[Federal Register Volume 70, Number 25 (Tuesday, February 8, 2005)]
[Notices]
[Pages 6620-6622]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: E5-514]


-----------------------------------------------------------------------

DEPARTMENT OF COMMERCE

International Trade Administration

[A-201-822]


Certain Stainless Steel Sheet and Strip in Coils from Mexico: 
Final Results of the Full Sunset Review of Antidumping Duty Order

AGENCY: Import Administration, International Trade Administration, 
Department of Commerce.
SUMMARY: On November 17, 2004, the Department of Commerce (``the 
Department'') published a notice of preliminary results of the full 
sunset review of the antidumping duty order on certain stainless steel 
sheet and strip in coils (``SSSS'') from Mexico pursuant to section 
751(c) of the Tariff Act of 1930, as amended (``the Act''). We provided 
interested parties an opportunity to comment on our preliminary 
results. We received case and rebuttal briefs from domestic and 
respondent interested parties. No hearing was requested by parties. As 
a result of this review, the Department finds that revocation of this 
order would be likely to lead to continuation or recurrence of dumping.

EFFECTIVE DATE: February 8, 2005.

[[Page 6621]]


FOR FURTHER INFORMATION CONTACT: Martha V. Douthit, Office of Policy, 
Import Administration, International Trade Administration, U.S. 
Department of Commerce, 14th Street & Constitution Avenue, NW, 
Washington, DC , 20230; telephone: 202-482-5050.

SUPPLEMENTARY INFORMATION:

Scope of the Order

    See Appendix 1

Background

    On November 17, 2004, the Department of Commerce (the 
``Department'') published in the Federal Register a notice of 
preliminary results of the full sunset review of the antidumping duty 
order on SSSS from Mexico, pursuant to section 751(c) of the Tariff Act 
of 1930, as amended (``the Act''). See Certain Stainless Steel Sheet 
and Strip in Coils from Mexico; Preliminary Results of the Sunset 
Review of Antidumping Duty Order, 69 FR 67309 (November 17, 2004) 
(``Preliminary Results''). In our preliminary results, we determined 
that revocation of the order would likely result in continuation or 
recurrence of dumping with a margin of 30.85 percent for Mexinox S.A. 
de C.V. and ``all others'' the margin determined in the original 
investigation.
    On January 3, 2005, respondent, ThyssenKrupp Mexinox S.A. de C.V. 
and Mexinox USA, Inc. (collectively ``Mexinox''), submitted its case 
brief in response to the Department's preliminary results. On January 
7, 2005, Allegheny Ludlum Corporation, North American Stainless, Local 
3303 United Auto Workers, the United Steelworkers of America, AFL-CIO/
CLC, and the Zanesville Armco Independent Organization, Inc., 
(collectively ``domestic interested parties'') submitted rebuttal 
comments. No hearing was requested by parties.

Analysis of Comments Received

    All issues raised in the case and rebuttal briefs by parties to 
this sunset review are addressed in the ``Issues and Decision 
Memorandum'' (``Decision Memo'') from Ronald K. Lorentzen, Office of 
Policy, Import Administration, to Joseph A. Spetrini, Acting Assistant 
Secretary for Import Administration, dated January 27, 2005, which is 
hereby adopted and incorporated by reference into this notice. The 
issues discussed in the attached Decision Memo include the likelihood 
of continuation or recurrence of dumping and the magnitude of the 
margin likely to prevail were the order revoked. Parties can find a 
complete discussion of all issues raised in this review and the 
corresponding recommendations in this public memorandum, which is on 
file in the Central Records Unit, room B-099, of the main Commerce 
Building.
    In addition, a complete version of the Decision Memo can be 
accessed directly on the Web at www.ita.doc.gov/import_admin/records/frn/ under the heading ``Mexico.'' The paper copy and electronic 
version of the Decision Memo are identical in content.

