[Federal Register Volume 59, Number 125 (Thursday, June 30, 1994)]
[Unknown Section]
[Page 0]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 94-15596]
[[Page Unknown]]
[Federal Register: June 30, 1994]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
14 CFR Part 39
[Docket No. 93-NM-143-AD; Amendment 39-8954; AD 94-14-02]
Airworthiness Directives; Boeing Model 757 Series Airplanes
Equipped With Rolls Royce RB211-535C Engines
AGENCY: Federal Aviation Administration, DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: This amendment adopts a new airworthiness directive (AD),
applicable to certain Boeing Model 757 series airplanes, that requires
tests of the thrust reverser system, and repair, if necessary;
installation of a modification that would terminate those tests; and
repetitive operational checks of that installation, and repair, if
necessary. This amendment is prompted by results of a safety review,
which revealed that in-flight deployment of a thrust reverser could
result in a significant reduction in the controllability of the
airplane. The actions specified by this AD are intended to prevent
deployment of a thrust reverser in flight and subsequent reduced
controllability of the airplane.
DATES: Effective August 1, 1994.
The incorporation by reference of certain publications listed in
the regulations is approved by the Director of the Federal Register as
of August 1, 1994.
ADDRESSES: The service information referenced in this AD may be
obtained from Boeing Commercial Airplane Group, P.O. Box 3707, Seattle,
Washington 98124-2207; and Rolls-Royce plc, P.O. Box 31, Derby DE24
8BJ, England, ATTN: Technical Publications Department. This information
may be examined at the Federal Aviation Administration (FAA), Transport
Airplane Directorate, Rules Docket, 1601 Lind Avenue, SW., Renton,
Washington; or at the Office of the Federal Register, 800 North Capitol
Street, NW., suite 700, Washington, DC.
FOR FURTHER INFORMATION CONTACT: Jeffrey Duven, Aerospace Engineer,
Propulsion Branch, ANM-140S, FAA, Transport Airplane Directorate,
Seattle Aircraft Certification Office, 1601 Lind Avenue, SW., Renton,
Washington 98055-4056; telephone (206) 227-2688; fax (206) 227-1181.
SUPPLEMENTARY INFORMATION: A proposal to amend part 39 of the Federal
Aviation Regulations (14 CFR part 39) to include an airworthiness
directive (AD) that is applicable to certain Boeing Model 757 series
airplanes was published in the Federal Register on October 4, 1993 (58
FR 51589). That action proposed to require tests of the thrust reverser
system, and repair, if necessary; installation of a modification that
would terminate those tests; and repetitive operational checks of that
installation, and repair, if necessary. -
Interested persons have been afforded an opportunity to participate
in the making of this amendment. Due consideration has been given to
the comments received.
One commenter supports the proposed rule. -
Boeing requests that specific references to page numbers and
revision dates of the Boeing 757 Airplane Maintenance Manual (AMM) be
eliminated from the proposed rule, and that the proposal be amended to
include copies of the required test procedures so that reference to the
AMM would not be necessary. -
Boeing explains that the AMM's are customized for each operator to
reflect all of the equipment in that operator's fleet. Therefore, the
number of pages for any given procedure is variable, depending on the
number of different equipment configurations documented in an
operator's AMM. Boeing also indicates that AMM procedures are revised
periodically for non-technical reasons. Boeing adds that changes to the
structure of the procedures are necessary to accommodate an upgrade of
the publishing system that is currently under way, which, in addition
to repagination, will necessitate the issuance of revised AMM pages. -
Boeing states that the effect of specifying AMM page numbers and
revision dates in the AD is that operators may be unable to use the
procedure contained in the AMM to perform certain tests required by the
AD. Each operator would be required to maintain an obsolete version of
the procedure, or to request FAA approval of an alternative method of
compliance with the AD that would allow the use of the current version
of the AMM.
The FAA concurs partially. In light of the information submitted by
the commenter, the FAA finds that specific AMM page numbers and dates
should not be specified in the final rule. Therefore, such references
have been removed from paragraphs (a)(1) and (a)(2) of the final rule.
However, for those paragraphs, the FAA does not agree that copies of
the specific procedures should be included in the final rule.
