[Federal Register Volume 62, Number 87 (Tuesday, May 6, 1997)]
[Rules and Regulations]
[Pages 24690-24743]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 97-10481]
[[Page 24689]]
_______________________________________________________________________
Part II
Department of Transportation
_______________________________________________________________________
Research and Special Programs Administration
_______________________________________________________________________
49 CFR Part 171, et al.
Hazardous Materials: Harmonization With the United Nations
Recommendations, International Maritime Dangerous Goods Code, and
International Civil Aviation Organization's Technical Instructions;
Final Rule
Federal Register / Vol. 62, No. 87 / Tuesday, May 6, 1997 / Rules and
Regulations
[[Page 24690]]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Research and Special Programs Administration
49 CFR Parts 171, 172, 173, 175, 176, 178
[Docket No. HM-215B; Amdt Nos. 171-153, 172-154, 173-261, 175-86, 176-
43, 178-119]
RIN 2137-AC82
Hazardous Materials: Harmonization With the United Nations
Recommendations, International Maritime Dangerous Goods Code, and
International Civil Aviation Organization's Technical Instructions
AGENCY: Research and Special Programs Administration (RSPA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: This final rule amends the Hazardous Materials Regulations to
maintain alignment with corresponding provisions of international
standards. Because of recent changes to the International Maritime
Dangerous Goods Code (IMDG Code), the International Civil Aviation
Organization's Technical Instructions for the Safe Transport of
Dangerous Goods by Air (ICAO Technical Instructions), and the United
Nations Recommendations on the Transport of Dangerous Goods (UN
Recommendations), these revisions are necessary to facilitate the
transport of hazardous materials in international commerce.
DATES: Effective date: The effective date of these amendments is
October 1, 1997.
Compliance date: RSPA is authorizing immediate voluntary
compliance. However, persons voluntarily complying with these
regulations should be aware that petitions for reconsideration may be
received and, as a result of RSPA's evaluation of those petitions, the
amendments adopted in this final rule could be subject to further
revision.
Incorporation by reference. The incorporation by reference of
certain publications listed in these amendments has been approved by
the Director of the Federal Register as of October 1, 1997.
FOR FURTHER INFORMATION CONTACT: Bob Richard, Assistant International
Standards Coordinator, telephone (202) 366-0656, or Joan McIntyre,
Office of Hazardous Materials Standards, telephone (202) 366-8553,
Research and Special Programs Administration, U.S. Department of
Transportation, 400 Seventh Street, S.W., Washington, D.C. 20590-0001.
SUPPLEMENTARY INFORMATION:
I. Background
On December 21, 1990, the Research and Special Programs
Administration (RSPA) published a final rule [Docket HM-181; 55 FR
52402] which comprehensively revised the Hazardous Materials
Regulations (HMR), 49 CFR Parts 171 to 180, with respect to hazard
communication, classification, and packaging requirements, based on the
UN Recommendations. One intended effect of the rule was to facilitate
the international transportation of hazardous materials by ensuring a
basic consistency between the HMR and international regulations.
The UN Recommendations are not regulations, but are recommendations
issued `by the UN Committee of Experts on the Transport of Dangerous
Goods (UNCOE). These recommendations are amended and updated biennially
by the UNCOE and are distributed to nations throughout the world. They
serve as the basis for national, regional, and international modal
regulations (specifically the IMDG Code, issued by the International
Maritime Organization (IMO), and the ICAO Technical Instructions,
issued by the ICAO Dangerous Goods Panel). In 49 CFR 171.12, the HMR
authorize shipments prepared in accordance with the IMDG Code if all or
part of the transportation is by vessel, subject to certain conditions
and limitations. Offering, accepting and transporting hazardous
materials by aircraft, in conformance with the ICAO Technical
Instructions, and by motor vehicle either before or after being
transported by aircraft, are authorized in Sec. 171.11 (subject to
certain conditions and limitations).
On December 29, 1994, RSPA issued a final rule [Docket HM-215A; 59
FR 67390] amending the HMR by incorporating changes to more fully align
the HMR with the seventh and eighth revised editions of the UN
Recommendations, Amendment 27 to the IMDG Code and the 1995-96 ICAO
Technical Instructions. The final rule provided consistency with
international air and sea transportation requirements which became
effective January 1, 1995.
In a final rule published December 16, 1996, RSPA incorporated the
latest editions of the ICAO Technical Instructions and the IMDG Code
into the HMR to ensure that international shippers could begin
complying with changes to international air and vessel standards going
into effect on January 1, 1997. That final rule authorized compliance
with either Amendment 27 or Amendment 28 of the IMDG Code and either
the 1995-96 or 1997-98 ICAO Technical Instructions until June 1, 1997.
This final rule amends the HMR based on the ninth revised edition
of the UN Recommendations, the 1997-98 ICAO Technical Instructions, and
Amendment 28 to the IMDG Code. It is intended to more fully align the
HMR with international air and sea transport requirements which became
effective January 1, 1997. Other changes are based on feedback from the
regulated industry and RSPA initiatives.
II. Summary of Comments
RSPA received over 40 comments in response to the Docket HM-215B
Notice of Proposed Rulemaking (NPRM), which was published in the
Federal Register on October 25, 1996 (61 FR 55364). Comments were
submitted by chemical manufacturers, trade associations, packaging
manufacturers, and rail and vessel carriers. Commenters were supportive
of RSPA's efforts to maintain alignment with international standards.
Certain issues proposed in the NPRM received little or no comment.
Other issues, including a proposed definition for ``aerosol,'' a
proposed approval requirement for certain nitroglycerin mixtures, and
various proposed changes for organic peroxides and explosives
packagings, were the focus of most comments. Several commenters
requested transitional provisions and other amendments to the HMR as
part of this initiative. In this final rule, RSPA is providing a
delayed compliance period for implementation of these changes; however,
many other suggestions are beyond the scope of the proposed changes in
this rule and first should be the subject of an NPRM to offer adequate
opportunity for notice and comment.
III. Summary of Regulatory Changes by Section
Listed below is a section-by-section summary of changes and, as
applicable, a discussion of comments received.
Part 171
Section 171.7
RSPA proposed to add or update various American Society for Testing
and Materials (ASTM) standards, including an ASTM standard for flash
point determination (ASTM D-3828-93) which establishes whether a
material is capable of sustaining combustion in relation to classifying
flammable liquids (ASTM D-4206-96), and the ASTM standard for assessing
corrosivity to metals (ASTM G 31-72 (Reapproved 1995)). ASTM D-3828-93
is the Standard Test Method for Flash Point by
[[Page 24691]]
Small Scale Closed Tester. This method is equivalent to ASTM D-3278 but
specifically applies to testing petroleum products and lubricants. ASTM
D 4206-96 Standard Test Method for Sustained Burning of Liquid Mixtures
Using the Small Scale Open-Cup Apparatus is equivalent to the test
method currently provided in Part 173, Appendix H-Method of Testing for
Sustained Combustibility.
In addition, RSPA proposed to incorporate the most current versions
of the ICAO Technical Instructions, the IMDG Code, the UN
Recommendations and the UN Manual of Tests and Criteria. Updated
references for the IMDG Code and the ICAO Technical Instructions were
adopted in a final rule published December 16, 1996 [61 FR 65958] with
an effective date of June 1, 1997. Two references were proposed for
incorporation under the Transportation of Dangerous Goods (TDG)
Regulations issued by Transport Canada. These new entries reference
Schedule 21 and Schedule 22, which were adopted in 1995.
Section 171.8
In the NPRM, RSPA proposed several new definitions, including a
definition for ``Aerosol'' which is consistent with provisions of
Sec. 173.306(a)(3). As noted in the NPRM, the definition for aerosols
in the IMDG Code and the ICAO Technical Instructions includes
containers that are filled solely with a gas, whereas aerosol
containers authorized in Sec. 173.306(a)(3) may be charged with a gas
only for the purpose of expelling a liquid, powder or paste.
RSPA received two comments opposing the proposed definition of
``Aerosol''. Both commenters (a chemical manufacturing company and The
Chemical Specialties Manufacturers Association (CSMA)) believed the
definition in the HMR should be worded in the same manner as in the UN
Recommendations. These commenters also claimed that the proposed
definition may not cover foams, pastes, gels and other liquids which
are not ejected in suspension in a gas. CSMA further noted that the
proposed definition only recognizes metal aerosol containers while
international standards authorize glass and plastic as materials of
construction for aerosol containers.
RSPA's proposed definition for ``Aerosol'' corresponds to current
requirements for aerosols in Sec. 173.306(a)(3). Paragraph (a)(3)
contains an authorization for the use of metal nonspecification
packagings charged with a solution of materials and compressed gas or
gases (i.e., aerosols) with certain restrictions applying to internal
pressure, filling limits and testing of the container. The capacity of
this container cannot exceed 50 cubic inches or 27.7 fluid ounces.
These provisions apply only to solutions of materials and compressed
gas or gases which are not poisonous (other than Division 6.1, Packing
Group III materials). A final rule published October 28, 1991, under
Docket HM-210 [56 FR 55471], was issued for clarification and to
promote the safe transportation of gases shipped under limited quantity
provisions. This final rule stated, in part:
RSPA is concerned about the serious potential hazards posed by
shipping flammable compressed gases, under limited quantity or
consumer commodity provisions, when a compressed gas is the primary
product and not merely an aerosol propellant additive. RSPA and its
predecessor agencies never intended that gases other than those used
as a propellant could be excepted from any of the HMR when a package
has more than a 4-fluid ounce capacity.
Thus, current aerosol provisions in the HMR do not correspond to the
aerosol definition in international standards, which authorizes a gas
to be expelled ``without a liquid, paste, or powder.'' Nor does RSPA
intend to adopt such a provision, because filling a container solely
with a gas, such as butane, poses a significantly greater risk than
filling the container with a liquid, paste or powder which is expelled
by a butane gas due to greater quantities of gas contained in aerosols
that do not contain liquid, paste or powder. Furthermore, in response
to commenters' concern that the proposed definition may not cover
foams, pastes, gels and other liquids which are not ejected in
suspension in a gas, RSPA believes that because foams or gels would be
considered liquids expelled by a gas, it is not necessary to
specifically list them.
Another difference between domestic requirements for aerosols and
international standards is that the HMR authorize only metal
containers, while non-metallic (e.g., made from glass or plastic)
containers are authorized internationally. A November 13, 1995 response
to a petition for reconsideration issued under Docket HM-215A [60 FR
56957] emphasized that only metal aerosol containers are authorized for
use. This document noted that ``RSPA is not aware of any proposed
industry standards for the manufacture and use of aerosol containers
other than those made of metal.'' Nor is RSPA aware of any subsequent
ongoing action to propose industry standards for the manufacture and
use of non-metallic aerosol containers.
In addition, RSPA proposed corresponding changes in Secs. 171.11,
171.12 and 171.12a to clarify the proposed definition of aerosols as it
applies to aerosols imported in accordance with the ICAO Technical
Instructions, the IMDG Code and the TDG Regulations. These changes, as
well as the definition for aerosols, are adopted as proposed in this
final rule.
RSPA also proposed definitions for ``SADT'' (self-accelerating
decomposition temperature), salvage packagings and intermediate
packagings. No comments were received on these proposed definitions,
and they are adopted as proposed.
Sections 171.11, 171.12, and 171.12a
These sections authorize shipments prepared under the ICAO
Technical Instructions, the IMDG Code, and the TDG Regulations,
respectively. RSPA proposed to remove the requirement to include the
words ``Dangerous When Wet'' on shipping papers in association with the
basic description for Division 4.3 materials. Commenters uniformly
supported this proposal, stating that the change was compatible with
international standards and that the ``Dangerous When Wet'' hazard is
clearly communicated through indication of Division 4.3 as part of the
basic shipping description and through use of Division 4.3 labels and
placards. Therefore, RSPA is removing the requirement for ``Dangerous
When Wet'' to appear on shipping papers in association with the basic
description.
RSPA also proposed that the words ``Toxic Inhalation Hazard'' be
added as an alternative to ``Poison Inhalation Hazard'' or ``Inhalation
Hazard'' and that ``Toxic'' or ``Toxic Gas'' be added as alternatives
to ``Poison'' or ``Poison Gas''. A corresponding provision for shipping
paper descriptions was proposed for Sec. 172.203(m). Two comments
expressing opposing viewpoints were received. One commenter, an
international chemical and industrial gases manufacturer, supported
this proposal, stating that this alternative will simplify compliance
when shipping materials poisonous by inhalation. The other commenter, a
vessel carrier, believed consistency could be achieved through use of
only the ``Toxic'' designation. This commenter claimed that providing
an option for use of either term will confuse people in the field. RSPA
does not agree and is adopting the alternative ``Toxic Inhalation
Hazard'' as proposed in the NPRM. However, RSPA is not adopting
proposed modifications to
[[Page 24692]]
POISON and POISON GAS label and placard references. These references
were recently modified by the Docket HM-206 final rule [62 FR 1227] and
RSPA believes additional modifications to these references are
unnecessary.
Also, as discussed above for Sec. 171.8, RSPA is adopting a
provision to allow only aerosols meeting the definition of ``aerosol''
in Sec. 171.8 to be imported in accordance with the ICAO Technical
Instructions, IMDG Code and TDG regulations.
Section 171.14
A new paragraph (d) is added to provide a delayed implementation
date for amendments adopted in this final rule. The effective date of
this final rule is October 1, 1997. However, RSPA is authorizing an
immediate voluntary compliance date to allow shippers to prepare their
international shipments in accordance with the new ICAO, IMDG Code and
HMR provisions. RSPA is also authorizing a delayed mandatory compliance
with the new requirements, until October 1, 1998. This delay is
comparable to the transition provisions provided in the final rule
under Docket HM-215A and offers a sufficient phase-in period to
implement new provisions and deplete current stocks of shipping papers,
labels, placards, and containers affected by the new requirements. In
addition, paragraph (d)(2) permits intermixing of old and new hazard
communication requirements until October 1, 1998.
Part 172
Section 172.101
A new paragraph (c)(14) is added to allow isomers of materials
listed in the Hazardous Materials Table (HMT) which meet the same
hazard class, subsidiary risk and packing group to be identified using
the listed shipping description. One commenter suggested adding a
provision to exclude isomers listed specifically in the HMT. RSPA
agrees and is revising this paragraph to reflect the commenter's
suggestion.
A new paragraph (c)(15) is adopted to allow hydrates of inorganic
substances to be described using the proper shipping name for the
equivalent anhydrous material. In this final rule, RSPA is clarifying
the proposed regulatory text to indicate that the hydrate must meet the
same hazard class or division, subsidiary risk(s) and packing group of
the equivalent anhydrous material, unless the hydrate is specifically
identified in the Table.
Paragraph (f) is revised to acknowledge that Division 6.2 materials
(other than regulated medical waste) do not have packing group
assignments.
Changes to the HMT include:
New Packing Group I entries added for certain commodities,
including Adhesives, Resin solutions, Paint and Paint-related material,
Disinfectants, Dyes, and Oxidizing liquid, n.o.s.
An alternative proper shipping name ``Refrigerant gas'' plus the
``R'' number is added to numerous entries, consistent with the ninth
revised edition of the UN Recommendations. Current entries that contain
an italicized ``R'' number are revised to include the ``R'' number in
Roman type as part of the ``Refrigerant gas'' alternative proper
shipping name. One commenter engaged in reselling prepackaged
refrigerants expressed concern that some refrigerant manufacturers
would use the newly authorized ``Refrigerant gas, R ***'' proper
shipping name while others would continue to use the current chemical
name; consequently, a shipping paper description, package markings and
emergency response information may not match. This commenter
recommended that differences in proper shipping names resulting from
mixed use of the original and alternative proper shipping name on
markings, emergency response information and shipping papers be
authorized indefinitely, as long as the same UN or NA identification
number appears on the shipping paper, emergency response information,
and package markings. RSPA does not agree. The HMT contains numerous
entries providing an alternative proper shipping name. It is RSPA's
opinion that to offer various mix and match provisions for such entries
is impracticable and could result in greater confusion.
Certain Class 1 entries assigned NA numbers for domestic
transportation are removed. These include Explosive pest control
devices and Propellant explosives (both liquid and solid). Domestic
exceptions for these explosives are incorporated into the explosive
packing instructions, where applicable.
RSPA proposed a new entry and special provision for a nitroglycerin
mixture containing more than 2 percent but not more than 10 percent
nitroglycerin. The special provision sets forth a requirement that the
Associate Administrator for Hazardous Materials Safety (AAHMS) must
specifically authorize the nitroglycerin mixture as a Division 4.1
material, as well as approve the assigned packing group and packaging
method before the material may be transported as a Division 4.1
material. A chemical manufacturer and several pharmaceutical
manufacturers opposed this proposal. According to these commenters, a
preparation consisting of 10% nitroglycerin is used in the treatment of
acute angina attacks. They claimed that, unless this proposal is
dropped or the domestic supplier of this material is granted an
approval to ship the preparation as a Division 4.1 material,
transporting this material as a Division 1.1D explosive would have a
significant negative impact on the continued production and
distribution of this product.
RSPA does not agree. A certain preparation containing 10%
nitroglycerin was considered to be a UN 0143, 1.1D explosive by the
UNCOE in December 1994, based on the fact that the preparation
detonated in the bonfire test prescribed in test series 6(c) of the UN
Manual of Tests and Criteria. The UNCOE recognized that not all
preparations containing 10% nitroglycerin behave the same. Therefore,
the UNCOE adopted UN 3319 with a provision for each competent authority
to authorize, either by approval or exemption, a preparation consisting
of not more than 10% nitroglycerin as a Division 4.1 material based on
test results. This provision is consistent with the existing provisions
of Sec. 173.124(a)(1)(ii)(B) for desensitized explosive substances
which require authorization, either by approval or exemption, by the
AAHMS. RSPA believes that a 10% nitroglycerin preparation that will
detonate in a fire should be considered a forbidden material according
to Sec. 173.21(h). If the preparation is or may be explosive according
to Sec. 173.54(a), it is forbidden for transport unless examined and
approved under the provisions of Sec. 173.56. Depending on test
results, the same preparation may be approved under Sec. 173.56 as a
Division 4.1 material. RSPA does not believe the incorporation of UN
3319 with a lengthy transition period for shippers to obtain an
approval or exemption, where appropriate, would seriously threaten the
production of nitroglycerin pharmaceutical treatments in the United
States.
New entries are added for compressed gases and liquefied gases
which are toxic and also meet flammable, corrosive, or oxidizing
criteria.
Packaging authorizations for the current entry ``Gas, refrigerated
liquid'' are revised to reference the packaging provisions for
cryogenic liquids. In addition, two new entries ``Gas, refrigerated
liquid, flammable, n.o.s.'' and ``Gas, refrigerated liquid, oxidizing,
n.o.s.'' are added. One commenter supported the proposal to change
[[Page 24693]]
packaging authorizations for ``Gas, refrigerated liquid'' to reference
packagings for cryogenic liquids, but believed that packaging
exceptions provided in Sec. 173.320 should be authorized for ``Gas,
refrigerated liquid, n.o.s.'' and ``Gas, refrigerated liquid,
oxidizing, n.o.s.'' The commenter claimed that this section should
apply if the components of the mixture are exclusively various
combinations of atmospheric gases and/or helium in cryogenic liquid
form. RSPA agrees and is adding an exception in Column (8A) for these
two entries.
Several entries, such as Phenyl isocyanate and Phosphorous
trichloride, are amended by revising the primary hazard class in Column
(3) and/or Packing Group in Column (5). For some entries, such a change
in hazard class or packing group also results in a corresponding
removal of the ``+'' in Column (1).
In Column (2) of the HMT, several proper shipping names are listed
in Roman type, indicating that they are authorized proper shipping
names. However, they are not listed as proper shipping names under the
UN Recommendations, the ICAO Technical Instructions, or the IMDG Code.
For consistency with the international regulations, RSPA is revising a
number of proper shipping names, including ``Aircraft evacuation
slides'', from Roman type to italics to indicate that they are no
longer authorized proper shipping names.
Certain entries, such as Diphenylmethane-4,4'-diisocyanate and
Methyl benzoate (which do not meet toxicity criteria for a Division 6.1
Packing Group III material) are removed. These commodities were deleted
from the List of Dangerous Goods in the ninth revised edition of the UN
Recommendations.
The packing group designation for ``Mercury, contained in
manufactured articles'' is revised from Packing Group I to Packing
Group III for consistency with the entry for ``Mercury'' and the ICAO
Technical Instructions.
To maintain consistency with the UN Recommendations, various proper
shipping names are amended by the addition or removal of the word
``compressed'', ``inhibited'', ``liquefied'' or ``solution''. Several
commenters indicated that although they generally support the
international harmonization effort and overall intent to maintain
consistency between the HMR, the UN Recommendations, the IMDG Code, and
the ICAO Technical Instructions, they did not understand the basis for
the addition or deletion of the words ``compressed,'' ``inhibited,'' ``
liquefied'' or ``solution'' relative to clarifying certain existing
shipping names. These amendments were adopted by the UNCOE, in part, to
more effectively communicate the threat posed by certain materials in
their different physical states, e.g., pressurized materials that may
be transported as a liquid or as a gas. The description modifications
were supported by several large industry groups at the time the UNCOE
was considering the amendments.
RSPA recognizes that revising proper shipping names to include or
exclude these four modifiers to the key words identifying the hazardous
materials poses problems that makes compliance difficult in the one-
year period provided in Sec. 172.101(l)(1)(ii). Those difficulties and
the associated additional costs of compliance were highlighted in
comments provided by several shippers and carriers of industrial gases.
In consideration of those comments, RSPA is providing an exception in
Sec. 172.101(l)(3) that obviates the need for shippers and carriers to
make special arrangements to remark bulk or non-bulk packagings used in
the transportation of the affected hazardous materials within one year
following the effective date of this rule. Rather, when the proper
shipping name of a hazardous material is modified only by the addition
or omission of the word ``compressed,'' ``inhibited,'' `` liquefied''
or ``solution,'' its packaging may be marked with the previously
prescribed proper shipping name for that material for a period of five
years following the effective date of this rule. The extended
compliance period is intended to allow re-marking to be accomplished in
association with the periodic five-year retest required for most bulk
packagings.
To minimize the effects of other amendments, RSPA is incorporating
an extended transition period comparable to that provided in Docket HM-
215A. This will allow industry time to deplete current stocks of pre-
printed shipping papers, labels and packagings affected by the new
shipping names and to implement the changes within their respective
companies, including providing any necessary training to employees.
Two commenters pointed out a conflict in the proposed addition of a
Division 5.1 subsidiary risk label for the entry ``Carbon dioxide and
oxygen mixtures''. RSPA has stated previously that this subsidiary risk
should be recognized only when a mixture contains a concentration of
oxygen greater than 23.5%, requiring a subsidiary risk label for this
entry without regard to the amount of oxygen in the mixture is
inconsistent. Although the UN Recommendations prescribe a subsidiary
5.1 risk label without any distinctions, RSPA agrees with these
commenters. Therefore, a new Special Provision 77 is added to limit the
requirement for this subsidiary risk label to mixtures having an oxygen
concentration greater than 23.5% for domestic transportation. In
addition, RSPA intends to bring this inconsistency to the attention of
the UN Committee of Experts.
RSPA is adjusting quantity limits for certain materials identified
as poisonous by inhalation when transported by passenger or cargo
aircraft or passenger railcar. Many of these changes are consistent
with current quantity limits prescribed in the ICAO Technical
Instructions. Certain other materials are forbidden for transportation
by aircraft or passenger railcar because they have been identified as
meeting the criteria for poisonous by inhalation and assigned Hazard
Zone A for liquids and Hazard Zones A and B for gases.
Other changes to the HMT include: (1) Creating separate entries for
``Ammonia, anhydrous'' and ``Ammonia solutions''; (2) adding ``First
aid kits'' as an alternative proper shipping name for the entry
``Chemical kits'' if the first aid kits contain hazardous materials;
(3) combining entries for ``Chlorite solution'' and ``Hypochlorite
solutions''; (4) removing ``Methyl alcohol'' as an authorized proper
shipping name for ``Methanol'' but retaining it in italics as a cross
reference; (5) adding a Class 3 subsidiary risk in Column (6) for
several entries; and (6) creating a new entry for ``Aerosols (engine
starting fluid)'' to indicate that these aerosols are prohibited on
both passenger and cargo only aircraft.
RSPA is not incorporating various entries suggested by commenters
that were not proposed in the NPRM. As noted previously, these
suggestions are beyond the scope of the proposed changes in this rule
and should be subject to notice and comment.
Appendix B to Sec. 172.101
RSPA proposed to add, remove or revise a number of entries in the
HMR's List of Marine Pollutants. These changes are based on Amendment
27 (to the extent not already incorporated in HM-215A) and Amendment 28
of the IMDG Code. Currently, Appendix B contains a duplicate entry for
``Maneb or Maneb preparations''; however, one entry has supplemental
information in Roman type, while the supplemental information in the
other entry is shown in italics. RSPA proposed to remove the entry
listed in all Roman type. One
[[Page 24694]]
commenter indicated that the other entry should be retained for
consistency with the IMDG Code. The commenter is correct; RSPA is
retaining the entry ``Maneb or Maneb preparations with not less than 60
per cent maneb.'' In addition, several commenters suggested various
other revisions to the list and RSPA has amended the list accordingly.
Section 172.102
A new special provision 15 is added as proposed to prescribe
quantity limits and packaging for chemical kits and first aid kits.
Other special provisions are added to authorize reclassification for
certain commodities and to provide exceptions based on testing,
concentrations, or stabilization for materials such as Maneb, aqueous
solutions of inorganic solid nitrates, and Ferrocerium.
RSPA proposed to assign Special Provision 30 to the international
entry for ``Sulfur'' to indicate that this material is not subject to
the HMR when transported in a non-bulk packaging or if formed in a
specific shape. The Sulphur Institute strongly supported this change
and recommended rewording Special Provision 30 by removing the phrase
``when transported domestically''. RSPA agrees and this special
provision is revised accordingly.
One commenter suggested RSPA revise Special Provision 47 to
incorporate a special provision adopted in the ICAO Technical
Instructions which allows small packagings consisting of sealed packets
containing less than 10 ml of a Packing Group II or III flammable
liquid absorbed onto a solid material to be excepted from the HMR if no
free liquid is present in the packet. The commenter believed this
provision is consistent with a previous letter of opinion RSPA issued
concerning alcohol wipes and should be adopted as an ``A'' special
provision, at a minimum, for consistency with ICAO. RSPA agrees and is
incorporating this exception into Special Provision 47 to apply to all
modes of transport.
RSPA proposed to add a new special provision A25 to authorize
polyester resin kits in certain quantities to be packaged in non-
specification packagings for transportation by aircraft. One commenter
suggested removing this special provision, as well as Special Provision
40 (which currently is assigned to polyester resin kits), and
incorporating all packaging provisions for polyester resin kits in
Sec. 173.152. After further consideration, RSPA agrees and is adding
specific packaging provisions in Sec. 173.152 applicable to all modes
of transport for polyester resin kits.
In addition to revising the proper shipping name ``Aluminum
smelting by-products or Aluminum remelting by-products'' (formerly
Aluminum processing by-products), a new special provision B115 is
assigned to this entry to permit certain non-specification bulk
packagings for these products. Commenters representing the aluminum
industry responded favorably to this proposal. A commenter suggested
two modifications--one to add a new special provision applicable to
both non-bulk and bulk packaging to include certain materials which
exhibit corrosivity at PG II and III levels and the other to allow both
special provisions to apply to ``magnesium granules.'' RSPA is adding a
new Special Provision 128 and revising Sec. 172.101 Table entries for
UN 3096 and UN 3131 (Packing Groups II and III) to allow aluminum
smelting by-products and aluminum remelting by-products which are
described by a generic proper shipping name because they meet the
criteria for both Division 4.3 and Class 8, to be packaged in
accordance with Special Provision B115. However, RSPA is not expanding
this provision to include non-bulk packagings, nor will Magnesium
granules be assigned B115. In the NPRM, RSPA proposed a special
provision for aluminum by-products which would eliminate the need for
DOT Exemption DOT-E-11602. RSPA does not believe it appropriate at this
time to adopt, without public notice and comment, new provisions which
go beyond the relief authorized in DOT-E-11602 and proposed in the
NPRM.
Special Provision N50, which provides an exception from Class 9
labeling for marine pollutants that are not hazardous substances or
hazardous wastes, is removed. A corresponding change is made in Column
7 of the HMT to remove Special Provision N50 for the entries
``Environmentally hazardous substance, liquid (or solid) n.o.s.''
Section 172.203
RSPA is removing the requirement in paragraph (j) that the words
``Dangerous When Wet'' be annotated on shipping papers. As discussed
previously, RSPA believes that the ``Dangerous When Wet'' hazard is
adequately communicated through an indication of the Division 4.3
hazard class as part of the basic description on shipping papers.
Commenters uniformly supported this proposal and stated that the change
was compatible with international standards and that the ``Dangerous
When Wet'' hazard is clearly communicated through indication of
Division 4.3 as part of the basic shipping description, emergency
response information on the shipping paper, and use of Division 4.3
labels and placards.
