[Federal Register Volume 63, Number 178 (Tuesday, September 15, 1998)] [Rules and Regulations] [Pages 49280-49281] From the Federal Register Online via the Government Publishing Office [www.gpo.gov] [FR Doc No: 98-24407] ----------------------------------------------------------------------- DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. 98-NM-159-AD; Amendment 39-10756; AD 98-19-16] RIN 2120-AA64 Airworthiness Directives; Aerospatiale Model ATR72-212A Series Airplanes AGENCY: Federal Aviation Administration, DOT. ACTION: Final rule. ----------------------------------------------------------------------- SUMMARY: This amendment adopts a new airworthiness directive (AD), applicable to certain Aerospatiale Model ATR72-212A series airplanes, that requires installation of bushings on the lower attachment fittings of the flap support beam. This amendment is prompted by issuance of mandatory continuing airworthiness information by a foreign civil airworthiness authority. The actions specified by this AD are intended to prevent rupture of the lower attachment fittings of the flap support beam due to fatigue, and consequent damage to the flaps; these conditions could result in reduced controllability of the airplane. DATES: Effective October 20, 1998. The incorporation by reference of certain publications listed in the regulations is approved by the Director of the Federal Register as of October 20, 1998. ADDRESSES: The service information referenced in this AD may be obtained from Aerospatiale, 316 Route de Bayonne, 31060 Toulouse, Cedex 03, France. This information may be examined at the Federal Aviation Administration (FAA), Transport Airplane Directorate, Rules Docket, 1601 Lind Avenue, SW., Renton, Washington; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC. FOR FURTHER INFORMATION CONTACT: Norman B. Martenson, Manager, International Branch, ANM-116, FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 227-2110; fax (425) 227-1149. SUPPLEMENTARY INFORMATION: A proposal to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) to include an airworthiness directive (AD) that is applicable to certain Aerospatiale Model ATR72- 212A series airplanes was published in the Federal Register on July 23, 1998 (63 FR 39538). That action proposed to require installation of bushings on the lower attachment fittings of the flap support beam. Comments Interested persons have been afforded an opportunity to participate in the making of this amendment. No comments were submitted in response to the proposal or the FAA's determination of the cost to the public. Conclusion The FAA has determined that air safety and the public interest require the adoption of the rule as proposed. Cost Impact The FAA estimates that 4 airplanes of U.S. registry will be affected by this AD, that it will take approximately 25 work hours per airplane to accomplish the [[Page 49281]] required installation, and that the average labor rate is $60 per work hour. Required parts will be provided by the manufacturer at no cost to the operators. Based on these figures, the cost impact of the installation required by this AD on U.S. operators is estimated to be $6,000, or $1,500 per airplane. The cost impact figure discussed above is based on assumptions that no operator has yet accomplished any of the requirements of this AD action, and that no operator would accomplish those actions in the future if this AD were not adopted. Regulatory Impact The regulations adopted herein will not have substantial direct effects on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, in accordance with Executive Order 12612, it is determined that this final rule does not have sufficient federalism implications to warrant the preparation of a Federalism Assessment. For the reasons discussed above, I certify that this action (1) is not a ``significant regulatory action'' under Executive Order 12866; (2) is not a ``significant rule'' under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A final evaluation has been prepared for this action and it is contained in the Rules Docket. A copy of it may be obtained from the Rules Docket at the location provided under the caption ADDRESSES. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. Adoption of the Amendment Accordingly, pursuant to the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows: PART 39--AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. Sec. 39.13 [Amended] 2. Section 39.13 is amended by adding the following new airworthiness directive: 98-19-16 Aerospatiale: Amendment 39-10756. Docket 98-NM-159-AD. Applicability: Model ATR72-212A series airplanes, on which Aerospatiale Modification 4831 has not been accomplished; certificated in any category. Note 1: This AD applies to each airplane identified in the preceding applicability provision, regardless of whether it has been otherwise modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance in accordance with paragraph (b) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it. Compliance: Required as indicated, unless accomplished previously. To prevent rupture of the lower attachment fittings of the flap support beam due to fatigue, and consequent damage to the flaps, accomplish the following: (a) Prior to the accumulation of 24,000 total flight cycles, or within 500 flight cycles after the effective date of this AD, whichever occurs later, install bushings on the lower attachment fittings of the flap support beam in accordance with Avions de Transport Regional Service Bulletin ATR72-57-1020, dated March 9, 1998. (b) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Manager, International Branch, ANM-116, FAA, Transport Airplane Directorate. Operators shall submit their requests through an appropriate FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, International Branch, ANM-116. Note 2: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the International Branch, ANM-116. (c) Special flight permits may be issued in accordance with sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the airplane to a location where the requirements of this AD can be accomplished. (d) The installation shall be done in accordance with Avions de Transport Regional Service Bulletin ATR72-57-1020, dated March 9, 1998. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from Aerospatiale, 316 Route de Bayonne, 31060 Toulouse, Cedex 03, France. Copies may be inspected at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC. Note 3: The subject of this AD is addressed in French airworthiness directive 98-072-036(B), dated February 11, 1998, as revised by Erratum 98-072-036(B), dated February 25, 1998. (e) This amendment becomes effective on October 20, 1998. Issued in Renton, Washington, on September 4, 1998. Darrell M. Pederson, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 98-24407 Filed 9-14-98; 8:45 am] BILLING CODE 4910-13-U