Therefore, paragraphs (a)(1) and (a)(2) of the final rule have been
revised to cite only the appropriate section and task title specified
in the AMM for accomplishment of the tests required by those
paragraphs.
The FAA's objective in proposing periodic operational checks of the
sync-lock device, as specified in paragraph (c) of this AD, is to
ensure the integrity of the locking function. However, subsequent to
the issuance of the proposal and the receipt of Boeing's comments to
the proposal, Boeing has submitted to the FAA separate procedures for
accomplishment of the operational check of the sync-lock integrity.
These procedures have been defined in paragraph (c) of the final rule;
therefore, the AMM references specified in paragraph (c) of the NPRM
have been removed from the final rule. Additionally, the procedures for
the operational checks are accomplished independently of the other
thrust reverser system tests specified in the proposal. Accordingly,
the FAA has revised paragraph (c) of the final rule to require periodic
accomplishment of operational checks of the sync-lock integrity only,
and has removed the requirement for accomplishment of other tests
specified in that paragraph of the proposal. -
The Air Transport Association (ATA) of America, on behalf of its
members, states that, while ATA members are not opposed to
accomplishing the operational checks specified in paragraph (c) of the
proposal as part of their maintenance programs, these members are
opposed to accomplishing the checks as part of the requirements of an
AD. The commenters believe that the adoption of paragraph (c), as
proposed, is equivalent to issuing a Certification Maintenance
Requirements (CMR) item by means of an AD. -
ATA adds that, if the FAA finds sufficient justification to include
the requirement for operational checks in the AD, an alternative to
accomplishment of the checks should be provided in the final rule. ATA
reasons that an alternative is justified because no data exist to show
that repetitive checks of a modified thrust reverser cannot be handled
adequately through an operator's maintenance program. The suggested
alternative follows: Within 3 months after accomplishing the sync-lock
installation, revise the FAA- approved maintenance inspection program
to include an operational check of the sync-lock. The initial check
would be accomplished within 1,000 hours time-in-service after
modification. The AD would no longer be applicable for operators that
have acceptably revised the maintenance program. Operators choosing
this alternative could use an alternative recordkeeping method in lieu
of that required by Federal Aviation Regulation (FAR) 91.417 or 121.380
(14 CFR 91.417 or 121.380). The FAA would be defined as the cognizant
Principal Maintenance Inspector (PMI) for operators electing this
alternative.
One commenter, Boeing, requests that the proposed requirement for
operational checks be removed from the AD until the FAA reviews the
``more comprehensive'' scheduled maintenance recommendations developed
by the Model 757/767 Thrust Reverser Working Group, which will be
recommended in the next revision to the Maintenance Review Board (MRB)
report. Boeing believes that adoption of the maintenance
recommendations contained in that forthcoming revision will ensure that
an adequate level of safety (with regard to the sync-lock installation)
will be maintained by all operators of Model 757 series airplanes.
The FAA recognizes the concerns of these commenters regarding the
requirement for periodic operational checks of the sync-lock following
its installation. However, the FAA finds that the operational checks
are necessary in order to provide an adequate level of safety and to
ensure the integrity of the sync-lock installation. The actions
required by this AD are consistent with actions that have been
identified by an industry-wide task force as necessary to ensure
adequate safety of certain thrust reverser systems installed on
transport category airplanes. Representatives of the Aerospace
Industries Association (AIA) of America, Inc., and the FAA comprise
that task force. Representatives from other organizations, such as ATA,
have participated in various discussions and work activities resulting
from the recommendations of the task force.
The FAA acknowledges that the operational checks specified in this
AD and CMR items are similar in terms of scheduled maintenance and
recordkeeping. This AD addresses an unsafe condition and requires
installation of the sync-lock to correct that unsafe condition. The FAA
has determined that the requirement for operational checks is necessary
in order to ensure the effectiveness of that installation in addressing
the unsafe condition. This determination is based on the fact that the
sync-lock is a new design whose reliability has not been adequately
proven through service experience. In addition, service experience to
date has demonstrated that failures can occur within the sync-lock that
may not be evident during normal operation of the thrust reverser
system and may not result in activation of the sync-lock ``unlock''
indicator. The ATA's suggested alternative to accomplishment of the
operational checks would permit each operator to determine whether and
how often these checks should be conducted. In light of the severity of
the unsafe condition, however, the FAA has determined that allowing
this degree of operator discretion is not appropriate at this time.
