[Federal Register Volume 70, Number 158 (Wednesday, August 17, 2005)]
[Proposed Rules]
[Pages 48362-48368]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 05-16226]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

National Highway Traffic Safety Administration

49 CFR Part 571

[Docket No. NHTSA-2005-22093]
RIN 2127-AJ31


Federal Motor Vehicle Safety Standards; Theft Protection

AGENCY: National Highway Traffic Safety Administration (NHTSA), 
Department of Transportation.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: Our safety standard on theft protection specifies vehicle 
performance

[[Page 48363]]

requirements intended to reduce the incidence of crashes resulting from 
theft and accidental rollaway of motor vehicles. As a result of 
technological advances in the area of theft protection, the terminology 
used in the regulatory text of the Standard has become outdated and 
incompatible with key-locking systems that employ electronic codes to 
lock and unlock the vehicle, and to enable engine activation. This 
document proposes to amend and reorganize the regulatory text of the 
Standard so that it better correlates to modern theft protection 
technology and reflects the agency's interpretation of the existing 
requirements. The proposed requirements would not impose any new 
substantive requirements on vehicle manufacturers.

DATES: You should submit your comments early enough to ensure that 
Docket Management receives them not later than October 17, 2005.

ADDRESSES: You may submit comments identified by the DOT Docket Number 
cited in the heading of this document by any of the following methods:
     Web Site: http://dms.dot.gov. Follow the instructions for 
submitting comments on the DOT electronic docket site.
     Fax: 1-202-493-2251.
     Mail: Docket Management Facility; U.S. Department of 
Transportation, 400 7th Street, SW., Nassif Building, Room PL-401, 
Washington, DC 20590-001.
     Hand Delivery: Room PL-401, 400 7th Street, SW., 
Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, 
except Federal holidays.
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the online instructions for submitting 
comments.
    Instructions: All submissions must include the agency name and 
docket number. Note that all comments received will be posted without 
change to http://dms.dot.gov including any personal information 
provided. Please see the Privacy Act heading under Regulatory Notices.
    Docket: For access to the docket to read background documents or 
comments received, go to http://dms.dot.gov at any time or to Room PL-
401 on the plaza level of the Nassif Building, 400 7th Street, SW., 
Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, 
except Federal holidays.

FOR FURTHER INFORMATION CONTACT: For technical issues: Ms. Gayle 
Dalrymple, Office of Crash Avoidance Standards, NVS-123, NHTSA, 400 7th 
Street, SW., Washington, DC 20590. Telephone: (202) 366-5559. E-mail: 
[email protected].
    For legal issues: Mr. George Feygin, Office of the Chief Counsel, 
NCC-112, NHTSA, 400 7th Street, SW., Washington, DC 20590. Telephone: 
(202) 366-5834. E-mail: [email protected].

SUPPLEMENTARY INFORMATION:

Table of Contents

I. Background
II. Recent Letters of Interpretation Regarding FMVSS No. 114
III. VW Petition for Rulemaking
IV. Proposed Changes to the Regulatory Text
V. Effective Date of the Proposed Changes
VI. Request for Comments
VII. Rulemaking Analyses and Notices
    A. Executive Order 12866 and DOT Regulatory Policies and 
Procedures
    B. Executive Order 13132 (Federalism)
    C. Executive Order 13045
    D. Civil Justice Reform
    E. Regulatory Flexibility Act
    F. Paperwork Reduction Act
    G. National Technology Transfer And Advancement Act
    H. Unfunded Mandates Reform Act
    I. Regulation Identifier Number (RIN)
    J. Privacy Act
    K. Plain Language
    K. National Environmental Policy Act
VIII. Regulatory Text

I. Background

    FMVSS No. 114, Theft protection, specifies vehicle performance 
requirements intended to reduce the incidence of crashes resulting from 
theft and accidental rollaway of motor vehicles. The standard applies 
to all passenger cars, and to trucks and multipurpose passenger 
vehicles with a GVWR of 4536 kilograms (10,000 pounds) or less. The 
standard first became effective on January 1, 1970.\1\ The purpose of 
the standard was to prevent crashes caused by unauthorized use of 
unattended motor vehicles. Thus, the standard sought to ensure that the 
vehicle could not be easily operated without the key, and that the 
vehicle operator would not forget to remove the key from the ignition 
system upon exiting the vehicle.
---------------------------------------------------------------------------