Final Results of Review

    We determine that revocation of the antidumping duty order on SSSS 
from Mexico would be likely to lead to continuation or recurrence of 
dumping at the following weighted-average margins:

------------------------------------------------------------------------
                Manufacturer/Exporter                  Margin (percent)
------------------------------------------------------------------------
Mexinox.............................................               30.85
All Others..........................................               30.85
------------------------------------------------------------------------

    This five-year (``sunset'') review and notice are in accordance 
with sections 751(c), 752, and 777(i)(1) of the Act. This notice serves 
as the only reminder to parties subject to
    administrative protective order (``APO'') of their responsibility 
concerning the disposition of proprietary disclosed under APO in 
accordance with 19 CFR 351.305 of the Department's regulations. Timely 
notification of return/destruction of APO materials or conversion to 
judicial protective order is hereby requested. Failure to comply with 
the regulations and the terms of an APO is a sanctionable violation.

APPENDIX 1

STAINLESS STEEL AND SHEET AND STRIP IN COILS FROM MEXICO.

SCOPE OF THE ORDER (A-201-822)

    For purposes of this sunset review, the products covered are 
certain stainless steel sheet and strip in coils. Stainless steel is an 
alloy steel containing, by weight, 1.2 percent or less of carbon and 
10.5 percent or more of chromium, with or without other elements. The 
subject sheet and strip is a flat-rolled product in coils that is 
greater than 9.5 mm in width and less than 4.75 mm in thickness, and 
that is annealed or otherwise heat treated and pickled or otherwise 
descaled. The subject sheet and strip may also be further processed 
(e.g., cold-rolled, polished, aluminized, coated, etc.) provided that 
it maintains the specific dimensions of sheet and strip following such 
processing.
    The merchandise subject to this review is classified in the 
Harmonized Tariff Schedule of the United States (``HTS'') at 
subheadings: 7219.13.0031, 7219.13.0051, 7219.13.0071, 7219.1300.81, 
7219.14.0030, 7219.14.0065, 7219.14.0090, 7219.32.0005, 7219.32.0020, 
7219.32.0025, 7219.32.0035, 7219.32.0036, 7219.32.0038, 7219.32.0042, 
7219.32.0044, 7219.33.0005, 7219.33.0020, 7219.33.0025, 7219.33.0035, 
7219.33.0036, 7219.33.0038, 7219.33.0042, 7219.33.0044, 7219.34.0005, 
7219.34.0020, 7219.34.0025, 7219.34.0030, 7219.34.0035, 7219.35.0005, 
7219.35.0015, 7219.35.0030, 7219.35.0035, 7219.90.0010, 7219.90.0020, 
7219.90.0025, 7219.90.0060, 7219.90.0080, 7220.12.1000, 7220.12.5000, 
7220.20.1010, 7220.20.1015, 7220.20.1060, 7220.20.1080, 7220.20.6005, 
7220.20.6010, 7220.20.6015, 7220.20.6060, 7220.20.6080, 7220.20.7005, 
7220.20.7010, 7220.20.7015, 7220.20.7060, 7220.20.7080, 7220.20.8000, 
7220.20.9030, 7220.20.9060, 7220.90.0010, 7220.90.0015, 7220.90.0060, 
and 7220.90.0080. Although the HTS subheadings are provided for 
convenience and customs purposes, the Department's written description 
of the merchandise under review is dispositive.
    Excluded from the scope of this review are the following: (1) Sheet 
and strip that is not annealed or otherwise heat treated and pickled or 
otherwise descaled, (2) sheet and strip that is cut to length, (3) 
plate (i.e., flat-rolled stainless steel products of a thickness of 
4.75 mm or more), (4) flat wire (i.e., cold-rolled sections, with a 
prepared edge, rectangular in shape, of a width of not more than 9.5 
mm), and (5) razor blade steel. Razor blade steel is a flat-rolled 
product of stainless steel, not further worked than cold-rolled (cold-
reduced), in coils, of a width of not more than 23 mm and a thickness 
of 0.266 mm or less, containing, by weight, 12.5 to 14.5 percent 
chromium, and certified at the time of entry to be used in the 
manufacture of razor blades.\1\
---------------------------------------------------------------------------

