[Federal Register Volume 64, Number 230 (Wednesday, December 1, 1999)]
[Rules and Regulations]
[Pages 67170-67187]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 99-28611]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Coast Guard
33 CFR Parts 127, 154, 155, 159, 164, and 183; and
46 CFR Parts 28, 30, 32, 34, 35, 38, 39, 54, 56, 58, 61, 63, 76,
77, 78, 92, 95, 96, 97, 105, 108, 109, 110, 111, 114, 119, 125,
151, 153, 154, 160, 161, 162, 163, 164, 170, 174, 175, 182, 190,
193, 195, and 199
[USCG-1999-5151]
RIN 2115-AF80
Update of Standards From the American Society for Testing and
Materials (ASTM)
AGENCY: Coast Guard, DOT.
ACTION: Direct final rule.
-----------------------------------------------------------------------
SUMMARY: By this direct final rule, the Coast Guard amends Titles 33
and 46, Code of Federal Regulations, to render current the standards
incorporated by reference from the American Society for Testing and
Materials (ASTM). Some of the standards incorporated were over 30 years
out of date. This rule incorporates the most recent editions of the
standards to ensure the use by regulated industry of the latest
technology.
DATES: This direct final rule is effective on February 29, 2000, unless
a written adverse comment, or written notice of intent to submit an
adverse comment, reaches the Docket Management Facility on or before
January 31, 2000. If you submit an adverse comment, or notice of intent
to submit an adverse comment, the Coast Guard will withdraw this rule
and publish a timely notice of withdrawal in the Federal Register. The
incorporation by reference of publications in this rule was approved by
the Director of the Federal Register on February 29, 2000.
ADDRESSES: To make sure your comments and related material are not
entered more than once in the docket, please submit them by only one of
the following means:
(1) By mail to the Docket Management Facility (USCG-1999-5151),
U.S. Department of Transportation, room PL-401, 400 Seventh Street SW.,
Washington, DC 20590-0001.
(2) By delivery to room PL-401 on the Plaza level of the Nassif
Building, 400 Seventh Street SW., Washington, DC, between 9 a.m. and 5
p.m., Monday through Friday, except Federal holidays. The telephone
number is 202-366-9329.
(3) By fax to the Docket Management Facility at 202-493-2251.
(4) Electronically through the Web Site for the Docket Management
System at http://dms.dot.gov.
[[Page 67171]]
The Docket Management Facility maintains the public docket for this
rulemaking. Comments and material received from the public, as well as
documents mentioned in this preamble as being available in the docket,
will become part of this docket and will be available for inspection or
copying at room PL-401 on the Plaza level of the Nassif Building, 400
Seventh Street SW., Washington, DC, between 9 a.m. and 5 p.m., Monday
through Friday, except Federal holidays. You may also find this docket
on the Internet at http://dms.dot.gov.
You may inspect the material incorporated by reference at room
1312, U.S. Coast Guard Headquarters, 2100 Second Street SW.,
Washington, DC 20593-0001, between 9 a.m. and 4:30 p.m., Monday through
Friday, except Federal holidays. The telephone number is 202-267-0257.
Copies of the material are available as indicated in the
``Incorporation by Reference'' section of this preamble.
FOR FURTHER INFORMATION CONTACT: For questions on this rule, call Ms.
Janet Walton, Office of Standards, Evaluation and Development (G-MSR),
U.S. Coast Guard, telephone 202-267-0257. For questions on viewing, or
submitting material to, the docket, call Dorothy Walker, Chief,
Dockets, Department of Transportation, telephone 202-366-9329.
SUPPLEMENTARY INFORMATION:
Request for Comments
The Coast Guard encourages you to participate in this rulemaking by
submitting comments and related material. If you do so, please include
your name and address, identify the docket number for this rulemaking
(USCG-1999-5151), indicate the specific section of this document to
which each comment applies, and give the reason for each comment. You
may submit your comments and material by mail, delivery, fax, or
electronic means to the Docket Management Facility at the address under
ADDRESSES; but please submit your comments and material by only one
means. If you submit them by mail or delivery, submit them in an
unbound format, no larger than 8\1/2\ by 11 inches, suitable for
copying and electronic filing. If you submit them by mail and would
like to know they reached the Facility, please enclose a stamped, self-
addressed postcard or envelope. We will consider all comments and
material received during the comment period. We may change this rule in
view of them.
Regulatory Information
The Coast Guard is publishing a direct final rule, the procedures
for which appear in 33 CFR 1.05-55, because it anticipates no adverse
comment. Unless, during the specified comment period, it receives
either a written adverse comment or written notice of intent to submit
one, this rule will become effective on February 29, 2000. In that
case, shortly before or after that date, the Coast Guard will publish a
document in the Federal Register stating that it received neither any
written adverse comment nor any written notice of intent to submit one
and confirming that this rule will or did become effective on February
29, 2000.
Nevertheless, if the Coast Guard receives either a written adverse
comment or written notice of intent to submit one, it will publish a
document in the Federal Register announcing withdrawal of all or part
of this rule. If an adverse comment or a notice of intent to submit one
applies to only part of this rule, and removal of that part is possible
without defeating the purpose of this rule, the Coast Guard may adopt
as final those parts of this rule on which it received no such comment
or notice. In either case it will withdraw any part of this rule that
was the subject of any such comment or notice. If it decides to proceed
with a rulemaking following receipt of any such comment or notice, it
will publish a separate Notice of Proposed Rulemaking (NPRM) and
provide a new opportunity for comment.
A comment counts as ``adverse'' if it explains why this rule would
be inappropriate or would be ineffective or unacceptable without a
change, or challenges the premise or approach of the rule.
Background and Purpose
The Coast Guard uses standards established by other organizations,
such as ASTM, as a means of establishing technical requirements.
Incorporation by reference allows the Coast Guard to include these
technical standards in its rules without increasing the volume of the
Code of Federal Regulations (CFR). The Federal Register is the only
medium through which the Coast Guard and other agencies can incorporate
by reference. 1 CFR part 51 prescribes the methods and procedures for
incorporation by reference.
This rule changes most of the 170 standards from ASTM now
incorporated by reference in titles 33 and 46 of the CFR. Standards B
858, D 4268, F 1387, F 1548, and Adjunct F 1626 continue to call for
the most recent technology and have not yet been withdrawn or updated
by ASTM. ASTM typically updates each standard every 5 years.
ASTM has discontinued standards A 7, A 300, A 430, A 442, A 525, B
97, B 141, and D 1692 and replaced each with a different standard from
ASTM. The Coast Guard has eliminated standards F 808 and F 989 from its
rules without replacement since ASTM discontinued them, and the Coast
Guard has determined that no replacement is necessary. The Coast Guard
will incorporate the rest, which ASTM has updated. It will incorporate
these because, in addition to its desire for industry to use the most
recent technology, the older editions may be difficult for some parties
to find.
Discussion of Rule
This rule contains two kinds of updates of standards from ASTM: (1)
updates of those standards that bear the same numbers and same general
technical contents but that ASTM has brought into more recent year-
versions, and (2) updates of those that ASTM has discontinued and
replaced or combined with others. A brief description of the two kinds
follows:
(1) More Recent Year-Versions of Standards
ASTM has brought the standards listed below into more recent
versions. The later versions bear the same general technical contents
as the standards currently incorporated, but have been reviewed by ASTM
committees on a five-year schedule and brought into new ``year-
versions.'' For example, ASTM standard A 27-80 (1980 version of
standard A 27) is currently incorporated into the rules of the Coast
Guard. The newer version of this standard is A 27-95 (1995 version of
standard A 27).
In some cases, ASTM reviews the standards in its 5-year cycle and
re-certifies them unchanged. Such standards appear here with the years
of their re-certification in parentheses. For example, standard A 192-
91 (1996) is the 1991 version of standard A 192 re-certified in 1996
unchanged.
During the review of standards, changes occur--or not--by consensus
of the members of committees of ASTM. Since this process provides the
opportunity for members of industry, government, and academia to
participate, the Coast Guard considers the updated standards to have
been adequately reviewed and to be technically sound.
ASTM has brought the following standards into more recent year-
versions:
[[Page 67172]]
A 20, A 27, A 36, A 47, A 53, A 106, A 126, A 134, A 135, A 139, A
178, A 179, A 182, A 192, A 193, A 194, A 197, A 199, A 203, A 210, A
213, A 214, A 216, A 226, A 234, A 249, A 268, A 276, A 302, A 307, A
312, A 320, A 325, A 333, A 334, A 335, A 336, A 350, A 351, A 352, A
358, A 369, A 370, A 376, A 387, A 395, A 403, A 420, A 449, A 508, A
516, A 520, A 522, A 524, A 533, A 536, A 537, A 575, A 576, A 612, A
662, A 653, A 724, B 16, B 21, B 26, B 42, B 43, B 68, B 75, B 85, B
88, B 96, B 111, B 117, B 122, B 124, B 127, B 152, B 154, B 161, B
165, B 167, B 171, B 209, B 210, B 234, B 241, B 280, B 283, B 315, B
361, C 177, C 518, D 92, D 93, D 323, D 413, D 471, D 570, D 635, D
665, D 751, D 882, D 975, D 1004, D 1434, D 1435, D 1518, D 1621, D
1622, D 1785, D 2241, D 2464, D 2466, D 2467, D 2665, D 2777, D 2842, D
2863, D 4066, D 4986, E 11, E 23, E 84, E 119, E 208, E 648, E 662, F
631, F 682, F 715, F 722, F 1003, F 1006, F 1007, F 1014, F 1020, F
1120, F 1121, F 1122, F 1123, F 1139, F 1155, F 1172, F 1173, F 1196, F
1197, F 1199, F 1200, F 1201, F 1271, F 1273, F 1321, F 1323, F 1476, F
1546, and F 1548.
(2) Discontinued, Replaced, and Combined Standards
ASTM has completely discontinued some standards incorporated into
the rules of the Coast Guard for either a lack of need by industry or
the development of other, more modern standards. In some cases, ASTM
has replaced the discontinued standards with current ones. In others,
ASTM has discontinued standards with no replacements, and the Coast
Guard has either removed them from its rules or replaced them with
similar standards. In yet others, ASTM has combined two or more
standards to form one common one.
Each of the following eleven standards falls into one of these
three categories:
(1) ASTM A 7-65, ``Standard Specifications for Steel for Bridges
and Buildings.'' ASTM discontinued this standard in 1967 and replaced
it with A 36-97a, ``Standard Specification for Carbon Structural
Steel.'' The Coast Guard has determined that this replacement is
appropriate in its rules. The Coast Guard originally incorporated by
reference ASTM A 7 into 46 CFR 160.032-1, which governs materials used
for davits. It requires that structural steel made by the open-hearth
or electric-furnace process meet this standard.
(2) ASTM A 199-84, ``Specification for Seamless Cold-Drawn
Intermediate Alloy-Steel Heat-Exchanger and Condenser Tubes.'' ASTM
discontinued this standard in 1995 and replaced it with A 200,
``Specification for Seamless Intermediate Alloy-Steel Still Tubes for
Refinery Service, and A 213, Standard Specification for Seamless
Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-
Exchanger Tubes.'' The Coast Guard originally incorporated by reference
ASTM A 199 into 46 CFR Table 56.60-1(a) as an acceptable piping
standard for alloy-steel condenser tubes. Since ASTM no longer
promulgates ASTM A 199, the Coast Guard has removed it from its rules.
But the Coast Guard cannot substitute ASTM A 200 for it yet, because
too little time remained before this rule's going to press for the
Coast Guard to analyze the new standard. Nevertheless, the same rules
allow piping systems selected from the material specifications of the
Code of the American Society of Mechanical Engineers (ASME), Section I,
III, or VIII. And ASME may be adding A 200 to its own list of accepted
standards in the near future; this, even without reference to ASTM,
would allow its use. ASTM A 213, which is also a replacement for A 199,
already appears in 46 CFR Table 56.60-1(a) and therefore does not need
to be added to the rules.
(3) ASTM A 300, ``Standard Specification for Notch Toughness
Requirements for Normalized Steel Parts for Pressure Vessels.'' ASTM
discontinued this standard in 1995 with no replacement, but expanded
and incorporated it into A 20, ``Standard Specification for General
Requirements for Steel Plates for Pressure Vessels.'' This applies to
the testing of plate materials. The Coast Guard has determined that
ASTM A 20 will serve its purposes and by this rule incorporates it into
46 CFR 54.05-10. The Coast Guard edited its rules to direct the reader
to the sections of ASTM A 20 that will apply.
