[Federal Register Volume 67, Number 208 (Monday, October 28, 2002)]
[Notices]
[Pages 65783-65786]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 02-27394]


-----------------------------------------------------------------------

DEPARTMENT OF COMMERCE

International Trade Administration

[A-588-854]


Certain Tin Mill Products From Japan: Notice of Initiation of 
Changed Circumstances Review of the Antidumping Order

AGENCY: Import Administration, International Trade Administration, 
Department of Commerce.

ACTION: Notice of initiation of changed circumstances antidumping duty 
review.

-----------------------------------------------------------------------

SUMMARY: In accordance with 19 CFR 351.216(b), Nippon Steel Corporation 
(''Nippon''), an exporter and manufacturer of the subject merchandise, 
filed a request for a changed circumstances review of the antidumping 
order on certain tin mill products from Japan with respect to certain 
laminated tin-free steel, as described below. In Nippon's request, 
Weirton Steel Corporation, United States Steel Corporation, Bethlehem 
Steel Corporation, USS-Posco Industries, and National Steel Corporation 
stated that they do not object to the exclusion of this product

[[Page 65784]]

from the order. In response to the apparent lack of interest in this 
product from the domestic industry, the Department of Commerce (``the 
Department'') is initiating a changed circumstances review with respect 
to this request for all future entries for consumption of tin-free 
laminated steel, as described below.

EFFECTIVE DATE: October 28, 2002.

FOR FURTHER INFORMATION CONTACT: Michael Ferrier, Import 
Administration, International Trade Administration, U.S. Department of 
Commerce, 14th Street and Constitution Avenue, NW., Washington, DC 
20230; telephone: (202) 482-1394.

The Applicable Statute and Regulations

    Unless otherwise indicated, all citations to the statute are 
references to the provisions effective January 1, 1995, the effective 
date of the amendments made to the Tariff Act of 1930, as amended 
(``the Act''), by the Uruguay Round Agreements Act. In addition, unless 
otherwise indicated, all citations to the Department's regulations are 
to the regulations as codified at 19 CFR part 351 (2002).

SUPPLEMENTARY INFORMATION:

Background

    On August 28, 2000, the Department published in the Federal 
Register the antidumping duty order on certain tin mill products from 
Japan. See Notice of Antidumping Duty Order: Certain Tin Mill Products 
from Japan 65 FR 52067 (August 28, 2000). On September 6, 2002, Nippon, 
an exporter and manufacturer of the subject merchandise requested that 
the Department revoke in part the antidumping duty order on certain tin 
mill products from Japan. Specifically, Nippon requested that the 
Department revoke the order with respect to imports meeting the 
following specifications: Tin-free steel laminated on one or both sides 
of the surface with a polyester film, consisting of two layers (an 
amorphous layer and an outer crystal layer), that contains no more than 
the indicated amounts of the following environmental hormones: 1 mg/kg 
BADGE (BisPhenol--A Di-glycidyl Ether), 1 mg/kg BFDGE (BisPhenol--F Di-
glycidyl Ether), and 3 mg/kg BPA (BisPhenol--A).
    Nippon included letters from Weirton Steel Corporation, United 
States
    Steel Corporation, Bethlehem Steel Corporation, USS-Posco 
Industries, and
    National Steel Corporation, in its request for the changed 
circumstances review stating their support for the exclusion of the 
tin-free laminated steel, as described above. However, the Department 
does not have information on the record of this changed circumstances 
review that the aforementioned domestic tin mill producers account for 
substantially all, or at least 85 percent, of the production of the 
domestic like product. See Oil Country Tubular Goods From Mexico: 
Preliminary Results of Changed Circumstances Antidumping Duty 
Administrative Review, 64 FR 14213 (March 24, 1999). Additionally, the 
Department has no information on the record that the other known 
domestic producers of tin mill products, Wheeling-Pittsburgh Steel 
Corporation, and Ohio Coatings Corporation, have no interest in 
maintaining the antidumping duty order with respect to certain 
laminated tin-free steel described in Nippon's request. Therefore, we 
are not combining this initiation with a preliminary determination, 
which is our normal practice under section 351.221(c)(3)(ii). This 
notice of initiation will accord all interested parties an opportunity 
to address this proposed exclusion.

