[Federal Register Volume 66, Number 136 (Monday, July 16, 2001)]
[Rules and Regulations]
[Pages 36924-36946]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 01-17333]


-----------------------------------------------------------------------

ENVIRONMENTAL PROTECTION AGENCY

40 CFR Part 63

[AD-FRL-7010-1]
RIN 2060-AH47


National Emission Standards for Hazardous Air Pollutants: Group I 
Polymers and Resins and Group IV Polymers and Resins

AGENCY: Environmental Protection Agency (EPA).

ACTION: Final rule; technical amendments.

-----------------------------------------------------------------------

SUMMARY: The EPA is taking final action to amend certain portions of 
the national emission standards for hazardous air pollutants (NESHAP) 
for Group I Polymers and Resins; and the NESHAP for Group IV Polymers 
and Resins, which were promulgated in September 1996. These changes 
consist of minor cross referencing and typographical errors, as well as 
minor clarifications.
    These amendments will not change the basic control requirements of 
the NESHAP or the level of health protection they provide. These 
amendments do not alter the requirement for new and existing major 
sources to control emissions of hazardous air pollutants to the level 
reflecting application of the maximum achievable control technology.
    Section 553 of the Administrative Procedure Act provides that, when 
an agency for good cause finds that notice and public procedure are 
impracticable, unnecessary, or contrary to the public interest, the 
agency may issue a rule without providing notice and an opportunity for 
public comment. The EPA has determined that there is good cause for 
making these rule amendments final without prior proposal and 
opportunity for comment because these minor technical corrections are 
noncontroversial in nature, and because they do not substantively 
change the requirements of these NESHAP. Thus, notice and public 
procedure are unnecessary. The EPA finds that this constitutes good 
cause under section 553 of the Administrative Procedure Act.

EFFECTIVE DATE: July 16, 2001.

ADDRESSES: Docket number A-92-44 for the Group I Polymers and Resins 
NESHAP and Docket number A-92-45 for the Group IV Polymers and Resins 
NESHAP contain supporting information used in developing the standards. 
The dockets are located at the U.S. EPA, Room M-1500, 1200 Pennsylvania 
Avenue, Washington, DC 20460, and may be inspected from 8:30 a.m. to 
5:30 p.m., Monday through Friday, excluding legal holidays.

FOR FURTHER INFORMATION CONTACT: For information concerning these final 
rule amendments, contact Mr. Robert Rosensteel, Organic Chemicals 
Group, Emission Standards Division (MD-13), Office of Air Quality 
Planning and Standards, U.S. EPA, Research Triangle Park, North 
Carolina 27711, telephone number (919) 541-5608, facsimile number (919) 
541-3470, electronic mail address: [email protected].

SUPPLEMENTARY INFORMATION: Docket. The docket reflects the full 
administrative record for this action and includes all the information 
relied upon by EPA in the development of these NESHAP. The docket is a 
dynamic file because material is added throughout the rulemaking 
process. The docketing system is intended to allow members of the 
public and industries involved to readily identify and locate documents 
so that they can effectively participate in the rulemaking process. 
Along with the proposed and promulgated NESHAP and their preambles, the 
contents of the docket will serve as the record in the case of judicial 
review. (See section 307(d)(7)(A) of the Clean Air Act (CAA).) The 
regulatory text and other materials related to this rulemaking are 
available for review in the docket or copies may be mailed on request 
from the Air Docket by calling (202) 260-7548. A reasonable fee may be 
charged for copying docket materials.
    World Wide Web (WWW). In addition to being available in the docket, 
an electronic copy of this action will also be available on the WWW 
through the Technology Transfer Network (TTN). Following the 
Administrator's signature, a copy of the action will be posted on the 
TTN's policy and guidance page for newly proposed or promulgated rules 
http://www.epa.gov/ttn/oarpg. The TTN provides information and 
technology exchange in various areas of air pollution control. If more 
information regarding the TTN is needed, call the TTN HELP line at 
(919) 541-5384.
    Regulated Entities. The regulated category and entities affected by 
this action include:

[[Page 36925]]



----------------------------------------------------------------------------------------------------------------
                Category                  SIC codes         NAICS            Examples of regulated entities
----------------------------------------------------------------------------------------------------------------
Industry...............................   2821, 2822    325211, 325212  Butyl Rubber, Halobutyl Rubber,
                                                                         Epichlorohydrin Elastomer, Ethylene
                                                                         Propylene Rubber, Hypalon TM, Neoprene,
                                                                         Nitrile Butadiene Rubber, Nitrile
                                                                         Butadiene Latex, Polybutadiene Rubber,
                                                                         Styrene-Butadiene Rubber or Latex,
                                                                         Acrylonitrile Butadiene Styrene Resin,
                                                                         Styrene Acrylonitrile Resin, Methyl
                                                                         Methacrylate Acrylonitrile Butadiene
                                                                         Styrene Resin, Methyl Methacrylate
                                                                         Butadiene Styrene Resin, Poly(ethylene
                                                                         terephthalate) Resin, Polystyrene
                                                                         Resin, and Nitrile Resin producers.
----------------------------------------------------------------------------------------------------------------

    This table is not intended to be exhaustive, but rather provides a 
guide for readers likely to be interested in the amendments to the 
standards affected by this action. To determine whether your facility 
is regulated by this action, you should carefully examine all of the 
applicability criteria in Sec. 63.480 of the Group I Polymers and 
Resins NESHAP and Sec. 63.1310 of the Group IV Polymers and Resins 
NESHAP. If you have any questions regarding the applicability of these 
amendments to a particular entity, consult the person listed in the 
preceding FOR FURTHER INFORMATION CONTACT section.

I. Background

    On September 5, 1996 (61 FR 46906) and September 12, 1996 (61 FR 
48208), the EPA promulgated NESHAP for Group I Polymers and Resins (40 
CFR part 63, subpart U) and the NESHAP for Group IV Polymers and Resins 
(40 CFR part 63, subpart JJJ), respectively. In November 1996, 
petitions for review of the September 1996 Groups I and IV Polymers and 
Resins NESHAP were filed in the U.S. Court of Appeals for the District 
of Columbia Circuit. The petitioners raised numerous technical issues 
and concerns with these NESHAP. Based on a settlement agreement that 
was reached in 1998 between EPA and the petitioners, EPA promulgated 
amendments to these NESHAP on June 19, 2000 (65 FR 38030). After 
promulgation of those amendments, based in part on information provided 
by industry, EPA determined the rule required some minor changes both 
to carry out the purpose of the June 19, 2000 amendments and to correct 
errors in sections of the rule. These changes consist of minor 
referencing and typographical corrections, removing discrepancies 
between subparts U and JJJ, as well as minor clarifications. In this 
action, we are promulgating amendments to correct these minor errors.
    In addition to these final amendments to subparts U and JJJ, other 
actions taken to amend various aspects of subparts U and JJJ since the 
original promulgation of these NESHAP in September of 1996 include the 
following Federal Register notices: January 14, 1997 (62 FR 1835), 
equipment leaks compliance date extension for both NESHAP; June 6, 1997 
(62 FR 30993), equipment leaks compliance date extension for 
poly(ethylene terephthalate) (PET) resin affected sources; July 15, 
1997 (62 FR 37720), minor corrections and clarifications to the NESHAP; 
February 27, 1998 (63 FR 9944), change in the effective date to 
February 27, 1998 for subpart JJJ; March 31, 1998 (63 FR 15312), a 
temporary compliance extension until February 27, 2001 for existing 
affected sources producing PET using the continuous terephthalic acid 
(TPA) high viscosity multiple end finisher process; December 9, 1998 
(63 FR 67879), notification of a proposed partial settlement; March 9, 
1999 (64 FR 11536), clarifications and corrections to the NESHAP; March 
9, 1999 (64 FR 11561), proposed amendments to the NESHAP; May 7, 1999 
(64 FR 24511), withdrawal of one amendment from the amendments in the 
March 9, 1999 direct final rule as a result of adverse comments; June 
8, 1999 (64 FR 30406), equipment leaks compliance date extension for 
new and existing affected sources producing PET; June 8, 1999 (64 FR 
30456), proposed denial of petition for reconsideration of the 
equipment leak requirements in subpart JJJ; June 30, 1999 (64 FR 
35023), indefinite stay of the compliance dates for certain provisions 
under subparts U and JJJ; June 19, 2000 (65 FR 38030), promulgated 
amendments to the NESHAP; August 29, 2000 (65 FR 52319), indefinite 
stay of compliance date for existing affected sources producing PET 
using the TPA high viscosity multiple end finisher process; October 26, 
2000 (65 FR 64161), withdrawal of indefinite stay of compliance date 
for existing affected sources producing PET using the TPA high 
viscosity multiple end finisher process; February 23, 2001 (66 FR 
11233), indefinite stay of compliance date for existing affected 
sources producing PET using the TPA high viscosity multiple end 
finisher process; and February 26, 2001 (66 FR 11543), compliance date 
extension for new and existing affected sources producing PET, in order 
to complete reconsideration of the equipment leaks requirements in 
subpart JJJ.

II. Summary of Corrections

    Today's changes are described in Table 2 to this preamble for the 
convenience of the reader.

[[Page 36926]]



------------------------------------------------------------------------
          40 CFR, Part 63                           Change
------------------------------------------------------------------------
Subpart U:
  Sec.  63.480(i)(2)(ii)...........  Corrects compliance date.
  Sec.  63.482.....................  Clarifies the definitions of the
                                      terms ``Group 1 wastewater
                                      stream'' and ``Reconstruction'' by
                                      removing an internal
                                      inconsistency.
  Sec.  63.485(k)..................  Adds cross reference.
  Sec.  63.487(a)(1)(i)............  Corrects typographical error.
  Sec.  63.487(b)(2)...............  Clarifies when correction to 3
                                      percent oxygen is required for
                                      combustion control devices by
                                      making language internally
                                      consistent within the rule.
  Sec.  63.487(f)(1)(ii)...........  Corrects cross reference.
  Sec.  63.487(g)(1)(ii)...........  Corrects cross reference.
  Sec.  63.489(e)(1)(ii)...........  Clarifies the emission reduction
                                      options.
  Sec.  63.501(c)..................  Clarifies exemptions to certain
                                      wastewater requirements.
  Sec.  63.506(e)(5)(i)............  Removes the inapplicable term
                                      ``continuous monitoring system
                                      performance evaluations.''
  Sec.  63.506(e)(5)(ii)(D)........  Corrects cross reference.
  Sec.  63.506(e)(6)(iii)(A).......  Corrects cross reference.
  Sec.  63.506(e)(7)(ii)(A)........  Removes cross reference to
                                      (e)(7)(iii).
  Sec.  63.506(e)(7)(ii)(B)........  Removes cross reference to
                                      (e)(7)(ii).
  Table 1..........................  Clarifies compliance demonstration
                                      requirements for flares.
  Table 2..........................  Changes Sec.  63.183 to Sec.
                                      63.182 and notes that Sec.  63.131
                                      is a reserved section.
  Table 6..........................  Moves entry regarding ``Absorber''
                                      control/recovery device into the
                                      correct columns.
  Table 9..........................  Corrects due dates for
                                      Precompliance Report and Emissions
                                      Averaging Plan; moves text
                                      regarding the Precompliance Report
                                      in ``Description of Report'' to
                                      the correct ``Due Date'' column.
Subpart JJJ:
  Sec.  63.1310(i)(1)(i)...........  Corrects text, removes ``as
                                      provided in Sec.  63.6(b)''
                                      consistent with Table 1 entry.
  Sec.  63.1310(i)(2)(ii)..........  Removes reference to Sec.  63.1329
                                      applicable to existing process
                                      contact cooling towers.
  Sec.  63.1310(i)(2)(iii).........  Removes reference to Sec.  63.1329
                                      applicable to existing process
                                      contact cooling towers.
  Sec.  63.1311(b).................  Corrects compliance date that was
                                      inadvertently changed in a
                                      previous notice.
  Sec.  63.1312....................  Clarifies the definition of the
                                      term ``Group 1 wastewater stream''
                                      by removing an internal
                                      inconsistency.
  Sec.  63.1315(a)(9)..............  Adds cross reference.
  Sec.  63.1315(d).................  Removes ``are not subject to the
                                      provisions of this section and
                                      instead.''
  Sec.  63.1316(b)(1)(i)(B)........  Adds word ``or'' to the end of the
                                      paragraph.
  Sec.  63.1318(a).................  Clarifies performance test
                                      requirements.
  Sec.  63.1319(a).................  Corrects cross reference.
  Sec.  63.1320(a).................  Corrects cross reference.
  Sec.  63.1320(b)(3)..............  Removes incorrect citation.
  Sec.  63.1322(f)(1)(ii)..........  Corrects cross reference.
  Sec.  63.1322(g)(1)(ii)..........  Corrects cross reference.
  Sec.  63.1323(b)(6)(i)(C)........  Corrects cross reference.
  Sec.  63.1323(h)(1)..............  Adds text ``. . . after the last
                                      recover device (if any recovery
                                      devices are present) . . .'' to
                                      clarify the location for
                                      determining halogen status.
  Sec.  63.1324(f)(1)(ii)..........  Clarifies that there are two
                                      emission reduction control
                                      options.
  Sec.  63.1327(b).................  Corrects cross reference.
  Sec.  63.1330(a).................  Revises paragraph (a) to be
                                      consistent with added paragraphs
                                      (d) and (e).
  Sec.  63.1330(b)(8)(i)-(ii)......  Removes typographical error--extra
                                      word ``of'' in each paragraph.
  Sec.  63.1330(d).................  Adds paragraph inadvertently left
                                      out of the NESHAP.
  Sec.  63.1330(e).................  Adds paragraph inadvertently left
                                      out of the NESHAP.
  Sec.  63.1335(e)(5)(i)...........  Removes the inapplicable term
                                      ``continuous monitoring system
                                      performance evaluations.''
  Sec.  63.1335(e)(7)(ii)(A).......  Removes cross reference (e)(7)(ii).
  Sec.  63.1335(e)(7)(i)(B)........  Removes cross reference (e)(7)(ii).
  Table 1..........................  Clarifies compliance demonstration
                                      requirements for flares.
  Table 6..........................  Adds check marks for acrylonitrile
                                      and 1,3-butadiene to MABS row.
  Table 6..........................  Adds check marks for
                                      methylmethacrylate to MABS and MBS
                                      rows.
  Table 7..........................  Corrects superscript error for
                                      Precompliance Report in the fourth
                                      record/report for scrubber for
                                      halogenated batch vents.
  Table 9..........................  Corrects due date for Precompliance
                                      Report; moves text regarding the
                                      Precompliance Report in
                                      ``Description of Report'' to the
                                      correct ``Due Date'' column;
                                      corrects Emissions Averaging Plan
                                      due date.
------------------------------------------------------------------------


