[Federal Register Volume 71, Number 136 (Monday, July 17, 2006)]
[Rules and Regulations]
[Pages 40391-40394]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 06-6152]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2006-24432; Directorate Identifier 2005-NM-227-AD; 
Amendment 39-14678; AD 2006-14-07]
RIN 2120-AA64


Airworthiness Directives; Boeing Model 737-100, -200, and -200C 
Series Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is superseding an existing airworthiness directive 
(AD), which applies to certain Boeing Model 737 series airplanes. That 
AD currently requires inspection of the elevator tab inboard hinge 
support structure to detect fatigue cracking and corrective action if 
necessary. That AD also provides an optional terminating action. This 
new AD adds airplanes to the applicability and requires new repetitive 
inspections. For airplanes having elevators with laminated rear spars, 
this new AD requires repetitive inspections for interlaminar corrosion, 
delamination, or disbonding in the rear spar, repetitive inspections 
for cracking in the spar web, and repair including related 
investigative/corrective actions if necessary. For airplanes having 
elevators with solid rear spars, this new AD requires repetitive 
inspections for cracking in the spar web and repair including related 
investigative/corrective actions if necessary. This AD results from 
reports of cracks in the elevator rear spar web at the tab hinge 
bracket locations. We are issuing this AD to detect and correct 
cracking, corrosion, interlaminar corrosion, delamination, and 
disbonding in the elevator rear spar, which may reduce elevator 
stiffness and lead to in-flight vibration. In-flight vibration may lead 
to elevator and horizontal stabilizer damage and reduced 
controllability of the airplane.

DATES: This AD becomes effective August 21, 2006.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in the AD as of August 21, 
2006.

ADDRESSES: You may examine the AD docket on the Internet at http://dms.dot.gov or in person at the Docket Management Facility, U.S. 
Department of Transportation, 400 Seventh Street, SW., Nassif Building, 
Room PL-401, Washington, DC.
    Contact Boeing Commercial Airplanes, P.O. Box 3707, Seattle, 
Washington 98124-2207, for service information identified in this AD.

FOR FURTHER INFORMATION CONTACT: Nancy Marsh, Aerospace Engineer, 
Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office, 
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 
917-6440; fax (425) 917-6590.

SUPPLEMENTARY INFORMATION:

Examining the Docket

    You may examine the airworthiness directive (AD) docket on the 
Internet at http://dms.dot.gov or in person at the Docket Management 
Facility office between 9 a.m. and 5 p.m., Monday through Friday, 
except Federal holidays. The Docket Management Facility office 
(telephone (800) 647-5227) is located on the plaza level of the Nassif 
Building at the street address stated in the ADDRESSES section.

Discussion

    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 to include an AD that supersedes AD 76-11-05 R1, amendment 
39-6234 (54 FR 25709, June 19, 1989). The existing AD applies to 
certain Boeing Model 737 series airplanes. That NPRM was published in 
the Federal Register on April 13, 2006 (71 FR 19144). That NPRM 
proposed to continue to require inspection of the elevator tab inboard 
hinge support structure to detect fatigue cracking and corrective 
action if necessary. That NPRM also proposed to continue to provide an 
optional terminating action for the existing inspections. That NPRM 
proposed to add airplanes to the applicability and to require new 
repetitive inspections. For airplanes having elevators with laminated 
rear spars, that NPRM proposed to require repetitive inspections for 
interlaminar corrosion, delamination, or disbonding

[[Page 40392]]

in the rear spar, repetitive inspections for cracking in the spar web, 
and repair including related investigative/corrective actions if 
necessary. For airplanes having elevators with solid rear spars, that 
NPRM proposed to require repetitive inspections for cracking in the 
spar web and repair including related investigative/corrective actions 
if necessary.

Comments

    We provided the public the opportunity to participate in the 
development of this AD. No comments have been received on the NPRM or 
on the determination of the cost to the public.

Conclusion

    We have carefully reviewed the available data and determined that 
air safety and the public interest require adopting the AD as proposed.

Costs of Compliance

    There are about 1,355 airplanes of the affected design in the 
worldwide fleet. The following table provides the estimated costs for 
U.S. operators to comply with this AD.

