[Federal Register Volume 71, Number 207 (Thursday, October 26, 2006)]
[Proposed Rules]
[Pages 62570-62572]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: E6-17935]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2005-20850; Directorate Identifier 2005-NE-05-AD]
RIN 2120-AA64


Airworthiness Directives; Teledyne Continental Motors GTSIO-520 
Series Reciprocating Engines

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to supersede an existing airworthiness 
directive (AD) for Teledyne Continental Motors (TCM) GTSIO-520 series 
reciprocating engines. That AD currently requires initial and 
repetitive visual inspections of the starter adapter assembly and 
crankshaft gear and unscheduled visual inspections of the starter 
adapter assembly and crankshaft gear due to a rough-running engine. 
That AD also requires replacement of the starter adapter shaft gear 
needle bearing with a certain bushing and installation of a certain TCM 
service kit at the next engine overhaul, or at the next starter adapter 
replacement, whichever occurs first. This proposed AD would require the 
inspection ordered in paragraph (h) of AD 2005-20-04 to be done every 
100 hours time-in-service (TIS), or annually. This proposed AD results 
from an error discovered in AD 2005-20-04. We are proposing this AD to 
prevent failure of the starter adapter assembly and or crankshaft gear, 
resulting in failure of the engine and possible forced landing.

DATES: We must receive any comments on this proposed AD by December 26, 
2006.

ADDRESSES: Use one of the following addresses to comment on this 
proposed AD.
     DOT Docket Web site: Go to http://dms.dot.gov and follow 
the instructions for sending your comments electronically.
     Government-wide rulemaking Web site: Go to http://www.regulations.gov and follow the instructions for sending your 
comments electronically.
     Mail: Docket Management Facility; U.S. Department of 
Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401, 
Washington, DC 20590-0001.
     Fax: (202) 493-2251.
     Hand Delivery: Room PL-401 on the plaza level of the 
Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    You can get the service information identified in this proposed AD 
from Teledyne Continental Motors, Inc., PO Box 90, Mobile, AL 36601; 
telephone (251) 438-3411.

FOR FURTHER INFORMATION CONTACT: Jerry Robinette, Senior Engineer, 
Propulsion, Atlanta Aircraft Certification Office, FAA, Small Airplane 
Directorate, One Crown Center, 1895 Phoenix Blvd., Suite 450, Atlanta, 
GA 30349; telephone: (770) 703-6096, fax: (770) 703-6097.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments regarding this proposal. Send your comments to an address 
listed under ADDRESSES. Include ``Docket No. FAA-2005-20850; 
Directorate Identifier 2005-NE-05-AD'' in the subject line of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of the proposed AD. We will 
consider all comments received by the closing date and may amend the 
proposed AD in light of those comments.
    We will post all comments we receive, without change, to http://dms.dot.gov, including any personal information you provide. We will 
also post a report summarizing each substantive verbal contact with FAA 
personnel concerning this proposed AD. Using the search function of the 
DMS Web site, anyone can find and read the comments in any of our 
dockets, including the name of the individual who sent the comment (or 
signed the comment on behalf of an association, business, labor union, 
etc.). You may review the DOT's complete Privacy Act Statement in the 
Federal Register published on April 11, 2000 (65 FR 19477-78) or you 
may visit http://dms.dot.gov.

Examining the AD Docket

    You may examine the docket that contains the proposal, any comments 
received and any final disposition in person at the DMS Docket Offices 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The Docket Office (telephone (800) 647-5227) is located on 
the plaza level of the Department of Transportation Nassif Building at 
the street address stated in ADDRESSES. Comments will be available in 
the AD docket shortly after the DMS receives them.

Discussion

    On September 20, 2005, the FAA issued AD 2005-20-04, Amendment 39-
14297 (70 FR 56355, September 27, 2005). That AD requires initial and 
repetitive visual inspections of the starter adapter assembly and 
crankshaft gear and unscheduled visual inspections of the starter 
adapter assembly and crankshaft gear due to a rough-running engine. 
That AD also requires replacement of the starter adapter shaft gear 
needle bearing with a certain bushing and installation of a certain TCM 
service kit at the next engine overhaul, or at the next starter

[[Page 62571]]

adapter replacement, whichever occurs first. That AD resulted from six 
service difficulty reports and one fatal accident report that related 
to failed starter adapter assemblies.

Actions Since AD 2005-20-04 Was Issued

    Since we issued that AD, we discovered an error in paragraph (h). 
In that paragraph, we specify an inspection at the next 100-hour or 
annual inspection, whichever occurs first. However, because most of the 
airplanes are privately owned and operate under 14 CFR part 91, they 
are not required to perform 100-hour inspections. This proposed AD 
would correct that error and require the inspections every 100 hours 
TIS, instead of at the next 100-hour inspection.
    Also, since we issued AD 2005-20-04, TCM revised the mandatory 
service bulletin required by this AD. It is now identified as Mandatory 
Service Bulletin (MSB) No. MSB94-4G, dated October 31, 2005, and 
includes a service kit with new, rather than rebuilt parts.

