[Federal Register Volume 71, Number 111 (Friday, June 9, 2006)]
[Rules and Regulations]
[Pages 33402-33411]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: E6-9059]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Pipeline and Hazardous Materials Safety Administration

49 CFR Parts 192, 193, and 195

[Docket No. PHMSA-05-21253; Amdt. Nos. 192-103, 193-19, and 195-86]
RIN 2137-AD68


Pipeline Safety: Update of Regulatory References to Technical 
Standards

AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), 
DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: This final rule updates the pipeline safety regulations to 
incorporate by reference all or parts of new editions of voluntary 
consensus technical standards to enable pipeline operators to utilize 
current technology, materials, and practices.

DATES: This final rule takes effect on July 10, 2006. The incorporation 
by reference of publications listed in the rule is approved by the 
Director of the Federal Register as of July 10, 2006.

FOR FURTHER INFORMATION CONTACT: Richard D. Huriaux, Director, 
Technical Standards at (202) 366-4565, by fax at (202) 366-4566, or by 
e-mail at [email protected]. Copies of this document or other 
material in the docket can be reviewed by accessing the Docket 
Management System's home page at http://dms.dot.gov. General 
information on the pipeline safety program is available at PHMSA's Web 
site at http://ops.dot.gov.

SUPPLEMENTARY INFORMATION:

I. Background

    The National Technology Transfer and Advancement Act of 1995 (Pub. 
L. 104-113) directs Federal agencies to use voluntary consensus 
standards in lieu of government-written standards whenever possible. 
Voluntary consensus standards are standards developed or adopted by 
voluntary bodies that develop, establish, or coordinate technical 
standards using agreed upon procedures.
    PHMSA participates in more than 25 national voluntary consensus 
standards committees. PHMSA's policy is to adopt voluntary consensus 
standards when they are applicable to pipeline design, construction, 
maintenance, inspection, and repair. In recent years, PHMSA has adopted 
dozens of new and revised voluntary consensus standards into its gas 
pipeline (49 CFR part 192), hazardous liquid pipeline (49 CFR part 
195), and liquefied natural gas (LNG) (49 CFR part 193) regulations.
    Parts 192, 193, and 195 incorporate by reference all or parts of 
more than 60 standards and specifications developed and published by 
technical organizations, including the American Petroleum Institute, 
American Gas Association, American Society of Mechanical Engineers, 
American Society for Testing and Materials, Manufacturers 
Standardization Society of the Valve and Fittings Industry, National 
Fire Protection Association, Plastics Pipe Institute, and Pipeline 
Research Council International. These organizations update and revise 
their published standards every 3 to 5 years, to reflect modern 
technology and best technical practices. PHMSA has reviewed the revised 
voluntary consensus standards to be incorporated in whole or in part in 
49 CFR parts 192, 193, and 195.
    This final rule updates the Federal pipeline safety regulations to 
incorporate by reference all or parts of recent editions of the 
voluntary consensus technical standards that are currently referenced 
in the Federal pipeline safety regulations. It updates 38 standards in 
49 CFR part 192, Transportation of Natural and Other Gas by Pipeline: 
Minimum Federal Safety Standards, 49 CFR part 193, Liquefied Natural 
Gas Facilities: Federal Safety Standards, and 49 CFR part 195, 
Transportation of Hazardous Liquids by Pipeline. This update enables 
pipeline operators to use current technology, materials, and practices. 
The incorporation of the most recent editions of standards improves 
clarity, consistency, and accuracy, and reduces unnecessary burdens on 
the regulated community.
    Previous updates of the regulations to incorporate revised 
standards were issued on May 24, 1996 (61 FR 26121), June 6, 1996 (61 
FR 2877), February 17, 1998 (63 FR 7721), and June 14, 2004

[[Page 33403]]

(69 FR 32886). PHMSA intends to issue periodic updates of referenced 
standards to ensure that the pipeline safety regulations reflect 
current practices and to improve compliance by the pipeline industry 
with safety standards.

II. Notice of Proposed Rulemaking

    On July 18, 2005, PHMSA published a Notice of Proposed Rulemaking 
(NPRM) to incorporate by reference 39 new and/or reaffirmed editions of 
standards into the Federal pipeline safety regulations. All but one of 
the new editions is incorporated by reference in this final rule.
    PHMSA has chosen not to update the regulatory references found in 
the 2004 edition of the American Society for Testing and Materials' 
(ASTM) D2513, Standard Specification for Thermoplastic Gas Pressure 
Pipe, Tubing, and Fittings. We believe that a number of important 
issues need to be fully addressed by the ASTM Committee F-17 before we 
adopt any new editions of ASTM D2513. Among these are the issues of 
rework, regrind, marking, increase in design factor, and requirements 
for new materials. The gas pipeline safety regulations therefore 
continue to reference standards found in ASTM D2513 (1999 edition) and 
ASTM D2517 (2000 edition) for plastic pipe and fittings.
    This final rule accepts the following new editions of currently 
referenced standards for incorporation by reference (IBR) in parts 192, 
193, and 195. The list is organized by the standards developing 
organization responsible for the standard and shows each section of the 
regulations referencing the standard.
American Gas Association (AGA):
 Purging Principles and Practices (3rd edition, 2001)
    Replaces current IBR: 1975 edition
    Referenced by 49 CFR 193.2513; 193.2517; 193.2615
American Petroleum Institute (API):
 API Specification 5L ``Specification for Line Pipe'' (43rd 
edition and errata, 2004)
    Replaces current IBR: 42nd edition, 2000
    Referenced by 49 CFR 192.55(e); 192.113; Item I, Appendix B to part 
192; 195.106(b)(1)(i); 195.106(e)
 API Specification 5L1 ``Recommended Practice for Railroad 
Transportation of Line Pipe'' (6th edition, 2002)
    Replaces current IBR: 4th edition, 1990
    Referenced by 49 CFR 192.65(a)
 API Specification 6D ``Pipeline Valves'' (22nd edition, 
January 2002)
    Replaces current IBR: 21st edition, 1994
    Referenced by 49 CFR 192.145(a); 195.116(d)
 API 620 ``Design and Construction of Large, Welded, Low-
Pressure Storage Tanks'' (10th edition, 2002 including Addendum 1)
    Replaces current IBR: 9th edition, 1996
    Referenced by 49 CFR 195.132(b)(2); 195.205(b)(2); 195.264(b)(1); 
195.264(e)(3); 195.307(b)
 API 1130 ``Computational Pipeline Monitoring for Liquid 
Pipelines'' (2nd edition, 2002)
    Replaces current IBR: 1st edition, 1995
    Referenced by 49 CFR 195.134; 195.444
 API 2000 ``Venting Atmospheric and Low-Pressure Storage 
Tanks'' (5th edition, April 1998)
    Replaces current IBR: 4th edition, 1992
    Referenced by 49 CFR 195.264(e)(2); 195.264(e)(3)
 API 2510 ``Design and Construction of LPG Installations'' (8th 
edition, 2001)
    Replaces current IBR: 7th edition, 1995
    Referenced by 49 CFR 195.132(b)(3); 195.205(b)(3); 195.264(b)(2); 
195.264(e)(4); 195.307(e); 195.428(c); 195.432(c)
American Society of Civil Engineers (ASCE):
 SEI/ASCE 7-02 ``Minimum Design Loads for Buildings and Other 
Structures'' (2002 edition)
    Replaces current IBR: 1995 edition
    Referenced by 49 CFR 193.2067
American Society for Testing and Materials (ASTM):
 ASTM A53/A53M-04a (2004) ``Standard Specification for Pipe, 
Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless''
    Replaces current IBR: 1999 edition
    Referenced by 49 CFR 192.113; Item I, Appendix B to part 192; 
195.106(e)
 ASTM A106/A106M-04b (2004) ``Standard Specification for 
Seamless Carbon Steel Pipe for High-Temperature Service''
    Replaces current IBR: 1999 edition
    Referenced by 49 CFR 192.113; Item I, Appendix B to part 192; 
195.106(e)
 ASTM A333/A333M-05 (2005) ``Standard Specification for 
Seamless and Welded Steel Pipe for Low-Temperature Service''
    Replaces current IBR: 1999 edition
    Referenced by 49 CFR 192.113; Item I, Appendix B to part 192; 
195.106(e)
 ASTM A372/A372M-03 (2003) ``Standard Specification for Carbon 
and Alloy Steel Forgings for Thin-Walled Pressure Vessels''
    Replaces current IBR: 1999 edition
    Referenced by 49 CFR 192.177(b)(1)
 ASTM A381-96 (Reapproved 2001) ``Standard Specification for 
Metal-Arc-Welded Steel Pipe for Use With High-Pressure Transmission 
Systems''
    Replaces current IBR: 1996 edition
    Referenced by 49 CFR 192.113; Item I, Appendix B to part 192; 
195.106(e)
 ASTM A671-04 (2004) ``Standard Specification for Electric-
Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures''
    Replaces current IBR: 1996 edition
    Referenced by 49 CFR 192.113; Item I, Appendix B to part 192; 
195.106(e)
 ASTM A672-96 (Reapproved 2001) ``Standard Specification for 
Electric-Fusion-Welded Steel Pipe for High-Pressure Service at Moderate 
Temperatures''
    Replaces current IBR: 1996 edition
    Referenced by 49 CFR 192.113; Item I, Appendix B to part 192; 
195.106(e)
 ASTM A691-98 (Reapproved 2002) ``Standard Specification for 
Carbon and Alloy Steel Pipe, Electric-Fusion-Welded for High-Pressure 
Service at High Temperatures''
    Replaces current IBR: 1998 edition
    Referenced by 49 CFR 192.113; Item I, Appendix B to part 192; 
195.106(e)
 ASTM D638-03 ``Standard Test Method for Tensile Properties of 
Plastics''
    Replaces current IBR: 1999 edition
    Referenced by 49 CFR 192.283(a)(3); 192.283(b)(1)
ASME International (ASME):
 ASME B16.5-2003 (October 2004) ``Pipe Flanges and Flanged 
Fittings''
    Replaces current IBR: 1996 edition
    Referenced by 49 CFR 192.147(a); 192.279
 ASME B31G-1991 (Reaffirmed; 2004) ``Manual for Determining the 
Remaining Strength of Corroded Pipelines''
    Replaces current IBR: 1991 edition
    Referenced by 49 CFR 192.485(c); 192.933(a); 195.452(h)(4)(i)(B); 
195.452(h)(4)(iii)(D)
 ASME B16.9-2003 (February 2004) ``Factory-Made Wrought Steel 
Butt Welding Fittings''
    Replaces current IBR: 1993 edition
    Referenced by 49 CFR 195.118(a)
 ASME B31.4-2002 (October 2002) ``Pipeline Transportation 
Systems for