(4) ASTM A 430-84a, ``Standard Specification for Austenitic Steel,
Forged and Bored Pipe for High-Temperature Service.'' ASTM discontinued
this standard in 1995, and replaced it with A 312-95, ``Standard
Specification for Seamless and Welded Austenitic Stainless Steel
Pipes.'' The Coast Guard has determined that it should eliminate ASTM A
430 from 46 CFR subpart 56.01 and also from Table 56.60-1(A), which
lists standards acceptable for specific piping. ASTM A 312 already
appears in this subpart, and remains available for use regardless of
ASTM A 430.
(5) ASTM A 442, ``Standard Specification for Pressure Vessel
Plates, Carbon Steel, Improved Transition Properties.'' ASTM
discontinued this standard in 1991 with no formal (committee-balloted)
replacement. However, ASTM A 516, ``Standard Specification for Pressure
Vessel Plates, Carbon Steel, for Moderate and Lower Temperature
Service'' is the ASTM-recommended replacement. Both standards appear in
46 CFR 54.25-10, which concerns low-temperature operation of ferritic
steels. In that section, certain materials, if below specified
thicknesses, are exempt from the requirement for ``Charpy impact
tests.'' Material of Grade 55, called out by ASTM A 442, is one of
these. Since ASTM has discontinued ASTM A 442, the Coast Guard has
determined that it should delete it from this section. ASTM A 516
already appears there and therefore does not need to be added to the
rules.
(6) ASTM A 525, ``Standard Specification for General Requirements
for Steel Sheet, Zinc-Coated (Galvanized) by the Hot-Dip Process.''
ASTM discontinued this standard in 1994 with no replacement. ASTM
recommends using A 653, ``Standard Specification for Steel Sheet, Zinc-
Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the
Hot-Dip Process'' in its place. The Coast Guard has determined that it
should eliminate ASTM A 525 in 46 CFR 160.035-3(b), which specifies
plating requirements for steel oar-propelled lifeboats. The Coast Guard
has replaced ASTM A 525 with ASTM A 653.
(7) ASTM B 97, ``Standard Specification for Copper Silicon-Alloy
Plate, Sheet, Strip, and Rolled Bar for General Purposes.'' ASTM
discontinued this standard in 1982, and replaced it with B 96,
``Standard Specification for Copper Silicon Alloy Plate, Sheet, Strip
and Rolled Bar for General Purposes and Pressure Vessels.'' The Coast
Guard has determined that ASTM B 96 serves its purposes and can replace
ASTM B 97 where the latter appears: in rules for construction of fuel
tanks (46 CFR 58.50-5, 119.440, and 182.440). The Coast Guard has
modified regulatory text in each of these rules, so that alloys ``A and
B'' in ASTM B 97 give way to alloys C65100 and C65500 in B 96. (Alloy
``C,'' referred to in the rules, is no longer manufactured and does not
require an equivalent in B 96.)
(8) ASTM B 141-45, ``Standard Specifications for Electrodeposited
Coatings of Nickel and Chromium on Copper and Copper-base Alloys.''
ASTM discontinued this standard in 1967, and replaced it with B 456,
``Standard Specification for Electro-deposited Coatings of Copper Plus
Nickel Plus Chromium and Nickel Plus Chromium.'' The Coast Guard has
determined that
[[Page 67173]]
ASTM B 456 serves its purposes. ASTM B 141 originally governed
construction of searchlight reflectors, in 46 CFR 161.006-4. When the
Coast Guard incorporated the new standard, it also revised regulatory
text to accommodate the new standard, so that ``type K C'' in ASTM B
141 gives way to ``service condition SC 1'' in ASTM B 456.
(9) ASTM D 1692 and D 1692T, ``Rate of Burning [or] Extent and Time
of Burning of Cellular Plastics Using a Specimen Supported by a
Horizontal Screen.'' ASTM discontinued these standards in 1978 with no
formal (committee-balloted) replacement. ASTM D 4986-98, ``Test Method
for Horizontal Burning Characteristics of Cellular Polymeric
Materials'' will serve in their places. ASTM D 1692 is incorporated by
reference into 46 CFR subparts 32.57 and 151.15, and helps test the
fire-resistance of insulating-materials. This rule will incorporate
ASTM D 4986-98 into Sec. 38.01-3.
(10) ASTM F 989, ``Standard Test Methods for Spill Control Barrier
Tension Members.'' ASTM discontinued this standard in 1995 with no
replacement. This standard was originally incorporated in 33 CFR parts
154 (Appendix C) and 155 (Appendix B), which include requirements for
the testing of oil-response boom. The Coast Guard has determined that
it is appropriate to eliminate the standard from the text without
adding a replacement: The current regulatory text gives the reader the
option of using old ASTM F 989, ASTM F 715 (Standard Methods of Testing
Spill Control Barrier Membrane Materials), or any of several tests
approved by the Coast Guard; and the latter two options remain
available.
(11) ASTM F 808, ``Standard Guide for Collecting Skimmer
Performance Data in Uncontrolled Environments.'' ASTM discontinued this
standard in 1997, and recommended that the Coast Guard use F 631,
``Standard Method for Testing Full-Scale Advancing Spill Removal
Devices'' in its place. ASTM F 808 is incorporated in 33 CFR parts 154
(Appendix C) and 155 (Appendix B), which include requirements for
collecting data on performance of oil skimmers. The Coast Guard has
determined that it is appropriate to eliminate ASTM F 808 from the text
without adding a replacement, since the current regulatory text states
that ASTM F 631 or an equivalent test approved by the Coast Guard will
serve as well.
Regulatory Evaluation
This direct final rule is not a significant regulatory action under
section 3(f) of Executive Order 12866 and does not require an
assessment of potential costs and benefits under section 6(a)(3) of
that Order. It has not been reviewed by the Office of Management and
Budget under that Order. It is not significant under the regulatory
policies and procedures of the Department of Transportation (DOT) (44
FR 11040; February 26, 1979). The Coast Guard expects the economic
impact of this rule to be so minimal that a full Regulatory Evaluation
under paragraph 10e of the regulatory policies and procedures of DOT is
unnecessary.
Costs to Industry
This direct final rule involves administrative changes (updates) to
rules that incorporate ASTM standards. Industry will need to purchase
the updated standards. Each business will incur costs based on the
number of standards it must purchase, which will vary greatly. Costs
for purchasing these standards will be minimal. The average cost of an
ASTM standard is $18 to $20. Because of copyright restrictions,
businesses must purchase standards from ASTM.
Benefits to Industry
While it is not possible to accurately quantify the benefits of
requiring industry to use recent versions of ASTM's standards, the net
result will be improved product quality, which translates into improved
maritime safety. Industry already uses these standards in many
applications including the manufacture of searchlights, lifejackets,
immersion suits, and fire-protective equipment, which have direct
implications for safety. Further, since some of the standards have been
discontinued, it will be easier for industry to obtain copies of the
incorporated updated ones from ASTM.
An added benefit is reduced administrative burden. Industry may
already be aware of a new standard and want to use it, but be bound by
rule to using the older standard unless the Coast Guard authorizes,
case by case, the use of a newer version. If the newer version is
already listed, it obviates this need.
Small Entities
Under the Regulatory Flexibility Act (5 U.S.C. 601-612), we
considered whether this direct final rule will have a significant
economic impact on a substantial number of small entities. The term
``small entities'' comprises small businesses, not-for-profit
organizations that are independently owned and operated and are not
dominant in their fields, and governmental jurisdictions with
populations of less than 50,000.
Given the wide range of ASTM standard applications, involving the
manufacture of products such as sheet metal, metal coatings, metal
castings, piping, pressure vessels, plastics, rubber, and many others,
it is not practicable to accurately determine the types and numbers of
small entities affected by this rule.
Because of copyright, as we note, industry must purchase the
standards from ASTM. But the costs associated with purchasing the new
standards are minimal, and the Coast Guard believes that purchasing the
standards will not create a financial burden for any small business.
Therefore, the Coast Guard certifies under 5 U.S.C. 605(b) that
this rule will not have a significant economic impact on a substantial
number of small entities. If you think that your business,
organization, or governmental jurisdiction qualifies as a small entity
and that this rule will have a significant economic impact on it,
please submit a comment to the Docket Management Facility at the
address under ADDRESSES. In your comment, explain why you think it
qualifies and how and to what degree this rule will economically affect
it.
Collection of Information
This direct final rule will not call for new collection of
information under the Paperwork Reduction Act of 1995 (44 U.S.C. 3501-
3520). Indeed, it should reduce administrative difficulty for everyone
affected by it.
Federalism
We have analyzed this direct final rule under E.O. 13132 and have
determined that this rule does not have implications for federalism
under that Order.
Unfunded Mandates Reform Act
The Unfunded Mandates Reform Act of 1995 (2 U.S.C. 1531-1538)
governs the issuance of Federal rules that impose unfunded mandates. An
unfunded mandate is a rule that requires a State, local, or tribal
government or the private sector to incur direct costs without the
Federal Government's having first provided the funds to pay those
costs. This direct final rule will not impose an unfunded mandate.
Taking of Private Property
This direct final rule will not effect a taking of private property
or otherwise have taking implications under E.O. 12630, Governmental
Actions and
[[Page 67174]]
Interference with Constitutionally Protected Property Rights.
Reform of Civil Justice
This direct final rule meets applicable standards in sections 3(a)
and 3(b)(2) of E.O. 12988, Reform of Civil Justice, to minimize
litigation, eliminate ambiguity, and reduce burden.
Protection of Children
We have analyzed this direct final rule under E.O. 13045,
Protection of Children from Environmental Health Risks and Safety
Risks. This rule is not an economically significant rule and does not
concern an environmental risk to health or risk to safety that may
disproportionately affect children.
Environment
We considered the environmental impact of this direct final rule
and concluded that under figure 2-1, paragraph (34)(a) of Commandant
Instruction M16475.lC, this rule is categorically excluded from further
environmental documentation. Under paragraph (34)(a), this exclusion is
appropriate for rules that are ``editorial or procedural, such as those
updating addresses or establishing application procedures.'' A
Determination of Categorical Exclusion is available in the docket where
indicated under ADDRESSES.
List of Subjects
33 CFR Part 127
Fire prevention, Harbors, Incorporation by reference, Natural gas,
Reporting and recordkeeping requirements, Security measures.
33 CFR Part 154
Fire prevention, Hazardous substances, Incorporation by reference,
Oil pollution, Reporting and recordkeeping requirements.
33 CFR Part 155
Hazardous substances, Incorporation by reference, Oil pollution,
Reporting and recordkeeping requirements.
33 CFR Part 159
Incorporation by reference, Sewage disposal, Vessels.
33 CFR Part 164
Incorporation by reference, Marine safety, Navigation (water),
Reporting and recordkeeping requirements, Waterways.
33 CFR Part 183
Incorporation by reference, Marine safety.
46 CFR Part 28
Fire prevention, Fishing vessels, Incorporation by reference,
Marine safety, Occupational safety and health, Reporting and
recordkeeping requirements, Seamen.
46 CFR Part 30
Cargo vessels, Foreign relations, Hazardous materials
transportation, Incorporation by reference, Penalties, Reporting and
recordkeeping requirements, Seamen.
46 CFR Part 32
Cargo vessels, Fire prevention, Incorporation by reference, Marine
safety, Navigation (water), Occupational safety and health, Reporting
and recordkeeping requirements, Seamen.
46 CFR Part 34
Cargo vessels, Fire prevention, Incorporation by reference, Marine
safety.
46 CFR Part 35
Cargo vessels, Incorporation by reference, Marine safety,
Navigation (water), Occupational safety and health, Reporting and
recordkeeping requirements, Seamen.
46 CFR Part 38
Cargo vessels, Fire prevention, Gases, Hazardous materials
transportation, Incorporation by reference, Marine safety, Reporting
and recordkeeping requirements.
46 CFR Part 39
Cargo vessels, Fire prevention, Hazardous materials transportation,
Incorporation by reference, Marine safety, Occupational safety and
health, Reporting and recordkeeping requirements.
46 CFR Part 54
Incorporation by reference, Reporting and recordkeeping
requirements, Vessels.