    \1\ See Chapter 72 of the HTS, ``Additional U.S. Note'' 1(d).
---------------------------------------------------------------------------

    In response to comments by interested parties, the Department has 
determined that certain specialty stainless steel products are also 
excluded from the scope of this review. These excluded products are 
described below.
    Flapper valve steel is defined as stainless steel strip in coils 
containing, by weight, between 0.37 and 0.43 percent carbon, between 
1.15 and 1.35

[[Page 6622]]

percent molybdenum, and between 0.20 and 0.80 percent manganese. This 
steel also contains, by weight, phosphorus of 0.025 percent or less, 
silicon of between 0.20 and 0.50 percent, and sulfur of 0.020 percent 
or less. The product is manufactured by means of vacuum arc remelting, 
with inclusion controls for sulphide of no more than 0.04 percent and 
for oxide of no more than 0.05 percent. Flapper valve steel has a 
tensile strength of between 210 and 300 ksi, yield strength of between 
170 and 270 ksi, plus or minus 8 ksi, and a hardness (Hv) of between 
460 and 590. Flapper valve steel is most commonly used to produce 
specialty flapper valves in compressors.
    Also excluded is a product referred to as suspension foil, a 
specialty steel product used in the manufacture of suspension 
assemblies for computer disk drives. Suspension foil is described as 
302/304 grade or 202 grade stainless steel of a thickness between 14 
and 127 microns, with a thickness tolerance of plus-or-minus 2.01 
microns, and surface glossiness of 200 to 700 percent Gs. Suspension 
foil must be supplied in coil widths of not more than 407 mm, and with 
a mass of 225 kg or less. Roll marks may only be visible on one side, 
with no scratches of measurable depth. The material must exhibit 
residual stresses of 2 mm maximum deflection, and flatness of 1.6 mm 
over 685 mm length.
    Certain stainless steel foil for automotive catalytic converters is 
also excluded from the scope of this review. This stainless steel strip 
in coils is a specialty foil with a thickness of between 20 and 110 
microns used to produce a metallic substrate with a honeycomb structure 
for use in automotive catalytic converters. The steel contains, by 
weight, carbon of no more than 0.030 percent, silicon of no more than 
1.0 percent, manganese of no more than 1.0 percent, chromium of between 
19 and 22 percent, aluminum of no less than 5.0 percent, phosphorus of 
no more than 0.045 percent, sulfur of no more than 0.03 percent, 
lanthanum of less than 0.002 or greater than 0.05 percent, and total 
rare earth elements of more than 0.06 percent, with the balance iron.
    Permanent magnet iron-chromium-cobalt alloy stainless strip is also 
excluded from the scope of this review. This ductile stainless steel 
strip contains, by weight, 26 to 30 percent chromium, and 7 to 10 
percent cobalt, with the remainder of iron, in widths 228.6 mm or less, 
and a thickness between 0.127 and 1.270 mm. It exhibits magnetic 
remanence between 9,000 and 12,000 gauss, and a coercivity of between 
50 and 300 oersteds. This product is most commonly used in electronic 
sensors and is currently available under proprietary trade names such 
as ``Arnokrome III.''\2\
---------------------------------------------------------------------------

    \2\ ``Arnokrome III'' is a trademark of the Arnold Engineering 
Company.
---------------------------------------------------------------------------