Therefore, this AD is necessary to ensure that operators accomplish
checks of the integrity of the sync-lock installation in a common
manner and at common intervals.
The FAA also finds that addressing operational checks of the sync-
lock integrity in a recommended action, such as an MRB report, will not
ensure an acceptable level of safety with regard to the thrust reverser
system. However, the FAA recognizes that an operational check interval
of 4,000 hours time-in-service, which will be recommended by Boeing for
inclusion in the next revision to the MRB report, corresponds more
closely to the interval at which most of the affected operators conduct
regularly scheduled ``C'' checks. The FAA has reconsidered the proposed
interval of 1,000 hours time-in-service for accomplishment of
repetitive operational checks. In light of the safety implications of
the unsafe condition addressed and the practical aspects of
accomplishing orderly operational checks of the fleet during regularly
scheduled maintenance where special equipment and trained maintenance
personnel will be readily available, the FAA finds that accomplishment
of the checks at intervals of 4,000 hours time-in-service will provide
an acceptable level of safety. Paragraph (c) of the final rule has been
revised accordingly.
Since the issuance of the proposed rule, Boeing has issued Revision
2 of Service Bulletin 757-78-0035, dated June 23, 1994. The service
bulletin revision moves general work instruction Step B from Work
Package 2 to Step Q in Work Package 8. In Revision 1 of the service
bulletin, Step B of Work Package 2 specified procedures for removal of
the ground to the EICAS for the REV ISLN VAL message; however, the
ground should not be removed as part of Work Package 2. Rather, the
ground should be removed as part of Work Package 8 in order to avoid
loss of the REV ISLN VAL message on EICAS. Revision 2 of the service
bulletin correctly describes procedures for removal of the ground as
part of Work Package 8. Revision 2 of the service bulletin also
describes procedures for installation of an additional bracket on the
P36 disconnect bracket and to make a cutout on the P37 disconnect
bracket on certain airplanes.
The FAA has reviewed and approved this latest revision to the
service bulletin and has revised the final rule to reflect it as the
appropriate source of service information. The FAA finds that citing
this latest revision to the service bulletin will impose no additional
burden on any operator.
It should be noted that Revision 2 of Boeing Service Bulletin 757-
78-0035 references Rolls-Royce Service Bulletins RB.211-78-9725 and
RB.211-78-9726 as additional sources of service information for
accomplishment of the originally proposed sync-lock installation.
However, the Boeing service bulletin does not specify the appropriate
revision levels for the Rolls-Royce service bulletins. Therefore, the
FAA has added ``NOTE 1'' to paragraph (b) of this AD to specify that
the intent of that paragraph is that the appropriate revision levels
for the Rolls-Royce service bulletins that are to be used in
conjunction with Boeing Service Bulletin 757-78-0035 are as follows:
Rolls-Royce Service Bulletin RB.211-78-9725, dated June 23, 1993, or
Revision 1, dated January 7, 1994; and Rolls-Royce Service Bulletin
RB.211-78-9726, dated June 23, 1993, or Revision 1, dated October 1,
1993.
In addition, since the issuance of the proposed rule, Rolls-Royce
has issued Service Bulletin RB.211-78-9822, dated October 1, 1993. This
service bulletin describes procedures for installation of a revised
thrust reverser sync-lock. The FAA has determined that accomplishment
of the actions described in this service bulletin, in conjunction with
Boeing Service Bulletin 757-78-0035 [which was cited in paragraph (b)
of the proposal as the appropriate source of service information for
installation of an additional thrust reverser system locking feature],
constitutes an acceptable alternative to the sync-lock installation
specified in paragraph (b) of the proposal.
In light of this information, paragraph (b) of the final rule has
been revised to include paragraph (b)(1), which contains the
requirement for installation of an additional thrust reverser system
locking feature that was specified in the proposed rule, and paragraph
(b)(2), which provides for installation of a revised thrust reverser
sync-lock as an acceptable alternative to paragraph (b)(1) of this AD.
