[Title 40 CFR ]
[Code of Federal Regulations (annual edition) - July 1, 1998 Edition]
[From the U.S. Government Printing Office]


[[Page 1]]

          40



          Protection of Environment



          PART 52 (Secs. 52.01--52.1018)

                         Revised as of July 1, 1998

          CONTAINING
          A CODIFICATION OF DOCUMENTS
          OF GENERAL APPLICABILITY
          AND FUTURE EFFECT
          AS OF JULY 1, 1998

          With Ancillaries
          Published by
          the Office of the Federal Register
          National Archives and Records
          Administration
          as a Special Edition of
          the Federal Register



[[Page ii]]

                                      




                     U.S. GOVERNMENT PRINTING OFFICE
                            WASHINGTON : 1998



               For sale by U.S. Government Printing Office
 Superintendent of Documents, Mail Stop: SSOP, Washington, DC 20402-9328



[[Page iii]]




                            Table of Contents



                                                                    Page
  Explanation.................................................       v

  Title 40:
    Chapter I--Environmental Protection Agency (Continued)....       3
  Finding Aids:
    Material Approved for Incorporation by Reference..........     531
    Table of CFR Titles and Chapters..........................     543
    Alphabetical List of Agencies Appearing in the CFR........     561
    Table of OMB Control Numbers..............................     571
    List of CFR Sections Affected.............................     591



[[Page iv]]


      


--------------------------------------------------------------------

   Cite this Code:  CFR

   To cite the regulations in this volume use title, part and
   section number. Thus,  40 CFR 52.01 refers to title 40, part
   52, section 01.

--------------------------------------------------------------------


[[Page v]]



                               EXPLANATION

    The Code of Federal Regulations is a codification of the general and 
permanent rules published in the Federal Register by the Executive 
departments and agencies of the Federal Government. The Code is divided 
into 50 titles which represent broad areas subject to Federal 
regulation. Each title is divided into chapters which usually bear the 
name of the issuing agency. Each chapter is further subdivided into 
parts covering specific regulatory areas.
    Each volume of the Code is revised at least once each calendar year 
and issued on a quarterly basis approximately as follows:

Title 1 through Title 16.................................as of January 1
Title 17 through Title 27..................................as of April 1
Title 28 through Title 41...................................as of July 1
Title 42 through Title 50................................as of October 1
    The appropriate revision date is printed on the cover of each 
volume.

LEGAL STATUS

    The contents of the Federal Register are required to be judicially 
noticed (44 U.S.C. 1507). The Code of Federal Regulations is prima facie 
evidence of the text of the original documents (44 U.S.C. 1510).

HOW TO USE THE CODE OF FEDERAL REGULATIONS

    The Code of Federal Regulations is kept up to date by the individual 
issues of the Federal Register. These two publications must be used 
together to determine the latest version of any given rule.
    To determine whether a Code volume has been amended since its 
revision date (in this case, July 1, 1998), consult the ``List of CFR 
Sections Affected (LSA),'' which is issued monthly, and the ``Cumulative 
List of Parts Affected,'' which appears in the Reader Aids section of 
the daily Federal Register. These two lists will identify the Federal 
Register page number of the latest amendment of any given rule.

EFFECTIVE AND EXPIRATION DATES

    Each volume of the Code contains amendments published in the Federal 
Register since the last revision of that volume of the Code. Source 
citations for the regulations are referred to by volume number and page 
number of the Federal Register and date of publication. Publication 
dates and effective dates are usually not the same and care must be 
exercised by the user in determining the actual effective date. In 
instances where the effective date is beyond the cut-off date for the 
Code a note has been inserted to reflect the future effective date. In 
those instances where a regulation published in the Federal Register 
states a date certain for expiration, an appropriate note will be 
inserted following the text.

OMB CONTROL NUMBERS

    The Paperwork Reduction Act of 1980 (Pub. L. 96-511) requires 
Federal agencies to display an OMB control number with their information 
collection request.

[[Page vi]]

Many agencies have begun publishing numerous OMB control numbers as 
amendments to existing regulations in the CFR. These OMB numbers are 
placed as close as possible to the applicable recordkeeping or reporting 
requirements.

OBSOLETE PROVISIONS

    Provisions that become obsolete before the revision date stated on 
the cover of each volume are not carried. Code users may find the text 
of provisions in effect on a given date in the past by using the 
appropriate numerical list of sections affected. For the period before 
January 1, 1986, consult either the List of CFR Sections Affected, 1949-
1963, 1964-1972, or 1973-1985, published in seven separate volumes. For 
the period beginning January 1, 1986, a ``List of CFR Sections 
Affected'' is published at the end of each CFR volume.

INCORPORATION BY REFERENCE

    What is incorporation by reference? Incorporation by reference was 
established by statute and allows Federal agencies to meet the 
requirement to publish regulations in the Federal Register by referring 
to materials already published elsewhere. For an incorporation to be 
valid, the Director of the Federal Register must approve it. The legal 
effect of incorporation by reference is that the material is treated as 
if it were published in full in the Federal Register (5 U.S.C. 552(a)). 
This material, like any other properly issued regulation, has the force 
of law.
    What is a proper incorporation by reference? The Director of the 
Federal Register will approve an incorporation by reference only when 
the requirements of 1 CFR part 51 are met. Some of the elements on which 
approval is based are:
    (a) The incorporation will substantially reduce the volume of 
material published in the Federal Register.
    (b) The matter incorporated is in fact available to the extent 
necessary to afford fairness and uniformity in the administrative 
process.
    (c) The incorporating document is drafted and submitted for 
publication in accordance with 1 CFR part 51.
    Properly approved incorporations by reference in this volume are 
listed in the Finding Aids at the end of this volume.
    What if the material incorporated by reference cannot be found? If 
you have any problem locating or obtaining a copy of material listed in 
the Finding Aids of this volume as an approved incorporation by 
reference, please contact the agency that issued the regulation 
containing that incorporation. If, after contacting the agency, you find 
the material is not available, please notify the Director of the Federal 
Register, National Archives and Records Administration, Washington DC 
20408, or call (202) 523-4534.

CFR INDEXES AND TABULAR GUIDES

    A subject index to the Code of Federal Regulations is contained in a 
separate volume, revised annually as of January 1, entitled CFR Index 
and Finding Aids. This volume contains the Parallel Table of Statutory 
Authorities and Agency Rules (Table I), and Acts Requiring Publication 
in the Federal Register (Table II). A list of CFR titles, chapters, and 
parts and an alphabetical list of agencies publishing in the CFR are 
also included in this volume.
    An index to the text of ``Title 3--The President'' is carried within 
that volume.
    The Federal Register Index is issued monthly in cumulative form. 
This index is based on a consolidation of the ``Contents'' entries in 
the daily Federal Register.

[[Page vii]]

    A List of CFR Sections Affected (LSA) is published monthly, keyed to 
the revision dates of the 50 CFR titles.

REPUBLICATION OF MATERIAL

    There are no restrictions on the republication of material appearing 
in the Code of Federal Regulations.

INQUIRIES

    For a legal interpretation or explanation of any regulation in this 
volume, contact the issuing agency. The issuing agency's name appears at 
the top of odd-numbered pages.
    For inquiries concerning CFR reference assistance, call 202-523-5227 
or write to the Director, Office of the Federal Register, National 
Archives and Records Administration, Washington, DC 20408.

SALES

    The Government Printing Office (GPO) processes all sales and 
distribution of the CFR. For payment by credit card, call 202-512-1800, 
M-F, 8 a.m. to 4 p.m. e.s.t. or fax your order to 202-512-2233, 24 hours 
a day. For payment by check, write to the Superintendent of Documents, 
Attn: New Orders, P.O. Box 371954, Pittsburgh, PA 15250-7954. For GPO 
Customer Service call 202-512-1803.

ELECTRONIC SERVICES

    The full text of the Code of Federal Regulations, The United States 
Government Manual, the Federal Register, Public Laws, Weekly Compilation 
of Presidential Documents and the Privacy Act Compilation are available 
in electronic format at www.access.gpo.gov/nara (``GPO Access''). For 
more information, contact Electronic Information Dissemination Services, 
U.S. Government Printing Office. Phone 202-512-1530, or 888-293-6498 
(toll-free). E-mail, [email protected].
    The Office of the Federal Register also offers a free service on the 
National Archives and Records Administration's (NARA) World Wide Web 
site for public law numbers, Federal Register finding aids, and related 
information. Connect to NARA's web site at www.nara.gov/fedreg. The NARA 
site also contains links to GPO Access.

                              Raymond A. Mosley,
                                    Director,
                          Office of the Federal Register.

July 1, 1998.



[[Page ix]]



                               THIS TITLE

    Title 40--Protection of Environment is composed of twenty-three 
volumes. The parts in these volumes are arranged in the following order: 
parts 1-49, parts 50-51, parts 52.01-52.1018, part 52.1019-end, parts 
53-59, part 60, parts 61-62, part 63, parts 64-71, parts 72-80, parts 
81-85, part 86, parts 87-135, parts 136-149, parts 150-189, parts 190-
259, parts 260-265, parts 266-299, parts 300-399, parts 400-424, parts 
425-699, parts 700-789, and part 790 to end. The contents of these 
volumes represent all current regulations codified under this title of 
the CFR as of July 1, 1998.

    Chapter I--Environmental Protection Agency appears in all twenty-two 
volumes. A Pesticide Tolerance Commodity/Chemical Index appears in parts 
150-189. A Toxic Substances Chemical--CAS Number Index appears in parts 
700-789 and part 790 to end. Redesignation Tables appear in the volumes 
containing parts 50-51, parts 150-189, and parts 700-789. Regulations 
issued by the Council on Environmental Quality appear in the volume 
containing part 790 to end.

    The OMB control numbers for title 40 appear in Sec. 9.1 of this 
chapter. For the convenience of the user, Sec. 9.1 appears in the 
Finding Aids section of the volumes containing part 50 to the end.

    For this volume, Gregory R. Walton was Chief Editor. The Code of 
Federal Regulations publication program is under the direction of 
Frances D. McDonald, assisted by Alomha S. Morris.

[[Page x]]




[[Page 1]]



                   TITLE 40--PROTECTION OF ENVIRONMENT




                      (This book contains part 52)

  --------------------------------------------------------------------

                                                                    Part

Chapter i--Environmental Protection Agency (Continued)......          52

[[Page 3]]



         CHAPTER I--ENVIRONMENTAL PROTECTION AGENCY (CONTINUED)




  --------------------------------------------------------------------

                 SUBCHAPTER C--AIR PROGRAMS--(Continued)

Part                                                                Page
52              Approval and promulgation of implementation 
                    plans...................................           5


  Editorial Note:  Subchapter C--Air programs is contained in volumes 40 
CFR parts 50-51, part 52.01-52.1018, part 52.1019-End, parts 53-59, part 
60, parts 61-62, part 63, parts 64-71, parts 72-80, parts 81-85, part 
86, and parts 87-135.

[[Page 5]]



                 SUBCHAPTER C--AIR PROGRAMS--(CONTINUED)





PART 52--APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS--Table of Contents




                      Subpart A--General Provisions

Sec.
52.01  Definitions.
52.02  Introduction.
52.04  Classification of regions.
52.05  Public availability of emission data.
52.06  Legal authority.
52.07  Control strategies.
52.08  Rules and regulations.
52.09  Compliance schedules.
52.10  Review of new sources and modifications.
52.11  Prevention of air pollution emergency episodes.
52.12  Source surveillance.
52.13  Air quality surveillance; resources; intergovernmental 
          cooperation.
52.14  State ambient air quality standards.
52.15  Public availability of plans.
52.16  Submission to Administrator.
52.17  Severability of provisions.
52.18  Abbreviations.
52.20  Attainment dates for national standards.
52.21  Prevention of significant deterioration of air quality.
52.23  Violation and enforcement.
52.24  Statutory restriction on new sources.
52.26  Visibility monitoring strategy.
52.27  Protection of visibility from sources in attainment areas.
52.28  Protection of visibility from sources in nonattainment areas.
52.29  Visibility long-term strategies.
52.30  Criteria for limiting application of sanctions under section 
          110(m) of the Clean Air Act on a statewide basis.
52.31  Selection of sequence of mandatory sanctions for findings made 
          pursuant to section 179 of the Clean Air Act.
52.32  Sanctions following findings of SIP inadequacy.
52.33  Compliance certifications.

                           Subpart B--Alabama

52.50  Identification of plan.
52.51  Classification of regions.
52.53  Approval status.
52.56  Review of new sources and modifications.
52.57  Control strategy: Sulfur oxides.
52.58  Control strategy: Lead.
52.60  Significant deterioration of air quality.
52.61  Visibility protection.
52.62  Control strategy: Sulfur oxides and particulate matter.
52.63  PM10 State Implementation Plan development in group II 
          areas.
52.64  [Reserved]
52.65  Control strategy: Nitrogen oxides.
52.66  Control strategy: Ozone.

                            Subpart C--Alaska

52.70  Identification of plan.
52.71  Classification of regions.
52.72  Approval status.
52.73--52.74  [Reserved]
52.75  Contents of the approved state-submitted implementation plan.
52.76  1990 Base Year Emission Inventory.
52.77--52.81  [Reserved]
52.82  Extensions.
52.83--52.95  [Reserved]
52.96  Significant deterioration of air quality.

                           Subpart D--Arizona

52.111  Toll free number assignment.
52.120  Identification of plan.
52.121  Classification of regions.
52.122  [Reserved]
52.123  Approval status.
52.124  Part D disapproval.
52.125  Control strategy and regulations: Sulfur oxides.
52.126  Control strategy and regulations: Particulate matter.
52.127--52.128  [Reserved]
52.129  Review of new sources and modifications.
52.130  Source surveillance.
52.131--52.132  [Reserved]
52.133  Rules and regulations.
52.134  Compliance schedules.
52.135  Resources.
52.136  Control strategy for ozone: Oxides of nitrogen.
52.137  [Reserved]
52.138  Conformity procedures.
52.139  [Reserved]
52.140  Monitoring transportation trends.
52.141--52.143  [Reserved]
52.144  Significant deterioration of air quality.
52.145  Visibility protection.
52.146  Particulate matter (PM-10) Group II SIP commitments.
52.150  Yavapai-Apache Reservation.

                           Subpart E--Arkansas

52.170  Identification of plan.
52.171  Classification of regions.
52.172  Approval status.
52.173--52.180  [Reserved]
52.181  Significant deterioration of air quality.
52.183  Small business assistance program.

[[Page 6]]

                          Subpart F--California

52.219  Identification of plan--conditional approval.
52.220  Identification of plan.
52.221  Classifications of regions.
52.222  Negative declarations.
52.223  Approval status.
52.224  General requirements.
52.225  Legal authority.
52.226  Control strategy and regulations: Particulate matter, San 
          Joaquin Valley and Mountain Counties Intrastate Regions.
52.227  Control strategy and regulations: Particulate matter, 
          Metropolitan Los Angeles Intrastate Region.
52.228  Regulations: Particulate matter, Southeast Desert Intrastate 
          Region.
52.229  Control strategy and regulations: Photochemical oxidants 
          (hydrocarbons), Metropolitan Los Angeles Intrastate Region.
52.230  Control strategy and regulations: Nitrogen dioxide.
52.231  Regulations: Sulfur oxides.
52.232  Part D conditional approval.
52.233  Review of new sources and modifications.
52.234  Source surveillance.
52.235  Control strategy for ozone: Oxides of nitrogen.
52.236  Rules and regulations.
52.237  Part D disapproval.
52.238  Commitment to undertake rulemaking.
52.239  Alternate compliance plans.
52.240  Compliance schedules.
52.241  Interim approval of enhanced inspection and maintenance program.
52.242  [Reserved]
52.243  Interim approval of the Carbon Monoxide plan for the South 
          Coast.
Secs. 52.244--52.245  [Reserved]
52.246  Control of dry cleaning solvent vapor losses.
52.247--52.251  [Reserved]
52.252  Control of degreasing operations.
52.253  Metal surface coating thinner and reducer.
52.254  Organic solvent usage.
52.255  Gasoline transfer vapor control.
52.256  Control of evaporative losses from the filling of vehicular 
          tanks.
52.257--52.262  [Reserved]
52.263  Priority treatment for buses and carpools--Los Angeles Region.
52.264--52.268  [Reserved]
52.269  Control strategy and regulations: Photochemical oxidants 
          (hydrocarbons) and carbon monoxide.
52.270  Significant deterioration of air quality.
52.271  Malfunction regulations.
52.272  Research operations exemptions.
52.273  Open burning.
52.274  California air pollution emergency plan.
52.275  Particulate matter control.
52.276  Sulfur content of fuels.
52.277  Oxides of nitrogen, combustion gas concentration limitations.
52.278  Oxides of nitrogen control.
52.279  Food processing facilities.
52.280  Fuel burning equipment.
52.281  Visibility protection.

                           Subpart G--Colorado

52.320  Identification of plan.
52.321  Classification of regions.
52.322  Extensions.
52.323  Approval status.
52.324  Legal authority.
52.325  [Reserved]
52.326  Area-wide nitrogen oxides (NOX) exemptions.
52.327--52.328  [Reserved]
52.329  Rules and regulations.
52.330  Control strategy: Total suspended particulates.
52.331  Committal SIP for the Colorado Group II PM10 areas.
52.332  Moderate PM-10 nonattainment area plans.
52.333--52.342  [Reserved]
52.343  Significant deterioration of air quality.
52.344  Visibility protection.
52.345  Stack height regulations.
52.346  Air quality monitoring requirements.
52.347  [Reserved]
52.348  Emission inventories.

                         Subpart H--Connecticut

52.370  Identification of plan.
52.371  Classification of regions.
52.372  Extensions.
52.373  Approval status.
52.374  Attainment dates for national standards.
52.375  Certification of no sources.
52.376  Control strategy: Carbon monoxide.
52.377--52.379  [Reserved]
52.380  Rules and regulations.
52.381  Requirements for State implementation plan revisions relating to 
          new motor vehicles.
52.382  Significant deterioration of air quality.
52.383  Stack height review.
52.384  Emission inventories.
52.385  EPA-approved Connecticut regulations.

                           Subpart I--Delaware

52.420  Identification of plan.
52.421  Classification of regions.
52.422  Approval status.
52.423  1990 Base Year Emission Inventory.
52.424  Conditional approval.
52.425--52.429  [Reserved]

[[Page 7]]

52.430  Photochemical assessment monitoring stations (PAMS) program.
52.431  [Reserved]
52.432  Significant deterioration of air quality.
52.433  Requirements for State implementation plan revisions relating to 
          new motor vehicles.
52.460  Small business stationary source technical and environmental 
          compliance assistance program.

                     Subpart J--District of Columbia

52.470  Identification of plan.
52.471  Classification of regions.
52.472  Approval status.
52.473  Conditional approval.
52.474  1990 Base Year Emission Inventory.
52.475--52.478  [Reserved]
52.479  Source surveillance.
52.480  Photochemical assessment monitoring stations (PAMS) program.
52.481--52.497  [Reserved]
52.498  Requirements for State implementation plan revisions relating to 
          new motor vehicles.
52.499  Significant deterioration of air quality.
52.510  Small business assistance program.

                           Subpart K--Florida

52.520  Identification of plan.
52.521  Classification of regions.
52.522  Approval status.
52.523  [Reserved]
52.524  Compliance schedules.
52.525  General requirements.
52.526  Legal authority.
52.527  Control strategy: General.
52.528  Control strategy: Sulfur oxides and particulate matter.
52.529  [Reserved]
52.530  Significant deterioration of air quality.
52.532  Extensions.
52.533  Source surveillance.
52.534  Visibility protection.

                           Subpart L--Georgia

52.570  Identification of plan.
52.571  Classification of regions.
52.572  Approval status.
52.573  Control strategy: General.
52.574--52.575  [Reserved]
52.576  Compliance schedules.
52.577  [Reserved]
52.578  Control strategy: Sulfur oxides and particulate matter.
52.579  Economic feasibility considerations.
52.580  [Reserved]
52.581  Significant deterioration of air quality.
52.582  Control strategy: Ozone.
52.583  Additional rules and regulations.

                            Subpart M--Hawaii

52.620  Identification of plan.
52.621  Classification of regions.
52.622  [Reserved]
52.623  Approval status.
52.624  General requirements.
52.625  Legal authority.
52.626  Compliance schedules.
52.627--52.631  [Reserved]
52.632  Significant deterioration of air quality.
52.633  Visibility protection.
52.634  Particulate matter (PM-10) Group III SIP.

                            Subpart N--Idaho

52.670  Identification of plan.
52.671  Classification of regions.
52.672  [Reserved]
52.673  Approval status.
52.674  Legal authority.
52.675  Control strategy: Sulfur oxides--Eastern Idaho Intrastate Air 
          Quality Control Region.
52.676--52.678  [Reserved]
52.679  Contents of Idaho State implementation plan.
52.680  [Reserved]
52.681  Permits to construct and operating permits.
52.682  [Reserved]
52.683  Significant deterioration of air quality.
52.684--52.689  [Reserved]
52.690  Visibility protection.
52.691  Extensions.

                           Subpart O--Illinois

52.719  Identification of plan--conditional approval.
52.720  Identification of plan.
52.721  Classification of regions.
52.722  Approval status.
52.723  [Reserved]
52.724  Control strategy: Sulfur dioxide.
52.725  Control strategy: Particulates.
52.726  Control strategy: Ozone.
52.727  [Reserved]
52.728  Control strategy: Nitrogen dioxide. [Reserved]
52.729  Control strategy: Carbon monoxide.
52.730  Compliance schedules.
52.731--52.735  [Reserved]
52.736  Review of new sources and modifications.
52.737  Operating permits.
52.738  Significant deterioration of air quality.
52.739  Permit fees.
52.740  Interstate pollution.
52.741  Control strategy: Ozone control measures for Cook, DuPage, Kane, 
          Lake, McHenry and Will Counties.
52.742  Incorporation by reference.

[[Page 8]]

52.743  Continuous monitoring.
52.744  Small business stationary source technical and environmental 
          compliance assistance program.

                           Subpart P--Indiana

52.769  Identification of plan--conditional approval.
52.770  Identification of plan.
52.771  Classification of regions.
52.772  [Reserved]
52.773  Approval status.
52.774  [Reserved]
52.775  Legal authority.
52.776  Control strategy: Particulate matter.
52.777  Control strategy: Photochemical oxidants (hydrocarbons).
52.778  Compliance schedules.
52.779  [Reserved]
52.780  Review of new sources and modifications.
52.781  Rules and regulations.
52.782  Request for 18-month extension.
52.783  [Reserved]
52.784  Transportation and land use controls.
52.785  Control strategy: Carbon monoxide.
52.786  Inspection and maintenance program.
52.787  Gasoline transfer vapor control.
52.788  Operating permits.
52.789--52.792  [Reserved]
52.793  Significant deterioration of air quality.
52.794  Source surveillance.
52.795  Control strategy: Sulfur dioxide.
52.796  Industrial continuous emission monitoring.
52.797  Control strategy: Lead.
52.798  Small business stationary source technical and environmental 
          compliance assistance program.

                             Subpart Q--Iowa

52.820  Identification of plan.
52.821  Classification of regions.
52.822  Approval status.
52.823  PM10 State Implementation Plan Development in Group 
          II Areas.
52.824  [Reserved]
52.825  Compliance schedules.
52.826--52.827  [Reserved]
52.828  Enforcement.
52.829--52.832  [Reserved]
52.833  Significant deterioration of air quality.
52.834  Control strategy: Sulfur dioxide.

                            Subpart R--Kansas

52.870  Identification of plan.
52.871  Classification of regions.
52.872  Operating permits.
52.873  Approval status.
52.874  Legal authority.
52.875  [Reserved]
52.876  Compliance schedules.
52.877--52.880  [Reserved]
52.881  PM10 State implementation plan development in group 
          II areas.
52.882--52.883  [Reserved]
52.884  Significant deterioration of air quality.

                           Subpart S--Kentucky

52.920  Identification of plan.
52.921  Classification of regions.
52.922  [Reserved]
52.923  Approval status.
52.924  Legal authority.
52.925  General requirements.
52.926  Attainment dates for national standards.
52.927  Compliance schedules.
52.928  Control strategy: Sulphur oxides.
52.929  [Reserved]
52.930  Control strategy: Ozone.
52.931  Significant deterioration of air quality.
52.932  Rules and regulations.
52.933  Control strategy: Sulfur oxides and particulate matter.
52.934  VOC rule deficiency correction.
52.935  PM10 State implementation plan development in group 
          II areas.
52.936  Visibility protection.
52.937  Review of new sources and modifications.

                          Subpart T--Louisiana

52.970  Identification of plan.
52.971  Classification of regions.
52.972--52.974  [Reserved]
52.975  Redesignations and maintenance plans; ozone.
52.976  Review of new sources and modification.
52.977--52.985  [Reserved]
52.986  Significant deterioration of air quality.
52.987  Control of hydrocarbon emissions.
52.988  [Reserved]
52.990  Stack height regulations
52.991  Small business assistance program.
52.992  Area-wide nitrogen oxides exemptions.
52.993  Emissions inventories.
52.994  [Reserved]
52.995  Enhanced ambient air quality monitoring.
52.996  Disapprovals.

    Authority:  42 U.S.C. 7401 et seq.



                      Subpart A--General Provisions

    Source:  37 FR 10846, May 31, 1972, unless otherwise noted.



Sec. 52.01  Definitions.

    All terms used in this part but not defined herein shall have the 
meaning

[[Page 9]]

given them in the Clean Air Act and in parts 51 and 60 of this chapter.
    (a) The term stationary source means any building, structure, 
facility, or installation which emits or may emit an air pollutant for 
which a national standard is in effect.
    (b) The term commenced means that an owner or operator has 
undertaken a continuous program of construction or modification.
    (c) The term construction means fabrication, erection, or 
installation.
    (d) The phrases modification or modified source mean any physical 
change in, or change in the method of operation of, a stationary source 
which increases the emission rate of any pollutant for which a national 
standard has been promulgated under part 50 of this chapter or which 
results in the emission of any such pollutant not previously emitted, 
except that:
    (1) Routine maintenance, repair, and replacement shall not be 
considered a physical change, and
    (2) The following shall not be considered a change in the method of 
operation:
    (i) An increase in the production rate, if such increase does not 
exceed the operating design capacity of the source;
    (ii) An increase in the hours of operation;
    (iii) Use of an alternative fuel or raw material, if prior to the 
effective date of a paragraph in this part which imposes conditions on 
or limits modifications, the source is designed to accommodate such 
alternative use.
    (e) The term startup means the setting in operation of a source for 
any purpose.
    (f) [Reserved]
    (g) The term heat input means the total gross calorific value (where 
gross calorific value is measured by ASTM Method D2015-66, D240-64, or 
D1826-64) of all fuels burned.
    (h) The term total rated capacity means the sum of the rated 
capacities of all fuel-burning equipment connected to a common stack. 
The rated capacity shall be the maximum guaranteed by the equipment 
manufacturer or the maximum normally achieved during use, whichever is 
greater.
[37 FR 19807, Sept. 22, 1972, as amended at 38 FR 12698, May 14, 1973; 
39 FR 42514, Dec. 5, 1974; 43 FR 26410, June 19, 1978]



Sec. 52.02  Introduction.

    (a) This part sets forth the Administrator's approval and 
disapproval of State plans and the Administrator's promulgation of such 
plans or portions thereof. Approval of a plan or any portion thereof is 
based upon a determination by the Administrator that such plan or 
portion meets the requirements of section 110 of the Act and the 
provisions of part 51 of this chapter.
    (b) Any plan or portion thereof promulgated by the Administrator 
substitutes for a State plan or portion thereof disapproved by the 
Administrator or not submitted by a State, or supplements a State plan 
or portion thereof. The promulgated provisions, together with any 
portions of a State plan approved by the Administrator, constitute the 
applicable plan for purposes of the Act.
    (c) Where nonregulatory provisions of a plan are disapproved, the 
disapproval is noted in this part and a detailed evaluation is provided 
to the State, but no substitute provisions are promulgated by the 
Administrator.
    (d) All approved plans and plan revisions listed in subparts B 
through DDD of this part and on file at the Office of the Federal 
Register are approved for incorporation by reference by the Director of 
the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 
51. Notice of amendments to the plans will be published in the Federal 
Register. The plans and plan revisions are available for inspection at 
the Office of the Federal Register, 800 North Capitol Street, N.W., 
suite 700, Washington, D.C. In addition the plans and plan revisions are 
available at the following locations:
    (1) Office of Air and Radiation, Docket and Information Center (Air 
Docket), EPA, 401 M Street, S.W., Room M1500, Washington, D.C. 20460.
    (2) The appropriate EPA Regional Office as listed below:
    (i) Connecticut, Maine, Massachusetts, New Hampshire, Rhode Island,

[[Page 10]]

and Vermont. Environmental Protection Agency, Region 1, John F. Kennedy 
Federal Building, One Congress Street, Boston, MA 02203.
    (ii) New York, New Jersey, Puerto Rico, and Virgin Islands. 
Environmental Protection Agency, Region 2, 290 Broadway, New York, NY 
10007-1866.
    (iii) Delaware, District of Columbia, Pennsylvania, Maryland, 
Virginia, and West Virginia. Environmental Protection Agency, Region 3, 
841 Chestnut Building, Philadelphia, PA 19107.
    (iv) Alabama, Florida, Georgia, Kentucky, Mississippi, North 
Carolina, South Carolina, and Tennessee Environmental Protection Agency, 
Region 4, 345 Courtland Street, N.E., Atlanta, GA 30365.
    (v) Illinois, Indiana, Michigan, Minnesota, Ohio, and Wisconsin. 
Environmental Protection Agency, Region 5, 77 West Jackson Boulevard, 
Chicago, IL 60604-3507.
    (vi) Arkansas, Louisiana, New Mexico, Oklahoma, and Texas. 
Environmental Protection Agency, Region 6, Fountain Place, 1445 Ross 
Avenue, Suite 1200, Dallas TX 75202-2733.
    (vii) Iowa, Kansas, Missouri, and Nebraska. Environmental Protection 
Agency, Region 7, 726 Minnesota Avenue, Kansas City, KS 66101.
    (viii) Colorado, Montana, North Dakota, South Dakota, Utah, and 
Wyoming. Environmental Protection Agency, Region 8, 999 18th Street, 
Suite 500, Denver, CO 80202-2466.
    (ix) Arizona, California, Hawaii, Nevada, American Samoa, and Guam. 
Environmental Protection Agency, Region 9, 75 Hawthorne Street, San 
Francisco, CA 94105.
    (x) Alaska, Idaho, Oregon, and Washington. Environmental Protection 
Agency, Region 10, 1200 6th Avenue Seattle, WA 98101.
    (e) Each State's plan is dealt with in a separate subpart, which 
includes an introductory section identifying the plan by name and the 
date of its submittal, a section classifying regions, and a section 
setting forth dates for attainment of the national standards. Additional 
sections are included as necessary to specifically identify disapproved 
provisions, to set forth reasons for disapproval, and to set forth 
provisions of the plan promulgated by the Administrator. Except as 
otherwise specified, all supplemental information submitted to the 
Administrator with respect to any plan has been submitted by the 
Governor of the State.
    (f) Revisions to applicable plans will be included in this part when 
approved or promulgated by the Administrator.
[37 FR 10846, May 31, 1972, as amended at 37 FR 15080, July 27, 1972; 47 
FR 38886, Sept. 3, 1982; 61 FR 16060, Apr. 11, 1996]



Sec. 52.04  Classification of regions.

    Each subpart sets forth the priority classification, by pollutant, 
for each region in the State. Each plan for each region was evaluated 
according to the requirements of part 51 of this chapter applicable to 
regions of that priority.



Sec. 52.05  Public availability of emission data.

    Each subpart sets forth the Administrator's disapproval of plan 
procedures for making emission data available to the public after 
correlation with applicable emission limitations, and includes the 
promulgation of requirements that sources report emission data to the 
Administrator for correlation and public disclosure.



Sec. 52.06  Legal authority.

    (a) The Administrator's determination of the absence or inadequacy 
of legal authority required to be included in the plan is set forth in 
each subpart. This includes the legal authority of local agencies and 
State governmental agencies other than an air pollution control agency 
if such other agencies are assigned responsibility for carrying out a 
plan or portion thereof.
    (b) No legal authority as such is promulgated by the Administrator. 
Where required regulatory provisions are not included in the plan by the 
State because of inadequate legal authority, substitute provisions are 
promulgated by the Administrator.
[37 FR 10846, May 31, 1972, as amended at 60 FR 33922, June 29, 1995]



Sec. 52.07  Control strategies.

    (a) Each subpart specifies in what respects the control strategies 
are approved or disapproved. Where emission limitations with a future 
effective date

[[Page 11]]

are employed to carry out a control strategy, approval of the control 
strategy and the implementing regulations does not supersede the 
requirements of subpart N of this chapter relating to compliance 
schedules for individual sources or categories of sources. Compliance 
schedules for individual sources or categories of sources must require 
such sources to comply with applicable requirements of the plan as 
expeditiously as practicable, where the requirement is part of a control 
strategy designed to attain a primary standard, or within a reasonable 
time, where the requirement is part of a control strategy designed to 
attain a secondary standard. All sources must be required to comply with 
applicable requirements of the plan no later than the date specified in 
this part for attainment of the national standard which the requirement 
is intended to implement.
    (b) A control strategy may be disapproved as inadequate because it 
is not sufficiently comprehensive, although all regulations provided to 
carry out the strategy may themselves be approved. In this case, 
regulations for carrying out necessary additional measures are 
promulgated in the subpart.
    (c) Where a control strategy is adequate to attain and maintain a 
national standard but one or more of the regulations to carry it out is 
not adopted or not enforceable by the State, the control strategy is 
approved and the necessary regulations are promulgated by the 
Administrator.
    (d) Where a control strategy is adequate to attain and maintain air 
quality better than that provided for by a national standard but one or 
more of the regulations to carry it out is not adopted or not 
enforceable by the State, the control strategy is approved and 
substitute regulations necessary to attain and maintain the national 
standard are promulgated.
[37 FR 10846, May 31, 1972, as amended at 37 FR 19807, Sept. 22, 1972; 
51 FR 40676, Nov. 7, 1986]



Sec. 52.08  Rules and regulations.

    Each subpart identifies the regulations, including emission 
limitations, which are disapproved by the Administrator, and includes 
the regulations which the Administrator promulgates.



Sec. 52.09  Compliance schedules.

    (a) In each subpart, compliance schedules disapproved by the 
Administrator are identified, and compliance schedules promulgated by 
the Administrator are set forth.
    (b) Individual source compliance schedules submitted with certain 
plans have not yet been evaluated, and are not approved or disapproved.
    (c) The Administrator's approval or promulgation of any compliance 
schedule shall not affect the responsibility of the owner or operator to 
comply with any applicable emission limitation on and after the date for 
final compliance specified in the applicable schedule.
[37 FR 10846, May 31, 1972, as amended at 38 FR 30877, Nov. 8, 1973]



Sec. 52.10  Review of new sources and modifications.

    In any plan where the review procedure for new sources and source 
modifications does not meet the requirements of subpart I of this 
chapter, provisions are promulgated which enable the Administrator to 
obtain the necessary information and to prevent construction or 
modification.
[37 FR 10846, May 31, 1972, as amended at 51 FR 40677, Nov. 7, 1986]



Sec. 52.11  Prevention of air pollution emergency episodes.

    (a) Each subpart identifies portions of the air pollution emergency 
episode contingency plan which are disapproved, and sets forth the 
Administrator's promulgation of substitute provisions.
    (b) No provisions are promulgated to replace any disapproved air 
quality monitoring or communications portions of a contingency plan, but 
detailed critiques of such portions are provided to the State.
    (c) Where a State plan does not provide for public announcement 
regarding air pollution emergency episodes or where the State fails to 
give any such public announcement, the Administrator will issue a public 
announcement that an episode stage has been

[[Page 12]]

reached. When making such an announcement, the Administrator will be 
guided by the suggested episode criteria and emission control actions 
suggested in Appendix L of part 51 of this chapter or those in the 
approved plan.
[37 FR 10846, May 31, 1972, as amended at 37 FR 19807, Sept. 22, 1972]



Sec. 52.12  Source surveillance.

    (a) Each subpart identifies the plan provisions for source 
surveillance which are disapproved, and sets forth the Administrator's 
promulgation of necessary provisions for requiring sources to maintain 
records, make reports, and submit information.
    (b) No provisions are promulgated for any disapproved State or local 
agency procedures for testing, inspection, investigation, or detection, 
but detailed critiques of such portions are provided to the State.
    (c) For purposes of Federal enforcement, the following test 
procedures and methods shall be used, provided that for the purpose of 
establishing whether or not a person has violated or is in violation of 
any provision of the plan, nothing in this part shall preclude the use, 
including the exclusive use, of any credible evidence or information, 
relevant to whether a source would have been in compliance with 
applicable requirements if the appropriate performance or compliance 
test procedures or methods had been performed:
    (1) Sources subject to plan provisions which do not specify a test 
procedure and sources subject to provisions promulgated by the 
Administrator will be tested by means of the appropriate procedures and 
methods prescribed in part 60 of this chapter unless otherwise specified 
in this part.
    (2) Sources subject to approved provisions of a plan wherein a test 
procedure is specified will be tested by the specified procedure.
[37 FR 10846, May 31, 1972, as amended at 40 FR 26032, June 20, 1975; 62 
FR 8328, Feb. 24, 1997]



Sec. 52.13  Air quality surveillance; resources; intergovernmental cooperation.

    Disapproved portions of the plan related to the air quality 
surveillance system, resources, and intergovernmental cooperation are 
identified in each subpart, and detailed critiques of such portions are 
provided to the State. No provisions are promulgated by the 
Administrator.



Sec. 52.14  State ambient air quality standards.

    Any ambient air quality standard submitted with a plan which is less 
stringent than a national standard is not considered part of the plan.



Sec. 52.15  Public availability of plans.

    Each State shall make available for public inspection at least one 
copy of the plan in at least one city in each region to which such plan 
is applicable. All such copies shall be kept current.



Sec. 52.16  Submission to Administrator.

    (a) All requests, reports, applications, submittals, and other 
communications to the Administrator pursuant to this part shall be 
submitted in duplicate and addressed to the appropriate Regional Office 
of the Environmental Protection Agency.
    (b) The Regional Offices are as follows:
    (1) Connecticut, Maine, Massachusetts, New Hampshire, Rhode Island, 
and Vermont. EPA Region 1, John F. Kennedy Federal Building, One 
Congress Street, Boston, MA 02203.
    (2) New York, New Jersey, Puerto Rico, and Virgin Islands. EPA 
Region 2, 290 Broadway, New York, NY 10007-1866.
    (3) Delaware, District of Columbia, Pennsylvania, Maryland, 
Virginia, and West Virginia. EPA Region 3, 841 Chestnut Building, 
Philadelphia, PA 19107.
    (4) Alabama, Florida, Georgia, Kentucky, Mississippi, North 
Carolina, South Carolina, and Tennessee. EPA Region 4, 345 Courtland 
Street, N.E., Atlanta, GA 30365.
    (5) Illinois, Indiana, Michigan, Minnesota, Ohio, and Wisconsin. EPA 
Region 5, 77 West Jackson Boulevard, Chicago, IL 60604-3507.
    (6) Arkansas, Louisiana, New Mexico, Oklahoma, and Texas. EPA Region 
6, Fountain Place, 1445 Ross Avenue, Suite 1200, Dallas, TX 75202-2733.

[[Page 13]]

    (7) Iowa, Kansas, Missouri, and Nebraska. EPA Region 7, 726 
Minnesota Avenue, Kansas City, KS 66101.
    (8) Colorado, Montana, North Dakota, South Dakota, Utah, and 
Wyoming. EPA Region 8, 999 18th Street, Suite 500, Denver, CO 80202-
2466.
    (9) Arizona, California, Hawaii, Nevada, American Samoa, and Guam. 
EPA, Region 9, 75 Hawthorne Street, San Francisco, CA 94105.
    (10) Alaska, Idaho, Oregon, and Washington. EPA, Region 10, 1200 6th 
Avenue, Seattle, WA 98101.
[61 FR 16061, Apr. 11, 1996]



Sec. 52.17  Severability of provisions.

    The provisions promulgated in this part and the various applications 
thereof are distinct and severable. If any provision of this part or the 
application thereof to any person or circumstances is held invalid, such 
invalidity shall not affect other provisions or application of such 
provision to other persons or circumstances which can be given effect 
without the invalid provision or application.
[37 FR 19808, Sept. 22, 1972]



Sec. 52.18  Abbreviations.

    Abbreviations used in this part shall be those set forth in part 60 
of this chapter.
[38 FR 12698, May 14, 1973]



Sec. 52.20  Attainment dates for national standards.

    Each subpart contains a section which specifies the latest dates by 
which national standards are to be attained in each region in the State. 
An attainment date which only refers to a month and a year (such as July 
1975) shall be construed to mean the last day of the month in question. 
However, the specification of attainment dates for national standards 
does not relieve any State from the provisions of subpart N of this 
chapter which require all sources and categories of sources to comply 
with applicable requirements of the plan--
    (a) As expeditiously as practicable where the requirement is part of 
a control strategy designed to attain a primary standard, and
    (b) Within a reasonable time where the requirement is part of a 
control strategy designed to attain a secondary standard.
[37 FR 19808, Sept. 22, 1972, as amended at 39 FR 34535, Sept. 26, 1974; 
51 FR 40676, Nov. 7, 1986]



Sec. 52.21  Prevention of significant deterioration of air quality.

    (a) Plan disapproval. The provisions of this section are applicable 
to any State implementation plan which has been disapproved with respect 
to prevention of significant deterioration of air quality in any portion 
of any State where the existing air quality is better than the national 
ambient air quality standards. Specific disapprovals are listed where 
applicable, in subparts B through DDD of this part. The provisions of 
this section have been incorporated by reference into the applicable 
implementation plans for various States, as provided in subparts B 
through DDD of this part. Where this section is so incorporated, the 
provisions shall also be applicable to all lands owned by the Federal 
Goverment and Indian Reservations located in such State. No disapproval 
with respect to a State's failure to prevent significant deterioration 
of air quality shall invalidate or otherwise affect the obligations of 
States, emission sources, or other persons with respect to all portions 
of plans approved or promulgated under this part.
    (b) Definitions. For the purposes of this section:
    (1)(i) Major stationary source means:
    (a) Any of the following stationary sources of air pollutants which 
emits, or has the potential to emit, 100 tons per year or more of any 
pollutant subject to regulation under the Act: Fossil fuel-fired steam 
electric plants of more than 250 million British thermal units per hour 
heat input, coal cleaning plants (with thermal dryers), kraft pulp 
mills, portland cement plants, primary zinc smelters, iron and steel 
mill plants, primary aluminum ore reduction plants, primary copper 
smelters, municipal incinerators capable of charging more than 250 tons 
of refuse per day, hydrofluoric, sulfuric, and nitric acid plants, 
petroleum refineries, lime plants, phosphate rock processing

[[Page 14]]

plants, coke oven batteries, sulfur recovery plants, carbon black plants 
(furnace process), primary lead smelters, fuel conversion plants, 
sintering plants, secondary metal production plants, chemical process 
plants, fossil fuel boilers (or combinations thereof) totaling more than 
250 million British thermal units per hour heat input, petroleum storage 
and transfer units with a total storage capacity exceeding 300,000 
barrels, taconite ore processing plants, glass fiber processing plants, 
and charcoal production plants;
    (b) Notwithstanding the stationary source size specified in 
paragraph (b)(1)(i) of this section, any stationary source which emits, 
or has the potential to emit, 250 tons per year or more of any air 
pollutant subject to regulation under the Act; or
    (c) Any physical change that would occur at a stationary source not 
otherwise qualifying under paragraph (b)(1) of this section, as a major 
stationary source, if the changes would constitute a major stationary 
source by itself.
    (ii) A major stationary source that is major for volatile organic 
compounds shall be considered major for ozone.
    (iii) The fugitive emissions of a stationary source shall not be 
included in determining for any of the purposes of this section whether 
it is a major stationary source, unless the source belongs to one of the 
following categories of stationary sources:
    (a) Coal cleaning plants (with thermal dryers);
    (b) Kraft pulp mills;
    (c) Portland cement plants;
    (d) Primary zinc smelters;
    (e) Iron and steel mills;
    (f) Primary aluminum ore reduction plants;
    (g) Primary copper smelters;
    (h) Municipal incinerators capable of charging more than 250 tons of 
refuse per day;
    (i) Hydrofluoric, sulfuric, or nitric acid plants;
    (j) Petroleum refineries;
    (k) Lime plants;
    (l) Phosphate rock processing plants;
    (m) Coke oven batteries;
    (n) Sulfur recovery plants;
    (o) Carbon black plants (furnace process);
    (p) Primary lead smelters;
    (q) Fuel conversion plants;
    (r) Sintering plants;
    (s) Secondary metal production plants;
    (t) Chemical process plants;
    (u) Fossil-fuel boilers (or combination thereof) totaling more than 
250 million British thermal units per hour heat input;
    (v) Petroleum storage and transfer units with a total storage 
capacity exceeding 300,000 barrels;
    (w) Taconite ore processing plants;
    (x) Glass fiber processing plants;
    (y) Charcoal production plants;
    (z) Fossil fuel-fired steam electric plants of more that 250 million 
British thermal units per hour heat input, and
    (aa) Any other stationary source category which, as of August 7, 
1980, is being regulated under section 111 or 112 of the Act.
    (2)(i) Major modification means any physical change in or change in 
the method of operation of a major stationary source that would result 
in a significant net emissions increase of any pollutant subject to 
regulation under the Act.
    (ii) Any net emissions increase that is significant for volatile 
organic compounds shall be considered significant for ozone.
    (iii) A physical change or change in the method of operation shall 
not include:
    (a) Routine maintenance, repair and replacement;
    (b) Use of an alternative fuel or raw material by reason of an order 
under sections 2 (a) and (b) of the Energy Supply and Environmental 
Coordination Act of 1974 (or any superseding legislation) or by reason 
of a natural gas curtailment plant pursuant to the Federal Power Act;
    (c) Use of an alternative fuel by reason of an order or rule under 
section 125 of the Act;
    (d) Use of an alternative fuel at a steam generating unit to the 
extent that the fuel is generated from municipal solid waste;
    (e) Use of an alternative fuel or raw material by a stationary 
source which:
    (1) The source was capable of accommodating before January 6, 1975, 
unless such change would be prohibited under

[[Page 15]]

any federally enforceable permit condition which was established after 
January 6, 1975 pursuant to 40 CFR 52.21 or under regulations approved 
pursuant to 40 CFR subpart I or 40 CFR 51.166; or
    (2) The source is approved to use under any permit issued under 40 
CFR 52.21 or under regulations approved pursuant to 40 CFR 51.166;
    (f) An increase in the hours of operation or in the production rate, 
unless such change would be prohibited under any federally enforceable 
permit condition which was established after January 6, 1975, pursuant 
to 40 CFR 52.21 or under regulations approved pursuant to 40 CFR subpart 
I or 40 CFR 51.166.
    (g) Any change in ownership at a stationary source.
    (h) The addition, replacement or use of a pollution control project 
at an existing electric utility steam generating unit, unless the 
Administrator determines that such addition, replacement, or use renders 
the unit less environmentally beneficial, or except:
    (1) When the Administrator has reason to believe that the pollution 
control project would result in a significant net increase in 
representative actual annual emissions of any criteria pollutant over 
levels used for that source in the most recent air quality impact 
analysis in the area conducted for the purpose of title I, if any, and
    (2) The Administrator determines that the increase will cause or 
contribute to a violation of any national ambient air quality standard 
or PSD increment, or visibility limitation.
    (i) The installation, operation, cessation, or removal of a 
temporary clean coal technology demonstration project, provided that the 
project complies with:
    (1) The State implementation plan for the State in which the project 
is located, and
    (2) Other requirements necessary to attain and maintain the national 
ambient air quality standards during the project and after it is 
terminated.
    (j) The installation or operation of a permanent clean coal 
technology demonstration project that constitutes repowering, provided 
that the project does not result in an increase in the potential to emit 
of any regulated pollutant emitted by the unit. This exemption shall 
apply on a pollutant-by-pollutant basis.
    (k) The reactivation of a very clean coal-fired electric utility 
steam generating unit.
    (3)(i) Net emissions increase means the amount by which the sum of 
the following exceeds zero:
    (a) Any increase in actual emissions from a particular physical 
change or change in method of operation at a stationary source; and
    (b) Any other increases and decreases in actual emissions at the 
source that are contemporaneous with the particular change and are 
otherwise creditable.
    (ii) An increase or decrease in actual emissions is contemporaneous 
with the increase from the particular change only if it occurs between:
    (a) The date five years before construction on the particular change 
commences; and
    (b) The date that the increase from the particular change occurs.
    (iii) An increase or decrease in actual emissions is creditable only 
if the Administrator has not relied on it in issuing a permit for the 
source under this section, which permit is in effect when the increase 
in actual emissions from the particular change occurs.
    (iv) An increase or decrease in actual emissions of sulfur dioxide, 
particulate matter, or nitrogen oxide, which occurs before the 
applicable minor source baseline date is creditable only if it is 
required to be considered in calculating the amount of maximum allowable 
increases remaining available. With respect to particulate matter, only 
PM-10 emissions can be used to evaluate the net emissions increase for 
PM-10.
    (v) An increase in actual emissions is creditable only to the extent 
that the new level of actual emissions exceeds the old level.
    (vi) A decrease in actual emissions is creditable only to the extent 
that:
    (a) The old level of actual emissions or the old level of allowable 
emissions, whichever is lower, exceeds the new level of actual 
emissions;
    (b) It is federally enforceable at and after the time that actual 
construction on the particular change begins; and
    (c) It has approximately the same qualitative significance for 
public

[[Page 16]]

health and welfare as that attributed to the increase from the 
particular change.
    (vii) [Reserved]
    (viii) An increase that results from a physical change at a source 
occurs when the emissions unit on which construction occurred becomes 
operational and begins to emit a particular pollutant. Any replacement 
unit that requires shakedown becomes operational only after a reasonable 
shakedown period, not to exceed 180 days.
    (4) Potential to emit means the maximum capacity of a stationary 
source to emit a pollutant under its physical and operational design. 
Any physical or operational limitation on the capacity of the source to 
emit a pollutant, including air pollution control equipment and 
restrictions on hours of operation or on the type or amount of material 
combusted, stored, or processed, shall be treated as part of its design 
if the limitation or the effect it would have on emissions is federally 
enforceable. Secondary emissions do not count in determining the 
potential to emit of a stationary source.
    (5) Stationary source means any building, structure, facility, or 
installation which emits or may emit any air pollutant subject to 
regulation under the Act.
    (6) Building, structure, facility, or installation means all of the 
pollutant-emitting activities which belong to the same industrial 
grouping, are located on one or more contiguous or adjacent properties, 
and are under the control of the same person (or persons under common 
control) except the activities of any vessel. Pollutant-emitting 
activities shall be considered as part of the same industrial grouping 
if they belong to the same ``Major Group'' (i.e., which have the same 
first two digit code) as described in the Standard Industrial 
Classification Manual, 1972, as amended by the 1977 Supplement (U. S. 
Government Printing Office stock numbers 4101-0066 and 003-005-00176-0, 
respectively).
    (7) Emissions unit means any part of a stationary source which emits 
or would have the potential to emit any pollutant subject to regulation 
under the Act.
    (8) Construction means any physical change or change in the method 
of operation (including fabrication, erection, installation, demolition, 
or modification of an emissions unit) which would result in a change in 
actual emissions.
    (9) Commence as applied to construction of a major stationary source 
or major modification means that the owner or operator has all necessary 
preconstruction approvals or permits and either has:
    (i) Begun, or caused to begin, a continuous program of actual on-
site construction of the source, to be completed within a reasonable 
time; or
    (ii) Entered into binding agreements or contractual obligations, 
which cannot be cancelled or modified without substantial loss to the 
owner or operator, to undertake a program of actual construction of the 
source to be completed within a reasonable time.
    (10) Necessary preconstruction approvals or permits means those 
permits or approvals required under Federal air quality control laws and 
regulations and those air quality control laws and regulations which are 
part of the applicable State Implementation Plan.
    (11) Begin actual construction means, in general, initiation of 
physical on-site construction activities on an emissions unit which are 
of a permanent nature. Such activities include, but are not limited to, 
installation of building supports and foundations, laying underground 
pipework and construction of permanent storage structures. With respect 
to a change in method of operations, this term refers to those on-site 
activites other than preparatory activities which mark the initiation of 
the change.
    (12) Best available control technology means an emissions limitation 
(including a visible emission standard) based on the maximum degree of 
reduction for each pollutant subject to regulation under Act which would 
be emitted from any proposed major stationary source or major 
modification which the Administrator, on a case-by-case basis, taking 
into account energy, environmental, and economic impacts and other 
costs, determines is achievable for such source or modification

[[Page 17]]

through application of production processes or available methods, 
systems, and techniques, including fuel cleaning or treatment or 
innovative fuel combustion techniques for control of such pollutant. In 
no event shall application of best available control technology result 
in emissions of any pollutant which would exceed the emissions allowed 
by any applicable standard under 40 CFR parts 60 and 61. If the 
Administrator determines that technological or economic limitations on 
the application of measurement methodology to a particular emissions 
unit would make the imposition of an emissions standard infeasible, a 
design, equipment, work practice, operational standard, or combination 
thereof, may be prescribed instead to satisfy the requirement for the 
application of best available control technology. Such standard shall, 
to the degree possible, set forth the emissions reduction achievable by 
implementation of such design, equipment, work practice or operation, 
and shall provide for compliance by means which achieve equivalent 
results.
    (13)(i) ``Baseline concentration'' means that ambient concentration 
level which exists in the baseline area at the time of the applicable 
minor source baseline date. A baseline concentration is determined for 
each pollutant for which a baseline date is established and shall 
include:
    (a) The actual emissions representative of sources in existence on 
the applicable minor source baseline date, except as provided in 
paragraph (b)(13)(ii) of this section;
    (b) The allowable emissions of major stationary sources which 
commenced construction before the major source baseline date but were 
not in operation by the applicable minor source baseline date.
    (ii) The following will not be included in the baseline 
concentration and will affect the applicable maximum allowable 
increase(s):
    (a) Actual emissions from any major stationary source on which 
construction commenced after the major source baseline date; and
    (b) Actual emissions increases and decreases at any stationary 
source occurring after the minor source baseline date.
    (14)(i) Major source baseline date means:
    (a) In the case of particulate matter and sulfur dioxide, January 6, 
1975, and
    (b) In the case of nitrogen dioxide, February 8, 1988.
    (ii) ``Minor source baseline date'' means the earliest date after 
the trigger date on which a major stationary source or a major 
modification subject to 40 CFR 52.21 or to regulations approved pursuant 
to 40 CFR 51.166 submits a complete application under the relevant 
regulations. The trigger date is:
    (a) In the case of particulate matter and sulfur dioxide, August 7, 
1977, and
    (b) In the case of nitrogen dioxide, February 8, 1988.
    (iii) The baseline date is established for each pollutant for which 
increments or other equivalent measures have been established if:
    (a) The area in which the proposed source or modification would 
construct is designated as attainment or unclassifiable under section 
107(d)(i) (D) or (E) of the Act for the pollutant on the date of its 
complete application under 40 CFR 52.21; and
    (b) In the case of a major stationary source, the pollutant would be 
emitted in significant amounts, or, in the case of a major modification, 
there would be a significant net emissions increase of the pollutant.
    (iv) Any minor source baseline date established originally for the 
TSP increments shall remain in effect and shall apply for purposes of 
determining the amount of available PM-10 increments, except that the 
Administrator shall rescind a minor source baseline date where it can be 
shown, to the satisfaction of the Administrator, that the emissions 
increase from the major stationary source, or net emissions increase 
from the major modification, responsible for triggering that date did 
not result in a significant amount of PM-10 emissions.
    (15)(i) Baseline area means any intrastate area (and every part 
thereof) designated as attainment or unclassifiable under section 
107(d)(1) (D) or (E) of the Act in which the major source or major 
modification establishing the minor source baseline date would construct 
or would have an air quality impact equal

[[Page 18]]

to or greater than 1 g/m\3\ (annual average) of the pollutant 
for which the minor source baseline date is established.
    (ii) Area redesignations under section 107(d)(1) (D) or (E) of the 
Act cannot intersect or be smaller than the area of impact of any major 
stationary source or major modification which:
    (a) Establishes a minor source baseline date; or
    (b) Is subject to 40 CFR 52.21 and would be constructed in the same 
state as the state proposing the redesignation.
    (iii) Any baseline area established originally for the TSP 
increments shall remain in effect and shall apply for purposes of 
determining the amount of available PM-10 increments, except that such 
baseline area shall not remain in effect if the Administrator rescinds 
the corresponding minor source baseline date in accordance with 
paragraph (b)(14)(iv) of this section.
    (16) Allowable emissions means the emissions rate of a stationary 
source calculated using the maximum rated capacity of the source (unless 
the source is subject to federally enforceable limits which restrict the 
operating rate, or hours of operation, or both) and the most stringent 
of the following:
    (i) The applicable standards as set forth in 40 CFR parts 60 and 61;
    (ii) The applicable State Implementation Plan emissions limitation, 
including those with a future compliance date; or
    (iii) The emissions rate specified as a federally enforceable permit 
condition, including those with a future compliance date.
    (17) Federally enforceable means all limitations and conditions 
which are enforceable by the Administrator, including those requirements 
developed pursuant to 40 CFR parts 60 and 61, requirements within any 
applicable State implementation plan, any permit requirements 
established pursuant to 40 CFR 52.21 or under regulations approved 
pursuant to 40 CFR part 51, subpart I, including operating permits 
issued under an EPA-approved program that is incorporated into the State 
implementation plan and expressly requires adherence to any permit 
issued under such program.
    (18) Secondary emissions means emissions which would occur as a 
result of the construction or operation of a major stationary source or 
major modification, but do not come from the major stationary source or 
major modification itself. Secondary emissions include emissions from 
any offsite support facility which would not be constructed or increase 
its emissions except as a result of the construction or operation of the 
major stationary source or major modification. Secondary emissions do 
not include any emissions which come directly from a mobile source, such 
as emissions from the tailpipe of a motor vehicle, from a train, or from 
a vessel.
    (i) Emissions from ships or trains coming to or from the new or 
modified stationary source; and
    (ii) Emissions from any offsite support facility which would not 
otherwise be constructed or increase its emissions as a result of the 
construction or operation of the major stationary source or major 
modification.
    (19) Innovative control technology means any system of air pollution 
control that has not been adequately demonstrated in practice, but would 
have a substantial likelihood of achieving greater continuous emissions 
reduction than any control system in current practice or of achieving at 
least comparable reductions at lower cost in terms of energy, economics, 
or nonair quality environmental impacts.
    (20) Fugitive emissions means those emissions which could not 
reasonably pass through a stack, chimney, vent, or other functionally 
equivalent opening.
    (21)(i) Actual emissions means the actual rate of emissions of a 
pollutant from an emissions unit, as determined in accordance with 
paragraphs (b)(21) (ii) through (iv) of this section.
    (ii) In general, actual emissions as of a particular date shall 
equal the average rate, in tons per year, at which the unit actually 
emitted the pollutant during a two-year period which precedes the 
particular date and which is representative of normal source operation. 
The Administrator shall allow the use of a different time period upon

[[Page 19]]

a determination that it is more representative of normal source 
operation. Actual emissions shall be calculated using the unit's actual 
operating hours, production rates, and types of materials processed, 
stored, or combusted during the selected time period.
    (iii) The Administrator may presume that source-specific allowable 
emissions for the unit are equivalent to the actual emissions of the 
unit.
    (iv) For any emissions unit (other than an electric utility steam 
generating unit specified in paragraph (b)(21)(v) of this section) which 
has not begun normal operations on the particular date, actual emissions 
shall equal the potential to emit of the unit on that date.
    (v) For an electric utility steam generating unit (other than a new 
unit or the replacement of an existing unit) actual emissions of the 
unit following the physical or operational change shall equal the 
representative actual annual emissions of the unit, provided the source 
owner or operator maintains and submits to the Administrator on an 
annual basis for a period of 5 years from the date the unit resumes 
regular operation, information demonstrating that the physical or 
operational change did not result in an emissions increase. A longer 
period, not to exceed 10 years, may be required by the Administrator if 
he determines such a period to be more representative of normal source 
post-change operations.
    (22) Complete means, in reference to an application for a permit, 
that the application contains all of the information necessary for 
processing the application.
    (23) (i) Significant means, in reference to a net emissions increase 
or the potential of a source to emit any of the following pollutants, a 
rate of emissions that would equal or exceed any of the following rates:

                      Pollutant and Emissions Rate

Carbon monoxide: 100 tons per year (tpy)
Nitrogen oxides: 40 tpy
Sulfur dioxide: 40 tpy
Particulate matter:
    25 tpy of particulate matter emissions;
    15 tpy of PM10 emissions
Ozone: 40 tpy of volatile organic compounds
Lead: 0.6 tpy
Asbestos: 0.007 tpy
Beryllium: 0.0004 tpy
Mercury: 0.1 tpy
Vinyl chloride: 1 tpy
Fluorides: 3 tpy
Sulfuric acid mist: 7 tpy
Hydrogen sulfide (H2 S): 10 tpy
Total reduced sulfur (including H2 S): 10 tpy
Reduced sulfur compounds (including H2 S): 10 tpy
Municipal waste combustor organics (measured as total tetra- through 
octa-chlorinated dibenzo-p-dioxins and dibenzofurans): 3.2  x  
10-6 megagrams per year (3.5  x  10-6 tons per 
year). Municipal waste combustor metals (measured as particulate 
matter): 14 megagrams per year (15 tons per year)
Municipal waste combustor acid gases (measured as sulfur dioxide and 
hydrogen chloride): 36 megagrams per year (40 tons per year)
Municipal solid waste landfills emissions (measured as nonmethane 
organic compounds): 45 megagrams per year (50 tons per year)

    (ii) Significant means, in reference to a net emissions increase or 
the potential of a source to emit a pollutant subject to regulation 
under the Act that paragraph (b)(23)(i) of this section, does not list, 
any emissions rate.
    (iii) Notwithstanding paragraph (b)(23)(i) of this section, 
significant means any emissions rate or any net emissions increase 
associated with a major stationary source or major modification, which 
would construct within 10 kilometers of a Class I area, and have an 
impact on such area equal to or greater than 1 g/m3, 
(24-hour average).
    (24) Federal Land Manager means, with respect to any lands in the 
United States, the Secretary of the department with authority over such 
lands.
    (25) High terrain means any area having an elevation 900 feet or 
more above the base of the stack of a source.
    (26) Low terrain means any area other than high terrain.
    (27) Indian Reservation means any federally recognized reservation 
established by Treaty, Agreement, executive order, or act of Congress.
    (28) Indian Governing Body means the governing body of any tribe, 
band, or group of Indians subject to the jurisdiction of the United 
States and recognized by the United States as possessing power of self 
government.
    (29) Adverse impact on visibility means visibility impairment which 
interferes

[[Page 20]]

with the management, protection, preservation or enjoyment of the 
visitor's visual experience of the Federal Class I area. This 
determination must be made on a case-by-case basis taking into account 
the geographic extent, intensity, duration, frequency and time of 
visibility impairment, and how these factors correlate with (1) times of 
visitor use of the Federal Class I area, and (2) the frequency and 
timing of natural conditions that reduce visibility.
    (30) Volatile organic compounds (VOC) is as defined in 
Sec. 51.100(s) of this chapter.
    (31) Electric utility steam generating unit means any steam electric 
generating unit that is constructed for the purpose of supplying more 
than one-third of its potential electric output capacity and more than 
25 MW electrical output to any utility power distribution system for 
sale. Any steam supplied to a steam distribution system for the purpose 
of providing steam to a steam-electric generator that would produce 
electrical energy for sale is also considered in determining the 
electrical energy output capacity of the affected facility.
    (32) Pollution control project means any activity or project 
undertaken at an existing electric utility steam generating unit for 
purposes of reducing emissions from such unit. Such activities or 
projects are limited to:
    (i) The installation of conventional or innovative pollution control 
technology, including but not limited to advanced flue gas 
desulfurization, sorbent injection for sulfur dioxide and nitrogen 
oxides controls and electrostatic precipitators;
    (ii) An activity or project to accommodate switching to a fuel which 
is less polluting than the fuel in use prior to the activity or project, 
including, but not limited to natural gas or coal re-burning, or the co-
firing of natural gas and other fuels for the purpose of controlling 
emissions;
    (iii) A permanent clean coal technology demonstration project 
conducted under title II, section 101(d) of the Further Continuing 
Appropriations Act of 1985 (sec. 5903(d) of title 42 of the United 
States Code), or subsequent appropriations, up to a total amount of 
$2,500,000,000 for commercial demonstration of clean coal technology, or 
similar projects funded through appropriations for the Environmental 
Protection Agency; or
    (iv) A permanent clean coal technology demonstration project that 
constitutes a repowering project.
    (33) Representative actual annual emissions means the average rate, 
in tons per year, at which the source is projected to emit a pollutant 
for the two-year period after a physical change or change in the method 
of operation of a unit, (or a different consecutive two-year period 
within 10 years after that change, where the Administrator determines 
that such period is more representative of normal source operations), 
considering the effect any such change will have on increasing or 
decreasing the hourly emissions rate and on projected capacity 
utilization. In projecting future emissions the Administrator shall:
    (i) Consider all relevant information, including but not limited to, 
historical operational data, the company's own representations, filings 
with the State or Federal regulatory authorities, and compliance plans 
under title IV of the Clean Air Act; and
    (ii) Exclude, in calculating any increase in emissions that results 
from the particular physical change or change in the method of operation 
at an electric utility steam generating unit, that portion of the unit's 
emissions following the change that could have been accommodated during 
the representative baseline period and is attributable to an increase in 
projected capacity utilization at the unit that is unrelated to the 
particular change, including any increased utilization due to the rate 
of electricity demand growth for the utility system as a whole.
    (34) Clean coal technology means any technology, including 
technologies applied at the precombustion, combustion, or post 
combustion stage, at a new or existing facility which will achieve 
significant reductions in air emissions of sulfur dioxide or oxides of 
nitrogen associated with the utilization of coal in the generation of 
electricity, or process steam which was not in widespread use as of 
November 15, 1990.

[[Page 21]]

    (35) Clean coal technology demonstration project means a project 
using funds appropriated under the heading ``Department of Energy-Clean 
Coal Technology'', up to a total amount of $2,500,000,000 for commercial 
demonstration of clean coal technology, or similar projects funded 
through appropriations for the Environmental Protection Agency. The 
Federal contribution for a qualifying project shall be at least 20 
percent of the total cost of the demonstration project.
    (36) Temporary clean coal technology demonstration project means a 
clean coal technology demonstration project that is operated for a 
period of 5 years or less, and which complies with the State 
implementation plans for the State in which the project is located and 
other requirements necessary to attain and maintain the national ambient 
air quality standards during the project and after it is terminated.
    (37) (i) Repowering means replacement of an existing coal-fired 
boiler with one of the following clean coal technologies: atmospheric or 
pressurized fluidized bed combustion, integrated gasification combined 
cycle, magnetohydrodynamics, direct and indirect coal-fired turbines, 
integrated gasification fuel cells, or as determined by the 
Administrator, in consultation with the Secretary of Energy, a 
derivative of one or more of these technologies, and any other 
technology capable of controlling multiple combustion emissions 
simultaneously with improved boiler or generation efficiency and with 
significantly greater waste reduction relative to the performance of 
technology in widespread commercial use as of November 15, 1990.
    (ii) Repowering shall also include any oil and/or gas-fired unit 
which has been awarded clean coal technology demonstration funding as of 
January 1, 1991, by the Department of Energy.
    (iii) The Administrator shall give expedited consideration to permit 
applications for any source that satisfies the requirements of this 
subsection and is granted an extension under section 409 of the Clean 
Air Act.
    (38) Reactivation of a very clean coal-fired electric utility steam 
generating unit means any physical change or change in the method of 
operation associated with the commencement of commercial operations by a 
coal-fired utility unit after a period of discontinued operation where 
the unit:
    (i) Has not been in operation for the two-year period prior to the 
enactment of the Clean Air Act Amendments of 1990, and the emissions 
from such unit continue to be carried in the permitting authority's 
emissions inventory at the time of enactment;
    (ii) Was equipped prior to shut-down with a continuous system of 
emissions control that achieves a removal efficiency for sulfur dioxide 
of no less than 85 percent and a removal efficiency for particulates of 
no less than 98 percent;
    (iii) Is equipped with low-NOx burners prior to the time 
of commencement of operations following reactivation; and
    (iv) Is otherwise in compliance with the requirements of the Clean 
Air Act.
    (c) Ambient air increments. In areas designated as Class I, II or 
III, increases in pollutant concentration over the baseline 
concentration shall be limited to the following:

------------------------------------------------------------------------
                                                               Maximum
                                                              allowable
                                                               increase
                         Pollutant                           (micrograms
                                                              per cubic
                                                                meter)
------------------------------------------------------------------------
                                 Class I
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
Particulate matter:
    PM-10, annual arithmetic mean..........................            4
    PM-10, 24-hr maximum...................................            8
Sulfur dioxide:
    Annual arithmetic mean.................................            2
    24-hr maximum..........................................            5
    3-hr maximum...........................................           25
Nitrogen dioxide:
    Annual arithmetic mean.................................          2.5
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
                                Class II
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
Particulate matter:
    PM-10, annual arithmetic mean..........................           17
    PM-10, 24-hr maximum...................................           30
Sulfur dioxide:
    Annual arithmetic mean.................................           20
    24-hr maximum..........................................           91
    3-hr maximum...........................................          512
Nitrogen dioxide:
    Annual arithmetic mean.................................           25
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
                                Class III
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
Particulate matter
    PM-10, annual arithmetic mean..........................           34
    PM-10, 24-hr maximum...................................           60
Sulfur dioxide:
    Annual arithmetic mean.................................           40
    24-hr maximum..........................................          182

[[Page 22]]

    3-hr maximum...........................................          700
Nitrogen dioxide:
    Annual arithmetic mean.................................           50
------------------------------------------------------------------------


For any period other than an annual period, the applicable maximum 
allowable increase may be exceeded during one such period per year at 
any one location.
    (d) Ambient air ceilings. No concentration of a pollutant shall 
exceed:
    (1) The concentration permitted under the national secondary ambient 
air quality standard, or
    (2) The concentration permitted under the national primary ambient 
air quality standard, whichever concentration is lowest for the 
pollutant for a period of exposure.
    (e) Restrictions on area classifications. (1) All of the following 
areas which were in existence on August 7, 1977, shall be Class I areas 
and may not be redesignated:
    (i) International parks,
    (ii) National wilderness areas which exceed 5,000 acres in size,
    (iii) National memorial parks which exceed 5,000 acres in size, and
    (iv) National parks which exceed 6,000 acres in size.
    (2) Areas which were redesignated as Class I under regulations 
promulgated before August 7, 1977, shall remain Class I, but may be 
redesignated as provided in this section.
    (3) Any other area, unless otherwise specified in the legislation 
creating such an area, is initially designated Class II, but may be 
redesignated as provided in this section.
    (4) The following areas may be redesignated only as Class I or II:
    (i) An area which as of August 7, 1977, exceeded 10,000 acres in 
size and was a national monument, a national primitive area, a national 
preserve, a national recreational area, a national wild and scenic 
river, a national wildlife refuge, a national lakeshore or seashore; and
    (ii) A national park or national wilderness area established after 
August 7, 1977, which exceeds 10,000 acres in size.
    (f) [Reserved]
    (g) Redesignation. (1) All areas (except as otherwise provided under 
paragraph (e) of this section) are designated Class II as of December 5, 
1974. Redesignation (except as otherwise precluded by paragraph (e) of 
this section) may be proposed by the respective States or Indian 
Governing Bodies, as provided below, subject to approval by the 
Administrator as a revision to the applicable State implementation plan.
    (2) The State may submit to the Administrator a proposal to 
redesignate areas of the State Class I or Class II provided that:
    (i) At least one public hearing has been held in accordance with 
procedures established in Sec. 51.102 of this chapter;
    (ii) Other States, Indian Governing Bodies, and Federal Land 
Managers whose lands may be affected by the proposed redesignation were 
notified at least 30 days prior to the public hearing;
    (iii) A discussion of the reasons for the proposed redesignation, 
including a satisfactory description and analysis of the health, 
environmental, economic, social and energy effects of the proposed 
redesignation, was prepared and made available for public inspection at 
least 30 days prior to the hearing and the notice announcing the hearing 
contained appropriate notification of the availability of such 
discussion;
    (iv) Prior to the issuance of notice respecting the redesignation of 
an area that includes any Federal lands, the State has provided written 
notice to the appropriate Federal Land Manager and afforded adequate 
opportunity (not in excess of 60 days) to confer with the State 
respecting the redesignation and to submit written comments and 
recommendations. In redesignating any area with respect to which any 
Federal Land Manager had submitted written comments and recommendations, 
the State shall have published a list of any inconsistency between such 
redesignation and such comments and recommendations (together with the 
reasons for making such redesignation against the recommendation of the 
Federal Land Manager); and
    (v) The State has proposed the redesignation after consultation with 
the elected leadership of local and other

[[Page 23]]

substate general purpose governments in the area covered by the proposed 
redesignation.
    (3) Any area other than an area to which paragraph (e) of this 
section refers may be redesignated as Class III if--
    (i) The redesignation would meet the requirements of paragraph 
(g)(2) of this section;
    (ii) The redesignation, except any established by an Indian 
Governing Body, has been specifically approved by the Governor of the 
State, after consultation with the appropriate committees of the 
legislature, if it is in session, or with the leadership of the 
legislature, if it is not in session (unless State law provides that the 
redesignation must be specifically approved by State legislation) and if 
general purpose units of local government representing a majority of the 
residents of the area to be redesignated enact legislation or pass 
resolutions concurring in the redesignation:
    (iii) The redesignation would not cause, or contribute to, a 
concentration of any air pollutant which would exceed any maximum 
allowable increase permitted under the classification of any other area 
or any national ambient air quality standard; and
    (iv) Any permit application for any major stationary source or major 
modification, subject to review under paragraph (l) of this section, 
which could receive a permit under this section only if the area in 
question were redesignated as Class III, and any material submitted as 
part of that application, were available insofar as was practicable for 
public inspection prior to any public hearing on redesignation of the 
area as Class III.
    (4) Lands within the exterior boundaries of Indian Reservations may 
be redesignated only by the appropriate Indian Governing Body. The 
appropriate Indian Governing Body may submit to the Administrator a 
proposal to redesignate areas Class I, Class II, or Class III: Provided, 
That:
    (i) The Indian Governing Body has followed procedures equivalent to 
those required of a State under paragraphs (g)(2), (g)(3)(iii), and 
(g)(3)(iv) of this section; and
    (ii) Such redesignation is proposed after consultation with the 
State(s) in which the Indian Reservation is located and which border the 
Indian Reservation.
    (5) The Administrator shall disapprove, within 90 days of 
submission, a proposed redesignation of any area only if he finds, after 
notice and opportunity for public hearing, that such redesignation does 
not meet the procedural requirements of this paragraph or is 
inconsistent with paragraph (e) of this section. If any such disapproval 
occurs, the classification of the area shall be that which was in effect 
prior to the redesignation which was disapproved.
    (6) If the Administrator disapproves any proposed redesignation, the 
State or Indian Governing Body, as appropriate, may resubmit the 
proposal after correcting the deficiencies noted by the Administrator.
    (h) Stack heights. (1) The degree of emission limitation required 
for control of any air pollutant under this section shall not be 
affected in any manner by--
    (i) So much of the stack height of any source as exceeds good 
engineering practice, or
    (ii) Any other dispersion technique.
    (2) Paragraph (h)(1) of this section shall not apply with respect to 
stack heights in existence before December 31, 1970, or to dispersion 
techniques implemented before then.
    (i) Review of major stationary sources and major modifications--
Source applicability and exemptions. (1) No stationary source or 
modification to which the requirements of paragraphs (j) through (r) of 
this section apply shall begin actual construction without a permit 
which states that the stationary source or modification would meet those 
requirements. The Administrator has authority to issue any such permit.
    (2) The requirements of paragraphs (j) through (r) of this section 
shall apply to any major stationary source and any major modification 
with respect to each pollutant subject to regulation under the Act that 
it would emit, except as this section otherwise provides.
    (3) The requirements of paragraphs (j) through (r) of this section 
apply

[[Page 24]]

only to any major stationary source or major modification that would be 
constructed in an area designated as attainment or unclassifiable under 
section 107(d)(1)(D) or (E) of the Act.
    (4) The requirements of paragraphs (j) through (r) of this section 
shall not apply to a particular major stationary source or major 
modification, if;
    (i) Construction commenced on the source or modification before 
August 7, 1977. The regulations at 40 CFR 52.21 as in effect before 
August 7, 1977, shall govern the review and permitting of any such 
source or modification; or
    (ii) The source or modification was subject to the review 
requirements of 40 CFR 52.21(d)(1) as in effect before March 1, 1978, 
and the owner or operator:
    (a) Obtained under 40 CFR 52.21 a final approval effective before 
March 1, 1978;
    (b) Commenced construction before March 19, 1979; and
    (c) Did not discontinue construction for a period of 18 months or 
more and completed construction within a reasonable time; or
    (iii) The source or modification was subject to 40 CFR 52.21 as in 
effect before March 1, 1978, and the review of an application for 
approval for the stationary source or modification under 40 CFR 52.21 
would have been completed by March 1, 1978, but for an extension of the 
public comment period pursuant to a request for such an extension. In 
such a case, the application shall continue to be processed, and granted 
or denied, under 40 CFR 52.21 as in effect prior to March 1, 1978; or
    (iv) The source or modification was not subject to 40 CFR 52.21 as 
in effect before March 1, 1978, and the owner or operator:
    (a) Obtained all final Federal, state and local preconstruction 
approvals or permits necessary under the applicable State Implementation 
Plan before March 1, 1978;
    (b) Commenced construction before March 19, 1979; and
    (c) Did not discontinue construction for a period of 18 months or 
more and completed construction within a reasonable time; or
    (v) The source or modification was not subject to 40 CFR 52.21 as in 
effect on June 19, 1978 or under the partial stay of regulations 
published on February 5, 1980 (45 FR 7800), and the owner or operator:
    (a) Obtained all final Federal, state and local preconstruction 
approvals or permits necessary under the applicable State Implementation 
Plan before August 7, 1980;
    (b) Commenced construction within 18 months from August 7, 1980, or 
any earlier time required under the applicable State Implementation 
Plan; and
    (c) Did not discontinuue construction for a period of 18 months or 
more and completed construction within a reasonable time; or
    (vi) The source or modification would be a nonprofit health or 
nonprofit educational institution, or a major modification would occur 
at such an institution, and the governor of the state in which the 
source or modification would be located requests that it be exempt from 
those requirements; or
    (vii) The source or modification would be a major stationary source 
or major modification only if fugitive emissions, to the extent 
quantifiable, are considered in calculating the potential to emit of the 
stationary source or modification and the source does not belong to any 
of the following categories:
    (a) Coal cleaning plants (with thermal dryers);
    (b) Kraft pulp mills;
    (c) Portland cement plants;
    (d) Primary zinc smelters;
    (e) Iron and steel mills;
    (f) Primary aluminum ore reduction plants;
    (g) Primary copper smelters;
    (h) Municipal incinerators capable of charging more than 250 tons of 
refuse per day;
    (i) Hydrofluoric, sulfuric, or nitric acid plants;
    (j) Petroleum refineries;
    (k) Lime plants;
    (l) Phosphate rock processing plants;
    (m) Coke oven batteries;
    (n) Sulfur recovery plants;
    (o) Carbon black plants (furnace process);
    (p) Primary lead smelters;
    (q) Fuel conversion plants;
    (r) Sintering plants;

[[Page 25]]

    (s) Secondary metal production plants;
    (t) Chemical process plants;
    (u) Fossil-fuel boilers (or combination thereof) totaling more than 
250 million British thermal units per hour heat input;
    (v) Petroleum storage and transfer units with a total storage 
capacity exceeding 300,000 barrels;
    (w) Taconite ore processing plants;
    (x) Glass fiber processing plants;
    (y) Charcoal production plants;
    (z) Fossil fuel-fired steam electric plants of more than 250 million 
British thermal units per hour heat input;
    (aa) Any other stationary source category which, as of August 7, 
1980, is being regulated under section 111 or 112 of the Act; or
    (viii) The source is a portable stationary source which has 
previously received a permit under this section, and
    (a) The owner or operator proposes to relocate the source and 
emissions of the source at the new location would be temporary; and
    (b) The emissions from the source would not exceed its allowable 
emissions; and
    (c) The emissions from the source would impact no Class I area and 
no area where an applicable increment is known to be violated; and
    (d) Reasonable notice is given to the Administrator prior to the 
relocation identifying the proposed new location and the probable 
duration of operation at the new location. Such notice shall be given to 
the Administrator not less than 10 days in advance of the proposed 
relocation unless a different time duration is previously approved by 
the Administrator.
    (ix) The source or modification was not subject to Sec. 52.21, with 
respect to particulate matter, as in effect before July 31, 1987, and 
the owner or operator:
    (a) Obtained all final Federal, State, and local preconstruction 
approvals or permits necessary under the applicable State implementation 
plan before July 31, 1987;
    (b) Commenced construction within 18 months after July 31, 1987, or 
any earlier time required under the State implementation plan; and
    (c) Did not discontinue construction for a period of 18 months or 
more and completed construction within a reasonable period of time.
    (x) The source or modification was subject to 40 CFR 52.21, with 
respect to particulate matter, as in effect before July 31, 1987 and the 
owner or operator submitted an application for a permit under this 
section before that date, and the Administrator subsequently determines 
that the application as submitted was complete with respect to the 
particular matter requirements then in effect in the section. Instread, 
the requirments of paragraphs (j) through (r) of this section that were 
in effect before July 31, 1987 shall apply to such source or 
modifiction.
    (5) The requirements of paragraphs (j) through (r) of this section 
shall not apply to a major stationary source or major modification with 
respect to a particular pollutant if the owner or operator demonstrates 
that, as to that pollutant, the source or modification is located in an 
area designated as nonattainment under section 107 of the Act.
    (6) The requirements of paragraphs (k), (m) and (o) of this section 
shall not apply to a major stationary source or major modification with 
respect to a particular pollutant, if the allowable emissions of that 
pollutant from the source, or the net emissions increase of that 
pollutant from the modification:
    (i) Would impact no Class I area and no area where an applicable 
increment is known to be violated, and
    (ii) Would be temporary.
    (7) The requirements of paragraphs (k), (m) and (o) of this section 
as they relate to any maximum allowable increase for a Class II area 
shall not apply to a major modification at a stationary source that was 
in existence on March 1, 1978, if the net increase in allowable 
emissions of each pollutant subject to regulation under the Act from the 
modification after the application of best available control technology 
would be less than 50 tons per year.
    (8) The Administrator may exempt a stationary source or modification 
from the requirements of paragraph (m) of this section, with respect to 
monitoring for a particular pollutant if:

[[Page 26]]

    (i) The emissions increase of the pollutant from the new source or 
the net emissions increase of the pollutant from the modification would 
cause, in any area, air quality impacts less than the following amounts:

Carbon monoxide--575 g/m3, 8-hour average;
Nitrogen dioxide--14 g/m3, annual average;
Particulate matter--10 g/m3 of PM-10, 24-hour 
average;
Sulfur dioxide--13 g/m3, 24-hour average;
Ozone; 1
---------------------------------------------------------------------------


    1  No de minimis air quality level is provided for ozone. 
However, any net increase of 100 tons per year or more of volatile 
organic compounds subject to PSD would be required to perform an ambient 
impact analysis including the gathering of ambient air quality data.
---------------------------------------------------------------------------

    Lead--0.1 g/m3, 3-month average;
    Mercury--0.25 g/m3, 24-hour average;
    Beryllium--0.001 g/m3, 24-hour average;
    Fluorides--0.25 g/m3, 24-hour average;
    Vinyl chloride--15 g/m3, 24-hour average;
    Total reduced sulfur--10 g/m3, 1-hour average;
    Hydrogen sulfide--0.2 g/m3, 1-hour average;
    Reduced sulfur compounds--10 g/m3, 1-hour 
average; or

    (ii) The concentrations of the pollutant in the area that the source 
or modification would affect are less than the concentrations listed in 
paragraph (i)(8)(i) of this section, or the pollutant is not listed in 
paragraph (i)(8)(i) of this section.
    (9) The requirements for best available control technology in 
paragraph (j) of this section and the requirements for air quality 
analyses in paragraph (m)(1) of this section, shall not apply to a 
particular stationary source or modification that was subject to 40 CFR 
52.21 as in effect on June 19, 1978, if the owner or operator of the 
source or modification submitted an application for a permit under those 
regulations before August 7, 1980, and the Administrator subsequently 
determines that the application as submitted before that date was 
complete. Instead, the requirements at 40 CFR 52.21(j) and (n) as in 
effect on June 19, 1978 apply to any such source or modification.
    (10)(i) The requirements for air quality monitoring in paragraphs 
(m)(1) (ii) through (iv) of this section shall not apply to a particular 
source or modification that was subject to 40 CFR 52.21 as in effect on 
June 19, 1978, if the owner or operator of the source or modification 
submits an application for a permit under this section on or before June 
8, 1981, and the Administrator subsequently determines that the 
application as submitted before that date was complete with respect to 
the requirements of this section other than those in paragraphs (m)(1) 
(ii) through (iv) of this section, and with respect to the requirements 
for such analyses at 40 CFR 52.21(m)(2) as in effect on June 19, 1978. 
Instead, the latter requirements shall apply to any such source or 
modification.
    (ii) The requirements for air quality monitoring in paragraphs 
(m)(1) (ii) through (iv) of this section shall not apply to a particular 
source or modification that was not subject to 40 CFR 52.21 as in effect 
on June 19, 1978, if the owner or operator of the source or modification 
submits an application for a permit under this section on or before June 
8, 1981, and the Administrator subsequently determines that the 
application as submitted before that date was complete, except with 
respect to the requirements in paragraphs (m)(1) (ii) through (iv).
    (11)(i) At the discretion of the Administrator, the requirements for 
air quality monitoring of PM10 in paragraphs (m)(1) (i)--(iv) 
of this section may not apply to a particular source or modification 
when the owner or operator of the source or modification submits an 
application for a permit under this section on or before June 1, 1988 
and the Administrator subsequently determines that the application as 
submitted before that date was complete, except with respect to the 
requirements for monitoring particulate matter in paragraphs (m)(1) 
(i)--(iv).
    (ii) The requirements for air quiality monitoring pf PM10 
in paragraphs (m)(1), (ii) and (iv) and (m)(3) of this section shall 
apply to a particular source or modification if the owner or operator of 
the source or modification submits an application for a permit under 
this section after June 1, 1988 and no later than December 1, 1988. The 
data shall have been gathered over at least the period from February 1, 
1988 to the date the application becomes otherwise complete in 
accordance with

[[Page 27]]

the provisions set forth under paragraph (m)(1)(viii) of this section, 
except that if the Administrator determines that a complete and adequate 
analysis can be accomplished with monitoring data over a shorter period 
(not to be less than 4 months), the data that paragraph (m)(1)(iii) 
requires shall have been gathered over a shorter period.
    (12) The requirements of paragraph (k)(2) of this section shall not 
apply to a stationary source or modification with respect to any maximum 
allowable increase for nitrogen oxides if the owner or operator of the 
source or modification submitted an application for a permit under this 
section before the provisions embodying the maximum allowable increase 
took effect as part of the applicable implementation plan and the 
Administrator subsequently determined that the application as submitted 
before that date was complete.
    (13) The requirements in paragraph (k)(2) of this section shall not 
apply to a stationary source or modification with respect to any maximum 
allowable increase for PM-10 if (i) the owner or operator of the source 
or modification submitted an application for a permit under this section 
before the provisions embodying the maximum allowable increases for PM-
10 took effect in an implementation plan to which this section applies, 
and (ii) the Administrator subsequently determined that the application 
as submitted before that date was otherwise complete. Instead, the 
requirements in paragraph (k)(2) shall apply with respect to the maximum 
allowable increases for TSP as in effect on the date the application was 
submitted.
    (j) Control technology review. (1) A major stationary source or 
major modification shall meet each applicable emissions limitation under 
the State Implementation Plan and each applicable emissions standard and 
standard of performance under 40 CFR parts 60 and 61.
    (2) A new major stationary source shall apply best available control 
technology for each pollutant subject to regulation under the Act that 
it would have the potential to emit in significant amounts.
    (3) A major modification shall apply best available control 
technology for each pollutant subject to regulation under the Act for 
which it would result in a significant net emissions increase at the 
source. This requirement applies to each proposed emissions unit at 
which a net emissions increase in the pollutant would occur as a result 
of a physical change or change in the method of operation in the unit.
    (4) For phased construction projects, the determination of best 
available control technology shall be reviewed and modified as 
appropriate at the latest reasonable time which occurs no later than 18 
months prior to commencement of construction of each independent phase 
of the project. At such time, the owner or operator of the applicable 
stationary source may be required to demonstrate the adequacy of any 
previous determination of best available control technology for the 
source.
    (k) Source impact analysis. The owner or operator of the proposed 
source or modification shall demonstrate that allowable emission 
increases from the proposed source or modification, in conjunction with 
all other applicable emissions increases or reductions (including 
secondary emissions), would not cause or contribute to air pollution in 
violation of:
    (1) Any national ambient air quality standard in any air quality 
control region; or
    (2) Any applicable maximum allowable increase over the baseline 
concentration in any area.
    (l) Air quality models. (1) All estimates of ambient concentrations 
required under this paragraph shall be based on applicable air quality 
models, data bases, and other requirements specified in appendix W of 
part 51 of this chapter (Guideline on Air Quality Models).
    (2) Where an air quality model specified in appendix W of part 51 of 
this chapter (Guideline on Air Quality Models) is inappropriate, the 
model may be modified or another model substituted. Such a modification 
or substitution of a model may be made on a case-by-case basis or, where 
appropriate, on a generic basis for a specific state program. Written 
approval of the Administrator must be obtained for any modification

[[Page 28]]

or substitution. In addition, use of a modified or substituted model 
must be subject to notice and opportunity for public comment under 
procedures developed in accordance with paragraph (q) of this section.
    (m) Air quality analysis--(1) Preapplication analysis. (i) Any 
application for a permit under this section shall contain an analysis of 
ambient air quality in the area that the major stationary source or 
major modification would affect for each of the following pollutants:
    (a) For the source, each pollutant that it would have the potential 
to omit in a significant amount;
    (b) For the modification, each pollutant for which it would result 
in a significant net emissions increase.
    (ii) With respect to any such pollutant for which no National 
Ambient Air Quality Standard exists, the analysis shall contain such air 
quality monitoring data as the Administrator determines is necessary to 
assess ambient air quality for that pollutant in any area that the 
emissions of that pollutant would affect.
    (iii) With respect to any such pollutant (other than nonmethane 
hydrocarbons) for which such a standard does exist, the analysis shall 
contain continuous air quality monitoring data gathered for purposes of 
determining whether emissions of that pollutant would cause or 
contribute to a violation of the standard or any maximum allowable 
increase.
    (iv) In general, the continuous air quality monitoring data that is 
required shall have been gathered over a period of at least one year and 
shall represent at least the year preceding receipt of the application, 
except that, if the Administrator determines that a complete and 
adequate analysis can be accomplished with monitoring data gathered over 
a period shorter than one year (but not to be less than four months), 
the data that is required shall have been gathered over at least that 
shorter period.
    (v) For any application which becomes complete, except as to the 
requirements of paragraphs (m)(1) (iii) and (iv) of this section, 
between June 8, 1981, and February 9, 1982, the data that paragraph 
(m)(1)(iii) of this section, requires shall have been gathered over at 
least the period from February 9, 1981, to the date the application 
becomes otherwise complete, except that:
    (a) If the source or modification would have been major for that 
pollutant under 40 CFR 52.21 as in effect on June 19, 1978, any 
monitoring data shall have been gathered over at least the period 
required by those regulations.
    (b) If the Administrator determines that a complete and adequate 
analysis can be accomplished with monitoring data over a shorter period 
(not to be less than four months), the data that paragraph (m)(1)(iii) 
of this section, requires shall have been gathered over at least that 
shorter period.
    (c) If the monitoring data would relate exclusively to ozone and 
would not have been required under 40 CFR 52.21 as in effect on June 19, 
1978, the Administrator may waive the otherwise applicable requirements 
of this paragraph (v) to the extent that the applicant shows that the 
monitoring data would be unrepresentative of air quality over a full 
year.
    (vi) The owner or operator of a proposed stationary source or 
modification of violatile organic compounds who satisfies all conditions 
of 40 CFR part 51 Appendix S, section IV may provide post-approval 
monitoring data for ozone in lieu of providing preconstruction data as 
requried under paragraph (m)(1) of this section.
    (vii) For any application that becomes complete, except as to the 
requirements of paragraphs (m)(1) (iii) and (iv) pertaining to 
PM10, after December 1, 1988 and no later than August 1, 1989 
the data that paragraph (m)(1)(iii) requires shall have been gathered 
over at least the period from August 1, 1988 to the date the application 
becomes otherwise complete, except that if the Administrator determines 
that a complete and adequate analysis can be accomplished with 
monitoring data over a shorter period (not to be less than 4 months), 
the data that paragraph (m)(1)(iii) requires shall have been gathered 
over that shorter period.
    (viii) With respect to any requirements for air quality monitoring 
of PM10 under paragraphs (i)(11) (i) and

[[Page 29]]

(ii) of this section the owner or operator of the source or modification 
shall use a monitoring method approved by the Administratorand shall 
estimate the ambient concentrations of PM10 using the data 
collected by such approved monitoring method in accordance with 
estimating procedures approved by the Administrator.
    (2) Post-construction monitoring. The owner or operator of a major 
stationary source or major modification shall, after construction of the 
stationary source or modification, conduct such ambient monitoring as 
the Administrator determines is necessary to determine the effect 
emissions from the stationary source or modification may have, or are 
having, on air quality in any area.
    (3) Operations of monitoring stations. The owner or operator of a 
major stationary source or major modification shall meet the 
requirements of Appendix B to part 58 of this chapter during the 
operation of monitoring stations for purposes of satisfying paragraph 
(m) of this section.
    (n) Source information. The owner or operator of a proposed source 
or modification shall submit all information necessary to perform any 
analysis or make any determination required under this section.
    (1) With respect to a source or modification to which paragraphs 
(j), (l), (n) and (p) of this section apply, such information shall 
include:
    (i) A description of the nature, location, design capacity, and 
typical operating schedule of the source or modification, including 
specifications and drawings showing its design and plant layout;
    (ii) A detailed schedule for construction of the source or 
modification;
    (iii) A detailed description as to what system of continuous 
emission reduction is planned for the source or modification, emission 
estimates, and any other information necessary to determine that best 
available control technology would be applied.
    (2) Upon request of the Administrator, the owner or operator shall 
also provide information on:
    (i) The air quality impact of the source or modification, including 
meteorological and topographical data necessary to estimate such impact; 
and
    (ii) The air quality impacts, and the nature and extent of any or 
all general commercial, residential, industrial, and other growth which 
has occurred since August 7, 1977, in the area the source or 
modification would affect.
    (o) Additional impact analyses. (1) The owner or operator shall 
provide an analysis of the impairment to visibility, soils and 
vegetation that would occur as a result of the source or modification 
and general commercial, residential, industrial and other growth 
associated with the source or modification. The owner or operator need 
not provide an analysis of the impact on vegetation having no 
significant commercial or recreational value.
    (2) The owner or operator shall provide an analysis of the air 
quality impact projected for the area as a result of general commercial, 
residential, industrial and other growth associated with the source or 
modification.
    (3) Visibility monitoring. The Administrator may require monitoring 
of visibility in any Federal class I area near the proposed new 
stationary source for major modification for such purposes and by such 
means as the Administrator deems necessary and appropriate.
    (p) Sources impacting Federal Class I areas--additional 
requirements--(1) Notice to Federal land managers. The Administrator 
shall provide written notice of any permit application for a proposed 
major stationary source or major modification, the emissions from which 
may affect a Class I area, to the Federal land manager and the Federal 
official charged with direct responsibility for management of any lands 
within any such area. Such notification shall include a copy of all 
information relevant to the permit application and shall be given within 
30 days of receipt and at least 60 days prior to any public hearing on 
the application for a permit to construct. Such notification shall 
include an analysis of the proposed source's anticipated impacts on 
visibility in the Federal Class I area. The Administrator shall also 
provide the Federal land manager and such Federal officials with a copy 
of the preliminary

[[Page 30]]

determination required under paragraph (q) of this section, and shall 
make available to them any materials used in making that determination, 
promptly after the Administrator makes such determination. Finally, the 
Administrator shall also notify all affected Federal land managers 
within 30 days of receipt of any advance notification of any such permit 
application.
    (2) Federal Land Manager. The Federal Land Manager and the Federal 
official charged with direct responsibility for management of such lands 
have an affirmative responsibility to protect the air quality related 
values (including visibility) of such lands and to consider, in 
consultation with the Administrator, whether a proposed source or 
modification will have an adverse impact on such values.
    (3) Visibility analysis. The Administrator shall consider any 
analysis performed by the Federal land manager, provided within 30 days 
of the notification required by paragraph (p)(1) of this section, that 
shows that a proposed new major stationary source or major modification 
may have an adverse impact on visibility in any Federal Class I area. 
Where the Administrator finds that such an analysis does not demonstrate 
to the satisfaction of the Administrator that an adverse impact on 
visibility will result in the Federal Class I area, the Administrator 
must, in the notice of public hearing on the permit application, either 
explain his decision or give notice as to where the explanation can be 
obtained.
    (4) Denial--impact on air quality related values. The Federal Land 
Manager of any such lands may demonstrate to the Administrator that the 
emissions from a proposed source or modification would have an adverse 
impact on the air quality-related values (including visibility) of those 
lands, notwithstanding that the change in air quality resulting from 
emissions from such source or modification would not cause or contribute 
to concentrations which would exceed the maximum allowable increases for 
a Class I area. If the Administrator concurs with such demonstration, 
then he shall not issue the permit.
    (5) Class I variances. The owner or operator of a proposed source or 
modification may demonstrate to the Federal Land Manager that the 
emissions from such source or modification would have no adverse impact 
on the air quality related values of any such lands (including 
visibility), notwithstanding that the change in air quality resulting 
from emissions from such source or modification would cause or 
contribute to concentrations which would exceed the maximum allowable 
increases for a Class I area. If the Federal land manager concurs with 
such demonstration and he so certifies, the State may authorize the 
Administrator: Provided, That the applicable requirements of this 
section are otherwise met, to issue the permit with such emission 
limitations as may be necessary to assure that emissions of sulfur 
dioxide, particulate matter, and nitrogen oxides would not exceed the 
following maximum allowable increases over minor source baseline 
concentration for such pollutants:

------------------------------------------------------------------------
                                                               Maximum
                                                              allowable
                                                               increase
                         Pollutant                           (micrograms
                                                              per cubic
                                                                meter)
------------------------------------------------------------------------
Particulate matter:
    PM-10, annual arithmetic mean..........................           17
    PM-10, 24-hr maximum...................................           30
Sulfur dioxide:
    Annual arithmetic mean.................................           20
    24-hr maximum..........................................           91
    3-hr maximum...........................................          325
Nitrogen dioxide:
    Annual arithmetic mean.................................           25
------------------------------------------------------------------------

    (6) Sulfur dioxide variance by Governor with Federal Land Manager's 
concurrence. The owner or operator of a proposed source or modification 
which cannot be approved under paragraph (q)(4) of this section may 
demonstrate to the Governor that the source cannot be constructed by 
reason of any maximum allowable increase for sulfur dioxide for a period 
of twenty-four hours or less applicable to any Class I area and, in the 
case of Federal mandatory Class I areas, that a variance under this 
clause would not adversely affect the air quality related values of the 
area (including visibility). The Governor, after consideration of the 
Federal Land Manager's recommendation (if any) and subject to his 
concurrence, may, after notice and public hearing, grant a variance from 
such maximum

[[Page 31]]

allowable increase. If such variance is granted, the Administrator shall 
issue a permit to such source or modification pursuant to the 
requirements of paragraph (q)(7) of this section: Provided, That the 
applicable requirements of this section are otherwise met.
    (7) Variance by the Governor with the President's concurrence. In 
any case where the Governor recommends a variance in which the Federal 
Land Manager does not concur, the recommendations of the Governor and 
the Federal Land Manager shall be transmitted to the President. The 
President may approve the Governor's recommendation if he finds that the 
variance is in the national interest. If the variance is approved, the 
Administrator shall issue a permit pursuant to the requirements of 
paragraph (q)(7) of this section: Provided, That the applicable 
requirements of this section are otherwise met.
    (8) Emission limitations for Presidential or gubernatorial variance. 
In the case of a permit issued pursuant to paragraph (q) (5) or (6) of 
this section the source or modification shall comply with such emission 
limitations as may be necessary to assure that emissions of sulfur 
dioxide from the source or modification would not (during any day on 
which the otherwise applicable maximum allowable increases are exceeded) 
cause or contribute to concentrations which would exceed the following 
maximum allowable increases over the baseline concentration and to 
assure that such emissions would not cause or contribute to 
concentrations which exceed the otherwise applicable maximum allowable 
increases for periods of exposure of 24 hours or less for more than 18 
days, not necessarily consecutive, during any annual period:

                       Maximum Allowable Increase
                      [Micrograms per cubic meter]
------------------------------------------------------------------------
                                                         Terrain areas
                 Period of exposure                  -------------------
                                                         Low      High
------------------------------------------------------------------------
24-hr maximum.......................................        36        62
3-hr maximum........................................       130       221
------------------------------------------------------------------------

    (q) Public participation. The Administrator shall follow the 
applicable procedures of 40 CFR part 124 in processing applications 
under this section. The Administrator shall follow the procedures at 40 
CFR 52.21(r) as in effect on June 19, 1979, to the extent that the 
procedures of 40 CFR part 124 do not apply.
    (r) Source obligation. (1) Any owner or operator who constructs or 
operates a source or modification not in accordance with the application 
submitted pursuant to this section or with the terms of any approval to 
construct, or any owner or operator of a source or modification subject 
to this section who commences construction after the effective date of 
these regulations without applying for and receiving approval hereunder, 
shall be subject to appropriate enforcement action.
    (2) Approval to construct shall become invalid if construction is 
not commenced within 18 months after receipt of such approval, if 
construction is discontinued for a period of 18 months or more, or if 
construction is not completed within a reasonable time. The 
Administrator may extend the 18-month period upon a satisfactory showing 
that an extension is justified. This provision does not apply to the 
time period between construction of the approved phases of a phased 
construction project; each phase must commence construction within 18 
months of the projected and approved commencement date.
    (3) Approval to construct shall not relieve any owner or operator of 
the responsibility to comply fully with applicable provisions of the 
State implementation plan and any other requirements under local, State, 
or Federal law.
    (4) At such time that a particular source or modification becomes a 
major stationary source or major modification solely by virtue of a 
relaxation in any enforceable limitation which was established after 
August 7, 1980, on the capacity of the source or modification otherwise 
to emit a pollutant, such as a restriction on hours of operation, then 
the requirements or paragraphs (j) through (s) of this section shall 
apply to the source or modification as though construction had not yet 
commenced on the source or modification.

[[Page 32]]

    (s) Environmental impact statements. Whenever any proposed source or 
modification is subject to action by a Federal Agency which might 
necessitate preparation of an environmental impact statement pursuant to 
the National Environmental Policy Act (42 U.S.C. 4321), review by the 
Administrator conducted pursuant to this section shall be coordinated 
with the broad environmental reviews under that Act and under section 
309 of the Clean Air Act to the maximum extent feasible and reasonable.
    (t) Disputed permits or redesignations. If any State affected by the 
redesignation of an area by an Indian Governing Body, or any Indian 
Governing Body of a tribe affected by the redesignation of an area by a 
State, disagrees with such redesignation, or if a permit is proposed to 
be issued for any major stationary source or major modification proposed 
for construction in any State which the Governor of an affected State or 
Indian Governing Body of an affected tribe determines will cause or 
contribute to a cumulative change in air quality in excess of that 
allowed in this part within the affected State or Indian Reservation, 
the Governor or Indian Governing Body may request the Administrator to 
enter into negotiations with the parties involved to resolve such 
dispute. If requested by any State or Indian Governing Body involved, 
the Administrator shall make a recommendation to resolve the dispute and 
protect the air quality related values of the lands involved. If the 
parties involved do not reach agreement, the Administrator shall resolve 
the dispute and his determination, or the results of agreements reached 
through other means, shall become part of the applicable State 
implementation plan and shall be enforceable as part of such plan. In 
resolving such disputes relating to area redesignation, the 
Administrator shall consider the extent to which the lands involved are 
of sufficient size to allow effective air quality management or have air 
quality related values of such an area.
    (u) Delegation of authority. (1) The Administrator shall have the 
authority to delegate his responsibility for conducting source review 
pursuant to this section, in accordance with paragraphs (v) (2) and (3) 
of this section.
    (2) Where the Administrator delegates the responsibility for 
conducting source review under this section to any agency other than a 
Regional Office of the Environmental Protection Agency, the following 
provisions shall apply:
    (i) Where the delegate agency is not an air pollution control 
agency, it shall consult with the appropriate State and local air 
pollution control agency prior to making any determination under this 
section. Similarly, where the delegate agency does not have continuing 
responsibility for managing land use, it shall consult with the 
appropriate State and local agency primarily responsible for managing 
land use prior to making any determination under this section.
    (ii) The delegate agency shall send a copy of any public comment 
notice required under paragraph (r) of this section to the Administrator 
through the appropriate Regional Office.
    (3) The Administrator's authority for reviewing a source or 
modification located on an Indian Reservation shall not be redelegated 
other than to a Regional Office of the Environmental Protection Agency, 
except where the State has assumed jurisdiction over such land under 
other laws. Where the State has assumed such jurisdiction, the 
Administrator may delegate his authority to the States in accordance 
with paragraph (v)(2) of this section.
    (4) In the case of a source or modification which proposes to 
construct in a class III area, emissions from which would cause or 
contribute to air quality exceeding the maximum allowable increase 
applicable if the area were designated a class II area, and where no 
standard under section 111 of the act has been promulgated for such 
source category, the Administrator must approve the determination of 
best available control technology as set forth in the permit.
    (v) Innovative control technology. (1) An owner or operator of a 
proposed major stationary source or major modification may request the 
Administrator in writing no later than the close of the comment period 
under 40 CFR 124.10 to approve a system of innovative control 
technology.

