[Federal Register Volume 64, Number 53 (Friday, March 19, 1999)]
[Proposed Rules]
[Pages 13530-13531]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 99-6716]


 ========================================================================
 Proposed Rules
                                                 Federal Register
 ________________________________________________________________________
 
 This section of the FEDERAL REGISTER contains notices to the public of 
 the proposed issuance of rules and regulations. The purpose of these 
 notices is to give interested persons an opportunity to participate in 
 the rule making prior to the adoption of the final rules.
 
 ========================================================================
 

  Federal Register / Vol. 64, No. 53 / Friday, March 19, 1999 / 
Proposed Rules  

[[Page 13530]]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. 99-CE-01-AD]
RIN 2120-AA64


Airworthiness Directives; The New Piper Aircraft, Inc. Model PA-
46-350P Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: This document proposes to adopt a new airworthiness directive 
(AD) that would apply to certain The New Piper Aircraft, Inc. (Piper) 
Model PA-46-350P airplanes. The proposed AD would require installing 
reinforcement plates to the wing forward and aft attach fittings. The 
proposed AD is the result of a report that sheet steel material that is 
below design strength standards could be utilized on the wing attach 
fittings on the Model PA-46-350P airplanes manufactured since January 
1995. The actions specified by the proposed AD are intended to prevent 
structural failure of the wing attach fittings caused by the 
utilization of substandard material, which could result in the wing 
separating from the airplane with consequent loss of control.

DATES: Comments must be received on or before May 28, 1999.

ADDRESSES: Submit comments in triplicate to the Federal Aviation 
Administration (FAA), Central Region, Office of the Regional Counsel, 
Attention: Rules Docket No. 99-CE-01-AD, Room 1558, 601 E. 12th Street, 
Kansas City, Missouri 64106. Comments may be inspected at this location 
between 8 a.m. and 4 p.m., Monday through Friday, holidays excepted.
    Service information that applies to the proposed AD may be obtained 
from The New Piper Aircraft, Inc., Customer Services, 2926 Piper Drive, 
Vero Beach, Florida 32960. This information also may be examined at the 
Rules Docket at the address above.

FOR FURTHER INFORMATION CONTACT: Mr. William O. Herderich, Aerospace 
Engineer, FAA, Atlanta Aircraft Certification Office, One Crown Center, 
1895 Phoenix Boulevard, suite 450, Atlanta, Georgia 30349; telephone: 
(770) 703-6084; facsimile: (770) 703-6097.

SUPPLEMENTARY INFORMATION:

Comments Invited

    Interested persons are invited to participate in the making of the 
proposed rule by submitting such written data, views, or arguments as 
they may desire. Communications should identify the Rules Docket number 
and be submitted in triplicate to the address specified above. All 
communications received on or before the closing date for comments, 
specified above, will be considered before taking action on the 
proposed rule. The proposals contained in this notice may be changed in 
light of the comments received.
    Comments are specifically invited on the overall regulatory, 
economic, environmental, and energy aspects of the proposed rule. All 
comments submitted will be available, both before and after the closing 
date for comments, in the Rules Docket for examination by interested 
persons. A report that summarizes each FAA-public contact concerned 
with the substance of this proposal will be filed in the Rules Docket.
    Commenters wishing the FAA to acknowledge receipt of their comments 
submitted in response to this notice must submit a self-addressed, 
stamped postcard on which the following statement is made: ``Comments 
to Docket No. 99-CE-01-AD.'' The postcard will be date stamped and 
returned to the commenter.

Availability of NPRMs

    Any person may obtain a copy of this NPRM by submitting a request 
to the FAA, Central Region, Office of the Regional Counsel, Attention: 
Rules Docket No. 99-CE-01-AD, Room 1558, 601 E. 12th Street, Kansas 
City, Missouri 64106.

Discussion

    Piper has reported to the FAA a potential structural defect on 
certain Model PA-46-350P airplanes. The report was made based on 
Piper's obligation under section 21.3 of the Federal Aviation 
Regulations (14 CFR 21.3). This report indicates that sheet steel 
material that is below design strength standards could be utilized on 
the wing attach fittings on the Model PA-46-350P airplanes manufactured 
since January 1995.
    Piper discovered the condition during development testing in which 
premature yielding of the sheet steel material occurred. After sending 
samples of the material to a lab for analysis, Piper learned that the 
sheet steel was subjected to an annealing process instead of a 
normalizing process. The design requirements of the wing forward and 
aft attach fittings are for the sheet steel to be normalized instead of 
annealed.
    Piper received the annealed sheet steel material in early 1995. 
Those Model PA-46-350P airplanes that were manufactured since January 
1995 could utilize the annealed sheet steel wing attach fittings. The 
airplanes that were delivered since January 1995 incorporate serial 
numbers 4622191 through 4622200 and 4636001 through 4636175.
    This condition, if not corrected, could lead to failure of the wing 
attach fittings caused by utilization of substandard material, which 
could result in the wing separating from the airplane with consequent 
loss of control.

Relevant Service Information

    Piper has issued Service Bulletin No. 1027, dated November 19, 
1998, which specifies installing reinforcement plates to the wing 
forward and aft attach fittings by incorporating the Wing to Fuselage 
Reinforcement Installation Kit, Piper part number 766-656. This kit 
includes all the materials and procedures for accomplishing this 
installation.

The FAA's Determination

    After examining the circumstances and reviewing all available 
information related to the incidents described above, the FAA has 
determined that AD action should be taken to eliminate the unsafe 
condition previously referenced.