[[Page 36927]]

III. Administrative Requirements

    Under Executive Order 12866 (58 FR 51735, October 4, 1993), this 
action is not a ``significant regulatory action'' and is therefore not 
subject to review by the Office of Management and Budget. Because the 
Agency has made a ``good cause'' finding that this action is not 
subject to notice-and-comment requirements under the Administrative 
Procedure Act or any other statute (see summary), it is not subject to 
the regulatory flexibility provisions of the Regulatory Flexibility Act 
(5 U.S.C. 601 et seq.), or to sections 202 and 205 of the Unfunded 
Mandates Reform Act of 1995 (UMRA) (Public Law 104-4). In addition, 
this action does not significantly or uniquely affect small governments 
or impose a significant intergovernmental mandate, as described in 
sections 203 and 204 of UMRA. These rule amendments also do not 
significantly or uniquely affect the communities of tribal governments, 
as specified by Executive Order 13175 (65 FR 67249, November 6, 2000). 
These rule amendments will not have substantial direct effects on the 
States, on the relationship between the national government and the 
States, or on the distribution of power and responsibilities among the 
various levels of government, as specified in Executive Order 13132 (64 
FR 43255, August 10, 1999). These rule amendments also are not subject 
to Executive Order 13045 (62 FR 19885, April 23, 1997), because they 
are not economically significant.
    This technical correction action does not involve technical 
standards; thus, the requirements of section 12(d) of the National 
Technology Transfer and Advancement Act of 1995 (15 U.S.C. 272 note) do 
not apply. These rule amendments also do not involve special 
consideration of environmental justice related issues as required by 
Executive Order 12898 (59 FR 7629, February 16, 1994). In issuing these 
amendments, EPA has taken the necessary steps to eliminate drafting 
errors and ambiguity, minimize potential litigation, and provide a 
clear legal standard for affected conduct, as required by section 3 of 
Executive Order 12988 (61 FR 4729, February 7, 1996). The EPA has 
complied with Executive Order 12630 (53 FR 8859, March 15, 1988) by 
examining the takings implications of these rule amendments in 
accordance with the ``Attorney General's Supplemental Guidelines for 
the Evaluation of Risk and Avoidance of Unanticipated Takings'' issued 
under the Executive Order. These rule amendments do not impose an 
information collection burden under the provisions of the Paperwork 
Reduction Act of 1995 (44 U.S.C. 3501 et seq.). The EPA's compliance 
with these statutes and Executive Orders for the underlying rules is 
discussed in the September 5, 1996 (61 FR 46906) and the September 12, 
1996 (61 FR 48208) Federal Register notices.
    The Congressional Review Act (5 U.S.C. 801 et seq.), as added by 
the Small Business Regulatory Enforcement Fairness Act of 1996, 
generally provides that before a rule may take effect, the agency 
promulgating the rule must submit a rule report, which includes a copy 
of the rule, to each House of the Congress and to the Comptroller 
General of the United States. Section 808 allows the issuing agency to 
make a rule effective sooner than otherwise provided by the 
Congressional Review Act if the agency makes a good cause finding that 
notice and public procedure is impracticable, unnecessary or contrary 
to the public interest. This determination must be supported by a brief 
statement (5 U.S.C. 808(2)). As stated previously, EPA has made such a 
good cause finding, including the reasons therefor, and established an 
effective date of July 16, 2001. The EPA will submit a report 
containing this rule and other required information to the U.S. Senate, 
the U.S. House of Representatives, and the Comptroller General of the 
United States prior to publication of the rule in the Federal Register. 
This action is not a ``major rule'' as defined by 5 U.S.C. 804(2).

List of Subjects in 40 CFR Part 63

    Environmental protection, Administrative practice and procedure, 
Air pollution control, Hazardous substances, Intergovernmental 
relations, Reporting and recordkeeping requirements.

    Dated: July 3, 2001.
Christine Todd Whitman,
Administrator.

    For the reasons set out in the preamble, part 63 of title 40, 
chapter I of the Code of Federal Regulations is amended as follows:

PART 63--NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS 
FOR SOURCE CATEGORIES

    1. The authority citation for part 63 continues to read as follows:

    Authority: 42 U.S.C. 7401, et seq.

Subpart U--National Emission Standards for Hazardous Air Pollutant 
Emissions: Group I Polymers and Resins

    2. Section 63.480 is amended by revising paragraph (i)(2)(ii) to 
read as follows:


Sec. 63.480  Applicability and designation of affected sources.

* * * * *
    (i) * * *
    (2) * * *
    (ii) If any components are replaced at an existing affected source 
such that the criteria specified in paragraphs (i)(2)(i)(A) and 
(i)(2)(i)(B) of this section are not met and that replacement of 
components creates one or more emission points (i.e., either newly 
created Group 1 emission points or emission points that change from 
Group 2 to Group 1) or causes any other emission point to be added 
(i.e., Group 2 emission points, back-end process operations subject to 
Secs. 63.493 and 63.500, and heat exchange systems and equipment leak 
components subject to Sec. 63.502), the resulting emission point(s) 
shall be subject to the applicable requirements for an existing 
affected source. The resulting emission point(s) shall be in compliance 
by 120 days after the date of initial start-up or by the appropriate 
compliance date specified in Sec. 63.481 (i.e., July 31, 1997 for most 
equipment leak components subject to Sec. 63.502, and June 19, 2001 for 
emission points other than equipment leaks), whichever is later.
* * * * *

    3. Section 63.482(b) is amended by revising the definitions ``Group 
1 wastewater stream'' and ``Reconstruction.''


Sec. 63.482  Definitions.

* * * * *
    (b) * * *
    Group 1 wastewater stream means a wastewater stream consisting of 
process wastewater from an existing or new affected source that meets 
the criteria for Group 1 status in Sec. 63.132(c), with the exceptions 
listed in Sec. 63.501(a)(10) for the purposes of this subpart (i.e., 
for organic HAP as defined in this section).
* * * * *
    Reconstruction means the replacement of components of an affected 
source or of a previously unaffected stationary source that becomes an 
affected source as a result of the replacement, to such an extent that:
    (1) The fixed capital cost of the new components exceeds 50 percent 
of the fixed capital cost that would be required

[[Page 36928]]

to construct a comparable new source; and
    (2) It is technologically and economically feasible for the 
reconstructed source to meet the provisions of this subpart.
* * * * *

    4. Section 63.485 is amended by revising the first sentence of 
paragraph (k) to read as follows:


Sec. 63.485  Continuous front-end process vent provisions.

* * * * *
    (k) When Sec. 63.114(e) or Sec. 63.117(f) specifies that an owner 
or operator shall submit the information required in Sec. 63.152(b) in 
order to establish the parameter monitoring range, the owner or 
operator of an affected source shall comply with the provisions of 
Sec. 63.505 for establishing the parameter monitoring level and shall 
comply with Sec. 63.506(e)(5) for the purposes of reporting information 
related to the establishment of the parameter monitoring level, for the 
purposes of this subpart. * * *
* * * * *

    5. Section 63.487 is amended as follows:
    a. By revising paragraph (a)(1)(i);
    b. By revising paragraph (b)(2);
    c. In paragraph (f)(1)(ii), by revising the reference to 
``Sec. 63.506(e)(5)(iv)'' to read ``Sec. 63.506(e)(5)(ix)''.
    d. In paragraph (g)(1)(ii), by revising the reference to 
``Sec. 63.506(e)(5)(iv)'' to read ``Sec. 63.506(e)(5)(ix)''.
    The revisions to paragraphs (a)(1)(i) and (b)(2) read as follows:


Sec. 63.487  Batch front-end process vents--reference control 
technology.

    (a) * * *
    (1) * * *
    (i) The owner or operator of the affected sources shall comply with 
the requirements of Sec. 63.504(c) for the flare.
* * * * *
    (b) * * *
    (2) For each aggregate batch vent stream, reduce organic HAP 
emissions by 90 weight percent or to a concentration of 20 ppmv, 
whichever is less stringent, on a continuous basis using a control 
device. For purposes of complying with the 20 ppmv outlet concentration 
standard, the outlet concentration shall be calculated on a dry basis. 
When a combustion device is used for purposes of complying with the 20 
ppmv outlet concentration standard, the concentration shall be 
corrected to 3 percent oxygen if supplemental combustion air is used to 
combust the emissions. If supplemental combustion air is not used, a 
correction to 3 percent oxygen is not required.
* * * * *

    6. Section 63.489 is amended by revising paragraph (e)(1)(ii) to 
read as follows:


Sec. 63.489  Batch front-end process vents--monitoring equipment.

* * * * *
    (e) * * *
    (1) * * *
    (ii) For aggregate batch vent streams using a control device to 
comply with Sec. 63.487(b)(2), the established level shall reflect the 
emission reduction requirement of either 90 percent or 20 ppmv 
specified in Sec. 63.487(b)(2).
* * * * *

    7. Section 63.501 is amended by revising paragraph (c) to read as 
follows:


Sec. 63.501  Wastewater provisions.

* * * * *
    (c) The provisions of paragraphs (a) and (b) of this section do not 
apply to the following:
    (1) Back-end streams originating from equipment whose only 
elastomer products are latex products.
    (2) Back-end streams at affected sources that are subject to a 
residual organic HAP limitation in Sec. 63.494(a), and that are 
complying with these limitations through the use of stripping 
technology.
* * * * *

    8. Section 63.506 is amended as follows:
    a. By revising paragraph (e)(5)(i) introductory text;
    b. In paragraph (e)(5)(ii)(D), by revising the reference to 
``Sec. 63.505 (b)(3)(ii)'' to read ``Sec. 63.505 (b)(3)(iii)';
    c. In paragraph (e)(6)(iii)(A), by revising the references to 
``Sec. 63.146(f)'' to read ``Sec. 63.146(g)'' and ``Sec. 63.104(b)(4)'' 
to read ``Sec. 63.104(f)(2); and
    d. By revising paragraph (e)(7)(ii)(A); and
    e. By revising paragraph (e)(7)(ii)(B).
    The revisions read as follows:


Sec. 63.506  General recordkeeping and reporting provisions.

* * * * *
    (e) * * *
    (5) * * *
    (i) The results of any emission point group determinations, process 
section applicability determinations, performance tests, inspections, 
any other information used to demonstrate compliance, values of 
monitored parameters established during performance tests, and any 
other information required to be included in the Notification of 
Compliance Status under Secs. 63.122 and 63.484 for storage vessels, 
Sec. 63.117 for continuous front-end process vents, Sec. 63.492 for 
batch front-end process vents, Sec. 63.499 for back-end process 
operations, Sec. 63.146 for process wastewater, and Sec. 63.503 for 
emission points included in an emissions average. In addition, the 
owner or operator of an affected source shall comply with paragraphs 
(e)(5)(i)(A) and (e)(5)(i)(B) of this section.
* * * * *
    (7) * * *
    (i) * * *
    (ii) * * *
    (A) If use of a nominal control efficiency is part of the initial 
Emissions Averaging Plan described in paragraph (e)(4)(ii) of this 
section, the information shall be submitted with the Emissions 
Averaging Plan.
    (B) If an owner or operator elects to use a nominal control 
efficiency after submittal of the initial Emissions Averaging Plan as 
described in paragraph (e)(4)(ii) of this section, the information 
shall be submitted at the discretion of the owner or operator.
* * * * *

    9. Revise Tables 1, 2, 5, 6, and 9 to subpart U of part 63, to read 
as follows:

[[Page 36929]]