[[Page 33]]

    (2) The Administrator shall, with the consent of the governor(s) of 
the affected state(s), determine that the source or modification may 
employ a system of innovative control technology, if: --
    (i) The proposed control system would not cause or contribute to an 
unreasonable risk to public health, welfare, or safety in its operation 
or function;
    (ii) The owner or operator agrees to achieve a level of continuous 
emissions reduction equivalent to that which would have been required 
under paragraph (j)(2) of this section, by a date specified by the 
Administrator. Such date shall not be later than 4 years from the time 
of startup or 7 years from permit issuance;
    (iii) The source or modification would meet the requirements of 
paragraphs (j) and (k) of this section, based on the emissions rate that 
the stationary source employing the system of innovative control 
technology would be required to meet on the date specified by the 
Administrator;
    (iv) The source or modification would not before the date specified 
by the Administrator:
    (a) Cause or contribute to a violation of an applicable national 
ambient air quality standard; or
    (b) Impact any area where an applicable increment is known to be 
violated; and
    (v) All other applicable requirements including those for public 
participation have been met.
    (vi) The provisions of paragraph (p) of this section (relating to 
Class I areas) have been satisfied with respect to all periods during 
the life of the source or modification.
    (3) The Administrator shall withdraw any approval to employ a system 
of innovative control technology made under this section, if:
    (i) The proposed system fails by the specified date to achieve the 
required continuous emissions reduction rate; or
    (ii) The proposed system fails before the specified date so as to 
contribute to an unreasonable risk to public health, welfare, or safety; 
or
    (iii) The Administrator decides at any time that the proposed system 
is unlikely to achieve the required level of control or to protect the 
public health, welfare, or safety.
    (4) If a source or modification fails to meet the required level of 
continuous emission reduction within the specified time period or the 
approval is withdrawn in accordance with paragraph (v)(3) of this 
section, the Administrator may allow the source or modification up to an 
additional 3 years to meet the requirement for the application of best 
available control technology through use of a demonstrated system of 
control.
    (w) Permit rescission. (1) Any permit issued under this section or a 
prior version of this section shall remain in effect, unless and until 
it expires under paragraph (s) of this section or is rescinded.
    (2) Any owner or operator of a stationary source or modification who 
holds a permit for the source or modification which was issued under 40 
CFR 52.21 as in effect on July 30, 1987, or any earlier version of this 
section, may request that the Administrator rescind the permit or a 
particular portion of the permit.
    (3) The Administrator shall grant an application for rescission if 
the application shows that this section would not apply to the source or 
modification.
    (4) If the Administrator rescinds a permit under this paragraph, the 
public shall be given adequate notice of the rescission. Publication of 
an announcement of rescission in a newspaper of general circulation in 
the affected region within 60 days of the rescission shall be considered 
adequate notice.
[43 FR 26403, June 19, 1978]

    Editorial Note: For Federal Register citations affecting Sec. 52.21, 
see the List of CFR Sections Affected in the Finding Aids section of 
this volume.



Sec. 52.23  Violation and enforcement.

    Failure to comply with any provisions of this part, or with any 
approved regulatory provision of a State implementation plan, or with 
any permit condition or permit denial issued pursuant to approved or 
promulgated regulations for the review of new or modified stationary or 
indirect sources, or

[[Page 34]]

with any permit limitation or condition contained within an operating 
permit issued under an EPA-approved program that is incorporated into 
the State implementation plan, shall render the person or governmental 
entity so failing to comply in violation of a requirement of an 
applicable implementation plan and subject to enforcement action under 
section 113 of the Clean Air Act. With regard to compliance schedules, a 
person or Governmental entity will be considered to have failed to 
comply with the requirements of this part if it fails to timely submit 
any required compliance schedule, if the compliance schedule when 
submitted does not contain each of the elements it is required to 
contain, or if the person or Governmental entity fails to comply with 
such schedule.
[39 FR 33512, Sept. 18, 1974, as amended at 54 FR 27285, June 28, 1989]



Sec. 52.24  Statutory restriction on new sources.

    (a) After June 30, 1979, no major stationary source shall be 
constructed or modified in any nonattainment area as designated in 40 
CFR part 81, subpart C (``nonattainment area'') to which any State 
implementation plan applies, if the emissions from suy will cause or 
contribute to concentrations of any pollutant for which a national 
ambient air quality standard is exceeded in such area, unless, as of the 
time of application for a permit for such construction, such plan meets 
the requirements of Part D, Title I, of the Clean Air Act, as amended 
(42 U.S.C. 7501 et seq.) (``Part D''). This section shall not apply to 
any nonattainment area once EPA has fully approved the State 
implementation plan for the area as meeting the requirements of Part D.
    (b) For any nonattainment area for which the SIP satisfies the 
requirements of Part D, permits to construct and operate new or modified 
major stationary sources may be issued only if the applicable SIP is 
being carried out for the nonattainment area in which the proposed 
source is to be constructed or modified in accordance with the 
requirements of Part D.
    (c) The Emission Offset Interpretative Ruling, 40 CFR part 51, 
Appendix S (``Offset Ruling''), rather than paragraphs (a) and (b), 
governs permits to construct and operate applied for before the deadline 
for having a revised SIP in effect that satisfies Part D. This deadline 
is July 1, 1979, for areas designated as nonattainment on March 3, 1978 
(42 FR 8962). The revised SIP, rather than paragraph (a) of this 
section, governs permits applied for during a period when the revised 
SIP is in compliance with Part D.
    (d) The restrictions in paragraphs (a) and (b) apply only to major 
stationary sources of emissions that cause or contribute to 
concentrations of the pollutant for which the nonattainment area was 
designated as nonattainment, and for which the SIP does not meet the 
requirements of Part D or is not being carried out in accordance with 
the requirements of Part D.
    (e) For any area designated as nonattainment for any national 
ambient air quality standard, the restrictions in paragraphs (a) and (b) 
of this section, shall apply to any major stationary source or major 
modification that would be major for the pollutant for which the area is 
designated nonattainment, if the stationary source or major modification 
would be constructed anywhere in the designated nonattainment areas. A 
major stationary source or major modification that is major for volatile 
organic compounds is also major for ozone.
    (f) The following definitions shall apply under this section.
    (1) Stationary source means any building, structure, facility, or 
installation which emits or may emit any air pollutant subject to 
regulation under the Act.
    (2) Building, structure, facility or installation means all of the 
pollutant-emitting activities which belong to the same industrial 
grouping, are located on one or more contiguous or adjacent properties, 
and are under the control of the same person (or persons under common 
control) except the activities of any vessel. Pollutant-emitting 
activities shall be considered as part of the same industrial grouping 
if they belong to the same ``Major Group'' (i.e., which have the same 
two-digit code) as described in the following document,

[[Page 35]]

Standard Industrial Classification Manual, 1972, as amended by the 1977 
Supplement (U.S. Government Printing Office stock numbers 4101-0066 and 
003-005-00176-0, respectively).
    (3) Potential to emit means the maximum capacity of a stationary 
source to emit a pollutant under its physical and operational design. 
Any physical or operational limitation on the capacity of the source to 
emit a pollutant, including air pollution control equipment and 
restrictions on hours of operation or on amount of material combusted, 
stored, or processed, shall be treated as part of its design only if the 
limitation or the effect it would have on emissions is federally 
enforceable. Secondary emissions do not count in determining the 
potential to emit of a stationary source.
    (4)(i) Major stationary source means:
    (a) Any stationary source of air pollutants which emits, or has the 
potential to emit, 100 tons per year or more of any pollutant subject to 
regulation under the Act; or
    (b) Any physical change that would occur at a stationary source not 
qualifying under paragraph (f)(5)(i)(a) of this section, as a major 
stationary source, if the change would constitute a major stationary 
source by itself.
    (ii) A major stationary source that is major for volatile organic 
compounds shall be considered major for ozone.
    (iii) The fugitive emissions of a stationary source shall not be 
included in determining for any of the purposes of this section whether 
it is a major stationary source, unless the source belongs to one of the 
following categories of stationary sources:
    (a) Coal cleaning plants (with thermal dryers);
    (b) Kraft pulp mills;
    (c) Portland cement plants;
    (d) Primary zinc smelters;
    (e) Iron and steel mills;
    (f) Primary aluminum ore reduction plants;
    (g) Primary copper smelters;
    (h) Municipal incinerators capable of charging more than 250 tons of 
refuse per day;
    (i) Hydrofluoric, sulfuric, or nitric acid plants;
    (j) Petroleum refineries;
    (k) Lime plants;
    (l) Phosphate rock processing plants;
    (m) Coke oven batteries;
    (n) Sulfur recovery plants;
    (o) Carbon black plants (furnace process);
    (p) Primary lead smelters;
    (q) Fuel conversion plants;
    (r) Sintering plants;
    (s) Secondary metal production plants;
    (t) Chemical process plants;
    (u) Fossil-fuel boilers (or combination thereof) totaling more than 
250 million British thermal units per hour heat input;
    (v) Petroleum storage and transfer units with a total storage 
capacity exceeding 300,000 barrels;
    (w) Taconite ore processing plants;
    (x) Glass fiber processing plants;
    (y) Charcoal production plants;
    (z) Fossil fuel-fired steam electric plants of more than 250 million 
British thermal units per hour heat input;
    (aa) Any other stationary source category which, as of August 7, 
1980, is being regulated under section 111 or 112 of the Act.
    (5)(i) Major modification means any physical change in or change in 
the method of operation of a major stationary source that would result 
in a significant net emissions increase of any pollutant subject to 
regulation under the Act.
    (ii) Any net emissions increase that is considered significant for 
volatile organic compounds shall be considered significant for ozone.
    (iii) A physical change or change in the method of operation shall 
not include:
    (a) Routine maintenance, repair, and replacement;
    (b) Use of an alternative fuel or raw material by reason of an order 
under sections 2 (a) and (b) of the Energy Supply and Environmental 
Coordination Act of 1974 (or any superseding legislation) or by reason 
of a natural gas curtailment plan pursuant to the Federal Power Act;
    (c) Use of an alternative fuel by reason of an order or rule under 
section 125 of the Act;
    (d) Use of an alternative fuel at a steam generating unit to the 
extent that the fuel is generated from municipal solid waste;

[[Page 36]]

    (e) Use of an alternative fuel or raw material by a stationary 
source which:
    (1) The source was capable of accommodating before July 1, 1979, 
unless such change would be prohibited under any federally enforceable 
permit condition which was established after July 1, 1979 pursuant to 40 
CFR 52.21 or under regulations approved pursuant to 40 CFR subpart I or 
40 CFR 51.166; or
    (2) The source is approved to use under any permit issued under 
regulations approved pursuant to 40 CFR subpart I;
    (f) An increase in the hours of operation or in the production rate, 
unless such change is prohibited under any federally enforceable permit 
condition which was established after July 1, 1979 pursuant to 40 CFR 
52.21 or under regulations approved pursuant to 40 CFR subpart I or 40 
CFR 51.166.
    (g) Any change in ownership at a stationary source.
    (h) The addition, replacement or use of a pollution control project 
at an existing electric utility steam generating unit, unless the 
Administrator determines that such addition, replacement, or use renders 
the unit less environmentally beneficial, or except:
    (1) When the Administrator has reason to believe that the pollution 
control project would reslt in a significant net increase in 
representative actual annual emissions of any criteria pollutant over 
levels used for that source in the most recent air quality impact 
analysis in the area conducted for the purpose of title I, if any, and
    (2) The Administrator determines that the increase will cause or 
contribute to a violation of any national ambient air quality standard 
or PSD increment, or visibility limitation.
    (i) The installation, operation, cessation, or removal of a 
temporary clean coal technology demonstration project, provided that the 
project complies with:
    (1) The State implementation plan for the State in which the project 
is located, and
    (2) Other requirements necessary to attain and maintain the national 
ambient air quality standards during the project and after it is 
terminated.
    (6)(i) Net emissions increase means the amount by which the sum of 
the following exceeds zero:
    (a) Any increase in actual emissions from a particular physical 
change or change in the method of operation at a stationary source; and
    (b) Any other increases and decreases in actual emissions at the 
source that are contemporaneous with the particular change and are 
otherwise creditable.
    (ii) An increase or decrease in actual emissions is contemporaneous 
with the increase from the particular change only if it occurs between:
    (a) The date five years before construction on the particular change 
commences and
    (b) The date that the increase from the particular change occurs.
    (iii) An increase or decrease in actual emissions is creditable only 
if the Administrator has not relied on it in issuing a permit for the 
source under regulations approved pursuant to 40 CFR subpart I which 
permit is in effect when the increase in actual emissions from the 
particular change occurs.
    (iv) An increase in actual emissions is creditabletime. only to the 
extent that the new level of actual emissions exceeds the old level.
    (v) A decrease in actual emissions is creditable only to the extent 
that:
    (a) The old level of actual emissions or the old level of allowable 
emissions, whichever is lower, exceeds the new level of actual 
emissions;
    (b) It is federally enforceable at and after the time that 
construction on the particular change begins; and
    (c) The Administrator or reviewing authority has not relied on it in 
issuing any permit under regulations approved pursuant to 40 CFR subpart 
I or the State has not relied on it in demonstrating attainment or 
reasonable further progress.
    (d) It has approximately the same qualitative significance for 
public health and welfare as that attributed to the increase from the 
particular change.
    (vi) An increase that results from a physical change at a source 
occurs when the emissions unit on which construction occurred becomes 
operational and begins to emit a particular

[[Page 37]]

pollutant. Any replacement unit that requires shakedown becomes 
operational only after a reasonable shakedown period, not to exceed 180 
days.
    (7) Emissions unit means any part of a stationary source which emits 
or would have the potential to emit any pollutant subject to regulation 
under the Act.
    (8) Secondary emissions means emissions which would occur as a 
result of the construction or operation of a major stationary source or 
major modification, but do not come from the major stationary source or 
major modification itself. For the purpose of this section, secondary 
emissions must be specific, well defined, quantifiable, and impact the 
same general area as the stationary source or modification which causes 
the secondary emissions. Secondary emissions include emissions from any 
offsite support facility which would otherwise not be constructed or 
increase its emissions except as a result of the construction or 
operation of the major stationary source or major modification. 
Secondary emissions do not include any emissions which come directly 
from a mobile source, such as emissions from the tailpipe of a motor 
vehicle, from a train, or from a vessel.
    (9) Fugitive emissions means those emissions which could not 
reasonably pass through a stack, chimney, vent, or other functionally 
equivalent opening.
    (10) Significant means, in reference to a net emissions increase or 
the potential of a source to emit any of the following pollutants, a 
rate of emissions that would equal or exceed any of the following rates:

                      Pollutant and Emissions Rate

Carbon monoxide: 100 tons per year (tpy)
Nitrogen oxides: 40 tpy
Sulfur dioxide: 40 tpy
Ozone: 40 tpy of volatile organic compounds
Lead: 0.6 tpy

    (11) Allowable emissions means the emissions rate of a stationary 
source calculated using the maximum rated capacity of the source (unless 
the source is subject to federally enforceable limits which restrict the 
operating rate, or hours of operation, or both) and the most stringent 
of the following:
    (i) The applicable standards set forth in 40 CFR parts 60 and 61;
    (ii) Any applicable State Implementation Plan emissions limitation, 
including those with a future compliance date; or
    (iii) The emissions rate specified as a federally enforceable permit 
condition, including those with a future compliance date.
    (12) Federally enforceable means all limitations and conditions 
which are enforceable by the Administrator, including those requirements 
developed pursuant to 40 CFR parts 60 and 61, requirements within any 
applicable State implementation plan, any permit requirements 
established pursuant to 40 CFR 52.21 or under regulations approved 
pursuant to 40 CFR part 51, subpart I, including operating permits 
issued under an EPA-approved program that is incorporated into the State 
implementation plan and expressly requires adherence to any permit 
issued under such program.
    (13)(i) Actual emissions means the actual rate of emissions of a 
pollutant from an emissions unit, as determined in accordance with 
paragraphs (f) (ii) through (iv) of this section.
    (ii) In general, actual emissions as of a particular date shall 
equal the average rate, in tons per year, at which the unit actually 
emitted the pollutant during a two-year period which precedes the 
particular date and which is representative of normal source operation. 
The Administrator shall allow the use of a different time period upon a 
determination that it is more representative of normal source operation. 
Actual emissions shall be calculated using the unit's actual operating 
hours, production rates, and types of materials processed, stored, or 
combusted during the selected time period.
    (iii) The Administrator may presume that source-specific allowable 
emissions for the unit are equivalent to the actual emissions of the 
unit.
    (iv) For any emissions unit (other than an electric utility steam 
generating unit specified in paragraph (f)(13)(v) of this section) which 
has not begun normal operations on the particular date, actual emissions 
shall equal the potential to emit of the unit on that date.

[[Page 38]]

    (v) For an electric utility steam generating unit (other than a new 
unit or the replacement of an existing unit) actual emissions of the 
unit following the physical or operational change shall equal the 
representative actual annual emissions of the unit, provided the source 
owner or operator maintains and submits to the Administrator, on an 
annual basis for a period of 5 years from the date the unit resumes 
regular operation, information demonstrating that the physical or 
operational change did not result in an emissions increase. A longer 
period, not to exceed 10 years, may be required by the Administrator if 
he determines such a period to be more representative of normal source 
post-change operations.
    (14) Construction means any physical change or change in the method 
of operation (including fabrication, erection, installation, demolition, 
or modification) of an emissions unit which would result in a change in 
actual emissions.
    (15) Commence as applied to construction of a major stationary 
source or major modification means that the owner or operator has all 
necessary preconstruction approvals or permits and either has:
    (i) Begun, or caused to begin, a continuous program of actual on-
site construction of the source, to be completed within a reasonable 
time; or
    (ii) Entered into binding agreements or contractual obligations, 
which cannot be cancelled or modified without substantial loss to the 
owner or operator, to undertake a program of actual construction of the 
source to be completed within a reasonable time.
    (16) Necessary preconstruction approvals or permits means those 
permits or approvals required under federal air quality control laws and 
regulations and those air quality control laws and regulations which are 
part of the applicable State Implementation Plan.
    (17) Begin actual construction means, in general, initiation of 
physical on-site construction activities on an emissions unit which are 
of a permanent nature. Such activities include, but are not limited to, 
installation of building supports and foundations, laying of underground 
pipework, and construction of permanent storage structures. With respect 
to a change in method of operations, this term refers to those on-site 
activities other than preparatory activities which mark the initiation 
of change.
    (18) Volatile organic compounds (VOC) is as defined in 
Sec. 51.100(s) of this chapter.
    (19) Electric utility steam generating unit means any steam electric 
generating unit that is constructed for the purpose of supplying more 
than one-third of its potential electric output capacity and more than 
25 MW electrical output to any utility power distribution system for 
sale. Any steam supplied to a steam distribution system for the purpose 
of providing steam to a steam-electric generator that would produce 
electrical energy for sale is also considered in determining the 
electrical energy output capacity of the affected facility.
    (20) Representative actual annual emissions means the average rate, 
in tons per year, at which the source is projected to emit a pollutant 
for the two-year period after a physical change or change in the method 
of operation of a unit, (or a different consecutive two-year period 
within 10 years after that change, where the Administrator determines 
that such period is more representative of normal source operations), 
considering the effect any such change will have on increasing or 
decreasing the hourly emissions rate and on projected capacity 
utilization. In projecting future emissions the Administrator shall:
    (i) Consider-all relevant information, including but not limited to, 
historical operational data, the company's own representations, filings 
with the State or Federal regulatory authorities, and compliance plans 
under title IV of the Clean Air Act; and
    (ii) Exclude, in calculating any increase in emissions that results 
from the particular physical change or change in the method of operation 
at an electric utility steam generating unit, that portion of the unit's 
emissions following the change that could have been accommodated during 
the representative baseline period and is attributable to an increase in 
projected capacity utilization at the unit that is

[[Page 39]]

unrelated to the particular change, including any increased utilization 
due to the rate of electricity demand growth for the utility system as a 
whole.
    (21) Temporary clean coal technology demonstration project means a 
clean coal technology demonstration project that is operated for a 
period of 5 years or less, and which complies with the State 
implementation plans for the State in which the project is located and 
other requirements necessary to attain and maintain the national ambient 
air quality standards during the project and after it is terminated.
    (22) Clean coal technology means any technology, including 
technologies applied at the precombustion, combustion, or post 
combustion stage, at a new or existing facility which will achieve 
significant reductions in air emissions of sulfur dioxide or oxides of 
nitrogen associated with the utilization of coal in the generation of 
electricity, or process steam which was not in widespread use as of 
November 15, 1990.
    (23) Clean coal technology demonstration project means a project 
using funds appropriated under the heading `Department of Energy-Clean 
Coal Technology', up to a total amount of $2,500,000,000 for commercial 
demonstration of clean coal technology, or similar projects funded 
through appropriations for the Environmental Protection Agency. The 
Federal contribution for a qualifying project shall be at least 20 
percent of the total cost of the demonstration project.
    (24) Pollution control project means any activity or project 
undertaken at an existing electric utility steam generating unit for 
purposes of reducing emissions from such unit. Such activities or 
projects are limited to:
    (i) The installation of conventional or innovative pollution control 
technology, including but not limited to advanced flue gas 
desulfurization, sorbent injection for sulfur dioxide and nitrogen 
oxides controls and electrostatic precipitators;
    (ii) An activity or project to accommodate switching to a fuel which 
is less polluting than the fuel in use prior to the activity or project 
including, but not limited to natural gas or coal re-burning, co-firing 
of natural gas and other fuels for the purpose of controlling emissions;
    (iii) A permanent clean coal technology demonstration project 
conducted under title II, section 101(d) of the Further Continuing 
Appropriations Act of 1985 (section 5903(d) of title 42 of the United 
States Code), or subsequent appropriations, up to a total amount of 
$2,500,000,000 for commercial demonstration of clean coal technology, or 
similar projects funded through appropriations for the Environmental 
Protection Agency; or
    (iv) A permanent clean coal technology demonstration project that 
constitutes a repowering project.
    (g) This section shall not apply to a major stationary source or 
major modification if the source or modification was not subject to 40 
CFR part 51 Appendix S, as in effect on January 16, 1979, and the owner 
or operator:
    (1) Obtained all final Federal, state, and local preconstruction 
approvals or permits necessary under the applicable State Implementation 
Plan before August 7, 1980;
    (2) Commenced construction within 18 months from August 7, 1980, or 
any earlier time required under the applicable State Implementation 
Plan; and
    (3) Did not discontinue construction for a period of 18 months or 
more and completed construction within a reasonable time.
    (h) This section shall not apply to a source or modification that 
would be a major stationary source or major modification only if 
fugitive emissions, to the extent quantifiable, are considered in 
calculating the potential to emit of the stationary source or 
modification and the source does not belong to any of the following 
categories:
    (1) Coal cleaning plants (with thermal dryers);
    (2) Kraft pulp mills;
    (3) Portland cement plants;
    (4) Primary zinc smelters;
    (5) Iron and steel mills;
    (6) Primary aluminum ore reduction plants;
    (7) Primary copper smelters;
    (8) Municipal incinerators capable of charging more than 250 tons of 
refuse per day;

[[Page 40]]

    (9) Hydrofluoric, sulfuric, or nitric acid plants;
    (10) Petroleum refineries;
    (11) Lime plants;
    (12) Phosphate rock processing plants;
    (13) Coke oven batteries;
    (14) Sulfur recovery plants;
    (15) Carbon black plants (furnace process);
    (16) Primary lead smelters;
    (17) Fuel conversion plants;
    (18) Sintering plants;
    (19) Secondary metal production plants;
    (20) Chemical process plants;
    (21) Fossil-fuel boilers (or combination thereof) totaling more than 
250 million British thermal units per hour heat input;
    (22) Petroleum storage and transfer units with a total storage 
capacity exceeding 300,000 barrels;
    (23) Taconite ore processing plants;
    (24) Glass fiber processing plants;
    (25) Charcoal production plants;
    (26) Fossil fuel-fired steam electric plants of more than 250 
million British thermal units per hour heat input;
    (27) Any other stationary source category which, as of August 7, 
1980, is being regulated under section 111 or 112 of the Act.
    (i) At such time that a particular source or modification becomes a 
major stationary source or major modification solely by virtue of a 
relaxation in any enforceable limitation which was established after 
August 7, 1980, on the capacity of the source or modification otherwise 
to emit a pollutant, such as a restriction on hours of operation, then:
    (1) If the construction moratorium imposed pursuant to this section 
is still in effect for the nonattainment area in which the source or 
modification is located, then the permit may not be so revised; or
    (2) If the construction moratorium is no longer in effect in that 
area, then the requirements of 40 CFR 51.165(a) shall apply to the 
source or modification as though construction had not yet commenced on 
the source or modification.
    (j) This section does not apply to major stationary sources or major 
modifications locating in a clearly defined part of a nonattainment area 
(such as a political subdivision of a State), where EPA finds that a 
plan which meets the requirements of Part D is in effect and is being 
implemented in that part.
    (k) For an area designated as nonattainment after July 1, 1979, the 
restrictions in paragraphs (a) and (b) of this section shall not apply 
prior to eighteen months after the date the area is designated as 
nonattainment. The Offset Ruling shall govern permits to construct and 
operate applied for during the period between the date of designation as 
nonattainment and either the date the Part D plan is approved or the 
date the restrictions in paragraphs (a) and (b) of this section apply, 
whichever is earlier.
[44 FR 38473, July 2, 1979]

    Editorial Note: For Federal Register citations affecting Sec. 52.24, 
see the List of CFR Sections Affected in the Finding Aids section of 
this volume.



Sec. 52.26  Visibility monitoring strategy.

    (a) Plan Disapprovals. The provisions of this section are applicable 
to any State implementation plan which has been disapproved with respect 
to visibility monitoring. Specific disapprovals are listed where 
applicable in Subparts B through DD of this part. The provisions of this 
section have been incorporated by reference into the applicable 
implementation plan for various States, as provided in Subparts B 
through DDD of this part.
    (b) Definitions. For the purposes of this section:
    (1) Visibility protection area means any area listed in 40 CFR 
81.401-81.436 (1984).
    (2) All other terms shall have the meaning ascribed to them in the 
Clean Air Act, or in the protection of visibility program (40 CFR 
51.301), all as in effect on July 12, 1985.
    (c) Monitoring Requirements. (1) The Administrator, in cooperation 
with the appropriate Federal land manager, shall monitor visibility 
within each visibility protection area in any State whose State 
implementation plan is subject to a disapproval for failure to satisfy 
40 CFR 51.305 (1984).
    (2) The Administrator, in monitoring visibility within each such 
area, shall determine both background visibility

[[Page 41]]

conditions and reasonably attributable visibility impairment caused by a 
source or small group of sources for that area. The extent and the form 
of monitoring shall be sufficient for use in determining the potential 
effects of a new stationary source on visibility in the area, the 
stationary source or sources that are causing any visibility impairment, 
and progress toward remedying that impairment.
    (3) The Administrator shall use the following as appropriate to 
monitor visibility within each such area: (i) photographic cameras, (ii) 
fine particulate matter samplers, (iii) teleradiometers, (iv) 
nephelometers, (v) human observation, or (vi) other appropriate 
technology.
    (4) The Administrator, in cooperation with the Federal land 
managers, shall prepare monitoring plans that describe, to the maximum 
extent practicable, the methods and instruments of data collection, the 
monitoring locations and frequencies, the implementation schedule, the 
quality assurance procedures, and the methods of data reporting that the 
Administrator will use for each area. The Administrator shall make these 
plans available to the public.
    (5) The Administrator shall establish a central repository of 
monitoring data that includes any data on background visibility 
conditions and reasonably attributable impairment that the Administrator 
collects under this section and that the Federal land manager may 
collect or may have collected independently. These data shall be 
available to any person, subject to reasonable charges for copying.
    (d) Monitoring Plan Revision. (1) The Administrator shall review the 
monitoring plan annually for each visibility protection area, revise it 
as necessary, and include an assessment of changes to visibility 
conditions since the last review. The Administrator shall make all plan 
revisions available to the public.
    (2) Any person may make a request to the Administrator, at any time, 
for a revision to a monitoring plan. The Administrator shall respond to 
any such request within one year.
    (e) Delegation. The Administrator may delegate, with respect to a 
particular visibility protection area, any of his functions under this 
section to any State or local air pollution control agency of any State 
whose boundaries encompass that area or to any Federal land manager with 
jurisdiction over the area.
[50 FR 28550, July 12, 1985]



Sec. 52.27  Protection of visibility from sources in attainment areas.

    (a) Plan disapproval. The provisions of this section are applicable 
to any State implementation plan which has been disapproved with respect 
to protection of visibility, in mandatory Class I Federal areas, from 
sources emitting pollutants in any portion of any State where the 
existing air quality is better than the national ambient air quality 
standards for such pollutants, and where a State PSD program has been 
approved as part of the applicable SIP pursuant to 40 CFR 51.24. 
Specific disapprovals are listed where applicable in Subparts B through 
DDD of this part. The provisions of this section have been incorporated 
by reference into the applicable implementation plans for various 
States, as provided in Subparts B through DDD of this part.
    (b) Definitions. For purposes of this section, all terms shall have 
the meaning ascribed to them in the Clean Air Act, in the prevention of 
significant deterioration (PSD) program approved as part of the 
applicable SIP pursuant to 40 CFR 51.24 for the State, or in the 
protection of visibility program (40 CFR 51.301), all as in effect on 
July 12, 1985.
    (c) Federal visibility analysis. Any person shall have the right, in 
connection with any application for a permit to construct a major 
stationary source or major modification, to request that the 
administrator take responsibility from the State for conducting the 
required review of a proposed source's impact on visibility in any 
Fedral Class I area. If requested, the Administrator shall take such 
responsibility and conduct such review pursuant to paragraphs (e), (f) 
and (g) of this section in any case where the State fails to provide all 
of the procedural steps listed in paragraph (d) of this section. A 
request pursuant to this paragraph must be made within 60 days of the 
notice soliciting

[[Page 42]]

public comment on a permit, unless such notice is not properly given. 
The Administrator will not entertain requests challenging the substance 
of any State action concerning visibility where the State has provided 
all of the procedural steps listed in paragraph (d) of this section.
    (d) Procedural steps in visibility review. (1) The reviewing 
authority must provide written notification to all affected Federal land 
managers of any permit application for any proposed new major stationary 
source or major modification that may affect visibility in any Federal 
Class I area. Such notification shall include a copy of all information 
relevant to the permit application and shall be given within 30 days of 
receipt and at least 60 days prior to any public hearing on the 
application for a permit to construct. Such notification shall include 
the proposed source's anticipated impacts on visibility in any Federal 
Class I area as provided by the applicant. Notification must also be 
given to all affected Federal land managers within 30 days of receipt of 
any advance notification of any such permit application.
    (2) The reviewing authority must consider any analysis performed by 
the Federal land managers, provided within 30 days of the notification 
required by paragraph (d)(1) of this section, that shows that such 
proposed new major stationary source or major modification may have:
    (i) An adverse impact on visibility in any Federal Class I area, or
    (ii) An adverse impact on visibility in an integral vista codified 
in part 81 of this title.
    (3) Where the reviewing authority finds that such an analysis does 
not demonstrate that the effect in paragraphs (d)(2) (i) or (ii) of this 
section will occur, either an explanation of its decision or 
notification as to where the explanation can be obtained must be 
included in the notice of public hearing.
    (4) Where the reviewing authority finds that such an analysis does 
demonstrate that the effect in paragraph (d)(2)(i) of this section will 
occur, the permit shall not be issued.
    (5) Where the reviewing authority finds that such an analysis does 
demonstrate that the effect in paragraph (d)(2)(ii) of this section will 
occur, the reviewing authority may issue a permit if the emissions from 
the source or modification will be consistent with reasonable progress 
toward the national goal. In making this decision, the reviewing 
authority may take into account the costs of compliance, the time 
necessary for compliance, the energy and nonair quality environmental 
impacts of compliance, and the useful life of the source.
    (e) Federal land manager notification. The Administrator shall 
provide all of the procedural steps listed in paragraph (d) of this 
section in conducting reviews pursuant to this section.
    (f) Monitoring. The Administrator may require monitoring of 
visibility in any Federal Class I area near the proposed new stationary 
source or major modification for such purposes and by such means as the 
Administrator deems necessary and appropriate.
    (g) Public participation. The Administrator shall follow the 
applicable procedures at 40 CFR part 124 in conducting reviews under 
this section. The Administrator shall follow the procedures at 40 CFR 
52.21(q) as in effect on August 7, 1980, to the extent that the 
procedures of 40 CFR part 124 do not apply.
    (h) Federal permit. In any case where the Administrator has made a 
finding that a State consistently fails or is unable to provide the 
procedural steps listed in paragraph (d) of this section, the 
Administrator shall require all prospective permit applicants in such 
State to apply directly to the Administrator, and the Administrator 
shall conduct a visibility review pursuant to this section for all 
permit applications.
[50 FR 28551, July 12, 1985, as amended at 52 FR 45137, Nov. 24, 1987]



Sec. 52.28  Protection of visibility from sources in nonattainment areas.

    (a) Plan disapproval. The provisions of this section are applicable 
to any State implementation plan which has been disapproved with respect 
to protection of visibility, in mandatory Class I Federal areas where 
visibility is considered an important value, from sources emitting 
pollutants in any portion of

[[Page 43]]

any State where the existing air quality is not in compliance with the 
national ambient air quality standards for such pollutants. Specific 
disapprovals are listed where applicable in Subparts B through DDD of 
this part. The provisions of this section have been incorporated into 
the applicable implementation plans for various States, as provided in 
Subparts B through DDD of this part.
    (b) Definitions. For the purposes of this section:
    (1) Visibility protection area means any area listed in 40 CFR 
81.401-81.436 (1984).
    (2) All other terms shall have the meaning ascribed to them in the 
protection of visibility program (40 CFR 51.301) or the prevention of 
significant deterioration (PSD) program either approved as part of the 
applicable SIP pursuant to 40 CFR 51.24 or in effect for the applicable 
SIP pursuant to 40 CFR 52.21, all as in effect on July 12, 1985.
    (c) Review of major stationary sources and major modifications--
source applicability and exemptions. (1) No stationary source or 
modification to which the requirements of this section apply shall begin 
actual construction without a permit which states that the stationary 
source or modification would meet those requirements. The Administrator 
has sole authority to issue any such permit unless the authority has 
been delegated pursuant to paragraph (i) of this section.
    (2) The requirements of this section shall apply to construction of 
any new major stationary source or major modification that would both be 
constructed in an area classified as nonattainment under section 
107(d)(1)(A), (B) or (C) of the Clean Air Act and potentially have an 
impact on visibility in any visibility proctection area.
    (3) The requirements of this section shall apply to any such major 
stationary source and any such major modification with respect to each 
pollutant subject to regulation under the Clean Air Act that it would 
emit, except as this section otherwise provides.
    (4) The requirements of this section shall not apply to a particular 
major stationary source or major modification, if:
    (i) The source or modification would be a nonprofit health or 
nonprofit educational institution, or a major modification would occur 
at such an institution, and the governor of the State in which the 
source or modification would be located requests that it be exempt from 
those requirements; or
    (ii) The source or modification would be a major stationary source 
or major modification only if fugitive emissions, to the extent 
quantifiable, are considered in calculating the potential to emit of the 
stationary source or modification and the source does not belong to any 
of the following categories:
    (A) Coal cleaning plants (with thermal dryers);
    (B) Kraft pulp mills;
    (C) Portland cement plants;
    (D) Primary zinc smelters;
    (E) Iron and steel mills;
    (F) Primary aluminum ore reduction plants;
    (G) Primary copper smelters;
    (H) Municipal incinerators capable of charging more than 250 tons of 
refuse per day;
    (I) Hydrofluoric, sulfuric, or nitric acid plants;
    (J) Petroleum refineries;
    (K) Lime plants;
    (L) Phosphate rock processing plants;
    (M) Coke oven batteries;
    (N) Sulfur recovery plants;
    (O) Carbon black plants (furnace process);
    (P) Primary lead smelters;
    (Q) Fuel conversion plants;
    (R) Sintering plants;
    (S) Secondary metal production plants;
    (T) Chemical process plants;
    (U) Fossil-fuel boiler (or combination thereof) totaling more than 
250 million British thermal units per hour heat input;
    (V) Petroleum storage and transfer units with a total storage 
capacity exceeding 300,000 barrels;
    (W) Taconite ore processing plants;
    (X) Glass fiber processing plants;
    (Y) Charcoal production plants;
    (Z) Fossil fuel-fired steam electric plants of more than 250 million 
British thermal units per hour heat input;
    (AA) Any other stationary source category which, as of August 7, 
1980, is being regulated under section 111 or 112 of the Act; or

[[Page 44]]

    (iii) The source is a portable stationary source which has 
previously received a permit under this section, and
    (A) The owner or operator proposes to relocate the source and 
emissions of the source at the new location would be temporary; and
    (B) The emissions from the source would not exceed its allowable 
emissions; and
    (C) The emissions from the source would impact no Class I area and 
no area where an applicable increment is known to be violated; and
    (D) Reasonable notice is given to the Administrator, prior to the 
relocation, identifying the proposed new location and the probable 
duration of operation at the new location. Such notice shall be given to 
the Administrator not less than 10 days in advance of the proposed 
relocation, unless a different time duration is previously approved by 
the Administrator.
    (5) The requirements of this section shall not apply to a major 
stationary source or major modification with respect to a particular 
pollutant if the owner or operator demonstrates that, as to that 
pollutant, the source or modification is located in an area designated 
as attainment under section 107 of the Clean Air Act.
    (6) The requirements of this section shall not apply to a major 
stationary source or major modification with respect to a particular 
pollutant, if the allowable emissions of that pollutant from the source, 
or the net emissions increase of that pollutant from the modification:
    (i) Would impact no Class I area and no area where an applicable 
increment is known to be violated, and
    (ii) Would be temporary.
    (d) Visibility Impact Analyses. The owner or operator of a source 
shall provide an analysis of the impairment to visibility that would 
occur as a result of the source or modification and general commercial, 
residential, industrial and other growth associated with the source or 
modification.
    (e) Federal land manager notification. (1) The Federal land manager 
and the Federal official charged with direct responsibility for 
management of Federal Class I areas have an affirmative responsibility 
to protect the air quality related values (including visibility) of such 
lands and to consider, in consultation with the Administrator, whether a 
proposed source or modification will have an adverse impact on such 
values.
    (2) The Administrator shall provide written notification to all 
affected Federal land managers of any permit application for any 
proposed new major stationary source or major modification that may 
affect visibility in any visibility protection area.The Administrator 
shall also provide for such notification to the Federal official charged 
with direct responsibility for management of any lands within any such 
area. Such notification shall include a copy of all information relevant 
to the permit application and shall be given within 30 days of receipt 
and at least 60 days prior to any public hearing on the application for 
a permit to construct. Such notification shall include an analysis of 
the proposed source's anticipated impacts on visibility in any 
visibility protection area. The Administrator shall also notify all 
affected FLM's within 30 days of receipt of any advance notification of 
any such permit application.
    (3) The Administrator shall consider any analysis performed by the 
Federal land manager, provided within 30 days of the notification 
required by paragraph (e)(2) of this section, that such proposed new 
major stationary source or major modification may have an adverse impact 
on visibility in any visibility protection area. Where the Administrator 
finds that such an analysis does not demonstrate to the satisfaction of 
the Administrator that an adverse impact on visibility will result in 
the visibility protection area, the Administrator must, in the notice of 
public hearing, either explain his decision or give notice as to where 
the explanation can be obtained.
    (f) Public participation. The Administrator shall follow the 
applicable procedures of 40 CFR part 124 in processing applications 
under this section. The Administrator shall follow the procedures at 40 
CFR 52.21(q) as in effect on August 7, 1980, to the extent that the 
procedures of 40 CFR part 124 do not apply.
    (g) National visibility goal. The Administrator shall only issue 
permits to

[[Page 45]]

those sources whose emissions will be consistent with making reasonable 
progress toward the national goal of preventing any future, and 
remedying any existing, impairment of visibility in visibility 
protection areas which impairment results from man-made air pollution. 
In making the decision to issue a permit, the Administrator may take 
into account the costs of compliance, the time necessary for compliance, 
the energy and nonair quality environmental impacts of compliance, and 
the useful life of the source.
    (h) Monitoring. The Administrator may require monitoring of 
visibility in any visibility protection area near the proposed new 
stationary source or major modification for such purposes and by such 
means as the Administrator deems necessary and appropriate.
    (i) Delegation of authority. (1) The Administrator shall have the 
authority to delegate the responsibility for conducting source review 
pursuant to this section to any agency in accordance with paragraphs 
(i)(2) and (3) of this section.
    (2) Where the Administrator delegates the responsibility for 
conducting source review under this section to any agency other than a 
Regional Office of the Environmental Protection Agency, the following 
provisions shall apply:
    (i) Where the delegate agency is not an air pollution control agency 
it shall consult with the appropriate State and local air pollution 
control agency prior to making any determination under this section. 
Similarly, where the delegate agency does not have continuing 
responsibility for managing land use, it shall consult with the 
appropriate State and local agency primarily responsible for managing 
land use prior to making any determination under this section.
    (ii) The delegate agency shall submit a copy of any public comment 
notice required under paragraph (f) of this section to the Administrator 
through the appropriate Regional Office.
    (3) The Administrator's authority for reviewing a source or 
modification located on an Indian Reservation shall not be redelegated 
other than to a Regional Office of the Environmental Protection Agency, 
except where the State has assumed jurisdiction over such land under 
other laws. Where the State has assumed such jurisdiction, the 
Administrator may delegate his authority to the States in accordance 
with paragraph (i)(2) of this section.
[50 FR 28551, July 12, 1985]



Sec. 52.29  Visibility long-term strategies.

    (a) Plan disapprovals. The provisions of this section are applicable 
to any State implementation plan which has been disapproved for not 
meeting the requirements of 40 CFR 51.306 regarding the development, 
periodic review, and revision of visibility long-term strategies. 
Specific disapprovals are listed where applicable in Subparts B through 
DDD of this part. The provisions of this section have been incorporated 
into the applicable implementation plan for various States, as provided 
in Subparts B through DDD of this part.
    (b) Definitions. For the purposes of this section, all terms shall 
have the meaning as ascribed to them in the Clean Air Act, or in the 
protection of visibility program (40 CFR 51.301).
    (c) Long-term strategy. (1) A long-term strategy is a 10- to 15-year 
plan for making reasonable progress toward the national goal specified 
in Sec. 51.300(a). This strategy will cover any existing impairment 
certified by the Federal land manager and any integral vista which has 
been identified according to Sec. 51.304.
    (2) The Administrator shall review, and revise if appropriate, the 
long-term strategies developed for each visibility protection area. The 
review and revisions will be completed no less frequently than every 3 
years from November 24, 1987.
    (3) During the long-term strategy review process, the Administrator 
shall consult with the Federal land managers responsible for the 
appropriate mandatory Class I Federal areas, and will coordinate long-
term strategy development for an area with existing plans and goals, 
including those provided by the Federal land managers.
    (4) The Administrator shall prepare a report on any progress made 
toward the national visibility goal since the last long-term strategy 
revisions. A report will be made available to the public not less 
frequently than 3 years

[[Page 46]]

from November 24, 1987. This report must include an assessment of:
    (i) The progress achieved in remedying existing impairment of 
visibility in any mandatory Class I Federal area;
    (ii) The ability of the long-term strategy to prevent future 
impairment of visibility in any mandatory Class I Federal area;
    (iii) Any change in visibility since the last such report, or in the 
case of the first report, since plan approval;
    (iv) Additional measures, including the need for SIP revisions, that 
may be necessary to assure reasonable progress toward the national 
visibility goal;
    (v) The progress achieved in implementing best available retrofit 
technology (BART) and meeting other schedules set forth in the long-term 
strategy;
    (vi) The impact of any exemption granted under Sec. 51.303;
    (vii) The need for BART to remedy existing visibility impairment of 
any integral vista identified pursuant to Sec. 51.304.
    (d) Delegation of authority. The Administrator may delegate with 
respect to a particular visibility protection area any of his functions 
under this section, except the making of regulations, to any State or 
local air pollution control agency of any State whose boundaries 
encompass that area.
[52 FR 45137, Nov. 24, 1987]



Sec. 52.30  Criteria for limiting application of sanctions under section 110(m) of the Clean Air Act on a statewide basis.

    (a) Definitions. For the purpose of this section:
    (1) The term ``political subdivision'' refers to the representative 
body that is responsible for adopting and/or implementing air pollution 
controls for one, or any combination of one or more of the following: 
city, town, borough, county, parish, district, or any other geographical 
subdivision created by, or pursuant to, Federal or State law. This will 
include any agency designated under section 174, 42 U.S.C. 7504, by the 
State to carry out the air planning responsibilities under part D.
    (2) The term ``required activity'' means the submission of a plan or 
plan item, or the implementation of a plan or plan item.
    (3) The term ``deficiency'' means the failure to perform a required 
activity as defined in paragraph (a)(2) of this section.
    (4) For purposes of Sec. 52.30, the terms ``plan'' or ``plan item'' 
mean an implementation plan or portion of an implementation plan or 
action needed to prepare such plan required by the Clean Air Act, as 
amended in 1990, or in response to a SIP call issued pursuant to section 
110(k)(5) of the Act.
    (b) Sanctions. During the 24 months after a finding, determination, 
or disapproval under section 179(a) of the Clean Air Act is made, EPA 
will not impose sanctions under section 110(m) of the Act on a statewide 
basis if the Administrator finds that one or more political subdivisions 
of the State are principally responsible for the deficiency on which the 
finding, disapproval, or determination as provided under section 
179(a)(1) through (4) is based.
    (c) Criteria. For the purposes of this provision, EPA will consider 
a political subdivision to be principally responsible for the deficiency 
on which a section 179(a) finding is based, if all five of the following 
criteria are met.
    (1) The State has provided adequate legal authority to a political 
subdivision to perform the required activity.
    (2) The required activity is one which has traditionally been 
performed by the local political subdivision, or the responsibility for 
performing the required activity has been delegated to the political 
subdivision.
    (3) The State has provided adequate funding or authority to obtain 
funding (when funding is necessary to carry out the required activity) 
to the political subdivision to perform the required activity.
    (4) The political subdivision has agreed to perform (and has not 
revoked that agreement), or is required by State law to accept 
responsibility for performing, the required activity.
    (5) The political subdivision has failed to perform the required 
activity.
    (d) Imposition of sanctions. (1) If all of the criteria in paragraph 
(c) of this section have been met through the action or inaction of one 
political subdivision,

[[Page 47]]

EPA will not impose sanctions on a statewide basis.
    (2) If not all of the criteria in paragraph (c) of this section have 
been met through the action or inaction of one political subdivision, 
EPA will determine the area for which it is reasonable and appropriate 
to apply sanctions.
[59 FR 1484, Jan. 11, 1994]



Sec. 52.31  Selection of sequence of mandatory sanctions for findings made pursuant to section 179 of the Clean Air Act.

    (a) Purpose. The purpose of this section is to implement 42 U.S.C. 
7509(a) of the Act, with respect to the sequence in which sanctions will 
automatically apply under 42 U.S.C. 7509(b), following a finding made by 
the Administrator pursuant to 42 U.S.C. 7509(a).
    (b) Definitions. All terms used in this section, but not 
specifically defined herein, shall have the meaning given them in 
Sec. 52.01.
    (1) 1990 Amendments means the 1990 Amendments to the Clean Air Act 
(Pub. L. No. 101-549, 104 Stat. 2399).
    (2) Act means Clean Air Act, as amended in 1990 (42 U.S.C. 7401 et 
seq. (1991)).
    (3) Affected area means the geographic area subject to or covered by 
the Act requirement that is the subject of the finding and either, for 
purposes of the offset sanction under paragraph (e)(1) of this section 
and the highway sanction under paragraph (e)(2) of this section, is or 
is within an area designated nonattainment under 42 U.S.C. 7407(d) or, 
for purposes of the offset sanction under paragraph (e)(1) of this 
section, is or is within an area otherwise subject to the emission 
offset requirements of 42 U.S.C. 7503.
    (4) Criteria pollutant means a pollutant for which the Administrator 
has promulgated a national ambient air quality standard pursuant to 42 
U.S.C. 7409 (i.e., ozone, lead, sulfur dioxide, particulate matter, 
carbon monoxide, nitrogen dioxide).
    (5) Findings or Finding refer(s) to one or more of the findings, 
disapprovals, and determinations described in subsection 52.31 (c).
    (6) NAAQS means national ambient air quality standard the 
Administrator has promulgated pursuant to 42 U.S.C. 7409.
    (7) Ozone precursors mean nitrogen oxides (NOx) and 
volatile organic compounds (VOC).
    (8) Part D means part D of title I of the Act.
    (9) Part D SIP or SIP revision or plan means a State implementation 
plan or plan revision that States are required to submit or revise 
pursuant to part D.
    (10) Precursor means pollutant which is transformed in the 
atmosphere (later in time and space from point of emission) to form (or 
contribute to the formation of) a criteria pollutant.
    (c) Applicability. This section shall apply to any State in which an 
affected area is located and for which the Administrator has made one of 
the following findings, with respect to any part D SIP or SIP revision 
required under the Act:
    (1) A finding that a State has failed, for an area designated 
nonattainment under 42 U.S.C. 7407(d), to submit a plan, or to submit 
one or more of the elements (as determined by the Administrator) 
required by the provisions of the Act applicable to such an area, or has 
failed to make a submission for such an area that satisfies the minimum 
criteria established in relation to any such element under 42 U.S.C. 
7410(k);
    (2) A disapproval of a submission under 42 U.S.C. 7410(k), for an 
area designated nonattainment under 42 U.S.C. 7407(d), based on the 
submission's failure to meet one or more of the elements required by the 
provisions of the Act applicable to such an area;
    (3)(i) A determination that a State has failed to make any 
submission required under the Act, other than one described under 
paragraph (c)(1) or (c)(2) of this section, including an adequate 
maintenance plan, or has failed to make any submission, required under 
the Act, other than one described under paragraph (c)(1) or (c)(2) of 
this section, that satisfies the minimum criteria established in 
relation to such submission under 42 U.S.C. 7410(k)(1)(A); or
    (ii) A disapproval in whole or in part of a submission described 
under paragraph (c)(3)(i) of this section; or

[[Page 48]]

    (4) A finding that any requirement of an approved plan (or approved 
part of a plan) is not being implemented.
    (d) Sanction application sequencing. (1) To implement 42 U.S.C. 
7509(a), the offset sanction under paragraph (e)(1) of this section 
shall apply in an affected area 18 months from the date when the 
Administrator makes a finding under paragraph (c) of this section unless 
the Administrator affirmatively determines that the deficiency forming 
the basis of the finding has been corrected. To further implement 42 
U.S.C. 7509(a), the highway sanction under paragraph (e)(2) of this 
section shall apply in an affected area 6 months from the date the 
offset sanction under paragraph (e)(1) of this section applies, unless 
the Administrator affirmatively determines that the deficiency forming 
the basis of the finding has been corrected. For the findings under 
paragraphs (c)(2), (c)(3)(ii), and (c)(4) of this section, the date of 
the finding shall be the effective date as defined in the final action 
triggering the sanctions clock.
    (2)(i) Notwithstanding paragraph (d)(1) of this section, to further 
implement 42 U.S.C. 7509(a), following the findings under paragraphs 
(c)(2) and (c)(3)(ii) of this section, if the State has submitted a 
revised plan to correct the deficiency prompting the finding and the 
Administrator, prior to 18 months from the finding, has proposed to 
fully or conditionally approve the revised plan and has issued an 
interim final determination that the revised plan corrects the 
deficiency prompting the finding, application of the offset sanction 
under paragraph (e)(1) of this section shall be deferred unless and 
until the Administrator proposes to or takes final action to disapprove 
the plan in whole or in part. If the Administrator issues such a 
proposed or final disapproval of the plan, the offset sanction under 
paragraph (e)(1) of this section shall apply in the affected area on the 
later of the date the Administrator issues such a proposed or final 
disapproval, or 18 months following the finding that started the 
sanctions clock. The highway sanction under paragraph (e)(2) of this 
section shall apply in the affected area 6 months after the date the 
offset sanction under paragraph (e)(1) of this section applies, unless 
the Administrator determines that the deficiency forming the basis of 
the finding has been corrected.
    (ii) Notwithstanding paragraph (d)(1) of this section, to further 
implement 42 U.S.C. 7509(a), following the findings under paragraphs 
(c)(2) and (c)(3)(ii) of this section, if the State has submitted a 
revised plan to correct the deficiency prompting the finding and after 
18 but before 24 months from the finding the Administrator has proposed 
to fully or conditionally approve the revised plan and has issued an 
interim final determination that the revised plan corrects the 
deficiency prompting the finding, application of the offset sanction 
under paragraph (e)(1) of this section shall be stayed and application 
of the highway sanction under paragraph (e)(2) of this section shall be 
deferred unless and until the Administrator proposes to or takes final 
action to disapprove the plan in whole or in part. If the Administrator 
issues such a proposed or final disapproval of the plan, the offset 
sanction under paragraph (e)(1) of this section shall reapply in the 
affected area on the date the Administrator issues such a proposed or 
final disapproval. The highway sanction under paragraph (e)(2) of this 
section shall apply in the affected area on the later of 6 months from 
the date the offset sanction under paragraph (e)(1) of this section 
first applied in the affected area, unless the Administrator determines 
that the deficiency forming the basis of the finding has been corrected, 
or immediately if the proposed or final disapproval occurs more than 6 
months after initial application of the offset sanction under paragraph 
(e)(1) of this section.
    (iii) Notwithstanding paragraph (d)(1) of this section, to further 
implement 42 U.S.C. 7509(a), following the findings under paragraphs 
(c)(2) and (c)(3)(ii) of this section, if the State has submitted a 
revised plan to correct the deficiency prompting the finding and more 
than 24 months after the finding the Administrator has proposed to fully 
or conditionally approve the revised plan and has issued an interim 
final determination that the revised plan corrects the deficiency 
prompting the finding, application of the offset sanction under

[[Page 49]]

paragraph (e)(1) of this section and application of the highway sanction 
under paragraph (e)(2) of this section shall be stayed unless and until 
the Administrator proposes to or takes final action to disapprove the 
plan in whole or in part. If the Administrator issues such a proposed or 
final disapproval, the offset sanction under paragraph (e)(1) of this 
section and the highway sanction under paragraph (e)(2) of this section 
shall reapply in the affected area on the date the Administrator issues 
such proposed or final disapproval.
    (3)(i) Notwithstanding paragraph (d)(1) of this section, to further 
implement 42 U.S.C. 7509(a), following the findings under paragraphs 
(c)(2) and (c)(3)(ii) of this section, if the State has submitted a 
revised plan to correct the deficiency prompting the finding and the 
Administrator, prior to 18 months from the finding, has conditionally-
approved the revised plan and has issued an interim final determination 
that the revised plan corrects the deficiency prompting the finding, 
application of the offset sanction under paragraph (e)(1) of this 
section shall be deferred unless and until the conditional approval 
converts to a disapproval or the Administrator proposes to or takes 
final action to disapprove in whole or in part the revised SIP the State 
submits to fulfill the commitment in the conditionally-approved plan. If 
the conditional approval so becomes a disapproval or the Administrator 
issues such a proposed or final disapproval, the offset sanction under 
paragraph (e)(1) of this section shall apply in the affected area on the 
later of the date the approval becomes a disapproval or the 
Administrator issues such a proposed or final disapproval, whichever is 
applicable, or 18 months following the finding that started the 
sanctions clock. The highway sanction under paragraph (e)(2) of this 
section shall apply in the affected area 6 months after the date the 
offset sanction under paragraph (e)(1) of this section applies, unless 
the Administrator determines that the deficiency forming the basis of 
the finding has been corrected.
    (ii) Notwithstanding paragraph (d)(1) of this section, to further 
implement 42 U.S.C. 7509(a), following the findings under paragraphs 
(c)(2) and (c)(3)(ii) of this section, if the State has submitted a 
revised plan to correct the deficiency prompting the finding and after 
18 but before 24 months from the finding the Administrator has 
conditionally approved the revised plan and has issued an interim final 
determination that the revised plan corrects the deficiency prompting 
the finding, application of the offset sanction under paragraph (e)(1) 
of this section shall be stayed and application of the highway sanction 
under paragraph (e)(2) of this section shall be deferred unless and 
until the conditional approval converts to a disapproval or the 
Administrator proposes to or takes final action to disapprove in whole 
or in part the revised SIP the State submits to fulfill the commitment 
in the conditionally-approved plan. If the conditional approval so 
becomes a disapproval or the Administrator issues such a proposed or 
final disapproval, the offset sanction under paragraph (e)(1) of this 
section shall reapply in the affected area on the date the approval 
becomes a disapproval or the Administrator issues such a proposed or 
final disapproval, whichever is applicable. The highway sanction under 
paragraph (e)(2) of this section shall apply in the affected area on the 
later of 6 months from the date the offset sanction under paragraph 
(e)(1) of this section first applied in the affected area, unless the 
Administrator determines that the deficiency forming the basis of the 
finding has been corrected, or immediately if the conditional approval 
becomes a disapproval or the Administrator issues such a proposed or 
final disapproval, whichever is applicable, more than 6 months after 
initial application of the offset sanction under paragraph (e)(1) of 
this section.
    (iii) Notwithstanding paragraph (d)(1) of this section, to further 
implement 42 U.S.C. 7509(a), following the findings under paragraphs 
(c)(2) and (c)(3)(ii) of this section, if the State has submitted a 
revised plan to correct the deficiency prompting the finding and after 
24 months from the finding the Administrator has conditionally approved 
the revised plan and has issued an interim final determination that the 
revised plan corrects the deficiency prompting the finding, application 
of the offset

[[Page 50]]

sanction under paragraph (e)(1) of this section and application of the 
highway sanction under paragraph (e)(2) of this section shall be stayed 
unless and until the conditional approval converts to a disapproval or 
the Administrator proposes to or takes final action to disapprove in 
whole or in part the revised SIP the State submits to fulfill its 
commitment in the conditionally-approved plan. If the conditional 
approval so becomes a disapproval or the Administrator issues such a 
proposed or final disapproval, the offset sanction under paragraph 
(e)(1) of this section and the highway sanction under paragraph (e)(2) 
of this section shall reapply in the affected area on the date the 
conditional approval becomes a disapproval or the Administrator issues 
such a proposed or final disapproval, whichever is applicable.
    (4)(i) Notwithstanding paragraph (d)(1) of this section, to further 
implement 42 U.S.C. 7509(a), following findings under paragraph (c)(4) 
of this section, if the Administrator, prior to 18 months from the 
finding, has proposed to find that the State is implementing the 
approved plan and has issued an interim final determination that the 
deficiency prompting the finding has been corrected, application of the 
offset sanction under paragraph (e)(1) of this section shall be deferred 
unless and until the Administrator preliminarily or finally determines, 
through a proposed or final finding, that the State is not implementing 
the approved plan and that, therefore, the State has not corrected the 
deficiency. If the Administrator so preliminarily or finally determines 
that the State has not corrected the deficiency, the offset sanction 
under paragraph (e)(1) of this section shall apply in the affected area 
on the later of the date the Administrator proposes to take action or 
takes final action to find that the finding of nonimplementation has not 
been corrected, or 18 months following the finding that started the 
sanctions clock. The highway sanction under paragraph (e)(2) of this 
section shall apply in the affected area 6 months after the date the 
offset sanction under paragraph (e)(1) of this section first applies, 
unless the Administrator preliminarily or finally determines that the 
deficiency forming the basis of the finding has been corrected.
    (ii) Notwithstanding paragraph (d)(1) of this section, to further 
implement 42 U.S.C. 7509(a), following findings under paragraph (c)(4) 
of this section, if after 18 months but before 24 months from the 
finding the Administrator has proposed to find that the State is 
implementing the approved plan and has issued an interim final 
determination that the deficiency prompting the finding has been 
corrected, application of the offset sanction under paragraph (e)(1) of 
this section shall be stayed and application of the highway sanction 
under paragraph (e)(2) of this section shall be deferred unless and 
until the Administrator preliminarily or finally determines, through a 
proposed or final finding, that the State is not implementing the 
approved plan and that, therefore, the State has not corrected the 
deficiency. If the Administrator so preliminarily or finally determines 
that the State has not corrected the deficiency, the offset sanction 
under paragraph (e)(1) of this section shall reapply in the affected 
area on the date the Administrator proposes to take action or takes 
final action to find that the finding of nonimplementation has not been 
corrected. The highway sanction under paragraph (e)(2) of this section 
shall apply in the affected area on the later of 6 months from the date 
the offset sanction under paragraph (e)(1) of this section first applied 
in the affected area, unless the Administrator preliminarily or finally 
determines that the deficiency forming the basis of the finding has been 
corrected, or immediately if EPA's proposed or final action finding the 
deficiency has not been corrected occurs more than 6 months after 
initial application of the offset sanction under paragraph (e)(1) of 
this section.
    (iii) Notwithstanding paragraph (d)(1) of this section, to further 
implement 42 U.S.C. 7509(a), following findings under paragraph (c)(4) 
of this section, if after 24 months from the finding the Administrator 
has proposed to find that the State is implementing the approved plan 
and has issued an interim final determination that the deficiency

[[Page 51]]

prompting the finding has been corrected, application of the offset 
sanction under paragraph (e)(1) of this section and the highway sanction 
under paragraph (e)(2) of this section shall be stayed unless and until 
the Administrator preliminarily or finally determines, through a 
proposed or final finding, that the State is not implementing the 
approved plan, and that, therefore, the State has not corrected the 
deficiency. If the Administrator so preliminarily or finally determines 
that the State has not corrected the deficiency, the offset sanction 
under paragraph (e)(1) of this section and the highway sanction under 
paragraph (e)(2) of this section shall reapply in the affected area on 
the date the Administrator proposes to take action or takes final action 
to find that the finding of nonimplementation has not been corrected.
    (5) Any sanction clock started by a finding under paragraph (c) of 
this section will be permanently stopped and sanctions applied, stayed 
or deferred will be permanently lifted upon a final EPA finding that the 
deficiency forming the basis of the finding has been corrected. For a 
sanctions clock and applied sanctions based on a finding under 
paragraphs (c)(1) and (c)(3)(i) of this section, a finding that the 
deficiency has been corrected will occur by letter from the 
Administrator to the State governor. For a sanctions clock or applied, 
stayed or deferred sanctions based on a finding under paragraphs (c)(2) 
and (c)(3)(ii) of this section, a finding that the deficiency has been 
corrected will occur through a final notice in the Federal Register 
fully approving the revised SIP. For a sanctions clock or applied, 
stayed or deferred sanctions based on a finding under paragraph (c)(4) 
of this section, a finding that the deficiency has been corrected will 
occur through a final notice in the Federal Register finding that the 
State is implementing the approved SIP.
    (6) Notwithstanding paragraph (d)(1) of this section, nothing in 
this section will prohibit the Administrator from determining through 
notice-and-comment rulemaking that in specific circumstances the highway 
sanction, rather than the offset sanction, shall apply 18 months after 
the Administrator makes one of the findings under paragraph (c) of this 
section, and that the offset sanction, rather than the highway sanction, 
shall apply 6 months from the date the highway sanction applies.
    (e) Available sanctions and method for implementation--(1) Offset 
sanction. (i) As further set forth in paragraphs (e)(1)(ii)-(e)(1)(vi) 
of this section, the State shall apply the emissions offset requirement 
in the timeframe prescribed under paragraph (d) of this section on those 
affected areas subject under paragraph (d) of this section to the offset 
sanction. The State shall apply the emission offset requirements in 
accordance with 42 U.S.C. 7503 and 7509(b)(2), at a ratio of at least 
two units of emission reductions for each unit of increased emissions of 
the pollutant(s) and its (their) precursors for which the finding(s) 
under paragraph (c) of this section is (are) made. If the deficiency 
prompting the finding under paragraph (c) of this section is not 
specific to one or more particular pollutants and their precursors, the 
2-to-1 ratio shall apply to all pollutants (and their precursors) for 
which an affected area within the State listed in paragraph (e)(1)(i) of 
this section is required to meet the offset requirements of 42 U.S.C. 
7503.
    (ii) Notwithstanding paragraph (e)(1)(i) of this section, when a 
finding is made with respect to a requirement for the criteria pollutant 
ozone or when the finding is not pollutant-specific, the State shall not 
apply the emissions offset requirements at a ratio of at least 2-to-1 
for emission reductions to increased emissions for nitrogen oxides 
where, under 42 U.S.C. 7511a(f), the Administrator has approved an 
NOX exemption for the affected area from the Act's new source 
review requirements under 42 U.S.C. 7501-7515 for NOX or 
where the affected area is not otherwise subject to the Act's new source 
review requirements for emission offsets under 42 U.S.C. 7501-7515 for 
NOX.
    (iii) Notwithstanding paragraph (e)(1)(i) of this section, when a 
finding under paragraph (c) of this section is made with respect to PM-
10, or the finding is not pollutant-specific, the

[[Page 52]]

State shall not apply the emissions offset requirements, at a ratio of 
at least 2-to-1 for emission reductions to increased emissions to PM-10 
precursors if the Administrator has determined under 42 U.S.C. 7513a(e) 
that major stationary sources of PM-10 precursors do not contribute 
significantly to PM-10 levels which exceed the NAAQS in the affected 
area.
    (iv) For purposes of applying the emissions offset requirement set 
forth in 42 U.S.C. 7503, at the 2-to-1 ratio required under this 
section, the State shall comply with the provisions of a State-adopted 
new source review (NSR) program that EPA has approved under 42 U.S.C. 
7410(k)(3) as meeting the nonattainment area NSR requirements of 42 
U.S.C. 7501-7515, as amended by the 1990 Amendments, or, if no plan has 
been so approved, the State shall comply directly with the nonattainment 
area NSR requirements specified in 42 U.S.C. 7501-7515, as amended by 
the 1990 Amendments, or cease issuing permits to construct and operate 
major new or modified sources as defined in those requirements. For 
purposes of applying the offset requirement under 42 U.S.C. 7503 where 
EPA has not fully approved a State's NSR program as meeting the 
requirements of part D, the specifications of those provisions shall 
supersede any State requirement that is less stringent or inconsistent.
    (v) For purposes of applying the emissions offset requirement set 
forth in 42 U.S.C. 7503, any permit required pursuant to 42 U.S.C. 7503 
and issued on or after the date the offset sanction applies under 
paragraph (d) of this section shall be subject to the enhanced 2-to-1 
ratio under paragraph (e)(1)(i) of this section.
    (2) Highway funding sanction. The highway sanction shall apply, as 
provided in 42 U.S.C. 7509(b)(1), in the timeframe prescribed under 
paragraph (d) of this section on those affected areas subject under 
paragraph (d) of this section to the highway sanction, but shall apply 
only to those portions of affected areas that are designated 
nonattainment under 40 CFR part 81.
[59 FR 39859, Aug. 4, 1994]



Sec. 52.32  Sanctions following findings of SIP inadequacy.

    For purposes of the SIP revisions required by Sec. 51.120, EPA may 
make a finding under section 179(a) (1)-(4) of the Clean Air Act, 42 
U.S.C. 7509(a) (1)-(4), starting the sanctions process set forth in 
section 179(a) of the Clean Air Act. Any such finding will be deemed a 
finding under Sec. 52.31(c) and sanctions will be imposed in accordance 
with the order of sanctions and the terms for such sanctions established 
in Sec. 52.31.
[60 FR 4737, Jan. 24, 1995]



Sec. 52.33  Compliance certifications.

    (a) For the purpose of submitting compliance certifications, nothing 
in this part or in a plan promulgated by the Administrator shall 
preclude the use, including the exclusive use, of any credible evidence 
or information, relevant to whether a source would have been in 
compliance with applicable requirements if the appropriate performance 
or compliance test had been performed.
    (b) For all federal implementation plans, paragraph (a) of this 
section is incorporated into the plan.
[62 FR 8328, Feb. 24, 1997]



                           Subpart B--Alabama



Sec. 52.50  Identification of plan.

    (a) Title of plan: ``Air Quality Implementation Plan for the State 
of Alabama.''
    (b) The plan was officially submitted on January 25, 1972.
    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) Letter informing Governor of Florida of submittal of Alabama 
Implementation Plan submitted on March 21, 1972, by the Alabama Air 
Pollution Control Commission.
    (2) Compliance schedules submitted on April 18, 1972, by the Alabama 
Air Pollution Control Commission.
    (3) Clarifying comments on the plan submitted on April 28, 1972, by 
the Alabama Air Pollution Control Commission.
    (4) Semi-annual report, miscellaneous non-regulatory additions to 
the plan, compliance schedules and miscellaneous regulatory additions to

[[Page 53]]

Chapters 3, 4, 5 and 9 submitted on February 15, 1973, by the Alabama 
Air Pollution Control Commission.
    (5) Transportation control plans submitted on April 24, 1973, by the 
Alabama Air Pollution Control Commission.
    (6) Miscellaneous non-regulatory additions to the plan submitted on 
June 29, 1973, by the Alabama Air Pollution Control Commission.
    (7) Miscellaneous non-regulatory additions and complex source 
regulation, Chapter 10, submitted on September 26, 1973, by the Alabama 
Air Pollution Control Commission.
    (8) Plan revisions to Chapter 5 concerning sulfur compound emissions 
submitted on October 31, 1973, by the Alabama Air Pollution Control 
Commission.
    (9) Revision to Part 4.10, Primary Aluminum Plants, and redefinition 
of ``Solid Particulate Matter'' in section 1.2.1 submitted on May 27, 
1974, by the Alabama Air Pollution Control Commission.
    (10) AQMA identifications submitted on June 17, 1974, by the Alabama 
Air Pollution Control Commission.
    (11) Coke oven regulations, Part 4.9 excluding section 4.9.4, 
submitted on June 20, 1974, by the Alabama Air Pollution Control 
Commission.
    (12) Revised limits on particulate emissions from Portland cement 
plants, submitted on June 4, 1975, by the Alabama Air Pollution Control 
Commission.
    (13) Revised limits on sulfur dioxide and sulfuric acid mist 
emissions from sulfuric acid plants, submitted on July 25, 1975, by the 
Alabama Air Pollution Control Commission.
    (14) Revised area classification system for fuel combustion sources 
of sulfur dioxide and initial classification of Counties, submitted on 
May 1 and October 9, 1975, respectively, by the Alabama Air Pollution 
Control Commission.
    (15) Revised emergency level for photochemical oxidants (emergency 
episode control plan) submitted by the Alabama Air Pollution Control 
Commission on April 23, 1976.
    (16) Revised SO2 emissions from gas processing plants 
submitted by the Alabama Air Pollution Control Commission on July 21, 
1976.
    (17) Regulations equivalent to EPA's New Source Performance 
Standards (40 CFR part 60) and continuous monitoring requirements for 
existing stationary sources (40 CFR 51.19), submitted by the Alabama Air 
Pollution Control Commission on October 28, 1976.
    (18) Revised regulations for the charging and pushing of coke in 
existing conventional batteries, submitted by the Alabama Air Pollution 
Control Commission on July 14, 1978.
    (19) Part 4.12, dealing with particulate emissions from xylene 
oxidation, submitted by the Alabama Air Pollution Control Commission on 
September 13, 1978.
    (20) 1979 implementation plan revisions for nonattainment areas (TSP 
and ozone), submitted on April 19, 1979, (as clarified by a letter of 
August 10, 1979), by the Alabama Air Pollution Control Commission.
    (21) Revisions in permit regulations as follows: (i) Title of 
16.3.2. is changed to ``Permits to Construct in or near Nonattainment 
Areas;'' (ii) a subparagraph (9), ``Significant Impact,'' is added to 
paragraph 16.3.2.(b); (iii) paragraph 16.3.2.(c) is revised; and (iv) 
subparagraph 16.3.2.(d)(5) is deleted; these revisions were adopted on 
February 13, 1980, and submitted on February 20, 1980, by the Alabama 
Air Pollution Control Commission to correct deficiencies in the Part D 
revisions given conditional approval by EPA on November 26, 1979.
    (22) 1979 implementation plan revisions for sulfur dioxide 
nonattainment areas in Colbert, Lauderdale, and Jackson Counties, 
adopted on August 28, 1979, and submitted on September 6, 1979 by the 
Alabama Air Pollution Control Commission.
    (23) Request for an 18-month extension of the statutory deadline for 
submitting a plan to attain and maintain the secondary standard for 
sulfur dioxide in the Jackson County nonattainment area, submitted on 
September 6, 1979, by the Alabama Air Pollution Control Commission.
    (24) Revision to the State Implementation Plan to delete the 
indirect source regulations submitted by the

[[Page 54]]

Alabama Air Pollution Control Commission on December 12, 1978.
    (25) Revised emergency episode control plan, updating procedures and 
raising the alert level for ozone from 0.10 ppm to 0.15 ppm, submitted 
by the Alabama Air Pollution Control Commission on January 11, 1980.
    (26) Revision to the State Implementation Plan for an air quality 
surveillance network was submitted by the Alabama Air Pollution Control 
Commission on January 9, 1980.
    (27) Alternative compliance schedules for nine sources of volatile 
organic compounds, submitted by the Alabama Air Pollution Control 
Commission on July 3, 1980.
    (28) Revisions to Chapter 6 of the Alabama Rules and Regulations 
were submitted by the Alabama Air Pollution Control Commission on April 
1, 1981.
    (29) Alternative TSP control strategy for 3M Company's Guin plant, 
submitted on February 4, 1981, by the Alabama Air Pollution Control 
Commission.
    (30) Revisions in Chapters 12 and 13, adopting Federal NSPS and 
NESHAPS regulations by reference, submitted by the Alabama Air Pollution 
Control Commission on June 26, 1981.
    (31) Alternative compliance schedules for VOC sources, submitted on 
June 25, 1981, by the Alabama Air Pollution Control Commission.
    (32) Regulations providing for prevention of significant 
deterioration (additions to Chapter 16 of the Alabama regulations), 
submitted on January 29, 1981, by the Alabama Air Pollution Control 
Commission.
    (33) Alternative particulate control requirements for Kimberly-Clark 
Corporation's 3 bark boiler, Coosa Pines (revisions in Part 4.8 of the 
Alabama regulations), submitted by the Alabama Air Pollution Control 
Commission on February 4 and August 31, 1981.
    (34) Request for 18-month extension of the deadline for submitting a 
plan to attain and maintain the secondary ambient standard for 
particulate matter in the Etowah County nonattainment area, submitted on 
May 19, 1981, by the Alabama Air Pollution Control Commission.
    (35) Revision for Jackson County secondary sulfur dioxide 
nonattainment area, submitted on June 9, 1980, by the Alabama Air 
Pollution Control Commission.
    (36) Set II VOC regulations, submitted on February 12, 1982, by the 
Alabama Air Pollution Control Commission and on May 5, 1983, by the 
Alabama Department of Environmental Management.
    (37) Provisions for new source review in nonattainment areas 
(changes in Chapter 16 of the regulations), submitted on March 31, 1981, 
by the Alabama Air Pollution Control Commission.
    (38) Bubble for Union Camp Corporation's Prattville, Alabama kraft 
pulp mill, submitted on January 21, 1983, January 20, 1984, and March 9, 
1984, by the Alabama Department of Environmental Management (ADEM).
    (i) Incorporation by reference.
    (A) Alabama Department of Environmental Management Resolution and 
Regulation 4.8.4, dealing with control of particulate emissions from 
wood waste boilers, was adopted on December 9, 1983.
    (B) Alabama Environmental Management Commission Resolution and 
Regulation 4.7.5, dealing with particulate emissions from kraft pulp 
mills, was adopted on March 7, 1984.
    (ii) Other material.
    (A) None.
    (39) Changes to air permit requirements, submitted on February 19, 
1985, and on March 28, 1985, by the Alabama Department of Environmental 
Management (ADEM).
    (i) Incorporation by reference.
    (A) Amendment to ADEM Air Rules & Regulations Chapter 16.1, 
submitted on March 28, 1985, and State-adopted on March 13, 1985. Allows 
delegation of permitting authority to locals.
    (B) Amendment to ADEM Air Rules & Regulations Chapter 16.1, 16.2, 
16.3, and 16.4, submitted on February 19, 1985, and State-adopted on 
February 13, 1985. Consolidates Permit to Construct, Operate and 
Temporary Permit, into one Air Permit.
    (ii) Additional information.
    (A) None.
    (40) Visibility new source review regulations as visibility 
monitoring strategy were submitted to EPA on November 20, 1985.
    (i) Incorporated by reference.

[[Page 55]]

    (A) Letter of November 20, 1985, from the Alabama Department of 
Environmental Management, and the following regulation Changes to 
Paragraphs 16.3.2 and 16.4 to Address Visibility Requirements adopted by 
the Alabama Environmental Management Commission on November 13, 1985:

16.3.2(b)--(Permits to Construct in or Near Nonattainment Areas--
Definitions)
16.3.2(f)--(Permits to Construct in or Near Nonattainment Areas--
visibility protection provisions)
16.4.2--(Permits to Construct in Clean Air Areas--Definitions)
16.4.12--(Visibility Monitoring)
16.4.15--(Sources Impacting Federal Class I Areas--Additional 
Requirements)

    (ii) Additional material.
    (A) Narrative Visibility SIP which includes the State's visibility 
monitoring strategy.
    (41) State implementation plan revisions, submitted by the 
Department of Environmental Management on May 17, 1985.
    (i) Incorporation by reference.
    (A) Amendments to Alabama Department of Environmental Management's 
(ADEM) Air Rules and Regulations: addition of Paragraphs 4.3.5, 4.7.6, 
4.7.7, 4.8.3(a), 4.8.3(b), 4.8.3(c), revision of Paragraph 4.8.3, 
adopted on October 10, 1984.
    (B) Resolution by the Alabama Environmental Management Commission 
adopting the proposed regulations into the ADEM's Air Rules and 
Regulations on October 10, 1984.
    (ii) Other material.
    (A) Dispersion modelling of area around Kimberly Clark Corporation's 
Talledega County facility.
    (42) State implementation plan for attainment and maintenance of the 
lead standards in all areas except Jefferson County, submitted on March 
28, 1985, by the Alabama Department of Environmental Management.
    (i) Incorporation by reference.
    (A) Regulation for existing secondary lead smelters located in Pike 
County, Alabama (Regulation 4.15.6), which was adopted by the Alabama 
Department of Environmental Management on March 13, 1985. Under 
applicable law, EPA approval is required for discretionary actions of 
the Director of the Alabama Department of Environmental Management that 
may increase lead concentrations in the ambient air.
    (B) Letter of May 6, 1985 from Ababama Department of Environmental 
Management to EPA, and Regulation pertaining to secondary lead smelter 
exhaust stack gases (Regulation 4.15.3), which was adopted by the 
Alabama Air Pollution Control Commission on March 23, 1982.
    (ii) Other material.
    (A) Narrative SIP, titled, ``State of Alabama'a Plan for the 
Attainment of the National Ambient Air Quality Standard for Lead,'' 
dated December 1984.
    (43) [Reserved]
    (44) Volatile Organic Compound regulation changes were submitted to 
EPA on September 23, 1985.
    (i) Incorporation by reference. (A) Letter of September 23, 1985 to 
EPA from Alabama Department of Environmental Management and changes to 
Chapter 6 of the Alabama Air Pollution Control Rules and Regulations 
(Control of Volatile Organic Compounds) which were adopted by the 
Alabama Environmental Management Commission on September 18, 1985, 
specifically, the revisions to 6.1.1(a), 6.1.2, and 6.1.3 and the 
addition of 6.1.4 and 6.1.5.
    (ii) Other material--none.
    (45) State implementation plan for attainment and maintenance of 
lead standards in Jefferson County, submitted on October 7, 1985, by the 
Alabama Department of Environmental Management, and on November 13, 
1986, by the Jefferson County Health Department.
    (i) Incorporation by reference.
    (A) Jefferson County Department of Health Regulation 611, Secondary 
Lead Smelters (excluding paragraphs 6.11.2(a) and 6.11.2(b)) which was 
adopted on September 11, 1985.
    (B) November 13, 1986, letter to EPA from the Jefferson County 
Department of Health, and Appendix C of the Alabama Lead SIP for 
Jefferson County (Revised Schedule for the RACT-plus study) which was 
adopted on November 12, 1986.
    (ii) Other material.
    (A) Narrative SIP, entitled ``State Implementation Plan for the 
Attainment of the National Ambient Air Quality Standard for Lead in 
Jefferson County'' dated September 1984.

[[Page 56]]

    (46) Stack height regulations were submitted to EPA on September 26, 
1986, by the Alabama Department of Environmental Management.
    (i) Incorporation by reference.
    (A) Letter of September 26, 1986, from the Alabama Department of 
Environmental Management, transmitting stack height regulations.
    (B) Section 16.3.3, Stack Heights, of the Alabama air pollution 
control rules and regulations, which was adopted on September 18, 1986, 
by the Alabama Environmental Management Commission.
    (ii) Other material--none.
    (47) Revisions to Alabama's New Source Review regulations were 
submitted to EPA on April 17, 1987.
    (i) Incorporation by reference.
    (A) Letter of April 17, 1987, from the Alabama Department of 
Environmental Management.
    (B) Revisions to Alabama regulation 16.3.2, adopted by the Alabama 
Department of Environmental Management (ADEM) on April 15, 1987.
    (ii) Other material--none.
    (48) Revised State Implementation Plan for attainment and 
maintenance of lead standards in Jefferson County, submitted on August 
5, 1988, by the Alabama Department of Environmental Management.
    (i) Incorporation by reference. (A) Air permits incorporating 
revised regulations for existing secondary lead smelters located in 
Jefferson County, Alabama (Regulation 6.11), adopted by the Jefferson 
County Board of Health on May 11, 1988.
    (B) [Reserved]
    (ii) Other material. (A) Narrative SIP, entitled ``State 
Implementation Plan for the Attainment of the National Ambient Air 
Quality Standard for Lead in Jefferson County,'' dated February 19, 
1988.
    (B) [Reserved]
    (49) SO2 revisions for Secondary Lead Smelters, submitted 
by the Alabama Department of Environmental Management on June 30, 1989.
    (i) Incorporation by reference.
    (A) The following revisions to Chapter 6 of Jefferson County Board 
of Health Air Pollution Control Rules and Regulations, which became 
effective June 14, 1989.

(1) 6.11.2(o)

    (B) The following revisions to chapter 7 of Jefferson County Board 
of Health Air Pollution Control Rules and Regulations which became 
effective June 14, 1989 as follows:

(1) 7.5.3  (3) 7.5.5
(2) 7.5.4  (4) 7.5.6

    (ii) Additional material. (A) Letter of June 30, 1989, submitted by 
the Alabama Department of Environmental Management.
    (B) Modeling analysis for Interstate Lead Corporation which was 
submitted by Jefferson County, Alabama on April 5, 1989.
    (50) Changes in Alabama's Regulations which were submitted to EPA on 
May 29, 1987, by the Alabama Department of Health and Environmental 
Management.
    (i) Incorporation by reference.
    (A) Changes in Alabama's Regulation which were adopted on May 20, 
1987:
    (1) Chapter 5, Control of Sulfur Compound Emissions: Section 
5.1.1(d) & (e) and Sections 5.3.4 (Applicability), 5.3.4 (a) & (b), 
5.3.5 (a) & (b), 5.3.6, 5.3.7, 5.3.8, & 5.3.9.
    (ii) Other Material.
    (A) Modeling analysis for Exxon Company's Big Escambia Creek 
Treating Facility and Tennessee Valley Authority's Colbert Steam Plant.
    (51) The recodified Air Division Administrative Code Rules of the 
Alabama Department of Environmental Management submitted on October 31, 
1989 as revisions to Alabama's State Implementation Plan. These rules 
became effective on June 22, 1989.
    (i) Incorporation by reference.
    (A) Alabama Department of Environmental Management Administrative 
Code Rules 335-3 and appendices A-F, revision effective June 22, 1989, 
except for the following rules:

335-3-1-.02(1)--Definitions: (b), (c), (j), (pp), (xx), (yy), (bbb), 
(ccc), (nnn), (sss), and (yyy).
335-3-2-.02--Episode Criteria: (4)(b); (4)(c), (d) and (e); and (5)(b), 
(c), (d), and (e); (6)(b), (c), (d), and (e).
335-3-4--Control of Particulate Emissions; .01(1)(a), (b), and (d)(1), 
(2), (3), (4), and (5); .01(2); and .04(1)(a)
335-3-5-.03--Petroleum Production: (4)
335-3-14--Permits: .03(1)(g)(1)

    (ii) Other material--None.

[[Page 57]]

    (52) Provisions for PM10 submitted on June 29, 1988, and 
October 3, 1989, by the Alabama Department of Environmental Management.
    (i) Incorporation by reference.
    (A) The following revisions submitted on June 29, 1988, to Chapters 
1, 2 and 16 were effective June 16, 1988. These Chapters were recodified 
as Chapters 335-3-1, 335-3-2 and 335-3-14, respectively, effective June 
22, 1989.
    (1) Definitions--1.2.1 recodified 335-3-1-.02(1) bbb, eee, nnn, and 
yyy.
    (2) Air Pollution Emergency--Chapter 2 recodified as 335-3-2.
    (3) Permits--Chapter 16 recodified as 335-3-14, except .03(1)(g)(1).
    (B) The following revisions submitted on October 3, 1989, to 
Chapters 35-3-1 and 335-3-14 were effective September 21, 1989.
    (1) Definitions--335-1-.02 (1) (yy) and (ccc).
    (2) Permits--335-3-14.
    (i) 335-3-14-.03(1)(g)(1).
    (53) October 8, 1988, and March 15, 1989, revisions to Jefferson 
County's Implementation Plan for PM10 were submitted by the 
Alabama Department of Environmental Management. The submittal included a 
committal SIP.
    (i) Incorporation by reference.
    (A) The following revisions submitted on March 15, 1989, to chapters 
1, 2, and 4 of Jefferson County Implementation Plan for PM10 
were effective February 8, 1989.

                Chapter I--Chapter I General Provisions:

                           1.3  (Definitions):

    Soiling Index, PM10, Particulate Matter, PM10 
emission, Total Suspended Particulate, Citation, Control Device, 
Employee, Six Minute Average, Violator.
    Chapter 2--Permits: 2.3.1(g)(1), (2), and (3); 2.3.2.(b)(11) and 20; 
2.3.4 (a)(5); 2.3.2 (2); 2.4.2.(w) (1) and (2); 2.4.3; 2.4.8(h), 
2.4.8(k) and (l); 2.4.12(a)(7) and 8; 2.4.15(e); and 2.4.19(a).
    Chapter 4--Air Pollution Emergency: 4.3.4(b), (c), (d), and (e); 
4.3.5(b), (c), (d), and (e); and 4.3.6(b), (c), (d), and (e).

    (ii) Other material.
    (A) March 15, 1989, letter from the Alabama Department of 
Environmental Management.
    (54)-(55) [Reserved]
    (56) Revisions to the VOC portion of the Alabama SIP were submitted 
on April 20, 1987, November 7, 1990, May 22, 1991, and October 4, 1991, 
and July 5, 1991, by the State of Alabama. These revisions were adopted 
on April 15, 1987; October 10, 1990; November 14, 1990, and May 8, 1991; 
September 18, 1991, respectively by the Jefferson County Board of 
Health.
    (i) Incorporation by reference.
    (A) Jefferson County Department of Health Air Pollution Control 
Program Rules and Regulations, Chapter 8 (Control of VOC Emissions) and 
Chapter 1 (Definitions) effective April 8, 1987.
    (1) Chapter 1--General Provisions: Section 1.3.
    (2) Chapter 8--Control of Volatile Organic Compound (VOC) Emissions, 
except for 8.16.13.
    (ii) Other material--none.
    (57) Revisions to Chapters 335-3-1 and 335-3-6 of the Alabama 
Department of Environmental Management Administrative Code which were 
submitted on October 19, 1989, and on July 5, 1991, and adopted into the 
Alabama Department of Environmental Management Administrative Code on 
August 16, 1989 and June 26, 1991.
    (i) Incorporation by reference.
    (A) Amendments to the Alabama regulations 335-3-1-.02, 335-3-
6-.02(1); 335-3-6-.03(1); 335-3-6-.24(1); 335-3-6-.26; 335-3-6-.27; 335-
3-6-.28; 335-3-6-.29; 335-3-6-.30; 335-3-6-.31; 335-3-6-.32; 335-3-
6-.33; 335-3-6-.34; 335-3-6-.35; 335-3-6-.36; 335-3-6-.37 with the 
exception of Subsection 335-3-6-.37(10)(a); 335-3-6-.38; 335-3-6-.39; 
335-3-6-40; 335-3-6-.41; 335-3-6-.42; 335-3-6-43; 335-3-6-44; 335-3-6-
45; 335-3-6-.46; 335-3-6-.47; 335-3-6-.49; 335-3-6-.51; 335-3-6-.53 
effective July 31, 1991.
    (ii) Other material--None.
    (58) Revisions to include NO2 increment requirements in 
Chapter 2 of the SIP and the PSD regulations, Chapter 335-3-14 of the 
Alabama Department of Environmental Management Administrative Code which 
was submitted on October 22, 1990.
    (i) Incorporation by reference. (A) Revisions to 335-3-14-.04, ``Air 
Permits Authorizing Construction in Clean Air Areas,'' of the Alabama 
Department of Enironmental Management Administrative Code, which became 
effective November 1, 1990.

[[Page 58]]

    (ii) Other material. (A) Letter dated October 22, 1990, from the 
Alabama Department of Environmental Management.
    (B) Letter dated April 30, 1991, from the Alabama Department of 
Environmental Management regarding minimum program elements.
    (59)  [Reserved]
    (60) Provisions for visible emissions were submitted by the Alabama 
Department of Environmental Management on June 11, 1979.
    (i) Incorporation by reference.
    (A) 335-3-4.01 Visible Emissions, adopted May 17, 1989.
    (ii) Other material.
    (A) None.
    (61) Revisions to the Alabama SIP to correct errors and to add 
offset ratios which were submitted on November 10, 1992.
    (i) Incorporation by reference.
    (A) Amendments to the following sections of the Alabama 
regulations--335-3-6-.04(4), 335-3-14-.03(2)(b)15, 335-3-14-.03(2)(b)17, 
335-3-14-.03(2)(b)18, 335-3-14-.03(2)(b)20, 335-3-14-.03(2)(c)2, 335-3-
14-.03(2)(e), 335-3-14-.03(2)(g)1(i), 335-3-14-.03(2)(g)1(ii), and 
Appendix D--were adopted by the State on October 23, 1992.
    (ii) Other material.
    (A) Letter of November 10, 1992, from the Alabama Department of 
Environmental Management.
    (62) The Alabama Department of Environmental Management has 
submitted revisions to chapter 11 of the Alabama Statute on November 13, 
1992. These revision address the requirements of section 507 of Title V 
of the CAA and establish the Small Business Stationary Source Technical 
and Environmental Assistance Program (PROGRAM).
    (i) Incorporation by reference.
    (A) Alabama statute 11.1, effective November 13, 1993.
    (ii) Additional information--None.
    (63) Provisions for coke ovens were submitted by the Alabama 
Department of Environmental Management on September 25, 1985.
    (i) Incorporation by reference.
    (A) Alabama Department of Environmental Management Administrative 
Code, Chapter 335-3-4-.17, Steel Mills Located in Etowah County, adopted 
September 18, 1985.
    (ii) Other material.
    (A) None.
    (64) Revisions to provide synthetic minor operating permit rules 
submitted by the Alabama Department of Environmental Management on 
December 20, 1993.
    (i) Incorporation by reference.
    (A) Alabama Department of Environmental Management Air Division 
Administrative Code, Chapter 335-3-4-.10, -11, -14, -15, and Appendix D, 
adopted November 23, 1993.
    (ii) Other material. None.
    (65) Revisions to the State of Alabama State Implementation Plan 
(SIP) concerning emission statements were submitted on November 13, 
1992, by the Alabama Department of Environmental Management.
    (i) Incorporation by reference. The Addition of Section 11.2 of the 
Alabama Regulations was effective on November 13, 1992.
    (ii) Other material. Letter dated November 13, 1992, from the 
Alabama Department of Environmental Management.
    (66) The Alabama Department of Environmental Management has 
submitted revisions to Alabama SIP on September 28, 1993. These 
revisions address the requirements necessary to change the Leeds area of 
Jefferson County, Alabama, from nonattainment to attainment for lead. 
The submittal includes the maintenance plan for the Leeds Area.
    (i) Incorporation by reference.
    (A) Plan for Maintenance of the NAAQS for Lead in the Jefferson 
County (Leeds) Area after Redesignation to Attainment Status effective 
on September 28, 1993.
    (ii) Additional information. None.
    (67)  [Reserved]
    (68) The State of Alabama submitted a SIP submittal to revise the 
ADEM Administrative Code for the Air Pollution Control Program on August 
14, 1995. These revisions involve changes to Chapter 335-3-14--Air 
Permits.
    (i) Incorporation by reference.
    (1) Amendments to the following sections of the Alabama 
regulations--335-3-14-.04, and 335-3-14-.05 which were adopted on March 
21, 1995.

[[Page 59]]

    (ii) Other material. None.
    (69) The State of Alabama submitted revisions to the ADEM 
Administrative Code for the Air Pollution Control Program on October 30, 
1995, and December 14, 1995. These revisions involve changes to Chapter 
335-3-1--General Provisions.
    (i) Incorporation by reference. Section 335-3-1-.02 (gggg) of the 
Alabama regulations adopted on November 28, 1995.
    (ii) Other material. None.
    (70) The State of Alabama submitted revisions to the ADEM 
Administrative Code for the Air Pollution Control Program on October 30, 
1996. These revisions involve changes to Chapters 335-3-1, -2, -3, -4, -
5, -6, -8, -9, -12, -13, -14, Appendices C, E, and F.
    (i) Incorporation by reference. Chapters 335-3-1-.02(gggg)(23-25); 
335-3-1-.04(1-2); 335-3-1-.06(3); 335-3-1-.08; 335-3-1-.09(11); 335-3-
1-.11; 335-3-2-.02(c); 335-3-2-.08(3); 335-3-3-.01(8); 335-3-4-.01(1)(a-
b), (3); 335-3-4-.04(5); 335-3-4-.07(6-7); 335-3-4-.08(2), (3), (3)(b), 
(4)(b); 335-3-4-.09(1)(4a-b), (4)(c); 335-3-4-.11(2); 335-3-
4-.14(2)(a)2, (2)(b)3; 335-3-4-.15(5-6), (6)(e), (6)(g)1; 335-3-
4-.17(4), (7-9); 335-3-5-.01(2), (2)(b), (4); 335-3-5-.02(1-3); 335-3-
5-.03(4), (4)(b), (5)(b), (8); 335-3-5-.04(10)(d), (12)(b); 335-3-
6-.01(3-6); 335-3-6-.04(4); 335-3-6-.05(3), (4), (5)(a), (5)(f), (6), 
(7); 335-3-6-.06(3)(a), (3)(a)3, (4-5); 335-3-6-.07(1), (2)(d), (3), 
(4), (4)(c), (5)(a), (5)(c), (7); 335-3-6-.11(1)(a), (1)(b-c), (2)(a), 
(2)(b-c), (3), (3)(b-c), (4)(a), (4)(b-d), (5)(a), (5)(b-c), (6)(a), 
(6)(b-c), (7)(a), (7)(b-c), (8)(a-c), (9)(a)3, (9)(b), (10)(a), (10)(b), 
(10)(c-d), (11)(a), (11)(b), (11)(c), (11)(d-e); 335-3-6-.12(4), (5), 
(6), (6)(b)3; 335-3-6-.13(2)(a); 335-3-6-.15(1)(a), (1)(b), (2)(a), 
(2)(c), (3)(a), (3)(b), (4)(a), (4)(c-d), (5); 335-3-6-.16(1)(e)1, 
(1)(e)2I, (2)(g)1, 335-3-6-.49(1), (5)(a); 335-3-6-.50(1); 335-3-
6-.53(13); 335-3-8-.02(1); 335-3-9-.01(3); 335-3-12-.02(2); 335-3-
13-.02(3); 335-3-13.03(3); 335-3-13-.04(3); 335-3-13-.05(3); 335-3-
13-.06(3); 335-3-14-.01(1)(b-c), (1)(e), (1)(g), (1)(k), (1)(k)1-5, 
(6)(a), (6)(b), (6)(b)1, (6)(b)3, (6)(c), (7)(a)2, (7)(c-d); 335-3-
14-.02(1)(a), (4)(b-c), (4)(e)1, (4)(e)4, (5)(a-c); 335-3-14-.03(1)(g)1-
3, (1)(h)2(V), (2)(a), (2)(a)4(V), (2)(a)6(i-ii), (2)(a)7, (2)(a)7(i-
ii), (2)(a)7(I), (2)(a)(7)(II)(iii), (2)(b-c), (2)(f-g); 335-3-
14-.04(2), (2)(a)1(i-iii), (2)(b)1, (2)(c)2(i), (2)(c)4, (2)(c)6(i-ii), 
(2)(f), (2)(i), (2)(i)1, (2)(m)1, (2)(m)1(i), (2)(n)2, (2)(u)1, (2)(u)4, 
(2)(w)3, (6)5(b), (8)(a-d), (8)(e-f), (8)(g-h), (8)(h)3, (8)(k), (8)(l), 
(11)(a), (12)(a)(6-8), (12)(c), (13)(a), (15)(c), (15)(f-h), (17)(c), 
(18)(a), (18)(b)2-3, (18)(c), (18)(d), (19)(a), (19)(c); 335-3-
14-.05(2)(c)1(ii), (2)(l), (3), (3)(c), (4)(c), (4)(c)2, (4)(d), (5-6), 
(6)(c), (7)(a), (9)(c)2, (9)(d), (11), (12)(a), (13)(b)7; 335-3-
15-.01(b), (d-f), (h); 335-3-15-.02(3-4), (7)(c), (8)(f), (8)(h)2, 
(8)(h)4(i), (8)(h)4(iv), (9)(a)4(iv)1-3, (9)(a)4(iv)(V), (9)(a)6(i-ii), 
(9)(a)7, (9)(a)7(i-ii), (9)(a)7(ii)(I), (9)(a)7(iii), (9)(b-c), (9)(f-
g); 335-3-15-.04(1)(a-d), (1)(e), (1)(g-h), (2)(a)(3)(c), (4)(a-b); and 
335-3-15-.05(a) were adopted on October 15, 1996.
    (ii) Other material. None.
    (71) The State of Alabama submitted revisions to the ADEM 
Administrative Code for the Air Pollution Control Program on October 30, 
1996. These revisions involve changes to Chapters 335-3-1, 335-3-3 and 
335-3-6.
    (i) Incorporation by reference. Chapters 335-3-1-.02(gggg)(24-27), 
335-3-3-.01(9) and 335-3-6-.16 except for (5) were adopted on August 19, 
1997.
    (ii) Other material. None.
[37 FR 10846, May 31, 1972]

    Editorial Note: For Federal Register citations affecting Sec. 52.50, 
see the List of CFR Sections Affected in the Finding Aids section of 
this volume.



Sec. 52.51  Classification of regions.

    The Alabama plan was evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                               Pollutant
                                                      ----------------------------------------------------------
              Air quality control region                                                           Photochemical
                                                       Particulate   Sulfur   Nitrogen   Carbon      oxidants
                                                          matter     oxides    dioxide  monoxide  (hydrocarbons)
----------------------------------------------------------------------------------------------------------------
Alabama . Tombigbee Rivers Intrastate................          II        III       III       III           III
Columbus (Georgia)-Phenix City (Alabama) Interstate..           I        III       III       III           III
East Alabama Intrastate..............................           I        III       III       III           III
Metropolitan Birmingham Intrastate...................           I         II       III         I             I

[[Page 60]]

Mobile (Alabama)-Pensacola-Panama City (Florida)-
 Southern Mississippi Interstate.....................           I          I       III       III             I
Southeast Alabama Intrastate.........................          II        III       III       III           III
Tennessee River Valley (Alabama)-Cumberland Mountains
 (Tennessee) Interstate..............................           I          I       III       III           III
----------------------------------------------------------------------------------------------------------------

[37 FR 10847, May 31, 1972]



Sec. 52.53  Approval status.

    With the exceptions set forth in this subpart, the Administrator 
approves Alabama's plans for the attainment and maintenance of the 
national standards under section 110 of the Clean Air Act. Furthermore, 
the Administrator finds the plans satisfy all requirements of Part D, 
Title I, of the Clean Air Act as amended in 1977. In addition, continued 
satisfaction of the requirements of Part D for the ozone portion of the 
SIP depends on the adoption and submittal of RACT requirements by July 
1, 1980 for the sources covered by CTGs issued between January 1978 and 
January 1979 and adoption and submittal by each subsequent January of 
additional RACT requirements for sources covered by CTGs issued by the 
previous January.
[45 FR 37431, June 3, 1980]



Sec. 52.56  Review of new sources and modifications.

    Part D conditional approval. The plan's provisions for review of new 
sources and modifications in nonattainment areas are approved on 
condition that the State submit any necessary corrections by March 9, 
1984 and, during the interim, implement these regulations in a manner 
consistent with EPA requirements.
[48 FR 9860, Mar. 9, 1983]



Sec. 52.57  Control strategy: Sulfur oxides.

    (a) The requirements of Subpart G of this chapter are not met since 
the Alabama plan does not provide for attainment and maintenance of the 
national standards for sulfur oxides in the vicinity of the Widows Creek 
Power Plant in Jackson County, Alabama. Therefore, Part 5.1, Fuel 
Combustion, of Chapter 5, Control of Sulfur Compound Emissions, of the 
rules and regulations of the State of Alabama, as adopted by the Alabama 
Air Pollution Control Commission on May 29, 1973, and amended on March 
25, 1975, which is part of the revised sulfur oxide control strategy, is 
disapproved as it applies to the Widows Creek Plant. Part 5.1 of the 
Alabama rules and regulations as adopted on January 18, 1972, remains 
the implementation plan regulation applicable to that source.
    (b) [Reserved]
[41 FR 42674, Sept. 28, 1976, as amended at 51 FR 40676, Nov. 7, 1986]



Sec. 52.58  Control strategy: Lead.

    The lead plan submitted by the State on March 24, 1982, is 
disapproved because it fails to provide for the attainment of the lead 
standard throughout Alabama. The lead plan submitted by the State on 
October 7, 1985, and November 13, 1986, for Jefferson County is 
conditionally approved on the condition that the State by October 1, 
1987, determine what additional control measures may be necessary, if 
any, to assure attainment and maintenance as expeditiously as 
practicable but no later than the applicable attainment deadline and 
submit those measures to EPA for approval, together with an appropriate 
demonstration of attainment. The provisions in the regulation submitted 
on October 7, 1985, that give the Jefferson County Health Officer 
discretion to vary the requirements of the regulation are approved as 
limits on that discretion, but any variances that may result from those 
provisions are not approved in advance and hence change the applicable 
implementation

[[Page 61]]

plan only when approved by EPA on a case-by-case basis.
[49 FR 18738, May 2, 1984, as amended at 52 FR 4291, Feb. 11, 1987]



Sec. 52.60  Significant deterioration of air quality.

    (a) All applications and other information required pursuant to 
Sec. 52.21 from sources located in the State of Alabama shall be 
submitted to the Division of Air Pollution Control, Alabama Air 
Pollution Control Commission, 645 South McDonough Street, Montgomery, 
Alabama 36103, rather than to EPA's Region IV Office.
    (b) On March 24, 1987, the Alabama Department of Environmental 
Management submitted a letter committing the State of Alabama to require 
that modeling for PSD permits be done only in accordance with the 
``Guideline on Air Quality Models (Revised)'' or other models approved 
by EPA.
[42 FR 22869, May 5, 1977, as amended at 46 FR 55518, Nov. 10, 1981; 52 
FR 48812, Dec. 28, 1987]



Sec. 52.61  Visibility protection.

    (a) The requirements of section 169A of the Clean Air Act are not 
met because the plan does not include approvable procedures for 
protection of visibility in mandatory Class I Federal areas.
    (b) Long-term strategy. The provisions of Sec. 52.29 are hereby 
incorporated into the applicable plan for the State of Alabama.
[52 FR 45138, Nov. 24, 1987]



Sec. 52.62  Control strategy: Sulfur oxides and particulate matter.

    In a letter dated May 29, 1987, the Alabama Department of Health and 
Environmental Control certified that no emission limits in the State's 
plan are based on dispersion techniques not permitted by EPA's stack 
height rules. The certification does not apply to: Alabama Electric 
Cooperative--Lowman Steam Plant; Alabama Power Company-Gorgas Steam 
Plant, Gaston Steam Plant, Greene County Steam Plant, Gadsden Steam 
Plant, Miller Steam Plant, and Barry Steam Plant; Alabama River Pulp; 
Champion International Corporation; Container Corporation of America; 
Exxon Company's Big Escambia Creek Treating Facility; General Electric's 
Burkville Plant; International Paper; Scott Paper Company; Tennessee 
Valley Authority's Colbert, and Widows Creek Steam Plant; Union Camp 
Corporation; and U.S. Steel.
[55 FR 5846, Feb. 20, 1990]



Sec. 52.63  PM10 State Implementation Plan development in group II areas.

    On March 15, 1989, the State submitted a committal SIP for the 
cities of Leeds and North Birmingham in Jefferson County. The committal 
SIP contains all the requirements identified in the July 1, 1987, 
promulgation of the SIP requirements for PM10 at 52 FR 24681. 
The SIP commits the State to submit an emissions inventory, continue to 
monitor for PM10, report data and to submit a full SIP if a 
violation of the PM10 and National Ambient Air Quality 
Standards is detected.
[56 FR 32514, July 17, 1991]



Sec. 52.64  [Reserved]



Sec. 52.65  Control Strategy: Nitrogen oxides.

