[Federal Register Volume 72, Number 98 (Tuesday, May 22, 2007)]
[Rules and Regulations]
[Pages 28597-28601]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: E7-9801]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2007-28253; Directorate Identifier 2007-NM-031-AD; 
Amendment 39-15064; AD 2007-11-07]
RIN 2120-AA64


Airworthiness Directives; Boeing Model 737-100, -200, -200C, -
300, -400, and -500 Series Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

[[Page 28598]]


ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: The FAA is superseding an existing airworthiness directive 
(AD) that applies to all Model 737-100, -200, -300, -400, and -500 
series airplanes. The existing AD currently requires repetitive 
detailed inspections for damage of the electrical wire and sleeve that 
run through a conduit in the fuel tank to the fuel boost pump, and 
related investigative and corrective actions; as applicable. This new 
AD removes certain inspection requirements. This new AD adds repetitive 
detailed inspections for damage of the electrical wire and sleeve that 
run to the fuel boost pump through a conduit in the fuel tank, and 
arcing damage of the conduit and signs of fuel leakage into the 
conduit; replacement of the sleeve with a new, smaller-diameter sleeve; 
and related investigative and corrective actions, as applicable. This 
AD also adds airplanes to the applicability. Accomplishment of the 
initial new inspection and the sleeve installation terminates the 
requirements of the existing AD. This new AD results from a report of a 
fuel tank explosion on a Model 727-200F airplane on the ground, and a 
report of chafed wires and a damaged power cable sleeve of a fuel boost 
pump discovered during an inspection on a Model 737-300 airplane. We 
are issuing this AD to detect and correct chafing of the fuel boost 
pump electrical wiring and leakage of fuel into the conduit, and to 
prevent electrical arcing between the wiring and the surrounding 
conduit, which could result in arc-through of the conduit, and 
consequent fire or explosion of the fuel tank.

DATES: This AD becomes effective June 6, 2007.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in the AD as of June 6, 2007.
    On November 12, 1999 (64 FR 54763, October 8, 1999), the Director 
of the Federal Register approved the incorporation by reference of 
Boeing Alert Service Bulletin 737-28A1120, Revision 2, dated November 
26, 1998.
    On October 15, 1998 (63 FR 52152, September 30, 1998), the Director 
of the Federal Register approved the incorporation by reference of 
Boeing Alert Service Bulletin 737-28A1120, Revision 1, dated May 28, 
1998.
    On June 29, 1998 (63 FR 34271, June 24, 1998), the Director of the 
Federal Register approved the incorporation by reference of Boeing 
Alert Service Bulletin 737-28A1120, dated April 24, 1998, as revised by 
Notice of Status Change NSC 01, dated May 7, 1998, Notice of Status 
Change NSC 02, dated May 8, 1998, and Notice of Status Change NSC 03, 
dated May 9, 1998.
    We must receive any comments on this AD by July 23, 2007.

ADDRESSES: Use one of the following addresses to submit comments on 
this AD.
     DOT Docket Web site: Go to http://dms.dot.gov and follow 
the instructions for sending your comments electronically.
     Government-wide rulemaking Web site: Go to http://www.regulations.gov and follow the instructions for sending your 
comments electronically.
     Mail: Docket Management Facility; U.S. Department of 
Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401, 
Washington, DC 20590.
     Fax: (202) 493-2251.
     Hand Delivery: Room PL-401 on the plaza level of the 
Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    Contact Boeing Commercial Airplanes, P.O. Box 3707, Seattle, 
Washington 98124-2207, for service information identified in this AD.
    You may examine the contents of the AD docket on the Internet at 
http://dms.dot.gov, or in person at the Docket Management Facility, 
U.S. Department of Transportation, 400 Seventh Street, SW., Room PL-
401, Washington, DC. This docket number is FAA-2007-28253; the 
directorate identifier for this docket is 2007-NM-031-AD.