    \1\ See 33 FR 6471 (April 24, 1968).
---------------------------------------------------------------------------

    In response to the problem of accidental rollaway crashes resulting 
from children inadvertently moving the automatic transmission lever to 
a neutral position when a stationary vehicle is parked on a slope, 
NHTSA later amended FMVSS No. 114 to require that the automatic 
transmission lever be locked in the ``park'' position before the key 
can be removed from the ignition system.\2\ Subsequently, NHTSA amended 
these new requirements to permit an override device that would enable 
the vehicle operator to remove the key without the transmission being 
locked in ``park,'' and to move the transmission lever without using 
the key, under certain circumstances. The purpose of these override 
provisions was to address certain situations when it may be necessary 
to remove key without shifting the transmission lever because the 
vehicle has become disabled.\3\
---------------------------------------------------------------------------

    \2\ See 55 FR 21868, (May 30, 1990).
    \3\ See 56 FR 12464 (March 26, 1991).
---------------------------------------------------------------------------

    While FMVSS No. 114 evolved to address not only theft protection, 
but also accidental rollaway prevention, the terminology used in the 
regulatory text has remained unchanged since its introduction more than 
35 years ago. However, theft protection technology has advanced 
considerably during that time. As a result, certain provisions of the 
Standard have become increasingly ambiguous when applied to modern 
theft protection technology not contemplated by the Standard when it 
first went into effect.
    For example, a number of vehicles now feature electronic systems. 
Typically, this involves a card or a similar device that is carried in 
an occupant's pocket or purse. The card carries an electronic code that 
acts as the key when it is transmitted to the vehicle's onboard locking 
system. The vehicle has a sensor that automatically unlocks the door 
and allows the vehicle operator to activate the engine, when it 
receives the code. The code-carrying device (i.e., card or otherwise) 
never has to leave the vehicle operator's pocket or purse and is not 
inserted into the ignition module.
    In response to manufacturers' requests, NHTSA issued a series of 
interpretation letters explaining how the Standard applied to various 
key-locking systems that did not utilize conventional keys, but instead 
relied on electronic codes to lock and unlock the vehicle, and to 
enable engine activation.
    In 2002, NHTSA received a petition for rulemaking from Volkswagen 
of America (VW) asking the agency to amend a certain provision of the 
standard related to rollaway prevention, that will be discussed below. 
The agency decided to grant the petitioner's request. However, instead 
of addressing only the limited issues raised by VW, this document takes 
a broader approach and proposes to amend and reorganize the regulatory 
text of FMVSS No. 114 so that it better correlates to modern antitheft 
technology and reflects the agency's interpretation of the existing 
requirements.

[[Page 48364]]

II. Recent Letters of Interpretation Regarding FMVSS No. 114

    As noted above, the agency received several requests for legal 
interpretation of the requirements of FMVSS No. 114, as they apply to 
key-locking systems using various remote access devices. In response, 
the agency has stated that the electronic code transmitted from a 
remote device to the vehicle can be considered a ``key'' for the 
purposes of FMVSS No. 114.\4\ We have also elaborated on how other 
provisions of the standard applies to electronic codes. For example, 
the agency stated that the narrow provisions related to electrical 
failure do not apply to electronically coded cards or other means used 
to enter an electronic key code into the locking system because those 
provisions were specifically crafted in the context of traditional 
keys.\5\ We also explained that systems using an electronic code 
instead of conventional key would satisfy the rollaway prevention 
provisions if the code remained in the vehicle until the transmission 
gear is locked in the ``park'' position.
---------------------------------------------------------------------------

    \4\ See http://www.nhtsa.dot.gov/cars/rules/interps/files/GF001689.html and http://www.nhtsa.dot.gov/cars/rules/interps/files/7044.html.
    \5\ See http://www.nhtsa.dot.gov/cars/rules/interps/files/GF001689.html.
---------------------------------------------------------------------------

    We have followed our interpretation of the definition of ``key'' in 
addressing other issues related to FMVSS No. 114. However, instead of 
relying on interpretations, and possibly facing additional questions in 
the future, the agency believes that it is appropriate to amend the 
regulatory text of FMVSS No. 114 so that it better correlates to modern 
antitheft technology and better reflects the agency's interpretation of 
the existing requirements. The specifics of our proposal are discussed 
in Section IV below.

