[Federal Register Volume 65, Number 207 (Wednesday, October 25, 2000)]
[Notices]
[Pages 63913-63914]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 00-27316]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

National Highway Traffic Safety Administration

[Docket No. NHTSA-2000-8133]


Panoz Auto Development Company; Application for Temporary 
Exemption From Federal Motor Vehicle Safety Standard No. 208

    Panoz Auto Development Company of Hoschton, Georgia, has applied 
for a temporary exemption from paragraph S4.1.4 of Federal Motor 
Vehicle Safety Standard No. 208 Occupant Crash Protection. The basis of 
the application is that compliance will cause substantial economic 
hardship to a manufacturer that has tried to comply with the standard 
in good faith.
    This notice of receipt of an application for renewal is published 
in accordance with the requirements of 49 U.S.C. 30113(b)(2) and does 
not represent any judgment of the agency on the merits of the 
application.
    Panoz received NHTSA Exemption No. 93-5 from S4.1.4 of Standard No. 
208, an exemption for two years which was initially scheduled to expire 
August 1, 1995 (58 FR 43007). It applied for, and received, two two-
year renewals of this exemption (61 FR 2866; 63 FR 16856), the last of 
which expired March 1, 2000. Panoz now seeks a new exemption from 
S4.1.4 on hardship grounds, that would expire March 31, 2003. This 
exemption would apply to the Roadster but not to the company's other 
product, Esperante, which has been designed during the term of the last 
exemption to comply with S4.1.4.
    Panoz's original exemption was granted pursuant to the 
representation that its Roadster would be equipped with a Ford-supplied 
driver and passenger airbag system, and would comply with Standard No. 
208 by April 5, 1995, after estimated expenditures of $472,000. As of 
the time of its application, April 1993, the company had expended 750 
man hours and $15,000 on the project.
    According to its 1995 application for renewal,

Panoz has continued the process of researching and developing the 
installation of a driver and passenger side airbag system on the 
Roadster since the original exemption petition was submitted to 
NHTSA on

[[Page 63914]]

April 5, 1993. To date, an estimated 1680 man-hours and 
approximately $50,400 have been spent on this project.

    At that time, Panoz used a 5.0L Ford Mustang GT engine and five 
speed manual transmission in its car. Because ``the 1995 model year and 
associated emission components were revised by Ford,'' this caused

a delay in the implementation of the airbag system on the Roadster 
due to further research and development time requirements and 
expenditure of additional monies to evaluate the effects of these 
changes on the airbag adaptation program.