FOR FURTHER INFORMATION CONTACT: Suzanne Lucier, Aerospace Engineer, 
Propulsion Branch, ANM-140S, FAA, Seattle Aircraft Certification 
Office, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone 
(425) 917-6438; fax (425) 917-6590.

SUPPLEMENTARY INFORMATION: 

Discussion

    On September 29, 1999, we issued AD 99-21-15, amendment 39-11360 
(64 FR 54763, October 8, 1999). That AD applies to certain Boeing Model 
737-100, -200, -300, -400, and -500 series airplanes. That AD requires 
repetitive detailed inspections for damage of the electrical wire and 
sleeve that run through a conduit in the fuel tank to the fuel boost 
pump, and related investigative and corrective actions, as applicable. 
That AD resulted from reports of severe wear of the fuel boost pump 
wiring due to chafing between the wiring and the surrounding conduit 
inside the fuel tank, pin-hole-sized holes in the conduit that appear 
to be the result of arc-through of the conduit, and exposure of the 
main tank boost pump wire conductor inside a conduit and signs of 
arcing to the wall of the conduit. The actions specified in that AD are 
intended to detect and correct chafing and prevent electrical arcing 
between the fuel boost pump electrical wiring and the surrounding 
conduit, which could result in arc-through of the conduit, and 
consequent fire or explosion of the fuel tank.

Actions Since AD Was Issued

    Since we issued that AD, we received a report that a fuel tank 
explosion occurred on a Model 727-200F airplane on the ground. 
Investigation revealed evidence of arcing in the metal conduit that 
carries power wires from the front spar through the fuel tank to the 
dry bay of the 1 aft fuel boost pump. In a separate incident, 
we received a report from Boeing indicating that chafed wires and a 
damaged power cable sleeve of a fuel boost pump were discovered during 
a repetitive inspection of the power cable and sleeve of a Model 737-
300 airplane; that inspection was done at approximately 21,000 flight 
hours rather than the repetitive interval of 30,000 flight hours 
specified by the existing AD. The fuel boost pump installation on 
certain Model 737 airplanes is almost identical to the installation on 
Model 727 airplanes.
    We have also determined that Model 737-200C series airplanes are 
also subject to the unsafe condition identified in AD 99-21-15.

Other Relevant Rulemaking

    Operators should note that we are considering issuing a separate AD 
to address the identified unsafe condition as it relates to Model 727 
airplanes.

Relevant Service Information

    We have reviewed Boeing Alert Service Bulletin 737-28A1263, 
Revision 1, dated March 19, 2007. This service bulletin differs from 
the service information cited in AD 99-21-15 in the following ways. The 
alert service bulletin describes procedures for performing new 
repetitive detailed inspections for damage of the electrical wire and 
sleeve that run to the fuel boost pump through a conduit in the fuel 
tank, and arcing damage of the conduit and signs of fuel leakage into 
the conduit; replacing the sleeve with a new, smaller-diameter sleeve; 
performing related investigative and corrective actions, as applicable; 
and reporting inspection results and returning damaged parts to the 
manufacturer. The repetitive interval for the detailed inspections is 
15,000 flight hours (rather than 30,000 flight hours,

[[Page 28599]]

as required by AD 99-21-15). Related investigative and corrective 
actions include replacing, with BMS 13-60T09C03G018 wire, any wire that 
is damaged or has any part number other than BMS 13-60T09C03G018 or BMS 
13-60T12C03G018; doing leak testing of the conduit if signs of fuel are 
discovered on the wire or sleeve during any inspection; and repairing 
any damaged conduit or replacing it with a new conduit.

FAA's Determination and Requirements of This AD

    The unsafe condition described previously is likely to exist or 
develop on other airplanes of the same type design. For this reason, we 
are issuing this AD to supersede AD 99-21-15. This new AD retains 
certain requirements of the existing AD. This AD also requires 
accomplishing the actions specified in the alert service bulletin 
described previously.