The list of generic proper shipping names which require inclusion
of a technical name in paragraph (k)(3) is amended by adding several
entries for hydrocarbon gases, hydrocarbon gas mixtures, and
compressed, liquefied or refrigerated gases which have a subsidiary
hazard of oxidizer or flammability. In addition, RSPA is adding the
entry for ``Organometallic compound, water reactive, flammable,
n.o.s.'' which was inadvertently omitted in a previous rulemaking
action.
As discussed previously in Secs. 171.11, 171.12 and 171.12a, RSPA
is adding the word ``Toxic'' and the phrase ``Toxic-Inhalation Hazard''
in paragraph (m)(3) as an alternative to ``Poison''. RSPA proposed the
addition of a new paragraph (m)(4) to provide an exception from the
requirement to indicate on a shipping paper that a material is toxic if
the toxicity of the material is based solely on corrosive destruction
of tissue rather than systemic poisoning. One commenter believed this
exception should not apply to materials poisonous by inhalation, which
require additional shipping paper information to communicate the
presence of a fatal inhalation hazard. The commenter believed the
proposal was ill conceived and not beneficial to safety. After further
consideration, RSPA believes that this proposed exception may not be
appropriate for any material meeting toxicity criteria, not just a
toxic by inhalation hazard material. Therefore, proposed paragraph
(m)(4) is not adopted in this final rule.
Part 173
Section 173.3
Paragraph (c)(3) is amended to authorize the word ``SALVAGE'' as an
alternative marking for salvage drums. In addition, a new paragraph
(c)(7) is added to allow the use of salvage packagings which have been
certified and marked to UN standards. RSPA is not adopting other
marking requirements specified in the UN Recommendations such as: (1)
Adding the letter ``T'' in the package specification markings following
the package identification code (e.g. 1A2T/Y300/...); (2) annotating
the words ``SALVAGE PACKAGING'' after the basic description on the
shipping papers; and (3) adopting salvage packaging performance tests
requiring salvage packagings to be tested at the Packing Group II level
using liquid as the test medium. It is RSPA's view that
[[Page 24695]]
additional costs incurred by such marking and performance testing
requirements are not justified because salvage packaging provisions
currently prescribed in the HMR are adequate.
Two commenters addressed proposed changes to this section and both
supported RSPA's decision to retain current salvage packaging
provisions. For example, the Steel Shipping Container Institute
maintained that it could not support complete harmonization with
international salvage packaging standards until it has been clearly
determined that incidents of failure in salvage packagings meeting the
UN standards are less than those meeting current HMR requirements.
Section 173.21
The last sentence of paragraph (f) is amended to correctly
reference the UN Manual of Tests and Criteria.
Section 173.32c
Currently an IM portable tank or its compartment having a volume
greater than 5000 liters must have a minimum filling density of 80%.
RSPA proposed to increase the minimum tank or compartment size to 7500
liters, consistent with international standards. One commenter claimed
that RSPA's proposal did not go far enough and indicated that a filling
restriction on portable tanks used solely for domestic highway
transport is unjustified and precludes shippers from transporting
relatively small quantities of hazardous materials in portable tanks.
The commenter believed that a filling restriction of less than 80% for
IM portable tanks or compartments should not apply to transport by
highway. This commenter also stated that the purpose of the ``80%
rule'' was to preclude hydraulic surge that could make adequate
securing of portable tanks aboard vessels difficult and potentially
dangerous, but that surge is not a safety concern in highway transport.
RSPA disagrees that surge is not a safety concern in highway
transport of IM portable tanks. Portable tanks, when mounted on a
vehicle chassis, may have a higher center of gravity as compared to
standard cargo tank trucks. The effects of liquid movement and its
destabilizing effect at high speed and during abrupt turning can
contribute to roll-over. This effect is most predominant when ullage is
greater than 20%. Furthermore, it is RSPA's opinion that information
supplied by this commenter does not provide sufficient incentive for
RSPA to expand relief beyond that proposed in the NPRM. RSPA may
consider this matter further in future rulemaking action on the basis
of pertinent technical justification (e.g., data indicating forces
experienced during transport of portable tanks as a result of cargo
surge).
Section 173.34
Because of a printing error, in the table in paragraph (e)(18)(i),
for DOT 8 or 8AL cylinders used to transport acetylene, under ``Porous
filler requalification,'' the year ``2001'' is corrected to read
``2011'.
Section 173.60
As proposed, amendments to this section are consistent with the UN
Recommendations, are largely editorial and serve to streamline and
consolidate general requirements for packaging explosives while
eliminating redundant and unnecessary requirements. These amendments
are intended to more clearly convey general packaging requirements
applicable to packaging explosives for transportation and do not impose
new requirements.
RSPA received one comment from a company specializing in explosives
regulatory compliance. This commenter recommended adding a reference to
Sec. 173.24(e) at the end of Sec. 173.60(b)(8) and dropping proposed
(b)(8) because (b)(9) addresses compatibility. RSPA does not agree.
Section 173.60(b)(8) specifically addresses loose explosive substances
or the explosives substance of a uncased or partly cased article which
may present a sifting hazard from the package. However, RSPA believes
it may be useful to add the explanatory reference to Sec. 173.24(e) at
the end of Sec. 173.60(b)(9).
Section 173.62
RSPA proposed new explosives packaging methods in the Explosives
Table which were developed by the UNCOE, based on comments received
from the Department of Defense and explosive industry representatives,
and on competent authority approvals and exemptions issued to shippers
of explosives. These new methods are significantly more flexible than
the methods currently prescribed in the Explosives Table and
incorporate a broader range of options for authorized inner,
intermediate and outer packagings. In several instances, inner and
intermediate packagings are no longer required. Explosives Packing
Instructions are consistent with those adopted in the ICAO Technical
Instructions. In addition, many explosives (particularly those shipped
under not otherwise specified (n.o.s.) entries) which currently require
competent authority packaging approval are now assigned to specific
packing methods eliminating the requirement for the competent authority
to approve the packaging for these explosives.
A commenter asked RSPA to revise a provision for jet perforating
guns in proposed Packing Instruction US1 to allow a higher total
explosives content per tool pallet, based on a current exemption
authorizing this higher quantity of explosives. RSPA agrees and is
revising US1 to authorize up to 90.8 kg (200 pounds) total explosive
contents per pallet.
Another commenter, the Sporting Arms and Ammunition Manufacturers'
Institute (SAAMI), recommended several changes to the proposed
revisions. First, SAAMI believed the elimination of inner packaging
requirements for ``Cartridges, small arms'' (UN0012) is inconsistent
with Sec. 173.60 (b)(3) and (b)(5). RSPA does not agree. Only when
metal outer packagings are used for UN0012, would Sec. 173.60(b)(3)
require a means of prevention from contact with the cartridges. This
means could be padding or partitions and not necessarily an inner
packaging. These cartridges have their explosives substances enclosed
in an outer casing and do not require separation according to
Sec. 173.60(b)(3). RSPA believes the recessed primer well design of
most cartridges for weapons effectively protects the article from
accidental actuation. Shippers should add protection for articles that
present an actuation hazard according to Sec. 173.60(b)(5), but that
protection can be offered by means other than requiring an inner
packaging.
Secondly, SAAMI claimed that ``Small arms ammunition, ORM-D'' would
require more stringent packaging under Sec. 173.63(b)(2) than
``Cartridges, small arms'' classed as Division 1.4S and packaged in
accordance with Packing Instruction 130. RSPA believes that more
stringent packaging requirements for ORM-D materials (which are
excepted from most shipping paper, marking, labeling and placarding
provisions of the HMR) is appropriate. Furthermore, cartridges for
weapons must be clearly identified, marked and labeled as Division 1.4S
explosive articles.
SAAMI also claimed that packaging requirements for ``Cases,
cartridge, empty with primer'' (UN0055) are more stringent than for
``Cartridges, small arms'' (UN0012). RSPA believes the inner packaging
requirement for UN0055, primed cartridge cases, empty in Packing
Instruction 136 is appropriate. These cases have an exposed explosive
substance coated or deposited on the primer which could loosen and sift
out of the outer
[[Page 24696]]
packaging without the inner packaging requirement.
RSPA does not agree with SAAMI's contention that the wording in
Packing Instruction 133, regarding the authorization of trays as inner
packagings for certain explosives, is confusing. RSPA believes that
listing UN identification numbers for which the use of trays as inner
packagings is prohibited is clearer because nearly 50 percent fewer
numbers are listed.
Finally, SAAMI recommended that for ``Primers, cap type'' (UN0044),
D9 and D11 limitations assigned to current Packing Method E-142 should
be reinstated in Packing Instruction 133. RSPA does not agree. The
harmonization of the HMR to international performance-oriented
packaging requirements and with general packaging instructions for
explosives has resulted in the successful elimination of many explosive
quantity limitations per package. As a result, shipper compliance has
become easier to achieve without increased risk to the public.
Section 173.120
Paragraphs (a)(3) and (b)(3) are revised to include a reference to
ASTM D 4206 and a new paragraph (c)(1)(i)(C) is added to reference test
method ASTM D 3828.
Section 173.124
Amendments to the test methods for flammable solids, pyrophoric
materials, self heating substances and water reactive materials are
adopted as proposed. The Self-Reactive Materials Table is updated to
include seven new substances, consistent with the UN Recommendations.
In the ninth revised edition of the UN Recommendations, Figure 14.2
(Flow Chart for Self-Reactive Substances) was amended. Paragraph
(a)(2)(iv) of that chart is used to determine the generic type for a
self-reactive material.
Section 173.125
The criteria for classification and packing group assignment for
readily combustible materials of Division 4.1 is amended for
consistency with the UN Recommendations. A reference to Appendix E
(which is removed in this final rule) is replaced by references to the
UN Manual of Tests and Criteria.
In paragraph (b), the UN burning rate test and criteria for
classification is incorporated. The classification criteria for readily
combustible materials is amended to require powdered, granular and
pasty materials to be classified in Division 4.1 when the burning time
for one or more of the test runs, according to the UN burning rate test
method, is less than 45 seconds or the rate of burning is more than 2.2
mm/s. Powders of metal or metal alloys are classified in Division 4.1
when they can be ignited and the reaction spreads over the whole length
of the sample in 10 minutes or less.
Readily combustible solids are assigned to Packing Group II if the
burning time is less than 45 seconds and the flame passes the wetted
zone. Packing Group II is assigned to powders of metal or metal alloys
if the zone of reaction spreads over the whole length of the sample in
five minutes or less. Packing Group III is assigned if the burning time
is less than 45 seconds and the wetted zone stops the flame propagation
for at least four minutes. Packing Group III is assigned to metal
powders if the reaction spreads over the whole length of the sample in
more than five minutes but not more than ten minutes.
In paragraph (c), Packing Group II and III assignment criteria for
self-heating materials is revised to more accurately account for the
volume of material being transported. For instance, certain self-
heating materials which are packaged and transported in volumes less
than 3 cubic meters or in quantities less than 450 liters are not
subject to the requirements of the HMR.
In paragraph (d), the packing group assignment criteria is revised
for consistency with the UN Recommendations. These amendments do not
significantly affect the packing group assignment criteria, but are
purely editorial to clarify the meaning of ``spontaneous ignition.''
Section 173.127
RSPA is revising the definition for solid oxidizers and adding a
new definition, test and criteria for liquid oxidizers. Liquid
oxidizers would not be classified by analogy as currently required in
the HMR. The references to Appendix F (which is removed in this final
rule) are replaced by a reference to the UN Manual of Tests and
Criteria.
Paragraph (b)(1) is revised to include a statement indicating that
the material must be tested in the concentration offered for transport.
The criteria for packing group assignment is revised to specify the
ratios of solid oxidizing material and cellulose used in assessing the
burning characteristics for comparison with the burning characteristics
of potassium bromate, potassium perchlorate or potassium persulphate
and cellulose mixtures.
Paragraph (b)(2) incorporates packing group assignment criteria for
liquid oxidizers adopted in the ninth revised edition of the UN
Recommendations. Incorporating specific criteria for liquid oxidizers
provides a more precise means for shippers to classify these products
and eliminates ambiguity involved in classifying these materials by
analogy.
Section 173.128
In paragraph (c)(3) the reference to the UN Manual of Tests and
Criteria is revised to reflect its correct title. Paragraph (e) is
amended to update the reference to Figure 11.1 (Classification and
Flowchart Scheme for Organic Peroxides).
Section 173.132
A new paragraph (b)(3)(iii) is added to clarify when solid and
liquid materials are required to be tested for acute toxicity by
inhalation. One commenter recommended that RSPA remove the second
sentence in paragraph (b)(3) because proposed (b)(3)(iii) not only
addresses this issue but is more specific. RSPA does not agree. While
there is some overlap, current (b)(3) provides more details of testing
and new (b)(3)(iii) is more specific as to when tests must be run.
Current paragraph (c) is redesignated as paragraph (d), and a new
paragraph (c) is added to authorize three methods for use in
classifying and assigning packing groups to mixtures of materials
possessing oral and dermal toxicity characteristics. One commenter
pointed out that the formula in paragraph (c) is missing a ``+''
between the second and third fractions and also is missing a note found
in international standards. In this final rule, RSPA is inserting the
``+'' between the second and third fractions. RSPA intentionally did
not propose the additional note referenced by this commenter because
the note provides optional information rather than imposing a
regulatory requirement. However, for consistency with international
standards and convenience of the reader, RSPA is adding the note at the
end of paragraph (c).
Section 173.136
A new paragraph (c) is added to clarify that skin corrosion test
data developed prior to September 30, 1995, would continue to be valid.
This revision is based on a statement in the preamble to the HM-215A
final rule (December 29, 1994; 59 FR 67400) that RSPA would not require
retesting of materials classified under the previous test method in
Appendix A of Part 173.
Section 173.137
Paragraph (b) is revised to clarify that, when determining whether
a material
[[Page 24697]]
meets Class 8 Packing Group II, the material cannot meet Class 8
Packing Group I .
Section 173.152
Limited quantity provisions are added in paragraph (b)(4)(i) for
polyester resin kits for transport by all modes.
Section 173.162
A new sentence is added at the end of the paragraph to provide an
exception from the HMR for small quantities of gallium contained in
manufactured articles or apparatuses.
Section 173.166
This section is revised to remove all references to ``seat-belt
modules'', consistent with changes in the UN Recommendations. Packaging
provisions in paragraph (e) are revised to add drums, jerricans, and
plastic boxes to the array of authorized packagings. In addition to
non-specification containers currently authorized for transporting air
bags within a controlled distribution system, RSPA is also specifically
authorizing dedicated handling devices.
Section 173.185
This section is revised for consistency with changes adopted in the
ninth revised edition of the UN Recommendations and in the ICAO
Technical Instructions.
Currently there are different quantity limitations in the HMR for
determining whether lithium cells and batteries may be designated as
items of Class 9 on the basis of whether they meet the tests and
criteria provided in the UN Manual of Tests and Criteria. These
limitations also apply to lithium cells and batteries contained in
equipment. The limitations are based on whether the cells or batteries
will be transported on passenger or cargo aircraft. Consistent with the
ICAO Technical Instructions, RSPA is adopting an authorization to allow
cells containing not more than 12 grams of lithium or lithium alloy,
and batteries containing not more than 500 grams of lithium or lithium
alloy, to be designated as Class 9 when transported by passenger or
cargo aircraft. This also applies to lithium cells and batteries
contained in equipment under specified conditions.
RSPA is also expanding the types of packagings authorized for
transporting cells and batteries by aircraft to include an array of
boxes, drums and jerricans. Additionally, RSPA is eliminating the
requirement for equipment containing lithium cells and batteries to be
packaged in waterproof outer packaging if the equipment itself is
constructed to be waterproof (i.e., lifesaving equipment designed to
function in water).
One commenter indicated that his company's batteries would not pass
all the tests specified in the UN Tests and Criteria for lithium
batteries. RSPA believes the regulations as adopted provide an adequate
alternative for lithium battery manufacturers. Under Sec. 173.185 (i),
manufacturers who experience difficulty in meeting the UN Tests and
Criteria for lithium batteries may apply for an approval provided they
can demonstrate an equivalent level of safety.
Sections 173.201-173.203 and 173.211--173.213
Aluminum jerricans, 3B1 or 3B2, are added as authorized packagings
in each of these sections.
Section 173.220
Consistent with proposed changes in Sec. 176.905 for wet batteries
transported by vessel, paragraph (c)(1) is amended to remove the
reference to Sec. 176.905 and to state that a motor vehicle or
mechanical equipment which is electrically powered is not subject to
the HMR.
Section 173.224
In paragraph (b), the Self-Reactive Materials Table is amended by
adding seven new entries. The Packing Method Table for Generic Types in
paragraph (c)(3) is removed because the information is specifically
listed in the Self-Reactive Materials Table, and paragraph (c)(4) is
redesignated paragraph (c)(3).
Section 173.225
Paragraph (b) explains column headings in the Organic Peroxide
table. Specifically, paragraph (b)(2) describes the information
comprised in the column entitled ``ID Number.'' The word ``Exempt''
occasionally appears in place of an identification number, but is not
defined in Sec. 173.225. In this final rule, paragraph (b)(2) is
amended by adding a statement to clarify that the word ``Exempt,'' if
it appears in the Organic Peroxide Table, means that the material is
not regulated as an organic peroxide.
In paragraph (b)(4)(ii), the use of type B diluents for
desensitization of organic peroxides is authorized for all organic
peroxides provided that the boiling point is at least 60 deg.C (140
deg.F) greater than the SADT of the organic peroxide in a 50 kg
package. Paragraph (b)(6) is revised to indicate that lower control
temperatures are required when IBCs and bulk packagings are used.
Paragraph (c)(2), which prohibits IBCs and bulk packagings unless
authorized through an approval, is removed. The Packing Method Table
for Generic Types in paragraph (c)(3) is removed because the
information is specifically listed in the Organic Peroxides Table, and
paragraph (c)(4) is redesignated paragraph (c)(3).
Paragraph (d) is revised to consolidate two tables specifying
packagings for liquid and solid organic peroxides and self-reactive
materials into one table for both liquids and solids.
RSPA is authorizing bottom outlets for organic peroxides in bulk
packagings by removing the prohibition in the last sentence of
paragraph (e)(2) and removing paragraph (e)(3)(i)(B). Paragraph
(e)(3)(i)(C) is redesignated paragraph (e)(3)(i)(B).
Paragraph (e)(5) is revised to authorize the transport of
stabilized peroxyacetic acid, type F (containing not more than 17
percent peroxyacetic acid) in type 31A IBCs. A similar proposal made by
the United States has been approved by the UN Committee of Experts for
incorporation into the tenth revised edition of the UN Recommendations.
Section 173.226
Paragraph (c)(1) is amended to add aluminum jerricans as an
authorized packaging.
Section 173.315
When the hazard class and division assigned to ``Methylamine,
anhydrous'' was changed from Division 2.3 (poisonous gas) to Division
2.1 (flammable gas), RSPA failed to correct the Sec. 173.315 table
entry for this material by removing Notes 22 and 24. The table entry is
being corrected in this final rule.
Sections 173.316 and 173.318
RSPA proposed the addition of a requirement for mixtures of
cryogenic liquids, where charging requirements are not specifically
prescribed, to be shipped in packagings approved by the Associate
Administrator for Hazardous Materials Safety. A commenter expressed
confusion as to whether this proposal would eliminate the need for DOT
Exemption DOT-E-10001. RSPA is revising the proposed provisions in
paragraphs (d) and (f)(4) of Secs. 173.316 and 173.318, respectively,
to clarify that an approval, rather than an exemption, is needed.
Appendix E and Appendix F
As proposed, the guidelines for classification and packing group
assignment for Classes 4 and 5 are
[[Page 24698]]
removed. RSPA believes the UN Manual of Tests and Criteria is a more
appropriate reference for these test methods. The NPRM stated that by
removing Appendix E and F, RSPA will decrease the number of amendments
to the HMR necessary for consistency with the UN Manual and will reduce
the number of pages in the HMR. One commenter objected to this
proposal, claiming potential difficulty and expense in obtaining copies
of the most current version of the UN Test Manual. RSPA does not agree.
A copy of the current test manual is part of the HM-215B public record
maintained by RSPA's Dockets Unit. Upon request to the RSPA Dockets
Unit (202-366-5046), RSPA will reproduce and provide pertinent pages
from the most current UN Test Manual.
Part 175
Section 175.10
Paragraph (a)(22) is revised to allow mercury thermometers (in
addition to mercury barometers) to be carried in carry-on baggage by a
representative of a government weather bureau or similar official
agency, provided the individual advises the aircraft operator of its
presence in the baggage.
Part 176
Section 176.78
Paragraph (k), which pertains to stowage of power-operated
industrial trucks on board a vessel, is revised to correspond to
proposed revisions in Sec. 176.905.
Section 176.84
A new code 17 is added to prescribe segregation for a compressed or
liquefied gas which is toxic, flammable and corrosive.
Section 176.905
RSPA is revising requirements for transporting motor vehicles or
mechanical equipment powered by internal combustion engines by vessel
to take account of recent changes which have occurred in the IMDG Code
and in response to comments received to the NPRM and during public
outreach meetings. In Amendment 27 of the Code, the proper shipping
name ``Engines, Internal Combustion'', UN3166, was added in order to
regulate motor vehicles and other equipment powered by internal
combustion engines. However, this proper shipping name was removed and
these materials were deregulated in Amendment 28 of the IMDG Code.
Although RSPA did not propose total relief for the transport of
motor vehicles by vessel, it proposed modifying the vessel carriage
provisions to allow battery cables to remain connected in transport and
allow vehicles transported on roll-on roll-off ships to be transported
without being subject to the HMR. Additionally, revised transport
provisions for vehicles fueled with compressed gas and for certain
battery-powered vehicles were proposed to provide clarity.
One commenter suggested that RSPA remove this section from the HMR
and provide total relief for the transport of mechanical equipment
powered by internal combustion engine by vessel. RSPA believes that
total relief would not be in the best interest of safety and that
certain precautions which minimize the potential for hazardous
materials incidents involving internal combustion-powered vehicles and
equipment are warranted.
Another commenter recommended that the motor vehicle carriage
requirements in this section be adopted in the IMDG Code to alleviate
the safety and practical problems that could arise with the
deregulation of motor vehicles in Amendment 28 of the Code. Work at the
International Maritime Organization to amend the IMDG Code is beyond
the scope of this rulemaking. The commenter also noted that to require
the fuel tank to be no more than one-fourth full is somewhat arbitrary
and can be eliminated with an inspection for leaks prior to loading.
RSPA does not agree. The purpose of the quarter tank requirement is to
limit the amount of flammable vapors which would collect in an enclosed
space such as a freight container should a fuel leak occur. Although
fuel tanks sizes vary, RSPA believes that limiting the fuel present in
a vehicle's tank is a valuable safety measure necessary to alleviate
the hazard of an undetected leak during long ocean voyages. Therefore,
the proposed requirement will remain unchanged. Finally, this commenter
noted that paragraph (f) requires a fire extinguishing system capable
of alerting personnel on the bridge of a ship, which should apply
instead to the smoke or fire detection system discussed in paragraph
(g). RSPA agrees and is revising this provision accordingly.
Several provisions are added to incorporate transport safety
measures included in recently issued motor vehicle exemptions that now
allow transport of motor vehicles with batteries connected. These
provisions include a requirement for an inspection of the vehicle's
battery and associated equipment prior to loading and requiring the
removal of a vehicle's ignition key.
Part 178
Section 178.511
This section is amended to adopt requirements for aluminum
jerricans consistent with the UN Recommendations. Packaging codes 3B1
and 3B2 are added. Paragraph (b) is amended to incorporate construction
requirements for aluminum jerricans consistent with the UN
Recommendations.
Section 178.703
In paragraph (b)(6), requirements for marking inner receptacles of
31HZ2 composite IBCs are added. All inner receptacles must be marked
with the code number designating the intermediate bulk container design
type, the name or symbol of the manufacturer, the date of manufacture
and the country authorizing the allocation of the mark. In addition,
where the outer casing of a 31HZ2 IBC could be dismantled, each of the
detachable parts must be marked with the month and year of manufacture
and the name or symbol of the manufacturer.
Section 178.707
In paragraph (c)(2), a new requirement is added to indicate that
the outer packaging of 31HZ2 composite IBCs must enclose the inner
receptacles on all sides. In paragraph (c)(3) a new requirement is
added to indicate that inner receptacles of 31HZ2 composite IBCs must
consist of at least three plies of film. In paragraph (c)(6), a new
requirement is added to indicate that IBCs of type 31HZ2 must be
limited to a capacity of not more than 1250 liters.
Section 178.815
In paragraph (c)(3), the words ``which bear the stacking load'' are
added to clarify that rigid plastic IBCs and composite IBCs with
plastic outer packagings must be tested for 28 days at 40 deg.C
(104 deg.F) when the plastic outer packagings bear the stacking load.
IBCs with plastic outer packagings that are designed with metal corner
posts to bear the stacking load are not required to be tested for 28
days at 40 deg.C (104 deg.F), but must be subjected to the stacking
test for 24 hours.
IV. Rulemaking Analyses and Notices
A. Executive Order 12866 and DOT Regulatory Policies and Procedures
This final rule is not considered a significant regulatory action
under section 3(f) of Executive Order 12866 and, therefore, was not
reviewed by the Office of Management and Budget. The rule is not
considered a significant rule under the Regulatory Policies and
[[Page 24699]]
Procedures of the Department of Transportation [44 FR 11034].
The economic impact of this final rule is expected to result in
only minimal costs to certain persons subject to the HMR and may result
in modest cost savings to a small number of persons subject to the HMR
and to the agency. Most of the revised requirements adopted in this
rulemaking received industry-association support before the United
Nations Committee of Experts on the Transport of Dangerous Goods. Of
the comments received in this docket, few dealt with increased costs of
compliance. Nevertheless, RSPA believes it adequately addressed the
concerns of commenters focused on increased costs of compliance through
its adoption of a five-year extended compliance period pertaining to
package marking requirements. Because of the minimal economic impact of
this rule, preparation of a regulatory impact analysis or a regulatory
evaluation is not warranted.
B. Executive Order 12612
This final rule has been analyzed in accordance with the principles
and criteria contained in Executive Order 12612 (``Federalism'').
Federal hazardous materials transportation law, 49 U.S.C. 5701-5127,
contains an express preemption provision (49 U.S.C. 5125(b)) that
preempts State, local, and Indian tribe requirements on certain covered
subjects. Covered subjects are:
(1) The designation, description, and classification of hazardous
material;
(2) The packing, repacking, handling, labeling, marking, and
placarding of hazardous material;
(3) The preparation, execution, and use of shipping documents
related to hazardous material and requirements related to the number,
contents, and placement of those documents;
(4) The written notification, recording, and reporting of the
unintentional release in transportation of hazardous material; or
(5) The design, manufacturing, fabricating, marking, maintenance,
reconditioning, repairing, or testing of a packaging or container
represented, marked, certified, or sold as qualified for use in
transporting hazardous material.
This final rule addresses covered subjects under items (1), (2),
(3), and (5) above and, if adopted as final, would preempt State,
local, or Indian tribe requirements not meeting the ``substantively the
same'' standard. Federal hazardous materials transportation law
provides at Sec. 5125(b)(2) that if DOT issues a regulation concerning
any of the covered subjects DOT must determine and publish in the
Federal Register the effective date of Federal preemption. The
effective date may not be earlier than the 90th day following the date
of issuance of the final rule and not later than two years after the
date of issuance. RSPA has determined that the effective date of
Federal preemption for these requirements will be [insert date 180 days
after issuance of final rule] under this docket. Thus, RSPA lacks
discretion in this area, and preparation of a federalism assessment is
not warranted.
C. Regulatory Flexibility Act
This final rule incorporates changes adopted in the ninth revised
edition of the UN Recommendations, the 1997-98 ICAO Technical
Instructions, and Amendment 28 to the IMDG Code. It applies to offerors
and carriers of hazardous materials and facilitates the transportation
of hazardous materials in international commerce by providing
consistency with international requirements.
This final rule will affect small business entities that ship or
transport hazardous materials, but any adverse economic impact should
be minimal. Certain costs incurred through changes to hazard
communication and classification requirements will be minimized through
a lengthy optional compliance period, which will allow a sufficient
phase-in period to implement new provisions and deplete current
inventory affected by the new requirements. If changes already
incorporated in international standards are not adopted in this final
rule, U.S. companies, including numerous small entities competing in
foreign markets, will be at an economic disadvantage by being forced to
comply with a dual system of regulation.
Based on readily available information concerning the size and
nature of entities likely affected by this final rule, I certify this
rule will not have a significant economic impact on a substantial
number of small entities under criteria of the Regulatory Flexibility
Act.
D. Paperwork Reduction Act
The requirements for information collection have been approved by
the Office of Management and Budget (OMB) under OMB control numbers
2137-0034 for shipping papers and 2137-0557 for approvals. Under the
Paperwork Reduction Act of 1995, no person is required to respond to a
collection of information unless it displays a valid OMB control
number.