    On October 22, 1990, the Alabama Department of Environmental 
Management submitted a revision to Chapter 2, Control Strategy, by 
adding subsection 4.2.3. This revision addressed the strategy Alabama is 
using to implement provisions of the Prevention of Significant 
Deterioration regulations for nitrogen oxides.
[57 FR 24370, June 9, 1992]



Sec. 52.66  Control Strategy: Ozone.

    The redesignation request submitted by the State of Alabama, on 
March 16, 1995 for the Birmingham marginal ozone nonattainment area from 
nonattainment to attainment was disapproved on September 19, 1997.
[62 FR 49158, Sept. 19, 1997]



                            Subpart C--Alaska



Sec. 52.70  Identification of plan.

    (a) Title of plan: ``State of Alaska Air Quality Control Plan.''

[[Page 62]]

    (b) The plan was officially submitted on April 25, 1972.
    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) Modifications to the implementation plan including a revision to 
Title 18, Chapter 50, section 160 and other nonregulatory provisions 
submitted on June 22, 1972, by the Governor.
    (2) Compliance schedules submitted on August 2, 1973, by the State 
of Alaska Department of Environmental Conservation.
    (3) Compliance schedules submitted on August 23, 1973, by the State 
of Alaska Department of Environmental Conservation.
    (4) Compliance schedules submitted on September 30, 1975, by the 
State of Alaska Department of Environmental Conservation.
    (5) Compliance schedules submitted on January 6, 1976, by the State 
of Alaska Department of Environmental Conservation.
    (6) Compliance schedules submitted on September 30, 1975, by the 
State of Alaska Department of Environmental Conservation.
    (7) Part D attainment plans for the Anchorage and Fairbanks carbon 
monoxide nonattainment areas submitted by the Governor of Alaska on 
January 18, 1980 as follows:

            Volume II. Analysis of Problems, Control Actions

Section III. Areawide Pollutant Control Efforts, Subsection A.
Carbon Monoxide, except subparts 1.c (Other areas) and 5.h (Fairbanks 
          Emergency Avoidance Plan)

                         Volume III. Appendices

III-1 A Review of Carbon Monoxide Emissions from Motor Vehicles during 
          Cold Temperature Operation
III-2 Cold Weather Related Strategy Support Development
III-3 Preliminary Assessment of Meteorological Conditions during Days of 
          Ambient Air Quality Violations in Anchorage
III-4 Summary of the 1978 Fairbanks Voluntary Vehicle Emissions 
          Inspection Program
III-5 Approach of Evaluating an Alaska I/M Program
III-6 Appendices to the Anchorage Air Quality Plan
III-7 Appendices to the Fairbanks Air Quality Plan

    (8) On January 18, 1980, the State of Alaska Department of 
Environmental Conservation submitted a plan revision to meet the 
requirements of Air Quality Monitoring, 40 CFR part 58, subpart C, 
Sec. 58.20, as follows:

            Volume II. Analysis of Problems, Control Actions

Section V. Ambient Air Monitoring
    A. Purpose
    C. Air Monitoring Network
    E. Annual Review

    (9) Provisions of a State Air Quality Control Plan submitted by the 
Governor of Alaska on January 18, 1980, as follows:

            Volume II. Analysis of Problems, Control Actions

Section I. Introduction
    A. Summary
    B. Air Quality Control Regions
    C. Attainment/Nonattainment Designations
Section II. Alaskan Air Quality Control Programs
    A. State Program
    B. Local Programs
    C. Resource Needs
Section III. Areawide Pollutant Control Efforts
    A. Carbon Monoxide, Subpart 1.c (Other areas)
    B. Total Suspended Particulate Matter
    C. Ice Fog
    D. Open Burning--Forest Practices
Section IV. Point Source Control Efforts
    A. Summary
    B. Description of Source Categories and Pollutants
    C. Summary of Major Emitting Sources
    D. History of Alaskan Point Source Program
    F. Local Program Enforcement
    G. New Source Review and Approval
    H. Compliance Assurance
    I. State Air Quality Control Regulations
Section V. Ambient Air Monitoring
    B. Description of Previous Air Monitoring Network

                         Volume III. Appendices

I-1 Summary of Public Hearings, Written Testimony, etc.
I-2 Recommendations for attainment/Nonattainment designations
II-1 Alaska Statutes, except section 46.03.170
II-2 Regulations of the Fairbanks North Star Borough, except section 
          8.04.070
II-3 Fairbanks North Star Borough/Alaska Department of Environmental 
          Conservation Agreement
II-4 Municipality of Anchorage/Alaska Department of Environmental 
          Conservation Agreement

[[Page 63]]

II-5 Alaska State Department of Law Legal Opinion
IV-1 Summaries of Emission Inventories
IV-2 D. Permit to Operate for the Fairbanks Municipal Utilities System
IV-3 Testing Procedures
V-1 Air Quality Data
An amended Appendix II-5, ``Alaska State Department of Law Legal 
Opinion'' submitted by the State of Alaska Department of Environmental 
Conservation on February 29, 1980. Amendments to the January 18, 1980 
submittal, submitted by the State of Alaska Department of Environmental 
Conservation on September 29, 1982 as follows:

            Volume II. Analysis of Problems, Control Actions

Section I. Introduction
    C. Attainment/Nonattainment Designations
Section III. Areawide Pollutant Control Efforts
    D. Open Burning--Forest Practices
Section IV. Point Source Control Efforts
    C. Summary of Major Emitting Sources
    D. History of Alaskan Point Source Program
    F. Local Program Enforcement
    G. New Source Review and Approval
    H. Compliance Assurance
    I. State Air Quality Control Regulations
Section V. Ambient Air Monitoring
    C. Air Monitoring Network
    E. Annual Review

                         Volume III. Appendices

IV-4 ADEC Ambient Analysis Procedures

    (10) On November 15, 1983 the State of Alaska Department of 
Environmental Conservation submitted a revision to add a lead strategy 
to the Alaska Implementation Plan.
    (11) Provisions of a State Air Quality Control Plan submitted by the 
Alaska Department of Environmental Conservation on November 15, 1983, as 
follows:

            VOLUME II. ANALYSIS OF PROBLEMS, CONTROL ACTIONS

                          Section I. BACKGROUND

A. INTRODUCTION
B. AIR QUALITY CONTROL REGIONS
C. ATTAINMENT/NONATTAINMENT DESIGNATIONS
D. PREVENTION OF SIGNIFICANT DETERIORATION DESIGNATIONS

              Section II. STATE AIR QUALITY CONTROL PROGRAM

             Section III. AREAWIDE POLLUTANT CONTROL PROGRAM

D. TOTAL SUSPENDED PARTICULATE MATTER
E. ICE FOG
F. OPEN BURNING
G. WOOD SMOKE POLLUTION CONTROL

                Section IV. POINT SOURCE CONTROL PROGRAM

A. SUMMARY
    1. Annual Review Report
B. STATE AIR QUALITY REGULATIONS
C. LOCAL PROGRAMS
D. DESCRIPTION OF SOURCE CATEGORIES AND POLLUTANTS
    1. Typical Point Sources
    2. Summary of Major Emitting Facilities
E. POINT SOURCE CONTROL
    1. Introduction
F. FACILITY REVIEW PROCEDURES
    1. Who needs a permit?
    2. Standard Application Procedures
    3. PSD Application Procedures, Preliminary report and meeting, Pre-
construction monitoring, PSD application format
    4. Nonattainment Application Procedures
G. APPLICATION REVIEW AND PERMIT DEVELOPMENT
    1. Application Review
    2. Permit Development Requirement, Monitoring and Testing 
Requirements, Ambient Monitoring, Continuous Emissions Monitoring, 
Source Testing
    3. Prevention of Significant Deterioration Review, Basis of Program, 
PSD Regulations, PSD Analysis Procedure
    4. Nonattainment Area Review
    5. New Source Performance Standards Source Review
    6. Visibility Review
    7. Sources under EPA Review
H. PERMIT ISSUANCE REQUIREMENTS

                    Section V. AMBIENT AIR MONITORING

A. PURPOSE
B. COMPLETED AIR MONITORING PROJECTS
    1. Carbon Monoxide
    2. Nitrogen Oxides
    3. Sulfur Dioxide
    4. Ozone
    5. Total Suspended Particulates (TSP)
    6. Lead
C. AIR MONITORING NETWORK
    1. Network Description
    2. Station Designations
    3. Air Quality Monitoring Procedures
    4. Ambient Sampling for Specific Pollutants
E. ANNUAL REVIEW

[[Page 64]]

                         VOLUME III. APPENDICES

              Section II. STATE AIR QUALITY CONTROL PROGRAM

II.A. State Air Statutes, except section 46.03.170, State Attorney 
          General Opinions on Legal Authority
II.B. Municipality of Anchorage/Cook Inlet/ADEC Agreements
II.C. Fairbanks North Star Borough Ordinances/FNSB & ADEC Agreements

             Section III. AREAWIDE POLLUTANT CONTROL PROGRAM

III.G. Ordinance of the City and Borough of Juneau

                Section IV. POINT SOURCE CONTROL PROGRAM

IV.1. PSD Area Classification and Reclassifications
    A. Class I Area Boundaries
    B. Areas Protected from Visibility Degradation
    C. Reclassification
    1. Limitations on PSD Reclassification
    2. PSD Reclassification Procedures
IV.2. Compliance Assurance
IV.3. Testing Procedures

                    Section V. AMBIENT AIR MONITORING

    ADEC Ambient Analysis Procedures

TITLE 18. ENVIRONMENTAL CONSERVATION, CHAPTER 50. AIR QUALITY CONTROL, 
Sections 021(d), 030(g), 040(a)(2), 040(c), 050(a)(2), 050(b)(4), 085, 
300(a)(1), 300(a)(7), 400(d)(6), 500(d), 500(e), 510 (Editor's Note), 
520(a), 520(b), 610(a), 620, 900(15), 900(39), 900(47), and 900(48).

    (12) On September 29, 1982, the Commissioner of the Alaska 
Department of Environmental Conservation submitted a carbon monoxide 
attainment plan for the cities of Anchorage (section III.B) and 
Fairbanks (section III.C) as a revision to the Alaska State 
Implementation Plan. On November 15, 1983, a revision to this plan was 
submitted for the city of Anchorage. Supplement to the Anchorage and 
Fairbanks plans revisions to section III.A (Areawide Pollutant Control 
Program, Statewide Transportation Control Program) and a new State 
Regulation 18 AAC Chapter 52 (Emissions Inspection and Maintenance 
Requirements for Motor Vehicles) were submitted on May 31, 1985.
    (i) Incorporation by reference.
    (A) May 31, 1985 letter from the State of Alaska to EPA, and State 
Regulation 18 AAC 52 (Emissions Inspection and Maintenance Requirements 
for Motor Vehicles) as filed by the Commissioner for the State of Alaska 
on May 19, 1985.
    (B) Page section III.B.8-3 of the Anchorage Transportation Control 
Program, Alaska Air Quality Control Plan, revised June 1, 1985 
(emissions and air quality projections for Anchorage with vehicle 
inspection and maintenance program).
    (C) Table C.6.a of the Fairbanks Transportation Control Program, 
Alaska Air Quality Control Plan [reasonable further progress required 
reductions for Fairbanks] (page section III.C.6-2) revised November 20, 
1982.
    (ii) Other material.
    (A) Section III.A Statewide Transportation Control Program.
    (B) Section III.B Anchorage Transportation Control Program.
    (C) Section III.C Fairbanks Transportation Control Program.
    (D) The I/M Program Design for the Fairbanks North Star Borough 
dated October 25, 1984.
    (E) The I/M Program Design for the Municipality of Anchorage dated 
1984.
    (13) On June 26, 1987, the State of Alaska Department of 
Environmental Conservation submitted Section III.B.10-1 through 
III.B.10-6 (Anchorage Air Pollution Episode Curtailment Actions); 
Section III.C.10-1 through III.C.10-9 (Fairbanks Emergency Episode 
Prevention Plan); and minor modifications to Section III.C.5-7 
(Fairbanks Inspection and Maintenance Program Design).
    (i) Incorporation by Reference.
    (A) June 26, 1987 letter from the State of Alaska Department of 
Environmental Conservation to EPA Region 10.
    (B) Section III.B.10-1 through III.B.10-6 of Volume II (Anchorage 
Air Pollution Episode Curtailment Actions) as adopted as an ordinance by 
the Anchorage Assembly on September 9, 1986.
    (C) Section III.C.10-1 through III.C.10-9 of Volume II (Fairbanks 
Emergency Episode Prevention Plan) as adopted as an ordinance by the 
Assembly of the Fairbanks North Star Borough on December 19, 1985.
    (D) Page number Section III.C.5-7 of Volume II (Fairbanks Inspection 
and Maintenance Design). This new page

[[Page 65]]

supercedes the current page number Section III.C.5-7 of the Alaska Air 
Quality Control Plan as adopted by the Alaska Department of 
Environmental Conservation on June 26, 1987.
    (14) On June 26, 1987, the Commissioner of the Alaska Department of 
Environmental Conservation submitted revised rules regulating the height 
of stacks and the use of dispersion techniques, specifically revisions 
to 18 AAC 50.400(a), 18 AAC 50.530(c), 18 AAC 50.900(16), 18 AAC 
50.900(20), 18 AAC 50.900(23), and 18 AAC 50.900.(29), and the deletion 
of 18 AAC 50.900(17).
    (i) Incorporation by Reference.
    (A) June 26, 1987 letter from the State of Alaska Department of 
Environmental Conservation to EPA, Region 10.
    (B) August 11, 1987 letter from the State of Alaska Department of 
Environmental Conservation to EPA, Region 10.
    (C) 18 AAC 50.400(a) and 18 AAC 50.900 (16), (20), (23), and (29) as 
adopted by the State of Alaska Department of Environmental Conservation 
on December 31, 1986.
    (15) On September 12, 1988, the State of Alaska Department of 
Environmental Conservation submitted revisions to AAC 18 Chapter 52 
(Emission Inspection and Maintenance Requirements for Motor Vehicles). 
Those sections amended through June 2, 1988, are: 18 AAC 51.010 [Purpose 
and General Requirements] (a)(3), (b), (d), (e), and (g); 18 AAC 52.020 
[Vehicles Subject to this Chapter] (1); 18 AAC 52.070 [Waivers] (5)(A) 
through (C); and 18 AAC 52.900 [Definitions] (14).
    (i) Incorporation By Reference.
    (A) September 12, 1988 letter from the State of Alaska Department of 
Environmental Conservation to EPA Region 10.
    (B) Chapter 52 [Emissions Inspection and Maintenance Requirements 
for Motor Vehicles] section 52.010 [Purpose and General Requirements 
(a)(3), (b), (d), (e), and (g); section 52.020 [Vehicles Subject to This 
Chapter] (1); section 52.070 [Waivers] (5)(A) through (C); and section 
52.900 [Definitions] (14) as adopted by the State of Alaska Department 
of Environmental Conservation on March 10, 1988.
    (16) On September 12, 1988, the State of Alaska Department of 
Environmental Conservation submitted revisions to the State of Alaska 
state implementation plan. Specifically pages IV.F.1-1 through IV.F.1-8 
of section IV.F ``Project Review Procedures'' and amendments to title 
18, chapter 50, sections 050(a)(4), 050(b), 050(d)(1), 300(a)(5)(C), 
300(a)(6)(C), 300(a)(7), 300(c), 300(g), 500(d), 510(a), 520(a), 520(b), 
and 620 of the Alaska Administrative Code.
    (i) Incorporation By Reference. (A) September 12, 1988, letter from 
the State of Alaska Department of Environmental Conservation to EPA 
Region 10 submitting a revision to the Alaska state implementation plan.
    (B) Vol. II, Analysis of Problems, Control Actions, Pages IV.F.1-1 
through IV.F.1-8 of section IV.F, ``Project Review Procedures,'' revised 
June 2, 1988.
    (C) Title 18, chapter 50, (Air Quality Control) section 050 
(Industrial Processes and Fuel Burning Equipment) (a)(4), 050(b), 
050(d)(1), 300 (Permit to Operate) (a)(5)(C), 300(a)(6)(C), 300(a)(7), 
300(c), 300(g), 500 (Source Testing) (d), 510 (Ambient Analysis Methods) 
(a), 520 (Emission and Ambient Monitoring) 520(a), 520(b), and 620 (Air 
Quality Control Plan) of the Alaska Administrative Code as adopted by 
the State of Alaska Department of Environmental Conservation on March 
10, 1988 and effective on June 2, 1988.
    (17) On October 17, 1991, the State of Alaska Department of 
Environmental Conservation submitted a PM10 nonattainment 
area state implementation plan for Eagle River, Alaska.
    (i) Incorporation by reference.
    (A) October 15, 1991 letter from Alaska Department of Environmental 
Conservation to EPA Region 10 submitting the PM10 
nonattainment area state implementation plan for Eagle River, Alaska.
    (B) The PM10 nonattainment area state implementation plan 
for Eagle River, Alaska, as adopted by the Anchorage Assembly on 
February 6, 1990 and effective on September 24, 1991.
    (18) On June 22, 1993, the Governor of the State of Alaska submitted 
revised rules to satisfy certain Federal Clean Air Act requirements for 
an approvable moderate PM10 nonattainment area

[[Page 66]]

SIP for Mendenhall Valley, Alaska. Also included in this SIP were 
PM10 contingency measures for the Mendenhall Valley. On 
January 21, 1992, a supplement to the existing Eagle River 
PM10 control plan was submitted by ADEC to EPA and certified 
on March 8, 1993, by the Lieutenant Governor of Alaska.
    (i) Incorporation by reference.
    (A) June 22, 1993, letter from the Governor of the State of Alaska 
to EPA, Region 10, submitting the moderate PM10 nonattainment 
area SIP for Mendenhall Valley, Alaska.
    (B) The Control Plan for Mendenhall Valley of Juneau, effective July 
8, 1993.
    (C) August 25, 1993, letter from ADEC showing, through enclosures, 
the permanent filing record for the supplement to the existing Eagle 
River PM10 control plan. The Lieutenant Governor certified 
the supplement on March 8, 1993.
    (D) The January 21, 1992, supplement to the existing Eagle River 
PM10 control plan, effective April 7, 1993. Also included is 
an August 27, 1991 Municipality of Anchorage memorandum listing the 1991 
capital improvement project priorities and an October 11, 1991, 
Muncipality of Anchorage memorandum summarizing the supplement to the 
existing PM10 control plan.
    (19) The Environmental Protection Agency (EPA) takes action on and/
or approves regulations from three submittals received from the ADEC on 
July 17, 1990, October 15, 1991 and on March 24, 1994, which pertain to 
correcting SIP deficiencies in the CFR; amendments to regulations 
dealing with Air Quality Control, 18 AAC 50, for inclusion into Alaska's 
SIP; and additional amendments to 18 AAC 50, Air Quality Control, for 
inclusion into Alaska's SIP to assure compliance with new source review 
permitting requirements for sources located in nonattainment areas for 
either carbon monoxide or particulate matter.
    (i) Incorporation by reference.
    (A) July 17, 1990 letter from ADEC to EPA requesting correction for 
findings of SIP deficiency in 40 CFR Part 52, and including the version 
of Alaska Statutes, ``Title 46. Water, Air, Energy, and Environmental 
Conservation,'' in effect at the time of the July 17, 1990 letter, of 
which Sections 46.03.020, 46.03.030, 46.03.032, and 46.03.715, amended 
in 1987, were the most recently amended of the enclosed statutes.
    (B) October 15, 1991 letter from ADEC to EPA, and including 
amendments to regulations and the State Air Quality Control Plan to 
assure compliance with national ambient air quality standards for 
particulate matter; the Order Amending Regulations of the Department of 
Environmental Conservation, effective July 21, 1991; and the following 
Alaska Administrative Code, 18 AAC 50, Air Quality Control Regulations: 
(50.020; 50.085; 50.100; 50.300; 50.400; 50.510, 50.520, 50.610, and 
50.900), effective July 21, 1991, Register 119.
    (C) March 24, 1994 letter from Walter J. Hickel, Governor of Alaska, 
to Chuck Clarke, Regional Administrator of EPA, and including amendments 
to 18 AAC 50, State Air Quality Control Plan; the Order Adopting and 
Amending Regulations of the Department of Environmental Conservation, 
effective April 23, 1994, Register 130; and the amendments to 18 AAC 50 
(50.021, 50.300(a)(7) and (a)(8), 50.300 (d), (e), and (g), 
50.400(a)(1)(A), 50.400(c)(3)(B)(ii), 50.400(c)(4), 50.400(d)(4), and 
50.620), State Air Quality Control Plan, found in Volume III: 
Appendices, Modifications to Section III.A, effective April 23, 1994, 
Register 130.
    (20) On April 18, 1994, the Commissioner of the Alaska Department of 
Environmental Conservation (ADEC) submitted ``The Alaska Air Quality 
Small Business Assistance Program State Air Quality Control Plan 
Amendment,'' adopted April 8, 1994, as a revision to the Alaska SIP.
    (i) Incorporation by reference.
    (A) Letter dated April 8, 1994, from the Commissioner of ADEC to the 
Regional Administrator of EPA, submitting ``The Alaska Air Quality Small 
Business Assistance Program State Air Quality Control Plan Amendment'' 
to EPA; the Alaska Air Quality Small Business Assistance Program State 
Air Quality Control Plan Amendment (which includes Appendix A the Alaska 
Statutes Title 46, Chapter 14, Article 3), dated April 1994, and adopted 
April 8, 1994.
    (ii) Additional information.

[[Page 67]]

    (A) Letter dated July 24, 1995, from Alaska Department of 
Environmental Conservation, submitting information necessary for 
approval of the SBAP revision to EPA; the July 1995 SBAP Update, 
Responses to EPA Comments, and the Air Quality/Small Business Assistance 
Compliance Advisory Panel Board Information.
    (21) On July 11, 1994 ADEC submitted a SIP revision for a basic 
motor vehicle inspection and maintenance (I/M) program in the 
Municipality of Anchorage (MOA) and the Fairbanks North Star Borough 
(FNSB).
    (i) Incorporation by reference.
    (A) July 11, 1994 letter from the Governor of Alaska to the Regional 
Administrator of EPA submitting Alaska's amendments to the Air Quality 
Control Plan and to 18 AAC 52, Emissions Inspection and Maintenance 
Requirements for Motor Vehicles; the amendments to 18 AAC 52 (52.005, 
.015, .020, .030, .035, .040, .045, .050, .055, .060, .065, .070, .075, 
.080, .085, .090, .095, .100, .105, .400, .405, .410, .415, .420, .425, 
.430, .440, .445, .500, .505, .510, .515, .520, .525, .527, .530, .535, 
.540, .545, .550, and .990), effective February 1, 1994; and the State 
Air Quality Control Plan, Vol. II: Analysis of Problems, Control 
Actions, Modifications to Section I, June 9, 1994; Vol. II: Analysis of 
Problems, Control Actions, Modifications to Section I, II, III and V, 
adopted January 10, 1994; Vol. III: Appendices, Modifications to Section 
III.A, June 9, 1994; Vol. III: Appendices, Modifications to Section 
III.B, June 9, 1994; and Vol. III: Appendices, Modifications to Section 
III.C, June 9, 1994.
    (22) On March 24, 1994, ADEC submitted a revision to its SIP for the 
State of Alaska addressing the attainment and maintenance of the 
National Ambient Air Quality Standards for carbon monoxide in the 
Anchorage carbon monoxide nonattainment area.
    (i) Incorporation by reference.
    (A) March 24, 1994 letter from Alaska Governor Walter Hickel to EPA 
Regional Administrator Chuck Clarke including as a revision to the SIP 
the State of Alaska, Department of Environmental Conservation, 18 AAC 
53, ``Fuel Requirements for Motor Vehicles,'' (Article 1, 18 AAC 
53.005--18 AAC 53.190 and Article 9, 18 AAC 53.990) with amendments 
adopted through March 19, 1994.
    (23) On March 24, 1994, ADEC submitted a SIP revision to EPA to 
satisfy the requirements of sections 187(a)(2)(A) and 187(a)(3) of the 
CAA, forecasting and tracking VMT in the Anchorage area.
    (i) Incorporation by reference.
    (A) March 24, 1994 letter from the Alaska Governor to the EPA 
Regional Administrator including as a revision to the SIP the VMT 
requirement in the Anchorage area, contained in ADEC's State Air Quality 
Control Plan, Volume III: Appendices, Modifications to Section III.B.6, 
III.B.8, III.B.10 and III.B.11, adopted January 10, 1994; and further 
description on pages 10-14, 57-60 and 69-75 contained in ADEC's State 
Air Quality Control Plan, Volume III: Appendices, Modifications to 
Section III.B, III.B.1, and III.B.3, adopted January 10, 1994.
    (24) On December 5, 1994 the Alaska Department of Environmental 
Conservation sent EPA revisions for inclusion into Alaska's SIP that 
address transportation and general conformity regulations as required by 
EPA under the CAA.
    (i) Incorporation by reference.
    (A) December 5, 1994 letter from the Governor of Alaska to EPA, 
Region 10, submitting amendments addressing transportation and general 
conformity revisions to the SIP:
    (1) Regulations to 18 AAC 50, Air Quality Control, including Article 
5, Procedure and Administration, 18 AAC 620; Article 6, Reserved; 
Article 7, Conformity, 18 AAC 50.700-18 AAC 50.735; Article 8, Reserved; 
and Article 9, General Provisions, 18 AAC 50.900, all of which contain 
final edits (23 pages total) by the Alaska Department of Law, were filed 
by the Lieutenant Governor on December 5, 1994 and effective on January 
4, 1995.
    (2) Amendments to the Alaska State Air Quality Control Plan, 
``Volume II: Analysis of Problems, Control Actions,'' as revised on 
December 1, 1994, adopted by reference in 18 AAC 50.620, containing 
final edits by the Alaska Department of Law, all of which were certified 
by the Commissioner of Alaska to be the correct plan amendments,

[[Page 68]]

filed by the Alaska Lieutenant Governor on December 5, 1994 and 
effective on January 4, 1995.
    (25) On March 24, 1994, ADEC submitted a revision to its SIP for the 
State of Alaska addressing the attainment and maintenance of the NAAQS 
for CO in the Anchorage CO nonattainment area.
    (i) Incorporation by reference.
    (A) March 24, 1994 letter from the Alaska Governor to the EPA 
Regional Administrator including as a revision to the SIP the State of 
Alaska, Department of Environmental Conservation, 18 AAC 53, ``Fuel 
Requirements for Motor Vehicles,'' (Article 1, 18 AAC 53.005--18 AAC 
53.190 and Article 9, 18 AAC 53.990, with the exception of 18 AAC 
53.010(c)(2)), filed March 24, 1994 and effective on April 23, 1994.
    (26) Submittal to EPA from the ADEC of CO contingency measure for 
Fairbanks, AK.
    (i) Incorporation by reference.
    (A) Letter dated July 12, 1995 from the Commissioner of the ADEC to 
the EPA Regional Administrator submitting its repair technician and 
certification program element found in State regulation 18 AAC 52.400-
410, effective June 24, 1994.
    (27) On October 31, 1997, ADEC submitted revisions to Fuel 
Requirements for Motor Vehicles, title 18, chapter 53 of the Alaska 
Administrative Code (18 AAC 53) regarding the use of oxygenated fuels.
    (i) Incorporation by reference.
    (A) Title 18, Chapter 53, Alaska Administrative Code (AAC), Fuel 
Requirements for Motor Vehicles, adopted October 31, 1997 (Article 1, 18 
AAC 53 .005, .007, .010, .015, .020, .030, .035, .040, .045, .060, .070, 
.080, .090, .100, .105, .120, .130, .140, .150, .160, .170, .190; 
Article 9, 18 AAC 53.990).
[37 FR 10848, May 31, 1972]

    Editorial Note: For Federal Register citations affecting Sec. 52.70, 
see the List of CFR Sections Affected in the Finding Aids section of 
this volume.



Sec. 52.71  Classification of regions.

    The Alaska plan was evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                                  Pollutant
                                                           -----------------------------------------------------
                Air quality control Region                  Particulate   Sulfur   Nitrogen   Carbon
                                                               matter     oxides    dioxide  monoxide    Ozone
----------------------------------------------------------------------------------------------------------------
Cook Inlet Intrastate.....................................           I        III       III         I       III.
Northern Alaska Intrastate................................           I        III       III         I       III.
South Central Alaska Intrastate...........................         III        III       III       III       III.
Southeastern Alaska Intrastate............................         III        III       III       III       III.
----------------------------------------------------------------------------------------------------------------

[37 FR 10848, May 31, 1972, as amended at 48 FR 30625, July 5, 1983]



Sec. 52.72  Approval status.

    With the exceptions set forth in this subpart, the Administrator 
approves Alaska's plan for the attainment and maintenance of the 
national standards. The State included in the plan a regulation 
prohibiting idling of unattended motor vehicles. However, the plan 
stated that this regulation was included for informational purposes 
only, and was not to be considered part of the control strategy to 
implement the national standards for carbon monoxide. Accordingly, this 
regulation is not considered a partof the applicable plan.
[37 FR 15080, July 27, 1972]



Secs. 52.73--52.74  [Reserved]



Sec. 52.75  Contents of the approved state-submitted implementation plan.

    The following sections of the State Air Quality Control Plan (as 
amended on the dates indicated) have been approved and are part of the 
current State Implementation Plan:

             Volume II: Analysis of Problems, Control Action

                          Section I Background

A. Introduction (7/1/82)
B. Air Quality Control Regions (7/1/82)
C. Attainment/ Nonattainment Designations (7/1/83)

[[Page 69]]

         Section II State Air Quality Control Program (11/1/83)

             Section III Areawide Pollutant Control Program

A. Statewide Transportation Control Program (6/1/85)
B. Anchorage Transportation Control Program (6/1/85), except B.10.1 
          through 10.6 Anchorage Air Pollution Curtailment Actions (6/
          26/87)
C. Fairbanks Transportation Control Program (6/1/85), except C.10.1 
          through 10.9 Fairbanks Emergency Episode Prevention Plan (6/
          26/87)
D. Total Suspended Particulate Matter (7/1/82)
E. Ice Fog (7/1/82)
F. Open Burning (10/30/83)
G. Wood Smoke Pollution Control (7/1/83)
H. Lead Pollution Control (7/1/83)

                 Section IV Point Source Control Program

A. Summary (10/30/83)
    1. Annual Review Report (10/30/83)
B. State Air Quality Regulations (10/30/83)
C. Local Programs (10/30/83)
D. Description of Source Categories And Pollutants
    1. Typical Point Sources (10/30/83)
    2. Summary of Major Emitting Facilities (10/30/83)
E. Point Source Control 1. Introduction (10/30/83)
F. Facility Review Procedures
    1. Project Review Procedures (6/02/88) Who needs a permit? (10/30/
83, 6/02/88)
    2. Standard Application Procedures (10/30/83)
    3. PSD Application Procedures (10/30/83)
    Preliminary report and meeting (10/30/83)
    Pre-construction monitoring (10/30/83) PSD application format (10/
30/83)
    4. Nonattainment Application Procedures (10/30/83)
G. Application Review and Permit Development (10/30/83)
    1. Application Review (10/30/83)
    2. Permit Development Requirements (10/30/83)
    Monitoring and Testing Requirements (10/30/83)
    Ambient Monitoring (10/30/83)
    Continuous Emissions Monitoring (10/30/83)
    Source Testing (10/30/83)
    3. Prevention of Significant Deterioration Review (10/30/83)
    Basis of Program (10/30/83)
    PSD Regulations (10/30/83)
    PSD Analysis (10/30/83)
    4. Nonattainment Area Review (10/30/83)
    5. New Source Performance Standards Source Review (10/30/83)
    6. Visibility Review (10/30/83)
    7. Sources under EPA Review (10/30/83)
H. Permit Issuance Requirements (10/30/83)

                    Section V Ambient Air Monitoring

A. Purpose (7/1/82)
B. Completed Air Monitoring Projects (7/1/82)
    1. Carbon Monoxide (7/1/82)
    2. Nitrogen Oxides (7/1/82)
    3. Sulfur Dioxide (7/1/82)
    4. Ozone (7/1/82)
    5. Total Suspended Particulates (TSP) (7/1/82)
    6. Lead (7/1/82)
C. Air Monitoring Network (7/1/82)
    1. Network Description (7/1/82)
    2. Station Designations (7/1/82)
    3. Air Quality Monitoring Procedures (7/1/82)
    4. Ambient Sampling for Specific Pollutants (7/1/82)
E. Annual Review (7/1/82)

                         Volume III. Appendices

              Section II State Air Quality Control Program

II.A. State Air Statues, except Section 46.03.170 (11/15/83)
    State Attorney General Opinions on Legal Authority--(2/29/72, 2/29/
80)
Title 18--Environmental Conservation, Chapter 50--Air Quality Control 
          (10/30/83), (6/7/87), (6/2/88)
Title 18--Environmental Conservation, Chapter 52--Emissions Inspections 
          and Maintenance Requirements for Motor Vehicles (5/19/85), 
          except
    18 AAC 52.010 (3), (3b), (3d), (3e), and (3g) (5/19/85)
    18 AAC 52.020 (1) (5/19/85)
    18 AAC 52.070 (5) (A)-(C) (5/19/85)
    18 AAC 52.900 (14) (5/19/85)
II.B. Municipality of Anchorage/Cook Inlet ADEC Agreements (11/15/83)
II.C. Fairbanks North Star Borough Ordinances, except Section 8.04.070/
          FNSB & ADEC Agreements (11/15/83)

             Section III Areawide Pollutant Control Program

III.B.3-a Anchorage Graphs of Highest and Second Highest CO readings for 
          Each Site (11/15/83)
III.B.5-a Anchorage Traffic Improvements (11/15/83)
III.B.5-b Anchorage Contingency Plan (11/15/83)
III.B.5-c Anchorage Transit Ridership (11/15/83)
III.B.8-a Anchorage Graphs of Projected CO Concentrations for Each Site 
          (11/15/83)
III.G Ordinance of the City and Borough of Juneau (10/6/83)
III.H Support Documents for Lead Plan (11/15/83)

                 Section IV Point Source Control Program

IV.1 PSD Area Classification and Reclassifications (11/15/83)
    A. Class I Area Boundaries (11/15/83)

[[Page 70]]

    B. Areas Protected from Visibility Degradation (11/15/83)
    C. Reclassification (11/15/83)
    1. Limitations on PSD Reclassification (11/15/83)
    2. PSD Reclassification Procedures (11/15/83)
IV.2 Compliance Assurance (11/15/83)
IV.3 Testing Procedures (11/15/83)

                    Section V Ambient Air Monitoring

ADEC Ambient Analysis Procedures (11/15/83)
[56 FR 19287, Apr. 26, 1991]



Sec. 52.76  1990 Base Year Emission Inventory.

    EPA approves as a revision to the Alaska State Implementation Plan 
the 1990 Base Year Carbon Monoxide Emission Inventory for the Anchorage 
and Fairbanks areas designated as nonattainment for CO, submitted by the 
Alaska Department of Environmental Conservation on December 29, 1993. 
This submittal consists of the 1990 base year stationary, area, non-road 
mobile, and on-road mobile sources for the pollutant carbon monoxide.
[62 FR 6132, Feb. 11, 1997]



Secs. 52.77--52.81  [Reserved]



Sec. 52.82  Extensions.

    The Administrator, by authority delegated under section 186(a)(4) of 
the Clean Air Act, as amended in 1990, hereby extends for one year 
(until December 31, 1996) the attainment date for the MOA, Alaska CO 
nonattainment area.
[61 FR 33678, June 28, 1996]



Secs. 52.83--52.95  [Reserved]



Sec. 52.96  Significant deterioration of air quality.

    (a) The State of Alaska Department of Environmental Conservation Air 
Quality Control Regulations as in effect on June 2, 1988 (specifically 
18 AAC 50.020, 50.021, 50.300, 50.400, 50.510, 50.520, 50.530, 50.600, 
50.620, and 50.900) and the State air quality control plan as in effect 
on June 2, 1988 (specifically, Section I.B. AIR QUALITY CONTROL REGIONS, 
Section I.C. ATTAINMENT/NONATTAINMENT DESIGNATIONS, Section I.D. 
PREVENTION OF SIGNIFICANT DETERIORATION DESIGNATIONS, Section IV.F. 
FACILITY REVIEW PROCEDURES, Section IV.G APPLICATION REVIEW AND PERMIT 
DEVELOPMENT, Section IV.H PERMIT ISSUANCE REQUIREMENTS, Appendix IV.1. 
PSD area Classification and Reclassification, and Appendix V ADEC 
Ambient Analysis Procedures), are approved as meeting the requirements 
of part C for preventing significant deterioration of air quality.
    (b) The requirements of sections 160 through 165 of the Clean Air 
Act are not met for Indian reservations since the plan does not include 
approvable procedures for preventing the significant deterioration of 
air quality on Indian reservations and, therefore, the provisions of 
Sec. 52.21 (b) through (w) are hereby incorporated and made part of the 
applicable reservation in the State of Alaska.
[48 FR 30626, July 5, 1983, as amended at 56 FR 19288, Apr. 26, 1991]



                           Subpart D--Arizona



Sec. 52.111  Toll free number assignment.

    Toll free numbers shall be made available on a first-come, first-
served basis unless otherwise directed by the Commission.
[63 FR 16441, Apr. 3, 1998]



Sec. 52.120  Identification of plan.

    (a) Title of plan: ``The State of Arizona Air Pollution Control 
Implementation Plan.''
    (b) The plan was officially submitted on January 28, 1972.
    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) Letter of intent to revise plan submitted on March 1, 1972, by 
the Arizona State Board of Health.
    (2) Letter of intent to revise plan submitted on March 2, 1972, by 
the Governor.
    (3) Revised implementation plan submitted on May 30, 1972, by the 
Governor.
    (i) Maricopa County Bureau of Air Pollution Control.
    (A) Previously approved on September 22, 1972 and now deleted 
without replacement Rules 60 to 67.
    (4) Transportation control plan submitted on April 11, 1973, by the 
Governor.

[[Page 71]]

    (5) Amendments (Non-regulatory) to the transportation control plan 
submitted on May 10, 1973, by the Governor.
    (6) Arizona Air Pollution Control Regulations (numbers in 
parentheses indicate recodification of regulations as identified in the 
Arizona State Implementation Plan Semi-Annual Report submitted to EPA on 
September 4, 1975).

7-1-1.1 (R9-3-101)  (Policy and Legal Authority)
7-1-1.3 (R9-3-103)  (Air Pollution Prohibited)
7-1-1.5 (R9-3-105)  (Enforcement)
7-1-4.3 (R9-3-403)  (Sulfur Emissions: Sulfite Pulp Mills)
7-1-4.4 (R9-3-404)  (Sulphur Emissions: Sulfuric Acid Plants)
7-1-4.5 (R9-3-405)  (Sulphur Emissions: Other Industries)
7-1-5.1 (R9-3-501)  (Storage of Volatile Organic Compounds)
7-1-5.2 (R9-3-502)  (Loading of Volatile Organic Compounds)
7-1-5.3 (R9-3-503)  (Organic Compound Emissions: Pumps and Compressors)
7-1-5.4 (R9-3-504)  (Organic Solvents)
7-1-6.1 (R9-3-601)  (Carbon Monoxide Emissions: Industrial)
7-1-7.1 (R9-3-701)  (Nitrogen Oxide Emissions: Fuel Burning 
          Installations)
7-1-7.2 (R9-3-702)  (Nitrogen Oxide Emissions: Nitric Acid Plants
7-1-8.3 (R9-3-803)  (New Installations)

    Submitted on August 20, 1973.
    (7) Revised transportation control plan submitted on September 11, 
1973, by the Governor.
    (8) Letter supplementing the revised transportation control plan 
encouraging mass transit, carpooling, etc., submitted on September 21, 
1973, by the Governor.
    (9) Letter supplementing the revised transportation control plan 
encouraging mass transit, carpooling, etc., submitted on October 2, 
1973, by the Governor.
    (10) Maricopa County Air Pollution Control District Regulation III, 
Rule 31 (Particulate Matter Emissions) submitted on January 28, 1974.
    (11) Arizona Air Pollution Control Regulation 7-1-1.7 (R9-3-107) 
(Unlawful open burning) submitted on February 19, 1974.
    (12) Pima County Air Pollution Control District Regulation II, Rule 
2 (Particulate matter emissions) submitted on March 19, 1974.
    (13) Air quality maintenance area designation analysis submitted on 
April 17, 1974, by the Arizona Department of Health Services.
    (14) Arizona Air Pollution Control Regulations:

7-1-2.10 (R9-3-210)  (Emergency Episode Criteria)
7-1-4.2 (R9-3-402)  (Sulfur Emissions: Fuel Burning Installations)

    Submitted on August 30, 1974.
    (15) Arizona Air Pollution Control regulations 7-1-8.1 (R9-3-801) 
(Original State jurisdiction); 7-1-8.2 (R9-3-802) (Assertions of 
jurisdiction); 7-1-8.3 (R9-3-803) (Delegation of authority); 7-1-11.3 
(R9-3-1203) (Suspension and revocation of permits); 7-1-11.4 (R9-3-1204) 
(Permits non-transferable); 7-1-11.5 (R9-3-1205) (Posting of permits); 
7-1-11.6 (R9-3-1206) (Notice by permit agencies); 7-1-11.7 (R9-3-1207) 
(Equipment covered); 7-1-11.9 (R9-3-1209) (Permit Fees); and 7-1-1.4 
(R9-3-104) (Recordkeeping and reporting) submitted September 27, 1974.
    (16) Assertion of State Jurisdiction over Apache, Navajo, Santa Cruz 
and Yavapai Counties; Assertion of State Jurisdiction over Cochise 
County; and Assertion of State Jurisdiction over specific sources in 
Mohave County.
    Submitted on February 3, 1975.
    (17) Amendments to the Rules and Regulations of the Pima County Air 
Pollution Control District (Regulation I: Rules 2, 4D, 4E, 4J, 8G, 16C, 
29, and 30) submitted on February 20, 1975, by the Director, Arizona 
Department of Health Services (the Governor's official representative).
    (18) Air pollution control regulations for various counties 
submitted by the Governor on July 1, 1975, as follows:
    (i) Coconino County Air Pollution Control Regulations.

12-1-1  (Legal Authority)
12-1-2  (Definitions)
12-1-3  (Air Pollution Prohibited)
12-2-2  (Operating Permits)
12-2-4  (Permit Fees)
12-2-5  (Permit Renewals)
12-2-7  (Testing of Installations)
12-2-8  (Compliance with Terms of Installation Permit)
12-2-9  (Notification of Denial of Permit)
12-2-10  (Appeals to the Hearing Board)
12-2-11  (Permits Not Transferable)
12-2-12  (Expiration of Installation Permit)
12-2-13  (Posting of Permits)

[[Page 72]]

12-3-1  (Ambient Air Quality Standards)
12-3-2  (Emission Standards)
12-3-3  (Reporting of Emissions)
12-3-4  (Production of Records: Confidentiality)
12-3-5  (Monitoring Devices)
12-3-6  (Penalty for Violation)
12-4-1  (Shade, Density, or Opacity of Emissions)
12-4-2  (Dust Control)
12-4-3  (Processing of Animal or Vegetable Matter)
12-4-4  (Volatile and Odorous Materials)
12-4-5  (Storage and Handling of Petroleum Products)
12-5-1  (Permit Required)
12-5-2  (Performance Tests: Permit Tags)
12-5-3  (Emission Limitations)
12-5-4  (Authority of Other Public Agencies)
12-6-1  (Unlawful Open Burning)
12-6-2  (Exceptions Requiring no Permission)
12-6-3  (Exceptions Requiring Permission)
12-6-4  (Exceptions Under Special Circumstances)
12-7-1  (Misdemeanor: Penalty)
12-7-2  (Order of Abatement)
12-7-3  (Hearings on Orders of Abatement)
12-7-5  (Notice of Hearing; Publication; Service)
12-7-6  (Injunctive Relief)
(A) Previously approved on November 15, 1978 and now deleted without 
          replacement Rules 12-7-2, 12-7-3, 12-7-5, and 12-7-6.

    (ii) Mohave County Air Pollution Control Regulations.

Sec. 1, Reg. 1  (Policy and Legal Authority)
Sec. 1, Reg. 2  (Definitions)
Sec. 1, Reg. 3  (Air Pollution Prohibited)
Sec. 1, Reg. 4  (Enforcement)
Sec. 2, Reg. 1  (Shade, Density or Opacity of Emissions)
Sec. 2, Reg. 2  (Particulate Matter)
Sec. 2, Reg. 3  (Reduction of Animal or Vegetable Matter)
Sec. 2, Reg. 4  (Evaporation and Leakage)
Sec. 2, Reg. 5  (Storage Tanks)
Sec. 3, Reg. 1  (Particulate Matter from Fuel Burning Installations)
Sec. 3, Reg. 2  (Particulate Matter from Other Sources)
Sec. 3, Reg. 3 (Sulfur from Primary Copper Smelters)
Sec. 3, Reg. 4  (Ground Level Concentrations)
Sec. 3, Reg. 5  (Exceptions)
Sec. 3, Reg. 6  (Incinerators)
Sec. 4, Reg. 1 and Reg. 2  (Responsibility and Requirements of Testing)
Sec. 5, Reg. 1  (Open Fires: Prohibition and Exceptions)
Sec. 6, Reg. 1  (Sulfur Dioxide)
Sec. 6, Reg. 2  (Non-Specific Particulate)
Sec. 6, Reg. 3  (Evaluation)
Sec. 6, Reg. 4 (Anti-Degradation)
Sec. 7  (Violations)

    (iii) Yuma County Air Pollution Control Regulations.

8-1-1.1  (Policy and Legal Authority)
8-1-1.2  (Definitions)
8-1-1.3  (Air Pollution Prohibited)
8-1-1.4  (Recordkeeping and Reporting)
8-1-1.5  (Enforcement)
8-1-1.6  (Exceptions)
8-1-2.1  (Non-Specific Particulate)
8-1-2.2  (Sulfur Dioxide)
8-1-2.3  (Non-Methane Hydrocarbons)
8-1-2.4  (Photochemical Oxidants)
8-1-2.5  (Carbon Monoxide)
8-1-2.6  (Nitrogen Dioxide)
8-1-2.7  (Evaluation)
8-1-2.10  (Emergency Episode Criteria)
8-1-3.1  (Visible Emissions; General)
8-1-3.2  (Fugitive Dust)
8-1-3.3  (Particulates--Incineration)
8-1-3.4  (Particulates--Wood Waste Burners)
8-1-3.5  (Particulates--Fuel Burning Equipment)
8-1-3.6  (Particulates--Process Industries)
8-1-4.2  (Fuel Burning Installations)
8-1-4.3  (Sulfur Emissions--Sulfite Pulp Mills)
8-1-4.4  (Sulfur Emissions--Sulfuric Acid Plants)
8-1-4.5  (Sulfur Emissions--Other Industries)
8-1-5.1  (Storage of Volatile Organic Compounds)
8-1-5.2  (Loading of Volatile Organic Compounds)
8-1-5.3  (Pumps and Compressors)
8-1-5.4  (Organic Solvents; Other Volatile Compounds)
8-1-6.1  (CO2 Emissions--Industrial)
8-1-7.1  (NO2 Emissions--Fuel Burning Equipment)
8-1-7.2  (NO2 Emissions--Nitric Acid Plants)
8-1-8.1  (Open Burning--Prohibition)
8-1-8.2  (Open Burning--Exceptions)

    (iv) Pinal-Gila Counties Air Pollution Control Regulations.

7-1-1.1  (Policy and Legal Authority)
7-1-1.2  (Definitions)
7-1-1.3  (Air Pollution Prohibited)
7-1-2.2  (Permit Unit Description and Fees)
7-1-2.4  (Appeals to Hearing Board)
7-1-2.5  (Transfer: Posting: Expirations)
7-1-2.6  (Recordkeeping and Reporting)
7-1-2.7  (Enforcement)
7-1-2.8  (Exceptions)
7-1-4.1 and 7-1-4.2  (Orders of Abatement)
7-1-5.1  (Classification and Reporting: Production of Records: 
          Violation: and Penalty)
7-1-5.2  (Special Inspection Warrant)
7-1-5.3  (Decisions of Hearing Boards: Subpoenas)
7-1-5.4  (Judicial Review: Grounds: Procedures)
7-1-5.5  (Notice of Hearing: Publication: Service)

[[Page 73]]

7-1-5.6  (Injunctive Relief)
7-2-1.1  (Non-Specific Particulate)
7-2-1.2  (Sulfur Dioxide)
7-2-1.3  (Non-Methane Hydrocarbons)
7-2-1.4  (Photochemical Oxidants)
7-2-1.5  (Carbon Monoxide)
7-2-1.6  (Nitrogen Dioxide)
7-2-1.7  (Evalution)
7-2-1.8  (Anti-Degradation)
7-3-1.1  (Visible Emissions: General)
7-3-1.2  (Particulate Emissions--Fugitive Dust)
7-3-1.3  (Open Burning)
7-3-1.4  (Particulate Emissions--Incineration)
7-3-1.5  (Particulate Emissions--Wood-Waste Burners)
7-3-1.6  (Reduction of Animal or Vegetable Matter)
7-3-1.7  (Particulate Emissions--Fuel Burning Equipment)
7-3-1.8  (Particulate Emissions--Process Industries)
7-3-2.1 (Copper Smelters)
7-3-2.2  (SO2 Emissions--Fuel Burning Installations)
7-3-2.3  (SO2 Emissions--Sulfite Pulp Mills)
7-3-2.4  (SO2 Emissions--Sulfuric Acid Plants)
7-3-2.5  (Other Industries)
7-3-3.1  (Storage of Volatile Organic Compounds)
7-3-3.2  (Loading of Volatile Organic Compounds)
7-3-3.3  (Pumps and Compressors)
7-3-3.4  (Organic Solvents: Other Volatile Compounds)
7-3-4.1  (CO2 Emissions--Industrial)
7-3-5.1  (NO2 Emissions--Fuel Burning Equipment)
7-3-5.2  (NO2 Emissions--Nitric Acid Plants)
7-3-6.1  (Policy and Legal Authority)
(A) Previously approved on November 15, 1978 and now deleted without 
          replacement Rules 7-1-4.1 to 7-1-4.2 and 7-1-5.1 to 7-1-5.6.

    (19) Arizona Air Pollution Control Regulations:

R9-3-102  (Definitions)
R9-3-108  (Test Methods and Procedures)
R9-3-301  (Visible Emissions--General)
R9-3-302  (Particulate Emissions: Fugutive Dust)
R9-3-303  (Particulate Emissions: Incineration)
R9-3-304  (Particulate Emissions: Wood Waste Burners)
R9-3-305  (Particulate Emissions: Fuel Burning Equipment)
R9-3-307  (Particulate Emissions: Portland Cement Plants)
R9-3-308 (Particulate Emissions: Heater-Planers)

    Submitted on September 16, 1975.
    (20) Arizona Air Pollution Control Regulations R9-3-505 (Gasoline 
Volatility Testing); R9-3-506 (Gasoline Volatility Standards); R9-3-1001 
(Policy and Legal Authority); R9-3-1020 (State Stations Acting as Fleet 
Inspection Stations); any Fleet Inspection Stations for State Stations); 
submitted on January 23, 1976.
    (21) Amendments to the rules and Regulations of the Pima County Air 
Pollution Control District (Regulation I:

    Rule 2 (paragraph uu-yy, Definitions); regulation II (Fuel Burning 
Equipment): Rule 2G (paragraphs 1-4c, Particulate Emissions), Rule 7A 
(paragraphs 1-6, Sulfur Dioxide Emissions), Rule 7B (paragraphs 1-4, 
Nitrogen Oxide Emission); Regulation VI: Rule 1A-H, (Ambient Air Quality 
Standards); Regulation VII (paragraph A-D, Standards of Performance for 
New Stationary Sources); and Regulation VIII (paragraphs A-C, Emission 
Standards for Hazardous Air Pollutants)) submitted on September 30, 1976 
by the Director, Arizona Department of Health Services (the Governor's 
official representative).

    (22)--(23) [Reserved]
    (24) Arizona Air Pollution Control Regulations R9-3-1002 
(Definitions); R9-3-1003 (Vehicles To Be Inspected by the Mandatory 
Vehicular Emissions Inspection Program); R9-3-1004 (State Inspection 
Requirements); R9-3-1005 (Time of Inspections); R9-3-1006 (Mandatory 
Vehicular Emissions Inspection); R9-3-1007 (Evidence of Meeting State 
Inspection Requirements); R9-3-1008 (Procedure for Issuing Certificates 
of Waiver); R9-3-1010 (Low Emissions Tune Up); R9-3-1011 (Inspection 
Report); R9-3-1012 (Inspection Procedure and Fee); R9-3-1013 
(Reinspections); R9-3-1016 (Licensing of Inspectors); R9-3-1017 
(Inspection of Governmental Vehicles); R9-3-1018 (Certificate of 
Inspection); R9-3-1019 (Fleet Station Procedures and Permits); R9-3-1022 
(Procedure for Waiving Inspections Due to Technical Difficulties); R9-3-
1023 (Certificate of Exemption); R9-3-1025 (Inspection of State 
Stations); R9-3-1026 (Inspection of Fleet Stations); R9-3-1027 
(Registration of Repair Industry Analyzers); R9-3-1029 (Vehicle Emission 
Control Devices); and R9-3-1030 (Visible Emissions; Diesel-Powered 
Locomotives); submitted on February 11, 1977.

[[Page 74]]

    (25) [Reserved]
    (26) Maricopa County Air Pollution Control District Regulation IV, 
rule 41, paragraph B (Continuously Monitoring and Recording Emissions) 
submitted on July 29, 1977.
    (27) The following amendments to the plan were submitted on January 
4, 1979 by the Governor's designee.
    (i) Arizona State Rules and Regulations for Air Pollution Control.

    (A) R-9-3-101, A., Nos. 2, 3, 29, 41, 53, 55, 87, 88, 89, 91, 92, 
95, 100 and 117; R9-3-301, paragraphs D, J, and N; R9-3-306, paragraphs 
D and J; and R9-3-307, paragraphs C and E.
    (B) New or amended Rules R9-3-101 (Nos. 1, 4, 6, (a, c, and d), 8, 
9, 11, 13, 17 to 26, 28, 30 to 35, 37 to 40, 43 to 45, 48, 49, 54, 57 to 
59, 61 to 73, 77 to 80, 82, 83, 86, 90, 94, 96, 98, 101, 102, 104, 105, 
107 to 115, 118 to 120, 122, to 129, and 131), R9-3-217, R9-3-218, R9-3-
219, R9-3-308, R9-3-310 (Paragraph C), R9-3-311 (Paragraph A), R9-3-312, 
R9-3-313 (Paragraphs A.1, A.2.b, A.3, A.4, B to D.1, D.3, D.4.a to 
F.1.2.iii, F.1.b., and F.2.b. to F.4), R9-3-314 to R9-3-319, R9-3-402 to 
R9-3-404, R9-3-406, R9-3-407, R9-3-409, R9-3-410, R9-3-502 (Paragraphs 
B, C, C.2, and D to G), R9-3-503 (Paragraph A), R9-3-504 (Paragraphs B 
and C), R9-3-505 (Paragraphs A, B.1.b., B.2.b, and B.3 to D), R9-3-506 
(Paragraphs A.2, B, C.1.a to C.4), R9-3-507 (Paragraphs D to F), R9-3-
508 (Paragraphs A and C), R9-3-510 (Paragraphs B to E), R9-3-511 
(Paragraph B), R9-3-512 (Paragraph B), R9-3-513 (Paragraphs B and C), 
R9-3-514 (Paragraphs B and C), R9-3-516 (Paragraph B), R9-3-517 
(Paragraphs B and C), R9-3-518 (Paragraphs B and C), R9-3-519 
(Paragraphs A.2, A.3.a to A.3.c, A.3.e and B to C), R9-3-520 (Paragraphs 
B and C), R9-3-521 (Paragraphs B to D), R9-3-522 (Paragraphs A.1 to A.5, 
B and C), R9-3-523 (Paragraph B), R9-3-524 (Paragraphs C, D.1, D.2, D.4 
to G.5), R9-3-525 (Paragraphs B to D), R9-3-526, R9-3-527, R9-3-528 
(Paragraphs B to E and F.1 to F.4), R9-3-601 to R9-3-605, R9-3-1101, R9-
3-1102, Appendix 10 (Sections A10.1.3.3, A10.1.4. and A10.2.2 to 
A10.3.4.) and Appendix 11.

    (28) The following amendments to the plan were submitted on January 
18, 1979 by the Governor's designee.
    (i) Maricopa County Bureau of Air Pollution Control Rules and 
Regulations.

    (A) Rule 33, Storage and Handling of Petroleum Products.
    (B) New or amended Rules 21G and 41.

    (29) The following amendments to the plan were submitted on January 
23, 1979, by the Governor's designee.
    (i) Arizona State Rules and Regulations for Air Pollution Control.

    (A) Arizona Testing Manual for Air Pollutant Emissions (excluding 
Sections 2.0 and 5.0).

    (30) Redesignation of AQCR's in Arizona, submitted on January 26, 
1979, by the Governor.
    (31) Revisions to the Arizona Air Pollution Control Regulations 
submitted on March 21, 1979:

    R9-3-1002 (22,34); R9-3-1003 [A(A8-11),B,C]; R9-3-1005 [A, (A3)]; 
R9-3-1006 [A,(A1,2),B, (B2,3,4,5),D,E, (E1(c),2(c)),F,G, (G1,2), Table 
II]; R9-3-1008 [B,(B1,2,6,7)]; R9-3-1010 [A,(A3),C,D,F]; R9-3-1011 
[A,B,(B1,2,3)];R9-3-1012(b); R9-3-1014; R9-3-1017 [B,(B4), C, E]; R9-3-
1019 [A,B,D, D(1)(a)(i), D(1)(a)(ii)(6), D(1)(a)(iii), D(1)(c), 
D(1)(f)(11), H, (H1,2), I(I8,9,10,11,12,13), J, (J10), L, M, N, (N1,2)]; 
R9-3-(C,E); R9-3-1022(B); R9-3c-091023(A,B); R9-3-1027(F).

    (32) The following amendments to the plan were submitted on February 
23, 1979 by the Governor's designee.
    (i) Nonatainment Area Plan for Carbon Monoxide and Photochemical 
Oxidants, Maricopa County Urban Planning Area.
    (33) The Metropolitan Pima County Nonattainment Area Plan for CO was 
submitted by the Governor's designee on March 20, 1979.
    (34) The Metropolitan Pima County Nonattainment Area Plan for TSP 
was submitted by the Governor's designee on March 27, 1979.
    (35) The following amendments to the plan were submitted on April 
10, 1979, by the Governor's designee.
    (i) Yuma County Air Pollution Control District.

    (A) New or amended Rules 8-1-1.2 8-1-1.3 thru 8-1-1.6 and 8-1-1.8 
thru 8-1-1.13; 8-1-2.1 thru 8-1-2.6 and 8-1-2.8; 8-1-3.1 thru 8-1-3.6, 
8-1-3.7 (except paragraph ``F'') and 8-1-3.8 thru 8-1-3.20; and 
Appendices I and II.

    (36) The following amendments to the plan were submitted on July 3, 
1979 by the Governor's designee.
    (i) Revision to the Nonattainment Area Plan for Carbon Monoxide and 
Photochemical Oxidants, Maricopa County Urban Planning Area.
    (37) The following amendments to the plan were submitted on 
September 20, 1979 by the Governor's designee.
    (i) Arizona State Rules and Regulations for Air Pollution Control.

    (A) New or amended rule R9-3-515 (Paragraphs C.1.a. to C.1.h.; C.2; 
C.3, C.3.b., C.3.c.,

[[Page 75]]

and C.3.h.; C.4.c. to C.4.g. and C.4.i.; C.5 and C.5.b. to C.5.d.; 
C.6.b.i. to C.6.b.iii., C.6.b.vi., C.6.b.vii., and C.6.c.; and C.8.).

    (ii) ``ASARCO Incorporated, Hayden Copper Smelter, State 
Implementation Plan Determination of Good Engineering Practice Stack 
Height,'' September 17, 1979, issued by ADHS.
    (38) The following amendment to the plan were submitted on October 
9, 1979, by the Governor's designee.
    (i) Pima County Health Department.

    (A) New or amended Regulation 10:
    Rules 101-103; Regulation 11: Rules 111-113; Regulation 12: Rules 
121-123; Regulation 13: Rules 131-137; Regulation 14: Rules 141 and 143-
147; Regulation 15: Rule 151; Regulation 16: Rules 161-165; Regulation 
17: Rules 172-174; Regulatiotion 24: Rules 241 and 243-248; Regulation 
25: Rules 251 and 252; Regulation 30: Rules 301 and 302; Regulation 31: 
Rules 312-316 and 318; Regulation 32: Rule 321; Regulation 33: Rules 331 
and 332; Regulation 34: Rules 341-344; Regulation 40: Rules 402 and 403; 
Regulation 41: Rules 411-413; Regulation 50: Rules 501-503 and 505-507; 
Regulation 51: Rules 511 and 512; Regulation 60: Rule 601; Regulation 
61: Rule 611 (Paragraph A.1 to A.3) and Rule 612; Regulation 62: Rules 
621-624; Regulation 63: Rule 631; Regulation 64: Rule 641; Regulation 
70: Rules 701-705 and 706 (Paragraphs A to C, D.3, D.4, and E); 
Regulation 71: Rules 711-714; Regulation 72: Rules 721 and 722; 
Regulation 80: Rules 801-804; Regulation 81: Rule 811; Regulation 82: 
Rules 821-823; Regulation 90: Rules 901-904; Regulation 91: Rules 911 
(except Methods 13-A, 13-B, 14, and 15; and Rules 912, and 913; 
Regulation 92: Rules 921-924; and Regulation 93: Rules 931 and 932.
    (B) New or amended Regulation 17: Rule 171, paragraphs B.1, B.1.a, 
B.7, B.8, C.1.a, C.1.b, C.2.a, C.2.c, C.2.d, C.3.a, and E.1.b; 
Regulation 42: Rules 421, 422, 423, 424, 425, and 426; and Regulation 
50: Rule 504.
    (C) Previously approved on April 16, 1982 and now deleted without 
replacement Rules 141, 143 to 147, 702, 711 to 714.

    (39) The following amendments to the plan were submitted on November 
8, 1979 by the Governor's designee.
    (i) Nonattainment Area Plan for Total Suspended Particulates, 
Maricopa County Urban Planning Area.
    (40) [Reserved]
    (41) The following amendments to the plan were submitted on February 
15, 1980, by the Governor's designee.
    (i) 1.0 Air Quality Surveillance Network.
    (42) The Technical Basis of New Source Review Regulations, Pima 
County, Arizona, February 6, 1980 (AQ-125-a) was submitted by the 
Governor's designee on February 28, 1980.
    (43) The following amendments to the plan were submitted on April 1, 
1980 by the Governor's designee.
    (i) Arizona State Rules and Regulations for Air Pollution Control.

    (A) R9-3-101, A., Nos. 7, 27, 46, 52, 54, 72, 73, 74, 81, 84, 85, 
86, 88, 89, 92, 96, 97, 98, 111, 117, 118, and 122; R9-3-301, paragraphs 
B-1, B-2, C, E, F, H, I, J, K, M, N, O, P, and Q; R9-3-302, (except 
paragraphs D, E, and I); R9-3-303; R9-3-306, paragraphs B-2, C-1, C-3, 
and C-5 to C-7, E, F, G-1, G-3, G-4, H, and I; and R9-3-307, paragraphs 
A, B, D, and F.
    (B) New or amended Rules R9-3-101 (Nos. 5, 15, 16, 42, 49, 51, 55, 
94, 101, 103, 106, 126, 127, and 133), R9-3-201 (paragraph D.2), R9-3-
202 (Paragraph D.2), R9-3-203 (Paragraph D.2), R9-3-204 (Paragraph C.2), 
R9-3-205 (Paragraph C.2), R9-3-206 (Paragraph C.2), R9-3-207 (Paragraph 
C.2), R9-3-313 (Paragraph F.1.a.i and ii), R9-3-401, R9-3-405, R9-3-408, 
R9-3-501 (Paragraph A to C), R9-3-502 (Paragraph A to A.4), R9-3-503 
(Paragraphs B, C.1,C.2.a. to C.2.f., C.4 and C.5), R9-3-504 (Paragraph 
A.1 to A.4), R9-3-508 (Paragraph B.1 to B.6), R9-3-510 (Paragraph A.1 
and A.2), R9-3-511 (Paragraph A.1 to A.5), R9-3-512 (Paragraph A.1 to 
A.5), R9-3-513 (Paragraph A.1 to A.5), R9-3-514 (Paragraph A.2), R9-3-
516 (Paragraph A.1 to A.6), R9-3-517 (Paragraph A.1 to A.5), R9-3-518 
(Paragraph A.1 to A.5), R9-3-520 (Paragraph A.1 to A.6), R9-3-521 
(Paragraph A.1 to A.5), and Appendices 1 and 2.

    (ii) Arizona Lead SIP Revision.
    (44) The following amendments to the plan were submitted on June 23, 
1980 by the Governor's designee.
    (i) Maricopa County Bureau of Air Pollution Control Rules and 
Regulations.

    (A) Rule 34, Organic Solvents.
    (B) New or amended Rules 2 (except 49 and 57), 3, 24, 25, 25, 26, 
27, 30, 31(A), (B), and (H), 32, (G), (H), (J), and (K), 40, 70-72, and 
74 and deletion of ``ee''.

    (45) The following amendments to the plan were submitted on July 17, 
1980 by the Governor's designee.
    (i) Arizona State Rules and Regulations for Air Pollution Control.

    (A) R-9-3-101, A., Nos. 73, 74, 75, 83, 86, 87, 88, 90, 91, 94, 98, 
99, 100, 113, 119, 120, and 124; R9-3-301, paragraphs A, B-3, G, I, J, 
K, L, M, N, O, P, Q, and R; R9-3-306, paragraphs A, B-1, B-3, B-4, C-2, 
C-4, and G-2; and R9-3-320, paragraphs B and C.
    (B) New or amended Rules R9-3-101 (Nos. 6(b), 10, 12, 14, 36, 50, 
55, 77, 84, and 92), R9-3-

[[Page 76]]

311 (Paragraph B), R9-3-313 (Paragraphs A.2.a., D.2, D.4, F.1.C, and 
F.2.a.), R9-3-320 (Paragraph A), R9-3-502 (Paragraph C.1), R9-3-503 
(Paragraph C, C.2, C.2.g. and C.3), R9-3-504 (Paragraph A), R9-3-505 
(Paragraph B.1.a, B.2.a), R9-3-506 (Paragraph A to A.1), R9-3-507 
(Paragraphs A to C), R9-3-508 (Paragraph B), R9-3-509, R9-3-510 
(Paragraph A), R9-3-511 (Paragraph A), R9-3-512 (Paragraph A), R9-3-513 
(Paragraph A), R9-3-514 (Paragraphs A to A.1), R9-3-516 (Paragraph A), 
R9-3-517 (Paragraph A), R9-3-518 (Paragraph A), R9-3-519 (Paragraph A to 
A.1, A.3, and A.3.d), R9-3-520 (Paragraph A), R9-3-521 (Paragraph A), 
R9-3-522 (Paragraph A), R9-3-523 (Paragraph A), R9-3-524 (Paragraphs A, 
B, D, and D.3), R9-3-525 (Paragraph A), R9-3-528 (Paragraphs A and F.5), 
Section 3, Method 11; Section 3.16, Method 16; Section 3.19, Method 19; 
Section 3.20, Method 20; and Appendix 10 (Sections A10.2 and A10.2.1).
    (C) New or amended Rule R9-3-515 (Paragraphs A; and C.6, C.6.b, and 
C.6.b.v.).

    (46) The following amendments to the plan were submitted on August 
7, 1980, by the Governor's designee.
    (i) Pinal-Gila Counties Air Quality Control District.

    (A) New or amended Rules 7-1-1.2, 7-1-1.3(C), 7-3-1.1, 7-3-1.4(C), 
7-3-1.7(F), and 7-3-3.4.

    (47) The following amendments to the plan were submitted on 
September 10, 1980, by the Governor's designee.
    (i) Arizona State Rules and Regulations and Air Pollution Control.

    (A) New or amended Rules R9-3-101 (Nos. 24, 55, 102, and 115 (25-54, 
56-101, 103-114, and 116-140 are renumbered only), R9-3-201 (Paragraphs 
A to D.1 and E), R9-3-202 (Paragraphs A to D.1 and E), R9-3-203 
(Paragraphs A to D.1 and E), R9-3-204 (Paragraphs A to C.1 and D), R9-3-
205 (Paragraphs A to C.1 and D), R9-3-206 (Paragraphs A to C.1 and D), 
R9-3-207 (Paragraphs A to C.1 and D), and R9-3-216.

    (48) Arizona Lead SIP Revision submitted by the State on September 
26, 1980.
    (49) The following amendments to the plan were submitted on July 13, 
1981 by the Governor's designee.
    (i) Arizona Revised Statute Sec. 36-1718.
    (50) The following amendments to the plan were submitted on July 13, 
1981, by the Governor's designee.
    (i) Arizona State Rules and Regulations for Air Pollution Control.

    (A) New or amended Rules R9-3-310 (Paragraphs A and B), R9-3-501 
(Paragraph D), R9-3-503 (Paragraph C.6), R9-3-506 (Paragraph C to C.1), 
and Appendix 10 (Sections A10.1-A10.1.3.2).
    (B) New or amended Rule R9-3-515 (Paragraph C.4.a. and C.4.b.).

    (ii) Arizona Revised Statutes.

    (A) Arizona County: Chapter 6, Article 8. Air Pollution, Sections 
36-770 to 36-778, 36-779 to 36-779.07, 36-780, 36-780.01, 36-781 to 36-
783, 36-784 to 36-784.04, 36-785, 36-785.01, 36-786 to 36-788, 36-789 to 
36-789.02, 36-790, and 36-791.
    (B) Arizona State: Chapter 14, Air Pollution, Article 1. State Air 
Pollution Control, Sections 36-1700 to 36-1702, 36-1704 to 36-1706, 36-
1707 to 36-1707.06, 36-1708, 36-1720.02, and 36-1751 to 36-1753.
    (C) Previously approved on June 18, 1982 and now deleted without 
replacement Statutes 36-781, 36-782, 36-784, 36-784.01 to 36-784.04, 36-
785, 36-785.01, and 36-786 to 36-788.

    (51) The following amendments to the plan were submitted on June 1, 
1981, by the Governor's designee.
    (i) Pima County Health Department.

    (A) New or amended Regulation 14:
    Rule 142; Regulation 20: Rule 204; Regulation 24: Rule 242; 
Regulation 26: Rule 261; Regulation 50: Rule 504; Regulation 61: Rule 
611 (Paragraph A); Regulation 70: Rule 706 (Paragraphs D.1 and D.2); and 
Regulation 91: Rule 911 (Methods 19 and 20).
    (B) Previously approved on April 16, 1982 and now deleted without 
replacement Rule 142.

    (52) The following amendments to the plan were submitted on August 
5, 1981, by the Governor's designee.
    (i) Arizona State Rules and Regulations for Air Pollution Control.

    (A) New or amended Rules R9-3-1002, R9-3-1003, R9-3-1005, R9-3-1006, 
R9-3-1008, R9-3-1010 to R9-3-1014, R9-3-1016, R9-3-1019, R9-3-1023, R9-
3-1025, R9-3-1027, and R9-3-1030.

    (ii) Arizona Revised Statutes.

    (A) Inspection and Maintenance--Chapter 14, Article 3. Annual 
Emissions Inspection of Motor Vehicles, Sections 36-1771 to 36-1775, 36-
1708.01, 36-1709 to 36-1711, 36-1712 to 36-1712.04, 36-1713, 36-1713.01, 
36-1714 to 36-1717, 36-1718, 36-1718.01, 36-1719, 36-1720, and 36-1776 
to 36-1780.
    (B) Previously approved on June 18, 1982 and now deleted without 
replacement Statutes 36-1709 to 36-1712, 36-1712.01 to 36-1712.04, 36-
1713, 36-1713.01, and 36-1714 to 36-1716.

    (53) The following amendments to the plan were submitted on March 8, 
1982, by the Governor's designee.

[[Page 77]]

    (i) Maricopa County Bureau of Air Pollution Control Rules and 
Regulations.

    (A) Rules 2 (Nos. 11 and 33, and deletion of Nos. 18, 49, 50, 52, 
and 54), 28 and 33.

    (ii) The Improvement Schedules for Transit System and Rideshare 
Program in Metropolitan Pima County.
    (54) The following amendments to the plan were submitted on June 3, 
1982 by the Governor's designee.
    (i) Arizona State Rules and Regulations for Air Pollution Control.

    (A) New or amended Rule R9-3-515 Paragraphs C to C.1. and C.1.i.; 
C.3.a. and C.3.d. to C.3.g.; C.4. and C.4.h.; C.5.a.; C.6.a. and 
C.6.b.iv.; and C.9.).
    (B) New or amended rules R9-3-101 (Nos. 3, 7, 8, 17, 18, 19, 20, 21, 
29, 34, 35, 37, 56, 61, 62, 63, 68, 69, 75, 77, 78, 79, 88, 89, 90, 91, 
98, 99, 101, 117, 122, 129, 133, 136, 146, and 157; 53 and 123 are 
deleted); R9-3-217; R9-3-301; R9-3-304; R9-3-305; R9-3-306 (paragraph A 
only); R9-3-320 (Repealed and Reserved); R9-3-1101 (paragraphs A, C, and 
D); Appendix 1; and Appendix 2.
    (C) New or amended rules R9-3-101 (Nos. 4 to 6, 9 to 16, 22 to 28, 
30 to 33, 36, 38 to 55, 57 to 60, 64 to 67, 70 to 74, 76, 80 to 87, 92 
to 97, 100, 102 to 116, 118 to 121, 123 to 128, 130 to 132, 134, 135, 
137 to 141, 142 to 145, 147 to 156, and 158 are renumbered only); R9-3-
219; R9-3-502 (paragraph A to A.1 and A.2); R9-3-505 (paragraph B to 
B.1, B.2, B.3, and B.4); R9-3-508 (paragraph B to B.1, B.2, and B.5); 
R9-3-511 (paragraph A to A.1 and A.2); R9-3-513 (paragraph A to A.1 and 
A.2); R9-3-516 (paragraph A to A.1 and A.2); R9-3-517 (paragraph A to 
A.1); R9-3-518 (paragraph A to A.1 and A.2); R9-3-520 (paragraph A to 
A.1 and A.2); R9-3-521 (paragraph A to A.1 and A.2); R9-3-522 (paragraph 
A to A.1 and A.2); and Appendix 8 (Sections A8.3.1 and A8.3.2).
    (D) New or amended rules R9-3-302 (paragraphs A-H); and R9-3-303 
(paragraphs A to C and E to I), adopted on May 26, 1982.
    (E) Previously approved and now removed (without replacement) rule 
R9-3-101, No. 46.

    (55) The following amendments to the plan were submitted by the 
Governor's designee on March 4, 1983.
    (i) Incorporation by reference.
    (A) Maricopa County Health Department, Bureau of Air Quality 
Control.

    (1) New or amended rule 21.0:A-C, D.1.a-d, and E adopted on October 
25, 1982.

    (56) The following amendments to the plan were submitted on February 
3, 1984, by the Governor's designee.
    (i) Arizona State Rules and Regulations for Air Pollution Control.

    (A) New or amended rules R9-3-101 (No.'s 98 and 158), R9-3-201 to 
R9-3-207, R9-3-215, R9-3-218, R9-3-310, R9-3-322, R9-3-402, R9-3-404, 
R9-3-502, R9-3-515 (paragraph (c)), R9-3-529, R9-3-1101, and Appendices 
I and II.
    (B) New or amended rules R9-3-101, Nos. 135 and 157, adopted on 
September 19, 1983.

    (57) The following amendments to the plan were submitted by the 
Governor's designee on April 17, 1985.
    (i) Incorporation by reference.
    (A) Maricopa County Health Department, Bureau of Air Quality 
Control.

    (1) New or amended regulations: rule 21.0: D.1., D.1.e, f, and g 
adopted on July 9, 1984.

    (58) The following amendments to the plan were submitted by the 
Governor's designee on October 18, 1985.
    (i) Incorporation by reference.
    (A) Pima County Health Department.

    (1) New or amended regulations: Regulation 16: Rule 166; Regulation 
17; Rules 171 and 175; Regulation 20: Rule 202; Regulation 37: Rules 
371, 372, 373, Figure 371-A, Figure 371-C, and Figure 372; and 
Regulation 38, Rule 381, A1, 2, 3, 4, 5, and B, adopted on December 6, 
1983.

    (59) The following amendments to the plan were submitted by the 
Governor's designee on October 24, 1985.
    (i) Incorporation by reference.
    (A) Arizona Department of Health Services.

    (1) New or amended rule R9-3-303, adopted on September 28, 1984.

    (60) The following amendments to the plan were submitted by the 
Governor's designee on October 5, 1987.
    (i) Incorporation by reference.
    (A) Arizona Department of Health Services.

    (1) New or amended rules R9-3-1001 (Nos. 8, 25, 33, 34, 38, 39, 40, 
and 43, No. 8), R9-3-1003, R9-3-1005, R9-3-1006, R9-3-1008, R9-3-1009, 
R9-3-1010, R9-3-1011, R9-3-1013, R9-3-1016, R9-3-1018, R9-3-1019, R9-3-
1025, R9-3-1026, R9-3-1027, R9-3-1028, R9-3-1030, and R9-3-1031, adopted 
on December 23, 1986.
    (2) Previously approved and now removed (without replacement), Rule 
R9-3-1014.

    (B) The Maricopa Association of Governments (MAG) 1987 Carbon 
Monoxide (CO) Plan for the Maricopa County Area, MAC CO Plan Commitments 
for Implementation, and Appendix A through E, Exhibit 4, Exhibit D, 
adopted on July 10, 1987.


[[Page 78]]


    (61) The following amendments to the plan were submitted by the 
Governor's designee on January 6, 1988.
    (i) Incorporation by reference.
    (A) The 1987 Carbon Monoxide State Implementation Plan Revision for 
the Tucson Air Planning Area adopted on October 21, 1987.

    (62) The following amendments to the plan were submitted by the 
Governor's designee on March 23, 1988.
    (i) Incorporation by reference.
    (A) Arizona Revised Statutes.

    (1) Senate Bill 1360: Section 6: ARS 15-1444-C (added), Section 7: 
QRS 15-1627-F (added), Section 21: ARS 49- 542-A (amended, Section 21: 
ARS 49-542-E (added), Section 21: ARS 49-542-J.3.(b) (amended), and 
Section 23: ARS 49-550-E (added), adopted on May 22, 1987.
    (2) Senate Bill 1360: Section 2: ARS 9-500.03 (added), Section 14: 
ARS 41-796.01 (added); Section 17: 49-454 (added), Section 18: 49-474.01 
(added), and Section 25: ARS 49-571 (added), adopted on May 22, 1987.

    (63) The following amendments to the plan were submitted by the 
governor's designee on May 26, 1988:
    (i) Incorporation by reference.
    (A) Travel reduction ordinances for Pima County: Inter governmental 
Agreement (IGA) between Pima County, City of Tucson, City of South 
Tucson, Town of Oro Valley and Town of Marana, April 18, 1988; Pima 
County Ordinance No. 1988-72, City of Tucson ordinance No. 6914, City of 
South Tucson Resolutions No. 88-01, 88-05, Town of Oro Valley 
Resolutions No. 162, 326 and 327, Town of Marana Resolutions No. 88-06, 
88-07 and Ordinance No. 88.06.

    (64) The following amendments to the plan were submitted by the 
Governor's designee on June 1, 1988.
    (i) Incorporation by reference.

    (A) Letter from the Arizona Department of Environmental Quality, 
dated June 1, 1988, committing to administer the provisions of the 
Federal New Source Review regulations consistent with EPA's 
requirements. The commitments apply to the issuance of, or revision to, 
permits for any source which is a major stationary source or major 
modification as defined in 40 Code of Federal Regulations, part 51, 
subpart I.

    (65) The following amendments to the plan were submitted by the 
Governor's designee on July 18, 1988.
    (i) Incorporation by reference.
    (A) Arizona Revised Statutes.

    (1) House Bill 2206, Section 2: ARS 15-1627 (amended); Section 6: 
Title 28, ARS Chapter 22, Article 1, ARS 28-2701, ARS 28-2702, ARS 28-
2703, ARS 28-2704, and ARS 28-2705 (added); Section 7: ARS 41.101.03 
(amended); Section 9: ARS 41-2605 (amended); Section 10: ARS 41-2066 
(amended); Section 11: ARS 41-2083 (amended); Section 13: Title 41, 
Chapter 15, Article 6, ARS 41-2121: Nos. 1, 3, 4, 5, 6, 7, 8, and 9, ARS 
41-2122, ARS 41-2123, ARS 41-2124 (added); Section 15: Title 49, Chapter 
3, Article 1, ARS 49-403 to 49-406 (added); Section 17: Title 49, 
Chapter 3, Article 3, ARS 49-506 (added); Section 18; ARS 49-542 
(amended); Section 19: ARS 49-550 (amended); Section 20: ARS 49-551 
(amended); Section 21: Title 49, Chapter 3, Article 5, ARS 49-553 
(added), Section 22: ARS 49-571 (amended); Section 23: Title 49, Chapter 
3, Article 8, ARS 49-581, ARS 49-582, ARS 49-583, ARS 49-584, ARS 49-
585; ARS 49-586, ARS 49-588, ARS 49-590, and ARS 49-593 (added); Section 
25: Definition of major employer, Section 27: Appropriations; Section 
29: Delayed effective dates, adopted on June 28, 1988.
    (2) House Bill 2206 section 6 which added, under Arizona Revised 
Statutes, title 28, chapter 22, new sections 28-2701 through 28-2708, 
and section 13 which added, under Arizona Revised Statutes, title 41, 
chapter 15, Article 6 new sections 41-2125A and 41-2125B. (Oxygenated 
fuels program for Pima County.)

    (66) The following amendments to the plan were submitted by the 
Governor's designee on July 22, 1988.
    (i) Incorporation by reference.
    (A) Letter from the Pima County Health Department, Office of 
Environmental Quality, dated April 24, 1988 committing to administer the 
New Source Review provisions of their regulations consistent with EPA's 
requirements. The commitments apply to the issuance of, or revision to, 
permits for any source which is a major stationary source of major 
modification as defined in 40 Code of Federal Regulations, part 51, 
subpart I.
    (B) Letter from Maricopa County Department of Health Services, 
Division of Public Health, dated April 28, 1988 and submitted to EPA by 
the Arizona Department of Environmental Quality July 25, 1988, 
committing to administer the New Source Review provisions of their 
regulations, consistent with EPA's requirements. These commitments apply 
to the issuance of, or revision to, permits for any source which is a 
major stationary source or major

[[Page 79]]

modification as defined in the Code of Federal Regulations, part 51, 
subpart I.
    (C) Addendum to MAG 1987 Carbon Monoxide Plan for the Maricopa 
County Nonattainment Area, July 21, 1988 (supplemental information 
related to the SIP revision of July 18, 1988).
    (D) Commitment in the July 22, 1988 submittal letter to apply the 
oxygenated fuels program of the July 18, 1988 submittal to Pima County.

    (67) Regulations for the Maricopa County Bureau of Air Pollution 
Control were submitted on January 4, 1990 by the Governor's designee.
    (i) Incorporation by reference.
    (A) Amended regulations: Regulation II, rule 220 and Regulation III, 
rule 335, both adopted July 13, 1988.
    (B) Amended Maricopa County Division of Air Pollution Control Rule 
314, adopted July 13, 1988.

    (68) The following amendments to the plan were submitted by the 
Governor's designee on June 11, 1991.
    (i) Incorporation by reference.
    (A) Arizona Revised Statutes.
    (1) House Bill 2181 (approved, May 21, 1991), section 1: Arizona 
Revised Statute (A.R.S.) 41-2065 (amended); section 2: A.R.S. 41-2083 
(amended); section 3: A.R.S. section 41-2122 (amended); section 4: 
A.R.S. Section 41-2123 (amended); and section 5: A.R.S. section 41-2124 
(repealed).
    (69) The following amendment to the plan was submitted by the 
Governor's designee on May 27, 1994.
    (i) Incorporation by reference.
    (A) Maricopa County Bureau of Air Pollution Control stage II vapor 
recovery program, adopted on August 27, 1993.
    (70) New and amended regulations for the Maricopa County 
Environmental Services Department--Air Pollution Control were submitted 
on June 29, 1992, by the Governor's designee.
    (i) Incorporation by reference.
    (A) New Rules 337, 350, and 351, adopted on April 6, 1992.
    (71) New and amended regulations for the following agencies were 
submitted on August 15, 1994 by the Governor's designee.
    (i) Incorporation by reference.
    (A) Pinal County Air Quality Control District.
    (1) Chapter 1, Article 3, section 1-3-140, subsections 5, 15, 21, 
32, 33, 35, 50, 51, 58, 59, 103, and 123, adopted on November 3, 1993; 
Chapter 3, Article 1, section 3-1-081(A)(8)(a), adopted on November 3, 
1993; Chapter 3, Article 1, section 3-1-084, adopted on August 11, 1994; 
and Chapter 3, Article 1, section 3-1-107, adopted on November 3, 1993.
    (72) New and amended plans and regulations for the following 
agencies were submitted on November 13, 1992 by the Governor's designee.
    (i) Incorporation by reference.
    (A) Arizona Department of Environmental Quality.
    (1) Small Business Stationary Source Technical and Environmental 
Compliance Assistance Program, adopted on November 13, 1992.
    (B) Maricopa County Environmental Quality and Community Services 
Agency.
    (1) Rule 340, adopted on September 21, 1992.
    (73)  [Reserved]
    (74) Plan revisions were submitted by the Governor's designee on 
March 3, 1994.
    (i) Incorporation by reference.
    (A) Maricopa County Environmental Services Department new Rule 316, 
adopted July 6, 1993, and revised Rule 311, adopted August 2, 1993. 
Note: These rules are restored as elements of the State of Arizona Air 
Pollution Control Implementation Plan effective September 3, 1997.
    (B) [Reserved]
    (75) Program elements submitted on November 14, 1994, by the 
Governor's designee.
    (i) Incorporation by reference.
    (A) Arizona Department of Environmental Quality.
    (1) Basic and Enhanced Inspection and Maintenance Vehicle Emissions 
Program. Adopted on September 15, 1994.
    (76) Program elements were submitted on February 1, 1995 by the 
Governor's designee.
    (i) Incorporation by reference.
    (A) Small Business Stationary Source Technical and Environmental 
Compliance Assistance Program, adopted on February 1, 1995.

[[Page 80]]

    (77) Amended regulations for the following agency were submitted on 
December 19, 1994, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Maricopa County Environmental Services Department.
    (1) Rule 334, adopted on September 20, 1994.
    (78) New and amended regulations for the Maricopa County 
Environmental Services Department--Air Pollution Control were submitted 
on February 4, 1993, by the Governor's designee.
    (i) Incorporation by reference.
    (A) New Rule 352, adopted on November 16, 1992.
    (B) [Reserved]
    (C) Rule 339, adopted on November 16, 1992.
    (79) New and amended regulations for the following agencies were 
submitted on June 29, 1992 by the Governor's designee.
    (i) Incorporation by reference.
    (A) Maricopa County Environmental Quality and Community Services 
Agency.
    (1) Rule 353, adopted on April 6, 1992.
    (80) New and amended regulations for the following agencies were 
submitted on August 10, 1992 by the Governor's designee.
    (i) Incorporation by reference.
    (A) Maricopa County Environmental Quality and Community Services 
Agency.
    (1) Rules 331 and 333, adopted on June 22, 1992.
    (81) Amended regulation for the following agency was submitted on 
August 16, 1994, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Maricopa County Environmental Services Department.
    (1) Rule 341, adopted on August 5, 1994.
    (82) New and amended rules and regulations for the Maricopa County 
Environmental Services Department--Air Pollution Control were submitted 
on August 31, 1995, by the Governor's designee.
    (i) Incorporated by reference.
    (A) Rule 343, adopted on February 15, 1995.
    (B) [Reserved]
    (C) Rule 351, revised on February 15, 1995.
    (D) Rule 318 and Residential Woodburning Restriction Ordinance, 
adopted on October 5, 1994.
    (E) Maricopa County.
    (1) Ordinance P-7, Maricopa County Trip Reduction Ordinance, adopted 
May 26, 1994.
    (83) New and revised rules and regulations for the Maricopa County 
Environmental Services Department-Air Pollution Control were submitted 
on February 26, 1997, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Rules 331, 333, and 334, revised on June 19, 1996, and Rule 338, 
adopted on June 19, 1996.
    (B) Rule 336, adopted on July 13, 1988 and revised on June 19, 1996.
    (84) Amended regulations for the Pinal County Air Quality Control 
District were submitted on November 27, 1995, by the Governor's 
designee.
    (i) Incorporation by reference.
    (A) Pinal County Air Quality Control District Code of Regulations: 
Chapter 1, Articles 1 through 3; Chapter 2, Articles 1 through 7; 
Chapter 3, Articles 1, 2, and the following sections of Article 3, 
Section 200, Section 203, Section 205, Section 210, Section 250, Section 
260, Section 270, Section 275, and Section 280. Adopted on October 12, 
1995.
    (85) New and revised rules and regulations for the Maricopa County 
Environmental Services Department-Air Pollution Countrol were submitted 
on March 4, 1997, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Rule 337, revised on November 20, 1996, and Rules 342 and 346, 
adopted on November 20, 1996.
    (86) [Reserved]
    (87) New and amended fuel regulations for the following Arizona 
Department of Environmental Quality plan revisions were submitted on 
April 29, 1997, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Arizona Revised Statutes.
    (1) Section 13 of H.B, 2001 (A.R.S. Sec. 41-2083(E)), adopted on 
November 12, 1993.
    (88) Plan revisions were submitted on May 7, 1997 by the Governor's 
designee.
    (i) Incorporation by reference.

[[Page 81]]

    (A) Maricopa County Environmental Services Department.
    (1) Rule 310, adopted September 20, 1994.
    (2) Resolution To Improve the Administration of Maricopa County's 
Fugitive Dust Program and to Foster Interagency Cooperation, adopted May 
14, 1997.
    (B) The City of Phoenix, Arizona.
    (1) A Resolution of the Phoenix City Council Stating the City's 
Intent to Work Cooperatively with Maricopa County to Control the 
Generation of Fugitive Dust Pollution, adopted April 9, 1997.
    (C) The City of Tempe, Arizona.
    (1) A Resolution of the Council of the City of Tempe, Arizona, 
Stating Its Intent to Work Cooperatively with Maricopa County to Control 
the Generation of Fugitive Dust Pollution, adopted March 27, 1997.
    (D) The Town of Gilbert, Arizona.
    (1) A Resolution of the Mayor and the Common Council of the Town of 
Gilbert, Maricopa County, Arizona, Providing for the Town's Intent to 
Work Cooperatively with Maricopa County, Arizona, to Control the 
Generation of Fugitive Dust Pollution, adopted April 15, 1997.
    (E) The City of Chandler, Arizona.
    (1) A Resolution of the City Council of the City of Chandler, 
Arizona, Stating the City's Intent to Work Cooperatively with Maricopa 
County to Control the Generation of Fugitive Dust Pollution, adopted 
March 27, 1997.
    (F) The City of Glendale, Arizona.
    (1) A Resolution of the Council of the City of Chandler, Maricopa 
County, Arizona, Stating Its Intent to Work Cooperatively with Maricopa 
County to Control the Generation of Fugitive Dust Pollution, adopted 
March 25, 1997.
    (G) The City of Scottsdale, Arizona.
    (1) A Resolution of the Scottsdale City Council Stating the City's 
Intent to Work Cooperatively with Maricopa County to Control the 
Generation of Fugitive Dust Pollution, adopted March 31, 1997.
    (H) The City of Mesa, Arizona.
    (1) A Resolution of the Mesa City Council Stating the City's Intent 
to Work Cooperatively with Maricopa County to Control the Generation of 
Particulate Air Pollution and Directing City Staff to Develop a 
Particulate Pollution Control Ordinance Supported by Adequate Staffing 
Levels to Address Air Quality, adopted April 23, 1997.
    (89) Plan revisions were submitted on September 12, 1997 by the 
Governer's designee.
    (i) Incorporation by reference
    (A) Arizona Cleaner Burning Gasoline Interim rule submitted as a 
revision to the Maricopa Country Ozone Nonattainment Area Plan, adopted 
on September 12, 1997.
    (90) Plan revisions were submitted on January 21, 1998 by the 
Governer's designee.
    (i) Incorporation by reference.
    (A) Arizona Cleaner Burning Gasoline Interim rule submitted as a 
revision to the PM-10 Maricopa County State Implementation Plan, adopted 
on September 12, 1997.
[37 FR 10849, May 31, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.120, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.121  Classification of regions.

    The Arizona plan is evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                                 Classifications
                  AQCR (constituent counties)                  -------------------------------------------------
                                                                   PM        SOX       NO2       CO        O3
----------------------------------------------------------------------------------------------------------------
Maricopa Intrastate (Maricopa)................................         I       III       III         I         I
Pima Intrastate (Pima)........................................         I        II       III       III         I
Northern Arizona Intrastate (Apache, Coconino, Navajo,
 Yavapai).....................................................         I       III       III       III       III
Mohave-Yuma Intrastate (Mohave, Yuma).........................         I       III       III       III       III
Central Arizona Intrastate (Gila, Pinal)......................         I        IA       III       III       III
Southeast Arizona Intrastate (Cochise, Graham, Greenlee, Santa
 Cruz)........................................................         I        IA       III       III       III
----------------------------------------------------------------------------------------------------------------

[45 FR 67345, Oct. 10, 1980]

[[Page 82]]



Sec. 52.122  [Reserved]



Sec. 52.123  Approval status.

    (a) With the exceptions set forth in this subpart, the Administrator 
approved Arizona's plan for the attainment of the national standards.
    (b) With the exception set forth in Secs. 52.130 and 52.135, the 
Administrator approves the inspection and maintenance (I/M) program for 
motor vehicles; the carpool matching program; certain transit 
improvements; and certain traffic flow improvement and site-specific 
traffic control measures.
    (c) With the exceptions set forth in this subpart, the Administrator 
approves the plan with respect to Part D, Title I of the Clean Air Act, 
as amended in 1977, for the nonattainment areas listed in this 
paragraph.
    (1) For TSP, the portion of the Tucson TSP Air Planning Area falling 
both within the area described by connecting the geographic points in 
the order listed below in this paragraph and within the townships and 
sections described below in this paragraph:

Latitude 32 deg.38.5' N, Longitude 111 deg.24.0' W
Latitude 32 deg.26.5' N, Longitude 110 deg.47.5' W
Latitude 32 deg.12.5' N, Longitude 110 deg.32.5' W
Latitude 31 deg.49.5' N, Longitude 110 deg.25.5' W
Latitude 31 deg.42.0' N, Longitude 110 deg.50.5' W
Latitude 31 deg.52.5' N, Longitude 111 deg.12.5' W
Latitude 31 deg.24.5' N, Longitude 111 deg.29.0' W

(and return to initial point)

    T9S, R9-11E
    T10S, R9-13E

    T13S, R13E: sections 5, 8-10, 13-17, 20-28, 33-36, 6 (NE and SE 
quarters only) and 7 (NE and SE quarters only)
    T13S, R14E: sections 19-21, 26-35
    T14S, R13E: sections 1-3, 10-14, 23-25
    T14S, R14E: sections 3-9, 17-19, 30
    T17S, R19E
    T18S, R19E
    T20S, R14-15E

    (d) With the exceptions set forth in this subpart, the Administrator 
approves the plan with respect to Part D, Title I of the Clean Air Act, 
as amended in 1977, for the nonattainment areas listed in this 
paragraph. In addition, continued satisfaction of the requirements of 
Part D for the ozone portion of the State Implementation Plan (SIP) 
depends on the adoption and submittal by January 1, 1981, of reasonably 
available control technology (RACT) requirements for sources covered by 
Control Technique Guidelines (CTG's) published between January 1978 and 
January 1979.
    (1) Maricopa County Urban Planning Area for O3.
    (e) The Administrator finds that the plan does not satisfy all the 
requirements of Part D, Title I, of the Clean Air Act as amended in 1977 
for the nonattainment and area pollutants listed in this paragraph.
    (1) Maricopa County Urban Planning Area for CO and TSP.
    (2) Tucson CO Air Planning Area for CO.
    (3) The following portion of the Tucson TSP Air Planning Area: The 
area described by connecting the following geographic points in the 
order listed below:

Latitude 32 deg.38.5' N, Longitude 111 deg.24.0' W
Latitude 32 deg.26.5' N, Longitude 110 deg.47.5' W
Latitude 32 deg.12.5' N, Longitude 110 deg.32.5' W
Latitude 31 deg.49.5' N, Longitude 110 deg.25.5' W
Latitude 31 deg.42.0' N, Longitude 110 deg.50.5' W
Latitude 31 deg.52.5' N, Longitude 111 deg.12.5' W
Latitude 31 deg.24.5' N, Longitude 111 deg.29.0' W

(and return to initial point)


Excluding the area within the following townships:

    T9S, R9-11E
    T10S, R9-13E
    T13S, R13E: sections 5, 8-10, 13-17, 20-28, 33-36, 6 (NE and SE 
quarters only) and 7 (NE and SE quarters only)
    T13S, R14E: sections 19-21, 26-35
    T14S, R13E: sections 1-3, 10-14, 23-25
    T14S, R14E: sections 3-9, 17-19, 30
    T17S, R19E
    T18S, R19E
    T20S, R14-15E
    (f) Maricopa County PM-10 Nonattainment Area (Phoenix Planning 
Area). (1) Plan for Attainment of the 24-hour PM-10 Standard--Maricopa 
County PM-10 Nonattainment Area (May, 1997) submitted by the Arizona 
Department of Environmental Quality on May 7, 1997.
    (i) The Administrator approves the provisions for implementing RACM 
and BACM for the significant source categories of disturbed cleared 
areas, earth moving, and industrial haul roads.
    (ii) The Administrator approves the attainment and reasonable 
further progress demonstrations for the Maryvale PM-10 monitoring site 
and Salt River PM-10 monitoring site.

[[Page 83]]

    (iii) The approvals in paragraphs (f)(1) (i) and (ii) of this 
section are applicable only to the plan identified in paragraph (f)(1) 
of this section and do not constitute the Administrator's final decision 
as to the State's full compliance with the requirements of Clean Air Act 
sections 189(a)(1)(C) and 189(b)(1)(B) for RACM and BACM and sections 
189(a)(1)(B), 189(b)(1)(A) and 189(c)(1) for attainment and reasonable 
further progress.
    (g) Pursuant to the Federal planning authority in section 110(c) of 
the Clean Air Act, the Administrator finds that the applicable 
implementation plan for the Maricopa County ozone nonattainment area 
demonstrates the 15 percent VOC rate of progress required under section 
182(b)(1)(A)(i).
[38 FR 33373, Dec. 3, 1973, as amended at 48 FR 254, Jan. 4, 1983; 51 FR 
3336, Jan. 27, 1986; 51 FR 33750, Sept. 23, 1986; 62 FR 41864, Aug. 4, 
1997; 63 FR 28904, May 27, 1998]



Sec. 52.124  Part D disapproval.

    (a) The following portions of the Arizona SIP are disapproved 
because they do not meet the requirements of Part D of the Clean Air 
Act.
    (1) The attainment demonstration, conformity and contingency 
portions of the 1987 Maricopa Association of Governments Carbon Monoxide 
Plan and 1988 Addendum.
    (2) The attainment demonstration and contingency portions of the 
1987 Carbon Monoxide State Implementation Plan Revision for the Tucson 
Air Planning Area.
    (b) Maricopa County PM-10 Nonattainment Area (Phoenix Planning 
Area). (1) Plan for Attainment of the 24-hour PM-10 Standard--Maricopa 
County PM-10 Nonattainment Area (May, 1997) submitted by the Arizona 
Department of Environmental Quality on May 7, 1997.
    (i) The Administrator disapproves the provisions for implementing 
RACM and BACM for the significant source categories of agricultural 
fields, agricultural aprons, vacant lands, unpaved parking lots, and 
unpaved roads.
    (ii) The Administrator disapproves the attainment and reasonable 
further progress demonstrations for the Gilbert PM-10 monitoring site 
and West Chandler PM-10 monitoring site.
    (iii) The disapprovals in paragraphs (f)(1) (i) and (ii) of this 
section are applicable only to the plan identified in paragraph (f)(1) 
of this section and do not constitute the Administrator's final decision 
as to the State's full compliance with the requirements of Clean Air Act 
sections 189(a)(1)(C) and 189(b)(1)(B) for RACM and BACM and sections 
189(a)(1)(B), 189(b)(1)(A) and 189(c)(1) for attainment and reasonable 
further progress. Therefore such disapprovals do not constitute state 
failures for the purpose of triggering sanctions under Sec. 179(a) of 
the Clean Air Act.
[56 FR 5478, Feb. 11, 1991, as amended at 62 FR 41864, Aug. 4, 1997]



Sec. 52.125  Control strategy and regulations: Sulfur oxides.

    (a)(1) The requirements of subpart G of this chapter are not met 
since the control strategy does not analyze the impact of smelter 
fugitive emissions on ambient air quality (except at Hayden, Arizona) in 
the Central Arizona Intrastate, the Pima Intrastate, and the Southeast 
Arizona Intrastate (Cochise and Greenlee counties) Regions. Arizona must 
submit these smelter fugitive emissions control strategies to EPA by 
August 1, 1984. In addition, the requirements of Sec. 51.281 of this 
chapter are not met since the plan does not require permanent control of 
fugitive smelter emissions necessary to attain and maintain the national 
standards for sulfur oxides. The control strategy for Hayden shows that 
these controls are required to attain and maintain the national 
standards, and the fugitive control strategy analyses required above may 
show that they are required for some or all of the other smelter towns 
in Arizona. Arizona must submit all fugitive emissions control 
regulations necessary to attain and maintain the national standards for 
sulfur oxides to EPA by August 1, 1984. Therefore, the control 
strategies and regulations for the six smelter areas in the Central 
Arizona Intrastate, the Pima Intrastate and the Southeast Arizona 
Intrastate (Cochise and Greenlee counties) Regions are incomplete due to 
Arizona's failure to address the fugitive emissions problems at copper 
smelters.

[[Page 84]]

    (2) Regulation 7-1-4.1 (copper smelters) of the Arizona Rules and 
Regulations for Air Pollution Control, as it pertains to existing copper 
smelters, is disapproved for the Central Arizona Intrastate, Pima 
Intrastate and Southeast Arizona Intrastate (Cochise and Greenlee 
counties) Regions.
    (b) The requirements of subpart G and Sec. 51.281 of this chapter 
are not met since the plan does not provide the degree of control 
necessary to attain and maintain the national standards for sulfur 
oxides in the Northern Arizona Intrastate Region. Th erefore, Regulation 
7-1-4.2(C) (fuel burning installations) of the Arizona Rules and 
Regulations for Air Pollution Control, as it pertains to existing 
sources, is disapproved in the Northern Arizona Intrastate Region for 
steam power generating instal lations having a total rated capacity 
equal to or greater than 6,500 million B.t.u. per hour.
    (c) Replacement regulation for Regulation 7-1-4.2(C) (Fossil fuel-
fired steam generators in the Northern Arizona Intrastate Region). (1) 
This paragraph is applicable to the fossil fuel-fired steam generating 
equipment designated as Units 1, 2, and 3 at the Navajo Power Plant in 
the Northern Arizona Intrastate Region (Sec. 81.270 of this chapter).
    (2) No owner or operator of the fossil fuel-fired steam generating 
equipment to which this paragraph is applicable shall discharge or cause 
the discharge of sulfur oxides into the atmosphere in excess of the 
amount prescribed by the following equations:

                         E=12,245 S or e=1,540 S

where:
E=Allowable sulfur oxides emissions (lb./hr.) from all affected units.
e=Allowable sulfur oxides emissions (gm./sec.) from all affected units.
S=Sulfur content, in percent by weight, prior to any pretreatment of the 
fuel being burned.

    (3) For the purposes of this paragraph:
    (i) E shall not exceed 21,270 lb./hr. (2,680 gm./sec.).
    (ii) If the sum of sulfur oxides emissions from Units 1, 2, and 3 
would be less than 3,780 lb./hr. (475 gm./sec.) without the use of 
emission control equipment, the requirements of paragraphs (2), (4)(i) 
and (5) of this paragraph (c), shall not apply for the period of time 
that the emissions remain below this level.
    (iii) The applicability of paragraph (c)(2)(ii) of this section may 
be determined through a sulfur balance utilizing the analyzed sulfur 
content of the fuel being burned and the total rate of fuel consumption 
in all affected units.
    (4)(i) No owner or operator of the fossil fuel-fired steam 
generating equipment subject to this paragraph shall discharge or cause 
the discharge of sulfur oxides into the atmosphere from any affected 
unit in excess of the amount prescribed by the following equations, 
except as provided in paragraph (3)(ii) of this paragraph (c).

             E1=0.333 E or e1=0.333 e

where:
E=Allowable sulfur oxides emissions (lb./hr.) from all affected units as 
determined pursuant to paragraph (2) of this paragraph.
e=Allowable sulfur oxides emissions (gm./sec.) from all affected units 
as determined pursuant to paragraph (2) of this paragraph (c).
E1=Allowable sulfur oxides emissions (lb./hr.) from each 
affected unit.
e1=Allowable sulfur oxides emissions (gm./sec.) from each 
affected unit.