Changes to Existing AD

    Instead of restating all of the corrective actions specified in AD 
99-21-15, that is, paragraphs (h), (i), (j), and (k), we simplified 
these requirements by consolidating them into paragraph (j) in this AD. 
We have verified that all of the information of paragraphs (h), (i), 
(j), and (k) of AD 99-21-15 is contained in the service bulletin 
references identified in paragraph (j) of this AD.

Clarification of Applicability

    The applicability of AD 99-21-15 did not specifically list Model 
737-200C series airplanes. Likewise, the service information (Boeing 
Service Bulletin 737-28A1120, original version, Revision 1, and 
Revision 2) cited in that AD did not specifically identify Model 737-
200C series airplanes in the effectivity, although Revision 3 did 
identify them. Because the unsafe condition could occur on those 
airplanes, this AD adds them to the applicability to ensure that the 
actions required by this AD are accomplished on all affected airplanes. 
We recognize that some of these airplanes might have already been 
inspected as specified in the existing AD. In order to give credit for 
work accomplished on these airplanes, this AD adds a compliance time 
for the initial inspection relative to the date of the most recent 
inspection done in accordance with Service Bulletin 737-28A1120.

Interim Action

    We consider this AD interim action. If final action is later 
identified, we may consider further rulemaking then.

Explanation of Compliance Time

    The compliance time for the new inspection in this AD is 120 days. 
Based on the large number of affected U.S.-registered airplanes and the 
amount of time required to accomplish the required actions, including 
corrective actions, we consider that this compliance time is necessary 
to avoid unnecessarily disrupting flight schedules.

FAA's Determination of the Effective Date

    An unsafe condition exists that requires the immediate adoption of 
this AD; therefore, providing notice and opportunity for public comment 
before the AD is issued is impracticable, and good cause exists to make 
this AD effective in less than 30 days.

Comments Invited

    This AD is a final rule that involves requirements that affect 
flight safety and was not preceded by notice and an opportunity for 
public comment; however, we invite you to submit any relevant written 
data, views, or arguments regarding this AD. Send your comments to an 
address listed in the ADDRESSES section. Include ``Docket No. FAA-2007-
28253; Directorate Identifier 2007-NM-031-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of the AD that might 
suggest a need to modify it.
    We will post all comments we receive, without change, to http://
http://dms.dot.gov">dms.dot.gov, including any personal information you provide. We will 
also post a report summarizing each substantive verbal contact with FAA 
personnel concerning this AD. Using the search function of that Web 
site, anyone can find and read the comments in any of our dockets, 
including the name of the individual who sent the comment (or signed 
the comment on behalf of an association, business, labor union, etc.). 
You may review the DOT's complete Privacy Act Statement in the Federal 
Register published on April 11, 2000 (65 FR 19477-78), or you may visit 
http://dms.dot.gov.

Examining the Docket

    You may examine the AD docket on the Internet at http://
http://dms.dot.gov">dms.dot.gov, or in person at the Docket Management Facility office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The Docket Management Facility office (telephone (800) 647-
5227) is located on the plaza level of the Nassif Building at the DOT 
street address stated in the ADDRESSES section. Comments will be 
available in the AD docket shortly after the Docket Management System 
receives them.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We have determined that this AD will not have federalism 
implications under Executive Order 13132. This AD will not have a 
substantial direct effect on the States, on the relationship between 
the national government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that the regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this AD and placed it in the AD docket. See the ADDRESSES 
section for a location to examine the regulatory evaluation.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the FAA amends part 39 of the Federal Aviation Regulations (14 CFR part 
39) as follows:

[[Page 28600]]

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The Federal Aviation Administration (FAA) amends Sec.  39.13 by 
removing amendment 39-11360 (64 FR 54763, October 8, 1999) and adding 
the following new airworthiness directive (AD):

2007-11-07 Boeing: Docket No. FAA-2007-28253; Directorate Identifier 
2007-NM-031-AD; Amendment 39-15064.