                                         Table 1 to Subpart U of Part 63
                       [Applicability of general provisions to subpart U affected sources]
----------------------------------------------------------------------------------------------------------------
               Reference                  Applies to subpart U                     Explanation
----------------------------------------------------------------------------------------------------------------
Sec.  63.1(a)(1)......................  Yes....................  Sec.  63.482 specifies definitions in addition
                                                                  to or that supersede definitions in Sec.
                                                                  63.2.
Sec.  63.1(a)(2)......................  Yes.
Sec.  63.1(a)(3)......................  Yes....................  Sec.  63.481(f) through (k) and Sec.  63.160(b)
                                                                  identify those standards which may apply in
                                                                  addition to the requirements of subparts U and
                                                                  H of this part, and specify how compliance
                                                                  shall be achieved.
Sec.  63.1(a)(4)......................  Yes....................  Subpart U (this table) specifies the
                                                                  applicability of each paragraph in subpart A
                                                                  to subpart U.
Sec.  63.1(a)(5)......................  No.....................  [Reserved.].
Sec.  63.1(a)(6)-(8)..................  Yes.
Sec.  63.1(a)(9)......................  No.....................  [Reserved.].
Sec.  63.1(a)(10).....................  Yes.
Sec.  63.1(a)(11).....................  Yes.
Sec.  63.1(a)(12)-(14)................  Yes.
Sec.  63.1(b)(1)......................  No.....................  Sec.  63.480(a) contains specific applicability
                                                                  criteria.
Sec.  63.1(b)(2)......................  Yes.
Sec.  63.1(b)(3)......................  No.....................  Sec.  63.480(b) provides documentation
                                                                  requirements for EPPUs not considered affected
                                                                  sources.
Sec.  63.1(c)(1)......................  Yes....................  Subpart U (this table) specifies the
                                                                  applicability of each paragraph in subpart A
                                                                  to subpart U.
Sec.  63.1(c)(2)......................  No.....................  Area sources are not subject to subpart U.
Sec.  63.1(c)(3)......................  No.....................  [Reserved.].
Sec.  63.1(c)(4)......................  Yes.
Sec.  63.1(c)(5)......................  Yes....................  Except that affected sources are not required
                                                                  to submit notifications that are not required
                                                                  by subpart U.
Sec.  63.1(d).........................  No.....................  [Reserved.].
Sec.  63.1(e).........................  Yes.
Sec.  63.2............................  Yes....................  Sec.  63.482 specifies those subpart A
                                                                  definitions that apply to subpart U.
Sec.  63.3............................  Yes.
Sec.  63.4(a)(1)-(3)..................  Yes.
Sec.  63.4(a)(4)......................  No.....................  [Reserved.].
Sec.  63.4(a)(5)......................  Yes.
Sec.  63.4(b).........................  Yes.
Sec.  63.4(c).........................  Yes.
Sec.  63.5(a)(1)......................  Yes....................  Except the terms ``source'' and ``stationary
                                                                  source'' should be interpreted as having the
                                                                  same meaning as ``affected source''.
Sec.  63.5(a)(2)......................  Yes.
Sec.  63.5(b)(1)......................  Yes....................  Except Sec.  63.480(i) defines when
                                                                  construction or reconstruction is subject to
                                                                  new source standards.
Sec.  63.5(b)(2)......................  No.....................  [Reserved.].
Sec.  63.5(b)(3)......................  Yes.
Sec.  63.5(b)(4)......................  Yes....................  Except that the Initial Notification and Sec.
                                                                  63.9(b) requirements do not apply.
Sec.  63.5(b)(5)......................  Yes.
Sec.  63.5(b)(6)......................  Yes....................  Except that Sec.  63.480(i) defines when
                                                                  construction or reconstruction is subject to
                                                                  the new source standards.
Sec.  63.5(c).........................  No.....................  [Reserved.].
Sec.  63.5(d)(1)(i)...................  Yes....................  Except that the references to the Initial
                                                                  Notification and Sec.  63.9(b)(5) do not
                                                                  apply.
Sec.  63.5(d)(1)(ii)..................  Yes....................  Except that Sec.  63.5(d)(1)(ii)(H) does not
                                                                  apply.
Sec.  63.5(d)(1)(iii).................  No.....................  Sec.  63.506(e)(5) and Sec.  63.502(f) specify
                                                                  Notification of Compliance Status
                                                                  requirements.
Sec.  63.5(d)(2)......................  No.
Sec.  63.5(d)(3)......................  Yes....................  Except Sec.  63.5(d)(3)(ii) does not apply, and
                                                                  equipment leaks subject to Sec.  63.502 are
                                                                  exempt.
Sec.  63.5(d)(4)......................  Yes.
Sec.  63.5(e).........................  Yes.
Sec.  63.5(f)(1)......................  Yes.
Sec.  63.5(f)(2)......................  Yes....................  Except that where Sec.  63.9(b)(2) is referred
                                                                  to, the owner or operator need not comply.
Sec.  63.6(a).........................  Yes.
Sec.  63.6(b)(1)......................  No.....................  The dates specified in Sec.  63.481(b) apply,
                                                                  instead.
Sec.  63.6(b)(2)......................  No.
Sec.  63.6(b)(3)......................  No.
Sec.  63.6(b)(4)......................  No.
Sec.  63.6(b)(5)......................  No.
Sec.  63.6(b)(6)......................  No.....................  [Reserved.].
Sec.  63.6(b)(7)......................  No.
Sec.  63.6(c)(1)......................  Yes....................  Sec.  63.481 specifies the compliance date.
Sec.  63.6(c)(2)......................  No.

[[Page 36930]]

 
Sec.  63.6(c)(3)......................  No.....................  [Reserved.].
Sec.  63.6(c)(4)......................  No.....................  [Reserved.].
Sec.  63.6(c)(5)......................  Yes.
Sec.  63.6(d).........................  No.....................  [Reserved.].
Sec.  63.6(e).........................  Yes....................  Except as otherwise specified for
                                                                  individualparagraphs. Does not apply to Group
                                                                  2 emission points, unless they are included in
                                                                  an emissions average.a
Sec.  63.6(e)(1)(i)...................  No.....................  This is addressed by Sec.  63.480(j)(4).
Sec.  63.6(e)(1)(ii)..................  Yes.
Sec.  63.6(e)(1)(iii).................  Yes.
Sec.  63.6(e)(2)......................  Yes.
Sec.  63.6(e)(3)(i)...................  Yes....................  For equipment leaks (subject to Sec.  63.502),
                                                                  the start-up, shutdown, and malfunction
                                                                  planrequirement of Sec.  63.6(e)(3)(i) is
                                                                  limited to control devices and is optional for
                                                                  other equipment. The start-up, shutdown, and
                                                                  malfunction plan may include written
                                                                  procedures that identify conditions that
                                                                  justify a delay of repair.
Sec.  63.6(e)(3)(i)(A)................  No.....................  This is addressed by Sec.  63.480(j)(4).
Sec.  63.6(e)(3)(i)(B)................  Yes.
Sec.  63.6(e)(3)(i)(C)................  Yes.
Sec.  63.6(e)(3)(ii)..................  Yes.
Sec.  63.6(e)(3)(iii).................  No.....................  Recordkeeping and reporting are specified in
                                                                  Sec.  63.506(b)(1).
Sec.  63.6(e)(3)(iv)..................  No.....................  Recordkeeping and reporting are specified in
                                                                  Sec.  63.506(b)(1).
Sec.  63.6(e)(3)(v)...................  Yes.
Sec.  63.6(e)(3)(vi)..................  Yes.
Sec.  63.6(e)(3)(vii).................  Yes.
Sec.  63.6(e)(3)(vii) (A).............  Yes.
Sec.  63.6(e)(3)(vii) (B).............  Yes....................  Except the plan shall provide for operation in
                                                                  compliance with Sec.  63.480(j)(4).
Sec.  63.6(e)(3)(vii) (C).............  Yes.
Sec.  63.6(e)(3)(viii)................  Yes.
Sec.  63.6(f)(1)......................  Yes.
Sec.  63.6(f)(2)......................  Yes....................  Except 63.7(c), as referred to in Sec.
                                                                  63.6(f)(2)(iii)(D) does not apply, and except
                                                                  that Sec.  63.6(f)(2)(ii) does not apply to
                                                                  equipment leaks subject to Sec.  63.502.
Sec.  63.6(f)(3)......................  Yes.
Sec.  63.6(g).........................  Yes.
Sec.  63.6(h).........................  No.....................  Subpart U does not require opacity and
                                                                  visibleemission standards.
Sec.  63.6(i)(1)......................  Yes.
Sec.  63.6(i)(2)......................  Yes.
Sec.  63.6(i)(3)......................  Yes.
Sec.  63.6(i)(4)(i)(A)................  Yes.
Sec.  63.6(i)(4)(i)(B)................  No.....................  Dates are specified in Sec.  63.481(e) and Sec.
                                                                   63.506(e)(3)(i).
Sec.  63.6(i)(4)(ii)..................  No.
Sec.  63.6(i)(5)-(14).................  Yes.
Sec.  63.6(i)(15).....................  No.....................  [Reserved.].
Sec.  63.6(i)(16).....................  Yes.
Sec.  63.6(j).........................  Yes.
Sec.  63.7(a)(1)......................  Yes.
Sec.  63.7(a)(2)......................  No.                      Sec.  63.506(e)(5) specifies the submittal
                                                                  dates of performance test results for all
                                                                  emission pointsexcept equipment leaks; for
                                                                  equipment leaks, compliance demonstration
                                                                  results are reported in the Periodic Reports.
Sec.  63.7(a)(3)......................  Yes.
Sec.  63.7(b).........................  No.....................  Sec.  63.504(a)(4) specifies notification
                                                                  requirements.
Sec.  63.7(c).........................  No.....................  Except if the owner or operator chooses to
                                                                  submit an alternative nonopacity emission
                                                                  standard for approval under Sec.  63.6(g).
Sec.  63.7(d).........................  Yes.
Sec.  63.7(e)(1)......................  Yes....................  Except that all performance tests shall
                                                                  beconducted at maximum representative
                                                                  operating conditions achievable at the time
                                                                  without disruption of operations or damage to
                                                                  equipment.
Sec.  63.7(e)(2)......................  Yes.
Sec.  63.7(e)(3)......................  No.....................  Subpart U specifies requirements.
Sec.  63.7(e)(4)......................  Yes.
Sec.  63.7(f).........................  Yes....................  Except that Sec.  63.144(b)(5)(iii)(A) & (B)
                                                                  shall apply for process wastewater. Also,
                                                                  since a site specific test plan is not
                                                                  required, the notification deadline in Sec.
                                                                  63.7(f)(2)(i) shall be 60 days prior to the
                                                                  performance test, and in Sec.  63.7(f)(3)
                                                                  approval or disapproval of the alternative
                                                                  test method shall not be tied to the site
                                                                  specific test plan.

[[Page 36931]]

 
Sec.  63.7(g).........................  Yes....................  Except that the requirements in Sec.
                                                                  63.506(e)(5) shall apply instead of references
                                                                  to the Notification of Compliance Status
                                                                  report in 63.9(h). In addition, equipment
                                                                  leaks subject to Sec.  63.502 are not required
                                                                  to conduct performance tests.
Sec.  63.7(h).........................  Yes....................  Except Sec.  63.7(h)(4)(ii) is not applicable,
                                                                  since the site-specific test plans in Sec.
                                                                  63.7(c)(2) arenot required.
Sec.  63.8(a)(1)......................  Yes.
Sec.  63.8(a)(2)......................  No.
Sec.  63.8(a)(3)......................  No.....................  [Reserved.].
Sec.  63.8(a)(4)......................  Yes.
Sec.  63.8(b)(1)......................  Yes.
Sec.  63.8(b)(2)......................  No.....................  Subpart U specifies locations to
                                                                  conductmonitoring.
Sec.  63.8(b)(3)......................  Yes.
Sec.  63.8(c)(1)......................  Yes.
Sec.  63.8(c)(1)(i)...................  Yes.
Sec.  63.8(c)(1)(ii)..................  No.....................  For all emission points except equipment leaks,
                                                                  comply with Sec.  63.506(b)(1)(i)(B); for
                                                                  equipmentleaks, comply with Sec.
                                                                  63.181(g)(2)(iii).
Sec.  63.8(c)(1)(iii).................  Yes.
Sec.  63.8(c)(2)......................  Yes.
Sec.  63.8(c)(3)......................  Yes.
Sec.  63.8(c)(4)......................  No.....................  Sec.  63.505 specifies monitoring frequency;
                                                                  not applicable to equipment leaks, because
                                                                  Sec.  63.502does not require continuous
                                                                  monitoring systems.
Sec.  63.8(c)(5)-(8)..................  No.
Sec.  63.8(d).........................  No.
Sec.  63.8(e).........................  No.
Sec.  63.8(f)(1)-(3)..................  Yes.
Sec.  63.8(f)(4)(i)...................  No.....................  Timeframe for submitting request is specified
                                                                  in Sec.  63.506(f) or (g); not applicable to
                                                                  equipmentleaks, because Sec.  63.502 (through
                                                                  reference to subpart H) specifies acceptable
                                                                  alternative methods.
Sec.  63.8(f)(4)(ii)..................  No.....................  Contents of request are specified in Sec.
                                                                  63.506(f) or (g).
Sec.  63.8(f)(4)(iii).................  No.
Sec.  63.8(f)(5)(i)...................  Yes.
Sec.  63.8(f)(5)(ii)..................  No.
Sec.  63.8(f)(5)(iii).................  Yes.
Sec.  63.8(f)(6)......................  No.....................  Subpart U does not require CEM's.
Sec.  63.8(g).........................  No.....................  Data reduction procedures specified inSec.
                                                                  63.506(d) and (h); not applicable to equipment
                                                                  leaks.
Sec.  63.9(a).........................  Yes.
Sec.  63.9(b).........................  No.....................  Subpart U does not require an initial
                                                                  notification.
Sec.  63.9(c).........................  Yes.
Sec.  63.9(d).........................  Yes.
Sec.  63.9(e).........................  No.....................  Sec.  63.504(a)(4) specifies notification
                                                                  deadline.
Sec.  63.9(f).........................  No.....................  Subpart U does not require opacity and visible
                                                                  emission standards.
Sec.  63.9(g).........................  No.
Sec.  63.9(h).........................  No.....................  Sec.  63.506(e)(5) specifies Notification of
                                                                  Compliance Status requirements.
Sec.  63.9(i).........................  Yes.
Sec.  63.9(j).........................  No.
Sec.  63.10(a)........................  Yes....................
Sec.  63.10(b)(1).....................  No.....................  Sec.  63.506(a) specifies record retention
                                                                  requirements.
Sec.  63.10(b)(2).....................  No.....................  Subpart U specifies recordkeeping requirements.
Sec.  63.10(b)(3).....................  No.....................  Sec.  63.480(b) requires documentation of
                                                                  sources that are not affected sources.
Sec.  63.10(c)........................  No.....................  Sec.  63.506 specifies recordkeeping
                                                                  requirements.
Sec.  63.10(d)(1).....................  Yes....................
Sec.  63.10(d)(2).....................  No.....................  Sec.  63.506(e)(5) specifies performance test
                                                                  reporting requirements; not applicable to
                                                                  equipment leaks.
Sec.  63.10(d)(3).....................  No.....................  Subpart U does not require opacity and visible
                                                                  emission standards.
Sec.  63.10(d)(4).....................  Yes....................
Sec.  63.10(d)(5)(i)..................  Yes....................  Except that reports required by Sec.
                                                                  63.10(d)(5)(i) shall be submitted at the same
                                                                  time as Periodic Reports specified in Sec.
                                                                  63.506(e)(6). The start-up, shutdown, and
                                                                  malfunction plan, and any records or reports
                                                                  of start-up, shutdown, and malfunction do not
                                                                  apply to Group 2 emission points unless they
                                                                  are included in an emissions average.
Sec.  63.10(d)(5)(ii).................  No.....................
Sec.  63.10(e)........................  No.....................  Sec.  63.506 specifies reporting requirements.
Sec.  63.10(f)........................  Yes....................

