[Federal Register Volume 70, Number 175 (Monday, September 12, 2005)]
[Proposed Rules]
[Pages 53743-53746]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 05-17979]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2005-22383; Directorate Identifier 2005-NM-102-AD]
RIN 2120-AA64


Airworthiness Directives; Boeing Model 747-100B SUD, 747-200B, 
747-300, 747-400, and 747-400D Series Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Boeing Model 747-100B SUD, 747-300, 747-400, and 747-400D 
series airplanes; and Model 747-200B series airplanes having a 
stretched upper deck. This proposed AD would require repetitively 
inspecting for cracking or discrepancies of the fasteners in the 
tension ties, shear webs, and frames at body stations 1120 through 
1220, and related investigative and corrective actions if necessary. 
This proposed AD results from new reports of severed tension ties, as 
well as numerous reports of cracked tension ties, broken fasteners, and 
cracks in the frame, shear web, and shear ties adjacent to tension ties 
for the upper deck. We are proposing this AD to detect and correct 
cracking of the tension ties, shear webs, and frames of the upper deck, 
which could result in rapid decompression of the airplane.

DATES: We must receive comments on this proposed AD by October 27, 
2005.

ADDRESSES: Use one of the following addresses to submit comments on 
this proposed AD.
     DOT Docket Web site: Go to http://dms.dot.gov and follow 
the instructions for sending your comments electronically.
     Government-wide rulemaking Web site: Go to http://www.regulations.gov and follow the instructions for sending your 
comments electronically.
     Mail: Docket Management Facility, U.S. Department of 
Transportation, 400 Seventh Street SW., Nassif Building, Room PL-401, 
Washington, DC 20590.
     Fax: (202) 493-2251.
     Hand Delivery: Room PL-401 on the plaza level of the 
Nassif Building, 400 Seventh Street SW., Washington, DC, between 9 a.m. 
and 5 p.m., Monday through Friday, except Federal holidays.
    Contact Boeing Commercial Airplanes, P.O. Box 3707, Seattle, 
Washington 98124-2207, for the service information identified in this 
proposed AD.

FOR FURTHER INFORMATION CONTACT: Ivan Li, Aerospace Engineer, Airframe 
Branch, ANM-120S, FAA, Seattle Aircraft Certification Office, 1601 Lind 
Avenue, SW., Renton, Washington 98055-4056; telephone (425) 917-6437; 
fax (425) 917-6590.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to submit any relevant written data, views, or 
arguments regarding this proposed AD. Include the docket number ``FAA-
2005-22383; Directorate Identifier 2005-NM-102-AD'' at the beginning of 
your comments. We specifically invite comments on the overall 
regulatory, economic, environmental, and energy aspects of the proposed 
AD. We will consider all comments received by the closing date and may 
amend the proposed AD in light of those comments.
    We will post all comments we receive, without change, to http://dms.dot.gov, including any personal information you provide. We will 
also post a report summarizing each substantive verbal contact with FAA 
personnel concerning this proposed AD. Using the search function of 
that Web site, anyone can find and read the comments in any of our 
dockets, including the name of the individual who sent the comment (or 
signed the comment on behalf of an association, business, labor union, 
etc.). You may review DOT's complete Privacy Act Statement in the 
Federal Register published on April 11, 2000 (65 FR 19477-78), or you 
may visit http://dms.dot.gov.

Examining the Docket

    You may examine the AD docket on the Internet at http://dms.dot.gov, or in person at the Docket Management Facility office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The Docket Management Facility office (telephone (800) 647-
5227) is located on the plaza level of the Nassif Building at the DOT 
street address stated in the ADDRESSES section. Comments will be 
available in the AD docket shortly after the Docket Management System 
receives them.