    Shortly before filing its application for first renewal in 1995, 
Panoz learned that Ford was replacing the 5.0L engine and emission 
control system on the 1996 Mustang and other passenger cars with a 
modular 4.6L engine and associated emission components. The 1995 system 
did not meet 1996 On-Board Diagnostic emission control requirements, 
and Panoz was faced with using the 1996 engine and emission control 
system as a substitute. The majority of the money and man hours at that 
time had been spent on adapting an airbag system to the 5.0L engine 
car, and the applicant had to concentrate on adapting it to a 4.6L 
engine car. Panoz listed eight types of modifications and testing 
necessary for compliance that would cost it $337,000 if compliance were 
required at the end of a one-year period. It asked for and received a 
two-year renewal of its exemption.
    However, between 1995 and 1997, Panoz found integration of the 4.6L 
engine into its existing chassis more difficult than anticipated, 
primarily because the 4.6L was 10 inches wider than the engine it 
replaced. This required a total redesign of the chassis, requiring 
expenditure of ``a significant amount of resources.'' Simultaneously, 
Panoz designed the vehicle to allow for the integration of the Ford 
Mustang driver-side and passenger-side airbag systems. Panoz described 
these steps in some detail and estimates that between May 1995 and 
August 1997 it spent 2200 man-hours and $66,000 on these efforts. In 
the same time period, it spent $47,000 in static and dynamic crash 
testing of a 4.6L car related to airbag system development. Panoz 
concluded by describing the additional modifications and testing 
required to adapt the Ford system to its car. These costs totaled 
$358,000. In 1997, the company argued that a two-year renewal of its 
exemption would provide time to generate sufficient income 
(approximately $15,000 a month through sales of vehicles and private 
funding) to fund the modifications and testing. After August 1997, 
Panoz spent an additional 1779 man hours and $87,375 in airbag 
development for the Roadster, a large portion of which was to adapt the 
1997-98 Ford Mustang mechanical system. In September 1998, NHTSA issued 
its NPRM on advanced airbags which would have required Panoz to begin 
the phase-in of the new system as of September 1, 2002. Panoz decided 
that the mechanical airbag system it was developing could not comply 
with the proposed advanced system. It also lacked the resources to 
develop two systems simultaneously, so it turned its development 
efforts towards the advanced system, which will be in its new model, 
Esperante. In November 1999, NHTSA issued a Supplemental NPRM under 
which implementation of the advanced airbag rule would be delayed for 
small manufacturers until September 1, 2005 (subsequently adopted in 
the final rule of May 2000). This resulted in Panoz's resumption of 
efforts to adapt the Ford Mustang airbag system to its Roadster. 
However, with its 1999 models, Ford had replaced the mechanical airbag 
system with an electronic one, ``which dictated that Panoz would have 
to conduct further crash testing in order to properly calibrate the 
[Restraint Control Module] for application on the AIV Roadster.'' Panoz 
intends to have the electronic system adapted by the end of the 
exemption it has requested. The foregoing is a summary of Panoz's 
compliance efforts which are set forth in detail in its application.
    In sum, Panoz has been exempted from compliance with the airbag 
requirements for all passenger cars that it manufactured between August 
1, 1993, and March 1, 2000, approximately 6\1/2\ years. These total 178 
units.
    At the time of its original petition, Panoz's cumulative net losses 
since incorporation in 1989 were $1,265,176. It lost an additional 
$249,478 in 1993, $169,713 in 1994, $721,282 in 1995, and $1,349,241 in 
1996. Its losses continued in 1997, 1998, and 1999, respectively 
$3,253,111, $4,264,689, and $2,996,903. Thus, Panoz's losses for the 
years that the exemption was in effect, 1993-99, total $13,004,417.
    The applicant reiterated its original arguments that an exemption 
would be in the public interest and consistent with the objectives of 
traffic safety. Specifically, The Roadster is built in the United 
States and uses 100 percent U.S. components, bought from Ford and 
approximately 95 other companies (``at least 250 employees'' of which 
``remain involved in the Panoz project''). Panoz provides employment 
for 47 full time and three part time employees. The company now has 33 
U.S. dealers. The Roadster is said to provide the public with a classic 
alternative to current production vehicles. It is the only vehicle that 
incorporates ``molded aluminum body panels for the entire car,'' a 
process which continues to be evaluated by other manufacturers and 
which ``results in the reduction of overall vehicle weight, improved 
fuel efficiency, shortened tooling lead times, and increased body 
strength.'' With the exception of S4.1.4 of Standard No. 208, the 
Roadster meets all other Federal motor vehicle safety standards.
    Interested persons are invited to submit comments on the 
application described above. Comments should refer to the docket number 
and the notice number, and be submitted to: Docket Management, 
Department of Transportation, room PL-401, 400 Seventh Street SW, 
Washington, DC 20590. It is requested but not required that 10 copies 
be submitted.
    All comments received before the close of business on the comment 
closing date indicated below will be considered, and will be available 
for examination in the docket at the above address both before and 
after that date. To the extent possible, comments filed after the 
closing date will also be considered. Notice of final action on the 
application will be published in the Federal Register pursuant to the 
authority indicated below. Comment closing date: November 24, 2000.

    Authority: (49 U.S.C. 30113; delegations of authority at 49 CFR 
1.50. and 501.8).

    Issued on October 19, 2000.
Stephen R. Kratzke,
Associate Administrator for Safety Performance Standards.
[FR Doc. 00-27316 Filed 10-24-00; 8:45 am]
BILLING CODE 4910-59-P