[[Page 33404]]

Liquid Hydrocarbons and Other Liquids''
    Replaces current IBR: 1998 edition
    Referenced by 49 CFR 195.452(h)(4)(i)
 ASME B31.8-2003 (February 2004) ``Gas Transmission and 
Distribution Piping Systems''
    Replaces current IBR: 1995 edition
    Referenced by 49 CFR 192.619(a)(1)(i); 195.5(a)(1)(i); 
195.406(a)(1)(i)
 ASME B31.8S-2004 ``Supplement to B31.8 on Managing System 
Integrity of Gas Pipelines''
    Replaces current IBR: 2002 edition
    Referenced by 49 CFR 192.903(c); 192.907(b); 192.911 Introductory 
text; 192.911(i); 192.911(k); 192.911(l); 192.911(m); 192.913(a) 
Introductory text; 192.913(b)(1); 192.917(a) Introductory text; 
192.917(b); 192.917(c); 192.917(e)(1); 192.917(e)(4); 192.921(a)(1); 
192.923(b)(2); 192.923(b)(3); 192.925(b) Introductory text; 
192.925(b)(1); 192.925(b)(2); 192.925(b)(3); 192.925(b)(4); 192.927(b); 
192.927(c)(1)(i); 192.929(b)(1); 192.929(b)(2); 192.933(a); 
192.933(d)(1); 192.933(d)(1)(i); 192.935(a); 192.935(b)(1)(iv); 
192.937(c)(1); 192.939(a)(1)(i); 192.939(a)(1)(ii); 192.939(a)(3); 
192.945(a)
 ASME Boiler and Pressure Vessel Code, Section I, ``Rules for 
Construction of Power Boilers'' (2004 edition, including addenda 
through July 1, 2005)
    Replaces current IBR: 1998 edition
    Referenced by 49 CFR 192.153(a)
 ASME Boiler and Pressure Vessel Code, Section VIII, Division 
1, ``Rules for Construction of Pressure Vessels'' (2004 edition, 
including addenda through July 1, 2005)
    Replaces current IBR: 1998 edition as referenced in Sec.  193.2321; 
2001 edition for all other references
    Referenced by 49 CFR 192.153(a); 192.153(b); 192.153(d); 
192.165(b)(3); 193.2321; 195.124; 195.307(e)
 ASME Boiler and Pressure Vessel Code, Section VIII, Division 
2, ``Rules for Construction of Pressure Vessels--Alternative Rules'' 
(2004 edition, including addenda through July 1, 2005)
    Replaces current IBR: 1998 edition as referenced in Sec.  193.2321; 
2001 edition for all other references
    Referenced by 49 CFR 192.153(b); 192.165(b)(3); 193.2321; 
195.307(e)
 ASME Boiler and Pressure Vessel Code, Section IX, ``Welding 
and Brazing Qualifications'' (2004 edition, including addenda through 
July 1, 2005)
    Replaces current IBR: 2001 edition
    Referenced by 49 CFR 192.227(a); Item II, Appendix B to part 192; 
195.222
Gas Technology Institute (GTI):
 GTI-04/0049 (April 2004) ``LNG Vapor Dispersion Prediction 
with the DEGADIS 2.1 Dense Gas Dispersion Model for LNG Vapor 
Dispersion''
    Replaces current IBR: April 1988-July 1990 edition
    Referenced by 49 CFR 193.2059
Manufacturers Standardization Society of the Valve and Fittings 
Industry, Inc. (MSS):
 MSS SP-75-2004 ``Specification for High Test Wrought Butt 
Welding Fittings''
    Replaces current IBR: 1993
    Referenced by 49 CFR 195.118(a)
 MSS SP-44-1996 (Reaffirmed; 2001) ``Steel Pipe Line Flanges''
    Replaces current IBR: 1996
    Referenced by 49 CFR 192.147(a)
NACE International (NACE):
 NACE Standard RP0169-2002 ``Control of External Corrosion on 
Underground or Submerged Metallic Piping Systems''
    Replaces current IBR: 1996
    Referenced by 49 CFR 195.571; 195.573
National Fire Protection Association (NFPA):
 NFPA 30 (2003) ``Flammable and Combustible Liquids Code''
    Replaces current IBR: 1996
    Referenced by 49 CFR 192.735(b); 195.264(b)(1)
 NFPA 58 (2004) ``Liquefied Petroleum Gas Code (LP-Gas Code)''
    Replaces current IBR: 1998
    Referenced by 49 CFR 192.11(a); 192.11(b); 192.11(c)
 NFPA 59 (2004) ``Utility LP-Gas Plant Code''
    Replaces current IBR: 1998
    Referenced by 49 CFR 192.11(a); 192.11(b); 192.11(c)
 NFPA 70 (2005) ``National Electrical Code''
    Replaces current IBR: 1996
    Referenced by 49 CFR 192.163(e); 192.189(c)
Plastics Pipe Institute, Inc. (PPI):
 PPI TR-3/2004 (2004) ``Policies and Procedures for Developing 
Hydrostatic Design Basis (HDB), Pressure Design Basis (PDB), Strength 
Design Basis (SDB), and Minimum Required Strength (MRS) Ratings for 
Thermoplastic Piping Materials or Pipe''
    Replaces current IBR: 2000
    Referenced by 49 CFR 192.121