46 CFR Part 56
Incorporation by reference, Reporting and recordkeeping
requirements, Vessels.
46 CFR Part 58
Incorporation by reference, Reporting and recordkeeping
requirements, Vessels.
46 CFR Part 61
Incorporation by reference, Reporting and recordkeeping
requirements, Vessels.
46 CFR Part 63
Incorporation by reference, Reporting and recordkeeping
requirements, Vessels.
46 CFR Part 76
Fire prevention, Incorporation by reference, Marine safety,
Passenger vessels.
46 CFR Part 77
Incorporation by reference, Marine safety, Navigation (water),
Passenger vessels.
46 CFR Part 78
Incorporation by reference, Marine safety, Navigation (water),
Passenger vessels, Penalties, Reporting and recordkeeping requirements.
46 CFR Part 92
Cargo vessels, Fire prevention, Incorporation by reference, Marine
safety, Occupational safety and health, Seamen.
46 CFR Part 95
Cargo vessels, Fire prevention, Incorporation by reference, Marine
safety.
46 CFR Part 96
Cargo vessels, Incorporation by reference, Marine safety,
Navigation (water).
46 CFR Part 97
Cargo vessels, Incorporation by reference, Marine safety,
Navigation (water), Reporting and recordkeeping requirements.
46 CFR Part 105
Cargo vessels, Fishing vessels, Hazardous materials transportation,
Incorporation by reference, Marine safety, Petroleum, Seamen.
46 CFR Part 108
Fire prevention, Incorporation by reference, Marine safety,
Occupational safety and health, Oil and gas exploration, Vessels.
46 CFR Part 109
Incorporation by reference, Marine safety, Occupational safety and
health, Oil and gas exploration, reporting and recordkeeping
requirements, Vessels.
46 CFR Part 110
Incorporation by reference, Reporting and recordkeeping
requirements, Vessels.
46 CFR Part 111
Incorporation by reference, Vessels.
[[Page 67175]]
46 CFR Part 114
Incorporation by reference, Marine safety, Passenger vessels,
Reporting and recordkeeping requirements.
46 CFR Part 119
Incorporation by reference, Marine safety, Passenger vessels.
46 CFR Part 125
Administrative practice and procedure, Authority delegation,
Hazardous materials transportation, Incorporation by reference, Marine
safety, Offshore supply vessels, Oil and gas exploration, Vessels.
46 CFR Part 151
Cargo vessels, Hazardous materials transportation, Incorporation by
reference, Marine safety, Reporting and recordkeeping requirements,
Water pollution control.
46 CFR Part 153
Administrative practice and procedure, Cargo vessels, Hazardous
materials transportation, Incorporation by reference, Marine safety,
Reporting and recordkeeping requirements, Water pollution control.
46 CFR Part 154
Cargo vessels, Gases, Hazardous materials transportation,
Incorporation by reference, Marine safety, Reporting and recordkeeping
requirements.
46 CFR Part 160
Incorporation by reference, Marine safety, Reporting and
recordkeeping requirements.
46 CFR Part 161
Fire prevention, Incorporation by reference, Marine safety,
Reporting and recordkeeping requirements.
46 CFR Part 162
Fire prevention, Incorporation by reference, Marine safety, Oil
pollution, Reporting and recordkeeping requirements.
46 CFR Part 163
Incorporation by reference, Marine safety.
46 CFR Part 164
Applicable Specification and Referenced Material, Fire prevention,
Incorporation by reference, Marine safety, Reporting and recordkeeping
requirements.
46 CFR Part 170
Incorporation by reference, Marine safety, Reporting and
recordkeeping requirements, Vessels.
46 CFR Part 174
Incorporation by reference, Marine safety, Vessels.
46 CFR Part 175
Incorporation by reference, Marine safety, Passenger vessels,
Reporting and recordkeeping requirements.
46 CFR Part 182
Incorporation by reference, Marine safety, Passenger vessels.
46 CFR Part 190
Fire prevention, Incorporation by reference, Marine safety,
Occupational safety and health, Oceanographic research vessels.
46 CFR Part 193
Fire prevention, Incorporation by reference, Marine safety,
Oceanographic research vessels.
46 CFR Part 195
Incorporation by reference, Marine Safety, Navigation (water),
Oceanographic research vessels.
46 CFR Part 199
Cargo vessels, Incorporation by reference, Marine Safety, Oil and
Gas exploration, Passenger vessels.
For the reasons discussed in the preamble, the Coast Guard amends
33 CFR parts 127, 154, 155, 159, 164, and 183 and 46 CFR parts 28, 30,
32, 34, 35, 38, 39, 54, 56, 58, 61, 63, 76, 77, 78, 92, 95, 96, 97,
105, 108, 109, 110, 111, 114, 119, 125, 151, 153, 154, 160, 161, 162,
163, 164, 170, 174, 175, 182, 190, 193, 195, and 199 as follows:
TITLE 33--[AMENDED]
PART 127--WATERFRONT FACILITIES HANDLING LIQUEFIED NATURAL GAS AND
LIQUEFIED HAZARDOUS GAS
1. The authority citation for part 127 continues to read as
follows:
Authority: 33 U.S.C. 1231; 49 CFR 1.46.
2. In Sec. 127.003(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 127.003 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM F 1121-87 (1993), Standard Specification for International Shore
Connections for Marine Fire Applications--127.611; 127.1511.
* * * * *
PART 154--FACILITIES TRANSFERRING OIL OR HAZARDOUS MATERIAL IN BULK
3. Revise the authority citation for part 154 to read as follows:
Authority: 33 U.S.C. 1231, 1321(j)(1)(C), (j)(5), (j)(6), and
(m)(2); sec. 2, E.O. 12777, 56 FR 54757; 49 CFR 1.46. Subpart F is
also issued under 33 U.S.C. 2735.
4. In Sec. 154.106(b), revise the entry for ``American Society for
Testing Materials'' to read as follows:
Sec. 154.106 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM F 631-93, Standard Guide for Collecting Skimmer Performance Data
in Controlled Environments--Appendix C
ASTM F 715-95, Standard Test Methods for Coated Fabrics Used for Oil
Spill Control and Storage--Appendix C
ASTM F 722-82 (1993), Standard Specification for Welded Joints for
Shipboard Piping Systems--Appendix A; Appendix B
ASTM F 1122-87 (1992), Standard Specification for Quick Disconnect
Couplings--154.500
ASTM F 1155-98, Standard Practice for Selection and Application of
Piping System Materials--Appendix A; Appendix B
* * * * *
Appendix C to Part 154 [Amended]
5-7. In Appendix C to part 154, in paragraph 2.3.1, remove the
words ``, ASTM F 989,''; in paragraph 6.3, remove the words ``, ASTM F
808,''; and, in paragraph 6.3.1, remove the number ``13.1.15'' and add,
in its place, the number ``13.2.16''.
PART 155--OIL OR HAZARDOUS MATERIAL POLLUTION PREVENTION
REGULATIONS FOR VESSELS
8. The authority citation for part 155 continues to read as
follows:
Authority: 33 U.S.C. 1231, 1321(j); 46 U.S.C. 3715; sec. 2, E.O.
12777, 56 FR 54757, 3 CFR, 1991 Comp., p. 351; 49 CFR 1.46.
Sections 155.100 through 155.130, 155.350 through 155.400, 155.430,
155.440, 155.470, 155.1030(j) and (k), and 155.1065(g) also issued
under 33 U.S.C. 1903(b); and Secs. 155.1110 through 155.1150 also
issued under 33 U.S.C. 2735.
[[Page 67176]]
9. In Sec. 155.140(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 155.140 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM F 631-93, Standard Guide for Collecting Skimmer Performance Data
in Controlled Environments--Appendix B
ASTM F 715-95, Standard Test Methods for Coated Fabrics Used for Oil
Spill Control and Storage--Appendix B
ASTM F 722-82 (1993), Standard Specification for Welded Joints for
Shipboard Piping Systems--Appendix A; Appendix B
* * * * *
Appendix B to Part 155 [Amended]
10. In Appendix B to part 155--
a. In paragraph 2.4, remove the words ``ASTM F 715-81 (Reapproved
1986),'' and add, in their place, the words ``ASTM F 715 (incorporated
by reference, see Sec. 155.140)''; and remove the words ``and ASTM F
989-86, Standard Test Methods for Spill Control Barrier Tension
Members'';
b. In paragraph 6.3, remove the words ``ASTM F 631-80, Reapproved
1985)'' and add, in their place, the words ``ASTM F 631 (incorporated
by reference, see Sec. 155.140)''; and remove the words ``, and ASTM F
808-83 (1988), Standard Guide for Collecting Skimmer Performance Data
in Uncontrolled Environments''; and
c. In paragraph 6.3.1, remove the words ``Item 26 in ASTM F 808;''
and remove the number ``13.1.15'' and add, in its place, the number
``13.2.16''.
PART 159--MARINE SANITATION DEVICES
11. The authority citation for part 159 continues to read as
follows:
Authority: Sec. 312(b)(1), 86 Stat. 871 (33 U.S.C. 1322(b)(1));
49 CFR 1.45(b) and 1.46 (l) and (m).
12. Add Sec. 159.4 to read as follows:
Sec. 159.4 Incorporation by reference.
(a) Certain material is incorporated by reference into this part
with the approval of the Director of the Federal Register under 5
U.S.C. 552(a) and 1 CFR part 51. To enforce any edition other than that
specified in paragraph (b) of this section, the Coast Guard must
publish notice of change in the Federal Register; and the material must
be available to the public. All approved material is available for
inspection at the Office of the Federal Register, 800 North Capitol
Street, NW., suite 700, Washington, DC, and at the U.S. Coast Guard
Office of Design and Engineering Standards (G-MSE), 2100 Second Street
SW., Washington, DC 20593-0001, and is available from the sources
indicated in paragraph (b) of this section.
(b) The material approved for incorporation by reference in this
part, and the sections affected, are as follows:
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM E 11-95, Standard Specification for Wire Cloth and Sieves for
Testing Purposes--159.125
Sec. 159.125 [Amended]
13. In Sec. 159.125, remove the words ``ASTM E-11-70'' and add, in
their place, the words ``ASTM E 11 (incorporated by reference, see
Sec. 159.4)''.
PART 164--NAVIGATION SAFETY REGULATIONS
14. The authority citation for part 164 continues to read as
follows:
Authority: 33 U.S.C. 1223, 1231; 46 U.S.C. 2103, 3703; 49 CFR
1.46. Sec. 164.13 also issued under 46 U.S.C. 8502. Sec. 164.61 also
issued under 46 U.S.C. 6101.
Sec. 164.03 [Amended]
15. In Sec. 164.03(b), under the entry for ``American Society for
Testing and Materials'', remove the words ``1916 Race Street,
Philadelphia, PA 19103'' and add, in their place, the words ``100 Barr
Harbor Drive, West Conshohocken, PA 19428-2959''.
Sec. 164.74 [Amended]
16. In Sec. 164.74(a)(3) (i) and (ii), remove the words ``ASTM
D4268-93'', wherever they appear, and add, in their place, the words
``ASTM D 4268 (incorporated by reference, see Sec. 164.03)''.
PART 183--BOATS AND ASSOCIATED EQUIPMENT
17. The authority citation for part 183 continues to read as
follows:
Authority: 46 U.S.C. 4302; 49 CFR 1.46.
18. In Sec. 183.5(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 183.5 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM D 471-96, Standard Test Method for Rubber Property--Effect of
Liquids--183.114; 183.516; 183.607; 183.620
ASTM D 1621-94, Standard Test Method for Compressive Properties of
Rigid Cellular Plastics--183.516
ASTM D 1622-93, Standard Test Method for Apparent Density of Rigid
Cellular Plastics--183.516
ASTM D 2842-97, Standard Test Method for Water Absorption of Rigid
Cellular Plastics--183.114
* * * * *
Sec. 183.110 [Amended]
19. In Sec. 183.110, remove the definition of ``ASTM''.
Sec. 183.620 [Amended]
20. In Sec. 183.620, in the note following paragraph (a)(5)(ii),
remove the number ``D-471-1979'' and add, in its place, the words ``D
471 (incorporated by reference, see Sec. 183.5)''.
TITLE 46--[AMENDED]
PART 28--REQUIREMENTS FOR COMMERCIAL FISHING INDUSTRY VESSELS
21. The authority citation for part 28 continues to read as
follows:
Authority: 46 U.S.C. 3316, 4502, 4505, 4506, 6104, 10603; 49 CFR
1.46.
