[Federal Register Volume 64, Number 74 (Monday, April 19, 1999)]
[Notices]
[Pages 19212-19214]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 99-9708]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

National Highway Traffic Safety Administration
[Docket No. NHTSA-99-5403]


Notice of Receipt of Petition for Decision that Nonconforming 
1998 and 1999 Lexus RX300 Multi-Purpose Passenger Vehicles Are Eligible 
for Importation

AGENCY: National Highway Traffic Safety Administration, DOT.

ACTION: Notice of receipt of petition for decision that nonconforming 
1998 and 1999 Lexus RX300 multi-purpose passenger vehicles (MPVs) are 
eligible for importation.

-----------------------------------------------------------------------

SUMMARY: This notice announces receipt by the National Highway Traffic 
Safety Administration (NHTSA) of a petition for a decision that 1998 
and 1999 Lexus RX300 MPVs that were not originally

[[Page 19213]]

manufactured to comply with all applicable Federal motor vehicle safety 
standards are eligible for importation into the United States because 
(1) they are substantially similar to vehicles that were originally 
manufactured for sale in the United States and that were certified by 
their manufacturer as complying with the safety standards, and (2) they 
are capable of being readily altered to conform to the standards.

DATES: The closing date for comments on the petition is May 19, 1999.

ADDRESSES: Comments should refer to the docket number and notice 
number, and be submitted to: Docket Management, Room PL-401, 400 
Seventh St., SW, Washington, DC 20590. [Docket hours are from 9 am to 5 
pm].

FOR FURTHER INFORMATION CONTACT: George Entwistle, Office of Vehicle 
Safety Compliance, NHTSA (202-366-5306).

SUPPLEMENTARY INFORMATION:

Background

    Under 49 U.S.C. 30141(a)(1)(A), a motor vehicle that was not 
originally manufactured to conform to all applicable Federal motor 
vehicle safety standards shall be refused admission into the United 
States unless NHTSA has decided that the motor vehicle is substantially 
similar to a motor vehicle originally manufactured for importation into 
and sale in the United States, certified under 49 U.S.C. 30115, and of 
the same model year as the model of the motor vehicle to be compared, 
and is capable of being readily altered to conform to all applicable 
Federal motor vehicle safety standards.
    Petitions for eligibility decisions may be submitted by either 
manufacturers or importers who have registered with NHTSA pursuant to 
49 CFR part 592. As specified in 49 CFR 593.7, NHTSA publishes notice 
in the Federal Register of each petition that it receives, and affords 
interested persons an opportunity to comment on the petition. At the 
close of the comment period, NHTSA decides, on the basis of the 
petition and any comments that it has received, whether the vehicle is 
eligible for importation. The agency then publishes this decision in 
the Federal Register.
    Champagne Imports, Inc. of Lansdale, Pennsylvania (``Champagne'') 
(Registered Importer 90-009) has petitioned NHTSA to decide whether 
1998 and 1999 Lexus RX300 MPVs that were not originally manufactured to 
comply with all applicable Federal motor vehicle safety standards are 
eligible for importation into the United States. The vehicles which 
Champagne believes are substantially similar are 1998 and 1999 Lexus 
RX300 MPVs that were manufactured for sale in the United States and 
certified by their manufacturer, Toyota Motor Corporation, as 
conforming to all applicable Federal motor vehicle safety standards.
    The petitioner claims that it carefully compared the non-U.S. 
certified 1998 and 1999 Lexus RX300 MPVs to their U.S. certified 
counterparts, and found the vehicles to be substantially similar with 
respect to compliance with most Federal motor vehicle safety standards.
    Champagne submitted information with its petition intended to 
demonstrate that the non-U.S. certified 1998 and 1999 Lexus RX300 MPVs, 
as originally manufactured, conform to many Federal motor vehicle 
safety standards in the same manner as their U.S. certified 
counterparts, or are capable of being readily altered to conform to 
those standards.
    Specifically, the petitioner claims that the non-U.S. certified 
1998 and 1999 Lexus RX300 MPVs are identical to their U.S. certified 
counterparts with respect to compliance with Standards Nos. 102 
Transmission Shift Lever Sequence * * *, 103 Defrosting and Defogging 
Systems, 104 Windshield Wiping and Washing Systems, 105 Hydraulic Brake 
Systems, 106 Brake Hoses, 113 Hood Latch Systems, 116 Brake Fluid, 119 
New Pneumatic Tires for Vehicles other than Passenger Cars, 124 
Accelerator Control Systems, 201 Occupant Protection in Interior 
Impact, 204 Steering Control Rearward Displacement, 205 Glazing 
Materials, 207 Seating Systems, 209 Seat Belt Assemblies, 210 Seat Belt 
Assembly Anchorages, 212 Windshield Retention, 219 Windshield Zone 
Intrusion, and 302 Flammability of Interior Materials.
    Petitioner also contends that the vehicles are capable of being 
readily altered to meet the following standards, in the manner 
indicated:
    Standard No. 101 Controls and Displays: (a) Substitution of a lens 
marked ``Brake'' for a lens with a noncomplying symbol on the brake 
failure indicator lamp; (b) installation of a seat belt warning lamp 
that displays the appropriate symbol; (c) recalibration of the 
speedometer/odometer from kilometers to miles per hour.
    Standard No. 108 Lamps, Reflective Devices and Associated 
Equipment: (a) Installation of U.S.-model headlamp assemblies that 
incorporate headlamps with DOT markings; (b) installation of U.S.-model 
front and rear sidemarker/reflector assemblies; (c) installation of 
U.S.-model taillamp assemblies; (d) installation of a center high 
mounted stop lamp on vehicles that are not already so equipped.
    Standard No. 111 Rearview Mirror: Replacement of the passenger side 
rearview mirror with a U.S.-model component.
    Standard No. 114 Theft Protection: Installation of a warning buzzer 
microswitch in the steering lock assembly and a warning buzzer.
    Standard No. 118 Power Window Systems: Rewiring of the power window 
system so that the window transport is inoperative when the ignition is 
switched off.
    Standard No. 120 Tire Selection and Rims for Motor Vehicles other 
than Passenger Cars: Installation of a tire information placard.
    Standard No. 206 Door Locks and Door Retention Components: 
Replacement of the rear door locks and rear door locking buttons.
    Standard No. 208 Occupant Crash Protection: (a) Installation of a 
U.S.-model seat belt in the driver's position, or a belt webbing-
actuated microswitch inside the driver's seat belt retractor; (b) 
installation of an ignition switch-actuated seat belt warning lamp and 
buzzer; (c) replacement of the driver's and passenger's side air bags 
and knee bolsters with U.S.-model components on vehicles that are not 
already so equipped. The petitioner states that the vehicles are 
equipped with combination lap and shoulder restraints that adjust by 
means of an automatic retractor and release by means of a single push 
button at both front designated seating positions, with combination lap 
and shoulder restraints that release by means of a single push button 
at both rear outboard designated seating positions, and with a lap belt 
in the rear center designated seating position.
    Standard No. 301 Fuel System Integrity: Installation of a rollover 
valve in the fuel tank vent line between the fuel tank and the 
evaporative emissions collection canister.
    The petitioner also states that a vehicle identification number 
plate must be affixed to the vehicles to meet the requirements of 49 
CFR part 565.
    Interested persons are invited to submit comments on the petition 
described above. Comments should refer to the docket number and be 
submitted to: Docket Management, Room PL-401, 400 Seventh St., SW, 
Washington, DC 20590. [Docket hours are from 9 am to 5 pm]. It is 
requested but not required that 10 copies be submitted.
    All comments received before the close of business on the closing 
date indicated above will be considered, and will be available for 
examination in the

[[Page 19214]]

docket at the above address both before and after that date. To the 
extent possible, comments filed after the closing date will also be 
considered. Notice of final action on the petition will be published in 
the Federal Register pursuant to the authority indicated below.

    Authority: 49 U.S.C. 30141(a)(1)(A) and (b)(1); 49 CFR 593.8; 
delegations of authority at 49 CFR 1.50 and 501.8.

    Issued on: April 13, 1999.
Marilynne Jacobs,
Director, Office of Vehicle Safety Compliance.
[FR Doc. 99-9708 Filed 4-16-99; 8:45 am]
BILLING CODE 4910-59-P