    Certain electrical resistance alloy steel is also excluded from the 
scope of this review. This product is defined as a non-magnetic 
stainless steel manufactured to American Society of Testing and 
Materials (``ASTM'') specification B344 and containing, by weight, 36 
percent nickel, 18 percent chromium, and 46 percent iron, and is most 
notable for its resistance to high temperature corrosion. It has a 
melting point of 1390 degrees Celsius and displays a creep rupture 
limit of 4 kilograms per square millimeter at 1000 degrees Celsius. 
This steel is most commonly used in the production of heating ribbons 
for circuit breakers and industrial furnaces, and in rheostats for 
railway locomotives. The product is currently available under 
proprietary trade names such as ``Gilphy 36.''\3\
---------------------------------------------------------------------------

    \3\ ``Gilphy 36'' is a trademark of Imphy, S.A.
---------------------------------------------------------------------------

    Certain martensitic precipitation-hardenable stainless steel is 
also excluded from the scope of this review. This high-strength, 
ductile stainless steel product is designated under the Unified 
Numbering System (``UNS'') as S45500- grade steel, and contains, by 
weight, 11 to 13 percent chromium, and 7 to 10 percent nickel. Carbon, 
manganese, silicon and molybdenum each comprise, by weight, 0.05 
percent or less, with phosphorus and sulfur each comprising, by weight, 
0.03 percent or less. This steel has copper, niobium, and titanium 
added to achieve aging, and will exhibit yield strengths as high as 
1700 Mpa and ultimate tensile strengths as high as 1750 Mpa after 
aging, with elongation percentages of 3 percent or less in 50 mm. It is 
generally provided in thicknesses between 0.635 and 0.787 mm, and in 
widths of 25.4 mm. This product is most commonly used in the 
manufacture of television tubes and is currently available under 
proprietary trade names such as ``Durphynox 17.''\4\
---------------------------------------------------------------------------

    \4\ ``Durphynox 17'' is a trademark of Imphy, S.A.
---------------------------------------------------------------------------

    Finally, three specialty stainless steels typically used in certain 
industrial blades and surgical and medical instruments are also 
excluded from the scope of this review. These include stainless steel 
strip in coils used in the production of textile cutting tools (e.g., 
carpet knives).\5\ This steel is similar to AISI grade 420 but 
containing, by weight, 0.5 to 0.7 percent of molybdenum. The steel also 
contains, by weight, carbon of between 1.0 and 1.1 percent, sulfur of 
0.020 percent or less, and includes between 0.20 and 0.30 percent 
copper and between 0.20 and 0.50 percent cobalt. This steel is sold 
under proprietary names such as ``GIN4 Mo.'' The second excluded 
stainless steel strip in coils is similar to AISI 420-J2 and contains, 
by weight, carbon of between 0.62 and 0.70 percent, silicon of between 
0.20 and 0.50 percent, manganese of between 0.45 and 0.80 percent, 
phosphorus of no more than 0.025 percent and sulfur of no more than 
0.020 percent. This steel has a carbide density on average of 100 
carbide particles per 100 square microns. An example of this product is 
``GIN5'' steel. The third specialty steel has a chemical composition 
similar to AISI 420 F, with carbon of between 0.37 and 0.43 percent, 
molybdenum of between 1.15 and 1.35 percent, but lower manganese of 
between 0.20 and 0.80 percent, phosphorus of no more than 0.025 
percent, silicon of between 0.20 and 0.50 percent, and sulfur of no 
more than 0.020 percent. This product is supplied with a hardness of 
more than Hv 500 guaranteed after customer processing, and is supplied 
as, for example, ``GIN6''.\6\
---------------------------------------------------------------------------

    \5\ This list of uses is illustrative and provided for 
descriptive purposes only.
    \6\ ``GIN4 Mo,'' ``GIN5'' and ``GIN6'' are the proprietary 
grades of Hitachi Metals America, Ltd.

    Dated: January 27, 2005.
Joseph A. Spetrini,
Acting Deputy Assistant Secretary for Import Administration.
[FR Doc. E5-514 Filed 2-7-05; 8:45 am]
BILLING CODE 3510-DS-S