III. Comments on Proposed Rule

    PHMSA received only two comments in response to the proposed rule. 
First, the Pipeline Standards-Developing Organizations Coordinating 
Committee (PSDOCC) suggested that the most current addenda be included 
for selected API tank standards as follows:

     API Standard 620--include Addendum 1
     API Standard 650--include Addenda 1-3
     API Standard 653--include Addendum 1

    These addenda are an integral part of the new editions of each 
standard. Therefore, we will accept this suggestion and will explicitly 
cite the addenda in the regulation.
    Secondly, comments by the National Fire Protection Association 
(NFPA) are fully supportive of the incorporation by reference of the 
proposed standards. They suggest only minor changes when citing the 
National Electric Code (NEC). We agree and will cite the NEC as NFPA 70 
(2005) in this final rule.

IV. Advisory Committee Recommendations

    The Technical Pipeline Safety Standards Committee (TPSSC) and the 
Technical Hazardous Liquid Pipeline Safety Standards Committee 
(THLPSSC) at their December 14, 2005 meeting considered a July 18, 2005 
proposal to update regulatory references to technical standards.
    The TPSSC and THLPSSC have been established by statute to evaluate 
proposed pipeline safety regulations. Each committee has an authorized 
membership of 15 individuals with membership evenly divided between the 
government, industry, and the public. Each member of these committees 
is qualified to consider the technical feasibility, reasonableness, 
cost-effectiveness, and practicability of proposed pipeline safety 
regulations.
    The proposal was unanimously accepted by all members of the 
THLPSSC. The comments of the TPSSC supported the proposal and generally 
were consistent with written comments filed by other commenters 
discussed above.

V. Editorial Changes

     The definition at Sec.  192.121 on the strength (``S'') of 
plastic pipe is updated to include the current reference to part D.2. 
of PPI TR-3/2004 instead of part E of TR-3/2000.
     The reference at Sec.  192.619(a)(1)(i) to section N5.0 of 
Appendix N of ASME B31.8 is updated to refer to section N5.

[[Page 33405]]

     The phrase, ``HIGH CONSEQUENCE AREAS'', that appears after 
Sec.  192.755 is deleted. This phrase was a typographical error.
     The title to subpart O of part 192 is changed to read, 
``Gas Transmission Pipeline Integrity Management''. This new title 
accurately reflects that the subpart applies only to gas transmission 
pipelines.
     The standards reference for wind load data in Sec.  
193.2067(b)(1) or LNG containers with less than 70,000 gallons is 
updated to refer to ASCE/SEI 7-02, the current designation, rather than 
to ASCE 7.
     The standards reference for valve shell and seat testing 
in Sec.  195.116(d) is corrected to refer to section 10 of API 
Specification 6D, the current designation, rather than to section 5.
     The NPRM proposed to incorporate by reference NFPA 30 
(2003), the new edition of the Flammable and Combustible Liquids Code. 
The section numbering in the 2003 edition differs from that in the 1996 
edition. This requires updates to the section references in the 
hazardous liquid pipeline safety regulations. Therefore, Sec.  
195.264(b)(1)(i) should cite section 4.3.2.3.2 of NFPA 30 (2003) 
instead of section 2-3.4.3 of NPFA 30 (1996). Similarly, Sec.  
195.264(b)(1)(ii) should cite section 4.3.2.3.1 of NFPA 30 (2003) 
instead of section 2-3.4.2 of NFPA 30 (1996). We have made these 
editorial changes in the final rule.
     The NPRM proposed to incorporate by reference API Standard 
2510 (2001), the new edition of the standard for Design and 
Construction of LPG Installations. The section numbering in the 2001 
edition differs from that in the 1995 edition. This requires 
corrections to the section references in the hazardous liquid pipeline 
safety regulations. Therefore, Sec.  195.264(b)(2) should cite sections 
5 and 11 in API Standard 2510 (2001) instead of sections 3 and 9 and 
Sec.  195.264(e)(4) should cite sections 7 and 11 instead of sections 5 
and 9. We have made these editorial changes in the final rule.
     The NPRM proposed to incorporate by reference API 620 
(2002), the new edition of the standard for Design and Construction of 
Large, Welded, Low-Pressure Storage Tanks. The section numbering in the 
2002 edition differs from that in the previous edition. This requires 
updates to the section references in the hazardous liquid pipeline 
safety regulations. Therefore, Sec.  195.264(e)(3) should cite section 
9 of API 620 instead of section 7. Similarly, Sec.  195.307(b) should 
cite section 7.18 instead of section 5.18. We have made these editorial 
changes in the final rule.
     The NPRM proposed to incorporate by reference NACE 
Standard RP-0169 (2002), the new edition of the standard for Control of 
External Corrosion on Underground or Submerged Metallic Piping Systems. 
The current text of Sec. Sec.  195.571 and 195.573(a)(2) refers to NACE 
Standard RP0169-96. We have corrected these citations to the correct 
form, which is ``NACE Standard RP-0169.''

VI. Rulemaking Analyses

Privacy Act

    Anyone is able to search the electronic database for all comments 
and documents received into any of our dockets by the name of the 
individual submitting the comment (or signing the comment, if submitted 
on behalf of an association, business, labor union, etc.). You may 
review DOT's complete Privacy Act Statement in the Federal Register 
published on April 11, 2000 (65 FR 19477) or you may visit the online 
Docket Management System at: http://dms.dot.gov.

Executive Order 12866

    This final rule is not a significant regulatory action under 
section 3(f) of Executive Order 12866 (58 FR 51735) and, therefore, was 
not subject to review by the Office of Management and Budget (OMB). 
This rule is not significant under the Regulatory Policies and 
Procedures of the Department of Transportation (44 FR 11034).

Executive Order 13132

    This rule has been analyzed in accordance with the principles and 
criteria contained in Executive Order 13132 (``Federalism''). This 
final rule does not:
    (1) Have substantial direct effect on the states, the relationship 
between the national government and the states, or the distribution of 
power and responsibilities among the various levels of government;
    (2) Impose substantial direct compliance costs on state and local 
governments; or
    (3) Preempt state law.
    Therefore, the consultation and funding requirements of Executive 
Order 13132 do not apply.

Executive Order 13084

    This final rule has been analyzed in accordance with the principles 
and criteria contained in Executive Order 13084, Consultation and 
Coordination with Indian Tribal Governments. Because this rule will not 
significantly or uniquely affect the Indian tribal governments, the 
funding and consultation requirements of Executive Order 13084 do not 
apply.

Executive Order 13211

    PHMSA has determined this final rule is not a ``significant energy 
action'' under Executive Order 13211. It also is not a significant 
regulatory action under Executive Order 12866 and is not likely to have 
significant adverse effect on the supply, distribution, or use of 
energy. Further, this final rule has not been designated by the 
Administrator of the Office of Information and Regulatory Affairs as a 
significant energy action.