Discussion

    We previously issued AD 2005-05-08, amendment 39-13997 (70 FR 
12113, March 11, 2005). That AD applies to certain Boeing Model 747-
100B SUD, -300, -400, and -400D series airplanes. That AD requires a 
one-time inspection for discrepancies of the fuselage frame to tension 
tie joints at body stations (BS) 1120 through 1220, and to determine if 
steel splice plates are installed on the fuselage frames, and related 
investigative and corrective actions. That AD was prompted by reports 
of severed tension ties found at the fuselage frame joints at BS 1120 
and 1140. These severed tension ties resulted from fatigue cracking due 
to an incorrect configuration (installation of aluminum splice plates 
instead of steel splice plates during the manufacturing process).
    Since we issued AD 2005-05-08, we have received additional reports 
of severed tension ties. While these severed tension ties were also 
attributed to fatigue, the tension ties in these cases were properly 
configured according to the applicable Boeing Engineering Drawings. We 
have also received numerous reports of fatigue cracking of tension 
ties, as well as broken fasteners and cracks in the frame and shear 
ties adjacent to tension ties for the upper deck between BS 1120 and 
1220. Also, we have received reports of cracking in the shear web 
between the BS 1120 and BS 1140 tension ties. Cracking of the tension 
ties, shear webs, and frames of the upper deck; if not corrected; could 
result in rapid decompression of the airplane.
    Certain Boeing 747-200B series airplanes have been modified under a 
certain Boeing-owned supplemental type certificate to include a 
stretched upper deck (SUD). These airplanes

[[Page 53744]]

would also be subject to the same unsafe condition revealed on Boeing 
Model 747-100B SUD, -300, -400, and -400D series airplanes.

