[Federal Register Volume 60, Number 191 (Tuesday, October 3, 1995)]
[Notices]
[Page 51775]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 95-24597]



-----------------------------------------------------------------------

DEPARTMENT OF COMMERCE
[Docket A(32b1)-18-95]


Foreign-Trade Zone 172--Oneida County, NY Request for 
Manufacturing Authority for Low Complexity Manufacturing Group, Inc. 
(Copier, Laser Printer Components)

    An application has been submitted to the Foreign-Trade Zones Board 
(the Board) by the County of Oneida, New York, grantee of FTZ 172, 
pursuant to Sec. 400.32(b)(1) of the Board's regulations (15 CFR Part 
400), requesting authority on behalf of Low Complexity Manufacturing 
Group, Inc. (wholly-owned subsidiary of Xerox Corporation) (LCMG), to 
manufacture certain copier and laser printer components under zone 
procedures within FTZ 172. It was formally filed on September 20, 1995.
    The FTZ Board approved subzone status for the Xerox Corporation in 
Webster, New York, in 1983 (Subzone 23A, Board Order 220, 48 FR 35479, 
8/4/83; grant transferred to FTZ 141 as Subzone 141B on 12/27/90, Board 
Order 498, 56 FR 675, 1/8/91). In 1988, Xerox was authorized to 
manufacture laser printers in the subzone (Doc. 13-88, 7/29/88). In 
1993, Xerox started up production (similar to existing production 
activities at the Xerox Webster Subzone 141B) of certain copier and 
laser printer components to LCMG, which operates a facility within FTZ 
172. This activity had been conducted under zone procedures within FTZ 
SZ 141B, and authority is now being sought to use zone procedures for 
this activity at FTZ 172.
    The LCMG facility in FTZ 172 is currently used for the manufacture 
and remanufacture of copier and laser printer cartridge replacement 
units and related components. Certain materials would be sourced from 
abroad, including: trim blade assembly, corotron wire assembly, 
magnetic roller, charge scorotron assembly, screws, washers, springs, 
gears, photoreceptors, filters, packaging, bearings, and toner (duty 
rates: 0-8.1%). The finished subassemblies include printer cartridges 
with and without toner fill, mag roll assemblies, and copy machine 
subassemblies with photoreceptor.
    Zone procedures would exempt LCMG from Customs duty payments on the 
foreign materials used in export manufacture. On domestic shipments, 
LCMG would be allowed to choose the duty rates that apply to finished 
cartridges and assemblies (0-3.5%) instead of the rates that would 
otherwise apply to the foreign materials (0-8.1%). The application 
indicates that zone procedures for this activity would contribute to 
the company's overall international competitiveness.
    Public comments on the application is invited from interested 
parties. Submissions (original and three copies) shall be addressed to 
the Board's Executive Secretary at the address below. The closing 
period of their receipt is November 2, 1995. Rebuttal comments in 
response to material submitted during the foregoing period may be 
submitted during the subsequent 15-day period to November 17, 1995.
    A copy of the application and the accompanying exhibits will be 
available for public inspection at the following location: Office of 
the Executive Secretary, Foreign-Trade Zones Board, Room 3716, U.S. 
Department of Commerce, 14th & Pennsylvania Avenue, NW, Washington, DC 
20230.

    Dated: September 26, 1995.
John J. Da Ponte, Jr.,
Executive Secretary.
[FR Doc. 95-24597 Filed 10-2-95; 8:45 am]
BILLING CODE 3510-DS-P