Regulatory Flexibility Act

    This final rule will not impose additional requirements on pipeline 
operators, including small entities that operate regulated pipelines. 
Rather, the final rule only incorporates the most recent editions of 
voluntary consensus standards that represent the current best practice 
in pipeline technology. Incorporating the most recent editions of these 
standards does not impose additional costs on small or large gas 
pipelines, hazardous liquid pipelines, or liquefied natural gas 
companies, and may reduce costs by contributing to even safer pipeline 
operations. Based on the facts available about the expected impact of 
this rulemaking, I certify, under section 605 of the Regulatory 
Flexibility Act (5 U.S.C. 605), that this rulemaking will not have a 
significant economic impact on a substantial number of small entities.

National Environmental Policy Act

    We have analyzed the final rule changes for purposes of the 
National Environmental Policy Act (42 U.S.C. 4321 et seq.). Because the 
adoption of the latest standards moves pipeline construction, 
operations, and maintenance toward current best practices, we have 
determined that the changes will not significantly affect the quality 
of the human environment.

Paperwork Reduction Act

    This final rule does not impose any new or revised information 
collection requirements.

Unfunded Mandates Reform Act of 1995

    This final rule does not impose unfunded mandates under the 
Unfunded Mandates Reform Act of 1995. It does not result in costs of 
$100 million or more to State, local, or tribal governments, in the 
aggregate, or to the private sector, and is the least burdensome 
alternative that achieves the objective of the final rule.

[[Page 33406]]

List of Subjects

49 CFR Part 192

    Incorporation by reference, Natural gas, Pipeline safety.

49 CFR Part 193

    Incorporation by reference, Liquefied natural gas, Pipeline safety.

49 CFR Part 195

    Anhydrous ammonia, Carbon dioxide, Incorporation by reference, 
Petroleum, Pipeline safety.

0
In consideration of the foregoing, PHMSA amends 49 CFR parts 192, 193, 
and 195 as follows:

PART 192--[AMENDED]

0
1. The authority citation for part 192 continues to read as follows:

    Authority: 49 U.S.C. 5103, 60102, 60104, 60108, 60109, 60110, 
60113, and 60118; and 49 CFR 1.53.


0
2. In part 192, revise ``(ibr, see Sec.  192.7)'' to read 
``(incorporated by reference, see Sec.  192.7)'' wherever it appears.


Sec.  192.7  [Amended]

0
3. Paragraph (c) of Sec.  192.7 is revised to read as follows:
* * * * *
    (c) The full titles of documents incorporated by reference, in 
whole or in part, are provided herein. The numbers in parentheses 
indicate applicable editions. For each incorporated document, citations 
of all affected sections are provided. Earlier editions of currently 
listed documents or editions of documents listed in previous editions 
of 49 CFR part 192 may be used for materials and components designed, 
manufactured, or installed in accordance with these earlier documents 
at the time they were listed. The user must refer to the appropriate 
previous edition of 49 CFR part 192 for a listing of the earlier listed 
editions or documents.
    (1) Incorporated by reference (IBR).

List of Organizations and Addresses:

    A. Pipeline Research Council International, Inc. (PRCI), c/o 
Technical Toolboxes, 3801 Kirby Drive, Suite 520, Houston, TX 77098.
    B. American Petroleum Institute (API), 1220 L Street, NW., 
Washington, DC 20005.
    C. American Society for Testing and Materials (ASTM), 100 Barr 
Harbor Drive, West Conshohocken, PA 19428.
    D. ASME International (ASME), Three Park Avenue, New York, NY 
10016-5990.
    E. Manufacturers Standardization Society of the Valve and Fittings 
Industry, Inc. (MSS), 127 Park Street, NE., Vienna, VA 22180.
    F. National Fire Protection Association (NFPA), 1 Batterymarch 
Park, P.O. Box 9101, Quincy, MA 02269-9101.
    G. Plastics Pipe Institute, Inc. (PPI), 1825 Connecticut Avenue, 
NW., Suite 680, Washington, DC 20009.
    H. NACE International (NACE), 1440 South Creek Drive, Houston, TX 
77084.
    I. Gas Technology Institute (GTI), 1700 South Mount Prospect Road, 
Des Plaines, IL 60018.
    (2) Documents incorporated by reference.

------------------------------------------------------------------------
    Source and name of referenced material          49 CFR reference
------------------------------------------------------------------------
A. Pipeline Research Council International
 (PRCI):
  (1) AGA Pipeline Research Committee,         Sec.  Sec.   192.933(a);
   Project PR-3-805, ``A Modified Criterion     192.485(c).
   for Evaluating the Remaining Strength of
   Corroded Pipe,'' (December 22, 1989). The
   RSTRENG program may be used for
   calculating remaining strength.
B. American Petroleum Institute (API):
  (1) API Specification 5L ``Specification     Sec.  Sec.   192.55(e);
   for Line Pipe,'' (43rd edition and errata,   192.113; Item I of
   2004).                                       Appendix B.
  (2) API Recommended Practice 5L1             Sec.   192.65(a).
   ``Recommended Practice for Railroad
   Transportation of Line Pipe,'' (6th
   edition, 2002).
  (3) API Specification 6D ``Pipeline          Sec.   192.145(a).
   Valves,'' (22nd edition, January 2002).
  (4) API 1104 ``Welding of Pipelines and      Sec.  Sec.   192.227(a);
   Related Facilities,'' (19th edition, 1999    192.229(c)(1);
   including Errata October 31, 2001).          192.241(c); Item II,
                                                Appendix B.
  (5) API Recommended Practice 1162 ``Public   Sec.  Sec.   192.616(a);
   Awareness Programs for Pipeline              192.616(b); 192.616(c).
   Operators,'' (1st edition, December 2003).
C. American Society for Testing and Materials
 (ASTM):
  (1) ASTM A53/A53M-04a (2004) ``Standard      Sec.  Sec.   192.113;
   Specification for Pipe, Steel, Black and     Item I, Appendix B.
   Hot-Dipped, Zinc-Coated, Welded and
   Seamless.''.
  (2) ASTM A106/A106M-04b (2004) ``Standard    Sec.  Sec.   192.113;
   Specification for Seamless Carbon Steel      Item I, Appendix B.
   Pipe for High-Temperature Service.''.
  (3) ASTM A333/A333M-05 (2005) ``Standard     Sec.  Sec.   192.113;
   Specification for Seamless and Welded        Item I, Appendix B.
   Steel Pipe for Low-Temperature Service.''.
  (4) ASTM A372/A372M-03 (2003) ``Standard     Sec.   192.177(b)(1).
   Specification for Carbon and Alloy Steel
   Forgings for Thin-Walled Pressure
   Vessels.''.
  (5) ASTM A381-96 (Reapproved 2001)           Sec.  Sec.   192.113;
   ``Standard Specification for Metal-Arc       Item I, Appendix B.
   Welded Steel Pipe for Use With High-
   Pressure Transmission Systems.''.
  (6) ASTM A671-04 (2004) ``Standard           Sec.  Sec.   192.113;
   Specification for Electric-Fusion-Welded     Item I, Appendix B.
   Steel Pipe for Atmospheric and Lower
   Temperatures.''.
  (7) ASTM A672-96 (Reapproved 2001)           Sec.  Sec.   192.113;
   ``Standard Specification for Electric-       Item I, Appendix B.
   Fusion-Welded Steel Pipe for High-Pressure
   Service at Moderate Temperatures.''.
  (8) ASTM A691-98 (Reapproved 2002)           Sec.  Sec.   192.113;
   ``Standard Specification for Carbon and      Item I, Appendix B.
   Alloy Steel Pipe, Electric-Fusion-Welded
   for High-Pressure Service at High
   Temperatures.''.
  (9) ASTM D638-03 ``Standard Test Method for  Sec.  Sec.
   Tensile Properties of Plastics.''.           192.283(a)(3);
                                                192.283(b)(1).
  (10) ASTM D2513-87 ``Standard Specification  Sec.   192.63(a)(1).
   for Thermoplastic Gas Pressure Pipe,
   Tubing, and Fittings.''.
  (11) ASTM D2513-99 ``Standard Specification  Sec.  Sec.   192.191(b);
   for Thermoplastic Gas Pressure Pipe,         192.281(b)(2);
   Tubing, and Fittings.''.                     192.283(a)(1)(i); Item
                                                1, Appendix B.
  (12) ASTM D2517-00 ``Standard Specification  Sec.  Sec.   192.191(a);
   for Reinforced Epoxy Resin Gas Pressure      192.281(d)(1);
   Pipe and Fittings.''.                        192.283(a)(1)(ii); Item
                                                I, Appendix B.
  (13) ASTM F1055-1998 ``Standard              Sec.
   Specification for Electrofusion Type         192.283(a)(1)(iii).
   Polyethylene Fittings for Outside Diameter
   Controller Polyethylene Pipe and Tubing.''.
D. ASME International (ASME):
  (1) ASME B16.1-1998 ``Cast Iron Pipe         Sec.   192.147(c).
   Flanges and Flanged Fittings.''.