Effective Date

    (a) This AD becomes effective June 6, 2007.

Affected ADs

    (b) This AD supersedes AD 99-21-15.

Applicability

    (c) This AD applies to all Boeing Model 737-100, -200, -200C, -
300, -400, and -500 series airplanes, certificated in any category.

Unsafe Condition

    (d) This AD results from a report of a fuel tank explosion on a 
Model 727-200F airplane on the ground, and a report of chafed wires 
and a damaged power cable sleeve of a fuel boost pump discovered 
during an inspection on a Model 737-300 airplane. (The fuel boost 
pump installation on certain Model 737 airplanes is almost identical 
to the installation on Model 727 airplanes.) We are issuing this AD 
to detect and correct chafing of the fuel boost pump electrical 
wiring and leakage of fuel into the conduit, and to prevent 
electrical arcing between the wiring and the surrounding conduit, 
which could result in arc-through of the conduit, and consequent 
fire or explosion of the fuel tank.

Compliance

    (e) You are responsible for having the actions required by this 
AD performed within the compliance times specified, unless the 
actions have already been done.

Restatement of Certain Requirements of AD 99-21-15

Certain Inspections Required by AD 98-11-52

    (f) For Model 737-100, -200, -300, -400, and -500 series 
airplanes: Prior to the accumulation of 30,000 total flight hours or 
within 45 days after June 29, 1998 (the effective date of AD 98-11-
52, amendment 39-10611, which was superseded by AD 98-19-09), 
whichever occurs later, remove the fuel boost pump wiring from the 
in-tank conduit for the aft boost pumps in main tanks numbers 1 and 
2, and the center tank left and right boost pumps, and perform a 
detailed visual inspection to detect damage of the wiring, in 
accordance with the procedures specified in Boeing Alert Service 
Bulletin 737-28A1120, dated April 24, 1998, as revised by Notices of 
Status Change NSC 01, dated May 7, 1998, NSC 02, dated May 8, 1998, 
and NSC 03, dated May 9, 1998; Revision 1, dated May 28, 1998; or 
Revision 2, dated November 26, 1998.

Inspections Required by AD 98-19-09

    (g) For Model 737-100, -200, -300, -400, and -500 series 
airplanes that have accumulated 20,000 or more total flight hours 
and less than 30,000 total flight hours as of October 15, 1998 (the 
effective date of AD 98-19-09, amendment 39-10751, which was 
superseded by AD 99-21-15): Within 60 days after October 15, 1998, 
remove the fuel boost pump wiring from the in-tank conduit for the 
aft boost pumps in main tanks numbers 1 and 2, and the center tank 
left and right boost pumps, and perform a detailed visual inspection 
to detect damage of the wiring; in accordance with the procedures 
specified in Boeing Alert Service Bulletin 737-28A1120, dated April 
24, 1998, as revised by Notices of Status Change NSC 01, dated May 
7, 1998, NSC 02, dated May 8, 1998, and NSC 03, dated May 9, 1998; 
Revision 1, dated May 28, 1998; or Revision 2, dated November 26, 
1998.

Inspections Required by AD 99-21-15

    (h) For Model 737-100, -200, -300, -400, and -500 series 
airplanes: Remove the fuel boost pump wiring from the in-tank 
conduit for the aft boost pumps in main tanks numbers 1 and 2, and 
the center tank left and right boost pumps, and perform a detailed 
visual inspection to detect damage of the wiring; at the time 
specified in paragraph (h)(1) or (h)(2) of this AD, as applicable. 
Perform these actions in accordance with the procedures specified in 
Boeing Alert Service Bulletin 737-28A1120, dated April 24, 1998, as 
revised by Notices of Status Change NSC 01, dated May 7, 1998, NSC 
02, dated May 8, 1998, and NSC 03, dated May 9, 1998; Revision 1, 
dated May 28, 1998; or Revision 2, dated November 26, 1998.
    (1) For airplanes having line numbers 1 through 3072 inclusive 
that have accumulated less than 20,000 total flight hours as of 
October 15, 1998: Inspect at the earlier of the times specified in 
paragraphs (h)(1)(i) and (h)(1)(ii) of this AD.
    (i) Prior to the accumulation of 20,000 total flight hours, or 
within 60 days after November 12, 1999 (the effective date of AD 99-
21-15), whichever occurs later.
    (ii) Within 24 months after November 12, 1999.
    (2) For airplanes having line numbers 3073 and subsequent: 
Inspect prior to the accumulation of 30,000 total flight hours.