Relevant Service Information

    We have reviewed and approved the technical contents of Teledyne 
Continental Aircraft Engine, MSB94-4G, dated October 31, 2005 that 
provides inspection and replacement procedures for the starter adapter 
assembly and crankshaft gear. That MSB also describes procedures for 
replacement of the needle bearing, part number (P/N) 537721, with P/N 
654472. That MSB also describes procedures for installation of TCM 
service kits EQ6642 (new) or EQ6642R (rebuilt).

Differences Between the Proposed AD and the Service Information

    Although TCM MSB No. MSB94-4G, dated October 31, 2005, applies to 
GIO-550 and GTSIO-520 series reciprocating engines, this proposed AD 
would only apply to GTSIO-520 series reciprocating engines. Also, 
although that MSB mandates in Part 1, that magnetos must be overhauled 
and periodically inspected at specified times, this proposed AD would 
not mandate those actions.

FAA's Determination and Requirements of the Proposed AD

    We have evaluated all pertinent information and identified an 
unsafe condition that is likely to exist or develop on other products 
of this same type design. For that reason, we are proposing this AD, 
which would require:
     Initial and repetitive visual inspections of the starter 
adapter assembly and crankshaft gear, and replacement of components as 
necessary.
     Unscheduled visual inspections of the starter adapter 
assembly and crankshaft gear due to a rough-running engine, and 
replacement of components as necessary.
     Replacement of the starter adapter shaft gear needle 
bearing, P/N 537721 with bushing, P/N 654472.
     Inspection and replacement of components specified in Part 
2 of the MSB as necessary every 100 hours TIS or annually, whichever 
occurs first.
     Inspection of starter adapters with more or less than 400 
hours TIS or unknown TIS.
     Installation of TCM service kit, P/N EQ6642 or P/N 
EQ6642R, at next engine overhaul, or at next starter adapter 
replacement, whichever occurs first.
    The proposed AD would require you to use the service information 
described previously to perform the inspections and replacements.

Costs of Compliance

    We estimate that this AD will affect 4,240 engines installed on 
airplanes of U.S. registry. We also estimate that it would take about 
one work-hour per engine to perform the inspection, about one work-hour 
per engine to perform the proposed bushing installation and about six 
work-hours per engine to install the TCM service kit. The average labor 
rate is $80 per work-hour. We estimate that about 25 percent of the 
engines will require an unscheduled (rough-running engine) inspection 
and about half of the engines will require the bushing and TCM service 
kit. Required bushings would cost about $16 per engine and service kits 
about $800 per engine. Based on these figures, we estimate the total 
cost of the proposed AD to U.S. operators to be $6,393,432.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We have determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that the proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD. See the ADDRESSES section for a location 
to examine the regulatory evaluation.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

    Under the authority delegated to me by the Administrator, the 
Federal Aviation Administration proposes to amend 14 CFR part 39 as 
follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The FAA amends Sec.  39.13 by removing Amendment 39-14297 (70 FR 
56355, September 27, 2005) and by adding a new airworthiness directive, 
Amendment 39-XXXXX, to read as follows:

Teledyne Continental Motors: Docket No. FAA-2005-20850; Directorate 
Identifier 2005-NE-05-AD.

Comments Due Date

    (a) The Federal Aviation Administration (FAA) must receive 
comments on this airworthiness directive (AD) action by December 26, 
2006.

Affected ADs

    (b) This AD supersedes AD 2005-20-04, Amendment 39-14297.

[[Page 62572]]

Applicability

    (c) This AD applies to Teledyne Continental Motors (TCM) GTSIO-
520 series reciprocating engines. These engines are installed on, 
but not limited to, Twin Commander (formerly Aero Commander) model 
685, Cessna model 404, 411 series, and 421 series, British 
Aerospace, Aircraft Group, Scottish Division model B.206 series 2 
and Aeronautica Macchi model AM-3 airplanes.

Unsafe Condition

    (d) This AD results from an error discovered in AD 2005-20-04. 
We are issuing this AD to prevent failure of the starter adapter 
assembly and or crankshaft gear, resulting in failure of the engine 
and possible forced landing.

Compliance

    (e) You are responsible for having the actions required by this 
AD performed within the compliance times specified unless the 
actions have already been done.

Starter Adapter Shaft Gear Needle Bearing Replacement

    (f) If, during an inspection required by paragraph (g), (h), 
(i), or (j) of this AD, you find needle bearing, part number (P/N) 
537721, installed in the crankcase, replace it with a serviceable 
bushing, before reassembling components. Use the bushing 
installation procedure specified in Part 4 of TCM Mandatory Service 
Bulletin (MSB) No. MSB94-4G, dated October 31, 2005.

