[Federal Register Volume 67, Number 29 (Tuesday, February 12, 2002)]
[Notices]
[Pages 6493-6495]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 02-3386]


-----------------------------------------------------------------------

DEPARTMENT OF COMMERCE

International Trade Administration

[A-427-814]


Notice of Final Results of Antidumping Duty Administrative 
Review: Stainless Steel Sheet and Strip in Coils From France

AGENCY: Import Administration, International Trade Administration, 
Department of Commerce.

ACTION: Notice of final results of antidumping duty administrative 
review.

-----------------------------------------------------------------------

SUMMARY: On August 8, 2001, the Department of Commerce (``Department'') 
published the preliminary results of the administrative review of the 
antidumping duty order on stainless steel sheet and strip in coils from 
France. This review covers one manufacturer/exporter. The period of 
review (``POR'') is January 4, 1999 through June 30, 2000.
    Based on our analysis of the comments received, we have made 
changes in the margin calculations. Therefore, the final results differ 
from the preliminary results. The final weighted-average dumping 
margins for the reviewed firm is listed below in the section entitled 
``Final Results of the Review.''

EFFECTIVE DATE: February 12, 2002.

FOR FURTHER INFORMATION CONTACT: Robert Bolling or James Doyle, 
Enforcement Group III, Import Administration, International Trade 
Administration, U.S. Department of Commerce, 1401 Constitution Avenue, 
NW., Washington, DC 20230; telephone: 202-482-3434, or 202-482-0159, 
respectively.

SUPPLEMENTARY INFORMATION:

Applicable Statute

    Unless otherwise indicated, all citations to the Tariff Act of 
1930, as amended (``Act''), are references to the provisions effective 
January 1, 1995, the effective date of the amendments made to the Act 
by the Uruguay Round Agreements Act (``URAA''). In addition, unless 
otherwise indicated, all citations to the Department's regulations are 
to the regulations codified at 19 CFR part 351 (2001).

Scope of Review

    For purposes of this administrative review, the products covered 
are certain stainless steel sheet and strip in coils. Stainless steel 
is an alloy steel containing, by weight, 1.2 percent or less of carbon 
and 10.5 percent or more of chromium, with or without other elements. 
The subject sheet and strip is a flat-rolled product in coils that is 
greater than 9.5 mm in width and less than 4.75 mm in thickness, and 
that is annealed or otherwise heat treated and pickled or otherwise 
descaled. The subject sheet and strip may also be further processed 
(e.g., cold-rolled, polished, aluminized, coated, etc.) provided that 
it maintains the specific dimensions of sheet and strip following such 
processing.
    The merchandise subject to this order is currently classifiable in 
the Harmonized Tariff Schedule of the United States (``HTS'') at 
subheadings: 7219.13.0031, 7219.13.0051, 7219.13.0071, 7219.1300.81,\1\ 
7219.14.0030, 7219.14.0065, 7219.14.0090, 7219.32.0005, 7219.32.0020, 
7219.32.0025, 7219.32.0035, 7219.32.0036, 7219.32.0038, 7219.32.0042, 
7219.32.0044, 7219.33.0005, 7219.33.0020, 7219.33.0025, 7219.33.0035, 
7219.33.0036, 7219.33.0038, 7219.33.0042, 7219.33.0044, 7219.34.0005, 
7219.34.0020, 7219.34.0025, 7219.34.0030, 7219.34.0035, 7219.35.0005, 
7219.35.0015, 7219.35.0030, 7219.35.0035, 7219.90.0010, 7219.90.0020, 
7219.90.0025, 7219.90.0060, 7219.90.0080, 7220.12.1000, 7220.12.5000, 
7220.20.1010, 7220.20.1015, 7220.20.1060, 7220.20.1080, 7220.20.6005, 
7220.20.6010, 7220.20.6015, 7220.20.6060, 7220.20.6080, 7220.20.7005, 
7220.20.7010, 7220.20.7015, 7220.20.7060, 7220.20.7080, 7220.20.8000, 
7220.20.9030, 7220.20.9060, 7220.90.0010, 7220.90.0015, 7220.90.0060, 
and 7220.90.0080. Although the HTS subheadings are provided for 
convenience and Customs purposes, the Department's written description 
of the merchandise under review is dispositive.
---------------------------------------------------------------------------

    \1\ Due to changes to the HTS numbers in 2001, 7219.13.0030, 
7219.13.0050, 7219.13.0070, and 7219.13.0080 are now 7219.13.0031, 
7219.13.0051, 7219.13.0071, and 7219.13.0081, respectively.
---------------------------------------------------------------------------