22. In Sec. 28.40(b), add an entry for ``American Society for
Testing and Materials'' in alphabetical order to read as follows:
Sec. 28.40 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM F 1321-92, Standard Guide for Conducting a Stability Test
(Lightweight Survey and Inclining Experiment) to Determine the Light
Ship Displacement and Centers of Gravity of a Vessel--28.535
* * * * *
Sec. 28.535 [Amended]
23. In Sec. 28.535(d), remove the words ``ASTM Standard F 1321-90''
and add, in their place, the words ``ASTM F 1321 (incorporated by
reference, see Sec. 28.40)''.
[[Page 67177]]
PART 30--GENERAL PROVISIONS
24. The authority citation for part 30 continues to read as
follows:
Authority: 46 U.S.C. 2103, 3306, 3703; 49 U.S.C. 5103, 5106; 49
CFR 1.45, 1.46; Section 30.01-2 also issued under the authority of
44 U.S.C. 3507; Section 30.01-5 also issued under the authority of
Sec. 4109, Pub. L. 101-380, 104 Stat. 515.
25. Add Sec. 30.01-3 to read as follows:
Sec. 30.01-3 Incorporation by reference.
(a) Certain material is incorporated by reference into this part
with the approval of the Director of the Federal Register under 5
U.S.C. 552(a) and 1 CFR part 51. To enforce any edition other than that
specified in paragraph (b) of this section, the Coast Guard must
publish notice of change in the Federal Register; and the material must
be available to the public. All approved material is available for
inspection at the Office of the Federal Register, 800 North Capitol
Street, NW., suite 700, Washington, DC, and at the U.S. Coast Guard
Office of Design and Engineering Standards (G-MSE), 2100 Second Street
SW., Washington, DC 20593-0001, and is available from the sources
indicated in paragraph (b) of this section.
(b) The material approved for incorporation by reference in this
part, and the sections affected are as follows:
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM D 323-94, Standard Test Method for Vapor Pressure of Petroleum
Products (Reid Method)--30.10-22; 30.10-59
PART 32--SPECIAL EQUIPMENT, MACHINERY, AND HULL REQUIREMENTS
26. The authority citation for part 32 continues to read as
follows:
Authority: 46 U.S.C. 2103, 3306, 3703; E.O. 12234, 3 CFR, 1980
Comp., p. 277; 49 CFR 1.46; Section 32.22T-5 and subpart 32.59 also
issued under 46 U.S.C. 3703 note.
27. In Sec. 32.01-1(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 32.01-1 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM D 4986-98, Standard Test Method for Horizontal Burning
Characteristics of Cellular Polymeric Materials--32.57-10
ASTM F 1273-91 (1997), Standard Specification for Tank Vent Flame
Arresters--32.20-10
Sec. 32.57-10 [Amended]
28. In Sec. 32.57-10(d)(7-a), remove the words ``American Society
for Testing and Materials (ASTM) Specification D-1692, `Rate of Burning
or Extent of Burning of Cellular Plastics Using a Supported Specimen by
a Horizontal Screen' '' and add, in their place, the words ``ASTM D
4986, `Standard Test Method for Horizontal Burning Characteristics of
Cellular Polymeric Materials' (incorporated by reference, see
Sec. 32.01-1)''.
PART 34--FIREFIGHTING EQUIPMENT
29. The authority citation for part 34 continues to read as
follows:
Authority: 46 U.S.C. 3306, 3703; E.O. 12234, 45 FR 58801, 3 CFR,
1980 Comp., p. 277; 49 CFR 1.46.
Sec. 34.01-15 [Amended]
30. In Sec. 34.01-15(b), remove the words ``ASTM F-1121'' and add,
in their place, ``ASTM F 1121-87 (Reapproved 1993)''.
PART 35--OPERATIONS
31. The authority citation for part 35 continues to read as
follows:
Authority: 33 U.S.C. 1321(j); 46 U.S.C. 3306, 3703, 6101; 49
U.S.C. 5103, 5106; E.O. 12234, 45 FR 58801, 3 CFR, 1980 Comp., p.
277; E.O. 12777, 56 FR 54757, 3 CFR, 1991 Comp., p. 351; 49 CFR
1.46.
32. In Sec. 35.01-3(b), remove the words ``ASTM F1014-1986'' and
add, in their place, the words ``ASTM F 1014-92''; and add an entry for
``ASTM D 93'' to read as follows:
Sec. 35.01-3 Incorporation by reference.
* * * * *
(b) * * *
ASTM D 93-97, Standard Test Methods for Flash-Point by Pensky-
Martens Closed Cup Tester--35.25-10
* * * * *
Sec. 35.30-20 [Amended]
33. In Sec. 35.30-20(c)(3), remove the words ``ASTM F1014-1986''
and add, in their place, the words ``ASTM F 1014 (incorporated by
reference, see Sec. 35.01-3)''.
PART 38--LIQUEFIED FLAMMABLE GASES
34. The authority citation for part 38 continues to read as
follows:
Authority: 46 U.S.C. 2103, 3306, 3703; 49 U.S.C. 5101, 5106;
E.O. 12234, 45 FR 58801, 3 CFR, 1980 Comp., p. 277; 49 CFR 1.46.
35. In Sec. 38.01-3(b), add an entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 38.01-3 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM D 4986-98, Standard Test Method for Horizontal Burning
Characteristics of Cellular Polymeric Materials--38.05-20
* * * * *
Sec. 38.05-20 [Amended]
36. In Sec. 38.05-20(a)(1)(ii), remove the words ``American Society
for Testing and Materials Specification D-1692, `Flammability of
Plastics, Foam and Sheeting,' '' and add, in their place, ``ASTM D
4986, `Standard Test Method for Horizontal Burning Characteristics of
Cellular Polymeric Materials,' (incorporated by reference, see
Sec. 38.01-3)''.
PART 39--VAPOR CONTROL SYSTEMS
37. The authority citation for part 39 continues to read as
follows:
Authority: 33 U.S.C. 1231; 46 U.S.C. 3306, 3703, 3715(b); 45 FR
58801, 3 CFR, 1980 Comp., p. 277; 49 CFR 1.46.
Sec. 39.10-5 [Amended]
38. In Sec. 39.10-5(b), remove the words ``ASTM F 1271'' and add,
in their place, the words ``ASTM F 1271-90 (1995)''; and remove the
words ``, December 29, 1989''.
PART 54--PRESSURE VESSELS
39. The authority citation for part 54 continues to read as
follows:
Authority: 33 U.S.C. 1509; 43 U.S.C. 1333; 46 U.S.C. 3306, 3703;
E.O. 12234, 45 FR 58801, 3 CFR, 1980 Comp., p. 277; 49 CFR 1.46.
40. In Sec. 54.01-1(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 54.01-1 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
[[Page 67178]]
ASTM A 20/A 20M-97a, Standard Specification for General Requirements
for Steel Plates for Pressure Vessels--54.05-10; 54.25-10
ASTM A 203/A 203M-97, Standard Specification for Pressure Vessel
Plates, Alloy Steel, Nickel--54.05-20
ASTM A 370-97a, Standard Test Methods and Definitions for Mechanical
Testing of Steel Products--54.25-20
ASTM E 23-96, Standard Test Methods for Notched Bar Impact Testing of
Metallic Materials--54.05-5
ASTM E 208-95a, Standard Test Method for Conducting Drop-Weight Test to
Determine Nil-Ductility Transition Temperature of Ferritic Steels--
54.05-5
* * * * *
Sec. 54.05-10 [Amended]
41. In Sec. 54.05-10(a), remove the words ``as outlined in section
4(b) of ASTM A-300'' and add, in their place, the words ``as outlined
in section 12 of ASTM A 20 (incorporated by reference, see Sec. 54.01-
1)''.
Sec. 54.25-10 [Amended]
42. In Sec. 54.25-10, remove paragraphs (d)(1)(v) and (d)(2)(ii);
redesignate paragraphs (d)(1)(vi) through (d)(1)(viii) as (d)(1)(v)
through (d)(1)(vii); and redesignate paragraphs (d)(2)(iii) through
(d)(2)(ix) as (d)(2)(ii) through (d)(2)(viii).
PART 56--PIPING SYSTEMS AND APPURTENANCES
43. The authority citation for part 56 continues to read as
follows:
Authority: 33 U.S.C. 1321(j), 1509; 43 U.S.C. 1333; 46 U.S.C.
3306, 3703; E.O. 12234, 45 FR 58801, 3 CFR, 1980 Comp., p. 277;
E.O.12777, 56 FR 54757, 3 CFR, 1991 Comp., p. 351; 49 CFR 1.46.