[[Page 36932]]

 
Sec.  63.11...........................  Yes....................  Sec.  63.11(b) specifies requirements for
                                                                  flares used to comply with provisions of this
                                                                  subpart. Sec.  63.504(c) contains the
                                                                  requirements to conduct compliance
                                                                  demonstrations for flares subject to this
                                                                  subpart.
Sec.  63.12...........................  Yes....................  Except that the authority of Sec.  63.503(i)
                                                                  and the authority of Sec.  63.177 (for
                                                                  equipment leaks) will not be delegated to
                                                                  States.
Secs.  63.13-63.15....................  Yes....................
----------------------------------------------------------------------------------------------------------------
a The plan and any records or reports of start-up, shutdown, and malfunction do not apply to Group 2 emission
  points unless they are included in an emissions average.


                                         Table 2 to Subpart U of Part 63
                [Applicability of Subparts F, G, & H of this Part to Subpart U affected sources]
----------------------------------------------------------------------------------------------------------------
            Reference             Applies to Subpart U          Comment          Applicable section of Subpart U
----------------------------------------------------------------------------------------------------------------
Subpart F:
  Sec.  63.100..................  No..................
  Sec.  63.101..................  Yes.................  Several definitions      Sec.  63.482.
                                                         from Sec.  63.101 are
                                                         referenced in Sec.
                                                         63.482.
  Secs.  63.102-63.103..........  No..................
  Secs.  63.104-63.105..........  Yes.................  .......................  Secs.  63.501 and 63.502.
  Secs.  63.106-63.109..........  No..................
Subpart G:
  Sec.  63.110..................  No..................
  Sec.  63.111..................  Yes.................  Several definitions      Sec.  63.482.
                                                         from Sec.  63.111
                                                         reference in Sec.
                                                         63.482.
  Sec.  63.112..................  No..................
  Secs.  63.113-63.118..........  Yes.................  With the differences
                                                         noted in Sec.  63.485
                                                         (b) through Sec.
                                                         63.485(k).
  Secs.  63.119-63.123..........  Yes.................  With the differences     63.484.
                                                         noted in Sec.
                                                         63.484(c) through
                                                         63.484(s).
  Secs.  63.124-63.125..........  No..................  [Reserved.]............
  Secs.  63.126-63.130..........  No..................
  Sec.  63.131..................    ..................  [Reserved.]............
  Secs.  63.133-63.147..........  Yes.................  With the differences     Sec.  63.501.
                                                         noted in Sec.
                                                         63.501(a)(1) through
                                                         (19).
  Secs.  63.148-63.149..........  Yes.................  With the differences     Secs.  63.484 and 63.501.
                                                         noted in Secs.
                                                         63.484(c) through (s)
                                                         and 63.501(a)(1)
                                                         through (23).
  Sec.  63.150(a) through (f)...  No..................
  Sec.  63.150(g)(1) and (2)....  No..................
  Sec.  63.150(g)(3)............  Yes.................  .......................  Sec.  63.503(g)(3).
  Sec.  63.150(g)(4)............  No..................
  Sec.  63.150(g)(5)............  Yes.................  .......................  Sec.  63.503(g)(5).
  Sec.  63.150(h)(1) and (2)....  No..................
  Sec.  63.150(h)(3)............  Yes.................  .......................  Sec.  63.503(h)(3).
  Sec.  63.150(h)(4)............  No..................
  Sec.  63.150(h)(5)............  Yes.................  .......................  Sec.  63.503(h)(5).
  Sec.  63.150(i) through (o)...  No..................
  Secs.  63.151-63.152..........  No..................
Subpart H:
  Secs.  63.160-63.182..........  Yes.................  Subpart U affected       Sec.  63.502.
                                                         sources shall comply
                                                         with all requirements
                                                         of subpart H of this
                                                         part, with the
                                                         differences noted in
                                                         Sec.  63.502.
----------------------------------------------------------------------------------------------------------------

* * * * *

                                                             Table 5 to Subpart U of Part 63
                                          [Known organic HAP emitted from the production of elastomer products]
--------------------------------------------------------------------------------------------------------------------------------------------------------
                                                                                                Elastomer product/subcategory
                                                                   -------------------------------------------------------------------------------------
                Organic HAP/chemical name (CAS No.)                                                                          PBR/
                                                                      BR    EPI    EPR    HBR    HYP    NEO    NBL    NBR    SBRS    PSR    SBL    SBRE
--------------------------------------------------------------------------------------------------------------------------------------------------------
Acrylonitrile (107131)............................................                                                         k       >

[[Page 36933]]

 
Carbon Disulfide..................................................                                                         k       >
Carbon Tetrachloride (56235)......................................                              
Methanol (67561)..................................................  
Methyl Chloride (74873)...........................................               k       >
Toluene (108883)..................................................         
Xylenes (1330207).................................................  TM.
NEO = Neoprene.
NBL = Nitrile Butadiene Latex.
NBR = Nitrile Butadiene Rubber.
PBR/SBRS = Polybutadiene and Styrene Butadiene Rubber by Solution.
PSR = Polysulfide Rubber.
SBL = Styrene Butadiene Latex.
SBRE = Styrene Butadiene Rubber by Emulsion.


                     Table 6 to Subpart U of Part 63
[Group 1 batch front-end process vents and aggregate batch vent streams--
         monitoring, recordkeeping, and reporting requirements]
------------------------------------------------------------------------
                                                      Recordkeeping and
                                 Parameter to be          reporting
   Control/recovery device          monitored         requirements for
                                                    monitored parameters
------------------------------------------------------------------------
Thermal incinerator.........  Firebox temperature   1. Continuous
                               a.                    records as
                                                     specified in Sec.
                                                     63.491(e)(1).b
                                                    2. Record and report
                                                     the average firebox
                                                     temperature
                                                     measured during the
                                                     performance test--
                                                     NCS.c
                                                    3. Record the batch
                                                     cycle daily average
                                                     firebox temperature
                                                     as specified in
                                                     Sec.  63.491(e)(2).
                                                    4. Report all batch
                                                     cycle daily average
                                                     temperatures that
                                                     are below the
                                                     minimum operating
                                                     value established
                                                     in the NCS or
                                                     operating permit
                                                     and all instances
                                                     when monitoring
                                                     data are not
                                                     collected--PR.d e
Catalytic incinerator.......  Temperature upstream  1. Continuous
                               and downstream of     records as
                               the catalyst bed.     specified in Sec.
                                                     63.491(e)(1).b
                                                    2. Record and report
                                                     the average
                                                     upstream and
                                                     downstream
                                                     temperatures and
                                                     the average
                                                     temperature
                                                     difference across
                                                     the catalyst bed
                                                     measured during the
                                                     performance test--
                                                     NCS.c
                                                    3. Record the batch
                                                     cycle daily average
                                                     upstream
                                                     temperature and
                                                     temperature
                                                     difference across
                                                     catalyst bed as
                                                     specified in Sec.
                                                     63.491(e)(2).
                                                    4. Report all batch
                                                     cycle daily average
                                                     upstream
                                                     temperatures that
                                                     are below the
                                                     minimum upstream
                                                     value established
                                                     in the NCS or
                                                     operating permit--
                                                     PR.d e

[[Page 36934]]

 
 
                                                    5. Reporting all
                                                     batch cycle daily
                                                     average temperature
                                                     differences across
                                                     the catalyst bed
                                                     that are below the
                                                     minimum difference
                                                     established in the
                                                     NCS or operating
                                                     permit--PR.d e
                                                    6. Report all
                                                     instances when
                                                     monitoring data are
                                                     not collected.
Boiler or process heater      Firebox temperature   1. Continuous
 with a design heat input      a.                    records as
 capacity less than 44                               specified in Sec.
 megawatts and where the                             63.491(e)(1).b
 batch front--end process
 vents or aggregate batch
 vent streams are ``not''
 introduced with or used as
 the primary fuel.
                                                    2. Record and report
                                                     the average firebox
                                                     temperature
                                                     measured during the
                                                     performance test--
                                                     NCS.c
                                                    3. Record the batch
                                                     cycle daily average
                                                     firebox temperature
                                                     as specified in
                                                     Sec.  63.491(e)(2).
                                                     d
                                                    4. Report all batch
                                                     cycle daily average
                                                     temperatures that
                                                     are below the
                                                     minimum operating
                                                     value established
                                                     in the NCS or
                                                     operating permit
                                                     and all instances
                                                     when monitoring
                                                     data are not
                                                     collected--PR.d e
Flare.......................  Presence of a flame   1. Hourly records of
                               at the pilot light.   whether the monitor
                                                     was continuously
                                                     operating during
                                                     light batch
                                                     emission episodes
                                                     selected for
                                                     control and whether
                                                     a flame was
                                                     continuously
                                                     present at the
                                                     pilot light during
                                                     each hour.
                                                    2. Record and report
                                                     the presence of a
                                                     flame at the pilot
                                                     light over the full
                                                     period of the
                                                     compliance
                                                     determination--NCS.
                                                     c
                                                    3. Record the times
                                                     and durations of
                                                     all periods during
                                                     batch emission
                                                     episodes when all
                                                     flames at the pilot
                                                     light of a flare
                                                     are absent or the
                                                     monitor is not
                                                     operating.
                                                    4. Report the times
                                                     and durations of
                                                     all periods during
                                                     batch emission
                                                     episodes selected
                                                     for control when
                                                     all flames at the
                                                     pilot light of a
                                                     flare are absent--
                                                     PR.d
Scrubber for halogenated      a. pH of scrubber     1. Continuous
 batch front-end process       effluent, and.        records as
 vents or aggregate batch                            specified in Sec.
 vent streams (Note:                                 63.491(e)(1).b
 Controlled by a combustion                         2. Record and report
 device other than a flare).                         the average pH of
                                                     the scrubber
                                                     effluent measured
                                                     during the
                                                     performance test--
                                                     NCS.c
                                                    3. Record the batch
                                                     cycle daily average
                                                     pH of the scrubber
                                                     effluent as
                                                     specified in Sec.
                                                     63.491(e)(2).
                                                    4. Report all batch
                                                     cycle daily average
                                                     pH values of the
                                                     scrubber effluent
                                                     that are below the
                                                     minimum operating
                                                     value established
                                                     in the NCS or
                                                     operating permit
                                                     and all instances
                                                     when insufficient
                                                     monitoring data
                                                     arecollected--PR.d
                                                     e
                              b. Scrubber liquid    1. Records as
                               and gas flow rates    specified in Sec.
                               (Sec.  63.489(b)(4)   63.491(e)(1).b
                               (ii)).               2. Record and report
                                                     the scrubber liquid/
                                                     gas ratio averaged
                                                     over the full
                                                     period of the
                                                     performance test--
                                                     NCS.c
                                                    3. Record the batch
                                                     cycle daily average
                                                     scrubber liquid/gas
                                                     ratio as specified
                                                     in Sec.
                                                     63.491(e)(2).
                                                    4. Report all batch
                                                     cycle daily average
                                                     scrubber liquid/gas
                                                     ratios that are
                                                     below the minimum
                                                     value established
                                                     in the NCS or
                                                     operating permit
                                                     and all instances
                                                     when insufficient
                                                     monitoring data are
                                                     collected--PR.d e
Absorber \f\................  a. Exit temperature   1. Continuous
                               of the absorbing      records as
                               liquid, and           specified in Sec.
                                                     63.491(e)(1).b

[[Page 36935]]