    Excluded from the review of this order are the following: (1) Sheet 
and strip that is not annealed or otherwise heat treated and pickled or 
otherwise descaled, (2) sheet and strip that is cut to length, (3) 
plate (i.e., flat-rolled stainless steel products of a thickness of 
4.75 mm or more), (4) flat wire (i.e., cold-rolled sections, with a 
prepared edge, rectangular in shape, of a width of not more than 9.5 
mm), and (5) razor blade steel. Razor blade steel is a flat-rolled 
product of stainless steel, not further worked than cold-rolled (cold-
reduced), in coils, of a width of not more than 23 mm and a thickness 
of 0.266 mm or less, containing, by weight, 12.5 to 14.5 percent 
chromium, and certified at the time of entry to be used in the 
manufacture of razor blades. See Chapter 72 of the HTS, ``Additional 
U.S. Note'' 1(d).
    Flapper valve steel is also excluded from the scope of the order. 
This product is defined as stainless steel strip in coils containing, 
by weight, between 0.37 and 0.43 percent carbon, between 1.15 and 1.35 
percent molybdenum, and between 0.20 and 0.80 percent manganese. This 
steel also contains, by weight, phosphorus of 0.025 percent or less, 
silicon of between 0.20 and 0.50 percent, and sulfur of 0.020 percent 
or less. The product is manufactured by means of vacuum arc remelting, 
with inclusion controls for sulphide of no more than 0.04 percent and 
for oxide of no more than 0.05 percent. Flapper valve steel has a 
tensile strength of between 210 and 300 ksi, yield strength of between 
170 and 270 ksi, plus or minus 8 ksi, and a hardness (Hv) of between 
460 and 590. Flapper valve steel is most commonly used to produce 
specialty flapper valves in compressors.
    Also excluded is a product referred to as suspension foil, a 
specialty steel product used in the manufacture of suspension 
assemblies for computer disk drives. Suspension foil is described as 
302/304 grade or 202 grade stainless steel of a thickness between 14 
and 127 microns, with a thickness tolerance of plus-or-minus 2.01 
microns, and surface glossiness of 200 to 700 percent Gs. Suspension 
foil must be supplied in coil widths of not more than 407 mm, and with 
a mass of 225 kg or less. Roll marks may only be visible on one side, 
with no scratches of measurable depth. The material must exhibit 
residual stresses

[[Page 6494]]

of 2 mm maximum deflection, and flatness of 1.6 mm over 685 mm length.
    Certain stainless steel foil for automotive catalytic converters is 
also excluded from the scope of this order. This stainless steel strip 
in coils is a specialty foil with a thickness of between 20 and 110 
microns used to produce a metallic substrate with a honeycomb structure 
for use in automotive catalytic converters. The steel contains, by 
weight, carbon of no more than 0.030 percent, silicon of no more than 
1.0 percent, manganese of no more than 1.0 percent, chromium of between 
19 and 22 percent, aluminum of no less than 5.0 percent, phosphorus of 
no more than 0.045 percent, sulfur of no more than 0.03 percent, 
lanthanum of less than 0.002 or greater than 0.05 percent, and total 
rare earth elements of more than 0.06 percent, with the balance iron.
    Permanent magnet iron-chromium-cobalt alloy stainless strip is also 
excluded from the scope of this order. This ductile stainless steel 
strip contains, by weight, 26 to 30 percent chromium, and 7 to 10 
percent cobalt, with the remainder of iron, in widths 228.6 mm or less, 
and a thickness between 0.127 and 1.270 mm. It exhibits magnetic 
remanence between 9,000 and 12,000 gauss, and a coercivity of between 
50 and 300 oersteds. This product is most commonly used in electronic 
sensors and is currently available under proprietary trade names such 
as ``Arnokrome III.'' \2\
---------------------------------------------------------------------------

    \2\ ``Arnokrome III'' is a trademark of the Arnold Engineering 
Company.
---------------------------------------------------------------------------

    Certain electrical resistance alloy steel is also excluded from the 
scope of this order. This product is defined as a non-magnetic 
stainless steel manufactured to American Society of Testing and 
Materials (ASTM) specification B344 and containing, by weight, 36 
percent nickel, 18 percent chromium, and 46 percent iron, and is most 
notable for its resistance to high temperature corrosion. It has a 
melting point of 1390 degrees Celsius and displays a creep rupture 
limit of 4 kilograms per square millimeter at 1000 degrees Celsius. 
This steel is most commonly used in the production of heating ribbons 
for circuit breakers and industrial furnaces, and in rheostats for 
railway locomotives. The product is currently available under 
proprietary trade names such as ``Gilphy 36.'' \3\
---------------------------------------------------------------------------