III. VW Petition for Rulemaking

    As previously discussed, in order to prevent accidental rollaways, 
the Standard currently requires that, for vehicles with automatic 
transmission, the transmission lever must be locked in ``park'' before 
the vehicle operator could remove the key.\6\ However, the Standard 
also allows an optional ``override device'' which permits removal of 
the key without the automatic transmission being locked in ``park.'' 
The standard currently specifies that this override device ``* * * must 
be covered by a non-transparent surface which, when installed, prevents 
sight of and activation of the device * * *'' and that ``* * * The 
covering surface shall be removable only by use of a screwdriver or 
other tool.''
---------------------------------------------------------------------------

    \6\ See S4.2.2(a) of FMVSS No. 114.
---------------------------------------------------------------------------

    On October 29, 2002, NHTSA received a petition from VW asking the 
agency to amend S4.2.2(a) by removing provisions related to the 
override device covering. VW argued that these provisions are 
unnecessarily design-restrictive. VW indicated that there are other 
ways to ensure that the override device is not engaged inadvertently. 
Specifically, VW suggested that the agency allow an override device 
that requires using a tool to activate the override device while 
simultaneously removing the key.
    The agency agrees that the regulatory text related to the override 
device cover is unnecessarily design-restrictive. Accordingly, this 
document grants the VW petition for rulemaking and proposes to amend 
the relevant portions of the regulatory text.

IV. Proposed Changes to the Regulatory Text

    First, the agency is proposing to reorganize the regulatory text of 
the Standard such that the requirements related to theft protection are 
separated from the requirements intended to prevent accidental 
rollaway. Second, whenever possible, we are proposing to simplify the 
language used in the Standard to make it more clear. Finally, this 
document proposes to amend requirements and definitions that are 
unnecessarily design-restrictive.
    While we discuss certain specific aspects of our proposal below, we 
encourage readers to carefully examine each paragraph of the proposed 
regulatory text because the entire text is revised.
    1. We are proposing to revise the paragraphs explaining the 
Standard's scope and purpose to better reflect its goal of reducing the 
incidence of crashes resulting from theft and also accidental rollaway 
of motor vehicles. This change has no substantive significance because 
the Standard already addresses both safety concerns, and should not be 
viewed as broadening the scope of the current requirements.
    2. We are proposing to revise the definition of ``key'' such that 
it makes it appropriate not only for conventional keys but also 
electronic codes and other potential means of unlocking and operating 
the vehicle. We believe that the new definition is broad enough to 
include not only electronic codes but also other technologies, 
including, for example, fingerprint recognition.
    3. The current standard uses the term ``transmission shift lever'' 
in several instances to refer to the mechanism by which the driver 
changes the transmission from one gear to another. The agency believes 
that this term is unnecessarily design-specific. We have therefore 
substituted the term ``gear selection control'' for the term 
``transmission shift lever.''
    4. As previously discussed, S4.2.1 of the current Standard 
specifies that a key cannot be removed from the ignition until the 
transmission shift lever is locked in ``park.'' However, the Standard 
provides for an optional override device designed to allow (a) removal 
of the key when the transmission is not in the ``park,'' and (b) moving 
the transmission out of ``park'' when the key is not in the ignition. 
The Standard requires that the means for activating this device must be 
covered by a non-transparent surface which, when installed, prevents 
sight of and activation of the device. This covering surface can only 
be removable by use of a tool.\7\
---------------------------------------------------------------------------

    \7\ The purpose of this requirement was to ensure that children 
could not easily gain access to the override device (see 56 FR 12464 
at 12466).
---------------------------------------------------------------------------