Relevant Service Information

    We have reviewed Boeing Alert Service Bulletin 747-53A2507, dated 
April 21, 2005. The service bulletin describes procedures for 
repetitive ``Stage 1'' and ``Stage 2'' inspections for cracking or 
discrepancies of the fasteners in the tension ties, shear webs, and 
frames at body stations 1120 through 1220; and related investigative 
and corrective actions if necessary.
    The procedures for Stage 1 inspections involve the following 
inspections to detect cracking or broken, loose, or missing fasteners:
     A detailed inspection of the tension ties and steel plates 
from BS 1120 through BS 1220.
     A detailed inspection of the shear web components that 
attach to the BS 1120 and 1140 tension ties.
     A detailed inspection of each frame from two stringers 
above to two stringers below the tension ties from BS 1120 through BS 
1220.
    If no severed tension tie is found during a Stage 1 inspection, but 
a crack is found in a tension tie, steel plate, shear web component, or 
frame; or a broken, loose, or missing fastener is found; the service 
bulletin specifies doing a ``Structure Repair,'' which includes further 
investigative actions. Procedures for the Structure Repair include 
removing fasteners, performing open-hole high frequency eddy current 
(HFEC) inspections for cracking, repairing any cracking, and installing 
new fasteners, as applicable. For repairing certain conditions, the 
service bulletin specifies to contact Boeing for instructions.
    If a severed tension tie is found during a Stage 1 inspection, the 
service bulletin specifies further investigative actions that involve 
removing certain fasteners and steel plates, and doing additional open-
hole HFEC inspections and detailed inspections of certain fastener 
holes, adjacent tension ties, the frame web, the frame inner chord, the 
fail-safe chord, shear ties, and fasteners to detect cracking or 
broken, loose, or missing fasteners. The service bulletin specifies to 
contact Boeing for instructions for repairing the severed tension tie, 
and doing the Structure Repair described previously for any other 
cracks or broken, loose, or missing fasteners.
    Stage 2 inspections are more intensive inspections than Stage 1 
inspections and are intended for airplanes with a higher number of 
total flight cycles. Accomplishing the initial Stage 2 inspection 
eliminates the need for the Stage 1 inspections. The procedures for 
Stage 2 inspections involve the following actions:
     Removing certain fasteners and steel plates and performing 
open-hole HFEC inspections for cracking of the fastener holes in the 
tension ties, frames, and steel plates.
     Performing surface HFEC inspections for cracking around 
other fastener locations and in other areas of the tension ties.
     Performing a detailed inspection of each entire tension 
tie and the attaching fasteners to detect cracking or broken, loose, or 
missing fasteners.
     Performing a detailed inspection of the shear web 
components that attach to the tension ties to detect cracking or 
broken, loose, or missing fasteners.
     Performing a detailed inspection of each frame from two 
stringers above to two stringers below the tension ties to detect 
cracking or broken, loose, or missing fasteners.
     Performing an open-hole HFEC inspection for cracking of 
any frame at which an insulation blanket stud goes through a hole in 
the frame.
    If no tension tie is found severed during a Stage 2 inspection, but 
a crack is found in a tension tie, steel plate, shear web component, or 
frame; or a broken, loose, or missing fastener is found; the service 
bulletin specifies doing the Structure Repair, and installing steel 
plates and new fasteners.
    If a severed tension tie is found during a Stage 2 inspection, the 
service bulletin specifies further investigative actions that involve 
removing certain fasteners and steel plates, and doing additional 
detailed inspections of the frame common to the severed tension tie; 
including the frame web, frame inner chord, fail-safe chord, shear 
ties, and fasteners; to detect cracking or broken, loose, or missing 
fasteners. The service bulletin specifies to contact Boeing for 
instructions for repairing the severed tension tie; and doing the 
Structure Repair for any other crack or broken, loose, or missing 
fasteners.
    As part of the procedures for the Structure Repair, the service 
bulletin describes procedures for an ``Oversize Hole Repair,'' which 
may be used to repair a crack found in a fastener hole. The procedures 
for the Oversize Hole Repair include oversizing the hole to remove the 
crack, doing an open-hole HFEC inspection to make sure the crack has 
been removed, repeating the oversizing until the crack is removed, and 
installing new fasteners. The service bulletin specifies contacting 
Boeing for instructions if cracking is outside specified limits.
    The service bulletin also specifies reporting findings from both 
Stage 1 and Stage 2 inspections to Boeing.
    Accomplishing the actions specified in the service information is 
intended to adequately address the unsafe condition.
    Paragraph 1.E., ``Compliance,'' of the service bulletin specifies a 
compliance time for the initial Stage 1 inspection of 8,000 total 
flight cycles, 1,500 flight cycles after the original issue date of the 
service bulletin, or 4,000 flight cycles after inspection in accordance 
with Boeing Service Bulletin 747-53-2483, whichever is later. (AD 2005-
05-08, described previously, requires inspections in accordance with 
Boeing Service Bulletin 747-53-2483, Revision 1, dated August 28, 
2003.) The repetitive interval for Stage 1 inspections is 4,000 flight 
cycles. The service bulletin specifies that Stage 1 inspections end 
when Stage 2 inspections apply. The service bulletin specifies that the 
initial Stage 2 inspection should be done before the accumulation of 
16,000 total flight cycles, or within 1,000 flight cycles after the 
original issue date of the service bulletin, whichever is later. The 
service bulletin specifies a repetitive interval of 3,000 flight cycles 
for the Stage 2 inspections.

Other Relevant Rulemaking

    We have previously issued AD 2004-07-22, amendment 39-13566 (69 FR 
18250, April 7, 2004). That AD applies to all Boeing Model 747 series 
airplanes, and requires revising the FAA-approved maintenance or 
inspection program to include repetitive inspections for discrepancies 
of various structural significant items (SSIs); as listed in Boeing 
Document No. D6-35022, ``Supplemental Structural Inspection Document 
(SSID),'' Revision G, dated December 2000 (referred to after this as 
``the SSID''); and repair if necessary. The repetitive inspections of 
the tension ties that would be required by this proposed AD are 
approved as an alternative method of compliance for the inspections of 
SSI F-19A of the SSID, as required by paragraphs (c) and (d) of AD 
2004-07-22. All other provisions of AD 2004-07-22 continue to apply.

FAA's Determination and Requirements of the Proposed AD

    We have evaluated all pertinent information and identified an 
unsafe condition that is likely to exist or develop on other airplanes 
of this same type design. For this reason, we are

[[Page 53745]]

proposing this AD, which would require accomplishing the actions 
specified in the service information described previously, except as 
discussed under ``Differences Between the Proposed AD and the Service 
Bulletin.''