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                               Average                        Number of U.S.-
             Action                  Work     labor rate   Cost per airplane    registered        Fleet cost
                                    hours      per hour                          airplanes
----------------------------------------------------------------------------------------------------------------
Inspection, per inspection cycle     10-100          $80  $800-$8,000, per               230  $184,000-$1,840,00
                                                           inspection cycle.                   0, per inspection
                                                                                               cycle.
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We have determined that this AD will not have federalism 
implications under Executive Order 13132. This AD will not have a 
substantial direct effect on the States, on the relationship between 
the national government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866;
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979); and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this AD and placed it in the AD docket. See the ADDRESSES 
section for a location to examine the regulatory evaluation.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The Federal Aviation Administration (FAA) amends Sec.  39.13 by 
removing amendment 39-6234 (54 FR 25709, June 19, 1989) and by adding 
the following new airworthiness directive (AD):

2006-14-07 Boeing: Amendment 39-14678. Docket No. FAA-2006-24432; 
Directorate Identifier 2005-NM-227-AD.

Effective Date

    (a) This AD becomes effective August 21, 2006.

Affected ADs

    (b) This AD supersedes AD 76-11-05 R1.

Applicability

    (c) This AD applies to Boeing Model 737-100, -200, and -200C 
series airplanes, certificated in any category; as identified in 
Boeing Alert Service Bulletin 737-55A1078, dated October 27, 2005.

Unsafe Condition

    (d) This AD results from reports of cracks in the elevator rear 
spar web at the tab hinge bracket locations. We are issuing this AD 
to detect and correct cracking, corrosion, interlaminar corrosion, 
delamination, and disbonding in the elevator rear spar, which may 
reduce elevator stiffness and lead to in-flight vibration. In-flight 
vibration may lead to elevator and horizontal stabilizer damage and 
reduced controllability of the airplane.

Compliance

    (e) You are responsible for having the actions required by this 
AD performed within the compliance times specified, unless the 
actions have already been done.

Restatement of Certain Requirements of AD 76-11-05 R1

    (f) For Model 737-100, -200, and -200C series airplanes, line 
number 001 through 491 inclusive: Within the next 300 hours time-in-
service after July 24, 1989 (the effective date of AD 76-11-05 R1), 
unless accomplished within the last 700 hours time-in-service, and 
at intervals thereafter not to exceed 1,000 hours time-in-service, 
conduct the inspection required by paragraph (g) of this AD. 
Accomplishing the initial inspections specified in paragraph (j) of 
this AD terminates the requirements of this paragraph.
    (g) For Model 737-100, -200, and -200C series airplanes, line 
number 001 through 491 inclusive: At the times specified in 
paragraph (f) of this AD, inspect for excessive deflection of the 
elevator tab, right and left hand, in accordance with the inspection 
procedures specified in Section III, Part I, paragraphs C. and D., 
of Boeing Alert Service Bulletin 737-55-A1020, Revision 1, dated 
August 20, 1976; Revision 2, dated February 11, 1977; or 737-
55A1020, Revision 3, dated December 22, 1988. If the elevator tab-
to-elevator relative deflection exceeds 1/10 inch, prior to further 
flight, modify the elevator in accordance with paragraph (h) of this 
AD. Accomplishing the initial inspections specified in paragraph (j) 
of this AD terminates the requirements of this paragraph.

[[Page 40393]]

    (h) For Model 737-100, -200, and -200C series airplanes, line 
number 001 through 491 inclusive: Installation of one of the 
modifications specified in Boeing Alert Service Bulletin 737-55-
A1020, Revision 1, dated August 20, 1976; 737-55-A1020, Revision 2, 
dated February 11, 1977; or 737-55A1020, Revision 3, dated December 
22, 1988; Section III, Part II, including installation of the bolt 
retainer clips or the preventive modification specified in Boeing 
Service Bulletin 737-55-1022, Section III, Part II, dated April 15, 
1977; is considered terminating action for the inspection 
requirements of paragraph (g) of this AD.