    In response to the VW petition described above, we are proposing to 
amend the requirement that the override device be covered by a non-
transparent surface. Specifically, as an alternative to the current 
requirement, we are proposing to permit an override device that 
requires using a tool to activate the override device while 
simultaneously removing the key. We believe that requiring the use of a 
tool in order to activate this type of override device would involve 
sufficient complexity to prevent possible inadvertent activation by a 
child.
    5. The current Standard allows only override systems that prevent 
steering before the key can be released, or the transmission lever can 
be shifted. The agency previously indicated that this requirement 
ensured that the theft protection aspects of the standard remained 
intact even in certain situations where the vehicle was disabled.\8\ 
After further evaluating this aspect of our requirements, we 
tentatively conclude that an override device that would prevent forward 
self-mobility (such as an immobilizer) instead of steering would be 
just as effective. As explained in our September 24, 2004 
interpretation letter to a party who requested confidentiality:
---------------------------------------------------------------------------

    \8\ See id. at 12467.

    We note that in promulgating FMVSS No. 114, the agency expressed 
concern about car thieves who could bypass the ignition lock. In 
response to this concern, the agency decided to require a device, 
which would prevent either self-mobility or steering even if the 
ignition lock were bypassed (see 33 FR 4471, April 27, 1968).

[[Page 48365]]

    The engine control module immobilizer described in your letter 
satisfies the requirements of S4.2(b) because it locks out the 
engine control module if an attempt is made to start the vehicle 
without the correct key or to bypass the electronic ignition system. 
When the engine control module is locked, the vehicle is not capable 
of forward self-mobility because it is incapable of moving forward 
under its own power.\9\
---------------------------------------------------------------------------

    \9\ http://www.nhtsa.dot.gov/cars/rules/interps/files/GF005229-2.html.

    Further, as explained in our May 27, 2003 interpretation letter to 
Jaguar, preventing steering after a moving vehicle has experienced a 
complete loss of electrical power would not be appropriate before a 
vehicle could be safely stopped.\10\ Therefore, we are proposing to 
amend this aspect of the override provisions to allow manufacturers 
greater flexibility in designing their override devices and to allow 
manufacturers the choice to use electronic theft prevention devices, 
such as immobilizers, instead of using steering locks if they desire.
---------------------------------------------------------------------------

    \10\ http://www.nhtsa.dot.gov/cars/rules/interps/files/GF001689.html.
---------------------------------------------------------------------------

V. Effective Date of the Proposed Changes

    As previously discussed, with the exception of the override 
provisions, which would be made less restrictive, the proposed 
amendments would not make substantive changes to the existing standard. 
Instead, we are proposing to amend and reorganize the regulatory text 
of FMVSS No. 114 so that it better correlates to modern theft 
protection technology and reflects the agency's interpretation of the 
existing requirements. We believe vehicle manufacturers would not have 
to make any changes to their vehicles if this proposal was made final. 
Accordingly, we propose to make this document effective 60 days 
following the publication of the final rule.

VI. Request for Comments

How Do I Prepare and Submit Comments?

    Your comments must be written and in English. To ensure that your 
comments are correctly filed in the Docket, please include the docket 
number of this document in your comments. Your comments must not be 
more than 15 pages long.\11\ We established this limit to encourage you 
to write your primary comments in a concise fashion. However, you may 
attach necessary additional documents to your comments. There is no 
limit on the length of the attachments. Please submit two copies of 
your comments, including the attachments, to Docket Management at the 
address given above under ADDRESSES. Comments may also be submitted to 
the docket electronically by logging onto the Docket Management System 
Web site at http://dms.dot.gov. Click on ``Help & Information'' or 
``Help/Info'' to obtain instructions for filing the document 
electronically. If you are submitting comments electronically as a PDF 
(Adobe) file, we ask that the documents submitted be scanned using 
Optical Character Recognition (OCR) process, thus allowing the agency 
to search and copy certain portions of your submissions.\12\
---------------------------------------------------------------------------

    \11\ See 49 CFR 553.21.
    \12\ Optical character recognition (OCR) is the process of 
converting an image of text, such as a scanned paper document or 
electronic fax file, into computer-editable text.
---------------------------------------------------------------------------

    Please note that pursuant to the Data Quality Act, in order for 
substantive data to be relied upon and used by the agency, it must meet 
the information quality standards set forth in the OMB and DOT Data 
Quality Act guidelines. Accordingly, we encourage you to consult the 
guidelines in preparing your comments. OMB's guidelines may be accessed 
at http://www.whitehouse.gov/omb/fedreg/reproducible.html. DOT's 
guidelines may be accessed at http://dmses.dot.gov/submit/DataQualityGuidelines.pdf.