[[Page 33407]]

 
  (2) ASME B16.5-2003 (October 2004) ``Pipe    Sec.  Sec.   192.147(a);
   Flanges and Flanged Fittings.''.             192.279.
  (3) ASME B31G-1991 (Reaffirmed; 2004)        Sec.  Sec.   192.485(c);
   ``Manual for Determining the Remaining       192.933(a).
   Strength of Corroded Pipelines.''.
  (4) ASME B31.8-2003 (February 2004) ``Gas    Sec.   192.619(a)(1)(i).
   Transmission and Distribution Piping
   Systems.''.
  (5) ASME B31.8S-2004 ``Supplement to B31.8   Sec.  Sec.   192.903(c);
   on Managing System Integrity of Gas          192.907(b); 192.911,
   Pipelines.''.                                Introductory text;
                                                192.911(i); 192.911(k);
                                                192.911(l); 192.911(m);
                                                192.913(a) Introductory
                                                text; 192.913(b)(1);
                                                192.917(a) Introductory
                                                text; 192.917(b);
                                                192.917(c);
                                                192.917(e)(1);
                                                192.917(e)(4);
                                                192.921(a)(1);
                                                192.923(b)(2);
                                                192.923(b)(3);
                                                192.925(b) Introductory
                                                text; 102.925(b)(1);
                                                192.925(b)(2);
                                                192.925(b)(3);
                                                192.925(b)(4);
                                                192.927(b);
                                                192.927(c)(1)(i);
                                                192.929(b)(1);
                                                192.929(b)(2);
                                                192.933(a);
                                                192.933(d)(1);
                                                192.933(d)(1)(i);
                                                192.935(a);
                                                192.935(b)(1)(iv);
                                                192.937(c)(1);
                                                192.939(a)(1)(i);
                                                192.939(a)(1)(ii);
                                                192.939(a)(3);
                                                192.945(a).
  (6) ASME Boiler and Pressure Vessel Code,    Sec.   192.153(a).
   Section I, ``Rules for Construction of
   Power Boilers,'' (2004 edition, including
   addenda through July 1, 2005).
  (7) ASME Boiler and Pressure Vessel Code,    Sec.  Sec.   192.153(a);
   Section VIII, Division 1, ``Rules for        192.153(b); 192.153(d);
   Construction of Pressure Vessels,'' (2004    192.165(b)(3).
   edition, including addenda through July 1,
   2005).
  (8) ASME Boiler and Pressure Vessel Code,    Sec.  Sec.   192.153(b);
   Section VIII, Division 2, ``Rules for        192.165(b)(3).
   Construction of Pressure Vessels--
   Alternative Rules,'' (2004 edition,
   including addenda through July 1, 2005).
  (9) ASME Boiler and Pressure Vessel Code,    Sec.  Sec.   192.227(a);
   Section IX, ``Welding and Brazing            Item II, Appendix B.
   Qualifications,'' (2004 edition, including
   addenda through July 1, 2005).
E. Manufacturers Standardization Society of
 the Valve and Fittings Industry, Inc. (MSS):
  (1) MSS SP-44-1996 (Reaffirmed; 2001)        Sec.   192.147(a).
   ``Steel Pipe Line Flanges.''.
  (2) [Reserved].............................  .........................
F. National Fire Protection Association
 (NFPA):
  (1) NFPA 30 (2003) ``Flammable and           Sec.   192.735(b).
   Combustible Liquids Code.''.
  (2) NFPA 58 (2004) ``Liquefied Petroleum     Sec.   192.11(a);
   Gas Code (LP-Gas Code).''.                   192.11(b); 192.11(c).
  (3) NFPA 59 (2004) ``Utility LP-Gas Plant    Sec.  Sec.   192.11(a);
   Code.''.                                     192.11(b); 192.11(c).
  (4) NFPA 70 (2005) ``National Electrical     Sec.  Sec.   192.163(e);
   Code.''.                                     192.189(c).
G. Plastics Pipe Institute, Inc. (PPI):
  (1) PPI TR-3/2004 (2004) ``Policies and      Sec.   192.121.
   Procedures for Developing Hydrostatic
   Design Basis (HDB), Pressure Design Basis
   (PDB), Strength Design Basis (SDB), and
   Minimum Required Strength (MRS) Ratings
   for Thermoplastic Piping Materials or
   Pipe.''.
H. NACE International (NACE):
  (1) NACE Standard RP0502-2002 ``Pipeline     Sec.  Sec.
   External Corrosion Direct Assessment         192.923(b)(1);
   Methodology.''.                              192.925(b) Introductory
                                                text; 192.925(b)(1);
                                                192.925(b)(1)(ii);
                                                192.925(b)(2)
                                                Introductory text;
                                                192.925(b)(3)
                                                Introductory text;
                                                192.925(b)(3)(ii);
                                                192.925(b)(iv);
                                                192.925(b)(4)
                                                Introductory text;
                                                192.925(b)(4)(ii);
                                                192.931(d);
                                                192.935(b)(1)(iv);
                                                192.939(a)(2).
I. Gas Technology Institute (GTI):
  (1) GRI 02/0057 (2002) ``Internal Corrosion  Sec.   192.927(c)(2).
   Direct Assessment of Gas Transmission
   Pipelines Methodology.''.
------------------------------------------------------------------------


0
4. In part 192, revise ``(ibr, see Sec.  192.121)'' to read 
``(incorporated by reference, see Sec.  192.121)'' wherever it appears.

0
5. Section 192.121 is amended by revising the definition of strength 
``S'' to read as follows:


Sec.  192.121  Design of plastic pipe.

* * * * *
    S = For thermoplastic pipe, the HDB is determined in accordance 
with the listed specification at a temperature equal to 73 [deg]F (23 
[deg]C), 100 [deg]F (38 [deg]C), 120 [deg]F (49 [deg]C), or 140 [deg]F 
(60 [deg]C). In the absence of an HDB established at the specified 
temperature, the HDB of a higher temperature may be used in determining 
a design pressure rating at the specified temperature by arithmetic 
interpolation using the procedure in Part D.2. of PPI TR-3/2004, HDB/
PDB/SDB/MRS Policies (incorporated by reference, see Sec.  192.7). For 
reinforced thermosetting plastic pipe, 11,000 psig (75,842 kPa).
* * * * *

0
6. In Sec.  192.123, paragraph (e) introductory text, remove ``[insert 
effective date of final rule]'' and add in its place ``July 14, 2004''.

