[Federal Register Volume 64, Number 208 (Thursday, October 28, 1999)]
[Notices]
[Pages 58125-58126]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 99-28099]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

National Highway Traffic Safety Administration

[Docket No. NHTSA-99-6383]


Notice of Receipt of Petition for Decision That Nonconforming 
1998 Jaguar XK-8 Passenger Cars Are Eligible for Importation

AGENCY: National Highway Traffic Safety Administration, DOT.

ACTION: Notice of receipt of petition for decision that nonconforming 
1998 Jaguar XK-8 passenger cars are eligible for importation.

-----------------------------------------------------------------------

SUMMARY: This document announces receipt by the National Highway 
Traffic Safety Administration (NHTSA) of a petition for a decision that 
a 1998 Jaguar XK-8 passenger car that was not originally manufactured 
to comply with all applicable Federal motor vehicle safety standards is 
eligible for importation into the United States because (1) It is 
substantially similar to a vehicle that was originally manufactured for 
importation into and sale in the United States and that was certified 
by its manufacturer as complying with the safety standards, and (2) It 
is capable of being readily altered to conform to the standards.

DATES: The closing date for comments on the petition is November 29, 
1999.

ADDRESSES: Comments should refer to the docket number and notice 
number, and be submitted to: Docket Management, Room PL-401, 400 
Seventh St., SW., Washington, DC 20590. [Docket hours are from 9 am to 
5 pm].

FOR FURTHER INFORMATION CONTACT: George Entwistle, Office of Vehicle 
Safety Compliance, NHTSA (202-366-5306).

SUPPLEMENTARY INFORMATION:

Background

    Under 49 U.S.C. 30141(a)(1)(A), a motor vehicle that was not 
originally manufactured to conform to all applicable Federal motor 
vehicle safety standards shall be refused admission into the United 
States unless NHTSA has decided that the motor vehicle is substantially 
similar to a motor vehicle originally manufactured for importation into 
and sale in the United States, certified under 49 U.S.C. 30115, and of 
the same model year as the model of the motor vehicle to be compared, 
and is capable of being readily altered to conform to all applicable 
Federal motor vehicle safety standards.
    Petitions for eligibility decisions may be submitted by either 
manufacturers or importers who have registered with NHTSA pursuant to 
49 CFR part 592. As specified in 49 CFR 593.7, NHTSA publishes notice 
in the Federal Register of each petition that it receives, and affords 
interested persons an opportunity to comment on the petition. At the 
close of the comment period, NHTSA decides, on the basis of the 
petition and any comments that it has received, whether the vehicle is 
eligible for importation. The agency then publishes this decision in 
the Federal Register.
    Champagne Imports of Lansdale, Pennsylvania (``Champagne'') 
(Registered Importer 90-009) has petitioned NHTSA to decide whether a 
1998 Jaguar XK-8 passenger car is eligible for importation into the 
United States. The vehicle which Champagne believes is substantially 
similar is the 1998 Jaguar XK-8 passenger car that was manufactured for 
importation into, and sale in, the United States and certified by its 
manufacturer as conforming to all applicable Federal motor vehicle 
safety standards.
    The petitioner claims that it carefully compared the non-U.S. 
certified 1998 Jaguar XK-8 to its U.S.-certified counterpart, and found 
the two vehicles to be substantially similar with respect to compliance 
with most Federal motor vehicle safety standards.
    Champagne submitted information with its petition intended to 
demonstrate that the non-U.S. certified 1998 Jaguar XK-8, as originally 
manufactured, conforms to many Federal motor vehicle safety standards

[[Page 58126]]