E. Regulation Identifier Number (RIN)
A regulation identifier number (RIN) is assigned to each regulatory
action listed in the Unified Agenda of Federal Regulations. The
Regulatory Information Service Center publishes the Unified Agenda in
April and October of each year. The RIN number contained in the heading
of this document can be used to cross-reference this action with the
Unified Agenda.
List of Subjects
49 CFR Part 171
Exports, Hazardous materials transportation, Hazardous waste,
Imports, Incorporation by reference, Reporting and recordkeeping
requirements.
49 CFR Part 172
Hazardous materials transportation, Hazardous waste, Labels,
Markings, Packaging and containers, Reporting and recordkeeping
requirements.
49 CFR Part 173
Hazardous materials transportation, Packaging and containers,
Radioactive materials, Reporting and recordkeeping requirements,
Uranium.
49 CFR Part 175
Air carriers, Hazardous materials transportation, Radioactive
materials, Reporting and recordkeeping requirements.
49 CFR Part 176
Hazardous materials transportation, Maritime carriers, Radioactive
materials, Reporting and recordkeeping requirements.
49 CFR Part 178
Hazardous materials transportation, Motor vehicles safety,
Packaging and containers, Reporting and recordkeeping requirements.
In consideration of the foregoing, 49 CFR Chapter I is amended as
follows:
PART 171--GENERAL INFORMATION, REGULATIONS, AND DEFINITIONS
1. The authority citation for part 171 continues to read as
follows:
Authority: 49 U.S.C. 5101-5127; 49 CFR 1.53.
2. In the Sec. 171.7(a)(3) Table, two new entries are added in
numerical order under the entry for American Society for Testing and
Materials and the last entry under the entry for United Nations is
revised, to read as follows:
Sec. 171.7 Reference material.
(a) Matter incorporated by reference. * * *
[[Page 24700]]
(3) Table of material incorporated by reference. * * *
----------------------------------------------------------------------------------------------------------------
Source and name of material 49 CFR reference
----------------------------------------------------------------------------------------------------------------
* * * * * *
*
American Society for Testing and Materials
* * * * * *
*
ASTM D 3828-93, Standard Test Methods for Flash Point by 173.120.
Small Scale Closed Tester.
ASTM D 4206-96 Standard Test Method for Sustained Burning 173.120.
of Liquid Mixtures Using the Small Scale Open-Cup
Apparatus.
* * * * * *
*
United Nations
* * * * * *
*
UN Recommendations on the Transport of Dangerous Goods, 173.21, 173.56 173.57,
Manual of Tests and Criteria, Second Revised Edition, 1995. 173.124 173.128, 173.166
173.185.
----------------------------------------------------------------------------------------------------------------
* * * * *
Sec. 171.7 [Amended]
3. In addition, in Sec. 171.7, in the table in paragraph (a)(3),
the following changes are made:
a. In the entry ASTM D 93-90, the wording ``D 93-90'' is revised to
read ``D 93-94''.
b. In the entry ASTM D 3278-89, the wording ``D 3278-89'' is
revised to read ``D 3278-95''.
c. In the entry ASTM G 31-72, the wording ``(Reapproved 1990)'' is
revised to read ``(Reapproved 1995)'.
d. Under Transport Canada, the entry ``Transportation of Dangerous
Goods Regulations, 1 July 1985'' is amended by revising the reference
``and SOR/94-264 (English edition)'' at the end of the entry to read
``, SOR/94-264 (English edition), SOR/95-241, and SOR/95-547''.
e. Under United Nations, for the entry ``UN Recommendations on the
Transport of Dangerous Goods, Eighth Revised Edition (1993)'' the
wording ``Eighth Revised Edition (1993)'' is revised to read ``Ninth
Revised Edition (1995)''.
4. In Sec. 171.8, the following definitions are added in the
appropriate alphabetical order to read as follows:
Sec. 171.8 Definitions and abbreviations.
* * * * *
Aerosol means any non-refillable metal receptacle containing a gas
compressed, liquefied or dissolved under pressure, the sole purpose of
which is to expel a nonpoisonous (other than a Division 6.1 Packing
Group III material) liquid, paste, or powder and fitted with a self-
closing release device allowing the contents to be ejected by the gas.
* * * * *
Intermediate packaging means a packaging which encloses an inner
packaging or article and is itself enclosed in an outer packaging.
* * * * *
SADT means self-accelerated decomposition temperature. See
Sec. 173.21(f) of this subchapter.
Salvage packaging means a special packaging conforming to
Sec. 173.3 of this subchapter into which damaged, defective or leaking
hazardous materials packages, or hazardous materials that have spilled
or leaked, are placed for purposes of transport for recovery or
disposal.
* * * * *
5. In Sec. 171.11, paragraph (d)(4) is revised and a new paragraph
(d)(14) is added, to read as follows:
Sec. 171.11 Use of ICAO Technical Instructions.
* * * * *
(d) * * *
(4) When a hazardous material that is regulated by this subchapter
for transportation by highway is transported by motor vehicle on a
public highway under the provisions of this section, the following
requirements apply:
(i) The motor vehicle must be placarded in accordance with subpart
F of part 172 of this subchapter; and
(ii) The shipping paper must include an indication that the
shipment is being made under the provisions of this section or must
include the letters ``ICAO.''
* * * * *
(14) An aerosol must meet the definition for ``Aerosol'' in
Sec. 171.8.
Sec. 171.11 [Amended]
6. In addition, in Sec. 171.11, in paragraph (d)(9)(i), the wording
`` `Poison-Inhalation Hazard' '' is revised to read `` `Toxic
Inhalation Hazard' or `Poison Inhalation Hazard' ''.
7. In Sec. 171.12, a new paragraph (b)(17) is added to read as
follows:
Sec. 171.12 Import and export shipments.
* * * * *
(b) * * *
(17) An aerosol must meet the definition for ``Aerosol'' in
Sec. 171.8.
* * * * *
Sec. 171.12 [Amended]
8. In addition, in Sec. 171.12, the following changes are made:
a. In paragraph (b)(8)(i), the wording `` `Poison-Inhalation
Hazard' '' is revised to read `` `Toxic Inhalation Hazard' or `Poison
Inhalation Hazard' ''.
b. Paragraph (b)(13) is removed and reserved.
9. In Sec. 171.12a, a new paragraph (b)(16) is added to read as
follows:
Sec. 171.12a Canadian shipments and packagings.
* * * * *
(b) * * *
(16) An aerosol must meet the definition for ``Aerosol'' in
Sec. 171.8.
Sec. 171.12a [Amended]
10. In addition, in Sec. 171.12a, the following changes are made:
a. In paragraph (b)(5)(i), the wording `` `Poison-Inhalation
Hazard' '' is revised to read `` `Toxic Inhalation Hazard' or `Poison
Inhalation Hazard' ''.
b. Paragraph (b)(12) is removed and reserved.
11. Section 171.14 is amended by adding a new paragraph (d) to read
as follows:
Sec. 171.14 Transitional provisions for implementing requirements
based on the UN Recommendations.
* * * * *
[[Page 24701]]
(d) A rule published in the Federal Register on May 6, 1997,
effective October 1, 1997, resulted in revisions to this subchapter.
During the transition period provided in paragraph (d)(1) of this
section, a person may elect to comply with either the applicable
requirements of this subchapter in effect on September 30, 1997, or the
requirements of this subchapter in the May 6, 1997 final rule, in
effect on October 1, 1997.
(1) Transition date. On October 1, 1998, all applicable regulatory
requirements adopted in the May 6, 1997 final rule in effect on October
1, 1997 must be met.
(2) Intermixing old and new requirements. Prior to the transition
date in paragraph (d)(1) of this section, it is recommended that the
hazard communication requirements be consistent where practicable,
i.e., marking, labeling, placarding, and shipping paper descriptions
should conform to either the old requirements of this subchapter in
effect on September 30, 1997, or new requirements of this subchapter in
the May 6, 1997 rule, in effect on October 1, 1997, without intermixing
of communication elements. However, intermixing is permitted, during
the applicable transition period, for packaging, hazard communication,
and handling provisions, as follows:
(i) If either shipping names or identification numbers are
identical, a shipping paper may display the old shipping description
even if the package is marked and labeled under the new shipping
description;
(ii) If either shipping names or identification numbers are
identical, a shipping paper may display the new shipping description
even if the package is marked and labeled under the old shipping
description; and
(iii) Either old or new placards may be used regardless of whether
old or new shipping descriptions and package markings are used.
PART 172--HAZARDOUS MATERIALS TABLE, SPECIAL PROVISIONS, HAZARDOUS
MATERIALS COMMUNICATIONS, EMERGENCY RESPONSE INFORMATION, AND
TRAINING REQUIREMENTS
12. The authority citation for part 172 continues to read as
follows:
Authority: 49 U.S.C. 5101-5127; 49 CFR 1.53.
13. In Sec. 172.101, new paragraphs (c)(14), (c)(15), and (l)(3)
are added to read as follows:
Sec. 172.101 Purpose and use of hazardous materials table.
* * * * *
(c) * * *
(14) A proper shipping name that describes all isomers of a
material may be used to identify any isomer of that material if the
isomer meets criteria for the same hazard class or division, subsidiary
risk(s) and packing group, unless the isomer is specifically identified
in the Table.
(15) Hydrates of inorganic substances may be identified using the
proper shipping name for the equivalent anhydrous substance if the
hydrate meets the same hazard class or division, subsidiary risk(s) and
packing group, unless the hydrate is specifically identified in the
Table.
* * * * *
(l) * * *
(3) The proper shipping name of a hazardous material changed in the
May 6, 1997 final rule, in effect on October 1, 1997, only by the
addition or omission of the word ``compressed,'' ``inhibited,''
``liquefied'' or ``solution'' may continue to be used to comply with
package marking requirements, until January 1, 2003.
* * * * *
Sec. 172.101 [Amended]
14. In addition, in Sec. 172.101, in paragraph (f), in the second
sentence, the wording ``Classes 2 and 7 materials and ORM-D materials''
is revised to read ``Class 2, Class 7, Division 6.2 (other than
regulated medical wastes), and ORM-D materials''.
15. In Sec. 172.101, the Hazardous Materials Table is amended by
removing, adding, or revising, in appropriate alphabetical sequence,
the following entries to read as follows:
Sec. 172.101 Purpose and use of hazardous materials table.
* * * * *
[[Page 24702]]
Sec. 172.101--Hazardous Materials Table
Hazardous (8) Packaging (Sec. 173. * * *) (9) Quantity limitations (10) Vessel stowage
materials ---------------------------------------------------------------------------------------------------------------
Symbols descriptions and Hazard class Identification PG Label codes Special
proper shipping or division numbers provisions Exceptions Non-bulk Bulk Passenger Cargo aircraft Location Other
names aircraft/rail only
(1) (2).............. (3)........... (4)............. (5)........... (6).............. (7)........... (8A).......... (8B).......... (8C).......... (9A).......... (9B).......... (10A)......... (10B)
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
[REMOVE]
* * * * * * *
Aluminum .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
processing by-
products (both
entries).
* * * * * * *
I............... Ammonia, .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
anhydrous,
liquefied or
Ammonia
solutions,
relative density
less than 0.880
at 15 degrees C
in water, with
more than 50
percent ammonia.
D............... Ammonia, .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
anhydrous,
liquefied or
Ammonia
solutions,
relative density
less than 0.880
at 15 degrees C
in water, with
more than 50
percent ammonia.
* * * * * * *
n-Amylene........ .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
D............... Boosters with .............. NA0350.......... .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
detonator.
* * * * * * *
2-Bromo-2- .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
nitropropane-1,3-
diol.
* * * * * * *
Butoxyl.......... .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
* * * * * * *
n-Butyl bromide.. .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
* * * * * * *
Butylpropionate.. .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
* * * * * * *
Carbon dioxide .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
and oxygen
mixtures.
[[Page 24703]]
* * * * * * *
Chemical kits .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
(must be
classified and
labelled
according to the
hazard class of
the
constitutent(s)
and must meet
the requirements
of special
provision 15 in
172.102(c)(1)).
* * * * * * *
Chlorite solution .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
with more than 5
percent but less
than 16 percent
available
chlorine.
Chlorite solution .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
with not less
than 16 percent
available
chlorine.
* * * * * * *
Coating solution .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
(both entries).
* * * * * * *
Dibromobenzene... .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
* * * * * * *
Dichloropropane, .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
see Propylene
dichloride.
* * * * * * *
Diethylaminoethan .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
ol.
* * * * * * *
Diphenylmethane- .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
4,4'-
diisocyanate.
* * * * * * *
Engine starting .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
fluid, with
flammable gas.
* * * * * * *
Ethylene glycol .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
monobutyl ether.
* * * * * * *
Explosive pest .............. NA0006.......... .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
control devices.
Explosive pest .............. NA0412.......... .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
control devices.
* * * * * * *
Firelighters, .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
solid with
flammable liquid
(both entries).
* * * * * * *
Furfural......... .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
* * * * * * *
Gas, refrigerated .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
liquid, n.o.s.
[[Page 24704]]
* * * * * * *
Halogenated .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
irritating
liquids, n.o.s.
(all three
entries).
* * * * * * *
Hexaethyl .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
tetraphosphate,
liquid (PG I and
III).
* * * * * * *
Hexaethyl .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
tetraphosphate,
solid (PG I and
III).
* * * * * * *
Hypochlorite .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
solutions with
more than 5
percent but less
than 16 percent
available
chlorine.
Hypochlorite .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
solutions with
16 percent or
more available
chlorine.
* * * * * * *
Mannitol .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
hexanitrate,
wetted or
Nitromannite,
wetted with not
less than 40
percent water,
by mass or
mixture of
alcohol and
water.
* * * * * * *
Methyl benzoate.. .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
* * * * * * *
Methyl vinyl .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
ketone.
* * * * * * *
Nitrosoguanidine. .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
* * * * * * *
tert-Octyl .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
mercaptan.
* * * * * * *
Pentan-2,4-dione. .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
* * * * * * *
Percarbonates, .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
inorganic, n.o.s.
[[Page 24705]]
* * * * * * *
Plastic molding .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
material in
dough, sheet or
extruded rope
form.
* * * * * * *
Potassium salts
of aromatic
nitro-
derivatives,
explosive.
* * * * * * *
Propellant, .............. NA0474.......... .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
explosive,
liquid.
* * * * * * *
Propellant .............. NA0477.......... .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
explosive,
liquid.
* * * * * * *
Propylene .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
dichloride.
* * * * * * *
Selenium powder.. .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
* * * * * * *
Sodium .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
percarbonate.
* * * * * * *
Sodium salts of
aromatic nitro-
derivatives,
n.o.s. explosive.
* * * * * * *
Tributylamine.... .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
* * * * * * *
Trifluorochloroet .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
hylene,
inhibited, R1113.
* * * * * * *
Trifluoromethane .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
and
chlorotrifluorom
eth- ane mixture
(constant
boiling mixture)
(R503).
* * * * * * *
Triisocyanatoisoc .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
yanurate of
isophoronediisoc
yanate,
solution, with
70 percent, by
mass.
* * * * * * *
[ADD:]
* * * * * * *
Adhesives, 3............. UN1133.......... I............. 3................ B42, T7, T30.. 150........... 201........... 243........... 1 L........... 30 L.......... B............. ..............
containing a
flammable liquid.
* * * * * * *
Aerosols, 2.1........... UN1950.......... .............. 2.1.............. N82........... 306........... None.......... None.......... Forbidden..... Forbidden..... A............. 40, 48, 85
flammable,
n.o.s. (engine
starting fluid)
(each not
exceeding 1 L
capacity).
[[Page 24706]]
* * * * * * *
Aluminum smelting 4.3........... UN3170.......... II............ 4.3.............. B106, B115.... None.......... 212........... 242........... 15 kg......... 50 kg......... B............. 85, 103
by-products or
Aluminum
remelting by-
products.
................. .............. ................ III........... 4.3.............. B106, B115.... None.......... 213........... 241........... 25 kg......... 100 kg........ B............. 85, 103
* * * * * * *
2-Amino-4,6- 4.1........... UN3317.......... I............. 4.1.............. 23,A8, A19, None.......... 211........... None.......... 1 kg.......... 15 kg......... E............. 28, 36
Dinitrophenol, A20, N41.
wetted with not
less than 20
percent water by
mass.
* * * * * * *
I............... Ammonia, 2.3........... UN1005.......... .............. 2.3, 8........... 4............. None.......... 304........... 314, 315...... Forbidden..... 25 kg......... D............. 40, 57
anhydrous.
D............... Ammonia, 2.2........... UN1005.......... .............. 2.2.............. 13............ None.......... 304........... 314, 315...... Forbidden..... 25 kg......... D............. 40, 57
anhydrous.
* * * * * * *
D............... Ammonia solution, 2.2........... UN3318.......... .............. 2.2.............. 13............ None.......... 304........... 314, 315...... Forbidden..... 25 kg......... D............. 40, 57
relative density
less than 0.880
at 15 degrees C
in water, with
more than 50
percent ammonia.
I............... Ammonia solution, 2.3........... UN3318.......... .............. 2.3, 8........... 4............. None.......... 304........... 314, 315...... Forbidden..... 25 kg......... D............. 40, 57
relative density
less than 0.880
at 15 degrees C
in water, with
more than 50
percent ammonia.
* * * * * * *
2-Bromo-2- 4.1........... UN3241.......... III........... 4.1.............. 46............ 151........... 213........... None.......... 25 kg......... 50 kg......... C............. 12, 25, 40
nitropropane-1,3-
diol.
* * * * * * *
1-Bromobutane.... 3............. UN1126.......... II............ 3................ T1............ 150........... 202........... 242........... 5L............ 60L........... B............. 40
* * * * * * *
Dn-Butyl ................. .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. ..............
bromide, see 1-
Bromobutane
* * * * * * *
Butyl propionates 3............. UN1914.......... III........... 3................ B1,T1......... 150........... 203........... 242........... 60 L.......... 220 L......... A............. ..............
* * * * * * *
Calcium chlorate 5.1........... UN2429.......... .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
aqueous solution.
[ADD]
................. .............. ................ III........... 5.1.............. A2, N41, T8... 152........... 203........... 241........... 2.5L.......... 30 L.......... B............. 56, 68, 106
[[Page 24707]]
* * * * * * *
Carbon dioxide 2.2........... UN1014.......... .............. 2.2, 5.1......... 77............ 306........... 304........... 314, 315...... 75 kg......... 150 kg........ A............. ..............
and oxygen
mixtures,
compressed.
* * * * * * *
Chemical kits or 9............. UN3316.......... .............. 9................ 15............ None.......... None.......... None.......... 10 kg......... 10 kg......... A............. ..............
First aid kits
(containing
hazardous
materials).
* * * * * * *
Chlorite solution 8............. UN1908.......... II............ 8................ A3,A6, A7, B2, 154........... 202........... 242........... 1 L........... 30 L.......... B............. 26
N34, T8.
................. .............. ................ III........... 8................ A3,A6, A7, B2, 154........... 203........... 241........... 5 L........... 60 L.......... B............. 26
N34, T8.
* * * * * * *
Coating solution 3............. UN1139.......... I............. 3................ T42........... 150........... 201........... 243........... 1 L........... 30 L.......... E............. ..............
(includes
surface
treatments or
coatings used
for industrial
or other
purposes such as
vehicle
undercoating,
drum or barrel
lining).
II............ 3................ T7,T30........ 150........... 202........... 242........... 5 L........... 60 L.......... B............. ..............
III........... 3................ B1,T7,T30..... 150........... 203........... 242........... 60 L.......... 220 L......... A............. ..............
* * * * * * *
1............... Compressed gas, 2.3........... UN3304.......... .............. 2.3, 8........... 1............. None.......... 192........... 245........... Forbidden..... Forbidden..... D............. 40
toxic,
corrosive,
n.o.s.
Inhalation
Hazard Zone A.
I............... Compressed gas, 2.3........... UN3304.......... .............. 2.3, 8........... 2............. None.......... 302, 305...... 314, 315...... Forbidden..... Forbidden..... D............. 40
toxic,
corrosive,
n.o.s.
Inhalation
Hazard Zone B.
I............... Compressed gas, 2.3........... UN3304.......... .............. 2.3, 8........... 3............. None.......... 302, 305...... 314, 315...... Forbidden..... Forbidden..... D............. 40
toxic,
corrosive,
n.o.s.
Inhalation
Hazard Zone C.
I............... Compressed gas, 2.3........... UN3304.......... .............. 2.3, 8........... 4............. None.......... 302, 305...... 314, 315...... Forbidden..... Forbidden..... D............. 40
toxic,
corrosive,
n.o.s.
Inhalation
Hazard Zone D.
I............... Compressed gas, 2.3........... UN3305.......... 2.3, 2.1, 8... 1................ None.......... 192........... 245........... Forbidden..... Forbidden..... D............. 17, 40........
toxic,
flammable,
corrosive,
n.o.s.
Inhalation
Hazard Zone A.
I............... Compressed gas, 2.3........... UN3305.......... 2.3, 2.1, 8... 2................ None.......... 302, 305...... 314, 315...... Forbidden..... Forbidden..... D............. 17, 40........
toxic,
flammable,
corrosive,
n.o.s.
Inhalation
Hazard Zone B.
I............... Compressed gas, 2.3........... UN3305.......... 2.3, 2.1, 8... 3................ None.......... 302, 305...... 314, 315...... Forbidden..... Forbidden..... D............. 17, 40........
toxic,
flammable,
corrosive,
n.o.s.
Inhalation
Hazard Zone C.
I............... Compressed gas, 2.3........... UN3305.......... 2.3, 2.1, 8... 4................ None.......... 302, 305...... 314, 315...... Forbidden..... Forbidden..... D............. 17, 40........
toxic,
flammable,
corrosive,
n.o.s.
Inhalation
Hazard Zone D.
I............... Compressed gas, 2.3........... UN3306.......... 2.3, 5.1, 8... 1................ None.......... 192........... 244........... Forbidden..... Forbidden..... D............. 40, 89, 90....
toxic, oxdizing,
corrosive,
n.o.s.
Inhalation
Hazard Zone A.
[[Page 24708]]
I............... Compressed gas, 2.3........... UN3306.......... 2.3, 5.1, 8... 2................ None.......... 302, 305...... 314, 315...... Forbidden..... Forbidden..... D............. 40, 89, 90....
toxic,
oxidizing,
corrosive,
n.o.s.
Inhalation
Hazard Zone B.
I............... Compressed gas, 2.3........... UN3306.......... 2.3, 5.1, 8... 3................ None.......... 302, 305...... 314, 315...... Forbidden..... Forbidden..... D............. 40, 89, 90....
toxic,
oxidizing,
corrosive,
n.o.s.
Inhalation
Hazard Zone C.
I............... Compressed gas, 2.3........... UN3306.......... 2.3, 5.1, 8... 4................ None.......... 302, 305...... 314, 315...... Forbidden..... Forbidden..... D............. 40, 89, 90....
toxic,
oxidizing,
corrosive,
n.o.s.
Inhalation
Hazard Zone D.
Compressed gas, 2.3........... UN3303.......... 2.3, 5.1...... 1................ None.......... 192........... 245........... Forbidden..... Forbidden..... D............. 40............
toxic,
oxidizing,
n.o.s.
Inhalation
Hazard Zone A.
Compressed gas, 2.3........... UN3303.......... 2.3, 5.1...... 2................ None.......... 302, 305...... 314, 315...... Forbidden..... Forbidden..... D............. 40............
toxic,
oxidizing,
n.o.s.
Inhalation
Hazard Zone B.
Compressed gas, 2.3........... UN3303.......... 2.3, 5.1...... 3................ None.......... 302, 305...... 314, 315...... Forbidden..... Forbidden..... D............. 40............
toxic,
oxidizing,
n.o.s.
Inhalation
Hazard Zone C.
Compressed gas, 2.3........... UN3303.......... 2.3, 5.1...... 4................ None.......... 302, 305...... 314, 315...... Forbidden..... Forbidden..... D............. 40............
toxic,
oxidizing,
n.o.s.
Inhalation
Hazard Zone D.
* * * * * * *
Detonator 1.4S.......... UN0500.......... II............ 1.4S............. 104........... 63(f), 63(g).. 62............ None.......... 25 kg......... 100 kg........ A............. ..............
assemblies, non-
electric for
blasting.
* * * * * * *
1,2- 3............. UN1279.......... II............ 3................ N36,T1........ 150........... 202........... 242........... 5 L........... 60 L.......... B............. ..............
Dichloropropane.
* * * * * * *
2- 8............. UN2686.......... II............ 8,3.............. B2,T15, T26... None.......... 202........... 243........... 1 L........... 30 L.......... A............. ..............
Diethylaminoetha
nol.
2- 6.1........... UN3302.......... II............ 6.1.............. T8............ None.......... 202........... 243........... 5 L........... 60 L.......... D............. 25
Dimethylaminoeth
yl acrylate.
* * * * * * *
Disinfectant, 8............. UN1903.......... I............. 8................ A7, B10, T42.. None.......... 201........... 243........... 0.5 L......... 2.5 L......... B............. ..............
liquid,
corrosive, n.o.s.
* * * * * * *
Dyes, liquid, 8............. UN2801.......... I............. 8................ 11, B10....... None.......... 201........... 243........... 0.5 L......... 2.5 L......... A............. ..............
corrosive,
n.o.s. or Dye
intermediates,
liquid,
corrosive,
n.o.s..
* * * * * * *
Firelighters, 4.1........... UN2623.......... III........... 4.1.............. A1, A19....... None.......... 213........... None.......... 25 kg......... 100 kg........ A............. ..............
solid with
flammable liquid.
* * * * * * *
Furaldehydes..... 6.1........... UN1199.......... II............ 6.1, 3........... T15........... None.......... 202........... 243........... 5 L........... 60 L.......... A............. ..............
* * * * * * *
Gas cartridges, 2.1........... UN2037.......... .............. 2.1............ .............. 306......... 304......... None........ 1 kg........ 15 kg....... B........... 40.
(flammable)
without a
release
device,non-re-
fillable.
[[Page 24709]]
* * * * * * *
Gas, refrigerated 2.1........... UN3312........ .............. 2.1............ .............. None........ 316........... 318........... Forbidden..... Forbidden..... D............. 40
liquid,
flammable,
n.o.s.
(cryogenic
liquid).
Gas, refrigerated 2.2........... UN3158........ .............. 2.2............ .............. 320......... 316........... 318........... 50 kg......... 500 kg........ D............. ..............
liquid, n.o.s.
(cryogenic
liquid).
Gas, refrigerated 2.2........... UN3311........ .............. 2.2, 5.1....... .............. 320......... 316........... 318........... Forbidden..... Forbidden..... D............. ..............
liquid,
oxidizing,
n.o.s.
(cryogenic
liquid).
* * * * * * *
Hypochlorite 8............. UN1791.......... II............ 8................ A7, B2, B15, 154........... 202........... 242........... 1 L........... 30 L.......... B............. 26
solutions. N34, T7.
III........... 8................ B104, N34, T7. 154........... 203........... 241........... 5 L........... 60 L.......... B............. 26
* * * * * * *
I............... Liquefied gas, 2.3........... UN3308.......... .............. 2.3, 8........... 1............. None.......... 192........... 245........... Forbidden..... Forbidden..... D............. 40
toxic,
corrosive,
n.o.s.
Inhalation
Hazard Zone A.
I............... Liquefied gas, 2.3........... UN3308.......... .............. 2.3, 8........... 2............. None.......... 304........... 314, 315...... Forbidden..... Forbidden..... D............. 40
toxic,
corrosive,
n.o.s.
Inhalation
Hazard Zone B.
I............... Liquefied gas, 2.3........... UN3308.......... .............. 2.3, 8........... 3............. None.......... 304........... 314, 315...... Forbidden..... Forbidden..... D............. 40
toxic,
corrosive,
n.o.s.
Inhalation
Hazard Zone C.
I............... Liquefied gas, 2.3........... UN3308.......... .............. 2.3, 8........... 4............. None.......... 304........... 314, 315...... Forbidden..... Forbidden..... D............. 40
toxic,
corrosive,
n.o.s.
Inhalation
Hazard Zone D.
I............... Liquefied gas, 2.3........... UN3309.......... .............. 2.3, 2.1, 8...... 1............. None.......... 192........... 245........... Forbidden..... Forbidden..... D............. 17, 40
toxic,
flammable,
corrosive,
n.o.s.
Inhalation
Hazard Zone A.
I............... Liquefied gas 2.3........... UN3309.......... .............. 2.3, 2.1, 8...... 2............. None.......... 304........... 314, 315...... Forbidden..... Forbidden..... D............. 17, 40
toxic,
flammable,
corrosive,
n.o.s.
Inhalation
Hazard Zone B.
I............... Liquefied gas, 2.3........... UN3309.......... .............. 2.3, 2.1, 8...... 3............. None.......... 304........... 314, 315...... Forbidden..... Forbidden..... D............. 17, 40
toxic,
flammable,
corrosive,
n.o.s.
Inhalation
Hazard Zone C.
