[Federal Register Volume 62, Number 159 (Monday, August 18, 1997)]
[Proposed Rules]
[Pages 43956-43958]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 97-21787]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. 97-CE-34-AD]
RIN 2120-AA64


Airworthiness Directives; Aerospace Technologies of Australia Pty 
Ltd. (Formerly Government Aircraft Factory) Models N22B, N22S, and N24A 
Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: This document proposes to adopt a new airworthiness directive 
(AD) that would apply to Aerospace Technologies of Australia Pty Ltd. 
(ASTA) Models N22B, N22S, and N24A airplanes. The proposed action would 
require repetitively inspecting the aft wing break connectors for 
arcing damage, deposits between contacts, and looseness of contacts; 
and removing deposits between contacts, tightening any loose contacts, 
and replacing any aft wing break connectors with arcing damage. The 
proposed AD results from several reports of uncommanded flap extensions 
and displays of incorrect stall warning indications on the affected 
airplanes. The actions specified by the proposed AD are intended to 
prevent contamination in the aft wing break connectors, which could 
result in uncommanded flap extensions and incorrect stall warning 
indications with consequent loss of airplane control.

DATES: Comments must be received on or before October 17, 1997.

ADDRESSES: Submit comments in triplicate to the Federal Aviation 
Administration (FAA), Central Region, Office of the Assistant Chief 
Counsel, Attention: Rules Docket No. 97-CE-34-AD, Room 1558, 601 E. 
12th Street, Kansas City, Missouri 64106. Comments may be inspected at 
this location between 8 a.m. and 4 p.m., Monday through Friday, 
holidays excepted.
    Service information that applies to the proposed AD may be obtained 
from Aerospace Technologies of Australia Pty Ltd., ASTA DEFENCE, 
Private Bag No. 4, Beach Road Lara 3212, Victoria, Australia. This 
information also may be examined at the Rules Docket at the address 
above.

FOR FURTHER INFORMATION CONTACT: Mr. Ron Atmur, Aerospace Engineer, 
FAA, Los Angeles Aircraft Certification Office, 3960 Paramount 
Boulevard, Lakewood, California 90712; telephone (562) 627-5224; 
facsimile (562) 627-5210.

SUPPLEMENTARY INFORMATION:

Comments Invited

    Interested persons are invited to participate in the making of the 
proposed rule by submitting such written data, views, or arguments as 
they may desire. Communications should identify the Rules Docket number 
and be submitted in triplicate to the address specified above. All 
communications received on or before the closing date for comments, 
specified above, will be considered before taking action on the 
proposed rule. The proposals contained in this notice may be changed in 
light of the comments received.
    Comments are specifically invited on the overall regulatory, 
economic, environmental, and energy aspects of the proposed rule. All 
comments submitted will be available, both before and after the closing 
date for comments, in the Rules Docket for examination by interested 
persons. A report that summarizes each FAA-public contact concerned 
with the substance of this proposal will be filed in the Rules Docket.
    Commenters wishing the FAA to acknowledge receipt of their comments 
submitted in response to this notice must submit a self-addressed, 
stamped postcard on which the following statement is made: ``Comments 
to Docket No. 97-CE-34-AD.'' The postcard will be date stamped and 
returned to the commenter.

Availability of NPRMs

    Any person may obtain a copy of this NPRM by submitting a request 
to the FAA, Central Region, Office of the Assistant Chief Counsel, 
Attention: Rules Docket No. 97-CE-34-AD, Room 1558, 601 E. 12th Street, 
Kansas City, Missouri 64106.

Discussion

    The Civil Aviation Safety Authority (CASA), which is the 
airworthiness authority for Australia, recently notified the FAA that 
an unsafe condition may exist on certain ASTA Models N22B, N22S, and 
N24A airplanes. The CASA reports several uncommanded flap extensions 
and displays of incorrect stall warning indications on the referenced 
airplanes. Contamination in the aft wing break connectors can cause 
such occurrences. These conditions, if not detected and corrected, 
could lead to loss of airplane control.

[[Page 43957]]

Applicable Service Information

    ASTA has issued Nomad Service Bulletin (SB) ANMD-57-13, dated 
October 30, 1995. This SB includes procedures for inspecting the aft 
wing break connectors for arcing damage, deposits between contacts, and 
looseness of contacts; and removing deposits between contacts, 
tightening any loose contacts, and replacing any aft wing break 
connectors with arcing damage.
    The CASA of Australia classified this service bulletin as mandatory 
and issued FCAA AD/GAF-N22/74, dated March 1996, in order to assure the 
continued airworthiness of these airplanes in Australia.

The FAA's Determination

    This airplane model is manufactured in Australia and is type 
certificated for operation in the United States under the provisions of 
section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and 
the applicable bilateral airworthiness agreement. Pursuant to this 
bilateral airworthiness agreement, the CASA of Australia has kept the 
FAA informed of the situation described above. The FAA has examined the 
findings of the CASA of Australia; reviewed all available information, 
including the service information referenced above; and determined that 
AD action is necessary for products of this type design that are 
certificated for operation in the United States.

Explanation of the Provisions of the Proposed AD

    Since an unsafe condition has been identified that is likely to 
exist or develop in other ASTA Models N22B, N22S, and N24A airplanes of 
the same type design that are registered in the United States, the FAA 
is proposing AD action. The proposed AD would require repetitively 
inspecting the aft wing break connectors for arcing damage, deposits 
between contacts, and looseness of contacts; and removing deposits 
between contacts, tightening any loose contacts, and replacing any aft 
wing break connectors with arcing damage.
    Accomplishment of the proposed actions would be in accordance with 
Nomad SB ANMD-57-13, dated October 30, 1995.