in the same manner as its U.S. certified counterpart, or is capable of 
being readily altered to conform to those standards.
    Specifically, the petitioner claims that the non-U.S. certified 
1998 Jaguar XK-8 is identical to its U.S. certified counterpart with 
respect to compliance with Standard Nos. 102 Transmission Shift Lever 
Sequence * * *, 103 Defrosting and Defogging Systems, 104 Windshield 
Wiping and Washing Systems, 105 Hydraulic Brake Systems, 106 Brake 
Hoses, 109 New Pneumatic Tires, 113 Hood Latch Systems, 116 Brake 
Fluid, 124 Accelerator Control Systems, 201 Occupant Protection in 
Interior Impact, 202 Head Restraints, 204 Steering Control Rearward 
Displacement, 205 Glazing Materials, 206 Door Locks and Door Retention 
Components, 207 Seating Systems, 209 Seat Belt Assemblies, 210 Seat 
Belt Assembly Anchorages, 212 Windshield Retention, 216 Roof Crush 
Resistance, 219 Windshield Zone Intrusion, and 302 Flammability of 
Interior Materials.
    Additionally, the petitioner states that the vehicle conforms to 
the Bumper Standard found at 49 CFR part 581.
    Petitioner also contends that the vehicle is capable of being 
readily altered to meet the following standards, in the manner 
indicated:
    Standard No. 101 Controls and Displays: (a) Substitution of a lens 
marked ``Brake'' for a lens with a noncomplying symbol on the brake 
failure indicator lamp; (b) Installation of a seat belt warning lamp 
that displays the appropriate symbol; (c) Recalibration of the 
speedometer/odometer to show distance in miles and speed in miles per 
hour.
    Standard No. 108 Lamps, Reflective Devices and Associated 
Equipment: (a) Installation of U.S.-model headlamp assemblies; (b) 
Installation of U.S.-model front and rear sidemarker/reflector 
assemblies; (c) Installation of U.S.-model taillamp assemblies; (d) 
Installation of a high mounted stop lamp if the vehicle is not already 
so equipped.
    Standard No. 110 Tire Selection and Rims: Installation of a tire 
information placard.
    Standard No. 111 Rearview Mirror: Replacement of the passenger side 
rearview mirror with a U.S.-model component.
    Standard No. 114 Theft Protection: Installation of a warning buzzer 
and a warning buzzer microswitch in the steering lock assembly.
    Standard No. 118 Power Window Systems: Rewiring of the power window 
system so that the window transport is inoperative when the ignition is 
switched off.
    Standard No. 208 Occupant Crash Protection: (a) Installation of a 
U.S.-model seat belt in the driver's position, or a belt webbing 
actuated microswitch inside the driver's seat belt retractor; (b) 
Installation of an ignition switch actuated seat belt warning lamp and 
buzzer; (c) Replacement of the driver's and passenger's side air bags 
and knee bolsters with U.S.-model components on vehicles that are not 
already so equipped. The petitioner states that the vehicle is equipped 
with combination lap and shoulder belts that adjust by means of an 
automatic retractor and release by means of a single push button at the 
front outboard seating positions, with combination lap and shoulder 
restraints that release by means of a single push button at the rear 
outboard seating positions, and with a lap belt in the rear center 
designated seating position.
    Standard No. 214 Side Impact Protection: Installation of 
reinforcing door beams.
    Standard No. 301 Fuel System Integrity: Installation of a rollover 
valve in the fuel tank vent line.
    The petitioner also states that all vehicles will be inspected 
prior to importation to ensure that they are equipped with anti-theft 
devices in compliance with the Theft Prevention Standard found in 49 
CFR part 541 and modified if necessary.
    The petitioner also states that a vehicle identification plate must 
be affixed to the vehicle to meet the requirements of 49 CFR part 565.
    Interested persons are invited to submit comments on the petition 
described above. Comments should refer to the docket number and be 
submitted to: Docket Management, Room PL-401, 400 Seventh St., SW, 
Washington, DC 20590. [Docket hours are from 9 am to 5 pm]. It is 
requested but not required that 10 copies be submitted.
    All comments received before the close of business on the closing 
date indicated above will be considered, and will be available for 
examination in the docket at the above address both before and after 
that date. To the extent possible, comments filed after the closing 
date will also be considered. Notice of final action on the petition 
will be published in the Federal Register pursuant to the authority 
indicated below.

    Authority: 49 U.S.C. 30141(a)(1)(A) and (b)(1); 49 CFR 593.8; 
delegations of authority at 49 CFR 1.50 and 501.8.

    Issued on October 22, 1999.
Marilynne Jacobs,
Director, Office of Vehicle Safety Compliance.
[FR Doc. 99-28099 Filed 10-27-99; 8:45 am]
BILLING CODE 4910-59-P