Accomplishment of the revised installation specified in paragraph
(b)(2) requires no additional work hours beyond the 514 work hours
specified in the economic impact information, below, for accomplishment
of the originally proposed sync-lock installation.
Additionally, it should be noted that Rolls-Royce Service Bulletin
RB.211-78-9822 references Rolls-Royce Service Bulletin RB.211-78-9726
as an additional source of service information for airplanes equipped
with Rolls-Royce RB211-535C engines. Rolls-Royce Service Bulletin
RB.211-78-9726 references Rolls-Royce Service Bulletin RB.211-78-9725
as an additional source of service information. However, the
appropriate revision levels for these service bulletins are not
specified in Boeing Service Bulletin 757-78-0035 or in any of the
Rolls-Royce service bulletins. Therefore, the FAA has added ``NOTE 2''
to paragraph (b) of the final rule to specify that the appropriate
revision levels for Rolls-Royce Service Bulletins RB.211-78-9726 and
RB.211-78-9725, used in conjunction with Rolls-Royce Service Bulletin
RB.211-78-9822, are as follows: Rolls-Royce Service Bulletin RB.211-78-
9726, dated June 23, 1993, or Revision 1, dated October 1, 1993; and
Rolls-Royce Service Bulletin RB.211-78-9725, dated June 23, 1993, or
Revision 1, dated January 7, 1994.
After careful review of the available data, including the comments
noted above, the FAA has determined that air safety and the public
interest require the adoption of the rule with the changes previously
described. The FAA has determined that these changes will neither
increase the economic burden on any operator nor increase the scope of
the AD.
There are approximately 40 Model 757 series airplanes of the
affected design in the worldwide fleet. Currently, there are no Model
757 series airplanes of the affected design on the U.S. Register.
However, should an affected airplane be imported and placed on the U.S.
Register in the future, it will take approximately 1 work hour per
airplane to accomplish the required auto restow and integrity tests,
514 work hours per airplane to accomplish either modification specified
in paragraph (b)(1) or (b)(2) of this AD, and 1 work hour per airplane
to accomplish the required operational checks; at an average labor rate
of $55 per work hour. Required parts are currently planned to be
supplied by the manufacturer at no cost to operators. Based on these
figures, the total cost impact of the AD is estimated to be $28,380 per
airplane.
The regulations adopted herein will not have substantial direct
effects on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, in
accordance with Executive Order 12612, it is determined that this final
rule does not have sufficient federalism implications to warrant the
preparation of a Federalism Assessment.
For the reasons discussed above, I certify that this action (1) is
not a ``significant regulatory action'' under Executive Order 12866;
(2) is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and (3) will not have a
significant economic impact, positive or negative, on a substantial
number of small entities under the criteria of the Regulatory
Flexibility Act. A final evaluation has been prepared for this action
and it is contained in the Rules Docket. A copy of it may be obtained
from the Rules Docket at the location provided under the caption
ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration amends part 39 of
the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. App. 1354(a), 1421 and 1423; 49 U.S.C.
106(g); and 14 CFR 11.89.
Sec. 39.13 [Amended]
2. Section 39.13 is amended by adding the following new
airworthiness directive:
94-14-02 Boeing: Amendment 39-8954. Docket 93-NM-143-AD.
Applicability: Model 757 series airplanes equipped with Rolls
Royce RB211-535C engines, as listed in Boeing Service Bulletin 757-
78-0035, Revision 2, dated June 23, 1994; certificated in any
category.
Compliance: Required as indicated, unless accomplished
previously.
To prevent deployment of a thrust reverser in flight and
subsequent reduced controllability of the airplane, accomplish the
following:
(a) For airplanes on which the sync-lock feature has not been
installed as a modification in accordance with Boeing Service
Bulletin 757-78-0035: Within 4,000 hours time-in-service after the
effective date of this AD; and thereafter at intervals not to exceed
4,000 hours time-in-service until the modification required by
paragraph (b) of this AD is accomplished; accomplish paragraphs
(a)(1) and (a)(2) of this AD to verify proper operation of the
thrust reverser system. Prior to further flight, repair any
discrepancy found, in accordance with the procedures described in
the Boeing 757 Maintenance Manual.