Scope of Review

    The products covered by this antidumping order are tin mill flat-
rolled products that are coated or plated with tin, chromium or 
chromium oxides. Flat-rolled steel products coated with tin are known 
as tin plate. Flat-rolled steel products coated with chromium or 
chromium oxides are known as tin-free steel or electrolytic chromium-
coated steel. The scope includes all the noted tin mill products 
regardless of thickness, width, form (in coils or cut sheets), coating 
type (electrolytic or otherwise), edge (trimmed, untrimmed or further 
processed, such and scroll cut), coating thickness, surface finish, 
temper, coating metal (tin, chromium, chromium oxide), reduction 
(single- or double-reduced), and whether or not coated with a plastic 
material. All products that meet the written physical description are 
within the scope of this order unless specifically excluded. The 
following products, by way of example, are outside and/or specifically 
excluded from the scope of this order:

--Single reduced electrolytically chromium coated steel with a 
thickness 0.238 mm (85 pound base box) (10%) or 0.251 mm (90 
pound base box) (10%) or 0.255 mm (10%) with 770 mm 
(minimum width) (1.588 mm) by 900 mm (maximum length if 
sheared) sheet size or 30.6875 inches (minimum width) ( \1/16\ 
inch) and 35.4 inches (maximum length if sheared) sheet size; with type 
MR or higher (per ASTM) A623 steel chemistry; batch annealed at T2 \1/
2\ anneal temper, with a yield strength of 31 to 42 kpsi (214 to 290 
Mpa); with a tensile strength of 43 to 58 kpsi (296 to 400 Mpa); with a 
chrome coating restricted to 32 to 150 mg/m\2\; with a chrome oxide 
coating restricted to 6 to 25 mg/m\2\ with a modified 7B ground roll 
finish or blasted roll finish; with roughness average (Ra) 0.10 to 0.35 
micrometers, measured with a stylus instrument with a stylus radius of 
2 to 5 microns, a trace length of 5.6 mm, and a cut-off of 0.8 mm, and 
the measurement traces shall be made perpendicular to the rolling 
direction; with an oil level of 0.17 to 0.37 grams/base box as type 
BSO, or 2.5 to 5.5 mg/m\2\ as type DOS, or 3.5 to 6.5 mg/m\2\ as type 
ATBC; with electrical conductivity of static probe voltage drop of 0.46 
volts drop maximum, and with electrical conductivity degradation to 
0.70 volts drop maximum after stoving (heating to 400 degrees F for 100 
minutes followed by a cool to room temperature).
--Single reduced electrolytically chromium- or tin-coated steel in the 
gauges of 0.0040 inch nominal, 0.0045 inch nominal, 0.0050 inch 
nominal, 0.0061 inch nominal (55 pound base box weight), 0.0066 inch 
nominal (60 pound base box weight), and 0.0072 inch nominal (65 pound 
base box weight), regardless of width, temper, finish, coating or other 
properties.
--Single reduced electrolytically chromium coated steel in the gauge of 
0.024 inch, with widths of 27.0 inches or 31.5 inches, and with T-1 
temper properties.
--Single reduced electrolytically chromium coated steel, with a 
chemical composition of 0.005% max carbon, 0.030% max silicon, 0.25% 
max manganese, 0.025% max phosphorous, 0.025% max sulfur, 0.070% max 
aluminum, and the balance iron, with a metallic chromium layer of 70-
130 mg/m\2\, with a chromium oxide layer of 5-30 mg/m\2\, with a 
tensile strength of 260-440 N/mm\2\, with an elongation of 28-48%, with 
a hardness (HR-30T) of 40-58, with a surface roughness of 0.5-1.5 
microns Ra, with magnetic properties of Bm (KG)10.0 minimum, Br (KG) 
8.0 minimum, Hc (Oe) 2.5-3.8, and MU 1400 minimum, as measured with a 
Riken Denshi DC magnetic characteristic measuring machine, Model BHU-
60.
--Bright finish tin-coated sheet with a thickness equal to or exceeding 
0.0299 inch, coated to thickness of \3/4\