I............... Liquefied gas, 2.3........... UN3309.......... .............. 2.3, 2.1, 8...... 4............. None.......... 304........... 314, 315...... Forbidden..... Forbidden..... D............. 17, 40
toxic,
flammable,
corrosive,
n.o.s.
Inhalation
Hazard Zone D.
* * * * * * *
I............... Liquefied gas, 2.3........... UN3310.......... .............. 2.3, 5.1, 8...... 1............. None.......... 192........... 245........... Forbidden..... Forbidden..... D............. 40, 89, 90
toxic,
oxidizing,
corrosive,
n.o.s.
Inhalation
Hazard Zone A.
I............... Liquefied gas, 2.3........... UN3310.......... .............. 2.3, 2.1, 8...... 2............. None.......... 304........... 314, 315...... Forbidden..... Forbidden..... D............. 40, 89, 90
toxic,
oxidizing,
corrosive,
n.o.s.
Inhalation
Hazard Zone B.
I............... Liquefied gas, 2.3........... UN3310.......... .............. 2.3, 2.1, 8...... 3............. None.......... 304........... 314, 315...... Forbidden..... Forbidden..... D............. 40, 89, 90
toxic,
oxidizing,
corrosive,
n.o.s.
Inhalation
Hazard Zone C.
I............... Liquefied gas, 2.3........... UN3310.......... .............. 2.3, 2.1, 8...... 4............. None.......... 304........... 314, 315...... Forbidden..... Forbidden..... D............. 40, 89, 90
toxic,
oxidizing,
corrosive,
n.o.s.
Inhalation
Hazard Zone D.
[[Page 24710]]
Liquefied gas, 2.3........... UN3307.......... .............. 2.3, 5.1......... 1............. None.......... 192........... 245........... Forbidden..... Forbidden..... D............. 40
toxic,
oxidizing,
n.o.s.
Inhalation
Hazard Zone A.
Liquefied gas, 2.3........... UN3307.......... .............. 2.3, 5.1......... 2............. None.......... 304........... 314, 315...... Forbidden..... Forbidden..... D............. 40
toxic,
oxidizing, n.o.s
Inhalation
Hazard Zone B.
Liquefied gas, 2.3........... UN3307.......... .............. 2.3, 5.1......... 3............. None.......... 304........... 314, 315...... Forbidden..... Forbidden..... D............. 40
toxic,
oxidizing,
n.o.s.
Inhalation
Hazard Zone C.
Liquefied gas, 2.3........... UN3307.......... .............. 2.3, 5.1......... 4............. None.......... 304........... 314, 315...... Forbidden..... Forbidden..... D............. 40
toxic,
oxidizing,
n.o.s.
Inhalation
Hazard Zone D.
* * * * * * *
Mannitol 1.1D.......... UN0133.......... II............ 1.1D............. 121........... None.......... 62............ None.......... Forbidden..... Forbidden..... B............. 1E, 5E
hexanitrate,
wetted or
Nitromannite,
wetted with not
less than 40
percent water,
or mixture of
alcohol and
water, by mass.
* * * * * * *
2-Methyl-2- 6.1........... UN3023.......... I............. 6.1, 3........... 2, B9, B14, None.......... 227........... 244........... Forbidden..... Forbidden..... D............. 40, 102
heptanethiol. B32, B74,
T38, T43, T45.
* * * * * * *
Methyl vinyl 6.1........... UN1251.......... I............. 6.1, 3, 8........ 1, 25, B9, None.......... 226........... 244........... Forbidden..... Forbidden..... B............. 40
ketone, B14, B30,
stabilized. B72, T38,
T43,T44.
* * * * * * *
Nitroglycerin 4.1........... UN3319.......... .............. 4.1.............. 118........... None.......... None.......... None.......... Forbidden..... 0.5 kg........ E............. ..............
mixture with
more than 2
percent but not
more than 10
percent
nitroglycerin,
by mass,
desensitized.
* * * * * * *
Organic pigments, 4.2........... UN3313.......... II............ 4.2.............. None.......... None.......... 212........... 241........... 15 kg......... 50 kg......... C............. ..............
self-heating.
................. .............. ................ III........... 4.2.............. B101.......... None.......... 213........... 241........... 25 kg......... 100 kg........ C............. ..............
* * * * * * *
Oxidizing liquid, 5.1........... UN3139.......... I............. 5.1.............. 127, A2....... None.......... 201........... 243........... Forbidden..... 2.5 L......... D............. 56, 58, 69,
n.o.s. 106
[[Page 24711]]
* * * * * * *
Paint including 3............. UN1263.......... I............. 3................ T8, T31....... 150........... 201........... 243........... 1 L........... 30 L.......... E............. ..............
paint, lacquer,
enamel, stain,
shellac
solutions,
varnish, polish,
liquid filler,
and liquid
lacquer base.
* * * * * * *
Paint related 3............. UN1263.......... I............. 3................ T8, T31....... 150........... 201........... 243........... 1 L........... 30 L.......... E............. ..............
material
including paint
thinning,
drying,
removing, or
reducing
compound.
* * * * * * *
Pentane-2,4-dione 3............. UN2310.......... III........... 3, 6.1........... B1, T1........ 150........... 203........... 242........... 60 L.......... 220 L......... A............. ..............
* * * * * * *
1-Pentene (n- 3............. UN1108.......... I............. 3................ T14........... 150........... 201........... 243........... 1 L........... 30 l.......... E............. ..............
amylene).
* * * * * * *
Perchlorates, 5.1........... UN3211.......... .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
inorganic,
aqueous
solution, n.o.s.
[ADD] .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
III........... 5.1.............. T8............ 152........... 203........... 241........... 2.5 L......... 30 L.......... B............. 56, 58, 69,
106
* * * * * * *
Plastic molding 9............. UN3314.......... III........... 9................ 32............ 155........... 213........... None.......... 100 kg........ 200 kg........ A............. 85, 87
compound in
dough, sheet or
extruded rope
form evolving
flammable vapor.
* * * * * * *
Potassium 5.1........... UN2427.......... .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
chlorate,
aqueous solution.
[ADD] .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. ..............
III........... 5.1.............. A2, T8........ 152........... 203........... 241........... 2.5 L......... 30 L.......... B............. 56, 58,
69, 106
* * * * * * *
Resin solution, 3............. UN1866.......... I............. 3................ B52, T8, T31.. 150........... 201........... 243........... 1 L........... 30 L.......... E............. ..............
flammable.
* * * * * * *
Sodium 8............. UN3320.......... II............ 8................ B2, N34, T8... 154........... 202........... 242........... 1 L........... 30 L.......... A............. 26
borohydride and
sodium hydroxide
solution, with
not more than 12
percent sodium
borohydride and
not more than 40
percent sodium
hydroxide by
mass.
III........... 8................ B2, N34, T7... 154........... 203........... 241........... 5 L........... 60 L.......... A............. ..............
* * * * * * *
Sodium chlorate, 5.1........... UN2428.......... .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
aqueous solution.
[ADD]............ .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
III........... 5.1.............. A2, T8........ 152........... 203........... 241........... 2.5 L......... 30 L.......... B............. 56, 58, 69,
106
[[Page 24712]]
* * * * * * *
Tributylamine.... 6.1........... UN2542.......... II............ 6.1.............. B110, T14..... None.......... 202........... 243........... 5 L........... 60 L.......... A............. ..............
* * * * * * *
Trifluorochloroet 2.3........... UN1082.......... .............. 2.3, 2.1......... 3,B14......... None.......... 304........... 314, 315...... Forbidden..... Forbidden..... D............. 40
hylene,
inhibited.
* * * * * * *
[REVISE:] .............. ................ .............. ................. .............. .............. .............. .............. .............. .............. .............. ..............
* * * * * * *
Chloroacetone, 6.1........... UN1695.......... I............. 6.1,3,8.......... 2, B9, B14, None.......... 227........... 244........... Forbidden..... Forbidden..... D............. 20, 40, 95
stabilized. B32, B74,
N12, N32,
N34, T38,
T43, T45.
* * * * * * *
Cyclohexyl 6.1........... UN2488.......... I............. 6.1, 3........... 2,B9, B14,B32, None.......... 227........... 244........... Forbidden..... Forbidden..... D............. 20, 40, 95
isocyanate. B74,B77, T38,
T43, T45.
* * * * * * *
Methyl 6.1........... UN2295.......... I............. 6.1, 3........... T42........... None.......... 201........... 243........... 1 L........... 30 L.......... D............. ..............
chloroacetate.
* * * * * * *
Methyl 6.1........... UN2477.......... I............. 6.1,3............ 2, B9, B14, None.......... 227........... 244........... Forbidden..... Forbidden..... A............. ..............
isothiocyanate. B32, B74,
T38, T43, T45.
* * * * * * *
Phenyl isocyanate 6.1........... UN2487.......... I............. 6.1,3............ 2, B9, B14, None.......... 227........... 244........... Forbidden..... Forbidden..... D............. 20, 40, 95
B32, B74,
B77, N33,
N34, T38,
T43, T45.
[[Page 24713]]
* * * * * * *
Phosphorus 6.1........... UN1809.......... I............. 6.1, 8........... 2, B9, B14, None.......... 227........... 244........... Forbidden..... Forbidden..... C............. 40
trichloride. B15, B32,
B74, B77,
N34, T38,
T43, T45.
* * * * * * *
Vinylpyridines, 6.1........... UN3073.......... II............ 6.1, 3, 8........ B100, T8...... None.......... 202........... 243........... 1 L........... 30 L.......... B............. 40
inhibited.
* * * * * * *
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
[[Page 24714]]
Sec. 172.101 [Amended]
16. In addition, in the Sec. 172.101 Hazardous Materials Table, the
following changes are made:
16-1. In Column (2), the following hazardous materials descriptions
and proper shipping names are revised as follows:
----------------------------------------------------------------------------------------------------------------
Current column (2) entry Revise to read:
----------------------------------------------------------------------------------------------------------------
Air bag inflators or Air bag modules or Seat-belt pre- Air bag inflators or Air bag modules or Seat-belt
tensioners or Seat-belt modules. pretensioners.
Aircraft evacuation slides, see Life saving appliances Aircraft evacuation slides, see Life saving appliances
etc.. etc.
Aircraft survival kits, see Life saving appliances etc. Aircraft survival kits, see Life saving appliances etc.
Alcohols, toxic, n.o.s................................. Alcohols, flammable, toxic, n.o.s
Aldehydes, toxic, n.o.s................................ Aldehydes, flammable, toxic, n.o.s.
Amyl methyl ketone..................................... n-Amyl methyl ketone.
Arsenic compounds, liquid, n.o.s. including arsenates Arsenic compounds, liquid, n.o.s. inorganic, including
n.o.s.; arsenites, n.o.s.; arsenic sulfides, n.o.s.; arsenates, n.o.s.; arsenites, n.o.s.; arsenic
and organic compounds of arsenic, n.o.s. sulfides, n.o.s.; and organic compounds of arsenic,
n.o.s.
Arsenic compounds, solid, n.o.s. including arsenates, Arsenic compounds, solid, n.o.s. inorganic, including
n.o.s.; arsenites, n.o.s.; arsenic sulfides, n.o.s; arsenates, n.o.s.; arsenites, n.o.s.; arsenic
and organic compounds of arsenic, n.o.s.. sulfides, n.o.s.; and organic compounds of arsenic,
n.o.s.
Barium selenate, see Selenates or Selenites............ Barium selenate, see Selenates or Selenites.
Barium selenite, see Selenates or Selenites............ Barium selenite, see Selenates or Selenites.
Battery-powered vehicle or Battery-powered equipment Battery-powered vehicle or Battery-powered equipment.
wet battery.
Boron trifluoride...................................... Boron trifluoride, compressed.
Bromotrifluoromethane, R13B1........................... Bromotrifluoromethane or Refrigerant gas, R 13B1.
Butane or Butane mixtures see also Petroleum gases, Butane see also Petroleum gases, liquefied.
liquefied.
n-Butyl methacrylate................................... n-Butyl methacrylate, inhibited.
Butylacrylate.......................................... Butyl acrylates, inhibited.
Calcium selenate, see Selenates or Selenites........... Calcium selenate, see Selenates or Selenites.
Carbon monoxide........................................ Carbon monoxide, compressed.
Carbon monoxide and hydrogen mixture................... Carbon monoxide and hydrogen mixture, compressed.
Carbonyl fluoride...................................... Carbonyl fluoride, compressed.
Cartridges, safety, blank, see Cartridges for weapons, Cartridges, safety, blank, see Cartridges for weapons,
blank (UN 0014). blank (UN 0014).
Cartridges, safety, see Cartridges for weapons, other Cartridges, safety, see Cartridges for weapons, other
than blank or Cartridges, power device (UN 0323). than blank or Cartridges, power device (UN 0323).
1-Chloro-1,1-difluoroethanes, R142b.................... 1-Chloro-1,1-difluoroethane or Refrigerant gas R142b.
1-Chloro-1,2,2,2-tetrafluoroethane, R124............... 1-Chloro-1,2,2,2-tetrafluoroethane or Refrigerant gas R
124.
1-Chloro-2,2,2-trifluoroethane, R133a.................. 1-Chloro-2,2,2-trifluoroethane or Refrigerant gas R
133a.
Chlorodifluorobromomethane, R12B1...................... Chlorodifluorobromomethane or Refrigerant gas R 12B1.
Chlorodifluoromethane and chloropentafluoroethane Chlorodifluoromethane and chloropentafluoroethane
mixture with fixed boiling point, with approximately mixture or Refrigerant gas R 502 with fixed boiling
49 percent chlorodifluoromethane, R502. point, with approximately 49 percent
chlorodifluoromethane.
Chlorodifluoromethane, R22............................. Chlorodifluoromethane or Refrigerant gas R 22.
Chloropentafluoroethane, R115.......................... Chloropentafluoroethane or Refrigerant gas R 115.
Chlorotrifluoromethane and trifluoromethane azeotropic Chlorotrifluoromethane and trifluoromethane azeotropic
mixture with approximately 60 percent mixture or Refrigerant gas R 503 with approximately 60
chlorotrifluoromethane, R503. percent chlorotrifluoromethane.
Chlorotrifluoromethane, R13............................ Chlorotrifluoromethane or Refrigerant gas R13.
Coal gas............................................... Coal gas, compressed.
Copper selenate, see Selenates or Selenites............ Copper selenate, see Selenates or Selenites.
Copper selenite, see Selenates or Selenites............ Copper selenite, see Selenates or Selenites.
Cyanogen, liquefied.................................... Cyanogen.
Cyclopropane, liquefied................................ Cyclopropane.
Deuterium.............................................. Deuterium, compressed.
Diborane............................................... Diborane, compressed.
Dichlorodifluoromethane and difluoroethane azeotropic Dichlorodifluoromethane and difluoroethane azeotropic
mixture with approximately 74 percent mixture or Refrigerant gas R 500 with approximately 74
dichlorodifluoromethane, R500. percent dichlorodifluoromethane.
Dichlorodifluoromethane, R12........................... Dichlorodifluoromethane or Refrigerant gas R 12.
Dichloroethylene....................................... 1,2-Dichloroethylene.
Dichlorofluoromethane, R21............................. Dichlorofluoromethane or Refrigerant gas R 21.
Dichlorotetrafluoroethane, R114........................ 1,2-Dichloro-1,1,2,2-Tetrafluoroethane or Refrigerant
gas R 114.
1,1-Difluoroethane, R152a.............................. 1,1-Difluoroethane or Refrigerant gas R 152a.
1,1-Difluoroethylene, R1132a........................... 1,1-Difluoroethylene or Refrigerant gas R 1132a.
Difluoromethane........................................ Difluoromethane or Refrigerant gas R 32.
Dimethylaminoethyl methacrylate........................ 2-Dimethylaminoethyl methacrylate.
Dinitrogen tetroxide, liquefied........................ Dinitrogen tetroxide.
Dipropyl ether......................................... Di-n-propyl ether.
Disodium trioxosilicate, pentahydrate.................. Disodium trioxosilicate.
Ethane, compressed..................................... Ethane.
Ethyl fluoride......................................... Ethyl fluoride or Refrigerant gas R 161.
Ethylene, acetylene and propylene in mixtures, Ethylene, acetylene and propylene mixture, refrigerated
refrigerated liquid with at least 71.5 percent liquid with at least 71.5 percent ethylene with not
ethylene with not more than 22.5 percent acetylene and more than 22.5 percent acetylene and not more than 6
not more than 6 percent propylene. percent propylene.
[[Page 24715]]
Flammable gas in lighters, see Lighters or lighter Flammable gas in lighters, see Lighters or Lighter
refills, containing flammable gas. refills, cigarettes, containing flammable gas.
Fuse, instantaneous, non-detonating or Quickmatch...... Fuse, non-detonating (instantaneous or quickmatch).
Heptafluoropropane..................................... Heptafluoropropane or Refrigerant gas R 227.
Hexafluoroethane, R1116................................ Hexafluoroethane, compressed or Refrigerant gas R 116.
Hexafluoropropylene, R1216............................. Hexafluoropropylene, compressed or Refrigerant gas R
1216.
Hydriotic acid, solution............................... Hydriotic acid.
Hydrobromic acid solution, with more than 49 percent Hydrobromic acid, with more than 49 percent hydrobromic
hydrobromic acid (PG II and III). acid (PG II and III).
Hydrobromic acid solution, with not more than 49 Hydrobromic acid, with not more than 49 percent
percent hydrobromic acid (PG II and III). hydrobromic acid (PG II and III).
Hydrocarbon gases, compressed, n.o.s. or Hydrocarbon Hydrocarbon gas mixture, compressed, n.o.s.
gases mixtures, compressed, n.o.s.
Hydrocarbon gases, liquefied, n.o.s. or Hydrocarbon Hydrocarbon gas mixture, liquefied, n.o.s.
gases mixtures, liquefied, n.o.s.
Hydrochloric acid, solution............................ Hydrochloric acid.
Hydrofluoric acid solution, with more than 60 percent Hydrofluoric acid, with more than 60 percent strength.
strength.
Hydrofluoric acid solution, with not more than 60 Hydrofluoric acid, with not more than 60 percent
percent strength. strength.
Hydrogen sulfide, liquefied............................ Hydrogen sulfide.
Isobutane or Isobutane mixtures see also Petroleum Isobutane see also Petroleum gases, liquefied.
gases, liquefied.
Isobutyl acrylate...................................... Isobutyl acrylate, inhibited.
Isobutyl methacrylate.................................. Isobutyl methacrylate, inhibited.
Isopentane, see Pentane................................ Isopentane, see Pentane.
Jet thrust unit (Jato), see Rocket motors.............. Jet thrust unit (Jato), see Rocket motors.
Magnesium bisulfite solution, see Bisulfites, aqueous Magnesium bisulfite solution, see Bisulfites, aqueous
solutions, n.o.s. solutions, n.o.s.
Mercury iodide......................................... Mercury iodide, solid.
Methacrylaldehyde...................................... Methacrylaldehyde, inhibited.
Methanol or Methyl alcohol (both entries).............. Methanol (both entries).
Methyl alcohol, see Methanol........................... Methyl alcohol see Methanol.
Methyl chloride........................................ Methyl chloride or Refrigerant gas R 40.
Methyl fluoride........................................ Methyl fluoride or Refrigerant gas R 41.
Methylmorpholine....................................... 4-Methylmorpholine or n-methylmorpholine.
Nitric oxide........................................... Nitric oxide, compressed.
Nitrogen dioxide, liquefied see Dinitrogen tetroxide, Nitrogen dioxide see Dinitrogen tetroxide.
liquefied.
Nitrogen trifluoride (both entries).................... Nitrogen trifluoride, compressed.
Nitrous oxide, compressed.............................. Nitrous oxide.
2,5-Norbornadiene or Dicycloheptadiene................. 2,5-Norbornadiene or Bicyclo[2,2,1]hepta-2,5-diene,
inhibited.
Octafluorobut-2-ene.................................... Octafluorobut-2-ene or Refrigerant gas R 1318.
Octafluorocyclobutane, RC318........................... Octafluorocyclobutane or Refrigerant gas R C318.
Octafluoropropane, R218................................ Octafluoropropane or Refrigerant gas R 218.
Oil gas................................................ Oil gas, compressed.
Oxygen difluoride...................................... Oxygen difluoride, compressed.
Pentafluoroethane...................................... Pentafluoroethane or Refrigerant gas R 125.
Perfluoroethyl vinyl ether............................. Perfluoro(ethyl vinyl ether).
Perfluoromethyl vinyl ether............................ Perfluoro(methyl vinyl ether).
Phosphorus pentafluoride............................... Phosphorus pentafluoride, compressed.
Polyalkylamines, n.o.s., see Amines, etc............... Polyalkylamines, n.o.s., see Amines, etc.
Potassium bisulfite solution, see Bisulfites, Potassium bisulfite solution, see Bisulfites,
inorganic, aqueous solutions, n.o.s. inorganic, aqueous solutions, n.o.s.
Potassium selenate, see Selenates or Selenites......... Potassium selenate, see Selenates or Selenites.
Potassium selenite, see Selenates or Selenites......... Potassium selenite, see Selenates or Selenites.
Propane or Propane mixtures see also Petroleum gases, Propane see also Petroleum gases, liquefied.
liquefied.
Rare gases and nitrogen mixtures....................... Rare gases and nitrogen mixtures, compressed.
Rare gases and oxygen mixtures......................... Rare gases and oxygen mixtures, compressed.
Rare gases, mixtures................................... Rare gases mixtures, compressed.
Receptacles, small, containing gas flammable, without Receptacles, small, containing gas (gas cartridges)
release device, not refillable and not exceeding 1 L flammable, without release device, not refillable and
capacity. not exceeding 1 L capacity.
Receptacles, small, containing gas non-flammable, Receptacles, small, containing gas (gas cartridges)
without release device, not refillable and not nonflammable, without release device, not refillable
exceeding 1 L capacity. and not exceeding 1 L capacity.
Refrigerating machines, containing non-flammable, non- Refrigerating machines, containing non-flammable, non-
toxic, liquefied gas or ammonia solutions (UN2073). toxic, liquefied gas or ammonia solution (UN2672).
Silane................................................. Silane, compressed.
Silicon tetrafluoride.................................. Silicon tetrafluoride, compressed.
Sodium hydrogendifluoride.............................. Sodium hydrogendifluoride, solid.
Steel swarf, see Ferrous metal borings, etc............ Steel swarf, see Ferrous metal borings, etc.
Sulfur dioxide, liquefied.............................. Sulfur dioxide.
Sulfur trioxide, inhibited............................. Sulfur trioxide, inhibited or Sulfur trioxide,
stabilized.
1,1,1,2-Tetrafluoroethane.............................. 1,1,1,2-Tetrafluoroethane or Refrigerant gas R 134a.
Tetrafluoromethane, R14................................ Tetrafluoromethane, compressed or Refrigerant gas R 14.
Toluene sulfonic acid, see Alkyl, or Aryl sulfonic acid Toluene sulfonic acid, see Alkyl, or Aryl sulfonic acid
etc. etc.
Trifluoroethane, compressed, R143...................... 1,1,1-Trifluoroethane, compressed or Refrigerant gas R
143a.
Trifluoromethane....................................... Trifluoromethane or Refrigerant gas R 23.
Vinyl toluene, inhibited, mixed isomers................ Vinyltoluenes, inhibited.
Vinyltrichlorosilane................................... Vinyltrichlorosilane, inhibited.
[[Page 24716]]
Xenon.................................................. Xenon, compressed.
Zinc bisulfite solution, see Bisulfites, inorganic Zinc bisulfite solution, see Bisulfites, aqueous
aqueous solutions, n.o.s. solutions, n.o.s.
Zinc selenate, see Selenates or Selenites.............. Zinc selenate, see Selenates or Selenites.
Zinc selenite, see Selenates or Selenites.............. Zinc selenite, see Selenates or Selenites.
----------------------------------------------------------------------------------------------------------------
16-2. For the entry ``Mercury contained in manufactured articles'',
in Column (5), the PG designation ``I'' is revised to read ``III''.
16-3. For the following entries, Column (6) is revised as follows:
------------------------------------------------------------------------
Revise to
Column (2) entry Column (6) entry read:
------------------------------------------------------------------------
Allyl isothiocyanate, 6.1....................... 6.1, 3
stabilized.
Bromoacetone................. 6.1....................... 6.1, 3
n-Butyl chloroformate........ 6.1, 8.................... 6.1, 8, 3
Cyclobutyl chloroformate..... 6.1, 8.................... 6.1, 8, 3
Epibromohydrin............... 6.1....................... 6.1, 3
Epichlorohydrin.............. 6.1....................... 6.1, 3
Ethyl bromoacetate........... 6.1....................... 6.1, 3
Ethyl chloroacetate.......... 6.1....................... 6.1, 3
Isocyanatobenzotrifluorides.. 6.1....................... 6.1, 3
Propylene chlorohydrin....... 6.1....................... 6.1, 3
Trifluoroacetyl chloride..... 2.3....................... 2.3, 8
------------------------------------------------------------------------
16-4. For the following entries, Column (7) is revised as follows:
----------------------------------------------------------------------------------------------------------------
Column (2) entry Column (7) entry Revise to read:
----------------------------------------------------------------------------------------------------------------
Alkali metal alcoholates, self- ................................... 64
heating, corrosive, n.o.s. (PG II and
III).
Alkaline earth metal alcoholates, ................................... 65
n.o.s. (PG II and III).
Benzaldehyde.......................... ................................... T1
Corrosive liquids, toxic, n.o.s. (PG A7, B10............................ A7, B10, T18, T27
I).
Corrosive liquids, toxic, n.o.s. (PG B3................................. B3, T18, T26
II).
Corrosive liquids, toxic, n.o.s. (PG ................................... T8
III).
Corrosive solids, n.o.s. (PG II and ................................... 128
III).
Corrosive solids, water-reactive, B105............................... 128, B105
n.o.s. (PG II).
Environmentally hazardous substances, 8, N50, T1......................... 8, T1
liquid, n.o.s.
Environmentally hazardous substances, 8, N50, B54........................ 8, B54
solid, n.o.s.
Explosive, blasting, type C........... ................................... 123
Ferrocerium........................... A19................................ 59, A19
Isosorbide-5-mononitrate.............. ................................... 66
Maneb or Maneb preparations with not A1, A19, B105...................... 57, A1, A19, B105
less than 60 percent maneb.
Methacrylic acid, inhibited........... T8................................. T8, T47
Nitrates, inorganic, aqueous solution, T8................................. 58, T8
n.o.s. (PG II and III).
Nitroglycerin, desensitized with not ................................... 125
less than 40 percent non-volatile
water insoluble phlegmatizer, by mass.
Organophosphorus pesticides, liquid, ................................... T42
flammable, toxic, flash point less
than 23 degrees C (PG I).
Organophosphorus pesticides, liquid, ................................... T18
flammable, toxic, flash point less
than 23 degrees C (PG II).
Oxidizing liquid, n.o.s. (PG II and A2................................ 127, A2
III).
Pentaerythrite tetranitrate or ................................... 120
Pentaerythritol tetranitrate, or
PETN, with not less than 7 percent
wax by mass.
Pentaerythrite tetranitrate, wetted or ................................... 121
Pentaerythritol tetranitrate, wetted
or PETN, wetted with not less than 25
percent water, by mass, or
Pentaerythrite tetranitrate, or
Pentaerythritol tetranitrate or PETN,
desensitized with not less than 15
percent phlegmatizer by mass.
Polyester resin kit................... 40................................. None
Sulfur (UN1350)....................... A1, N20, T1........................ 30, A1, N20, T1
Urea nitrate dry or wetted with less ................................... 119
than 20 percent water, by mass.
Water-reactive solid, corrosive, B101, B106......................... 128, B101, B106
n.o.s. (PG II).
Water-reactive solid, corrosive, B105, B106......................... 128, B105, B106
n.o.s. (PG III).
----------------------------------------------------------------------------------------------------------------
16-5. For the following entries, Columns (8A), (8B), or (8C) are
revised as follows:
------------------------------------------------------------------------
Column (2) entry Column (8A) entry Revise to read:
------------------------------------------------------------------------
Polyester resin kit........... None 152
Sulfur (UN1350)............... 151 None
Column (8B) entry Revise to read:
Sulfur (UN1350)............... 213 None
Column (8C) entry Revise to read:
Metal catalyst, dry (PG II)... None 242
[[Page 24717]]
Metal catalyst, dry (PG III).. None 241
------------------------------------------------------------------------
16-6. For the following entries, Column (9A) is revised as follows:
------------------------------------------------------------------------
Column (2) entry Column (9A) entry Revise to read:
------------------------------------------------------------------------
Cyclohexyl isocyanate......... 5 L.................. Forbidden.
Divinyl ether, inhibited...... 5 L.................. 1 L.
Potassium..................... 1 kg................. Forbidden.
Potassium, metal alloys....... 1 kg................. Forbidden.
Sodium........................ 1 kg................. Forbidden.