How Can I Be Sure That My Comments Were Received?

    If you wish Docket Management to notify you upon its receipt of 
your comments, enclose a self-addressed, stamped postcard in the 
envelope containing your comments. Upon receiving your comments, Docket 
Management will return the postcard by mail.

How Do I Submit Confidential Business Information?

    If you wish to submit any information under a claim of 
confidentiality, you should submit three copies of your complete 
submission, including the information you claim to be confidential 
business information, to the Chief Counsel, NHTSA, at the address given 
above under FOR FURTHER INFORMATION CONTACT. In addition, you should 
submit two copies, from which you have deleted the claimed confidential 
business information, to Docket Management at the address given above 
under ADDRESSES. When you send a comment containing information claimed 
to be confidential business information, you should include a cover 
letter setting forth the information specified in our confidential 
business information regulation.\13\
---------------------------------------------------------------------------

    \13\ See 49 CFR part 512.
---------------------------------------------------------------------------

Will the Agency Consider Late Comments?

    We will consider all comments that Docket Management receives 
before the close of business on the comment closing date indicated 
above under DATES. To the extent possible, we will also consider 
comments that Docket Management receives after that date. If Docket 
Management receives a comment too late for us to consider in developing 
a final rule (assuming that one is issued), we will consider that 
comment as an informal suggestion for future rulemaking action.

How Can I Read the Comments Submitted by Other People?

    You may read the materials placed in the docket for this document 
(e.g., the comments submitted in response to this document by other 
interested persons) by going to the street address given above under 
ADDRESSES. The hours of the Docket Management System (DMS) are 
indicated above in the same location.
    You may also read the materials on the Internet. To do so, take the 
following steps:
    (1) Go to the Web page of the Department of Transportation DMS 
(http://dms.dot.gov/search/searchFormSimple.cfm).
    (2) On that page type in the five-digit docket number cited in the 
heading of this document. After typing the docket number, click on 
``search.''
    (3) On the next page (``Docket Search Results''), which contains 
docket summary information for the materials in the docket you 
selected, scroll down and click on the desired materials. You may 
download the materials.

VII. Rulemaking Analyses and Notices

A. Executive Order 12866 and DOT Regulatory Policies and Procedures

    This rulemaking document was not reviewed under Executive Order 
12866, ``Regulatory Planning and Review.'' The agency has considered 
the impact of this proposal under the Department of Transportation's 
regulatory policies and procedures, and has determined that it is not 
significant.
    This document proposes to amend and reorganize the regulatory text 
of 49 CFR 571.114 so that it better correlates to modern theft 
protection technology and better reflects the agency's interpretation 
of the existing requirements. Additionally, this document proposes to 
make certain

[[Page 48366]]

provisions of 49 CFR 571.114 less restrictive. If made final, the 
vehicle manufacturers would not have to make any changes to their 
vehicles as a result of this rule. The impacts of this proposed rule 
are so minor that we determined that a separate regulatory evaluation 
is not needed.

B. Executive Order 13132 (Federalism)

    The agency has analyzed this proposal in accordance with the 
principles and criteria set forth in Executive Order 13132. This 
proposal would not have a substantial direct effects on the States, on 
the relationship between the national government and the States, or on 
the distribution of power and responsibilities among the various levels 
of government, as specified in Executive Order 13132.

C. Executive Order 13045

    Executive Order 13045 (62 FR 19885, April 23, 1997) applies to any 
rule that: (1) is determined to be ``economically significant'' as 
defined under E.O. 12866, and (2) concerns an environmental, health or 
safety risk that NHTSA has reason to believe may have a 
disproportionate effect on children. If the regulatory action meets 
both criteria, we must evaluate the environmental health or safety 
effects of the planned rule on children, and explain why the planned 
regulation is preferable to other potentially effective and reasonably 
feasible alternatives considered by us.
    This proposal is not subject to the Executive Order 13045 because 
it is not economically significant as defined in E.O. 12866 and does 
not involve decisions based on environmental, safety or health risks 
having a disproportionate impact on children.

