) For airplanes having a piccolo duct identified in paragraph 
(p)(2)(ii), (q)(2)(ii), or (r)(2) of this AD: Within 30 days after 
doing the action specified in paragraph (p), (q), or (r) of this AD, 
as applicable, do a fluorescent dye penetrant inspection for 
cracking of the piccolo ducts in accordance with the Accomplishment 
Instructions of Bombardier Alert Service Bulletin A601R-30-032, 
dated September 18, 2008. If no cracking is found, repeat the 
inspection thereafter at intervals not to exceed 2,000 flight hours. 
Doing the action specified in paragraph (w) of this AD terminates 
the requirements of this paragraph.
    (t) If any cracking is found during any inspection required by 
paragraph (s) of this AD, before further flight, do the actions 
specified in paragraph (t)(1), (t)(2), or (t)(3) of this AD, except 
where Bombardier Alert Service Bulletin A601R-30-032, dated 
September 18, 2008, specifies to contact Bombardier for information 
regarding repair, this AD requires repair according to a method 
approved by either the Manager, New York ACO, or TCCA (or its 
delegated agent). Doing the action specified in paragraph (w) of 
this AD terminates the requirements of this paragraph.
    (1) Replace the cracked piccolo duct, in accordance with the 
Accomplishment Instructions of Bombardier Alert Service Bulletin 
A601R-30-032, dated September 18, 2008, with a new piccolo duct that 
has the same part number as identified in Part A, Paragraph 2.A., of 
the Accomplishment Instructions of Bombardier Alert Service Bulletin 
A601R-30-032, dated September 18, 2008, but that does not have a 
serial number listed in that paragraph.
    (2) Replace the cracked piccolo duct, in accordance with the 
Accomplishment Instructions of Bombardier Alert Service Bulletin 
A601R-30-032, dated September 18, 2008, with a new piccolo duct that 
has a part number identified in the applicable Bombardier 
illustrated parts catalog but not identified in Part A, Paragraph 
2.A., of the Accomplishment Instructions of Bombardier Alert Service 
Bulletin A601R-30-032, dated September 18, 2008.
    (3) Replace the cracked piccolo duct with a piccolo duct that 
has been repaired in accordance with a method approved by either the 
Manager, New York ACO, FAA; or TCCA (or its delegated agent).

Repetitive Inspection of the Wing Anti-Ice Piccolo Ducts

    (u) For airplanes on which an inspection required by paragraph 
(h)(1) of this AD has been done, except for airplanes on which the 
terminating action specified in paragraph (l) of this AD has been 
done: Within 2,000 flight hours since the last inspection, or 30 
days after the effective date of this AD, whichever occurs later, do 
the actions specified in paragraph (s) of this AD. Doing the 
inspection required by this paragraph terminates the actions 
required by paragraph (h)(1) of this AD. Doing the action specified 
in paragraph (w) of this AD terminates the requirements of this 
paragraph.

New Parts Installation Paragraph

    (v) As of the effective date of this AD, the requirements 
specified in paragraphs (v)(1) and (v)(2) of this AD must be 
followed.
    (1) For airplanes on which the terminating action specified in 
paragraph (w) of this AD has not been done: No person may install a 
piccolo duct having a part number identified in Part A, Paragraph 
2.A., of the Accomplishment Instructions of Bombardier Alert Service 
Bulletin A601R-30-032, dated September 18, 2008, on any airplane, 
unless the requirements specified in paragraphs (s) and (t) of this 
AD, as applicable, have been accomplished for that piccolo duct.
    (2) For airplanes on which the terminating action specified in 
paragraph (w) of this AD

[[Page 67368]]

has been done: No person may install a piccolo duct having a part 
number identified in Part A, Paragraph 2.A., of the Accomplishment 
Instructions of Bombardier Alert Service Bulletin A601R-30-032, 
dated September 18, 2008, on any airplane.

Optional Terminating Action

    (w) Replacing all piccolo ducts that have serial numbers 
identified in Part A, Paragraph 2.A., of the Accomplishment 
Instructions of Bombardier Alert Service Bulletin A601R-30-032, 
dated September 18, 2008, with piccolo ducts that do not have serial 
numbers identified in Part A, Paragraph 2.A., of the Accomplishment 
Instructions of Bombardier Alert Service Bulletin A601R-30-032, 
dated September 18, 2008, in accordance with the Accomplishment 
Instructions of Bombardier Alert Service Bulletin A601R-30-032, 
dated September 18, 2008, terminates the requirements of paragraphs 
(f), (h), (i), (p), (q), (r), (s), (t), and (u) of this AD.

