[Federal Register Volume 72, Number 117 (Tuesday, June 19, 2007)]
[Rules and Regulations]
[Pages 33639-33642]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: E7-11241]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2007-28251; Directorate Identifier 2007-CE-049-AD; 
Amendment 39-15099; AD 2007-12-21]
RIN 2120-AA64


Airworthiness Directives; Hawker Beechcraft Corporation (Type 
Certificate No. A00010WI Previously Held by Raytheon Aircraft Company) 
Model 390 Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) to 
supersede AD 2006-26-08, which applies to all Hawker Beechcraft 
Corporation (HBC) Model 390 airplanes. AD 2006-26-08 currently requires 
you to repetitively inspect the hydraulic pump outlet tube on both 
engines and immediately replace the tube if damage is found. AD 2006-
26-08 also requires you to incorporate an airplane flight manual (AFM) 
change that limits operation of an engine with its associated firewall 
hydraulic shutoff valve closed. If an engine is operated with its 
firewall hydraulic shutoff valve closed, you must replace the hydraulic 
pump outlet tube. We issued AD 2006-26-08 as an interim action while we 
worked with the type certificate holder to develop a design change. HBC 
has

[[Page 33640]]

now developed kits that incorporate design changes for the hydraulic 
pump outlet tubes and dampener supports so this AD retains the actions 
of AD 2006-26-08 until the new modification kits required by this AD 
are installed. We continued to receive additional reports of failures 
of the hydraulic pump outlet tube. We are issuing this AD to prevent 
failure of the hydraulic pump outlet tube and consequent leaking of 
hydraulic fluid. Such leakage could result in a fire. There is also a 
risk of loss of hydraulic system functions including normal gear 
extensions, speed brakes, roll spoilers, lift dump, and normal brakes.

DATES: This AD becomes effective on June 20, 2007.
    On June 20, 2007, the Director of the Federal Register approved the 
incorporation by reference of Raytheon Aircraft Company Kit--Dampener 
Support Improvement, Drawing No. 390-5804 (Kit 390-5804-0001 Field 
Service Kit) and Raytheon Aircraft Company Kit--Hydraulic Pump Pressure 
Hose Installation No. 390-5805 (Kit 390-5805-0001 Field Service Kit), 
as referenced in Hawker Beechcraft Mandatory Service Bulletin 29-3800, 
Issued May 2007, as listed in this AD.
    As of February 2, 2006 (71 FR 5581, February 2, 2006), the Director 
of the Federal Register approved the incorporation by reference of 
Raytheon Mandatory Service Bulletin No. SB 29-3771, dated January 2006; 
and Raytheon Safety Communique No. 267, dated January 2006, as listed 
in this AD.
    We must receive any comments on this AD by August 20, 2007.

ADDRESSES: Use one of the following addresses to comment on this AD.
     DOT Docket Web site: Go to http://dms.dot.gov and follow 
the instructions for sending your comments electronically.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590.
     Fax: (202) 493-2251.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590 between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
    To get the service information identified in this AD, contact 
Hawker Beechcraft Corporation, 9709 East Central, Wichita, Kansas 
67291; telephone: (800) 429-5372 or (316) 676-3140.
    To view the comments to this AD, go to http://dms.dot.gov. The 
docket number is FAA-2007-28251; Directorate Identifier 2007-CE-049-AD.

FOR FURTHER INFORMATION CONTACT: James P. Galstad, Propulsion Aerospace 
Engineer, ACE 116W, Wichita Aircraft Certification Office, 1801 Airport 
Road, Room 100, Wichita, Kansas 67209; telephone: (316) 946-4135; fax: 
(316) 946-4107.

SUPPLEMENTARY INFORMATION:

Discussion

    Reports of left engine hydraulic tube assembly failures prompted us 
to issue AD 2006-02-51, Amendment 39-14459 (71 FR 5581, February 2, 
2006). AD 2006-02-51 required repetitive inspection of the hydraulic 
tube assembly, correction of the symptomatic clamp to hydraulic tube 
chafing on the left-hand nacelle, and reporting results to the FAA.
    After we issued AD 2006-02-51, we continued to receive additional 
reports of failures of the hydraulic pump outlet tube, including 
failures on the right engine on certain HBC Model 390 airplanes. This 
prompted us to supersede AD 2006-02-51 with AD 2006-26-08, Amendment 
39-14866 (71 FR 78051, December 28, 2006).
    AD 2006-26-08 currently requires you to repetitively inspect the 
hydraulic pump outlet tube on both engines and immediately replace the 
tube if damage is found. AD 2006-26-08 also requires you to incorporate 
an airplane flight manual (AFM) change that limits operation of an 
engine with its associated firewall hydraulic shutoff valve closed. If 
an engine is operated with its firewall hydraulic shutoff valve closed, 
you must replace the hydraulic pump outlet tube.
    We issued AD 2006-26-08 as an interim action while we worked with 
the type certificate holder to develop a design change. We continued to 
receive additional reports of failures of the hydraulic pump outlet 
tube.
    HBC has now developed kits that incorporate design changes for the 
hydraulic pump outlet tubes and dampener supports.
    Failure of the hydraulic pump outlet tubes, if not prevented, could 
cause flammable fluid leakage in the engine nacelle. Such leakage could 
result in a fire. There is also a risk of loss of hydraulic system 
functions including normal gear extensions, speed brakes, roll 
spoilers, lift dump, and normal brakes.

Relevant Service Information

    We reviewed Hawker Beechcraft Mandatory Service Bulletin No. 29-
3800, issued May 2007. The service information specifies the following 
actions:
     Incorporating Kit No. 390-5804-0001, which replaces the 
pulse dampener brackets with stiffer brackets and a spacer on both 
engines; and
     Incorporating Kit No. 390-5805-0001, which replaces the 
hydraulic pump outlet tubes with integral firesleeve hoses.
    Raytheon Mandatory Service Bulletin No. SB 29-3771, dated January 
2006; and Raytheon Safety Communique No. 267, dated January 2006, will 
be retained for this AD until both kits referenced above are 
incorporated.

FAA's Determination and Requirements of This AD

    We are issuing this AD because we evaluated all the information and 
determined the unsafe condition described previously is likely to exist 
or develop on other products of the same type design. This AD retains 
the actions of AD 2006-26-08 and requires incorporating Kit No. 390-
5804-0001 and Kit No. 390-5805-0001. Upon incorporating the kits 
required by this AD, the repetitive inspections and replacement 
retained from AD 2006-26-08 are no longer necessary. The AFM limitation 
is still required.
    We continue to work with HBC in analyzing the design of the 
hydraulic system of the Model 390 airplanes. Based on this analysis, we 
may take future rulemaking action, which could eliminate the need for 
the current AFM limitation.
    In preparing this rule, we contacted type clubs and aircraft 
operators to get technical information and information on operational 
and economic impacts. We did not receive any information through these 
contacts. If received, we would have included a discussion of any 
information that may have influenced this action in the rulemaking 
docket.

FAA's Determination of the Effective Date

    Since an unsafe condition exists that requires the immediate 
adoption of this AD, we determined that notice and opportunity for 
public comment before issuing this AD are impracticable, and that good 
cause exists for making this amendment effective in fewer than 30 days.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety, and

[[Page 33641]]

we did not precede it by notice and an opportunity for public comment. 
We invite you to send any written relevant data, views, or arguments 
regarding this AD. Send your comments to an address listed under the 
ADDRESSES section. Include the docket number ``FAA-2007-28251; 
Directorate Identifier 2007-CE-049-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of the AD. We will consider 
all comments received by the closing date and may amend the AD in light 
of those comments.
    We will post all comments we receive, without change, to http://dms.dot.gov, including any personal information you provide. We will 
also post a report summarizing each substantive verbal contact we 
receive concerning this AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866;
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979); and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this AD and placed it in the AD docket.

Examining the AD Docket

    You may examine the AD docket that contains the AD, the regulatory 
evaluation, any comments received, and other information on the 
Internet at http://dms.dot.gov; or in person at the Docket Management 
Facility between 9 a.m. and 5 p.m., Monday through Friday, except 
Federal holidays. The Docket Office (telephone (800) 647-5227) is 
located at the street address stated in the ADDRESSES section. Comments 
will be available in the AD docket shortly after receipt.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by removing Airworthiness Directive (AD) 
2006-26-08, Amendment 39-14866 (71 FR 78051, December 28, 2006), and by 
adding a new AD to read as follows:

2007-12-21 Hawker Beechcraft Corporation (Type Certificate No. 
A00010WI previously held by Raytheon Aircraft Company): Amendment 
39-15099; Docket No. FAA-2007-28251; Directorate Identifier 2007-CE-
049-AD.

Effective Date

    (a) This AD becomes effective on June 20, 2007.