Cost Impact

    The FAA estimates that 15 airplanes in the U.S. registry would be 
affected by the proposed AD, that it would take approximately 1 
workhour per airplane to accomplish the proposed initial inspection, 
and that the average labor rate is approximately $60 an hour. Based on 
these figures, the total cost impact of the proposed AD on U.S. 
operators is estimated to be $900 or $60 per airplane. This figure does 
not take into account the cost of repetitive inspections or the cost to 
replace any damaged aft wing break connectors. The FAA has no way of 
determining the number of repetitive inspections each operator would 
incur over the life of each affected airplane or the number of aft wing 
break connectors that may be found damaged during the inspections 
proposed by this action.

Regulatory Impact

    The regulations proposed herein would not have substantial direct 
effects on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government. Therefore, in 
accordance with Executive Order 12612, it is determined that this 
proposal would not have sufficient federalism implications to warrant 
the preparation of a Federalism Assessment.
    For the reasons discussed above, I certify that this action (1) is 
not a ``significant regulatory action'' under Executive Order 12866; 
(2) is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979); and (3) if promulgated, 
will not have a significant economic impact, positive or negative, on a 
substantial number of small entities under the criteria of the 
Regulatory Flexibility Act. A copy of the draft regulatory evaluation 
prepared for this action has been placed in the Rules Docket. A copy of 
it may be obtained by contacting the Rules Docket at the location 
provided under the caption ADDRESSES.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

    Accordingly, pursuant to the authority delegated to me by the 
Administrator, the Federal Aviation Administration proposes to amend 
part 39 of the Federal Aviation Regulations (14 CFR part 39) as 
follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec. 39.13  [Amended]

    2. Section 39.13 is amended by adding a new airworthiness directive 
(AD) to read as follows:

Aerospace Technologies of Australia PTY LTD: Docket No. 97-CE-34-AD.

    Applicability: Models N22B, N22S, and N24A airplanes (all serial 
numbers), certificated in any category.

    Note 1: This AD applies to each airplane identified in the 
preceding applicability provision, regardless of whether it has been 
modified, altered, or repaired in the area subject to the 
requirements of this AD. For airplanes that have been modified, 
altered, or repaired so that the performance of the requirements of 
this AD is affected, the owner/operator must request approval for an 
alternative method of compliance in accordance with paragraph (e) of 
this AD. The request should include an assessment of the effect of 
the modification, alteration, or repair on the unsafe condition 
addressed by this AD; and, if the unsafe condition has not been 
eliminated, the request should include specific proposed actions to 
address it.

    Compliance: Required as indicated in the body of this AD, unless 
already accomplished.
    To prevent contamination in the aft wing break connectors, which 
could result in uncommanded flap extensions and incorrect stall 
warning indications with consequent loss of airplane control, 
accomplish the following:
    (a) Within the next 100 hours time-in-service (TIS) after the 
effective date of this AD and thereafter at intervals not to exceed 
300 hours TIS, inspect the aft wing break connectors for arcing 
damage, deposits between contacts, and looseness of contacts. 
Accomplish these inspections in accordance with the ACCOMPLISHMENT 
INSTRUCTIONS section of Nomad Service Bulletin (SB) ANMD-57-13, 
dated October 30, 1995.
    (b) If any deposits between contacts, loose contacts, or aft 
wing break connector arcing damage is found, prior to further 
flight, accomplish the following, as applicable, in accordance with 
the ACCOMPLISHMENT INSTRUCTIONS section of Nomad SB ANMD-57-13, 
dated October 30, 1995:
    (1) Remove any deposits between contacts;
    (2) Tighten any loose contacts; and
    (3) Replace any aft wing break connectors with arcing damage.
    (c) The repetitive inspections specified in this AD are required 
even if deposit is removed between the aft wing break connector 
contacts; any aft wing break connector contacts are tightened; or 
any aft wing break connectors are replaced.
    (d) Special flight permits may be issued in accordance with 
sections 21.197 and 21.199 of the Federal Aviation Regulations (14 
CFR 21.197 and 21.199) to operate the airplane to a location where 
the requirements of this AD can be accomplished.
    (e) An alternative method of compliance or adjustment of the 
compliance time that provides an equivalent level of safety may be 
approved by the Manager, FAA, Los Angeles ACO, 3960 Paramount 
Boulevard., Lakewood, California 90712. The request

[[Page 43958]]

shall be forwarded through an appropriate FAA Maintenance Inspector, 
who may add comments and then send it to the Manager, Los Angeles 
ACO.

    Note 2: Information concerning the existence of approved 
alternative methods of compliance with this AD, if any, may be 
obtained from the Los Angeles ACO.

    (f) All persons affected by this directive may obtain copies of 
the document referred to herein upon request to Aerospace 
Technologies of Australia Pty Ltd., ASTA DEFENCE, Private Bag No. 4, 
Beach Road Lara 3212, Victoria, Australia; or may examine this 
document at the FAA, Central Region, Office of the Assistant Chief 
Counsel, Room 1558, 601 E. 12th Street, Kansas City, Missouri 64106.

    Issued in Kansas City, Missouri, on August 11, 1997.
Michael Gallagher,
Manager, Small Airplane Directorate, Aircraft Certification Service.
[FR Doc. 97-21787 Filed 8-15-97; 8:45 am]
BILLING CODE 4910-13-U