[Federal Register Volume 65, Number 69 (Monday, April 10, 2000)]
[Notices]
[Pages 19040-19041]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 00-8742]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

National Highway Traffic Safety Administration

[Docket No. NHTSA-2000-7002]


Notice of Receipt of Petition for Decision that Nonconforming 
1976-1985 Rolls Royce Corniche Passenger Cars Are Eligible for 
Importation

AGENCY: National Highway Traffic Safety Administration, DOT.

ACTION: Notice of receipt of petition for decision that nonconforming 
1976-1985 Rolls Royce Corniche passenger cars are eligible for 
importation.

-----------------------------------------------------------------------

SUMMARY: This notice announces receipt by the National Highway Traffic 
Safety Administration (NHTSA) of a petition for a decision that 1976-
1985 Rolls Royce Corniche passenger cars that were not originally 
manufactured to comply with all applicable Federal motor vehicle safety 
standards are eligible for importation into the United States because 
(1) they are substantially similar to vehicles that were originally 
manufactured for importation into and sale in the United States and 
that were certified by their manufacturer as complying with the safety 
standards, and (2) they are capable of being readily altered to conform 
to the standards.

DATES: The closing date for comments on the petition is May 10, 2000.

ADDRESSES: Comments should refer to the docket number and notice 
number, and be submitted to: Docket Management, Room PL-401, 400 
Seventh St., SW, Washington, DC 20590. [Docket hours are from 9 am to 5 
pm].

FOR FURTHER INFORMATION CONTACT: George Entwistle, Office of Vehicle 
Safety Compliance, NHTSA (202-366-5306).

SUPPLEMENTARY INFORMATION:   

Background

    Under 49 U.S.C. 30141(a)(1)(A), a motor vehicle that was not 
originally manufactured to conform to all applicable Federal motor 
vehicle safety standards shall be refused admission into the United 
States unless NHTSA has decided that the motor vehicle is substantially 
similar to a motor vehicle originally manufactured for importation into 
and sale in the United States, certified under 49 U.S.C. 30115, and of 
the same model year as the model of the motor vehicle to be compared, 
and is capable of being readily altered to conform to all applicable 
Federal motor vehicle safety standards.

[[Page 19041]]