 
                                                    2. Record and report
                                                     the average exit
                                                     temperature of the
                                                     absorbing liquid
                                                     measured during the
                                                     performance test--
                                                     NCS.\c\
                                                    3. Record the batch
                                                     cycle daily average
                                                     exit temperature of
                                                     the absorbing
                                                     liquid as specified
                                                     in Sec.
                                                     63.491(e)(2) for
                                                     each batch cycle.
                                                    4. Report all the
                                                     batch cycle daily
                                                     average exit
                                                     temperatures of the
                                                     absorbing liquid
                                                     that are above the
                                                     maximum operating
                                                     temperature
                                                     established in the
                                                     NCS or operating
                                                     permit and all
                                                     instances when
                                                     monitoring data are
                                                     not collected--
                                                     PR.d,e
                              b. Exit specific      1. Continuous
                               gravity of the        records as
                               absorbing liquid.     specified in Sec.
                                                     63.491(e)(1).b
                                                    2. Record and report
                                                     the average exit
                                                     specific gravity
                                                     measured during the
                                                     performance test--
                                                     NCS.
                                                    3. Record the batch
                                                     cycle daily average
                                                     exit specific
                                                     gravity as
                                                     specified in Sec.
                                                     63.491(e)(2).
                                                    4. Report all batch
                                                     cycle daily average
                                                     exit specific
                                                     gravity values that
                                                     are below the
                                                     minimum operating
                                                     value established
                                                     in the NCS or
                                                     operating permit
                                                     and all instances
                                                     when monitoring
                                                     data are not
                                                     collected--PR.d e
Condenser \f\...............  Exit (product side)   1. Continuous
                               temperature.          records as
                                                     specified in Sec.
                                                     63.491(e)(1)b
                                                    2. Record and report
                                                     the average exit
                                                     temperature
                                                     measured during the
                                                     performance test--
                                                     NCS.
                                                    3. Record the batch
                                                     cycle daily average
                                                     exit temperature as
                                                     specified in Sec.
                                                     63.491(e)(2).
                                                    4. Report all batch
                                                     cycle daily average
                                                     exit temperatures
                                                     that are above the
                                                     maximum operating
                                                     value established
                                                     in the NCS or
                                                     operating permit
                                                     and all instances
                                                     when monitoring
                                                     data are not
                                                     collected--PR.d e
Carbon adsorber f...........  a. Total              1. Record of total
                               regeneration steam    regeneration steam
                               flow or nitrogen      flow or nitrogen
                               flow, or pressure     flow, or pressure
                               gauge or absolute)    for each carbon bed
                               during carbon bed     regeneration cycle.
                               regeneration
                               cycle(s), and
                                                    2. Record and report
                                                     the total
                                                     regeneration steam
                                                     flow or nitrogen
                                                     flow, or pressure
                                                     during each carbon
                                                     bed regeneration
                                                     cycle during the
                                                     performance test--
                                                     NCS.c
                                                    3. Report all carbon
                                                     bed regeneration
                                                     cycles when the
                                                     total regeneration
                                                     steam flow or
                                                     nitrogen flow, or
                                                     pressure is above
                                                     the maximum value
                                                     established in the
                                                     NCS or operating
                                                     permit--PR.d e
                              b. Temperature of     1. Record the
                               the carbon bed        temperature of the
                               after regeneration    carbon bed after
                               and within 15         each regeneration
                               minutes of            and within 15
                               completing any        minutes of
                               cooling cycle(s).     completing any
                                                     cooling cycle(s).
                                                    2. Record and report
                                                     the temperature of
                                                     the carbon bed
                                                     after each
                                                     regeneration and
                                                     within 15 minutes
                                                     of completing any
                                                     cooling
                                                     cycle(s)measured
                                                     during the
                                                     performance test--
                                                     NCS.c
                                                    3. Report all carbon
                                                     bed regeneration
                                                     cycles when the
                                                     temperature of the
                                                     carbon bed after
                                                     regeneration, or
                                                     within 15 minutes
                                                     of completing any
                                                     cooling cycle(s),
                                                     is above the
                                                     maximum value
                                                     established in the
                                                     NCS or operating
                                                     permit--PR.d e

[[Page 36936]]

 
All control devices.........  a. Diversion to the   1. Hourly records of
                               atmosphere from the   whether the flow
                               control device or     indicator was
                                                     operating during
                                                     batch emission
                                                     episodes selected
                                                     for control and
                                                     whether a diversion
                                                     was detected at any
                                                     time during the
                                                     hour, as specified
                                                     in Sec.
                                                     63.491(e)(3).
                                                    2. Record and report
                                                     the times of all
                                                     periods during
                                                     batch emission
                                                     episodes selected
                                                     for control when
                                                     emissions are
                                                     diverted through a
                                                     bypass line, or the
                                                     flow indicator is
                                                     not operating--PR.d
                              b. Monthly            1. Records that
                               inspections of        monthly inspections
                               sealed valves.        were performed as
                                                     specified in Sec.
                                                     63.491(e)(4)(i).
                                                    2. Record and report
                                                     all monthly
                                                     inspections that
                                                     show that valves
                                                     are in the
                                                     diverting position
                                                     or that a seal has
                                                     been broken--PR.d
Absorber, condenser, and      Concentration level   1. Continuous
 carbon adsorber (as an        or reading            records as
 alternative to the above).    indicated by an       specified in Sec.
                               organic monitoring    63.491(e)(1).b
                               device at the        2. Record and report
                               outlet of the         and average batch
                               recovery device.      vent concentration
                                                     level or reading
                                                     measured during the
                                                     performance test--
                                                     NCS.
                                                    3. Record the batch
                                                     cycle daily average
                                                     concentration level
                                                     or reading as
                                                     specified in Sec.
                                                     63.491(e)(2).
                                                    4. Report all batch
                                                     cycle daily average
                                                     concentration
                                                     levels or readings
                                                     that are above the
                                                     maximum values
                                                     established in the
                                                     NCS or operating
                                                     permit and all
                                                     instances when
                                                     monitoring data are
                                                     not collected--PR.d
                                                     e
------------------------------------------------------------------------
a Monitor may be installed in the firebox or in the duct work
  immediately downstream of the firebox before any substantial heat
  exchange is encountered.
b ``Continuous records'' is defined in Sec.  63.111.
c NCS = Notification of Compliance Status described in Sec.
  63.506(e)(5).
d PR = Periodic Reports described in Sec.  63.506(e)(6).
e The periodic reports shall include the duration of periods when
  monitoring data are not collected as specified in Sec.
  63.506(e)(6)(iii)(C).
f Alternatively, these devices may comply with the organic monitoring
  device provisions listed at the end of this table.

* * * * * * *

                     Table 9 to Subpart U of Part 63
               [Routine reports required by this subpart]
------------------------------------------------------------------------
                                 Description of
          Reference                  report               Due Date
------------------------------------------------------------------------
Sec.  63.506(b) and subpart   Refer to Sec.         Refer to subpart A.
 A.                            63.506(b), Table 1
                               of this subpart,
                               and to subpart A.
Sec.  63.506(e)(3)..........  Precompliance Report  1. Existing affected
                               a.                    sources: December
                                                     19, 2000.
                                                    2. New affected
                                                     sources: with the
                                                     application for
                                                     approval of
                                                     construction or
                                                     reconstruction.
Sec.  63.506(e)(4)..........  Emissions Averaging   September 19, 2000.
                               Plan.
Sec.  63.506(e)(4)(iv)......  Updates to Emissions  120 days prior to
                               Averaging Plan.       making the change
                                                     necessitating the
                                                     update.
Sec.  63.506(e)(5)..........  Notification of        Within 150 days
                               Compliance Status b.  after the
                                                     compliance date.
Sec.  63.506(e)(6)..........  Periodic reports....  Semiannually, no
                                                     later than 60 days
                                                     after the end of
                                                     each 6-month
                                                     period. See Sec.
                                                     63.506(e)(6)(i) for
                                                     the due date for
                                                     this report.
Sec.  63.506(e)(6)(xi)......  Quarterly for         No later than 60
                               reports Emissions     days after the end
                               Averaging.            of each quarter.
                                                     First report is due
                                                     with the
                                                     Notification of
                                                     Compliance Status.
Sec.  63.506(e)(6)(xii).....  Quarterly reports     No later than 60
                               upon request of the   days after the end
                               Administrator.        of each quarter.
Sec.  63.506(e)(7)(i).......  Storage Vessels       At least 30 days
                               Notification of       prior to the
                               Inspection.           refilling of each
                                                     storage vessel or
                                                     the inspection of
                                                     each storage
                                                     vessel.

[[Page 36937]]

 
Sec.  63.506(e)(7)(ii)......  Requests for          Initial submittal is
                               Approval of a         due with the
                               Nominal Control       Emissions Averaging
                               Efficiency for Use    Plan; later
                               in Emissions          submittals are made
                               Averaging.            at the discretion
                                                     of the owner or
                                                     operator as
                                                     specified in Sec.
                                                     63.506(e)(7)(ii)(B)
                                                     .
Sec.  63.506(e)(7)(iii).....  Notification of       For notification
                               Change in the         under Sec.
                               Primary Product.      63.480(f)(3)(ii)--n
                                                     otification
                                                     submittal date at
                                                     the discretion of
                                                     the owner or
                                                     operator.c
                                                    For notification
                                                     under Sec.
                                                     63.480(f)(4)(ii)--w
                                                     ithin 6 months of
                                                     making the
                                                     determination.
------------------------------------------------------------------------
a There may be two versions of this report due at different times; one
  for equipment subject to Sec.  63.502 and one for other emission
  points subject to this subpart.
b There will be two versions of this report due at different times; one
  for equipment subject to Sec.  63.502 and one for other emission
  points subject to this subpart.
c Note that the EPPU remains subject to this subpart until the
  notification under Sec.  63.480(f)(3)(i) is made.

Subpart JJJ--National Emission Standards for Hazardous Air 
Pollutant Emissions: Group IV Polymers and Resins

    10. Section 63.1310 is amended by revising paragraphs (i)(1)(i) 
introductory text and (i)(2)(ii) and (iii) to read as follows:


Sec. 63.1310  Applicability and designation of affected sources.

* * * * *
    (i) * * *
    (1) * * *
    (i) If a group of one or more TPPUs that produce the same primary 
product is added to a plant site, the added group of one or more TPPUs 
and associated equipment, as listed in paragraph (a)(4) of this 
section, shall be a new affected source and shall comply with the 
requirements for a new affected source in this subpart upon initial 
start-up or by June 19, 2000, whichever is later, except that new 
affected sources whose primary product, as determined using the 
procedures specified in paragraph (f) of this section, is poly(ethylene 
terephthalate) (PET) shall be in compliance with Sec. 63.1331 upon 
initial start-up or February 27, 2001, whichever is later, if the added 
group of one or more TPPUs meets the criteria in either paragraph 
(i)(1)(i)(A) or (i)(1)(i)(B) of this section, and the criteria in 
either paragraph (i)(1)(i)(C) or (i)(1)(i)(D) of this section are met.
* * * * *
    (2) * * *
    (ii) If any components are replaced at an existing affected source 
such that the criteria specified in paragraphs (i)(2)(i)(A) through 
(i)(2)(i)(B) of this section are not met, and that replacement of 
components creates one or more Group 1 emission points (i.e., either 
newly created Group 1 emission points or emission points that change 
group status from Group 2 to Group 1) or causes any other emission 
point to be added (i.e., Group 2 emission points, equipment leak 
components subject to Sec. 63.1331, continuous process vents subject to 
Secs. 63.1316 through 63.1320, and heat exchange systems subject to 
Sec. 63.1328), the resulting emission point(s) shall be subject to the 
applicable requirements for an existing affected source. The resulting 
emission points shall be in compliance by 120 days after the date of 
initial start-up or by the appropriate compliance date specified in 
Sec. 63.1311 (i.e., February 27, 1998 for most equipment leak 
components subject to Sec. 63.1331, and June 19, 2001 for most emission 
points other than equipment leaks), whichever is later.
    (iii) If an addition or process change (not including a process 
change that solely replaces components) is made to an existing affected 
source that creates one or more Group 1 emission points (i.e., either 
newly created Group 1 emission points or emission points that change 
group status from Group 2 to Group 1) or causes any other emission 
point to be added (i.e., Group 2 emission points, equipment leak 
components subject to Sec. 63.1331, continuous process vents subject to 
Secs. 63.1316 through 63.1320, and heat exchange systems subject to 
Sec. 63.1328), the resulting emission point(s) shall be subject to the 
applicable requirements for an existing affected source. The resulting 
emission point(s) shall be in compliance by 120 days after the date of 
initial start-up or by the appropriate compliance date specified in 
Sec. 63.1311 (i.e., February 27, 1998 for most equipment leak 
components subject to Sec. 63.1331, and June 19, 2001 for most emission 
points other than equipment leaks), whichever is later.
* * * * *

    11. Section 63.1311 is amended by revising paragraph (b) to read as 
follows:


Sec. 63.1311  Compliance dates and relationship of this subpart to 
existing applicable rules.

* * * * *
    (b) New affected sources that commence construction or 
reconstruction after March 29, 1995 shall be in compliance with this 
subpart upon initial start-up or by June 19, 2000, whichever is later, 
except that new affected sources whose primary product, as determined 
using the procedures specified in Sec. 63.1310(f), is PET shall be in 
compliance with Sec. 63.1331 upon initial start-up or August 27, 2001, 
whichever is later.
* * * * *

    12. Section 63.1312(b) is amended by revising the definitions for 
the terms ``Group 1 wastewater stream'' and ``Reconstruction.''


Sec. 63.1312  Definitions.

* * * * *
    (b) * * *
    Group 1 wastewater stream means a wastewater stream consisting of 
process wastewater from an existing or new affected source that meets 
the criteria for Group 1 status in Sec. 63.132(c) and/or that meets the 
criteria for Group 1 status in Sec. 63.132(d), with the exceptions 
listed in Sec. 63.1330(b)(8) for the purposes of this subpart (i.e., 
for organic HAP as defined in this section).
* * * * *
    Reconstruction means the replacement of components of an affected 
source or of a previously unaffected stationary source that becomes an 
affected source as a result of the replacement, to such an extent that:
    (1) The fixed capital cost of the new components exceeds 50 percent 
of the fixed capital cost that would be required

[[Page 36938]]

to construct a comparable new source; and
    (2) It is technologically and economically feasible for the 
reconstructed source to meet the provisions of this subpart.
* * * * *

    13. Section 63.1315 is amended by revising paragraphs (a)(9) and 
(d) to read as follows:


Sec. 63.1315  Continuous process vents provisions.

* * * * *
    (a) * * *
    (9) When Sec. 63.114(e) or Sec. 63.117(f) specifies that an owner 
or operator shall submit the information required in Sec. 63.152(b) in 
order to establish the parameter monitoring range, the owner or 
operator of an affected source shall comply with the provisions of 
Sec. 63.1335(e)(5) for purposes of reporting information related to 
establishment of the parameter monitoring level for purposes of this 
subpart. Further, the term ``level'' shall apply when the term 
``range'' is used in Secs. 63.114, 63.117, and 63.118.
* * * * *
    (d) Affected sources producing PET or polystyrene using a 
continuous process are subject to the emissions control provisions of 
Sec. 63.1316, the monitoring provisions of Sec. 63.1317, the testing 
and compliance demonstration provisions of Sec. 63.1318, the 
recordkeeping provisions of Sec. 63.1319, and the reporting provisions 
of Sec. 63.1320. However, in some instances as specified in 
Sec. 63.1316, select continuous process vents present at affected 
sources producing PET or polystyrene using a continuous process are 
subject to the provisions of this section.
* * * * *

    14. Section 63.1316 is amended by revising paragraph (b)(1)(i)(B) 
to read as follows:


Sec. 63.1316  PET and polystyrene affected sources--emissions control 
provisions.