(1) Perform a ``Thrust Reverser-Auto Restow Test'' in accordance
with the procedures described in Section 78-31-00 of the Boeing 757
Maintenance Manual.
(2) Perform an ``Actuator Lock and Crossover Shaft Integrity
Test'' in accordance with the procedures described in Section 78-31-
00 of the Boeing 757 Maintenance Manual.
(b) For airplanes on which the sync-lock feature has not been
installed as a modification in accordance with Boeing Service
Bulletin 757-78-0035: Within 5 years after the effective date of
this AD, accomplish the requirements of paragraph (b)(1) or (b)(2)
of this AD. Accomplishment of either of these installations
constitutes terminating action for the tests required by paragraph
(a) of this AD.
(1) Install an additional thrust reverser system locking feature
(sync-lock installation) in accordance with Boeing Service Bulletin
757-78-0035, Revision 2, dated June 23, 1994.
Note 1: Boeing Service Bulletin 757-78-0035 references Rolls-
Royce Service Bulletins RB.211-78-9725 and RB.211-78-9726 as
additional sources of service information. The intent of paragraph
(b)(1) of this AD is that the appropriate revision levels for the
Rolls-Royce service bulletins that are to be used in conjunction
with Boeing Service Bulletin 757-78-0035 are as follows: Rolls-Royce
Service Bulletin RB.211-78-9725, dated June 23, 1993, or Revision 1,
dated January 7, 1994; and Rolls-Royce Service Bulletin RB.211-78-
9726, dated June 23, 1993, or Revision 1, dated October 1, 1993.
(2) Install a revised thrust reverser sync-lock in accordance
with Boeing Service Bulletin 757-78-0035, Revision 2, dated June 23,
1994, and Rolls-Royce Service Bulletin RB.211-78-9822, dated October
1, 1993.
Note 2: Rolls-Royce Service Bulletin RB.211-78-9822 references
Rolls-Royce Service Bulletin RB.211-78-9726 as an additional source
of service information for airplanes equipped with Rolls-Royce
RB211-535C engines. Rolls-Royce Service Bulletin RB.211-78-9726
references Rolls-Royce Service Bulletin RB.211-78-9725 as an
additional source of service information. The FAA's intent is that
the appropriate revision levels of Rolls-Royce Service Bulletins
RB.211-78-9726 and RB.211-78-9725, used in conjunction with Rolls-
Royce Service Bulletin RB.211-78-9822, are as follows: Rolls-Royce
Service Bulletin RB.211-78-9726, dated June 23, 1993, or Revision 1,
dated October 1, 1993; and Rolls-Royce Service Bulletin RB.211-78-
9725, dated June 23, 1993, or Revision 1, dated January 7, 1994.
(c) Within 4,000 hours time-in-service after accomplishing the
modification required by paragraph (b) of this AD, or within 4,000
hours time-in-service after the effective date of this AD, whichever
occurs later; and thereafter at intervals not to exceed 4,000 hours
time-in-service: Accomplish the thrust reverser sync-lock integrity
test defined below to verify that the sync-locks have not failed in
the ``unlocked'' state. Prior to further flight, repair any
discrepancy found, in accordance with procedures described in the
Boeing 757 Maintenance Manual.
Thrust Reverser Sync-Lock Integrity Test
1. General
A. Use this procedure to test the integrity of the thrust
reverser sync locks. The procedure must be performed on each engine.
2. Thrust Reverser Sync Lock Test
A. Prepare for the thrust reverser sync lock test.
(1) Open the AUTO SPEEDBRAKE circuit breaker on the overhead
circuit breaker panel, P11.
(2) Do the steps that follow to supply power to the thrust
reverser system:
(a) Make sure the thrust levers are in the idle position.
(b) Make sure the thrust reversers are retracted and locked.
