[Federal Register Volume 66, Number 27 (Thursday, February 8, 2001)]
[Corrections]
[Pages 9635-9636]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: C0-24472]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Parts 413, 415, and 417

[Docket No. FAA-2000-7953; Notice No. 00-10]
RIN 2120-AG37


Licensing and Safety Requirements for Launch

Correction

    In proposed rule document 00-24472 beginning on page 63922 in the 
issue of Wednesday, October 25, 2000, make the following corrections:
    1. On page 63922, in the first column, the docket number is 
corrected to read as set forth above.


Sec. 417.233  [Corrected]

    2. On page 64022, in the second column, in Sec. 417.233(c)(5)(ii), 
in the fourth line, after ``the'' add ``EFG''.

Appendix A to 417 [Corrected]

    3. On page 64043, in the second column, in paragraph (ii), in the 
fifth line, ``1 x 100@5'' should read ``1 x 
10@5''.
    4. On page 64044, in the second column, in paragraph (7), in the 
eighth line, ``(i.e. log10)Pc'' should read 
``(i.e. log10(Pc'').

Appendix B to Part 417 [Corrected]

    5. On page 64051, in the first column, in the value description of 
y, ``diviation'' should read ``deviation ''.

Appendix C to Part 417 [Corrected]

    6. On page 64058, table C417-1 is corrected to read as set forth 
below:

Table C417-1, Illustrative Simulation Runs Required to Determine Drag Impact Point Dispersions for a Three Stage
                                                 Launch Vehicle
----------------------------------------------------------------------------------------------------------------
                                                                          Dispersion being determined
     Trajectory simulation runs  Stage performance error      --------------------------------------------------
                          parameters                               Stage 1          Stage 2          Stage 3
----------------------------------------------------------------------------------------------------------------
Stage 1 errors...............................................           X \1\   ...............  ...............
Stage 1 errors, Stage 2 nominal..............................  ...............               X   ...............
Stage 1 nominal, Stage 2 errors..............................  ...............               X   ...............
Stage 1 errors, Stage 2 nominal, Stage 3 nominal.............  ...............  ...............               X
Stage 1 nominal, Stage 2 errors, Stage 3 nominal.............  ...............  ...............               X
Stage 1 nominal, Stage 2 nominal, Stage 3 errors.............  ...............  ...............              X
----------------------------------------------------------------------------------------------------------------
\1\ An X in a given stage column indicates that the noted simulation runs are required to determine the
  dispersion for that stage.


[[Page 9636]]

Appendix E to Part 417 [Corrected]

    7. On page 64091, in table E417.25-3, under the ``Quality'' 
heading, after each ``100'' entry, add a ``%'' sign.
    8. On page 64094, the second table heading, ``Table E417.25-75'' 
should read ``Table E417.25-7''.
    9. On page 64096, in table E417.27-2, for the entry ``Performance 
Verification'' remove the ``X'' in each column.
    10. On the same page, in the same table, for the entry ``Non-
Operating Environment Tests'' remove the ``X '' in each column.
    11. On page 64099, in table E417.27-5, for the entry ``High 
Temperature Storage'', remove the ``X'' in the column named ``1 
year\4\''.
    12. On page 64101, in table E417.29-2, for the entry ``Firing 
Test'', in the Reference column, ``E417.(g)'' should read 
``E417.29(g)''.
    13. On page 64104, in table E417.31-2, for the entry ``Non-
Operating Environment Tests and Operating Environment Tests'', remove 
the ``X'' in the third column.
    14. On the same page, in table E417.31-3, under the ``Quality'' 
heading, before each ``100%'' entry, remove the footnote reference 
``\1\''.
    15. On page 64105, in table E417.31-4, for the entry ``Low 
Temperature'', remove the ``5'' in the column named ``105 ''.
    16. On page 64107, in table E417.33-3, for the entry ``Component 
Examination'', remove the ``X'' in each column.
    17. On page 64109, in table E417-37-1, under the entry ``Shock'', 
add an ``X'' in the ``Quantity'' column.

[FR Doc. C0-24472 Filed 2-7-01; 8:45 am]
BILLING CODE 1505-01-D