[[Page 65785]]

pound (0.000045 inch) and 1 pound (0.00006 inch).
--Electrolytically chromium coated steel having ultra flat shape 
defined as oil can maximum depth of \5/64\ inch (2.0 mm) and edge wave 
maximum of \5/64\ inch (2.0 mm) and no wave to penetrate more than 2.0 
inches (51.0 mm) from the strip edge and coilset or curling 
requirements of average maximum of \5/64\ inch (2.0 mm) (based on six 
readings, three across each cut edge of a 24 inches (61 cm) long sample 
with no single reading exceeding \4/32\ inch (3.2 mm) and no more than 
two readings at \4/32\ inch (3.2 mm)) and (for 85 pound base box item 
only: crossbuckle maximums of 0.001 inch (0.0025 mm) average having no 
reading above 0.005 inch (0.127 mm)), with a camber maximum of \1/4\ 
inch (6.3 mm) per 20 feet (6.1 meters), capable of being bent 120 
degrees on a 0.002 inch radius without cracking, with a chromium 
coating weight of metallic chromium at 100 mg/m\2\ and chromium oxide 
of 10 mg/m\2\, with a chemistry of 0.13% maximum carbon, 0.60% maximum 
manganese, 0.15% maximum silicon, 0.20% maximum copper, 0.04% maximum 
phosphorous, 0.05% maximum sulfur, and 0.20% maximum aluminum, with a 
surface finish of Stone Finish 7C, with a DOS-A oil at an aim level of 
2 mg/square meter, with not more than 15 inclusions/foreign matter in 
15 feet (4.6 meters) (with inclusions not to exceed \1/32\ inch (0.8 
mm) in width and \3/64\ inch (1.2 mm) in length), with thickness/temper 
combinations of either 60 pound base box (0.0066 inch) double reduced 
CADR8 temper in widths of 25.00 inches, 27.00 inches, 27.50 inches, 
28.00 inches, 28.25 inches, 28.50 inches, 29.50 inches, 29.75 inches, 
30.25 inches, 31.00 inches, 32.75 inches, 33.75 inches, 35.75 inches, 
36.25 inches, 39.00 inches, or 43.00 inches, or 85 pound base box 
(0.0094 inch) single reduced CAT4 temper in widths of 25.00 inches, 
27.00 inches, 28.00 inches, 30.00 inches, 33.00 inches, 33.75 inches, 
35.75 inches, 36.25 inches, or 43.00 inches, with width tolerance of 
 \1/8\ inch, with a thickness tolerance of 0.0005 
inch, with a maximum coil weight of 20,000 pounds (9071.0 kg), with a 
minimum coil weight of 18,000 pounds (8164.8 kg) with a coil inside 
diameter of 16 inches (40.64 cm) with a steel core, with a coil maximum 
outside diameter of 59.5 inches (151.13 cm), with a maximum of one weld 
(identified with a paper flag) per coil, with a surface free of 
scratches, holes, and rust.
--Electrolytically tin coated steel having differential coating with 
1.00 pound/base box equivalent on the heavy side, with varied coating 
equivalents in the lighter side (detailed below), with a continuous 
cast steel chemistry of type MR, with a surface finish of type 7B or 
7C, with a surface passivation of 0.7 mg/square foot of chromium 
applied as a cathodic dichromate treatment, with coil form having 
restricted oil film weights of 0.3-0.4 grams/base box of type DOS-A 
oil, coil inside diameter ranging from 15.5 to 17 inches, coil outside 
diameter of a maximum 64 inches, with a maximum coil weight of 25,000 
pounds, and with temper/coating/dimension combinations of : (1) CAT 4 
temper, 1.00/.050 pound/base box coating, 70 pound/base box (0.0077 
inch) thickness, and 33.1875 inch ordered width; or (2) CAT5 temper, 
1.00/0.50 pound/base box coating, 75 pound/base box (0.0082 inch) 
thickness, and 34.9375 inch or 34.1875 inch ordered width; or (3) CAT5 
temper, 1.00/0.50 pound/base box coating, 107 pound/base box (0.0118 
inch) thickness, and 30.5625 inch or 35.5625 inch ordered width; or (4) 
CADR8 temper, 1.00/0.50 pound/base box coating, 85 pound/base box 
(0.0093 inch) thickness, and 35.5625 inch ordered width; or (5) CADR8 
temper, 1.00/0.25 pound/base box coating, 60 pound/base box (0.0066 
inch) thickness, and 35.9375 inch ordered width; or (6) CADR8 temper, 
1.00/0.25 pound/base box coating, 70 pound/base box (0.0077 inch) 
thickness, and 32.9375 inch, 33.125 inch, or 35.1875 inch ordered 
width.
--Electrolytically tin coated steel having differential coating with 
1.00 pound/base box equivalent on the heavy side, with varied coating 
equivalents on the lighter side (detailed below), with a continuous 
cast steel chemistry of type MR, with a surface finish of type 7B or 
7C, with a surface passivation of 0.5 mg/square foot of chromium 
applied as a cathodic dichromate treatment, with ultra flat scroll cut 
sheet form, with CAT 5 temper with 1.00/0.10 pound/base box coating, 
with a lithograph logo printed in a uniform pattern on the 0.10 pound 
coating side with a clear protective coat, with both sides waxed to a 
level of 15-20 mg/216 sq. in., with ordered dimension combinations of 
(1) 75 pound/base box (0.0082 inch) thickness and 34.9375 inch x 31.748 
inch scroll cut dimensions; or (2) 75 pound/base box (0.0082 inch) 
thickness and 34.1875 inch x 29.076 inch scroll cut dimensions; or (3) 
107 pound/base box (0.0118 inch) thickness and 30.5625 inch x 34.125 
inch scroll cut dimension.
--Tin-free steel coated with a metallic chromium layer between 100-200 
mg/m\2\ and a chromium oxide layer between 5-30 mg/m\2\; chemical 
composition of 0.05% maximum carbon, 0.03% maximum silicon, 0.60% 
maximum manganese, 0.02% maximum phosphorous, and 0.02% maximum sulfur; 
magnetic flux density (``Br'') of 10 kg minimum and a coercive force 
(``Hc'') of 3.8 Oe minimum.
    The merchandise subject to this order is classified in the 
Harmonized Tariff Schedule of the United States (``HTSUS''), under 
HTSUS subheadings 7210.11.0000, 7210.12.0000, 7210.50.0000, 
7212.10.0000, and 7212.50.0000 if of non-alloy steel and under HTSUS 
subheadings 7225.99.0090, and 7226.99.0000 if of alloy steel. Although 
the subheadings are provided for convenience and Customs purposes, our 
written description of the scope of this review is dispositive.