44. In Sec. 56.01-2(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 56.01-2 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM A 36/A 36M-97a, Standard Specification for Carbon Structural
Steel--56.30-10
ASTM A 47-90 (1995), Standard Specification for Ferritic Malleable Iron
Castings--56.60-1
ASTM A 53-98, Standard Specification for Pipe, Steel, Black and Hot-
Dipped, Zinc-Coated, Welded and Seamless--56.10-5; 56.60-1
ASTM A 106-95, Standard Specification for Seamless Carbon Steel Pipe
for High-Temperature Service--56.60-1
ASTM A 126-95, Standard Specification for Gray Iron Castings for
Valves, Flanges, and Pipe Fittings--56.60-1
ASTM A 134-96, Standard Specification for Pipe, Steel, Electric-Fusion
(Arc)-Welded (Sizes NPS 16 and Over)--56.60-1
ASTM A 135-97c, Standard Specification for Electric-Resistance-Welded
Steel Pipe--56.60-1
ASTM A 139-96, Standard Specification for Electric-Fusion (Arc)-Welded
Steel Pipe (NPS 4 and Over)--56.60-1
ASTM A 178/A 178M-95, Standard Specification for Electric-Resistance-
Welded Carbon Steel and Carbon-Manganese Steel Boiler and Superheater
Tubes--56.60-1
ASTM A 179/A 179M-90a (1996), Standard Specification for Seamless Cold-
Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes--56.60-1
ASTM A 182/A 182M-97c, Standard Specification for Forged or Rolled
Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for
High-Temperature Service--56.50-105
ASTM A 192/A 192M-91 (1996), Standard Specification for Seamless Carbon
Steel Boiler Tubes for High-Pressure Service--56.60-1
ASTM A 194/A 194M-98b, Standard Specification for Carbon and Alloy
Steel Nuts for Bolts for High Pressure or High Temperature Service, or
Both--56.50-105
ASTM A 197-87 (1992), Standard Specification for Cupola Malleable
Iron--56.60-1
ASTM A 210/A 210M-96, Standard Specification for Seamless Medium-Carbon
Steel Boiler and Superheater Tubes--56.60-1
ASTM A 213/A 213M-95a, Standard Specification for Seamless Ferritic and
Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes--
56.60-1
ASTM A 214/A 214M-96, Standard Specification for Electric-Resistance-
Welded Carbon Steel Heat-Exchanger and Condenser Tubes--56.60-1
ASTM A 226/A 226M-95, Standard Specification for Electric-Resistance-
Welded Carbon Steel Boiler and Superheater Tubes for High-Pressure
Service--56.60-1
ASTM A 234/A 234M-97, Standard Specification for Piping Fittings of
Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature
Service--56.60-1
ASTM A 249/A 249M-96a, Standard Specification for Welded Austenitic
Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes--56.60-1
ASTM A 268/A 268M-96, Standard Specification for Seamless and Welded
Ferritic and Martensitic Stainless Steel Tubing for General Service--
56.60-1
ASTM A 276-98, Standard Specification for Stainless Steel Bars and
Shapes--56.60-2
ASTM A 307-97, Standard Specification for Carbon Steel Bolts and Studs,
60,000 PSI Tensile Strength--56.25-20
ASTM A 312/A 312M-95a, Standard Specification for Seamless and Welded
Austenitic Stainless Steel Pipes--56.50-105; 56.60-1
ASTM A 320/A 320M-97, Standard Specification for Alloy/Steel Bolting
Materials for Low-Temperature Service--56.50-105
ASTM A 333/A 333M-94, Standard Specification for Seamless and Welded
Steel Pipe for Low-Temperature Service--56.50-105; 56.60-1
ASTM A 334/A 334M-96, Standard Specification for Seamless and Welded
Carbon and Alloy-Steel Tubes for Low-Temperature Service--56.50-105;
56.60-1
ASTM A 335/A 335M-95a, Standard Specification for Seamless Ferritic
Alloy-Steel Pipe for High-Temperature Service--56.60-1
ASTM A 350/A 350M-97, Standard Specification for Carbon and Low-Alloy
Steel Forgings, Requiring Notch Toughness Testing for Piping
Components--56.50-105
ASTM A 351/A 351M-94a, Standard Specification for Castings, Austenitic,
Austenitic-Ferritic (Duplex), for Pressure-Containing Parts--56.50-105
ASTM A 352/A 352M-93 (1998), Standard Specification for Steel Castings,
Ferritic and Martensitic, for Pressure-Containing Parts, Suitable for
Low-Temperature Service--56.50-105
ASTM A 358/A 358M-95a, Standard Specification for Electric-Fusion-
Welded Austenitic Chromium-Nickel Alloy Steel Pipe for High-Temperature
Service--56.60-1
ASTM A 369/A 369M-92, Standard Specification for Carbon and Ferritic
Alloy Steel Forged and Bored Pipe for High-Temperature Service--56.60-1
ASTM A 376/A 376M-96, Standard Specification for Seamless Austenitic
Steel Pipe for High-Temperature
[[Page 67179]]
Central-Station Service--56.07-10; 56.60-1; 56.60-2
ASTM A 395/A 395M-98, Standard Specification for Ferritic Ductile Iron
Pressure-Retaining Castings for Use at Elevated Temperatures--56.50-60;
56.60-1; 56.60-15
ASTM A 403/A 403M-98, Standard Specification for Wrought Austenitic
Stainless Steel Piping Fittings--56.60-1
ASTM A 420/A 420M-96a, Standard Specification for Piping Fittings of
Wrought Carbon Steel and Alloy Steel for Low-Temperature Service--
56.50-105; 56.60-1
ASTM A 520-97, Standard Specification for Supplementary Requirements
for Seamless and Electric-Resistance-Welded Carbon Steel Tubular
Products for High-Temperature Service Conforming to ISO Recommendations
for Boiler Construction--56.60-1
ASTM A 522/A 522M-95b, Standard Specification for Forged or Rolled 8
and 9% Nickel Alloy Steel Flanges, Fittings, Valves, and Parts for Low-
Temperature Service--56.50-105
ASTM A 536-84 (1993), Standard Specification for Ductile Iron
Castings--56.60-1
ASTM A 575-96, Standard Specification for Steel Bars, Carbon, Merchant
Quality, M-Grades--56.60-2
ASTM A 576-90b (1995), Standard Specification for Steel Bars, Carbon,
Hot-Wrought, Special Quality--56.60-2
ASTM B 16-92, Standard Specification for Free-Cutting Brass Rod, Bar,
and Shapes for Use in Screw Machines--56.60-2
ASTM B 21-96, Standard Specification for Naval Brass Rod, Bar, and
Shapes--56.60-2
ASTM B 26/B 26M-97, Standard Specification for Aluminum-Alloy Sand
Castings--56.60-2
ASTM B 42-96, Standard Specification for Seamless Copper Pipe, Standard
Sizes--56.60-1
ASTM B 43-96, Standard Specification for Seamless Red Brass Pipe,
Standard Sizes--56.60-1
ASTM B 68-95, Standard Specification for Seamless Copper Tube, Bright
Annealed--56.60-1
ASTM B 75-97, Standard Specification for Seamless Copper Tube--56.60-1
ASTM B 85-96, Standard Specification for Aluminum-Alloy Die Castings--
56.60-2
ASTM B 88-96, Standard Specification for Seamless Copper Water Tube--
56.60-1
ASTM B 96-93, Standard Specification for Copper-Silicon Alloy Plate,
Sheet, Strip, and Rolled Bar for General Purposes and Pressure
Vessels--56.60-2
ASTM B 111-95, Standard Specification for Copper and Copper-Alloy
Seamless Condenser Tubes and Ferrule Stock--56.60-1
ASTM B 124-96, Standard Specification for Copper and Copper Alloy
Forging Rod, Bar, and Shapes--56.60-2
ASTM B 161-93, Standard Specification for Nickel Seamless Pipe and
Tube--56.60-1
ASTM B 165-93, Standard Specification of Nickel-Copper Alloy (UNS
NO4400) Seamless Pipe and Tube--56.60-1
ASTM B 167-97a, Standard Specification for Nickel-Chromium-Iron Alloys
(UNS NO6600, NO6601, NO6603, NO6690, NO6025, and NO6045) Seamless Pipe
and Tube--56.60-1
ASTM B 171-95, Standard Specification for Copper-Alloy Plate and Sheet
for Pressure Vessels, Condensers, and Heat Exchangers--56.60-2
ASTM B 210-95, Standard Specification for Aluminum and Aluminum-Alloy
Drawn Seamless Tubes--56.60-1
ASTM B 234-95, Standard Specification for Aluminum and Aluminum-Alloy
Drawn Seamless Tubes for Condensers and Heat Exchangers--56.60-1
ASTM B 241/B 241M-96, Standard Specification for Aluminum and Aluminum-
Alloy Seamless Pipe and Seamless Extruded Tube--56.60-1
ASTM B 280-97, Standard Specification for Seamless Copper Tube for Air
Conditioning and Refrigeration Field Service--56.60-1
ASTM B 283-96, Standard Specification for Copper and Copper-Alloy Die
Forgings (Hot-Pressed)--56.60-2
ASTM B 315-93, Standard Specification for Seamless Copper Alloy Pipe
and Tube--56.60-1
ASTM B 361-95, Standard Specification for Factory-Made Wrought Aluminum
and Aluminum-Alloy Welding Fittings--56.60-1
ASTM B 858M-95, Standard Test Method for Determination of
Susceptibility to Stress Corrosion Cracking in Copper Alloys Using an
Ammonia Vapor Test--56.60-2
ASTM D 635-97, Standard Test Method for Rate of Burning and/or Extent
and Time of Burning of Plastics in a Horizontal Position--56.60-25
ASTM D 1785-96b, Standard Specification for Poly (Vinyl Chloride)(PVC)
Plastic Pipe, Schedules 40, 80, and 120--56.60-25
ASTM D 2241-96b, Standard Specification for Poly (Vinyl Chloride)(PVC)
Pressure-Rated Pipe (SDR Series)--56.60-25
ASTM D 2464-96a, Standard Specification for Threaded Poly (Vinyl
Chloride)(PVC) Plastic Pipe Fittings Schedule 80--56.60-25
ASTM D 2466-97, Standard Specification for Poly (Vinyl Chloride)(PVC)
Plastic Pipe Fittings, Schedule 40--56.60-25
ASTM D 2467-96a, Standard Specification for Poly (Vinyl Chloride)(PVC)
Plastic Pipe Fittings, Schedule 80--56.60-25
ASTM D 2665-97b, Standard Specification for Poly (Vinyl
Chloride)(PVC)Plastic Drain, Waste, and Vent Pipe and Fittings--56.60-
25
ASTM D 2863-95, Standard Test Method for Measuring the Minimum Oxygen
Concentration to Support Candle-like Combustion of Plastics (Oxygen
Index)--56.60-25
ASTM E 23-96, Standard Test Methods for Notched Bar Impact Testing of
Metallic Materials--56.50-105
ASTM F 682-82a (1993), Standard Specification for Wrought Carbon Steel
Sleeve-Type Pipe Couplings--56.60-1
ASTM F 1006-86 (1992), Standard Specification for Entrainment
Separators for Use in Marine Piping Applications--56.60-1
ASTM F 1007-86 (1996), Standard Specification for Pipe-Line Expansion
Joints of the Packed Slip Type for Marine Application--56.60-1
ASTM F 1020-86 (1996), Standard Specification for Line-Blind Valves for
Marine Applications--56.60-1
ASTM F 1120-87 (1993), Standard Specification for Circular Metallic
Bellows Type Expansion Joints for Piping Applications--56.60-1
ASTM F 1123-87 (1993), Standard Specification for Non-Metallic
Expansion Joints--56.60-1
ASTM F 1139-88 (1993), Standard Specification for Steam Traps and
Drains--56.60-2
ASTM F 1172-88 (1993), Standard Specification for Fuel Oil Meters of
the Volumetric Positive Displacement Type--56.60-1
ASTM F 1173-95, Standard Specification for Thermosetting Resin
Fiberglass Pipe and Fittings to be Used for Marine Applications--56.60-
1
ASTM F 1199-88 (1993), Standard Specification for Cast (All Temperature
and Pressures) and Welded Pipe Line Strainers (150 psig and 150 Degrees
F Maximum)--56.60-1
ASTM F 1200-88 (1993), Standard Specification for Fabricated (Welded)
Pipe Line Strainers (Above 150 psig and 150 Degrees F)--56.60-1
ASTM F 1201-88 (1993), Standard Specification for Fluid Conditioner
[[Page 67180]]
Fittings in Piping Applications above 0 Degrees F--56.60-1
ASTM F 1387-93, Standard Specification for Performance of Mechanically
Attached Fittings--56.30-25
ASTM F 1476-95a, Standard Specification for Performance of Gasketed
Mechanical Couplings for Use in Piping Applications--56.30-35
ASTM F 1548-94, Standard Specification for the Performance of Fittings
for Use with Gasketed Mechanical Couplings, Used in Piping Applications
56.30-35
* * * * *
Sec. 56.30-25 [Amended]
45. In Sec. 56.30-25(a), remove the words ``ASTM F 1387-93'' and
add, in their place, the words ``ASTM F 1387 (incorporated by
reference, see Sec. 56.01-2)''.
Sec. 56.30-35 [Amended]
46. In Sec. 56.30-35(a), remove the words ``ASTM F 1476-93'' and
add, in their place, the words ``ASTM F 1476 incorporated by reference,
see Sec. 56.01-2)''; and remove the words ``ASTM F 1548-94'' and add,
in their place, the words ``ASTM F 1548 (incorporated by reference, see
Sec. 56.01-2)''.
Sec. 56.60-1 [Amended]
47. In Sec. 56.60-1(a), revise the heading of Table 56.60-1(A) and
the note between the heading and the table itself to read,
respectively, as follows: ``Table 56.60-1(A)-Adopted Specifications and
Standards'' and ``Note: Table 56.60-1(A) replaces Table 126.1 in ANSI
B31.1 and sets forth specifications of pipes, tubing, and fittings
intended for use in piping-systems. The first column lists acceptable
standards from ASTM; the second lists those from ANSI. The Coast Guard
will consider use of alternative pipes, tubing, and fittings when it
receives certification of their mechanical properties. Without this
certification it will restrict use of such alternatives to piping-
systems inside heat exchangers that ensure containment of the material
inside pressure shells.''; and, in the table, remove the entries for
``A430 Austenitic alloy'' and ``A199 Alloy steel condenser tubes''.
Sec. 56.60-2 [Amended]
48. In Sec. 56.60-2, in Table 56.60-2(A), in footnote 7, remove the
words ``ASTM B 858M-95'' and add, in its place, ``ASTM B 858M
(incorporated by reference, see Sec. 56.01-2)''; and, in footnote 9,
remove the words ``ASTM B 858-95'' and add, in its place, ``ASTM B 858
(incorporated by reference, see Sec. 56.01-2)''.
PART 58--MAIN AND AUXILIARY MACHINERY AND RELATED SYSTEMS
49. The authority citation for part 58 continues to read as
follows:
Authority: 43 U.S.C. 1333; 46 U.S.C. 3306, 3703; E.O. 12234, 45
FR 58801, 3 CFR, 1980 Comp., p. 277; 49 CFR 1.46.
Sec. 58.01-10 [Amended]
50. In Sec. 58.01-10(b), remove the words ``ASTM-D93-80'' and add,
in their place, the words ``ASTM D 93 (incorporated by reference, see
Sec. 58.03-1)''.