D. Civil Justice Reform

    This final rule does not have any retroactive effect. Under 49 
U.S.C. 21403, whenever a Federal motor vehicle safety standard is in 
effect, a State may not adopt or maintain a safety standard applicable 
to the same aspect of performance which is not identical to the Federal 
standard, except to the extent that the state requirement imposes a 
higher level of performance and applies only to vehicles procured for 
the State's use. 49 U.S.C. 21461 sets forth a procedure for judicial 
review of final rules establishing, amending or revoking Federal motor 
vehicle safety standards. That section does not require submission of a 
petition for reconsideration or other administrative proceedings before 
parties may file suit in court.

E. Regulatory Flexibility Act

    The Regulatory Flexibility Act of 1980 (5 U.S.C. 601 et seq.) 
requires agencies to evaluate the potential effects of their proposed 
rules on small businesses, small organizations and small governmental 
jurisdictions. I have considered the possible effects of this 
rulemaking action under the Regulatory Flexibility Act and certify that 
it would not have a significant economic impact on a substantial number 
of small entities.
    This document proposes to amend and reorganize the regulatory text 
of 49 CFR 571.114 so that it better correlates to modern theft 
protection technology and better reflects the agency's interpretation 
of the existing requirements. If made final, vehicle manufacturers or 
any other small businesses would not have to make any changes to their 
products as a result of this rule.

F. Paperwork Reduction Act

    Under the Paperwork Reduction Act of 1995, a person is not required 
to respond to a collection of information by a Federal agency unless 
the collection displays a valid OMB control number. This proposal does 
not include any new information collection requirements.

G. National Technology Transfer and Advancement Act

    Section 12(d) of the National Technology Transfer and Advancement 
Act of 1995 (NTTAA), Public Law 104-113, section 12(d) (15 U.S.C. 272) 
directs us to use voluntary consensus standards in its regulatory 
activities unless doing so would be inconsistent with applicable law or 
otherwise impractical. Voluntary consensus standards are technical 
standards (e.g., materials specifications, test methods, sampling 
procedures, and business practices) that are developed or adopted by 
voluntary consensus standards bodies. The NTTAA directs us to provide 
Congress, through OMB, explanations when we decide not to use available 
and applicable voluntary consensus standards.
    There are no available voluntary consensus standards that are 
equivalent to FMVSS No. 114.

H. Unfunded Mandates Reform Act

    Section 202 of the Unfunded Mandates Reform Act of 1995 (UMRA) 
requires Federal agencies to prepare a written assessment of the costs, 
benefits and other effects of proposed or final rules that include a 
Federal mandate likely to result in the expenditure by State, local or 
tribal governments, in the aggregate, or by the private sector, of more 
than $100 million in any one year ($120.7 million as adjusted annually 
for inflation with base year of 1995).
    The proposed requirements would not result in costs of $120.7 
million or more to either State, local, or tribal governments, in the 
aggregate, or to the private sector.

I. Regulation Identifier Number (RIN)

    The Department of Transportation assigns a regulation identifier 
number (RIN) to each regulatory action listed in the Unified Agenda of 
Federal Regulations. The Regulatory Information Service Center 
publishes the Unified Agenda in April and October of each year. You may 
use the RIN contained in the heading at the beginning of this document 
to find this action in the Unified Agenda.

J. Privacy Act

    Please note that anyone is able to search the electronic form of 
all comments received into any of our dockets by the name of the 
individual submitting the comment (or signing the comment, if submitted 
on behalf of an association, business, labor union, etc.). You may 
review DOT's complete Privacy Act Statement in the Federal Register 
published on April 11, 2000 (Volume 65, Number 70; Pages 19477-78), or 
you may visit http://dms.dot.gov.