Differences Between the Proposed AD and Service Information

    The service bulletin specifies that you may contact the 
manufacturer for instructions on how to repair certain conditions, but 
this proposed AD would require you to repair those conditions in one of 
the following ways:
     Using a method that we approve; or
     Using data that meet the certification basis of the 
airplane, and that have been approved by an Authorized Representative 
for the Boeing Delegation Option Authorization Organization whom we 
have authorized to make those findings.
    The Accomplishment Instructions of the service bulletin specifies 
reporting inspection findings to Boeing. This proposed AD would not 
require that action. We do not need this information from operators.
    The service bulletin specifies a grace period relative to original 
issue date of the service bulletin; however, this proposed AD would 
require compliance before the specified compliance time after the 
effective date of this AD.
    These differences have been coordinated with the manufacturer.

Clarification of Compliance Time for Stage 1 Inspections

    As explained previously, the referenced service bulletin specifies 
a compliance time for the Stage 1 inspections of 8,000 total flight 
cycles, 1,500 flight cycles after the original issue date of the 
service bulletin, or 4,000 flight cycles after inspection in accordance 
with Boeing Service Bulletin 747-53-2483, whichever is later. AD 2005-
05-08, described previously, requires accomplishment of Boeing Service 
Bulletin 747-53-2483 for airplanes listed in that service bulletin. 
However, we find that this proposed AD would apply to certain airplanes 
not subject to AD 2005-05-08. Thus, we find that, for airplanes not 
subject to the inspection in Boeing Service Bulletin 747-53-2483, the 
applicable compliance time for the Stage 1 inspections that would be 
required by this proposed AD is 8,000 total flight cycles, or 1,500 
flight cycles after the effective date of this AD, whichever is later. 
We have added a statement to paragraph (f)(1) of this proposed AD to 
clarify this compliance time.

Interim Action

    We consider this proposed AD interim action. The manufacturer is 
currently developing a modification that will address the unsafe 
condition identified in this AD. Once this modification is developed, 
approved, and available, we may consider additional rulemaking.

Costs of Compliance

    There are about 622 airplanes of the affected design in the 
worldwidefleet. The following table provides the estimated costs for 
U.S. operators to comply with this proposed AD.

                                                                     Estimated Costs
--------------------------------------------------------------------------------------------------------------------------------------------------------
                                                                                                   Number of
                                              Average                                                U.S.-
            Action              Work hours   labor rate             Cost per airplane              registered                  Fleet cost
                                              per hour                                             airplanes
--------------------------------------------------------------------------------------------------------------------------------------------------------
Stage 1 Inspection, per                 19          $65  $1,235, per inspection cycle...........           76  $93,860, per inspection cycle.*
 inspection cycle *.
Stage 2 Inspection, per                 83           65  $5,395, per inspection cycle...........           76  $410,020, per inspection cycle.
 inspection cycle.
--------------------------------------------------------------------------------------------------------------------------------------------------------
* Completing the initial Stage 2 inspection ends the repetitive Stage 1 inspections.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
subtitle VII, part A, subpart III, section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We have determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that the proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket. See the 
ADDRESSES section for a location to examine the regulatory evaluation.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The Federal Aviation Administration (FAA) amends Sec.  39.13 by 
adding the following new airworthiness directive (AD):


[[Page 53746]]


Boeing: Docket No. FAA-2005-22383; Directorate Identifier 2005-NM-
102-AD.

Comments Due Date

    (a) The FAA must receive comments on this AD action by October 
27, 2005.

Affected ADs

    (b) Accomplishing the requirements of paragraph (f) of this AD 
terminates the corresponding inspection requirements for the upper 
deck tension tie as required by paragraphs (c) and (d) of AD 2004-
07-22, amendment 39-13566, as those paragraphs apply to inspections 
of SSI F-19A, as identified in Boeing Document No. D6-35022, 
``Supplemental Structural Inspection Document,'' Revision G, dated 
December 2000. All other requirements of AD 2004-07-22 continue to 
apply.
    Applicability: (c) This AD applies to Boeing Model 747-100B SUD, 
747-300, 747-400, and 747-400D series airplanes; and Model 747-200 
series airplanes having a stretched upper deck; certificated in any 
category; as identified in Boeing Alert Service Bulletin 747-
53A2507, dated April 21, 2005.