0
7. In part 192, revise ``(ibr, see Sec.  192.619)'' to read 
``(incorporated by reference, see Sec.  192.619)'' wherever it appears.

0
8. Section 192.619 is amended by revising paragraph (a)(1)(i) to read 
as follows:


Sec.  192.619  Maximum allowable operating pressure: Steel or plastic 
pipelines.

    (a) * * *
    (1) * * *
    (i) Eighty percent of the first test pressure that produces yield 
under section N5 of Appendix N of ASME B31.8 (incorporated by 
reference, see Sec.  192.7), reduced by the appropriate factor in 
paragraph (a)(2)(ii) of this section; or
* * * * *

0
9. In part 192, revise ``(ibr, see Sec.  192.755)'' to read 
``(incorporated by

[[Page 33408]]

reference, see Sec.  192.755)'' wherever it appears.

0
10. Part 192 is amended by removing the undesignated center heading, 
``HIGH CONSEQUENCE AREAS''.

0
11. The title of subpart O of part 192 is revised to read as follows:

Subpart O--Gas Transmission Pipeline Integrity Management

0
12. Section I of Appendix B is revised to read as follows:

Appendix B to Part 192--Qualification of Pipe

I. Listed Pipe Specifications

API 5L--Steel pipe, ``API Specification for Line Pipe'' 
(incorporated by reference, see Sec.  192.7).
ASTM A53/A53M--Steel pipe, ``Standard Specification for Pipe, Steel 
Black and Hot-Dipped, Zinc-Coated, Welded and Seamless'' 
(incorporated by reference, see Sec.  192.7).
ASTM A106--Steel pipe, ``Standard Specification for Seamless Carbon 
Steel Pipe for High Temperature Service'' (incorporated by 
reference, see Sec.  192.7).
ASTM A333/A333M--Steel pipe, ``Standard Specification for Seamless 
and Welded Steel Pipe for Low Temperature Service'' (incorporated by 
reference, see Sec.  192.7).
ASTM A381--Steel pipe, ``Standard Specification for Metal-Arc-Welded 
Steel Pipe for Use with High-Pressure Transmission Systems'' 
(incorporated by reference, see Sec.  192.7).
ASTM A671--Steel pipe, ``Standard Specification for Electric-Fusion-
Welded Pipe for Atmospheric and Lower Temperatures'' (incorporated 
by reference, see Sec.  192.7).
ASTM A672--Steel pipe, ``Standard Specification for Electric-Fusion-
Welded Steel Pipe for High-Pressure Service at Moderate 
Temperatures'' (incorporated by reference, see Sec.  192.7).
ASTM A691--Steel pipe, ``Standard Specification for Carbon and Alloy 
Steel Pipe, Electric-Fusion-Welded for High Pressure Service at High 
Temperatures'' (incorporated by reference, see Sec.  192.7).
ASTM D2513--Thermoplastic pipe and tubing, ``Standard Specification 
for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings'' 
(incorporated by reference, see Sec.  192.7).
ASTM D2517--Thermosetting plastic pipe and tubing, ``Standard 
Specification for Reinforced Epoxy Resin Gas Pressure Pipe and 
Fittings'' (incorporated by reference, see Sec.  192.7).

PART 193--[AMENDED]

0
1. The authority citation for part 193 continues to read as follows:

    Authority: 49 U.S.C. 5103, 60102, 60103, 60104, 60108, 60109, 
60110, 60113, 60118; and 49 CFR 1.53.


0
2. In part 193, revise ``(ibr, see Sec.  193.2013)'' to read 
``(incorporated by reference, see Sec.  193.2013)'' wherever it 
appears.

0
3. Section 193.2013 is revised to read as follows:


193.2013  Incorporation by reference.

    (a) Any document or portion thereof incorporated by reference in 
this part is included in this part as though it were printed in full. 
When only a portion of a document is referenced, then this part 
incorporates only that referenced portion of the document and the 
remainder is not incorporated. Applicable editions are listed in 
paragraph (c) of this section in parentheses following the title of the 
referenced material. Earlier editions listed in previous editions of 
this section may be used for components manufactured, designed, or 
installed in accordance with those earlier editions at the time they 
were listed. The user must refer to the appropriate previous edition of 
49 CFR for a listing of the earlier editions.
    (b) All incorporated materials are available for inspection in the 
Pipeline and Hazardous Materials Safety Administration, 400 Seventh 
Street, SW., Washington, DC, or at the National Archives and Records 
Administration (NARA). For information on the availability of this 
material at NARA, call 202-741-6030 or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/IBR_locations.html.
    Documents incorporated by reference are available from the 
publishers as follows:
    A. American Gas Association (AGA), 400 North Capitol Street, NW., 
Washington, DC 20001.
    B. American Society of Civil Engineers (ASCE), Parallel Centre, 
1801 Alexander Bell Drive, Reston, VA 20191-4400.
    C. ASME International (ASME), Three Park Avenue, New York, NY 
10016-5990.
    D. Gas Technology Institute (GTI), 1700 S. Mount Prospect Road, Des 
Plaines, IL 60018.
    E. National Fire Protection Association (NFPA), 1 Batterymarch 
Park, P.O. Box 9101, Quincy, MA 02269-9101.
    (c) Documents incorporated by reference.

------------------------------------------------------------------------
    Source and name of referenced material          49 CFR reference
------------------------------------------------------------------------
A. American Gas Association (AGA):
  (1) ``Purging Principles and Practices,''    Sec.  Sec.   193.2513;
   (3rd edition, 2001)..                        193.2517; 193.2615.
B. American Society of Civil Engineers
 (ASCE):
  (1) SEI/ASCE 7-02 ``Minimum Design Loads     Sec.   193.2067.
   for Buildings and Other Structures,''
   (2002 edition)..
C. ASME International (ASME):
  (1) ASME Boiler and Pressure Vessel Code,    Sec.   193.2321.
   Section VIII, Division 1, ``Rules for
   Construction of Pressure Vessels,'' (2004
   edition, including addenda through July 1,
   2005).
  (2) ASME Boiler and Pressure Vessel Code,    Sec.   193.2321.
   Section VIII, Division 2, ``Rules for
   Construction of Pressure Vessels--
   Alternative Rules,'' (2004 edition,
   including addenda through July 1, 2005).
D. Gas Technology Institute (GTI):
  (1) GRI-89/0176 ``LNGFIRE: A Thermal         Sec.   193.2057.
   Radiation Model for LNG Fires,'' (June 29,
   1990).
  (2) GTI-04/0049 (April 2004) ``LNG Vapor     Sec.   193.2059.
   Dispersion Prediction with the DEGADIS
   2.1: Dense Gas Dispersion Model for LNG
   Vapor Dispersion''.
  (3) GRI-96/0396.5 ``Evaluation of            Sec.   193.2059.
   Mitigation Methods for Accidental LNG
   Releases, Volume 5: Using FEM3A for LNG
   Accident Consequence Analyses,'' (April
   1997).
E. National Fire Protection Association
 (NFPA):
  (1) NFPA 59A (2001) ``Standard for the       Sec.  Sec.   193.2019;
   Production, Storage, and Handling of         193.2051; 193.2057;
   Liquefied Natural Gas (LNG).''.              193.2059; 193.2101;
                                                193.2301; 193.2303;
                                                193.2401; 193.2521;
                                                193.2639; 193.2801.
------------------------------------------------------------------------


[[Page 33409]]


0
4. In part 193, revise ``(ibr, see Sec.  193.2067)'' to read 
``(incorporated by reference, see Sec.  193.2067)'' wherever it 
appears.