    (ii) The owner or operator of the fossil fuel-fired steam generating 
equipment to which this paragraph is applicable may submit a request to 
redesignate the allowable emissions specified in paragraph (c)(4)(i) of 
this section. Such a request shall be submitted no later than December 
2, 1974, and shall demonstrate that sulfur oxides emissions on a total 
plant basis will not exceed those specified in paragraphs (2) and (3)(i) 
of this paragraph (c). Upon receipt and evaluation of such request, the 
Administrator shall consider such and if appropriate, redesignate the 
allowable emissions specified in paragraph (c)(4)(i) of this section.
    (5) All sulfur oxides control equipment at the fossil fuel-fired 
steam generating equipment to which this paragraph is applicable shall 
be operated at the maximum practicable efficiency at all times, without 
regard to the allowable sulfur oxides emissions, determined according to 
paragraph (2) or (3)

[[Page 85]]

of this paragraph (c), except as provided in paragraph (3)(ii) of this 
paragraph (c).
    (6) Compliance with this paragraph shall be in accordance with the 
provisions of Sec. 52.134(a).
    (7) The test methods and procedures used to determine compliance 
with this paragraph shall be those prescribed in Sec. 60.46(c)(2) and 
(c)(4) of this chapter. The test methods for determining the sulfur 
content of fuel shall be those specified in Sec. 60.45(c) and (d) of 
this chapter.
    (d)-(e) [Reserved]
    (f)(1) Paragraphs B through E of regulation 7-1-4.2 (R9-3-402) 
(Sulfur Emissions: Fuel Burning Installations) of the Arizona Air 
Pollution Control Regulations are disapproved because they could allow 
existing oil fired facilities to use dispersion dependent techniques 
alone as a means of attaining and maintaining the national ambient air 
quality standards. The regulation does not assure the attainment and 
maintenance of the national standards in a manner which is consistent 
with the intent of sections 110(a)(2)(B) and 123(a)(2) of the Clean Air 
Act.
    (2) The approval of paragraphs A and F of regulation 7-1-4.2 as to 
coal fired facilities does not apply to the Salt River Project 
Agricultural Improvement and Power District-Navajo Generating Station.
    (3) Paragraphs B through E of regulation 8-1-4.2 (Sulfur Emissions--
Fuel Burning Installations) of the Yuma County Air Pollution Control 
Regulations are disapproved because they could allow existing facilities 
to use dispersion dependent techniques alone as a means of attaining and 
maintaining the National Ambient Air Quality Standards. This regulation 
does not assure the attainment and maintenance of the national standards 
in a manner which is consistent with the intent of sections 
110(a)(2)(B)and 123(a)(2) of the Clean Air Act.
    (g) Section 3, Regulation 3 (Sulfur from Primary Copper Smelters) of 
the Mohave County Health Department Air Pollution Control Regulations 
and Regulation 7-3-2.1 (Copper Smelters) of the Pinal-Gila Counties Air 
Quality Control District are disapproved since Section 36-1706 of the 
Arizona Revised Statutes grants exclusive jurisdiction to the Arizona 
Department of Health Services and the State Hearing Board over all 
existing copper smelters.
    (1) The requirements of Sec. 51.13 of this chapter are not met since 
the plan does not demonstrate that the emission limitations applicable 
to existing fuel burning equipment producing electrical energy will 
provide for the attainment and maintenance of the national standards in 
the Pima Intrastate Region (Sec. 81.269 of this chapter).
    (2) Regulation II: Rule 7A--paragraphs 2 through 5, Emission 
Limitations Fuel Burning Equipment--Sulfur Dioxide, of the Rules and 
Regulations of the Pima County Air Pollution Control District are 
disapproved because they could allow existing facilities to use 
dispersion dependent techniques along as a means of attaining and 
maintaining the National Ambient Air Quality Standards. The regulation 
does not assure the attainment and maintenance of the national standards 
in a manner which is consistent with the intent of section 110(a)(2)(B) 
of the Clean Air Act.
[37 FR 15081, July 27, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.125, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.126  Control strategy and regulations: Particulate matter.

    (a) The requirements of subpart G and Sec. 51.281 of this chapter 
are not met since the plan does not provide the degree of control 
necessary to attain and maintain the national standards for particulate 
matter in Gila, Maricopa, Pima, Pinal, and Santa Cruz Counties. 
Therefore, Regulation 7-1-3.6 (process industries) of the Arizona Rules 
and Regulations for Air Pollution Control is disapproved for Gila, 
Maricopa, Pima, Pinal, and Santa Cruz Counties.
    (b) Replacement regulation for Regulation 7-1-3.6 of the Arizona 
Rules and Regulations for Air Pollution Control (Gila, Maricopa, Pima, 
Pinal, and Santa Cruz Counties). (1) No owner or operator of any 
stationary process source in Gila, Maricopa, Pima, Pinal, or Santa Cruz 
County shall discharge or cause the discharge of particulate matter into 
the atmosphere in excess of the hourly

[[Page 86]]

rate shown in the following table for the process weight rate identified 
for such source:

                          [In pounds per hour]
------------------------------------------------------------------------
                                                     Process
          Process weight rate             Emission    weight    Emission
                                            rate       rate       rate
------------------------------------------------------------------------
50.....................................       0.36     60,000      29.60
100....................................       0.55     80,000      31.19
500....................................       1.53    120,000      33.28
1,000..................................       2.25    160,000      34.85
5,000..................................       6.34    200,000      36.11
10,000.................................       9.73    400,000      40.35
20,000.................................      14.99  1,000,000      46.72
------------------------------------------------------------------------

    (2) Paragraph (b)(1) of this section shall not apply to 
incinerators, fuel burning installations, or Portland cement plants 
having a process weight rate in excess of 250,000 lb/h.
    (3) No owner or operator of a Portland cement plant in Gila, 
Maricopa, Pima, Pinal, or Santa Cruz County with a process weight rate 
in excess of 250,000 lb/hr shall discharge or cause the discharge of 
particulate matter into the atmosphere in excess of the amount specified 
in Sec. 60.62 of this chapter.
    (4) Compliance with this paragraph shall be in accordance with the 
provisions of Sec. 52.134(a).
    (5) The test methods and procedures used to determine compliance 
with this paragraph are set forth below. The methods referenced are 
contained in the appendix to part 60 of this chapter. Equivalent methods 
and procedures may be used if approved by the Administrator.
    (i) For each sampling repetition, the average concentration of 
particulate matter shall be determined by using method 5. Traversing 
during sampling by method 5 shall be according to method 1. The minimum 
sampling time shall be 2 hours and the minimum sampling volume shall be 
60 ft 3(1.70 m 3), corrected to standard 
conditions on a dry basis.
    (ii) The volumetric flow rate of the total effluent shall be 
determined by using method 2 and traversing according to method 1. Gas 
analysis shall be performed using the integrated sample technique of 
method 3, and moisture content shall be determined by the condenser 
technique of method 4.
    (iii) All tests shall be conducted while the source is operating at 
the maximum production or combustion rate at which such source will be 
operated. During the tests, the source shall burn fuels or combinations 
of fuels, use raw materials, and maintain process conditions 
representative of normal operation, and shall operate under such other 
relevant conditions as the Administrator shall specify.
    (c) The requirements of Sec. 51.281 of this chapter are not met 
since the plan does not contain regulations for Mohave and Yuma Counties 
in the Mohave-Yuma Intrastate Region or Pinal-Gila Counties in the 
Central Arizona Intrastate Region which provide enforceable and 
reproducible test procedures for the determination of compliance with 
the emission standards. Therefore paragraph C of section 3, regulation 2 
(Particulates: Other Sources) of the Mohave County Air Pollution Control 
Regulations, paragraph B of regulation 8-1-3.6 (Particulates--Process 
Industries) of the Yuma County Air Pollution Control Regulations, and 
paragraph C of regulation 7-3-1.4 (Particulate Emissions--Incineration) 
and paragraph F of regulation 7-3-1.7 (Particulate Emissions--Fuel 
Burning Equipment) of the Rules and Regulations for Pinal-Gila Counties 
Air Quality Control District are disapproved.
[37 FR 15081, July 27, 1972, as amended at 38 FR 12704, May 14, 1973; 43 
FR 53034, Nov. 15, 1978; 45 FR 67346, Oct. 10, 1980; 51 FR 40676, 40677, 
Nov. 7, 1986]



Secs. 52.127--52.128  [Reserved]



Sec. 52.129  Review of new sources and modifications.

    (a) [Reserved]
    (b) National standards not met. The requirements of Sec. 51.160(a) 
of this chapter are not met in the Pima Intrastate Region since the 
Rules and Regulations of the Pima County Air Pollution Control District 
are not adequate to prevent construction or modification of a source 
which would interfere with the attainment or maintenance of the national 
standards.
    (c) Regulation for review of new sources and modifications. (1) The 
requirements of this paragraph are applicable to any stationary source 
in the Pima Intrastate Region (Sec. 81.269 of this chapter), the 
construction or modification of

[[Page 87]]

which iscommenced after the effective date of this regulation.
    (2) No owner or operator shall commence construction or modification 
of any new source after the effective date of this regulation without 
first obtaining approval from the Administrator of the location of such 
source.
    (i) Application for approval to construct or modify shall be made on 
forms furnished by the Administrator, or by other means prescribed by 
the Administrator.
    (ii) A separate application is required for each source.
    (iii) Each application shall be signed by the applicant.
    (iv) Each application shall be accompanied by site information, 
stack data, and the nature and amount of emissions. Such information 
shall be sufficient to enable the Administrator to make any 
determination pursuant to paragraph (c)(3) of this section.
    (v) Any additional information, plans, specifications, evidence or 
documentation that the Administrator may require shall be furnished upon 
request.
    (3) No approval to construct or modify will be granted unless the 
applicant shows to the satisfaction of the Administrator that the source 
will not prevent or interfere with attainment or maintenance of any 
national standard.
    (4)(i) Within twenty (20) days after receipt of an application to 
construct, or any addition to such application, the Administrator shall 
advise the owner or operator of any deficiency in the information 
submitted in support of the application. In the event of such a 
deficiency, the date of receipt of the application for the purpose of 
paragraph (c)(4)(ii) of this section, shall be the date on which all 
required information is received by the Administrator.
    (ii) Within thirty (30) days after receipt of a complete 
application, the Administrator shall:
    (a) Make a preliminary determination whether the source should be 
approved, approved with conditions, or disapproved.
    (b) Make available in at least one location in each region in which 
the proposed source would be constructed, a copy of all materials 
submitted by the owner or operator, a copy of the Administrator's 
preliminary determination and a copy or summary of other materials, if 
any, considered by the Administrator in making his preliminary 
determination; and
    (c) Notify the public, by prominent advertisement in a newspaper of 
general circulation in each region in which the proposed source would be 
constructed, of the opportunity for written public comment on the 
information submitted by the owner or operator and the Administrator's 
preliminary determination on the approvability of the source.
    (iii) A copy of the notice required pursuant to this paragraph shall 
be sent to the applicant and to state and local air pollution control 
agencies, having cognizance over the location where the source will be 
situated.
    (iv) Public comments submitted in writing within thirty (30) days 
after the date such information is made available shall be considered by 
the Administrator in making his final decision on the application. No 
later than ten (10) days after the closeof the public comment period, 
the applicant may submit a written response to any comment submitted by 
the public. The Administrator shall consider the applicant's response in 
making his final decision. All comments shall be made available for 
public inspection in at least one location in the region in which the 
source would be located.
    (v) The Administrator shall take final action on an application 
within thirty (30) days after the close of the public comment period. 
The Administrator shall notify the applicant in writing of his approval, 
conditional approval, or denial of the application, and shall set forth 
his reasons for conditional approval or denial. Such notification shall 
be made available for public inspection in at least one location in the 
region in which the source would be located.
    (vi) The Administrator may extend each of the time periods specified 
in paragraph (c)(4) (ii), (iv) or (v) of this section by no more than 30 
days, or such other period as agreed to by the applicant and the 
Administrator.
    (5) The Administrator may cancel an approval if the construction is 
not begun within 2 years from the date of

[[Page 88]]

issuance, or if during the construction, work is suspended for 1 year.
    (6) Approval to construct or modify shall not relieve any owner or 
operator of the responsibility to comply with any local, State or 
Federal regulation which is part of the applicable plan.
    (7) Approval to construct or modify shall not be required for:
    (i) The installation or alteration of an air pollutant detector, air 
pollutants recorder, combustion controller, or combustion shutoff.
    (ii) Airconditioning or ventilating systems not designed to remove 
air pollutants generated by or released from equipment.
    (iii) Fuel burning equipment, other than smokehouse generators, 
which has a heat input of not more than 250 MBtu/h (62.5 billion g-cal/
h) and burns only gaseous fuel containing not more than 20.0 grain 
H2 S per 100 stdft 3 (45.8 g/100 stdm 
3); has a heat input of not more than 1 MBtu/h (250 Mg-cal/h) 
and burns only distillate oil; or has a heat input of not more than 
350,000 Btu/h (88.2 Mg-cal/h) and burns any other fuel.
    (iv) Mobile internal combustion engines.
    (v) Laboratory equipment used exclusively for chemical or physical 
analysis.
    (vi) Other sources of minor significance specified by the 
Administrator.
    (8) Any owner or operator who constructs, modifies, or operates a 
stationary source not in accordance with the application, as approved 
and conditioned by the Administrator, or any owner or operator of a 
stationary source subject to this paragraph who commences construction 
or modification without applying for and receiving approval hereunder, 
shall be subject to enforcement action under section 113 of the Act.
    (d) Regulation for review of new sources and modifications: Federal 
Regulations.
    (1) This requirement is applicable to any stationary source subject 
to the requirements of Sec. 52.126(b), the construction or modification 
of which is commenced after the effective date of this regulation.
    (2) No owner or operator shall commence construction or modification 
of any stationary source after the effective date of this regulation, 
without first obtaining approval from the Administrator of the location 
and design of such source.
    (i) Application for approval to construct or modify shall be made on 
forms furnished by the Administrator, or by other means prescribed by 
the Administrator.
    (ii) A separate application is required for each source.
    (iii) Each application shall be signed by the applicant.
    (iv) Each application shall be accompanied by site information, 
plans, descriptions, specifications, and drawings showing the design of 
the source, the nature and amount of emissions, and the manner in which 
it will be operated and controlled.
    (v) Any additional information, plans, specifications, evidence, or 
documentation that the Administrator may require shall be furnished upon 
request.
    (3) No approval to construct or modify will be granted unless the 
applicant shows to the satisfaction of the Administrator that the source 
will operate without causing a violation of Sec. 52.126(b).
    (4)(i) Within twenty (20) days after receipt of an application to 
construct, or any addition to such application, the Administrator shall 
advise the owner or operator of any deficiency in the information 
submitted in support of the application. In the event of such a 
deficiency, the date of receipt of the application for the purpose of 
paragraph (d)(4)(ii) of this section, shall be the date on which all 
required information is received by the Administrator.
    (ii) Within thirty (30) days after receipt of a complete 
application, the Administrator shall:
    (a) Make a preliminary determination whether the source should be 
approved, approved with conditions, or disapproved.
    (b) Make available in at least one location in each region in which 
the proposed source would be constructed, a copy of all materials 
submitted by the owner or operator, a copy of the Administrator's 
preliminary determination and a copy or summary of other materials, if 
any, considered by the Administrator in making his preliminary 
determination; and

[[Page 89]]

    (c) Notify the public, by prominent advertisement in a newspaper of 
general circulation in each region in which the proposed source would be 
constructed, of the opportunity for written public comment on the 
information submitted by the owner or operator and the Administrator's 
preliminary determination on the approvability of the source.
    (iii) A copy of the notice required pursuant to this paragraph shall 
be sent to the applicant and to state and local air pollution control 
agencies, having cognizance over the location where the source will be 
situated.
    (iv) Public comments submitted in writing within thirty (30) days 
after the date such information is made available shall be considered by 
the Administrator in making his final decision on the application. No 
later than ten (10) days after the close of the public comment period, 
the applicant may submit a written response to any comment submitted by 
the public. The Administrator shall consider the applicant's response in 
making his final decision. All comments shall be made available for 
public inspection in at least one location in the region in which the 
source would be located.
    (v) The Administrator shall take final action on an application 
within thirty (30) days after the close of the public comment period. 
The Administrator shall notify the applicant in writing of his approval, 
conditional approval, or denial of the application, and shall set forth 
his reasons for conditional approval or denial. Such notification shall 
be made available for public inspection in at least one location in the 
region in which the source would be located.
    (vi) The Administrator may extend each of the time periods specified 
in paragraph (d)(4)(ii), (iv) or (v) of this section by no more than 30 
days, or such other period as agreed to by the applicant and the 
Administrator.
    (5) The Administrator may impose any reasonable conditions upon an 
approval including conditions requiring the source to be provided with:
    (i) Sampling ports of a size, number, and location as the 
Administrator may require,
    (ii) Safe access to each port,
    (iii) Instrumentation to monitor and record emission data, and
    (iv) Any other sampling and testing facilities.
    (6) The Administrator may cancel an approval if the construction is 
not begun within 2 years from the date of issuance, or if during the 
construction, work is suspended for 1 year.
    (7) Any owner or operator subject to the provisions of this 
regulation shall furnish the Administrator written notification as 
follows:
    (i) A notification of the anticipated date of initial startup of 
source not more than 60 days or less than 30 days prior to such date.
    (ii) A notification of the actual date of initial startup of a 
source within 15 days after such date.
    (8) Within 60 days after achieving the maximum production rate at 
which the source will be operated but not later than 180 days after 
initial startup of such source, the owner or operator of such source 
shall conduct a performance test(s) in accordance with the methods and 
under operating conditions approved by the Administrator and furnish the 
Administrator a written report of the results of such performance test.
    (i) Such test shall be at the expense of the owner or operator.
    (ii) The Administrator may monitor such test and also may conduct 
performance tests.
    (iii) The owner or operator of a source shall provide the 
Administrator 15 days prior notice of the performance test to afford the 
Administrator the opportunity to have an observer present.
    (iv) The Administrator may waive the requirement for performance 
tests if the owner or operator of a source has demonstrated by other 
means to the Administrator's satisfaction that the source is being 
operated in compliance with the requirements of Sec. 52.126(b).
    (9) Approval to construct or modify shall not relieve the owner or 
operator of the responsibility to comply with all local, State, or 
Federal regulations which are part of the applicable plan.
    (10) Approval to construct or modify shall not be required for:

[[Page 90]]

    (i) The installation or alteration of an air pollutant detector, air 
pollutants recorder, combustion controller, or combustion shutoff.
    (ii) Air-conditioning or ventilating systems not designed to remove 
air pollutants generated by or released from equipment.
    (iii) Fuel burning equipment, other than smokehouse generators, 
which has a heat input of not more than 250 MBtu/h (62.5 billion g-cal/
h) and burns only gaseous fuel containing not more than 20.0 grain 
H2 S per 100 stdft 3 (45.8 g/100 stdm 
3); has a heat input of not more than 1 MBtu/h (250 Mg-cal/h) 
and burns only distillate oil; or has a heat input of not more than 
350,000 Btu/h (88.2 Mg-cal/h) and burns any other fuel.
    (iv) Mobile internal combustion engines.
    (v) Laboratory equipment used exclusively for chemical or physical 
analyses.
    (vi) Other sources of minor significance specified by the 
Administrator.
    (11) Any owner or operator who constructs, modifies, or operates a 
stationary source not in accordance with the application, as approved 
and conditioned by the Administrator, or any owner or operator of a 
stationary source subject to this paragraph who commences construction 
or modification without applying for and receiving approval hereunder, 
shall be subject to enforcement action under section 113 of the Act.
    (e) Delegation of authority. (1) The Administrator shall have the 
authority to delegate responsibility for implementing the procedures for 
conducting source review pursuant to this section in accordance with 
paragraphs (g) (2), (3), and (4) of this section.
    (2) Where the Administrator delegates the responsibility for 
implementing the procedures for conducting source review pursuant to 
this section to any Agency, other than a Regional Office of the 
Environmental Protection Agency, a copy of the notice pursuant to 
paragraphs (c)(4)(iii) and (d)(4)(iii) of this section shall be sent to 
the Administrator through the appropriate Regional Office.
    (3) In accordance with Executive Order 11752, the Administrator's 
authority for implementing the pro cedures  for  conducting  source  
review pursuant to this section shall not be delegated, other than to a 
Regional Office of the Environmental Protection Agency, for new or 
modified sources which are owned or operated by the Federal government 
or for new or modified sources located on Federal lands; except that, 
with respect to the latter category, where new or modified sources are 
constructed or operated on Federal lands pursuant to leasing or other 
Federal agreements, the Federal Land Manager may at his discretion, to 
the extent permissible under applicable statutes and regulations, 
require the lessee or permittee to be subject to new source review 
requirements which have been delegated to a state or local agency 
pursuant to this paragraph.
    (4) The Administrator's authority for implementing the procedures 
for conducting source review pursuant to this section shall not be 
redelegated, other than to a Regional Office of the Environmental 
Protection Agency, for new or modified sources which are located in 
Indian reservations except where the State has assumed jurisdiction over 
such land under other laws, in which case the Administrator may delegate 
his authority to the States in accordance with paragraphs (g)(2), (3), 
and (4) of this section.
[37 FR 15081, July 27, 1972, as amended at 38 FR 12705, May 14, 1973; 39 
FR 7279, Feb. 25, 1974; 39 FR 28285, Aug. 8, 1974; 40 FR 50268, Oct. 29, 
1975; 45 FR 67346, Oct. 10, 1980; 51 FR 40677, Nov. 7, 1986; 60 FR 
33922, June 29, 1995]



Sec. 52.130  Source surveillance.

    (a) The requirements of Sec. 51.211 of this chapter are not met 
since the plan does not contain legally enforceable procedures for 
requiring sources in the Northern Arizona, Mohave-Yuma, Central Arizona, 
and Southeast Arizona Intrastate Regions to maintain records of and 
periodically report on the nature and amounts of emissions.
    (b) The requirements of Sec. 51.213 of this chapter are not met 
because the plan does not provide procedures for obtaining and 
maintaining data on actual emission reductions achieved as a result of 
implementing transportation control measures.

[[Page 91]]

    (c) Regulation for source recordkeeping and reporting. (1) The owner 
or operator of any stationary source in the Northern Arizona, Mohave-
Yuma, Central Arizona, or Southeast Arizona Intrastate Region 
(Secs. 81.270, 81.268, 81.271, and 81.272 of this chapter) shall, upon 
notification from the Administrator, maintain records of the nature and 
amounts of emissions from such source or any other information as may be 
deemed necessary by the Administrator to determine whether such source 
is in compliance with applicable emission limitations or other control 
measures.
    (2) The information recorded shall be summarized and reported to the 
Administrator, and shall be submitted within 45 days after the end of 
the reporting period. Reporting periods are January 1 to June 30 and 
July 1 to December 31, except that the initial reporting period shall 
commence on the date the Administrator issues notification of the 
recordkeeping requirements.
    (3) Information recorded by the owner or operator and copies of the 
summarizing reports submitted to the Administrator shall be retained by 
the owner or operator for 2 years after the date on which the pertinent 
report is submitted.
    (4) Emission data obtained from owners or operators of stationary 
sources will be correlated with applicable emission limitations and 
other control measures. All such emission data will be available during 
normal business hours at the regional office (region IX). The 
Administrator will designate one or more places in Arizona where such 
emission data and correlations will be available for public inspection.
    (d) The requirements of Sec. 51.214 of this chapter are not met 
since the plan does not contain legally enforceable procedures for 
requiring certain stationary sources subject to emission standards to 
install, calibrate, operate, and maintain equipment for continuously 
monitoring and recording emissions, and to provide other information as 
specified in Appendix P of part 51 of this chapter.
    (e) The requirements of Sec. 51.214 of this chapter are not met 
since the plan does not provide sufficient regulations to meet the 
minimum specifications of Appendix P in the Maricopa Intrastate Region. 
Additionally, Maricopa County Air Pollution Control Regulation IV, rule 
41, paragraph B, sections 6.0-6.4 (Special Consideration) is disapproved 
since it does not contain the specific criteria for determining those 
physical limitations or extreme economic situations where alternative 
monitoring requirements would be applicable.
[37 FR 15081, July 27, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.130, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Secs. 52.131--52.132  [Reserved]



Sec. 52.133  Rules and regulations.

    (a) Regulation 7-1-1.4(A) (Exceptions) of the Arizona Rules and 
Regulations for Air Pollution Control, regulations 12-3-2 (Emission 
Standards) of the Coconino County Rules and Regulations for Air 
Pollution Control, section 3, regulation 5 (Exceptions) of the Mohave 
County Air Pollution Control Regulations, regulation 8-1-1.6 
(Exceptions) of the Yuma County Air Pollution Control Regulations, and 
regulation 7-1-2.8 (Exceptions) of the Rules and Regulations for Pinal-
Gila Counties Air Quality Control District all provide for an exemption 
from enforcement action if the violation is attributable to certain 
events. These events are too broad in scope and the source can obtain 
the exemption merely by reporting the occurrence. Therefore, the above 
regulations are disapproved since these regulations make all approved 
emission limiting regulations potentially unenforceable.
    (b) Paragraph E of regulation 7-1-1.3 (R9-3-103) (Air Pollution 
Prohibited) prohibits any person from causing ground level 
concentrations to exceed ambient standards outside the boundaries of 
this operation. This regulation could allow violations of ambient air 
quality standards to occur in areas to which the public has access, 
contrary to the requirements of section 110(a)(1) of the Clean Air Act. 
Therefore, paragraph E of regulation 7-1-1.3 (R9-3-103) of the Arizona 
Rules and Regulations for Air Pollution Control is disapproved.

[[Page 92]]

    (c) The requirements of subpart G and Sec. 51.281 of this chapter 
are not met since the plan does not provide any enforceable regulations 
and a demonstration that such regulations will cause the attainment and 
maintenance of national ambient air quality standards in Graham and 
Greenlee Counties.
    (d) Section 3, regulation 4 (Ground Level Concentrations) of the 
Mohave County Air Pollution Control Regulations, paragraph E of 
regulation 8-1-1.3 (Air Pollution Prohibited) of the Yuma County Air 
Pollution Control Regulations, and paragraph C of regulation 7-1-1.3 
(Air Pollution Prohibited) of the Rules and Regulations for Pinal-Gila 
Counties Air Quality Control District prohibits any person from causing 
ground level concentrations to exceed ambient standards outside the 
boundaries of hisoperation. These regulations could allow violations of 
ambient air quality standards to occur in areas to which the general 
public has access, contrary to the requirements of section 110(a)(1) of 
the Clean Air Act. Therefore, these regulations are disapproved.
[37 FR 15082, July 27, 1972, as amended at 43 FR 33247, July 31, 1978; 
43 FR 53035, Nov. 15, 1978; 51 FR 40676, 40677, Nov. 7, 1986]



Sec. 52.134  Compliance schedules.

    (a) Federal compliance schedule. (1) Except as provided in paragraph 
(a)(2) of this section, the owner or operator of any stationary source 
subject to Sec. 52.126(b) shall comply with such regulation on or before 
January 31, 1974. The owner or operator of the source subject to 
Sec. 52.125(c) shall comply with such regulation at initial start-up of 
such source unless a compliance schedule has been submitted pursuant to 
paragraph (a)(2) of this section.
    (i) Any owner or operator in compliance with Sec. 52.126(b) on the 
effective date of this regulation shall certify such compliance to the 
Administrator no later than 120 days following the effective date of 
this paragraph.
    (ii) Any owner or operator who achieves compliance with 
Sec. 52.125(c) or Sec. 52.126(b) after the effective date of this 
regulation shall certify such compliance to the Administrator within 5 
days of the date compliance is achieved.
    (2) Any owner or operator of the stationary source subject to 
Sec. 52.125(c) and paragraph (a)(1) of this section may, no later than 
July 23, 1973, submit to the Administrator for approval a proposed 
compliance schedule that demonstrates compliance with Sec. 52.125(c) as 
expeditiously as practicable but not later than July 31, 1977. Any owner 
or operator of a stationary source subject to Sec. 52.126(b) and 
paragraph (a)(1) of this section may, no later than 120 days following 
the effective date of this paragraph, submit to the Administrator for 
approval a proposed compliance schedule that demonstrates compliance 
with Sec. 52.126(b) as expeditiously as practicable but not later than 
July 31, 1975.
    (i) The compliance schedule shall provide for periodic increments of 
progress toward compliance. The dates for achievement of such increments 
shall be specified. Increments of progress shall include, but not be 
limited to: Submittal of the final control plan to the Administrator; 
letting of necessary contracts for construction or process change, or 
issuance of orders for the purchase of component parts to accomplish 
emission control equipment or process modification; completion of onsite 
construction or installation of emission control equipment or process 
modification; and final compliance.
    (ii) Any compliance schedule for the stationary source subject to 
Sec. 52.125(c) which extends beyond July 31, 1975, shall apply any 
reasonable interim measures of control designed to reduce the impact of 
such source on public health.
    (3) Any owner or operator who submits a compliance schedule pursuant 
to this paragraph shall, within 5 days after the deadline for each 
increment of progress, certify to the Administrator whether or not the 
required increment of the approved compliance schedule has been met.
[38 FR 12705, May 14, 1973, as amended at 39 FR 10584, Mar. 21, 1974; 39 
FR 43277, Dec. 12, 1974; 40 FR 3994, Jan. 27, 1975; 54 FR 25258, June 
14, 1989]



Sec. 52.135  Resources.

    (a) The requirements of Sec. 51.280 of this chapter are not met 
because the transportation control plan does not contain

[[Page 93]]

a sufficient description of resources available to the State and local 
agencies and of additional resources needed to carry out the plan during 
the 5-year period following submittal.
[38 FR 16564, June 22, 1973, as amended at 51 FR 40677, Nov. 7, 1986]



Sec. 52.136  Control strategy for ozone: Oxides of nitrogen.

    EPA is approving an exemption request submitted by the State of 
Arizona on April 13, 1994 for the Maricopa County ozone nonattainment 
area from the NOX RACT requirements contained in section 
182(f) of the Clean Air Act. This approval exempts the Phoenix area from 
implementing the NOX requirements for RACT, new source review 
(NSR), and the applicable general and transportation conformity and 
inspection and maintenance (I/M) requirements of the CAA. The exemption 
is based on Urban Airshed Modeling as lasts for only as long as the 
area's modeling continues to demonstrate attainment without 
NOX reductions from major stationary sources.
[60 FR 19515, Apr. 19, 1995]



Sec. 52.137  [Reserved]



Sec. 52.138  Conformity procedures.

    (a) Purpose. The purpose of this regulation is to provide procedures 
as part of the Arizona carbon monixide implementation plans for 
metropolitan transportation planning organizations (MPOs) to use when 
determining conformity of transportationplans, programs, and projects. 
Section 176(c) of the Clean Air Act (42 U.S.C. 7506(c)) prohibits MPOs 
from approving any project, program, or plan which does not conform to 
an implementation plan approved or promulgated under section 110.
    (b) Definitions.
    (1) Applicable implementation plan or applicable plan means the 
portion (or portions) of the implementation plan, or most recent 
revision thereof, which has been approved under section 110 of the Clean 
Air Act, 42 U.S.C. 7410, or promulgated under section 110(c) of the CAA, 
42 U.S.C. 7410(c).
    (2) Carbon monoxide national ambient air quality standard (CO NAAQS) 
means the standards for carbon monoxide promulgated by the Administrator 
under section 109, 42 U.S.C. 7409, of the Clean Air Act and found in 40 
CFR 50.8
    (3) Cause means resulting in a violation of the CO NAAQS in an area 
which previously did not have ambient CO concentrations above the CO 
NAAQS.
    (4) Contribute means resulting in measurably higher average 8-hour 
ambient CO concentrations over the NAAQS or an increased number of 
violations of the NAAQS in an area which currently experiences CO levels 
above the standard.
    (5) Metropolitan planning organization (MPO) means the organization 
designated under 23 U.S.C. 134 and 23 CFR part 450.106. For the specific 
purposes of this regulation, MPO means either the Maricopa Association 
of Governments or the Pima Association of Governments.
    (6) Nonattainment area means for the specific purpose of this 
regulation either the Pima County carbon monoxide nonattainment area as 
described in 40 CFR 81.303 or the Maricopa County carbon monoxide 
nonattainment area as described in 40 CFR 81.303 (i.e., the MAG urban 
planning area).
    (7) Transportation control measure (TCM) means any measure in an 
applicable implementation plan which is intended to reduce emissions 
from transportation sources.
    (8) Transportation improvement program (TIP) means the staged 
multiyear program of transportation improvements including an annual (or 
biennial) element which is required in 23 CFR part 450.
    (9) Unified planning work program or UPWP means the program required 
by 23 CFR 450.108(c) and endorsed by the metropolitan planning 
organization which describes urban transportation and transportation-
related planning activities anticipated in the area during the next 1- 
to 2-year period including the planning work to be performed with 
federal planning assistance and with funds available under the Urban 
Mass Transportation Act (49 U.S.C.) section 9 or 9A. UPWPs are also 
known as overallwork programs or OWPs.
    (c) Applicability. These procedures shall apply only to the Maricopa 
Association of Governments in its role as the designated metropolitan 
planning

[[Page 94]]

organization for Maricopa County, Arizona, and the Pima Association of 
Governments in its role as the designated metropolitan planning 
organization for Pima County, Arizona.
    (d) Procedures.
    (1) Transportation Plans and Transportation Improvement Programs.
    (i) Documentation. The MPO shall prepare for each transportation 
plan and program (except for the unified planning work program), as part 
of the plan or program, a report documenting for each plan and program 
the following information:
    (A) the disaggregated population projections and employment which 
were assumed in:
    (1) the applicable plan, and
    (2) the transportation plan/program;
    (B) the levels of vehicle trips, vehicle miles traveled, and 
congestion that were:
    (1) assumed in the applicable plan, and
    (2) expected to result from the implementation of the plan/program 
over the period covered by the applicable plan considering any growth 
likely to result from the implementation of the plan/program;
    (C) for each major transportation control measure in the applicable 
implementation plan;
    (1) the TCM's implementation schedule and, if determined in the 
applicable plan, expected effectiveness in reducing CO emissions,
    (2) the TCM's current implementation status and, if feasible, its 
current effectiveness in reducing CO emissions, and
    (3) actions in the plan/program which may beneficially or adversely 
affect the implementation and/or effectiveness of the TCM;
    (D) the CO emission levels resulting from the implementation of the 
plan/program over the period covered by the applicable plan considering 
any growth likely to result from the implementation of the plan/program; 
and
    (E) the ambient CO concentration levels, micro-scale and regional, 
resulting from the implementation of the plan/program over the period 
covered by the applicable plan considering any growth likely to result 
from the implementation of the plan or program.
    (ii) Findings. Prior to approving a transportation plan/program, the 
MPO shall determine if the plan/program conforms to the applicable 
implementation plan. In making this determination, the MPO shall make 
and support each of the following findings for each transportation plan 
and program using the information documented in paragraph (d)(1)(i) of 
this section:
    (A) that implementation of the transportation plan/program will 
provide for the implementation of TCMs in the applicable plan on the 
schedule set forth in the applicable plan;
    (B) that CO emission levels, microscale and regional, resulting from 
the implementation of the plan/program will not delay attainment or 
achievement of any interim emission reductions needed for attainment 
and/or interfere with maintenance of the CONAAQS throughout the 
nonattainment area during the period covered by the applicable plan; and
    (C) that implementation of the plan/program would not cause or 
contribute to a violation of the CO NAAQS anywhere within the 
nonattainment area during the period covered by the applicable plan.
    (2) Amendments to a Transportation Plan or Transportation 
Implementation Program. Prior to approving any amendment to a 
transportation plan or program, the MPO shall first determine that the 
amendment does not substantially change the information provided under 
paragraph (d)(1)(i) of this section and does not change the findings in 
paragraph (d)(1)(ii) of this section with respect to the original plan 
or program.
    (3) Transportation Projects. As part of any individual 
transportation project approval made by the MPO, the MPO shall determine 
whether the project conforms to the applicable implementation plan using 
the following procedure:
    (i) For projects from a plan and TIP that has been found to conform 
under procedures in paragraph (d)(1) of this section within the last 
three years or from a Plan or TIP amendment that has been found to 
conform under procedures in paragraph (d)(2) of this section in the past 
three years, the MPO shall

[[Page 95]]

document as part of the approval document:
    (A) the TIP project number;
    (B) whether the project is an exempt project as defined in paragraph 
(e) of this section; and
    (C) whether the design and scope of the project has changed 
significantly from the design and scope of the project as described in 
the conforming TIP:
    (1) If the design and scope of the project has not changed 
significantly, the MPO may find the project conforming; or
    (2) If the design and scope of the project has changed significantly 
or the design and scope of the project could not be determined from the 
TIP, the MPO shall use the procedures in paragraph (d)(3)(ii) of this 
section to determine if the project conforms to the applicable 
implementation plan.
    (ii) For projects not exempted under paragraph (e) of this section 
and not in a plan or a TIP that has been found to conform under 
procedures in paragraph (d)(1) of this section within the last three 
years:
    (A) Documentation. The MPO shall document as part of the approval 
document for each such project:
    (1) the disaggregated population and employment projections, to the 
extent they are used in
    (i) the applicable plan, and
    (ii) designing and scoping the project;
    (2) the levels of vehicle trips, vehicle miles traveled, and 
congestion that are
    (i) assumed in the applicable plan, and
    (ii) expected to result over the period covered by the applicable 
plan from the construction of the project considering any growth likely 
to result from the project;
    (3) for each transportation control measure in the applicable plan 
likely to be affected by the project:
    (i) its implementation schedule and expected emission reduction 
effectiveness from the applicable plan,
    (ii) its current implementation status and, if feasible, its current 
effectiveness, and
    (iii) any actions as part of the project which may beneficially or 
adversely affect the implementation and/or effectiveness of the TCM;
    (4) CO emission levels which will result from the project over the 
period covered by the applicable plan considering any growth likely to 
result from the project; and
    (5) ambient CO concentration levels which will result from the 
project over the period covered by the applicable plan considering any 
growth likely to result from the project.
    (B) Findings. Prior to approving any transportation project, the MPO 
shall determine if the project conforms to the applicable implementation 
plan. In making this determination, the MPO shall make and support the 
following findings for each project using the information documented in 
paragraph (d)(2)(ii)(A) of this section:
    (1) that the project will provide for the implementation of TCMs 
affected by the project on the schedule set forth in the applicable 
plan;
    (2) that CO emission levels, microscale and regional, resulting from 
the implementation of the project during the period covered by the 
applicable plan will not delay attainment or any required interim 
emission reductions and/or interfere with maintenance of the CO NAAQS in 
an area substantially affected by the project;
    (3) that the project will not cause or contribute to a violation of 
the CO NAAQS during the period covered by the applicable plan near the 
project; and
    (4) that the projected emissions from the project, when considered 
together with emissions projected for the conforming plan and program 
within the nonattainment area, do not cause the plan and program to 
exceed the emission reduction projections and schedules assigned to such 
plans and programs in the applicable implementation plan.
    (e) Exempt Projects.
    An individual project is exempt from the requirements of paragraph 
(d) of this section if it is:
    (1) located completely outside the nonattainment area;
    (2) a safety project which is included in the statewide safety 
improvement program, will not alter the functional

[[Page 96]]

traffic capacity or capability of the facility being improved, and does 
not adversely affect the TCMs in the applicable plan;
    (3) a transportation control measure from the approved applicable 
plan; or
    (4) a mass transit project funded under the Urban Mass 
Transportation Act, 49 U.S.C.
[56 FR 5485, Feb. 11, 1991]



Sec. 52.139  [Reserved]



Sec. 52.140  Monitoring transportation   trends.

    (a) This section is applicable to the State of Arizona.
    (b) In order to assure the effectiveness of the inspection and 
maintenance program and the retrofit devices required under the Arizona 
implementation plan, the State shall monitor the actual per-vehicle 
emissions reductions occurring as a result of such measures. All data 
obtained from such monitoring shall be included in the quarterly report 
submitted to the Administrator by the State in accordance with 
Sec. 58.35 of this chapter. The first quarterly report shall cover the 
period January 1 to March 31, 1976.
    (c) In order to assure the effective implementation of Secs. 52.137, 
52.138, and 52.139, the State shall monitor vehicle miles traveled and 
average vehicle speeds for each area in which such sections are in 
effect and during such time periods as may be appropriate to evaluate 
the effectiveness of such a program. All data obtained from such 
monitoring shall be included in the quarterly report submitted to the 
Administrator by the State of Arizona in accordance with Sec. 58.35 of 
this chapter. The first quarterly report shall cover the period from 
July 1 to September 30, 1974. The vehicle miles traveled and vehicle 
speed data shall be collected on a monthly basis and submitted in a 
format similar to Table 1.

                                 Table 1
Time period . . . ......................................................
Affected area . . . ........................................


------------------------------------------------------------------------
                                                  VMT or average vehicle
                                                           speed
                                                 -----------------------
                  Roadway type                                  Vehicle
                                                    Vehicle    type (2)
                                                   type (1)       \1\
------------------------------------------------------------------------
Freeway.........................................
Arterial........................................
Collector.......................................
Local...........................................
------------------------------------------------------------------------
\1\ Continue with other vehicle types as appropriate.

    (d) No later than March 1, 1974, the State shall submit to the 
Administrator a compliance schedule to implement this section. The 
program description shall include the following:
    (1) The agency or agencies responsible for conducting, overseeing, 
and maintaining the monitoring program.
    (2) The administrative procedures to be used.
    (3) A description of the methods to be used to collect the emission 
data, VMT data, and vehicle speed data; a description of the 
geographical area to which the data apply; identification of the 
location at which the data will be collected; and the time periods 
during which the data will be collected.
    (e) The quarterly reports specified in paragraphs (b) and (c) of 
this section shall be submitted to the Administrator through the 
Regional Office, and shall be due within 45 days after the end of each 
reporting period.
[38 FR 33376, Dec. 3, 1973, as amended at 39 FR 32113, Sept. 5, 1974; 44 
FR 27571, May 10, 1979]



Secs. 52.141--52.143  [Reserved]



Sec. 52.144  Significant deterioration of air quality.

    (a) The requirements of sections 160 through 165 of the Clean Act 
are not met, since the plan as it applies to stationary sources under 
the jurisdiction of the Pima County Health Department and the Maricopa 
County Department of Health Services and stationary sources locating on 
Indian lands does not include approvable procedures for preventing the 
significant deterioration of air quality.
    (b) Regulation for preventing significant deterioration of air 
quality. The provisions of Sec. 52.21 (b) through (w) are hereby 
incorporated and made a part of the applicable State plan for the State 
of Arizona for that portion applicable

[[Page 97]]

to the Pima County Health Department and the Maricopa County Department 
of Health Services and sources locating on Indian lands.
[48 FR 19879, May 3, 1983]



Sec. 52.145  Visibility protection.

    (a) The requirements of section 169A of the Clean Air Act are not 
met, because the plan does not include approvable procedures for 
protection of visibility in mandatory Class I Federal areas.
    (b) Regulations for visibility monitoring and new source review. The 
provisions of Secs. 52.26, 52.27 and 52.28, are hereby incorporated and 
made part of the applicable plan for the State of Arizona.
    (c) Long-term strategy. The provisions of Sec. 52.29 are hereby 
incorporated and made part of the applicable plan for the State of 
Arizona.
    (d) This paragraph is applicable to the fossil fuel-fired, steam-
generating equipment designated as Units 1, 2, and 3 at the Navajo 
Generating Station in the Northern Arizona Intrastate Air Quality 
Control Region (Sec. 81.270 of this chapter).
    (1) Definitions.
    Administrator means the Administrator of EPA or his/her designee.
    Affected Unit(s) means the steam-generating unit(s) at the Navajo 
Generating Station, all of which are subject to the emission limitation 
in paragraph (d)(2) of this section, that has accumulated at least 365 
boiler operating days since the passage of the date defined in paragraph 
(d)(6) of this section applicable to it.
    Boiler Operating Day for each of the boiler units at the Navajo 
Generating Station is defined as a 24-hour calendar day (the period of 
time between 12:01 a.m. and 12:00 midnight in Page, Arizona) during 
which coal is combusted in that unit for the entire 24 hours.
    Owner or Operator means the owner, participant in, or operator of 
the Navajo Generating Station to which this paragraph is applicable.
    Unit-Week of Maintenance means a period of 7 days during which a 
fossil fuel-fired steam-generating unit is under repair, and no coal is 
combusted in the unit.
    (2) Emission limitation. No owner or operator shall discharge or 
cause the discharge of sulfur oxides into the atmosphere in excess of 42 
ng/J [0.10 pound per million British thermal units (lb/MMBtu)] heat 
input.
    (3) Compliance determination. Until at least one unit qualifies as 
an affected unit, no compliance determination is appropriate. As each 
unit qualifies for treatment as an affected unit, it shall be included 
in the compliance determination. Compliance with this emission limit 
shall be determined daily on a plant-wide rolling annual basis as 
follows:
    (i) For each boiler operating day at each steam generating unit 
subject to the emission limitation in paragraph (d)(2) of this section, 
the owner or operator shall record the unit's hourly SO2 
emissions using the data from the continuous emission monitoring 
systems, [required in paragraph (d)(4) of this section] and the daily 
electric energy generated by the unit (in megawatt-hours) as measured by 
the megawatt-hour meter for the unit.
    (ii) Compute the average daily SO2 emission rate in ng/J 
(lb/MMBtu) following the procedures set out in method 19, appendix A, 40 
CFR part 60 in effect on October 3, 1991.
    (iii) For each boiler operating day for each affected unit, 
calculate the product of the daily SO2 emission rate 
(computed according to paragraph (d)(3)(ii) of this section) and the 
daily electric energy generated (recorded according to paragraph 
(d)(3)(i) of this section) for each unit.
    (iv) For each affected unit, identify the previous 365 boiler 
operating days to be used in the compliance determination. Except as 
provided in paragraphs (d)(9) and (d)(10) of this section, all of the 
immediately preceding 365 boiler operating days will be used for 
compliance determinations.
    (v) Sum, for all affected units, the products of the daily 
SO2 emission rate-electric energy generated (as calculated 
according to paragraph (d)(3)(iii) of this section) for the boiler 
operating days identified in paragraph (d)(3)(iv) of this section.
    (vi) Sum, for all affected units, the daily electric energy 
generated (recorded according to paragraph (d)(3)(i)

[[Page 98]]

of this section) for the boiler operating days identified in paragraph 
(d)(3)(iv) of this section.
    (vii) Calculate the weighted plant-wide annual average 
SO2 emission rate by dividing the sum of the products 
determined according to paragraph (d)(3)(v) of this section by the sum 
of the electric energy generated determined according to paragraph 
(d)(3)(vi) of this section.
    (viii) The weighted plant-wide annual average SO2 
emission rate shall be used to determine compliance with the emission 
limitation in paragraph (d)(2) of this section.
    (4) Continuous emission monitoring. The owner or operator shall 
install, maintain, and operate continuous emission monitoring systems to 
determine compliance with the emission limitation in paragraph (d)(2) of 
this section as calculated in paragraph (d)(3) of this section. This 
equipment shall meet the specifications in appendix B of 40 CFR part 60 
in effect on October 3, 1991. The owner or operator shall comply with 
the quality assurance procedures for continuous emission monitoring 
systems found in appendix F of 40 CFR part 60 in effect on October 3, 
1991.
    (5) Reporting requirements. For each steam generating unit subject 
to the emission limitation in paragraph (d)(2) of this section, the 
owner or operator:
    (i) Shall furnish the Administrator written notification of the 
SO2, oxygen, and carbon dioxide emissions according to the 
procedures found in 40 CFR Sec. 60.7 in effect on October 3, 1991.
    (ii) Shall furnish the Administrator written notification of the 
daily electric energy generated in megawatt-hours.
    (iii) Shall maintain records according to the procedures in 40 CFR 
60.7 in effect on October 3, 1991.
    (iv) Shall notify the Administrator by telephone or in writing 
within one business day of any outage of the control system needed for 
compliance with the emission limitation in paragraph (d)(2) of this 
section and shall submit a follow-up written report within 30 days of 
the repairs stating how the repairs were accomplished and justifying the 
amount of time taken for the repairs.
    (6) Compliance dates. The requirements of this paragraph shall be 
applicable to one unit at the Navajo Generating Station beginning 
November 19, 1997, to two units beginning November 19, 1998, and to all 
units beginning on August 19, 1999.
    (7) Schedule of compliance. The owner or operator shall take the 
following actions by the dates specified:
    (i) By June 1, 1992, award binding contracts to an architectural and 
engineering firm to design and procure the control system needed for 
compliance with the emission limitation in paragraph (d)(2) of this 
section.
    (ii) By January 1, 1995, initiate on-site construction or 
installation of a control system for the first unit.
    (iii) By May 1, 1997, initiate start-up testing of the control 
system for the first unit.
    (iv) By May 1, 1998, initiate start-up testing of the control system 
for the second unit.
    (v) By February 1, 1999, initiate start-up testing of the control 
system for the third unit.

The interim deadlines will be extended if the owner or operators can 
demonstrate to the Administrator that compliance with the deadlines in 
paragraph (d)(6) of this section will not be affected.
    (8) Reporting on compliance schedule. Within 30 days after the 
specified date for each deadline in the schedule of compliance 
(paragraph (d)(7) of this section, the owner or operator shall notify 
the Administrator in writing whether the deadline was met. If it was not 
met the notice shall include an explanation why it was not met and the 
steps which shall be taken to ensure future deadlines will be met.
    (9) Exclusion for equipment failure during initial operation. For 
each unit, in determining compliance for the first year that such unit 
is required to meet the emission limitation in paragraph (d)(2) of this 
section, periods during which one of the following conditions are met 
shall be excluded:
    (i) Equipment or systems do not meet designer's or manufacturer's 
performance expectations.
    (ii) Field installation including engineering or construction 
precludes

[[Page 99]]

equipment or systems from performing as designed.

The periods to be excluded shall be determined by the Administrator 
based on the periodic reports of compliance with the emission limitation 
in paragraph (d)(2) of this section which shall identify the times 
proposed for exclusion and provide the reasons for the exclusion, 
including the reasons for the control system outage. The report also 
shall describe the actions taken to avoid the outage, to minimize its 
duration, and to reduce SO2 emissions at the plant to the 
extent practicable while the control system was not fully operational. 
Whenever the time to be excluded exceeds a cumulative total of 30 days 
for any control system for any affected unit, the owner or operators 
shall submit a report within 15 days addressing the history of and 
prognosis for the performance of the control system.
    (10) Exclusion for catastrophic failure. In addition to the 
exclusion of periods allowed in paragraph (d)(9) of this section, any 
periods of emissions from an affected unit for which the Administrator 
finds that the control equipment or system for such unit is out of 
service because of catastrophic failure of the control system which 
occurred for reasons beyond the control of the owner or operators and 
could not have been prevented by good engineering practices will be 
excluded from the compliance determination. Events which are the 
consequence of lack of appropriate maintenance or of intentional or 
negligent conduct or omissions of the owner or operators or the control 
system design, construction, or operating contractors do not constitute 
catastrophic failure.
    (11) Equipment operation. The owner or operator shall optimally 
operate all equipment or systems needed to comply with the requirements 
of this paragraph consistent with good engineering practices to keep 
emissions at or below the emission limitation in paragraph (d)(2) of 
this section, and following outages of any control equipment or systems 
the control equipment or system will be returned to full operation as 
expeditiously as practicable.
    (12) Maintenance scheduling. On March 16 of each year starting in 
1993, the owner or operator shall prepare and submit to the 
Administrator a long-term maintenance plan for the Navajo Generating 
Station which accommodates the maintenance requirements for the other 
generating facilities on the Navajo Generating Station grid covering the 
period from March 16 to March 15 of the next year and showing at least 6 
unit-weeks of maintenance for the Navajo Generating Station during the 
November 1 to March 15 period, except as provided in paragraph (d)(13) 
of this section. This plan shall be developed consistent with the 
criteria established by the Western States Coordinating Council of the 
North American Electric Reliability Council to ensure an adequate 
reserve margin of electric generating capacity. At the time that a plan 
is transmitted to the Administrator, the owner or operator shall notify 
the Administrator in writing if less than the full scheduled unit-weeks 
of maintenance were conducted for the period covered by the previous 
plan and shall furnish a written report stating how that year qualified 
for one of the exceptions identified in paragraph (d)(13) of this 
section.
    (13) Exceptions for maintenance scheduling. The owner or operator 
shall conduct a full 6 unit-weeks of maintenance in accordance with the 
plan required in paragraph (d)(12) of this section unless the owner or 
operator can demonstrate to the satisfaction of the Administrator that a 
full 6 unit-weeks of maintenance during the November 1 to March 15 
period should not be required because of the following:
    (i) There is no need for 6 unit-weeks of scheduled periodic 
maintenance in the year covered by the plan;
    (ii) The reserve margin on any electrical system served by the 
Navajo Generating Station would fall to an inadequate level, as defined 
by the criteria referred to in paragraph (d)(12) of this section.
    (iii) The cost of compliance with this requirement would be 
excessive. The cost of compliance would be excessive when the economic 
savings to the owner or operator of moving maintenance out of the 
November 1 to March 15 period exceeds $50,000 per unit-day of 
maintenance moved.

[[Page 100]]

    (iv) A major forced outage at a unit occurs outside of the November 
1 to March 15 period, and necessary periodic maintenance occurs during 
the period of forced outage.

If the Administrator determines that a full 6 unit-weeks of maintenance 
during the November 1 to March 15 period should not be required, the 
owner or operator shall nevertheless conduct that amount of scheduled 
maintenance that is not precluded by the Administrator. Generally, the 
owner or operator shall make best efforts to conduct as much scheduled 
maintenance as practicable during the November 1 to March 15 period.
[50 FR 28553, July 12, 1985, as amended at 52 FR 45137, Nov. 24, 1987; 
56 FR 50186, Oct. 3, 1991; 61 FR 14975, Apr. 4, 1996]



Sec. 52.146  Particulate matter (PM-10) Group II SIP commitments.

    (a) On December 28, 1988, the Governor's designee for Arizona 
submitted a revision to the State Implementation Plan (SIP) for Casa 
Grande, Show Low, Safford, Flagstaff and Joseph City, that contains 
commitments, from the Director of the Arizona Department of 
Environmental Quality, for implementing all of the required activities 
including monitoring, reporting, emission inventory, and other tasks 
that may be necessary to satisfy the requirements of the PM-10 Group II 
SIPs.
    (b) The Arizona Department of Environmental Quality has committed to 
comply with the PM-10 Group II State Implementation Plan (SIP) 
requirements for Casa Grande, Show Low, Safford, Flagstaff and Joseph 
City as provided in the PM-10 Group II SIPs for these areas.
    (c) On December 28, 1988, the Governor's designee for Arizona 
submitted a revision to the State Implementation Plan (SIP) for Ajo, 
that contains commitments from the Director of the Arizona Department of 
Environmental Quality, for implementing all of the required activities 
including monitoring, reporting, emission inventory, and other tasks 
that may be necessary to satisfy the requirements of the PM-10 Group II 
SIPs.
    (d) The Arizona Department of Environmental Quality has committed to 
comply with the PM-10 Group II State Implementation Plan (SIP) 
requirements.
[55 FR 17437, Apr. 25, 1990 and 55 FR 18108, May 1, 1990]



Sec. 52.150  Yavapai-Apache Reservation.

    (a) The provisions for prevention of significant deterioration of 
air quality at 40 CFR 52.21 are applicable to the Yavapai-Apache 
Reservation, pursuant to Sec. 52.21(a).
    (b) In accordance with section 164 of the Clean Air Act and the 
provisions of 40 CFR 52.21(g), the Yavapai-Apache Indian Reservation is 
designated as a Class I area for the purposes of preventing significant 
deterioration of air quality.
[61 FR 56470, Nov. 1, 1996]



                           Subpart E--Arkansas



Sec. 52.170  Identification of plan.

    (a) Title of plan: ``Arkansas Plan of Implementation for Air 
Pollution Control.''
    (b) The plan was officially submitted on January 28, 1972.
    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) A certification that the public hearings on the plan were held 
was submitted by the State Department of Pollution Control and Ecology 
on January 25, 1972. (Non-regulatory)
    (2) State Department of Pollution Control and Ecology letter 
outlining projected emission reductions, ASA forecasts, source 
surveillance, legal authority and interstate cooperation was submitted 
on February 24, 1972. (Non-regulatory)
    (3) Revision of section 16 of the State air code was submitted by 
the Department of Pollution Control and Ecology on July 7, 1972.
    (4) June 27, 1975, letter from the Governor submitting sections 1 
through 10 of the Regulations and Strategy of the Arkansas Plan of 
Implementation for Air Pollution Control except those portions relating 
to delegation of authority to enforce Federal requirements.
    (5) August 16, 1976, statement issued by Director of the Arkansas 
Department of Pollution Control and Ecology

[[Page 101]]

specifying the test and reference methods for determining compliance 
with emission limitations.
    (6) Administrative changes to the Arkansas Air Quality Surveillance 
Network were submitted by the Arkansas Department of Pollution Control 
and Ecology on February 15, 1977, January 10, 1978, and March 27, 1978. 
(Non-regulatory.)
    (7) On April 4, 1979, the Governor submitted the nonattainment area 
plan for the area designated nonattainment as of March 3, 1978.
    (8) On August 14, 1979, the Governor submitted supplemental 
information clarifying the plan.
    (9) Revisions to Arkansas Regulation 4.5(a) for the ``Control of 
Volatile Organic Compounds'' showing a final compliance date of June 1, 
1981, was submitted by the Arkansas Governor on December 10, 1979.
    (10) A modification to the definition for lowest achievable emission 
rate (LAER), consistent with the definition contained in section 171(3) 
of the Act, was submitted by the Arkansas Governor on December 10, 1979.
    (11) On July 11, 1979, the Governor submitted revisions to section 
6(a) malfunction or upset and section 7(e) continuous emission 
monitoring of the Arkansas Regulations.
    (12) Revisions to section 3 (i.e., 3.(a), (b), (k), (l), (n), (o), 
(z), (bb), (dd), (ee), (ff), and (gg)), section 4 (i.e., 4.1(b), 4.2(a), 
4.5(a)(1), 4.5(a)(2), 4.6(c), and 4.6(d)), and section 5 (i.e., 5.4 and 
5.5) were adopted by the Arkansas Commission on Pollution Control and 
Ecology on September 26, 1980 and submitted by the Governor on October 
10, 1980.
    (13) Revisions to section 3 (i.e., 3.(ii) through 3.(nn)), section 4 
(i.e., 4.1, 4.5(a)(1), 4.5(a)(2), and 4.6(e)), and section 5 (i.e., 5.6) 
of the Arkansas Regulations for the Control of Volatile Organic 
Compounds were adopted by the Arkansas Commission on Pollution Control 
and Ecology on April 10, 1981 and submitted by the Governor on April 23, 
1981.
    (14) A variance to Regulation 8 for Weyerhaeuser Gypsum Plant in 
Nashville, Arkansas was submitted by the Governor on June 29, 1981.
    (15) On April 23, 1981, the Governor submitted revisions to the plan 
to incorporate Federal Prevention of Significant Deterioration (PSD) 
Regulations 40 CFR 52.21 by reference.
    (16) On September 11, 1981, the Governor submitted a revision to 
section 8 of the Regulations of the Arkansas Plan of Implementation for 
Air Pollution Control which implements an emission limit for Energy 
Systems Company of El Dorado, Arkansas.
    (17) The Arkansas State Implementation Plan for lead was submitted 
to EPA on December 10, 1979, by the Governor of Arkansas as adopted by 
the Arkansas Department of Pollution Control and Ecology on November 16, 
1979. A letter of clarification dated January 5, 1982, also was 
submitted.
    (18) Revisions to the plan for intergovernmental consultation, 
interstate pollution abatement, and composition of the Arkansas 
Commission on Pollution Control and Ecology were submitted to EPA by the 
Arkansas Department of Pollution Control and Ecology on January 9, 1980.
    (19) Revision to the plan for maintenance of employee pay was 
submitted to EPA by the Arkansas Department of Pollution Control and 
Ecology on January 9, 1980.
    (20) On April 24, 1980, the Governor submitted final revisions to 
the ambient monitoring portion of the plan.
    (21) On December 10, 1979, the Governor submitted a revision to 
Section 5.1(a) of the Regulation of the Arkansas Plan of Implementation 
for Air Pollution Control, which controls VOC emissions. This revision 
was adopted by the Arkansas Commission on Pollution Control and Ecology 
on November 16, 1979.
    (22) On July 12, 1985, the Governor submitted a revision entitled, 
``Protection of Visibility in Mandatory Class I Federal Areas, May 6, 
1985.'' This submittal included new source review regulations and 
visibility monitoring strategy as adopted by the Arkansas Commission on 
Pollution Control and Ecology on May 24, 1985.
    (i) Incorporation by reference.
    (A) New source review regulations include amendments to rules and 
regulations of the Arkansas Department of Pollution Control and Ecology 
entitled, ``Prevention of Significant Deterioration Supplement to the 
Arkansas

[[Page 102]]

Plan of Implementation for Air Pollution Control,'' Sections 1 through 
6, adopted on May 24, 1985.
    (B) Arkansas Department of Pollution Control and Ecology Minute 
Order No. 85-12, adopted May 24, 1985.
    (ii) Additional Material.
    (A) Narrative submittal, including introduction, and visibility 
monitoring strategy.
    (23) A revision to the Arkansas Plan of Implementation of Air 
Pollution Control was submitted by the Governor on November 25, 1985.
    (i) Incorporation by reference. (A) Act 763 of 1985 (public 
availability of emission data) approved April 3, 1985. Act 763 of 1985 
amends section 82-1937 (Industrial secrets confidential--Revealing a 
misdemeanor) of the Arkansas Water and Air Pollution Control Act.
    (24) A revision to the Arkansas Plan of Implementation for Air 
Pollution Control was submitted by the Governor on December 16, 1985.
    (i) Incorporation by reference. (A) Act 817 of 1983 (permit fees) 
adopted March 25, 1983. Act 817 of 1983 added sections 82-1916 thru 82-
1921 to the Arkansas Statutes. (B) Arkansas Department of Pollution 
Control and Ecology Regulation No. 9 (Regulations for Development and 
Implementation of a Permit Fee System for Environmental Permits) adopted 
by the Arkansas Commission on Pollution Control and Ecology on November 
16, 1984. Only those portions of Regulation No. 9 related to air permits 
are incorporated.
    (25) Part II of the Visibility Protection Plan was submitted by the 
Governor on October 9, 1987.
    (i) Incorporation by reference.
    (A) Revision entitled ``Arkansas Plan of Implementation for Air 
Pollution Control--Revision: Protection of Visibility in Mandatory Class 
I Federal Areas: Part II--Long-Term Strategy, September 29, 1987''. This 
submittal includes a visibility long-term strategy and general plan 
provisions as adopted by the Arkansas Commission on Pollution Control 
and Ecology on September 25, 1987.
    (B) Arkansas Department of Pollution Control and Ecology, Minute 
Order No. 87-24, adopted September 25, 1987.
    (ii) Additional material.
    (A) None.
    (26) A revision to the Arkansas Plan of Implementation for Air 
Pollution Control, as adopted by the Arkansas Commission on Pollution 
Control and Ecology on May 22, 1987, was submitted by the Governor of 
Arkansas on July 1, 1987. This revision adds the definitions and 
dispersion technique regulations required to implement the Federal stack 
height regulations.
    (i) Incorporation by reference. (A) Sections 3(r), 3(s), 3(t), 3(u), 
3(v), 3(w), 3(x), 3(y), 5(f), and 5(g) of the Arkansas Plan of 
Implementation for Air Pollution Control as adopted by the Arkansas 
Commission on Pollution Control and Ecology on May 22, 1987.
    (ii) Additional material--None.
    (27) Revisions to the Arkansas State Implementation Plan for (1) the 
National Ambient Air Quality Standards and particulate matter 
definitions (subsections (z) through (ff) of ``Section 3. 
Definitions''). (2) Prevention of Significant Deterioration of Air 
Quality and its Supplement, and (3) subsection f(ix) of ``Section 4. 
Permits'', as adopted on March 25, 1988, by the Arkansas Commission on 
Pollution Control and Ecology, were submitted by the Governor on June 3, 
1988.
    (i) Incorporation by reference. (A) Regulations of the Arkansas Plan 
of Implementation for Air Pollution Control ``Section 3. Definitions'', 
subsections (z) through (ff), as promulgated on March 25, 1988.
    (B) Prevention of Significant Deterioration Supplement Arkansas Plan 
of Implementation For Air Pollution Control, as amended on March 25, 
1988.
    (C) Regulations of the Arkansas Plan for Implementation for Air 
Pollution Control ``Section 4. Permits'', subsection f(ix), as 
promulgated on March 25, 1988.
    (ii) Other material--None.
    (28) Revisions to the Arkansas State Implementation Plan for 
Prevention of Significant Deterioration (PSD) of Air Quality Supplement 
Arkansas Plan of Implementation for Air Pollution Control (PSD nitrogen 
dioxide increments), as adopted on May 25, 1990, by the Arkansas 
Commission on Pollution Control and Ecology, were submitted by the 
Governor on June 19, 1990.

[[Page 103]]

    (i) Incorporation by reference.
    (A) Prevention of Significant Deterioration Supplement Arkansas Plan 
of Implementation For Air Pollution Control as amended on May 25, 1990.
    (ii) Additional Material--None.
    (29)-(30)  [Reserved]
    (31) The State is required to implement a Small Business Stationary 
Source Technical and Environmental Compliance Assistance Program 
(PROGRAM) as specified in the plan revision submitted by the Governor on 
November 6, 1992. This plan submittal, as adopted by the Arkansas 
Commission on Pollution Control and Ecology on November 5, 1992, was 
developed in accordance with section 507 of the Clean Air Act. On April 
23, 1993, the Governor submitted Act 251 of 1993 which establishes the 
Compliance Advisory Panel (CAP) for the PROGRAM.
    (i) Incorporation by reference.
    (A) Act 251 of 1993 approved by the Governor on February 26, 1993. 
Included in this Act are provisions creating a CAP, establishing 
membership of the CAP, and addressing the responsibilities and duties of 
the CAP.
    (B) Arkansas Department of Pollution Control and Ecology, Minute 
Order No. 92-81, adopted November 5, 1992.
    (ii) Additional material.
    (A) Revision entitled, ``Arkansas Small Business Stationary Source 
Technical and Environmental Compliance Assistance Program SIP 
Revision'', adopted November 5, 1992.
    (B) Legal opinion letter dated November 5, 1992, from Steve Weaver, 
Chief Counsel, Arkansas Department of Pollution Control and Ecology, 
regarding legality of Commission teleconference meeting.
[37 FR 10850, May 31, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.170, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.171  Classification of regions.

    The Arkansas plan was evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                                  Pollutant
                                                           -----------------------------------------------------
                Air quality control region                  Particulate   Sulfur   Nitrogen   Carbon
                                                               matter     oxides    dioxide  monoxide    Ozone
----------------------------------------------------------------------------------------------------------------
Central Arkansas Intrastate...............................          II        III       III       III        III
Metropolitan Fort Smith Interstate........................          II        III       III       III        III
Metropolitan Memphis Interstate...........................           I        III       III       III          I
Monroe (Louisiana)-El Dorado (Arkansas) Interstate........          II        III       III       III        III
Northeast Arkansas Intrastate.............................         III        III       III       III        III
Northwest Arkansas Intrastate.............................         III        III       III       III        III
Shreveport-Texarkana-Tyler Interstate.....................          II        III       III       III        III
----------------------------------------------------------------------------------------------------------------

[37 FR 10850, May 31, 1972, as amended at 39 FR 16346, May 8, 1974; 45 
FR 6571, Jan. 29, 1980]



Sec. 52.172  Approval status.

    With the exceptions set forth in this subpart, the Administrator 
approves Arkansas' plan for the attainment and maintenance of the 
national standards under section 110 of the Clean Air Act. Further, the 
Administrator finds that the plan satisfies all requirements of Part D 
of the Clean Air Act, as amended in 1977, except as noted below.
[45 FR 6571, Jan. 29, 1980]



Secs. 52.173--52.180  [Reserved]



Sec. 52.181  Significant deterioration of air quality.

    (a) The plan submitted by the Governor of Arkansas on April 23, 1981 
(as adopted by the Arkansas Commission on Pollution Control and Ecology 
(ACPCE) on April 10, 1981), June 3, 1988 (as revised and adopted by the 
ACPCE on March 25, 1988), and June 19, 1990 (as revised and adopted by 
the ACPCE on May 25, 1990), Prevention of Significant Deterioration 
(PSD) Supplement Arkansas Plan of Implementation For Air

[[Page 104]]

Pollution Control, is approved as meeting the requirements of Part C, 
Clean Air Act for preventing significant deterioration of air quality.
    (b) The requirements of sections 160 through 165 of the Clean Air 
Act are not met for Federally designed Indian lands. Therefore, the 
provisions of Sec. 52.21 (b) through (w) are hereby incorporated by 
reference and made a part of the applicable implementation plan and are 
applicable to sources located on land under the control of Indian 
governing bodies.
[56 FR 20139, May 2, 1991, as amended at 63 FR 17683, Apr. 10, 1998; 63 
FR 32981, June 17, 1998]



Sec. 52.183  Small business assistance program.

    The Governor of Arkansas submitted on November 6, 1992, a plan 
revision to develop and implement a Small Business Stationary Source 
Technical and Environmental Compliance Assistance Program (PROGRAM) to 
meet the requirements of section 507 of the Clean Air Act by November 
15, 1994. The plan commits to provide technical and compliance 
assistance to small businesses, hire an Ombudsman to serve as an 
independent advocate for small businesses, and establish a Compliance 
Advisory Panel to advise the program and report to the EPA on the 
program's effectiveness. On April 23, 1993, the Governor submitted Act 
251 of 1993 which establishes the Compliance Advisory Panel for the 
PROGRAM.
[60 FR 12695, Mar. 8, 1995]



                          Subpart F--California



Sec. 52.219  Identification of plan--conditional approval.

    The plan revision commitments listed in paragraph (a) of this 
section were submitted on the date specified.
    (a) On November 13, 1992, California submitted a commitment to 
prepare a revision to the California State Implementation Plan (SIP) for 
the California ozone nonattainment areas to address the requirement in 
section 182(c)(4)(B) of the 1990 Clean Air Act Amendments that requires 
the States to develop a SIP revision for all ozone nonattainment areas 
classified as serious and above to opt-out of the Clean-Fuel Fleet 
Program by submitting for EPA approval a substitute program(s) resulting 
in as much or greater long-term reductions in ozone-producing and toxic 
air emissions. The State submittal contained an interim milestone to 
supply more accurate emission reduction data demonstrating equivalence 
no later than one year after the publication date of the Federal 
Register notice approving the State's committal SIP revision. California 
is required to submit the final SIP revision by May 15, 1994. The State 
held a public meeting on this committal SIP on March 17, 1992. The 
California SIP revisions are met automatically when the SIP revision 
concerns a regulation previously adopted by the Board.
    (b) [Reserved]
[58 FR 62533, Nov. 29, 1993]



Sec. 52.220  Identification of plan.

    (a) Title of plan: ``The State of California Implementation Plan for 
Achieving and Maintaining the National Ambient Air Quality Standards''.
    (b) The plan was officially submitted on February 21, 1972.
    (1) Mendocino County APCD.
    (i) Previously approved on May 31, 1972 and now deleted without 
replacement parts XI, XII, and part XIII.
    (2) Placer County APCD.
    (i) Previously approved on May 31, 1972 and now deleted without 
replacement Rule 42 (Mountain Counties Air Basin), Rules 40 and 42 (Lake 
Tahoe Air Basin).
    (3) Tehama County APCD.
    (i) Previously approved on May 31, 1972 and now deleted without 
replacement Rule 5.1.
    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) Air quality data submitted on April 10, 1972, by the Air 
Resources Board.
    (2) Report on status of regulations submitted on April 19, 1972, by 
the Air Resources Board.
    (3) Emission inventory submitted on April 21, 1972, by the Air 
Resources Board.
    (4) Air quality data submitted on April 26, 1972, by the Air 
Resources Board.

[[Page 105]]

    (5) Air quality data submitted on May 5, 1972, by the Air Resources 
Board.
    (6) Revised regulations for all APCD's submitted on June 30, 1972, 
by the Governor, except for:
    (i) San Diego County Air Pollution Control District.
    (A) Rule 65 is now removed without replacement as of March 14, 1989.
    (B) Previously approved on Septemeber 22, 1972 and now deleted 
without replacement Rules 44, 75, 77 to 80, 82 to 84, and 86 to 91.
    (C) Previously approved on September 22, 1972 and now deleted 
without replacement, Rules 12 and 13.
    (ii) Calaveras County APCD.
    (A) Previously approved on September 22, 1972 and now deleted 
without replacement Rule 305.
    (iii) Colusa County APCD.
    (A) Previously approved on September 22, 1972 and now deleted 
without replacement Rules 3.1 and 5.1 to 5.17.
    (iv) Fresno County APCD.
    (A) Previously approved on September 22, 1972 and now deleted 
without replacement Rules 501, 502, 504, 506, 508 to 512, 514, 516, and 
517..
    (v) Glenn County APCD.
    (A) Previously approved on September 22, 1972 and now deleted 
without replacement Rules 111, 113 to 117, 119 to 125, and 150.
    (vi) Kern County APCD (including Southeast Desert).
    (A) Previously approved on September 22, 1972 and now deleted 
without replacement Rules 502, 505 to 510, 512 to 515, and 517.
    (vii) Kings County APCD.
    (A) Previously approved on September 22, 1972 and now deleted 
without replacement Rules 502 to 509, 511 to 517.
    (viii) Lassen County APCD.
    (A) Previously approved on September 22, 1972 and now deleted 
without replacement Rules 1.5, 3.1, and 5.1 to 5.17.
    (ix) Madera County APCD.
    (A) Previously approved on September 22, 1972 and now deleted 
without replacement Rules 507 to 510 and 512 to 517.
    (x) Merced County APCD.
    (A) Previously approved on September 22, 1972 and now deleted 
without replacement Rules 502, 503, 506 to 510, and 512 to 517.
    (xi) Modoc County APCD.
    (A) Previously approved on September 22, 1972 and now deleted 
without replacement Rules 1.5 and 4.1 to 4.17.
    (xii) San Joaquin County APCD.
    (A) Previously approved on September 22, 1972 and now deleted 
without replacement Rules 502 and 506 to 509.
    (xiii) Stanislaus County APCD.
    (A) Previously approved on September 22, 1972 and now deleted 
without replacement Rules 303, 304, 502, 505 to 510 and 512 to 517.
    (xiv) Tulare County APCD.
    (A) Previously approved on September 22, 1972 and now deleted 
without replacement Rules 303, 304, 501, 502, 506 to 514, 516 to 518.
    (7) Information (Non-regulatory) regarding air quality surveillance 
submitted on July 19, 1972, by the Air Resources Board.
    (8) Compliance schedules submitted on December 27, 1973, by the Air 
Resources Board.
    (9) Compliance schedules submitted on February 19, 1974, by the Air 
Resources Board.
    (10) Compliance schedules submitted on April 22, 1974, by the Air 
Resources Board.
    (11) Compliance schedules submitted on June 7, 1974, by the Air 
Resources Board.
    (12) Compliance schedules submitted on June 19, 1974, by the Air 
Resources Board.
    (13) Compliance schedules submitted on September 4, 1974, by the Air 
Resources Board.
    (14) Compliance schedules submitted on September 19, 1974, by the 
Air Resources Board.
    (15) Compliance schedules submitted on October 18, 1974, by the Air 
Resources Board.
    (16) Compliance schedules submitted on December 4, 1974, by the Air 
Resources Board.
    (17) Compliance schedules submitted on January 13, 1975, by the Air 
Resources Board.
    (18) Air quality maintenance area designations submitted on July 12, 
1974, by the Governor.
    (19)-(20) [Reserved]
    (21) Revised regulations for the following APCD's submitted on July 
25, 1973, by the Governor.

[[Page 106]]

    (i) Lassen County APCD.
    (A) Appendix A (Implementation Plan for Agricultural Burning) and 
Appendix B (Enforcement).
    (ii) Modoc County APCD.
    (A) Rule 3:10A and Regulation V (Rules 5:1 to 5:7).
    (iii) Siskiyou County APCD.
    (A) Rules 2.13, 4.5, 4.12, 4.13, 4.14, and Implementation Plan for 
Agricultural Burning.
    (iv) Bay Area APCD.
    (A) Regulation 1.
    (1) Division 1, Sections 1000-1010.
    (2) Division 2, Section 2000.
    (3) Division 3, Sections 3000-3004, 3100-3111, 3115-3118, 3120, and 
3200-3500.
    (4) Division 4.
    (B) Regulation 4.
    (1) Sections 1-2.
    (C) Regulation 2.
    (1) Division 1, Sections 1214 to 1214.3.
    (D) Regulation 3.
    (1) Division 1, Sections 1205 to 1205.3.
    (v) Butte County APCD.
    (A) Sections 1-1 to 1-35, 2-8, 2-10 to 2-11, 2A-1 to 2A-18, 3-2 to 
3-2.1, 3-6, 3-9, 3-10.1, 3-11.1, 3.14, and 3.16.
    (vi) San Diego County APCD.
    (A) Rules 41, 55, 58, and 101-113.
    (B) [Reserved]
    (C) Previously approved on May 11, 1977 and now deleted without 
replacement, Rule 55.
    (vii) Tehama County APCD.
    (A) Rules 1:2, 3:1-3, 3:3a, 3:3b, 3:4-3:5, 3:5a, 3:6-3:14, 4:6, and 
Implementation Plan for Agricultural Burning.
    (B) Previously approved on May 11, 1977 and now deleted without 
replacement Rule 41.
    (viii) Yuba County APCD.
    (A) Rules 1.1, 2.1-2.2, 2.10, 4.11, and Agricultural Burning 
Regulations, Sections 1 to 6.
    (B) Rule 4.5.
    (ix) Kings County APCD.
    (A) Rules 102, 105-108, 110, 404-406, 409, 417-I, II, IV, and 510.
    (B) Rule 111.
    (C) Previously approved on August 22, 1977 and now deleted without 
replacement Rule 510.
    (x) Colusa County APCD.
    (A) Rule 6.5 and Amendment Number 3.
    (B) Rule 4.4g.
    (xi) Imperial County APCD.
    (A) Agricultural Burning Implementation Plan (Rules 200-206).
    (xii) Sacramento County APCD
    (A) Rules 72, 90, 91, and 92.
    (xiii) Ventura County APCD.
    (A) Rules 2, 37, 56, 59, 60, and 101.
    (xiv) Yolo-Solano APCD.
    (A) New or amended Rules 1.2 (a, b, d to g, i to x, and z to ae), 
1.4, 2.4(e), 2.8, 2.9, 4.1 to 4.5, 5.1 to 5.18, 6.1 (i) and (j), 6.2 to 
6.5, and 6.7 to 6.8.
    (B) Previously approved on June 14, 1978 and now deleted without 
replacement Rules 4.4, 4.5, 5.2, 5.3, 5.5, 5.7 to 5.9, and 5.13 to 5.17.
    (xv) San Bernardino County APCD.
    (A) New or amended Rules 5(a), 53A, 57, 57.1, 57.2.
    (xvi) Santa Barbara County APCD.
    (A) Rules 2(a, b, k, l, m, n, o, p, q, r, s, t, u, v, w), 40 [with 
the exception of 40(4)(m)].
    (xvii) Calaveras County APCD.
    (A) Rules 110 and 402(f).
    (xviii) Los Angeles County APCD (Metropolitan Los Angeles portion).
    (A) Amended Rule 45.
    (22) Revised regulations for the following APCD's submitted on 
November 2, 1973 by the Governor's designee.
    (i) Bay Area APCD.
    (A) Regulation 2.
    (1) Division 1, Section 1222.
    (2) Division 3, Section 3211.
    (3) Division 4, Section 4113.
    (4) Division 8, Sections 8414-8416.
    (5) Division 9, Sections 9613, 9615, 9711.3, and 9711.5.
    (6) Division 11, Section 11101.
    (23) Revised regulations for the following APCD's submitted on 
January 22, 1974 by the Governor's designee.
    (i) Sacramento County APCD.
    (A) Rule 30.
    (ii) Santa Barbara County APCD.
    (A) Rules 22, 24.1, 24.2.
    (24) Revised regulations for the following APVD's submitted on July 
19, 1974, by the Governor's designee.
    (i) Sutter County APCD.
    (A) Rule 1.3
    (ii) Bay Area APCD.
    (A) Regulation 1: (1) Sections 3112-3114, 3119 and 3122.
    (iii) San Diego County APCD.
    (A) Regulation IX.
    (B) Rule 61.
    (iv) Stanislaus County APCD.
    (A) Rules 103, 108, 108.1, 113, 401, 402, 403, 404, 405, 409.1, 
409.2, 418, 421, 505, 518, and 401.1.

[[Page 107]]

    (B) Rule 110.
    (v) Tehama County APCD.
    (A) Rules 3:14 and 4:18.
    (B) Rule 4:17.
    (vi) Shasta County APCD.
    (A) Rules 1:1 to 1:2, 2:6(1.)(a), 2:6(1.)(b) (i-ii and iv-vii) 
2:6(1.)(c)(i-vi), 2:6(1.)(d-e), 2:6(2-4), 2:7, 2:8(a-c), 2:9, 2:11, 
2:14, 2:25, 3:1 to 3:9, 3:11 to 3:12, and 4:1 to 4:23.
    (B) Rule 3:10.
    (C) Previously approved on August 22, 1977 and now deleted without 
replacement Rules 4.2 to 4.4, 4.8 to 4.10, 4.15, and 4.23.
    (vii) Kern County APCD.
    (A) Rules 102, 103, 108, 108.1, 110, 113, 114, 301, 305, 401, 404, 
405, 407.3, 409, 411, 413, 414, 417-I and II, 504, 516, and 518
    (B) Rule 111.
    (C) Rules 601-615, except those portions pertaining to sulfur 
dioxide and the 12-hour carbon monoxide criteria levels.
    (D) Previously approved on August 22, 1977 and now deleted without 
replacement Rule 516 (including Southeast Desert).
    (viii) Sacramento County APCD.
    (A) Rules 11, 39, 44, 70, 73, and 111.
    (B) Rules 123 and 124, except those portions that pertain to the 12-
hour CO criteria level.
    (ix) Yolo-Solano APCD.
    (A) Rule 2.22.
    (B) New or amended Rules 1.2(c, h, and y), 1.3, 2.11 to 2.16, 2.19, 
4.3, 5.4, 5.6, and 5.12.
    (C) Previously approved on June 14, 1978 and now deleted without 
replacement Rules 5.6 and 5.12.
    (x) Ventura County APCD.
    (A) Rules 2, 3, 31, 32, 200, 203, and 204.
    (B) Rule 32.
    (C) Rules 70, 73.
    (D) Rule 96.
    (E) Rule 111.
    (xi) Santa Barbara County Air Pollution Control District.
    (A) Rules 150 to 152, 154 to 159, 160A, and 161 to 164, except those 
portions pertaining to nitrogen oxides, sulfur dioxide and the 12-hour 
carbon monoxide criteria levels.
    (25) Revised regulations for the following APCD's submitted on 
October 23, 1974 by the Governor's designee.
    (i) Fresno County APCD.
    (A) Rules 102, 103, 108, 108.1, 111-114, 401, 404-406, 408, 409.1, 
409.2, 416, 416.1a, b, c(2), c(3), d, e(2), and f, 505 and 518.
    (B) Rule 110.
    (C) New or amended Rules 402 (a to g), 416.1(c)(1), 416.1(e)(1), 
416.1(e)(3), and 416.1(e)(4).
    (D) Rules 601-615, except those portions pertaining to sulfur 
dioxide and the 12-hour carbon monoxide criteria levels.
    (E) Previously approved on August 22, 1977 and now deleted without 
replacement Rule 505.
    (ii) San Joaquin County APCD.
    (A) Rules 102, 103, 108, 108.1, 108.2, 113, 305, 404-406, 407.2, 
407.3, 408, 408.1, 409.1, 409.2, 410, 413, 414, 416, 416.1A to C, and 
D.3 to E., 417, 420, 420.1, 421, 504, 505, and 510-520.
    (B) Rule 110.
    (C) New or amended Rules 416.1 (D)(1) and (D)(2).
    (D) Previously approved on August 22, 1977 and now deleted without 
replacement Rules 504, 505, 510, 512 to 518, and 520.
    (iii) Lake County APCD.
    (A) Parts II--V, Sections 3-7 of Part VI, Parts XI-XIII, Appendix A 
(Agricultural Burning Definitions A-M, Burning Regulations/Agricultural 
Burning (Farm) 1-9, /Farm 1-3, /Range 1-2), Appendix B (Parts I-II, Part 
IV-1, 2, 5, and 6, Part V-1, 4, 5 and 6, Parts VI-VII, Part VIII-1-7 and 
9, Parts IX-X), Tables I-IV.
    (iv) Tulare County APCD.
    (A) Rules 102, 103, 108.1, 110, 112-114, 302, 401, 404-406, 407.3, 
408, 410, 410.1, 410.2, 411, 420, 503-505, and 515.
    (B) Previously approved on August 22, 1977 and now deleted without 
replacement Rules 503 to 505, 515, and 519.
    (v) Ventura County APCD.
    (A) Rules 2 and 125.
    (vi) Santa Barbara County Air Pollution Control District.
    (A) Rule 160B, except those portions pertaining to nitrogen oxides, 
sulfur dioxide and the 12-hour carbon monoxide criteria levels.
    (vii) Monterey Bay Unified APCD.
    (A) Rules 100 to 106, 300 to 303, 400 to 401, 403, 404(a)(b)(d), 405 
to 408, 412 to 417, 419 to 420, 500 to 508, 600 to 616, and 800 to 816.

[[Page 108]]

    (26) Revised regulations for the following APCD's submitted on 
January 10, 1975, by the Governor's designee.
    (i) Sutter County APCD
    (A) Rule 4.1
    (ii) Bay Area APCD
    (A) Regulation 2: (1) Sections 2018.1-2.
    (B) Regulation 7.
    (C) Regulation 8.
    (iii) Butte County APCD.
    (A) Sections 3-11, 3-12, and 3-12.1.
    (iv) Glenn County APCD.
    (A) Sections 2, 3.1, 10-14.3, 16, 17, 21, 21.1, 24, 57, 58, 81, 85, 
86, 95.1, 118, 122.1-122.3, 154 and 155.
    (B) Rules 95.2 and 95.3.
    (C) Previously approved on May 11, 1977 and now deleted without 
replacement Rules 118 and 122.1 to 122.3.
    (v) Yuba County APCD.
    (A) Agricultural Burning Regulations, sections 1 and 3.
    (vi) Colusa County APCD.
    (A) Rules 6.2 and 6.4.d. (1-2).
    (vii) Fresno County APCD.
    (A) Rules 409, 417, 503, 507, 513, and 515.
    (B) Previously approved on August 22, 1977 and now deleted without 
replacement Rules 503, 507, 513, and 515.
    (viii) Mariposa County APCD.
    (A) Rules 101, 102, 201, 202, 203 (a-f, h, i, and k), 204-216, 301-
303, 305-306, 308-313, 315-323, 401-403, 405-409, and 600-618.
    (B) Rule 203(j).
    (C) Previously approved on August 22, 1977 and now deleted without 
replacement Rules 601, 602, 604 to 609, 611 to 616, and 618.
    (ix) Sierra County APCD.
    (A) Rules 101, 102, 201-216, 301-323, 405-409, 601-620, 6, 27, 29, 
and 51-56.
    (B) Previously approved and now deleted, Rule 102.
    (x) Shasta County APCD.
    (A) Rules 2:6(5)(b), 3:1, 3:2, 4:6, and 4:14.
    (xi) Tulare County APCD.
    (A) Rules 417 and 417.1a. thru d., e.2., and f.
    (B) New or amended Rules 417.1 (e)(1), (e)(3) and (e)(4).
    (xii) Kern County APCD.
    (A) Rules 410 and 503.
    (xiii) Madera County APCD.
    (A) Rules 102, 103, 105, 108, 112-114, 301, 305, 401, 402, (a-e, and 
g), 404-406, 407.2, 407.3, 408, 409, 409.1 409.2, 412, 416, 416.1a, b, 
c(2), c(3), d, e(2), f, 504, 505, and 518.
    (B) Rule 402(f).
    (C) Rule 110.
    (D) New or amended Rules 416.1 (c)(1), (e)(1), (e)(3), and (e)(4).
    (xiv) Yolo-Solano APCD.
    (A) New or amended Rule 6.1 (a), (b), (c), (d), (e), and (g) (1, 2, 
and 3).
    (xv) Monterey Bay Unified APCD.
    (A) Rules 49 to 411 and 421.
    (xvi) Plumas County APCD.
    (A) Rule 203(j).
    (B) New or amended Rules 101, 102, 201, 202, 204, 206, 209, 210(a), 
214, 216, 216-49, 216-50, 216-51, 216-54, 216-55, 216-56, 216-1, 216-2, 
216-3, 305, 306, 309, 310, 311, 312, 313, 314, 315, 316, 317, 318, 401, 
403, 405, 406, 408, 701, 702, 704, 705, 706, 707, 708, 709, 711, 712, 
713, 714, 715, 716, 717.
    (C) Previously approved and now deleted (without replacement) Rules 
51.7, 57.5, 62, 70.
    (D) Previously approved on June 14, 1978 and now deleted without 
replacement Rules 705 to 709.
    (E) Previously approved and now deleted, Rule 102.
    (xvii) Placer County APCD.
    (A) New or amended Rules 102, 105, 201, 202, 204, 209, 312, 403, 
405, 406, 701, 705, 707, 711, 712, 713, 714, 716, 717.
    (B) Previously approved on June 14, 1978 and now deleted without 
replacement Rules 701, 707, 711 to 714, and 716 (Mountain Counties Air 
Basin).
    (C) Previously approved on June 14, 1978 and now deleted without 
replacement Rules 701, 705, 707, 711 to 714, and 716 (Lake Tahoe Air 
Basin).
    (27) Revised regulations for the following APCD's submitted on April 
10, 1975, by the Governor's designee.
    (i) Stanislaus County APCD.
    (A) Rule 409.
    (ii) Tehama County APCD.
    (A) Rule 4:6.
    (iii) Sacramento County APCD.
    (A) Rules 12, 22a, 22b, 25, 32-34, and 40.
    (iv) Bay Area APCD.
    (A) Regulation 2, section 1302.2 and section 1302.22.
    (B) Rules 32, 33, 34, 38, 40.
    (v) San Bernardino County APCD.
    (A) New or amended Rule 73.
    (vi) Riverside County APCD.
    (A) New or amended Rule 57.
    (vii) Nevada County APCD.
    (A) New or amended Rules 101, 102, 105, 106, 107, 201, 202, 203 
[with exception of (g)], 204, 206, 208, 209, 210(a), 212, 214,

[[Page 109]]

215, 301, 302, 303, 305, 306, 307, 308, 309, 310, 311, 312, 313, 314, 
315, 316, 317, 318, 322, 401, 403, 405, 406, 408, 601, 602, 701, 702, 
703, 705, 706, 707, 708, 709, 711, 712, 713, 714, 715, 716, 717.
    (B) Previously approved on June 14, 1978 and now deleted without 
replacement Rules 701 to 703, 705 to 709, and 712 to 716.
    (C) Previously approved and now deleted, Rule 102.
    (viii) El Dorado County APCD.
    (A) New or amended Rules 101, 102, 202, 204, 206, 209, 210(a), 212, 
214, 301, 305, 306, 309, 310, 311, 312, 313, 315, 316, 317, 318, 323, 
401, 403, 405, 406, 408, 601, 602, 701, 702, 704, 705, 706, 707, 708, 
709, 711, 712, 713, 714, 715, 716, 717.
    (B) Previously approved and now deleted (without replacement) Rules 
5, 6, 7.
    (ix) [Reserved]
    (x) Santa Barbara County APCD.
    (A) Rules 32, 36, 36.3, 36.4, 36.5, 37, 38.
    (28) Revised regulations for the following APCD's submitted on July 
22, 1975, by the Governor's designee.
    (i) Sutter County APCD
    (A) Rules 1.2, 2.82, and 4.11.
    (ii) San Diego County APCD.
    (A) Rule 66.
    (iii) Yuba County APCD
    (A) Rule 1.1.
    (iv) Calaveras County APCD.
    (A) Rules 102, 201-215, 301-323, 401-403, 405-408, 409 (Public 
Records), 601-604, 700-717, 105, 106, 110, 407(b), 409 (Organic 
Solvents), 409.1 (Architectural Coatings), 409.2 (Disposal and 
Evaporation of Solvents), 412, and 413.
    (B) Previously approved on August 22, 1977 and now deleted without 
replacement Rules 701, 704 to 709, 711 to 714, and 716.
    (v) Tuolumne County APCD.
    (A) Rules 102, 201, 202, 203, (a-f, h, i, and k), 204-216, 301-303, 
305-306, 308-313, 315-323, 400-403, 405-408, 409 (Public Records), 600-
618, 105-110, 301-304, 409 (Fuel Burning Equipment, Oxides of Nitrogen), 
410, and 412-414.
    (vi) Kings County APCD.
    (A) Rule 410.
    (vii) Shasta County APCD.
    (A) Rule 2.8(e).
    (viii) Kern County APCD.
    (A) Rules 115, 407.1, 422, and 423.
    (ix) Sacramento County APCD.
    (A) Rule 93.
    (x) Riverside County APCD.
    (A) New or amended Rule 53.
    (xi) Orange County APCD (Metropolitan Los Angeles portion).
    (A) Amended Rule 53.
    (29) Revised regulations for the following APCD's submitted on 
November 3, 1975 by the Governor's designee.
    (i) Lake County APCD.
    (A) Part III, Number 59a.
    (ii) Sacramento County APCD.
    (A) Rules 13 and 14.
    (B) Rules 71, 112, and 113.
    (iii) Monterey Bay Unified APCD.
    (A) Rule 418.
    (iv) Bay Area APCD.
    (A) Regulation 2, section 1302.21 and section 1302.23.
    (v) San Diego County.
    (A) Rule 63.
    (B) Rules 112, 113.
    (vi) Ventura County APCD.
    (A) Rules 65, 66, 72, and 73.
    (30) Revised regulations for the following APCD's submitted on 
February 10, 1976 by the Governor's designee.
    (i) Bay Area APCD
    (A) Regulation 1: (1) Section 3121.
    (B) Regulation 6.
    (ii) Butte County APCD
    (A) Section 3-11.2
    (iii) Yuba County APCD.
    (A) Agricultural Burning Regulations, sections 1 and 3.
    (iv) Colusa County APCD.
    (A) Rule 6.6A.I and 6.6A.II-1. (a-f).
    (v) Fresno County APCD.
    (A) Rules 115, 422, 423, and 407.
    (vi) San Joaquin County APCD.
    (A) Rules 114, 401, 402, 407.1, 409, 411, 422 and 423.
    (B) [Reserved]
    (C) Rule 411.1 and 411.2.
    (vii) Lake County APCD.
    (A) Table V.
    (viii) Sacramento County APCD.
    (A) Rules 94-97.
    (ix) Ventura County APCD.
    (A) Rules 70 and 71.
    (x) Southern California APCD.
    (A) New or amended Rules 501, 502, 506, 507, 508, 509, 511, 512, 
513, 514, 515, 516, 517, 518, 801, 803, 804, 807, 808, 809, 810, 811, 
813, 814, 815, 817.
    (B) Previously approved on June 14, 1978 and now deleted without 
replacement Rules 501, 502, 506 to 509, 511 to 518, 801, 803 to 804, 807 
to 811, 813 to 815, and 817.

[[Page 110]]

    (xi) Santa Barbara County APCD.
    (A) Rule 32.1.
    (31) Revised regulations for the following APCD's submitted on April 
21, 1976, by the Governor's designee.
    (i) Great Basin Unified APCD.
    (A) [Reserved]
    (B) Rules 100 to 107, 215, 300 to 303, 400 to 402, 404 to 413, 416 
to 421, 500 to 501, 600 to 616, and 800 to 817.
    (C) Alpine County APCD: Rules 1.4, 3.1, 4.2-1, 4.7, 4.7-1, 4.8, 
4.10, 4.11, and 5.18.
    (D) Inyo County APCD: Rules 1.3, 3.1, 4.1, 4.10, 4.11, 4.12, and 
5.1.
    (E) Mono County APCD: Rules 1.4, 3.1, 4.2-1, 4.7, 4.7-1, 4.8, 4.10, 
4.11, 5.1, and 5.18.
    (F) Previously approved on June 6, 1977 and now deleted without 
replacement Rules 600 to 615 and 800 to 817.
    (ii) Sutter County APCD
    (A) Rule 4.1
    (iii) San Diego County APCD.
    (A) Rule 5.
    (iv) Glenn County APCD
    (A) Sections 14.3 and 15.
    (v) Kings County APCD.
    (A) Rule 411.
    (B) Rules 412 and 412.1.
    (vi) Southern California APCD.
    (A) Rules 461 and 462.
    (B) New or amended Rules 103, 104, 105, 106.
    (C) Rules 201-207, 209-212, 214-217, and 219.
    (vii) Santa Barbara County APCD.
    (A) Rule 35.1 and 35.2.
    (B) Rule 2(x).
    (C) Rule 63, except those portions pertaining to sulfur dioxide and 
the 12-hour carbon monoxide criteria levels.
    (viii) Fresno County APCD.
    (A) Rule 411 and 411.1.
    (ix) Kern County APCD.
    (A) Rule 412 and 412.1.
    (x) Stanislaus County APCD.
    (A) Rule 411 and 411.1.
    (xi) Tulare County APCD.
    (A) Rule 412 and 412.1.
    (xii) Madera County APCD.
    (A) Rule 411.1 and 411.2.
    (xiii) Ventura County APCD.
    (A) Rules 2, 4, 36, 40, 41, 42, 43, 104, 201, and 202.
    (B) Previously approved on August 15, 1977 and now deleted without 
replacement Rule 43.
    (xiv) Yolo-Solano APCD.
    (A) New or amended Rules 6.1(f) (1 and 2), (g)(4), (h) (1 and 2) and 
6.6.
    (xv) Nevada County APCD.
    (A) Amended Rule 211.
    (xvi) Bay Area APCD.
    (A) Regulation 2, section 3212.
    (B) Regulation 3, section 3203.
    (xvii) [Reserved]
    (xviii) Amador County APCD.
    (A) Rule 404.
    (B) New or amended Rules 101, 102, 104, 105, 106, 107, 201, 202, 
204, 206, 207.1, 209, 210(A), 211, 212, 213.2, 213.3, 214, 305, 307, 
308, 312, 401, 402, 403, 405, 406, 408, 409, 601, 602, 603, 702, 704, 
705, 706, 707, 708, 709, 711, 712, 713, 714, 715, 716, 717.
    (C) Previously approved and now deleted (without replacement) Rules 
18.1 (Regulation V), 22 (Regulation V).
    (D) Previously approved on January 24, 1978 and now deleted without 
replacement Rules 705 to 709 and 712 to 716.
    (32) Revised regulations for the following APCD's submitted on 
August 2, 1976 by the Governor's designee.
    (i) Bay Area APCD.
    (A) Regulation 2: (1) Sections 2022.1-2, 2035.1, 3211.1, and 
Divisions 16-18.
    (ii) Stanislaus County APCD.
    (A) Rules 102, 104, 105, 111, 112, 114, 301, 305, 407.1, 416, 416.1, 
422, 423, 501, 504, and 511.
    (B) Previously approved on August 22, 1977 and now deleted without 
replacement Rules 501, 404, and 511.
    (iii) Merced County APCD.
    (A) Rules 411 and 411.1.
    (B) Rule 109.
    (C) New or amended Rules 102, 103, 103.1, 104, 105, 108.1, 110 to 
115, 302, 401, 404, 405, 407.1, 408.1, 408.2, 409, 409.1, 409.2, 410, 
412, 416, 416.1[(I), (II) (A-L), (II) (N-O), (III), (IV), (V), and 
(VI)], 421(a), 501, 504, 505, 511, and 518.
    (D) Previously approved and now deleted (without replacement) Rules 
102(hh) and 102(ii).
    (E) Previously approved on June 14, 1978 and now deleted without 
replacement Rules 105, 501, amd 504.
    (iv) Southern California APCD.
    (A) New or amended Rules 403, 404, 405, 407, 408, 409, 432, 441, 
443, 464, 465, 467, 470, 471, 472, 473, 504, 505, 510, 802, 805, 806, 
812, 816.
    (B) Previously approved and deleted (without replacement).

[[Page 111]]

    (1) Los Angeles County APCD Rules 53.1, 55.
    (2) San Bernardino County APCD Rules 50, 51.
    (3) Riverside County APCD Rule 55.
    (4) Orange County APCD Rule 55.
    (C) Rules 202 and 219.
    (D) Previously approved on June 14, 1978 and now deleted without 
replacement Rules 504, 505, 510, 802, 805, 806, 812, and 816.
    (E) Previously approved on June 14, 1978 and now deleted without 
replacement.
    (1) Los Angeles County APCD Rule 505.
    (2) Riverside County APCD Rule 505.
    (3) San Bernadino County APCD Rule 505.
    (v) Plumas County APCD.
    (A) Amended Rule 324.
    (vi) El Dorado County APCD.
    (A) Amended Rule 211.
    (33)-(34) [Reserved]
    (35) Revised regulations for the following APCDs submitted on 
November 10, 1976 by the Governor's designee.
    (i) Sacramento County APCD.
    (A) Rules 1, 2, 11, 12, 21, 22a, 22b, 24, 25, 27, 28, 29, 33, 39, 
44, 70, 71, 90, 92, 93, 94, 95, 96, 97, 98, and definitions list 
addition to Regulation VII.
    (B) Rule 14.
    (ii) Southern California APCD.
    (A) Rule 461.
    (iii) Ventura County APCD.
    (A) Rule 70.
    (B) Rules 2, 57, 72, and 73 and Regulation VII (Rules 110-129).
    (C) Previously approved on August 15, 1977 and now deleted without 
replacement Rules 115 to 119, 112, and 128 to 129.
    (iv) Santa Barbara County APCD.
    (A) Rule 35.2.
    (v) San Joaquin County APCD.
    (A) Rules 102, 103, 103.1, 104, 105, 111, 112, 301, 305, 402, 416.1, 
501, 504, 511.
    (B) Previously approved on October 4, 1977 and now deleted without 
replacement Rule 501.
    (vi) Tulare County APCD.
    (A) Rules 102, 103, 103.1, 104, 105, 110, 112, 115, 305 (402 
paragraphs a. through e. and g.), 405, 407.1, 407.3, 409, 417.1, and 
421.
    (B) Rules 111 and 402(f).
    (C) Previously approved on September 21, 1976 and now deleted 
without replacement Rules 105 and 305.
    (vii) Fresno County APCD.
    (A) Rules 407 and 408.
    (viii) Imperial County APCD.
    (A) Rules 100, 114.5, 131.5, and 148.D(3).
    (ix) Del Norte County APCD.
    (A) Rule 540.
    (B) [Reserved]
    (C) New or amended Rules 100, 110, 120, 130, 150, 160 (except 160(a) 
and non-criteria pollutants), 190, 240(d) (except paragraph (3)), 300, 
310, 320, 340, 400(b), 410(a), 410(c), 420, 430, 440, 470, 480, 482, 
500, 510, 520, 600, 610, 620, 630, 640, and 650; and the following 
portions of Regulation 2: General prohibitions (all of page 1), Articles 
I and II, paragraphs A1, A2, A3, A4, 5, 7, and 8 of Article III, and 
Articles IV to VII.
    (x) San Diego County APCD.
    (A) Rules 2(k), 3, 50, 52, 53, 60, 62.
    (xi) Monterey Bay Unified APCD.
    (A) Rules 101, 104, 106, 214, 301, 404(c), 406, 407, 415, 601 to 
603, 609, 801, 805, and 811.
    (xii) San Luis Obispo County APCD.
    (A) New or amended Rules 101 Title, 102, 103, 105(A)(2) through 
105(A)(46), 106, 108, 109, 110 Enforcement, 111, 401, 403, 405, 408, 
409, 410, 801, 802, 803, 804, 805, 806, 807, 808, 809, 810, 811, 812, 
813, 814, 815, 816, 817.
    (B) Rule 107.
    (C) Rules previously approved and now deleted (without replacement) 
101(1)(b), 101(2), 101(3), and 101(4) Effective Date, 110 Prohibitions, 
116(1), 116(3), 119(1) and 119(4).
    (D) Amended Rules 501 and 502 (sections A-F, H-I, K-N, O(1), P-Q).
    (E) New or amended Rules 202, 205, 206, 207, 208, 209, 210, and 211.
    (F) Previously approved on August 4, 1978 and now deleted without 
replacement Rules 801 to 817.
    (xiii) Kern County APCD.
    (A) New or amended Rules 102, 102(d), 102(oo), 103, 103.1, 104 to 
105, 110, 112, 301(f), 305(a), 402 (c) and (e), 417(I)(A), 
417(II)(B)(L), 501, and 511.
    (B) Rule 504.
    (C) Previously approved on March 22, 1978 and now deleted without 
replacement Rules 105, 501, 504, and 511 (including Southeast Desert).
    (xiv) Humboldt County APCD.
    (A) Rule 540.
    (B) [Reserved]
    (C) New or amended Rules 100, 110, 120, 130, 150, 160 (except 160(a) 
and non-

[[Page 112]]

criteria pollutants), 190, 240(d) (except paragraph (3)), 300, 310, 320, 
340, 400(b), 410(a), 410(c), 420, 430, 440, 470, 480, 482, 500, 510, 
520, 600, 610, 620, 630, 640, and 650; and the following portions of 
Regulation 2: General prohibitions (all of page 1), Articles I and II, 
paragraphs A1, A2, A3, A4, 5, 7, and 8 of Article III, Articles IV to 
VII, and Appendix A.
    (D) Previously approved and now deleted (without replacement) Rules 
5, 6, 80, 87, and 95.
    (E) Previously approved on August 2, 1978 and now deleted without 
replacement Rules 340, 510, and 620 to 650.
    (xv) Mendocino County APCD.
    (A) Rule 540.
    (B) [Reserved]
    (C) New or amended Rules 100, 110, 120, 130, 150, 160 (except 160(a) 
and noncriteria pollutants), 190, 300 (except paragraph (a)), 310, 340, 
400(b), 410(b), 410(c), 430, 440, 460, 470, 480, 482, 500, 510, 520, 
600, 610, 620, 630, 640, and 650; and the following portions of 
regulation 2: General prohibitions (all of page 1), Articles I and II, 
paragraphs A1, A2, A3, A4, 5, 7, and 8 of Article III, Articles IV and 
V, Article VI(a) to (i), Article VII, and Appendices B and C.
    (D) Previously approved and now deleted (without replacement) Parts 
IV, V-5-B, VI-1, and VI-4.
    (E) Previously approved on November 7, 1978 and now deleted without 
replacement Rules 510, 620, 640, and 650.
    (xvi) Northern Sonoma County APCD.
    (A) Rule 540.
    (B) New or amended Rules 100, 110, 120, 130, 150, 160, (except 
160(a) and non-criteria pollutants), 190, 300, 310, 320, 340, 400(b), 
410(a), 410(c), 420, 430, 440, 470, 480, 482, 500, 510, 520, 600, 610, 
620, 630, 640, and 650; and the following portions of Regulation 2: 
General prohibitions (all of page 1), Articles I and II, paragraphs A1, 
A2, A3, A4, 5, 7, and 8 of Article III, Articles IV and V, paragraphs 
(a) to (i) of Article VI, and Article VII.
    (C) Previously approved on August 16, 1978 and now deleted without 
replacement Rules 340, 510, 600, 610, 620, 630, 640, and 650.
    (xvii) Trinity County APCD.
    (A) Rule 540.
    (B) [Reserved]
    (C) New or amended Rules 100, 110, 120, 130, 150, 160 (except 160(a) 
and non-criteria pollutants), 190, 240(d) except paragraph (3)), 300, 
310, 320, 340, 400(b), 410(a), 410(c), 420, 430, 440, 470, 480, 482, 
500, 510, 520, 600, 610, 620, 630, 640, and 650; and the following 
portions of regulation 2: General prohibitions (all of page 1), articles 
I and II, paragraphs A1, A2, A3, A4, 5, 7 and 8 of article III, articles 
IV and V, paragraphs (a) to (i) of article VI, and article VII.
    (D) Previously approved on August 2, 1978 and now deleted without 
replacement Rules 340, 510, and 620 to 650.
    (36) Revised regulations for the following APCD were submitted on 
November 19, 1976, by the Governor's designee.
    (i) Southern California APCD.
    (A) Rules 213, 213.1, and 213.2.
    (37) Revised regulations for the following APCD's submitted on 
February 10, 1977, by the Governor's designee.
    (i) Southern California APCD.
    (A) New or amended Rules 102, 468, 469, 474, 475, 476.
    (B) Rule 430.
    (C) Amended Rule 431.
    (ii) San Diego County APCD.
    (A) Rule 68.
    (iii) San Luis Obispo County APCD.
    (A) Rule 112, and Rules 404(A) through 404(B)(1)(a), 404(B)(1)(c), 
404(B)(2), 404(B)(3), 404(B)(4), 404(c), 404(D), and 404(E).
    (iv) Lake County APCD.
    (A) Rules 500, 510, and 511.
    (B) New or amended sections 100, 200 to 205.1, 207 to 234, 236, 238 
to 260, 300, 301, 400, 401, 402 (A to E, and G), 410, 411, 412 (A and 
C), 430 to 439, 520, 530 to 533, 800, 900 to 902, 1000 to 1003, 1100, 
1200, 1300, 1400, 1500, 1600, 1601, 1610, 1611, 1612, 1620, 1700, 1701, 
1710 to 1714, 1720 to 1725, 1730, 1731 to 1736, and tables I, II, III, 
IV, and V.
    (C) Previously approved and now deleted (without replacement) part 
II; sections 9, 15, 18, 28, 42, 43, 49a, 49b, 50, 52, and 54 of part 
III; sections 1 to 4 of part IV; section (1)(B) of part V; and parts IV 
and VI of Appendix B.
    (D) Previously approved on August 4, 1978 and now deleted without 
replacement Rules 300, 800, 1600, 1601, 1610 to 1612, 1620, 1700 to 
1701, 1710 to 1714, 1720 to 1725, 1730 to 1736, and Tables I to V.
    (v) Tuolumne County APCD.