    \3\ ``Gilphy 36'' is a trademark of Imphy, S.A.
---------------------------------------------------------------------------

    Certain martensitic precipitation-hardenable stainless steel is 
also excluded from the scope of this order. This high-strength, ductile 
stainless steel product is designated under the Unified Numbering 
System (UNS) as S45500-grade steel, and contains, by weight, 11 to 13 
percent chromium, and 7 to 10 percent nickel. Carbon, manganese, 
silicon and molybdenum each comprise, by weight, 0.05 percent or less, 
with phosphorus and sulfur each comprising, by weight, 0.03 percent or 
less. This steel has copper, niobium, and titanium added to achieve 
aging, and will exhibit yield strengths as high as 1700 Mpa and 
ultimate tensile strengths as high as 1750 Mpa after aging, with 
elongation percentages of 3 percent or less in 50 mm. It is generally 
provided in thicknesses between 0.635 and 0.787 mm, and in widths of 
25.4 mm. This product is most commonly used in the manufacture of 
television tubes and is currently available under proprietary trade 
names such as ``Durphynox 17.''\4\
---------------------------------------------------------------------------

    \4\ ``Durphynox 17'' is a trademark of Imphy, S.A.
---------------------------------------------------------------------------

    Finally, three specialty stainless steels typically used in certain 
industrial blades and surgical and medical instruments are also 
excluded from the scope of this order. These include stainless steel 
strip in coils used in the production of textile cutting tools (e.g., 
carpet knives).\5\ This steel is similar to AISI grade 420 but 
containing, by weight, 0.5 to 0.7 percent of molybdenum. The steel also 
contains, by weight, carbon of between 1.0 and 1.1 percent, sulfur of 
0.020 percent or less, and includes between 0.20 and 0.30 percent 
copper and between 0.20 and 0.50 percent cobalt. This steel is sold 
under proprietary names such as ``GIN4 Mo.'' The second excluded 
stainless steel strip in coils is similar to AISI 420-J2 and contains, 
by weight, carbon of between 0.62 and 0.70 percent, silicon of between 
0.20 and 0.50 percent, manganese of between 0.45 and 0.80 percent, 
phosphorus of no more than 0.025 percent and sulfur of no more than 
0.020 percent. This steel has a carbide density on average of 100 
carbide particles per 100 square microns. An example of this product is 
``GIN5'' steel. The third specialty steel has a chemical composition 
similar to AISI 420 F, with carbon of between 0.37 and 0.43 percent, 
molybdenum of between 1.15 and 1.35 percent, but lower manganese of 
between 0.20 and 0.80 percent, phosphorus of no more than 0.025 
percent, silicon of between 0.20 and 0.50 percent, and sulfur of no 
more than 0.020 percent. This product is supplied with a hardness of 
more than Hv 500 guaranteed after customer processing, and is supplied 
as, for example, ``GIN6''.\6\
---------------------------------------------------------------------------

    \5\ This list of uses is illustrative and provided for 
descriptive purposes only.
    \6\ ``GIN4 Mo,'' ``GIN5'' and ``GIN6'' are the proprietary 
grades of Hitachi Metals America, Ltd.
---------------------------------------------------------------------------

Analysis of Comments Received

    All issues raised in the case and rebuttal briefs by parties to 
these administrative reviews are addressed in the ``Issues and Decision 
Memorandum'' (``Decision Memo'') from Joseph A. Spetrini, Deputy 
Assistant Secretary, for Import Administration, Group III to Faryar 
Shirzad, Assistant Secretary for Import Administration, dated February 
4, 2002, which is hereby adopted by this notice. A list of the issues 
which parties have raised and to which we have responded, all of which 
are in the Decision Memo, is attached to this notice as an Appendix. 
Parties can find a complete discussion of all issues raised in these 
reviews and the corresponding recommendations in this public memorandum 
which is on file at the U.S. Department of Commerce, in the Central 
Records Unit, in room B-099. In addition, a complete version of the 
Decision Memo, accessible in B-099 and on the Web at http://ia.ita.doc.gov. The paper copy and electronic version of the Decision 
Memorandum are identical in content.