New Requirements of This AD

Determine Elevator Group Number or Elevator Configuration Number

    (i) Within 1,000 flight hours or 750 flight cycles after the 
effective date of this AD, whichever occurs first, determine the 
elevator group number or the elevator configuration number in 
accordance with Appendix A of Boeing Alert Service Bulletin 737-
55A1078, dated October 27, 2005.

Initial and Repetitive Inspections

    (j) At the applicable time specified in Tables 2 and 3 of 
paragraph 1.E. ``Compliance'' of Boeing Alert Service Bulletin 737-
55A1078, dated October 27, 2005, except where the alert service 
bulletin specifies a compliance time from the release date of the 
alert service bulletin, this AD requires the compliance time after 
the effective date of this AD: Do the applicable initial detailed 
and special detailed inspections for interlaminar corrosion, 
cracking, delamination, or disbonding in the rear spar by doing all 
the applicable actions specified in Parts I, II, and III of the 
Accomplishment Instructions of Boeing Alert Service Bulletin 737-
55A1078, dated October 27, 2005; except where step 3. of Part III of 
the alert service bulletin specifies to do a special detailed 
inspection for spar interlaminar corrosion as given in Figure 3, 
this AD requires all actions specified in Figure 3 to be done (a 
detailed inspection for interlaminar corrosion and disbonding and a 
special detailed inspection for interlaminar corrosion and 
delamination). Doing the initial inspections terminates the 
requirements of paragraphs (f) and (g) of this AD.
    (k) Repeat the inspections specified in paragraph (j) of this AD 
at the applicable time specified in Tables 4 and 5 of paragraph 1.E. 
``Compliance'' of Boeing Alert Service Bulletin 737-55A1078, dated 
October 27, 2005; except where Table B.4 in Appendix B of the alert 
service bulletin specifies compliance times in flight hours or 
flight cycles, this AD requires the actions specified in Table B.4 
be done at the earlier of the compliance times in flight hours or 
flight cycles.

Corrective Actions

    (l) If any interlaminar corrosion, cracking, delamination, or 
disbonding is found during any inspection required by this AD: 
Before further flight, use Appendix C of Boeing Alert Service 
Bulletin 737-55A1078, dated October 27, 2005, to determine the 
permitted repairs, and do the applicable repair, including related 
investigative and corrective actions, by doing all the applicable 
actions specified in Parts IV through VIII (Interim Repairs) and 
Part IX (Time-limited Repair) of the Accomplishment Instructions of 
the alert service bulletin, except as provided by paragraphs (n) and 
(o) of this AD.
    (m) If the time-limited repair specified in Part IX of the 
Accomplishment Instructions of Boeing Alert Service Bulletin 737-
55A1078, dated October 27, 2005, is done: At the time specified in 
Table 6 of paragraph 1.E. ``Compliance'' of the alert service 
bulletin, do the applicable repair, including related investigative 
and corrective actions, by doing all the applicable actions 
specified in Parts IV through VI (Interim Repairs) of the alert 
service bulletin. Thereafter, do the repetitive inspections 
specified in paragraph (k) of this AD.
    (n) Where Boeing Alert Service Bulletin 737-55A1078, dated 
October 27, 2005, specifies to contact the manufacturer for 
appropriate action for the inspar rib replacement or for more 
instructions if any crack is outside the limit specified in the 
service bulletin: Before further flight, repair in accordance with a 
method approved by the Manager, Seattle Aircraft Certification 
Office (ACO), FAA; or using a method approved in accordance with 
paragraph (p) of this AD.
    (o) Where step 3.a. of Part III of the Accomplishment 
Instructions of Boeing Alert Service Bulletin 737-55A1078, dated 
October 27, 2005, specifies that if interlaminar corrosion is found, 
spar replacement is required, this AD requires spar replacement if 
interlaminar corrosion, delamination, or disbonding is found. Where 
step 3.C. of Appendix C of the alert service bulletin specifies that 
for laminated spars that have interlaminar corrosion, only repair 
options B, C, and D are permitted, this AD specifies that for 
laminated spars that have interlaminar corrosion, delamination, or 
disbonding, only repair options B, C, and D are permitted.