* * * * *
    (b) * * *
    (1) * * *
    (i) * * *
    (B) As specified in Sec. 63.1318(d), the owner or operator shall 
maintain the daily average outlet gas stream temperature from each 
final condenser in a material recovery section at a temperature of 
+3 deg.C (+37 deg.F) or less (i.e., colder); or
* * * * *

    15. Section 63.1318 is amended by revising paragraph (a) to read as 
follows:


Sec. 63.1318  PET and polystyrene affected sources--testing and 
compliance demonstration provisions.

    (a) Except as specified in paragraphs (b) through (d) of this 
section, continuous process vents using a control or recovery device to 
comply with Sec. 63.1316 shall comply with the applicable testing and 
compliance provisions for continuous process vents specified in 
Sec. 63.1315(a) except that, for purposes of this paragraph (a), 
references to group determinations (i.e., total resource effectiveness) 
do not apply and owners or operators are not required to comply with 
Sec. 63.113.
* * * * *

    16. Section 63.1319 is amended in paragraph (a) by revising the 
reference to ``Sec. 63.1315'' to read ``Sec. 63.1315(a).''

    17. Section 63.1320 is amended in paragraph (a) by revising the 
reference to ``Sec. 63.1315'' to read ``Sec. 63.1315(a).'' and by 
revising paragraph (b)(3) to read as follows:


Sec. 63.1320  PET and polystyrene affected sources--reporting 
provisions.

* * * * *
    (b) * * *
    (3) Whenever a process change, as defined in Sec. 63.115(e), is 
made that causes emissions from continuous process vents in the 
collection of material recovery sections (i.e., methanol recovery) 
within the affected source to be greater than 0.12 kg organic HAP per 
Mg of product, the owner or operator shall submit a report within 180 
days after the process change is made or the information regarding the 
process change is known to the owner or operator. This report may be 
included in the next Periodic Report. The report shall include the 
information specified in Sec. 63.1319(b)(1) and a description of the 
process change.
* * * * *

    18. Section 63.1322 is amended in paragraphs (f)(1)(ii) and 
(g)(1)(ii) by revising the references to ``Sec. 63.1335(e)(5)(iv)'' to 
read ``Sec. 63.1335(e)(5)(viii).''

    19. Section 63.1323 is amended in paragraph (b)(6)(i)(C) by 
revising the reference to ``Sec. 63.506(e)(3)'' to read 
``Sec. 63.1335(e)(3),'' and by revising paragraph (h)(1) introductory 
text to read as follows:


Sec. 63.1323  Batch process vents--methods and procedures for group 
determination.

* * * * *
    (h) * * *
    (1) The concentration of each organic compound containing halogen 
atoms (ppmv, by compound) for each batch emission episode shall be 
determined after the last recovery device (if any recovery devices are 
present), based on any one of the following procedures:
* * * * *

    20. Section 63.1324 is amended by revising paragraph (f)(1)(ii) to 
read as follows:


Sec. 63.1324  Batch process vents--monitoring equipment.

* * * * *
    (f) * * *
    (1) * * *
    (ii) For aggregate batch vent streams using a control device to 
comply with Sec. 63.1322(b)(2), the established level shall reflect the 
emission reduction requirement of either 90 percent or 20 ppmv 
specified in Sec. 63.1322(b)(2).
* * * * *

    21. Section 63.1327 is amended in paragraph (b) by revising the 
reference to ``Sec. 63.480(i)(2)(ii)'' to read 
``Sec. 63.1310(i)(2)(ii).''

    22. Section 63.1330 is amended as follows:
    a. By revising paragraph (a);
    b. By revising paragraph (b)(8)(i);
    c. By revising paragraph (b)(8)(ii);
    d. By adding paragraph (d); and
    e. By adding paragraph (e).
    The revisions and additions read as follows:


Sec. 63.1330  Wastewater provisions.

* * * * *
    (a) Except as specified in paragraphs (d) and (e) of this section, 
the owner or operator of each affected source shall comply with 
paragraphs (b) and (c) of this section.
    (b) * * *
    (8) * * *
    (i) When Secs. 63.132 through 63.149 refer to table 8 compounds, 
the owner or operator is only required to consider 1,3-butadiene for 
purposes of this subpart.
    (ii) When Secs. 63.132 through 63.149 refer to table 9 compounds, 
the owner or operator is only required to consider compounds that meet 
the definition of organic HAP in Sec. 63.1312 and that are listed on 
table 9 of 40 CFR part 63, subpart G, for the purposes of this subpart, 
except for ethylene glycol which need not be considered.
* * * * *
    (d) The provisions of paragraph (b) of this section do not apply to 
each affected source producing ASA/AMSAN.
    (e) The provisions of paragraphs (b) and (c) of this section do not 
apply to each affected source producing polystyrene using either a 
continuous or batch process.

    23. Section 63.1335 is amended as follows:

[[Page 36939]]

    a. By revising paragraph (e)(5)(i) introductory text;
    b. By revising (e)(7)(ii)(A); and
    c. By revising (e)(7)(ii)(B).
    The revisions read as follows:


Sec. 63.1335  General recordkeeping and reporting provisions.

* * * * *
    (e) * * *
    (5) * * *
    (i) The results of any emission point group determinations, process 
section applicability determinations, performance tests, inspections, 
any other information used to demonstrate compliance, values of 
monitored parameters established during performance tests, and any 
other information required to be included in the Notification of 
Compliance Status under Secs. 63.1311(m), 63.122, and 63.1314 for 
storage vessels, Sec. 63.117 for continuous process vents, Sec. 63.146 
for process wastewater, Secs. 63.1316 through 63.1320 for continuous 
process vents subject to Sec. 63.1316, Sec. 63.1327 for batch process 
vents, Sec. 63.1329 for process contact cooling towers, and 
Sec. 63.1332 for emission points included in an emissions average. In 
addition, the owner or operator of an affected source shall comply with 
paragraphs (e)(5)(i)(A) and (e)(5)(i)(B) of this section.
* * * * *
    (7) * * *
    (i) * * *
    (ii) * * *
    (A) If use of a nominal control efficiency is part of the initial 
Emissions Averaging Plan described in paragraph (e)(4)(ii) of this 
section, the information shall be submitted with the Emissions 
Averaging Plan.
    (B) If an owner or operator elects to use a nominal control 
efficiency after submittal of the initial Emissions Averaging Plan as 
described in paragraph (e)(4)(ii) of this section, the information 
shall be submitted at the discretion of the owner or operator.
* * * * *

    24. Revising Tables 1, 6, 7, and 9 to Subpart JJJ of Part 63, to 
read as follows:

                                        Table 1 to Subpart JJJ of Part 63
                      [Applicability of general provisions to subpart JJJ affected sources]
----------------------------------------------------------------------------------------------------------------
                 Reference                    Applies to  Subpart JJJ                  Explanation
----------------------------------------------------------------------------------------------------------------
Sec.  63.1(a)(1)...........................  Yes......................  Sec.  63.1312 specifies definitions in
                                                                         addition to or that supersede
                                                                         definitions in Sec.  63.2.
Sec.  63.1(a)(2)...........................  Yes......................
Sec.  63.1(a)(3)...........................  Yes......................  Sec.  63.1311(g) through (l) and Sec.
                                                                         63.160(b) identify those standards
                                                                         which may apply in addition to the
                                                                         requirements of subparts JJJ and H of
                                                                         this part, and specify how compliance
                                                                         shall be achieved.
Sec.  63.1(a)(4)...........................  Yes......................  Subpart JJJ (this table) specifies the
                                                                         applicability of each paragraph in
                                                                         subpart A to subpart JJJ.
Sec.  63.1(a)(5)...........................  No.......................  [Reserved.].
Sec.  63.1(a)(6)-(8).......................  Yes......................
Sec.  63.1(a)(9)...........................  No.......................  [Reserved.].
Sec.  63.1(a)(10)..........................  Yes......................
Sec.  63.1(a)(11)..........................  Yes......................
Sec.  63.1(a)(12)-(14).....................  Yes......................
Sec.  63.1(b)(1)...........................  No.......................  Sec.  63.1310(a) contains specific
                                                                         applicability criteria.
Sec.  63.1(b)(2)...........................  Yes......................
Sec.  63.1(b)(3)...........................  No.......................  Sec.  63.1310(b) provides documentation
                                                                         requirements for TPPUs not considered
                                                                         affected sources.
Sec.  63.1(c)(1)...........................  Yes......................  Subpart JJJ (this table) specifies the
                                                                         applicability of each paragraph in
                                                                         subpart A to subpart JJJ.
Sec.  63.1(c)(2)...........................  No.......................  Area sources are not subject to subpart
                                                                         JJJ.
Sec.  63.1(c)(3)...........................  No.......................  [Reserved.].
Sec.  63.1(c)(4)...........................  Yes......................
Sec.  63.1(c)(5)...........................  Yes......................  Except that affected sources are not
                                                                         required to submit notifications that
                                                                         are not required by subpart JJJ.
Sec.  63.1(d)..............................  No.......................  [Reserved.].
Sec.  63.1(e)..............................  Yes......................
Sec.  63.2.................................  Yes......................  Sec.  63.1312 specifies those subpart A
                                                                         definitions that apply to subpart JJJ.
Sec.  63.3.................................  Yes......................
Sec.  63.4(a)(1)-(3).......................  Yes......................
Sec.  63.4(a)(4)...........................  No.......................  [Reserved.].
Sec.  63.4(a)(5)...........................  Yes......................
Sec.  63.4(b)..............................  Yes......................
Sec.  63.4(c)..............................  Yes......................
Sec.  63.5(a)(1)...........................  Yes......................  Except the terms ``source'' and
                                                                         ``stationary source'' should be
                                                                         interpreted as having the same meaning
                                                                         as ``affected source.''
Sec.  63.5(a)(2)...........................  Yes......................
Sec.  63.5(b)(1)...........................  Yes......................  Except Sec.  63.1310(i) defines when
                                                                         construction or reconstruction is
                                                                         subject to new source standards.
Sec.  63.5(b)(2)...........................  No.......................  [Reserved.].
Sec.  63.5(b)(3)...........................  Yes......................
Sec.  63.5(b)(4)...........................  Yes......................  Except that the Initial Notification and
                                                                         Sec.  63.9(b) requirements do not
                                                                         apply.
Sec.  63.5(b)(5)...........................  Yes......................
Sec.  63.5(b)(6)...........................  Yes......................  Except that Sec.  63.1310(i) defines
                                                                         when construction or reconstruction is
                                                                         subject to new source standards.
Sec.  63.5(c)..............................  No.......................  [Reserved.]
Sec.  63.5(d)(1)(i)........................  Yes......................  Except that the references to the
                                                                         Initial Notification and Sec.
                                                                         63.9(b)(5) do not apply.
Sec.  63.5(d)(1)(ii).......................  Yes......................  Except that Sec.  63.5(d)(1)(ii)(H) does
                                                                         not apply.

[[Page 36940]]