[[Page 113]]

    (A) Rule 404.
    (B) New or amended Rules 102, 202, 203, 206, 207, 208, 209, 213, 
215, 216, 217, 301, 302, 303, 304, 308, 319, 321, 322, 323, 324, 402, 
407, 409, 601, 602, 603, 604, 605, 700, 701, 702, 703, 704, 705, 706, 
707, 708, 709, 710, 711, 712, 713, 714, 715, 716, and 717 and rescinded 
Rules 413 and 414.
    (C) Previously approved on December 6, 1979 and now deleted without 
replacement Rules 601 to 605, 700 to 704, and 705 to 716.
    (38) Revisions to air pollution emergency episode plans submitted on 
June 1, 1977 by the Governor's designee.
    (i) South Coast Air Quality Management District's Regulation VII 
Emergencies as revised on May 6, 1977. No action has been taken on those 
portions of Rules 702, 703, 704, 706, 708, 708.2, 710, 711, 712 and 714 
that pertain to sulfate, oxidant in combination with sulfate, or oxidant 
in combination with sulfur dioxide. No action has been taken on Rules 
708.2(b)(3)(B), 708.2(b)(4)(B), 708.2(b)(4)(C) and 708.2(b)(5)(C).
    (39) Revised regulations for the following APCDs submitted on June 
6, 1977, by the Governor's designee.
    (i) Great Basin Unified APCD.
    (A) Rule 403.
    (ii) San Bernardino County APCD (Southeast Desert portion).
    (A) Rule 430.
    (B) Rules 201-207, 209-212, 213, 213.1, 213.2, 214-217, and 219.
    (C) New or amended Rules 104, 106, 208, 218, 401, 403, 53-A(a), 407 
to 409, 431, 432, 441 to 443, 464 to 470, 472, 473, 475, 476, 503 to 
508, 510 to 518, 801 to 817.
    (D) Deleted without replacement Regulation VI--Orchard or Citrus 
Grove Heaters.
    (E) Rules 703, 704 (except those portions that pertain to the 
criteria levels for carbon monoxide and sulfur dioxide), 705, 706, 707, 
708, 709, 710, 711, 713, and 714.
    (F) Previously approved on September 8, 1978 and now deleted without 
replacement Rules 503 to 508, 510 to 516, 518, and 801 to 817.
    (iii) Los Angeles County APCD (Southeast Desert portion).
    (A) Rule 430.
    (B) Rules 201-207, 209-212, 213, 213.1, 213.2, 214-217, and 219.
    (C) New or amended Rules 101, 102, 2, 103 to 106, 208, 218, 301, 42, 
401, 403 to 405, 407 to 409, 431, 432, 441 to 444, 461, 463 to 476, 502 
to 518, 801 to 817.
    (D) Deleted without replacement Rule 53.1, and Regulation VI--
Orchard or Citrus Grove Heaters.
    (E) Rules 701, 702, 703, 704 (except those portions that pertain to 
the criteria levels for carbon monoxide and sulfur dioxide), 705, 706, 
707, 708, 709, 710, 711, 712, 713, 714, and 715.
    (F) Previously approved on September 8, 1978 and now deleted without 
replacement Rules 502 to 516, 518, and 801 to 817.
    (iv) Riverside County APCD (Southeast Desert portion).
    (A) Rule 430.
    (B) Rules 201-207, 209-212, 213, 213.1, 213.2, 214-217 and 219.
    (C) New or amended Rules 103, 104, 208, 218, 301, 42, 401, 403 to 
405, 53, 56, 407 to 409, 431, 432, 441 to 444, 463 to 476, 73, 503 to 
518, 801 to 817.
    (D) Deleted without replacement Regulation V--Orchard, Field or 
Citrus Grove Heaters.
    (E) Rules 702, 703, 704 (except those portions that pertain to the 
criteria levels for carbon monoxide and sulfur dioxide), 705, 706, 707, 
708, 709, 710, 711, 712, 713, 714, and 715.
    (F) Previously approved on September 8, 1978 and now deleted without 
replacement Rules 503 to 516, 518, and 801 to 817.
    (v) Yolo-Solano APCD.
    (A) Amended Rule 2.21.
    (vi) South Coast Air Quality Management District.
    (A) Amended Rule 461.
    (B) Amended Rule 431.
    (vii) Mariposa County APCD.
    (A) New or amended Rules 102(B), 102(E), 102(S), 102(II), 102(SS), 
203 (with the exception of (D)), 206(B), 207, 208, 211, 215, 216, 301, 
302, 303, 304, 308, 319, 320, 321, 322, 324, 402, 404, 407, 507, 514, 
600, 603, and 610.
    (B) Previously approved and now deleted (without replacement) Rule 
203(k).
    (C) Previously approved on June 6, 1977 and now deleted without 
replacement Rules 600, 603, and 610.
    (viii) Sierra County APCD.
    (A) New or amended Rules 102(B), 102(E), 102(S), 102(II), 102(SS), 
203 (with

[[Page 114]]

the exception of (D) and (G)), 206(B), 207, 208, 211, 215, 216, 301, 
302, 303, 308, 319, 320, 321, 322, 324, 402, 404, 407, 409, 507, 514, 
516, 600 to 617.
    (B) Previously approved and now deleted (without replacement) Rules 
203(j) and 620.
    (C) Previously approved on September 14, 1978 and now deleted 
without replacement Rules 601 to 602, 604 to 609, and 611.
    (D) Previously approved and now deleted, Rule 102.
    (ix) Plumas County APCD.
    (A) New or amended Rules 102(B), 102(E), 102(S), 102(II), 102(SS), 
203 (with the exception of (D) and (G)), 206(B), 207, 208, 211, 215, 
216, 301, 302, 303, 304, 307, 308, 319, 320, 321, 322, 324, 402, 404, 
407, 409, 507, 514, 602 to 605, 700, 703, and 710.
    (B) Previously approved on September 14, 1978 and now deleted 
without replacement Rules 602 to 605, 700, and 710.
    (C) Previously approved and now deleted, Rule 102.
    (x) Nevada County APCD.
    (A) New or amended Rules 102(B), 102(E), 102(S), 102(II), 102(SS), 
103, 104, 203(e and i), 206(B), 207, 216, 304, 319, 320, 321, 402, 407, 
409, 507, 514, 700, 703(E and I), 704, 710 and 711(A).
    (B) Previously approved on September 14, 1978 and now deleted 
without replacement Rules 704, 710, and 711(A).
    (C) Previously approved and now deleted, Rule 102.
    (40) [Reserved]
    (41) Revised regulations for the following APCD's submitted on 
October 13, 1977, by the Governor's designee.
    (i) Kings County APCD.
    (A) New or amended Rules 412 and 412.2.
    (ii) San Diego County APCD.
    (A) New or amended Rules 2(b), 2(t), 2(u), 2(v), 2(w), 3, 19.2, 40, 
42, 50, 52, 53, 54, 61.5, 64, 65, 66, 68, 71, 76, 77, 85, 95, 96, 
101(f), 102(d), 102(e), 103(d), 103(g), 104, 109, and 177.
    (1) Rule 65 is now removed without replacement as of March 14, 1989.
    (B) Previously approved and now deleted (without replacement) Rule 
113.
    (C) Regulation VIII, Rules 126-138 and Appendix A, except as these 
rules apply to the 12-hour carbon monoxide episode criteria specified in 
Rule 127.
    (D) Previously approved on August 31, 1978 and now deleted without 
replacement Rules 77, 85, and 96.
    (iii) Bay Area APCD.
    (A) New or amended rules: Regulation 1, section 3121 and Regulation 
2, sections 3210.5 to 3210.11.
    (iv) Ventura County APCD.
    (A) New Rule 105.
    (v) Kern County APCD.
    (A) Rule 108.
    (vi) San Luis Obispo County APCD.
    (A) New Rule 113.
    (vii) Monterey Bay Unified APCD.
    (A) New Rules 215, 422.
    (viii) Amador County APCD.
    (A) New or amended Rules 102(C), 102(F), 102(AW), 103, 205(A)(1), 
207, 212, 216, 302(A), 304, 305(C), 313(A), 507, 602.1, 604, 605, 701, 
703(E) and 710.
    (ix) Calaveras County APCD.
    (A) New or amended Rules 102, 203 (with the exception of (D) and 
(G)), 206(B), 207, 208, 209, 211, 215, 216, 217, 301, 302, 303, 304, 
319, 320, 321, 322, 323, 324, 402, 404, 407, 507, 602 to 604, 700, 702, 
703, 710, and 715.
    (B) Previously approved and now deleted (without replacement) Rule 
203(J).
    (C) Previously approved on November 7, 1978 and now deleted without 
replacement Rules 700, 702, 703, 710, 715.
    (x) Placer County APCD.
    (A) New or amended Rules 101, 102, 103, 104, 203 (with the exception 
of (G)), 206, 207, 208, 210, 211, 213, 214, 301 to 311, 313 to 322, 401, 
402, 404, 407, 408, 409, 507, 603 to 605, 702 to 704, 706, 708, 709, 
710, 715, 801 to 804.
    (B) Previously approved on November 15, 1978 and now deleted without 
replacement Rules 703, 704, 708 to 710, and 715 (Mountain Counties Air 
Basin).
    (C) Previously approved on November 15, 1978 and now deleted without 
replacement Rules 603 to 605, 702 to 704, 706, 708 to 710, and 715 (Lake 
Tahoe Air Basin).
    (xi) Tulare County APCD.
    (A) New or amended Rules 108 and 412.1
    (xii) Shasta County APCD.
    (A) New or amended Rules 1:2 (with the exception of the definition 
of ``person''); 2:6(1)(a), (1)(b), (i-ii), (1)(b)(iii), (a, b, and d), 
(1)(b), (iv-vii), (1)(c), (i-vi and viii), (1) (d and e), (2) (a-d and 
f), (3) (a-c and e-g), (4) (a-c and e-i), (5) (b-d);

[[Page 115]]

2:7, 2:8; 3:2 (except part VI and VII of table II, and explanatory notes 
6 and 7); 3:4, 4:1, 4:5, 4:6, 4:14, and 4:19.
    (B) Previously approved on November 14, 1978 and now deleted without 
replacement Rules 4.5 and 4.6.
    (xiii) Madera County APCD.
    (A) Amended Rule 412.1.
    (xiv) South Coast Air Quality Management District.
    (A) New or amended Rules 101 and 102 (except for the definition of 
``agricultural burning'').
    (xv) Northern Sonoma County APCD.
    (A) New or amended Rules 420(e) and (f), and 455(a) and (d).
    (42) Revised regulations for the following APCD's submitted on 
November 4, 1977 by the Governor's designee.
    (i) Imperial County APCD.
    (A) New or amended Rules 100 to 110, 113 to 115, 301 to 303, 305, 
401, 403 to 406, 408, 409, 411 to 416, 419 to 422, 501 to 516, and 701 
to 706.
    (B) Previously approved and now deleted (without replacement), Rules 
106B, 113, 126, 131 and 147.
    (C) Rules 601, 602 (except those portions that pertain to the 
criteria levels for carbon monoxide and sulfur dioxide), 603, 604, 605, 
606, 607, 608, 609, 610, 611, 612, 613, and 614.
    (D) New Rule 417 (A-H, and J).
    (E) Previously approved on August 11, 1978 and now deleted without 
replacement Rules 501 to 512 and 514 to 516.
    (ii) Sacramento County APCD.
    (A) Rules 3, 7(a) to 7(b)(2), 7b(4) to 7(d), 9, 11, 12, 13, 14, 15, 
21, 22a, 23, 24, 25, 26, 94, 95, 96, 97, and 98.
    (B) Rules 120, 121, 122, 125, and 126, except those portions that 
pertain to the 12-hour CO criteria level.
    (iii) Kings County APCD.
    (A) New or amended Rules 102, 103, 103.1, 104, 105, 108, 108.1, 110, 
111, 112, 113, 401, 402(a) to 402(d), 402(f), 402(g), 404, 404.1, 405, 
405.1, 405.2, 405.3, 406, 407.1, 409, 410, 416.1, 417, 417.1, 418, 421, 
and 501.
    (B) Previously approved and now deleted, Rule 405.1.
    (C) Previously approved on August 4, 1978 and now deleted without 
replacement Rules 105 and 501.
    (iv) Stanislaus County APCD.
    (A) New or amended Rules 103.1, 108, 411.1.
    (v) Merced County APCD.
    (A) Amended Rules 411(b) and 411.1.
    (vi) Kern County APCD.
    (A) Rule 412.1.
    (vii) San Luis Obispo County APCD.
    (A) New or amended Rules 105(A)(1), 407, 501(A)(7), 502(A)(3).
    (viii) Glenn County APCD.
    (A) New or amended Rules 82, 152, and 154.
    (ix) Great Basin Unified APCD.
    (A) New or amended Rules 300, 423, and 617.
    (B) Previously approved and now deleted (without replacement) Rules 
411 and 418.
    (x) El Dorado County APCD.
    (A) New or amended Rules 102, 201, 203 [with the exception of (G)], 
206(B), 207, 208, 215, 216, 217, 217-49 to 217-50, 217-51(A to D), 217-
53 to 217-56, 217-1 to 217-3, 302, 303, 304, 307, 308, 319, 320, 321, 
322, 324, 402, 407, 409, 507, 700, 703 and 710.
    (xi) Fresno County APCD.
    (A) New or amended Rules 411.1 and 416.1(g).
    (xii) San Joaquin County APCD.
    (A) New or amended Rules 108 and 411.2.
    (xiii) San Bernardino County Desert APCD.
    (A) New or amended Rules 101, 102, 103, 105, 404, 405, 406(a), 444, 
461, 462, 463, 471, 474, 501, 502 and 509.
    (B) Previously approved and now deleted without replacement Rules 44 
and 53.1.
    (C) Rules 701, 702, 712, and 715.
    (D) Previously approved on December 21, 1978 and now deleted without 
replacement Rules 501, 502, and 509.
    (xiv) Riverside County APCD.
    (A) New or amended Rules 101, 102, 105, 461, and 501.
    (B) Rule 701.
    (C) Previously approved on December 21, 1978 and now deleted without 
replacement Rule 501.
    (xv) Del Norte County APCD.
    (A) New or amended Rules 240(e), 420 (e) and (f), and 455 (a) and 
(d), and Appendix D to regulation 1.
    (xvi) South Coast Air Quality Management District.
    (A) New or amended Rules 218, 463, and 466.
    (B) Rules 702 (map only) and 708.2.

[[Page 116]]

    (C) Rules 714 and 715.1 (except those portions that pertain to 
sulfate, oxidant in combination with sulfate, and oxidant in combination 
with sulfur dioxide).
    (xvii) Humboldt County APCD.
    (A) New or amended Rules 240(e), 420 (e) and (f), and 455 (a) and 
(d), and Appendix D to Regulation 1.
    (xviii) Santa Barbara County APCD.
    (A) New Rule 39.3.
    (xix) Mendocino County APCD.
    (A) New or amended Rules 240(e), 420 (e) and (f), and 455 (a) and 
(d), and Appendix D to Regulation 1.
    (xx) Trinity County APCD.
    (A) New or amended Rules 240(e), 420 (e) and (f), and 455 (a) and 
(d), and Appendix D to Regulation 1.
    (xxi) Northern Sonoma County APCD.
    (A) New or amended Rules 240(e), 310, and Appendix D to Regulation 
1.
    (xxii) Monterey Bay Unified APCD.
    (A) Regulation VII, Rules 700-713.
    (43) [Reserved]
    (44) Revised regulations for the following APCD's submitted on June 
22, 1978, by the Governor's designee.
    (i) Great Basin Unified APCD.
    (A) Amended Rule 419.
    (ii) Santa Barbara County APCD.
    (A) New Rule 24.15.
    (iii) Ventura County APCD.
    (A) New or amended Rules 2, 7, and 56 (with the exception of 
Sections B(2)(c) and C).
    (iv) Yolo-Solano APCD.
    (A) Amended Rules 1.2 (preamble), 1.4, 2.8(c)(2), 2.13(h)(4), 2.15, 
2.17, 2.20, 4.4(b), 5.1, 5.4(e)(1), 5.10, 5.11, and 6.7(f).
    (B) Previously approved and now deleted (without replacement) Rule 
2.8(b)(4).
    (C) Previously approved on January 29, 1979 and now deleted without 
replacement Rules 5.1, 5.10 and 5.11.
    (v) South Coast Air Quality Management District.
    (A) Rules 102, 501.1, and 503.
    (B) Previously approved on March 28, 1979, and now deleted without 
replacement Rule 503.
    (vi) San Diego County APCD.
    (A) New or amended Rules 66, 67.0, and 67.1.
    (45) Revised regulations for the following APCD's submitted on July 
13, 1978 by the Governor's designee.
    (i) Bay Area APCD.
    (A) New or amended Regulation 2, Division 3, sections 3210.11(B), 
3211.2; Regulation 3, Division 3, Sec. 3102.1; Regulation 9.
    (ii) South Coast AQMD.
    (A) Rules 302, 461, 465, 1102, and 1113.
    (iii) San Diego County APCD.
    (A) New or amended Rules 42, 76, and 97.
    (B) Previously approved on July 30, 1979 and now deleted without 
replacement Rules 76 and 97.
    (46) The following Administrative Chapters of the California SIP, 
submitted on December 29, 1978, by the Governor's designee.
    (i) Chapter 2--Statewide Perspective.
    (ii) Chapter 20--Compliance.
    (iii) Chapter 23--Source Surveillance.
    (iv) Chapter 24--Resources.
    (v) Chapter 25--Intergovernmental Relations.
    (47) Revised regulations for the following APCD's submitted on 
January 2, 1979 by the Governor's designee.
    (i) South Coast AQMD.
    (A) New or amended Rules 301, 303, 708.3, 1201-1206, 1209-1211, 
1214, 1217, 1220-1221, 1223-1224 and 1231.
    (B) New or amended Rules 462, 481, and 1104.
    (ii) Fresno County APCD.
    (A) New or amended Rules 110, 416.1, and 519.
    (B) New or amended Rule 409.1.
    (iii) Kern County APCD.
    (A) New or amended Rules 111, 301, and 519.
    (B) Rule 412.
    (iv) Lake County APCD.
    (A) New or amended Rules 435, and 436, and Tables V and VI.
    (v) Monterey Bay Unified APCD.
    (A) Amended Rule 301.
    (vi) Siskiyou County APCD.
    (A) Amended Rule 4.3.
    (vii) San Luis Obispo County APCD.
    (A) Rule 407.
    (B) New or amended Rule 201.
    (48) Chapter 3--Legal Authority of the California SIP, submitted on 
March 16, 1979, by the Governor's designee.
    (49) Addendum to Chapter 23 of the California SIP submitted on March 
29, 1979, by the Governor's designee.
    (50) Revised regulations for the following APCD's submitted on May 
7, 1979, by the Governor's designee.

[[Page 117]]

    (i) Del Norte County APCD.
    (A) New or amended Rules 240, 410 (a) and (c), and 615.
    (B) Previously approved on October 31, 1980 and now deleted without 
replacement Rule 615.
    (ii) Humboldt County APCD.
    (A) New or amended Rules 240, 410 (a) and (c), 615.
    (B) Previously approved on October 31, 1980 and now deleted without 
replacement Rule 615.
    (iii) Mendocino County APCD.
    (A) New or amended Rules 240, 410, and 615.
    (B) Previously approved on October 31, 1980 and now deleted without 
replacement Rule 615.
    (iv) Trinity County APCD.
    (A) New or amended Rules 240, 410 (a) and (c), and 615.
    (B) Previously approved on October 31, 1980 and now deleted without 
replacement Rule 615.
    (v) Northern Sonoma County APCD.
    (A) New or amended Rules 240, 300, 310, 320, 410 (a) and (c), 420, 
540, 615.
    (B) Previously approved on October 31, 1980 and now deleted without 
replacement Rules 320 and 615.
    (vi) Merced County APCD.
    (A) New or amended Rule 409.1.
    (B) New or amended Rule 519.
    (vii) Modoc County APCD.
    (A) New or amended Rules 1:2 w, 2:11, 2:15, 3:3 and 3:4.
    (viii) Monterey Bay Unified APCD.
    (A) Rules 403 and 602.
    (ix) Ventura County APCD.
    (A) New or amended Rules 71 and 71.3.
    (B) New or amended Rule 11.
    (x) San Diego County APCD.
    (A) New or amended Rule 10(h) and deletion of Rule 43.
    (51) Revised regulations for the following APCD's submitted May 23, 
1979, by the Governor's designee.
    (i) Kern County APCD.
    (A) Amended Rules 305 and 503.
    (B) Rules 410.1 and 424.
    (C) Previously approved on August 11, 1980 and now deleted without 
replacement Rule 503 (including Southeast Desert).
    (ii) Monterey Bay Unified APCD.
    (A) Rule 417.
    (B) Rule 617.
    (iii) Del Norte County APCD.
    (A) New or amended Rules 130, 300, 310, 320, 420, 540 and Regulation 
1/Appendix D.
    (B) Previously approved on October 31, 1980 and now deleted without 
replacement Rule 320.
    (iv) Humboldt County APCD.
    (A) New or amended Rules 130, 300, 310, 320, 420, 540 and Regulation 
1/Appendix D.
    (B) Previously approved on October 31, 1980 and now deleted without 
replacement Rule 320.
    (v) Mendocino County APCD.
    (A) New or amended Rules 130, 300, 310, 320, 420, 540 and Regulation 
1/Appendix D.
    (B) Previously approved on October 31, 1980 and now deleted without 
replacement Rule 320.
    (vi) Trinity County APCD.
    (A) New or amended Rules 130, 300, 310, 320, 420, 540 and Regulation 
1/Appendix D.
    (B) Previously approved on October 31, 1980 and now deleted without 
replacement Rule 320.
    (vii) San Diego County APCD.
    (A) Amended Rules 2(t), 61.5, and 61.7.
    (B) New or amended Rules 19.2(d)(4), 50, 62(a), 66(P) and (W), 95, 
and 98.
    (C) New or amended Rule 11.
    (D) Previously approved on September 28, 1981 and now deleted 
without replacement Rules 95 and 98.
    (viii) San Joaquin County APCD.
    (A) New or amended Rule 409.1.
    (B) New or amended Rules 110 (a), (b), and (d)-(i), 301, 303-311, 
and 511.
    (C) New or amended Rules 102, 108.2, 110(c), 302, 401, and 521.
    (D) Previously approved on December 9, 1981 and now deleted without 
replacement Rules 301, 303 to 311, and 511.
    (E) Previously approved on June 18, 1982 and now deleted without 
replacement Rule 302.
    (ix) Stanislaus County APCD.
    (A) New or amended Rule 409.1.
    (B) New or amended Rule 110 (A), (B) and (D)-(I).
    (C) New or amended Rules 110(c) and 519.
    (D) Previously approved on June 18, 1982 and now deleted without 
replacement Rule 519.
    (x) Tulare County APCD.
    (A) New or amended Rules 410.1 and 413.

[[Page 118]]

    (B) New or amended Rules 111 (a), (b), and (d)-(i), 402, and 417.
    (C) New or amended Rules 108, 111(c), 201, 410 and 519.
    (xi) Lake County APCD.
    (A) New Rules 227.1, 254.1, and 660.
    (xii) San Bernardino County Desert APCD.
    (A) New Rules 480 and 501.1.
    (B) New or amended Rules 442, 463, and 1113.
    (C) Previously approved on January 27, 1981 and now deleted without 
replacement Rule 501.1.
    (xiii) Santa Barbara County APCD.
    (A) New or amended Rules 101, 102, 103, 104, 201(A, B, D, E, F, and 
G), 202, 203, 204, 205(A and B), 206, 207, 208, 209, 210, 211, 301, 302, 
304, 305, 306, 307, 308, 309, 311, 312, 313, 314, 315, 317, 319, 322, 
324, 328, 401, 402, 403, 501, 502, 503, 504, 505, 505-A, 506, 507, 508, 
509, 510, 511, 512, 513, 514, 515, 516, 517, 518, 519, 601, 602, 603, 
604, 605, 606, 607, 608, 609, and 610.
    (B) Previously approved on May 18, 1981 and now deleted without 
replacement Rules 210 to 211, 501 to 504, 506 to 512, 514 to 516, and 
518.
    (xiv) El Dorado County APCD--Lake Tahoe Air Basin Portion.
    (A) New or amended Rules 101, 102 (except LAER, stationary source, 
modification definitions), 103, 104, 201-203, 206A-212, 217, 301-305, 
307-310, 312-321, 404, 702-704, 706-710, and 801-804. Deleted Rules 
59(g)(1), 102I, 102S, 102BB, 102FF, 102GG, 102LL, 102RR, 208, 214, 601, 
602, and 700.
    (B) Amended Rule 306.

    Editorial Note: At 47 FR 27068, June 23, 1982, the following 
paragraph (c)(51)(xiv)(B) was added to Sec. 52.220.

    (B) New or amended Rules 102, LAER, stationary source, and 
modifications; 213; and 214.
    (xv) Placer County APCD--Mountain Counties Air Basin Portion.
    (A) New or amended Rules 404, 602, and 603.
    (B) Deletion of Rules 604 and 605.
    (C) Previously approved on May 18, 1981 and now deleted without 
replacement Rules 404, 602, and 603.
    (xvi) Sacramento County APCD.
    (A) Amended Rule 71.
    (B) Previously approved on January 26, 1982 and now deleted without 
replacement Rule 71.
    (xvii) Shasta County APCD.
    (A) Amended Rule 3.4.
    (xviii) Sierra County APCD. (A) New or amended Rules 207, 210, 211, 
218 and 618.
    (xix) Tehama County APCD.
    (A) Amended Rule 2.1 and previously approved and now deleted Rule 
2.9 (Action on Applications).
    (xx) Ventura County APCD.
    (A) New or amended Rules 6, 8, 9, 13, 24, 40, 63, 75, 102, 103, 110, 
111, 112, 113, 114, 120, 121, 123, 124, 125, 126, 127, and 130.
    (B) Previously approved on June 18, 1982 and now deleted without 
replacement Rules 40, 110, 120 to 121, 123 to 126, and 130.
    (52) Revised regulations for the following APCD's submitted October 
15, 1979, by the Governor's designee.
    (i) Kern County APCD.
    (A) Amended Rule 302
    (B) Rules 410.4, 410.5, and 414.2.
    (ii) Imperial County APCD.
    (A) Rules 415.1 and 424.
    (B) New or amended Rules 101 L, 110, 201B, 301, 302, 304, 306, 401, 
404, 406, 408, 410, 417 I, 418, 419, 422, Regulation VI, 701, 702, 703 
(deletion), 705, and 706.
    (iii) [Reserved]
    (iv) Kings County APCD.
    (A) New or amended Rules 210.1 (except paragraphs (3)(D) and 
(5)(B)(8)), 210.2, 410.1, 410.2, 410.3, 410.5, 412.1, 413, 414.1, and 
414.2.
    (B) New or amended Rules 111 (A), (B), and (D)-(I), 301, 302, and 
401.
    (C) New or amended Rules 111(c), and 519.
    (D) Previously approved on October 9, 1981 and now deleted without 
replacement Rule 302.
    (E) Previously approved on June 18, 1982 and now deleted without 
replacement Rule 519.
    (v) Madera County APCD.
    (A) New or amended Rules 210.2, 410.1, 410.3, 410.5, 411, and 412.
    (B) New or amended Rules 102, 103, 103.1, 104, 105, 108, 108.1, 110, 
115, 210.3, 301, 305, 402(a)-(e), 409, 410, 416, 417, 418, 501, 504, 
511, 601, 602, 603, 606-611, and 612.
    (C) New or amended Rules 111(c) 402(f) and 519.
    (vi) Merced County APCD.
    (A) New or amended Rules 210.1 (except paragraphs (3)(D) and 
(5)(B)(8)), 210.2, 409.5, and 411.

[[Page 119]]

    (B) New or amended Rules 109 (A), (B), and (D)-(I).
    (C) New or amended Rule 109(c).
    (vii) San Joaquin County APCD.
    (A) New or amended Rules 209.1 (except paragraphs (B)(3) and 
(D)(2)(b)), 209.2, 409.3, 410, 411.1, 413, 413.1, 413.2, and 413.3.
    (B) New or amended Rule 209.3.
    (C) New or amended Rule 209.4.
    (viii) Stanislaus County APCD.
    (A) New or amended Rules 209.2 and 411.
    (ix) Tulare County APCD.
    (A) New or amended Rules 210.1 (except paragraphs (C)(4) and 
(e)(2)(H)), 210.2 and 410.5.
    (B) New or amended Rules 301 and 302.
    (C) Previously approved on December 9, 1981 and now deleted without 
replacement Rules 301 and 302.
    (x) Lake County APCD.
    (A) Amended Rule 433.
    (xi) Amador County APCD.
    (A) New or amended Rules 102, 103, 107, 203, 206B, 207, 209-211, 
213, 215, 216, 301-313, 315-324, 401, 402, 404, 407, 409, Regulation VI, 
700-704, 710, and 711.
    (B) Previously approved on May 18, 1981 and now deleted without 
replacement Rules 605, 700 to 704, and 710 to 711.
    (xii) Nevada County APCD.
    (A) New or amended Rules 207, 210, 211, 218, 306, 307, and 404.
    (B) Previously approved on May 18, 1981 and now deleted without 
replacement Rule 404.
    (xiii) Placer County APCD--Mountain Counties Air Basin Portion.
    (A) New or amended Rules 101, 102, 104, 201, 202, 207, 210, 211, 
220-222, 301-310, and 312-323.
    (B) New or amended Rules 215 and 219.
    (C) Rule 508 (except paragraph (c)(3)(h)).
    (D) New or amended Rules 501B, 502, 504, 506, 512, and 513.
    (E) Previously approved and now deleted, Rule 104.
    (xiv) Tuolumne County APCD.
    (A) New or amended Rules 207, 210, 218, and 404.
    (xv) Fresno County APCD.
    (A) New or amended Rules 210.1 [except paragraphs (3)(D) and 
(5)(B)(8)], 210.2, 409.5, 409, 409.3, 409.4, and 411.
    (B) New or amended Rules 301, 302, and 305.
    (C) Previously approved on December 9, 1981 and now deleted without 
replacement Rule 305.
    (xvi) Yuba County APCD.
    (A) New or amended Rules 1, Section 1 (except Silviculture 
Deletion), 1.1 (except PPM), 2.0-2.2, 2.4 except (a), 2.5-2.12, 2.15-
2.20, 2.22-2.24, 2.27, 2.30, Section 5 (Deletion), 5.0-5.3, 5.5-5.19, 
6.1-6.7, 7, 7.1 and 8.1.
    (B) New or amended Rules 2.3 and 2.4(a).
    (xvii) San Diego County APCD.
    (A) New or amended Rule 67.7 and 67.2.
    (xviii) Shasta County APCD.
    (A) New or amended Rules 1.1, 1.2, 2.11, 2.12, and 3.2 (except rows 
(vi) and (vii)).
    (B) Amended Rule 2:5.
    (xix) Yolo--Solano APCD.
    (A) New or amended Rules 4.1-4.3.
    (B) New or amended Rules 301, 302, and 305.
    (C) Previously approved on January 26, 1982 and now deleted without 
replacement Rule 4.3.
    (xx) Sacramento County APCD.
    (A) New or amended Rule 1.
    (xxi) Siskiyou County APCD.
    (A) New or amended Rules 2.14-2.16.
    (53) Revisions to air pollution emergency episode plans submitted on 
February 14, 1980 by the Governor's designee.
    (i) Bay Area Air Quality Management District Rules 100, 101, 300, 
301, 302, 303, 304, 305, 400, 401, 402, 403, and 404.
    (54) Revised regulations for the following APCD's submitted on 
February 25, 1980, by the Governor's designee.
    (i) Ventura County APCD.
    (A) Rules 150, 152, 153, 154, 155, 156, 157, 158, 159, 160, 161, and 
162.
    (B) New or amended Rule 71.1.
    (C) New or amended Rules 56, 80, 81, and deletion of Rules 17, 151, 
163, and 164.
    (ii) Monterey Bay Unified APCD.
    (A) Rule 422 and deletion of Rule 508.
    (B) Amended Rule 416.
    (iii) San Luis Obispo County APCD.
    (A) Rules 301, 302, 303, and 304.
    (B) Previously approved on May 18, 1981 and now deleted without 
replacement Rules 303 and 304.
    (iv) Yolo--Solano APCD.

[[Page 120]]

    (A) Amended Rule 5.4.
    (B) New or amended Rules 2.21, 2.21.1, 2.24 and 2.25.
    (C) New or amended Rule 3.13.
    (D) Previously approved on January 26, 1982 and now deleted without 
replacement Rule 5.4.
    (v) Sacramento County APCD.
    (A) New or amended Rule 17.
    (B) [Reserved]
    (C) New or amended Rules 3.13, 3.4.1, and 3.4.2.
    (vi) Sutter County APCD.
    (A) New or amended Rules 1.4, 2.8.1 (Deletion), 2.17, and 2.82.
    (vii) Yuba County APCD.
    (A) Amended Rule 2.26.
    (viii) Butte County APCD.
    (A) New Rule 2-12.e.
    (B) Amended Rules 4.5A and 4.5B.
    (ix) Tehama County APCD.
    (A) Amended Rules 2.5A and 2.5B.
    (x) Colusa County APCD.
    (A) New or amended Rules 2.7 A and B.
    (xi) Glenn County APCD.
    (A) New or amended Rules 51.1 and 51.2.
    (xii) Shasta County APCD.
    (A) New or amended Rules 1:2 (Best Available Control Technology, 
Stationary Source and Precursor) and 2:1 A.
    (55) The following material for Imperial County was submitted on 
October 11, 1979 by the Governor's designee.
    (i) Summary of Plan Compliance with Clean Air Act Requirements.
    (ii) Imperial County plan to attain National Ambient Air Quality 
Standards for oxidants, October 31, 1978.
    (iii) SIP Revision--Imperial County ARB Staff Report, No. 79-4-2.
    (iv) ARB resolution 79-9, February 21, 1979.
    (v) Copies of Board hearing testimony.
    (56) Revised regulations for the following APCDs submitted on March 
17, 1980, by the Governor's designee.
    (i) Imperial County APCD.
    (A) Rules 207 [except Subparagraph C.4.], 208, and 209.
    (ii) Ventura County APCD.
    (A) Amended Rule 26.3.
    (B) New or amended Rules 10, 25, and 27.
    (57) The North Central Coast Air Basin Strategy (Chapter 10 of the 
comprehensive revisions to the State of California Implementation Plan 
for the Attainment and Maintenance of Ambient Air Quality Standards) 
submitted on September 12, 1979 by the Governor's designee.
    (58) Revised regulations for the following APCDs submitted on 
December 17, 1979 by the Governor's designee.
    (i) Monterey Bay Unified APCD.
    (A) Rules 418, 425 and 426.
    (B) New or amended Rules 300, 405, and 601.
    (ii) South Coast AQMD.
    (A) New or amended Rules 1107, 1108, 1108.1 and 1128.
    (B) New or amended Rules 404, 442, 501.1, 502, 504.1(b), (c), and 
(d), and 1124.
    (C) Previously approved on September 28, 1981 and now deleted 
without replacement Rule 501.1.
    (iii) Great Basin Unified APCD.
    (A) New or amended Rules 205, 210, 300A, and G, 403, 408, 419, and 
617.
    (B) New or amended Rules 203, 209-A and B, 212, and 213.
    (iv) Ventura County APCD.
    (A) New or amended Rule 74.3.
    (v) Butte County APCD.
    (A) New or amended Rules 2.12a, 2.12b, 2.12c, and 2.12d.
    (vi) Shasta County APCD.
    (A) New or amended Rules 1.2, 3.14, and 3.15.
    (vii) Yolo--Solano APCD.
    (A) Amended Rules 2.8 and 6.6.
    (viii) San Luis Obispo County APCD.
    (A) New or amended Rule 407.
    (ix) Modoc County APCD.
    (A) New or amended Rule 2:8-e.
    (59) Revised regulations for the following APCD submitted on March 
4, 1980 by the Governor's designee.
    (i) Monterey Bay Unified APCD.
    (A) Rules 207 (except B.4.) and 208.
    (B) New or amended Rules 205, 211, 212, 213, and 214.
    (60) Chapter 4, California Air Quality Control Strategies, of the 
California SIP, submitted on May 23, 1979, by the Governor's designee.
    (61) Redesignation of AQCR's in California, submitted on September 
11, 1978, by the Governor's designee.
    (62) The San Diego Air Basin Control Strategy (Chapter 14 of the 
Comprehensive Revisions to the State of California Implementation Plan 
for the Attainment and Maintenance of Ambient Air Quality Standards) 
submitted on

[[Page 121]]

July 5, 1979, by the Governor's designee, except the inspection/
maintenance portion. Additional documents were also submitted as 
appendices. Those portions of the San Diego Air Basin Control Strategy, 
including Appendices, identified by Table 14-1, ``Location of Plan 
Elements Which Meet Clean Air Act Requirements'' (pages 6-7), comprise 
the submitted nonattainment area plan, except the inspection/maintenance 
portion. The remaining portions are for informational purposes only.
    (63) The following portions of the California Environmental Quality 
Act submitted on October 20, 1980, by the Governor's designee: Sections 
21000; 21001; 21002; 21002.1; 21061; 21063; 21065; 21080.1; 21080.4; 
21080.5 (a), (b), (c) and (d); 21081; 21082; 21100; 21104; 21151; 21153; 
21160.
    (64) Revised regulations for the following APCD submitted on 
February 13, 1980, by the Governor's designee.
    (i) San Diego County APCD.
    (A) Rules 20.1, 20.2, 20.3, 20.4, 20.5 and 20.6.
    (65) The following amendments to the plan were submitted on July 25, 
1979, by the Governor's designee.
    (i) The South Coast Air Basin Control Strategy (Chapter 18 of the 
Comprehensive Revision to the State of California Implementation Plan 
for the Attainment and Maintenance of Ambient Air Quality Standards). 
Those portions of the South Coast Air Basin Control Strategy identified 
by Table 18-1, ``Location of Plan Elements Which Meet Clean Air Act 
Requirements,'' together with Rules 1115 and 1126, comprise the 
submitted nonattainment area plan control strategy. The remaining 
portions are for informational purposes only.
    (ii) New or amended Rules 218, 431, 431.1-431.3, 1120, 1206-1208, 
1212, 1213, 1215, 1216, 1218, 1219, 1222, and 1225-1230.
    (66) Revised regulations for the following APCD's, submitted on 
February 7, 1980, by the Governor's designee.
    (i) South Coast AQMD.
    (A) New or amended Rule 461.
    (B) Amended Rule 466.
    (ii) Bay Area AQMD.
    (A) Regulation 8: Rule 1, 2 (except paragraph 301), 4, 7, 8, 9, 10, 
11, 13, 14, 15, 16, 18 and 19.
    (67) Revised regulations for the following APCD's, submitted on 
April 2, 1980, by the Governor's designee.
    (i) South Coast AQMD.
    (A) New or amended Rule 1122.
    (B) New or amended Rules 107, 709(c), 1111, 1121 and 1140.
    (ii) Bay Area AQMD.
    (A) New or amended Regulation 9, Rules 9-4-100, 9-4-101, 9-4-200 to 
9-4-203, 9-4-300, 9-4-301, 9-4-303, and 9-4-400 to 9-4-404.
    (iii) Kern County APCD.
    (A) New or amended Rules 412.1(b)-(f).
    (B) New Rule 411.1.
    (iv) Sacramento County APCD.
    (A) New or amended Rules 7, 24, 25, 28, 30, and 53.
    (B) New or amended Rules 120, 121, and 122.
    (68) Revised regulations for the South Coast AQMD, submitted on 
April 3, 1980, by the Governor's designee.
    (i) New or amended Rules 1301, 1303, 1304, 1305, 1306, 1307, 1310, 
1311, and 1313.
    (69) Revised regulations for the South Coast AQMD submitted on April 
23, 1980, by the Governor's designee.
    (i) New or amended Rules 464, 465, 1123, and 1125.
    (ii) New or amended Rules 301, 405, 431.2(c)(5), 701, 702 (a), (d), 
(e), (f), (h) and (i), 703-706, 708.3(a), (b)(8)-(b)(10), 708.4(g) and 
(h), 709(a), 710(a) and (b)(4), 711(a)(1), (a)(4), (b)(1) and (b)(4), 
and 713-715.
    (iii) New Rule 1103.
    (iv) California Health and Safety Code, Sections 41950 to 41962, 
94000 to 94004; and Stationary Source Test Methods--Volume 2: 
Certification and Test Procedures for Gasoline Vapor Recovery Systems 
submitted on April 23, 1980.
    (70) Revised regulations for the following APCD's submitted on 
August 15, 1980, by the Governor's designee.
    (i) South Coast AQMD.
    (A) New or amended Rules 1302 and 1308.
    (B) New or amended Rule 1101.
    (C) New or amended Rules 702(b), 707, 708, 708.3 (a)(2) and (c), 
708.4 (a) and (b), 709(e), 710 (b)(1)(D), (b)(2)(D), (b)(3)(B), and 
(c)(3)(B), 711 (a)(1)(E), (a)(2)(D), (a)(3)(B), (a)(4)(F), (b)(3)(B), 
and (b)(4)(f), and 1102.
    (D) Amended Rule 401 (except subparagraph 401(b)).

[[Page 122]]

    (ii) San Diego County APCD.
    (A) New or amended Rules 2 (z) and (aa), 40, and 10 (f) and (i).
    (iii) Shasta County APCD.
    (A) Amended Rule 3.3.
    (iv) El Dorado County APCD (Mountain Counties and Lake Tahoe Air 
Basin).
    (A) New or amended Rules 601-613.
    (71) The San Joaquin Valley Air Basin Control Strategy (Chapter 16 
of the Comprehensive Revisions to the State of California Implementation 
Plan for the Attainment and Maintenance of Ambient Air Quality 
Standards) submitted on October 11, 1979, by the Governor's designee. 
Those portions of the San Joaquin Valley Air Basin Control Strategy 
identified by Tables 16-1a, 1b and 1c (Summary of Plan Compliance with 
Clean Air Act Requirements) except which pertain to Fresno County and 
the sixtransportation control measures for Stanislaus County, comprise 
the submitted plan. The remaining portions are for informational 
purposes only. The following rules were also submitted on October 11, 
1979 as part of the enforceable plan:

    Editorial Note: At 47 FR 28620, July 1, 1982, the following 
introductory text to paragraph (c)(71) was added to Sec. 52.220.

    (71) The San Joaquin Valley Air Basin Control Strategy (Chapter 16 
of the Comprehensive Revisions to the State of California Implementation 
Plan for the Attainment and Maintenance of Ambient Air Quality 
Standards) submitted on October 11, 1979, by the Governor's designee. 
Those portions of the San Joaquin Valley Air Basin Control Strategy 
identified by Tables 16-1a, 1b and 1c (Summary of Plan Compliance with 
the Clean Air Act Requirements) comprise the submitted plan. The 
remaining portions are for informational purposes only.
    (i) Kings County APCD.
    (A) New or amended Rules 411 and 413.3.
    (ii) Madera County APCD.
    (A) New or amended Rule 210.1 (except paragraphs (3)(D) and 
(5)(B)(8)).
    (iii) Merced County APCD.
    (A) New or amended Rules 409.3 and 410.
    (iv) Tulare County APCD.
    (A) New or amended Rule 410.3.
    (72) The San Francisco Bay Area Basin Control Strategy (Chapter 15 
of the Comprehensive Revisions to the State of California Implementation 
Plan for the Attainment and Maintenance of Ambient Air Quality 
Standards) including appendices, submitted on July 25, 1979, by the 
Governor's designee.
    (73) Revised regulations for the following APCD's submitted on 
January 14, 1980, by the Governor's designee.
    (i) Bay Area AQMD.
    (A) Regulation 2: Rule 1: 2-1-200, 2-1-300, 2-1-307, and 2-1-400, 
Rule 2: 2-2-100, 2-2-200, 2-2-209, 2-2-210, 2-2-300, and 2-2-400; Rule 
3: 2-3-100, 2-3-101, 2-3-200, 2-3-201, 2-3-300, 2-3-301, 2-3-302, 2-3-
401, 2-3-401.1 to 2-3-401.3, 2-3-402, 2-3-403, 2-3-404, and 2-3-405.
    (B) New or amended Regulation 2, Rule 1: 2-1-100 to 2-1-102, 2-1-
111, 2-1-112, and 2-1-408.
    (74) Revised regulations for the following APCD's submitted on 
December 24, 1979, by the Governor's designee.
    (i) Imperial County APCD.
    (A) New or amended Rules 111, 413, 414, 416, 416 (deletion), and 
517.
    (B) Previously approved on January 27, 1981 and now deleted without 
replacement Rule 517.
    (ii) Santa Barbara County.
    (A) Rule 316.
    (iii) Ventura County APCD.
    (A) New Rule 70 (except paragraph E).
    (75) Revised regulations for the Kern County APCD, submitted on 
January 8, 1980, by the Governor's designee.
    (i) Rules 210.2, 410.3, 411, 414, 414.1, and 414.3.
    (ii) New or amended Rule 424(F).
    (76) Revised regulations for the following APCD's, submitted on 
April 15, 1980, by the Governor's designee.
    (i) Kern County APCD.
    (A) Amended Rule 210.1
    (77) The following amendments to the plan were submitted on October 
18, 1979, by the Governor.
    (i) San Luis Obispo County APCD.
    (A) New or amended Rules 415, 416, 420, and 422.
    (ii) The South Central Coast Air Basin Control Strategy [Chapter 17 
of the Comprehensive Revision to the State of California Implementation

[[Page 123]]

Plan for the Attainment and Maintenance of Ambient Air Quality 
Standards]. Those portions of the South Central Coast Air Basin Control 
Strategy identified by Tables 17-1 and 17-2 ``Location of Plan Elements 
Which Meet Clean Air Act Requirements'' together with the rules 
identified below comprise the submitted nonattainment area plan. The 
remaining portions are for informational purposes only.
    (A) Santa Barbara County APCD Rules 320, 321, 323, 327, 329 to 332, 
201.C and 205.C. (except subparagraph 5.b.8.).
    (B) Ventura County APCD Rules 26 (except 26.2, 26.3 and 26.4), 74.4, 
74.7, and 74.8.
    (78) Revised regulations for the following APCD submitted on 
November 19, 1979, by the Governor's designee.
    (i) South Coast AQMD.
    (A) Deletion of Rules 67 and 72.
    (ii) California Lead SIP.
    (79) Revised regulations for the following APCD's submitted on June 
2, 1980, by the Governor's designee.
    (i) Monterey Bay Unified APCD.
    (A) Rule 427.
    (ii) Bay Area AQMD.
    (A) New or amended Regulation 1, Rules 1-100 to 1-111, 1-114, 1-200 
to 1-205, 1-207 to 217, 1-219 to 1-232, 1-400 to 1-402, 1-410 to 1-412, 
1-420, 1-430 to 1-434, 1-440, 1-441, 1-500 to 1-502, 1-510, 1-521, 1-
530, 1-540, 1-541, 1-543, 1-544; Regulation 5, Rules 5-100, 5-101, 5-
110, 5-111, 5-200 to 5-207, 5-300, 5-301, 5-400 to 5-404; Regulation 6, 
Rules 6-100, 6-101, 6-200 to 6-204, 6-300 to 6-304, 6-310, 6-312,6-320, 
6-330, 6-400, 6-401, 6-500 to 6-502; Regulation 11, Rules 11-1-100 to 
11-1-102, 11-1-300 to 11-1-303; Regulation 12, Rules 12-2-100, 12-2-101, 
12-2-200, 12-2-201, 12-2-300, 12-2-301, 12-2-500, 12-2-501, 12-3-100, 
12-3-101, 12-3-300, 12-3-301, 12-3-500, 12-3-501-12-4-100 to 12-4-102, 
12-4-200 to 12-4-212, and 12-4-300 to 12-4-307.
    (B) New or amended Regulation 1: 1-206, 1-520, 1-542, and 1-600 to 
1-604; Regulation 6: 6-305, 6-311, 6-600, and 6-601; and Regulation 11: 
11-1-500, 11-1-501, and 11-1-600 to 11-1-603.
    (iii) Ventura County APCD.
    (A) New or amended Rule 2.
    (B) New or amended Rule 59.
    (iv) South Coast AQMD.
    (A) Deletion of Rule 471.
    (B) New Rule 466.1.
    (v) San Diego County APCD.
    (A) New or amended Rules 1, 2 (a), (b), (t), (v), (u), (x), and (y), 
14, 17, 67.0, and 67.1.
    (vi) Shasta County APCD.
    (A) New Rule 3.17.
    (80) The following amendments to the plan were submitted on August 
21, 1979 by the Governor's designee.
    (i) Revised regulations for Placer County APCD--Lake Tahoe Air Basin 
Portion.
    (A) New or amended Rules 101-104, 201-204, 206-211, 215, 217, 301-
308, and 310-319.
    (B) New Rule 507.

    Editorial Note: At 47 FR 27068, June 23, 1982, the following 
paragraph (c)(80)(i)(B) was added to Sec. 52.220.

    (B) New or amended Rules 212, 213, 508 (except Paragraph 
(1)(C)(3)(h), and 514.
    (C) New or amended Rules 502-506 and 511-513.
    (D) Previously approved and now deleted, Rule 104.
    (ii) Chapter 8, Lake Tahoe Basin Control Strategy, including Support 
Documents and Appendices. The Transportation Improvement Program and 
Regional Transportation Plan are for informational purposes only.
    (81) Revised regulations for the following APCD, submitted on 
February 11, 1980 by the Governor's designee.
    (i) El Dorado County APCD--Lake Tahoe Air Basin Portion.
    (A) New or amended Rules 507, 511-515, and 519-528.
    (B) New or amended Rules 501 to 506, 508 to 510, and 516 to 518.
    (82) [Reserved]
    (i) Ventura County APCD.
    (A) New or amended Rule 74.6.
    (83)(i)(A) [Reserved]
    (B) New Rules 22, 23, and 27.
    (C) New or amended Regulation 8: Rule 21.
    (ii) Kings County APCD.
    (A) New or amended Rule 414.
    (iii) [Reserved]
    (A) Rule 410.
    (B) New or amended Rules 411.1 and 416.1.
    (84) Revised regulations for the following APCDs submitted on 
October 10, 1980, by the Governor's designee.
    (i) Madera County APCD.
    (A) New or amended Rule 410.4.
    (ii) Merced County APCD.
    (A) New or amended Rule 409.4.

[[Page 124]]

    (iii) Kings County APCD.
    (A) New or amended Rule 410.4.
    (iv) San Joaquin County APCD.
    (A) New or amended Rule 409.4.
    (v) Stanislaus County APCD.
    (A) New or amended Rule 409.4.
    (vi) Tulare County APCD.
    (A) New or amended Rule 410.4.
    (vii) Modoc County APCD.
    (A) Amended Rule 3:12.
    (85) Revised regulations for the following APCDs submitted on 
December 15, 1980, by the Governor's designee.
    (i) Tulare County APCD.
    (A) New or amended Rule 412.
    (B) New or amended Rule 412.1.
    (C) New or amended Rules 201 and 417.1.
    (ii) Madera County APCD.
    (A) New or amended Rule 412.1
    (B) New or amended Rules 201, 202, 301, and 417.1.
    (iii) Sacramento County APCD.
    (A) New or amended Rule 13.
    (iv) San Diego County APCD.
    (A) New or amended Rules 61.0, 61.0 (n) and (o), 61.1, 61.1(a)(1) 
(i) and (h), 61.2, 61.2(a), 61.3 and 61.4
    (v) San Bernardino County APCD, Southeast Desert Air Basin portion.
    (A) New or amended Rules 461 and 462.
    (vi) Tehama County APCD.
    (A) New or amended Rules 1.2, 1.3, 2.7, 2.8, 2.9, 3.1, 3.2, 3.3-
3.14, 4.1, 4.2, 4.6, and 4.7.
    (B) Previously approved and now deleted Rule 2.8 (Further 
Information).
    (vii) Santa Barbara County APCD.
    (A) New or amended Rule 210.
    (viii) South Coast AQMD.
    (A) New Rule 1130.
    (ix) Kings County APCD.
    (A) New or amended Rule 417.1.
    (x) Kern County APCD.
    (A) New or Amended Rules 110 and 417.1.
    (86) Revised regulations for the following APCD's submitted on July 
10, 1980 by the Governor's designee.
    (i) Bay Area AQMD.
    (A) Regulation 8: Rule 2 (Paragraph 301).
    (B) New Rules 17 (paragraphs 112, 302, 400, and 401) and 26.
    (C) New or amended Regulations, Rules 1-206, 1-218, 6-311, 9-1-100, 
9-1-101, 9-1-110 9-1-200 to 9-1-204, 9-1-300 to 9-1-308, 9-1-310, 9-1-
311, 9-1-400 to 9-1-404, 9-1-500 to 9-1-502, and 9-4-302.
    (D) New or amended Rule 1-541 and Regulation 9, Rules 9-1-600 to 9-
1-605.
    (ii) Butte County APCD.
    (A) Amended Rule 4.9.
    (87) Revised regulations for the following APCD's submitted on 
September 5, 1980 by the Governor's designee.
    (i) Bay Area AQMD.
    (A) Regulation 8: Rule 5, Rule 6, and Rule 12.
    (B) New Rules 25 and 28 (except section 401).
    (ii) San Diego County APCD.
    (A) New or amended Rule 19.
    (iii) San Joaquin County APCD.
    (A) New or amended Rule 411.2.
    (B) New or amended Rules 202 and 416.1.
    (iv) San Bernardino County APCD, Southeast Desert Air Basin portion.
    (A) New or amended Rules 1301, 1302, 1303, 1304, 1305, 1306, 1307, 
1308, 1310, 1311, and 1313.
    (v) Los Angeles County APCD, Southeast Desert Air Basin portion.
    (A) New or amended Rules 1301, 1302, 1303, 1304, 1305, 1306, 1307, 
1308, 1310, 1311, and 1313.
    (vi) Sacramento County APCD.
    (A) New or amended Rules 74, 90, 92, 93, 94, 95, 96, 98, and 
Regulation VII.
    (B) Previously approved on June 18, 1982 and now deleted without 
replacement Rule 74.
    (vii) Ventura County APCD.
    (A) New or amended Rules 2 and 55.
    (viii) Shasta County APCD.
    (A) New Rule 2:6.
    (88) Revised regulations for the following APCDs submitted on July 
25, 1980, by the Governor's designee.
    (i) Stanislaus County APCD.
    (A) New or amended Rule 209.1 (except paragraphs (3)(E) and 
(5)(B)(8)).
    (B) New or amended Rules 103 and 305.
    (C) New or amended Rules 202 and 416.1.
    (D) Previously approved on December 9, 1981 and now deleted without 
replacement Rule 305.
    (ii) Bay Area AQMD.
    (A) New or amended Regulation 3, Rules 3-100 to 3-103, 3-200 to 3-
206, 3-208 to 3-211, 3-300 to 3-311, and 3-400 to 3-408.
    (iii) South Coast AQMD.
    (A) New or amended Rule 1119.
    (B) Amended Rule 462.

[[Page 125]]

    (iv) [Reserved]
    (v) Merced County APCD.
    (A) New or amended Rule 411.1.
    (B) New or amended Rules 202 and 416.1.
    (89) Revised regulations for the following APCDs submitted on March 
30, 1981, by the Governor's designee.
    (i) Kings County APCD.
    (A) New or amended Rule 411.
    (ii) Yolo-Solano County APCD.
    (A) New or amended Rule 2.13(h)(6).
    (iii) Yuba County APCD.
    (A) Amended Rules 3.8, 3.12, and 3.15.
    (iv) Imperial County APCD.
    (A) New Rule 418.1.
    (v) Monterey Bay Unified APCD.
    (A) New Rule 425.
    (vi) Lake County APCD.
    (A) New or amended Sections 101, 227.4, 301, 1602, and Table VI.
    (B) Previously approved on April 13, 1982 and now deleted without 
replacement Rule 301 and Table VI.
    (vii) South Coast AQMD.
    (A) Amended Rule 1102.1.
    (90) The following amendments to the plan were submitted on December 
31, 1979, by the Governor's designee.
    (i) Chapter 22--Air Quality Monitoring by State and Local Air 
Monitoring Stations (SLAMS).
    (91) The following amendments to the plan were submitted on November 
13, 1979, by the Governor's designee.
    (i) The Sacramento Valley Air Basin Control Strategy (Chapter 13 of 
the Comprehensive Revisions to the State of California Implementation 
Plan for the Attainment and Maintenance of Ambient Air Quality 
Standards): those portions pertaining to the Sacramento Metropolitan 
Area including the following rules:
    (A) Placer County APCD (Mountain Counties Air Basin portion) Rules 
212, 217, and 218.
    (B) Sacramento County APCD Rules 6, 11, 12, 16, 19, and 56 (except 
paragraph (5)(a)(8)).
    (C) Yolo-Solano County APCD Rules 2.14 and 3.4 [except paragraph 
(5)(a)(8)].
    (ii) The Sacramento Valley Air Basin Control Strategy [Chapter 13 of 
the Comprehensive Revisions to the State of California Implementation 
Plan for the Attainment and Maintenance of Ambient Air Quality 
Standards]: those portions pertaining to Butte, Yuba, and Sutter 
Counties, including the following rules:
    (A) Butte County APCD Rules 2.12f and 4-5.
    (92) Revised regulations for the following APCDs submitted on May 
28, 1981, by the Governor's designee.
    (i) Stanislaus County APCD.
    (A) New or amended Rule 409.5.
    (ii) Placer County (Mountain Counties Air Basin portion).
    (A) New or amended Rules 213, 216, and 223.
    (B) New or amended Rules 102, 203, 211, 301, 305, 306, 324, 325, 
601, and 702.
    (C) Rule 214.
    (D) Previously approved and now deleted without replacement Rules 
601 and 702.
    (iii) Lake County APCD.
    (A) New Rule 216.1.
    (iv) Great Basin Unified APCD.
    (A) New or amended Rules 101, 300, 404-A, 423, and 424.
    (v) San Diego County APCD.
    (A) New or amended Rules 127, 130, 131, 132, and 134.
    (B) New or amended Rule 21.
    (vi) South Coast AQMD.
    (A) New or amended Rule 1113.
    (93) Revised regulations for the following APCDs submitted on June 
22, 1981, by the Governor's designee.
    (i) Stanislaus County APCD.
    (A) New or amended Rule 409.3.
    (B) New or amended Rule 409.8.
    (ii)(A) [Reserved]
    (B) New Rule 28, Section 401.
    (C) New or amended Regulation 5, Rule 5-401.3.
    (iii) Plumas County APCD.
    (A) New or amended Rules 203, 301-319, 512-516, 703, and 710.
    (B) New or amended Rules 501-511 and 517-521.
    (iv) Sierra County APCD.
    (A) New or amended Rules 203, 301-319, 512-516, 522, 523, 703, and 
710.
    (B) New or amended Rules 501-511 and 517-521.
    (C) Previously approved on April 23, 1982 and now deleted without 
replacement Rule 522.
    (v) Kern County APCD.
    (A) New or amended Rule 410.6.
    (vi) El Dorado County APCD (Mountain Counties Air Basin Portion).
    (A) Rules 318, 319, and 320.

[[Page 126]]

    (94) Revised regulations for the following APCD's submitted on 
October 7, 1980, by the Governor's designee.
    (i) Stanislaus County APCD.
    (A) New or amended Rule 411.1.
    (ii) [Reserved]
    (iii) San Bernardino County APCD.
    (A) New or amended Rules 701, 704, 705, 707-711, and 712. Previously 
approved Rule 707, ``Plans'', submitted on June 6, 1977 is retained.
    (95) Revised regulations for the following APCD's submitted on March 
23, 1981, by the Governor's designee.
    (i) Kern County APCD.
    (A) New or amended Rule 412.1(a).
    (B) Amended Rule 412.1.
    (C) New or amended Rules 202, 202.1, and 426.
    (ii) Ventura County APCD.
    (A) Amended Rule 26.2.
    (B) New or amended Rules 21, 29, 30, and 64.
    (iii) Northern Sonoma County APCD.
    (A) Amended Regulation 2, Rules 100, 120, 140, 200, 220, 240, 300, 
and 320.
    (iv) South Coast AQMD.
    (A) Amended Rule 461.
    (v) Stanislaus County APCD.
    (A) New Rule 409.7.
    (B) New or amended Rule 301.
    (C) Previously approved on June 18, 1982 and now deleted without 
replacement Rule 301.
    (vi) Humboldt County APCD.
    (A) New or amended Rules 130, 200, 210, 220, 230, 240, 250, and 260.
    (96) Revised regulations for the following APCDs submitted on 
November 3, 1980, by the Governor's designee.
    (i) South Coast AQMD.
    (A) New or amended Rule 1113.
    (ii) Butte County APCD.
    (A) New or amended Rules 1-8, 1-8.1, 1-10, 1-13, 1-14, 3-1, 3-2, 3-
6, 3-11, 3-11.2, 3-11.3, 3-12, 3-12.1, 3-12.2, 3-14, 3-15, 3-16, and 3-
16.1.
    (iii) Glenn County APCD.
    (A) New or amended Rules 2 (a,i,v, and aa), 3, 11, 11.1, 11.2, 13, 
13.1, 14, 14.1, 14.2, 14.3, 15, 16, 19, 21, 21.1, 22, 75, 81, 83, 83.1, 
83.2, 96, 110, and 112.
    (B) Previously approved on January 26, 1982 and now deleted without 
replacement Rules 110 and 112.
    (iv) Yolo-Solano APCD.
    (A) New or amended Rules 1.2 (a and g), 6.1 and 6.3.
    (v) Bay Area AQMD.
    (A) New Rule 20.
    (97) Revised regulations for the following APCDs submitted on June 
24, 1980, by the Governor's designee.
    (i) Sacramento County APCD.
    (A) New or amended Rule 18.
    (98) Revised regulations for the following APCDs, submitted on 
January 28, 1981, by the Governor's designee.
    (i) Sutter County APCD.
    (A) Amended Rules 3.8, 3.14, and 3.15.
    (B) New or amended Rules 1.0-1.3, 2.1-2.12, 2.15, 2.16, 3.0-3.7, 
3.9, 3.10, 3.12, 3.13, 4.0-4.5, 4.7-4.10, 4.12-4.15, 5.0-5.19, 6.0-6.7, 
7.0, 7.1, 7.2, 8.0, 8.1, 8.2, 9.0-9.7, and 9.8.
    (C) Previously approved and now deleted Rules 2.1 (Control of 
Emissions), 2.7 (Wet Plumes), 2.15 (Fuel Burning Equipment), 2.20 
(Payment of Order Charging Costs), 3.7 (Information), 4.5 (Standards for 
Granting Applications), 4.6 (Permits, Daily Limits, and 4.8 (Permit 
Forms).
    (D) Previously approved on April 12, 1982 and now deleted without 
replacement Rules 5.0 to 5.17, 5.19, 6.0 to 6.7, and 7.0 to 7.2.
    (ii) Siskiyou County APCD.
    (A) New or amended agricultural burning regulations consisting of 
``General Provisions'' and Articles I-VII.
    (iii) Mendocino County APCD.
    (A) Amended Regulation 2, Rules 100, 120, 140, 200, 220, 240, 300, 
320, Appendices A, B, and C.
    (iv) Del Norte County APCD.
    (A) Amended Regulation 2, Rules 100, 120, 140, 200, 220, 240, 300, 
320, Appendices A, B, and C.
    (v) Humboldt County APCD.
    (A) Amended Regulation 2, Rules 100, 120, 140, 200, 220, 240, 300, 
320, Appendices A, B, and C.
    (vi) Trinity County APCD.
    (A) Amended Regulation 2, Rules 100, 120, 140, 200, 220, 240, 300, 
320, Appendices A, B, and C.
    (vii) El Dorado County APCD.
    (A) New Rule 313.
    (B) Rules 313, 314, 315, 316, and 317.
    (viii) Ventura County APCD.
    (A) New Rule 71.2.
    (ix) Bay Area AQMD.
    (A) New or amended Rules 1-112, 1-113, 1-115 and Regulation 9, Rule 
9-3-202.
    (x) South Coast AQMD.
    (A) New or amended Rule 1115.

[[Page 127]]

    (xi) San Diego County APCD.
    (99) Commitments by the Bay Area AQMD, Fresno County APCD, Kern 
County APCD, Monterey Bay Unified APCD, Sacramento County APCD, San 
Diego County APCD, Santa Barbara County APCD, South Coast AQMD, and 
Ventura County APCD to carry out public notification programs as 
required by section 127 of the Clean Air Act and in accordance with EPA 
guidance. These commitments were submitted by the Air Resources Board on 
January 22, 1981.
    (100) Revised regulations for the following APCDs submitted on 
October 25, 1979, by the Governor's designee.
    (i) San Diego County APCD.
    (A) New or amended Rules 67.3 and 67.5.
    (101) Revised regulations for the following APCD's submitted on July 
30, 1981 by the Governor's designee.
    (i) Bay Area AQMD.
    (A) Regulation 8, Rule 1 (Paragraph 202) and Rule 16 (paragraph 
110).
    (B) New or amended Regulation 2, Rule 2-2-114; Regulation 5, Rule 5-
401.13; and Manual of Procedures--Volume I to Volume VI.
    (C) New or amended Regulation 8, Rule 24.
    (ii) Kern County APCD.
    (A) New or amended Rules 603, 609, 610, 611, and 613.
    (B) New or amended Rules 108, 201, 301, 302, and 305.
    (C) New or amended Rules 414 and 410.3.
    (D) New or amended Rules 410.7, 412, and 414.4.
    (E) Previously approved on July 6, 1982 and now deleted without 
replacement Rule 305 (including Southeast Desert).
    (102) Revised rules for the following APCDs submitted on July 14, 
1981 by the Governor's designee.
    (i) San Joaquin County.
    (A) New Rules 409.5 and 409.6.
    (ii) Stanislaus County.
    (A) New Rule 409.6.
    (B) New or amended Rules 409.7 and 409.8.
    (iii) Merced County APCD.
    (A) New or amended Rules 409.6.
    (iv) South Coast AQMD.
    (A) New or amended Rule 301.
    (103) Revised rules for the following APCDs, submitted on October 
23, 1981 by the Governor's designee.
    (i) Kings County.
    (A) Amended Rule 412.2.
    (ii) San Diego County APCD.
    (A) New or amended Rule 67.4 and 67.6.
    (B) New or amended Rules 42, 64, 101-103, and 109.
    (C) New Rule 67.8.
    (D) Previously approved on July 6, 1982 and now deleted without 
replacement Rule 42.
    (iii) Santa Barbara County APCD.
    (A) Rule 325.
    (B) New or amended Rules 601-608 and 609.
    (C) Previously approved and now deleted Rules 609 (Scientific 
Committee) and 610 (Emergency Action Committee).
    (iv) Ventura County APCD.
    (A) Amended Rule 70(E).
    (B) New or amended Rules 2, 12, 16, 23, 41, 42, and 74.2.
    (C) New Rule 74.5.
    (D) Amended Rule 74.9.
    (E) Previously approved on June 18, 1982 and now deleted without 
replacement Rule 42.
    (v) Sacramento County APCD.
    (A) Amended Rule 20.
    (B) New or amended Rules 50, 70, and 14.
    (C) New Rules 4A, 4B, 10 and 51.
    (vi) Del Norte County APCD.
    (A) Amended Rules 300 and 310.
    (B) Previously approved on April 13, 1982 and now deleted without 
replacement Rules 300 and 310.
    (vii) Humboldt County APCD.
    (A) Amended Rules 300 and 310.
    (B) Previously approved on April 13, 1982 and now deleted without 
replacement Rules 300 and 310.
    (viii) Mendocino County APCD.
    (A) Amended Rules 300 and 310.
    (B) Previously approved on April 13, 1982 and now deleted without 
replacement Rules 300 and 310.
    (ix) Northern Sonoma County APCD.
    (A) Amended Rules 300 and 310.
    (B) Previously approved on April 13, 1982 and now deleted without 
replacement Rules 300 and 310.
    (x) Trinity County APCD.
    (A) Amended Rules 300 and 310.

[[Page 128]]

    (B) Previously approved on April 13, 1982 and now deleted without 
replacement Rules 300 and 310.
    (xi) Great Basin Unified APCD.
    (A) Amended Rule 301.
    (xii) San Luis Obispo County APCD.
    (A) New or amended Rules 301, 302, and 411.
    (B) Previously approved on June 18, 1982 and now deleted without 
replacement Rule 301.
    (C) Previously approved on June 18, 1982 and now deleted without 
replacement Rule 301.
    (xiii) El Dorado County APCD (Mountain Counties Air Basin).
    (A) New or amended Rules 301-319, 501, 703, and 710.
    (xiv) Imperial County APCD.
    (A) New or amended Rules 101, 301, 302, 305-307.
    (B) Previously approved on May 27, 1982 and now deleted without 
replacement Rule 305.
    (xv) Shasta County APCD.
    (A) Amended Rule 2:11.
    (xvi) Monterey Bay Unified APCD.
    (A) Amended Rules 301, 601, and 602.
    (xvii) Tuolumne County APCD.
    (A) New or amended Rules 203, 301-319, 501-521, 703, and 710.
    (B) Previously approved on May 27, 1982 and now deleted without 
replacement Rule 516.
    (xviii) South Coast AQMD.
    (A) New or amended Rules 504.1, 218, 219, 220, 409, and 502.
    (B) Previously approved on July 6, 1982 and now deleted without 
replacement Rule 504.1.
    (104) Revised regulations for the following APCD's submitted on 
November 5, 1981 by the Governor's designee.
    (i) Bay Area AQMD.
    (A) Regulation 2, Rule 1: 2-1-101, 2-1-102, 2-1-111, 2-1-112, 2-1-
201 to 2-1-205, 2-1-301 to 2-1-306, 2-1-401 to 2-1-410, and 2-1-420 to 
2-1-423; Rule 2: 2-2-101 to 2-2-114, 2-2-201 to 2-2-208, 2-2-301 to 2-2-
306, 2-2-310, and 2-2-401 to 2-2-410.
    (ii) South Coast AQMD.
    (A) New or amended Rule 444.
    (iii) Fresno County APCD.
    (A) New or amended Rule 409.6.
    (105) Schedule to study Nontraditional Total Suspended Particulate 
Sources and commitment to implement control measures necessary to 
provide for attainment, submitted on November 18, 1981 by the Governor's 
designee.
    (106) The Southeast Desert Air Basin Control Strategy for ozone 
(Chapter 19 of the Comprehensive Revisions to the State of California 
Implementation Plan for the Attainment and Maintenance of the Ambient 
Air Quality Standards) was submitted by the Governor's designee on 
February 15, 1980. The portions of the Southeast Desert Air Basin 
Control Strategy identified in Table 19-1 (Summary of Plan Compliance 
with Clean Air Act Requirements), except those which pertain to Imperial 
County, comprise the plan. The remaining portions are for informational 
purposes only.
    (107) On August 11, 1980, the Governor's designee submitted a 
revision to the State Implementation Plan which adds the Southeast 
Desert Air Basin portion of Riverside County into the South Coast Air 
Quality Management District.
    (108) On November 28, 1980, the Governor's designee submitted a 
revision to the State Implementation Plan which deletes Rule 67, for the 
San Bernardino County APCD as applied to new sources.
    (109) Three items submitted for Fresno County and the Sacramento 
Metropolitan Area by the Governor's designee on October 9, 1980:
    (i) Air Quality Planning Addendum-Council of Fresno County 
Governments 1979-84 Overall Work Program.
    (ii) Emission Inventory, 1976 for the Sacramento Metropolitan Area.
    (iii) Air Quality Plan Technical Appendix, January 1979 for the 
Sacramento Metropolitan Area.
    (110) Five items submitted for Ventura County by the Governor's 
designee on April 1, 1980:
    (i) Appendix B-81, Empirical Kinetic Modeling Approach: Ozone 
Formation, Transport, and Concentration Relationships in Ventura County; 
Update of Emission Reduction Required for Attainment of Ozone NAAQS.
    (ii) Letter: Jan Bush to Mike Redemer, January 23, 1981.
    (iii) Letter and enclosures: Janet Lyders to Mike Scheible, February 
6, 1981.
    (iv) Letter and enclosures: Jan Bush to William Lockett, December 
15, 1980.

[[Page 129]]

    (v) Letter and enclosures: Jan Bush to William Lockett, October 23, 
1980.
    (111) Four items submitted for Ventura County by the Governor's 
designee on July 16, 1981:
    (i) Attachment V--Transportation Control Measures.
    (ii) Ventura Air Quality Management Plan, Appendix O, Plan for 
Attainment of Standards for Total Suspended Particulates In Ventura 
County: Interim Report, July, 1980.
    (iii) Attachment IV--Population Forecasts.
    (iv) Attachment VI--Implementation of Emission Reductions Required 
for Attainment of TSP Standards.
    (112) Plan for Attainment of the Federal Secondary Total Suspended 
Particulate Standard in Santa Clara County, an addendum to the San 
Francisco Bay Area Air Basin Control Strategy (Chapter 15) submitted on 
March 16, 1981, by the Governor's designee.
    (113) Supplemental material for the San Diego Nonattainment Area 
Plan submitted on July 13, 1981, by the Governor's designee.
    (114) Supplemental material for the San Diego Nonattainment Area 
Plan submitted on August 31, 1981, by the Governor's designee.
    (115) Supplemental material for the San Diego Nonattainment Area 
Plan submitted on December 8, 1981, by the Governor's designee.
    (116) Supplemental material for the South Coast Nonattainment Area 
Plan submitted on July 24, 1981, by the Governor's designee.
    (117) Supplemental material for the South Coast Nonattainment Area 
Plan submitted on December 24, 1981, by the Governor's designee.
    (118) Supplemental material for the South Coast Nonattainment Area 
Plan submitted on February 18, 1982, by the Governor's designee.
    (119) Revised regulations for the following APCDs submitted on April 
17, 1980, by the Governor's designee.
    (i) El Dorado County APCD (Mountain Counties Air Basin).
    (A) New or amended Rules 502-520.
    (B) Rule 102.
    (ii) Mendocino County APCD.
    (A) New or amended Rules 130, 200, 210, 220, 230, 240, 250, and 260.
    (120) The Mountain Counties Air Basin Control Strategy for ozone 
(Chapter 9 of the ``Comprehensive Revisions to the State of California 
Implementation Plan for the Attainment and Maintenance of the Ambient 
Air Quality Standards'' was submitted by the Governor's designee on 
April 3, 1981. The submittal also included revised regulations for the 
following APCD's.
    (i) El Dorado County APCD (Mountain Counties Air Basin portion).
    (A) Rules 401, 402, 403, 404, 405, 406, 407, 410, 411, 415, 416, 
418, 419, 420, 421, 422, 423, 424, and 425.
    (121) Revised regulations for the following APCDs submitted on March 
1, 1982 by the Governor's designee.
    (i) South Coast AQMD.
    (A) New or amended Rule 474.
    (B) Amended Rules 107, 1107, 1108.1, 1125 and 1126.
    (C) Amended Rule 1110.
    (ii) San Diego County APCD.
    (A) New or amended Rules 62 and 53.
    (B) Amended Rule 67.6(e).
    (C) Amended Rule 17, adopted on November 25, 1981.
    (iii) Lake County APCD.
    (A) New or amended Rule 655.
    (iv) Bay Area AQMD.
    (A) Amended Regulation 8, Rules 2-112 and 5-313.4.
    (v) Ventura County APCD.
    (A) Amended Rule 74.6.
    (122) [Reserved]
    (123) Supplemental material for the Kern County Nonattainment Area 
Plan submitted on March 4, 1982, by the Governor's designee.
    (124) Revised regulations for the following APCDs submitted on 
August 6, 1982, by the Governor's designee.
    (i) Bay Area AQMD.
    (A) New or amended Regulation 1: Rules 1-100, 1-112, 1-205, 1-233, 
1-234, 1-235, 1-520, 1-522, 1-530, 1-540, 1-543, 1-544, and 1-602; 
Regulations 4: Rule 4-303; Regulation 5: Rules 5-208 and 5-402; and 
deletion of Regulation 6: Rule 6-132.
    (B) [Reserved]
    (C) Amended Regulation 8, Rules 2, 4, 5, 8 and 10.
    (D) New or amended Regulation 2: Rules 2-1-207, 2-1-208, 2-1-301, 2-
1-304, and 2-1-307.
    (E) Amended Regulation 8, Rule 23.
    (ii) Lake County APCD.

[[Page 130]]

    (A) New or amended Rules 630, 631, 660.1, 660.2, and 660.3.
    (iii) San Joaquin County APCD.
    (A) New or amended Rules 203, 415, 503, and 521.
    (B) Previously approved on November 10, 1982 and now deleted without 
replacement Rules 503 and 521.
    (iv) South Coast AQMD.
    (A) New or amended Rule 407.
    (B) Amended Rule 1107.
    (C) [Reserved]
    (v) Stanislaus County APCD.
    (A) New or amended Rules 203 and 503.
    (B) New or amended Rules 409.4 and 409.8.
    (C) Previously approved on November 10, 1982 and now deleted without 
replacement Rule 503.
    (vi) Del Norte County APCD.
    (A) New or amended Rules 616, 618, and 620.
    (B) New or amended Rule 230, adopted December 14, 1981.
    (C) Previously approved on Novmber 10, 1982 and now deleted without 
replacement Rules 616 and 618.
    (vii) Humboldt County APCD.
    (A) New or amended Rules 616, 618, and 620.
    (B) New or amended Rule 230, adopted December 8, 1981.
    (C) Previously approved on November 10, 1982 and now deleted without 
replacement Rules 616 and 618.
    (viii) Mendocino County APCD.
    (A) New or amended Rules 610, 616, 618, and 620.
    (B) New or amended Rules 130 (introductory text, b1, m1, p5, and 
s2), and 230, adopted January 5, 1982.
    (C) Previously approved on November 10, 1982 and now deleted without 
replacement Rules 616 and 618.
    (ix) Northern Sonoma County APCD.
    (A) New or amended Rules 616, 618, and 620.
    (B) New or amended Rules 130 (introductory text, b1, n1, p5, and 
s2), 220(c), 230, and 260, adopted February 23, 1982 and rule 200, 
adopted June 15, 1982.
    (C) Previously approved on November 10, 1982 and now deleted without 
replacement Rules 616 and 618.
    (x) Trinity County APCD.
    (A) New or amended Rules 616, 618, and 620.
    (B) New or amended Rule 230, adopted December 7, 1981.
    (C) Previously approved on November 10, 1982 and now deleted without 
replacement Rules 616 and 618.
    (xi) Kern County APCD.
    (A) New or amended Rule 411.
    (xii) Butte County APCD.
    (A) New or amended Rules 4-6 and 4-6A.
    (125) Revised Regulations for the following APCDs submitted on May 
20, 1982 by the Governor's designee.
    (i) San Diego County APCD.
    (A) New or amended Rule 40.
    (ii) South Coast AQMD.
    (A) New or amended Rule 431.1.
    (B) New or amended Rules 303 and 304.
    (C) [Reserved]
    (D) Amended Rules 442, 467 and 1128.
    (iii) Monterey Bay Unified APCD.
    (A) New or amended Rule 422.
    (B) New Rule 428.
    (iv) Shasta County APCD.
    (A) New or amended Rules 2:6, 2:7, 2:8, 2:9, 2:11 and 4:4.
    (B) Previously approved on November 10, 1982 and now deleted without 
replacement Rule 4.4.
    (v) Tulare County APCD.
    (A) New or amended Rules 104 and 405.
    (B) Amended Rule 410.1.
    (vi) Yolo-Solano APCD.
    (A) New or amended Rules 4.1 and 4.2.
    (B) Previously approved on November 10, 1982 and now deleted without 
replacement Rules 4.1 and 4.2.
    (vii) Yuba County APCD.
    (A) New or amended Rule 9.6.
    (viii) Bay Area AQMD.
    (A) Manual of Procedures: Volumes I, V and VI.
    (B) Amended Regulation 8, Rules 7, 14, 18 and 19.
    (ix) San Joaquin County APCD.
    (A) Amended Rule 412.
    (126) Revised regulations for the following APCDs submitted on 
November 8, 1982 by the Governor's designee.
    (i) Sacramento County APCD.
    (A) New or amended Rules 59 and 70.
    (B) Amended Rules 16 and 19.
    (C) Previously approved on June 1, 1983 and now deleted without 
replacement Rule 70.
    (ii) Santa Barbara County APCD.
    (A) New or amended Rule 210D.

[[Page 131]]

    (iii) Stanislaus County APCD.
    (A) New or amended Rules 110, 202, and 302.
    (B) Amended Rules 409.8, 411 and 411.1(G).
    (C) Previously approved on June 18, 1982 and now deleted without 
replacement Rule 302.
    (iv) South Coast AQMD.
    (A) New or amended Rules 708.3 and 1105.
    (v) Tulare County APCD.
    (A) New or amended Rule 519.
    (B) Amended Rules 410.3 and 410.4.
    (C) Previously approved on June 1, 1983 and now deleted without 
replacement Rule 519.
    (vi) Yolo-Solano County APCD.
    (A) New or amended Rule 6.1.
    (B) Amended Rule 2.22.
    (127) Revised regulations for the following APCDs submitted on 
February 3, 1983 by the Governor's designee.
    (i)(A) [Reserved]
    (B) Amended Regulation 3: Rules 3-102, 3-302, 3-302.1, 3-303, and 
Schedule A.
    (C) Amended Rules 13 and 29.
    (D) New or amended Regulation 2: Rules 2-2-113.2, 2-2-115, 2-2-209, 
2-2-210, 2-2-211, 2-2-303.2, 2-2-304.1, 2-2-304.2, and 2-2-404; and 
Regulation 3: Rule 3-312.
    (ii) Fresno County APCD.
    (A) Amended Rules 406 and 408.
    (B) Amended Rule 409.1.
    (iii) North Coast Unified AQMD.
    (A) New Rule 350.
    (B) Previously approved on November 18, 1983 and now deleted without 
replacement Rule 350.
    (iv) Imperial County APCD.
    (A) Amended Rule 409.
    (B) Amended Rule 424.
    (v) Monterey Bay Unified APCD.
    (A) New or amended Rule 601.
    (B) Amended Rule 301, submitted on February 3, 1983.
    (vi) San Luis Obispo County APCD.
    (A) Amended Rule 302.
    (B) Previously approved on November 18, 1983 and now deleted without 
replacement Rule 302.
    (vii) South Coast AQMD.
    (A) New or amended Rules 301.1, 302, 303, and Resolutions 82-23 and 
82.35.
    (B) New or amended Rules 461, 1102, and 1102.1.
    (C) New or amended Rules 301, 304, 401(b) and 1148.
    (D) Previously approved on November 18, 1983 and now deleted without 
replacement Rule 303.
    (viii) Ventura County APCD.
    (A) New or amended Rule 41.
    (B) Amended Rule 74.2.
    (128) The 1982 Ozone Air Quality Plan for the Monterey Bay Region 
was submitted on December 31, 1982 and January 14, 1983 by the 
Governor's designee.
    (129) The 1982 Ozone Air Quality Plan for Stanislaus County and the 
1982 Ozone and CO plan for San Joaquin County were submitted on December 
1, 1982 by the Governor's designee.
    (130) The 1982 Ozone Air Quality Plan for Santa Barbara County was 
submitted on December 31, 1982 by the Governor's designee.
    (131) [Reserved]
    (132) Revised regulations for the following APCDs submitted on June 
28, 1982, by the Governor's designee.
    (i) Kern County APCD.
    (A) Amended Rule 425.
    (133) The enabling legislation, Chapter 892, Statutes of 1982, 
(Senate Bill No. 33) for a California motor vehicle inspection and 
maintenance program and the California Air Resources Board's Executive 
Order G-125-15 submitted on September 17, 1982 by the Governor's 
designee.
    (134) A schedule to implement the California motor vehicle 
inspection and maintenance (I/M) program, the California Air Resources 
Board's Executive Order G-125-33, and local resolutions and requests 
from the Bay Area Air Quality Management District, Sacramento County 
APCD, Placer County APCD, Yolo-Solano APCD, San Diego County APCD, South 
Coast Air Quality Management District and Ventura County APCD to have 
the State implement the I/M program, submitted on July 26, 1983 by the 
Governor's designee.
    (135) The 1982 Ozone and CO Air Quality Plan for the San Francisco 
Bay Air Basin was submitted on February 4, 1983 by the Governor's 
designee.
    (136) The 1982 Ozone and CO Air Quality Plan for the San Diego Air 
Basin was submitted on February 28 and August 12, 1983 by the Governor's 
designee.

[[Page 132]]

    (137) Revised regulations for the following APCDs was submitted on 
July 19, 1983 by the Governor's designee.
    (i) Kern County APCD.
    (A) New or amended Rules 301.1 and 302.
    (B) Amended Rule 410.1
    (ii) Merced County APCD.
    (A) New or amended Rules 104, 108, 113, 202, 209.1, 301, 305, 407 
and 519.
    (B) Amended Rule 409.1.
    (C) New or amended Rules 409.4, 409.5, 411 and 411.1.
    (D) Previously approved on February 1, 1984 and now deleted without 
replacement Rules 305 and 319.
    (iii) Sacramento County APCD.
    (A) New or amended Rule 7.
    (B) Amended Rule 17.
    (iv) San Diego County APCD.
    (A) New or amended Rules 10 and 40.
    (B) Amended Rules 67.3, 67.4 and 67.6.
    (C) Previously approved on February 1, 1984 and now deleted without 
replacement Rule 40.
    (v) San Luis Obispo County APCD.
    (A) New or amended Rule 212.
    (vi) Shasta County APCD.
    (A) New or amended Rules 2.18, 3.4, and 3.15.
    (B) Amended Rules 3.3(b), 3.4(d) and 3.15(c).
    (vii) South Coast AQMD.
    (A) New or amended Rules 502, 1207 and deletion of 301.1.
    (B) New or amended Rules 301, 301.1, 301.2 and 431.1.
    (C) Previously approved on February 1, 1984 and now deleted without 
replacement Rule 502.
    (viii) Ventura County APCD.
    (A) Amended Rule 41.
    (B) Previously approved on February 1, 1984 and now deleted without 
replacement Rule 41.
    (ix) Monterey Bay Unified APCD.
    (A) Amended Rule 426.
    (x) Placer County APCD (Mountain Counties Air Basin portion).
    (A) Amended Rule 218.
    (xi) Fresno County APCD.
    (A) Amended Rule 409.4.
    (138) Revised regulations for the following APCDs was submitted on 
April 11, 1983 by the Governor's designee.
    (i) Butte County APCD.
    (A) Amended Rules 1-36, 4-2, 4-3, 4-11, and 5-3.
    (ii) El Dorado County APCD.
    (A) New or amended Rules 203, 206, 207, 209-212, 221-226, 521, 609-
612 and 700-703.
    (B) Amended Rules 214-220.
    (C) New Rule 213.
    (iii) Fresno County APCD.
    (A) New or amended Rule 301.
    (iv) Lake County APCD.
    (A) New or amended Rules 900 and 902.
    (v) Madera County APCD.
    (A) New or amended Rules 103-117, 301-305, 401-405, 421-425, 501-
503, 519, 606, 610 and 611.
    (B) Amended Rules 409, 410, and 417-419.
    (C) New or amended Rules 406, 407, 408, 411 and 420.
    (D) Previously approved on November 18, 1983 and now deleted without 
replacement Rules 305 and 502 to 503.
    (vi) Monterey Bay Unified APCD.
    (A) New or amended Rules 200, 201(p), 501, 503, 506, 507 and 508.
    (B) Amended Rule 425.
    (vii) Ventura County APCD.
    (A) New or amended Rule 59c.
    (viii) Kern County APCD.
    (A) Amended Rule 414.1.
    (ix) Kings County APCD.
    (A) Amended Rule 410.1.
    (139) Amendments to ``Chapter 27--California Lead Control Strategy'' 
was submitted on April 8, 1983 by the Governor's designee.
    (140) Revised regulations for the following APCDs were submitted on 
August 30, 1983 by the Governor's designee.
    (i) Bay Area AQMD.
    (A) Amended Regulation 3: Rules 3-100 through 3-103, 3-200 through 
3-211, 3-300 through 3-313 and 3-400 through 3-409.
    (B) New Regulation 8, Rule 30.
    (C) Previously approved on May 3, 1984 and now deleted without 
replacement Rule 3-301.
    (ii) Kern County APCD.
    (A) New or amended Rules 405, 408, 409, and 424.
    (iii) Stanislaus County APCD.
    (A) New or amended Rules 109 and 213.
    (B) Amended Rule 409.1.
    (iv) Yolo-Solano APCD.
    (A) Amended Rule 2.13(1).

[[Page 133]]

    (141) The 1982 CO Air Quality Plan for the Lake Tahoe Air Basin was 
submitted on December 20, 1982 by the Governor's designee.
    (142) The 1982 ozone and CO Air Quality Plan for the Sacramento 
nonattainment area submitted on January 10, 1984 by the Governor's 
designee, except for the attainment and RFP demonstration portions of 
the ozone plan.
    (143) Revisions to the 1982 ozone and CO Air Quality Plan for the 
Sacramento nonattainment area submitted on February 10, 1984.
    (144) The 1982 Ozone and CO Air Quality Management Plan for the 
South Coast Air Basin submitted on December 31, 1982 and subsequently 
amended on February 15, and June 28, 1984 by the Governor's designee, 
except for:
    (i) The attainment and RFP demonstration portions of the plan.
    (ii) The emission reduction credit for the New Source Review control 
measure.
    (145) The 1982 Ozone Air Quality Management Plan for Ventura County 
submitted on December 31, 1982 by the Governor's designee except for the 
attainment and RFP demonstration portions of the plan.
    (146) The 1982 Ozone and CO Clean Air Plan for the Fresno 
nonattainment area submitted on December 1, 1982 by the Governor's 
designee, except for the attainment and RFP demonstration portions of 
the plans.
    (147) [Reserved]
    (148) Revised regulations for the following APCDs were submitted on 
October 27, 1983 by the Governor's designee.
    (i) Bay Area AQMD.
    (A) New or amended Regulations 6-303.4, 9-1-100, 9-1-101, 9-1-110, 
9-1-200 through 9-1-205, 9-1-300 through 9-1-312, 9-1-400 through 9-1-
404, 9-1-500 through 9-1-503, 9-1-600 through 9-1-605 and 5-401.13.
    (B) Amended Regulation 8, Rules 3, 9, 10, 20, 22, 25 and 28.
    (ii) El Dorado County APCD.
    (A) New or amended Rules 102, 226, 227, and 228.
    (B) New Rules 224 and 225.
    (iii) Monterey Bay Unified APCD.
    (A) New or amended Rules 407, 410, and 411.
    (iv) San Diego County APCD.
    (A) New or amended Rule 68.
    (B) New Rule 67.9.
    (v) Shasta County APCD.
    (A) New or amended Rule 2.6.
    (vi) South Coast AQMD.
    (A) New or amended Rules 1105 and 1111.
    (B) New or amended Rules 1113, 1122, 1136, 1141 and 1145.
    (vii) Ventura County APCD.
    (A) New or amended Rule 30.
    (viii) Madera County APCD.
    (A) Amended Rule 416.
    (149) Revised regulations for the following APCD's submitted on 
January 20, 1983 by the Governor's designee.
    (i) California State.
    (A) New or amended California statewide regulations: Test Procedures 
for Determining the Efficiency of Gasoline Vapor Recovery Systems at 
Service Stations; Certification and Test Procedures for Vapor Recovery 
Systems of Gasoline Delivery Tanks; Test Procedure for Gasoline Vapor 
Leak Detection Using Combustible Gas Detector.
    (150) Revised regulations for the following APCD's submitted August 
2, 1983, by the Governor's designee.
    (i) Kings County APCD.
    (A) New Rule 414.4.
    (ii) Yuba County APCD.
    (A) Amended Rule 3.9.
    (151) [Reserved]
    (152) Amendments to ``Chapter 27--California Lead Control Strategy'' 
were submitted on February 22, 1984 by the Governor's designee.
    (153) Revised regulations for the following APCD's were submitted on 
March 14, 1984 by the Governor's designee.
    (i) Lake County APCD.
    (A) New or amended Rule 602.
    (ii) North Coast Unified AQMD.
    (A) New or amended Rules 100, 120, 130 [Paragraphs (d1) and (s5)], 
160 (except (a) and non-criteria pollutants), 240, 500, 520, 600, 610 
and Appendix B (except (D)(1)(e)).
    (B) New or amended Rules, 130, 130 (b1, m2, n1, p5, s2), 200 (a), 
(b), (c)(1-2), and (d), 220(c), and 260.
    (C) Previously approved on December 5, 1984 and now deleted without 
replacement Rules 600 and 610.
    (iii) San Diego APCD.
    (A) New or amended Rules 2, 52 and 53.

[[Page 134]]

    (B) Amended Rules 67.0 and 67.1 (deletion).
    (iv) San Joaquin APCD.
    (A) New or amended Rules 110, 202 and 407.
    (B) Amended Rules 409.1 and 409.4.
    (v) Bay Area AQMD.
    (A) New Regulation 8, Rules 31 and 32.
    (vi) Kern County APCD.
    (A) Amended Rule 410.1.
    (vii) South Coast AQMD.
    (A) New or amended Rules 1108.1 and 1141.1.
    (B) New Rule 1158, adopted 12-2-83.
    (viii) Ventura County APCD.
    (A) Amended Rule 74.2
    (154) Revised regulations for the following APCD's were submitted on 
April 19, 1984 by the Governor's designee.
    (i) Mendocino County APCD.
    (A) New or amended Regulation 1: Rules 100, 120, 130 [Paragraphs 
(d1) and (s5)], 160 (except (a) and non-criteria pollutants), 240, 500, 
520, 600, 610 and Appendix B (except (D)(1)(e)) and Regulation 2: Rules 
101, 102, 200, 301, 302, 303, 304, 305, 401, 501, and 502.
    (B) New or amended Rules, 130, 200, 220(a)(1&3), (b)(1, 2, 5, and 
7), (c), and 260.
    (C) Previously approved on December 5, 1984 and now deleted without 
replacement Rules 600 and 610.
    (ii) Monterey Bay Unified APCD.
    (A) New or amended Rules 101, 200, 203 and 422.
    (B) Amended Rule 426.
    (iii) Sacramento County APCD.
    (A) New or amended Rules 101, 102, 103, 403-410, 420, 501, 601, 602 
and 701.
    (B) Amended Rules 441, 442, 444-446 and 448-455.
    (C) Previously approved on December 5, 1984 and now deleted without 
replacement Rules 601 and 602.
    (iv) San Luis Obispo County APCD.
    (A) New or amended Rule 105.
    (v) Shasta County APCD.
    (A) New or amended Rules 1:2, 2:2 (repealed), 2:3 (repealed), 2:6 
2:26 (repealed), 2:27 (repealed), and 3:2.
    (B) Amended Rule 3:4, adopted on January 3, 1984.
    (vi) Bay Area AQMD.
    (A) New or amended Regulation 8, Rules 6, 7, 29 and 33.
    (B) Amended Regulation 9, Rule 4 adopted December 7, 1983.
    (vii) South Coast AQMD.
    (A) Amended Rule 1124.
    (B) [Reserved]
    (155) Revised regulations for the following APCD's submitted July 
10, 1984, by the Governor's designee.
    (i) Bay Area AQMD.
    (A) New or amended Regulation 8, Rules 11, 34 and 35.
    (ii) El Dorado County APCD.
    (A) New or amended Rules 215, 216 (deletion), 216 and 217 
(deletion).
    (B) New or amended Rule 217.
    (iii) Madera County APCD.
    (A) New or amended Rules 409 and 410.
    (B) New or amended Rules 203 and 404.
    (iv) South Coast AQMD.
    (A) Amended Rule 1113.
    (B) New or amended Rules 401 and 1305.
    (v) North Coast Unified AQMD.
    (A) New or amended Regulation 2.
    (B) New or amended Rules 130 (b2, m1, p3, and s7), Chapter II, 200 
(c)(3-6) and 220 (a) and (b).
    (vi) Shasta County APCD.
    (A) Amended Rule 1:2.
    (156) Revised regulations for the following APCD's were submitted on 
October 19, 1984 by the Governor's designee.
    (i) Bay Area AQMD.
    (A) New or amended Rules 2-1 and 8-36.
    (ii) Merced County APCD.
    (A) New or amended Rules 112, 409.1, and 409.4.
    (iii) North Coast Unified AQMD.
    (A) New or amended Rules 160 and 460.
    (B) Amended Rules 130(c, 1) and 240(e).
    (iv) San Diego County APCD.
    (A) New or amended Rules 61.0, 61.2, 61.8, and 67.3.
    (v) Yolo-Solano APCD.
    (A) New or amended Rule 2.21.
    (vi) Northern Sonoma County APCD.
    (A) New or amended Rules 130 (b2, m1, p3, p3a, and s7), Chapter II, 
220(B).
    (vii) South Coast AQMD.
    (A) New or amended Rule 463, adopted 6-1-84 and 1141.2, adopted 7-6-
84.
    (157) [Reserved]
    (158) Revised regulations for the following Districts were submitted 
on December 3, 1984 by the Governor's designee.

[[Page 135]]

    (i) Mendocino County APCD.
    (A) New or amended Rules 1-160, 1-240, 1-460 and 2-502.2.
    (B) New or amended Rules 130 (b2, m1, p3, s7), Chapter II, 220 
(a)(2) and (b)(3, 4, 6, 8 and 9).
    (159) Revised regulations for the following APCD's were submitted on 
February 6, 1985 by the Governor's designee.
    (i) Sacramento County APCD.
    (A) Amended Rule 202 (except for a) sections 104 and 105 as they 
apply to volatile organic compounds and nitrogen oxides, b) sections 109 
and 229, and c) the portion of section 405 which concerns stack heights 
[under NSR]).
    (ii) Fresno County APCD.
    (A) New or amended Rules 409.7 and 413.1, adopted on October 2, 
1984.
    (iii) Monterey Bay Unified APCD.
    (A) New or amended Rules 100 to 106, 200 to 206, 208 to 214, 400, 
401, 405, 406, 408 to 415, 417 to 422, 425 to 428, 500 to 506, 600 to 
617, 700 to 713, 800 to 816, and 900 to 904, adopted on December 13, 
1984.
    (B) Previously approved on July 13, 1987 and now deleted without 
replacement Rules 600 to 617 and 800 to 816.
    (iv) Sacramento County APCD.
    (A) New or amended Rules 201 (sections 100-400), 404 (sections 100-
300), and 443 (sections 100-400), adopted on November 20, 1984.
    (B) Amended Rule 447 adopted November 20, 1984.
    (v) South Coast AQMD.
    (A) New or amended Rules 1104 and 1125, adopted on December 7, 1984.
    (B) Amended Rule 1141, adopted on November 2, 1984.
    (C) Amended Rule 1105 adopted September 21, 1984.
    (D) New Rule 1117 adopted January 6, 1984.
    (vi) Stanislaus County APCD.
    (A) New or amended Rules 202(O), 411, and 416.1, adopted on 
September 18, 1984.
    (vii) Yolo-Solano County APCD.
    (A) Amended Rule 2.21.a.7. (a) and (b) adopted November 21, 1984.
    (160) Revised regulations for the following APCD's were submitted on 
April 12, 1985, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Bay Area AQMD.
    (1) Revisions to Regulation 8, Rule 33, adopted on January 9, 1985.
    (B) San Luis Obispo County APCD.
    (1) New or amended Rules 201, 205, 405, and 406, adopted on November 
13, 1984.
    (C) Shasta County APCD.
    (1) Amended Rule 2:1.514, adopted on May 29, 1984.
    (D) San Diego County APCD.
    (1) New Rule 67.10 adopted January 30, 1985.
    (E) South Coast AQMD.
    (1) Amended Rule 1108 adopted February 1, 1985.
    (161) Revisions to the ozone and carbon monoxide nonattainment area 
plans for the Fresno County portion of the San Joaquin Valley Air Basin 
were submitted by the Governor on June 11, 1984.
    (i) Incorporation by reference.
    (A) State of California Air Resources Board Executive Order G-125-46 
adopted May 11, 1984.
    (B) Letters from the County of Fresno to the Bureau of Automotive 
Repair dated March 14, 1984 and February 14, 1984 requesting 
implementation of an   I/M program in Fresno County.
    (C) County of Fresno Resolution File Number 18-13 adopted February 
14, 1984.
    (D) Schedule to implement I/M in Fresno County, adopted on February 
14, 1984.
    (ii) Additional Information. The State submitted no additional 
information.
    (162) Revised regulations for the following APCD were submitted on 
June 21, 1985 by the Governor's designee.
    (i) Northern Sonoma County APCD.
    (A) Amended Rule 220 (a).
    (163) Rule 1304(e), Resource Conservation and Energy Projects, 
adopted on March 7, 1980, submitted on April 3, 1980 (See 
Sec. 52.220(c)(68)(i)), and conditionally approved on January 21, 1981 
[See Sec. 52.232(a)(3)(i)(A)] is disapproved but only with respect to 
projects whose application for a permit is complete after January 1, 
1986.
    (164) Revised regulations for the following APCD's were submitted on 
October 16, 1985 by the Governor's designee.
    (i) Incorporation by reference.
    (A) Amador County APCD.