Affected ADs

    (b) This AD supersedes AD 2006-26-08; Amendment 39-14866.

Applicability

    (c) This AD affects the following Model 390 airplanes that are 
certificated in any category:
    (1) Serial numbers RB-1 through RB-49 that have Field Service 
Kit 390-9100 installed; and
    (2) Serial numbers RB-50 through RB-209.

Unsafe Condition

    (d) This AD is the result of continuing failures of the 
hydraulic pump outlet tubes and the need to incorporate improved 
design. We are issuing this AD to prevent failure of the hydraulic 
pump outlet tube and consequent leaking of hydraulic fluid. Such 
leakage could result in a fire. There is also a risk of loss of 
hydraulic system functions including normal gear extensions, speed 
brakes, roll spoilers, lift dump, and normal brakes.

Compliance

    (e) To address this problem, you must do the following, unless 
already done:

------------------------------------------------------------------------
             Actions                  Compliance          Procedures
------------------------------------------------------------------------
(1) Visually inspect the          Initially at        Inspect following
 hydraulic pump outlet tube for    whichever of the    Raytheon Safety
 evidence of chafing, excessive    following occurs    Communique No.
 vibration, wear, deterioration,   first and           267, dated
 or hydraulic fluid leakage, as    thereafter at       January 2006.
 follows:                          intervals not to    Raytheon Safety
(i) For the left-hand (LH)         exceed 25 hours     Communique No.
 engine: Remove the clamp,         time-in-service     267, dated
 perform the inspection, and       (TIS) until the     January 2006,
 replace the clamp with a new      kits required in    addresses the LH
 one as specified in Raytheon      paragraph (e)(4)    engine. Use the
 Mandatory Service Bulletin No.    of this AD are      same inspection
 SB 29-3771 after each             incorporated:       procedures for
 inspection.                      (A) Within the       the RH engine
(ii) For the right-hand (RH)       next 25 hours TIS   hydraulic pump
 engine: Perform the inspection.   after December      outlet tube (P/N
 Removal and replacement of the    28, 2006 (the       390-580037).
 clamps are not necessary.         effective date of   Remove and
                                   AD 2006-26-08);     replace the clamp
                                   or.                 (LH only)
                                  (B) At the next      following
                                   inspection          Raytheon
                                   required by AD      Mandatory Service
                                   2006-02-51..        Bulletin No. SB
                                                       29-3771, dated
                                                       January, 2006.

[[Page 33642]]

 
(2) Replace the hydraulic pump    Each and every      Raytheon Aircraft
 outlet tube, part number (P/N)    time any of the     Premier 1 Model
 390-580035 (or FAA-approved       following occurs    390 Maintenance
 equivalent) for the LH engine     until the kits      Manual, P/N 390-
 or P/N 390-580037 (or FAA-        required in         590001-0015.
 approved equivalent) for the RH   paragraph (e)(4)
 engine.                           of this AD are
                                   incorporated
                                  (i) Prior to
                                   further flight
                                   after any
                                   inspection
                                   required in
                                   paragraph (e)(1)
                                   of this AD where
                                   evidence of
                                   chafing,
                                   excessive
                                   vibration, wear,
                                   deterioration, or
                                   hydraulic fluid
                                   leakage is found;
                                   and.
                                  (ii) Within 1 hour
                                   TIS following
                                   identification of
                                   an intended or
                                   unintended engine
                                   operation with
                                   the hydraulic
                                   shutoff valve
                                   closed..
(3) Incorporate Raytheon          Within 5 days       The owner/operator
 Aircraft Company Part Number      after December      holding at least
 390-590001-0003C3TC6, dated       28, 2006 (the       a private pilot
 September 16, 2006 into the       effective date of   certificate as
 airplane flight manual (AFM).     AD 2006-26-08).     authorized by
                                                       section 43.7 of
                                                       the Federal
                                                       Aviation
                                                       Regulations (14
                                                       CFR 43.7) may do
                                                       the AFM change
                                                       requirement of
                                                       this AD. Make an
                                                       entry into the
                                                       aircraft records
                                                       showing
                                                       compliance with
                                                       this portion of
                                                       the AD in
                                                       accordance with
                                                       section 43.9 of
                                                       the Federal
                                                       Aviation
                                                       Regulations (14
                                                       CFR 43.9).
(4) Incorporate Kits No. 390-     At whichever of     Follow the
 5804-0001 and 390-5805-0001.      the following       instructions in
                                   that occurs         the documents
                                   first:              presented below
                                  (i) Within the       as referenced in
                                   next 25 hours TIS   Hawker Beechcraft
                                   after June 20,      Mandatory Service
                                   2007 (the           Bulletin 29-3800,
                                   effective date of   Issued May, 2007:
                                   this AD); or.      (i) Raytheon
                                  (ii) Within the      Aircraft Company
                                   next 45 days        Kit--Dampener
                                   after June 20,      Support
                                   2007 (the           Improvement,
                                   effective date of   Drawing No. 390-
                                   this AD..           5804 (Kit 390-
                                                       5804-0001 Field
                                                       Service Kit).
                                                      (ii) Raytheon
                                                       Aircraft Company
                                                       Kit--Hydraulic
                                                       Pump Pressure
                                                       Hose Installation
                                                       No. 390-5805 (Kit
                                                       390-5805-0001
                                                       Field Service
                                                       Kit).
------------------------------------------------------------------------