Unsafe Condition

    (d) This AD results from new reports of severed tension ties, as 
well as numerous reports of cracked tension ties, broken fasteners, 
and cracks in the frame, shear web, and shear ties adjacent to 
tension ties for the upper deck. We are issuing this AD to detect 
and correct cracking of the tension ties, shear webs, and frames of 
the upper deck, which could result in rapid decompression of the 
airplane.
    Compliance: (e) You are responsible for having the actions 
required by this AD performed within the compliance times specified, 
unless the actions have already been done.

Repetitive Inspections and Corrective Actions

    (f) Do repetitive detailed and high frequency eddy current 
inspections, as applicable, for cracking or discrepancies of the 
fasteners in the tension ties, shear webs, and frames at body 
stations 1120 through 1220, and related investigative and corrective 
actions as applicable, by doing all actions in accordance with the 
Accomplishment Instructions of Boeing Alert Service Bulletin 747-
53A2507, dated April 21, 2005, except as provided by paragraphs (g) 
and (h) of this AD. Do the initial and repetitive Stage 1 and Stage 
2 inspections at the applicable times specified in Paragraph 1.E., 
``Compliance,'' of the service bulletin, except as provided by 
paragraphs (f)(1), (f)(2), and (f)(3) of this AD. Any applicable 
investigative and corrective actions must be done before further 
flight. Doing the initial Stage 2 inspection ends the repetitive 
Stage 1 inspections.
    (1) For any airplane not identified in and subject to 
inspections in accordance with Boeing Service Bulletin 747-53-2483: 
Do the initial Stage 1 inspection in accordance with Boeing Alert 
Service Bulletin 747-53A2507 before the accumulation of 8,000 total 
flight cycles, or within 1,500 flight cycles after the effective 
date of this AD, whichever is later.
    (2) Where Paragraph 1.E., ``Compliance,'' of the service 
bulletin specifies a compliance time relative to the original issue 
date of the service bulletin, this AD requires compliance before the 
specified compliance time after the effective date of this AD.
    (3) For any airplane that reaches the applicable compliance time 
for the initial Stage 2 inspection (as specified in Table 1, 
Compliance Recommendations, under paragraph 1.E. of the service 
bulletin) before reaching the applicable compliance time for the 
initial Stage 1 inspection: Doing the initial Stage 2 inspection 
eliminates the need to do the Stage 1 inspection.

Exception to Corrective Action Instructions

    (g) If any discrepancy; including but not limited to cracking, 
or broken, loose, or missing fasteners; is found during any 
inspection required by this AD, and Boeing Alert Service Bulletin 
747-53A2507, dated April 21, 2005, specifies to contact Boeing for 
appropriate action: Before further flight, repair the discrepancy 
using a method approved in accordance with paragraph (i) of this AD.

No Reporting Requirement

    (h) Although Boeing Alert Service Bulletin 747-53A2507, dated 
April 21, 2005, specifies reporting inspection findings to the 
manufacturer, this AD does not include that requirement.

Alternative Methods of Compliance (AMOCs)

    (i)(1) The Manager, Seattle Aircraft Certification Office (ACO), 
FAA, has the authority to approve AMOCs for this AD, if requested in 
accordance with the procedures found in 14 CFR 39.19.
    (2) An AMOC that provides an acceptable level of safety may be 
used for any repair required by this AD, if it is approved by an 
Authorized Representative for the Boeing Commercial Airplanes 
Delegation Option Authorization Organization who has been authorized 
by the Manager, Seattle ACO, to make those findings. For a repair 
method to be approved, the repair must meet the certification basis 
of the airplane, and the approval must specifically refer to this 
AD.

    Issued in Renton, Washington, on August 24, 2005.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 05-17979 Filed 9-9-05; 8:45 am]
BILLING CODE 4910-13-P