[Federal Register Volume 62, Number 77 (Tuesday, April 22, 1997)]
[Rules and Regulations]
[Pages 19482-19483]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 97-10318]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. 95-NM-227-AD; Amendment 39-9888; AD 97-02-04]
RIN 2120-AA64
Airworthiness Directives; Airbus Model A300, A300-600, A310, and
A320 Series Airplanes
AGENCY: Federal Aviation Administration, DOT.
ACTION: Final rule; correction.
-----------------------------------------------------------------------
SUMMARY: This document corrects a typographical error that appeared in
airworthiness directive (AD) 97-02-04 that was published in the Federal
Register on January 22, 1997 (62 FR 3204). The typographical error
resulted in specification of an ``inch'' figure that does not equal the
``millimeter'' figure for a certain brake wear limit. This AD is
applicable to certain Airbus Model A300, A300-600, A310, and A320
series airplanes. This AD requires an inspection of the landing gear
brakes for wear, and replacement if the specified wear limits are not
met. That AD also requires incorporation of the specified wear limits
into the FAA-approved maintenance inspection program.
DATES: Effective February 26, 1997.
FOR FURTHER INFORMATION CONTACT: Joe Jacobsen, Aerospace Engineer,
Standardization Branch, ANM-113, FAA, Transport Airplane Directorate,
1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (206)
227-2011; fax (206) 227-1149.
SUPPLEMENTARY INFORMATION: Airworthiness Directive (AD) 97-02-04,
amendment 39-9888, applicable to Airbus Model A300, A300-600, A310, and
A320 series airplanes, was published in the Federal Register on January
22, 1997 (62 FR 3204). That AD requires an inspection of the landing
gear brakes for wear, and replacement if the specified wear limits are
not met. That AD also requires incorporation of the specified wear
limits into the FAA-approved maintenance inspection program.
As published, that AD contained a typographical error in Table 3 of
paragraph (b)(4), which requires replacement of any brake that has
measured wear beyond the maximum wear limits specified in Table 3 with
a brake that is within the wear limits. For Model A300-600 series
airplanes having Messier-Bugatti brake part number (P/N) C20175100,
Table 3 lists a maximum brake wear limit of 1.1 inch (50.0 mm).''
However, 1.1 inch equals 28.0 mm.
Since no other part of the regulatory information has been changed,
the final rule is not being republished.
The effective date of the AD remains February 26, 1997.
Sec. 39.13 [Corrected]
On page 3208, the maximum brake wear limit for Model A300-600
series airplanes having Messier-Bugatti brake P/N C20175100 listed in
Table 3 of paragraph (b)(4) of AD 97-02-04 is corrected to read as
follows:
* * * * *
(b)(4)
----------------------------------------------------------------------------------------------------------------
Maximum brake wear limit (inch/
Airplane model/series Brake manufacturer Brake part No. mm)
----------------------------------------------------------------------------------------------------------------
A300-600.......................... Messier-Bugatti..... C20175100 1.1'' (28.0 mm).
----------------------------------------------------------------------------------------------------------------
[[Page 19483]]
* * * * *
Issued in Renton, Washington, on April 16, 1997.
Darrell M. Pederson,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 97-10318 Filed 4-21-97; 8:45 am]
BILLING CODE 4910-13-U