    (f) After the actions required in paragraph (e)(4) of this AD 
are done:
    (1) the repetitive inspections and replacement of paragraphs 
(e)(1) and (e)(2) of this AD are no longer required.
    (2) the requirement in paragraph (e)(3) of this AD to 
incorporate Raytheon Aircraft Company Part Number 390-590001-
0003C3TC6, dated September 16, 2006, into the AFM remains valid.

Alternative Methods of Compliance (AMOCs)

    (g) The Manager, Wichita Aircraft Certification Office, FAA, 
ATTN: James P. Galstad, Propulsion Aerospace Engineer, ACE 116W, 
Wichita Aircraft Certification Office, 1801 Airport Road, Room 100, 
Wichita, Kansas 67209; telephone: (316) 946-4135; fax: (316) 946-
4107, has the authority to approve AMOCs for this AD, if requested 
using the procedures found in 14 CFR 39.19. Before using any 
approved AMOC on any airplane to which the AMOC applies, notify your 
appropriate principal inspector (PI) in the FAA Flight Standards 
District Office (FSDO), or lacking a PI, your local FSDO.
    (h) AMOCs approved for AD 2006-26-08 are approved for this AD.

Material Incorporated by Reference

    (i) You must use Raytheon Mandatory Service Bulletin No. SB 29-
3771, dated January, 2006; Raytheon Safety Communique No. 267, dated 
January 2006; and Raytheon Aircraft Company Kit--Dampener Support 
Improvement, Drawing No. 390-5804 (Kit 390-5804-0001 Field Service 
Kit) and Raytheon Aircraft Company Kit--Hydraulic Pump Pressure Hose 
Installation No. 390-5805 (Kit 390-5805-0001 Field Service Kit), as 
referenced in Hawker Beechcraft Mandatory Service Bulletin 29-3800, 
Issued May, 2007, to do the actions required by this AD, unless the 
AD specifies otherwise.
    (1) The Director of the Federal Register approved the 
incorporation by reference of Raytheon Aircraft Company Kit--
Dampener Support Improvement, Drawing No. 390-5804 (Kit 390-5804-
0001 Field Service Kit) and Raytheon Aircraft Company Kit--Hydraulic 
Pump Pressure Hose Installation No. 390-5805 (Kit 390-5805-0001 
Field Service Kit), as referenced in Hawker Beechcraft Mandatory 
Service Bulletin 29-3800, Issued May, 2007, under 5 U.S.C. 552(a) 
and 1 CFR part 51.
    (2) On February 2, 2006 (71 FR 5581, February 2, 2006), the 
Director of the Federal Register approved the incorporation by 
reference of Raytheon Mandatory Service Bulletin No. SB 29-3771, 
dated January, 2006; and Raytheon Safety Communique No. 267, dated 
January 2006.
    (3) For service information identified in this AD, contact 
Hawker Beechcraft Corporation, 9709 East Central, Wichita, Kansas 
67291; telephone: (800) 429-5372 or (316) 676-3140.
    (4) You may review copies at the FAA, Central Region, Office of 
the Regional Counsel, 901 Locust, Kansas City, Missouri 64106; or at 
the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, call 202-
741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

    Issued in Kansas City, Missouri, on June 4, 2007.
David R. Showers,
Acting Manager, Small Airplane Directorate, Aircraft Certification 
Service.
 [FR Doc. E7-11241 Filed 6-18-07; 8:45 am]
BILLING CODE 4910-13-P