    Petitions for eligibility decisions may be submitted by either 
manufacturers or importers who have registered with NHTSA pursuant to 
49 CFR Part 592. As specified in 49 CFR 593.7, NHTSA publishes notice 
in the Federal Register of each petition that it receives, and affords 
interested persons an opportunity to comment on the petition. At the 
close of the comment period, NHTSA decides, on the basis of the 
petition and any comments that it has received, whether the vehicle is 
eligible for importation. The agency then publishes this decision in 
the Federal Register.
    Champagne Imports of Lansdale, Pennsylvania (``Champagne'') 
(Registered Importer 90-009) has petitioned NHTSA to decide whether 
1976-1985 Rolls Royce Corniche passenger cars are eligible for 
importation into the United States. The vehicles which Champagne 
believes are substantially similar are 1976-1985 Rolls Royce Corniche 
passenger cars that were manufactured for importation into, and sale 
in, the United States and certified by their manufacturer as conforming 
to all applicable Federal motor vehicle safety standards.
    The petitioner claims that it carefully compared non-U.S. certified 
1976-1985 Rolls Royce Corniche passenger cars to their U.S. certified 
counterparts, and found the vehicles to be substantially similar with 
respect to compliance with most Federal motor vehicle safety standards.
    Champagne submitted information with its petition intended to 
demonstrate that non-U.S. certified 1976-1985 Rolls Royce Corniche 
passenger cars, as originally manufactured, conform to many Federal 
motor vehicle safety standards in the same manner as their U.S. 
certified counterparts, or are capable of being readily altered to 
conform to those standards.
    Specifically, the petitioner claims that non-U.S. certified 1976-
1985 Rolls Royce Corniche passenger cars are identical to their U.S. 
certified counterparts with respect to compliance with Standards Nos. 
102 Transmission Shift Lever Sequence . . . ., 103 Defrosting and 
Defogging Systems, 104 Windshield Wiping and Washing Systems, 105 Brake 
Systems, 106 Brake Hoses, 109 New Pneumatic Tires, 113 Hood Latch 
Systems, 116 Brake Fluid, 124 Accelerator Control Systems, 201 Occupant 
Protection in Interior Impact, 202 Head Restraints, 203 Impact 
Protection for the Driver from the Steering Control System, 204 
Steering Control Rearward Displacement, 205 Glazing Materials, 206 Door 
Locks and Door Retention Components, 207 Seating Systems, 209 Seat Belt 
Assemblies, 210 Seat Belt Assembly Anchorages, 212 Windshield 
Retention, 216 Roof Crush Resistance, 219 Windshield Zone Intrusion, 
and 302 Flammability of Interior Materials.
    Petitioner also contends that the vehicles are capable of being 
readily altered to meet the following standards, in the manner 
indicated:
    Standard No. 101 Controls and Displays: (a) substitution of a lens 
marked ``Brake'' for a lens with a noncomplying symbol on the brake 
failure indicator lamp; (b) installation of a seat belt warning lamp 
that displays the appropriate symbol; (c) recalibration of the 
speedometer/odometer from kilometers to miles per hour.
    Standard No. 108 Lamps, Reflective Devices and Associated 
Equipment: (a) installation of U.S.-model headlamp assemblies that 
incorporate headlamps with DOT markings; (b) installation of U.S.-model 
front and rear sidemarker/reflector assemblies; (c) installation of 
U.S.-model taillamp assemblies.
    Standard No. 110 Tire Selection and Rims: installation of a tire 
information placard.
    Standard No. 111 Rearview Mirror: replacement of the convex 
passenger side rearview mirror.
    Standard No. 114 Theft Protection: installation of a warning buzzer 
microswitch in the steering lock assembly and a warning buzzer.
    Standard No. 118 Power Window Systems: rewiring of the power window 
system so that the window transport is inoperative when the ignition is 
switched off.
    Standard No. 208 Occupant Crash Protection: (a) installation of a 
U.S.-model seat belt in the driver's position, or a belt webbing-
actuated microswitch inside the driver's seat belt retractor; (b) 
installation of an ignition switch-actuated seat belt warning lamp and 
buzzer. The petitioner states that the vehicles are equipped with 
combination lap and shoulder restraints that adjust by means of an 
automatic retractor and release by means of a single push button at 
both front designated seating positions, and with lap belts at both 
rear outboard and rear center designated seating positions.
    Standard No. 214 Side Impact Protection: installation of 
reinforcing beams.
    Standard No. 301 Fuel System Integrity: installation of a rollover 
valve in the fuel tank vent line between the fuel tank and the 
evaporative emissions collection canister.
    Additionally, the petitioner states that the bumpers on the non-
U.S. certified 1976-1985 Rolls Royce Corniche passenger cars must be 
reinforced or U.S.-model bumper components must be installed to comply 
with the Bumper Standard found in 49 CFR Part 581.
    The petitioner also states that a vehicle identification number 
plate must be affixed to the vehicle to meet the requirements of 49 CFR 
Part 565.
    Interested persons are invited to submit comments on the petition 
described above. Comments should refer to the docket number and be 
submitted to: Docket Section, National Highway Traffic Safety 
Administration, Room 5109, 400 Seventh Street, S.W., Washington, DC 
20590. It is requested but not required that 10 copies be submitted.
    All comments received before the close of business on the closing 
date indicated above will be considered, and will be available for 
examination in the docket at the above address both before and after 
that date. To the extent possible, comments filed after the closing 
date will also be considered. Notice of final action on the petition 
will be published in the Federal Register pursuant to the authority 
indicated below.

    Authority: 49 U.S.C. 30141(a)(1)(A) and (b)(1); 49 CFR 593.8; 
delegations of authority at 49 CFR 1.50 and 501.8.

    Issued on: April 5, 2000.
Marilynne Jacobs,
Director, Office of Vehicle Safety Compliance.
[FR Doc. 00-8742 Filed 4-7-00; 8:45 am]
BILLING CODE 4910-59-P