------------------------------------------------------------------------
16-7. For the following entries, Column (9B) is revised as follows:
------------------------------------------------------------------------
Column (2) entry Column (9B) entry Revise to read:
------------------------------------------------------------------------
Cyclohexyl isocyanate......... 60 L................. Forbidden.
Ethyl isocyanate.............. 30 L................. Forbidden.
Ethylene oxide and carbon 75 kg................ 25 kg.
dioxide mixture with more
than 87 percent ethylene
oxide.
Hexafluoroacetone............. 25 kg................ Forbidden.
Isobutyl isocyanate........... 60 L................. Forbidden.
Isopropyl isocyanate.......... 30 L................. Forbidden.
Methoxymethyl isocyanate...... 30 L................. Forbidden.
Oil gas....................... 150 kg............... 25 kg.
Silicon tetrafluoride......... 25 kg................ Forbidden.
Sulfur tetrafluoride.......... 25 kg................ Forbidden.
Toxic liquids, oxidizing, 2.5 L................ Forbidden.
n.o.s. Inhalation hazard,
Packing Group I, Zone A.
------------------------------------------------------------------------
16-8. In Column (10A), for the entry ``Battery-powered vehicle or
Battery-powered equipment wet battery'', the ``A'' is removed.
17. In Appendix B to Sec. 172.101, the List of Marine Pollutants is
amended by adding the following materials in appropriate alphabetical
order:
Appendix B to Sec. 172.101--List of Marine Pollutants
* * * * *
------------------------------------------------------------------------
S.M.P (1) Marine pollutant (2)
------------------------------------------------------------------------
[ADD:]
* * * * *
Acetaldehyde.
Alkyl (C10-C21) sulphonic acid ester
of phenol.
Anisole.
Azinphos-methyl.
Benzaldehyde.
N,N-Bis (2-hydroxyethyl) oleamide
(LOA).
Bromobenzene.
Butanedione.
Butyl mercaptans.
N-tert-butyl-N-cyclopropyl-6-
methylthio-1,3,5-triazine-2,4-
diamine.
Butyraldehyde.
Camphor oil.
Coconitrile.
PP................................ Cymenes (o-;m-;p-).
normal-Decaldehyde.
normal-Decanol.
1,3-Dibromobenzene.
Di-normal-butyl ketone.
Dimethyl disulphide.
Dimethylhydrazine, symmetrical.
Dimethylhydrazine, unsymmetrical.
Dipentene.
2,4-Di-tert-butylphenol.
2,6-Di-tert-butylphenol.
Diphenyl ether/biphenyl phenyl ether
mixtures.
Diphenyl/diphenyl ether (mixtures).
EPTC (ISO).
2-Ethylhexaldehyde
2-Ethylbutyraldehyde
Furathiocarb (ISO).
PP................................ normal-Heptyl aldehyde.
2,4-Hexadiene aldehyde.
normal-Hexaldehyde.
Hydrogen cyanide solution in
alcohol, with not more than 45%
hydrogen cyanide.
Hydrogen cyanide, stabilized with
less than 3% water.
Hydrogen cyanide, stabilized with
less than 3% water and absorbed in
a porous inert material.
Iron sponge, spent.
Isooctanol.
Isodecaldehyde.
Isodecanol.
Isononanol.
Isotetramethylbenzene.
Isovaleraldehyde.
Mancozeb (ISO).
2-Methylbutyraldehyde.
Nitrobenzene.
1-Nonanal.
1-Nonanol.
normal-Octaldehyde.
1-Octanol.
Phenylcyclohexane.
Propionaldehyde.
Tallow nitrile.
Tetrabromoethane.
Tetrachloroethylene.
4-Thiapentanal.
Triphenylphosphate.
1-Undecanol.
normal-Valeraldehyde.
* * * * *
------------------------------------------------------------------------
Sec. 172.101, Appendix B [Amended]
18. In addition, in Appendix B to Sec. 172.101, the List of Marine
Pollutants is amended as follows:
a. The entry ``Azenphos-methyl'' is removed.
b. For the entry ``Chlorinated paraffins (C10-C13)'', the
designation ``PP'' is added in Column (1).
c. The entry ``Mononitrobenzene (nitro benzene)'' is removed.
d. The entry ``1,1,2,2-Tetrabromoethane'' is removed.
e. The entry ``1,1,2,2-Tetrachloroethylene'' is removed.
f. The designation ``PP'' is added in column (1) for the following
materials:
Copper chloride solution
Cupric sulfate
Esfenvalerate
Fenbutatin oxide
1,3-Hexachlorobutadiene
[[Page 24718]]
Quizalofop
Quizalofop-p-ethyl
Tetrachlorovinfos
Tetraethyl lead, liquid
Tricresyl phosphate with more than 3 per cent ortho isomer
g. The following entries are removed:
Acetylene dibromide
Arsenates, liquid, n.o.s.
Arsenates, solid, n.o.s.
Arsenic bromide
Arsenic chloride
Arsenical pesticides liquid, toxic, flammable, n.o.s.
Biphenyl phenyl ether and diphenyl oxide, mixtures
1-Butanethiol
Carbon bisulphide
Chlorobenzylchlorides
alpha-Chloropropylene
1-Chloropropylene
2-Chloropropylene
Chromyl chloride
Copper arsentate
1,2-Dibromethene
1,2-Dibromoethane
o-Dichlorobenzene
p-Dichlorobenzene
Dichloroether
Dichloroethyl oxide
Dimethylarsinic acid
Ethylene chloride
Ethylene dichloride
Ethylidene dichloride
Hydrogen cyanide, anhydrous, stabilized
Hydrogen cyanide, anhydrous, stabilized absorbed in a porous inert
material
Isopropyltoluene
Maneb or Maneb preparations with not less than 60% maneb
Mercuric sulphide
Mercury iodide, solution
Metaarsenic acid
3-Methylpyridine
Methylchloroform
Methylene bromide
Methylene dibromide
Naptha, coal tar
Nitrates, inorganic, n.o.s.
Nitrites, inorganic, n.o.s.
Potassium dihydrogen arsenate
Propenyl chloride (cis-; trans-)
Propylene dichloride
Propylidene dichloride
Sodium metaarsenite
Sodium orthoarsenate
Strontium orthoarsenite
Turpentine substitute
White arsenic
19. In Sec. 172.102, in paragraph (c)(1), Special Provisions 40 and
45 are removed, Special Provisions 15, 30 and 32 are revised, the last
sentence of Special Provision 38 is revised, a sentence is added at the
end of Special Provisions 23, 43 and 47, a sentence is added at the
beginning of Special Provision 102, Special Provisions 57, 58, 59, 64,
65, 66, 74, 77, 118, 119, 120, 121, 123, 125, 127 and 128 are added; in
paragraph (c)(3), the first sentence of Special Provision B5 is revised
and Special Provision B115 is added; in paragraph (c)(5) Special
Provision N50 is removed; and in paragraph (c)(7)(ii), Special
Provision T47 is added, to read as follows:
Sec. 172.102 Special provisions.
* * * * *
(c) * * *
(1) * * *
* * * * *
15. Chemical kits and first aid kits are boxes, cases, etc.,
containing small amounts of various compatible dangerous goods which
are used for medical, analytical, or testing purposes and for which
exceptions are provided in this subchapter. For transportation by
aircraft, any hazardous materials forbidden in passenger aircraft
may not be included in these kits. Inner packagings may not exceed
250 mL for liquids or 250 g for solids and must be protected from
other materials in the kit. The total quantity of hazardous
materials in any one kit may not exceed either 1 L or 1 kg. The
packing group assigned to the kit as a whole must be the most
stringent packing group assigned to any individual substance
contained in the kit. Kits must be packed in wooden boxes (4C1,
4C2), plywood boxes (4D), reconstituted wood boxes (4F), fiberboard
boxes (4G) or plastic boxes (4H1, 4H2); these packagings must meet
the requirements appropriate to the packing group assigned to the
kit as a whole. The total quantity of hazardous materials in any one
package may not exceed either 10 L or 10 kg. Kits which are carried
on board transport vehicles for first-aid or operating purposes are
not subject to the requirements of this subchapter.
* * * * *
23. * * * Quantities of not more than 500 g per package with not
less than 10 percent water by mass may also be classed in Division
4.1, provided a negative test result is obtained when tested in
accordance with test series 6(c) of the UN Manual of Tests and
Criteria.
* * * * *
30. Sulfur is not subject to the requirements of this subchapter
if transported in a non-bulk packaging or if formed to a specific
shape (e.g., prills, granules, pellets, pastilles, or flakes).
* * * * *
32. Polymeric beads and molding compounds may be made from
polystyrene, poly(methyl methacrylate) or other polymeric material.
* * * * *
38. * * * If the SADT of the technically pure substance is
higher than 75 deg.C, the technically pure substance and
formulations derived from it are not self-reactive materials and, if
not meeting any other hazard class, are not subject to the
requirements of this subchapter.
* * * * *
43. * * * Packagings should be so constructed that explosion is
not possible by reason of increased internal pressure.
* * * * *
47. * * * Small inner packagings consisting of sealed packets
containing less than 10 ml of a Class 3 liquid in Packing Group II
or III absorbed onto a solid material are not subject to this
subchapter provided there is no free liquid in the packet.
* * * * *
57. Maneb or Maneb preparations stabilized against self-heating
need not be classified in Division 4.2 when it can be demonstrated
by testing that a volume of 1 m3 of substance does not
self-ignite and that the temperature at the center of the sample
does not exceed 200 deg.C, when the sample is maintained at a
temperature of not less than 75 deg.C 2 deg.C for a
period of 24 hours, in accordance with procedures set forth for
testing self-heating materials in the UN Manual of Tests and
Criteria.
58. Aqueous solutions of Division 5.1 inorganic solid nitrate
substances are considered as not meeting the criteria of Division
5.1 if the concentration of the substances in solution at the
minimum temperature encountered in transport is not greater than 80%
of the saturation limit.
59. Ferrocerium, stabilized against corrosion, with a minimum
iron content of 10 percent is not subject to the requirements of
this subchapter.
64. The group of alkali metals includes lithium, sodium,
potassium, rubidium, and caesium.
65. The group of alkaline earth metals includes magnesium,
calcium, strontium, and barium.
66. Formulations of these substances containing not less than 30
percent non-volatile, non-flammable phlegmatizer are not subject to
this subchapter.
* * * * *
74. During transport, this material must be protected from
direct sunshine and stored or kept in a cool and well-ventilated
place, away from all sources of heat.
77. For domestic transportation, a Division 5.1 subsidiary risk
label is required only if a carbon dioxide and oxygen mixture
contains more than 23.5% oxygen.
* * * * *
102. The ends of the detonating cord must be tied fast so that the
explosive cannot escape. * * *
* * * * *
118. This substance may not be transported under the provisions
of Division 4.1 unless specifically authorized by the Associate
Administrator for Hazardous Materials Safety.
119. This substance, when in quantities of not more than 11.5 kg
(25.3 pounds), with not less than 10 percent water, by mass, also
may be classed in Division 4.1, provided a negative test result is
obtained when tested in accordance with test series 6(c) of the UN
Manual of Tests and Criteria.
120. The phlegmatized substance must be significantly less
sensitive than dry PETN.
[[Page 24719]]
121. This substance, when containing less alcohol, water or
phlegmatizer than specified, may not be transported unless approved
by the Associate Administrator for Hazardous Materials Safety.
123. Any explosives, blasting, type C containing chlorates must
be segregated from explosives containing ammonium nitrate or other
ammonium salts.
125. Lactose or glucose or similar materials may be used as a
phlegmatizer provided that the substance contains not less than 90%,
by mass, of phlegmatizer. These mixtures may be classified in
Division 4.1 when tested in accordance with test series 6(c) of the
UN Manual of Tests and Criteria and approved by the Associate
Administrator for Hazardous Materials Safety. Testing must be
conducted on at least three packages as prepared for transport.
Mixtures containing at least 90%, by mass, of phlegmatizer are not
subject to the requirements of this subchapter. Packages containing
mixtures with not less than 98% by mass, of phlegmatizer need not
bear a POISON subsidiary risk label.
127. Mixtures containing oxidizing and organic materials
transported under this entry may not meet the definition and
criteria of a Class 1 material. (See Sec. 173.50 of this
subchapter.)
128. Notwithstanding the provisions of Sec. 172.101(c)(12), an
aluminum smelting by-product or aluminum remelting by-product
described under this entry, in Packing Group II or III, may be
packaged in accordance with Special Provision B115 of this section.
* * * * *
(3) * * *
* * * * *
B5. Only ammonium nitrate solutions with 35 percent or less
water that will remain completely in solution under all conditions
of transport at a maximum lading temperature of 116 deg.C
(240 deg.F) are authorized for transport in the following bulk
packagings: MC 307, MC 312, DOT 407 and DOT 412 cargo tanks with at
least 172 kPa (25 psig) design pressure. * * *
* * * * *
B115. Rail cars, highway trailers, roll-on/roll-off bins, or
other non-specification bulk packagings are authorized. Packagings
must be sift-proof, prevent liquid water from reaching the hazardous
material, and be provided with sufficient venting to preclude
dangerous accumulation of flammable, corrosive, or toxic gaseous
emissions such as methane, hydrogen, and ammonia. The material must
be loaded dry.
* * * * *
(7) * * *
(ii) * * *
T47. Temperature must be maintained between 18 deg.C
(64.4 deg.F) and 40 deg.C (104 deg.F) when carried in tanks. Tanks
containing solidified methyacrylic acid may not be reheated during
transport.
* * * * *
Sec. 172.102 [Amended]
20. In addition, in Sec. 172.102, in paragraph (c)(1), in special
provisions 38 and 46, in the first sentence of each special provision,
the wording ``OP6B'' is revised to read ``OP6'' each place it appears.
21. In Sec. 172.203, paragraph (j) is removed and reserved and
paragraph (k)(3) is amended by adding 14 new entries in appropriate
alphabetical order to the list of proper shipping names, to read as
follows:
Sec. 172.203 Additional description requirements.
* * * * *
(k) * * *
(3) * * *
Compressed gas, toxic, corrosive, n.o.s.
Compressed gas, toxic, flammable, corrosive, n.o.s.
Compressed gas, toxic, oxidizing, corrosive, n.o.s.
Compressed gas, toxic, oxidizing, n.o.s.
* * * * *
Gas, refrigerated liquid, flammable, n.o.s.
Gas, refrigerated liquid, oxidizing, n.o.s.
* * * * *
Hydrocarbon gases, compressed, n.o.s.
Hydrocarbon gases, liquefied, n.o.s.
Hydrogen gases mixtures, compressed, n.o.s.
Hydrocarbon gases mixtures, liquefied, n.o.s.
* * * * *
Liquefied gas, toxic, corrosive, n.o.s.
Liquefied gas, toxic, flammable, corrosive, n.o.s.
Liquefied gas, toxic, oxidizing, corrosive, n.o.s.
Liquefied gas, toxic, oxidizing, n.o.s.
* * * * *
Organometallic compound, water reactive, flammable, n.o.s.
* * * * *
Sec. 172.203 [Amended]
22. In addition, in Sec. 172.203, in paragraph (m)(3), in the first
sentence, the wording ``or `Toxic-Inhalation Hazard' '' is added
immediately following `` `Poison-Inhalation Hazard' ''; and in the
second sentence the wording `` `Poison' '' is revised to read ``
`Poison' or `Toxic' ''.
PART 173--SHIPPERS--GENERAL REQUIREMENTS FOR SHIPMENTS AND
PACKAGINGS
23. The authority citation for part 173 continues to read as
follows:
Authority: 49 U.S.C. 5101-5127; 49 CFR 1.53.
24. In Sec. 173.3, paragraph (c)(3) is revised and a new paragraph
(c)(7) is added, to read as follows:
Sec. 173.3 Packaging and exceptions.
* * * * *
(c) * * *
(3) Each salvage packaging must be marked with the proper shipping
name of the hazardous material inside the packaging and the name and
address of the consignee. In addition, the packaging must be marked
``SALVAGE'' or ``SALVAGE DRUM''.
* * * * *
(7) A salvage packaging marked ``T'' in accordance with applicable
provisions in the UN Recommendations may be used.
Sec. 173.3 [Amended]
25. In addition, in Sec. 173.3, in paragraph (c)(1), at the
beginning of the paragraph, the wording ``The drum'' is revised to read
``Except as provided in paragraph (c)(7) of this section, the drum''.
26. In Sec. 173.21, the last sentence in paragraph (f) introductory
text is revised to read as follows:
Sec. 173.21 Forbidden materials and packages.
* * * * *
(f) * * * The SADT may be determined by any of the test methods
described in Part II of the UN Manual of Tests and Criteria.
* * * * *
Sec. 173.32c [Amended]
27. In Sec. 173.32c, in paragraph (j), the wording ``5,000 liters
(1,900 gallons)'' is revised to read ``7,500 L''.
Sec. 173.34 [Amended] 27a.
In Sec. 173.34, in the table in paragraph (e)(18)(i), under the
column heading ``Porous filler requalification'', under ``Initial'',
the year ``2001'' is revised to read ``2011''.
28. Section 173.60 is revised to read as follows:
Sec. 173.60 General packaging requirements for explosives.
(a) Unless otherwise provided in this subpart and in Sec. 173.7(a),
packaging used for Class 1 (explosives) materials must meet Packing
Group II requirements. Each packaging used for an explosive must be
capable of meeting the test requirements of subpart M of part 178 of
this subchapter, at the specified level of performance, and the
applicable general packaging requirements of paragraph (b) of this
section.
(b) The general requirements for packaging of explosives are as
follows:
(1) Nails, staples, and other closure devices, made of metal,
having no protective covering may not penetrate to the inside of the
outer packaging unless the inner packaging adequately protects the
explosive against contact with the metal.
(2) The closure device of containers for liquid explosives must
provide double protection against leakage, such as a screw cap secured
in place with tape.
[[Page 24720]]
(3) Inner packagings, fittings, and cushioning materials, and the
placing of explosive substances or articles in packages, must be such
that the explosive substance is prevented from becoming loose in the
outer packaging during transportation. Metallic components of articles
must be prevented from making contact with metal packagings. Articles
containing explosive substances not enclosed in an outer casing must be
separated from each other in order to prevent friction and impact.
Padding, trays, partitioning in the inner or outer packaging, molded
plastics or receptacles may be used for this purpose.
(4) When the packaging includes water that could freeze during
transportation, a sufficient amount of anti-freeze, such as denatured
ethyl alcohol, must be added to the water to prevent freezing. If the
anti-freeze creates a fire hazard, it may not be used. When a
percentage of water in the substance is specified, the combined weight
of water and anti-freeze may be substituted.
(5) If an article is fitted with its own means of ignition or
initiation, it must be effectively protected from accidental actuation
during normal conditions of transportation.
(6) The entry of explosive substances into the recesses of double-
seamed metal packagings must be prevented.
(7) The closure device of a metal drum must include a suitable
gasket; if the closure device includes metal-to-metal screw-threads,
the ingress of explosive substances into the threading must be
prevented.
(8) Whenever loose explosive substances or the explosive substance
of an uncased or partly cased article may come into contact with the
inner surface of metal packagings (1A2, 1B2, 4A, 4B and metal
receptacles), the metal packaging should be provided with an inner
liner or coating.
(9) Packagings must be made of materials compatible with, and
impermeable to, the explosives contained in the package, so that
neither interaction between the explosives and the packaging materials,
nor leakage, causes the explosive to become unsafe in transportation,
or the hazard division or compatibility group to change (see
Sec. 173.24(e)(2)).
(10) An explosive article containing an electrical means of
initiation that is sensitive to external electromagnetic radiation,
must have its means of initiation effectively protected from
electromagnetic radiation sources (for example, radar or radio
transmitters) through either design of the packaging or of the article,
or both.
(11) Plastic packagings may not be able to generate or accumulate
sufficient static electricity to cause the packaged explosive
substances or articles to initiate, ignite or inadvertently function.
Metal packagings must be compatible with the explosive substance they
contain.
(12) Explosive substances may not be packed in inner or outer
packagings where the differences in internal and external pressures,
due to thermal or other effects, could cause an explosion or rupture of
the package.
(13) Packagings for water soluble substances must be water
resistant. Packagings for desensitized or phlegmatized substances must
be closed to prevent changes in concentration during transport. When
containing less alcohol, water, or phlegmatizer than specified in its
proper shipping description, the substance is a ``forbidden'' material.
29. Section 173.62 is revised to read as follows:
Sec. 173.62 Specific packaging requirements for explosives.
(a) Except as provided in paragraph (e) of this section, when the
Sec. 172.101 Table specifies that an explosive must be packaged in
accordance with this section, only non-bulk packagings which conform to
the provisions of paragraphs (b), (c) and (d) of this section and the
applicable requirements in Secs. 173.60 and 173.61 may be used unless
otherwise approved by the Associate Administrator. Intermediate bulk
packagings may be used for explosives assigned to Packing Instruction
117 in paragraph (b) of this section. Intermediate bulk packagings must
conform with the requirements of this subchapter.
(b) Explosives Table. The Explosives Table specifies the Packing
Instructions assigned to each explosive. Explosives are identified in
the first column in numerical sequence by their identification number
(ID #), which is listed in column 4 of the Sec. 172.101 Table, of this
subchapter. The second column of the Explosives Table specifies the
Packing Instruction (PI) which must be used for packaging the
explosive. The Explosives Packing Method Table in paragraph (c) of this
section defines the methods of packaging. The Packing Instructions are
identified using a 3 digit designation. The Packing Instruction
prefixed by the letters ``US'' is particular to the United States and
not found in applicable international regulations.
Explosives Table
------------------------------------------------------------------------
ID# PI
------------------------------------------------------------------------
UN0004.............................. 112
UN0005.............................. 130
UN0006.............................. 130
UN0007.............................. 130
UN0009.............................. 130
UN0010.............................. 130
UN0012.............................. 130
UN0014.............................. 130
UN0015.............................. 130
UN0016.............................. 130
UN0018.............................. 130
UN0019.............................. 130
UN0020.............................. 101
UN0021.............................. 101
UN0027.............................. 113
UN0028.............................. 113
UN0029.............................. 131
UN0030.............................. 131
UN0033.............................. 130
UN0034.............................. 130
UN0035.............................. 130
UN0037.............................. 130
UN0038.............................. 130
UN0039.............................. 130
UN0042.............................. 132
UN0043.............................. 133
UN0044.............................. 133
UN0048.............................. 130
UN0049.............................. 135
UN0050.............................. 135
UN0054.............................. 135
UN0055.............................. 136
UN0056.............................. 130
UN0059.............................. 137
UN0060.............................. 132
UN0065.............................. 139
UN0066.............................. 140
UN0070.............................. 134
UN0072.............................. 112(a)
UN0073.............................. 133
UN0074.............................. 110(a) or 110(b)
UN0075.............................. 115
UN0076.............................. 112
UN0077.............................. 114(a) or 114(b)
UN0078.............................. 112
UN0079.............................. 112(b) or 112(c)
UN0081.............................. 116
UN0082.............................. 116 or 117
UN0083.............................. 116
UN0084.............................. 116
UN0092.............................. 135
UN0093.............................. 135
UN0094.............................. 113
UN0099.............................. 134
UN0101.............................. 140
UN0102.............................. 139
UN0103.............................. 140
UN0104.............................. 139
UN0105.............................. 140
UN0106.............................. 141
UN0107.............................. 141
UN0110.............................. 141
UN0113.............................. 110(a) or 110(b)
UN0114.............................. 110(a) or 110(b)
UN0118.............................. 112
UN0121.............................. 142
UN0124.............................. US1
UN0129.............................. 110(a) or 110(b)
UN0130.............................. 110(a) or 110(b)
UN0131.............................. 142
UN0132.............................. 114(b)
UN0133.............................. 112(a)
[[Page 24721]]
UN0135.............................. 110(a) or 110(b)
UN0136.............................. 130
UN0137.............................. 130
UN0138.............................. 130
UN0143.............................. 115
UN0144.............................. 115
UN0146.............................. 112
UN0147.............................. 112(b)
UN0150.............................. 112(a) or 112(b)
UN0151.............................. 112
UN0153.............................. 112(b) or 112(c)
UN0154.............................. 112
UN0155.............................. 112(b) or 112(c)
UN0159.............................. 111
UN0160.............................. 114(b)
UN0161.............................. 114(b)
UN0167.............................. 130
UN0168.............................. 130
UN0169.............................. 130
UN0171.............................. 130
UN0173.............................. 134
UN0174.............................. 134
UN0180.............................. 130
UN0181.............................. 130
UN0182.............................. 130
UN0183.............................. 130
UN0186.............................. 130
UN0190.............................. 101
UN0191.............................. 135
UN0192.............................. 135
UN0193.............................. 135
UN0194.............................. 135
UN0195.............................. 135
UN0196.............................. 135
UN0197.............................. 135
UN0204.............................. 134
UN0207.............................. 112(b) or 112(c)
UN0208.............................. 112(b) or 112(c)
UN0209.............................. 112
UN0212.............................. 133
UN0213.............................. 112(b) or 112(c)
UN0214.............................. 112
UN0215.............................. 112
UN0216.............................. 112(b) or 112(c)
UN0217.............................. 112(b) or 112(c)
UN0218.............................. 112(b) or 112(c)
UN0219.............................. 112
UN0220.............................. 112
UN0221.............................. 130
UN0222.............................. 112(b) or 112(c)
UN0224.............................. 110(a) or 110(b)
UN0225.............................. 133
UN0226.............................. 112(a)
UN0234.............................. 114(a) or 114(b)
UN0235.............................. 114(a) or 114(b)
UN0236.............................. 114(a) or 114(b)
UN0237.............................. 138
UN0238.............................. 130
UN0240.............................. 130
UN0241.............................. 116 or 117
UN0242.............................. 130
UN0243.............................. 130
UN0244.............................. 130
UN0245.............................. 130
UN0246.............................. 130
UN0247.............................. 101
UN0248.............................. 144
UN0249.............................. 144
UN0250.............................. 101
UN0254.............................. 130
UN0255.............................. 131
UN0257.............................. 141
UN0266.............................. 112
UN0267.............................. 131
UN0268.............................. 133
UN0271.............................. 143
UN0272.............................. 143
UN0275.............................. 134
UN0276.............................. 134
UN0277.............................. 134
UN0278.............................. 134
UN0279.............................. 130
UN0280.............................. 130
UN0281.............................. 130
UN0282.............................. 112
UN0283.............................. 132
UN0284.............................. 141
UN0285.............................. 141
UN0286.............................. 130
UN0287.............................. 130
UN0288.............................. 138
UN0289.............................. 139
UN0290.............................. 139
UN0291.............................. 130
UN0292.............................. 141
UN0293.............................. 141
UN0294.............................. 130
UN0295.............................. 130
UN0296.............................. 134
UN0297.............................. 130
UN0299.............................. 130
UN0300.............................. 130
UN0301.............................. 130
UN0303.............................. 130
UN0305.............................. 113
UN0306.............................. 133
UN0312.............................. 135
UN0313.............................. 135
UN0314.............................. 142
UN0315.............................. 142
UN0316.............................. 141
UN0317.............................. 141
UN0318.............................. 141
UN0319.............................. 133
UN0320.............................. 133
UN0321.............................. 130
UN0322.............................. 101
UN0323.............................. 134
UN0324.............................. 130
UN0325.............................. 142
UN0326.............................. 130
UN0327.............................. 130
UN0328.............................. 130
UN0329.............................. 130
UN0330.............................. 130
UN0331.............................. 116 or 117
UN0332.............................. 116 or 117
UN0333.............................. 135
UN0334.............................. 135
UN0335.............................. 135
UN0336.............................. 135
UN0337.............................. 135
UN0338.............................. 130
UN0339.............................. 130
UN0340.............................. 112(a) or 112(b)
UN0341.............................. 112(b)
UN0342.............................. 114(a)
UN0343.............................. 111
UN0344.............................. 130
UN0345.............................. 130
UN0346.............................. 130
UN0347.............................. 130
UN0348.............................. 130
UN0349.............................. 101
UN0350.............................. 101
UN0351.............................. 101
UN0352.............................. 101
UN0353.............................. 101
UN0354.............................. 101
UN0355.............................. 101
UN0356.............................. 101
UN0357.............................. 101
UN0358.............................. 101
UN0359.............................. 101
UN0360.............................. 131
UN0361.............................. 131
UN0362.............................. 130
UN0363.............................. 130
UN0364.............................. 133
UN0365.............................. 133
UN0366.............................. 133
UN0367.............................. 141
UN0368.............................. 141
UN0369.............................. 130
UN0370.............................. 130
UN0371.............................. 130
UN0372.............................. 141
UN0373.............................. 135
UN0374.............................. 134
UN0375.............................. 134
UN0376.............................. 133
UN0377.............................. 133
UN0378.............................. 133
UN0379.............................. 136
UN0380.............................. 101
UN0381.............................. 134
UN0382.............................. 101
UN0383.............................. 101
UN0384.............................. 101
UN0385.............................. 112(b) or 112(c)
UN0386.............................. 112(b) or 112(c)
UN0387.............................. 112(b) or 112(c)
UN0388.............................. 112(b) or 112(c)
UN0389.............................. 112(b) or 112(c)
UN0390.............................. 112(b) or 112(c)
UN0391.............................. 112(a)
UN0392.............................. 112(b) or 112(c)
UN0393.............................. 112(b)
UN0394.............................. 112(a)
UN0395.............................. 101
UN0396.............................. 101
UN0397.............................. 101
UN0398.............................. 101
UN0399.............................. 101
UN0400.............................. 101
UN0401.............................. 112
UN0402.............................. 112(b) or 112(c)
UN0403.............................. 135
UN0404.............................. 135
UN0405.............................. 135
UN0406.............................. 114(b)
UN0407.............................. 114(b)
UN0408.............................. 141
UN0409.............................. 141
UN0410.............................. 141
UN0411.............................. 112(b) or 112(c)
UN0412.............................. 130
UN0413.............................. 130
UN0414.............................. 130
UN0415.............................. 143
UN0417.............................. 130
UN0418.............................. 135
UN0419.............................. 135
UN0420.............................. 135
UN0421.............................. 135
UN0424.............................. 130
[[Page 24722]]
UN0425.............................. 130
UN0426.............................. 130
UN0427.............................. 130
UN0428.............................. 135
UN0429.............................. 135
UN0430.............................. 135
UN0431.............................. 135
UN0432.............................. 135
UN0433.............................. 111
UN0434.............................. 130
UN0435.............................. 130
UN0436.............................. 130
UN0437.............................. 130
UN0438.............................. 130
UN0439.............................. 137
UN0440.............................. 137
UN0441.............................. 137
UN0442.............................. 137
UN0443.............................. 137
UN0444.............................. 137
UN0445.............................. 137
UN0446.............................. 136
UN0447.............................. 136
UN0448.............................. 114(b)
UN0449.............................. 101
UN0450.............................. 101
UN0451.............................. 130
UN0452.............................. 141
UN0453.............................. 130
UN0454.............................. 142
UN0455.............................. 131
UN0456.............................. 131
UN0457.............................. 130
UN0458.............................. 130
UN0459.............................. 130
UN0460.............................. 130
UN0461.............................. 101
UN0462.............................. 101
UN0463.............................. 101
UN0464.............................. 101
UN0465.............................. 101
UN0466.............................. 101
UN0467.............................. 101
UN0468.............................. 101
UN0469.............................. 101
UN0470.............................. 101
UN0471.............................. 101
UN0472.............................. 101
UN0473.............................. 101
UN0474.............................. 101
UN0475.............................. 101
UN0476.............................. 101
UN0477.............................. 101
UN0478.............................. 101
UN0479.............................. 101
UN0480.............................. 101
UN0481.............................. 101
UN0482.............................. 101
UN0483.............................. 112(b) or 112(c)
UN0484.............................. 112(b) or 112(c)
UN0486.............................. 101
UN0487.............................. 135
UN0488.............................. 130
UN0489.............................. 112(b) or 112(c)
UN0490.............................. 112(b) or 112(c)
UN0491.............................. 143
UN0492.............................. 135
UN0493.............................. 135
UN0494.............................. US1
UN0495.............................. 115
UN0496.............................. 112(b) or 112(c)
UN0497.............................. 115
UN0498.............................. 114(b)
UN0499.............................. 114(b)
UN0500.............................. 131
NA0124.............................. US1
NA0276.............................. 134
NA0323.............................. 134
NA0337.............................. 135
NA0349.............................. 133
NA0494.............................. US1
------------------------------------------------------------------------
(c) Explosives Packing Instruction Table. Explosives must be
packaged in accordance with the following table:
(1) The first column lists, in alphanumeric sequence, the packing
methods prescribed for explosives in the Explosives Table of paragraph
(b) of this section.