[[Page 136]]

    (1) New or amended Rules 301-319 and 501, adopted 6/16/81; and Rules 
502-514 and 517-521, adopted 1/8/80.
    (B) Northern Sonoma County APCD.
    (1) Amended Rules 100, 120, 130 (d1 and s5), 500, 520, 600, and 610, 
adopted 2/22/84, and amended Rule 200(a), adopted 7/19/83.
    (C) Ventura County APCD.
    (1) Amended Rules 15, 54, 61, 64, 67, 69, 70, 74.3, 74.4, 74.5, 
74.6, 74.8, 80, and 103, revised 7/5/83.
    (2) Previously approved and now removed (without replacement), Rule 
84.
    (D) Yuba County APCD.
    (1) Amended Rules 1.1, 2.0, 2.1, 2.3, 2.5, 2.6, 2.7, 2.9, 2.11, and 
2.16, adopted 3/5/85.
    (E) South Coast Air Quality Management District.
    (1) Rule 1150.1, adopted on April 5, 1985.
    (165) Revised regulations for the following APCD's were submitted by 
the Governor's designee on November 12, 1985.
    (i) Incorporation by reference.
    (A) Northern Sonoma County APCD.
    (1) Amended Rule 130 s4, adopted 7/9/85.
    (B) South Coast Air Quality Management District.
    (1) Amended Rule 221, adopted 1/4/85.
    (166) A revised regulation for the following district was submitted 
on December 2, 1983, by the Governor's designee.
    (i) Incorporation by reference.
    (A) South Coast AQMD.
    (1) Amended Rule 466 adopted 10/7/83.
    (167) A revised regulation for the following district was submitted 
on August 1, 1984, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Ventura County APCD.
    (1) Amended Rule 74.7 adopted 7-3-84.
    (168) Revised regulations for the following APCD's were submitted by 
the Governor's designee on February 10, 1986.
    (i) Incorporation by reference.
    (A) Butte County APCD.
    (1) New or amended Rules 101, 102, 250, 260, 261, 270, 301, 302, 
303, 304, 306, 307, 308, 309, 310, 311, 312, 313, 314, 315, 316, 317, 
318, 320, 322, 323, 324, 325, 401, 402, 403, 405, 406, 407, 420, 421, 
422, 423, 425, 601, 602, 603, 604, 605, 606, 607, 608, 609, 610, 611, 
612, 613, 614, 615, 616, 617, 618, 619, 620, 621, 701, 702, 703, 704, 
801, 802, 901, 902, and 3-3 (repealed), adopted August 6, 1985.
    (2) New or amended Rules 202, 203, 204, 205, 210, 211, 212, 213, 
214, 215, 220, 225, and 231 adopted August 6, 1985.
    (3) Previously approved on February 3, 1987 and now deleted without 
replacement Rules 601 to 618, 620 to 621, and 801 to 802.
    (B) Lake County APCD.
    (1) New Rules 650D, 651, and 1701Q, adopted December 10, 1985.
    (C) Placer County APCD (Mountain Counties portion).
    (1) Amended Rules 102, 312, 314, 315, 320, 505, 507, 803, 211A 
(repealed), and 219M (repealed), adopted May 20, 1985.
    (2) New or amended Rules 213, 307, and 324 adopted May 20, 1985.
    (D) Sutter County APCD.
    (1) Amended Rule 2.5, adopted October 15, 1985.
    (E) Tehama County APCD.
    (1) Amended Rules 2.12, 2.13, 2.14, 2.15, 2.16, 2.17, 5.2, 5.3, 5.6, 
5.7, 5.8, 5.9, 5.10, 5.11, 5.12, 5.13, 5.15, 5.16, 5.17, 5.18, 5.20, 
5.21, 5.22, and 5.23, adopted September 19, 1985.
    (2) New or amended Rules 4.3, 4.8, 4.9 (a) and (b), 4.10, and 4.14 
adopted September 10, 1985.
    (3) Previously approved on February 3, 1987 and now deleted without 
replacement Rules 5.2 to 5.3, 5.6 to 5.9, 5.11 to 5.12, 5.13, 5.15 to 
5.18, and 5.20 to 5.23.
    (F) Monterey Bay Unified APCD.
    (1) New or amended Rules 416 and 418 adopted September 18, 1985.
    (G) San Diego County APCD.
    (1) New or amended Rules 66 (w) and 67.8 (d) adopted September 17, 
1985.
    (H) South Coast AQMD.
    (1) Amended Rule 1159 adopted December 6, 1985.
    (2) Rule 1150.2, adopted on October 18, 1985.
    (169) [Reserved]
    (170) Revised regulations for the following APCD's were submitted on 
August 12, 1986, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Placer County Air Pollution Control District.
    (1) Amended rules 101, 201, 305 (Mountain Counties portion), adopted 
May 27, 1986.

[[Page 137]]

    (171) Revised regulations for the following APCD's were submitted on 
November 21, 1986 by the Governor's designee.
    (i) Incorporation by reference.
    (A) Mendocino County APCD.
    (1) Amended Rule 200(d), adopted on July 8, 1986.
    (B) Placer County APCD.
    (1) New Rule 225, adopted on June 17, 1986.
    (C) San Joaquin County APCD.
    (1) Amended Rules 411.2, 416, and 416.1, adopted on June 24, 1986.
    (D) Shasta County APCD.
    (1) New or amended Rules 1:1, 1:2 (except ``fugitive emissions''), 
2:10, 2:23, 2:26, 2:27, 3:2, 3:3, 4:1, 4:2, and 4:7 adopted on July 22, 
1986.
    (2) Previously submitted to EPA on June 30, 1972 and approved in the 
Federal Register on September 22, 1972 and now removed without 
replacement, Rule 2:13.
    (3) Previously submitted to EPA on July 19, 1974 and approved in the 
Federal Register on August 22, 1977 and now removed without replacement, 
Rules 3:8, 4:7, 4:9, 4:10, 4:11, 4:12, 4:13, 4:15, 4:16, 4:17, 4:18, 
4:20, 4:21, and 4:22.
    (4) Previously submitted to EPA on October 13, 1977 and approved in 
the Federal Register on November 14, 1978 and now removed without 
replacement, Rules 4:14 and 4:19.
    (5) Previously approved on April 12, 1989 and now deleted without 
replacement Rule 4.1.
    (172) Revised regulations for the following APCD's were submitted on 
March 11, 1987, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Siskiyou County APCD.
    (1) New or amended Rules 1.1, 1.2 (A3, A4, A8, A9, B3, B4, C1, C5, 
C6, C8, C10, D1, D2, E1, F1, H2, I2, I3, M3, M4, O1, P1, P3, P4, P8, R3, 
R4, R6, S1, S2, S3, S5, S6, T2, V1), 1.3, 1.5, 2.3, 2.7, 2.8, 2.9, 2.10, 
2.11, and 2.12 adopted on November 25, 1986.
    (2) Previously submitted to EPA on February 21, 1972 and approved in 
the Federal Register on May 31, 1972 and now removed without 
replacement, Rule 1.2 (M).
    (3) Previously submitted to EPA on July 25, 1973 and approved in the 
Federal Register on August 22, 1977 and now removed without replacement, 
Rule 2.13.
    (B) Ventura County APCD.
    (1) Amended Rule 23, adopted on October 21, 1986.
    (173) Revised regulations for the following APCD's were submitted on 
June 9, 1987 by the Governor's designee.
    (i) Incorporation by reference.
    (A) Bay Area AQMD.
    (1) New Rules 2-1-401.6 and 2-1-401.7, adopted January 7, 1987.
    (B) Imperial County APCD.
    (1) New or amended Rules 102, 105, 108, 110, 113, 115, 203, 204, 
205, 210, 401, 402, 403, 420, 421, 422, and 423, adopted November 19, 
1985.
    (C) Monterey Bay Unified APCD.
    (1) Amended Rule 201 (introductory paragraph and subparagraphs (1) 
through (8.6)), adopted December 17, 1986.
    (D) Tulare County APCD.
    (1) Amended Rules 110 and 202 (introductory paragraph and 
subparagraphs (a) through (d.7)), adopted May 13, 1986.
    (E) San Diego County Air Pollution Control District.
    (1) Amended Rules 61.7 and 61.8, adopted on January 13, 1987.
    (174) Revised regulations for the following APCD's were submitted on 
September 1, 1987 by the Governor's designee.
    (i) Incorporation by reference.
    (A) South Coast AQMD.
    (1) Amended Rule 212, adopted May 1, 1987.
    (B) Ventura County APCD.
    (1) Amended Rule 12, adopted June 16, 1987.
    (175) Revised regulations for the following APCD's were submitted on 
November 25, 1987, by the Governor's designee.
    (i) Incorporation by Reference.
    (A) Shasta County AQMD.
    (1) Amended rules 1:2, 2:6.a.4.(c), 2:6.b, 2:7.a, 2:7.c, 
2:8.c.2.(a), 2:8.c.3.(a), 2:8.c.4, and 2:19, adopted on July 28, 1987.
    (B) Tehama County APCD.
    (1) New or amended rules 1:2, 3:1, 3:6(1), 3:11(a), 3:12, 3:13.j, 
3:14(10), 3:15, 4:3, and 4:24, adopted on August 4, 1987.
    (C) Yolo-Solano APCD.
    (1) Amended rule 3:7(d), adopted on August 12, 1987.
    (176) Revised regulations for the following APCD's were submitted on

[[Page 138]]

March 23, 1988 by the Governor's designee.
    (i) Incorporation by reference.
    (A) Siskiyou County Air Pollution Control District.
    (1) New and amended rules 4.1, 4.1-1, 4.1-2, 4.2-1, 4.3, 4.4, 4.5, 
4.6, 4.6-1, 4.7, 4.8, 4.9, 4.10, 4.11, 7.1, 7.2, 7.3, 7.4, 7.5-1, 7.5-2, 
7.5-3, 7.6, and 7.7 adopted on October 27, 1987.
    (B) Lake County Air Pollution Control District.
    (1) Amended rules 431.5, 431.7, 432, 432.5, 433, 434, 436.5, 442, 
1105, and 1107 adopted October 20, 1987.
    (C) Lassen County Air Pollution Control District.
    (1) Amended Articles I, II, III, IV, V, VI, and VII adopted August 
11, 1987.
    (177) Revised regulations for the following APCD's were submitted by 
the Governor's designee on February 7, 1989.
    (i) Incorporation by reference.
    (A) Ventura County Air Pollution Control District.
    (1) Amended Rules 2 and 55 adopted May 24, 1988.
    (2) Amended Rule 56 adopted May 24, 1988.
    (B) Bay Area Air Quality Management District.
    (1) Amended Regulation 4 adopted September 7, 1988.
    (C) Mariposa County Air Pollution Control District.
    (1) Amended Regulation III and Rules 300, 301, 302, 303, 304, 305, 
306, 307, and 308 adopted July 19, 1988.
    (D) Madera County Air Pollution Control District.
    (1) Amended rules 106, 112, 114, 401, 403, 422, 424, 425, 501, 504, 
505, 506, 518, 519, 601, 603, 605, 606, 609, 610, 611, 613, and 614 
adoped on January 5, 1988.
    (2) Previously approved on April 16, 1991 and now deleted without 
replacement Rules 106, 501, 504 to 506, and 519.
    (E) Bay Area Air Quality Management District.
    (1) Rule 8-5 adopted on May 4, 1988.
    (178) [Reserved]
    (179) Revised regulations for the following APCD's were submitted on 
March 26, 1990, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Kings County Air Pollution Control District.
    (1) Amended Rules 417 and 417.1 adopted on February 28, 1989.
    (B) San Bernardino County Air Pollution District.
    (1) Amended Rules 101, 102 (except fugitive liquid leak and fugitive 
vapor leak), 103, 104, 105, and 106 adopted on December 19, 1988.
    (C) Bay Area Air Quality Management District.
    (1) Rule 8-44, adopted January 4, 1989.
    (D) Ventura County Air Pollution Control District.
    (1) Rule 74.7, adopted on January 10, 1989.
    (E) Siskiyou County Air Pollution Control District.
    (1) Rules 1.2 (except section V1), 1.4, 2.1, 2.2, 2.10. 4.1, 4.6, 
6.1, and Appendix A, adopted on January 24, 1989.
    (180) [Reserved]
    (181) New and amended regulations for the following APCD were 
submitted on October 16, 1990, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Ventura County Air Pollution Control District.
    (1) Rule 71.2, adopted on September 26, 1989.
    (182) New and amended regulations for the following APCDs were 
submitted on December 31, 1990, by the Governor's designee.
    (i) Incorporation by reference.
    (A) South Coast Air Quality Management District.
    (1) Rules 1175 and 1176, adopted on January 5, 1990.
    (2) Rule 109, adopted on May 5, 1989.
    (3) Rule 108, adopted on April 6, 1990.
    (4) Rule 461, adopted on July 7, 1989.
    (B) Bay Area Air Quality Management District.
    (1) Regulation 8, Rule 8, adopted on November 1, 1989.
    (2) Amended Rule 8-28, adopted September 6, 1989.
    (3) Rule 8-46, adopted July 12, 1989.
    (4) Amended Regulation 8, Rule 16, adopted on August 2, 1989.
    (5) Amended Regulation 8, Rule 11, adopted on September 20, 1989.
    (C) San Luis Obispo County Air Pollution Control District.
    (1) Rule 424, adopted on July 18, 1989.
    (D) Santa Barbara County Air Pollution Control District.

[[Page 139]]

    (1) Amended Rule 323, adopted on February 20, 1990.
    (E) San Diego County Air Pollution Control District.
    (1) Amended Rules 101, 102, 103, and 108, adopted March 27, 1990.
    (183) New and amended regulations for the following APCD's were 
submitted on April 5, 1991, by the Governor's designee.
    (i) Incorporation by reference.
    (A) San Diego County Air Pollution Control District.
    (1) Rule 67.8, adopted on December 18, 1990.
    (2) Rule 61.9, adopted on March 14, 1989, is now removed without 
replacement as of April 19, 1994.
    (3) Revised Rule 67.3, adopted on October 16, 1990.
    (4) Amended Rule 61.4, adopted on October 16, 1990.
    (5) Amended Rule 67.4, adopted July 3, 1990.
    (6) Amended Rule 61.0, adopted on September 16, 1990.
    (7) New Rule 67.12, adopted December 4, 1990.
    (8) [Reserved]
    (9) Amended Rule 67.18, adopted on July 3, 1990.
    (10) Revised Rules 61.2, 61.3, and 67.5, adopted October 16, 1990.
    (11) Amended Rule 61.1, adopted October 16, 1990.
    (12) Rule 67.6, adopted on October 16, 1990.
    (13) Rule 67.15, adopted on December 18, 1990.
    (B) Ventura County Air Pollution Control District.
    (1) Rules 74.5.1 and 74.5.2, adopted on December 4, 1990.
    (2) Rule 71, adopted on September 11, 1990.
    (3) Rule 74.13, adopted on January 22, 1991.
    (C) Placer County Air Pollution Control District.
    (1) Amended Rule 217, adopted on September 25, 1990.
    (2) Amended Rule 213, adopted on September 25, 1990.
    (3) New Rule 410 and Amended Rule 223, adopted on September 25, 
1990.
    (4) Amended Rule 212, adopted September 25, 1990.
    (5) Rule 216, adopted on September 25, 1990.
    (D) Sacramento Metropolitan Air Quality Management District.
    (1) Amended rules 443, adopted September 25, 1990, and 452, adopted 
August 21, 1990.
    (E)(1) [Reserved]
    (2) Rule 316, adopted on July 10, 1990.
    (F) Bay Area Air Quality Management District.
    (1) Amended Regulation 8, Rule 43, adopted on June 20, 1990.
    (2) Regulation 8, Rule 17, adopted on September 5, 1990.
    (184) New and amended regulations for the following APCDs were 
submitted on y 13, 1991, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Sacramento Metropolitan Air Quality Management District.
    (1) Amended rule 445, adopted November 6, 1990.
    (2) Amended Rules 442, adopted October 2, 1990, and 446, adopted 
December 4, 1990.
    (B) South Coast Air Quality Management District.
    (1) Rules 1102 and 1102.1, adopted on December 7, 1990.
    (2) Rule 465, adopted on December 7, 1990, and Rule 1123, adopted on 
December 7, 1990.

    Editorial Note: At 57 FR 48459, Oct. 26, 1992, the following 
paragraph (c)(184)(i)(B)(2) was added to Sec. 52.220.
    (2) Rules 1162 and 1173, adopted on December 7, 1990.
    (3) Rules 1153 and 1164, adopted on January 4, 1991, and December 7, 
1990, respectively.
    (4) New Rule 1174, adopted on October 5, 1990.
    (5) Rule 1103, adopted on December 7, 1990.
    (6) Rule 464, adopted on December 7, 1990.
    (C) Bay Area Air Quality Management District.
    (1) Rule 8-37, adopted on October 17, 1990.
    (D)(1) Amended Rule 67.0, adopted on December 4, 1990.
    (E) Yolo-Solano Air Quality Management District.
    (1) Rule 2.24, adopted on November 14, 1990.

[[Page 140]]

    (185) New and amended regulations for the following APCD's were 
submitted on May 30, 1991, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Kern County Air Pollution Control District.
    (1) Rules 410.6 and 410.6A, adopted on May 6, 1991.
    (2) Rule 410.5, adopted on May 6, 1991.
    (3) Rule 410.4A, adopted on May 6, 1991.
    (4) Amended Rule 410.1, adopted on May 6, 1991.
    (5) Amended Rules 414 and 414.1 and New Rule 414.5, adopted on May 
6, 1991.
    (6) Revised Rule 410.4, adopted on May 6, 1991.
    (7) Rule 410.3 and Rule 412, adopted on May 6, 1991.
    (8)  [Reserved]
    (9) Rule 410.7, adopted May 6, 1991.
    (B) San Diego County Air Pollution Control District.
    (1) Rule 67.2, adopted on May 21, 1991.
    (2) Rule 67.7, adopted on May 21, 1991.
    (3) [Reserved]
    (4) Amended Rule 67.16, adopted on May 21, 1991.
    (5) Rule 67.1, adopted on May 21, 1991.
    (C) San Joaquin Valley Unified Air Pollution Control District.
    (1) Rules 467.1 and 467.2, adopted on April 11, 1991.
    (2) Rule 460.2, adopted on April 11, 1991.
    (3) New Rule 460.1, adopted on April 11, 1991.
    (4) New Rules 463.4, 464.1, and 464.2, adopted on April 11, 1991.
    (5) New Rule 461.2, adopted on April 11, 1991.
    (6) Amended Rules 465.3 and 466.1, adopted April 11, 1991.
    (D) Placer County Air Pollution Control District.
    (1) Amended Rule 215, adopted on September 25, 1990.
    (186) New and amended regulations for the following APCDs were 
submitted on October 25, 1991, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Sacramento Metropolitan Air Quality Management District.
    (1) Amended Rules 447 adopted April 30, 1991.
    (B) San Joaquin Valley Unified Air Pollution Control District.
    (1) Rule 468.1, adopted on May 16, 1991.
    (C) South Coast Air Quality Management District.
    (1) Rule 1104, adopted March 1, 1991.
    (D) Ventura County Air Pollution Control District.
    (1) Rule 62.6, adopted on July 16, 1991.
    (2) Rule 103, adopted on June 4, 1991.
    (187) New and amended regulations for the following APCDs were 
submitted on January 28, 1992, by the Governor's designee.
    (i) Incorporation by reference.
    (A) San Joaquin Valley Unified Air Pollution Control District.
    (1) Rule 463.1, adopted on September 19, 1991.
    (2) Rule 460.2 adopted on September 19, 1991.
    (3) New Rule 463.2, adopted on September 19, 1991.
    (4) New Rule 460.4, adopted on September 19, 1991.
    (5) Rule 461.1 and Rule 465.2, adopted on September 19, 1991.
    (6) Rule 465.1, adopted on September 19, 1991.
    (B) Ventura County Air Pollution Control District.
    (1) New Rule 74.17, adopted on September 17, 1991.
    (C) South Coast Air Quality Management District.
    (1) Rule 1142, adopted on June 19, 1991.
    (188) New and amended regulations for the following APCDs were 
submitted on June 19, 1992, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Santa Barbara County Air Pollution Control District.
    (1) Rule 339, adopted on November 5, 1991.
    (2) Rule 331, adopted on December 10, 1991.
    (3) Rule 342, adopted on March 10, 1992.
    (4) Rule 329, adopted on February 25, 1992.
    (B) San Bernardino County Air Pollution Control District.
    (1) Rule 1116, adopted on March 2, 1992.
    (C) South Coast Air Quality Management District.
    (1) Rule 1171, adopted on August 2, 1991.

[[Page 141]]

    (D) Ventura County Air Pollution Control District.
    (1) Rule 74.18, adopted on January 28, 1992.
    (2) Rule 74.6, adopted on December 10, 1991.
    (3) Rule 74.3, adopted on December 10, 1991.
    (E) [Reserved]
    (F) Sacramento Metropolitan Air Quality Management District.
    (1) Rules 448 and 449 adopted on December 17, 1991.
    (189) New and amended regulations for the following APCDs were 
submitted on September 14, 1992, by the Governor's designee.
    (i) Incorporation by reference.
    (A) South Coast Air Quality Management District.
    (1) Rule 1115, adopted on March 6, 1992.
    (2) Rule 1126, adopted on March 6, 1992.
    (3) Rule 1128, adopted on February 7, 1992, and Rule 1141, adopted 
on April 3, 1992.
    (4) Rules 1125 and 1136, adopted on August 2, 1991.
    (5) New Rule 1179, adopted March 6, 1992.
    (6) Rule 109 adopted on March 6, 1992, and Rule 1106.1 adopted on 
May 1, 1992.
    (B) Ventura County Air Pollution Control District.
    (1) Rule 71.1 and Rule 71.3, adopted on June 16, 1992.
    (2) Rule 74.10, adopted on June 16, 1992.
    (3) Rule 74.14, adopted on May 26, 1992.
    (C) Bay Area Air Quality Management District.
    (1) Rule 8-49, adopted on August 21, 1992.
    (190) New and amended regulations for the following APCDs were 
submitted on November 12, 1992, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Ventura County Air Pollution Control District.
    (1) Revised Rule 74.19, adopted August 11, 1992.
    (B) Bay Area Air Quality Management District.
    (1) Rule 8-18, adopted on March 4, 1992.
    (191) New and amended regulations for the following APCDs were 
submitted on January 11, 1993, by the Governor's designee.
    (i) Incorporation by reference.
    (A) South Coast Air Quality Management District.
    (1) Rule 1145, adopted on January 10, 1992.
    (B) Santa Barbara County Air Pollution Control District.
    (1) Rule 346, adopted on October 13, 1992.
    (C) San Bernardino County Air Pollution Control District.
    (1) Rule 463, adopted on November 2, 1992.
    (D) Kern Couny Air Pollution Control District.
    (1) Rule 412.1, adopted on November 9, 1992.
    (192) New and amended regulations for the following APCDs were 
submitted on April 6, 1993, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Sacramento Air Quality Management District.
    (1) Rule 456, adopted on February 23, 1993.
    (2) Rule 454, adopted on February 23, 1993.
    (3) Revised Rule 450, adopted February 23, 1993.
    (193) New and amended regulations for the following APCDs were 
submitted on May 13, 1993, by the Governor's designee.
    (i) Incorporation by reference.
    (A) South Coast Air Quality Management District.
    (1) Rule 1106, adopted on August 2, 1991; Rule 1107, adopted on 
August 2, 1991; and Rule 1151, adopted on September 6, 1991.
    (2) Rule 1130 adopted on March 6, 1992.
    (3) Rule 1122, adopted on April 5, 1991.
    (B) San Luis Obispo County Air Pollution Control District.
    (1) Rule 417, adopted February 9, 1993.
    (C) Butte County Air Pollution Control District.
    (1) Rule 241, adopted on January 12, 1993.
    (D) Glenn County Air Pollution Control District.
    (1) Section 51, adopted on March 16, 1993.

[[Page 142]]

    (194) New and amended regulations for the following APCDs were 
submitted on November 18, 1993, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Ventura County Air Pollution Control District.
    (1) Rule 70, adopted on May 4, 1993; Rule 71, adopted on June 8, 
1993; and Rule 71.4, adopted on June 8, 1993.
    (2) Rule 59, adopted on September 15, 1992.
    (3) Rule 74.15.1, adopted on May 11, 1993.
    (4) Rule 74.21, adopted on April 6, 1993.
    (5) Rule 74.20, adopted on June 8, 1993.
    (B) Kern County Air Pollution Control District.
    (1) Rule 410.4, adopted on July 12, 1993.
    (2) Rule 425, adopted on August 16, 1993.
    (3) Previously submitted to EPA on June 28, 1982 and approved in the 
Federal Register on May 3, 1984 and now removed without replacement, 
Rule 425.
    (C) San Joaquin Valley Unified Air Pollution Control District.
    (1) Rule 4603, adopted on May 20, 1993.
    (2) Rule 4621, adopted on May 20, 1993.
    (D) Santa Barbara County Air Pollution Control District.
    (1) Rule 349, adopted on April 27, 1993.
    (E) San Diego County Air Pollution Control District.
    (1) Rule 67.12, adopted on April 6, 1993.
    (2) Amended Rule 19, adopted April 6, 1993.
    (F) Monterey Bay Unified Air Pollution Control District
    (1) Rule 417, Rule 418, and Rule 427, adopted on August 25, 1993.
    (2) Rule 425, adopted on August 25, 1993.
    (3) Rule 420 and Rule 426, adopted on August 25, 1993.
    (4) Previously submitted to EPA on February 6, 1975 and approved in 
the Federal Register on July 13, 1987 and now removed without 
replacement, Rule 428.
    (5) Rule 300--Regulation 3, Part 4, Paragraph 4.4 adopted on June 9, 
1993.
    (195) New and amended regulations for the following APCDs were 
submitted on February 11, 1994, by the Governor's designee.
    (i) Incorporation by reference.
    (A) San Diego Air Pollution Control District.
    (1) Rule 67.17, adopted on September 21, 1993.
    (B) Ventura County Air Pollution Control District.
    (1) Rule 74.22, adopted on November 9, 1993.
    (2) Rule 59, adopted on October 12, 1993.
    (196) New and amended regulations for the following APCDs were 
submitted on March 29, 1994 by the Governor's designee.
    (i) Incorporation by reference.
    (A) Sacramento Metropolitan Air Quality Management District.
    (1) Sacramento Metropolitan AQMD rules 442, 443, 446, 447, and 452 
adopted on November 16, 1993.
    (B) Ventura County Air Pollution Control District.
    (1) Rule 74.9, adopted on December 21, 1993.
    (C) Santa Barbara County Air Pollution Control District.
    (1) Rule 316, adopted on December 14, 1993.
    (2) Rules 325 & 326, adopted on January 25, 1994 and December 14, 
1993, respectively.
    (3) Rule 343, adopted on December 14, 1993.
    (D) Yolo-Solano Air Quality Management District.
    (1) Rule 3.2, adopted on August 25, 1993; and rules 3.14 and 3.15, 
adopted on September 22, 1993.
    (197) New and amended regulations for the following APCDs were 
submitted on May 24, 1994, by the Governor's designee.
    (i) Incorporation by reference.
    (A) South Coast Air Quality Management District.
    (1) Rules 1162, 1173, 1175 and 1176, adopted on May 13, 1994.
    (2) Rule 463, adopted on March 11, 1994.
    (B) Bay Area Air Quality Management District.
    (1) Rule 8-6, adopted on February 2, 1994. Rule 8-5, adopted on 
January 20, 1993.
    (C) San Joaquin Valley Unified Air Pollution Control District.

[[Page 143]]

    (1) Rule 4622, adopted on February 17, 1994.
    (D) Ventura County Air Pollution Control District.
    (1) Rule 74.24, adopted on March 8, 1994.
    (198) New and amended regulations for the following APCDs were 
submitted on July 13, 1994, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Bay Area Air Quality Management District.
    (1) Revised Rule 8-8, adopted on June 15, 1994.
    (B) Placer County Air Pollution Control District.
    (1) Rule 230, adopted on June 28, 1994.
    (C) San Joaquin Valley Unified Air Pollution Control District.
    (1) Rule 4407, adopted on May 19, 1994.
    (2) Rule 4682 adopted on June 16, 1994 and Rule 4684 adopted on May 
19, 1994.
    (3) Rule 4607, adopted on May 19, 1994.
    (D) Sacramento Metropolitan Air Quality Management District.
    (1) Rule 458, adopted on June 7, 1994.
    (E) Mojave Desert Air Quality Management District.
    (1) Rules 461 and 462, adopted on May 25, 1994.
    (2) Rule 1117 adopted June 22, 1994.
    (F) Monterey Bay Unified Air Pollution Control District.
    (1) Rule 430, adopted on May 25, 1994.
    (2) Rule 416, adopted April 20, 1994.
    (G)  [Reserved]
    (H) South Coast Air Quality Management District.
    (1) Rule 1146 and Rule 1146.1, adopted May 13, 1994.
    (I) San Diego County Air Pollution Control District.
    (1) Rule 67.10, adopted on June 15, 1994.
    (J) Ventura County Air Pollution Control District.
    (1) Rule 74.28, adopted on May 10, 1994.
    (2) Rule 74.30 adopted May 17, 1994.
    (K) Santa Barbara County Air Pollution Control District.
    (1) Rule 354, adopted June 28, 1994.
    (199) New and amended regulations for the following APCDs were 
submitted on September 28, 1994 by the Governor's designee.
    (i) Incorporation by reference.
    (A) Bay Area Air Quality Management District.
    (1) Regulation 8, Rules 11 and 16 adopted on June 15, 1994, and 
Regulation 8, Rule 28 adopted on June 1, 1994.
    (2) Regulation 8, Rules 14 and 43 adopted on June 1, 1994, and 
regulation 8, Rules 13, 23, 47 adopted on June 15, 1994.
    (3) Rules 8-25 and 8-42, adopted on June 1, 1994 and Rule 8-50, 
adopted on June 15, 1994.
    (4) Rule 8-22, adopted on June 1, 1994.
    (5) Rules 8-29, 8-33, and 8-39, adopted on June 1, 1994, and Rules 
8-19 and 8-38, adopted on June 15, 1994.
    (6) Rules 8-4, 8-7, 8-15, 8-31, and 8-41 adopted on June 1, 1994. 
Rules 8-1, 8-2, 8-12, 8-20, 8-24, 8-30, 8-34, 8-35, and 8-40 adopted on 
June 15, 1994. Rule 8-32 adopted on July 6, 1994.
    (B) San Luis Obispo County Air Pollution Control District.
    (1) Rule 419, adopted July 12, 1994.
    (C) Monterey Bay Unified Air Pollution Control District.
    (1) Rules 433 and 434, adopted June 15, 1994.
    (D) San Joaquin Valley Unified Air Pollution Control District.
    (1) Rule 4352, adopted on September 14, 1994.
    (2) Rule 4354, adopted on September 14, 1994.
    (200) Program elements were submitted on November 13, 1992 by the 
Governor's designee.
    (i) Incorporation by reference.
    (A) Small Business Stationary Source Technical and Environmental 
Compliance Assistance Program, adopted on October 15, 1992.
    (201)  [Reserved]
    (202) New and amended regulations for the following APCDs were 
submitted on October 19, 1994, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Bay Area Air Quality Management District.
    (1) Rule 2-1, adopted on June 15, 1994.
    (B) [Reserved]
    (C) San Diego County Air Pollution Control District. (1) Rule 67.4, 
adopted on September 27, 1994.
    (2) Rule 67.16, adopted on September 20, 1994.
    (3) Rule 69.2, adopted on September 27, 1994.
    (4) Rule 68, adopted on September 20, 1994.

[[Page 144]]

    (5) Rule 69.4, adopted on September 27, 1994.
    (6) Rule 69.3, adopted on September 27, 1994.
    (D) Mojave Desert Air Quality Management District.
    (1) Rule 464, adopted August 24, 1994.
    (E) Placer County Air Pollution Control District.
    (1) Rule 250, adopted on October 17, 1994.
    (2) Rule 233, adopted on October 6, 1994.
    (F) Yolo-Solano Air Quality Management District.
    (1) Rule 3.1, adopted on February 23, 1994.
    (203)  [Reserved]
    (204) New and amended plans and regulations for the following 
agencies were submitted on November 15, 1994, by the Governor's 
designee.
    (i) Incorporation by reference.
    (A) California Air Resources Board.
    (1) Title 17, California Code of Regulations, Subchapter 8.5, 
Consumer Products, Article 1, Antiperspirants and Deodorants, Sections 
94500-94506.5 and Article 2, Consumer Products, Sections 94507-94517, 
adopted on December 27, 1990, August 14, 1991, and September 21, 1992.
    (2) Title 13, California Code of Regulations, Diesel Fuel 
Regulations, Sections 2281-2282, adopted on August 22, 1989, June 21, 
1990, April 15, 1991, October 15, 1993, and August 24, 1994.
    (3) Title 13, California Code of Regulations, Reformulated Gasoline 
Regulations, Sections 2250, 2252, 2253.4, 2254, 2257, 2260, 2261, 
2262.1, 2262.2, 2262.3, 2262.4, 2262.5, 2262.6, 2262.7, 2263, 2264, 
2266-2272, and 2296, 2297, adopted on April 1, 1991, May 23, 1991, and 
September 18, 1992.
    (4) Long Term Measures, Improved Control Technology for Light-Duty 
Vehicles (Measure M2), Off-Road Industrial Equipment (Diesel), Consumer 
Products Long-Term Program (Measure CP4), and Additional Measures 
(Possible Market-Incentive Measures and Possible Operational Measures 
Applicable to Heavy-Duty Vehicles), as contained in ``The California 
State Implementation Plan for Ozone, Volume II: The Air Resources 
Board's Mobile Source and Consumer Products Elements,'' adopted on 
November 15, 1994.
    (5) Mid-Term Measures, Accelerated Ultra-Low Emission Vehicle (ULEV) 
requirement for Medium-Duty Vehicles (Measure M3), Heavy-Duty Vehicles 
NOX regulations (Measure M5), Heavy-Duty Gasoline Vehicles 
lower emission standards (Measure M8), Industrial Equipment, Gas & LPG--
3-way catalyst technology (Measure M11), Mid-Term Consumer Products 
(Measure CP-2), as contained in The California State Implementation Plan 
for Ozone, Volume II: The Air Resources Board's Mobile Source and 
Consumer Products Elements, adopted on Nov. 15, 1994.
    (6) State control measures: Accelerated Retirement of LDV's (Measure 
M1), Early Introduction of 2g/bhp-hr Heavy Duty Diesel Vehicles (Measure 
M4), Accelerated Retirement of Heavy-Duty Vehicles (Measure M7), Aerosol 
Paints (Measure CP3), and California Department of Pesticide 
Regulation's Pesticide Plan, as contained in ``The California State 
Implementation Plan for Ozone, Volume II: The Air Resources Board's 
Mobile Source and Consumer Products Elements,'' adopted on November 15, 
1994, and tables of local agency control measures and revisions to local 
Rate-of-Progress plan elements as contained in ``The California State 
Implementation Plan for Ozone, Volume IV: ``Local Plans,'' adopted on 
November 15, 1994.
    (B) South Coast Air Quality Management District.
    (1) Long Term Measures, Advance Technology for Coating Technologies 
(Measure ADV-CTS-01), Advance Technology for Fugitives (Measure ADV-
FUG), Advance Technologies for Process Related Emissions (Measure ADV-
PRC), Advance Technologies for Unspecified Stationary Sources (Measure 
ADV-UNSP), and Advance Technology for Coating Technologies (Measure ADV-
CTS-02), as contained in the ``1994 Air Quality Management Plan,'' 
adopted on September 9, 1994.
    (2) Control measures, emissions inventory, modeling, and ozone 
attainment demonstration, as contained in ``1994 Air Quality Management 
Plan,'' adopted on September 9, 1994.
    (C) San Diego Air Pollution Control District.
    (1) Emissions inventory, 15% Rate-of-Progress plan, Post-1996 Rate-
of-

[[Page 145]]

Progress plan, modeling, and ozone attainment demonstration, as 
contained in ``1994 Ozone Attainment and Rate-of-Progress Plans for San 
Diego County,'' adopted on November 1, 1994.
    (D) San Joaquin Valley Unified Air Pollution Control District.
    (1) Control measures, emissions inventory, 15% Rate-of-Progress 
plan, Post-1996 Rate-of-Progress plan, modeling, and ozone attainment 
demonstration, as contained in ``San Joaquin Valley Attainment and Rate-
of-Progress Plans,'' adopted on November 14, 1994.
    (E) Ventura County Air Pollution Control District.
    (1) Control measures, emissions inventory, 15% Rate-of-Progress 
plan, Post-1996 Rate-of-Progress plan, modeling, and ozone attainment 
demonstration, as contained in ``1994 Air Quality Management Plan for 
Ventura County,'' adopted on November 8, 1994.
    (F) Mojave Desert Air Quality Management District.
    (1) Control measures, emissions inventory, modeling, and ozone 
attainment demonstration, as contained in ``Rate-of-Progress and 
Attainment Demonstration Plans for the Mojave Desert,'' adopted on 
October 26, 1994.
    (205)(i)(A) Kern County Air Pollution Control District.
    (1) Emissions inventory, modeling, and ozone attainment 
demonstration, as contained in ``Rate-of-Progress and Attainment 
Demonstration Plans for the Kern County Air Pollution Control 
District,'' adopted on December 1, 1994.
    (B) Bay Area Air Quality Management District.
    (1) Amendments to the San Francisco Bay Area Redesignation Request 
and Maintenance Plan for the National Ozone Standard and 1990 Emissions 
Inventory adopted on September 7, 1994 by the Bay Area Air Quality 
Management District, October 5, 1994 by the Metropolitan Transportation 
Commission, and August 24, 1994 by the Association of Bay Area 
Governments.
    (206) Amended rule for the following APCD was submitted on November 
23, 1994, by the Governor's designee.
    (i) Incorporation by reference.
    (A) San Diego County Air Pollution Control District.
    (1) Rule 67.3, adopted on November 1, 1994.
    (207) New and amended regulations for the following APCDs were 
submitted on November 30, 1994, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Placer County Air Pollution Control District.
    (1) Rule 223, adopted on October 6, 1994.
    (2) Rules 101, 102, 103, 201, 202, 203, 204, 208, 209, 210, 211, 
213, 214, 217, 219, 220, 221, 222, 225, 226, 228, 406, 407, and 408, 
adopted on October 19, 1993; deletion of 104 for Lake Tahoe Air Basin 
and Mountain Counties Air Basin submitted on 08/21/ 79 and 10/15/79, 
respectively.
    (B) El Dorado County Air Pollution Control District.
    (1) Rule 224, adopted on September 27, 1994.
    (2) Rule 231, adopted September 27, 1994.
    (3) Rule 215, adopted on September 27, 1994.
    (4) Rules 225 and 230 adopted September 27, 1994.
    (C) Yolo-Solano Air Quality Management District.
    (1) Rule 2.21, adopted on March 23, 1994.
    (2) Rule 2.28, adopted on May 25, 1994.
    (3) Rules 2.25 and 2.33, adopted April 27, 1994 and September 14, 
1994, respectively.
    (4) Rule 2.13 adopted May 25, 1994.
    (5) Rule 2.35, adopted on September 14, 1994.
    (D) Mojave Desert Air Quality Management District.
    (1) Rule 1102, adopted October 26, 1994.
    (2) Rule 1104 adopted September 28, 1994.
    (3) Rule 1157 and Rule 1160, adopted on October 26, 1994.
    (E) Monterey Bay Unified Air Pollution Control District.
    (1) Rule 419, adopted on November 23, 1994.
    (208) New and amended regulations for the following APCDs were 
submitted on December 19, 1994, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Placer County Air Pollution Control District.

[[Page 146]]

    (1) Rule 410, adopted on November 3, 1994.
    (2) Rule 212, adopted on November 3, 1994.
    (209) Redesignation Request and Ozone Maintenance Plan for the 
redesignation of the Monterey Bay Unified Air Pollution Control District 
submitted on July 14, 1994 and November 14, 1994, respectively, by the 
Governor's designee.
    (i) Incorporation by reference.
    (A) Maintenance Plan for the redesignation of the Monterey Bay Area 
adopted on October 19, 1994 by the Monterey Bay Unified Air Pollution 
Control District, October 12, 1994 by the Association of Monterey Bay 
Area Governments, and October 6, 1994 by the Council of San Benito 
County Governments.
    (210) New and amended regulations for the following APCDs were 
submitted on December 22, 1994 by the Governor's designee.
    (i) Incorporation by reference.
    (A) Bay Area Air Quality Management District.
    (1) Rule 8-45, adopted on November 2, 1994.
    (B) San Diego County Air Pollution Control District.
    (1) Rule 67.18, adopted on December 13, 1994.
    (C) Mojave Desert Air Quality Management District.
    (1) Rule 1103, adopted on December 21, 1994.
    (2) Rule 471, adopted on December 21, 1994.
    (D) Monterey Bay Unified Air Pollution Control District.
    (1) Rule 1002, adopted on November 23, 1994.
    (E) San Joaquin Valley Unified Air Pollution Control District.
    (1) Rule 4651, adopted on December 17, 1992.
    (211) Revised Clean Air Plans for ozone for the following APCDs 
submitted on November 14, 1994, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Santa Barbara Air Pollution Control District
    (1) TCM-5, Improve Commuter Public Transit Service, adopted on 
November 2, 1994
    (2) Emissions inventory, 15% Rate-of-Progress plan, and control 
measures, as contrained in ``1994 Clean Air Plan for Santa Barbara 
County,'' adopted on November 2, 1994.
    (212) Ozone redesignation request for the Bay Area Air Quality 
Management District submitted on November 5, 1993, by the Governor's 
designee.
    (i) Incorporation by reference.
    (A) Redesignation request for the San Francisco Bay Area and the 
Ozone Maintenance Plan for the National Ozone Standard adopted on 
September 1, 1993 by the Bay Area Air Quality Management District, 
September 22, 1993 by the Metropolitan Transportation Commission, and 
September 16, 1993 by the Association of Bay Area Governments.
    (213) California Statewide emission inventory submitted on March 30, 
1995, by the Governor's designee.
    (i) Incorporation by reference.
    (A) California Air Resources Board.
    (1) 1990 Base-Year Emission Inventory for Ozone Nonattainment Areas 
in California.
    (i) Sacramento, San Diego, San Joaquin Valley, South Coast, 
Southeast desert, Ventura.
    (ii) Santa Barbara.
    (iii) Monterey Bay Area.
    (214) New and amended regulations for the following APCDs were 
submitted on January 24, 1995, by the Governor's designee.
    (i) Incorporation by reference.
    (A) South Coast Air Quality Management District.
    (1) Rule 1151, adopted on December 9, 1994.
    (B) San Diego County Air Pollution Control District.
    (1) Rule 61.1 adopted on January 10, 1995.
    (C) Santa Barbara County Air Pollution Control District.
    (1) Rule 337, adopted October 20, 1994.
    (2) Rule 344, adopted on November 10, 1994.
    (D) Ventura County Air Pollution Control District.
    (1) Rule 74.15, adopted on November 8, 1994.
    (2) Rule 74.26 and Rule 74.27, adopted on November 8, 1994.
    (E) Placer County Air Pollution Control District.

[[Page 147]]

    (1) Rule 215, adopted on November 3, 1994.
    (215) New and amended regulations for the following APCDs were 
submitted on February 24, 1995, by the Governor's designee.
    (i) Incorporation by reference.
    (A) South Coast Air Quality Management District.
    (1) Rules 1125 and 1126, adopted on January 13, 1995.
    (2) Rule 1153 adopted on January 13, 1995.
    (3) Rule 1106, adopted on January 13, 1995.
    (4) Rule 1164, adopted on January 13, 1995.
    (5) Rule 1124, adopted January 13, 1995.
    (B) Ventura County Air Pollution Control District.
    (1) Rule 74.12 adopted on January 10, 1995.
    (2) Rule 71 and Rule 71.5, adopted on December 13, 1994.
    (3) Rule 74.18 adopted December 13, 1994.
    (C) San Joaquin Valley Unified Air Pollution Control District.
    (1) Rule 4403, adopted on February 16, 1995.
    (D)  [Reserved]
    (1) Rule 2.26 adopted November 9, 1994.
    (216) New and amended regulations for the following APCDs were 
submitted on March 31, 1995, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Mojave Desert Air Quality Management District.
    (1) Rule 1116, adopted on February 22, 1995.
    (2) Rule 221, adopted December 21, 1994.
    (3) Rule 1159, adopted on February 22, 1995.
    (4) Rule 1114 adopted February 22, 1995.
    (B) Bay Area Air Quality Management District.
    (1) Amended Regulation 2, Rule 1, Section 129 adopted on February 1, 
1995; Amended Regulation 2, Rule 6, Sections 232, 234, 310, 311, 403, 
404, 420, 421, 422, 423 adopted on February 1, 1995.
    (217) New and amended regulations for the following APCDs were 
submitted on February 28, 1994, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Bay Area Air Quality Management District.
    (1) Amended Regulation 2, Rule 1, Sections 102, 129, 204, 213, 214, 
215, 216, 217, 218, 219, 302, 408, 411 adopted November 3, 1993; and New 
Regulation 2, Rule 6, Sections 206, 207, 210, 212, 213, 214, 218, 222, 
230, 231, 301, 311, 401, 402, 403, 404, 420, 421, 422, 602 adopted 
November 3, 1993.
    (B) Lake County Air Pollution Control District.
    (1) New Regulation 12, section 12.200 (a4), (c2), (d1), (d2), (d3), 
(e3), (f1), (f2), (m1), (o1), (p1), (p2), (s3), and sections 12.800-
12.850, adopted October 19, 1993.
    (218) New and amended regulations for the Bay Area Air Quality 
Management District were submitted on April 29, 1994 by the Governor's 
designee.
    (i) Incorporation by reference.
    (A) New Regulation 2, Rule 6, Sections 310 and 423 adopted November 
3, 1993.
    (219) New and amended regulations for the following APCDs were 
submitted on April 13, 1995, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Santa Barbara County Air Pollution Control District.
    (1) Rule 339, adopted December 15, 1994.
    (220) New and amended regulations for the following APCDs were 
submitted on May 24, 1995, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Santa Barbara County Air Pollution Control District.
    (1) Rule 323, adopted March 16, 1995.
    (B)(1) Rule 218, adopted on February 9, 1995.
    (2) Rule 236 adopted on February 9, 1995.
    (3) Rule 244, adopted on February 9, 1995.
    (C) South Coast Air Quality Management District.
    (1) Rule 1121, adopted on March 10, 1995.
    (221) New and amended regulations for the following APCDs were 
submitted on May 25, 1995 by the Governor's designee.
    (i) Incorporation by reference.

[[Page 148]]

    (A) Kern County Air Pollution Control District.
    (1) Rule 411 and Rule 413, adopted on April 6, 1995.
    (2) Rule 410.4, adopted on April 6, 1995.
    (3) Rule 425.2, adopted on April 6, 1995.
    (222) New and amended regulations for the following APCDs were 
submitted on June 16, 1995, by the Governor's designee.
    (i) Incorporation by reference.
    (A) South Coast Air Quality Management District.
    (1) Rules 1107, 1115, and 1171 adopted on May 12, 1995.
    (B) El Dorado County Air Pollution Control District.
    (1) Rule 234, adopted on April 25, 1995.
    (C) Sacramento Metropolitan Air Quality Management District.
    (1) Rule 411, adopted on February 2, 1995.
    (2) Rule 413, adopted on April 6, 1995.
    (3) Rule 412, adopted on June 1, 1995.
    (D) San Diego County Air Pollution Control District.
    (1) Rule 67.24, adopted on March 7, 1995.
    (223) Revised ozone transportation control measure (TCM) for the San 
Joaquin Valley submitted on March 2, 1995, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Railroad Grade Separations TCM, adopted on September 14, 1994.
    (224) New and amended regulations for the following APCDs were 
submitted on August 10, 1995, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Sacramento Metropolitan Air Quality Management District.
    (1) Rule 448 and rule 449, adopted on February 2, 1995.
    (B) Ventura County Air Pollution Control District.
    (1) Rule 70, adopted on May 9, 1995.
    (C) Mojave Desert Air Quality Management District.
    (1) Rules 1400, 1401, 1402, 1404. Adopted on June 28, 1995.
    (D) [Reserved]
    (E) Santa Barbara County Air Pollution Control District.
    (1) Amended Rule 370 adopted on June 15, 1995.
    (225) New and amended regulations for the following APCDs were 
submitted on October 13, 1995 by the Governor's designee.
    (i) Incorporation by reference.
    (A) South Coast Air Quality Management District.
    (1) Rules 1130 and 1136 adopted September 8, 1995.
    (2) Rule 462, revised on June 9, 1995.
    (B) Placer County Air Pollution Control District.
    (1) Rule 238, adopted June 8, 1995.
    (2) Rule 212, adopted on June 8, 1995.
    (3) Rule 239, revised June 8, 1995.
    (4) Rule 235, adopted on June 8, 1995.
    (5) Rule 216 adopted on June 8, 1995.
    (C)(1) Rules 236 and 237, adopted on July 25, 1995 and June 27, 
1995, respectively.
    (2) Rule 235 adopted on June 27, 1995.
    (D) San Joaquin Valley Unified Air Pollution Control District.
    (1) Rule 4602, adopted June 15, 1995.
    (E) Monterey Bay Unified Air Pollution Control District.
    (1) Rule 431, adopted on August 16, 1995.
    (226) Air Quality Management Plan for the following APCD was 
submitted on September 11, 1991, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Great Basin Unified Air Pollution Control District.
    (1) Air Quality Management Plan for the Mammoth Lakes PM-10 Planning 
Area adopted December 12, 1990.
    (227) New regulation for the following APCD was submitted on October 
18, 1995, by the Governor's designee.
    (i) Incorporation by reference.
    (A) San Joaquin Valley Unified Air Pollution Control District.
    (1) Rule 2530, adopted on June 15, 1995.
    (228) Air Quality Management Plans for the following APCD were 
submitted on January 9, 1992, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Great Basin Unified Air Pollution Control District.
    (1) Revisions to the Air Quality Management Plan for Mammoth Lakes 
PM-10 Planning Area adopted November 6, 1991.
    (i) Rule 431 adopted November 6, 1991.

[[Page 149]]

    (ii) Town of Mammoth Lakes Municipal Code Chapter 8.30 dated October 
2, 1991.
    (229) New and amended regulations for the following APCDs were 
submitted on January 31, 1996, by the Governor's designee.
    (i) Incorporation by reference.
    (A) South Coast Air Quality Management District.
    (1) Rule 461, adopted on September 8, 1995.
    (2) Rule 701, adopted on September 9, 1995.
    (230) New and amended regulations for the following APCDs were 
submitted on March 26, 1996, by the Governors designee.
    (i) Incorporation by reference.
    (A) Ventura County Air Pollution Control District.
    (1) Rule 74.7, adopted on October 10, 1995.
    (2) Rule 74.23, adopted on October 10, 1995.
     (B) South Coast Air Quality Management District.
    (1) Rule 1134, adopted on December 7, 1995.
    (2) Rule 102 amended on November 17, 1995.
    (C) Kern County Air Pollution Control District.
    (1) Rule 427, adopted on January 25, 1996.
    (231) New and amended regulations for the following APCDs were 
submitted on May 10, 1996, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Monterey Bay Unified APCD.
    (1) Rules 207 and 215, adopted on March 20, 1996.
    (B) Kern County Air Pollution Control District.
    (1) Rule 102 and Rule 410.3, adopted on March 7, 1996.
    (2) Rule 410.1, Rule 410.5, Rule 411, and Rule 414.5 amended on 
March 7, 1996.
    (232) New regulations for the following APCD were submitted on March 
21, 1994, by the Governor's designee:
    (i) Incorporation by reference.
    (A) South Coast Air Quality Management District.
    (1) Regulation XX, adopted October 15, 1993.
    (233) New and amended plans for the following agencies were 
submitted on December 29, 1994, by the Governor's designee.
    (i) Incorporation by reference.
    (A) South Coast Air Quality Management District.
    (1) 15% Rate-of-Progress plan and Post-1996 Rate-of-Progress plan 
for the Los Angeles-South Coast Air Basin Area, as contained in the 
``Rate-of-Progress Plan Revision: South Coast Air Basin & Antelope 
Valley & Coachella/San Jacinto Planning Area,'' adopted on December 9, 
1994.
    (B) Sacramento Metropolitan Air Quality Management District.
    (1) Emissions inventory, Post-1996 Rate-of-Progress plan, modeling, 
and ozone attainment demonstration, as contained in ``Sacramento Area 
Attainment and Rate-of-Progress Plans,'' adopted by Sacramento 
Metropolitan Air Quality Management District on December 1, 1994; by 
Feather River Air Quality Management District on December 12, 1994; by 
El Dorado County Air Pollution Control District on December 13, 1994; by 
Yolo-Solano Air Pollution Control District on December 14, 1994; and by 
Placer County Air Pollution Control District on December 20, 1994.
    (234) The California Vehicle Inspection and Maintenance Program was 
submitted on January 22, 1996, by the Governor's designee.
    (i) Incorporation by reference.
    (A) California Air Resources Board.
    (1) Motor Vehicle Inspection and Maintenance Program adopted on 
January 22, 1996.
    (i) Health and Safety Code: Division 26, Part 5 Sec. 39032.5; 
Chapter 5. Motor Vehicle Inspection Program, Article 1, Article 2, 
Article 3, Article 4, Article 5, Article 6, Article 7, Article 8, 
Article 9.
    (ii) Business and Professions Code, Chapter 20.3, Automotive Repair, 
Article 4, Sec. 9886, Sec. 9886.1, Sec. 9886.2, Sec. 9886.4.
    (iii) Vehicle Code Sec. 4000.1, Sec. 4000.2, Sec. 4000.3, 
Sec. 4000.6.
    (iv) Title 16, California Code or Regulations, Division 33, Bureau 
of Automotive Repair, Article 5.5, Motor Vehicle Inspection Program, 
Sec. 3340.1, Sec. 3340.5, Sec. 3340.6, Sec. 3340.10, Sec. 3340.15, 
Sec. 3340.16, Sec. 3340.16.5, Sec. 3340.16.6, Sec. 3340.17, 
Sec. 3340.18, Sec. 3340.22, Sec. 3340.22.1, Sec. 3340.22.2, 
Sec. 3340.22.3,

[[Page 150]]

Sec. 3340.23, Sec. 3340.24, Sec. 3340.28, Sec. 3340.29, Sec. 3340.30, 
Sec. 3340.31, Sec. 3340.32, Sec. 3340.32.1, Sec. 3340.33, 
Sec. 3340.33.1, Sec. 3340.35, Sec. 3340.35, Sec. 3340.36, Sec. 3340.41, 
Sec. 3340.41.3, Sec. 3340.41.5, Sec. 3340.42, Sec. 3340.42.1., 
Sec. 3340.50, Sec. 3340.50.1, Sec. 3340.50.3, Sec. 3340.50.4, 
Sec. 3340.50.5.
    (235) New and amended plans for the following agencies were 
submitted on May 17, 1996, by the Governor's designee.
    (i) Incorporation by reference.
    (A) California Air Resources Board.
    (1) Executive Order G-96-031, dated May 17, 1996, State commitment 
to participate in public consultative process, submit a revised 
attainment demonstration for the South Coast as appropriate by December 
31, 1997, and submit control measures to achieve emission reductions 
determined to be appropriate, if any, by December 31, 1999.
    (236) New and amended plans for the following agencies were 
submitted on June 13, 1996, by the Governor's designee.
    (i) Incorporation by reference.
    (A) California Air Resources Board.
    (1) Letter dated June 13, 1996, from James D. Boyd to David 
Howekamp, including ``Corrections to State and Local Measures'' 
(Attachment A) and ``Summary Emission Reduction Spreadsheets'' 
(Attachment C).
    (237) New and amended plans for the following agencies were 
submitted on July 10, 1996, by the Governor's designee.
    (i) Incorporation by reference.
    (A) South Coast Air Quality Management District.
    (1) Revised rule adoption schedule, adopted on April 12, 1996.
    (238) New and amended plans for the following agencies were 
submitted on July 12, 1996, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Ventura County Air Pollution Control District.
    (1) ``Revised Rule Adoption and Implementation Schedule'' (Table 4-
2) and ``Architectural Coatings'' (Appendix E-95, Tables E-43 and E-45) 
contained in ``Ventura County 1995 Air Quality Management Plan 
Revision,'' adopted on December 19, 1995.
    (B) San Joaquin Valley Unified Air Pollution Control District.
    (1) Post-1996 Rate-of-Progress plan, as contained in ``San Joaquin 
Valley Revised Post-1996 Rate-of-Progress Plans,'' adopted on September 
20, 1995.
    (239) New and amended regulations for the following APCDs were 
submitted on July 23, 1996, by the Governor's designee:
    (i) Incorporation by reference.
    (A) Mojave Desert Air Quality Management District.
    (1) Rules 1300-1306, adopted on March 25, 1996.
    (2) Rule 1115, adopted on March 2, 1992, and amended on April 22, 
1996.
    (B)-(C) [Reserved]
    (D)(1) Rule 2 amended on April 9, 1996.
    (E) Bay Area Air Quality Management District.
    (1) Rule 9-7 adopted on September 15, 1993, Rule 9-8 adopted on 
January 20, 1993, Rule 9-9 adopted on September 21, 1994, and Rule 9-12 
adopted on January 19, 1994.
    (2) Rule 8-4, Rule 8-11, Rule 8-12, Rule 8-13, Rule 8-14, Rule 8-19, 
Rule 8-20, Rule 8-23, Rule 8-29, Rule 8-31, Rule 8-32, Rule 8-38, Rule 
8-43, Rule 8-45, Rule 8-50 amended on December 20, 1995.
    (3) Rule 8-3, adopted on March 1, 1978, revised on December 20, 
1995.
    (240) New and amended regulations for the following APCD were 
submitted on August 28, 1996 by the Governor's designee.
    (i) Incorporation by reference.
    (A) South Coast Air Quality Management District.
    (1) Rules 212, 1301, 1302, 1309, 1309.1, 1310, and 1313, adopted on 
December 7, 1995, Rule 1303, adopted on May 10, 1996, and Rules 1304 and 
1306, adopted on June 14, 1996.
    (2) Rules 2000, 2001, 2002, 2004, 2006, 2007, 2011, 2011--Appendix 
A, 2012, 2012--Appendix A, and 2015 adopted on October 15, 1993 and 
amended on December 7, 1995.
    (3) Rule 2012(j)(3)--Testing Guidelines (Protocol) for Alternative 
Nitrogen Oxides Emission Rate Determination at Process Units, dated 
March 31, 1994, adopted on December 7, 1995.
    (4) Rule 2005 adopted on October 15, 1993 and amended on May 10, 
1996.
    (241) New and amended regulations for the following APCD were 
submitted

[[Page 151]]

on October 18, 1996 by the Governor's designee.
    (i) Incorporationed by reference.
    (A) San Diego County Air Pollution Control District.
    (1) Rules 2, Definitions; 67.0, Architectural Coatings; 67.1, 
Alternative Emission Control Plans; 67.2, Dry Cleaning Equipment Using 
Petroleum-Based Solvents; 67.3, Metal Parts and Products Coating 
Operations; 67.5, Paper, Film, and Fabric Coating Operations; 67.7, 
Cutback and Emulsified Asphalts; 67.12, Polyester Resin Operations; 
67.15, Pharmaceutical and Cosmetic Manufacturing Operations; 67.16, 
Graphic Arts Operations; 67.17, Storage of Materials Containing Volatile 
Organic Compounds; 67.18, Marine Coating Operations; and 67.24, Bakery 
Ovens, adopted on May 15, 1996.
    (2) Rule 67.4, revised on May 15, 1996.
    (B) Yolo-Solano Air Quality Management District.
    (1) Rule 2.27, revised on August 14, 1996.
    (243) Transportation Air Quality Conformity Procedures and 
Transportation Conformity Consultation Procedures for the following AQMD 
were submitted on December 16, 1996, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Bay Area Air Quality Management District.
    (1) ``The San Francisco Bay Area Transportation Air Quality 
Conformity Procedures,'' which includes sections 93.100-93.104 and 
sections 93.106-93.136, adopted on November 6, 1996.
    (2) ``The San Francisco Bay Area Transportation Air Quality 
Conformity Interagency Consultation Procedures,'' adopted on November 6, 
1996.
    (244) New and amended regulations for the following APCDs were 
submitted on March 3, 1997, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Monterey Bay Unified Air Pollution Control District.
    (1) Rule 101 revised on November 13, 1996.
    (B) San Diego County Air Pollution Control District.
    (1) Amended Rule 10, adopted July 25, 1995.
    (245) New and amended regulations for the following APCDs were 
submitted on March 26, 1997, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Yolo-Solano Air Quality Management District.
    (1) Rule 3.4, adopted on December 11, 1996.
    (B) San Diego County Air Pollution Control District.
    (1) Amended Rule 21, adopted November 29, 1994.
    (246) New and amended regulations for the following APCDs were 
submitted on October 28, 1996, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Northern Sierra Air Quality Management District.
    (1) Rules 101, 202, 203, 204, 206, 207, 208, 209, 210, 221, 222, 
223, 225, 300, 301, 314, 315, and 317, adopted on September 11, 1991, 
Rule 102 adopted on May 11, 1994, Rule 313 adopted on June 10, 1992, and 
Rule 316 adopted on August 14, 1996.
    (247) New and amended plans for the following agency were submitted 
on February 5, 1997, by the Governor's designee.
    (i) Incorporation by reference.
    (A) South Coast Air Quality Management District.
    (1) Carbon monoxide emissions inventory, VMT forecasts and 
commitments to monitor actual VMT levels and revise and replace the VMT 
projections as needed in the future, as contained in the South Coast 
1997 Air Quality Management Plan.
    (248) New and amended regulations for the following APCDs were 
submitted on August 1, 1997, by the Governor's designee.
    (i) Incorporation by reference.
    (A) San Diego County Air Pollution Control District
    (1) Rule 67.10 adopted on June 25, 1997.
    (249) [Reserved]
    (250) New regulations for the following APCD were submitted on 
October 31, 1997, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Santa Barbara County Air Pollution Control District.
    (1) Rule 1301 adopted on September 18, 1997.
    (251) New and amended plans for the following agency were submitted 
on

[[Page 152]]

November 5, 1997, by the Governor's designee.
    (i) Incorporation by reference.
    (A) Ventura County Air Pollution Control District.
    (1) Commitments to adopt and implement control measures contained in 
the Ventura 1997 Air Quality Management Plan, adopted on October 21, 
1997.
    (252) Air Quality Management Plan for the following APCD was 
submitted on December 28, 1992, by the Governor's designee.
    (i) Incorporation by reference. (A) San Joaquin Valley Unified Air 
Pollution Control District.
    (1) Federal 1992 Air Quality Attainment Plan for Carbon Monoxide and 
Appendices adopted on November 18, 1992.
    (253) Carbon Monoxide Redesignation Request and Maintenance Plan for 
ten federal planning areas submitted on July 3, 1996, by the Governor's 
designee.
    (i) Incorporation by reference.
    (A) California Air Resources Board. (1) Carbon Monoxide 
Redesignation Request and Maintenance Plan for the following areas: 
Bakersfield Metropolitan Area, Chico Urbanized Area, Fresno Urbanized 
Area, Lake Tahoe North Shore, Lake Tahoe South Shore, Modesto Urbanized 
Area, Sacramento Area, San Diego Area, San Francisco-Oakland-San Jose 
Area, and Stockton Urbanized Area adopted on April 26, 1996.
    (254) New and amended regulations for the follwoign APCDs were 
submitted on March 10, 1998, by the Governor's designee.
    (i) Incorporation by reference.
    (A) San Joaquin Valley Unified Air Pollution Control District
    1) Rule 4401 adopted on January 15, 1998.
[37 FR 10850, May 31, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.220, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.

    Effective Date Notes:  1. At 63 FR 32623, June 15, 1998, Sec. 52.220 
was amended by adding paragraphs (c)(240(i)(A) (2), (3), and (4), 
effective July 15, 1998.
    2. At 63 FR 33855, June 22, 1998, Sec. 52.220 was amended by adding 
paragraphs (c)(248) and (c)(254), effective July 22, 1998.



Sec. 52.221  Classification of regions.

    The California plan was evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                               Pollutant
                                                      ----------------------------------------------------------
              Air quality control region                                                           Photochemical
                                                       Particulate   Sulfur   Nitrogen   Carbon      oxidants
                                                          matter     oxides    dioxide  monoxide  (hydrocarbons)
----------------------------------------------------------------------------------------------------------------
North Coast Intrastate...............................          II        III       III       III           III
San Francisco Bay Area Intrastate....................          II         II       III         I             I
North Central Coast Intrastate.......................          II        III       III       III             I
South Central Coast Intrastate.......................         III        III       III       III           III
Metropolitan Los Angeles Intrastate..................           I         II         I         I             I
Northeast Plateau Intrastate.........................         III        III       III       III           III
Sacramento Valley Intrastate.........................          II        III       III         I             I
San Joaquin Valley Intrastate........................           I        III       III         I             I
Great Basin Valley Intrastate........................         III        III       III       III           III
Southeast Desert Intrastate..........................           I        III       III       III             I
San Diego Intrastate.................................          II        III       III         I             I
Lake County Intrastate...............................          II        III       III       III           III
Lake Tahoe Intrastate................................          II        III       III         I             I
Mountain Counties Intrastate.........................          II        III       III         I             I
----------------------------------------------------------------------------------------------------------------

[37 FR 10850, May 31, 1972, as amended at 39 FR 16346, May 8, 1974; 46 
FR 3884, Jan. 16, 1981]



Sec. 52.222  Negative declarations.

    (a) The following air pollution control districts submitted negative 
declarations for volatile organic compound source categories to satisfy 
the requirements of section 182 of the Clean Air Act, as amended. The 
following negative declarations are approved as additional information 
to the State Implementation Plan.

[[Page 153]]

    (1) Mojave Desert Air Quality Management District.
    (i) Natural Gas and Gasoline Processing Equipment and Chemical 
Processing and Manufacturing were submitted on July 13, 1994 and adopted 
on May 25, 1994.
    (ii) Asphalt Air Blowing was submitted on December 20, 1994 and 
adopted on October 26, 1994.
    (iii) Vacuum Producing Devices or Systems was submitted on December 
29, 1994 and adopted on December 21, 1994.
    (iv) Synthetic Organic Chemical Manufacturing Industry (SOCMI) 
Distillation, SOCMI Reactors, SOCMI Batch Processing, Offset 
Lithography, Industrial Wastewater, Plastic Parts Coating (Business 
Machines), Plastic Parts (Other), and Ship Building were submitted on 
August 7, 1995 and adopted on June 28, 1995.
    (2) Sacramento Metropolitan Air Quality Management District.
    (i) Plastic Parts Coating: Business Machines and Plastic Parts 
Coating: Other were submitted on June 6, 1996 and adopted on May 2, 
1996.
    (3) Santa Barbara County Air Pollution Control District.
    (i) Industrial Wastewater, Plastic Parts Coating: Business Machines, 
Plastic Parts Coating: Other, Industrial Cleaning Solvents, Offset 
Lithography, and Shipbuilding Coatings were submitted on July 12, 1996 
and adopted on May 16, 1996.
    (b) The following air pollution control districts submitted negative 
declarations for oxides of nitrogen source categories to satisfy the 
requirements of section 182 of the Clean Air Act, as amended. The 
following negative declarations are approved as additional information 
to the State Implementation Plan.
    (1) Sacramento Metropolitan Air Quality Management District.
    (i) Nitric and Adipic Acid Manufacturing Plants, Utility Boilers, 
Cement Manufacturing Plants, Glass Manufacturing Plants, and Iron and 
Steel Manufacturing Plants were submitted on March 4, 1996, and adopted 
on August 3, 1995.
    (2) San Joaquin Valley Unified Air Pollution Control District.
    (i) Nitric and Adipic Acid Manufacturing Plants, Cement 
Manufacturing Plants, Asphalt Batch Plants, Iron and Steel Manufacturing 
Plants, and Driers were submitted on October 17, 1994 and adopted on 
September 14, 1994.
[60 FR 47076, Sept. 11, 1995 as amended at 61 FR 56474, 56476, Nov. 1, 
1996; 62 FR 40937, July 31, 1997; 62 FR 43647, Aug. 15, 1997]



Sec. 52.223  Approval status.

    (a) With the exceptions set forth in this subpart, the Administrator 
approves California's plan for the attainment and maintenance of the 
national standards under section 110 of the Clean Air Act.
    (b) With the exceptions set forth in this subpart, the Administrator 
approves the plan with respect to Part D, Title I of the Clean Air Act, 
as amended in 1977, for the nonattainment areas listed in this 
paragraph. In addition, continued satisfaction of the requirements of 
Part D for the ozone portion of the State Implementation Plan (SIP) 
depends on the adoption and submittal of reasonably available control 
technology (RACT) requirements by July 1, 1980, for sources covered by 
Control Technique Guidelines (CTGs) issued between January 1978 and 
January 1979 and adoption and submittal by each subsequent January of 
additional RACT requirements for sources covered by CTGs issued by the 
previous January.
    (1) Imperial County for O3.
    (2) North Central Coast Air Basin for O3.
    (3) South Coast Air Basin for O3, CO, NO2, and 
PM.
    (4) San Diego Air Basin for O3, CO, and TSP.
    (5) San Joaquin Valley Air Basin.
    (i) Kern County nonattainment area for ozone, CO, SO2, 
and PM.
    (ii) Kings County for O3 and TSP.
    (iii) Madera County for O3 and TSP.
    (iv) Merced County for O3 and TSP.
    (v) San Joaquin County for CO, O3 and TSP.
    (vi) Stanislaus County for CO, O3 and TSP.
    (vii) Tulare County for O3 and TSP.
    (viii) Fresno County for O3, CO, and TSP.
    (6) South Central Coast Air Basin.

[[Page 154]]

    (i) Santa Barbara County nonattainment area for O3, CO 
and TSP.
    (ii) Ventura County for O3, CO and TSP.
    (7) Sacramento Valley Air Basin.
    (i) Butte County for O3 and CO.
    (ii) Sutter County for O3.
    (iii) Yuba County for O3.
    (iv) Sacramento AQMA for O3.
    (v) Sacramento County Metropolitan Area for CO.
    (8) Southeast Desert Air Basin.
    (i) Los Angeles County for Ozone.
    (ii) San Bernardino County for Ozone.
    (iii) Riverside County for Ozone.
    (9) San Francisco Bay Area Air Basin for O3, CO and TSP.
    (10) Mountain Counties Air Basin.
    (i) El Dorado County (Mountain Counties Air Basin portion) for 
O3.
    (ii) Placer County (Mid-County portion) for O3.
    (c) [Reserved]
    (d) With the exceptions set forth in this subpart, the Administrator 
approves the plan with respect to Part D, Title I of the Clean Air Act, 
as amended in 1977, for the nonattainment areas listed in this 
paragraph.
    (1) Lake Tahoe Basin for CO.
    (2) EPA approves the CO plan for the Lake Tahoe Basin as meeting the 
requirements of Part D. This approval includes the resolution of the 
Lake Tahoe Regional Planning Agency banning new source construction 
pending the adoption of a new regional plan and ordinances. However, EPA 
disapproves the plan for any future time during which the Tahoe Regional 
Planning Agency may remove its construction ban prior to EPA approval of 
the new regional plan and ordinances.
[45 FR 74484, Nov. 11, 1980]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.223, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.224  General requirements.

    (a) The requirements of Sec. 51.116(c) of this chapter are not met 
except in certain Air Pollution Control Districts (APCD) as indicated in 
this paragraph since the plan does not provide procedures by which 
emission data, as correlated with applicable emission limitations, will 
be made available to the public.
    (1) The following APCD's meet the requirements of Sec. 51.116(c) of 
this chapter:
    (i) Siskiyou County APCD.
    (ii) San Diego County APCD.
    (iii) Great Basin Unified APCD.
    (iv) Del Norte County APCD.
    (v) Humboldt County APCD.
    (vi) Mendocino County APCD.
    (vii) Northern Sonoma County APCD.
    (viii) Trinity County APCD.
    (ix) Amador County APCD.
    (2) The following APCD's do not provide for the correlation of 
emission data with applicable emission limitations as required by 
Sec. 51.116(c) of this chapter. In these APCD's, only the requirements 
of Sec. 52.224(b)(4) are in effect:
    (i) Merced County APCD.
    (ii) Stanislaus County APCD.
    (iii) Fresno County APCD.
    (iv) Calaveras County APCD.
    (v) Tuolumne County APCD.
    (vi) San Joaquin County APCD.
    (vii) Mariposa County APCD.
    (viii) Tulare County APCD.
    (ix) Kern County APCD.
    (x) Madera County APCD.
    (xi) Yolo-Solano APCD.
    (xii) Sutter County APCD.
    (xiii) Glenn County APCD.
    (xiv) Tehama County APCD.
    (xv) Sierra County APCD.
    (xvi) Shasta County APCD.
    (xvii) Sacramento County APCD.
    (xviii)-(xix) [Reserved]
    (xx) Lake County APCD.
    (xxi) Imperial County APCD.
    (xxii) [Reserved]
    (xxiii) Ventura County APCD.
    (xxiv) Monterey Bay Unified APCD.
    (xxv) [Reserved]
    (xxvi) San Luis Obispo County APCD.
    (xxvii) Kings County APCD.
    (xxviii) Plumas County APCD.
    (xxix) Nevada County APCD.
    (b) Regulation for public availability of emission data. (1) Any 
person who cannot obtain emission data from the Agency responsible for 
making emission data available to the public, as specified in the 
applicable plan, except for those APCD's specified in paragraph (a) of 
this section, concerning emissions from any source subject to emission 
limitations which are part of the approved plan may request that the 
appropriate Regional Administrator obtain and make public such data.

[[Page 155]]

Within 30 days after receipt of any such written request, the Regional 
Administrator shall require the owner or operator of any such source to 
submit information within 30 days on the nature and amounts of emissions 
from such source and any other information as may be deemed necessary by 
the Regional Administrator to determine whether such source is in 
compliance with applicable emission limitations or other control 
measures that are part of the applicable plan.
    (2) Commencing after the initial notification by the Regional 
Administrator pursuant to paragraph (b)(1) of this section, the owner or 
operator of the source shall maintain records of the nature and amounts 
of emissions from such source and any other information as may be deemed 
necessary by the Regional Administrator to determine whether such source 
is in compliance with applicable emission limitations or other control 
measures that are part of the plan. The information recorded shall be 
summarized and reported to the Regional Administrator, on forms 
furnished by the Regional Administrator, and shall be submitted within 
45 days after the end of the reporting period. Reporting periods are 
January 1 to June 30 and July 1 to December 31.
    (3) Information recorded by the owner or operator and copies of this 
summarizing report submitted to the Regional Administrator shall be 
retained by the owner or operator for 2 years after the date on which 
the pertinent report is submitted.
    (4) Emission data obtained from owners or operators of stationary 
sources will be correlated with applicable emission limitations and 
other control measures that are part of the applicable plan and will be 
available at the appropriate regional office and at other locations in 
the state designated by the Regional Administrator.
    (c) The deletion of the following rules or portions of rules is 
disapproved, since these regulations are necessary to fulfill the 
requirements of 40 CFR 51.116(c).
    (1) Northcoast intrastate region:
    (i) Lake County APCD.
    (A) Section 49a, Public Records, and Section 49b, Record, of Part 
III, Definitions; and Part II, Authorization and Disclosure, submitted 
on October 23, 1974 and previously approved under 40 CFR 52.223, are 
retained.
[40 FR 55328, Nov. 28, 1975]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.224, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.225  Legal authority.

    (a) The requirements of Sec. 51.230(c) of this chapter are not met 
since the State Emergency Services Act does not apply to air pollution 
emergencies in a manner comparable to section 303 of the Clean Air Act, 
as amended.
    (b) The requirements of Sec. 51.230(f) of this chapter are not met 
since authority to make emission data available to the public 
inadequate. Such release is precluded under certain circumstances.
[37 FR 10852, May 31, 1972, as amended at 51 FR 40676, Nov. 7, 1986]



Sec. 52.226  Control strategy and regulations: Particulate matter, San Joaquin Valley and Mountain Counties Intrastate Regions.

    (a) [Reserved]
    (b) The following regulatory changes represent a relaxation of 
previously submitted regulations and an adequate control strategy has 
not been submitted showing that the relaxation will not interfere with 
attainment and maintenance of the National Ambient Air Quality Standards 
for particulate matter:
    (1) Kings County APCD.
    (i) Rule 405, Process Weight, submitted on July 25, 1973 is 
disapproved; and Rule 405, submitted on June 30, 1972, and previously 
approved in 40 CFR 52.223 is retained.
    (ii) Rule 407.1, Disposal of Solid and Liquid Wastes, submitted on 
November 4, 1977, is disapproved; and Rule 407.1, Disposal of Solid and 
Liquid Wastes, submitted on June 30, 1972, and previously approved under 
40 CFR 52.223 is retained.
    (2) Calaveras County APCD.
    (i) The revocation of Rule 407(b), Combustion Contaminants, is 
disapproved; and Rule 407(b), submitted on June 30, 1972, and previously 
approved in 40 CFR 52.223 is retained.

[[Page 156]]

    (ii) The revocation of Rule 408, Fuel Burning Equipment, is 
disapproved; and Rule 408, submitted on June 30, 1972, and previously 
approved in 40 CFR 52.223 is retained.
    (iii) The addition of Rule 209, Fossil Fuel-Steam Generator 
Facility, is disapproved; and Rule 408, submitted on June 30, 1972 and 
previously approved in 40 CFR 52.223 is retained.
    (3) Tuolumne County APCD.
    (i) Rule 207, Particulate Matter, submitted on July 22, 1975, is 
disapproved; and Rules 404 and 407(b), submitted on June 30, 1972 and 
previously approved in 40 CFR 52.223 are retained.
    (ii) Rule 209, Fossil Fuel-Steam Generator Facility, submitted on 
July 22, 1975, is disapproved; and Rule 408, submitted on June 30, 1972, 
and previously approved in 40 CFR 52.223 is retained.
    (iii) Rule 207, Particulate Matter, submitted on February 10, 1977, 
is disapproved and the previously approved Rules 404 and 407(b), 
submitted on June 30, 1972, remain in effect.
    (iv) Rule 209, Fossil Fuel-Steam Generator Facility, submitted on 
February 10, 1977, is disapproved and the previously approved Rule 408, 
submitted on June 30, 1972, remains in effect.
    (4) Fresno County APCD.
    (i) Rule 407, Disposal of Solid or Liquid Wastes, submitted on 
February 10, 1976, is disapproved; and Rule 407.1, submitted on June 30, 
1972, and previously approved in 40 CFR 52.223 is retained.
    (ii) Rule 407, Disposal of Solid or Liquid Wastes, submitted on 
November 10, 1976, is disapproved; and Rule 407.1, submitted on June 30, 
1972 and previously approved in 40 CFR 52.223 is retained.
    (5) San Joaquin County APCD.
    (i) Rule 407.1, Disposal of Solid or Liquid Wastes, submitted on 
February 10, 1976, is disapproved; and Rule 407.1, submitted on June 30, 
1972 and previously approved in 40 CFR 52.223 is retained.
    (6) Mariposa County APCD.
    (i) Rule 209, Fossil Fuel-Steam Generator Facility, submitted on 
January 10, 1975, is disapproved; and Rule 6.4, submitted on June 30, 
1972 and previously approved in 40 CFR 52.223 is retained.
    (7) Kern County APCD.
    (i) Rule 407.1, Disposal of Solid or Liquid Wastes, submitted on 
July 22, 1975, is disapproved; and Rule 407.1, submitted on June 30, 
1972 and previously approved in 40 CFR 52.223 is retained.
    (8) Madera County APCD.
    (i) Rule 405, Process Weight, submitted on January 10, 1975 is 
disapproved; and Rule 405, submitted on June 30, 1972 and previously 
approved in 40 CFR 52.223 is retained.
    (9) Tulare County APCD.
    (i) Paragraph b. of Rule 407.1.
    (10) Merced County APCD.
    (i) Rule 407.1, Disposal of Solid or Liquid Wastes, submitted on 
August 2, 1976 is disapproved; and Rule 407.1 submitted on June 30, 1972 
and previously approved in 40 CFR 52.223 is retained.
[37 FR 10850, May 31, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.226, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.227  Control strategy and regulations: Particulate matter, Metropolitan Los Angeles Intrastate Region.

    (a) The requirements of Subpart G of this chapter are not met since 
the plan does not provide for attainment and maintenance of the 
secondary standards for particulate matter in the Metropolitan Los 
Angeles Intrastate Region.
    (b) The following regulations are disapproved since they are not 
part of the approved control strategy and do not provide for the degree 
of control needed for the attainment and maintenance of the primary 
standards for particulate matter in the Metropolitan Los Angeles 
Intrastate Region.
    (1) Los Angeles County Air Pollution Control District:
    (i) Regulation IV, Rule 68.1.
    (2) Riverside County Air Pollution Control District:
    (i) Regulation IV, Rule 54 for process sources with a process weight 
rate in excess of 62,000 lbs. per hour. Rule 54 is approved for process 
sources with a process weight of 62,000 lbs. per hour or less.
    (3) Southern California APCD:
    (i) Regulation IV, Rule 404 Particulate Matter--Concentration, 
submitted on August 2, 1976.
    (ii) Regulation IV, Rule 473 Disposal of Solid and Liquid Wastes, 
submitted on August 2, 1976.

[[Page 157]]

    (4) South Coast AQMD.
    (i) Rule 401(b) submitted on August 15, 1980.
    (c) The rescission by the Southern California APCD of the following 
rules, which were previously approved in the May 31, 1972 (37 FR 10850) 
and September 22, 1972 (37 FR 19813) Federal Register issues, is 
disapproved since adequate replacementrules have not been submitted and 
no analysis has been presented to show that this rescission will not 
interfere with the attainment and maintenance of the NAAQS for 
particulate matter as required by section 110 of the Clean Air Act. In 
addition, the following rules, as submitted in June 1972 and approved 
for the SIP, remain federally enforceable:
    (1) Los Angeles County APCD.
    (i) Regulation IV, Rule 52 Particulate Matter--Concentration.
    (ii) Regulation IV, Rule 58 Disposal of Solid and Liquid Wastes.
    (2) San Bernardino County APCD.
    (i) Regulation IV, Rule 52A Particulate Matter--Concentration.
    (ii) Regulation IV, Rule 58A Disposal of Solid and Liquid Wastes.
    (3) Riverside County APCD.
    (i) Regulation IV, Rule 52 Particulate Matter--Concentration.
    (ii) Regulation IV, Rule 58 Disposal of Solid and Liquid Wastes.
    (4) Orange County APCD.
    (i) Regulation IV, Rule 52 Particulate Matter--Concentration.
    (ii) Regulation IV, Rule 58 Disposal of Solid and Liquid Wastes.
[37 FR 10850, May 31, 1972, as amended at 37 FR 19813, Sept. 22, 1972; 
43 FR 25687, June 14, 1978; 49 FR 18824, May 3, 1984; 51 FR 40676, Nov. 
7, 1986]



Sec. 52.228  Regulations: Particulate matter, Southeast Desert Intrastate Region.

    (a) The following regulations are disapproved since they are not 
part of the approved control strategy and do not provide for the degree 
of control needed for the attainment and maintenance of the national 
standards for particulate matter in the Southeast Desert Intrastate 
Region.
    (1) Imperial County Air Pollution Control District:
    (i) Rule 114A.
    (ii) Rule 116B.
    (2) Los Angeles County Air Pollution Control District:
    (i) Regulation IV, Rule 68.1.
    (3) Riverside County Air Pollution Control District:
    (i) Regulation IV, Rule 54 for process sources with a process weight 
rate in excess of 160,000 lbs. per hour. Rule 54 is approved for process 
sources with a process weight of 160,000 lbs. per hour or less.
    (b) The following regulatory changes represent a relaxation of 
previously submitted regulations, and an adequate control strategy has 
not been submitted showing that the relaxation will not interfere with 
the attainment and maintenance of the national ambient air quality 
standards for particulate matter:
    (1) Southeast Desert Intrastate Region:
    (i) Imperial County APCD.
    (A) Rule 406, Disposal of Solid and Liquid Wastes submitted on 
November 4, 1977 is disapproved; and Rule 116 C, Specific Contaminants 
submitted on June 30, 1972 and previously approved under 40 CFR 52.223 
is retained.
    (ii) Los Angeles County Air Pollution Control District.
    (A) Regulation IV, Rule 404 Particulate Matter-Concentration, and 
Rule 473, Disposal of Solid and Liquid Wastes, submitted on June 6, 1977 
are disapproved. Rules 52 and 58, titled as above, respectively, and 
submitted on June 30, 1972 and previouslyapproved under 40 CFR 52.223 
are retained.
    (iii) Riverside County Air Pollution Control District.
    (A) Regulation IV, Rules 404 Particulate Matter-Concentration, 405 
Particulate Matter-Weight, and Rule 473, Disposal of Solid and Liquid 
Wastes, submitted on June 6, 1977 are disapproved. Rules 52, Particulate 
Matter-Weight, 54, Dust and Fumes, and 58, Disposal of Solid and Liquid 
Wastes, submitted in 1972 and approved under 40 CFR 52.223, are 
retained.
    (iv) The repeal of San Bernardino County APCD Regulation VI, Orchard 
or Citrus Grove Heaters, submitted on June 6, 1977, is disapproved. This 
regulation (comprised of Rules 101 to 104, 109, 110, 120, and 130 to 
137), submitted on February 21, 1972 and approved

[[Page 158]]

under 40 CFR 52.223, is retained as part of the SIP.
[37 FR 10850, May 31, 1972, as amended at 37 FR 19813, Sept. 22, 1972; 
43 FR 35695, Aug. 11, 1978; 43 FR 40014, Sept. 8, 1978]



Sec. 52.229  Control strategy and regulations: Photochemical oxidants (hydrocarbons), Metropolitan Los Angeles Intrastate Region.

    (a) [Reserved]
    (b) The following rules are disapproved because they would result in 
a relaxation of control requirements contained in the presently approved 
State Implementation Plan, and no analysis has been presented to show 
that this relaxation will not interfere with the attainment and 
maintenance of NAAQS for photochemical oxidants (hydrocarbons) as 
required by section 110 of the Clean Air Act.
    (1) Southern California APCD.
    (i) Regulation IV, Rule 465 Vacuum Producing Devices or Systems, 
submitted on August 2, 1976.
    (2) South Coast Air Quality Management District.
    (i) Regulation IV, Rule 461 Gasoline Transfer and Dispensing, 
submitted on June 6, 1977. The version of this rule by the same number 
and title submitted on April 21, 1976 and approved under 40 CFR 52.223 
is retained.
    (ii) Rule 1115, Automotive Coatings, adopted on March 16, 1984 by 
the District and submitted by the state to EPA on July 10, 1984.
    (iii) Rule 1113, Architectural Coatings, adopted on August 2, 1985 
and submitted to EPA on November 12, 1985. The version of this rule by 
the same number and title submitted on July 10, 1984 and approved by EPA 
on January 24, 1985 is retained.
    (c) The rescission by the Southern California APCD of the following 
rules, which were previously approved in the September 22, 1972 (37 FR 
19813) Federal Register issue, is disapproved since adequate replacement 
rules have not been submitted anderfere with the attainment and 
maintenance of the NAAQS for photochemical oxidants (hydrocarbons) as 
required by section 110 of the Clean Air Act. In addition, the following 
rules, as submitted in June 1972 and approved for the SIP, remain 
federally enforceable:
    (1) Los Angeles County APCD, Regulation IV, Rule 69, Vacuum 
Producing Devices or Systems.
    (2) San Bernardino County APCD, Regulation IV, Rule 69, Vacuum 
Producing Devices or Systems.
    (3) Riverside County APCD, Regulation IV, Rule 74, Vacuum Producing 
Devices or Systems.
    (4) Orange County APCD, Regulation IV, Rule 69, Vacuum Producing 
Devices or Systems.
[37 FR 10850, May 31, 1972, as amended at 43 FR 25687, June 14, 1978; 43 
FR 40014, Sept. 8, 1978; 46 FR 5978, Jan. 21, 1981; 54 FR 5237, Feb. 2, 
1989; 54 FR 34515, Aug. 21, 1989]



Sec. 52.230  Control strategy and regulations: Nitrogen dioxide.

    (a) The requirements of Sec. 52.14(c)(3) of this chapter as of 
September 22, 1972 (47 FR 1983), are not met since the plan does not 
provide for the degree of nitrogen oxides emission reduction attainable 
through application of reasonably available control technology in the 
Metropolitan Los Angeles Intrastate Region. Therefore, Rule 68.b of the 
Orange County Air Pollution Control District is disapproved.
    (b) The following rules are disapproved since they are not part of 
the approved control strategy and do not provide for the degree of 
control necessary for the attainment and maintenance of NAAQS for 
nitrogen dioxide in the Metropolitan Los Angeles Intrastate AQCR:
    (1) Orange County APCD, Regulation IV, Rule 474, Fuel Burning 
Equipment--Oxides of Nitrogen, submitted on February 10, 1977.
    (c) The rescission by the Southern California APCD of the following 
rules is disapproved since adequate replacement rules have not been 
submitted and no analysis has been presented to show that this 
rescission will not interfere with the attainment and maintenance of the 
National Ambient Air Quality Standards as required by section 110 of the 
Clean Air Act. In addition, the following rules, as submitted in June 
1972 and approved for the SIP, remain federally enforceable:
    (1) Orange County APCD, Regulation IV, Rule 68, Fuel Burning 
Equipment--NOx.

[[Page 159]]

    (2) Orange County APCD, Regulation IV, Rule 67.1, Fuel Burning 
Equipment.
[43 FR 25687, June 14, 1978, as amended at 46 FR 3884, Jan. 16, 1981; 51 
FR 40677, Nov. 7, 1986]



Sec. 52.231  Regulations: Sulfur oxides.

    (a) [Reserved]
    (b) The deletion of the following rules or portions of rules is 
disapproved, since an adequate control strategy demonstration has not 
been submitted indicating that the deletions of the control requirements 
contained in those rules would not interfere with the attainment or 
maintenance of the National Ambient Air Quality Standard for Sulfur 
Oxides.
    (1) Lake County Intrastate Region.
    (i) Lake County, APCD.
    (A) Section 3(F), Sulfur of Part V, Prohibitions and Standards, 
submitted on October 23, 1974 and previously approved under 40 CFR 
52.223, is retained as applicable to sources other than sulfur recovery 
units.
[43 FR 34464, 34466, Aug. 4, 1978, as amended at 46 FR 3884, Jan. 16, 
1981; 46 FR 42461, Aug. 21, 1981]



Sec. 52.232  Part D conditional approval.

    (a) The following portions of the California SIP contain 
deficiencies with respect to Part D of the Clean Air Act which must be 
corrected by meeting the indicated conditions of Part D plan approval.
    (1) Imperial County for ozone.
    (i) By May 7, 1981, the NSR rules must be revised and submitted as 
an SIP revision. The rules must satisfy section 173 and 40 CFR Subpart 
I, ``Review of new sources and modifications.''

In revising the Imperial County APCD's NSR rules, the State/APCD must 
address (A) any new requirements in EPA's amended regulations for NSR 
under section 173 of the Clean Air Act (August 7, 1980, 45 FR 52676) 
which the APCD rules do not now satisfy and (B) those deficiencies cited 
in EPA's Evaluation Report Addendum (contained in Document File NAP-CA-
06 at the EPA Library in Washington, DC and the Region IX office).
    (ii) By January 1, 1981, a cutback asphalt rule which reflects 
reasonably available control technology (RACT) must be submitted as an 
SIP revision.
    (2) North Central Coast Air Basin for ozone.
    (i) By May 7, 1981, the NSR rules must be revised and submitted as 
an SIP revision. The rules must satisfy section 173 and 40 CFR 51.18, 
``Review of new sources and modifications.'' In revising the Monterey 
Bay Unified APCD's NSR rules, the State/APCD must address (a) any new 
requirements in EPA's amended regulations for NSR under section 173 of 
the Clean Air Act (August 7, 1980, 45 FR 52676) which the APCD rules do 
not now satisfy and (b) those deficiencies with respect to the September 
5, 1979 notice cited in EPA's Evaluation Report Addendum (contained in 
Document File NAP-CA-14 at the EPA Library in Washington, DC and the 
Region IX office).
    (ii) By March 4, 1981, one of the following must be submitted as an 
SIP revision: (a) Adequate justification that the cutback asphalt rule 
represents RACT, (b) amendment of the cutback asphalt rule to conform 
with the controls recommended in the CTG document for cutback asphalt, 
or (c) adequate documentation that the cutback asphalt rule will result 
in emission reductions which are within 5 percent of the reductions 
achievable with the controls recommended in the cutback asphalt CTG 
document.
    (3) South Coast Air Basin.
    (i)(A) By May 7, 1981, the NSR rules must be revised and submitted 
as an SIP revision. The rules must satisfy section 173 of the Clean Air 
Act and 40 CFR 51.18, ``Review of new sources and modifications.'' In 
revising the South Coast AQMD's NSR rules, the State/AQMD must address 
(1) any new requirements in EPA's amended regulations for NSR (45 FR 
31307, May 13, 1980 and 45 FR 52676, August 7, 1980) which the AQMD 
rules do not currently satisfy and (2) those deficiencies cited in EPA's 
Evaluation Report Addendum which still apply despite EPA's new NSR 
requirements (contained in Document File NAP-CA-9 at the EPA Library in 
Washington, DC and the Regional Office).
    (4) San Diego Air Basin.
    (i) For ozone, CO, TSP, and NO2:

[[Page 160]]

    (A) By May 7, 1981, the NSR rules submitted on March 17, 1980 
must be revised and submitted as an SIP revision. In revising the NSR 
rules, the State/APCD must address (1) any new requirements in EPA's 
amended regulations for NSR under section 173 of the Clean Air Act (May 
13, 1980, 45 FR 31307; and August 7, 1980, 45 FR 52676) which the APCD 
rules do not currently satisfy and (2) the deficiencies cited in EPA's 
Evaluation Report Addendum which still apply despite EPA's new NSR 
requirements. The Evaluation Report Addendum is contained in document 
file NAP-CA-19 and available at the EPA Region IX Office and the EPA 
Library in Washington, DC
    (5) The Kern County APCD.
    (i) For ozone, CO, and PM:
    (A) By November 19, 1981, the NSR rules must be revised and 
submitted as an SIP revision. The rules must satisfy section 173 of the 
Clean Air Act and 40 CFR Subpart I, ``Review of new sources and 
modification.'' In revising Kern County's NSR rules, the State/APCD must 
address all the requirements in EPA's amended regulations for NSR (45 FR 
31307, May 13, 1980 and 45 FR 52676, August 7, 1980) which the APCD 
rules do not currently satisfy including those deficiencies cited in 
EPA's Evaluation Report Addendum which still apply despite EPA's new NSR 
requirements (contained in Document File NAP-CA-07 at the EPA Library in 
Washington, DC and the Regional Office).
    (ii) [Reserved]
    (6) The San Joaquin Valley Air Basin Nonattainment Area.
    (i) For O3, PM and CO in San Joaquin County.
    (A) By October 30, 1985 the NSR rules must be revised to meet the 
requirements in EPA's amended regulations for NSR under section 173 of 
the Clean Air Act (May 13, 1980 (45 FR 31307) and August 7, 1980 (45 FR 
52676)) and submitted as a SIP revision.
    (7) San Francisco Bay Area Air Basin.
    (i) For ozone and CO:
    (A) By June 17, 1982, submittal of implementation commitments and 
schedules and additional commitments to provide annually the financial 
and personnel resources necessary to carry out the plan for 
transportation sources.
    (8) [Reserved]
    (9) The Santa Barbara County nonattainment areas.
    (i) For O3, TSP, and CO by (90 days from the date of 
publication of this notice).
    (A) The new source review (NSR) rules must be revised to meet the 
requirements in EPA's amended regulations for NSR under section 173 of 
the Clean Air Act (45 FR 31307, May 13, 1980 and 45 FR 52676, August 7, 
1980) and submitted as an SIP revision.
    (ii) For O3 by (90 days from the date of publication of 
this notice), a revised cutback asphalt paving materials rule which does 
not allow for indefinite compliance date extensions and submitted as an 
SIP revision.
    (10) Kings, Madera, Merced, Stanislaus and Tulare County APCDs.
    (i) For O3 and PM [and CO in Stanislaus County].
    (A) By September 7, 1982 the NSR rules must be revised to meet the 
requirements in EPA's amended regulations for NSR under section 173 of 
the Clean Air Act (May 13, 1980, 45 FR 31307 and August 7, 1980, 45 FR 
52676) as an SIP revision.
    (11) Fresno County and Ventura County nonattainment areas.
    (i) For ozone, CO (for Fresno County), and PM:
    (A) By November 1, 1982, the NSR rules must be revised to meet the 
requirements in EPA's amended regulations for NSR under section 173 of 
the Clean Air Act (May 13, 1980 (45 FR 31307), August 7, 1980 (45 FR 
52676), and October 14, 1981 (46 FR 50766)).
    (12) Butte, Sutter and Yuba County APCDs.
    (i) For Ozone:
    (A) By August 2, 1982, the NSR rules for the counties discussed in 
this notice must be revised to meet the requirements in EPA's amended 
regulations for NSR under section 173 of the Clean Air Act (May 13, 
1980, 45 FR 31307 and August 7, 1980, 45 FR 52676).
    (13) Los Angeles and Riverside portions of the Southeast Desert Air 
Basin.
    (i) For Ozone:
    (A) By August 9, 1982, the new source review rules for the three 
county areas

[[Page 161]]

must be revised to meet the requirements in EPA's amended regulations 
under section 173 (May 13, 1980, (45 FR 31307), August 7, 1980, (45 FR 
52676), and October 14, 1981, (46 FR 50766)).
    (B) By August 9, 1982, the State must provide adopted regulations 
for degreasing operations in the Los Angeles County portion of the SEDAB 
which represent RACT.
    (14) [Reserved]
    (15) Mountain Counties Air Basin.
    (i) By October 30, 1985 the new source review rules for Placer and 
El Dorado Counties must be revised to meet the requirements in EPA's 
amended regulations under section 173 of the Clean Air Act (May 13, 1980 
(45 FR 31307), August 7, 1980 (45 FR 52676), and October 14, 1981 (46 FR 
50766)).
    (16) San Bernardino County portion of the Southeast Desert Air 
Basin.
    (i) For ozone:
    (A) By October 30, 1985, the NSR rules must be revised to meet the 
requirements in EPA's amended regulations for NSR under section 173 of 
the Clean Air Act (May 13, 1980 (45 FR 31307), August 7, 1980 (45 FR 
52676), and October 14, 1981 (46 FR 50766)).
    (17) Yolo and Solano Counties.
    (i) For ozone and CO in those portions of Yolo and Solano Counties 
that are part of the Sacramento Metropolitan Area:
    (A) By October 30, 1985, the NSR rules must be revised to meet the 
requirements in EPA's amended regulations for NSR under section 173 of 
the Clean Air Act (May 13, 1980 (45 FR 31307), August 7, 1980 (45 FR 
52676), and October 14, 1981 (46 FR 50766)).
    (ii) For ozone:
    By November 1, 1982, the State must provide either (A) an adequate 
demonstration that the following regulations represent RACT, (B) amend 
the regulations so that they are consistent with the CTG, or (C) 
demonstrate that the regulations will result in VOC emission reductions 
which are within five percent of the reductions which would be achieved 
through the implementation of the CTG recommendations:

                         Yolo-Solano County APCD

    Rule 2.24, ``Solvent Cleaning Operations (Degreasing).''
[45 FR 74485, Nov. 10, 1980]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.232, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.233  Review of new sources and modifications.

    (a) The following regulations are disapproved because they are not 
consistent with Clean Air Act requirements.
    (1) Imperial County APCD.
    (i) Subparagraph C.5. of Rule 207, Standards for Permit to 
Construct, submitted March 17, 1980.
    (2) Monterey Bay Unified APCD.
    (i) Subparagraph B.5. of Rule 207, Standards for Permit to 
Construct, submitted March 17, 1980.
    (3) South Coast AQMD.
    (i) In Rule 1306(a)(i), submitted on April 3, 1980, sentence 3 is 
disapproved.
    (ii) In Rule 1306(d)(1)(B)(ii), submitted on April 3, 1980, the 
following portion of the rule is disapproved: ``Which have occurred 
during the highest three years of the last five year period, divided by 
three, provided the applicant demonstrates that such permit units have 
been operated at least 90 days during each of such three years.''
    (iii) In Rule 1307(a) submitted on April 3, 1980, the following 
portion of the rule is disapproved: ``Greater than 68 kilograms (150 
pounds) per day except carbon monoxide, for which the value is an 
increase greater than 340 kilograms (750 pounds) per day.''
    (4) Kern County APCD.
    (i) Those portions of paragraph (3)(E) of Rule 210.1, submitted on 
April 15, 1980, which allow new sources and modifications to be exempt 
from LAER.
    (b) [Reserved]
    (c) The requirements of Sec. 51.160(a) of this chapter are not met 
in the following Air Pollution Control Districts since the regulations 
of the APCD's do not provide the means to prevent construction of 
sources which would violate applicable portions of the control

[[Page 162]]

strategy or would interfere with the attainment or maintenance of a 
national standard.
    (1) Mariposa County APCD.
    (2) Santa Barbara County APCD.
    (d) The requirements of Sec. 51.160(a) of this chapter are not met 
in the following Air Pollution Control Districts since the regulations 
of the APCD's do not include a means to prevent construction or 
modification if such construction or modification would interfere with 
the attainment or maintenance of a national standard.
    (1) Amador County APCD.
    (2) Calaveras County APCD.
    (3) El Dorado County APCD (Mountain Counties Intrastate portion).
    (4) [Reserved]
    (5) Glenn County APCD.
    (6) Humboldt County APCD.
    (7)-(8) [Reserved]
    (9) Lake County APCD.
    (10) Lassen County APCD.
    (11) [Reserved]
    (12) Mendocino County APCD.
    (13) [Reserved]
    (14) Modoc County APCD.
    (15) Monterey Bay Unified APCD.
    (16) Nevada County APCD.
    (17) Northern Sonoma County APCD.
    (18) [Reserved]
    (19) Plumas County APCD.
    (20) [Reserved]
    (21) Shasta County APCD.
    (22) Sierra County APCD.
    (23) Siskiyou County APCD.
    (24) [Reserved]
    (25) Sutter County APCD.
    (26) [Reserved]
    (27) Tuolumne County APCD.
    (e) [Reserved]
    (f) Regulation for review of new sources and modifications. (1) The 
requirements of this paragraph are applicable to:
    (i) Any stationary source in the APCD's listed below, the 
construction or modification of which is commenced after the effective 
date of this regulation.
    (a) Mariposa County APCD.
    (b) [Reserved]
    (c) Santa Barbara County APCD.
    (ii) Any stationary source subject to the requirements of 
Secs. 52.226(c), 52.227(c), 52.228(b), or 52.230(b), the construction or 
modification of which is commenced after the effective date of this 
regulation.
    (2) No owner or operator shall commence construction or modification 
of a stationary source after the effective date of this regulation 
without first obtaining approval from the Administrator of the location 
and design of such source.
    (i) Application for approval to construct or modify shall be made on 
forms furnished by the Administrator, or by other means prescribed by 
the Administrator.
    (ii) A separate application is required for each source.
    (iii) Each application shall be signed by the applicant.
    (iv) Each application shall be accompanied by site information, 
plans, descriptions, specifications, and drawings showing the design of 
the source, the nature and amount of emissions, and the manner in which 
it will be operated and controlled.
    (v) Any additional information, plans, specifications, evidence, or 
documentation that the Administrator may require shall be furnished upon 
request.
    (3) No approval to construct or modify will be granted unless the 
applicant shows to the satisfaction of the Administrator that:
    (i) The source will be operated without causing a violation of any 
local, State, or Federal regulations which are part of the applicable 
plan.
    (ii) The source will not prevent or interfere with attainment or 
maintenance of any national standard.
    (4) (i) Within twenty (20) days after receipt of an application to 
construct, or any addition to such application, the Administrator shall 
advise the owner or operator of any deficiency in the information 
submitted in support of the application. In the event of such a 
deficiency, the date of receipt of the application for the purpose of 
paragraph (f)(4)(ii) of this section, shall be the date on which all 
required information is received by the Administrator.
    (ii) Within thirty (30) days after receipt of a complete 
application, the Administrator shall:
    (a) Make a preliminary determination whether the source should be 
approved, approved with conditions, or disapproved.