(c) Make sure these circuit breakers on the main power
distribution panel, P6, are closed:
(1) L ENG SYNC LOCK
(2) R ENG SYNC LOCK-ALTN
(d) Make sure these circuit breakers on the overhead circuit
breaker panel, P11, are closed:
(1) LANDING GEAR POS SYS 1
(2) T/R IND R
(3) T/R CONT-ALTN-R
(4) T/R IND L
(5) T/R CONT L
(6) R ENG SYNC LOCK
(7) T/R CONT R
(8) EICAS CMPTR LEFT
(9) EICAS UPPER IND
(10) EICAS CMPTR RIGHT
(11) EICAS LOWER IND
(12) EICAS DISPLAY SW
(13) EICAS PILOTS DSP
(14) AIR/GND SYS 1
(15) AIR/GND SYS 2
(16) LANDING GEAR POS SYS 2
(17) PROX SW TEST
(e) Supply electrical power.
(f) Supply pressure to the left (for the left engine) or right
(for the right engine) hydraulic system.
B. Do the thrust reverser sync lock test.
(1) Use the SENSOR CHANNEL SELECT thumb switches to set the PSEU
code for the auto-restow proximity sensor.
(a) On PSEU (-17), The left engine code is 433.
(b) On PSEU (-16), The left engine code is 105.
(c) The right engine PSEU code is 099.
Note: The following step will cause the Hydraulic Isolation
Valve (HIV) to open for approximately 5 seconds. The next 3 steps
must be done during this 5 second time. These 4 steps may be
repeated if required.
(2) Push the TARGET TEST switch on the PSEU and hold for one
second.
(3) Make sure the TARGET NEAR light on the PSEU comes on after
approximately four seconds.
(4) Make sure that the EICAS Advisory message L(R) REV ISLN VAL
shows for approximately 3 seconds and then does not show.
(5) Make sure the sync lock manual unlock lever on the right
sleeve of the reverser does not extend.
(6) Push and release the RESET switch on the PSEU.
(7) Open the applicable circuit breaker(s):
(a) For the left engine; L ENG SYNC LOCK (Panel P6)
(b) For the right engine; R ENG SYNC LOCK (Panel P11) R ENG SYNC
LOCK-ALTN (Panel P6)
(8) Move the left (right) reverse thrust lever up and rearward
to the reverse thrust position.
(9) Make sure that the thrust reverser does not extend.
(10) Move the left (right) reverse thrust lever to the forward
and down position.
C. Put the airplane back to its usual condition.
(1) Remove hydraulic pressure.
(2) Close the applicable circuit breaker(s).
(a) For the left engine; L ENG SYNC LOCK (Panel P6)
(b) For the right engine; R ENG SYNC LOCK (Panel P11) R ENG SYNC
LOCK-ALTN (Panel P6)
(3) Close the AUTO SPEEDBRAKE circuit breaker on the overhead
circuit breaker panel, P11.
(4) Remove electrical power.
D. Repeat the thrust reverser sync lock test on the other
engine.
(d) An alternative method of compliance or adjustment of the
compliance time that provides an acceptable level of safety may be
used if approved by the Manager, Seattle Aircraft Certification
Office (ACO), FAA, Transport Airplane Directorate. Operators shall
submit their requests through an appropriate FAA Principal
Maintenance Inspector, who may add comments and then send it to the
Manager, Seattle ACO.
Note 3: Information concerning the existence of approved
alternative methods of compliance with this AD, if any, may be
obtained from the Seattle ACO.
(e) Special flight permits may be issued in accordance with
sections 21.197 and 21.199 of the Federal Aviation Regulations (14
CFR 21.197 and 21.199) to operate the airplane to a location where
the requirements of this AD can be accomplished.
(f) The installation shall be done in accordance with Boeing
Service Bulletin 757-78-0035, Revision 2, dated June 23, 1994; and
Rolls-Royce Service Bulletin RB.211-78-9822, dated October 1, 1993.
This incorporation by reference was approved by the Director of the
Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part
51. Copies may be obtained from Boeing Commercial Airplane Group,
P.O. Box 3707, Seattle, Washington 98124-2207; and Rolls-Royce plc,
P.O. Box 31, Derby DE24 8BJ, England, ATTN: Technical Publications
Department. Copies may be inspected at the FAA, Transport Airplane
Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the
Office of the Federal Register, 800 North Capitol Street, NW., suite
700, Washington, DC.
(g) This amendment becomes effective on August 1, 1994.
Issued in Renton, Washington, on June 22, 1994.
S.R. Miller,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 94-15596 Filed 6-29-94; 8:45 am]
BILLING CODE 4910-13-U