Explanation of the Provisions of the Proposed AD

    Since an unsafe condition has been identified that is likely to 
exist or

[[Page 13531]]

develop in other Piper Model PA-46-350P airplanes of the same type 
design manufactured since January 1995, the FAA is proposing AD action. 
The proposed AD would require installing reinforcement plates to the 
wing forward and aft attach fittings by incorporating the Wing to 
Fuselage Reinforcement Installation Kit, Piper part number 766-656. 
Accomplishment of the proposed installation would be required in 
accordance with the instructions to the above-referenced kit, as 
referenced in Piper Service Bulletin No. 1027, dated November 19, 1998.

Cost Impact

    The FAA estimates that 185 airplanes in the U.S. registry would be 
affected by the proposed AD, that it would take approximately 30 
workhours per airplane to accomplish the proposed installation, and 
that the average labor rate is approximately $60 an hour. Piper will 
give warranty credit for parts on all affected aircraft. Based on these 
figures, the total cost impact of the proposed AD on U.S. operators is 
estimated to be $333,000, or $1,800 per airplane.
    Piper has informed the FAA that parts have been distributed to 
accomplish the installation on 6 of the affected airplanes. Presuming 
that these parts were incorporated on 6 of the affected airplanes, this 
would reduce the cost impact of this AD by $10,800 from $333,000 to 
$322,200.

Regulatory Impact

    The regulations proposed herein would not have substantial direct 
effects on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government. Therefore, in 
accordance with Executive Order 12612, it is determined that this 
proposal would not have sufficient federalism implications to warrant 
the preparation of a Federalism Assessment.
    For the reasons discussed above, I certify that this action (1) is 
not a ``significant regulatory action'' under Executive Order 12866; 
(2) is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979); and (3) if promulgated, 
will not have a significant economic impact, positive or negative, on a 
substantial number of small entities under the criteria of the 
Regulatory Flexibility Act. A copy of the draft regulatory evaluation 
prepared for this action has been placed in the Rules Docket. A copy of 
it may be obtained by contacting the Rules Docket at the location 
provided under the caption ADDRESSES.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

    Accordingly, pursuant to the authority delegated to me by the 
Administrator, the Federal Aviation Administration proposes to amend 
part 39 of the Federal Aviation Regulations (14 CFR part 39) as 
follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec. 39.13  [Amended]

    2. Section 39.13 is amended by adding a new airworthiness directive 
(AD) to read as follows:

The New Piper Aircraft, Inc.: Docket No. 99-CE-01-AD.

    Applicability: Model PA-46-350P airplanes, serial numbers 
4622191 through 4622200 and 4636001 through 4636175, certificated in 
any category.

    Note 1: The affected serial numbers refer to airplanes that have 
been delivered since January 1995 and could have insufficient 
strength wing attach fittings installed. Airplanes manufactured 
after serial number 4636175 have this problem corrected prior to 
delivery.
    Note 2: This AD applies to each airplane identified in the 
preceding applicability provision, regardless of whether it has been 
modified, altered, or repaired in the area subject to the 
requirements of this AD. For airplanes that have been modified, 
altered, or repaired so that the performance of the requirements of 
this AD is affected, the owner/operator must request approval for an 
alternative method of compliance in accordance with paragraph (c) of 
this AD. The request should include an assessment of the effect of 
the modification, alteration, or repair on the unsafe condition 
addressed by this AD; and, if the unsafe condition has not been 
eliminated, the request should include specific proposed actions to 
address it.

    Compliance: Required within the next 100 hours time-in-service 
(TIS) after the effective date of this AD, unless already 
accomplished.
    To prevent the potential for failure of the wing attach fittings 
caused by the utilization of substandard material, which could 
result in the wing separating from the airplane with consequent loss 
of control of the airplane, accomplish the following:
    (a) Install reinforcement plates to the wing forward and aft 
attach fittings by incorporating the Wing to Fuselage Reinforcement 
Installation Kit, Piper part number 766-656. Accomplishment of the 
installation would be required in accordance with the instructions 
to the above-referenced kit, as referenced in Piper Service Bulletin 
No. 1027, dated November 19, 1998.
    (b) Special flight permits may be issued in accordance with 
sections 21.197 and 21.199 of the Federal Aviation Regulations (14 
CFR 21.197 and 21.199) to operate the airplane to a location where 
the requirements of this AD can be accomplished.
    (c) An alternative method of compliance or adjustment of the 
compliance time that provides an equivalent level of safety may be 
approved by the Manager, FAA, Atlanta Aircraft Certification Office 
(ACO), One Crown Center, 1895 Phoenix Boulevard, suite 450, Atlanta, 
Georgia 30349. The request shall be forwarded through an appropriate 
FAA Maintenance Inspector, who may add comments and then send it to 
the Manager, Atlanta ACO.

    Note 3: Information concerning the existence of approved 
alternative methods of compliance with this AD, if any, may be 
obtained from the Atlanta ACO.

    (d) All persons affected by this directive may obtain copies of 
the document referred to herein upon request to The New Piper 
Aircraft, Inc., Customer Services, 2926 Piper Drive, Vero Beach, 
Florida 32960; or may examine this document at the FAA, Central 
Region, Office of the Regional Counsel, Room 1558, 601 E. 12th 
Street, Kansas City, Missouri 64106.

    Issued in Kansas City, Missouri, on March 11, 1999.
Marvin R. Nuss,
Acting Manager, Small Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 99-6716 Filed 3-18-99; 8:45 am]
BILLING CODE 4910-13-P