Alternative Methods of Compliance (AMOCs)

    (p)(1) The Manager, ACO, FAA, has the authority to approve AMOCs 
for this AD, if requested in accordance with the procedures found in 
14 CFR 39.19.
    (2) Before using any AMOC approved in accordance with Sec.  
39.19 on any airplane to which the AMOC applies, notify the 
appropriate principal inspector in the FAA Flight Standards 
Certificate Holding District Office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair required by this AD, if it is approved by an 
Authorized Representative for the Boeing Commercial Airplanes 
Delegation Option Authorization Organization who has been authorized 
by the Manager, Seattle ACO, to make those findings. For a repair 
method to be approved, the repair must meet the certification basis 
of the airplane, and the approval must specifically refer to this 
AD.
    (4) Accomplishing the Interim Repair Option C or D specified in 
the Accomplishment Instructions of Boeing Alert Service Bulletin 
737-55A1078, dated October 27, 2005, is an AMOC for the structural 
modification requirements specified in paragraph A. of AD 90-06-02, 
amendment 39-6489, that are done in accordance with Boeing Alert 
Service Bulletins 737-55-A1020 or 737-55A1020, or Boeing Service 
Bulletin 737-55-1022 only. All provisions of AD 90-06-02 that do not 
specifically reference these service bulletins remain fully 
applicable and must be complied with.
    (5) AMOCs approved previously in accordance with AD 76-11-05 R1, 
are approved as AMOCs for the corresponding provisions of paragraphs 
(f) through (h) of this AD.

Material Incorporated by Reference

    (q) You must use the applicable service bulletins listed in 
Table 1 of this AD to perform the actions that are required by this 
AD, unless the AD specifies otherwise. The Director of the Federal 
Register approved the incorporation by reference of these documents 
in accordance with 5 U.S.C. 552(a) and 1 CFR part 51.

                                  Table 1.--Material Incorporated by Reference
----------------------------------------------------------------------------------------------------------------
            Service Bulletin                       Revision level                           Date
----------------------------------------------------------------------------------------------------------------
Boeing Alert Service Bulletin 737-        1...............................  August 20, 1976.
 55A1020.
Boeing Alert Service Bulletin 737-        2...............................  February 11, 1977.
 55A1020.
Boeing Alert Service Bulletin 737-        3...............................  December 22, 1988.
 55A1020.
Boeing Alert Service Bulletin 737-        Original........................  October 27, 2005.
 55A1078.
Boeing Service Bulletin 737-55-1022.....  Original........................  April 15, 1977.
----------------------------------------------------------------------------------------------------------------

    Boeing Alert Service Bulletin 737-55-A1020, Revision 1, dated 
August 20, 1976, contains the following effective pages:

[[Page 40394]]



----------------------------------------------------------------------------------------------------------------
                Page No.                    Revision level shown on page             Date shown on page
----------------------------------------------------------------------------------------------------------------
1, 11-27................................  1...............................  August 20, 1976.
2-10....................................  Original........................  May 20, 1976.
----------------------------------------------------------------------------------------------------------------

    Boeing Alert Service Bulletin 737-55-A1020, Revision 2, dated 
February 11, 1977, contains the following effective pages:

----------------------------------------------------------------------------------------------------------------
                Page No.                    Revision level shown on page             Date shown on page
----------------------------------------------------------------------------------------------------------------
1, 3, 6, 10-12, 14, 16, 25..............  2...............................  February 11, 1977.
2, 4, 5, 7-9............................  Original........................  May 20, 1976.
13, 15, 17-24, 26, 27...................  1...............................  August 20, 1976.
----------------------------------------------------------------------------------------------------------------

    Contact Boeing Commercial Airplanes, P.O. Box 3707, Seattle, 
Washington 98124-2207, for a copy of this service information. You 
may review copies at the Docket Management Facility, U.S. Department 
of Transportation, 400 Seventh Street, SW., Room PL-401, Nassif 
Building, Washington, DC; on the Internet at http://dms.dot.gov; or 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at the NARA, call 
(202) 741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

    Issued in Renton, Washington, on July 3, 2006.
Kalene C. Yanamura,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 06-6152 Filed 7-14-06; 8:45 am]
BILLING CODE 4910-13-P