Sales Below Cost in the Home Market

    As discussed in more detail in the Preliminary Results, the 
Department disregarded home market below-cost sales that failed the 
cost test for Ugine in these final results of review.

Changes Since the Preliminary Results

    Based on our analysis of comments received, we have made certain 
changes in the margin calculations. We have also corrected certain 
programming and clerical errors in our preliminary results, where 
applicable. Any alleged programming or clerical errors with which we do 
not agree are discussed in the relevant sections of the Decision Memo, 
accessible in B-099 and on the Web at http://ia.ita.doc.gov.

Final Results of the Reviews

    We determine that the following percentage weighted-average margins 
exist for the period January 4, 1999 through June 30, 2000:

                Stainless Steel Sheet and Strip in Coils
------------------------------------------------------------------------
                                                              Weighted-
                                                               average
               Producer/manufacturer/exporter                   margin
                                                              (Percent)
------------------------------------------------------------------------
Ugine......................................................         3.11
------------------------------------------------------------------------


[[Page 6495]]

    The Department shall determine, and the U.S. Customs Service 
(``Customs'') shall assess, antidumping duties on all appropriate 
entries. In accordance with 19 CFR 351.212(b), we have calculated 
exporter/importer-specific assessment rates. With respect to both 
export price and constructed export price sales, we divided the total 
dumping margins for the reviewed sales by the total entered value of 
those reviewed sales for each importer. We will direct Customs to 
assess the resulting percentage margins against the entered Customs 
values for the subject merchandise on each of that importer's entries 
under the relevant order during the review period.

Cash Deposit Requirements

    The following deposit requirements will be effective upon 
publication of this notice of final results of administrative reviews 
for all shipments of stainless steel sheet and strip in coils from 
France entered, or withdrawn from warehouse, for consumption on or 
after the date of publication, as provided by section 751(a)(1) of the 
Act: (1) The cash deposit rates for the reviewed companies will be the 
rates shown above except that, for firms whose weighted-average margins 
are less than 0.5 percent and therefore de minimis, the Department 
shall require no deposit of estimated antidumping duties; (2) for 
previously reviewed or investigated companies not listed above, the 
cash deposit rate will continue to be the company-specific rate 
published for the most recent period; (3) if the exporter is not a firm 
covered in this review, a prior review, or the original less than fair 
value (``LTFV'') investigation, but the manufacturer is, the cash 
deposit rate will be the rate established for the most recent period 
for the manufacturer of the merchandise; and (4) the cash deposit rate 
for all other manufacturers or exporters will continue to be 9.38 
percent. See Notice of Amended Final Determination of Sales at Less 
Than Fair Value and Antidumping Duty Order; Stainless Steel Sheet and 
Strip in Coils from France, 64 FR 40562 (July 27, 1999).
    These deposit requirements shall remain in effect until publication 
of the final results of the next administrative review.
    This notice also serves as a final reminder to importers of their 
responsibility under 19 CFR 351.402(f) to file a certificate regarding 
the reimbursement of antidumping and countervailing duties prior to 
liquidation of the relevant entries during this review period. Failure 
to comply with this requirement could result in the Secretary's 
presumption that reimbursement of antidumping and countervailing duties 
occurred and the subsequent assessment of doubled antidumping and 
countervailing duties.
    This notice also serves as the only reminder to parties subject to 
administrative protective orders (``APO'') of their responsibility 
concerning the return or destruction of proprietary information 
disclosed under APO in accordance with 19 CFR 351.305. Timely written 
notification of the return/destruction of APO materials or conversion 
to judicial protective order is hereby requested. Failure to comply 
with the regulations and terms of an APO is a violation which is 
subject to sanction.
    We are issuing and publishing this determination and notice in 
accordance with sections 751(a)(1) and 777(i) of the Act.

    Dated: February 7, 2002.
Faryar Shirzad,
Assistant Secretary, for Import Administration.

Appendix

Issues in Decision Memo

Comments and Responses

General Comments

1. Inclusion of Affiliate U.S. sales
2. Home Market Downstream Sales
3. Negative Margin sales in calculating the antidumping duty margin
4. U. S. commission rate for certain U.S. sales by Hague Steel
5. Foreign Inland Freight
6. CEP Profit
7. Further Manufacturing sales
8. Commission offset and CEP offset
9. Home Market Surcharges
10. Inadvertent computer programming error

[FR Doc. 02-3386 Filed 2-11-02; 8:45 am]
BILLING CODE 3510-DS-P