51. In Sec. 58.03-1(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 58.03-1 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM A 193/A 193M-98a, Standard Specification for Alloy-Steel and
Stainless Steel Bolting Materials for High-Temperature Service--58.30-
15
ASTM B 96-93, Standard Specification for Copper-Silicon Alloy Plate,
Sheet, Strip, and Rolled Bar for General Purposes and Pressure
Vessels--58.50-5
ASTM B 122/B 122M-95, Standard Specification for Copper-Nickel-Tin
Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel
Alloy Plate, Sheet, Strip, and Rolled Bar--58.50-5
ASTM B 152-97a, Standard Specification for Copper Sheet, Strip, Plate,
and Rolled Bar--58.50-5
ASTM B 209-96, Standard Specification for Aluminum and Aluminum-Alloy
Sheet and Plate--58.50-5; 58.50-10
ASTM D 92-97, Standard Test Method for Flash and Fire Points by
Cleveland Open Cup 58.30-10
ASTM D 93-97, Standard Test Methods for Flash Point by Pensky-Martens
Closed Cup Tester--58.01-10
ASTM D 323-94, Standard Test Method for Vapor Pressure of Petroleum
Products (Reid Method) 58.16-5
* * * * *
Sec. 58.30-10 [Amended]
51a. In Sec. 58.30-10(b), remove the words ``ASTM D92-57'' and add,
in their place, the words ``ASTM D 92 (incorporated by reference, see
Sec. 58.03-1)''.
Sec. 58.50-5 [Amended]
52. In Sec. 58.50-5(a), in Table 58.50-5(A), in the heading of
column two, immediately following the words ``(latest edition)'' add
the words ``[see also Sec. 58.03-1]''; and in column two remove the
words ``B97, Alloys A, B, and C'' and add, in their place, the words
``B 96, alloys C65100 and C65500''.
Sec. 58.50-10 [Amended]
52a. In Sec. 58.50-10(a), in Table 58.50-10(A), in the heading of
column two, immediately following the words ``(latest edition)'' add
the words ``[see also Sec. 58.03-1]''.
PART 61--PERIODIC TESTS AND INSPECTIONS
53. The authority citation for part 61 continues to read as
follows:
Authority: 43 U.S.C. 1333; 46 U.S.C. 2103, 3306, 3703; E.O.
12234, 45 FR 58801, 3 CFR, 1980 Comp., p. 277; 49 CFR 1.46.
54. In Sec. 61.03-1(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 61.03-1 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM D 665-98, Standard Test Method for Rust-Preventing Characteristics
of Inhibited Mineral Oil in the Presence of Water--61.20-17
* * * * *
Sec. 61.20-17 [Amended]
55. In Sec. 61.20-17(a), remove the words ``ASTM D 665-92'' and
add, in their place, the words ``ASTM D 665 (incorporated by reference,
see Sec. 61.03-1)''.
PART 63--AUTOMATIC AUXILIARY BOILERS
56. The authority citation for part 63 continues to read as
follows:
Authority: 46 U.S.C. 3306, 3703; E.O. 12234, 45 FR 58801, 3 CFR,
1980 Comp., p. 277; 49 CFR 1.46.
57. In Sec. 63.05-1(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 63.05-1 Incorporation by reference.
* * * * *
(b) * * *
[[Page 67181]]
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM F 1323-98, Standard Specification for Shipboard Incinerators--
63.25-9
* * * * *
Sec. 63.25-9 [Amended]
58. In Sec. 63.25-9, remove the words ``ASTM F-1323-90'' and add,
in their place, the words ``ASTM F 1323 (incorporated by reference, see
Sec. 63.05-1)''.
PART 76--FIRE PROTECTION EQUIPMENT
59. The authority citation for part 76 continues to read as
follows:
Authority: 46 U.S.C. 3306; E.O. 12234, 45 FR 58801, 3 CFR, 1980
Comp., p. 277; 49 CFR 1.46.
60. In Sec. 76.01-2(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 76.01-2 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM F 1121-87 (1993), Standard Specification for International Shore
Connections for Marine Fire Applications--76.10-10
* * * * *
PART 77--VESSEL CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT
61. The authority citation for part 77 continues to read as
follows:
Authority: 46 U.S.C. 3306; E.O. 12234, 45 FR 58801, 3 CFR 1980
Comp., p. 277; 49 CFR 1.46.
62. In Sec. 77.01-3(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 77.01-3 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM F 1014-92, Standard Specification for Flashlights on Vessels--
77.35-5
Sec. 77.35-5 [Amended]
63. In Sec. 77.35-5(c), remove the words ``ASTM F1014-1986'' and
add, in their place, the words ``ASTM F 1014 (incorporated by
reference, see Sec. 77.01-3)''.
PART 78--OPERATIONS
64. The authority citation for part 78 continues to read as
follows:
Authority: 33 U.S.C. 1321(j); 46 U.S.C. 2103, 3306, 6101; 49
U.S.C. 5103, 5106; E.O. 12234, 45 FR 58801, 3 CFR, 1980 Comp., p.
277; E.O. 12777, 56 FR 54757; 3 CFR, 1991 Comp., p. 351; 49 CFR
1.46.
65. In Sec. 78.01-2(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 78.01-2 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM D 93-97, Standard Test Methods for Flash Point by Pensky-Martens
Closed Cup Tester--78.17-75
* * * * *
PART 92--CONSTRUCTION AND ARRANGEMENT
66. The authority citation for part 92 continues to read as
follows:
Authority: 46 U.S.C. 3306; E.O. 12234, 45 FR 58801, 3 CFR, 1980
Comp., p. 277; 49 CFR 1.46.
Sec. 92.01-2 [Removed]
67. Remove Sec. 92.01-2.
PART 95--FIRE PROTECTION EQUIPMENT
68. The authority citation for part 95 continues to read as
follows:
Authority: 46 U.S.C. 3306; E.O. 12234, 45 FR 58801, 3 CFR, 1980
Comp., p. 277; 49 CFR 1.46.
69. In Sec. 95.01-2(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 95.01-2 Incorporation by reference.
* * * * *
(b) * * *
82. In Sec. 109.105(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM F 1121-87 (1993), Standard Specification for International Shore
Connections for Marine Fire Applications--95.10-10
* * * * *
PART 96--VESSEL CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT
70. The authority citation for part 96 continues to read as
follows:
Authority: 46 U.S.C. 3306; E.O. 12234, 45 FR 58801, 3 CFR, 1980
Comp., p. 277; 49 CFR 1.46.
71. In Sec. 96.01-3(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 96.01-3 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM F 1014-92, Standard Specification for Flashlights on Vessels--
96.35-5
* * * * *
Sec. 96.35-5 [Amended]
72. In Sec. 96.35-5(c), remove the words ``ASTM F1014-1986'' and
add, in their place, the words ``ASTM F 1014 (incorporated by
reference, see Sec. 96.01-3)''.
PART 97--OPERATIONS
73. The authority citation for part 97 continues to read as
follows:
Authority: 33 U.S.C. 1321(j); 46 U.S.C. 2103, 3306, 6101; 49
U.S.C. 5103, 5106; E.O. 12234, 45 FR 58801, 3 CFR, 1980 Comp., p.
277; E.O. 12777, 56 FR 54757; 3 CFR, 1991 Comp., p. 351; 49 CFR
1.46.
74. In Sec. 97.01-2(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 97.01-2 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM D 93-97, Standard Test Methods for Flash Point by Pensky-Martens
Closed Cup Tester--97.15-55
ASTM Adjunct F 1626, Symbols for Use in Accordance with Regulation II-
2/20 of the 1974 SOLAS Convention as amended PCN: 12-616260-01 (1996)--
97.36-1
* * * * *
[[Page 67182]]
PART 105--COMMERCIAL FISHING VESSELS DISPENSING PETROLEUM PRODUCTS
75. The authority citation for part 105 continues to read as
follows:
Authority: 33 U.S.C. 1321(j); 46 U.S.C. 3306, 3703, 4502; 49
U.S.C. App. 1804; E.O. 11735, 38 FR 21243, 3 CFR, 1971-1975 Comp.,
p. 793; 49 CFR 1.46.
76. Add Sec. 105.01-3 to read as follows:
Sec. 105.01-3 Incorporation by reference.
(a) Certain material is incorporated by reference into this part
with the approval of the Director of the Federal Register under 5
U.S.C. 552(a) and 1 CFR part 51. To enforce any edition other than that
specified in paragraph (b) of this section, the Coast Guard must
publish notice of change in the Federal Register; and the material must
be available to the public. All approved material is available for
inspection at the Office of the Federal Register, 800 North Capitol
Street NW., suite 700, Washington, DC, and at the U.S. Coast Guard
Office of Design and Engineering Standards (G-MSE), 2100 Second Street
SW., Washington, DC 20593-0001, and is available from the sources
indicated in paragraph (b) of this section.
(b) The material approved for incorporation by reference in this
part, and the sections affected are as follows:
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM D 323-94, Standard Test Method for Vapor Pressure of Petroleum
Products (Reid Method)--105.10-15
PART 108--DESIGN AND EQUIPMENT
77. The authority citation for part 108 continues to read as
follows:
Authority: 43 U.S.C. 1333; 46 U.S.C. 3102, 3306; 49 CFR 1.46.
78. In Sec. 108.101(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 108.101 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM D 93-97, Standard Test Methods for Flash Point by Pensky-Martens
Closed Cup Tester--108.500
ASTM F 1014-92, Standard Specification for Flashlights on Vessels--
108.497
ASTM F 1121-87 (1993), Standard Specification for International Shore
Connections for Marine Fire Applications--108.427
* * * * *
Sec. 108.497 [Amended]
79. In Sec. 108.497(b), remove the words ``ASTM F1014-1986'' and
add, in their place, the words ``ASTM F 1014 (incorporated by
reference, see Sec. 108.101)''.
Sec. 108.500 [Amended]
80. In Sec. 108.500(b), remove the words ``ASTM D-93-94'' and add,
in their place, the words ``ASTM D 93 (incorporated by reference, see
Sec. 108.101)''.
PART 109--OPERATIONS
81. The authority citation for part 109 continues to read as
follows:
Authority: 43 U.S.C. 1333; 46 U.S.C. 3306, 6101, 10104; 49 CFR
1.46.
82. In Sec. 109.105(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 109.105 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM Adjunct F 1626, Symbols for Use in Accordance with Regulation II-
2/20 of the 1974 SOLAS Convention as amended PCN: 12-616260-01 (1996)--
109.563
* * * * *
PART 110--GENERAL PROVISIONS
83. The authority citation for part 110 continues to read as
follows:
Authority: 33 U.S.C. 1509; 43 U.S.C. 1333; 46 U.S.C. 3306, 3703;
E.O. 12234, 45 FR 58801, 3 CFR, 1980 Comp., p. 277; 49 CFR 1.45,
1.46; Sec. 110.01-2 also issued under 44 U.S.C. 3507.
84. In Sec. 110.10-1(b), revise the entry for ``American Society
for Testing and Materials'' to read as follows:
Sec. 110.10-1 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM B 117-97, Standard Practice for Operating Salt Spray (Fog)
Apparatus--110.15-1
ASTM D 4066-96a, Standard Classification System for Nylon Injection and
Extrusion Materials (PA)--111.60-1
* * * * *
PART 111--ELECTRICAL SYSTEMS--GENERAL ENGINEERING
85. The authority citation for part 111 continues to read as
follows:
Authority: 46 U.S.C. 3306, 3703; 49 CFR 1.46.
Sec. 111.60-1 [Amended]
86. In Sec. 111.60-1(c)(4), remove the words ``ASTM D 4066-94b Type
VIII'' and add, in their place, the words ``ASTM D 4066 (incorporated
by reference, see Sec. 110.10-1 of this chapter)''.
PART 114--GENERAL PROVISIONS
87. The authority citation for part 114 continues to read as
follows:
Authority: 46 U.S.C. 2103, 3306, 3703; 49 U.S.C. App. 1804; 49
CFR 1.45, 1.46. Sec. 114.900 also issued under 44 U.S.C. 3507.