0
5. Section 193.2067 is amended by revising paragraph (b)(1) to read as 
follows:


Sec.  193.2067  Wind forces.

* * * * *
    (b) * * *
    (1) For shop fabricated containers of LNG or other hazardous fluids 
with a capacity of not more than 70,000 gallons, applicable wind load 
data in SEI/ASCE 7-02 (incorporated by reference, see Sec.  193.2013).
* * * * *

PART 195--[AMENDED]

0
1. The authority citation for part 195 continues to read as follows:

    Authority: 49 U.S.C. 5103, 60102, 60104, 60108, 60109, 60118; 
and 49 CFR 1.53.


0
2. In part 195, revise ``(ibr, see Sec.  195.3)'' to read 
``(incorporated by reference, see Sec.  195.3)'' wherever it appears.

0
3. Section 195.3 is amended by revising section heading and paragraphs 
(b) and (c) to read as follows:


Sec.  195.3  Incorporation by reference.

* * * * *
    (b) All incorporated materials are available for inspection in the 
Pipeline and Hazardous Materials Safety Administration, 400 Seventh 
Street, SW., Washington, DC, or at the National Archives and Records 
Administration (NARA). For information on the availability of this 
material at NARA, call 202-741-6030 or go to: http://www.archives.gov/
federal--register/code--of--federal--regulations/ibr--locations.html. 
These materials have been approved for incorporation by reference by 
the Director of the Federal Register in accordance with 5 U.S.C. 552(a) 
and 1 CFR part 51. In addition, materials incorporated by reference are 
available as follows:
    1. Pipeline Research Council International, Inc. (PRCI), c/o 
Technical Toolboxes, 3801 Kirby Drive, Suite 520, Houston, TX 77098.
    2. American Petroleum Institute (API), 1220 L Street, NW., 
Washington, DC 20005.
    3. ASME International (ASME), Three Park Avenue, New York, NY 
10016-5990.
    4. Manufacturers Standardization Society of the Valve and Fittings 
Industry, Inc. (MSS), 127 Park Street, NE., Vienna, VA 22180.
    5. American Society for Testing and Materials (ASTM), 100 Barr 
Harbor Drive, West Conshohocken, PA 19428.
    6. National Fire Protection Association (NFPA), 1 Batterymarch 
Park, P.O. Box 9101, Quincy, MA 02269-9101.
    7. NACE International, 1440 South Creek Drive, Houston, TX 77084.
    (c) The full titles of publications incorporated by reference 
wholly or partially in this part are as follows. Numbers in parentheses 
indicate applicable editions:

------------------------------------------------------------------------
    Source and name of referenced material          49 CFR reference
------------------------------------------------------------------------
A. Pipeline Research Council International,
 Inc. (PRCI):
  (1) AGA Pipeline Research Committee,         Sec.   195.452(h)(4)(B).
   Project PR-3-805, ``A Modified Criterion
   for Evaluating the Remaining Strength of
   Corroded Pipe,'' (December 22, 1989). The
   RSTRENG program may be used for
   calculating remaining strength.
B. American Petroleum Institute (API):
  (1) API Specification 5L ``Specification     Sec.  Sec.
   for Line Pipe,'' (43rd edition and errata,   195.106(b)(1)(i);
   2004).                                       195.106(e).
  (2) API Specification 6D ``Pipeline          Sec.   195.116(d).
   Valves'' (22nd edition, January 2002).
  (3) API Specification 12F ``Specification    Sec.  Sec.
   for Shop Welded Tanks for Storage of         195.132(b)(1);
   Production Liquids,'' (11th edition, 1994).  195.205(b)(2);
                                                195.264(b)(1);
                                                195.264(e)(1);
                                                195.307(a); 195.565;
                                                195.579(d).
  (4) API 510 ``Pressure Vessel Inspection     Sec.  Sec.
   Code: Maintenance Inspection, Rating,        195.205(b)(3);
   Repair, and Alteration,'' (8th edition,      195.432(c).
   1997 including Addenda 1 through 4).
  (5) API 620 ``Design and Construction of     Sec.  Sec.
   Large, Welded, Low-Pressure Storage          195.132(b)(2);
   Tanks,'' (10th edition, 2002 including       195.205(b)(2);
   Addendum 1).                                 195.264(b)(1);
                                                195.264(e)(3);
                                                195.307(b).
  (6) API 650 ``Welded Steel Tanks for Oil     Sec.  Sec.
   Storage,'' (10th edition, 1998 including     195.132(b)(3);
   Addenda 1-3).                                195.205(b)(1);
                                                195.264(b)(1);
                                                195.264(e)(2); 195.307I;
                                                195.307(d); 195.565;
                                                195.579(d).
  (7) API Recommended Practice 651 ``Cathodic  Sec.  Sec.   195.565;
   Protection of Aboveground Petroleum          195.579(d).
   Storage Tanks,'' (2nd edition, December
   1997).
  (8) API Recommended Practice 652 ``Lining    Sec.   195.579(d).
   of Aboveground Petroleum Storage Tank
   Bottoms,'' (2nd edition, December 1997).
  (9) API 653 ``Tank Inspection, Repair,       Sec.  Sec.
   Alteration, and Reconstruction,'' (3rd       195.205(b)(1);
   edition, 2001 including Addendum 1, 2003).   195.432(b).
  (10) API 1104 ``Welding of Pipelines and     Sec.  Sec.   195.222;
   Related Facilities,'' (19th edition, 1999    195.228(b); 195.214(a).
   including October 31, 2001 errata).
  (11) API 1130 ``Computational Pipeline       Sec.  Sec.   195.134;
   Monitoring for Liquid Pipelines,'' (2nd      195.444.
   edition, 2002).
  (12) API 2000 ``Venting Atmospheric and Low- Sec.  Sec.
   Pressure Storage Tanks,'' (5th edition,      195.264(e)(2);
   April 1998).                                 195.264(e)(3).
  (13) API Recommended Practice 2003           Sec.   195.405(a).
   ``Protection Against Ignitions Arising Out
   of Static, Lightning, and Stray
   Currents,'' (6th edition, 1998).
  (14) API 2026 ``Safe Access/Egress           Sec.   195.405(b).
   Involving Floating Roofs of Storage Tanks
   in Petroleum Service,'' (2nd edition,
   1998).
  (15) API Recommended Practice 2350           Sec.   195.428I.
   ``Overfill Protection for Storage Tanks In
   Petroleum Facilities,'' (2nd edition,
   1996).
  (16) API 2510 ``Design and Construction of   Sec.  Sec.
   LPG Installations,'' (8th edition, 2001).    195.132(b)(3);
                                                195.205(b)(3);
                                                195.264(b)(2);
                                                195.264(e)(4);
                                                195.307(e);195.428(c);
                                                195.432(c).
  (17) API Recommended Practice 1162 ``Public  Sec.  Sec.   195.440(a);
   Awareness Programs for Pipeline              195.440(b); 195.440(c).
   Operators,'' (1st edition, December 2003).
C. ASME International (ASME):
  (1) ASME B16.9-2003 (February 2004)          Sec.   195.118(a).
   ``Factory-Made Wrought Steel Butt Welding
   Fittings''.