K. Plain Language

    Executive Order 12866 requires each agency to write all rules in 
plain language. Application of the principles of plain language 
includes consideration of the following questions:
     Have we organized the material to suit the public's needs?
     Are the requirements in the rule clearly stated?
     Does the rule contain technical language or jargon that 
isn't clear?
     Would a different format (grouping and order of sections, 
use of headings, paragraphing) make the rule easier to understand?
     Would more (but shorter) sections be better?
     Could we improve clarity by adding tables, lists, or 
diagrams?
     What else could we do to make the rule easier to 
understand?
    If you have any responses to these questions, please include them 
in your comments on this proposal.

L. National Environmental Policy Act

    NHTSA has analyzed this proposal for the purposes of the National 
Environmental Policy Act. The agency has determined that implementation 
of this action would not have any

[[Page 48367]]

significant impact on the quality of the human environment.

VI. Regulatory Text

List of Subjects in 49 CFR Parts 571

    Motor vehicle safety, Reporting and recordkeeping requirements, 
Tires.
    In consideration of the foregoing, part 571 would be amended as 
follows:

PART 571--[AMENDED]

    1. The authority citation for part 571 would continue to read as 
follows:

    Authority: 49 U.S.C. 322, 2011, 30115, 30166 and 30177; 
delegation of authority at 49 CFR 1.50.

    2. Section 571.114 would be revised to read as follows:


Sec.  571.114  Standard No. 114; Theft protection and rollaway 
prevention.

    S1. Scope. This standard specifies vehicle performance requirements 
intended to reduce the incidence of crashes resulting from theft and 
accidental rollaway of motor vehicles.
    S2. Purpose. The purpose of this standard is to decrease the 
likelihood that a vehicle is stolen, or accidentally set in motion.
    S3. Application. This standard applies to all passenger cars, and 
to trucks and multipurpose passenger vehicles with a GVWR of 4,536 
kilograms (10,000 pounds) or less. However, it does not apply to walk-
in van-type vehicles.

S4. Definitions

    Combination means a variation of the key that permits the starting 
system of a particular vehicle to be operated.
    Key means a physical device or an electronic code which, when 
inserted into the starting system (by physical or electronic means), 
enables the vehicle operator to activate the engine or motor.
    Open-body type vehicle means a vehicle having no occupant 
compartment doors or vehicle having readily detachable occupant 
compartment doors.
    Starting system means the vehicle system used in conjunction with 
the key to activate the engine or motor.
    Vehicle type, as used in S5.1.2, refers to passenger car, truck, or 
multipurpose passenger vehicle, as those terms are defined in 49 CFR 
571.3.
    S5. Requirements. Each vehicle subject to this standard must meet 
the requirements of S5.1 and S5.2. Open-body type vehicles are not 
required to comply with S5.1.3.

S5.1 Theft Protection

    S5.1.1 Each vehicle must have a starting system which, whenever the 
key is removed from the starting system prevents:
    (a) The normal activation of the vehicle's engine or motor; and
    (b) Either steering, or forward self-mobility, of the vehicle, or 
both.
    S5.1.2 For each vehicle type manufactured by a manufacturer, the 
manufacturer must provide at least 1,000 unique key combinations, or a 
number equal to the total number of the vehicles of that type 
manufactured by the manufacturer, whichever is less. The same 
combinations may be used for more than one vehicle type.
    S5.1.3. Except as specified below, an audible warning to the 
vehicle operator must be activated whenever the key is in the starting 
system and the door located closest to the driver's designated seating 
position is opened. An audible warning to the vehicle operator need not 
activate:
    (a) After the key has been inserted into the starting system, and 
before the driver takes further action; or
    (b) If the key is in the starting system in a manner or position 
that allows the engine or motor to be started or to continue operating; 
or
    (c) For mechanical keys and starting systems, after the key has 
been withdrawn to a position from which it may not be turned.
    S5.1.4. If a vehicle is equipped with a transmission with a 
``park'' position, the means for deactivating the vehicle's engine or 
motor must not activate any device installed pursuant to S5.1.1(b), 
unless the transmission is locked in the ``park'' position.