88. In Sec. 114.600(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 114.600 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM B 96-93, Standard Specification for Copper-Silicon Alloy Plate,
Sheet, Strip, and Rolled Bar for General Purposes and Pressure
Vessels--119.440
ASTM B 117-97, Standard Practice for Operating Salt Spray (Fog)
Apparatus--114.400
ASTM B 122/B 122M-95, Standard Specification for Copper-Nickel-Tin
Alloy , Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel
Alloy Plate, Sheet, Strip, and Rolled Bar--119.440
ASTM B 127-98, Standard Specification for Nickel-Copper Alloy (UNS
NO4400) Plate, Sheet, and Strip--119.440
ASTM B 152-97a, Standard Specification for Copper Sheet, Strip, Plate,
and Rolled Bar--119.440
ASTM B 209-96, Standard Specification for Aluminum and Aluminum-Alloy
Sheet and Plate--119.440
ASTM D 93-97, Standard Test Methods for Flash Point by Pensky-Martens
Closed Cup Tester--114.400
ASTM D 635-97, Standard Test Method for Rate of Burning and/or Extent
and Time of Burning of Plastics in a Horizontal Position--119.440
[[Page 67183]]
ASTM D 2863-95, Standard Test Method for Measuring the Minimum Oxygen
Concentration to Support Candle-like Combustion of Plastics (Oxygen
Index)--119.440
ASTM E 84-98, Standard Test Method for Surface Burning Characteristics
of Building Materials--116.405; 116.422; 116.423
ASTM E 648-97, Standard Test Method for Critical Radiant Flux of Floor-
Covering Systems Using a Radiant Heat Energy Source--114.400; 116.423
ASTM E 662-97, Standard Test Method for Specific Optical Density of
Smoke Generated by Solid Materials--114.400; 116.423
* * * * *
PART 119--ADDITIONAL EQUIPMENT
89. The authority citation for part 119 continues to read as
follows:
Authority: 46 U.S.C. 2103, 3306; E.O. 12234, 45 FR 58801, 3 CFR,
1980 Comp., p. 277; 49 CFR 1.46.
Sec. 119.440 [Amended]
90. In Sec. 119.440(a)(1), in Table 119.440(A)(1), in the heading
of column two, immediately following the words ``(latest edition)'' add
the words ``[see also Sec. 114.600 of this chapter]''; and in column
two, remove the words ``B97, Alloys A, B, and C'' and add, in their
place, the words ``B 96, alloys C65100 and C65500''.
PART 125--GENERAL
91. The authority citation for part 125 continues to read as
follows:
Authority: 46 U.S.C. 2103, 3306, 3307; 49 U.S.C. App. 1804; 49
CFR 1.46.
92. In Sec. 125.180(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 125.180 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM D 93-97, Standard Test Methods for Flash Point by Pensky-Martens
Closed Cup Tester--128.310
* * * * *
PART 151--BARGES CARRYING BULK LIQUID HAZARDOUS MATERIAL CARGOES
93. The authority citation for part 151 continues to read as
follows:
Authority: 33 U.S.C. 1903; 46 U.S.C. 3703; 49 CFR 1.46.
94. In Sec. 151.01-2(b), add an entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 151.01-2 Incorporation by reference.
* * * * *
(b)* * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM D 4986-98, Standard Test Method for Horizontal Burning
Characteristics of Cellular Polymeric Materials--151.15-3
ASTM E 84-98, Standard Test Method for Surface Burning Characteristics
of Building Materials--151.15-3
* * * * *
Sec. 151.15-3 [Amended]
95. In Sec. 151.15-3(g)(2)(iii), remove the words ``D-1692,
``Flammability of Plastics'' '' and add, in their place, the words ``D
4986, ``Horizontal Burning Characteristics of Cellular Polymeric
Materials'' (incorporated by reference, see Sec. 151.01-2)''.
PART 153--SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED
GAS HAZARDOUS MATERIALS
96. The authority citation for part 153 continues to read as
follows:
Authority: 46 U.S.C. 3703; 49 CFR 1.46. Section 153.40 issued
under 49 U.S.C. 5103. Sections 153.470 through 153.491, 153.1100
through 153.1132, and 153.1600 through 153.1608 also issued under 33
U.S.C. 1903(b).
97. In Sec. 153.4(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 153.4 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM F 1122-87 (1992), Standard Specification for Quick Disconnect
Couplings--153.940
ASTM F 1271-90 (1995), Standard Specification for Spill Valves for Use
in Marine Tank Liquid Overpressure Protections Applications--153.365
* * * * *
PART 154--SAFETY STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK
LIQUEFIED GASES
98. The authority citation for part 154 continues to read as
follows:
Authority: 46 U.S.C. 3703, 9101; 49 CFR 1.46.
99. In Sec. 154.1(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 154.1 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM A 20/A 20M-97a, Standard Specification for General Requirements
for Steel Plates for Pressure Vessels--154.610
ASTM F 1014-92, Standard Specification for Flashlights on Vessels--
154.1400
* * * * *
Sec. 154.610 [Amended]
100. In Sec. 154.610(c), remove the words ``ASTM A-20-75'' and add,
in their place, the words ``ASTM A 20 (incorporated by reference, see
Sec. 154.1)''.
Sec. 154.1400 [Amended]
101. In Sec. 154.1400, remove the words ``ASTM F1014-1986''
wherever they appear and add, in their place, the words ``ASTM F 1014
(incorporated by reference, see Sec. 154.1)''.
PART 160--LIFESAVING EQUIPMENT
102. The authority citation for part 160 continues to read as
follows:
Authority: 46 U.S.C. 2103, 3306, 3703, and 4302; E.O. 12234, 45
FR 58801, 3 CFR, 1980 Comp., p. 277; 49 CFR 1.46.
103. In Sec. 160.032-1, revise paragraph (a)(1) to read as follows;
and, in paragraph (b), remove the words ``The A.S.T.M. Standards may be
purchased from the American Society for Testing Materials, 1916 Race
Street, Philadelphia, Pa., 19103'' and add, in their place, the words
``You may purchase the standards of ASTM from the American Society for
Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA
19428-2959'':
Sec. 160.032-1 Applicable Specifications.
(a) * * *
(1) Standards of ASTM:
ASTM A 27/ A 27M-95, Standard Specification for Steel Castings, Carbon,
for General Application--160.032-3
ASTM A 36/A 36M-97a, Standard Specification for Carbon Structural
Steel--160.032-3
ASTM A 216/A 216M-93 (1998), Standard Specification for Steel
[[Page 67184]]
Castings, Carbon, Suitable for Fusion Welding for High-Temperature
Service--160.032-3
* * * * *
Sec. 160.032-3 [Amended]
104. In Sec. 160.032-3(c), remove the words ``A.S.T.M. Standard
Specification A7'' and add, in their place, the words ``ASTM A 36/A 36
M (incorporated by reference, see Sec. 160.032-1)''.
105. In Sec. 160.035-1, revise paragraph (a)(1) to read as follows;
and, in paragraph (b), remove the words ``The A.S.T.M. standards may be
purchased from the American Society for Testing Materials, 1916 Race
Street, Philadelphia, Pa., 19103'' and add, in their place, the words
``You may purchase the standards of ASTM from the American Society for
Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA
19428-2959'':
Sec. 160.035-1 Applicable specifications.
(a) * * *
(1) Standards of ASTM:
ASTM A 36/A 36M-97a, Standard Specification for Carbon Structural
Steel--160.035-3
ASTM A 653/A 653M-98, Standard Specification for Steel Sheet, Zinc-
Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the
Hot-Dip Process--160.035-3
* * * * *
106. Revise Sec. 160.035-3(b)(1) to read as follows:
Sec. 160.035-3 Construction of steel oar-propelled lifeboats.
* * * * *
(b) Materials. (1) Plating for shell, floors, air tanks, etc., must
be in accordance with ASTM A 653, Coating Designation G90 (incorporated
by reference, see Sec. 160.035-1). The bend test required by these
specifications must be made after the galvanizing or other
anticorrosive treatment has been applied.
* * * * *
107. Revise Sec. 160.055-1(a)(4) to read as follows:
Sec. 160.055-1 Applicable specifications.
(a) * * *
(4) Standards of ASTM:
ASTM D 413-82 (1993), Standard Test Methods for Rubber Property--
Adhesion to Flexible Substrate--160.055-3
ASTM D 570-95, Standard Test Method for Water Absorption of Plastics--
160.055-3
ASTM D 882-97, Standard Test Method for Tensile Properties of Thin
Plastic Sheeting--160.055-3
ASTM D 1004-94a, Standard Test Method for Initial Tear Resistance of
Plastic Film and Sheeting--160.055-3
* * * * *
108. In Sec. 160.076-11(b), revise the entry for ``American Society
for Testing and Materials'' to read as follows:
Sec. 160.076-11 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM D 751-95, Standard Test Methods for Coated Fabrics--160.076-25
ASTM D 1434-82 (1988), Standard Test Method for Determining Gas
Permeability Characteristics of Plastic Film and Sheeting--160.076-25
* * * * *
109. In Sec. 160.077-5(b), revise the entry for ``American Society
for Testing and Materials'' to read as follows:
Sec. 160.077-5 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM B 117-97, Standard Practice for Operating Salt Spray (Fog)
Apparatus--160.077-11
ASTM D 751-95, Standard Test Methods for Coated Fabrics--160.077-19
ASTM D 1434-82 (1988), Standard Test Method for Determining Gas
Permeability Characteristics of Plastic Film and Sheeting--160.077-19
* * * * *
110. In Sec. 160.151-5(b), revise the entry for ``American Society
for Testing and Materials'' to read as follows:
Sec. 160.151-5 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM F 1014-92, Standard Specification for Flashlights on Vessels--
160.151-21
* * * * *
111. In Sec. 160.171-3(b), revise the entry for ``American Society
for Testing and Materials'' to read as follows:
Sec. 160.171-3 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM B 117-97, Standard Practice for Operating Salt Spray (Fog)
Apparatus--160.171-17
ASTM C 177-85 (1993), Standard Test Method for Steady-State Heat Flux
Measurements and Thermal Transmission Properties by Means of the
Guarded-Hot-Plate Apparatus--160.171-17
ASTM C 518-91, Standard Test Method for Steady-State Heat Flux
Measurements and Thermal Transmission Properties by Means of the Heat
Flow Meter Apparatus--160.171-17
ASTM D 975-98, Standard Specification for Diesel Fuel Oils--160.171-17
ASTM D 1004-94a, Standard Test Method for Initial Tear Resistance of
Plastic Film and Sheeting--160.171-17
* * * * *
112. In Sec. 160.174-3(b), revise the entry for ``American Society
for Testing and Materials'' to read as follows:
Sec. 160.174-3 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM C 177-85 (1993), Standard Test Method for Steady-State Heat Flux
Measurements and Thermal Transmission Properties by Means of the
Guarded-Hot-Plate Apparatus--160.174-17
ASTM C 518-91, Standard Test Method for Steady-State Heat Flux
Measurements and Thermal Transmission Properties by Means of the Heat
Flow Meter Apparatus--160.174-17
ASTM D 975-98, Standard Specification for Diesel Fuel Oils--160.174-17
ASTM D 1004-94a, Standard Test Method for Initial Tear Resistance of
Plastic Film and Sheeting--160.174-17
ASTM D 1518-85 (1990), Standard Test Method for Thermal Transmittance
of Textile Materials--160.174-17
* * * * *
113. In Sec. 160.176-4(b), revise the entry for ``American Society
for Testing and Materials'' to read as follows:
Sec. 160.176-4 Incorporation by reference.
* * * * *
[[Page 67185]]
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM B 117-97, Standard Practice for Operating Salt Spray (Fog)
Apparatus--160.176-8; 160.176-13
ASTM D 751-95, Standard Test Methods for Coated Fabrics--160.176-13
ASTM D 975-98, Standard Specification for Diesel Fuel Oils--160.176-13
ASTM D 1434-82 (1988), Standard Test Method for Determining Gas
Permeability Characteristics of Plastic Film and Sheeting--160.176-13
* * * * *
PART 161--ELECTRICAL EQUIPMENT
114. The authority citation for part 161 continues to read as
follows:
Authority: 46 U.S.C. 3306, 3703, 4302; E.O. 12234, 45 FR 58801,
3 CFR, 1980 Comp., p. 277; 49 CFR 1.46.
115. In Sec. 161.002-1(b), revise the entry for ``American Society
for Testing and Materials'' to read as follows:
Sec. 161.002-1 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM B 117-97, Standard Practice for Operating Salt Spray (Fog)
Apparatus--161.002-4
* * * * *
116. In Sec. 161.006-1, revise paragraph (a)(3) to read as follows:
Sec. 161.00 6-1 [Amended]
(a) * * *
* * * * *
(3) Standards of ASTM:
ASTM B 117-97, Standard Practice for Operating Salt Spray (Fog)
Apparatus--161.006-5
ASTM B 456-95, Standard Specification for Electrodeposited Coatings of
Copper Plus Nickel Plus Chromium and Nickel Plus Chromium--161.006-4
You may obtain these standards from The American Society for
Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA
19428-2959.