 
Sec.  63.5(d)(1)(iii)......................  No.......................  Secs.  63.1335(e)(5) and 63.1331(a)(4)
                                                                         specify Notification of Compliance
                                                                         Status requirements.
Sec.  63.5(d)(2)...........................  No.......................
Sec.  63.5(d)(3)...........................  Yes......................  Except Sec.  63.5(d)(3)(ii) does not
                                                                         apply, and equipment leaks subject to
                                                                         Sec.  63.1331 are exempt.
Sec.  63.5(d)(4)...........................  Yes......................
Sec.  63.5(e)..............................  Yes......................
Sec.  63.5(f)(1)...........................  Yes......................
Sec.  63.5(f)(2)...........................  Yes......................  Except that where Sec.  63.9(b)(2) is
                                                                         referred to, the owner or operator need
                                                                         not comply.
Sec.  63.6(a)..............................  Yes......................
Sec.  63.6(b)(1)...........................  No.......................  The dates specified in Sec.  63.1311(b)
                                                                         apply, instead.
Sec.  63.6(b)(2)...........................  No.......................
Sec.  63.6(b)(3)...........................  No.......................
Sec.  63.6(b)(4)...........................  No.......................
Sec.  63.6(b)(5)...........................  No.......................
Sec.  63.6(b)(6)...........................  No.......................  [Reserved.].
Sec.  63.6(b)(7)...........................  No.......................
Sec.  63.6(c)(1)...........................  Yes......................  Except that Sec.  63.1311 specifies the
                                                                         compliance date.
Sec.  63.6(c)(2)...........................  No.......................
Sec.  63.6(c)(3)...........................  No.......................  [Reserved.].
Sec.  63.6(c)(4)...........................  No.......................  [Reserved.].
Sec.  63.6(c)(5)...........................  Yes......................
Sec.  63.6(d)..............................  No.......................  [Reserved.].
Sec.  63.6(e)..............................  Yes......................  Except as otherwise specified for
                                                                         individual paragraphs. Does not apply
                                                                         to Group 2 emissionpoints, unless they
                                                                         are included in an emissions average.a
Sec.  63.6(e)(1)(i)........................  No.......................  This is addressed by Sec.
                                                                         63.1310(j)(4).
Sec.  63.6(e)(1)(ii).......................  Yes......................
Sec.  63.6(e)(1)(iii)......................  Yes......................
Sec.  63.6(e)(2)...........................  Yes......................
Sec.  63.6(e)(3)(i)........................  Yes......................  For equipment leaks (subject to Sec.
                                                                         63.1331), the start-up, shutdown, and
                                                                         malfunction plan requirement of Sec.
                                                                         63.6(e)(3)(i) is limited to control
                                                                         devices and is optional for other
                                                                         equipment. The start-up, shutdown,
                                                                         malfunction plan may include written
                                                                         procedures that identifyconditions that
                                                                         justify a delay of repair.
Sec.  63.6(e)(3)(i)(A).....................  No.......................  This is addressed by Sec.
                                                                         63.1310(j)(4).
Sec.  63.6(e)(3)(i)(B).....................  Yes......................
Sec.  63.6(e)(3)(i)(C).....................  Yes......................
Sec.  63.6(e)(3)(ii).......................  Yes......................
Sec.  63.6(e)(3)(iii)......................  No.......................  Recordkeeping and reporting are
                                                                         specified in Sec.  63.1335(b)(1).
Sec.  63.6(e)(3)(iv).......................  No.......................  Recordkeeping and reporting are
                                                                         specified in Sec.  63.1335(b)(1).
Sec.  63.6(e)(3)(v)........................  Yes......................
Sec.  63.6(e)(3)(vi).......................  Yes......................
Sec.  63.6(e)(3)(vii)......................  Yes......................
Sec.  63.6(e)(3)(vii)(A)...................  Yes......................
Sec.  63.6(e)(3)(vii)(B)...................  Yes......................  Except the plan shall provide for
                                                                         operation in (B) compliance with Sec.
                                                                         63.1310(j)(4).
Sec.  63.6(e)(3)(vii)(C)...................  Yes......................
Sec.  63.6(e)(3)(viii).....................  Yes......................
Sec.  63.6(f)(1)...........................  Yes......................
Sec.  63.6(f)(2)...........................  Yes......................  Except Sec.  63.7(c), as referred to in
                                                                         Sec.  63.6(f)(2)(iii)(D), does not
                                                                         apply, and except that Sec.
                                                                         63.6(f)(2)(ii) does not apply to
                                                                         equipment leaks subject to Sec.
                                                                         63.1331.
Sec.  63.6(f)(3)...........................  Yes......................
Sec.  63.6(g)..............................  Yes......................
Sec.  63.6(h)..............................  No.......................  Subpart JJJ does not require opacity and
                                                                         visible emission standards.
Sec.  63.6(i)(1)...........................  Yes......................
Sec.  63.6(i)(2)...........................  Yes......................
Sec.  63.6(i)(3)...........................  Yes......................
Sec.  63.6(i)(4)(i)(A).....................  Yes......................
Sec.  63.6(i)(4)(i)(B).....................  No.......................  Dates are specified in Sec.  63.1311(e)
                                                                         and Sec.  63.1335(e)(3)(i).
Sec.  63.6(i)(4)(ii).......................  No.......................
Sec.  63.6(i)(5)-(14)......................  Yes......................
Sec.  63.6(i)(15)..........................  No.......................  [Reserved.].
Sec.  63.6(i)(16)..........................  Yes......................
Sec.  63.6(j)..............................  Yes......................
Sec.  63.7(a)(1)...........................  Yes......................
Sec.  63.7(a)(2)...........................  No.......................  Sec.  63.1335(e)(5) specifies the
                                                                         submittal dates of performance test
                                                                         results for all emission points except
                                                                         equipment leaks; for equipment leaks,
                                                                         compliance demonstration results are
                                                                         reported in the Periodic Reports.
Sec.  63.7(a)(3)...........................  Yes......................
Sec.  63.7(b)..............................  No.......................  Sec.  63.1333(a)(4) specifies
                                                                         notification requirements.
Sec.  63.7(c)..............................  No.......................

[[Page 36941]]

 
Sec.  63.7(d)..............................  Yes......................
Sec.  63.7(e)(1)...........................  Yes......................  Except that all performance tests shall
                                                                         be conducted at maximum representative
                                                                         operating conditions achievable at the
                                                                         time without disruption of operations
                                                                         or damage to equipment.
Sec.  63.7(e)(2)...........................  Yes......................
Sec.  63.7(e)(3)...........................  No.......................  Subpart JJJ specifies requirements.
Sec.  63.7(e)(4)...........................  Yes......................
Sec.  63.7(f)..............................  Yes......................  Except that Sec.  63.144(b)(5)(iii)(A)
                                                                         and (B) shall apply for process
                                                                         wastewater. Also, because a site
                                                                         specific test plan is not required, the
                                                                         notification deadline in Sec.
                                                                         63.7(f)(2)(i) shall be 60 days prior to
                                                                         the performance test, and in Sec.
                                                                         63.7(f)(3), approval or disapproval of
                                                                         the alternative test method shall not
                                                                         be tied to the site specific test plan.
Sec.  63.7(g)..............................  Yes......................  Except that the requirements in Sec.
                                                                         63.1335(e)(5) shall apply instead of
                                                                         references to the Notification of
                                                                         Compliance Status report in Sec.
                                                                         63.9(h). In addition, equipment leaks
                                                                         subject to Sec.  63.1331 are not
                                                                         required to conduct performance tests.
Sec.  63.7(h)..............................  Yes......................  Except Sec.  63.7(h)(4)(ii) is not
                                                                         applicable, because the site-specific
                                                                         test plans in Sec.  63.7(c)(2) are not
                                                                         required.
Sec.  63.8(a)(1)...........................  Yes......................
Sec.  63.8(a)(2)...........................  No.......................
Sec.  63.8(a)(3)...........................  No.......................  [Reserved.].
Sec.  63.8(a)(4)...........................  Yes......................
Sec.  63.8(b)(1)...........................  Yes......................
Sec.  63.8(b)(2)...........................  No.......................  Subpart JJJ specifies locations to
                                                                         conduct monitoring.
Sec.  63.8(b)(3)...........................  Yes......................
Sec.  63.8(c)(1)...........................  Yes......................
Sec.  63.8(c)(1)(i)........................  Yes......................
Sec.  63.8(c)(1)(ii).......................  No.......................  For all emission points except equipment
                                                                         leaks, comply with Sec.
                                                                         63.1335(b)(1)(i)(B); for equipment
                                                                         leaks, comply with Sec.
                                                                         63.181(g)(2)(iii).
Sec.  63.8(c)(1)(iii)......................  Yes......................
Sec.  63.8(c)(2)...........................  Yes......................
Sec.  63.8(c)(3)...........................  Yes......................
Sec.  63.8(c)(4)...........................  No.......................  Sec.  63.1334 specifies monitoring
                                                                         frequency; not applicable to equipment
                                                                         leaks because Sec.  63.1331 does not
                                                                         require continuous monitoring systems.
Sec.  63.8(c)(5)-(8).......................  No.
Sec.  63.8(d)..............................  No.
Sec.  63.8(e)..............................  No.
Sec.  63.8(f)(1)-(3).......................  Yes.
Sec.  63.8(f)(4)(i)........................  No.......................  Timeframe for submitting request is
                                                                         specified in Sec.  63.1335(f) or (g);
                                                                         not applicable to equipment leaks
                                                                         because Sec.  63.1331 (through
                                                                         reference to subpart H) specifies
                                                                         acceptable alternative methods.
Sec.  63.8(f)(4)(ii).......................  No.......................  Contents of requests are specified in
                                                                         Sec.  63.1335(f) or (g).
Sec.  63.8(f)(4)(iii)......................  No.
Sec.  63.8(f)(5)(i)........................  Yes.
Sec.  63.8(f)(5)(ii).......................  No.
Sec.  63.8(f)(5)(iii)......................  Yes.
Sec.  63.8(f)(6)...........................  No.......................  Subpart JJJ does not require continuous
                                                                         emission monitors.
Sec.  63.8(g)..............................  No.......................  Data reduction procedures specified in
                                                                         Sec.  63.1335(d) and (h); not
                                                                         applicable to equipment leaks.
Sec.  63.9(a)..............................  Yes.
Sec.  63.9(b)..............................  No.......................  Subpart JJJ does not require an initial
                                                                         notification.
Sec.  63.9(c)..............................  Yes.
Sec.  63.9(d)..............................  Yes.
Sec.  63.9(e)..............................  No.......................  Sec.  63.1333(a)(4) specifies
                                                                         notification deadline.
Sec.  63.9(f)..............................  No.......................  Subpart JJJ does not require opacity and
                                                                         visible emission standards.
Sec.  63.9(g)..............................  No.
Sec.  63.9(h)..............................  No.......................  Sec.  63.1335(e)(5) specifies
                                                                         Notification of Compliance Status
                                                                         requirements.
Sec.  63.9(i)..............................  Yes.
Sec.  63.9(j)..............................  No.
Sec.  63.10(a).............................  Yes.
Sec.  63.10(b)(1)..........................  No.......................  Sec.  63.1335(a) specifies record
                                                                         retention requirements.
Sec.  63.10(b)(2)..........................  No.......................  Subpart JJJ specifies recordkeeping
                                                                         requirements.
Sec.  63.10(b)(3)..........................  No.......................  Sec.  63.1310(b) requires documentation
                                                                         of sources that are not affected
                                                                         sources.
Sec.  63.10(c).............................  No.......................  Sec.  63.1335 specifies recordkeeping
                                                                         requirements.
Sec.  63.10(d)(1)..........................  Yes.
Sec.  63.10(d)(2)..........................  No.......................  Sec.  63.1335(e) specifies performance
                                                                         test reporting requirements; not
                                                                         applicable to equipment leaks.
Sec.  63.10(d)(3)..........................  No.......................  Subpart JJJ does not require opacity and
                                                                         visible emission standards.
Sec.  63.10(d)(4)..........................  Yes.

[[Page 36942]]

 
Sec.  63.10(d)(5)(i).......................  Yes......................  Except that reports required by Sec.
                                                                         63.10(d)(5)(i) may be submitted at the
                                                                         same time as Periodic Reports specified
                                                                         in Sec.  63.1335(e)(6). The start-up,
                                                                         shutdown, and malfunction plan, and any
                                                                         records or reports of start-up,
                                                                         shutdown, and malfunction do not apply
                                                                         to Group 2 emission points unless they
                                                                         are included in an emissions average.
Sec.  63.10(d)(5)(ii)......................  No.
Sec.  63.10(e).............................  No.......................  Sec.  63.1335 specifies reporting
                                                                         requirements.
Sec.  63.10(f).............................  Yes.
Sec.  63.11................................  Yes......................  Sec.  63.11(b) specifies requirements
                                                                         for flares used to comply with
                                                                         provisions of this subpart. Sec.
                                                                         63.1333(e) contains the requirements to
                                                                         conduct compliance demonstrations for
                                                                         flares subject to this subpart.
Sec.  63.12................................  Yes......................  Except that the authority of Sec.
                                                                         63.1332(i) and the authority of Sec.
                                                                         63.177 (for equipment leaks) shall not
                                                                         be delegated to States.
Secs.  63.13-63.15.........................  Yes.
----------------------------------------------------------------------------------------------------------------
a The plan and any records or reports of start-up, shutdown, and malfunction do not apply to Group 2 emission
  points unless they are included in an emissions average.

* * * * * * *

                                                            Table 6 to Subpart JJJ of Part 63
                                        [Known organic HAP emitted from the production of thermoplastic products]
--------------------------------------------------------------------------------------------------------------------------------------------------------
                                                                                Organic HAP/chemical name  (CAS No.)
                                           -------------------------------------------------------------------------------------------------------------
     Thermoplastic product/Subcategory          Acet-        Acrylo-      1,3 Buta-                   Ethylene                Methyl metha-
                                            aldehyde (75- nitrile (107-  diene (106-   1,4-Dioxane  Glycol (107-   Methanol   crylate (80-  Styrene (100-
                                                07-0)         13-1)         99-0)      (123-91-1)      21-1)      (67-56-1)       62-6)         42-5)
--------------------------------------------------------------------------------------------------------------------------------------------------------
ABS latex.................................                                                                                        
ABS using a batch emulsion process........                                                                                        
ABS using a batch suspension process......                                                                                        
ABS using a continuous emulsion process...                                                                                        
ABS using a continuous mass process.......                                                                                        
ASA/AMSAN.................................                                                                                               
EPS.......................................                                                                                                      
MABS......................................                                                                                        
MBS.......................................                                                                                        
Nitrile resin.............................                    
PET using a batch dimethyl terephthalate                                                        
 process..................................
PET using a batch terephthalic acid                                                       
 process..................................
PET using a continuous dimethyl                                                                 
 terephthalate process....................
PET using a continuous terephthalic acid                                                  
 process..................................
PET using a continuous terephthalic acid                                                  
 high viscosity multiple end finisher
 process..................................
Polystyrene resin using a batch process...                                                                                                      
Polystyrene resin using a continuous                                                                                                            
 process..................................
SAN using a batch process.................                                                                                               
SAN using a continuous process............                                                                                               
--------------------------------------------------------------------------------------------------------------------------------------------------------
 CAS No. = Chemical Abstract Service Number.
 ABS = Acrylonitrile butadiene styrene resin.

[[Page 36943]]

 
 ASA/AMSAN = Acrylonitrile styrene resin/alpha methyl styrene acrylonitrile resin.
 EPS = expandable polystyrene resin.
 MABS = methyl methacrylate acrylonitrile butadiene styrene resin.
 PET = poly(ethylene terephthalate) resin.
 SAN = styrene acrylonitrile resin.
 MBS = methyl methacrylate butadiene styrene resin.