Repetitive Intervals

    (i) For Model 737-100, -200, -300, -400, and -500 series 
airplanes: Repeat the inspection required by paragraph (f), (g), or 
(h) of this AD, as applicable, at intervals not to exceed 30,000 
flight hours after initial accomplishment of the applicable 
inspection, until the initial inspection, applicable corrective 
actions, and sleeve installation required by paragraph (k) of this 
AD have been done.

Corrective Actions

    (j) If any discrepancy is found during any inspection required 
by paragraph (f), (g), (h), or (i) of this AD: Before further 
flight, repair the discrepancy in accordance with the Accomplishment 
Instructions of Boeing Alert Service Bulletin 737-28A1120, dated 
April 24, 1998, as revised by Notices of Status Change NSC 01, dated 
May 7, 1998, NSC 02, dated May 8, 1998, and NSC 03, dated May 9, 
1998; Revision 1, dated May 28, 1998; Revision 2, dated November 26, 
1998; or Revision 3, dated April 26, 2001.

New Requirements of This AD

Inspection and Related Investigative and Corrective Actions

    (k) At the applicable time specified by paragraph (k)(1) or 
(k)(2) of this AD: Do a detailed inspection for damage of the sleeve 
and electrical wire of the fuel boost pump; and, before further 
flight, install a new, smaller-diameter sleeve, and do related 
investigative and corrective actions, as applicable; in accordance 
with the Accomplishment Instructions of Boeing Alert Service 
Bulletin 737-28A1263, Revision 1, dated March 19, 2007. Thereafter, 
repeat the detailed inspection at intervals not to exceed 15,000 
flight cycles. Accomplishment of the initial inspection, applicable 
corrective actions, and sleeve installation required by this 
paragraph terminates the requirements of paragraphs (f), (g), (h), 
and (i) of this AD.
    (1) For Model 737-100, -200, -300, -400, and -500 series 
airplanes: Within 120 days after the effective date of this AD, or 
within 5,000 flight hours after the last inspection or repair done 
as required by paragraph (f), (g), (h), or (i), as applicable, of 
this AD, whichever occurs later.
    (2) For Model 737-200C series airplanes: Within 120 days after 
the effective date of this AD, or within 5,000 flight hours after 
the last inspection or repair done in accordance with any version of 
Boeing Alert Service Bulletin 737-28-1120, whichever occurs later.

Inspection Report and Disposition of Damaged Parts

    (l) At the applicable time specified in paragraph (l)(1) or 
(l)(2) of this AD: Submit a report of the findings (both positive 
and negative) of any inspection required by paragraph (k) of this AD 
and send any damaged parts to the manufacturer, as described in 
Boeing Alert Service Bulletin 737-28A1263, Revision 1, dated March 
19, 2007. The report must include the inspection results, a 
description of any discrepancies found, the airplane serial number, 
and the number of landings and flight hours on the airplane. Under 
the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et 
seq.), the Office of Management and Budget (OMB) has approved the 
information collection requirements contained in this AD and has 
assigned OMB Control Number 2120-0056.
    (1) For any inspection done after the effective date of this AD: 
Submit the report within 30 days after the inspection.
    (2) For any inspection done before the effective date of this 
AD: Submit the report within 30 days after the effective date of 
this AD.