[[Page 163]]

    (b) Make available in at least one location in each region in which 
the proposed source would be constructed, a copy of all materials 
submitted by the owner or operator, a copy of the Administrator's 
preliminary determination and a copy or summary of other materials, if 
any, considered by the Administrator in making his preliminary 
determination; and
    (c) Notify the public, by prominent advertisement in a newspaper of 
general circulation in each region in which the proposed source would be 
constructed, of the opportunity for written public comment on the 
information submitted by the owner or operator and the Administrator's 
preliminary determination on the approvability of the source.
    (iii) A copy of the notice required pursuant to this paragraph shall 
be sent to the applicant and to state and local air pollution control 
agencies, having cognizance over the location where the source will be 
situated.
    (iv) Public comments submitted in writing within thirty (30) days 
after the date such information is made available shall be considered by 
the Administrator in making his final decision on the application. No 
later than ten (10) days after the close of the public comment period, 
the applicant may submit a written response to any comment submitted by 
the public. The Administrator shall consider the applicant's response in 
making his final decision. All comments shall be made available for 
public inspection in at least one location in the region in which the 
source would be located.
    (v) The Administrator shall take final action on the application 
within thirty (30) days after the close of the public comment period. 
The Administrator shall notify the applicant in writing of his approval, 
conditional approval, or denial of the application, and shall set forth 
his reasons for ocnditional approval or denial. Such notification shall 
be made available for public inspection in at least one location in the 
region in which the source would be located.
    (vi) The Administrator may extend each of the time periods specified 
in paragraph (f)(4)(ii), (iv) or (v) of this section by no more than 30 
days, or such other period as agreed to by the applicant and the 
Administrator.
    (5) The Administrator may impose any reasonable conditions upon an 
approval, including conditions requiring the source to be provided with:
    (i) Sampling ports of a size, number, and location as the 
Administrator may require,
    (ii) Safe access to each port,
    (iii) Instrumentation to monitor and record emission data, and
    (iv) Any other sampling and testing facilities.
    (6) The Administrator may cancel an approval if the construction is 
not begun within 2 years from the date of issuance, or if during the 
construction, work is suspended for 1 year.
    (7) Any owner or operator subject to the provisions of this 
regulation shall furnish the Administrator written notification as 
follows:
    (i) A notification of the anticipated date or initial startup of the 
source not more than 60 days or less than 30 days prior to such date.
    (ii) A notification of the actual date of initial startup of the 
source within 15 days after such date.
    (8) Within 60 days after achieving the maximum production rate at 
which the source will be operated but not later than 180 days after 
initial startup of such source the owner or operator of such source 
shall conduct a performance test(s) in accordance with methods and under 
operating conditions approved by the Administrator and furnish the 
Administrator a written report of the results of such performance test.
    (i) Such test shall be at the expense of the owner or operator.
    (ii) The Administrator may monitor such test and may also conduct 
performance tests.
    (iii) The owner or operator of a source shall provide the 
Administrator 15 days prior notice of the performance test to afford the 
Administrator the opportunity to have an observer present.
    (iv) The Administrator may waive the requirement for performance 
tests if the owner or operator of a source has demonstrated by other 
means to the Administrator's satisfaction that the source is being 
operated in compliance

[[Page 164]]

with all local, State and Federal regulations which are part of the 
applicable plan.
    (9) Approval to construct or modify shall not be required for:
    (i) The installation or alteration of an air pollutant detector, air 
pollutants recorder, combustion controller, or combustion shutoff.
    (ii) Air-conditioning or ventilating systems not designed to remove 
air pollutants generated by or released from equipment.
    (iii) Fuel burning equipment, other than smokehouse generators which 
has a heat input of not more than 250 MBtu/h (62.5 billion g-cal/h) and 
burns only gaseous fuel containing not more than 0.5 grain H2 
S per 100 stdft 3 (5.7 g/100 stdm 3); has a heat 
input of not more than 1 MBtu/h (250 Mg-cal/h) and burns only distillate 
oil; or has a heat input of not more than 350,000 Btu/h (88.2 Mg-cal/h) 
and burns any other fuel.
    (iv) Mobile internal combustion engines.
    (v) Laboratory equipment used exclusively for chemical or physical 
analyses.
    (vi) Other sources of minor significance specified by the 
Administrator.
    (10) Approval to construct or modify shall not relieve any person of 
the responsibility to comply with any local, State, or Federal 
regulation which is part of the applicable plan.
    (11) Any owner or operator who constructs, modifies, or operates a 
stationary source not in accordance with the application, as approved 
and conditioned by the Administrator, or any owner or operator of a 
stationary source subject to this paragraph who commences construction 
or modification without applying for any receiving approval hereunder, 
shall be subject to enforcement action under section 113 of the Act.
    (g) Regulation for review of new sources and modifications. (1) The 
requirements of this paragraph are applicable to any stationary source 
in the APCD's listed below, the construction or modification of which is 
commenced after the effective date of this regulation.
    (i) Amador County APCD.
    (ii) Calaveras County APCD.
    (iii) El Dorado County APCD (Mountain Counties Intrastate portion).
    (iv) [Reserved]
    (v) Glenn County APCD.
    (vi) Humboldt County APCD.
    (vii)-(viii) [Reserved]
    (ix) Lassen County APCD.
    (x) Madera County APCD.
    (xi) Mendocino County APCD.
    (xii) Merced County APCD.
    (xiii) Modoc County APCD.
    (xiv) Monterey Bay Unified APCD.
    (xv) Nevada County APCD.
    (xvi) [Reserved]
    (xvii) Plumas County APCD.
    (xviii) San Joaquin County APCD.
    (xix) Shasta County APCD.
    (xx) Sierra County APCD.
    (xxi) Siskiyou County APCD.
    (xxii) Stanislaus County APCD.
    (xxiii) Sutter County APCD.
    (xxiv) Tulare County APCD.
    (xxv) Tuolumne County APCD.
    (2) No owner or operator shall commence construction or modification 
of any new source after the effective date of this regulation without 
first obtaining approval from the Administrator of the location of such 
source.
    (i) Application for approval to construct or modify shall be made on 
forms furnished by the Administrator, or by other means prescribed by 
the Administrator.
    (ii) A separate application is required for each source.
    (iii) Each application shall be signed by the applicant.
    (iv) Each application shall be accompanied by site information, 
stack data, and the nature and amount of emissions. Such information 
shall be sufficient to enable the Administrator to make any 
determination pursuant to paragraph (g)(3) of this section.
    (v) Any additional information, plans, specifications, evidence, or 
documentation that the Administrator may require shall be furnished upon 
request.
    (3) No approval to construct or modify will be granted unless the 
applicant shows to the satisfaction of the Administrator that the source 
will not prevent or interfere with attainment or maintenance of any 
national standard.
    (4) (i) Within twenty (20) days after receipt of an application to 
construct, or any addition to such application, the Administrator shall 
advise the

[[Page 165]]

owner or operator of any deficiency in the information submitted in 
support of the application. In the event of such a deficiency, the date 
of receipt of the application for the purpose of paragraph (g)(4)(ii) of 
this section, shall be the date on which all required information is 
received by the Administrator.
    (ii) Within thirty (30) days after receipt of a complete 
application, the Administrator shall:
    (a) Make a preliminary determination whether the source should be 
approved, approved with conditions, or disapproved.
    (b) Make available in at least one location in each region in which 
the proposed source would be constructed, a copy of all materials 
submitted by the owner or operator, a copy of the Administrator's 
preliminary determination and a copy or summary of other materials, if 
any, considered by the Administrator in making his preliminary 
determination; and
    (c) Notify the public, by prominent advertisement in a newspaper of 
general circulation in each region in which the proposed source would be 
constructed, of the opportunity for written public comment on the 
information submitted by the owner or operator and the Administrator's 
preliminary determination on the approvability of the source.
    (iii) A copy of the notice required pursuant to this subparagraph 
shall be sent to the applicant and to state and local air pollution 
control agencies, having cognizance over the location where the source 
will be situated.
    (iv) Public comments submitted in writing within thirty (30) days 
after the date such information is made available shall be considered by 
the Administrator in making his final decision on the application. No 
later than ten (10) days after the close of the public comment period, 
the applicant may submit a written response to any comment submitted by 
the public. The Administrator shall consider the applicant's response in 
making his final decision. All comments shall be made available for 
public inspection in at least one location in the region in which the 
source would be located.
    (v) The Administrator shall take final action on an application 
within thirty (30) days after the close of the public comment period. 
The Administrator shall notify the applicant in writing of his approval, 
conditional approval, or denial of the application, and shall set forth 
his reasons for conditional approval or denial. Such notification shall 
be made available for public inspection in at least one location in the 
region in which the source would be located.
    (vi) The Administrator may extend each of the time periods specified 
in paragraph (g)(4) (ii), (iv) or (v) of this section by no more than 30 
days, or such other period as agreed to by the applicant and the 
Administrator.
    (5) The Administrator may cancel an approval if the construction is 
not begun within 2 years from the date of issuance, or if during the 
construction, work is suspended for 1 year.
    (6) Approval to construct or modify shall not relieve any owner or 
operator of the responsibility to comply with any local, State, or 
Federal regulation which is part of the applicable plan.
    (7) Approval to construct or modify shall not be required for:
    (i) The installation or alteration of an air pollutant detector, air 
pollutants recorder, combustion controller, or combustion shutoff.
    (ii) Air-conditioning or ventilating systems not designed to remove 
air pollutants generated by or released from equipment.
    (iii) Fuel burning equipment, other than smokehouse generators, 
which has a heat input of not more than 250 MBtu/h (62.5 billion g-cal/
h) and burns only gaseous fuel containing not more than 20.0 grain 
H2 S per 100 stdft 3 (54.8 g/100 stdm 
3); has a heat input of not more than 1 MBtu/h (250 Mg-cal/h) 
and burns only distillate oil; or has a heat input of not more than 
350,000 Btu/h (88.2 Mg-cal/h) and burns any other fuel.
    (iv) Mobile internal combustion engines.
    (v) Laboratory equipment used exclusively for chemical or physical 
analyses.
    (vi) Other sources of minor significance specified by the 
Administrator.
    (8) Any owner or operator who constructs, modifies, or operates a 
stationary source not in accordance with the

[[Page 166]]

application, as approved and conditioned by the Administrator, or any 
owner or operator of a stationary source subject to this paragraph who 
commences construction or modification without applying for and 
receiving approval hereunder, shall be subject to enforcement action 
under section 113 of the Act.
    (h)--(i) [Reserved]
    (j) Delegation of authority. (1) The Administrator shall have the 
authority to delegate responsibility for implementing the procedures for 
conducting source review pursuant to this section in accordance with 
paragraphs (j) (2), (3), and (4) of this section.
    (2) Where the Administrator delegates the responsibility for 
implementing the procedures for conducting source review pursuant to 
this section to any Agency, other than a Regional Office of the 
Environmental Protection Agency, a copy of the notice pursuant to 
paragraphs (f)(4)(iii) and (g)(4)(iii) of this section shall be sent to 
the Administrator through the appropriate Regional Office.
    (3) In accordance with Executive Order 11752, the Administrator's 
authority for implementing the procedures for conducting source review 
pursuant to this section shall not be delegated, other than to a 
Regional Office of the Environmental Protection Ands; except that, with 
respect to the latter category, where new or modified sources are 
constructed or operated on Federal lands pursuant to leasing or other 
Federal agreements, the Federal Land Manager may at his discretion, to 
the extent permissible under applicable statutes and regulations, 
require the lessee or permittee to be subject to new source review 
requirements which have been delegated to a state or local agency 
pursuant to this paragraph.
    (4) The Administrator's authority for implementing the procedures 
for conducting source review pursuant to this section shall not be 
redelegated, other than to a Regional Office of the Environmental 
Protection Agency, for new or modified sources which are located in 
Indian reservations except where the State has assumed jurisdiction over 
such land under other laws, in which case the Administrator may delegate 
his authority to the States in accordance with paragraphs (j) (2), (3), 
and (4) of this section.
    (k) Conditions on steam production. (1) Notwithstanding any 
provisions to the contrary in the California State Implementation Plan, 
the Watson petroleum refinery owned by Atlantic Richfield Company, 
located at 1801 East Sepulveda Boulevard, Carson, California, shall 
operate under the following conditions listed in paragraphs (k)(2) 
through (6) of this section.
    (2) The total steam load comprised of the steam purchased from 
Watson Energy Systems and the amount generated by boilers 31, 32, 33, 
42, 51, and 52 at the ARCO Watson Refinery shall not exceed 1,355,000 
pounds per hour at 680 deg.F, 600 psig.
    (3) Continuous written records of steam purchased from Watson Energy 
Systems and of the steam produced by boilers 31, 32, 42, 51, or 52 
at the ARCO Watson Refinery, during receipt of steam from Watson Energy 
Systems, shall be maintained and made available for inspection by the 
EPA and the South Coast Air Quality Management District. These records 
shall be kept in terms of pounds per hour of steam at 680 deg.F, 600 
psig.
    (4) The steam purchased from the Watson Energy Systems facility 
shall be used as a ``first-on, last-off'' source of steam for the ARCO 
Watson Refinery, except for steam produced by waste heat or as part of 
the refining process, or as required to maintain fired boilers in 
service for emergency use.
    (5) Any proposed changes in equipment or fuel that would increase 
the oil fired steam generating capacity or decrease oil fired steam 
generating efficiency of boilers 31, 32, 33, 42, 51, and 52 at the 
ARCO Watson Refinery must be reviewed and approved by the EPA prior to 
implementation of the proposed changes.
    (6) ARCO shall maintain written records of oil consumption at 
boilers 31, 32, 33, 42, 51, and 52 during receipt of steam from 
Watson Energy Systems. These records shall be available for inspection 
by the South Coast Air Quality Management District and the EPA. The 
total oil consumption of these boilers shall not exceed a monthly 
average of 226,000 gallons per day

[[Page 167]]

when receiving steam from the Watson Energy systems plant at a rate of 
350,000 pounds per hour. When receiving steam at a lower rate, ARCO 
shall be allowed to increase its boiler fuel oil consumption to achieve 
a total steam load not to exceed the limit of condition two (2).
    (l) The following rules and regulations are disapproved because they 
do not meet the requirements of sections 110, 172, and 173 of the Clean 
Air Act, since they exempt certain source categories from the offset 
requirements of the Act:
    (1) South Coast Air Quality Management District.
    (i) Rule 1304(e), Resource Conservation and Energy Projects, 
submitted on April 3, 1980, but only with respect to projects whose 
application for a permit is complete after January 1, 1986,
    (ii) Rule 1304(b)(2), Resource and Energy Conservation Projects, 
submitted on November 8, 1982, but only with respect to projects whose 
application for a permit is complete after January 1, 1986,
    (m) Revised South Coast Regulation XIII, submitted on November 8, 
1982, is not approved inasmuch as action on it is temporarily deferred.
[37 FR 19813, Sept. 22, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.233, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.234  Source surveillance.

    (a) Except in the Air Pollution Control Districts (APCDs) listed in 
this paragraph, the requirements of Sec. 51.211 of this chapter are not 
met since the plan does not provide for recordkeeping and periodic 
reporting of emission data by sources.
    (1) Amador County APCD.
    (2) Bay Area AQMD.
    (3) Calaveras County APCD.
    (4) Del Norte County APCD.
    (5) El Dorado County APCD.
    (6) Humboldt County APCD.
    (7) Imperial County APCD.
    (8) Lake County APCD.
    (9) Mariposa County APCD.
    (10) Mendocino County APCD.
    (11) Nevada County APCD.
    (12) Northern Sonoma County APCD.
    (13) Placer County APCD.
    (14) Plumas County APCD.
    (15) Sierra County APCD.
    (16) Trinity County APCD.
    (17) Ventura County APCD.
    (b) The requirements of Sec. 51.212 of this chapter are not met 
since the plan does not adequately provide for periodic testing and 
inspection of stationary sources within the Bay Area Air Pollution 
Control District portion of the San Francisco Bay Area Intrastate 
Region.
    (c) The requirements of Sec. 51.212 of this chapter are not met 
since the system for detecting violations through enforcement of visible 
emission regulations and complaint handling is not adequately described.
    (d) Regulation for source recordkeeping and reporting. (1) The owner 
or operator of any stationary source in the State of California, except 
for those APCD's specified in paragraph (a) of this section, shall, upon 
notification from the Administrator, maintain records of the nature and 
amounts of emissions from such source and/or any other information as 
may be deemed necessary by the Administrator to determine whether such 
source is in compliance with applicable emission limitations or other 
control measures.
    (2) The information recorded shall be summarized and reported to the 
Administrator, on forms furnished by the Administrator, and shall be 
submitted within 45 days after the end of the reporting period. 
Reporting periods are January 1 to June 30 and July 1 to December 31, 
except that the initial reporting period shall commence on the date the 
Administrator issues notification of the recordkeeping requirements.
    (3) Information recorded by the owner or operator and copies of the 
summarizing reports submitted to the Administrator shall be retained by 
the owner or operator for 2 years after the date on which the pertinent 
report is submitted.
    (e) The requirements of Sec. 51.214 of this chapter are not met in 
the following air pollution control districts (APCD's) since all of the 
applicable requirements of Appendix P of part 51 are not included in the 
district regulations.
    (1) Amador County APCD.
    (2) Bay Area AQMD

[[Page 168]]

    (3) Calaveras County APCD.
    (4) El Dorado County APCD.
    (5) Imperial County APCD.
    (6) Kern County APCD.
    (7) Kings County APCD.
    (8) Los Angeles County APCD.
    (9) Mariposa County APCD.
    (10) Monterey Bay Unified APCD.
    (11) Nevada County APCD.
    (12) Placer County APCD.
    (13) Plumas County APCD.
    (14) San Bernardino County Desert APCD.
    (15) San Diego County APCD.
    (16) San Joaquin County APCD.
    (17) San Luis Obispo County APCD.
    (18) Santa Barbara County APCD.
    (19) Sierra County APCD.
    (20) South Coast AQMD.
    (21) Stanislaus County APCD.
    (22) Tulare County APCD.
    (23) Ventura County APCD.
[37 FR 10850, May 31, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.234, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.235  Control strategy for ozone: Oxides of nitrogen.

    EPA is approving an exemption request submitted by the Monterey Bay 
Unified Air Pollution Control District on April 26, 1994 for the 
Monterey Bay ozone nonattainment area from the NOX RACT 
requirements contained in section 182(f) of the Clean Air Act. This 
approval exempts the area from implementing the oxides of nitrogen 
(NOX) requirements for reasonably available control 
technology (RACT), new source review (NSR), the related requirements of 
general and transportation conformity regulations, and applicable 
inspection and maintenance (I/M). The exemption is based on ambient air 
monitoring data and lasts for only as long as the area's monitoring 
efforts continue to demonstrate attainment without NOX 
reductions from major stationary sources.
[60 FR 20237, Apr. 25, 1995]



Sec. 52.236  Rules and regulations.

    (a) Since the following Air Pollution Control District (APCD) rules 
do not define the term ``agricultural operations,'' the rules are 
disapproved because they could render certain emission limitations rules 
unenforceable.
    (1) Imperial County APCD.
    (i) Rule 114.5, submitted on November 10, 1976.
    (ii) Rule 148.D(3), submitted on November 10, 1976.
    (b) The following Air Pollution Control District (APCD) rules are 
disapproved because they contain the term ``agricultural operations'' 
and/or the term ``other equipment in agricultural operations,'' both of 
which are either undefined or inadequately defined, thus rendering 
certain emission control rules unenforceable:
    (1) San Luis Obispo County APCD.
    (i) Rules 401(B)(4) and 401(B)(6), submitted on November 10, 1976.
    (2) Sacramento County APCD.
    (i) Rule 7(b)(5), submitted on November 4, 1977.
    (3) Glenn County APCD.
    (i) Section 77(e), submitted on June 30, 1972, and previously 
approved under 40 CFR 52.223 (37 FR 19812).
    (4) Mariposa County APCD.
    (i) Rule 203(G), submitted on June 6, 1977.
    (5) Kern County APCD.
    (i) Rules 402(c) and 402(e), submitted on; November 10, 1976.
    (6) Fresno County APCD.
    (i) Rules 402(c) and 402(e), submitted on October 23, 1974.
    (ii) Rules 402(c) and 402(e), submitted on June 30, 1972, and 
previously approved under 40 CFR 52.223 (37 FR 19812).
    (7) Tulare County APCD.
    (i) Section 402(c), submitted on November 10, 1976, and previously 
approved under 40 CFR 52.223 (42 FR 47556).
    (8) Madera County APCD.
    (i) Rules 402(c) and 402(e), submitted on January 10, 1975, and 
previously approved under 40 CFR 52.223 (42 FR 42219).
    (9) Amador County APCD.
    (i) Rules 203(G), submitted on October 15, 1979, and 205(G), 
submitted on June 30, 1972.
    (c) Since the following Air Pollution Control Districts have deleted 
definitions which could allow a relaxation of emission limitations, the 
deletions are disapproved:
    (1) Merced County APCD.

[[Page 169]]

    (i) Rule 102(hh), submitted on June 30, 1972, previously approved 
under 40 CFR 52.223, and deleted by the August 2, 1976 submittal, is 
retained.
    (2) El Dorado County APCD.
    (i) Rule 102(LL), submitted on November 4, 1977, previously approved 
at 43 FR 51632, and deleted by the May 23, 1979 submittal, is retained.
    (d) The following rules or portions of rules are disapproved since 
they contain provisions which are inconsistent with 40 CFR part 58, 
Ambient Air Quality Surveillance.
    (1) Lake County APCD.
    (i) Section 224, Equivalent Method, and Table V, Table of Standards, 
Applicable Statewide, submitted on February 10, 1977.
    (ii) Table V, Concentrations and Methods, submitted on January 2, 
1979, and Table V, submitted on February 10, 1976 and previously 
approved at 42 FR 42224.
    (e) Since the following air pollution control districts have revised 
definitions so as to render the associated emission control requirements 
less stringent without a control strategy demonstration, the revisions 
are disapproved.
    (1) Mendocino County APCD.
    (i) Rule 130(p4), submitted on November 10, 1976. (Part III-49, 
previously submitted on February 21, 1972, and approved in 40 CFR 
52.223, is retained).
    (ii) Rule 130(s3), submitted on November 10, 1976. (Part III-55, 
previously submitted on February 21, 1972, and approved in 40 CFR 
52.233, is retained).
    (2) Shasta County APCD.
    (i) The definition of ``modification'' in Rule 1:2, Definitions, 
submitted on October 13, 1977, is disapproved.
    (3) San Bernardino County Desert APCD.
    (i) Rule 103, Definition of Terms, submitted on November 4, 1977, is 
disapproved with respect to the deletion of the following terms: 
``Distilling type heater'', ``Noncomplying orchard heater'', ``Pipe line 
systems'', and ``Return stack heater''. (Rule 2, Definitions, submitted 
on February 21, 1972 and approved in 40 CFR 52.223, is retained for the 
above terms.)
    (4) Southeast Desert Intrastate Region.
    (i) San Bernardino County Desert APCD.
    (A) Rule 102, Definition of Terms, submitted November 4, 1977 is 
disapproved with respect to the deletion of the following terms: 
Distilling type heater, Non-complying orchard heater, Pipe line systems, 
and Return stack heater. Rule 2, Definitions, submitted February 21, 
1972 and approved in 40 CFR 52.223, is retained for the above terms.
    (f) The following APCD rules are disapproved because they exempt 
some portions of the districts from the existing air pollution control 
regulations without setting forth substitute rules for the exempted 
areas.
    (1) El Dorado County APCD.
    (i) Rule 201, submitted on November 4, 1977, is disapproved. (The 
previously approved Rule 49, submitted on June 30, 1972, is retained for 
Federal enforcement purposes.)
    (g) The following Air Pollution Control District (APCD) rules are 
disapproved pursuant to section 110(a)(2)(K) of the Clean Air Act 
because they could allow recovery of legal expenses associated with 
permit enforcement actions.
    (1) Monterey Bay Unified APCD.
    (i) Rule 300 (i)(1), Permit Fee, submitted on December 17, 1979.
    (2) El Dorado County APCD.
    (i) Rule 104, submitted on May 23, 1979.
[42 FR 39664, Aug. 5, 1977]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.236, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.237  Part D disapproval.

    (a) The following portions of the California SIP are disapproved 
because they do not meet the requirements of Part D of the Clean Air 
Act.
    (1) The ozone and CO attainment demonstrations for the South Coast 
Air Basin. No major stationary source, or major modification of a 
stationary source, of carbon monoxide or volatile organic compounds may 
be constructed in the South Coast Air Basin unless the construction 
permit application is complete on or before August 30, 1988.
    (2) The ozone attainment demonstration for Ventura County. No major 
stationary source, or major modification of a stationary source, of 
volatile organic compounds may be constructed

[[Page 170]]

in the Ventura County nonattainment area unless the construction permit 
application is complete on or before November 4, 1988.
    (3) The ozone attainment demonstration for the Sacramento AQMA. No 
major stationary source, or major modification of a stationary source, 
of volatile organic compounds may be constructed in the Sacramento 
nonattainment area unless the construction permit application is 
complete on or before January 3, 1989.
    (4) The ozone attainment demonstration for the Fresno County APCD.
    (5) The ozone attainment demonstration for the Kern County APCD.
[46 FR 5979, Jan. 21, 1981, as amended at 48 FR 53118, Nov. 25, 1983; 50 
FR 35798; Sept. 4, 1985; 53 FR 1781, Jan. 22, 1988; 53 FR 39088, Oct. 5, 
1988; 53 FR 48537, Dec. 1, 1988; 55 FR 9878, 9880, Mar. 16, 1990; 56 FR 
2853, Jan. 25, 1991]



Sec. 52.238  Commitment to undertake rulemaking.

    (a) The Administrator shall undertake rulemaking, after the South 
Coast mobile source public consultative process, to promulgate any VOC 
and NOX mobile source controls which are determined to be 
appropriate for EPA and needed for ozone attainment in the Los Angeles-
South Coast Air Basin Area.
    (b) [Reserved]
[62 FR 1187, Jan. 8, 1997]



Sec. 52.239  Alternate compliance plans.

    (a) Alternative compliance plans (bubble plans) developed under the 
District rules listed below must be submitted to EPA by the State of 
California as SIP revisions. The emission limits contained in the 
District rule will continue to be enforceable by EPA and private 
citizens under sections 113 and 304(a) of the Act until the alternative 
compliance plans are approved by EPA for inclusion in the SIP.
    (1) Bay Area AQMD.
    (i) Rule 4 of Regulation 8, submitted on February 7, 1980.
    (b) Alternative compliance plans (bubble plans) developed under the 
District rules listed below are considered the applicable requirements 
in the SIP which are enforceable by EPA and private citizens under 
section 113 and 304(a) of the Act. Alternative compliance plans must be 
submitted to EPA after their approval by the District. The District 
rules do not apply to or supersede the conditions that a source must 
meet under nonattainment or PSD permit programs, new source performance 
standards, or national emission standards for hazardous air pollutants.
    (1) Bay Area AQMD.
    (i) Rules 11, 13 and 19 of Regulation 8, submitted on February 7, 
1980.
[47 FR 11870, Mar. 19, 1982]



Sec. 52.240  Compliance schedules.

    (a) The requirements of Sec. 51.262(a) of this chapter are not met 
in the following Air Pollution Control Districts since the regulations 
cited do not provide increments to progress toward compliance.
    (1) Rules 50-A, 52-A, 53-A(a), 53-A(b), 53-A(c), 53.2, 53.3, 54.A, 
58.A, 62.1, 68, 69, 70, and 71 of the San Bernardino County APCD.
    (2) Rules 53, 72.1, and 72.2 of the Riverside County APCD.
    (3) Rules 53, 66.c, and 68.a of the Orange County APCD.
    (4) Rule 39.1 of the Santa Barbara County APCD.
    (5) Rule 59 of the Ventura County APCD.
    (6) Rule 66(c) of the Los Angeles County APCD.
    (7) Rule 4.5 of the Siskiyou County APCD.
    (8) Rule 64(c) of the Northern Sonoma County APCD.
    (9) Rule 409 of the Tulare County APCD.
    (b) The requirements of Sec. 51.261 are not met since Rule 68.a of 
the Orange County Air Pollution Control District does not provide for 
compliance within 3 years after the Administrator's approval of the 
plan.
    (c) Federal compliance schedule. (1) Except as provided in paragraph 
(c)(2) of this section, the owner or operator of any stationary source 
subject to Rule 68.a of the Orange County Air Pollution Control District 
shall comply with such rule or regulation on or before January 31, 1974.
    (i) Any owner or operator in compliance with this rule on the 
effective date of this regulation shall certify such compliance to the 
Administrator

[[Page 171]]

no later than 120 days following the effective date of this paragraph.
    (ii) Any owner or operator who achieves compliance with such rule or 
regulation after the effective date of this regulation shall certify 
such compliance to the Administrator within 5 days of the date 
compliance is achieved.
    (2) Any owner or operator of a stationary source subject to 
paragraph (c)(1) of this section may, not later than 120 days following 
the effective date of this paragraph, submit to the Administrator for 
approval a proposed compliance schedule that demonstrates compliance 
with the rules and regulations specified in paragraph (c)(1) of this 
section as expeditiously as practicable but no later than July 31, 1975. 
The compliance schedule shall provide for increments of progress toward 
compliance. The dates for achievement of such increments of progress 
shall be specified. Increments of progress shall include, but not be 
limited to: Submittal of final control plan to the Administrator; 
letting of necessary contracts for construction or process changes or 
issuance of orders for the purchase of component parts to accomplish 
emission control or process modification; initiation of onsite 
construction or installation of emission control equipment or process 
modification; completion of onsite construction or installation of 
emissioncontrol equipment or process modification; and final compliance.
    (3) Any owner or operator who submits a compliance schedule pursuant 
to this paragraph shall, within 5 days after the deadline for each 
increment of progress, certify to the Administrator whether or not the 
required increment of the approved compliance schedule has been met.
    (d) Regulation for increments of progress. (1) The requirements of 
this paragraph are applicable to any stationary source in the following 
Air Pollution Control Districts subject to the indicated regulations.
    (i) Rules 50-A, 52-A, 53-A(a), 53-A(b), 53-A(c), 53.2, 53.3, 54.A, 
58.A, 62.1, 68, 69, 70, and 71 of the San Bernardino County APCD.
    (ii) Rules 53, 72.1, and 72.2 of the Riverside County APCD.
    (iii) Rules 53 and 66.c of the Orange County APCD.
    (iv) Rule 39.1 of the Santa Barbara County APCD.
    (v) Rule 59 of the Ventura County APCD.
    (vi) Rules 66(c) and 68 of the Los Angeles County APCD.
    (vii) Rule 4.5 of the Siskiyou County APCD.
    (viii) Rule 64(c) of the Northern Sonoma County APCD.
    (ix) Rule 409 of the Tulare County APCD.
    (2) Except as provided in paragraph (3) of this section, the owner 
or operator of any stationary source shall, no later than 120 days 
following the effective date of this paragraph, submit to the 
Administrator for approval, a proposed compliance schedule that 
demonstrates compliance with the applicable regulations as expeditiously 
as practicable but no later than the final compliance date specified by 
such applicable regulation. The compliance schedule shall provide for 
periodic increments of progress toward compliance. The dates for 
achievement of such increments shall be specified. Increments of 
progress shall include, but not be limited to: Submittal of final 
control plan to the Administrator; letting of necessary contracts for 
construction or process changes or issuance of orders for the purchase 
of component parts to accomplish emission control or process 
modification; initiation of onsite construction or installation of 
emission control equipment or process modification; completion of onsite 
construction or installation of emission control equipment or process 
modification; and final compliance.
    (3) Where any such owner or operator demonstrates to the 
satisfaction of the Administrator that compliance with the applicable 
regulations will be achieved on or before January 31, 1974, no 
compliance schedule shall be required.
    (4) Any owner or operator who submits a compliance schedule pursuant 
to this paragraph shall, within 5 days after the deadline for each 
increment

[[Page 172]]

of progress, certify to the Administrator whether or not the required 
increment of the approved compliance schedule has been met.
    (5) Any compliance schedule adopted by the State and approved by the 
Administrator shall satisfy the requirements of this paragraph for the 
affected source.
    (e) [Reserved]
    (f) State compliance schedules. (1) [Reserved]
    (2) The compliance schedules for the sources identified below are 
disapproved as not meeting the requirements of Subpart N of this 
chapter. All regulations cited are air pollution control regulations of 
the county in which the source is located, unless otherwise indicated.

--------------------------------------------------------------------------------------------------------------------------------------------------------
                                                               Rule or regulation
               Source                   Location (county)           involved            Date of adoption        Effective date     Final compliance date
--------------------------------------------------------------------------------------------------------------------------------------------------------
Simpson Lee Paper Co. (Order No. 72- Shasta................  3.2...................  Oct. 31, 1973........  Immediately..........  Jan. 15, 1976.
 V-7).
Monolith Portland Cement Co. (Order  Kern..................  401(b), 404.1, 406....  Dec. 31, 1973........  ......do.............  July 1, 1976.
 No. 73-6 as amended Mar. 11, 1974).
--------------------------------------------------------------------------------------------------------------------------------------------------------

[37 FR 19814, Sept. 22, 1972]

    Editorial Note:  For Federal Register citations affecting 
Sec. 52.240, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.241  Interim approval of enhanced inspection and maintenance program.

    (a) Under section 348(c) of the National Highway Systems Designation 
Act (Pub. L. 104-59), the California SIP is approved as meeting the 
provisions of section 182(c)(3) for applicable ozone areas and section 
187(a)(6) for applicable carbon monoxide areas with respect to the 
requirements for enhanced motor vehicle inspection and maintenance. This 
approval expires on August 7, 1998, or earlier if by such earlier date 
the State has submitted as a SIP revision the required demonstration 
that the credits are appropriate and that the program is otherwise in 
compliance with the Clean Air Act and EPA takes final action approving 
that revision.
[62 FR 1187, Jan. 8, 1997]



Secs. 52.242  [Reserved]



Sec. 52.243  Interim approval of the Carbon Monoxide plan for the South Coast.

    The Carbon Monoxide plan for the Los Angeles-South Coast Air Basin 
is approved as meeting the provisions of sections 171(1), 172(c)(2), and 
187(a)(7) for quantitative milestones and reasonable further progress, 
and the provisions of section 187(a)(7) for attainment demonstration. 
This approval expires on August 7, 1998, or earlier if by such earlier 
date the State has submitted as a SIP revision a demonstration that the 
carbon monoxide emission reduction credits for the enhanced motor 
vehicle inspection and maintenance program are appropriate and that the 
program is otherwise in compliance with the Clean Air Act and EPA takes 
final action approving that revision, as provided by section 348(c) of 
the National Highway System Designation Act (Public Law 104-59).
[63 FR 19662, Apr. 21, 1998]



Secs. 52.244--52.245  [Reserved]



Sec. 52.246  Control of dry cleaning solvent vapor losses.

    (a) For the purpose of this section, ``dry cleaning operation'' 
means that process by which an organic solvent is used in the commercial 
cleaning of garments and other fabric materials.
    (b) This section is applicable in the Metropolitan Los Angeles, 
Sacramento Valley, and San Joaquin Valley Intrastate Air Quality Control 
Regions (the ``Regions''), as described in 40 CFR part 81, dated July 1, 
1979, except as follows:
    (1) In the following portions of the Sacramento Valley Region, this 
section is rescinded:
    (i) Sacramento County APCD.
    (ii) Placer County APCD (Mountain Counties Air Basin portion).

[[Page 173]]

    (iii) Yuba County APCD.
    (iv) Sutter County APCD.
    (2) In the following portions of the Metropolitan Los Angeles 
Intrastate Region, this section is rescinded:
    (i) Ventura County APCD.
    (3) In the following portions of the San Joaquin Valley Intrastate 
Region, this section is rescinded:
    (i) San Joaquin County APCD.
    (ii) Stanislaus County APCD.
    (iii) Tulare County APCD.
    (iv) Fresno County APCD.
    (c) Any dry cleaning establishment that uses solvents containing 4 
percent or more by volume of any reactive organic material listed under 
paragraphs (k) (1), (2), and (3) of Sec. 52.254 except perchloroethylene 
or any saturated halogenated hydrocarbon shall reduce the emissions of 
the discharged organics by 90 percent by use of activated carbon 
adsorption, or other appropriate means, not later than January 1, 1975.
    (d) If incineration is used as a control technique, 90 percent or 
more of the carbon in the organic compounds being incinerated must be 
oxidized to carbon dioxide.
[38 FR 31246, Nov. 12, 1973, as amended at 42 FR 41122, Aug. 15, 1977; 
42 FR 42226, Aug. 22, 1977; 47 FR 15586, Apr. 12, 1982; 47 FR 18856, May 
3, 1982; 47 FR 26385, June 18, 1982; 47 FR 28622, July 1, 1982; 47 FR 
29670, July 8, 1982; 47 FR 50865, Nov. 10, 1982]



Secs. 52.247--52.251  [Reserved]



Sec. 52.252  Control of degreasing operations.

    (a) ``Degreasing'' means any operation using an organic solvent as a 
surface cleaning agent prior to fabricating, surface coating, 
electroplating, or any other process.
    (b) This section is applicable in the Sacramento Valley, San Joaquin 
Valley, and San Francisco Bay Area Intrastate Air Quality Control 
Regions (the ``Regions''), as described in 40 CFR part 81, dated July 1, 
1979, except as follows:
    (1) In the following portions of the Sacramento Valley Region, this 
section is rescinded:
    (i) Sacramento County APCD.
    (ii) Placer County APCD (Mountain Counties Air Basin portion).
    (iii) Yuba County APCD.
    (iv) Sutter County APCD.
    (c) Any organic emissions discharged from degreasing operations must 
either be reduced by at least 85 percent, or the degreasing solvent must 
be classified as non-photochemically reactive as defined by paragraph 
(k) of Sec. 52.254 not later than January 1, 1975. This regulation shall 
not be construed as lessening any emission control requirement specified 
under EPA approved regulations or Sec. 52.254. Degreasing operations 
using perchloroethylene or saturated halogenated hydrocarbons shall be 
exempt from the requirements of this section.
[38 FR 31249, Nov. 12, 1973, as amended at 42 FR 42226, Aug. 22, 1977; 
47 FR 15586, Apr. 12, 1982; 47 FR 18856, May 3, 1982; 47 FR 19332, May 
5, 1982; 47 FR 28622, July 1, 1982]



Sec. 52.253  Metal surface coating thinner and reducer.

    (a) All terms defined in Sec. 52.254 are used herein with the 
meanings so defined.
    (b) This section is applicable in the Metropolitan Los Angeles, San 
Diego, Sacramento Valley, San Joaquin Valley, and San Francisco Bay Area 
Intrastate Air Quality Control Regions (the ``Regions''), as described 
in 40 CFR part 81, dated July 1, 1979, except as follows:
    (1) In the following portions of the Sacramento Valley Intrastate 
Region, this section is either fully rescinded or partially rescinded 
subject to the conditions specified as follows:
    (i) Sacramento County APCD.
    (ii) Placer County APCD (Mountain Counties Air Basin portion).
    (iii) This section is rescinded for metal parts and products coaters 
which are subject to and in full compliance with Yolo-Solano County Rule 
2.25 submitted on February 25, 1980.
    (iv) Yuba County APCD.
    (v) Sutter County APCD.
    (2) In the following portions of the Metropolitan Los Angeles 
Intrastate Region, this section is either fully rescinded or partially 
rescinded subject to the conditions specified as follows:
    (i) This section is fully rescinded for the Ventura County APCD.
    (ii) This section is rescinded for magnet wire insulators, can and 
coil coaters, metal parts coaters, and auto assembly line coaters which 
are subject to and in full compliance with Rules

[[Page 174]]

1107, 1115, 1125, and 1126 in the South Coast AQMD.
    (iii) This section is rescinded for metal parts coaters that are 
subject to and in full compliance with Rule 330 submitted on October 18, 
1979, in the Santa Barbara County APCD.
    (3) In the following portions of the San Joaquin Valley Intrastate 
Region, this section is rescinded for certain sources subject to the 
conditions specified:
    (i) This section is rescinded for metal parts and products coaters 
which are subject to and in full compliance with Kern County Rule 410.4, 
submitted on October 15, 1979.
    (ii) This section is rescinded for metal parts and products coaters 
which are subject to and in full compliance with Madera County APCD's 
Rule 410.4 submitted on October 10, 1980.
    (iii) This section is rescinded for metal parts and products coaters 
which are subject to and in full compliance with Merced County Rule 
409.4 submitted on October 10, 1980.
    (iv) This section is rescinded for metal parts and products coaters 
which are subject to and in full compliance with San Joaquin County Rule 
409.4 submitted on October 10, 1980.
    (v) This section is rescinded for metal parts and products coaters 
which are subject to and in full compliance with Stanislaus County Rule 
410.4 submitted on October 10, 1980.
    (vi) This section is rescinded for metal parts and products coaters 
which are subject to and in full compliance with Tulare County Rule 
410.4 submitted on October 10, 1980.
    (vii) This section is rescinded for metal parts and products coaters 
which are subject to and in full compliance with Kings County Rule 410.4 
submitted on October 10, 1980.
    (viii) This section is rescinded for metal parts and products 
coaters which are subject to and in full compliance with Fresno County 
Rule 409.4 submitted on October 15, 1979.
    (4) In the San Francisco Bay Area Intrastate Region this section is 
rescinded for certain operations, subject to the conditions specified 
below:
    (i) This section is rescinded for metal container, closure and coil 
coating operations, light and medium-duty motor vehicle assembly plants, 
large appliance and metal furniture coaters, and miscellaneous metal 
parts and products coating operations, which are subject to and in full 
compliance with Rules 11, 13, 14, and 19 of Regulation 8 in the Bay Area 
AQMD.
    (5) In the San Diego Intrastate Region, this section is rescinded:
    (i) This section is rescinded for metal parts and products coaters 
which are subject to and in full compliance with San Diego APCD Rule 
67.3, submitted on October 25, 1979.
    (c) The composition of the organics in all metal surface coating 
thinners and reducers that are manufactured after January 1, 1975, and 
are used in the Regions, shall conform to paragraph (k) of Sec. 52.254 
so as to be defined as a nonphotochemically reactive solvent.
    (d) After July 1975, the composition of the organics in all metal 
surface coating thinners and reducers that are used in the Regions, 
shall conform to paragraph (k) of Sec. 52.254 so as to be defined as a 
non-photochemically reactive solvent.
    (e) If there is an inadequate supply of necessary solvent 
ingredients needed in the manufacture of metal surface coating thinners 
and reducers for the purpose of meeting the composition requirements of 
this section in the time constraint required by this section; then 
evidence of such a supply inadequacy must be presented to the 
Administrator by the manufacturers of the metal surface coating thinners 
and reducers, so that the Administrator may grant to the industry an 
appropriate implementation time extension for meeting the requirements 
of this section, if and as warranted by the evidence presented.
[38 FR 31249, Nov. 12, 1973, as amended at 42 FR 28123, June 2, 1977; 46 
FR 5979, Jan. 21, 1981; 46 FR 42461, Aug. 21, 1981; 47 FR 11870, Mar. 
19, 1982; 47 FR 15586, Apr. 12, 1982; 47 FR 18856, May 3, 1982; 47 FR 
19332, May 5, 1982; 47 FR 19698, May 7, 1982; 47 FR 24308, June 4, 1982; 
47 FR 28622, July 1, 1982]



Sec. 52.254  Organic solvent usage.

    (a) This section is applicable in the Sacramento Valley, San 
Francisco Bay Area, and San Joaquin Valley Intrastate Air Quality 
Control Regions (the

[[Page 175]]

``Regions''), as described in 40 CFR part 81, dated July 1, 1979, except 
as follows:
    (1) In the following portions of the San Joaquin Valley Region, only 
the hourly emission limitations contained in paragraphs (b), (c), and 
(d) of this section are in effect; the following paragraphs, needed for 
interpretation are also in effect: Paragraphs (e) through (l) and (o) 
through (q) of this section. In addition, this section is entirely 
rescinded for specific operations for some of the counties noted below:
    (i) This section is rescinded entirely for metal parts and products 
coaters which are subject to and in full compliance with Rule 409.4 for 
the Fresno County APCD, Rule 410.4 for the Kings County APCD, Rule 410.4 
for the Madera County APCD, Rule 409.4 for the Merced County APCD, Rule 
409.4 for the San Joaquin County APCD, Rule 409.4 for the Stanislaus 
County APCD, and Rule 410.4 for the Tulare County APCD.
    (ii) Kern County APCD. This section is rescinded entirely for metal 
parts and product coaters which are subject to and in full compliance 
with Rule 410.4.
    (iii) Fresno County APCD.
    (iv) San Joaquin County APCD.
    (v) Madera County APCD.
    (vi) Merced County APCD.
    (2) In the following portions of the San Joaquin Valley Region, only 
the hourly emission limitations contained in paragraphs (b), (c), and 
(d) of this section and the architectural coatings and solvent disposal 
emission limitations contained in paragraphs (m) and (n) of this section 
are in effect; the following paragraphs, needed for interpretation and 
enforcement of these emission limitations, are also in effect: 
Paragraphs (e) through (l) and (o) through (q) of this section.
    (i) Kings County APCD.
    (3) In the following portions of the Sacramento Valley Region, this 
section is rescinded:
    (i) Sacramento County APCD.
    (ii) Yolo-Solano APCD.
    (iii) Shasta County APCD.
    (iv) Placer County APCD (Mountain Counties Air Basin portion).
    (v) Yuba County APCD.
    (vi) Sutter County APCD.
    (vii) El Dorado County (Mountain Counties Air Basin portion).
    (4) This section is rescinded for the San Francisco Bay Area 
Intrastate Region except for paragraph (d), which is retained until 
December 31, 1982 for sources constructed prior to October 2, 1974. The 
following paragraphs, needed for interpretation and enforcement of 
paragraph (d) are also in effect: Paragraphs (e) through (l) and (o) 
through (q) of this section.
    (5) In the following portions of the Sacramento Valley Intrastate 
Region, paragraph (m) of this section is rescinded.
    (i) Butte County APCD.
    (ii) Sutter County APCD.
    (b) No person shall discharge into the atmosphere more than 15 
pounds of organic materials in any 1 day or more than 3 pounds in any 1 
hour from any article, machine, equipment, or other contrivance in which 
any organic solvent or any material containing organic solvent comes 
into contact with flame or is baked, heat-cured, or heat-polymerized in 
the presence of oxygen, unless said discharge has been reduced by at 
least 85 percent. Those portions of any series of articles, machines, 
equipment, or other contrivances designed for processing continuous web, 
strip, or wire that emit organic materials in the course of using 
operations described in this section shall be collectively subject to 
compliance with this section.
    (c) A person shall not discharge to the atmosphere more than 40 
pounds of organic materials in any 1 day or more than 8 pounds in any 1 
hour from any article, machine, equipment, or other contrivance used 
under conditions other than those described in paragraph (b) of this 
section for employing or applying any photochemically reactive solvent, 
as defined in paragraph (k) of this section, or material containing such 
photochemically reactive solvent, unless said discharge has been reduced 
by at least 85 percent. Emissions of organic materials into the 
atmosphere resulting from air- or heated-drying of products for the 
first 12 hours after their removal from any article, machine, or other 
contrivance described in this section shall be included in determining 
compliance with this

[[Page 176]]

paragraph. Emissions resulting from baking, heat-curing, or heat-
polymerizing as described in paragraph (b) of this section shall be 
excluded from determination of compliance with this section. Those 
portions of any series of articles, machines, equipment, or other 
contrivances designed for processing a continuous web, strip, or wire 
that emit organic materials in the course of using operations described 
in this section shall be collectively subject to compliance with this 
section.
    (d) A person shall not, after August 31, 1976, discharge into the 
atmosphere more than 3,000 pounds of organic materials in any 1 day or 
more than 450 pounds in any 1 hour from any article, machine, equipment, 
or other contrivance in which any non-photochemically reactive organic 
solvent or any material containing such a solvent is employed or 
applied, unless said discharge has been reduced by at least 85 percent. 
Emissions of organic materials into the atmosphere resulting from air- 
or heated-drying of products for the first 12 hours after their removal 
from any article, machine, equipment, or other contrivance described in 
this section shall be included in determining compliance with this 
section. Emissions resulting from baking, heat-curing, or heat-
polymerizing as described in paragraph (b) of this section shall be 
excluded from determination of compliance with this section. Those 
portions of any series of articles, machines, equipment, or other 
contrivances designed for processing a continuous web, strip, or wire 
that emit organic materials in the course of using operations described 
in this section shall be collectively subject to compliance with this 
section.
    (e) Emissions of organic materials to the atmosphere from the 
cleaning with photochemically reactive solvent, as defined in paragraph 
(k) of this section, of any article, machine, equipment, or other 
contrivance described in paragraph (b), (c), or (d) of this section, 
shall be included with the other emissions of organic materials for 
determining compliance with this rule.
    (f) Emissions of organic materials into the atmosphere required to 
be controlled by paragraph (b), (c), or (d) of this section, shall be 
reduced by:
    (1) Incineration, provided that 90 percent or more of the carbon in 
the organic material being incinerated is oxidized to carbon dioxide, or
    (2) Adsorption, or
    (3) Processing in a manner determined by the Administrator to be not 
less effective than the methods outlined in paragraph (f) (1) or (2) of 
this section.
    (g) A person incinerating, adsorbing, or otherwise processing 
organic materials pursuant to this section shall provide, properly 
install and maintain in calibration, in good working order and in 
operation, devices as specified in the authority to construct or permit 
to operate, or as specified by the Administrator, for indicating 
temperatures, pressures, rates of flow, or other operating conditions 
necessary to determine the degree and effectiveness of air pollution 
control.
    (h) Any person using organic solvents or any materials containing 
organic solvents shall supply the Administrator upon request and in the 
manner and form prescribed by him, written evidence of the chemical 
composition, physical properties, and amount consumed for each organic 
solvent used.
    (i) The provisions of this section shall not apply to:
    (1) The manufacture of organic solvents, or the transport or storage 
of organic solvents or materials containing organic solvents.
    (2) The use of equipment for which other requirements are specified 
by rules or which are exempted from air pollution control requirements 
by applicable rules affecting the storage of petroleum products, 
effluent oil-water separators, and the transfer of gasoline.
    (3) The spraying or other employment of insecticides, pesticides, or 
herbicides.
    (4) The employment, application, evaporation, or drying of saturated 
halogenated hydrocarbons or perchloroethylene.
    (5) The use of any material in any article, machine, equipment, or 
other contrivance described in paragraph (b), (c), (d), or (e) of this 
section, if:
    (i) The volatile content of such materials consists only of water 
and organic solvent, and

[[Page 177]]

    (ii) The organic solvents comprise not more than 20 percent by 
volume of said volatile content, and
    (iii) The volatile content is not photochemically reactive as 
defined in paragraph (k) of this section, and
    (iv) The organic solvent or any material containing organic solvent 
does not come into contact with flame.

This last stipulation applies only for those articles, machines, 
equipment, or contrivances that are constructed or modified after the 
effective date of this section.
    (6) The use of any material in any article, machine, equipment or 
other contrivance described in paragraph (b), (c), (d), or (e) of this 
section, if:
    (i) The organic solvent content of such material does not exceed 30 
percent by volume of said material; this to be effective until January 
1, 1977. After January 1, 1977, the organic solvent content of such 
material must not exceed 20 percent by volume of said material.
    (ii) The volatile content is not photochemically reactive as defined 
in paragraph (k) of this section, and
    (iii) The organic solvent or any material containing organic solvent 
does not come into contact with flame. This last stipulation applies 
only for those articles, machines, equipment, or contrivances that are 
constructed or modified after the effective date of this section.
    (j) For the purposes of this section, organic solvents include 
diluents, thinners, and reducers and are defined as organic materials 
that are liquids at standard conditions and are used as dissolvers, 
viscosity reducers, or cleaning agents, except that such materials 
exhibiting a boiling point higher than 220 deg. F at 0.5 millimeter 
mercury absolute pressure or having an equivalent vapor pressure shall 
not be considered to be solvents unless exposed to temperatures 
exceeding 220 deg. F.
    (k) For the purpose of this section, a photochemically reactive 
solvent is any solvent with an aggregate of more than 20 percent of its 
total volume composed of the chemical compounds classified below or 
which exceeds any of the following individual percentage composition 
limitations, referred to the total volume of solvent:
    (1) A combination of hydrocarbons, alcohols, aldehydes, esters, 
ethers, or ketones having an olefinic or cycloolefinic type of 
unsaturation; 5 percent;
    (2) A combination of aromatic compounds with 8 or more carbon atoms 
to the molecule except ethylbenzene, phenyl acetate, and methyl 
benzoate; 8 percent;
    (3) A combination of ethylbenzene, ketones having branched 
hydrocarbon structures, trichloroethylene or toluene: 20 percent.

Whenever any organic solvent or any constituent of an organic solvent 
may be classified from its chemical structure into more than one of the 
above groups of organic compounds, it shall be considered as a member of 
the most reactive chemical group, that is, that group having the least 
allowable percent of the total volume of solvents.
    (l) For the purpose of this section, organic materials are defined 
as chemical compounds of carbon excluding carbon monoxide, carbon 
dioxide, carbonic acid, metallic carbonates, and ammonium carbonate.
    (m) Architectural coatings and their use shall conform to the 
following requirements, on or before January 1, 1975:
    (1) A person shall not sell or offer for sale or use in the areas in 
which this section applies, in containers of 1-quart capacity or larger, 
any architectural coating containing photochemically reactive solvent, 
as defined in paragraph (k) of this section.
    (2) A person shall not employ, apply, evaporate, or dry in the areas 
in which this section applies, any architectural coating purchased in 
containers of 1-quart capacity or larger containing photochemically 
reactive solvent, as defined in paragraph (k) of this section.
    (3) A person shall not thin or dilute any architectural coating with 
a photochemically reactive solvent, as defined in paragraph (k) of this 
section.
    (4) For the purpose of this section, an architectural coating is 
defined as a coating used for residential or commercial buildings and 
their appurtenances, or for industrial buildings.
    (n) A person shall not during any one day dispose of a total of more 
than 1.5

[[Page 178]]

gallons of any photochemically reactive solvent as defined in paragraph 
(k) of this section, or of any material containing more than 1.5 gallons 
of any such photochemically reactive solvent by any means that will 
permit the evaporation of such solvent into the atmosphere.
    (o) Compliance schedule. (1) Except where other final compliance 
dates are provided in this section, the owner or operator of any 
stationary source subject to this section shall comply with this section 
on or before March 31, 1974. In any event:
    (i) Any owner or operator in compliance with this section on the 
effective date of this section shall certify such compliance to the 
Administrator no later than 120 days following the effective date of 
this section.
    (ii) Any owner or operator who achieves compliance with this section 
after the effective date of this section shall certify such compliance 
to the Administrator within 5 days of the date compliance is achieved.
    (p) Any owner or operator of a stationary source subject to 
paragraph (o)(1) of this section may, not later than 120 days following 
the effective date of this section, submit to the Administrator for 
approval a proposed compliance schedule that demonstrates compliance 
with the provisions in paragraph (o)(1) of this section as expeditiously 
as practicable but no later than July 31, 1975. The compliance schedule 
shall provide for increments of progress toward compliance. The dates 
for achievement of such increments of progress shall be specified. 
Increments of progress shall include, but not be limited to:

Submittal of a final control plan to the Administrator; letting of 
necessary contracts for construction or process changes or issuance of 
orders for the purchase of component parts to accomplish emission 
control or process modification; initiation of onsite construction or 
installation of emission control equipment or process modification; 
completion of onsite construction or installation of emission control 
equipment or process modification and final compliance.
    (q) Any owner or operator who submits a compliance schedule pursuant 
to this section shall, within 5 days after the deadline for each 
increment of progress, certify to the Administrator whether or not the 
required increment of the approved compliance schedule has been met.
[38 FR 31249, Nov. 12, 1973]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.254, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.255  Gasoline transfer vapor control.

    (a) ``Gasoline'' means any petroleum distillate having a Reid vapor 
pressure of 4 pounds or greater.
    (b) This section is applicable in the Metropolitan Los Angeles and 
Sacramento Valley Intrastate Air Quality Control Regions, as described 
in 40 CFR part 81, dated July 1, 1979, with the following exceptions:
    (1) The control requirements of this section are limited to 
facilities with a total throughput less than 20,000 gallons per day, the 
refilling of delivery vessels at these facilities, and storage 
containers serviced by these facilities for those air pollution control 
districts identified below.
    (i) Ventura County APCD.
    (2) The control requirements of this section are rescinded in the 
following air pollution control districts.
    (i) South Coast AQMD.
    (ii) Santa Barbara County APCD.
    (iii) Placer County APCD (Mountain Counties Air Basin portion).
    (iv) Sacramento County APCD.
    (v) Yolo-Solano County APCD.
    (vi) Butte County APCD.
    (vii) Glenn County APCD.
    (viii) El Dorado County APCD (Mountain Counties Air Basin portion).
    (3) The control requirements of this section are rescinded in the 
following air pollution control districts:
    (i) South Coast AQMD.
    (ii)-(viii) [Reserved]
    (ix) Santa Barbara County APCD.
    (x) Placer County APCD (Mountain Counties Air Basin portion).
    (xi) Sacramento County APCD.
    (xii) Yolo-Solano County APCD.
    (xiii) Butte County APCD.
    (xiv) Glenn County APCD.

[[Page 179]]

    (c) No person shall transfer gasoline from any delivery vessel into 
any stationary storage container with a capacity greater than 250 
gallons unless such container is equipped with a submerged fill pipe and 
unless the displaced vapors from the storage container are processed by 
a system that prevents release to the atmosphere of no less than 90 
percent by weight of organic compounds in said vapors displaced from the 
stationary container location.
    (1) The vapor recovery portion of the system shall include one or 
more of the following:
    (i) A vapor-tight return line from the storage container to the 
delivery vessel and a system that will ensure that the vapor return line 
is connected before gasoline can be transferred into the container.
    (ii) Refrigeration-condensation system or equivalent designed to 
recover no less than 90 percent by weight of the organic compounds in 
the displaced vapor.
    (2) If a ``vapor-tight vapor return'' system is used to meet the 
requirements of this section, the system shall be so constructed as to 
be readily adapted to retrofit with an adsorption system, refrigeration-
condensation system, or equivalent vapor removal system, and so 
constructed as to anticipate compliance with Sec. 52.256.
    (3) The vapor-laden delivery vessel shall be subject to the 
following conditions:
    (i) The delivery vessel must be so designed and maintained as to be 
vapor-tight at all times.
    (ii) The vapor-laden delivery vessel may be refilled only at 
facilities equipped with a vapor recovery system or the equivalent, 
which can recover at least 90 percent by weight of the organic compounds 
in the vapors displaced from the delivery vessel during refilling.
    (iii) Facilities that do not have more than a 20,000 gallon per day 
throughput, and distribute less than 10% of daily volume to delivery 
vehicles that in turn service storage tanks that are required to have a 
vapor return or balance system, will not be required to comply with the 
provisions of paragraph (c) of this section before May 31, 1977. 
Facilities that service delivery vehicles that in turn deliver not more 
than 500,000 gallons per year to storage tanks that are required to 
comply with the provisions of paragraph (c) of this section will not be 
required to comply with the provisions of paragraph (c) of this section 
before January 1, 1977. Facilities that exclusively service storage 
tanks that do not have a required vapor return or balance system, will 
not be required to have a vapor recovery system.
    (iv) Gasoline storage compartments of 1,000 gallons or less in 
gasoline delivery vehicles presently in use on the promulgation date of 
this regulation will not be required to be retrofitted with a vapor 
return system until May 31, 1977.
    (v) Storage containers served by delivery vessels filled at 
distribution facilities with extended compliance dates will not be 
required to comply with the provisions of paragraph (c) of this section 
until May 31, 1977.
    (d) The provisions of paragraph (c) of this section shall not apply 
to the following:
    (1) Storage containers used primarily for the fueling of implements 
of husbandry, if such container is equipped by May 31, 1977 with a 
permanent submerged fill pipe, or at the time of installation for 
containers installed after this date.
    (2) Any storage container having a capacity of 2,000 gallons or less 
and installed prior to July 1, 1975, if such container is equipped with 
a permanent submerged fill pipe by May 31, 1977.
    (3) Transfer made to storage tanks equipped with floating roofs or 
their equivalent.
    (4) Storage containers installed after July 1, 1975 in Kings County.
    (5) Storage containers installed after January 1, 1975 in Madera 
County.
    (e) Compliance schedule:
    (1) June 1, 1974--Submit to the Administrator a final control plan, 
which describes at a minimum the steps that will be taken by the source 
to achieve compliance with the provisions of paragraph (c) of this 
section.
    (2) March 1, 1975--Negotiate and sign all necessary contracts for 
emission control systems, or issue orders for the purchase of component 
parts to accomplish emission control.

[[Page 180]]

    (3) May 1, 1975--Initiate on-site construction or installation of 
emission control equipment.
    (4) February 1, 1976--Complete on-site construction or installation 
of emission control equipment.
    (5) July 1, 1976--Assure final compliance with the provisions of 
paragraph (c) of this section.
    (6) Any owner or operator of sources subject to the compliance 
schedule in this paragraph shall certify to the Administrator, within 5 
days after the deadline for each increment of progress, whether or not 
the required increment of progress has been met.
    (f) Paragraph (e) of this section shall not apply:
    (1) To a source which is presently in compliance with the provisions 
of paragraph (c) of this section and which has certified such compliance 
to the Administrator by June 1, 1974. The Administrator may request 
whatever supporting information he considers necessary for proper 
certification.
    (2) To a source for which a compliance schedule is adopted by the 
State and approved by the Administrator.
    (3) To a source whose owner or operator submits to the 
Administrator, by June 1, 1974, a proposed alternative schedule. No such 
schedule may provide for compliance after March 1, 1976. If promulgated 
by the Administrator, such schedule shall satisfy the requirements of 
this section for the affected source.
    (g) Nothing in this section shall preclude the Administrator from 
promulgating a separate schedule for any source to which the application 
of the compliance schedule in paragraph (e) of this section fails to 
satisfy the requirements of Secs. 51.261 and 51.262(a) of this chapter.
    (h) Any gasoline-dispensing facility subject to this section that 
installs a storage tank after the effective date of this section shall 
comply with the requirements of paragraph (c) of this section by March 
1, 1976 and prior to that date shall comply with paragraph (e) of this 
section as far as possible. Any facility subject to this section that 
installs a storage tank after March 1, 1976, shall comply with the 
requirements of paragraph (c) of this section at the time of 
installation.
[38 FR 31251, Nov. 12, 1973]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.255, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.256  Control of evaporative losses from the filling of vehicular tanks.

    (a) ``Gasoline'' means any petroleum distillate having a Reid vapor 
pressure of 4 pounds or greater.
    (b) This section is applicable in the Metropolitan Los Angeles and 
Sacramento Valley Intrastate Air Quality Control Regions, except as 
follows:
    (1) In the following portions of the Metropolitan Los Angeles 
Intrastate Region, this section is rescinded.
    (i) South Coast AQMD.
    (ii) Santa Barbara County APCD.
    (2) In the following portions of the San Joaquin Valley Intrastate 
Region, this section is rescinded.
    (i) Kings County APCD.
    (3) In the following portion of the Sacramento Valley Intrastate 
Region, this section is rescinded.
    (i) Sacramento County APCD.
    (ii) El Dorado County APCD (Mountain Counties Air Basin portion).
    (iii) Placer County APCD (Mountain Counties Air Basin portion).
    (c) A person shall not transfer gasoline to an automotive fuel tank 
from a gasoline dispensing system unless the transfer is made through a 
fill nozzle designed to:
    (1) Prevent discharge of hydrocarbon vapors to the atmosphere from 
either the vehicle filler neck or dispensing nozzle;
    (2) Direct vapor displaced from the automotive fuel tank to a system 
wherein at least 90 percent by weight of the organic compounds in 
displaced vapors are recovered; and
    (3) Prevent automotive fuel tank overfills or spillage on fill 
nozzle disconnect.
    (d) The system referred to in paragraph (c) of this section can 
consist of a vapor-tight vapor return line from the fill nozzle/filler 
neck interface to the dispensing tank or to an adsorption, absorption, 
incineration, refrigeration-condensation system or its equivalent.

[[Page 181]]

    (e) Components of the systems required by paragraph (c) of 
Sec. 52.255 can be used for compliance with paragraph (c) of this 
section.
    (f) If it is demonstrated to the satisfaction of the Administrator 
that it is impractical to comply with the provisions of paragraph (c) of 
this section as a result of vehicle fill neck configuration, location, 
or other design features for a class of vehicles, the provisions of this 
paragraph shall not apply to such vehicles. However, in no case shall 
such configuration exempt any gasoline dispensing facility from 
installing and using in the most effective manner a system required by 
paragraph (c) of this section.
    (g) Compliance schedule:
    (1) January 1, 1975--Submit to the Administrator a final control 
plan, which describes at a minimum the steps that will be taken by the 
source to achieve compliance with the provisions of paragraph (c) of 
this section.
    (2) March 1, 1975--Negotiate and sign all necessary contracts for 
emission control systems, or issue orders for the purchase of component 
parts to accomplish emission control.
    (3) May 1, 1975--Initiate on-site construction or installation of 
emission control equipment. Compliance with the requirements of 
paragraph (c) of this section shall be as soon as practicable, but no 
later than specified in paragraphs (g) (4) and (5)of this section.
    (4) May 1, 1977--Complete on-site construction or installation of 
emission control equipment or process modification.
    (5) May 31, 1977--Assure final compliance with the provisions of 
paragraph (c) of this section.
    (6) Any owner or operator of sources subject to the compliance 
schedule in this paragraph (g) shall certify to the Administrator, 
within 5 days after the deadline for each increment of progress, whether 
or not the required increment of progress has been met.
    (h) Paragraph (g) of this section shall not apply:
    (1) To a source which is presently in compliance with the provisions 
of paragraph (c) of this section and which has certified such compliance 
to the Administrator by January 1, 1975. The Administrator may request 
whatever supporting information he considers necessary for proper 
certification.
    (2) To a source for which a compliance schedule is adopted by the 
State and approved by the Administrator.
    (3) To a source whose owner or operator submits to the 
Administrator, by June 1, 1974, a proposed alternative schedule. No such 
schedule may provide for compliance after May 31, 1977. If promulgated 
by the Administrator, such schedule shall satisfy the requirements of 
this section for the affected source.
    (i) Nothing in this section shall preclude the Administrator from 
promulgating a separate schedule for any source to which the application 
of the compliance schedule in paragraph (g) of this section fails to 
satisfy the requirements of Secs. 51.261 and 51.262(a) of this chapter.
    (j) Any gasoline dispensing facility subject to this section that 
installs a gasoline dispensing system after the effective date of this 
section shall comply with the requirements of paragraph (c) of this 
section by May 31, 1977, and prior to that date shall comply with 
paragraph (g) of this section as far as possible. Any facility subject 
to this section that installs a gasoline dispensing system after May 31, 
1977, shall comply with the requirements of paragraph (c) of this 
section at the time ofinstallation.
[38 FR 31251, Nov. 12, 1973, as amended at 39 FR 4881, Feb. 8, 1974; 39 
FR 21053, June 18, 1974; 46 FR 5979, Jan. 21, 1981; 46 FR 60203, Dec. 9, 
1981; 47 FR 19332, May 5, 1982; 47 FR 19698, May 7, 1982; 47 FR 28622, 
July 1, 1982; 47 FR 29538, July 7, 1982; 51 FR 40676, Nov. 7, 1986]

    Editorial Note: The compliance dates given in paragraphs (g) (1) 
through (3) were deferred indefinitely at 40 FR 1127, Jan. 6, 1975.



Secs. 52.257--52.262  [Reserved]



Sec. 52.263  Priority treatment for buses and carpools--Los Angeles Region.

    (a) Definitions: (1) ``Carpool'' means a vehicle containing three or 
more persons.
    (2) ``Bus/carpool lane'' means a lane on a street or highway open 
only to buses (or to buses and carpools), whether constructed especially 
for that purpose or converted from existing lanes.

[[Page 182]]

    (3) ``Preferential treatment'' for any class of vehicles, means 
either the setting aside of one traffic lane for the exclusive use of 
such vehicles or other measures (for example, access metering or setting 
aside the entire street), which the Administrator finds would be at 
least equal in VMT reduction effect to the establishment of such a lane.
    (b) This regulation is applicable in the Metropolitan Los Angeles 
Intrastate Air Quality Control Region (the ``Region'').
    (c) On or before May 31, 1974, the State of California, through the 
State Department of Transportation or through other agencies to which 
legal authority has been delegated, shall establish the following system 
of bus/carpool lanes.
    (1) Ventura/Hollywood Corridor--a concurrent flow exclusive bus/
carpool lane from Topanga Canyon Boulevard, Woodland Hills (U.S. 101) to 
junction of the Hollywood Freeway, and contraflow on the Hollywood 
Freeway (U.S. 101) from the junction with Ventura Freeway in North 
Hollywood to Vermont Avenue, and bus preferential treatment on arterial 
surface streets from Vermont Avenue to the Los Angeles central business 
district (CBD).
    (2) Harbor Freeway Corridor--contraflow on Harbor Freeway 
(California 11) from vicinity of Pacific Coast Highway, in Wilmington, 
to junction of Santa Monica Freeway (I-10), then by surface street 
preferential treatment to LA/CBD.
    (3) Wilshire Corridor--surface street preferential bus treatment 
from vicinity of San Vincente Boulevard, to LA/CBD.
    (4) San Bernardino Freeway Corridor-Bus/carpool lane, either 
contraflow, or concurrent flow on San Bernardino Freeway from El Monte 
terminus of existing San Bernardino Freeway bus lane (I-10), to vicinity 
of Ontario Airport.
    (5) Priority Treatment in CBD--provide preferential treatment in CBD 
on surface streets to connect Wilshire and San Bernardino corridors.
    (d) On or before May 31, 1976, the State of California, through the 
State Department of Transportation or other agencies to which legal 
authority has been delegated, shall establish the following system of 
bus and bus/carpool lanes:
    (1) Contraflow lane on the Golden State Freeway (I-5) from junction 
of Ventura Freeway (California 134) in Los Angeles to San Bernardino 
Freeway (I-10).
    (2) Contraflow on Pasadena Freeway (California 11) from terminus in 
City of Pasadena to Hollywood Freeway (U.S. 101).
    (3) Contraflow on Pomona Freeway from San Gabriel Freeway (I-605) to 
Santa Ana Freeway (I-5).
    (4) Concurrent flow in San Diego Freeway (I-405) from Ventura 
Freeway (U.S. 101) in Sherman Oaks to Newport Freeway (California 55), 
Costa Mesa.
    (5) Concurrent flow on Long Beach Freeway (California 7) from Santa 
Ana Freeway (I-5), City of Commerce to San Diego Freeway (I-405), Long 
Beach.
    (6) Artesia Freeway (California 91) from Santa Ana Freeway (I-5) to 
Long Beach Freeway (California 7), Long Beach.
    (e) State III will include specific routes in other portions of the 
Region.
    (f) On or before December 31, 1973, the State of California shall 
submit to the Administrator a compliance schedule showing the steps it 
will take to establish the system of bus/carpool lanes required by 
paragraphs (c) and (d) of this section, with each schedule to include 
the following:
    (1) A schedule for the establishment of the lanes. The schedule for 
the lanes required by paragraph (d) of this section shall provide for 
the first such lane to be set aside no later than June 1, 1974.
    (2) Bus/carpool lanes must be prominently indicated by overhead 
signs at appropriate intervals and at each intersection of entry ramps.
    (3) Bus/carpool lanes must be prominently indicated by distinctive 
painted, pylon, or physical barriers.
    (4) Vehicles using a bus/carpool lane shall have the right of way 
when crossing other portions of the road to enter or leave such lanes.
    (5) At a minimum, the bus/carpool lanes so set aside shall operate 
from 6:30 a.m. to 9:30 a.m. and from 3:30 to 6:30 a.m. each weekday.

[[Page 183]]

    (g) No deviation from the system of bus/carpool lanes required under 
paragraphs (c) and (d) of this section shall be permitted except upon 
application made by the State of California to the Administrator at the 
time of submittal of compliance schedules and approved by him, which 
application must contain a satisfactory designation of alternate routes 
for the establishment of such lanes.
[38 FR 31254, Nov. 12, 1973]



Secs. 52.264--52.268  [Reserved]



Sec. 52.269  Control strategy and regulations: Photochemical oxidants (hydrocarbons) and carbon monoxide.

    (a) The requirements of subpart G of this chapter are not met 
because the plan does not provide for attainment and maintenance of the 
national standards for photochemical oxidants (hydrocarbons) and carbon 
monoxide in the San Francisco Bay Area, San Diego, Sacramento Valley, 
San Joaquin Valley, and Southeast Desert Intrastate Regions by May 31, 
1975.
    (b) The following regulatory changes represent a relaxation of 
previously submitted regulations, and an adequate control strategy 
demonstration has not been submitted showing that the relaxation would 
not interfere with the attainment and maintenance of the national 
standards for photochemical oxidants.
    (1) Mountain Counties Intrastate Region.
    (i) Calaveras County APCD.
    (A) The revocation of Rule 412, Organic Liquid Loading, is 
disapproved. Rule 412 submitted on June 30, 1972 and previously approved 
in 40 CFR 52.223 is retained.
    (B) The revocation of Rule 413, Effluent Oil Water Separators, is 
disapproved; and Rule 413 submitted on June 30, 1972 and previously 
approved in 40 CFR 52.223 is retained.
    (ii) Tuolumne County APCD.
    (A) The revocation of Rule 413, Organic Liquid Loading, is 
disapproved; and Rule 413 submitted on June 30, 1972 and previously 
approved in 40 CFR 52.223 is retained.
    (B) The revocation of Rule 414, Effluent Oil Water Separators, is 
disapproved; and Rule 414 submitted on June 30, 1972 and previously 
approved in 40 CFR 52.223 is retained.
    (C) The revocation of Rule 413, Organic Liquid Loadings, submitted 
February 10, 1977, is disapproved; and the previously approved Rule 413 
submitted on June 30, 1972 remains in effect.
    (D) The revocation of Rule 414, Effluent Oil Water Separators, 
submitted on February 10, 1977, is disapproved; and the previously 
approved Rule 414 submitted on June 30, 1972, remains in effect.
    (1-1) San Joaquin Valley Intrastate Region.
    (i) Stanislaus County APCD.
    (A) Rule 411.1, submitted on November 4, 1977, is disapproved. Rule 
411.1 submitted on April 21, 1976 remains in effect.
    (ii) Merced County APCD.
    (A) Rule 411.1, submitted on November 4, 1977, is disapproved. Rule 
411.1, submitted on August 2, 1976, remains in effect.
    (iii) Fresno County APCD.
    (A) Rules 411.1, Gasoline Transfer Into Vehicle Fuel Tanks, 
submitted on November 4, 1977, is disapproved; and Rule 411.1 submitted 
on April 21, 1976, and previously approved under 40 CFR 52.223, is 
retained.
    (iv) Tulare County APCD.
    (A) Section 412.1, Transfer of Gasoline Into Vehicle Fuel Tanks, 
submitted on October 13, 1977, is disapproved; and Section 412.1, 
submitted on April 21, 1976, and previously approved under 40 CFR 
52.223, is retained.
    (v) Madera County APCD.
    (A) Rule 412.1, Transfer of Gasoline Into Stationary Storage 
Containers, submitted on October 13, 1977, is disapproved; and Rules 
411, Gasoline Storage and 411.1, Transfer of Gasoline Into Stationary 
Storage Containers, submitted on June 30, 1972, and April 10, 1976, 
respectively, and previously approved under 40 CFR 52.223 are retained.
    (vi) San Joaquin County APCD.
    (A) Rule 411.2, Transfer of Gasoline Into Vehicle Fuel Tanks, 
submitted on November 4, 1977, is disapproved; and rule 411.2, submitted 
on February 10, 1976 and previously approved under 40 CFR 52.223, is 
retained.
    (2) Sacramento Valley intrastate region:

[[Page 184]]

    (i) Sacramento County APCD.
    (A) Rule 13 submitted on November 4, 1977, is disapproved.
    (ii) Placer County APCD.
    (A) Rule 218, Architectural Coatings, adopted on May 20, 1985 and 
submitted to EPA on February 10, 1986 is disapproved. The version of 
this rule by the same number and title submitted on July 19, 1983 and 
approved by EPA on May 3, 1984 is retained.
    (iii) Sutter County APCD.
    (A) Rule 3.15, Architectural Coatings, adopted on October 15, 1985 
and submitted to EPA on February 10, 1986 is disapproved. The version of 
this rule by the same number and title submitted on January 1, 1981 and 
approved by EPA on May 3, 1982 is retained.
    (3) Southeast Desert Intrastate AQCR.
    (i) Los Angeles County APCD.
    (A) Regulation IV, rule 465, Vacuum Producing Devices or Systems, 
submitted on June 6, 1977, is disapproved. Rule 74 with the same title, 
submitted on June 6, 1977, is disapproved. Rule 69 with the same title, 
submitted on June 30, 1972 and approved under 40 CFR 52.223, is 
retained.
    (ii) Riverside County APCD.
    (A) Regulation IV, rule 465, Vacuum Producing Devices or Systems, 
submitted on June 6, 1977, is disapproved. Rule 74 with the same title, 
submitted on June 30, 1972 and approved under 40 CFR 52.223, is 
retained.
    (B) Rule 461, Gasoline Transfer and Dispensing, submitted November 
4, 1977, is disapproved. The version of this rule submitted on April 21, 
1977 (same number and title), which was previously approved in 40 CFR 
52.223, is retained.
    (4) Great Basin Valleys Intrastate Region.
    (i) Great Basin Unified APCD.
    (A) Rule 418 submitted on November 4, 1977, is disapproved. Rule 418 
submitted on April 21, 1976 remains in effect.
    (B) Rule 419, Gasoline Loading into Stationary Tanks, submitted on 
June 22, 1978, is disapproved, and rule 419, submitted April 21, 1976, 
and previously approved in 40 CFR 52.223, is retained.
    (c) The following rules and regulations are disapproved because they 
represent a relaxation of promulgated EPA regulations, and an adequate 
control strategy demonstration has not been submitted showing that the 
relaxation would not interfere with the attainment and maintenance of 
the national standrds for photochemical oxidants:
    (1) Sacramento Valley Intrastate AQCR.
    (i) Yolo-Solano APCD.
    (A) Rules 2.21(b)(1), 2.21(b)(2), 2.21(b)(4), 2.21(b)(5) and 
2.21(b)(6), submitted on June 6, 1977.
    (d) Imperial County APCD Rule 415, Gasoline Loading from Tank Trucks 
and Trailers, submitted by the State on November 4, 1977 is approved as 
applicable to facilities installed after July 1, 1977. District Rule 
125, Gasoline Loading into Tank Trucks and Trailers and Rule 129, 
Gasoline loading into Tanks, submitted on February 21, 1972 and 
previously approved under 40 CFR 52.223 are retained as part of the 
State implementation plan, as applicable to facilities installed prior 
to July 1, 1977.
    (e) The emission reduction credits for the following control 
measures contained in Ventura County's 1982 Ozone nonattainment area 
plan, submitted by the Governor's designee on December 31, 1982, are 
disapproved since the control measures are of an intermittent and 
voluntary nature and are therefore not approvable under Sections 
110(a)(2)(F)(v) and 123 of the Clean Air Act: R-38/N-16, ``No Use Day''; 
R-39/N-17, ``No Drive Day''; R-40, ``No Spray Day''; R-41/N-18 
``Stationary Source Curtailments.''
[38 FR 16564, June 22, 1973. Redesignated at 40 FR 3767, Jan. 24, 1975]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.269, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.270  Significant deterioration of air quality.

    (a) With the exception of the areas listed in paragraph (b) of this 
section:
    (1) The requirements of Sections 160 through 165 of the Clean Air 
Act are not met in California.
    (2) The plan does not include approvable procedures for preventing 
the significant deterioration of air quality.
    (3) The provisions of Sec. 52.21(b) through (w) are hereby 
incorporated and made a

[[Page 185]]

part of the applicable state plan for the State of California.
    (b) District PSD Plans. (1) The PSD rules for the Sacramento County 
Air Pollution Control District are approved under Part C, Subpart 1, of 
the Clean Air Act. However, EPA is retaining authority to apply 
Sec. 52.21 in certain cases. The provisions of Sec. 52.21 (b) through 
(w) are therefore incorporated and made a part of the state plan for 
California for the Sacramento County Air Pollution Control District for:
    (i) Those cogeneration and resource recovery projects which are 
major stationary sources or major modifications under Sec. 52.21 and 
which would cause violations of PSD increments.
    (ii) Those projects which are major stationary sources or major 
modifications under Sec. 52.21 and which would either have stacks taller 
than 65 meters or would use ``dispersion techniques'' as defined in 
Sec. 51.1.
    (iii) Sources for which EPA has issued permits under Sec. 52.21, 
including the following permit and any others for which applications are 
received by June 19, 1985.

    Procter & Gamble, SAC 83-01, 5/6/83.

    (2) The PSD rules for the North Coast Unified Air Quality Management 
District are approved under Part C, Subpart 1, of the Clean Air Act. 
However, EPA is retaining authority to apply Sec. 52.21 in certain 
cases. The provisions of Sec. 52.21 (b) through (w) are therefore 
incorporated and made a part of the state plan for California for the 
North Coast Unified Air Quality Management District for:
    (i) Those cogeneration and resource recovery projects which are 
major stationary sources or major modifications under Sec. 52.21 and 
which would cause violations of PSD increments.
    (ii) Those projects which are major stationary sources of major 
modifications under Sec. 52.21 and which would either have stacks taller 
than 65 meters or would use ``dispersion techniques'' as defined in 
Sec. 51.1.
    (iii) Sources for which EPA has issued permits under Sec. 52.21, 
including the following permits and any others for which applications 
are received by July 31, 1985;
    (A) Arcata Lumber Co. (NC 78-01; November 8, 1979),
    (B) Northcoast Paving (NC 79-03; July 5, 1979),
    (C) PG&E Buhne Pt. (NC 77-05).
    (3) The PSD rules for the Mendocino County Air Pollution Control 
District are approved under Part C, Subpart 1, of the Clean Air Act. 
However, EPA is retaining authority to apply Sec. 52.21 in certain 
cases. The provisions of Sec. 52.21 (b) through (w) are therefore 
incorporated and made a part of the state plan for California for the 
Mendocino County Air Pollution Control District for:
    (i) Those cogeneration and resource recovery projects which are 
major stationary sources or major modifications under Sec. 52.21 and 
which would cause violations of PSD increments.
    (ii) Those projects which are major stationary sources or major 
modifications under Sec. 52.21 and which would either have stacks taller 
than 65 meters or would use ``dispersion techniques'' as defined in 
Sec. 51.1.
    (iii) Any sources for which EPA has issued permits under Sec. 52.21, 
including any permits for which applications are received by July 31, 
1985.
    (4) The PSD rules for the Northern Sonoma County Air Pollution 
Control District are approved under Part C, Subpart 1, of the Clean Air 
Act. However, EPA is retaining authority to apply Sec. 52.21 in certain 
cases. The provisions of Sec. 52.21 (b) through (w) are therefore 
incorporated and made a part of the state plan for California for the 
Northern Sonoma County Air Pollution Control District for:
    (i) Those cogeneration and resource recovery projects which are 
major stationary sources or major modifications under Sec. 52.21 and 
which would cause violations of PSD increments.
    (ii) Those projects which are major stationary sources or major 
modifications under Sec. 52.21 and which would either have stacks taller 
than 65 meters or would use ``dispersion techniques'' as defined in 
Sec. 51.1.
    (iii) Any sources for which EPA has issued permits under Sec. 52.21, 
including any permits for which applications are received by July 31, 
1985.
[50 FR 25419, June 19, 1985, as amended at 50 FR 30943, July 31, 1985]

[[Page 186]]



Sec. 52.271  Malfunction regulations.

    (a) The following regulations are disapproved because they would 
permit the exemption of sources from the applicable emission limitations 
and therefore do not satisfy the enforcement imperatives of section 110 
of the Clean Air Act.
    (1) Amador County APCD.
    (i) Rule 404, submitted on April 21, 1976.
    (ii) Rule 4f, submitted on June 30, 1972, and previously approved 
under 40 CFR 52.223 (37 FR 19812).
    (2) Bay Area APCD.
    (i) Regulation 2, Section 3212, and Regulation 3, Section 3203, 
submitted on April 21, 1976.
    (ii) Regulation 2, Section 3212, submitted on February 21, 1972, and 
previously approved under 40 CFR 52.223 (37 FR 10842).
    (3) Calaveras County APCD.
    (i) Rules 110 and 402(f), submitted on July 25, 1973.
    (ii) Rule 404, submitted on October 13, 1977.
    (4) Colusa County APCD.
    (i) Rule 4.4g, submitted on July 25, 1973, and Rule 4.4g, submitted 
on June 30, 1972, and previously approved under 40 CFR 52.223 (37 FR 
19812).
    (5) Del Norte County APCD.
    (i) Rule 540, submitted on November 10, 1976.
    (ii) Rule 45, submitted on February 21, 1972, and previously 
approved under 40 CFR 52.223 (37 FR 10842).
    (6) Fresno County APCD.
    (i) Rule 110, submitted on June 30, 1972, and previously approved 
under 40 CFR 52.223.
    (ii) Rules 110 and 402(f), submitted on October 23, 1974.
    (7) Glenn County APCD.
    (i) Rules 95.2 and 95.3, submitted on January 10, 1975.
    (8) Great Basin Unified APCD.
    (i) Rule 403, submitted on June 6, 1977.
    (ii) Rule 617, submitted on November 4, 1977.
    (9) Humboldt County APCD.
    (i) Rule 540, Submitted on November, 10, 1976.
    (ii) Rule 59, Submitted on February 21, 1972 and previously approved 
under 40 CFR 52.223 (37 FR 10842).

    Editorial Note: At 46 FR 27118, May 18, 1981, the following 
paragraph (a)(9) was added to Sec. 52.271.

    (9) Monterey Bay Unified APCD.
    (i) Rule 214, submitted on March 4, 1980.
    (ii) Rule 617, submitted on May 23, 1979.
    (10) Kern County APCD.
    (i) Rule 111, submitted on July 19, 1974.
    (11) Kings County APDC.
    (i) Rule 111, submitted on July 25, 1973, and Rule 111, submitted on 
July 30, 1972, and previously approved under 40 CFR 52.223.
    (ii) Rule 111, submitted on November 4, 1977.
    (12) Lake County APCD.
    (i) Chapter III, Article I, Section 500, and Article II, Sections 
510 and 511, submitted on February 10, 1977.
    (ii) Part VI, Sections 1 and 2, submitted on June 30, 1972, and 
previously approved under 40 CFR 52.223.
    (13) Los Angeles County APCD.
    (i) Rule 430, submitted on June 6, 1977.
    (14) Madera County APCD.
    (i) Rule 402(f), submitted on January 10, 1975, and Rule 110, 
submitted on June 30, 1972, and previously approved under 40 CFR 52.223.
    (ii) Rule 110, submitted on January 10, 1975.
    (15) Mariposa County APCD.
    (i) Rule 203(j), submitted on January 10, 1975, and Rule 4.3(g), 
submitted on February 21, 1972, and previously approved under 40 CFR 
52.223.
    (ii) Rule 404, submitted on June 6, 1977.
    (16) Mendocino County APCD.
    (i) Rule 540, submitted on November 10, 1976.
    (ii) Sections 1 and 2 of Part VI, submitted on February 21, 1972, 
and previously approved under 40 CFR 52.223 (37 FR 10842).
    (17) Merced County APCD.
    (i) Rule 109, submitted on August 2, 1976.
    (ii) Rule 109, submitted on June 30, 1972, and previously approved 
under 40 CFR 52.223 (37 FR 19812).
    (18) Nevada County APCD.
    (i) Rule 55(f), submitted on February 21, 1972, and previously 
approved under 40 CFR 52.223 (37 FR 10842).

[[Page 187]]

    (19) Northern Sonoma County APCD.
    (i) Rule 540, submitted on November 10, 1976.
    (20) Placer County APCD.
    (i) Rule 55(f), submitted on February 21, 1972, and previously 
approved under 40 CFR 52.223 (37 FR 10842).
    (ii) Rule 404, submitted on October 13, 1977.
    (21) Plumas County APCD.
    (i) Rule 203(j), submitted on January 10, 1975.
    (ii) Rule 404, submitted on June 6, 1977.
    (22) Riverside County APCD.
    (i) Rule 430, submitted on June 6, 1977.
    (23) San Bernardino County APCD.
    (i) Rule 430, submitted on June 6, 1977.
    (ii) Rule 55, submitted on February 21, 1972, and previously 
approved under 40 CFR 52.223 (37 FR 10842).
    (24) San Joaquin County APCD.
    (i) Rule 110, submitted on October 23, 1974, and Rule 110, submitted 
on June 30, 1972, and previously approved under 40 CFR 52.223 (37 FR 
19812).
    (25) San Luis Obispo County APCD.
    (i) Rule 107, submitted on November 10, 1976.
    (ii) Rule 102, submitted on February 21, 1972, and previously 
approved under 40 CFR 52.223 (37 FR 10842).
    (26) Shasta County APCD.
    (i) Rule 3:10, submitted on July 19, 1974.
    (ii) Rule 3:10, submitted on June 30, 1972, and previously approved 
under 40 CFR 52.223 (37 FR 19812).
    (27) Sierra County APCD.
    (i) Rule 51, submitted on June 30, 1972, and previously approved 
under 40 CFR 52.223 (37 FR 19812), and Rule 203(j), submitted on January 
10, 1975, and previously approved under 40 CFR 52.223 (42 FR 23805).
    (ii) Rule 404, submitted on June 6, 1977.
    (28) Southern California APCD.
    (i) Rule 430, submitted on February 10, 1977.
    (29) Stanislaus County APCD.
    (i) Rule 110, submitted on June 30, 1972, and previously approved 
under 40 CFR 52.223 (37 FR 19812), and Rule 110, submitted on July 19, 
1974.
    (30) Tehama County APCD.
    (i) Rule 417, submitted on July 19, 1974.
    (ii) Rule 4:1g, submitted on June 30, 1972, and previously approved 
under 40 CFR 52.223 (37 FR 19812).
    (31) Trinity County APCD.
    (i) Rule 540, submitted on November 10, 1976.
    (ii) Rule 44, submitted on June 30, 1972, and previously approved 
under 40 CFR 52.223 (37 FR 19812).
    (32) Tulare County APCD.
    (i) Rules 111 and 402(f), submitted on November 10, 1976.
    (33) Tuolumne County APCD.
    (i) Rule 404, submitted on February 10, 1977, and Rule 402(f), 
submitted on June 30, 1972, and previously approved under 40 CFR 52.223.
    (34) Ventura County APCD.
    (i) Rule 32, submitted on July 19, 1974.
    (ii) Rule 32, submitted on June 30, 1972, and previously approved 
under 40 CFR 52.223 (37 FR 19812).
    (35) Yuba County APCD.
    (i) Rule 4.5, submitted on July 25, 1973.
    (b) The following regulations are disapproved since they lack 
explicit provisions to assure that that NAAQS will not be exceeded while 
equipment breakdown periods are in effect.
    (1) Fresno County APCD.
    (i) Rules 110(B), Variance Required, and 519, Emergency Variance, 
submitted on January 2, 1979.
    (2) Kern County APCD.
    (i) Rules 111 (b), (Equipment Breakdown), and 519, Emergency 
Variance, submitted on January 2, 1979.
    (3) Modoc County APCD.
    (i) Rule 2:15, Breakdown Conditions; Emergency Variances, submitted 
on May 7, 1979.
    (4) Imperial County APCD.
    (i) Rule 111 (B), Equipment Breakdown, submitted on December 24, 
1979.
    (ii) Rule 517, Emergency Variance, submitted on December 24, 1979.
[43 FR 3277, Jan. 24, 1978]


    Editorial Note: For Federal Register citations affecting 
Sec. 52.271, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.

[[Page 188]]



Sec. 52.272  Research operations exemptions.

    (a) The requirements of Sec. 51.281 of this chapter are not met 
because the following regulations allow exemptions to be granted from 
the applicable emission limitations, thereby potentially rendering the 
applicable limitations unenforceable. Furthermore, the regulations are 
inconsistent with the Clean Air Act, because the regulations could 
permit violations of the National Ambient Air Quality Standards under 
some circumstances. Therefore, the following regulations are 
disapproved:
    (1) Bay Area APCD.
    (i) Regulation 2, Division 1, sections 1214 to 1214.3, submitted on 
July 25, 1973.
    (ii) Regulation 3, Division 1, sections 1205 to 1205.3, submitted on 
July 25, 1973.
    (2) El Dorado County APCD.
    (i) Rule 203(D), submitted on November 4, 1977.
    (3) Great Basin Unified APCD.
    (i) Rule 423, submitted on November 4, 1977.
    (4) Los Angeles County APCD.
    (i) Rule 441, submitted on June 6, 1977.
    (5) Placer County APCD.
    (i) Rule 203(D), submitted on October 13, 1977.
    (6) Riverside County APCD.
    (i) Rule 441, submitted on June 6, 1977.
    (7) Sacramento County APCD.
    (i) Rule 30, submitted on January 22, 1974.
    (8) San Bernardino County APCD.
    (i) Rule 441, submitted on June 6, 1977.
    (9) Southern California APCD.
    (i) Rule 441, submitted on August 2, 1976.
[42 FR 42226, Aug. 22, 1977]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.272, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.273  Open burning.

    (a) The following rules or portions of rules are disapproved because 
they contain exemptions to open burning (including open agricultural 
burning) prohibitions, that do not satisfy the requirements of section 
110 of the Clean Air Act:
    (1) Amador County APCD.
    (i) Rules 308 and 312, submitted on April 21, 1976.
    (ii) Rule 304, submitted on October 13, 1977.
    (iii) Rules 302(G) and 322, submitted on October 15, 1979.
    (2) Calaveras County APCD.
    (i) Rules 304 and 322, submitted on October 13, 1977.
    (3) Del Norte County APCD.
    (i) Rule 410(c)(2) and the following portions of Regulation 2: 
General prohibitions (all of page 1), paragraph (f) of Article I, 
paragraphs (f) and (g) of Article V, and paragraph (f) of Article VI, 
submitted on November 10, 1976.
    (4) El Dorado County APCD.
    (i) Rules 302(C), 304, 307, 319, and 322, submitted on November 4, 
1977.
    (ii) Rules 302 (C), 318, and 321, submitted on May 23, 1979.
    (5) Fresno County APCD.
    (i) Rules 416.1(e)(1), (e)(3), and (e)(4), submitted on October 23, 
1974.
    (ii) Rule 416.1(c)(1), submitted on June 30, 1972, and previously 
approved under 40 CFR 52.223 (37 FR 19812).
    (6) Humboldt County APCD.
    (i) Rule 410(c)(2) and the following portions of Regulation 2: 
General prohibitions (all of page 1), paragraph (f) of Article I, 
paragraphs (f) and (g) of Article V, and paragraph (f) of Article VI, 
submitted on November 10, 1976.
    (ii) (A)-(C) [Reserved]
    (D) Rules 312 (B) and (C), and 401 (D.1) and (D.2).
    (7) Kern County APCD.
    (i) Rule 417(I)(A), submitted on November 10, 1976.
    (8) Madera County APCD.
    (i) Rules 416.1(e)(1), (e)(3), and (e)(4), submitted on January 10, 
1975.
    (ii) Rule 416.1(c)(1), submitted on June 30, 1972, and previously 
approved under 40 CFR 52.223 (37 FR 19812).
    (9) Mariposa County APCD.
    (i) Rules 302(C), 304, 319, and 322, submitted on June 6, 1977.
    (10) Mendocino County APCD.
    (i) Rule 410(c)(2) and the following portions of Regulation 2: 
General prohibitions (all of page 1), paragraph (f) of Article I, 
paragraphs (f) and (g) of Article V, and paragraph (f) of Article VI, 
submitted on November 10, 1976.

[[Page 189]]

    (11) Merced County APCD.
    (i) Rule 416(h), submitted on August 2, 1976.
    (ii) Rules 416.1(III)(A), (V)(A), (V)(B), (V)(C), and (V)(D), 
submitted on August 2, 1976. (Rule 416.1(c)(2), submitted on June 30, 
1972, and previously approved, is retained. Rule 416.1(a)(1), submitted 
on June 30, 1972, and previously approved, is retained for the purpose 
of enforcing Rule 416.1(c)(2).)
    (12) Monterey Bay Unified APCD.
    (i) Rules 409(a), 409(a)(5), and 410(b)(1), submitted on January 10, 
1975.
    (13) Nevada County APCD.
    (i) Rules 302(C), 307, 314, and 322, submitted on April 10, 1975.
    (ii) Rules 304 and 319, submitted on June 6, 1977.
    (iii) Rule 307, submitted on October 15, 1979.
    (14) Northern Sonoma County APCD.
    (i) Rule 410(c)(2) and the following portions of Regulation 2: 
General prohibitions (all of page 1), paragraph (f) of Article I, 
paragraphs (f) and (g) of Article V, and paragraph (f) of Article VI, 
submitted on November 10, 1976.
    (15) Placer County APCD.
    (i) Rules 302(C), 302(G), 304, 307, 314, 319, and 322, submitted on 
October 13, 1977.
    (ii) Rules 303, 306, and 322, submitted on October 15, 1979.
    (16) Plumas County APCD.
    (i) Rule 314, submitted on January 10, 1975.
    (ii) Rules 302(C), 304, 307, 319, and 322, submitted on June 6, 
1977.
    (17) Sacramento County APCD.
    (i) Rule 96(a), submitted on November 10, 1976.
    (ii) Rule 96(a), submitted on November 4, 1977.
    (18) San Joaquin County APCD.
    (i) Rule 402(e), submitted on November 10, 1976.
    (ii) Rule 416.1(c)(1), submitted on June 30, 1972, and previously 
approved under 40 CFR 52.223 (37 FR 19812).
    (iii) Rules 416.1(D)(1) and (D)(2), submitted on October 23, 1974.
    (19) Santa Barbara County APCD.
    (i) Rules 40(4)(a) and 40(4)(1), submitted on July 25, 1973. (The 
analogous Rules 40(4)(a) and 40(4)(g), previously approved in the 
February 21, 1972 submittal, are retained.) Rule 40(4)(c), submitted on 
July 25, 1973, is also disapproved.
    (ii) Rule 22, submitted on January 22, 1974. (The analogous Rule 22, 
previously approved in the February 21, 1972 submittal, is retained.) 
Rules 24.1 and 24.2, submitted on January 22, 1974, are also 
disapproved.
    (20) Shasta County APCD.
    (i) Rule 2:6, sections (1)(b)(iii) (a, b, and d), (1)(c)(viii), 
2(c), 3(f), 4(e), 5(c), and 5(d). (Previously approved Rule 2:6, 
sections (2)(c), (3)(f), and (4)(e), submitted on July 19, 1974, are 
retained.)
    (21) Sierra County APCD.
    (i) Rules 302(C), 319, and 322, submitted on June 6, 1977.
    (22) Trinity County APCD.
    (i) Rule 410(c)(2) and the following portions of Regulation 2: 
General prohibitions (all of page 1), paragraph (f) of Article I, 
paragraphs (f) and (g) of Article V, and paragraph (f) of Article VI, 
submitted on November 10, 1976.
    (23) Tulare County APCD.
    (i) Rule 402(e), submitted on November 10, 1976.
    (ii) Section 417(III)(A), submitted on June 30, 1972, and previously 
approved under 40 CFR 52.223 (37 FR 19812).
    (iii) Section 417.1(e)(1), (e)(3), and (e)(4), submitted on January 
10, 1975.
    (24) Tuolumne County APCD.
    (i) Rule 322, submitted on February 10, 1977.
    (25) Yolo-Solano APCD.
    (i) Rules 2.8(c) (4) and (5), 6.3, and 6.5(a), submitted on July 25, 
1973.
    (ii) Rules 6.1(a), (e)(6), and (g), submitted on January 10, 1975. 
(Rules 4.1 (a) and (g), submitted on February 21, 1972, and previously 
approved under 40 CFR 52.223, are retained.)
    (b) The following rules or portions of rules are disapproved because 
they relax the control on open burning (including agricultural burning) 
without accompanying analyses demonstrating that these relaxations will 
not interfere with the attainment and maintenance of the National 
Ambient Air Quality Standards:
    (1) Del Norte County APCD.
    (i) Regulation 2, Article I, paragraph (e), submitted on November 
10, 1976.
    (ii) Rule 410(c)(2), submitted on May 7, 1979.
    (2) Fresno County APCD.

[[Page 190]]

    (i) Rule 416.1(c)(1), submitted on October 23, 1974.
    (ii) Rule 416.1(g), submitted on November 4, 1977.
    (3) Humboldt County APCD.
    (i) Regulation 2, Article I, paragraph (e), submitted on November 
10, 1976.
    (ii) Rule 410(c)(2), submitted on May 7, 1979.
    (4) Imperial County APCD.
    (i) Rule 422, submitted on November 4, 1977. (The requirements of 
Rule 115, submitted on February 21, 1972, and previously approved under 
40 CFR 52.223, are retained as applicable to the burning of wood waste.)
    (ii) Regulation VII (Rules 701 to 706), submitted on November 4, 
1977. (Regulation VII (Rules 200 to 206), submitted on July 25, 1973 and 
previously approved under 40 CFR 52.223, is retained.)
    (5) Kings County APCD.
    (i) Rules 416.1 and 417.1, submitted on November 4, 1977.
    (6) Lake County APCD.
    (i) Sections 435, 436, 1003, and 1200(A), submitted on February 10, 
1977.
    (ii) Section 435, submitted on January 2, 1979.
    (7) Los Angeles County APCD.
    (i) Rule 444, submitted on June 6, 1977. (Rules 57.1, 57.2, 57.3, 
and 57.4, submitted on June 30, 1972, and previously approved under 40 
CFR 52.223, are retained.)
    (8) Madera County APCD.
    (i) Rule 416.1(c)(1), submitted on January 10, 1975.
    (9) Mendocino County APCD.
    (i) Regulation 2, Article I, paragraph (e), submitted on November 
10, 1976.
    (ii) Rule 410(c)(2), submitted on May 7, 1979.
    (10) Merced County APCD.
    (i) Rule 416.1(I)(A)(2), submitted on August 2, 1976.
    (11) Northern Sonoma County APCD.
    (i) Regulation 2, Article I, paragraph (e), submitted on November 
10, 1976.
    (ii) Rule 410(c)(2), submitted on May 7, 1979.
    (12) San Bernardino County Desert APCD.
    (i) Rule 444 and the definition of ``Agricultural Burning'' in Rule 
102, submitted on November 4, 1977. (Rule 57, submitted on February 21, 
1972, and previously approved under 40 CFR 52.223, is retained.)
    (13) San Diego County APCD.
    (i) Rules 102(e) and 103(g), submitted on October 13, 1977.
    (14) San Luis Obispo County APCD.
    (i) Rule 501(B), submitted on November 10, 1976, and Rule 501(A)(7), 
submitted on November 4, 1977. (Previously approved Rule 115(2), 
submitted on February 21, 1972, is retained.)
    (15) Santa Barbara County APCD.
    (i) Rules 2(b), 40(3), and 40(4)(e), submitted on July 25, 1973. 
(Analogous Rules 2(b), 40(3), and 40(4)(c), submitted on February 21, 
1972, and previously approved, are retained.)
    (16) Shasta County APCD.
    (i) Rule 2:8, submitted on October 13, 1977. (Rule 2:8, submitted on 
July 19, 1974, and July 22, 1975, and previously approved, is retained.)
    (17) Siskiyou County APCD.
    (i) Rule 4.3(2), submitted on January 2, 1979.
    (18) Trinity County APCD.
    (i) Regulation 2, Article I, paragraph (e), submitted on November 
10, 1976.
    (ii) Rule 410(c)(2), submitted on May 7, 1979.
    (19) Placer County APCD.
    (i) Rule 316, submitted on August 21, 1979.
    (ii) Rules 318 and 323, submitted on October 15, 1979.
[42 FR 41122, Aug. 15, 1977]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.273, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.274  California air pollution emergency plan.

    (a) Since the California Air Pollution Emergency Plan does not 
provide complete, implementable provisions for taking emission control 
actions necessary to prevent ambient pollutant concentrations from 
reaching significant harm levels, the requirements of subpart H of this 
chapter for Priority I and II areas are not met, except in the following 
areas:
    (1) South Coast Air Quality Management District (SCAQMD).
    (2) Sacramento County Air Pollution Control District.
    (3) Monterey Bay Unified APCD (MBUAPCD).

[[Page 191]]

    (4) Santa Barbara Air Quality Management Area portion of the Santa 
Barbara County Air Pollution Control District.
    (5) Bay Area Air Quality Management District.
    (6) Ventura County Air Pollution Control District.
    (7) San Diego County APCD.
    (8) Los Angeles County Air Pollution Control District.
    (9) Riverside County Air Pollution Control District.
    (10) San Bernardino County Desert Air Pollution Control District.
    (11) Imperial County Air Pollution Control District.
    (12) Fresno County Air Pollution Control District.
    (13) Kern County Air Pollution Control District.
    (b) The requirements of subpart H of this chapter are met in the 
SCAQMD with the following exceptions: SCAQMD Regulation VII has no 
schedule to assure that the emission control actions are fully 
implementable; does not provide specific emission control actions for 
interdistrict coordination; has no provisions for nitrogen dioxide, 
particulate matter, and sulfur dioxide and particulate matter combined 
episodes; has no criteria or provisions to protect the eight-hour 
averaged carbon monoxide significant harm level; and has no provisions 
for implementation of abatement plans for stage 2 or 3 carbon monoxide 
or oxidant episodes that are attained without being predicted.
    (c) Regulation for prevention of air pollution emergency episodes--
plan scheduling, interdistrict coordination, episode criteria, and 
declaration.
    (1) The requirements of this paragraph are applicable in the SCAQMD.
    (2) The owner or operator of any governmental, industrial, business, 
or commercial activity listed in Rules 708.1 and 708.3 of Regulation VII 
of the SCAQMD, as revised on May 6, 1977, shall submit a Stationary 
Source Curtailment Plan and/or Traffic Abatement Plan to the 
Administrator within sixty days after the effective date of this 
paragraph.
    (3) The plans submitted pursuant to the requirements of this 
paragraph, shall be reviewed by the Administrator for approval or 
disapproval according to the following schedule:
    (i) For sources with emissions of hydrocarbons (HC) or nitrogen 
oxides (NOx) greater than or equal to 454 metric tons (500 
tons) per year, or for establishments employing 400 or more employees 
per shift, within 45 days after receipt.
    (ii) For sources with emissions of HC or NOx greater than 
or equal to 91 metric tons (100 tons) per year and less than 454 metric 
tons (500 tons) per year, or for establishments employing more than 200 
and less than 400 employees per shift, within 90 days after receipt.
    (iii) For sources or establishments other than those addressed in 
paragraphs (c)(3) (i) through (ii) of this section, within 180 days 
after receipt.
    (4) The owner or operator of an industrial, business, governmental 
or commercial establishment required to submit a plan by this paragraph 
shall be notified by the Administrator within thirty days after the plan 
has been evaluated if the plan is disapproved. Any plan disapproved by 
the Administrator shall be modified to overcome the disapproval and 
resubmitted to the Administrator within 30 days of the receipt of the 
notice of disapproval.
    (5) In the event specific sources or source areas within the SCAQMD 
are determined to significantly contribute to a declared air pollution 
episode in a nearby Air Pollution Control District, emission control 
actions specified in Regulation VII of the SCAQMD, as revised on May 6, 
1977, for that declared episode stage shall be taken in the SCAQMD to 
abate that episode.
    (6) For the purposes of this paragraph, the following episode 
criteria shall apply to carbon monoxide concentrations averaged over 
eight hours:
    (i) For stage 1, 15 parts per million.
    (ii) For stage 2, 30 parts per million.
    (iii) For stage 3, 40 parts per million.
    (7) The provisions of SCAQMD Regulation VII, as revised on May 6, 
1977, relating to carbon monoxide episodes averaged over 12 hours shall 
apply to carbon monoxide episodes averaged over 8 hours except that the 
Administrator shall provide for declaration, notification, source 
inspections, and termination of the episodes.