(2) The second column specifies the inner packagings that are
required. If inner packagings are not required, a notation of ``Not
necessary'' appears in the column. The term ``Not necessary'' means
that a suitable inner packaging may be used but is not required.
(3) The third column specifies the intermediate packagings that are
required. If intermediate packagings are not required, a notation of
``Not necessary'' appears in the column. The term ``Not necessary''
means that a suitable intermediate packaging may be used but is not
required.
(4) The fourth column specifies the outer packagings which are
required. If inner packagings and/or intermediate packagings are
specified in the second and third columns, then the packaging specified
in the fourth column must be used as the outer packaging of a
combination packaging; otherwise it may be used as a single packaging.
(5) Packing Instruction 101 may be used for any explosive substance
or article if an equivalent level of safety is shown to be maintained
subject to the approval of the Associate Administrator for Hazardous
Materials Safety.
Table of Packing Methods
--------------------------------------------------------------------------------------------------------------------------------------------------------
Packing instruction Inner packagings Intermediate packagings Outer packagings
--------------------------------------------------------------------------------------------------------------------------------------------------------
101..............................
(2) This Packing Instruction may
be used as an alternative to a
specifically assigned packing
method with the approval of the
Associate Administrator for
Hazardous Materials Safety prior
to transportation. When this
packing instruction is used, the
following must be marked on the
shipping documents:
``Packaging approved by the
competent authority of the
United States of America
(USA)''.
PARTICULAR PACKING REQUIREMENTS
OR EXCEPTIONS:
1. Samples of new or existing
explosive substances or
articles may be transported as
directed by the Associate
Administrator for Hazardous
Materials Safety for purposes
including: testing,
classification, research and
development, quality control,
or as a commercial sample.
Explosive samples which are
wetted or desensitized must be
limited to 25 kg. Explosive
samples which are not wetted
or desensitized must be
limited to 10 kg in small
packages as specified by the
Associate Administrator for
Hazardous Materials Safety
110(a)........................... Bags.................................. Bags.................................. Drums.
[[Page 24723]]
PARTICULAR PACKING REQUIREMENTS plastics plastics steel, removable head (1A2).
OR EXCEPTIONS: textile, plastic coated or lined textile, plastic coated or lined plastics, removable head (1H2)
1. The Intermediate packagings rubber rubber
must be filled with water textile, rubberized textile, rubberized
saturated material such as an textile Receptacles
anti-freeze solution or wetted plastics
cushioning metal
2. Outer packagings must be
filled with water saturated
material such as an anti-
freeze solution or wetted
cushioning. Outer packagings
must be constructed and sealed
to prevent evaporation of the
wetting solution, except when
0224 is being carried dry
110(b)........................... Bags.................................. Dividing partitions................... Boxes.
PARTICULAR PACKING REQUIREMENTS rubber, conductive metal natural wood, sift-proof wall
OR EXCEPTIONS plastics, conductive wood (4C2).
For UN 0074, 0113, 0114, 0129, Receptacles........................... plastics plywood (4D).
0130, 0135 and 0224, the metal fibreboard reconstituted wood (4F).
following conditions must be wood
satisfied: rubber, conductive
a. inner packagings must not plastics, conductive
contain more than 50 g of
explosive substance (quantity
corresponding to dry
substance);
b. each inner packaging must
be separated from other inner
packagings by dividing
partitions; and
c. the outer packaging must
not be partitioned with more
than 25 compartments
111.............................. Bags.................................. Not necessary......................... Boxes.
PARTICULAR PACKING REQUIREMENTS paper, waterproofed steel (4A).
OR EXCEPTIONS: plastics aluminium (4B).
For UN 0159, inner packagings textile, rubberized natural wood, ordinary (4C1).
are not required when metal Sheets................................ natural wood, sift proof (4C2).
(1A2 or 1B2) or plastics (1H2) plastics plywood (4D).
drums are used as outer textile, rubberized reconstituted wood (4F).
packagings fibreboard (4G).
plastics, expanded (4H1).
plastics, solid (4H2).
Drums.................................
steel, removable head (1A2).
aluminum, removable head (1B2).
plywood (1D).
fibreboard (1G).
plastics, removable head (1H2).
112(a) This packing instruction Bags.................................. Bags.................................. Boxes.
applies to wetted solids.
PARTICULAR PACKING REQUIREMENTS paper, multiwall, water resistant plastics............................ steel (4A).
OR EXCEPTIONS: plastics textile, plastic coated or lined.... aluminium (4B).
1. For UN Nos. 0004, 0076, textile Receptacles........................... natural wood, ordinary (4C1).
0078, 0154, 0219 and 0394, textile, rubberized metal natural wood, sift proof (4C2).
packagings must be lead free woven plastics plastics plywood (4D).
2. Intermediate packagings are Receptacles........................... reconstituted wood (4F).
not required if leakproof metal fibreboard (4G).
drums are used as the outer plastics plastics, expanded (4H1).
packaging plastics, solid (4H2).
3. For UN 0072 and UN 0226, Drums
intermediate packagings are steel, removable head (1A2).
not required aluminium, removable head (1B2).
fibre (1G).
plastics, removable head (1H2).
112(b) This packing instruction Bags.................................. Bags (for UN 0150 only)............... Bags.
applies to dry solids other than
powders.
[[Page 24724]]
PARTICULAR PACKING REQUIREMENTS paper, Kraft plastics woven plastics sift-proof (5H2/3).
OR EXCEPTIONS: paper, multiwall, water resistant... textile, plastic coated or lined.... plastics, film (5H4).
1. For UN 0004, 0076, 0078, plastics textile, sift-proof (5L2).
0154, 0216, 0219 and 0386, textile textile, water resistant (5L3).
packagings must be lead free textile, rubberized plastics........ paper, multiwall, water resistant
2. For UN 0209, bags, sift- woven plastics (5M2).
proof (5H2) are recommended Boxes
for flake or prilled TNT in steel (4A).
the dry state and a maximum aluminium (4B).
net mass of 30 kg. natural wood, ordinary (4C1).
3. For UN 0222 and UN 0223, natural wood, sift proof (4C2).
inner packagings are not plywood (4D)
required reconstituted wood (4F).
fibreboard (4G).
plastics, expanded (4H1).
plastics, solid (4H2).
Drums
steel, removable head (1A2).
aluminium, removable head (1B2).
fibre (1G).
plastics, removable head (1H2).
112(c) This packing instruction Bags.................................. Bags.................................. Boxes.
applies to solid dry powders.
PARTICULAR PACKING REQUIREMENTS paper, multiwall, water resistant... paper, multiwall, water resistant steel (4A).
OR EXCEPTIONS: plastics with inner lining. natural wood,
1. For UN 0004, 0076, 0078, woven plastics plastics ordinary (4C1).
0154, 0216, 0219 and 0386, Receptacles........................... Receptacles........................... natural wood,
packagings must be lead free fibreboard metal sift proof (4C2).
2. For UN 0209, bags, sift- metal plastics plywood (4D).
proof (5H2) are recommended plastics reconstituted wood (4F).
for flake or prilled TNT in wood fibreboard (4G).
the dry state. Bags must not plastics, solid (4H2).
exceed a maximum net mass of Drums.
30 kg. steel, removable head (1A2)
3. Inner packagings are not aluminium, removable head (1B2) .
required if drums are used as fibre (1G).
the outer packaging.
4. At least one of the
packagings must be sift-proof
113.............................. Bags.................................. Not necessary......................... Boxes.
PARTICULAR PACKING REQUIREMENTS paper .....................................
OR EXCEPTIONS: plastics steel (4A).
1. For UN 0094 and UN 0305, no textile, rubberized natural wood, ordinary (4C1).
more than 50 g of substance Receptacles........................... natural wood, sift-proof walls
must be packed in an inner fibreboard (4C2).
packaging metal plywood (4D).
2. For UN 0027, inner plastics reconstituted wood (4F).
packagings are not necessary wood fibreboard (4G).
when drums are used as the Sheets................................ plastics, solid (4H2).
outer packaging paper, kraft Drums
3. At least one of the paper, waxed steel, removable head (1A2).
packagings must be sift- proof aluminium, removable head (1B2).
4. Sheets must only be used for fibre (1G).
UN 0028
114(a) This packing instruction Bags.................................. Bags.................................. Boxes.
applies to wetted solids.
[[Page 24725]]
PARTICULAR PACKING REQUIREMENTS .....................................
OR EXCEPTIONS: plastics............................ plastics............................ steel (4A).
1. For UN 0077, 0234, 0235 and textile textile, plastic coated or lined natural wood, ordinary (4C1).
0236, packagings must be lead woven plastics Receptacles........................... natural wood, sift proof walls
free Receptacles........................... metal (4C2).
2. For UN 0342, inner metal plastics plywood (4D).
packagings are not required plastics reconstituted wood (4F).
when metal (1A2 or 1B2) or fibreboard (4G).
plastics (1H2) drums are used plastics, solid (4H2).
as outer packagings Drums.
3. Intermediate packagings are steel, removable head (1A2).
not required if leakproof aluminium, removable head (1B2).
removable head drums are used plywood (1D).
as the outer packaging fibre (1G).
plastics,
removable head (1H2).
114(b) This packing instruction Bags.................................. Not necessary......................... Boxes.
applies to dry solids
PARTICULAR PACKING REQUIREMENTS ...................................... natural wood, ordinary (4C1).
OR EXCEPTIONS: paper, kraft........................ natural wood, sift proof walls (4C2)
1. For UN 0077, 0132, 0234, plastics plywood (4D).
0235 and 0236, packagings must textile, sift-proof reconstituted wood (4F).............
be lead free woven plastics, sift-proof.......... fibreboard (4G).
2. For UN 0160 and UN 0161, Receptacles........................... Drums.
when metal drums (1A2 or 1B2) fibreboard steel, removable head (1A2).........
are used as the outer metal aluminium, removable head (1B2).....
packaging, metal packagings paper plywood (1D).
must be so constructed that plastics fibre (1G).
the risk of explosion, by woven plastics, sift-proof.......... plastics, removable head (1H2)......
reason of increased internal
pressure from internal or
external causes is prevented
3. For UN 0160 and UN 0161,
inner packagings are not
required if drums are used as
the outer packaging
115.............................. Receptacles........................... Bags.................................. Boxes.
PARTICULAR PACKING REQUIREMENTS metal plastics in metal receptacles natural wood, ordinary (4C1).
OR EXCEPTIONS: plastics Drums................................. natural wood, sift proof walls
1. For liquid explosives, inner metal (4C2).
packagings must be surrounded plywood (4D).
with non-combustible absorbent reconstituted wood (4F).
cushioning material in fibreboard (4G).
sufficient quantity to absorb Drums.
the entire liquid content. steel, removable head (1A2).
Metal receptacles should be aluminium, removable head (1B2).
cushioned from each other. The plywood (1D).
net mass of explosive per fibre (1G).
package may not exceed 30 kg Specification MC-200 containers may
when boxes are used as outer be used for transport by motor
packaging. The net volume of vehicle.
explosive in each package
other than boxes must not
exceed 120 litres
2. For UN 0075, 0143, 0495 and
0497 when boxes are used as
the outer packaging, inner
packagings must have taped
screw cap closures and be not
more than 5 litres capacity
each. A composite packaging
consisting of a plastic
receptacle in a metal drum
(6HA1) may be used in lieu of
combination packagings. Liquid
substances must not freeze at
temperatures above -15 deg.C
(+5 deg.F)
3. For UN 0144, intermediate
packagings are not necessary.
Receptacles
116.............................. Bags.................................. Not necessary......................... Bags.
[[Page 24726]]
PARTICULAR PACKING REQUIREMENTS paper, water and oil woven plastics (5H1/2/3).
OR EXCEPTIONS: resistant paper, mulitwall, water resistant
1. For UN 0082, 0241, 0331 and plastics (5M2).
0332, inner packagings are not texitile, plasic coated or plastics, film (5H4).
necessary if leakproof lined textile, sift-proof (5L2).
removable head drums are used woven plasics, sift-proof textile, water resistant (5L3).
as the outer packaging Receptacles........................... Boxes.
2. For UN 0082, 0241, 0331 and fibreboard, water resistant......... steel (4A).
0332, inner packagings are not metal aluminium (4B).
required when the explosive is plastics wood, natural, ordinary (4C1).
contained in a material wood, sift-proof natural wood, sift proof walls
impervious to liquid Sheets................................ (4C2).
3. For UN 0081, inner paper, water resistant plywood (4D).
packagings are not required paper, waxed reconstituted wood (4F).
when contained in rigid plastics fibreboard (4G).
plastic which is impervious to plastics, solid (4H2).
nitric esters Drums.
4. For UN 0331, inner steel, removable head (1A2).
packagings are not required aluminium, removable head (1B2).
when bags (5H2), (5H3) or fibre (1G).
(5H4) are used as outer plastics, removable head (1H2).
packagings Jerricans.
5. Bags (5H2 or 5H3) must be steel, removable head (3A2).
used only for UN 0082, 0241, plastics, removable head (3H2).
0331 and 0332
6. For UN 0081, bags must not
be used as outer packagings
117.............................. Not necessary......................... Not necessary......................... IBCs.
PARTICULAR PACKING REQUIREMENTS metal (11A), (11B), (11N), (21A),
OR EXCEPTIONS: (21B), (21N), (31A), (31B), (31N).
1. This packing instruction may flexible (13H2), (13H3), (13H4),
only be used for explosives of (13L2), (13L3), (13L4), (13M2).
0082 when they are mixtures of rigid plastics (11H1), (11H2),
ammonium nitrate or other (21H1), (21H2), (31H1), (31H2).
inorganic nitrates with other composite (11HZ1), (11HZ2),
combustible substances which (21HZ1), (21HZ2), (31HZ1),
are not explosive ingredients. (31HZ2).
Such explosives must not
contain nitroglycerin, similar
liquid organic nitrates,
liquid or solid nitrocarbons,
or chlorates.
2. This packing instruction may
only be used for explosives of
UN 0241 which consist of water
as an essential ingredient and
high proportions of ammonium
nitrate or other oxidizers,
some or all of which are in
solution. The other
constituents may include
hydrocarbons or aluminium
powder, but must not include
nitro-derivatives such as
trinitrotoluene.
3. Metal IBCs must not be used
for UN 0082 and 0241.
4. Flexible IBCs may only be
used for solids.
130.............................. Not necessary......................... No necessary.......................... Boxes.
[[Page 24727]]
PARTICULAR PACKING REQUIREMENTS steel (4A).
OR EXCEPTIONS: aluminium (4B).
1. The following applies to UN wood natural, ordinary (4C1).
0006, 0009, 0010, 0015, 0016, natural wood, sift proof walls
0018, 0019, 0034, 0035, 0038, (4C2).
0039, 0048, 0056, 0137, 0138, plywood (4D).
0168, 0169, 0171, 0181, 0182, reconstituted wood (4F).
0183, 0186, 0221, 0238, 0243, fibreboard (4G).
0244, 0245, 0246, 0254, 0280, plastics, expanded (4H1).
0281, 0286, 0287, 0297, 0299, plastics, solid (4H2).
0300, 0301, 0303, 0321, 0328, Drums.
0329, 0344, 0345 0346, 0347, steel, removable head (1A2).
0362, 0363, 0370, 0412, 0424, aluminium, removable head (1B2).
0425, 0434, 0435, 0436, 0437, fibre (1G).
0438, 0451, 0459 and 0488. plastics, removable head (1H2).
Large and robust explosives
articles, normally intended
for military use, without
their means of initiation or
with their means of initiation
containing at least two
effective protective features,
may be carried unpackaged.
When such articles have
propelling charges or are self-
propelled, their ignition
systems must be protected
against stimuli encountered
during normal conditions of
transport. A negative result
in Test Series 4 on an
unpackaged article indicates
that the article can be
considered for transport
unpackaged. Such unpackaged
articles may be fixed to
cradles or contained in crates
or other suitable handling
devices.
131.............................. Bags.................................. Not necessary......................... Boxes.
PARTICULAR PACKING REQUIREMENTS paper steel (4A).
OR EXCEPTIONS: plastics aluminium (4B).
1. For UN 0029, 0267 and 0455, Receptacles wood, natural, ordinary (4C1).
bags and reels may not be used fibreboard natural wood, sift proof walls
as inner packagings metal (4C2).
2. For UN 0030, 0255 and 0456, plastics plywood (4D).
inner packagings are not wood reconstituted wood (4F).
required when detonators are Reels fibreboard (4G).
packed in pasteboard tubes, or Drums.
when their leg wires are wound steel, removable head (1A2).
on spools with the caps either aluminium, removable head (1B2).
placed inside the spool or fibre (1G).
securely taped to the wire on plastics, removable head (1H2).
the spool, so as to restrict
freedom of movement of the
caps and to protect them from
impact forces
3. For UN 0360, 0361 and 0500,
detonators are not required to
be attached to the safety
fuse, metal-clad mild
detonating cord, detonating
cord, or shock tube. Inner
packagings are not required if
the packing configuration
restricts freedom of movement
of the caps and protects them
from impact forces
132(a)........................... Not necessary......................... Not necessary......................... Boxes.
steel (4A).
aluminium (4B).
wood, natural, ordinary (4C1).
wood, natural, sift proof walls
(4C2).
plywood (4D).
reconstituted wood (4F).
fibreboard (4G).
plastics, solid (4H2).
132(b)........................... Receptacles........................... Not necessary......................... Boxes.
fibreboard steel (4A).
metal aluminium (4B).
plastics wood, natural, ordinary (4C1).
Sheets wood, natural, sift proof walls
paper (4C2).
plastics plywood (4D).
reconstituted wood (4F).
fibreboard (4G).
plastics, solid (4H2).
133.............................. Receptables........................... Receptables........................... Boxes.
[[Page 24728]]
PARTICULAR PACKING REQUIREMENTS fibreboard.......................... fibreboard steel (4A).
OR EXCEPTIONS: metal............................... metal aluminium (4B).
1. For UN 0043, 0212, 0225, plastics............................ plastics wood, natural, ordinary (4C1).
0268 and 0306 trays are not wood................................ wood wood, natural, sift proof walls
authorized as inner packagings Trays, fitted with dividing........... (4C2).
2. Intermediate packagings are partitions............................ plywood (4D).
only required when trays are fibreboard reconstituted wood (4F).
used as inner packagings plastics fibreboard (4G).
wood plastics, solid (4H2).
134.............................. Bags.................................. Not necessary......................... Boxes.
water resistant steel (4A).
Receptacles aluminium (4B).
fibreboard wood, natural, ordinary (4C1).
metal wood, natural, sift proof walls
plastics (4C2).
wood plywood (4D).
Sheets reconstituted wood (4F).
fibreboard, corrugated fibreboard (4G).
Tubes plastics, solid (4H2).
fibreboard Drums.
steel, removable head (1A2).
aluminium, removable head (1B2).
135.............................. Bags.................................. Not necessary......................... Boxes.
paper steel (4A).
plastics aluminium (4B).
Receptacles wood, natural, ordinary (4C1).
fibreboard wood, natural, sift proof walls
metal (4C2).
plastics plywood (4D).
wood reconstituted wood (4F).
Sheets fibreboard (4G).
paper plastics, expanded (4H1).
plastics plastics, solid (4H2).
Drums.
steel, removable head (1A2).
aluminium, removable head (1B2).
fibre (1G).
plastics, removable head (1H2).
136.............................. Bags.................................. Not necessary......................... Boxes.
plastics steel (4A).
textile aluminium (4B)
Boxes. wood, natural, ordinary (4C1).
fibreboard wood, natural, sift proof walls
plastics (4C2).
wood plywood (4D).
Dividing partitions in the reconstituted wood (4F).
outer packagings...................... fibreboard (4G).
plastics, solid (4H2).
Drums.
steel, removable head (1A2).
aluminium, removable head (1B2).
fibre (1G).
plastics, removable head (1H2).
137.............................. Bags.................................. Not necessary......................... Boxes.
[[Page 24729]]
PARTICULAR PACKING REQUIREMENTS plastics steel (4A).
OR EXCEPTIONS: Boxes................................. aluminium (4B).
For UN 0059, 0439, 0440 and fibreboard wood, natural, ordinary (4C1).
0441, when the shaped charges Tubes................................. wood, natural, sift proof walls
are packed singly, the conical fibreboard (4C2).
cavity must face downwards and metal plywood (4D).
the package marked ``THIS SIDE plastics reconstituted wood (4F).
UP''. When the shaped charges Dividing partitions in the outer fibreboard (4G).
are packed in pairs, the packagings.
conical cavities must face
inwards to minimize the
jetting effect in the event of
accidental initiation
138.............................. Bags.................................. Not necessary......................... Boxes.
PARTICULAR PACKING REQUIREMENTS plastics steel (4A).
OR EXCEPTIONS: aluminium (4B).
If the ends of the articles are wood, natural, ordinary (4C1).
sealed, inner packagings are wood, natural, sift proof walls
not necessary (4C2).
plywood (4D).
reconstituted wood (4F).
fibreboard (4G).
plastics, solid (4H2).
Drums.
steel, removable head (1A2).
aluminium, removable head (1B2).
139.............................. Bags.................................. Not necessary......................... Boxes.
PARTICULAR PACKING REQUIREMENTS plastics steel (4A).
OR EXCEPTIONS: Receptacles........................... aluminium (4B).
1. For UN 0065, 0102, 0104, fibreboard wood, natural, ordinary (4C1).
0289 and 0290, the ends of the metal wood, natural, sift proof walls
detonating cord must be plastics (4C2).
sealed, for example, by a plug wood plywood (4D).
firmly fixed so that the Reels................................. reconstituted wood (4F).
explosive cannot escape. The Sheets................................ fibreboard (4G).
ends of CORD DETONATING paper plastics, solid (4H2).
flexible must be fastened plastics Drums.
securely steel, removable head (1A2).
2. For UN 0065 and UN 0289, aluminium, removable head (1B2).
inner packagings are not plywood (1D).
required when they are fibre (1G).
fastened securely in coils plastics, removable head (1H2).
140.............................. Bags.................................. Not necessary......................... Boxes.
PARTICULAR PACKING REQUIREMENTS plastics steel (4A).
OR EXCEPTIONS: Reels................................. aluminium (4B).
1. If the ends of UN 0105 are Sheets................................ wood, natural, ordinary (4C1).
sealed, no inner packagings paper, kraft wood, natural, sift proof walls
are required plastics (4C2).
2. For UN 0101, the packaging plywood (4D).
must be sift-proof except when reconstituted wood (4F).
the fuse is covered by a paper fibreboard (4G).
tube and both ends of the tube plastics, solid (4H2).
are covered with removable Drums.
caps steel, removable head (1A2).
3. For UN 0101, steel or aluminium, removable head (1B2).
aluminium boxes or drums must fibre (1G).
not be used
[[Page 24730]]
141.............................. Receptacles........................... Not necessary......................... Boxes.
fibreboard steel (4A).
metal aluminium (4B).
plastics wood, natural, ordinary (4C1).
wood wood, natural, sift proof walls
Trays, fitted with dividing partitions (4C2).
plastics plywood (4D).
wood reconstituted wood (4F).
Dividing partitions in the outer fibreboard (4G).
packagings. plastics, solid (4H2).
Drums.
steel, removable head (1A2).
aluminium, removable head (1B2).
fibre (1G).
plastics, removable head (1H2).
142.............................. Bags.................................. Not necessary......................... Boxes.
paper steel (4A).
plastics aluminium (4B).
Receptacles........................... wood, natural, ordinary (4C1).
fibreboard wood, natural, sift proof walls
metal (4C2).
plastics plywood (4D).
wood reconstituted wood (4F).
Sheets................................ fibreboard (4G).
paper plastics, solid (4H2).
Trays, fitted with dividing partitions Drums.
plastics steel, removable head (1A2).
aluminium, removable head (1B2).
fibre (1G).
plastics, removable head (1H2).
143.............................. Bag................................... Not necessary......................... Boxes.
PARTICULAR PACKING REQUIREMENTS paper, kraft........................ steel (4A).
OR EXCEPTIONS: plastics aluminum (4B).
1. For UN 0271, 0272, 0415 and textile wood, natural, ordinary (4C1).
0491 when metal packagings are textile, rubberized wood, natural, sift proof walls
used, metal packagings must be Receptacles........................... (4C2).
so constructed that the risk fibreboard plywood (4D).
of explosion, by reason of metal reconstituted wood (4F).
increase in internal pressure plastics fibreboard (4G).
from internal or external Trays, fitted with dividing partitions plastics, solid (4H2).
causes is prevented plastics Drums.
2. Composite packagings (6HH2) wood steel, removable head (1A2).
(plastic receptacle with outer aluminium, removable head (1B2).
solid box) may be used in lieu plywood (1D).
of combination packagings fibre (1G).
plastics, removable head (1H2).
144.............................. Receptacles........................... Not necessary......................... Boxes.
PARTICULAR PACKING REQUIREMENTS fibreboard steel (4A).
OR EXCEPTIONS: metal aluminum (4B).
For UN 0248 and UN 0249, plastics wood, natural, ordinary (4C1) with
packagings must be protected Dividing partitions in the outer metal liner.
against the ingress of water. packagings. plywood (4D) with metal liner.