[[Page 33410]]

 
  (2) ASME B31.4-2002 (October 2002)           Sec.   195.452(h)(4)(i).
   ``Pipeline Transportation Systems for
   Liquid Hydrocarbons and Other Liquids''.
  (3) ASME B31G-1991 (Reaffirmed; 2004)        Sec.  Sec.
   ``Manual for Determining the Remaining       195.452(h)(4)(i)(B);
   Strength of Corroded Pipelines''.            195.452(h)(4)(iii)(D).
  (4) ASME B31.8-2003 (February 2004) ``Gas    Sec.  Sec.
   Transmission and Distribution Piping         195.5(a)(1)(i);
   Systems''.                                   195.406(a)(1)(i).
  (5) ASME Boiler and Pressure Vessel Code,    Sec.  Sec.   195.124;
   Section VIII, Division 1 ``Rules for         195.307(e).
   Construction of Pressure Vessels,'' (2004
   edition, including addenda through July 1,
   2005).
  (6) ASME Boiler and Pressure Vessel Code,    Sec.   195.307(e).
   Section VIII, Division 2 ``Rules for
   Construction for Pressure Vessels--
   Alternative Rules,'' (2004 edition,
   including addenda through July 1, 2005).
  (7) ASME Boiler and Pressure Vessel Code,    Sec.   195.222.
   Section IX ``Welding and Brazing
   Qualifications,'' (2004 edition, including
   addenda through July 1, 2005).
D. Manufacturers Standardization Society of
 the Valve and Fittings Industry, Inc. (MSS):
  (1) MSS SP-75-2004 ``Specification for High  Sec.   195.118(a).
   Test Wrought Butt Welding Fittings''.
  (2) [Reserved].............................  .........................
E. American Society for Testing and Materials
 (ASTM):
  (1) ASTM A53/A53M-04a (2004) ``Standard      Sec.   195.106(e).
   Specification for Pipe, Steel, Black and
   Hot-Dipped, Zinc-Coated Welded and
   Seamless''.
  (2) ASTM A106/A106M-04b (2004) ``Standard    Sec.   195.106(e).
   Specification for Seamless Carbon Steel
   Pipe for High-Temperature Service''.
  (3) ASTM A333/A333M-05 ``Standard            Sec.   195.106(e).
   Specification for Seamless and Welded
   Steel Pipe for Low-Temperature Service''.
  (4) ASTM A381-96 (Reapproved 2001)           Sec.   195.106(e).
   ``Standard Specification for Metal-Arc-
   Welded Steel Pipe for Use With High-
   Pressure Transmission Systems''.
  (5) ASTM A671-04 (2004) ``Standard           Sec.   195.106(e).
   Specification for Electric-Fusion-Welded
   Steel Pipe for Atmospheric and Lower
   Temperatures''.
  (6) ASTM A672-96 (Reapproved 2001)           Sec.   195.106(e).
   ``Standard Specification for Electric-
   Fusion-Welded Steel Pipe for High-Pressure
   Service at Moderate Temperatures.''.
  (7) ASTM A691-98 (Reapproved 2002)           Sec.   195.106(e).
   ``Standard Specification for Carbon and
   Alloy Steel Pipe Electric-Fusion-Welded
   for High-Pressure Service at High
   Temperatures.''.
F. National Fire Protection Association
 (NFPA):
  (1) NFPA 30 (2003) ``Flammable and           Sec.   195.264(b)(1).
   Combustible Liquids Code''.
  (2) [Reserved].............................
G. NACE International (NACE):
  (1) NACE Standard RP0169-2002 ``Control of   Sec.  Sec.   195.571;
   External Corrosion on Underground or         195.573.
   Submerged Metallic Piping Systems''.
  (2) NACE Standard RP0502-2002 ``Pipeline     Sec.   195.588.
   External Corrosion Direct Assessment
   Methodology''.
------------------------------------------------------------------------


0
4. In part 195, revise ``(ibr, see Sec.  195.116)'' to read 
``(incorporated by reference, see Sec.  195.116)'' wherever it appears.

0
5. Section 195.116 is amended by revising paragraph (d) to read as 
follows:


Sec.  195.116  Valves.

* * * * *
    (d) Each valve must be both hydrostatically shell tested and 
hydrostatically seat tested without leakage to at least the 
requirements set forth in section 10 of API Standard 6D (incorporated 
by reference, see Sec.  195.3).
* * * * *

0
6. In part 195, revise ``(ibr, see Sec.  195.264)'' to read 
``(incorporated by reference, see Sec.  195.264)'' wherever it appears.

0
7. Section 195.264 is amended by revising paragraphs (b)(1)(i), 
(b)(1)(ii), (b)(2), (e)(3), and (e)(4) to read as follows:


Sec.  195.264  Impoundment, protection against entry, normal/emergency 
venting or pressure/vacuum relief for aboveground breakout tanks.

* * * * *
    (b) * * *
    (1) * * *
    (i) Impoundment around a breakout tank must be installed in 
accordance with section 4.3.2.3.2; and
    (ii) Impoundment by drainage to a remote impounding area must be 
installed in accordance with section 4.3.2.3.1.
    (2) For tanks built to API 2510, the installation of impoundment 
must be in accordance with section 5 or 11 of API 2510 (incorporated by 
reference, see Sec.  195.3).
* * * * *
    (e) * * *
    (3) Pressure-relieving and emergency vacuum-relieving devices 
installed on low pressure tanks built to API Standard 620 must be in 
accordance with section 9 of API Standard 620 (incorporated by 
reference, see Sec.  195.3) and its references to the normal and 
emergency venting requirements in API Standard 2000 (incorporated by 
reference, see Sec.  195.3).
    (4) Pressure and vacuum-relieving devices installed on high 
pressure tanks built to API Standard 2510 must be in accordance with 
sections 7 or 11 of API 2510 (incorporated by reference, see Sec.  
195.3).

0
8. In part 195, revise ``(ibr, see Sec.  195.307)'' to read 
``(incorporated by reference, see Sec.  195.307)'' wherever it appears.

0
9. Section 195.307 is amended by revising paragraph (b) to read as 
follows:


Sec.  195.307  Pressure testing aboveground breakout tanks.

* * * * *
    (b) For aboveground breakout tanks built to API Standard 620 and 
first placed in service after October 2, 2000, hydrostatic and 
pneumatic testing must be in accordance with section 7.18 of API 
Standard 620 (incorporated by reference, see Sec.  195.3).
* * * * *

0
10. In part 195, revise ``(ibr, see Sec.  195.571)'' to read 
``(incorporated by reference, see Sec.  195.571)'' wherever it appears.

[[Page 33411]]


0
11. Section 195.571 is revised to read as follows:


Sec.  195.571   What criteria must I use to determine the adequacy of 
cathodic protection?

    Cathodic protection required by this subpart must comply with one 
or more of the applicable criteria and other considerations for 
cathodic protection contained in paragraphs 6.2 and 6.3 of NACE 
Standard RP 0169 (incorporated by reference, see Sec.  195.3).

0
12. In part 195, revise ``(ibr, see Sec.  195.573)'' to read 
``(incorporated by reference, see Sec.  195.573)'' wherever it appears.

0
13. Section 195.573 is amended by revising paragraph (a)(2) to read as 
follows:


Sec.  195.573  What must I do to monitor external corrosion control?

    (a) * * *
    (2) Identify not more than 2 years after cathodic protection is 
installed, the circumstances in which a close-interval survey or 
comparable technology is practicable and necessary to accomplish the 
objectives of paragraph 10.1.1.3 of NACE Standard RP 0169 (incorporated 
by reference, see Sec.  195.3).
* * * * *

    Issued in Washington, DC, on May 31, 2006.
Brigham A. McCown,
Acting Administrator.
 [FR Doc. E6-9059 Filed 6-8-06; 8:45 am]
BILLING CODE 4910-60-P