[[Page 28601]]

Credit for Actions Done Using Previous Service Information

    (m) Actions accomplished before the effective date of this AD in 
accordance with Boeing Service Bulletin 737-28A1263, dated February 
19, 2007, are considered acceptable for compliance with the 
corresponding actions specified in this AD.

Alternative Methods of Compliance (AMOCs)

    (n)(1) The Manager, Seattle Aircraft Certification Office (ACO), 
FAA, has the authority to approve AMOCs for this AD, if requested in 
accordance with the procedures found in 14 CFR 39.19.
    (2) To request a different method of compliance or a different 
compliance time for this AD, follow the procedures in 14 CFR 39.19. 
Before using any approved AMOC on any airplane to which the AMOC 
applies, notify your appropriate principal inspector (PI) in the FAA 
Flight Standards District Office (FSDO), or lacking a PI, your local 
FSDO.
    (3) AMOCs approved previously in accordance with AD 99-21-15, 
amendment 39-11360, are approved as AMOCs for the corresponding 
provisions of this AD.

Material Incorporated by Reference

    (o) You must use applicable Boeing service bulletins specified 
in Table 1 of this AD to perform the actions that are required by 
this AD, unless the AD specifies otherwise.

                                Table 1.--All Material Incorporated by Reference
----------------------------------------------------------------------------------------------------------------
            Service Bulletin                      Revision level                           Date
----------------------------------------------------------------------------------------------------------------
Boeing Alert Service Bulletin 737-        Original.....................  April 24, 1998.
 28A1120, as revised by Notice of Status
 Change NSC 01, dated May 7, 1998,
 Notice of Status Change NSC 02, dated
 May 8, 1998, and Notice of Status
 Change NSC 03, dated May 9, 1998.
Boeing Alert Service Bulletin 737-        1............................  May 28, 1998.
 28A1120.
Boeing Alert Service Bulletin 737-        2............................  November 26, 1998.
 28A1120.
Boeing Service Bulletin 737-28A1120.....  3............................  April 26, 2001.
Boeing Alert Service Bulletin 737-        1............................  March 19, 2007.
 28A1263.
----------------------------------------------------------------------------------------------------------------

    (1) The Director of the Federal Register approved the 
incorporation by reference of Boeing Alert Service Bulletin 737-
28A1263, Revision 1, dated March 19, 2007; and Boeing Service 
Bulletin 737-28A1120, Revision 3, dated April 26, 2001; in 
accordance with 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) On November 12, 1999 (64 FR 54763, October 8, 1999), the 
Director of the Federal Register approved the incorporation by 
reference of Boeing Alert Service Bulletin 737-28A1120, Revision 2, 
dated November 26, 1998.
    (3) On October 15, 1998 (63 FR 52152, September 30, 1998), the 
Director of the Federal Register approved the incorporation by 
reference of Boeing Alert Service Bulletin 737-28A1120, Revision 1, 
dated May 28, 1998.
    (4) On June 29, 1998 (63 FR 34271, June 24, 1998), the Director 
of the Federal Register approved the incorporation by reference of 
Boeing Alert Service Bulletin 737-28A1120, dated April 24, 1998, as 
revised by Notice of Status Change NSC 01, dated May 7, 1998, Notice 
of Status Change NSC 02, dated May 8, 1998, and Notice of Status 
Change NSC 03, dated May 9, 1998.
    (5) Contact Boeing Commercial Airplanes, P.O. Box 3707, Seattle, 
Washington 98124-2207, for a copy of this service information. You 
may review copies at the FAA, Transport Airplane Directorate, 1601 
Lind Avenue, SW., Renton, Washington; or at the National Archives 
and Records Administration (NARA). For information on the 
availability of this material at NARA, call 202-741-6030, or go to: 
http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Renton, Washington, on May 2, 2007.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. E7-9801 Filed 5-21-07; 8:45 am]
BILLING CODE 4910-13-P