When CONTRIVANCES, WATER reconstituted wood (4F) with metal
ACTIVATED are transported liner.
unpackaged, they must be plastics, expanded (4H1).
provided with at least two
independent protective
features which prevent the
ingress of water
US 1
1. A jet perforating gun, charged, oil well may be transported under the following conditions:
[[Page 24731]]
a. Initiation devices carried on the same motor vehicle or offshore supply vessel must be segregated; each kind from every other kind, and from any
gun, tool or other supplies, unless approved in accordance with Sec. 173.56. Segregated initiation devices must be carried in a container having
individual pockets for each such device or in a fully enclosed steel container lined with a non-sparking material. No more than two segregated
initiation devices per gun may be carried on the same motor vehicle..
b. Each shaped charge affixed to the gun may not contain more than 112 g (4 ounces) of explosives.....................................................
c. Each shaped charge if not completely enclosed in glass or metal, must be fully protected by a metal cover after installation in the gun............
d. A jet perforating gun classed as 1.1D or 1.4D may be transported by highway by private or contract carriers engaged in oil well operations.........
(i) A motor vehicle transporting a gun must have specially built racks or carrying cases designed and constructed so that the gun is securely held in
place during transportation and is not subject to damage by contact, one to the other or any other article or material carried in the vehicle; and.
(ii) The assembled gun packed on the vehicle may not extend beyond the body of the motor vehicle......................................................
e. A jet perforating gun classed as 1.4D may be transported by a private offshore supply vessel only when the gun is carried in a motor vehicle as
specified in paragraph (d) of this packing method or on offshore well tool pallets provided that:.
(i) All the conditions specified in paragraphs (a), (b), and (c) of this packing method are met;......................................................
(ii) The total explosive contents do not exceed 90.8 kg (200 pounds) per tool pallet;.................................................................
(iii) Each cargo vessel compartment may contain up to 90.8 kg (200 pounds) of explosive content if the segregation requirements in Sec. 176.83(b)(3)
of this subchapter are met; and.
(iv) When more than one vehicle or tool pallet is stowed ``on deck'' a minimum horizontal separation of 3 m (9.8 feet) must be provided...............
--------------------------------------------------------------------------------------------------------------------------------------------------------
(d) Class 1 (explosive) materials owned by the Department of
Defense and packaged prior to January 1, 1990, in accordance with the
requirements of this subchapter in effect at that time, are excepted
from the requirements of part 178 of this subchapter provided the
packagings have maintained their integrity and the explosive material
is declared as government-owned goods packaged prior to January 1,
1990.
30. In Sec. 173.120, paragraph (a)(3) is revised, the last sentence
in paragraph (b)(3) is revised, the word ``or'' is removed at the end
of paragraph (c)(1)(i)(A), the period at the end of paragraph
(c)(1)(i)(B) is removed and ``; or'' is added in its place, and a new
paragraph (c)(1)(i)(C) is added, to read as follows:
Sec. 173.120 Class 3--Definitions.
(a) * * *
(3) Any liquid with a flash point greater than 35 deg.C (95 deg.F)
which does not sustain combustion according to ASTM 4206 or the
procedure in Appendix H of this part.
* * * * *
(b) * * *
(3) * * * Either the test method specified in ASTM 4206 or the
procedure in Appendix H of this part may be used to determine if a
material sustains combustion when heated under test conditions and
exposed to an external source of flame.
(c) * * *
(1) * * *
(i) * * *
(C) Standard Test Methods for Flash Point by Small Scale Closed
Tester, (ASTM D 3828).
* * * * *
Sec. 173.124 [Amended]
31. In Sec. 173.124, the following changes are made:
a. In paragraph (a)(1) introductory text, the word ``Wetted'' is
revised to read ``Desensitized''.
b. In paragraph (a)(2)(i)(D)(2) the words ``for a 50 kg package''
is added after the words ``greater than 75 deg.C (167 deg.F)''.
c. In paragraphs (a)(3)(ii) and (iii), the wording ``paragraph
2.c.(2) of appendix E to this part'' is revised to read ``UN Manual of
Tests and Criteria'' each place it appears.
d. In paragraph (b)(1), the wording ``paragraph 3.a.(1) or 3.a.(2),
as appropriate, of appendix E to this part'' is revised to read ``the
UN Manual of Tests and Criteria''.
e. In paragraph (b)(2), the wording ``paragraph 3.b.(1) of appendix
E to this part'' is revised to read ``UN Manual of Tests and
Criteria''.
f. In paragraph (c), the wording ``paragraph 4 of appendix E to
this part'' is revised to read ``UN Manual of Tests and Criteria''.
32. In Sec. 173.125, paragraphs (b), (c)(2)(i), (c)(2)(ii), and
(d)(1) through (d)(3) are revised to read as follows:
Sec. 173.125 Class 4--Assignment of packing group.
* * * * *
(b) Packing group criteria for readily combustible materials of
Division 4.1 are as follows:
(1) Powdered, granular or pasty materials must be classified in
Division 4.1 when the time of burning of one or more of the test runs,
in accordance with the UN Manual of Tests and Criteria, is less than 45
seconds or the rate of burning is more than 2.2 mm/s. Powders of metals
or metal alloys must be classified in Division 4.1 when they can be
ignited and the reaction spreads over the whole length of the sample in
10 minutes or less.
(2) Packing group criteria for readily combustible materials of
Division 4.1 are assigned as follows:
(i) For readily combustible solids (other than metal powders),
Packing Group II if the burning time is less than 45 seconds and the
flame passes the wetted zone. Packing Group II must be assigned to
powders of metal or metal alloys if the zone of reaction spreads over
the whole length of the sample in 5 minutes or less.
(ii) For readily combustible solids (other than metal powders),
Packing Group III must be assigned if the burning rate time is less
than 45 seconds and the wetted zone stops the flame propagation for at
least 4 minutes. Packing Group III must be assigned to metal powders if
the reaction spreads over the whole length of the sample in more than 5
minutes but not more than 10 minutes.
(c) * * *
(2) * * *
(i) Packing Group II, if the material gives a positive test result
when tested with a 25 mm cube size sample at 140 deg.C; or
(ii) Packing Group III, if--
(A) A positive test result is obtained in a test using a 100 mm
sample cube at 140 deg.C and a negative test result is obtained in a
test using a 25 mm sample cube at 140 deg.C and the substance is
transported in packagings with a volume of more than 3 cubic meters; or
(B) A positive test result is obtained in a test using a 100 mm
sample cube at 120 deg.C and a negative result is obtained in a test
using a 25 mm sample cube at 140 deg.C and the substance is
[[Page 24732]]
transported in packagings with a volume of more than 450 liters; or
(C) A positive result is obtained in a test using a 100 mm sample
cube at 100 deg.C and a negative result is obtained in a test using a
25 mm sample cube at 140 deg.C and the substance is transported in
packagings with a volume of less than 450 liters.
(d) * * *
(1) Packing Group I, if the material reacts vigorously with water
at ambient temperatures and demonstrates a tendency for the gas
produced to ignite spontaneously, or which reacts readily with water at
ambient temperatures such that the rate of evolution of flammable gases
is equal or greater than 10 liters per kilogram of material over any
one minute;
(2) Packing Group II, if the material reacts readily with water at
ambient temperatures such that the maximum rate of evolution of
flammable gases is equal to or greater than 20 liters per kilogram of
material per hour, and which does not meet the criteria for Packing
Group I; or
(3) Packing Group III, if the material reacts slowly with water at
ambient temperatures such that the maximum rate of evolution of
flammable gases is greater than 1 liter per kilogram of material per
hour, and which does not meet the criteria for Packing Group I or II.
33. Section 173.127 is revised to read as follows:
Sec. 173.127 Class 5, Division 5.1--Definition and assignment of
packing groups.
(a) Definition. For the purpose of this subchapter, oxidizer
(Division 5.1) means a material that may, generally by yielding oxygen,
cause or enhance the combustion of other materials.
(1) A solid material is classed as a Division 5.1 material if, when
tested in accordance with the UN Manual of Tests and Criteria, its mean
burning time is less than or equal to the burning time of a 3:7
potassium bromate/cellulose mixture.
(2) A liquid material is classed as a Division 5.1 material if,
when tested in accordance with the UN Manual of Tests and Criteria, it
spontaneously ignites or its mean time for a pressure rise from 690 kPa
to 2070 kPa gauge is less then the time of a 1:1 nitric acid (65
percent)/cellulose mixture.
(b) Assignment of packing groups. (1) The packing group of a
Division 5.1 material which is a solid shall be assigned using the
following criteria:
(i) Packing Group I, for any material which, in either
concentration tested, exhibits a mean burning time less than the mean
burning time of a 3:2 potassium bromate/cellulose mixture.
(ii) Packing Group II, for any material which, in either
concentration tested, exhibits a mean burning time less than or equal
to the mean burning time of a 2:3 potassium bromate/cellulose mixture
and the criteria for Packing Group I are not met.
(iii) Packing Group III for any material which, in either
concentration tested, exhibits a mean burning time less than or equal
to the mean burning time of a 3:7 potassium bromate/cellulose mixture
and the criteria for Packing Group I and II are not met.
(2) The packing group of a Division 5.1 material which is a liquid
shall be assigned using the following criteria:
(i) Packing Group I for:
(A) Any material which spontaneously ignites when mixed with
cellulose in a 1:1 ratio; or
(B) Any material which exhibits a mean pressure rise time less than
the pressure rise time of a 1:1 perchloric acid (50 percent)/cellulose
mixture.
(ii) Packing Group II, any material which exhibits a mean pressure
rise time less than or equal to the pressure rise time of a 1:1 aqueous
sodium chlorate solution (40 percent)/cellulose mixture and the
criteria for Packing Group I are not met.
(iii) Packing Group III, any material which exhibits a mean
pressure rise time less than or equal to the pressure rise time of a
1:1 nitric acid (65 percent)/cellulose mixture and the criteria for
Packing Group I and II are not met.
Sec. 173.128 [Amended]
34. In Sec. 173.128, the following changes are made:
a. In paragraph (c)(3), the wording ``United Nations
Recommendations on the Transport of Dangerous Goods, Tests and
Criteria, part III'' would be revised to read ``UN Manual of Tests and
Criteria'.
b. In paragraph (e), the wording ``Figure 11.1 (Classification and
Flow Chart Scheme for Organic Peroxides) from the UN Recommendations,
Tests and Criteria, part III'' would be revised to read ``Figure
20.1(a) (Classification and Flow Chart Scheme for Organic Peroxides)
from the UN Manual of Tests and Criteria''.
35. In Sec. 173.132, a new paragraph (b)(3)(iii) is added,
paragraph (c) is redesignated as paragraph (d), and a new paragraph (c)
is added, to read as follows:
Sec. 173.132 Class 6, Division 6.1--Definitions.
* * * * *
(b) * * *
(3) * * *
(iii) A solid substance should be tested if at least 10 percent of
its total mass is likely to be dust in a respirable range, e.g. the
aerodynamic diameter of that particle-fraction is 10 microns or less. A
liquid substance should be tested if a mist is likely to be generated
in a leakage of the transport containment. In carrying out the test
both for solid and liquid substances, more than 90% (by mass) of a
specimen prepared for inhalation toxicity testing must be in the
respirable range as defined in this paragraph (b)(3)(iii).
(c) For purposes of classifying and assigning packing groups to
mixtures possessing oral or dermal toxicity hazards according to the
criteria in Sec. 173.133(a)(1), it is necessary to determine the acute
LD50 of the mixture. If a mixture contains more than one
active constituent, one of the following methods may be used to
determine the oral or dermal LD50 of the mixture:
(1) Obtain reliable acute oral and dermal toxicity data on the
actual mixture to be transported;
(2) If reliable, accurate data is not available, classify the
formulation according to the most hazardous constituent of the mixture
as if that constituent were present in the same concentration as the
total concentration of all active constituents; or
(3) If reliable, accurate data is not available, apply the formula:
[GRAPHIC] [TIFF OMITTED] TR06MY97.000
where:
C = the % concentration of constituent A, B ... Z in the mixture;
T = the oral LD50 values of constituent A, B ... Z;
TM = the oral LD50 value of the mixture.
Note to formula in paragraph (c)(3): This formula also may be
used for dermal toxicities provided that this information is
available on the same species for all constituents. The use of this
formula does not take into account any potentiation or protective
phenomena.
* * * * *
36. In Sec. 173.136, a new paragraph (c) is added to read as
follows:
Sec. 173.136 Class 8--Definitions
* * * * *
(c) Skin corrosion test data produced no later than September 30,
1995, using the procedures of Part 173, Appendix A, in effect on
September 30, 1995 (see 49 CFR Part 173, Appendix A, revised as of
October 1, 1994) for appropriate exposure times may be used for
classification and assignment of packing
[[Page 24733]]
group for Class 8 materials corrosive to skin.
Sec. 173.137 [Amended]
37. In Sec. 173.137, the following changes are made:
a. In paragraph (b), the wording ``other than those meeting Packing
Group I criteria'' is added immediately following the word
``Materials''.
b. In paragraph (c)(2), at the end of the paragraph, the wording
``(Reapproved 1990)'' is revised to read ``(Reapproved 1995)''.
38. In Sec. 173.152, a new paragraph (b)(4) is added to read as
follows:
Sec. 173.152 Exceptions for Division 5.1 (oxidizers) and Division 5.2
(organic peroxides).
* * * * *
(b) * * *
(4) For polyester resin kits consisting of a base material
component (Class 3, Packing Group II or III) and an activator component
(Type C, D, E, or F organic peroxide which does not require temperature
control)--
(i) the organic peroxide component must be packed in inner
packagings not over 125 ml (4.22 ounces) net capacity each for liquids
or 500 g (17.64 ounces) net capacity each for solids;
(ii) The flammable liquid component must be packed in inner
packagings not over 1.0 L (0.3 gallons) net capacity each for Packing
Group II liquids or 5.0 L (1.3 gallons) net capacity each for Packing
Group III liquids; and
(iii) The flammable liquid component and the organic peroxide
component may be packed in the same strong outer packaging provided
they will not interact dangerously in the event of leakage.
* * * * *
39. In Sec. 173.162, a sentence is added at the end of the section
to read as follows:
Sec. 173.162 Gallium.
* * * Manufactured articles or apparatuses, each containing not
more than 100 mg (0.0035 ounce) of gallium and packaged so that the
quantity of gallium per package does not exceed 1 g (0.35 ounce) are
not subject to the requirements of this subchapter.
40. In Sec. 173.166, the section heading and paragraph (e) are
revised to read as follows:
Sec. 173.166 Air bag inflators, air bag modules and seat-belt
pretensioners.
* * * * *
(e) Packagings. The following packagings are authorized:
(1) 1A2, 1B2, 1G or 1H2 drums.
(2) 3A2 or 3H2 jerricans.
(3) 4C1, 4C2, 4D, 4F, 4G or 4H2 boxes.
(4) Reusable high strength plastic or metal containers or dedicated
handling devices are authorized for shipment of air bag inflators, air
bag modules, and seat-belt pretensioners from a manufacturing facility
to the assembly facility, subject to the following conditions:
(i) The gross weight of the container or handling device may not
exceed 1000 kg (2205 pounds). The container or handling device
structure must provide adequate support to allow them to be stacked at
least three high with no damage to the containers or devices.
(ii) If not completely enclosed by design, the container or
handling device must be covered with plastic, fiberboard, or metal. The
covering must be secured to the container by banding or other
comparable methods.
(iii) Internal dunnage must be sufficient to prevent movement of
the devices within the container.
* * * * *
Sec. 173.166 [Amended]
41. In addition, in Sec. 173.166, the following changes are made:
a. The last sentence in paragraph (a) is removed.
b. In paragraph (b) introductory text, the wording ``air bag
inflator, air bag module, seat-belt pre-tensioner or seat-belt module''
is revised to read ``air bag inflator, air bag module, or seat-belt
pre-tensioner''.
c. In paragraph (b)(2), the wording ``Tests and Criteria, Second
Edition, 1990'' is revised to read ``Manual of Tests and Criteria,
second revised edition, 1995''.
d. In paragraph (b)(4), the wording ``or seat-belt'' and the
wording ``or seat-belt pre-tensioner'' are removed.
e. In paragraph (c), in the last sentence, the wording ``or pre-
tensioner'' is removed.
f. In paragraph (d)(1), the wording ``An air bag or seat-belt
module'' is revised to read ``An air bag module or seat-belt
pretensioner''.
g. In paragraph (d)(2), the wording ``or seat-belt'' and the
wording ``or pre-tensioner'' are removed.
h. In paragraph (f), in the first sentence, the wording ``or
handling device'' is added immediately following ``each package''.
42. Section 173.185 is revised to read as follows:
Sec. 173.185 Lithium batteries and cells.
(a) Except as otherwise provided in this subpart, a lithium cell or
battery is authorized for transportation only if it conforms to the
provisions of this section.
(b) Exceptions. Cells and batteries are not subject to the
requirements of this subchapter if they meet the following
requirements:
(1) Each cell with a liquid cathode may contain no more than 0.5 g
of lithium or lithium alloy, and each cell with a solid cathode may
contain no more than 1.0 g lithium or lithium alloy;
(2) Each battery with a liquid cathode may contain an aggregate
quantity of no more than 1.0 g lithium or lithium alloy, and each
battery with a solid cathode may contain an aggregate quantity of no
more than 2.0 g of lithium or lithium alloy;
(3) Each cell or battery containing a liquid cathode must be
hermetically sealed;
(4) Cells and batteries must be packed in such a way so as to
prevent short circuits and must be packed in strong packagings, except
when installed in equipment; and
(5) If a liquid cathode battery contains more than 0.5 g of lithium
or lithium alloy or a solid cathode battery contains more than 1.0 g
lithium or lithium alloy, it may not contain a liquid or gas that is a
hazardous material according to this subchapter unless the liquid or
gas, if free, would be completely absorbed or neutralized by other
materials in the battery.
(c) Cells and batteries also are not subject to this subchapter if
they meet the following requirements:
(1) Each cell contains not more than 5 g of lithium or lithium
alloy;
(2) Each battery contains not more than 25 g of lithium or lithium
alloy;
(3) Each cell or battery is of the type proven to be non-dangerous
by testing in accordance with tests in the UN Manual of Tests and
Criteria, such testing must be carried out on each type prior to the
initial transport of that type; and
(4) Cells and batteries are designed or packed in such a way as to
prevent short circuits under conditions normally encountered in
transportation.
(d) Cells and batteries and equipment containing cells and
batteries which were first transported prior to January 1, 1995, and
were assigned to Class 9 on the basis of the requirements of this
subchapter in effect on October 1, 1993, may continue to be transported
in accordance with the applicable requirements in effect on October 1,
1993.
(e) Cells and batteries may be transported as items of Class 9 if
they meet the requirements in paragraphs (e)(1) through (e)(9) of this
section:
(1) Cells must not contain more than 12 g of lithium or lithium
alloy.
(2) Batteries must not contain more than 500 g of lithium or
lithium alloy.
[[Page 24734]]
(3) Each cell and battery must be equipped with an effective means
of preventing external short circuits.
(4) Each cell and battery must incorporate a safety venting device
or be designed in a manner that will preclude a violent rupture under
conditions normally incident to transportation.
(5) Batteries containing cells or series of cells connected in
parallel must be equipped with diodes to prevent reverse current flow.
(6) Cells and batteries must be packed in strong inner packagings
containing not more than 500 g of lithium or lithium alloy per inner
packaging.
(7) Cells and batteries must be packed in inner packagings in such
a manner as to effectively prevent short circuits and to prevent
movement which could lead to short circuits.
(8) Cells and batteries must be packaged in packagings conforming
to the requirements of part 178 of this subchapter at the Packing Group
II performance level: Inner packagings must be packed within metal
boxes (4A or 4B), wooden boxes (4C1, 4C2, 4D,or 4F), fiberboard boxes
(4G), solid plastic boxes (4H2), fiber drums (1G), metal drums (1A2 or
1B2), plywood drums (1D), plastic jerricans (3H2), or metal jerricans
(3A2 or 3B2).
(9) Each cell or battery must be of the type proven to meet the
criteria of Class 9 by testing in accordance with tests in the UN
Manual of Tests and Criteria.
(10) Except as provided in paragraph (h) of this section, cells or
batteries may not be offered for transportation or transported if any
cell has been discharged to the extent that the open circuit voltage is
less than two volts or is less than \2/3\ of the voltage of the fully
charged cell, whichever is less.
(f) Equipment containing or packed with cells and batteries meeting
the requirements of paragraph (b) or (c) of this section is excepted
from all other requirements of this subchapter.
(g) Equipment containing or packed with cells and batteries may be
transported as items of Class 9 if the batteries and cells meet all the
requirements of paragraph (e) of this section and are packaged as
follows:
(1) Equipment containing cells and batteries must be packed in a
strong outer packaging that is waterproof or is made waterproof through
the use of a liner unless the equipment is made waterproof by nature of
its construction. The equipment must be secured within the outer
packaging and be packed as to effectively prevent movement, short
circuits, and accidental operation during transport; and
(2) Cells and batteries packed with equipment must be packed in
inner packagings conforming to paragraph (e)(8) of this section in such
a manner as to effectively prevent movement and short circuits. The
quantity of lithium contained in any piece of equipment must not exceed
12 g per cell and 500 g per battery. Not more than 5 kg of cells and
batteries may be packed with each item of equipment.
(h) Cells and batteries, for disposal, may be offered for
transportation or transported to a permitted storage facility and
disposal site by motor vehicle when they meet the following
requirements:
(1) Cells, when new, may not contain more than 12 g and batteries
may not contain more than 500 g of lithium or lithium alloy;
(2) Be equipped with an effective means of preventing external
short circuits; and
(3) Be packed in a strong outer packaging conforming to the
requirements of Secs. 173.24 and 173.24a. The packaging need not
conform to performance requirements of part 178 of this subchapter.
(i) Cells and batteries and equipment containing or packed with
cells and batteries which do not comply with the provisions of this
section may be transported only if they are approved by the Associate
Administrator for Hazardous Materials Safety.
(j) For testing purposes, when not contained in equipment, cells
containing not more than 12 g of lithium or lithium alloy and batteries
containing not more than 500 g of lithium or lithium alloy may be
offered for transportation or transported by highway only as items of
Class 9. Packaging must conform with paragraph (e)(8) of this section
with not more than 100 cells per package.
Secs. 173.201, 173.202, 173.203, 173.211, 173.212, 173.213 [Amended]
42a. In addition to the amendments set forth above, part 173 is
amended by adding the wording ``Aluminum jerrican: 3B1 or 3B2''
immediately following ``Plastic jerrican: 3H1 or 3H2'' each place it
appears in the following sections:
a. Section 173.201 (b) and (c)
b. Section 173.202 (b) and (c)
c. Section 173.203 (b) and (c)
d. Section 173.211 (b) and (c)
e. Section 173.212 (b) and (c)
f. Section 173.213 (b) and (c)
43. In Sec. 173.220, paragraph (c)(1) is revised to read as
follows:
Sec. 173.220 Internal combustion engines, self-propelled vehicles, and
mechanical equipment containing internal combustion engines or wet
batteries.
* * * * *
(c) * * *
(1) For transportation by vessel, the provisions of this subchapter
do not apply to a motor vehicle or mechanical equipment which is
electrically powered by a wet electric storage battery.
* * * * *
44. In Sec. 173.224, the table at the end of paragraph (b) is
revised to read as follows:
Sec. 173.224 Packaging and control and emergency temperatures for
self-reactive materials.
* * * * *
(b) * * *
* * * * *
Self-Reactive Substances
Identification Control temperature--( Emergency
Self-reactive substance No. Concentration--(%) Packing method deg.C) temperature Notes
(1) (2) (3).................... (4) (5)....................... (6).............. (7)
--------------------------------------------------------------------------------------------------------------------------------------------------------
Azodicarbonamide formulation type 3232 <100................... OP5 .......................... ................. 1
B, temperature controlled.
Azodicarbonamide formulation type 3224 <100................... OP6 .......................... ................. .........
C.
Azodicarbonamide formulation type 3234 <100................... OP6 .......................... ................. 1
C, temperature controlled.
Azodicarbonamide formulation type 3226 <100................... OP7 .......................... ................. .........
D.
Azodicarbonamide formulation type 3236 <100................... OP7 .......................... ................. 1
D, temperature controlled.
2,2'-Azodi(2,4-dimethyl-4- 3236 100.................... OP7 x 5...................... +5............... .........
methoxyvaleronitrile).
2,2'-Azodi(2,4- 3236 100.................... OP7 +10....................... +15.............. .........
dimethylvaleronitrile).
2,2'-Azodi(ethyl 2- 3235 100.................... OP7 +20....................... +25.............. .........
methylpropionate).
1,1-Azodi(hexahydrobenzonitrile). 3226 100.................... OP7 .......................... ................. .........
[[Page 24735]]
2,2-Azodi(isobutyronitrile)...... 3234 100.................... OP6 +40....................... +45.............. .........
2,2-Azodi(2-methylbutyronitrile). 3236 100.................... OP7 +35....................... +40.............. .........
Benzene-1,3-disulphohydrazide, as 3226 52..................... OP7 .......................... ................. .........
a paste.
Benzene sulphohydrazide.......... 3226 100.................... OP7 .......................... ................. .........
4-(Benzyl(ethyl)amino)-3- 3226 100.................... OP7 .......................... ................. .........
ethoxybenzenediazonium zinc
chloride.
4-(Benzyl(methyl)amino)-3- 3236 100.................... OP7 +40....................... +45.............. .........
ethoxybenzenediazonium zinc
chloride.
3-Chloro-4- 3226 100.................... OP7 .......................... ................. .........
diethylaminobenzenediazonium
zinc chloride.
2-Diazo-1-Naphthol-4- 3222 100.................... OP5 .......................... ................. .........
sulphochloride.
2-Diazo-1-Naphthol-5- 3222 100.................... OP5 .......................... ................. .........
sulphochloride.
2,5-Diethoxy-4- 3236 67-100................. OP7 +35....................... +40.............. .........
morpholinobenzenediazonium zinc
chloride.
2,5-Diethoxy-4- 3236 66..................... OP7 +40....................... +45.............. .........
morpholinobenzenediazonium zinc
chloride.
2,5-Diethoxy-4- 3236 100.................... OP7 +30....................... +35.............. .........
morpholinobenzenediazonium
tetrafluoroborate.
2,5-Diethoxy-4- 3236 67..................... OP7 +40....................... +45.............. .........
(phenylsulphonyl)benzenediazoniu
m zinc chloride.
Diethylene glycol bis(allyl 3237 88+42. 8. OP7......... ......... ......... 2
-48.
Acetyl acetone peroxide [as a UN3106....... 32. ....... ....... ....... ............. OP7......... ......... ......... 21
paste].
Acetyl benzoyl peroxide...... UN3105....... 45. 82. ....... ....... ....... 12 OP4......... -10...... 0
peroxide.
Acetyl cyclohexanesulfonyl UN3115....... 32. ....... 88. 6. OP8
-6.
tert-Amyl peroxyacetate...... UN3107....... 62. 96. 100 ....... ....... ....... ............. OP7......... +20...... +25
ethylhexanoate.
tert-Amyl peroxy-2-ethylhexyl UN3105....... 100 ....... ....... ....... ............. OP7
carbonate.
tert-Amyl peroxyneodecanoate. UN3115....... 77. ....... 77. ....... 100 ....... ....... ....... ............. OP5
trimethylhexanoate.
tert-Butyl cumyl peroxide.... UN3105....... -42-100....... ....... ....... ....... ............. OP7......... ......... ......... 1, 9
tert-Butyl cumyl peroxide.... UN3106....... 42. ....... 52-100....... ....... ....... ....... ............. OP5
butylperoxy)valerate.
n-Butyl-4,4-di-(tert- UN3106....... 52. ....... ....... 42. ....... ....... 79-90........ ....... ....... ....... 10 OP5......... ......... ......... 13
tert-Butyl hydroperoxide..... UN3105....... 80. 79. ....... ....... ....... >14.......... OP8......... ......... ......... 13, 16
tert-Butyl hydroperoxide..... UN3109....... 72. ....... ....... ....... 28 OP8......... ......... ......... 7, 13
tert-Butyl hydroperoxide UN3103....... <82+>9........ ....... ....... ....... 7. OP5......... ......... ......... 13
[and] Di- tert-butylperoxide.
tert-Butyl monoperoxymaleate. UN3102....... >52-100....... ....... ....... ....... ............. OP5
tert-Butyl monoperoxymaleate. UN3103....... 52. 52. ....... ....... 52. ....... ....... ....... ............. OP8 ......... ......... ............
[as a paste].
tert-Butyl monoperoxymaleate UN 3110...... 42. ....... ....... ....... ............. OP8......... ......... ......... 7
[as a paste].
tert-Butyl UN 3102...... 100 ....... ....... ....... ............. OP5 ......... ......... ............
monoperoxyphthalate.
tert-Butyl peroxyacetate..... UN 3101...... >52-77........ 32-52........ 32. 32. ....... 22. ....... 77-100....... 52-77........ 52. ....... ....... 52. 77. 100 ....... ....... ....... ............. OP5......... +20...... +25 ............
peroxydiethylacetate.
tert-Butyl UN 3105...... 33+ 52-100....... ....... ....... ....... ............. OP6......... +20...... +25 ............
ethylhexanoate.
tert-Butyl peroxy-2- UN 3117...... 52. ....... 52. ....... ....... 32. ....... 32. ....... 32. ....... 31+ ....... 12+ 100 ....... ....... ....... ............. OP7 ......... ......... ............
ethylhexylcarbonate.
tert-Butyl peroxyisobutyrate. UN 3111...... >52-77........ ....... 52. ....... 77. 77. 42. ....... ....... 100 ....... ....... ....... ............. OP5 ......... ......... ............
methylbenzoate.
tert-Butyl peroxyneodecanoate UN3115....... >77-100....... ....... ....... ....... ............. OP7......... -5....... +5 ............
tert-Butyl peroxyneodecanoate UN3115....... 77. ....... 42. ....... ....... ....... ............. OP8......... 0........ +10 ............