S5.2. Rollaway Prevention in Vehicles Equipped With Transmissions With 
a ``Park'' Position

    S5.2.1 Except as specified in S5.2.3, the starting system required 
by S5.1 must prevent key removal when tested according to the 
procedures in S6, unless the transmission or gear selection control is 
locked in ``park'' or becomes locked in ``park'' as a direct result of 
key removal.
    S5.2.2 Except as specified in S5.2.4, the vehicle must be designed 
such that the transmission or gear selection control cannot move from 
the ``park'' position, unless the key is in the starting system.

S5.2.3 Key Removal Override Option

    At the option of the manufacturer, the key may be removed from the 
starting system without the transmission or gear selection control in 
the ``park'' position under one of the following conditions:
    (a) In the event of electrical failure, including battery 
discharge, the key may be automatically removed from the starting 
system without the transmission or gear selection control locked in the 
``park'' position; or
    (b) Provided that steering or self-mobility is prevented, the 
vehicle may have a device by which the user can remove the key from the 
starting system without the transmission or gear selection control 
locked in ``park.'' This device must require:
    (i) The use of a tool, and
    (ii) Simultaneous activation of the device and removal of the key; 
or
    (c) Provided that steering or self-mobility is prevented, the 
vehicle may have a device by which the user can remove the key from the 
starting system without the transmission or gear selection control 
locked in ``park.'' This device must be covered by an opaque surface 
which, when installed:
    (i) Prevents sight of and use of the device, and
    (ii) Can be removed only by using a screwdriver or other tool.

S5.2.4 Gear Selection Control Override Option

    The vehicle may have a device by which the user can move the gear 
selection control from ``park'' after the key has been removed from the 
starting system. This device must be operable by one of the three 
options below:
    (a) By use of the key; or
    (b) By a means other than the key, provided steering or forward 
self-mobility is prevented when the key is removed from the starting 
system. Such a means must require:
    (i) The use of a tool, and
    (ii) Simultaneous activation of this means and movement of the gear 
selection control from ``park;'' or
    (c) By a means other than the key, provided steering or forward 
self-mobility is prevented when the key is removed from the starting 
system. This device must be covered by an opaque surface which, when 
installed:
    (i) Prevents sight of and use of the device, and
    (ii) Can be removed only by using a screwdriver or other tool.
    S5.2.5 When tested in accordance with S6.2.2, each vehicle must not 
move more than 150 mm on a 10 percent grade when the gear selection 
control is locked in ``park.''

S6. Compliance Test Procedure for Vehicles With Transmissions With a 
``Park'' Position

S6.1 Test Conditions

    S6.1.1 The vehicle shall be tested at curb weight plus 91 kg 
(including the driver).
    S6.1.2 Except where specified otherwise, the test surface shall be 
level.

[[Page 48368]]

S6.2 Test Procedure

S6.2.1
    (a) Activate the starting system using the key.
    (b) Move the gear selection control to any gear selection position 
or any other position where it will remain without assistance, 
including a position between any detent positions, except for the 
``park'' position.
    (c) Attempt to remove the key in each gear selection position.
S6.2.2
    (a) Drive the vehicle forward up a 10 percent grade and stop it 
with the service brakes.
    (b) Apply the parking brake (if present).
    (c) Move the gear selection control to ``park.''
    (d) Note the vehicle position.
    (e) Release the parking brake. Release the service brakes.
    (f) Remove the key.
    (g) Verify that the gear selection control or transmission is 
locked in ``park.''
    (h) Verify that the vehicle, at rest, has moved no more than 150 mm 
from the position noted prior to release of the brakes.
S6.2.3
    (a) Drive the vehicle forward down a 10 percent grade and stop it 
with the service brakes.
    (b) Apply the parking brake (if present).
    (c) Move the gear selection control to ``park.''
    (d) Note the vehicle position.
    (e) Release the parking brake. Release the service brakes.
    (f) Remove the key.
    (g) Verify that the gear selection control or transmission is 
locked in ``park.''
    (h) Verify that the vehicle, at rest, has moved no more than 150 mm 
from the position noted prior to release of the brakes.

    Issued: August 5, 2005.
Stephen R. Kratzke,
Associate Administrator for Rulemaking.
[FR Doc. 05-16226 Filed 8-16-05; 8:45 am]
BILLING CODE 4910-59-P