Unscheduled Inspections for Rough-Running Engines

    (g) For any engine that experiences rough running conditions 
regardless of time-in-service (TIS), do the following:
    (1) Before further flight, perform the inspection procedures 
specified in Part 1 and Part 3 of TCM MSB No. MSB94-4G, dated 
October 31, 2005, and replace components as necessary.
    (2) An engine is considered rough-running if there is a sudden 
increase in the perceived vibration levels that cannot be cleared by 
adjustment of the engine controls; particularly the fuel mixture 
setting. Information on rough running engines can be found in the 
aircraft manufacturer's Airplane Flight Manual, Pilot's Operating 
Handbook, or Aircraft Owners Manual.

100-Hour and Annual Inspections

    (h) For any engine that has been inspected using paragraph (h) 
of AD 2005-20-04 and the 100-hour inspection procedures or 100 hour 
TIS intervals or annual inspection procedures, continue the 
inspections as follows:
    (1) Perform the inspection procedures specified in Part 2 of TCM 
MSB No. MSB94-4G, dated October 31, 2005 and replace components as 
necessary at each 100 hour TIS interval (plus or minus 10 hours TIS) 
or annual inspection, whichever occurs first.
    (2) Thereafter, at each 100 hour TIS interval (plus or minus 10 
hours TIS) perform repetitive inspections and component replacements 
as specified in paragraph (h)(1) of this AD.
    (i) For any engine that has not been inspected using paragraph 
(h) of AD 2005-20-04, within 25 hours TIS or at the annual 
inspection, whichever occurs first, do the following:
    (1) Perform the inspection procedures specified in Part 2 of TCM 
MSB No. MSB94-4G, dated October 31, 2005 and replace components as 
necessary.
    (2) Thereafter, at each 100-hour TIS interval (plus or minus 10 
hours TIS) perform repetitive inspections and component replacements 
as specified in paragraph (i)(1) of this AD.
    (3) If the inspection is performed at more than 100 hour 
intervals, subtract the additional hours from the next scheduled 100 
hour inspection.

Starter Adapters With 400 Hours or More Time-In-Service (TIS) or 
Unknown TIS

    (j) For any starter adapter with 400 hours or more TIS or 
unknown TIS on the effective date of this AD, do the following:
    (1) Within 25 hours TIS, perform the inspection procedures 
specified in Part 3 of TCM MSB No. MSB94-4G, dated October 31, 2005, 
and replace components as necessary.
    (2) Thereafter, at 400-hour TIS intervals, (plus or minus 10 
hours TIS), perform repetitive inspections and component 
replacements specified in Part 3 of TCM MSB No. MSB94-4G, dated 
October 31, 2005, and replace components as necessary.

Starter Adapters With Fewer Than 400 Hours TIS

    (k) For any starter adapter with fewer than 400 hours TIS on the 
effective date of this AD, do the following:
    (1) Upon accumulation of 400 hours TIS, (plus or minus 10 hours 
TIS), perform the inspection procedures specified in Part 3 of TCM 
MSB No. MSB94-4G, dated October 31, 2005, and replace components as 
necessary.
    (2) Thereafter, at 400-hour TIS intervals, (plus or minus 10 
hours TIS), perform repetitive inspections and component 
replacements, as specified in Part 3 of TCM MSB No. MSB94-4G, dated 
October 31, 2005, and replace components as necessary.

Installation of TCM Service Kit, EQ6642 or EQ6642R

    (l) At the next engine overhaul or starter adapter replacement 
after the effective date of this AD, whichever occurs first, do the 
following:
    (1) Install TCM service kit, P/N EQ6642 (new) or EQ6642R 
(rebuilt). Use the service kit installation procedures specified in 
Part 5 of TCM MSB No. MSB94-4G, dated October 31, 2005.
    (2) Continue performing the inspections and component 
replacements specified in paragraphs (g), (h), (i), (j) and (k) of 
this AD.

Prohibition of Special Flight Permits for Rough-Running Engines

    (m) Special flight permits are prohibited for rough-running 
engines described in paragraph (g)(2) of this AD.

Alternative Methods of Compliance (AMOCs)

    (n) The Manager, Atlanta Aircraft Certification Office, FAA, has 
the authority to approve alternative methods of compliance for this 
AD if requested using the procedures found in 14 CFR 39.19.

Related Information

    (o) None.

    Issued in Burlington, Massachusetts, on October 18, 2006.
Thomas A. Boudreau,
Acting Manager, Engine and Propeller Directorate, Aircraft 
Certification Service.
 [FR Doc. E6-17935 Filed 10-25-06; 8:45 am]
BILLING CODE 4910-13-P