[as a stable dispersion in
water].
tert-Butyl peroxyneodecanoate UN3118....... 42. ....... ....... ....... ............. OP8......... 0........ +10 ............
[as a stable dispersion in
water (frozen)].
tert-Butyl UN3115....... 77. 100 ....... ....... ....... ............. OP7 ......... ......... ............
phenylphthalide.
tert-Butyl peroxypivalate.... UN3113....... >67-77........ 67. ....... 27. ....... 27. ....... 27. ....... 100 ....... ....... ....... ............. OP7 ......... ......... ............
stearylcarbonate.
tert-Butyl peroxy-3,5,5- UN3105....... >32-100....... ....... ....... ....... ............. OP7 ......... ......... ............
trimethylhexanoate.
tert-Butyl peroxy-3,5,5- UN3109....... 32. 32. ....... 57-86........ ....... ....... 77. ....... ....... 17 OP7......... ......... ......... ............
-6.
3-Chloroperoxybenzoic acid... UN3106....... 57. ....... ....... 40 OP7......... ......... ......... ............
-3.
Cumyl hydroperoxide.......... UN3107....... >90-98........ 90. 77. ....... 52. ....... ....... ....... ............. OP8......... -10...... 0 ............
a stable dispersion in
water].
Cumyl peroxyneoheptanoate.... UN3115....... 77. 77. ....... 91. ....... ....... ....... 9. OP6......... ......... ......... 13
Cyclohexanone peroxide(s).... UN3105....... 72. ....... 72. ....... ....... ....... ............. OP7......... ......... ......... 5, 21
a paste].
Cyclohexanone peroxide(s).... Exempt....... 32. ....... ....... 57. ....... 8. OP7......... +40...... +45...... 5
-26.
Diacetyl peroxide............ UN3115....... 27. ....... 100 ....... ....... ....... ............. OP8
1,1-Di-(tert- UN3103....... 82. 51-100....... ....... ....... 77-94........ ....... ....... ....... 6 OP4......... ......... ......... 3
Dibenzoyl peroxide........... UN3104....... 77. ....... ....... ....... 23 OP6
Dibenzoyl peroxide........... UN3106....... 62. ....... ....... 10 OP7
-28.
Dibenzoyl peroxide [as a UN3106....... >52-62........ ....... ....... ....... OP7......... ......... ......... 21
paste].
Dibenzoyl peroxide [as a UN3108....... 56. ....... ....... 15 OP8
paste]. 5.
Dibenzoyl peroxide........... UN3106....... >35-52........ ....... ....... 52. ....... ....... ....... ............. OP8......... ......... ......... 21
paste].
Dibenzoyl peroxide [as a Exempt....... 50. 18 Exempt
paste]. -14.
Dibenzoyl peroxide........... UN3107....... >36-42........ 40 OP8 .........
-18.
Dibenzoyl peroxide........... UN3107....... >36-42........ 42. ....... ....... ....... ............. OP8......... ......... ......... 10
stable dispersion in water].
Dibenzoyl peroxide........... Exempt....... 35. ....... ....... 87. ....... ....... ....... 13 OP5......... +25...... +30
Di-(4-tert- UN3114....... 100 ....... ....... ....... ............. OP6......... +30...... +35
butylcyclohexyl)peroxydicarb
onate.
Di-(4-tert- UN3119....... 42. ....... ....... ....... ............. OP8......... +30...... +35...... 10
butylcyclohexyl)peroxydicarb
onate [as a stable
dispersion in water].
Di-tert-butyl peroxide....... UN3107....... >32-100....... ....... ....... ....... OP8
Di-tert-butyl peroxide....... UN3109....... 52. ....... 52. 52. 80-100....... ....... ....... ....... OP5
butylperoxy)cyclohexane.
1,1-Di-(tert- UN3103....... >52-80........ 52. 42. 42. 27. 25. 13. 27-52........ ....... 42. ....... ....... ....... ............. OP8......... -15...... -5....... ............
[as a stable dispersion in
water (frozen)].
Di-n-butyl peroxydicarbonate. UN3117....... 27. ....... 52-100....... ....... ....... ....... ............. OP4......... -20...... -10...... 6
peroxydicarbonate.
Di-sec-butyl UN3115....... 52. ....... 42-100....... ....... ....... 42. ....... ....... 42-52........ 52. ....... ....... ....... ............. OP7......... ......... ......... 21
butylperoxy)phthalate [as a
paste].
Di-(tert- UN3107....... 42. 52. 42. 90-100....... ....... ....... ....... OP5
3,5,5- trimethylcyclohexane.
1,1-Di-(tert-butylperoxy)- UN3103....... >57-90........ 57. ....... ....... 57. 32. 100 ....... ....... ....... ............. OP7......... +30...... +35
Dicetyl peroxydicarbonate [as UN3119....... 42. ....... ....... ....... ............. OP8......... +30...... +35...... 10
a stable dispersion in
water].
Di-4-chlorobenzoyl peroxide.. UN3102....... 77. ....... ....... ....... 23 OP5
Di-4-chlorobenzoyl peroxide UN3106....... 52. ....... ....... ....... ............. OP7......... ......... ......... 21
[as a paste].
Di-4-chlorobenzoyl peroxide.. Exempt....... 32. ....... ....... 52-100....... ....... 52-100....... ....... ....... 52. 52. ....... ....... 91-100....... ....... ....... ....... ............. OP3......... +5....... +10 ............
peroxydicarbonate.
Dicyclohexyl UN3114....... 91. ....... ....... ....... 9. OP5......... +5....... +10...... ............
peroxydicarbonate.
Didecanoyl peroxide.......... UN3114....... 100 ....... ....... ....... ............. OP6......... +30...... +35 ............
2,2-Di-(4,4-di(tert- UN3106....... 42. ....... ....... 25. ....... 77. ....... ....... ....... 23 OP5......... ......... ......... ............
peroxide.
Di-2,4-dichlorobenzoyl UN3106....... 52. ....... ....... ....... ............. OP7......... ......... ......... ............
peroxide [as a paste with
silicone oil].
Di-(2-ethylhexyl) UN3113....... >77-100....... ....... ....... ....... ............. OP5......... -20...... -10...... ............
peroxydicarbonate.
Di-(2-ethylhexyl) UN3115....... 77. ....... ....... ....... ............. OP7......... -15...... -5 ............
peroxydicarbonate.
Di-(2-ethylhexyl) UN3119....... 52. ....... ....... ....... ............. OP8......... -15...... -5 ............
peroxydicarbonate [as a
stable dispersion in water].
Di-(2-ethylhexyl) UN3118....... 42. ....... ....... ....... ............. OP8......... -15...... -5 ............
peroxydicarbonate [as a
stable dispersion in water
(frozen)].
Diethyl peroxydicarbonate.... UN3115....... 27. 10...... 0........ ............
-73.
2,2-Dihydroperoxypropane..... UN3102....... 27. ....... ....... 100 ....... ....... ....... OP7
hydroxycyclohexyl)peroxide.
Diisobutyryl peroxide........ UN3111....... >32-52........ ....... 32. ....... 82. 5. OP7......... ......... ......... 17
dihydroperoxide. -5.
Diisopropyl peroxydicarbonate UN3112....... >52-100....... ....... ....... ....... ............. OP2......... -15...... -5 ............
[[Page 24739]]
Diisopropyl peroxydicarbonate UN3115....... 52. ....... 100 ....... ....... ....... ............. OP7 -10...... 0
peroxydicarbonate.
Dilauroyl peroxide........... UN3106....... 100 ....... ....... ....... ............. OP7
Dilauroyl peroxide [as a UN3109....... 42. ....... ....... ....... ............. OP8......... ......... ......... 10
stable dispersion in water].
Di-(2-methylbenzoyl)peroxide. UN3112....... 87. ....... ....... ....... 13 OP5......... +30...... +35...... ............
Di-(4-methylbenzoyl)peroxide UN3106....... 52. ....... ....... ....... OP7
[as a paste with silicone
oil].
2,5-Dimethyl-2,5-di- UN3102....... >82-100....... ....... ....... ....... OP5
(benzoylperoxy)hexane.
2,5-Dimethyl-2,5-di- UN3104....... 82. ....... ....... ....... 18 OP5
(benzoylperoxy)hexane.
2,5-Dimethyl-2,5-di- UN3106....... 82. ....... ....... 52-100....... ....... ....... ....... ............. OP7
butylperoxy)hexane.
2,5-Dimethyl-2,5-di-(tert- UN3101....... >87-100....... ....... ....... ....... ............. OP5
butylperoxy)hexyne-3.
2,5-Dimethyl-2,5-di-(tert- UN3103....... >52-86........ ....... ....... ....... ............. OP5
butylperoxy)hexyne-3.
2,5-Dimethyl-2,5-di-(tert- UN3106....... 52. ....... ....... 52. 52. ....... ....... 47. ....... ....... ....... ............. OP8
butylperoxy)hexane [as a
paste].
2,5-Dimethyl-2,5-di-(2- UN3115....... 100 ....... ....... ....... ............. OP7......... +20...... +25
ethylhexanoylperoxy)hexane.
2,5-Dimethyl-2,5- UN3104....... 82. ....... ....... ....... 18 ............ OP6
dihydroperoxyhexane.
2,5-Dimethyl-2,5-di-(3,5,5- UN3105....... 77. 52. ....... 100 ....... ....... ....... ............. OP7......... +20...... +25...... ............
Dimyristyl peroxydicarbonate UN3119....... 42. ....... ....... ....... ............. OP8......... +20...... +25 ............
[as a stable dispersion in
water].
Dimyristyl peroxydicarbonate UN3119....... 42. ....... ....... ....... ............. IBC......... +15...... +25...... 10
[as a stable dispersion in
water].
Di-(2- UN3115....... 52. 100 ....... ....... ....... ............. OP7......... 0........ +10 ............
Di-n-octanoyl peroxide....... UN3114....... 100 ....... ....... ....... ............. OP5......... +10...... +15 ............
Diperoxy azelaic acid........ UN3116....... 27. ....... ....... 13-42........ ....... ....... 13. ....... ....... 85-100....... ....... ....... ....... ............. OP5
phenoxyethyl)peroxydicarbona
te.
Di-(2- UN3106....... 85. ....... ....... ....... 15 OP7
phenoxyethyl)peroxydicarbona
te.
Dipropionyl peroxide......... UN3117....... 27. ....... 100 ....... ....... ....... ............. OP4......... -25...... -15...... ............
Distearyl peroxydicarbonate.. UN3106....... 87. ....... ....... 72-100....... ....... ....... ....... ............. OP4......... ......... ......... 18
Disuccinic acid peroxide..... UN3116....... 72. ....... ....... ....... 28 OP7......... +10...... +15
Di-(3,5,5-trimethyl-1,2- UN3116....... 52. ....... ....... ....... ............. OP7......... +30...... +35...... 21
dioxolanyl- 3)peroxide [as a
paste].
Di-(3,5,5- UN3115....... >38-82........ 52. ....... ....... ....... ............. OP8......... +10...... +15
trimethylhexanoyl)peroxide
[as a stable dispersion in
water].
Di-(3,5,5- UN3119....... 38. 38. 38. 67. 77 - 100..... ....... ....... ....... ............. OP5
butylperoxy)butyrate.
Ethyl 3,3-di-(tert- UN3105....... 77. 52. ....... ....... 52 - 100..... ....... ....... ....... ............. OP4
1,2,4,5- tetraoxacyclononane.
[[Page 24740]]
3,3,6,6,9,9-Hexamethyl- UN3105....... 52. 52. ....... 52 ....... ....... ....... ............. OP5......... -20...... -10
peroxydicarbonate + di-sec- + 28 + 22.
Isopropylcumyl hydroperoxide. UN3109....... 72. 72 - 100.... ....... ....... ....... ............. OP7......... ......... ......... 13
p-Menthyl hydroperoxide...... UN3109....... 72. 67. ....... 52. 45. 40. 62. 6.. ....... ....... ....... 60 Exempt...... ......... ......... ............
than 20% hydrogen peroxide.
Peracetic acid with not more UN3109....... 17. ....... ....... ....... 27 OP8......... ......... ......... 10, 13
than 26% hydrogen peroxide.
Peracetic acid with 7% UN3107....... 36. ....... ....... ....... 15 OP8......... ......... ......... 13
hydrogen peroxide.
Peroxyacetic acid, type D, UN3105....... 43. ....... ....... ....... ............. OP7......... ......... 13, 20...
stabilized.
Peroxyacetic acid, type E, UN3107....... 43. ....... ....... ....... ............. OP8......... ......... ......... 13, 20
stabilized.
Peroxyacetic acid, type F, UN3109....... 43. ....... ....... ....... ............. OP8......... ......... ......... 13, 20
stabilized.
Pinanyl hydroperoxide........ UN3105....... 56- ....... ....... ....... ............. OP7......... ......... ......... 13
100.
Pinanyl hydroperoxide........ UN3109....... <56........... >44.... ....... ....... ............. OP8......... ......... ......... 7
Tetrahydronaphthyl UN3106....... 100 ....... ....... ....... ............. OP7......... ......... ......... ............
hydroperoxide.
1,1,3,3-Tetramethylbutyl UN3105....... 100 ....... ....... ....... ............. OP7......... ......... ......... ............
hydroperoxide.
1,1,3,3- UN3115....... 100 ....... ....... ....... ............. OP7 +20...... +25...... ............
Tetramethylbutylperoxy-2-
ethylhexanoate.
2,4,4-Trimethylpentyl-2- UN3115....... 72. ....... 52. ....... ....... ....... ............. OP8 -5....... +5....... ............
peroxyneodecanoate [as a
stable dispersion in water].
2,4,4-Trimethylpentyl-2- UN3115....... 37. ....... 9 percent.
6. For domestic shipments, OP5 is authorized.
7. This material may be transported in intermediate bulk containers and bulk packagings under the provisions of paragraph (e) of this section.
8. Only non-metallic packagings are authorized.
9. For domestic shipments, this material may be transported in bulk packagings under the provisions of paragraph (e)(3)(ii) of this section.
10. This material may be transported in intermediate bulk containers under the provisions of paragraph (e) of this section.
11. Up to 2000 kg per container authorized.
12. Samples may only be offered for transportation under the provisions of paragraph (c)(4) of this section.
13. ``Corrosive'' subsidiary risk label is required.
14. This material may be transported in bulk packagings under the provisions of paragraph (e) of this section.
15. No ``Corrosive'' subsidiary risk label is required for concentrations below 80%.
16. With <6% di-tert-butyl peroxide.
17. With 8% 1-isopropylhydroperoxy-4-isopropylhydroxybenzene.
18. Addition of water to this organic peroxide will decrease its thermal stability.
19. [Reserved]
20. Mixtures with hydrogen peroxide, water and acid(s).
21. With diluent type A, with or without water.
22. With >36 percent, by mass, ethylbenzene.
[[Page 24741]]
23. With >19 percent, by mass, methyl isobutyl ketone.
24. Diluent type b with boiling point >100 C.
25. No ``Corrosive'' subsidiary risk label is required for concentrations below 56%.
* * * * *
(d) Packing Method Table. Packagings for organic peroxides and
self-reactive substances are listed in the Maximum Quantity per Packing
Method Table. The packing methods are designated OP1 to OP8. The
quantities specified for each packing method represent the maximum that
is authorized.
(1) The following types of packagings are authorized:
(i) Drums: 1A1, 1A2, 1B1, 1B2, 1D, 1G, 1H1, 1H2;
(ii) Jerricans: 3A1, 3A2, 3B1, 3B2, 3H1, 3H2;
(iii) Boxes: 4C1, 4C2, 4D, 4F, 4G, 4H1, 4H2, 4A, 4B; or
(iv) Composite packagings with a plastic inner receptacle: 6HA1,
6HA2, 6HB1, 6HB2, 6HC, 6HD1, 6HD2, 6HG1, 6HG2, 6HH1, 6HH2.
(2) Metal packaging (including inner packagings of combination
packagings and outer packagings of combination or composite packagings)
are used only for packing methods OP7 and OP8.
(3) In combination packagings, glass receptacles are used only as
inner packagings with a maximum content of 0.5 kg or 0.5 liter.
(4) The maximum quantity per packaging or package for Packing
Methods OP1-OP8 must be as follows:
Maximum Quantity Per Packaging/Package for Packing Methods OP1 to OP8
----------------------------------------------------------------------------------------------------------------
Packing method
Maximum quantity -----------------------------------------------------------------------
OP1 OP2\1\ OP3 OP4\1\ OP5 OP6 OP7 OP8
----------------------------------------------------------------------------------------------------------------
Solids and combination packagings
(liquid and solid) (kg)................ 0.5 0.5/10 5 5/25 25 50 50 \2\200
Liquids (L)............................. 0.5 ....... 5 ....... 30 60 60 \3\225
----------------------------------------------------------------------------------------------------------------
\1\ If two values are given, the first applies to the maximum net mass per inner packaging and the second to the
maximum net mass of the complete package.
\2\ 60 kg for jerricans and 100 kg for boxes.
\3\ 60 L for jerricans.
(e) * * *
(5) Intermediate bulk containers. Intermediate bulk containers that
are tested at the Packing Group II performance level in accordance with
subpart O of part 178 of this subchapter are authorized as follows:
(i) Composite: 31HA1;
(ii) Rigid plastic: 31H1; and
(iii) Metal: 31A.
Sec. 173.225 [Amended]
47. In addition, in Sec. 173.225, the following changes are made:
a. Paragraphs (c)(2) and (c)(3) are removed.
b. Paragraphs (c)(4) and (c)(5) are redesignated as paragraphs
(c)(2) and (c)(3).
c. In the first sentence in paragraph (c)(1), the reference
``(c)(4)'' is revised to read ``(c)(2)''.
d. In newly designated paragraph (c)(2)(ii), the wording ``OP2A or
OP2B, for a liquid or a solid, respectively'' is revised to read
``OP2''.
e. In paragraph (e)(2), the last sentence is removed.
f. Paragraph (e)(3)(i)(B) is removed and paragraph (e)(3)(i)(C) is
redesignated as paragraph (e)(3)(i)(B).
Sec. 173.226 [Amended]
48. In Sec. 173.226, in paragraph (c)(1), the entry ``Aluminum
jerrican: 3B2'' is added immediately following ``Plastic jerrican:
3H2''.
Sec. 173.315 [Amended]
49. In Sec. 173.315, in the paragraph (a) table, for the entry
``Methylamine, anhydrous'', the following changes are made:
a. In Column 4, the punctuation and wording ``; See Note 24.'' is
removed and a period is added in its place.
b. In Column 5, the wording ``See Note 22.'' is removed.
50. In Sec. 173.316, a new paragraph (d) is added to read as
follows:
Sec. 173.316 Cryogenic liquids in cylinders.
* * * * *
(d) Mixtures of cryogenic liquid. Where charging requirements are
not specifically prescribed in paragraph (c) of this section, the
cryogenic liquid must be shipped in packagings and under conditions
approved by the Associate Administrator for Hazardous Materials Safety.
51. In Sec. 173.318, a new paragraph (f)(4) is added to read as
follows:
Sec. 173.318 Cryogenic liquids in cargo tanks.
* * * * *
(f) * * *
(4) Mixtures of cryogenic liquid. Where charging requirements are
not specifically prescribed in this paragraph (f), the cryogenic liquid
must be shipped in packagings and under conditions approved by the
Associate Administrator for Hazardous Materials Safety.
* * * * *
Appendix E--[Removed and Reserved]
52. Appendix E to Part 173 is removed and reserved.
Appendix F--[Removed and Reserved]
53-54. Appendix F to Part 173 is removed and reserved.
PART 175--CARRIAGE BY AIRCRAFT
55. The authority citation for part 175 continues to read as
follows:
Authority: 49 U.S.C. 5101-5127; 49 CFR 1.53.
Sec. 175.10 [Amended]
56. In Sec. 175.10, in paragraph (a)(22), the wording ``or
thermometer'' is added immediately following ``barometer'' each place
it appears.
PART 176--CARRIAGE BY VESSEL
57. The authority citation for part 176 continues to read as
follows:
Authority: 49 U.S.C. 5101-5127; 49 CFR 1.53.
58.In Sec. 176.78, paragraph (k) is revised to read as follows:
Sec. 176.78 Use of power-operated industrial trucks on board vessels.
* * * * *
(k) Stowage of power-operated industrial trucks on board a vessel.
Trucks stowed on board a vessel must meet vessel stowage requirements
in Sec. 176.905.
* * * * *
[[Page 24742]]
59. In Sec. 176.84, in the paragraph (b) table, a new entry for
code 17, currently reserved, is added in numerical order to read as
follows:
Sec. 176.84 Other requirements for stowage and segregation for cargo
vessels and passenger vessels.
* * * * *
(b) * * *
------------------------------------------------------------------------
Code Provisions
------------------------------------------------------------------------
* * * * *
17............................... Segregation same as for flammable
gases but ``away from'' dangerous
when wet.
* * * * *
------------------------------------------------------------------------
* * * * *
60. Section 176.905 is revised to read as follows:
Sec. 176.905 Motor vehicles or mechanical equipment powered by
internal combustion engines.
(a) A motor vehicle or any mechanized equipment powered by an
internal combustion engine is subject to the following requirements
when carried as cargo on a vessel:
(1) Before being loaded on a vessel, each motor vehicle or
mechanical equipment must be inspected for fuel leaks and identifiable
faults in the electrical system that could result in short circuit or
other unintended electrical source of ignition. A motor vehicle or
mechanical equipment showing any signs of leakage or electrical fault
may not be transported.
(2) The fuel tank of a motor vehicle or mechanical equipment
powered by liquid fuel may not be more than one-fourth full.
(3) Whenever possible, each vehicle or mechanical equipment must be
stowed to allow for its inspection during transit.
(4) Motor vehicles or mechanical equipment may be refueled when
necessary in the hold of a vessel in accordance with Sec. 176.78.
(5) When a motor vehicle or mechanical equipment with fuel in its
tanks is stowed in a closed freight container, a warning, displayed on
a contrasting background and readily legible from a distance of 8
meters (26 feet), must be affixed to the access doors to read as
follows:
WARNING-MAY CONTAIN EXPLOSIVE MIXTURES WITH AIR--KEEP IGNITION SOURCES
AWAY WHEN OPENING
(6) A motor vehicle or mechanical equipment's ignition key may not
be in the ignition while the vehicle or mechanical equipment is stowed
aboard a vessel.
(b) All equipment used for handling vehicles or mechanical
equipment must be designed so that the fuel tank and fuel system of the
vehicle or mechanical equipment are protected from stress that might
cause rupture or other damage incident to handling.
(c) Two hand-held, portable, dry chemical fire extinguishers of at
least 4.5 kg (10 pounds) capacity each must be separately located in an
accessible location in each hold or compartment in which any motor
vehicle or mechanical equipment is stowed.
(d) ``NO SMOKING'' signs must be conspicuously posted at each
access opening to the hold or compartment.
(e) Each portable electrical light, including a flashlight, used in
the stowage area must be an approved, explosion-proof type. All
electrical connections for any portable light must be made to outlets
outside the space in which any vehicle or mechanical equipment is
stowed.
(f) Each hold or compartment must be ventilated and fitted with an
overhead water sprinkler system or fixed fire extinguishing system.
(g) Each hold or compartment must be equipped with a smoke or fire
detection system capable of alerting personnel on the bridge.
(h) All electrical equipment in the hold or compartment other than
fixed explosion-proof lighting must be disconnected from its power
source at a location outside the hold or compartment during the
handling and transportation of any vehicle or mechanical equipment.
Where the disconnecting means is a switch or circuit breaker, it must
be locked in the open position until all vehicles have been removed.
(i) Exceptions. A motor vehicle or mechanical equipment is excepted
from the requirements of this subchapter if the following requirements
are met:
(1) The motor vehicle or mechanical equipment has an internal
combustion engine using liquid fuel that has a flashpoint less than 38
deg.C (100 deg.F), the fuel tank is empty, and the engine is run until
it stalls for lack of fuel;
(2) The motor vehicle or mechanical equipment has an internal
combustion engine using liquid fuel that has a flashpoint of 38 deg.C
(100 deg.F) or higher, the fuel tank contains 418 liters (110 gallons)
of fuel or less, and there are no fuel leaks in any portion of the fuel
system;
(3) The motor vehicle or mechanical equipment is stowed in a hold
or compartment designated by the administration of the country in which
the vessel is registered to be specially suited for vehicles. See 46
CFR 70.10-44 and 90.10-38 for U.S. vessels;
(4) The motor vehicle or mechanical equipment is electrically
powered by wet electric storage batteries; or
(5) The motor vehicle or mechanical equipment is equipped with
liquefied petroleum gas or other compressed gas fuel tanks, the tanks
are completely emptied of liquid and the positive pressure in the tank
does not exceed 2 bar (29 psi), the line from the fuel tank to the
regulator and the regulator itself is drained of all trace of (liquid)
gas, and the fuel shut-off valve is closed.
(j) Except as provided in Sec. 173.220(f) of this subchapter, the
provisions of this subchapter do not apply to items of equipment such
as fire extinguishers, compressed gas accumulators, airbag inflators
and the like which are installed in the motor vehicle or mechanical
equipment if they are necessary for the operation of the vehicle or
equipment, or for the safety of its operator or passengers.
PART 178--SPECIFICATIONS FOR PACKAGINGS
61. The authority citation for part 178 continues to read as
follows:
Authority: 49 U.S.C. 5101-5127; 49 CFR 1.53.
62. In Sec. 178.511, the section heading, paragraph (a), paragraph
(b) introductory text, and paragraph (b)(1) are revised, paragraphs
(b)(2) through (b)(6) are redesignated as paragraphs (b)(3) through
(b)(7) and a new paragraph (b)(2) is added, to read as follows:
Sec. 178.511 Standards for aluminum and steel jerricans.
(a) The following are identification codes for aluminum and steel
jerricans:
(1) 3A1 for a non-removable head steel jerrican;
(2) 3A2 for a removable head steel jerrican;
(3) 3B1 for a non-removable head aluminum jerrican; and
(4) 3B2 for a removable head aluminum jerrican.
(b) Construction requirements for aluminum and steel jerricans are
as follows:
(1) For steel jerricans the body and heads must be constructed of
steel sheet of suitable type and adequate thickness in relation to the
capacity of the jerrican and its intended use. Minimum thickness and
marking requirements in Secs. 173.28(b)(4) and 178.503(a)(9) of this
subchapter apply to jerricans intended for reuse.
(2) For aluminum jerricans the body and heads must be constructed
of
[[Page 24743]]
aluminum at least 99% pure or of an aluminum base alloy. Material must
be of a type and of adequate thickness in relation to the capacity of
the jerrican and to its intended use.
* * * * *
63. In Sec. 178.703, a new paragraph (b)(6) is added to read as
follows:
Sec. 178.703 Marking of intermediate bulk containers.
* * * * *
(b) * * *
(6) For each composite intermediate bulk container, the inner
receptacle must be marked with at least the following information:
(i) The code number designating the intermediate bulk container
design type, the name and address or symbol of the manufacturer, the
date of manufacture and the country authorizing the allocation of the
mark as specified in paragraph (a) of this section;
(ii) Where the outer casing of a composite intermediate bulk
container can be dismantled, each of the detachable parts must be
marked with the month and year of manufacture and the name or symbol of
the manufacturer.
64. In Sec. 178.707, in paragraphs (c)(2) and (c)(3) introductory
text, a new sentence is added at the end of each paragraph, and a new
paragraph (c)(6) is added, to read as follows:
Sec. 178.707 Standards for composite intermediate bulk containers.
* * * * *
(c) * * *
(2) * * * The outer packaging of 31HZ2 composite intermediate bulk
containers must enclose the inner receptacles on all sides.
(3) * * * The inner receptacle of 31HZ2 composite intermediate bulk
containers must consist of at least three plies of film.
* * * * *
(6) Intermediate IBCs of type 31HZ2 must be limited to a capacity
of not more than 1,250 liters.
Sec. 178.815 [Amended]
65. In Sec. 178.815, in paragraph (c)(3), the wording ``which bear
the stacking load'' is added immediately following ``and 31HH2)''.
Issued in Washington, DC on April 17, 1997 under authority
delegated in 49 CFR Part 1.
Kelley S. Coyner,
Deputy Administrator.
[FR Doc. 97-10481 Filed 5-5-97; 8:45 am]
BILLING CODE 4910-60-P