                                        Table 7 of Subpart JJJ of Part 63
     [Group 1 batch process vents and aggregate batch vent streams--monitoring, recordkeeping, and reporting
                                                  requirements]
----------------------------------------------------------------------------------------------------------------
                                                                        Recordkeeping and reporting requirements
            Control device                Parameters to be monitored            for monitored parameters
----------------------------------------------------------------------------------------------------------------
Thermal incinerator...................  Firebox temperature a.........  1. Continuous records as specified in
                                                                         Sec.  63.1326(e)(1).b
                                                                        2. Record and report the average firebox
                                                                         temperature measured during the
                                                                         performance test--NCS.c
                                                                        3. Record the batch cycle daily average
                                                                         firebox temperature as specified in
                                                                         Sec.  63.1326(e)(2).
                                                                        4. Report all batch cycle daily average
                                                                         temperatures that are below the minimum
                                                                         operating value established in the NCS
                                                                         or operating permit and all instances
                                                                         when monitoring data are not collected--
                                                                         PR.d e
Catalytic incinerator.................  Temperature upstream and        1. Continuous records as specified in
                                         downstream of the catalyst      Sec.  63.1326(e)(1).b
                                         bed.                           2. Record and report the average
                                                                         upstream and bed downstream
                                                                         temperatures and the average
                                                                         temperature difference across the
                                                                         catalyst bedmeasured during the
                                                                         performance test--NCS.c
                                                                        3. Record the batch cycle daily average
                                                                         upstream temperature and temperature
                                                                         difference across catalyst bed as
                                                                         specified in Sec.  63.1326(e)(2).
                                                                        4. Report all batch cycle daily average
                                                                         upstream temperatures that are below
                                                                         the minimum upstream value established
                                                                         in the NCS or operating permit--PR.d e
                                                                        5. Report all batch cycle daily average
                                                                         temperature differences across the
                                                                         catalyst bed that are below the minimum
                                                                         difference established in the NCS or
                                                                         operating permit--PR.d,e
                                                                        6. Report all instances when monitoring
                                                                         data are not collected.e
Boiler or Process Heater with a design  Firebox temperature a.........  1. Continuous records as specified in
 heat input capacity less than 44                                        Sec.  63.1326(e)(1).b
 megawatts and where the batch process                                  2. Record and report the average firebox
 vents or aggregate batch vent streams                                   temperature measured during the
 are not introduced with or used as                                      performance test--NCS.c
 the primary fuel.                                                      3. Record the batch cycle daily average
                                                                         firebox temperature as specified in
                                                                         Sec.  63.1326(e)(2).d
                                                                        4. Report all batch cycle daily average
                                                                         temperatures that are below the minimum
                                                                         operating value established in the NCS
                                                                         or operating permit and all instances
                                                                         when monitoring data are not collected--
                                                                         PR.d e
Flare.................................  Presence of a flame at the      1. Hourly records of whether the monitor
                                         pilot light.                    was continuously operating during batch
                                                                         emission episodes, or portions thereof,
                                                                         selected for control and whether a
                                                                         flame was continuously present at the
                                                                         pilot light during said periods.
                                                                        2. Record and report the presence of a
                                                                         flame at the pilot light over the full
                                                                         period of the compliance determination--
                                                                         NCS.c
                                                                        3. Record the times and durations of all
                                                                         periods during batch emission episodes,
                                                                         or portions thereof, selected for
                                                                         control when all flames at the pilot
                                                                         light of a flare are absent or the
                                                                         monitor is not operating.
                                                                        4. Report the times and durations of all
                                                                         periods during batch emission episodes,
                                                                         or portions thereof, selected for
                                                                         control when all flames at the pilot
                                                                         light of a flare are absent--PR.d
Scrubber for halogenated batch process  a. pH of scrubber effluent,     1. Continuous records as specified in
 vents or aggregate batch vent           and.                            Sec.  63.1326(e)(1).b
 strreams (Note: Controlled by a                                        2. Record and report the average pH of
 combustion device other than a flare).                                  the scrubber effluent measured during
                                                                         the performance test--NCS.c
                                                                        3. Record the batch cycle daily average
                                                                         pH of the scrubber effluent as
                                                                         specified in Sec.  63.1326(e)(2).
                                                                        4. Report all batch cycle daily average
                                                                         pH values of the scrubber effluent that
                                                                         are below the minimum operating value
                                                                         established in the NCS or operating
                                                                         permit and all instances when
                                                                         monitoring data are not collected--PR.d
                                                                         e
                                        b. Scrubber liquid and gas      1. Records as specified in Sec.
                                         flow rates.                     63.1326(e)(1).b
                                                                        2. Record and report the scrubber liquid/
                                                                         gas ratio averaged over the full period
                                                                         of the performance test--NCS.c

[[Page 36944]]

 
                                                                        3. Record the batch cycle daily average
                                                                         scrubber liquid/gas ratio as specified
                                                                         in Sec.  63.1326(e)(2).
                                                                        4. Report all batch cycle daily average
                                                                         scrubber liquid/gas ratios that are
                                                                         below the minimum value established in
                                                                         the NCS or operating permit and all
                                                                         instances when monitoring data are not
                                                                         collected--PR.d e
Absorber f............................  a. Exit temperature of the      1. Continuous records as specified in
                                         absorbing liquid, and.          Sec.  63.1326(e)(1).b
                                                                        2. Record and report the average exit
                                                                         temperature of the absorbing liquid
                                                                         measured during the performance test--
                                                                         NCS.c
                                                                        3. Record the batch cycle daily average
                                                                         exit temperature of the absorbing
                                                                         liquid as specified in Sec.
                                                                         63.1326(e)(2) for each batchcycle.
                                                                        4. Report all the batch cycle daily
                                                                         average exit temperatures of the
                                                                         absorbing liquid that are above the
                                                                         maximum operating value established in
                                                                         the NCS or operating permit and all
                                                                         instances when monitoring data are not
                                                                         collected--PR.d e
                                        b. Exit specific gravity for    1. Continuous records as specified in
                                         the absorbing liquid.           Sec.  63.1326(e)(1).b
                                                                        2. Record and report the average exit
                                                                         specific gravity measured during the
                                                                         performance test--NCS.c
                                                                        3. Record the batch cycle daily average
                                                                         exit specific gravity as specified in
                                                                         Sec.  63.1326(e)(2).
                                                                        4. Report all batch cycle daily average
                                                                         exit specific gravity values that are
                                                                         above the maximum operating value
                                                                         established in the NCS or operating
                                                                         permit and all instances when
                                                                         monitoring data are not collected--PR.d
                                                                         e
Condenser f...........................  Exit (product side)             1. Continuous records as specified in
                                         temperature.                    Sec.  63.1326(e)(1).b
                                                                        2. Record and report the average exit
                                                                         temperature measured during the
                                                                         performance test--NCS.c
                                                                        3. Record the batch cycle daily average
                                                                         exit temperature as specified in Sec.
                                                                         63.1326(e)(2).
                                                                        4. Report all batch cycle daily average
                                                                         exit temperatures that are above the
                                                                         maximum operating value established in
                                                                         the NCS or operating permit and all
                                                                         instances when monitoring data are not
                                                                         collected--PR.d e
Carbon Adsorber f.....................  a. Total regeneration steam     1. Record the total regeneration steam
                                         flow or nitrogen flow, or       flow or nitrogen flow, or pressure for
                                         pressure (gauge or absolute)    each carbon bed regeneration cycle.
                                         during carbon bed              2. Record and report the total
                                         regeneration cycle(s), and.     regeneration steam flow or nitrogen
                                                                         flow,or pressure during carbon bed
                                                                         regeneration cycle measured during the
                                                                         performance test--NCS.c
                                                                        3. Report all carbon bed regeneration
                                                                         cycles when the total regeneration
                                                                         steam flow or nitrogen flow, or
                                                                         pressure is above the maximum value
                                                                         established in the NCS or operating
                                                                         permit--PR.d e
                                        b. Temperature of the carbon    1. Record the temperature of the carbon
                                         bed after regeneration and      bed after each regeneration and within
                                         within 15 minutes of            15 minutes of completing any cooling
                                         completing any cooling          cycle(s).
                                         cycle(s).
                                                                        2. Record and report the temperature of
                                                                         the carbon bed after each regeneration
                                                                         and within 15 minutes of completing any
                                                                         cooling cycle(s) measured during the
                                                                         performance test--NCS.c
                                                                        3. Report all carbon bed regeneration
                                                                         cycles when the temperature of the
                                                                         carbon bed after regeneration, or
                                                                         within 15 minutes of completing any
                                                                         cooling cycle(s), is above the maximum
                                                                         value established in the NCS or
                                                                         operating permit--PR.d e
All control devices...................  a. Diversion to the atmosphere  1. Hourly records of whether the flow
                                         from the control device or.     indicator was operating during batch
                                                                         emission episodes, or portions thereof,
                                                                         selected for control and whether a
                                                                         diversion was detected at any time
                                                                         during said periods as specified in
                                                                         Sec.  63.1326(e)(3).
                                                                        2. Record and report the times of all
                                                                         periods during batch emission episodes,
                                                                         or portions thereof, selected for
                                                                         control when emissions are diverted
                                                                         through a bypass line or the flow
                                                                         indicator is not operating--PR.d
                                        b. Monthly inspection of        1. Records that monthly inspections were
                                         sealed valves..                 performed as specified in Sec.
                                                                         63.1326(e)(4)(i).

[[Page 36945]]

 
                                                                        2. Record and report all monthly
                                                                         inspections that show the valves are in
                                                                         the diverting position or that a seal
                                                                         has been broken--PR.d
Absorber, condenser, and carbon         Concentration level or reading  1. Continuous records as specified in
 Adsorber (as an alternative to the      indicated by an organic         Sec.  63.1326(e)(1).b
 requirements previously presented in    monitoring device at the       2. Record and report the average batch
 this table).                            outlet of the control device.   vent concentration level or reading
                                                                         measured during the performance test--
                                                                         NCS.c
                                                                        3. Record the batch cycle daily average
                                                                         concentration level or reading as
                                                                         specified Sec.  63.1326(e)(2).
                                                                        4. Report all batch cycle daily average
                                                                         concentration levels or readings that
                                                                         are above the maximum value established
                                                                         in the NCS or operating permit and all
                                                                         instances when monitoring data are not
                                                                         collected--PR.d e
----------------------------------------------------------------------------------------------------------------
a Monitor may be installed in the firebox or in the ductwork immediately downstream of the firebox before any
  substantial heat exchange is encountered.
b ``Continuous records'' is defined in Sec.  63.111.
c NCS = Notification of Compliance Status described in Sec.  63.1335(e)(5).
d PR = Periodic Reports described in Sec.  63.1335(e)(6).
e The periodic reports shall include the duration of periods when monitoring data are not collected as specified
  in Sec.  63.1335(e)(6)(iii)(C).
f Alternatively, these devices may comply with the organic monitoring device provisions listed at the end of
  this table.

* * * * * * *

                    Table 9 of Subpart JJJ of Part 63
               [Routine reports required by this subpart]
------------------------------------------------------------------------
                                 Description of
          Reference                  report               Due date
------------------------------------------------------------------------
Sec.  63.1335(b) and subpart  Refer to Table 1 and  Refer to subpart A.
 A.                            subpart A.
Sec.  63.1335(e)(3).........  Precompliance Report  Existing affected
                               \a\.                  sources--December
                                                     19, 2000. New
                                                     affected sources--
                                                     with application
                                                     for approval of
                                                     construction or
                                                     reconstruction.
Sec.  63.1335(e)(4).........  Emissions Averaging   September 19, 2000.
                               Plan.
Sec.  63.1335(e)(4)(iv).....  Updates to Emissions  120 days prior to
                               Averaging Plan.       making the change
                                                     necessitating the
                                                     update.
Sec.  63.1335(e)(5).........  Notification of       Within 150 days
                               Compliance Status     after the
                               \b\.                  compliance date.
Sec.  63.1335(e)(6).........  Periodic Reports....  Semiannually, no
                                                     later than 60 days
                                                     after the end of
                                                     each 6-month
                                                     period. See Sec.
                                                     63.1335(e)(6)(i)
                                                     for the due date
                                                     for the first
                                                     report.
Sec.  63.1335(e)(6)(xi).....  Quarterly reports     No later than 60
                               for Emissions         days after the end
                               Averaging.            of each quarter.
                                                     First report is due
                                                     with the
                                                     Notification of
                                                     Compliance Status.
Sec.  63.1335(e)(6)(xii)....  Quarterly reports     No later than 60
                               upon request of the   days after the end
                               Administrator.        of each quarter.
Sec.  63.1335(e)(7)(i)......  Storage Vessels       At least 30 days
                               Notification of       prior to the
                               Inspection.           refilling of each
                                                     storage vessel or
                                                     the inspection of
                                                     each storage
                                                     vessel.
Sec.  63.1335(e)(7)(ii).....  Requests for          Initial submittal is
                               Approval of a         due with the
                               Nominal Control       Emissions Averaging
                               Efficiency for Use    Plan specified in
                               in Emissions          Sec.  63.1335(e)(4)
                               Averaging.            (ii); later
                                                     submittals are made
                                                     at the discretion
                                                     of the owner or
                                                     operator as
                                                     specified in Sec.
                                                     63.1335(e)(7)(ii)
                                                     (B).
Sec.  63.1335(e)(7)(iii)....  Notification of       1. For notification
                               Change in the         under Sec.
                               Primary Product.      63.1310(f)(3)(ii)--
                                                     notification
                                                     submittal date at
                                                     the discretion of
                                                     the owner or
                                                     operator.\c\
                                                    2. For notification
                                                     under Sec.
                                                     63.1310(f)(4)(ii)--
                                                     within 6 months of
                                                     making the
                                                     determination.
------------------------------------------------------------------------
\a\ There may be two versions of this report due at different times; one
  for equipment subject to Sec.  63.1331 and one for other emission
  points subject to this subpart.
\b\ There will be two versions of this report due at different times;
  one for equipment subject to Sec.  63.1331 and one for other emission
  points subject to this subpart.
\c\ Note that the TPPU remains subject to this subpart until the
  notification under Sec.  63.1310(f)(3)(i) is made.


[[Page 36946]]

[FR Doc. 01-17333 Filed 7-13-01; 8:45 am]
BILLING CODE 6560-01-U