Optional Service Information for Certain Requirements of This AD

    (x) Actions accomplished according to Bombardier Service 
Bulletin 601R-30-029, Revision B, dated August 29, 2005; or 
Bombardier Alert Service Bulletin A601R-30-032, dated September 18, 
2008; are considered acceptable for compliance with the 
corresponding actions specified in paragraphs (h)(1), (j)(1), 
(j)(2), (j)(3), and (l) of this AD.

Alternative Methods of Compliance (AMOCs)

    (y) The Manager, New York ACO, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. Send information to ATTN: Fabio Buttitta, Aerospace Engineer, 
New York Aircraft Certification Office, ANE-171, FAA, New York 
Aircraft Certification Office, 1600 Stewart Avenue, Suite 410, 
Westbury, New York 11590; telephone (516) 228-7303; fax (516) 794-
5531. Before using any approved AMOC on any airplane to which the 
AMOC applies, notify your appropriate principal inspector (PI) in 
the FAA Flight Standards District Office (FSDO), or lacking a PI, 
your local FSDO.

Related Information

    (z) Canadian airworthiness directive CF-2008-30, dated October 
7, 2008, also addresses the subject of this AD.

Material Incorporated by Reference

    (aa) You must use the service information listed in Table 1 of 
this AD to perform the actions that are required by this AD, as 
applicable, unless the AD specifies otherwise.

               Table 1--Material Incorporated by Reference
------------------------------------------------------------------------
      Service information           Revision level            Date
------------------------------------------------------------------------
Bombardier Alert Service        Original..............  September 18,
 Bulletin A601R-30-032,                                  2008.
 including Appendix A and
 Appendix B.
Bombardier Service Bulletin     A.....................  July 7, 2005.
 601R-30-029, including
 Appendix A, dated June 17,
 2005, and Appendix B,
 Revision A, dated July 7,
 2005.
Canadair (Bombardier)           Original..............  September 17,
 Temporary Revision RJ/155-6                             2008.
 to the Canadair Regional Jet
 Airplane Flight Manual, CSP A-
 012.
Canadair Temporary Revision RJ/ Original..............  July 5, 2005.
 155 to the Canadair Regional
 Jet Airplane Flight Manual,
 CSP A-012.
------------------------------------------------------------------------

    (1) The Director of the Federal Register approved the 
incorporation by reference of Bombardier Alert Service Bulletin 
A601R-30-032, including Appendix A and Appendix B, dated September 
18, 2008; and Canadair (Bombardier) Temporary Revision RJ/155-6 to 
the Canadair Regional Jet Airplane Flight Manual, CSP A-012, dated 
September 17, 2008; in accordance with 5 U.S.C. 552(a) and 1 CFR 
part 51.
    (2) On September 7, 2005 (70 FR 49164, August 23, 2005), the 
Director of the Federal Register approved the incorporation by 
reference of Canadair Temporary Revision RJ/155, dated July 5, 2005, 
to the Canadair Regional Jet Airplane Flight Manual, CSP A-012; and 
Bombardier Service Bulletin 601R-30-029, Revision A, dated July 7, 
2005, including Appendix A, dated June 17, 2005, and Appendix B, 
Revision A, dated July 7, 2005.
    (3) Contact Bombardier, Inc., Canadair, Aerospace Group, P.O. 
Box 6087, Station Centre-ville, Montreal, Quebec H3C 3G9, Canada; 
telephone 514-855-8500; fax 514-855-8501; E-mail 
[email protected]; Internet http://www.bombardier.com; for 
a copy of this service information. You may review copies at the 
FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, 
Washington; or at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

    Issued in Renton, Washington, on November 4, 2008.
Stephen P. Boyd,
Assistant Manager, Transport Airplane Directorate, Aircraft 
Certification Service.
[FR Doc. E8-26911 Filed 11-13-08; 8:45 am]
BILLING CODE 4910-13-P