Initiation of Changed Circumstances Antidumping Duty Administrative 
Review

    Pursuant to section 751(d)(1) of the Act, the Department may revoke 
an antidumping or countervailing duty order, in whole or in part, based 
on a review under section 751(b) of the Act (i.e., a changed 
circumstances review). Section 751(b)(1) of the Act requires a changed 
circumstances review to be conducted upon receipt of a request which 
shows changed circumstances sufficient to warrant a review. Section 
351.222(g) of the Department's regulations provides that the Department 
will conduct a changed circumstances administrative review under 19 CFR 
351.216, and may revoke an order (in whole or in part), if it 
determines that (i) producers accounting for substantially all of the 
production of the domestic like product to which the order pertains 
have expressed a lack of interest in the relief provided by the order, 
in whole or in part, or (ii) if other changed circumstances sufficient 
to warrant revocation exist. To the Department's knowledge the 
following are U.S. producers of tin mill products: Bethlehem Steel 
Corporation, National Steel Corporation, Midwest Division, Ohio 
Coatings Corporation, U.S. Steel Group, a Unit of USX Corp., Wheeling-
Pittsburgh Steel Corporation, and USS-Posco Industries, Inc. Based upon 
the statements of no interest by Weirton

[[Page 65786]]

Steel Corporation, United States Steel Corporation, Bethlehem Steel 
Corporation, USS-Posco Industries, and National Steel Corporation, we 
believe there is information sufficient to warrant initiation of this 
changed circumstances review.
    The Department will publish in the Federal Register a notice of 
preliminary results of changed circumstances review, in accordance with 
19 CFR 351.221(c), which will set forth the factual and legal 
conclusions upon which our preliminary results are based, and a 
description of any action proposed based on those results. Interested 
parties may submit comments for consideration in the Department's 
preliminary results not later than 14 days after publication of this 
notice. Responses to those comments may be submitted not later than 7 
days following submission of the comments. All written comments must be 
submitted in accordance with 19 CFR 351.303, and must be served on all 
interested parties on the Department's service list in accordance with 
19 CFR 351.303. The Department will also issue its final results of 
review within 270 days after the date on which the changed 
circumstances review is initiated, in accordance with 19 CFR 
351.216(e), and will publish these results in the Federal Register. 
While the changed circumstances review is underway, the current 
requirement for a cash deposit of estimated antidumping duties on all 
subject merchandise, including the merchandise that is the subject of 
this changed circumstances review, will continue unless and until it is 
modified pursuant to the final results of this changed circumstances 
review or other administrative review.
    This notice is in accordance with sections 751(b)(1) and 777(i)(1) 
of the Act and 19 CFR 351.216 and 351.222.

    Dated: October 21, 2002.
Faryar Shirzad,
Assistant Secretary for Import Administration.
[FR Doc. 02-27394 Filed 10-25-02; 8:45 am]
BILLING CODE 3510-DS-P