* * * * *
Sec. 161.006-4 [Amended]
117. In Sec. 161.006-4(h), remove the words ``A.S.T.M.
Specification B141-45, Type K.C., or as otherwise approved'' and add,
in their place, the words ``ASTM B 456 (incorporated by reference, see
Sec. 161.006-1), Service Condition 1, or as otherwise approved''.
Sec. 161.006-5 [Amended]
118. In Sec. 161.006-5(b)(3), remove the words ``A.S.T.M. Standard
B117-44T'' and add, in their place, the words ``ASTM B 117
(incorporated by reference, see Sec. 161.006-1)''.
PART 162--ENGINEERING EQUIPMENT
119. Revise the authority citation for part 162 to read as follows:
Authority: 33 U.S.C. 1321(j), 1903; 46 U.S.C. 3306, 3703, 4104,
4302; E.O. 12234, 45 FR 58801, 3 CFR, 1980 Comp., p. 277; E.O.
11735, 38 FR 21243, 3 CFR, 1971-1975 Comp., p. 793; 49 CFR 1.46.
Sec. 162.027-1 [Amended]
120. In 162.027-1(b), remove the words ``ASTM F 1546-94'' and add,
in their place, the words ``ASTM F 1546 [or] F 1546 M-96''.
Sec. 162.027-2 [Amended]
121. In Sec. 162.027-2, remove the words ``ASTM F 1546-94''
wherever they appear and add, in their place, the words ``ASTM F 1546
(incorporated by reference, see Sec. 162.027-1)''.
Sec. 162.027-3 [Amended]
122. In 162.027-3(a), remove the words ``ASTM F 1546-94'' and add,
in their place, the words ``ASTM F 1546 (incorporated by reference, see
Sec. 162.027-1)''.
123. In 162.050-4, revise paragraphs (a)(3) and (b)(2) to read as
follows:
Sec. 162.050-4 Documents incorporated by reference.
(a) * * *
(3) ASTM D 2777-98, Standard Practice for Determination of
Precision and Bias of Applicable Test Methods of Committee D-19 on
Water--162.050-15.
(b) * * *
(2) You may obtain the ASTM Standard from the American Society for
Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA
19428-2959.
* * * * *
Sec. 162.050-15 [Amended]
124. In 162.050-15(f)(1), remove the words ``the method described
in paragraph 10.3.2 of'' and the number ``D-2777-77'', and add, in
place of the latter, the number ``D 2777 (incorporated by reference,
see Sec. 162.050-4)''.
PART 163--CONSTRUCTION
125. The authority citation for part 163 continues to read as
follows:
Authority: 46 U.S.C. 3306, 3703, 5115; E.O. 12234, 45 FR 58801,
3 CFR, 1980 Comp., p. 277; 49 CFR 1.46.
126. Revise Sec. 163.003-3 to read as follows:
Sec. 163.003-3 ASTM standard.
The following standard of the American Society for Testing and
Materials (ASTM) is incorporated by reference into this subpart: ASTM D
1435-94, Standard Practice for Outdoor Weathering of Plastics. You may
obtain this standard from the Society at 100 Barr Harbor Drive, West
Conshohocken, PA 19428-2959.
PART 164--MATERIALS
127. The authority citation for part 164 continues to read as
follows:
Authority: 46 U.S.C. 3306, 3703, 4302; E.O. 12234, 45 FR 58801,
3 CFR, 1980 Comp., p. 277; 49 CFR 1.46.
128. Revise Sec. 164.007-1(b) to read as follows:
Sec. 164.007-1 Applicable specification and referenced material.
* * * * *
(b) Guidance. For guidance you may use the following technical
reference: ASTM E 119-98, Standard Test Methods for Fire Tests of
Building Construction and Materials. You may obtain it from The
American Society for Testing and Materials, 100 Barr Harbor Drive, West
Conshohocken, PA 19428-2959.
* * * * *
129. Revise Sec. 164.008-1(b) to read as follows:
Sec. 164.008-1 Applicable specification and referenced material.
* * * * *
(b) Guidance. For guidance you may use the following technical
reference: ASTM E 119-98, Standard Test Methods for Fire Tests of
Building Construction and Materials. You may obtain it from the
American Society for Testing and Materials, 100 Barr Harbor Drive, West
Conshohocken, PA 19428-2959.
* * * * *
Sec. 164.012-1 [Amended]
130. In 164.012-1, in paragraph (a)(1), remove the words ``E 84-
50T--Tentative Method of Fire Hazard Classification for Building
Materials'' and add, in their place, the words ``E 84-98, Standard Test
Method for Surface Burning Characteristics of
[[Page 67186]]
Building Materials''; and, in paragraph (b), remove the words ``1916
Race Street, Philadelphia, Pa., 19103'' and add, in their place, the
words ``100 Barr Harbor Drive, West Conshohocken, PA 19428-2959''.
131. In 164.015-1, revise paragraph (a)(4) to read as set forth
below and, in paragraph (b)(3), remove the words ``1916 Race Street,
Philadelphia, Pa. 19103'' and add, in their place, the words ``100 Barr
Harbor Drive, West Conshohocken, PA 19428-2959''.
PART 170--STABILITY REQUIREMENTS FOR ALL INSPECTED VESSELS
Sec. 164.015-1 Applicable Specifications and Standards.
(a) * * *
(4) ASTM D 4986-98, Standard Test Method for Horizontal Burning
Characteristics of Cellular Polymeric Materials.
* * * * *
132. The authority citation for part 170 continues to read as
follows:
Authority: 43 U.S.C. 1333; 46 U.S.C. 2103, 3306, 3703; E.O.
12234, 45 FR 58801, 3 CFR, 1980 Comp., p. 277; 49 CFR 1.46.
133. In Sec. 170.015(b), revise the entry for American Society for
Testing and Materials'' to read as follows:
Sec. 170.015 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM F 1196-94, Standard Specification for Sliding Watertight Door
Assemblies--170.270
ASTM F 1197-89 (1994), Standard Specification for Sliding Watertight
Door Control Systems--170.270
* * * * *
PART 174--SPECIAL RULES PERTAINING TO SPECIFIC VESSEL TYPES
134. The authority citation for part 174 continues to read as
follows:
Authority: 42 U.S.C. 9118, 9119, 9153; 43 U.S.C. 1333; 46 U.S.C.
3306, 3703, 5115; E.O. 12234, 45 FR 58801, 3 CFR, 1980 Comp., p.
277; 49 CFR 1.46.
135. In Sec. 174.007(b), revise the entry for ``American Society
for Testing and Materials'' to read as follows:
Sec. 174.007 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM F 1196-94, Standard Specification for Sliding Watertight Door
Assemblies--174.100
ASTM F 1197-89 (1994), Standard Specification for Sliding Watertight
Door Control Systems--174.100
PART 175--GENERAL PROVISIONS
136. The authority citation for part 175 continues to read as
follows:
Authority: 46 U.S.C. 2103, 3205, 3306, 3703; 49 U.S.C. App.
1804; 49 CFR 1.45, 1.46; 175.900 also issued under authority of 44
U.S.C. 3507.
137. In Sec. 175.600(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 175.600 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM B 96-93, Standard Specification for Copper-Silicon Alloy Plate,
Sheet, Strip, and Rolled Bar for General Purposes and Pressure
Vessels--182.440
ASTM B 117-97, Standard Practice for Operating Salt Spray (Fog)
Apparatus--175.400
ASTM B 122/B 122M-95, Standard Specification for Copper-Nickel-Tin
Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel
Alloy Plate, Sheet, Strip and Rolled Bar--182.440
ASTM B 127-98, Standard Specification for Nickel-Copper Alloy (UNS
NO4400) Plate, Sheet, and Strip--182.440
ASTM B 152-97a, Standard Specification for Copper Sheet, Strip, Plate,
and Rolled Bar--182.440
ASTM B 209-96, Standard Specification for Aluminum and Aluminum-Alloy
Sheet and Plate--182.440
ASTM D 93-97, Standard Test Methods for Flash Point by Pensky-Martens
Closed Cup Tester--175.400
ASTM D 635-97, Standard test Method for Rate of Burning and or Extent
and Time of Burning of Self-Supporting Plastics in a Horizontal
Position--182.440
ASTM D 2863-95, Standard Method for Measuring the Minimum Oxygen
Concentration to Support Candle-Like Combustion of Plastics (Oxygen
Index)--182.440
ASTM E 84-98, Standard Test Method for Surface Burning Characteristics
of Building Materials--177.410
* * * * *
PART 182--MACHINERY INSTALLATION
138. The authority citation for part 182 continues to read as
follows:
Authority: 46 U.S.C. 3306; E.O. 12234, 45 FR 58801, 3 CFR, 1980
Comp., p. 277; 49 CFR 1.46.
Sec. 182.440 [Amended]
139. In Sec. 182.440(a)(1), in Table 182.440(A)(1), in the heading
of column two, immediately following the words ``(latest edition)'' add
the words ``[see also Sec. 175.600 of this chapter]''; and in column
two, remove the words ``B97, alloys A, B, and C'' and add, in their
place, the words ``B 96, alloys C65100 and C65500''.
PART 190--CONSTRUCTION AND ARRANGEMENT
140. The authority citation for part 190 continues to read as
follows:
Authority: 46 U.S.C. 2113, 3306; E.O. 12234, 45 FR 58801, 3 CFR,
1980 Comp., p. 277; 49 CFR 1.46.
Sec. 190.01-3 [Removed]
141. Remove Sec. 190.01-3.
PART 193--FIRE PROTECTION EQUIPMENT
142. The authority citation for part 193 continues to read as
follows:
Authority: 46 U.S.C. 2213, 3102, 3306; E.O. 12234, 45 FR 58801,
3 CFR, 1980 Comp., p. 277; 49 CFR 1.46.
143. In Sec. 193.01-3(b), revise the entry for ``American Society
for Testing and Materials'' to read as follows:
Sec. 193.01-3 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM F 1121-87 (1993), Standard Specification for International Shore
Connections for Marine Fire Applications--193.10-10
* * * * *
PART 195--VESSEL CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT
144. The authority citation for part 195 continues to read as
follows:
[[Page 67187]]
Authority: 46 U.S.C. 2113, 3306; 49 U.S.C. App. 1804; E.O.
12234, 45 FR 58801, 3 CFR, 1980 Comp., p. 277; 49 CFR 1.46.
145. In Sec. 195.01-3(b), revise the entry for ``American Society
For Testing and Materials'' to read as follows:
Sec. 195.01-3 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM F 1014-92, Standard Specification for Flashlights on Vessels--
195.35-5
* * * * *
Sec. 195.35-5 [Amended]
146. In 195.35-5(c), remove the words ``ASTM F1014-1986'' and add,
in their place, the words ``ASTM F 1014 (incorporated by reference, see
Sec. 195.01-3)''.
PART 199--LIFESAVING SYSTEMS FOR CERTAIN INSPECTED VESSELS
147. The authority citation for part 199 continues to read as
follows:
Authority: 46 U.S.C. 3306, 3703; 46 CFR 1.46.
148. In Sec. 199.05(b), revise the entry for ``American Society for
Testing and Materials'' to read as follows:
Sec. 199.05 Incorporation by reference.
* * * * *
(b) * * *
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM D 93-97, Standard Test Methods for Flash Point by Pensky-Martens
Closed Cup Tester--199.261; 199.290
ASTM F 1003-86(1992), Standard Specification for Searchlights on Motor
Lifeboats--199.175
ASTM F 1014-92, Standard Specification for Flashlights on Vessels--
199.175
* * * * *
Sec. 199.261 [Amended]
149. In 199.261(g), remove the words ``ASTM D93-94'' and add, in
their place, the words ``ASTM D 93 (incorporated by reference, see
Sec. 199.05)''.
Sec. 199.290 [Amended]
150. In 199.290(b), remove the words ``ASTM D93-94'' and add, in
their place, the words ``ASTM D 93 (incorporated by reference, see
Sec. 199.05)''.
Dated: October 26, 1999.
T.H. Gilmour,
Captain, U.S. Coast Guard, Acting Assistant Commandant for Marine
Safety and Environmental Protection.
[FR Doc. 99-28611 Filed 11-30-99; 8:45 am]
BILLING CODE 4910-15-U