[Federal Register Volume 66, Number 129 (Thursday, July 5, 2001)]
[Notices]
[Pages 35503-35504]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 01-16730]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

National Highway Traffic Safety Administration

[Docket No. NHTSA-2001-9848]


Notice of Receipt of Petition for Decision that Nonconforming 
1997 Chevrolet Cavalier Passenger Cars Are Eligible for Importation

AGENCY: National Highway Traffic Safety Administration, DOT.

ACTION: Notice of receipt of petition for decision that nonconforming 
1997 Chevrolet Cavalier passenger cars are eligible for importation.

-----------------------------------------------------------------------

SUMMARY: This document announces receipt by the National Highway 
Traffic Safety Administration (NHTSA) of a petition for a decision that 
the 1997 Chevrolet Cavalier that was not originally manufactured to 
comply with

[[Page 35504]]

all applicable Federal motor vehicle safety standards is eligible for 
importation into the United States because (1) it is substantially 
similar to a vehicle that was originally manufactured for importation 
into and sale in the United States and that was certified by its 
manufacturer as complying with the safety standards, and (2) it is 
capable of being readily altered to conform to the standards.

DATES: The closing date for comments on the petition is August 6, 2001.

ADDRESSES: Comments should refer to the docket number and notice 
number, and be submitted to: Docket Management, Room PL-401, 400 
Seventh St., SW., Washington, DC 20590. [Docket hours are from 9 am to 
5 pm]

FOR FURTHER INFORMATION CONTACT: George Entwistle, Office of Vehicle 
Safety Compliance, NHTSA (202-366-5306).

SUPPLEMENTARY INFORMATION:

Background

    Under 49 U.S.C. 30141(a)(1)(A), a motor vehicle that was not 
originally manufactured to conform to all applicable Federal motor 
vehicle safety standards shall be refused admission into the United 
States unless NHTSA has decided that the motor vehicle is substantially 
similar to a motor vehicle originally manufactured for importation into 
and sale in the United States, certified under 49 U.S.C. 30115, and of 
the same model year as the model of the motor vehicle to be compared, 
and is capable of being readily altered to conform to all applicable 
Federal motor vehicle safety standards.
    Petitions for eligibility decisions may be submitted by either 
manufacturers or importers who have registered with NHTSA pursuant to 
49 CFR part 592. As specified in 49 CFR 593.7, NHTSA publishes notice 
in the Federal Register of each petition that it receives, and affords 
interested persons an opportunity to comment on the petition. At the 
close of the comment period, NHTSA decides, on the basis of the 
petition and any comments that it has received, whether the vehicle is 
eligible for importation. The agency then publishes this decision in 
the Federal Register.
    Bayway Auto, Inc. of Elizabeth, New Jersey (``BWA'') (Registered 
Importer 98-166) has petitioned NHTSA to decide whether 1997 Chevrolet 
Cavalier passenger cars, originally manufactured for sale in the 
Middle-East, are eligible for importation into the United States. The 
vehicle which BWA believes is substantially similar is the 1997 
Chevrolet Cavalier that was manufactured for importation into, and sale 
in, the United States and certified by its manufacturer, General 
Motors, as conforming to all applicable Federal motor vehicle safety 
standards.
    The petitioner claims that it carefully compared the non-U.S. 
certified 1997 Chevrolet Cavalier passenger car to its U.S. certified 
counterpart, and found the two vehicles to be substantially similar 
with respect to compliance with most Federal motor vehicle safety 
standards.
    BWA submitted information with its petition intended to demonstrate 
that the non-U.S. certified 1997 Chevrolet Cavalier, as originally 
manufactured, conforms to many Federal motor vehicle safety standards 
in the same manner as its U.S. certified counterpart, or is capable of 
being readily altered to conform to those standards.
    Specifically, the petitioner claims that the non-U.S. certified 
1997 Chevrolet Cavalier is identical to its U.S. certified counterpart 
with respect to compliance with Standard Nos. 102 Transmission Shift 
Lever Sequence * * *, 103 Defrosting and Defogging Systems, 104 
Windshield Wiping and Washing Systems, 105 Hydraulic Brake Systems, 106 
Brake Hoses, 108 Lamps, Reflective Devices and Associated Equipment, 
109 New Pneumatic Tires, 110 Tire Selection and Rims, 113 Hood Latch 
Systems, 116 Brake Fluid, 118 Power Window Systems, 124 Accelerator 
Control Systems, 201 Occupant Protection in Interior Impact, 202 Head 
Restraints, 204 Steering Control Rearward Displacement, 205 Glazing 
Materials, 206 Door Locks and Door Retention Components, 207 Seating 
Systems, 209 Seat Belt Assemblies, 210 Seat Belt Assembly Anchorages, 
212 Windshield Retention, 214 Side Impact Protection, 216 Roof Crush 
Resistance, 219 Windshield Zone Intrusion, and 302 Flammability of 
Interior Materials.
    The petitioner also states that a vehicle identification number 
plate affixed to the vehicle meets the requirements of 49 CFR Part 565, 
that the anti-theft device meets the requirements of 49 CFR Part 541, 
and that the bumpers and bumper support structure satisfy the Bumper 
Standard found at 49 CFR Part 581.
    Petitioner also contends that the vehicle is capable of being 
readily altered to meet the following standards, in the manner 
indicated:
    Standard No. 101 Controls and Displays: (a) Substitution of a lens 
marked ``Brake'' for a lens with a noncomplying symbol on the brake 
failure indicator lamp; (b) installation of a seat belt warning lamp 
that displays the appropriate symbol; (c) replacement of the 
speedometer/odometer assembly unit with the U.S.-model component.
    Standard No. 111 Rearview Mirror: replacement of the passenger side 
rearview mirror with a U.S.-model component.
    Standard No. 114 Theft Protection: installation of a warning buzzer 
microswitch in the steering lock assembly and a warning buzzer.
    Standard No. 208 Occupant Crash Protection: (a) Installation of a 
U.S.-model seat belt in the driver's seating position or a belt webbing 
actuated microswitch inside the driver's seat belt retractor; (b) 
installation of an ignition switch actuated seat belt warning lamp and 
buzzer; (c) replacement of the driver's and passenger's side air bags 
and knee bolsters with U.S.-model components if the vehicle is not 
already so equipped. The petitioner states that the vehicles are 
equipped with combination lap and shoulder restraints which adjust by 
means of an automatic retractor and release by means of a single push 
button in both front designated seating positions, with combination lap 
and shoulder restraints which release by means of a single push button 
in both rear outboard designated seating positions, and with a lap belt 
in the rear center designated seating position.
    Standard No. 301 Fuel System Integrity: installation of a rollover 
valve in the fuel tank vent line.
    Interested persons are invited to submit comments on the petition 
described above. Comments should refer to the docket number and be 
submitted to: Docket Section, National Highway Traffic Safety 
Administration, Room 5109, 400 Seventh Street, SW., Washington, DC 
20590. It is requested but not required that 10 copies be submitted.
    All comments received before the close of business on the closing 
date indicated above will be considered, and will be available for 
examination in the docket at the above address both before and after 
that date. To the extent possible, comments filed after the closing 
date will also be considered. Notice of final action on the petition 
will be published in the Federal Register pursuant to the authority 
indicated below.

    Authority: 49 U.S.C. 30141(a)(1)(A) and (b)(1); 49 CFR 593.8; 
delegations of authority at 49 CFR 1.50 and 501.8.

    Issued on: June 28, 2001.
Marilynne Jacobs,
Director Office of Vehicle Safety Compliance.
[FR Doc. 01-16730 Filed 7-3-01; 8:45 am]
BILLING CODE 4910-59-P