[[Page 192]]

    (8) Whenever the Administrator has determined that the stage 2 or 3 
episode level for oxidant or carbon monoxide as specified in Rule 703 of 
Regulation VII of the SCAQMD, as amended May 6, 1977, is being attained 
or has been attained, and is predicted to remain at such level for 12 or 
more hours, or increase, or in the case of oxidant to reoccur within the 
next 24 hours, unless control actions are taken, the existence of the 
appropriate episode level and the location of the source-receptor areas 
shall be declared, and the actions specified in Rules 710(b)(1), 
710(b)(2), 711(b)(1), or 711(b)(2) shall be taken by the Administrator.
    (d) Regulation for prevention of air pollution emergency episodes--
nitrogen dioxide, particulate matter, and sulfur dioxide and particulate 
matter combined.
    (1) The requirements of this paragraph are applicable in the SCAQMD.
    (2) For the purposes of this regulation the following definitions 
apply:
    (i) ``Ppm'' means parts per million by volume.
    (ii) ``COH'' means coefficient of haze.
    (iii) ``Ugm3'' means micrograms per cubic meter.
    (iv) ``Administrator'' means the Administrator of the Environmental 
Protection Agency or his authorized representative.
    (v) ``Major National Holiday'' means a holiday such as Christmas, 
New Year's Day, or Independence Day.
    (vi) ``Source/Receptor Areas'' are defined for each episode 
occurrence based on air monitoring, geographical, and meteorological 
factors: Source area is that area in which contaminants are discharged 
and a receptor area is that area in which the contaminants accumulate 
and are measured.
    (vii) ``Air Contaminants'' means nitrogen dioxide, particulate 
matter, and/or sulfur dioxide and particulate matter combined.
    (3) For the purposes of this regulation, the following episode 
criteria shall apply:

----------------------------------------------------------------------------------------------------------------
                                     Averaging
           Contaminants                time            Stage 1               Stage 2               Stage 3
                                      (hours)
----------------------------------------------------------------------------------------------------------------
Nitrogen dioxide..................           1  0.6 ppm.............  1.2 ppm.............  1.6 ppm.
                                            24  0.15 ppm............  0.3 ppm.............  0.4 ppm.
Particulate matter................          24  3.0 COH.............  5.0 COH.............  7.0 COH.
                                            24  375 ugm-3...........  625 ugm-3...........  875 ugm-3.
Sulfur dioxide and particulate              24  0.2\1\..............  0.8\1\..............  1.2\1\.
 matter combined.
                                            24  65,000\2\...........  261,000\2\..........  393,000\2\.
----------------------------------------------------------------------------------------------------------------
\1\ Product of sulfur dioxide (ppm) and particulate matter (COH).
\2\ Product of sulfur dioxide (ugm-3 ) and particulate matter (ugm-3 ).

    (4) Whenever the Administrator has determined that any episode level 
specified in paragraph (d)(3) of this section is being attained or has 
been attained, and is predicted to remain at such level for 12 or more 
hours, or increase, unless control actions are taken, the existence of 
the appropriate episode level and the location of the source-receptor 
areas shall be declared.
    (5) Whenever the available scientific and meteorological data 
indicate that any episode level declared by paragraph (d)(4) of this 
section is no longer occurring and is not predicted to immediately 
increase again to episode levels, such episode shall be declared 
terminated.
    (6) The following shall be notified by the Administrator whenever an 
episode is predicted, attained or terminated: (i) Public officials; (ii) 
persons operating any facility or activity named in paragraph (d)(8) of 
this section; (iii) public health, safety, and emergency agencies; (iv) 
news media.
    (7) Upon request of the Administrator, persons operating any 
facility or activity named in paragraph (d)(8) of this section shall 
install, properly maintain, and operate radio-receiving equipment with 
decoding device capable of receiving broadcasts of the declaration and 
termination of episodes required under this paragraph and instructions 
as to the actions to be taken.
    (8) Stationary source curtailment plans and traffic abatement plans 
shall be prepared by industrial, business,

[[Page 193]]

commercial, and governmental establishments as follows:
    (i) The owner or operator of any industrial, business, commercial, 
or governmental activity listed below shall submit to the Administrator 
plans to curtail operations causing stationary source air contaminants 
in such activity:
    (A) Petroleum refinery emitting 23 metric tons (25 tons) or more per 
year of air contaminants.
    (B) Metal-melting plant requiring molten metal temperatures in 
excess of 540 deg. C (1,000 deg. F) or metal-refining plant or metal-
smelting plant, in which a total of 1,135 kilograms (2,500 pounds) or 
more of metal are in a molten state at any one time or are poured in any 
1 hour.
    (C) Fossil fuel-fired electric generating facility having a total 
rated capacity of 50 megawatts or more.
    (D) Any facility or plant emitting 91 metric tons (100 tons) or more 
per year of air contaminants.
    (ii) The plans required by paragraph (d)(8)(i) of this section shall 
include the following:
    (A) A list of equipment which emits nitrogen oxides, particulate 
matter, and/or sulfur dioxide, including the SCAQMD permit number, the 
daily amount of air contaminants emitted, and a statement of the minimum 
time and recommended time to implement the abatement actions for each 
episode stage for the equipment listed and the percent reduction in 
emissions at each episode stage.
    (B) The total number of employees at the facility during each shift 
on a normal weekday and on a major national holiday.
    (C) The normal amount of electricity used on a normal weekday and on 
a major national holiday.
    (D) The actions to inform employees of the procedures to be taken in 
the event of an episode declaration.
    (E) The name and telephone numbers of the facility's episode action 
coordinator and alternate, who are responsible for implementation of the 
plan.
    (F) For stage 1 episodes:
    (1) The measures to voluntarily curtail equipment emitting air 
contaminants.
    (2) The measures to curtail or postpone electrically intensive 
industrial operations, where feasible.
    (3) The measures for electric utilities to import power from outside 
the basin to the extent feasible.
    (G) For stage 2 episodes:
    (1) The measures to curtail as much as possible, without upsetting 
production, equipment operations which emit air contaminants.
    (2) The measures to postpone operations which can be postponed until 
after the episode.
    (3) For fossil fuel-fired combustion sources, including electric 
utilities, with a heat input greater than 50 million BTU per hour:
    (i) The measures to burn natural gas.
    (ii) To the extent that natural gas is not available, the measures 
to burn fuel oil with a sulfur content of not more than 0.25 percent by 
weight or the measures to reduce air contaminant emissions to equivalent 
discharge. Any combustion source may be exempt from the provisions of 
this paragraph upon demonstration that fuel oil with the specified 
sulfur content is not available.
    (4) For electric utilities the measures, in addition to those in 
paragraph (d)(8)(ii)(F)(3) of this section, to:
    (i) Shift oil burning power generation to non-source areas to the 
maximum extent consistent with the public health, safety, and welfare.
    (ii) Shift oil burning power generation to combined cycle gas 
turbine generating equipment burning fuel oil containing less than 0.15 
percent sulfur to the maximum extent consistent with the public health, 
safety, and welfare.
    (5) For refineries and chemical plants the measures to be taken to 
reduce air contaminant emissions by 20 percent without jeopardizing the 
public health or safety, without causing an increase in the emissions of 
other air contaminants, withoutdamaging the equipment or without 
reducing production by more than 20 percent.
    (6) The measures in paragraph (d)(8)(ii)(F) of this section.
    (H) For stage 3 nitrogen dioxide episodes:
    (1) The measures for petroleum refineries to reduce emissions of 
nitrogen

[[Page 194]]

dioxide by 33 percent, without damaging the equipment or increasing the 
emissions of other air contaminants.
    (2) The measures in paragraph (d)(8)(ii)(G) of this section.
    (3) A list of equipment and the permit numbers of such equipment not 
operated on a major national holiday.
    (4) A statement as to whether or not the facility operates on a 
major national holiday.
    (I) For stage 3 particulate matter episodes:
    (1) The measures for petroleum refineries to reduce emissions of 
particulate matter by 33 percent, without damaging the equipment or 
increasing the emissions of other air contaminants.
    (2) The measures described in paragraph (d)(8)(ii)(G) of this 
section.
    (3) The measures for any facility or plant, except electrical 
generating facilities and petroleum refineries, normally emitting 91 
metric tons (100 tons) or more per year of particulate matter to 
eliminate such emissions by starting no new batches, by ceasing feed of 
new materials, and by phasing down as rapidly as possible without damage 
to the equipment.
    (4) The measures for metal melting, refining, or smelting plants to 
eliminate emissions of particulate matter by starting no new batches, by 
ceasing feed of new materials, and by phasing down as rapidly as 
possible without damage to the equipmen
    (J) For stage 3 sulfur dioxide and particulate matter combined 
episodes:
    (1) The measures described in paragraphs (d)(8)(ii) (G) and (I) of 
this section.
    (2) The measures for petroleum refineries to reduce emissions of 
sulfur dioxide by 33 percent, without damaging the equipment or 
increasing the emissions of other air contaminants.
    (3) The measures for any facility or plant, except electrical 
generating facilities and petroleum refineries, normally emitting 91 
metric tons (100 tons) or more per year of sulfur dioxide to eliminate 
such emissions by starting no new batches, by ceasing feed of new 
materials, and by phasing down as rapidly as possible without damage to 
the equipment.
    (K) An estimate of the resultant reduction in air contaminant 
emissions.
    (iii) The owner or operator of any industrial, business, commercial, 
or governmental activity listed below shall submit to the Administrator 
plans to curtail or cease operations causing air contaminants from 
vehicle use:
    (A) Operators of 50 or more fleet vehicles.
    (B) Industrial, business, commercial, or governmental establishments 
employing more than 100 persons per shift at one business address.
    (iv) The plans required by paragraph (d)(8)(iii) of this paragraph 
shall include the following:
    (A) The total number of employees at the facility during each shift 
on a normal weekday and on a major national holiday.
    (B) The number of motor vehicles and vehicle miles traveled for 
motor vehicles operated:
    (1) By the company on company business on a normal weekday and on a 
major national holiday.
    (2) By employees commuting from home to the place of business on a 
normal weekday and on a major national holiday.
    (C) The number of parking spaces used on a normal weekday and on a 
major national holiday.
    (D) The minimum number of motor vehicles to be operated that are 
necessary to protect public health or safety.
    (E) The actions to inform employees of the procedures to be taken in 
the event of an episode declaration.
    (F) The name and telephone numbers of the facility's episode action 
coordinator and alternate, who are responsible for implementation of the 
plan.
    (G) For stage 1 episodes, the methods by which employers will 
encourage the utilization of car pools or otherwise reduce employee 
motor vehicle travel.
    (H) For stage 2 and 3 episodes, the measures within the reasonable 
control of the employer to reduce the number of vehicle miles driven by 
employees in commuting to and from work.
    (I) An estimate of the reduction in vehicle miles traveled as a 
result of the measures in this paragraph.
    (v) Each owner or operator required to submit a plan by this 
paragraph shall submit to the Administrator such

[[Page 195]]

plan within 60 days of the effective date of this paragraph.
    (vi) The plans submitted in accordance with the provisions of this 
paragraph shall be approved or disapproved by the Administrator 
according to the following schedule:
    (A) For sources with emissions of air contaminants greater than or 
equal to 454 metric tons (500 tons) per year, or for establishments 
employing 400 or more employees per shift, within 45 days after receipt.
    (B) For sources with emissions of air contaminants greater than or 
equal to 91 metric tons (100 tons) per year and less than 454 metric 
tons (500 tons) per year, or for establishments employing more than 200 
and less than 400 employees per shift, within 90 days after receipt.
    (C) For sources with emissions of air contaminants less than 91 
metric tons (100 tons) per year, or for establishments employing 100 to 
200 employees per shift, within 180 days after receipt.
    (vii) The owner or operator required to submit a plan by this 
paragraph shall be notified by the Administrator within 30 days after 
the plan has been evaluated if the plan is disapproved. Any plan 
disapproved by the Administrator shall be modified to
    (viii) A copy of the plan approved in accordance with the provisions 
of this paragraph shall be on file and readily available on the premises 
to any person authorized to enforce the provisions of this section.
    (9) The following actions shall be taken in the source and receptor 
areas upon declaration of a stage 1 episode:
    (i) The notifications required by paragraph (d)(6) of this section.
    (ii) The Administrator shall advise the public that those 
individuals with special health problems should follow the precautions 
recommended by their physicians and health officials.
    (iii) The Administrator shall advise school officials to cancel, 
postpone, or reschedule programs which require outdoor physical 
activity.
    (iv) The Administrator shall request the public to stop all 
unnecessary driving.
    (v) The Administrator shall request the public to operate all 
privately owned vehicles on a pool basis.
    (vi) Persons operating any facility or activity named in paragraph 
(d)(8) of this section shall implement the appropriate plans specified 
in paragraph (8) for the declared stage 1 episode and air 
contaminant(s).
    (10) The following actions shall be taken in the source and receptor 
areas upon declaration of a stage 2 episode:
    (i) The actions described in paragraphs (d)(9) (i) through (v) of 
this section.
    (ii) The Administrator shall request suspension of programs that 
involve physical exertion by participants using public parks or public 
recreational facilities located in receptor areas.
    (iii) The burning of combustible refuse shall be postponed until the 
episode has been terminated.
    (iv) The Administrator shall request the public to reduce the use of 
electricity by 10 percent.
    (v) Persons operating any facility or activity named in paragraph 
(d)(8) of this section shall implement the appropriate plans specified 
in paragraph (d)(8) of this section for the declared stage 2 episode and 
air contaminant(s).
    (11) The following actions shall be taken in the source and receptor 
areas upon declaration of a stage 3 episode:
    (i) The actions described in paragraphs (d)(10) (i) through (iii) of 
this section.
    (ii) The Administrator shall request the public to reduce the use of 
electricity by 40 percent.
    (iii) Persons operating any facility or activity named in paragraph 
(d)(8) of this section shall implement the appropriate plans specified 
in paragraph (d)(8) of this section for the declared stage 3 episode and 
air contaminant(s).
    (iv) For nitrogen dioxide, the general public, schools, industrial, 
business, commercial, and governmental activities throughout the 
District shall operate as though the day were a major national holiday.
    (v) For particulate matter and/or sulfur dioxide and particulate 
matter combined, the Administrator shall request the public to reduce as 
much as possible activities causing dust emissions including 
agricultural operations,

[[Page 196]]

off-road vehicle use, anddriving on unpaved roads. Construction and 
demolition operation shall be postponed until the episode has been 
terminated.
    (12) In the event specific sources or source areas within the SCAQMD 
are determined to significantly contribute to a declared air pollution 
episode in a nearby Air Pollution Control District, emission control 
actions specified in this paragraph for that declared episode stage 
shall be taken in the SCAQMD to abate that episode.
    (13) A source inspection plan shall be implemented by the 
Administrator upon the declaration of any episode stage.
    (14) The Administrator shall provide for daily acquisition of 
forecasts of atmospheric stagnation conditions during any episode stage 
and updating of such forecasts at least every 12 hours.
    (15) Any source that violates any requirement of this section shall 
be subject to enforcement action under section 113 of the Act.
    (16) All submittals or notifications required to be submitted to the 
Administrator by this section shall be sent to:

Environmental Protection Agency, Air and Hazardous Materials Division 
(A-4), Attn: Air Programs Branch, 215 Fremont Street, San Francisco, 
Calif. 94105.

    (e) The requirements of subpart H of this chapter are met in the 
Sacramento County Air Pollution Control District with the following 
exceptions: There are no episode criteria levels, declaration 
procedures, notification procedures, source inspections, emission 
control actions or episode termination procedures for carbon monoxide 
episodes based on 4- and 8-hour averaging times; communication 
procedures for transmitting status reports and orders as to emission 
control actions to be taken during an episode stage are not provided 
for; there are no provisions for the inspection of those sources covered 
under Rule 122; there is no time schedule for the Air Pollution Control 
Officer to initiate the call for the submittal of individual abatement 
plans; the requirements for the content of the abatement plans are not 
sufficiently specific to ensure that adequate plans are submitted; no 
provisions exist for the daily acquisition of atmospheric stagnation 
conditions; a Priority II particulate matter episode contingency plan is 
not provided for in the regulation.
    (f) Regulation for prevention of air pollution emergency episodes--
4- and 8-hour carbon monoxide criteria levels, public announcement, 
source inspections, preplanned abatement strategies, acquisition of 
atmospheric stagnation forecasts.
    (1) The requirements of this paragraph are applicable in the 
Sacramento County Air Pollution Control District.
    (2) For the purposes of this regulation the following definitions 
apply:
    (i) ``Administrator'' means the Administrator of the Environmental 
Protection Agency or his authorized representative.
    (ii) ``ppm'' means parts per million by volume.
    (iii) ``ug/m3 '' means micrograms per cubic meter.
    (3) For the purposes of this paragraph, the following episode 
criteria shall apply:

------------------------------------------------------------------------
                                       Averaging
              Pollutant                   time     Stage   Stage   Stage
                                        (hours)      1       2       3
------------------------------------------------------------------------
Carbon monoxide......................         4   \1\ 25  \1\ 45  \1\ 60
                                              8   \1\ 15  \1\ 30  \1\ 40
------------------------------------------------------------------------
\1\ Parts per million by volume.

    (4) The provisions of the Sacramento County Air Pollution Control 
District's Regulation IX, as submitted on November 4, 1977, relating to 
carbon monoxide episodes averaged over 1 hour shall apply to carbon 
monoxide episodes averaged over 4 and 8 hours except that the 
Administrator shall insure that declaration, notification, source 
inspections, and termination of such episodes will occur.
    (5) Stationary source curtailment plans shall be prepared by 
business, commercial, industrial, and governmental establishments as 
follows:
    (i) The owner or operator of any business, commercial, industrial, 
or governmental facility or activity listed below shall submit to the 
Administrator plans to curtail or cease operations causing stationary 
source air contaminants in such activity:
    (A) Stationary sources which can be expected to emit 100 tons or 
more per

[[Page 197]]

year of hydrocarbons or carbon monoxide.
    (ii) The plans required by paragraph (f)(5)(i)(A) of this section 
shall include the following information:
    (A) The information requested by Regulation IX, Rule 125, section d, 
as submitted to the EPA on November 4, 1977.
    (B) The total number of employees at the facility during each shift 
on a normal weekday.
    (C) The amount of energy (gas, fuel oil, and electricity) used on a 
normal weekday.
    (D) For first-stage episodes, the measures to voluntarily curtail 
equipment emitting air pollutants.
    (E) For second-stage episodes:
    (1) The measures to curtail, as much as possible, equipment 
operations that emit air pollutants specific to the type of episode and, 
in the case of oxidant episodes, the equipment operations that emit 
hydrocarbons.
    (2) The measures to postpone operations which can be postponed until 
after the episode.
    (F) For third-stage episodes:
    (1) A list of equipment, with permit numbers if applicable, which 
can be shut down without jeopardizing the public health or safety, and 
an estimate of the resultant reductions in air contaminant emissions.
    (2) A list of all equipment, with permit numbers if applicable, 
which must be operated to protect the public health or safety, and an 
estimate of the air contaminant emissions from such equipment.
    (iii) Copies of the stationary source curtailment plans approved in 
accordance with the provisions of this paragraph shall be on file and 
readily available on the premises to any person authorized to enforce 
the provisions of this paragraph.
    (6) The owner or operator of any governmental, business, commercial, 
or industrial activity or facility listed in paragraph (f)(5) of this 
section shall submit a stationary source curtailment plan to the 
Administrator within 60 days after promulgation of final rulemaking.
    (7) The plans submitted pursuant to the requirements of this 
paragraph shall be reviewed by the Administrator for approval or 
disapproval according to the following schedule:
    (i) For sources with emissions of hydrocarbons and carbon monoxide 
greater than or equal to 454 metric tons (500 tons) per year, within 45 
days after receipt.
    (ii) For sources with emissions of hydrocarbons and carbon monoxide 
greater than or equal to 91 metric tons (100 tons) per year and less 
than 454 metric tons (500 tons) per year, within 90 days after receipt.
    (iii) For sources with emissions of hydrocarbons and carbon monoxide 
less than 91 metric tons (100 tons) per year, within 180 days after 
receipt.
    (8) The owner or operator of any industrial, business, governmental, 
or commercial establishment required to submit a plan by this paragraph 
shall be notified by the Administrator within 30 days after the plan has 
been evaluated. Any plan disapproved by the Administrator shall be 
modified to overcome the disapproval and resubmitted to the 
Administrator within 30 days of receipt of the notice of disapproval.
    (9) A source inspection plan shall be implemented by the 
Administrator upon the declaration of any episode stage, and the 
following facilities shall be inspected to ensure compliance:
    (i) Those sources covered under Rule 122, as submitted to the EPA on 
November 4, 1977, as appropriate.
    (10) The Administrator shall insure that forecasts of atmospheric 
stagnation conditions during any episode stage and updating of such 
forecasts are acquired.
    (11) Any source that violates any requirement of this regulation 
shall be subject to enforcement action under section 113 of the Clean 
Air Act.
    (12) All submittals or notifications required to be submitted to the 
Administrator by this regulation shall be sent to: Regional 
Administrator, Attn: Air and Hazardous Materials Division, Air Technical 
Branch, Technical Analysis Section (A-4-3) Environmental Protection 
Agency, 215 Fremont Street, San Francisco, CA 94105.
    (g) Regulation for the prevention of air pollution emergency 
episodes--Priority II particulate matter emergency episode contingency 
plan.

[[Page 198]]

    (1) The requirements of this paragraph are applicable in the 
Sacramento County Air Pollution Control District.
    (2) For the purposes of this paragraph the following episode 
criteria shall apply:

------------------------------------------------------------------------
                                       Averaging
              Pollutant                   time     Stage   Stage   Stage
                                        (hours)      1       2       3
------------------------------------------------------------------------
Particulate matter...................        24   \1\ 37
                                                       5  \1\ 62
                                                               5  \1\ 87
                                                                       5
------------------------------------------------------------------------
\1\ Micrograms per cubic meter.

    (3) Whenever it is determined that any episode level specified in 
paragraph (g)(2) of this section is predicted to be attained, is being 
attained, or has been attained and is expected to remain at such levels 
for 12 or more hours, the appropriate episode level shall be declared.
    (4) Whenever the available scientific and meteorological data 
indicate that any episode level specified in paragraph (g)(2) of this 
section is no longer being attained and is not predicted to increase 
again to episode levels, such episode shall be declared terminated.
    (5) The following shall be notified whenever an episode is 
predicted, attained, or terminated:
    (i) Public officials.
    (ii) Public health, safety, and emergency agencies.
    (iii) News media.
    (h) The requirements of Subpart H of this chapter are met in the 
MBUAPCD which the following exceptions: There is no time schedule to 
assure that stationary source and traffic curtailment plans are 
submitted and reviewed in a timely manner; curtailment plans are not 
sufficiently specific; there are no provisions for the acquisition of 
forecasts of atmospheric stagnation conditions; and adequate mandatory 
emission control actions are not specified for Third-Stage oxidant 
episodes.
    (i) Regulation for prevention of oxidant air pollution emergency 
episodes within the MBUAPCD.
    (1) The requirements of this paragraph are applicable in the 
MBUAPCD.
    (2) For the purposes of this regulation the following definitions 
apply:
    (i) ``Administrator'' means the Administrator of the Environmental 
Protection Agency or his authorized representative.
    (ii) ``Major national holiday'' means a holiday such as Christmas, 
New Year's Day or Independence Day.
    (iii) ``Regulation VII'' in this paragraph means Regulation VII, 
``Emergencies'', of the MBUAPCD, adopted May 25, 1977, and submitted to 
the Environmental Protection Agency as a revision to the California 
State Implementation Plan by the California Air Resources Board on 
November 4, 1977.
    (3) The plans required by Rule 705(a) of Regulation VII shall 
include the following information in addition to that required in Rule 
705(b) of Regulation VII, and shall be submitted and processed as 
follows:
    (i) Stationary sources.
    (A) The total number of employees at the facility during each shift:
    (1) On a normal weekday.
    (2) On a major national holiday.
    (B) The amount and type of fuel used:
    (1) On a normal weekday.
    (2) On a major national holiday.
    (C) For Third-Stage episodes:
    (1) A list of equipment and the permit numbers of such equipment not 
operated on a major national holiday.
    (2) A statement as to whether or not the facility operates on a 
major national holiday.
    (ii) Indirect sources.
    (A) The total number of employees at the facility during each shift:
    (1) On a normal weekday.
    (2) On a major national holiday.
    (B) The number of motor vehicles and vehicle miles traveled for 
motor vehicles operated:
    (1) By the company, on company business, on a normal weekday and on 
a major national holiday.
    (2) By employees commuting between home and the place of business on 
a normal weekday and on a major national holiday.
    (C) The number of parking spaces:
    (1) Available.
    (2) Normally used on a weekday.
    (3) Normally used on a major national holiday.
    (D) The minimum number of motor vehicles to be operated that are 
necessary to protect the public health or safety.
    (E) For Third-Stage episodes, a statement as to whether or not the 
facility operates on a major national holiday.

[[Page 199]]

    (iii) Each owner or operator required to submit a plan as specified 
under Rule 705(a) of Regulation VII shall submit such plans within 60 
days after promulgation of the final rulemaking.
    (iv) The plans submitted in accordance with the provisions of this 
paragraph shall be approved or disapproved by the Administrator within 
120 days after receipt.
    (v) Each owner or operator required to submit a plan as specified 
under Rule 705(a) of Regulation VII shall be notified within 90 days 
after the Administrator's decision.
    (vi) Any plan disapproved by the Administrator shall be modified to 
overcome this disapproval and resubmitted to the Administrator within 30 
days of the notice of disapproval.
    (vii) A copy of the plan approved in accordance with the provisions 
of this paragraph shall be on file and readily available on the premises 
to any person authorized to enforce the provisions of this section.
    (4) The following actions shall be implemented by the Administrator 
upon declaration of a Third-Stage oxidant episode: the general public, 
schools, industrial, business, commercial, and governmental activities 
throughout the MBUAPCD shall operate as though the day were a major 
national holiday.
    (5) The Administrator shall ensure the acquisition of forecasts of 
atmospheric stagnation conditions during any episode stage and updating 
of such forecasts.
    (j)-(o) [Reserved]
    (p) Regulation for prevention of air pollution emergency episodes--
requirements for stationary source curtailment plans and particulate 
matter episodes.
    (1) The requirements of this paragraph are applicable in the Los 
Angeles County, Riverside County, San Bernardino County Desert and 
Imperial County Air Pollution Control Districts.
    (2) For the purposes of this regulation, the following definitions 
apply:
    (i) ``Administrator'' means the Administrator of the Environmental 
Protection Agency or his authorized representative.
    (ii) ``ug/m\3\'' means micrograms per cubic meter.
    (iii) ``Major national holiday'' means a holiday such as Christmas 
or New Year's Day.
    (3) Stationary source curtailment plans shall be prepared by major 
stationary sources, as defined by section 169(1) of the Act:
    (i) The plans required by this paragraph shall include the following 
information:
    (A) The information requested in the California Air Resources 
Board's Criteria for Approval of Air Pollution Emergency Abatement Plans 
(Executive Order G-63).
    (B) The total number of employees at the facility during each work 
shift on a normal weekday and on a major national holiday.
    (C) The amount of energy (gas, fuel oil, and electricity) used on a 
normal weekday and on a major national holiday.
    (D) For first-stage episodes:
    (1) The measures to voluntarily curtail equipment emitting air 
pollutants.
    (E) For second-stage episodes:
    (1) The measures to curtail, as much as possible, equipment 
operations that emit air pollutants specific to the type of episode and, 
in the case of oxidant episodes, the equipment operations that emit 
hydrocarbons and nitrogen oxides.
    (2) The measures to postpone operations which can be postponed until 
after the episode.
    (F) For third-stage episodes:
    (1) A list of equipment, with permit numbers if applicable, which 
can be shut down without jeopardizing the public health or safety, and 
an estimate of the resultant reductions in hydrocarbons, nitrogen 
oxides, and particulate matter emissions.
    (2) A list of all equipment, with permit numbers if applicable, 
which must be operated to protect the public health or safety, and an 
estimate of the hydrocarbons, nitrogen oxides and particulate matter 
emissions from such equipment.
    (4) A copy of the stationary source curtailment plan approved in 
accordance with the provisions of this paragraph shall be on file and 
readily available on the premises to any person authorized to enforce 
the provisions of this paragraph.

[[Page 200]]

    (5) The owner or operator of any governmental, business, commercial, 
or industrial activity or facility listed in paragraph (p)(3) of this 
section shall submit a stationary source curtailment plan to the 
Administrator within 60 days after promulgation of final rulemaking.
    (6) The plans submitted pursuant to the requirements of this 
paragraph shall be reviewed by the Administrator within 90 days.
    (7) The owner or operator of any major stationary source required to 
submit a plan by this paragraph shall be notified by the Administrator 
within 30 days after the plan has been evaluated as to whether the plan 
has been approved or disapproved. Any plan disapproved by the 
Administrator shall be modified to overcome the disapproval and 
resubmitted to the Administrator within 30 days of receipt of the notice 
of disapproval.
    (8) All submittals or notifications required to be submitted to the 
Administrator by this regulation shall be sent to:

Regional Administrator, Attn: Air and Hazardous Materials Division, Air 
Technical Branch, Technical Analysis Section (A-4-3), Environmental 
Protection Agency, 215 Fremont Street, San Francisco CA 94105.

    (9) Any source that violates any requirement of this regulation 
shall be subject to enforcement action under section 113 of the Act.
    (10) For the purposes of this regulation the following episode 
criteria shall apply to particulate matter episodes:

------------------------------------------------------------------------
                                                      g/m\3\
                                       Averaging -----------------------
              Pollutant                   time     Stage   Stage   Stage
                                        (hours)      1       2       3
------------------------------------------------------------------------
Particulate matter...................        24      375     625     875
------------------------------------------------------------------------

    (q) The requirements of Subpart H of this chapter are met in the 
Fresno County Air Pollution Control District, with the following 
exceptions: There are no episode criteria levels, declaration 
procedures, notification procedures, source inspection procedures, 
emission control actions, or episode termination procedures for carbon 
monoxide episodes based on 4- and 8-hour averaging times, or for 
particulate matter emergency episodes based on 24-hour averaging times; 
there is no time schedule to initiate the call for the submittal of 
individual abatement plans; the requirements for the content of the 
abatement plans are not sufficiently specific to ensure the adequate 
plans are submitted; there are no provisions for requiring abatement 
plans from operations which attract large numbers of motor vehicles with 
their related emissions; the Stage 3 photochemical oxidants (ozone) 
criterion level equals the Federal significant harm level; there are no 
provisions for adequate mandatory emission control actions.
    (r) Regulation for prevention of air pollution emergency episodes--
4- and 8-hour carbon monoxide criteria levels, mandatory emission 
control actions, preplanned abatement strategies, and a Priority I 
particulate matter emergency episode contingency plan.
    (1) The requirements of this paragraph are applicable in the Fresno 
County Air Pollution Control District.
    (2) For the purposes of this regulation the following definitions 
apply:
    (i) ``Administrator'' means the Administrator of the Environmental 
Protection Agency or his authorized representative.
    (ii) ``ppm'' means parts per million by volume.
    (iii) ``g/m3'' means micrograms per cubic meter.
    (iv) ``Major national holiday'' means a holiday such as Christmas or 
New Year's Day.
    (3) For the purposes of this regulation, the following episode 
criteria shall apply to carbon monoxide episodes:

------------------------------------------------------------------------
                                       Averaging   Stage   Stage   Stage
              Pollutant                   time       1       2       3
                                        (hours)    (ppm)   (ppm)   (ppm)
------------------------------------------------------------------------
Carbon monoxide......................         4       25      45      60
                                              8       15      30      40
------------------------------------------------------------------------

    (4) The provisions of the Fresno County Air Pollution Control 
District's Regulation VI, as submitted on October 23, 1974, relating to 
carbon monoxide episodes averaged over 1 hour

[[Page 201]]

shall apply to carbon monoxide episodes averaged over 4 and 8 hours 
except that the Administrator shall insure that declaration procedures, 
notification procedures, source inspections, and termination of such 
episodes occur.
    (5) Stationary source curtailment plans and traffic abatement plans 
shall be prepared by business, commercial, industrial, and governmental 
establishments in Fresno County as follows:
    (i) The owner or operator of any business, commercial, industrial, 
or governmental stationary source which can be expected to emit 100 tons 
or more per year of carbon monoxide, hydrocarbons, or particulate matter 
shall submit to the Administrator plans to curtail or cease operations 
causing stationary source air contaminants in such activity:
    (ii) The plans required by paragraph (r)(5)(i) of this section shall 
include the following information:
    (A) The information requested in the California Air Resources 
Board's ``Criteria for Approval of Air Pollution Emergency Abatement 
Plans'' (Executive Order G-63).
    (B) The total number of employees at the facility during each shift 
on a normal weekday and on a major national holiday.
    (C) The amount of energy (gas, fuel oil, and electricity) used on a 
normal weekday and on a major national holiday.
    (D) For first-stage episodes, the measures to voluntarily curtail 
equipment emitting air pollutants.
    (E) For second-stage episodes:
    (1) The measures to curtail, as much as possible, equipment 
operations that emit air pollutants specific to the type of episode and, 
in the case of oxidant episodes, the equipment operations that emit 
hydrocarbons or nitrogen oxides.
    (2) The measures to postpone operations which can be postponed until 
after the episode.
    (F) For third-stage episodes:
    (1) A list of equipment, with permit numbers if applicable, which 
can be shut down without jeopardizing the public health or safety, and 
an estimate of the resultant reductions in carbon monoxide, 
hydrocarbons, nitrogen oxides, and particulate matter emissions.
    (2) A list of all equipment, with permit numbers if applicable, 
which must be operated to protect the public health or safety, and an 
estimate of the carbon monoxide, hydrocarbons, nitrogen oxides, and 
particulate matter emissions from such equipment.
    (iii) The owner or operator of any industrial, business, commercial, 
or governmental facility or activity employing more than 100 persons per 
shift at any one business address shall submit to the Administrator 
plans to curtail or cease operations causing air contaminants from 
vehicle use.
    (iv) The plans required by paragraph (r)(5)(iii) of this section 
shall include the following information:
    (A) The information requested in the California Air Resources 
Board's ``Criteria for Approval of Air Pollution Emergency Abatement 
Plans'' (Executive Order G-63).
    (B) The total number of employees at the facility during each shift.
    (C) The total number of motor vehicles and vehicle miles traveled 
for motor vehicles operated:
    (1) By the company on company business on a normal weekday and a 
major national holdiay.
    (2) By employees commuting between home and the place of business on 
a normal weekday and a major national holiday.
    (3) The minimum number of motor vehicles to be operated that are 
necessary to protect public health or safety.
    (6) A copy of the stationary source curtailment and/or traffic 
abatement plans approved in accordance with the provisions of this 
paragraph shall be on file and readily available on the premises to any 
person authorized to enforce the provisions of this paragraph.
    (7) The owner or operator of any governmental, business, commercial, 
or industrial activity or facility listed in paragraph (r)(5) of this 
section shall submit a stationary source curtailment plan and/or traffic 
abatement plan to the Administrator within 60 days after promulgation of 
final rulemaking.
    (8) The plans submitted pursuant to the requirements of this 
paragraph shall be reviewed by the Administrator

[[Page 202]]

for approval or disapproval according to the following schedule:
    (i) For sources with emissions of hydrocarbons, carbon monoxide, or 
particulate matter greater than or equal to 454 metric tons (500 tons) 
per year, or for establishments employing 400 or more employees per 
shift, within 45 days after receipt.
    (ii) For sources with emissions of hydrocarbons, carbon monoxide, or 
particulate matter greater than or equal to 91 metric tons (100 tons) 
per year and less than 454 metric tons (500 tons) per year, or for 
establishments employing more than 200 and less than 400 employees per 
shift, within 90 days after receipt.
    (iii) For establishments employing 100 to 200 employees per shift, 
within 180 days after receipt.
    (9) The owner or operator of any industrial, business, governmental 
or commercial establishment required to submit a plan by this paragraph 
shall be notified by the Administrator within 30 days after the plan has 
been evaluated as to whether the plan has been approved or disapproved. 
Any plan disapproved by the Administrator shall be modified to overcome 
the disapproval and resubmitted to the Administrator within 30 days of 
receipt of the notice of disapproval.
    (10) Any source that violates any requirement of this regulation 
shall be subject to enforcement action under section 113 of the Act.
    (11) All submittals or notifications required to be submitted to the 
Administrator by this regulation shall be sent to:

    Regional Administrator, ATTN: Air and Hazardous Materials Division, 
Air Technical Branch, Technical Analysis Section (A-4-3), Environmental 
Protection Agency, 215 Fremont Street, San Franscisco, CA 94105.

    (12) For the purposes of this regulation the following episode 
criteria shall apply to particulate matter episodes and Stage 3 
photochemical oxidants episodes:

------------------------------------------------------------------------
                                                      g/m\3\
                                       Averaging -----------------------
              Pollutant                   time     Stage   Stage   Stage
                                        (hours)      1       2       3
------------------------------------------------------------------------
Particulate matter...................        24      375     625     875
Photochemical oxidants...............         1   ......  ......  \1\ 0.
                                                                       5
------------------------------------------------------------------------
\1\ Parts per million.

    (13) The Fresno County Air Pollution Control District's Regulation 
VI, as submitted on October 23, 1974, relating to episodes for carbon 
monoxide and photochemical oxidants averaged over 1 hour, shall apply to 
particular matter episodes averaged over 24 hours, except that the 
Administrator shall insure that declaration procedures, notification 
procedures, source inspections, and termination of such episodes occur.
    (14) The Administrator shall insure that the following actions will 
be taken in the source and receptor areas on the declaration of a Stage 
1, Stage 2 or Stage 3 episode:
    (i) For a Stage 1 or Stage 2 episode:
    (A) Persons operating any facility or activity named in paragraph 
(r)(5) of this section shall implement the appropriate plans submitted 
in accordance with subparagraph (5) of the declared Stage 1 or Stage 2 
episode for the appropriate air contaminant(s).
    (ii) For a Stage 3 episode:
    (A) The general public, schools, industrial, business, commercial, 
and governmental activities throughout Fresno County shall operate as 
though the day were a major national holiday.
[43 FR 22721, May 26, 1978]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.274, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.275  Particulate matter control.

    (a) The following rules or portions of rules are retained because 
they control emissions of particulate matter, and because there is no 
demonstration that their deletion would not interfere with the 
attainment and maintenance of the national standards for particulate 
matter:
    (1) Lake County APCD.
    (i) Part III-50 and Part V-1B, submitted on October 23, 1974, and 
previously approved under 40 CFR 52.223.
    (2) San Luis Obispo County APCD.
    (i) Rule 113, submitted on February 21, 1972, and previously 
approved under 40 CFR 52.223.
    (b) The following regulations are disapproved because they relax the 
control on particulate matter emissions without any accompanying 
analyses demonstrating that these relaxations will not interfere with 
the attainment

[[Page 203]]

and maintenance of the National Ambient Air Quality Standards.
    (1) Amador County APCD.
    (i) Rules 211 and 212, submitted on April 21, 1976. (Regulation V, 
Rules 13 and 14, submitted on June 30, 1972, and previously approved, 
are retained.)
    (ii) Rules 207 and 212, submitted on October 13, 1977. (The 
analogous Rules 10 and 14 of Regulation V, submitted on June 30, 1972, 
and previously approved, are retained and shall remain in effect for 
Federal enforcement purposes.)
    (2) Calaveras County APCD.
    (i) Rule 211, submitted on October 13, 1977. (Rule 211, submitted on 
July 22, 1975, and previously approved, is retained and shall remain in 
effect for Federal enforcement purposes.)
    (3) Del Norte County APCD.
    (i) Rules 410(c)(7) and 420(e), submitted on November 10, 1976.
    (ii) Rules 420(e) and (f), submitted on November 4, 1977.
    (4) El Dorado County APCD.
    (i) Rule 212, submitted on April 10, 1975, and Rule 211, submitted 
on August 2, 1976. (The analogous Rule 55, submitted on February 21, 
1972, and previously approved, is retained and shall remain in effect 
for Federal enforcement purposes.)
    (5) Humbolt County APCD.
    (i) Rules 410(c)(7) and 420(e), submitted on November 10, 1976.
    (ii) Rules 420(e) and (f), submitted on November 4, 1977.
    (6) Mariposa County APCD.
    (i) Rule 211, submitted on June 6, 1977. (Rule 211, submitted on 
January 10, 1975, and previously approved, is retained and shall remain 
in effect for Federal enforcement purposes.)
    (7) Mendocino County APCD.
    (i) Rule 410(c)(7), submitted on November 10, 1976.
    (ii) Rules 420(e) and (f), submitted on November 4, 1977.
    (8) Nevada County APCD.
    (i) Rule 212, submitted on April 10, 1975, and Rule 211, submitted 
on April 21, 1976. (Rule 52.1, submitted on June 30, 1972, and 
previously approved, is retained and shall remain in effect for Federal 
enforcement purposes.)
    (9) Northern Sonoma County APCD.
    (i) Rule 420(e), submitted on November 10, 1976.
    (ii) Rules 420(e) and (f), submitted on October 13, 1977.
    (10) Placer County APCD.
    (i) Rule 211, submitted on October 13, 1977. (The analogous Rule 61, 
submitted on June 30, 1972, and previously approved, is retained and 
shall remain in effect for Federal enforcement purposes.)
    (ii) Rules 202, 207, and 211, submitted on October 15, 1979; and 
Section 61, and Rules 202 and 207, previously approved in the June 30, 
1972, January 10, 1975, and October 13, 1977 submittals, are retained.
    (11) Plumas County APCD.
    (i) Rule 211, submitted on June 6, 1977. (The analogous Rule 211, 
submitted on January 10, 1975, and previously approved, is retained and 
shall remain in effect for Federal enforcement purposes.)
    (12) San Luis Obispo County APCD.
    (i) Rule 403, submitted on November 10, 1976.
    (13) Sierra County APCD.
    (i) Rule 211, submitted on June 6, 1977. (The analogous Rule 211, 
submitted on January 10, 1975, and previously approved, is retained and 
shall remain in effect for Federal enforcement purposes.)
    (14) Trinity County APCD.
    (i) Rules 410(c)(7) and 420(e), submitted on November 10, 1976.
    (ii) Rules 420(e) and (f), submitted on November 4, 1977.
[43 FR 25675, June 14, 1978]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.275, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.276  Sulfur content of fuels.

    (a) The following rules or portions of rules are disapproved since 
they represent a relaxation of previously submitted regulations and an 
adequate control strategy demonstration has not been submitted showing 
that the relaxation will not interfere with the attainment and 
maintenance of the National Ambient Air Quality Standards:
    (1) North Central Coast Intrastate Region:
    (i) Monterey Bay Unified APCD.
    (A) Rule 412(a)(8), Sulfur Content of Fuels, submitted on October 
23, 1974.

[[Page 204]]

    (b) The deletion of the following rules from the State 
implementation plan is disapproved since their deletion represents a 
relaxation of the control strategy, and an adequate demonstration 
showing that the relaxation will not interfere with the attainment and 
maintenance of the national ambient air quality standards has not been 
submitted:
    (1) Southeast Desert Intrastate Region:
    (i) Imperial County APCD.
    (A) Rule 126, Sulfur Contents of Fuels, submitted on June 30, 1972 
and previously approved under 40 CFR 52.223.
[42 FR 56606, Oct. 27, 1977, as amended at 43 FR 35695, Aug. 11, 1978]



Sec. 52.277  Oxides of nitrogen, combustion gas concentration limitations.

    (a) The following rules are being retained to the extent that the 
new rules are less stringent than the previously approved rules:
    (1) North Central Coast Intrastate Region:
    (i) Monterey Bay Unified APCD.
    (A) Rule 404(c) submitted on February 21, 1972 by the Monterey-Santa 
Cruz Unified APCD and previously approved as part of the SIP, is being 
retained for sources combusting gaseous fuels. Rule 404(c) will be in 
effect for Monterey and Santa Cruz Counties only. Rule 404(c), submitted 
on November 10, 1976 by the Monterey Bay Unified APCD, will only be in 
effect for sources combusting liquid or solid fuels with heat input 
rates greater than 1\1/2\ billion BTU per hour in the Monterey and Santa 
Cruz portions of the Unified APCD.
    (B) Rule 408(b), submitted on February 21, 1972 by the San Benito 
County APCD and previously approved as part of the SIP, is being 
retained for sources combusting liquid, solid, or gaseous fuels with 
heat input rates less than 1\1/2\ billion BTU per hour. Rule 408(b) will 
be in effect for San Benito County only. Rule 404(c), submitted on 
November 10, 1976 by the Monterey Bay unified APCD, will only be in 
effect for sources combusting liquid, solid, or gaseous fuels with heat 
input rates greater than 1\1/2\ billion BTU per hour in the San Benito 
County portion of the Unified APCD.
[42 FR 56606, Oct. 27, 1977]



Sec. 52.278  Oxides of nitrogen control.

    (a) The following regulations are disapproved because they relax the 
control of nitrogen oxides emissions without an accompanying analysis 
demonstrating that this relaxation will not interfere with the 
attainment and maintenance of the National Ambient Air Quality 
Standards.
    (1) South central coast intrastate AQCR.
    (i) San Luis Obispo County APCD.
    (A) Rule 405(A)(1), Nitrogen Oxides Emission Standards Limitations 
and Prohibitions submitted on November 10, 1976, is disapproved; and 
Rule 114(4), Gaseous Contaminants Oxides of Nitrogen submitted on 
February 21, 1972 and previously approved in 40 CFR 52.223, is retained.
[43 FR 34467, Aug. 4, 1978]



Sec. 52.279  Food processing facilities.

    (a) The following regulations are disapproved because they conflict 
with the requirements of 40 CFR Subpart I [formerly Sec. 51.18], 
``Review of new sources and modifications,'' and relax the control on 
emissions from food processing facilities without any accompanying 
analyses demonstrating that these relaxations will not interfere with 
the attainment and maintenance of the National Ambient Air Quality 
Standards.
    (1) Merced County APCD Rules 210.1-II-J, 210.1-VII-F, 408-C (new 
sentences two and three), adopted on August 21, 1984, and submitted on 
October 5, 1984.
    (2) Bay Area Air Quality Management District sections 2-2-119, 2-2-
120. Adopted on September 19, 1984, and submitted on October 5, 1984.
[52 FR 3646, Feb. 5, 1987, as amended at 55 FR 31835, Aug. 6, 1990]



Sec. 52.280  Fuel burning equipment.

    (a) The following rules and regulations are disapproved because they 
relax the control on emissions from fuel burning equipment without any 
accompanying analyses demonstrating

[[Page 205]]

that these relaxations will not interfere with the attainment and 
maintenance of the National Ambient Air Quality Standards.
    (1) Mountain Counties Intrastate AQCR:
    (i) Amador County APCD.
    (A) Rules 209, submitted on April 21, 1976 and October 15, 1979, are 
disapproved; and Regulation V, Rule 19, previously approved in the June 
30, 1972 submittal, is retained.
    (B) Rule 210(B)(1), submitted on October 15, 1979, is disapproved; 
and Rules 11 and 210, previously approved in the June 30, 1972 and April 
21, 1976 submittals, are retained.
    (ii) Calaveras County APCD.
    (A) Rule 209, Fossil Fuel-Steam Generator Facility, submitted on 
October 13, 1977, is disapproved; and Rule 408, Fuel Burning Equipment, 
previously approved in the June 30, 1972, submittal, is retained and 
shall remain in effect for Federal enforcement purposes.
    (iii) Tuolumne County APCD.
    (A) Rule 210, submitted on October 15, 1979, is disapproved; and 
Rule 407, previously approved in the June 30, 1972 submittal, is 
retained.
    (iv) Placer County APCD.
    (A) Rule 210, submitted on October 15, 1979, is disapproved, and 
Rule 210, previously approved in the October 13, 1977 submittal, is 
retained.
    (2) Sacramento Valley Intrastate AQCR:
    (i) Yolo-Solano APCD.
    (A) Rule 2.16, Fuel Burning Heat or Power Generators, submitted on 
July 19, 1974 is disapproved; and Rule 2.16, Fuel Burning Equipment, 
submitted on June 30, 1972 and previously approved as part of the SIP in 
40 CFR 52.223, is retained.
    (3) Southeast Desert Intrastate AQCR.
    (i) San Bernardino County Desert APCD.
    (A) Rule 474, Fuel Burning Equipment--Oxides of Nitrogen, submitted 
November 4, 1977, is disapproved. Rule 68 (same title) submitted June 
30, 1972 and approved in 40 CFR 52.223 is retained.
    (b) The deletion of the following rules or portions of rules from 
the State implementation plan is disapproved since their deletion 
represents a relaxation of the control strategy and an adequate 
demonstration showing that the relaxation will not interfere with the 
attainment and maintenance of the national ambient air quality standards 
has not been submitted:
    (1) Southeast Desert Intrastate Region:
    (i) Imperial County APCD.
    (A) Rule 131, Fuel Burning Equipment, submitted on February 21, 1972 
and previously approved under 40 CFR 52.223.
    (ii) San Bernardino County.
    (A) Rule 67, Fuel Burning Equipment as applied to new sources. The 
emission limit of Rule 67 is retained and is applicable only to existing 
sources already granted a permit.
    (c) The emission limits of Rules 67 and 72 are partially retained, 
applicable only to (existing) sources granted permits prior to June 17, 
1981.
    (1) South Coast Air Quality Management District.
    (i) Rules 67, Fuel Burning Equipment, and 72, Fuel Burning 
Equipment, submitted on November 19, 1979.
[43 FR 25677, 25684 June 14, 1978, as amended at 43 FR 35696, Aug. 11, 
1978; 43 FR 51774, Nov. 7, 1978; 43 FR 59490, Dec. 21, 1978; 44 FR 5664, 
Jan. 29, 1979; 46 FR 3889, Jan. 16, 1981; 46 FR 27116, 27118, May 18, 
1981; 47 FR 25016, June 9, 1982]



Sec. 52.281  Visibility protection.

    (a) The requirements of section 169A of the Clean Air Act are not 
met, because the plan does not include approvable procedures for 
protection of visibility in mandatory Class I Federal areas.
    (b) Regulations for visibility monitoring. The provisions of 
Sec. 52.26 are hereby incorporated and made part of the applicable plan 
for the State of California.
    (c) Regulations for visibility new source review. The provisions of 
Sec. 52.27 are hereby incorporated and made part of the applicable plan 
for the State of California only with respect to:
    (1) Mendocino County air pollution control district,
    (2) Monterey County air pollution control district,
    (3) North Coast Unified air quality management district,
    (4) Northern Sonoma County air pollution control district, and

[[Page 206]]

    (5) Sacramento County air pollution control district.
    (d) The provisions of Sec. 52.28 are hereby incorporated and made 
part of the applicable plan for the State of California, except for:
    (1) Monterey County air pollution control district, and
    (2) Sacramento County air pollution control district.
    (e) Long-term strategy. The provisions of Sec. 52.29 are hereby 
incorporated and made part of the applicable plan for the State of 
California.
[50 FR 28553, July 12, 1985, as amended at 52 FR 45138, Nov. 24, 1987]



                           Subpart G--Colorado



Sec. 52.320  Identification of plan.

    (a) Title of plan: ``Air Quality Implementation Plan for State of 
Colorado''.
    (b) The plan was officially submitted on January 26, 1972.
    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) Request for legal authority submitted February 14, 1972, by the 
Governor.
    (2) Request for 110(e) extensions submitted March 20, 1972, by the 
Governor.
    (3) Statements by State Air Pollution Control Commission (APCC) 
related to public inspection of emission data, emergency episodes, and 
transportation control submitted May 1, 1972, by the APCC. (Non-
regulatory)
    (4) List of sources under compliance schedules submitted May 1, 
1972, by the State Department of Health.
    (5) Transportation Control Plans submitted June 4, 1973, by the 
Governor.
    (6) Statements relating to transportation control plans submitted 
July 16, 1973, by the Governor. (Non-regulatory)
    (7) Plan revisions submitted November 21, 1973, by the Governor 
which delete Section III of Regulation No. 1 only as it relates to 
existing sources in Appendix P concerning SO2.
    (8) On June 7, 1974, the Governor submitted five Air Quality 
Maintenance Area designations.
    (9) Supplemental information about the Air Quality Maintenance Areas 
was submitted by the Governor on January 29, 1975.
    (10) Procedural rules for all proceedings before the Air Pollution 
Control Commission, submitted May 5, 1977, by the Governor.
    (11) On January 2, 1979, the Governor submitted the nonattainment 
area plan for all areas designated nonattainment as of March 3, 1978. 
EPA is taking no action on areas for which the Governor has requested 
redesignations (Larimer-Weld TSP and ozone; El Paso County ozone).
    (12) Extension request for attainment of CO and O3 was 
submitted by the Governor on January 5, 1979.
    (13) On July 5, 1979, the governor submitted the Air Pollution 
Control Commission's final comment on our May 11, 1979, proposal. This 
included a clarification that the ``No-Drive Day'' was not part of the 
State Implementation Plan and transportation control measures schedules 
for Larimer-Weld.
    (14) On July 18, 1979, the Commission committed to revising 
Regulation 7.
    (15) On July 23, 1979, the Governor submitted House Bill 1090 and 
Senate Bill 1 as part of the plan.
    (16) On July 27, 1979, the Governor submitted the Denver Regional 
Council of Governments schedules for implementing the transportation 
control strategies, and clarified that the Transportation Development 
Plan was part of the plan.
    (17) On March 4, 1980, the Governor submitted a plan revision to 
meet the requirements of Air Quality Monitoring 40 CFR part 58, subpart 
C, Sec. 58.20.
    (18) On May 29, 1980, the Governor submitted written evidence of the 
State's legal authority to implement and enforce an automobile emissions 
control program as well as schedules for implementing that program and a 
demonstration that it will achieve a 25% reduction in exhaust emissions 
by 1987.
    (19) On January 22 and February 6, 1980 the Governor submitted 
schedules for the implementation of transportation control measures for 
Denver and Larimer-Weld elements of the State Implementation Plan, 
respectively.
    (20) On April 21, 1980, the Governor submitted a plan revision to 
meet the data reporting requirements of section 127 of the Clean Air 
Act.
    (21) On June 22, 1980, the Governor submitted the following amended 
rules:


[[Page 207]]


    REPEAL AND REPROMULGATION OF REGULATION NO. 3 ``A Regulation 
Requiring Air Pollutant Emission Notice, Emission Permits and Fees.''
    REVISIONS TO COMMON PROVISIONS REGULATION as they relate to changes 
in Regulation No. 3.

    (22) On June 5, 1980, the Governor submitted the following rules:

    REPEAL AND REPROMULGATION OF REGULATION NO. 7 ``A Regulations to 
Control Emissions of Volatile Organic Compounds'' and revisions to the 
Common Provisions Regulations as they relate to changes in Regulation 
No. 7.

    (23) On August 25, 1980, the Governor of Colorado submitted a site 
specific revision to the State Implementation Plan for Coors Container 
Corporation, Paper Packaging Division, in regard to alternative volatile 
organic compound emissions reduction for its printing presses.
    (24) Provisions to meet the requirements of sections 110 and 172 of 
the Clean Air Act, as amended in 1977, regarding control of Group II VOC 
sources were submitted on January 6, 1981, and the supplemental 
information received on August 20, 1981.
    (25) On December 29, 1980, the Governor submitted the following 
rule: Regulation No. 11, covering procedures for garage licensing 
(including mechanic testing and licensing), equipment requirements 
(including standards and specifications for exhaust gas analyzers), 
requirements for inspections, and emission standards as part of the 
Colorado motor vehicle inspection program.
    (26) On March 23, 1981, the Governor submitted revised regulations 
limiting sulfur dioxide emissions from certain oil shale production 
facilities.
    (27) On April 12, 1982, the Governor submitted the plan revisions to 
show attainment of the lead National Ambient Air Quality Standard.
    (28) Regulation Number 7 is part of the plan.
    (29) Provisions to meet the requirements of Part D of the Clean Air 
Act for carbon monoxide in Colorado Springs, Fort Collins, and Greeley 
and ozone in Denver were submitted on June 24, 1982, and supplemented by 
information submitted on May 4, 1983,by the Colorado Air Quality Control 
Commission.
    (30) Revisions to Air Pollution Control Commission Regulation No. 1 
related to fugitive particulate emissions, were submitted by the 
Governor on June 22, 1982; on December 6, 1982; and on March 23, 1983, 
with a technical clarification dated August 5, 1982. Included is 
approval of requirements for continuous emission monitoring (CEM) of 
sulfur dioxide on fossil fuel fired steam generator with greater than 
250 million BTU per hour heat input. Also addressed is the reinstatement 
of the 40% opacity limitation for wigwam waste-wood burners into 
Regulation No. 1. With this is the addition of operation and maintenance 
(O&M) requirements to promote improved operation of the wigwam burners.
    (i) Incorporation by reference
    (A) Emission Control Regulations for Particulates, Smokes and Sulfur 
Oxides for the State of Colorado, Regulation No. 1.II (Smoke and 
Opacity); III (Particulates); IV (Continuous Emission Monitoring 
Requirements for Existing Sources; VII (Statements of Basis and 
Purpose); and Appendices A and B; which were effective on May 30, 1982.
    (B) Colorado Air Quality Control Commission Common Provisions 
Regulation which was effective on May 30, 1982.
    (C) Letter of August 5, 1982, from the State of Colorado to EPA. 
Clarification of the SIP Re: Continuous Emission Requirements for Oxides 
of Sulfur from Fossil Fueled Steam Generators.
    (31) Revisions to Air Pollution Control Commission Regulation No. 11 
related to the Colorado Inspection and Maintenance (I/M) program for 
exhaust emission inspection of motor vehicles, submitted by the Governor 
on December 10, 1984.
    (32) Revisions to Air Pollution Control Commission Regulation No. 1, 
section II.A.6 and III.C.2 (a) and (b), submitted by the Governor on 
April 9, 1985.
    (i) Incorporation by reference.
    (A) Revisions to Air Pollution Control Commission Regulation No. 1, 
``Emission Control Regulation for Particulates, Smokes, and Sulfur 
Oxides for the State of Colorado,'' sections

[[Page 208]]

II.A.6 and III.C.2 (a) and (b), effective March 2, 1985.
    (33) A revision to Regulation No. 4, ``Regulation on the Sale of New 
Woodstoves'', to control emissions from new woodstoves was submitted by 
the Governor on October 24, 1986.
    (i) Incorporation by reference
    (A) Colorado Air Quality Control Commission Regulation No. 4, 
``Regulation on the Sale of New Woodstoves'' (Section III.A., E., F., G. 
and Section VI.B. and C.) adopted June 27, 1985.
    (34) [Reserved]
    (35) Colorado Air Pollution Control Commission Regulation No. 4, 
``Regulation on the Sale of New Wood Stoves'', submitted by the Governor 
on July 18, 1985.
    (i) Incorporation by reference.
    (A) Colorado Air Quality Control Commission Regulation No. 4., 
``Regulation on the Sale of New Wood Stoves'', adopted June 27, 1985.
    (36) ``Revisions to Colorado Regulation No. 3 Requiring Air 
Contaminant Emission Notices, Emission Permits and Fees as it Relates to 
the Prevention of Significant Deterioration'' and ``Revisions to Common 
Provision Regulation as Related to Regulation 3.'' Changes submitted 
April 18, 1983, by the Governor.
    (37) Supplemental information submitted on December 16, 1985, by the 
Colorado Department of Health concerning compliance with EPA's stack 
height regulations in issuing PSD permits.
    (i) Incorporation by reference.
    (A) Revisions to Regulation 3 and Common Provisions Regulation 
adopted March 10, 1983, by the Colorado Air Quality Control Commission.
    (B) Supplemental information submitted on December 16, 1985, by the 
Colorado Department of Health concerning compliance with EPA's stack 
height regulation in issuing PSD permits.
    (38) Revisions to Regulation 1 to control emissions from alfalfa 
dehydrators were submitted by the Governor on July 29, 1987.
    (i) Incorporation by reference.
    (A) Section II.A.6 and introductory text of Section III.C.2.a of 
Regulation 1 adopted by the Colorado Air Quality Control Commission on 
January 15, 1987, effective on March 2, 1987.
    (39) Regulation 12, to control emissions from diesel fleets with 
nine or more vehicles over 7,500 pounds empty weight, registered in the 
AIR Program area (the Colorado I/M program), was submitted by the 
Governor on December 21, 1987.
    (i) Incorporation by reference
    (A) Colorado Air Quality Control Commission, Regulation No. 12, 
adopted December 18, 1986, and effective January 30, 1987.
    (40) A revision to the Colorado SIP was submitted by the Governor on 
May 8, 1986, for Visibility New Source Review.
    (i) Incorporation by Reference.
    (A) Revision to the Colorado State Implementation Plan regarding 
Revision to Regulation No. 3, Section XIV was submitted by the Governor 
on April 18, 1983, and was adopted on March 10, 1983.
    (B) Revision to the Colorado State Implementation Plan regarding 
Revision to Regulation No. 3, Section IV was submitted by the Governor 
on May 8, 1986, and was adopted on March 20, 1986.
    (41) A revision to the SIP was submitted by the Governor on December 
21, 1987, for visibility general plan requirements, monitoring, and 
long-term strategies.
    (i) Incorporation by reference:
    (A) Letter dated December 21, 1987, from Governor Roy Romer 
submitting the Colorado Visibility SIP revision.
    (B) The visibility SIP revision, Regulation No. 3, ``Regulation 
requiring an air contaminant emission notice, Emission Permit Fees'', 
section XV, adopted by the Colorado Air Quality Control Commission on 
November 19, 1987.
    (42) Revisions to Air Pollution Control Regulation No. 1, requiring 
reasonably available control technology RACT for carbon monoxide control 
on petroleum refinery catalytic cracking units were submitted by the 
Governor on May 8, 1986.
    (i) Incorporation by reference.
    (A) Revisions to Section IV., paragraphs IV.A., IV.D.2. and IV.E., 
and

[[Page 209]]

Section VII., Regulation No. 1, emission control regulations for 
particulates, smokes, carbon monoxide, and sulfur oxides for the State 
of Colorado requiring CEM and RACT on petroleum refinery catalytic 
cracking units in the metro Denver area effective on April 30, 1986.
    (43) On June 15, 1988, the Governor submitted revisions to the CO 
SIP for Colorado Springs. The revisions contain a new measure, the Clean 
Air Campaign. EPA considers all other aspects of the submittal to be 
surplus.
    (i) Incorporation by reference
    (A) Clean Air Campaign portion of the Carbon Monoxide State 
Implementation Plan for the Colorado Springs urbanized area, revised 
August 12, 1987.
    (44) A revision to Regulation No. 4 of the Colorado SIP which 
exempts certain woodburning devices from the certification requirements 
of Regulation No. 4 was submitted by the Governor of Colorado on 
September 10, 1988.
    (i) Incorporation by reference. (A) In a letter dated September 10, 
1988, Roy Romer, Governor of Colorado, submitted a revision to 
Regulation No. 4 of the Colorado SIP.
    (B) Paragraph (I)(A)(10)-(13) and (II)(C), revisions to Regulation 
No. 4, ``Regulation on the Sale of New Woodstoves,'' of the Colorado SIP 
became effective on June 30, 1988.
    (45) In a letter dated May 8, 1986, the Governor submitted revisions 
to the Colorado Regulation No. 3 (Regulation Requiring an Air 
Contaminant Emission Notice, Emission Permit Fees) of the Colorado SIP 
modifying stack evaluations. The changes consisted of (1) new 
definitions of dispersion techniques, good engineering practice, nearby, 
and excessive concentrations (Section XII.D.) and (2) rules clarifying 
technical modeling and monitoring requirements (Section XII.C.).
    (i) Incorporation by reference. (A) Revisions to the Colorado 
Regulation No. 3 (Regulation Requiring and Air Contaminant Emission 
Notice, Emission Permit Fees), Section XII, adopted March 20, 1986, by 
the Colorado Air Quality Control Commission.
    (46) On July 29, 1987, the Governor submitted:
    (1) Amendments to Colorado Regulation No. 11 (Inspection/Maintenance 
(I/M) program) and
    (2) Regulation No. 13 (oxygenated fuels program).
    (i) Incorporation by reference:
    (A) Regulation No. 11, revised January 15, 1987, effective March 2, 
1987.
    (B) Regulation No. 13, adopted June 29, 1987, effective July 30, 
1987.
    (47) In a letter dated October 23, 1985, the Director of the Air 
Pollution Control Division submitted the stack height demonstration 
analysis. Supplemental information was submitted on June 20, 1986, 
December 4, 1986, February 3, 1987, March 3, 1988, March 15, 1988, July 
6, 1988 and August 16, 1988.
    (i) Incorporation by reference. Stack height demonstration analyses 
submitted by the State on October 23, 1985, June 20, 1986, December 4, 
1986, February 3, 1987, March 3, 1988, March 15, 1988, July 6, 1988 and 
August 16, 1988.
    (48) [Reserved]
    (49) A revision to Regulation No. 4 of the Colorado SIP submitted on 
June 29, 1990, prohibits persons from operating a wood-burning stove or 
fireplace during a high pollution day in specified areas.
    (i) Incorporation by reference.
    (A) Revisions to Regulation No. 4, ``Regulation on the Sale of New 
Woodstoves,'' effective on June 30, 1990.
    (50) [Reserved]
    (51) On June 29, 1990, the Governor of Colorado submitted revisions 
to the plan. The revisions include amendments to the Common Provisions 
Regulation and Regulation No. 3 for emission permit fees and prevention 
of significant deterioration of air quality (PSD) regulations to 
incorporate the nitrogen dioxide (NO2) increments.
    (i) Incorporation by reference. (A) Revisions to the Colorado Air 
Quality Control Regulations, Common Provisions Regulation and Regulation 
No. 3, which were effective on June 30, 1990.
    (ii) Additional material. (A) October 22, 1990 letter from Douglas 
Skie, EPA, to Bradley Beckham, Director, Air Pollution Control Division.
    (B) November 5, 1990 letter from Bradley Beckham, Director, Air 
Pollution Control Division, to Douglas Skie, EPA.
    (52) [Reserved]

[[Page 210]]

    (53) Revisions to the Colorado State Implementation Plan were 
submitted by the Governor of Colorado on July 13, 1990. The revision 
adds a voluntary educational Better Air Campaign to the Ft. Collins 
Carbon Monoxide element of the Colorado SIP.
    (i) Incorporation by reference.
    (A) The Fort Collins Better Air Campaign as defined in Exhibit ``A'' 
and adopted on September 5, 1989, through Resolution 89-161.
    (54) On November 17, 1988 the Governor submitted revisions to 
Regulation No. 3 and the Common Provisions Regulation which included:
    Provisions for the review of new sources to protect the PM-10 
national ambient air quality standards (NAAQS) and for consistency with 
EPA requirements;
    Amendments to address deficiencies and previous EPA disapprovals as 
identified in the May 26, 1988 SIP Call;
    Provisions for the certification and trading of emission offset 
credits; and
    Amendments to increase permit processing and annual fees.
    (i) Incorporation by reference
    (A) Regulation No. 3: Sections I.B.2.c.(i)-(vi), I.B.3.a., II.B.1.d 
& e, II.B.3.c., II.C.1.h., II.C.3., III.A.1., IV.C.4.e., IV.C.4.f.(i) & 
(iv)-(v), IV.C.6-10, IV.D.1.e., IV.D.2.a.(iv), IV.D.2.b., IV.D.2.c.(i) & 
(ii), IV.D.3.a.(vi), IV.D.3.b.(i)(D), IV.D.3.b.(iii)(A)(3), (5), (7), & 
(11), IV.D.3.d.(ii), IV.D.3.e., IV.G.3., IV.H.7., V.C-I, VI.A.2., 
VI.C.1., VI.D., VII.A., VIII.D., IX.K., XIII.B., XIV.B.1, XIV.B.4.c.; 
and the Common Provisions Regulation: Section I.G., definitions of 
``Best Available Control Technology,'' ``Complete,'' ``Construction,'' 
``Enforceable,'' ``Fixed Capital Cost,'' ``Lowest Achievable Emission 
Rate (LAER),'' ``Modification,'' Net Emissions Increase,'' ``Particulate 
Matter,'' ``Particulate Matter Emissions,'' ``PM10,'' ``PM10 
Emissions,'' ``Reconstruction,'' ``Significant,'' ``Total Suspended 
Particulate;'' revised August 18, 1988, effective September 30, 1988.
    (ii) Additional Material
    (A) Letter dated April 29, 1991 from the Colorado Air Pollution 
Control Division to EPA.
    (55) [Reserved]
    (56) Revisions to the Colorado State Implementation Plan were 
submitted by the Governor in letters dated October 25, 1989, and October 
30, 1991. The revisions consist of amendments to Regulation No. 12, 
``Reduction of Diesel Vehicle Emissions.''
    (i) Incorporation by reference.
    (A) Regulation No. 12 revisions adopted on July 20, 1989, and 
effective on August 30, 1989, as follows: Part A (Diesel Fleet Self-
Certification Program): I.B.2.; I.C.1.; I.D.; II.A.2.b., c.; all of IV. 
except those sections noted below; and add new Parts B (Diesel Opacity 
Inspection Program) and C (Standards for Visible Pollutants from Diesel 
Engine Powered Vehicles--Operating on Roads, Streets and Highways), 
except those sections noted below. Regulation No. 12 revisions adopted 
on September 19, 1991, and effective on October 30, 1991, as follows: 
Part A: I.A.; I.B.3-18.; I.C.2.; II.A.1.; II.A.2.d., f., g., III.A.; 
IV.A.2.; IV.C.1.c., g.; IV.C.2.c., h.; IV.C.3.f., i.; IV.C.4.k.; 
IV.C.5.a.iv.; IV.C.5.b.; V.; VI.; VII.; VIII.; Part B: I.B.2., 7., 19., 
30.-37., 40., 50., 51.; I.C.2.; I.D.; I.E.3.; II.C.1.b.iv.; II.E.2.c., 
e.; II.E.8.; III.A.; III.B.4.; III.C.4.b.viii.-ix.; III.D.3.b.vi., xi.; 
III.D.3.c.viii., xiii.; V.; VI.; and Part C: A.-F.
    (57) Revision to the State Implementation Plan for Carbon Monoxide: 
Greeley Element.
    (i) Incorporation by reference.
    (A) Letter and submittal dated November 25, 1987, from the Governor 
of Colorado to the EPA Region VIII Administrator, to revise the SIP to 
include the Greeley Element. The revision was adopted by the State on 
September 17, 1987.
    (58) On November 17, 1988, the Governor submitted an amendment to 
Colorado Regulation No. 1, Section II.A.9., to exempt the destruction of 
Pershing missiles under the Intermediate-Range Nuclear Forces (INF) 
Treaty from meeting the opacity limits.
    (i) Incorporation by reference.
    (A) Regulation No. 1, Section II.A.9., adopted September 15, 1988, 
effective October 30, 1988.
    (59) Revisions to the State's new source review and prevention of 
significant deterioration permitting rules in the Common Provisions 
Regulation

[[Page 211]]

and Regulation No. 3, which were submitted by the Governor on April 9, 
1992.
    (i) Incorporation by reference.
    (A) Regulation No. 3: Sections I.A., I.B.2.c. through e., I.B.3.e. 
and f., II.B.1., II.B.2., II.C., III.A.1., III.B., III.D., IV.B.2., 
IV.C.4., IV.C.7., IV.C.9, IV.D.1., IV.D.2.a.(ii) and (iv), IV.D.2.b.(i), 
IV.D.3.a.(iii) and (vi), IV.D.3.b.(iv), IV.H., IV.I., V.A., V.C.1., 
V.C.3., V.D.1., V.D.2., V.D.4., V.D.5., V.D.11., V.E.1., V.E.5., 
V.F.10., V.F.11., V.F.13., V.G.7., V.G.8., V.H.3., V.H.7. and 8., 
V.I.3., VI.A.1., VI.C.2., IX.D., XII.D., XIII.B.4., XIII.B.6., and 
XV.D.2.; and the Common Provisions Regulation: Sections I.D.2., I.F., 
II.C.1., II.C.4., IV., and Section I.G.- definitions of ``best available 
control technology,'' ``commenced construction,'' ``complete,'' 
``federally enforceable,'' ``modification,'' ``potential to emit,'' 
``reasonable further progress,'' and ``stationary source;'' revised 
October 17, 1991, effective November 30, 1991.
    (60) Revisions to the Long-Term Strategy of the Colorado State 
Implementation Plan for Class I Visibility Protection were submitted by 
the Governor in a letter dated November 18, 1992. The submittal 
completely replaces the previous version of the Long-Term Strategy and 
includes amendments to Air Quality Control Commission Regulation No. 3, 
``Air Contaminant Emissions Notices.''
    (i) Incorporation by reference.
    (A) Revisions to the Visibility Chapter of Regulation No. 3 as 
follows: XV.F.1.c. as adopted on August 20, 1992, and effective on 
September 30, 1992.
    (61) The Governor of Colorado submitted a portion of the 
requirements for the moderate nonattainment area PM10 State 
Implementation Plan (SIP) for Denver, Colorado with a letter dated June 
7, 1993, and subsequent submittals dated September 3, 1993, and October 
20, 1993, fulfilling most of the commitments made in the June 7, 1993, 
letter. The submittals were made to satisfy those moderate 
PM10 nonattainment area SIP requirements due for the Denver 
PM10 nonattainment area on November 15, 1991. EPA is 
approving, for the limited purpose of strengthening the SIP, the control 
measures contained in the SIP revisions identified above. (EPA is not 
approving, at this time, the control measures limiting the emissions 
from Purina Mills and Electron Corporation.)
    (i) Incorporation by reference.
    (A) Revisions to Regulation No. 4, ``Regulation on the Sale of New 
Woodstoves and the Use of Certain Woodburning Appliances During High 
Pollution Days,'' as adopted by the Air Quality Control Commission on 
June 24, 1993, effective August 30, 1993, as follows: insert new Section 
VIII and recodification of References Section. This revision pertains to 
local jurisdiction implementation and enforcement of ordinances and 
resolutions restricting wood burning on high pollution days.
    (B) Regulation No. 16, ``Concerning Material Specifications for, Use 
of, and Clean-up of Street Sanding Material,'' as adopted by the Air 
Quality Control Commission on June 24, 1993, effective August 30, 1993, 
as follows: recodification of Regulation and addition of Sections II and 
III, which regulate emissions from street sanding and sweeping in the 
Denver PM10 nonattainment area.
    (C) Revisions to Regulation No. 1, ``Emission Control Regulations 
for Particulates, Smokes, Carbon Monoxide, and Sulfur Oxides for the 
State of Colorado,'' as adopted by the Air Quality Control Commission on 
August 19, 1993, effective October 30, 1993, as follows: insert new 
Sections VII and VIII and recodification of the two following Sections, 
``Emission Regulations Concerning Areas Which are Nonattainment for 
Carbon Monoxide--Refinery Fluid Bed Catalytic Cracking Units'', and 
``Statements of Basis and Purpose'' Sections. The revisions pertain to 
restrictions on the use of oil as a back-up fuel for certain sources and 
set new emission limits at the following Public Service Company Power 
Plants: Cherokee, Arapahoe, and Valmont.
    (D) Coors Glass Plant allowable emission limitations on three 
furnaces.
    1. Permit 92JE129-1, effective date January 19, 1993, regulating 
emissions at the KTG glass melting furnace #1.
    2. Permit 92JE129-2, effective date January 19, 1993, regulating 
emissions at the KTG glass melting furnace #2.

[[Page 212]]

    3. Permit 92JE129-3, effective date January 19, 1993, regulating 
emissions at the KTG glass melting furnace #3.
    (E) Conoco Refinery allowable emission limitations from the 
refinery.
    1. Permit 90AD524, effective date March 20, 1991, regulating a Tulsa 
natural gas fired 20MMbtu/hour heater equipped with low-Nox burners.
    2. Permit 90AD053, effective date March 20, 1991, regulating process 
heaters H-10, H-11 and H-27 and process boilers B4, B6, and B8 all 
burning fuel gas only.
    3. Permit 91AD180-3, effective December 28, 1992, regulating the 
three stage Claus sulfur recovery unit with tail gas recovery unit.
    (ii) Additional material.
    (A) Regional Air Quality Council, ``Guidelines for Reducing Air 
Pollution from Street Sanding'' sets voluntary guidelines for public 
works departments to follow to reduce the amount of street sand applied, 
and includes recommendations for increasing the effectiveness of street 
cleaning operations.
    (B) Adolph Coors Company Brewery permit emission limitations on five 
boilers. Permits: C-12386-1&2, C-12386-3, C-10660, C-11199, and C-11305.
    (62) On February 24, 1993, and December 9, 1993, the Governor of 
Colorado submitted revisions to the Colorado State implementation plan 
(SIP) to satisfy those moderate PM-10 nonattainment area SIP 
requirements for Pagosa Springs, Colorado due to be submitted by 
November 15, 1991. Included in the December 9, 1993 submittal were PM-10 
contingency measures for Pagosa Springs to satisfy the requirements of 
section 172(c)(9) of the Act due to be submitted by November 15, 1993.
    (i) Incorporation by reference.
    (A) Colorado Air Quality Control Commission Nonattainment Areas 
regulation, section I. ``Pagosa Springs Nonattainment Area,'' adopted on 
November 19, 1992, effective on December 30, 1992, with revisions 
adopted on November 12, 1993, effective on December 30, 1993.
    (63) On November 18, 1992, the Governor of Colorado submitted a plan 
for the establishment and implementation of a Small Business Assistance 
Program to be incorporated into the Colorado State Implementation Plan 
as required by section 507 of the Clean Air Act.
    (i) Incorporation by reference.
    (A) Colorado Revised Statutes, Sections 25-7-109.2 and 25-7-114.7, 
to establish and fund a small business stationary source technical and 
environmental compliance assistance program, effective July 1, 1992.
    (ii) Additional materials.
    (A) November 18, 1992 letter from the Governor of Colorado 
submitting a Small Business Assistance Program plan to EPA.
    (B) The State of Colorado plan for the establishment and 
implementation of a Small Business Assistance Program, adopted by the 
Colorado Air Quality Control Commission on October 15, 1992, effective 
October 15, 1992.
    (64) On December 9, 1993, the Governor of Colorado submitted 
PM10 contingency measures for the moderate nonattainment 
PM10 areas of Canon City and Lamar, Colorado. The submittal 
was made to satisfy the moderate PM10 nonattainment area 
requirements for contingency measures due for Canon City and Lamar on 
November 15, 1993.
    (i) Incorporation by reference.
    (A) Colorado Air Quality Control Commission Nonattainment Area 
Regulation, Section IV. ``Lamar Nonattainment Area,'' and Section V. 
``Canon City Nonattainment Area--PM-10,'' adopted on November 12, 1993, 
and effective December 30, 1993.
    (65) On January 15, 1992, March 17, 1993, and December 9, 1993, the 
Governor of Colorado submitted revisions to the Colorado State 
implementation plan (SIP) to satisfy those moderate PM-10 nonattainment 
area SIP requirements for Aspen, Colorado due to be submitted by 
November 15, 1991. Included in the December 9, 1993 submittal were PM-10 
contingency measures for Aspen to satisfy the requirements of section 
172(c)(9) of the Act due to be submitted by November 15, 1993.
    (i) Incorporation by reference.
    (A) Colorado Air Quality Control Commission Nonattainment Areas 
regulation, all of Section III. ``Aspen/Pitkin County PM-10 
Nonattainment Area'' except Section III.C.6., adopted on January 21, 
1993 effective on March

[[Page 213]]

2, 1993, with revisions adopted on November 12, 1993, effective on 
December 30, 1993.
    (66) On January 14, 1993, the Governor of Colorado submitted 
revisions to the new source review and prevention of significant 
deterioration requirements in the Common Provisions Regulation and 
Regulation No. 3, as well as a revision to Regulation No. 7 pertaining 
to volatile organic compounds of negligible photochemical reactivity.
    (i) Incorporation by reference.
    (A) Air Quality Control Commission Common Provisions Regulation, 
Section I.C. and Section I.G., definitions of ``adverse environmental 
effect,'' ``air pollutant,'' ``best available control technology,'' 
``federal act,'' ``federally enforceable,'' ``hazardous air pollutant,'' 
paragraph h. in ``net emissions increase,'' ``ozone depleting 
compound,'' and ``significant;'' revised 11/19/92, effective 12/30/92.
    (B) Air Quality Control Commission Regulation No. 3 Air Contaminant 
Emission Notices, Sections I.B.1., I.B.2.c-e., I.B.3.e-f., IV.B.3-5, 
IV.D.2.a.(iii), IV.D.2.c., IV.D.3., IV.D.4., IV.E., IV.F., IV.H., 
V.E.9., VI.B.1., VI.B.4., VI.B.5., VI.C., VII.C., VIII.A., VIII.C.1., 
XI.A., and XIII.A. and B.; revised 11/19/92, effective 12/30/92.
    (C) Air Quality Control Commission Regulation No. 7 Emissions of 
Volatile Organic Compounds, Section II.B.; revised 11/19/92, effective 
12/30/92.
    (67) On November 27, 1992, the Governor of Colorado, submitted a 
revision to the Colorado SIP. This revision replaces previous versions 
of Regulation No. 13 with the amended Regulation No. 13 (oxygenated 
gasoline program) adopted September 17, 1992. Regulation No. 13 requires 
the oxygenated gasoline programs to be implemented in the Fort Collins-
Loveland, Colorado Springs, and Boulder-Denver Metropolitan Statistical 
Areas (MSA) as required by Section 211(m) of the Clean Air Act 
Amendments of 1990.
    (i) Incorporation by reference.
    (A) Revision to Regulation No. 13, ``Oxygenated Gasoline Program,'' 
as adopted by the Colorado Air Quality Control Commission on September 
17, 1992, effective October 10, 1992, as follows: entire Regulation 
revision. This regulation supersedes and replaces all previous revisions 
to Regulation No. 13, (40 CFR, 52.320(46)(2)).
    (68) The Governor of Colorado submitted a portion of the 
requirements for the moderate nonattainment area PM10 State 
Implementation Plan (SIP) for Telluride, Colorado with a letter dated 
March 17, 1993. The submittal was made to satisfy those moderate 
PM10 nonattainment area SIP requirements due for Telluride on 
November 15, 1991; however, the submittal did not contain quantitative 
milestones to provide for maintenance of the PM10 National 
Ambient Air Quality Standards through December 1997. The Governor of 
Colorado submitted moderate PM10 nonattainment area 
contingency measures for Telluride with a letter dated December 9, 1993. 
This submittal was intended to satisfy the requirements of section 
172(c)(9) of the Clean Air Act due on November 15, 1993.
    (i) Incorporation by reference.
    (A) Colorado Air Quality Control Commission Nonattainment Areas 
regulation, Section II., Telluride Nonattainment Area, adopted January 
21, 1993 and effective on March 2, 1993, with revisions adopted November 
12, 1993 and effective December 30, 1993.
    (ii) Additional material.
    (A) The commitment and schedule for the adoption and implementation 
of PM10 control measures that are necessary to demonstrate 
maintenance of the 24-hour PM10 standard in Telluride, which 
were submitted in an April 21, 1994 letter from Thomas Getz, Air 
Pollution Control Division, to Douglas M. Skie, EPA.
    (69) On January 14, 1994 and on June 24, 1994, Roy Romer, the 
Governor of Colorado, submitted SIP revisions to the Implementation Plan 
for the Control of Air Pollution. This revision establishes and requires 
the implementation of an enhanced motor vehicle inspection and 
maintenance program in the Denver and Boulder urbanized areas as 
required by section 187(a)(6) of the Clean Air Act Amendments of 1990. 
This material is being incorporated by reference for the enforcement of 
Colorado's enhanced I/M program only.
    (i) Incorporation by reference.
    (A) Colo. Rev. Stat. Sections 42-4-306.5--42-4-316 adopted June 8, 
1993 as

[[Page 214]]

House Bill 93-1340, effective July 1, 1993.
    (B) Regulation No. 11 (Inspection/Maintenance Program) as adopted by 
the Colorado Air Quality Control Commission (AQCC) on March 17, 1994.
    (ii) Additional materials.
    (A) SIP narrative and technical appendices 1-20 as corrected and 
approved by the AQCC on June 21, 1994. The narrative is entitled ``State 
of Colorado Motor Vehicle Inspection and Maintenance State 
Implementation Plan'', dated December 16, 1993 with technical 
corrections.
    (70) Revisions to the Colorado State Implementation Plan were 
submitted by the Governor on September 27, 1989, and August 30, 1990. 
The revisions consist of amendments to the Ozone provisions in 
Regulation No. 7, ``Regulation To Control Emissions of Volatile Organic 
Compounds.''
    (i) Incorporation by reference.
    (A) Revisions to Regulation No. 7, Sections 7.I (Applicability), 
7.II (General Provisions), 7.III (General Requirements for Storage and 
Transfer of Volatile Organic Compounds), 7.IV (Storage of Highly 
Volatile Organic Compounds), 7.V (Disposal of Volatile Organic 
Compounds), 7.VI (Storage and Transfer of Petroleum Liquid), 7.VIII 
(Petroleum Processing and Refining), 7.IX (Surface Coating Operations), 
7.X (Use of Solvents for Degreasing and Cleaning), 7.XI (Use of Cutback 
Asphalt), 7.XII (Control of VOC Emissions from Dry Cleaning Facilities 
Using Perchloroethylene as a Solvent), 7.XIII (Graphic Arts), 7.XIV 
(Pharmaceutical Synthesis), 7.XV (Control of Volatile Organic Compound 
Leaks from Vapor Collection Systems Located at Gasoline Terminals, Bulk 
Plants, and Gasoline Dispensing Facilities), and Appendices A (Criteria 
for Control of Vapors from Gasoline Transfer to Storage Tanks), B 
(Criteria for Control of Vapors from Gasoline Transfer at Bulk Plants-
Vapor Balance System), and D (Test Procedures for Annual Pressure/Vacuum 
Testing of Gasoline Transport Trucks). The following new emission 
sources and appendices were added to Regulation No. 7: 7.IX.A.7 
(Fugitive Emission Control), 7.IX.N. (Flat Wood Paneling Coating), 
7.IX.O. (Manufacture of Pneumatic Rubber Tires), and Appendix E 
(Emission Limit Conversion Procedure). These revisions became effective 
on October 30, 1989, and August 30, 1990.
    (ii) Additional material.
    (A) February 5, 1992, letter from John Leary, Acting Director, 
Colorado Air Pollution Control Division, to Douglas Skie, EPA. This 
letter contained the State's commitment to conduct capture efficiency 
testing using the most recent EPA capture efficiency protocols, and the 
commitment to adopt federal capture efficiency test methods after they 
are officially promulgated by EPA.
    (71) The Governor of Colorado submitted carbon monoxide contingency 
measures for Colorado Springs and Fort Collins with a letter dated 
February 18, 1994. This submittal was intended to satisfy the 
requirements of section 172(c)(9) of the Clean Air Act for contingency 
measures which were due on November 15, 1993.
    (i) Incorporation by reference.
    (A) Colorado Air Quality Control Commission Nonattainment Areas 
regulation, 5 CCR 1001-20, Section VI, City of Fort Collins 
Nonattainment Area, and Section VII, Colorado Springs Nonattainment 
Area, adopted on November 12, 1993, effective on December 30, 1993.
    (72) On November 12, 1993, August 25, 1994, September 29, 1994, 
November 17, 1994, and January 29, 1996, the Governor of Colorado 
submitted revisions to the State's construction permitting requirements 
in Regulation No. 3 and the Common Provisions Regulation. These 
revisions included nonattainment new source review permitting 
requirements for new and modified major sources of PM-10 precursors 
locating in the Denver moderate PM-10 nonattainment area, changing from 
the dual source definition to the plantwide definition of source in 
nonattainment new source review permitting, other changes to Regulation 
No. 3 to make the construction permitting program more compatible with 
the State's title V operating permit program, and correction of 
deficiencies. In addition, the Governor submitted revisions to the 
Common Provisions Regulation on April 9, 1992 and January 14, 1993.
    (i) Incorporation by reference.

[[Page 215]]

    (A) Common Provisions Regulation, 5 CCR 1001-2, Section I.G., 
definitions of ``baseline area'' and ``reconstruction;'' adopted 10/17/
91, effective 11/30/91.
    (B) Common Provisions Regulation, 5 CCR 1001-2, Section I.G., 
definitions of ``net emissions increase'' and ``stationary source;'' 
adopted 8/20/92, effective 9/30/92.
    (C) Common Provisions Regulation, 5 CCR 1001-2, Section I.A. and 
Section I.G., definitions of ``emission control regulation'' and 
``volatile organic compound;'' adopted 11/19/92, effective 12/30/92.
    (D) Regulation No. 3, Air Contaminant Emissions Notices, 5 CCR 1001-
5, revisions adopted 8/18/94, effective 9/30/94, as follows: Part A 
(with the exception of the last sentence in the definition of 
``Federally enforceable'' in Section I.B.22 and with the exception of 
Section IV.C.) and Part B (with the exception of Sections V.B. and 
VII.A.5.). This version of Regulation No. 3, as incorporated by 
reference here, supersedes and replaces all versions of Regulation No. 3 
approved by EPA in previous actions.
    (E) Regulation No. 3, Air Contaminant Emissions Notices, 5 CCR 1001-
5, revisions adopted on 3/16/95, effective 5/30/95, as follows: Part A: 
Sections I.B.12., I.B.31., I.B.32., I.B.35.B., I.B.36., I.B.37., 
I.B.41., I.B.50., I.B.57., I.B.66., II.D.5.c., II.D.5.d., V.B., V.C.6., 
V.C.10., V.E.1.c., V.E.1.d., V.H.4. through V.H.8., V.I.1., VI.C.1.f., 
and VII.A.; Part B: Sections III.D.2., III.D.3., IV.B.4., IV.C.1., 
IV.D.1.a., IV.D.2.c.(i)(E), IV.D.4.a., and IV.J.
    (ii) Additional material.
    (A) July 3, 1995 letter from Martha E. Rudolph, First Assistant 
Attorney General, Colorado Office of the Attorney General, to Jonah 
Staller, EPA.
    (73) On January 14, 1994 and on June 24, 1994, Roy Romer, the 
Governor of Colorado, submitted SIP revisions to the State 
Implementation Plan for the Control of Air Pollution. This revisions 
requires the implementation of a basic motor vehicle inspection and 
maintenance program in the urbanized areas of El Paso (Colorado 
Springs), Larimer (Fort Collins), and Weld (Greeley) Counties meeting 
the requirements of the Clean Air Act Amendments of 1990. This material 
is being incorporated by reference for the enforcement of Colorado's 
basic I/M program only.
    (i) Incorporation by reference.
    (A) Colo. Rev. Stat. Secs. 42-4-306.5--42-4-316 adopted June 8, 1993 
as House Bill 93-1340, effective July 1, 1993.
    (B) Regulation No. 11 (Inspection/Maintenance Program) as adopted by 
the Colorado Air Quality Control Commission (AQCC) on March 17, 1994, 
effective April 30, 1994.
    (74) The Governor of Colorado submitted PM10 contingency 
measures for Denver, Colorado in a letter dated November 17, 1995.
    (i) Incorporation by reference.
    (A) Section IV. of Regulation No. 16, Street Sanding Emissions, 
adopted March 16, 1995, effective May 30, 1995.
    (75) The Governor of Colorado submitted revisions to the 
PM10 moderate nonattainment area State Implementation Plan 
(SIP) for Telluride, Colorado with a letter dated April 22, 1996. The 
submittal was made to satisfy the State's commitment to adopt additional 
control measures necessary to demonstrate continued maintenance of the 
PM10 National Ambient Air Quality Standards through 1997. Due 
to the satisfaction of this commitment, the SIP now adequately meets the 
quantitative milestone requirement.
    (i) Incorporation by reference.
    (A) Colorado Air Quality Control Commission State Implementation 
Plan-Specific Regulation for Nonattainment Areas, 5 CCR 1001-20, Section 
II.C., Telluride Nonattainment Area Street Sanding Requirements, adopted 
August 17, 1995 and effective October 30, 1995.
    (76) The Governor of Colorado submitted the moderate nonattainment 
area PM10 State Implementation Plan (SIP) for Steamboat 
Springs, Colorado with a letter dated September 16, 1997. The submittal 
was made to satisfy those moderate PM10 nonattainment area 
SIP requirements due for Steamboat Springs on July 20, 1995, including 
among other things, control measures, technical analyses, quantitative 
milestones, and contingency measures. The September 16, 1997 submittal 
also included the Steamboat Springs emergency episode plan.
    (i) Incorporation by reference.

[[Page 216]]

    (A) Colorado Air Quality Control Commission Nonattainment Areas, 5 
CCR 1001-20, Section VIII., Steamboat Springs PM10 
Nonattainment Area, adopted October 17, 1996 and effective on December 
30, 1996.
    (ii) Additional material.
    (A) An October 29, 1997 letter from Margie M. Perkins, APCD, to 
Richard R. Long, EPA, clarifying that the regulation entitled ``Ambient 
Air Quality Standards for the State of Colorado'' was included in the 
September 16, 1997 Steamboat Springs SIP submittal for informational 
purposes only.
    (77) On September 29, 1995, Roy Romer, the Governor of Colorado, 
submitted a SIP revision to the State Implementation Plan for the 
Control of Air Pollution. This revision provides a replacement 
Regulation No. 11, Inspection/Maintenance Program which limits dealer 
self-testing. This material is being incorporated by reference for the 
enforcement of Colorado's I/M program.
    (i) Incorporation by reference.
    (A) Department of Health, Air Quality Control Commission, Regulation 
No. 11 (Motor Vehicle Emissions Inspection Program) as adopted by the 
Colorado Air Quality Control Commission (AQCC) on September 22, 1994, 
effective November 30, 1994.
    (78) Revisions to the Colorado State Implementation Plan were 
submitted by the Governor of the State of Colorado on August 25, 1995, 
and October 16, 1995. The revisions consist or amendments to Regulation 
No. 3, ``Air Contaminant Emissions Notices'' and to Regulation No. 7, 
``Regulation To Control Emissions of Volatile Organic Compounds.'' These 
revisions involve source-specific State Implementation Plan requirements 
for emission trading for Pioneer Metal Finishing Inc. and crossline 
averaging for Lexmark International Inc.
    (i) Incorporation by reference.
    (A) Revisions to Regulation No. 3, 5 CCR 1001-5, sections V.A. 
(Purpose), V.C.1 , V.C.3, V.C.5 (Definitions), V.D.6, V.D.7, V.D.9 
(Procedure for Certification of Emissions Reductions and Approval of 
Transactions), V.E. (Criteria for Certification of Emissions 
Reductions), V.F., V.F.5, V.F.7, V.F.8.l, V.F.14, and V.F.15 (Criteria 
for Approval of all Transactions) and Revisions to Regulation No. 7, 5 
CCR 1001-9, section II.D.1.a (Alternative Control Plans and Test 
Methods) became effective on December 30, 1994. The new section IX.L.2.c 
through IX.L.2.c.xv (Manufactured Metal Parts and Metal Products) to 
Regulation No. 7, 5 CCR 1001-9, applicable to Pioneer Metal Finishing 
Inc., became effective on April 30, 1995. The new section IX.A.12 
through IX.A.12.a.(xi) (General Provisions) to Regulation No. 7, 5 CCR 
1001-9, applicable to Lexmark International Inc., became effective July 
30, 1995.
    (79) On August 23, 1996, the Governor of Colorado submitted a 
revision to the long-term strategy portion of Colorado's State 
Implementation Plan (SIP) for Class I Visibility Protection. The 
revision was made to incorporate into the SIP, among other things, 
emissions reduction requirements for the Hayden Station (a coal-fired 
steam generating plant located near the town of Hayden, Colorado) that 
are based on a consent decree addressing numerous air pollution 
violations at the plant. This SIP revision replaces the previous 
existing impairment portion of the long-term strategy as it relates to 
the Mt. Zirkel Wilderness Area.
    (i) Incorporation by reference.
    (A) Long-Term Strategy Review and Revision of Colorado's State 
Implementation Plan for Class I Visibility Protection Part I: Hayden 
Station Requirements, as follows: Section VI., effective on August 15, 
1996.
    (80) On July 11, 1994, July 13, 1994, September 29, 1995, and 
December 22, 1995, the Governor of Colorado submitted revisions to the 
Colorado State Implementation Plan (SIP) to satisfy those CO 
nonattainment area SIP requirements for Denver and Longmont, Colorado 
due to be submitted by November 15, 1992, and further revisions to the 
SIP to shorten the effective period of the oxygenated fuels program. EPA 
is not taking action on the SIP provision submitted on July 11, 1994 
that calls for a prohibition of the re-registration of abandoned and 
impounded vehicles.
    (i) Incorporation by reference.
    (A) Regulation No. 11, Motor Vehicle Emissions Inspection Program, 5 
CCR 1001-13, as adopted on September 22,

[[Page 217]]

1994, effective November 30, 1994. Regulation No. 13, Oxygenated Fuels 
Program, 5 CCR 1001-16, as adopted on October 19, 1995, effective 
December 20, 1995.
    (81) On August 1, 1996, the Governor of Colorado submitted revisions 
to the prevention of significant deterioration regulations in Regulation 
No. 3 to incorporate changes in the Federal PSD permitting regulations 
for PM-10 increments and to make other minor administrative revisions.
    (i) Incorporation by reference.
    (A) Regulation No. 3, Air Contaminant Emissions Notices, 5 CCR 1001-
5, revisions adopted 8/17/95, effective 10/30/95, as follows: Part A, 
Section I.B., as follows: the definition of ``baseline area'' in 
subsection 10, the definition of ``minor source baseline date'' in 
subsection 35, and the definition of ``net emissions increase'' in 
subsection 37; Part A: Sections IV.B., V.C.1., and V.D.11.c.; Part B: 
Sections IV.D.3.b.(v), VII.A.1., and X.D.
    (82) The Governor of Colorado submitted the Denver moderate 
nonattainment area PM10 State Implementation Plan (SIP) with 
a letter dated March 30, 1995. The Governor submitted revisions to 
Regulation No. 13, one of the control measures relied on in the 
PM10 SIP, on December 22, 1995. These submittals as well as 
support documentation submittals made on June 8, 1993, June 10, 1993, 
June 25, 1993, July 19, 1993, August 5, 1993, September 3, 1993, 
September 21, 1993, October 20, 1993, December 12, 1993, January 19, 
1994, December 23, 1994, March 3, 1995, and November 8, 1995 satisfy 
those moderate PM10 nonattainment area SIP requirements due 
for the Denver PM10 nonattainment area on November 15, 1991. 
EPA is approving the SIP. This approval replaces the previous limited 
approval at 40 CFR 52.320(c)(61).
    (i) Incorporation by reference.
    (A) Regulation No. 4, ``Regulation on the Sale of New Woodstoves and 
the Use of Certain Woodburning Appliances During High Pollution Days,'' 
5 CCR 1001-6, as adopted by the Air Quality Control Commission on June 
24, 1993, effective August 30, 1993.
    (B) Local woodburning ordinances and resolutions.
    (1) Arvada, Colorado. Ordinance number 2451, effective November 2, 
1987, regarding woodburning restrictions.
    (2) Aurora, Colorado. Ordinance numbers 87-118 and 92-14, effective 
May 22, 1987 and May 22, 1992, respectively, regarding woodburning 
restrictions.
    (3) Boulder, Colorado. Ordinance numbers 5007 and 5445, adopted 
November 25, 1986 and April 21, 1992, respectively, regarding 
woodburning restrictions.
    (4) Broomfield, Colorado. Ordinance number 794, effective November 
24, 1988, regarding woodburning restrictions.
    (5) Denver, Colorado. Ordinance numbers 293 and 1018, approved May 
30, 1990 and December 16, 1993, respectively, regarding woodburning 
restrictions.
    (6) Douglas County, Colorado. Resolution number 991-128, adopted 
November 14, 1991, regarding woodburning restrictions.
    (7) Englewood, Colorado. Ordinance numbers 31 and 39, passed on July 
20, 1992, regarding woodburning restrictions.
    (8) Federal Heights, Colorado. Ordinance number 565, adopted January 
5, 1988, regarding woodburning restrictions.
    (9) Glendale, Colorado. Ordinance numbers 2 and 14, adopted January 
5, 1988 and effective on October 20, 1992, respectively, regarding 
woodburning restrictions.
    (10) Greenwood Village, Colorado. Ordinance numbers 17 and 9, 
effective July 9, 1988 and March 25, 1992, respectively, regarding 
woodburning restrictions.
    (11) Jefferson County, Colorado. Resolution numbers CC89-873 and 
CC90-617, dated December 29, 1989 and August 7, 1990, respectively, 
regarding woodburning restrictions.
    (12) Lafayette, Colorado. Ordinance number 24; series 1988, 
effective November 15, 1988, regarding woodburning prohibitions.
    (13) Lakewood, Colorado. Ordinance numbers 0-86-113 and 0-92-61, 
effective December 1, 1986 and November 28, 1992, respectively, 
regarding woodburning restrictions.
    (14) Littleton, Colorado. Ordinance numbers 51 and 26, passed on 
December

[[Page 218]]

6, 1988 and August 18, 1992, respectively, regarding woodburning 
restrictions.
    (15) Longmont, Colorado. Ordinance number 0-89-1, adopted December 
27, 1988, regarding woodburning restrictions.
    (16) Mountain View, Colorado. Ordinance number 90-5, approved on 
January 7, 1991, regarding woodburning restrictions.
    (17) Sheridan, Colorado. Ordinance numbers 22 and 1, approved 
October 25, 1988 and February 9, 1993, respectively, regarding 
woodburning restrictions.
    (18) Thornton, Colorado. Ordinance numbers 2120 and 2194, adopted 
October 28, 1991 and September 28, 1992, respectively, regarding 
woodburning restrictions.
    (19) Westminster, Colorado. Ordinance numbers 1742 and 2092, enacted 
on November 9, 1987 and December 28, 1992, respectively, regarding 
woodburning restrictions.
    (C) Regulation No. 16, ``Concerning Material Specifications for, Use 
of, and Clean-up of Street Sanding Material,'' 5 CCR 1001-18, as adopted 
by the Air Quality Control Commission on September 22, 1994, effective 
November 30, 1994.
    (D) Regulation No. 1, ``Emission Control Regulations for 
Particulates, Smokes, Carbon Monoxide, and Sulfur Oxides for the State 
of Colorado,'' 5 CCR 1001-3, Sections I-IV and VI-IX, and Appendices A 
and B, as adopted by the Air Quality Control Commission on August 19, 
1993, effective October 20, 1993; with revisions to Sections VII and 
VIII, adopted by the Air Quality Control Commission on September 22, 
1994, effective November 30, 1994.
    (E) Public Service Company Cherokee facility SO2 emission 
limitations for the power facility.
    (1) Permit 86AD352(1), effective date November 13, 1986, regulates 
SO2 emissions at Unit #1.
    (2) Permit 86AD352-2, effective date April 30, 1992, regulates 
SO2 emissions at Unit #4.
    (F) Purina Mills Inc. total PM10 emissions limitations at 
the animal feed manufacturing facility.
    (1) Permit 93AD1008-1, effective date October 19, 1993, regulating 
emissions at the finished product loadout facility.
    (2) Permit 93AD1008-2, effective date October 19, 1993, regulating 
emissions at the grain receiving facility.
    (G) Electron Corporation total PM10 emission limitations 
at the gray iron foundry.
    (1) Permit 93AR1363-1, effective date January 12, 1994, regulating 
emissions at the Table shot blaster and associated baghouse.
    (2) Permit 93AR1363-2, effective date January 12, 1994, regulating 
emissions at the five grinding booths-stand and associated baghouse.
    (3) Permit 93AR1363-3, effective date January 12, 1994, regulating 
emissions at the five grinding booths-hand and associated baghouse.
    (4) Permit 93AR1363-4, effective date January 12, 1994, regulating 
emissions at the Muller-25 sand system and associated baghouse.
    (5) Permit 93AR1363-5, effective date January 12, 1994, regulating 
emissions at the Coleman core oven-sand.
    (6) Permit 93AR1363-6, effective date January 12, 1994, regulating 
emissions at the Spinner wheelabrator and associated baghouse.
    (7) Permit 93AR1363-7, effective date January 12, 1994, regulating 
emissions at the Sand sile-core room and associated baghouse.
    (8) Permit 93AR1363-8, effective date January 12, 1994, regulating 
emissions from pouring of molten iron (casting) and castings cooling.
    (9) Permit 93AR1363-9 effective date January 12, 1994, regulating 
emissions at three tumble blast machines and associated baghouse.
    (10) Permit 93AR1363-10, effective date January 12, 1994, regulating 
emissions at two mullers-80A and associated baghouse.
    (11) Permit 93AR1363-11, effective date January 12, 1994, regulating 
emissions at the Casting shakeout hood and associated baghouse.
    (12) Permit 93AR1363-12, effective date January 12, 1994, regulating 
emissions at the Casting-disamatic mold and associated baghouse.
    (13) Permit 93AR1363-13, effective date January 12, 1994, regulating 
emissions at the Sand silo-disamatic and associated baghouse.

[[Page 219]]

    (14) Permit 93AR1363-14, effective date January 12, 1994, regulating 
emissions at the Sand silo-air set room and associated baghouse.
    (15) Permit 93AR1363-15, effective date January 12, 1994, regulating 
emissions at two electric induction furnaces and associated baghouse.
    (16) Permit 93AR1363-16, effective date January 12, 1994, regulating 
emissions at two Inducto-Therm electric induction furnaces model #2000/
4, serial nos. 40102 and 40103, and associated baghouse.
    (17) Permit 93AR1363-17, effective date January 12, 1994, regulating 
emissions from chemicals used in core making process.
    (18) Permit 93AR1363-18, effective date January 12, 1994, regulating 
emissions at the Loop shakeout and associated baghouse.
    (19) Permit 93AR1363-19, effective date January 12, 1994, regulating 
emissions at the Floor shakeout and associated baghouse.
    (20) Permit 93AR1363-20, effective date January 12, 1994, regulating 
emissions at the Reclaim sand and associated baghouse.
    (21) Permit 93AR1363-21 effective date January 12, 1994, regulating 
emissions at the Sand heater/cooler and associated baghouse.
    (22) Permit 93AR1363-22, effective date January 12, 1994, regulating 
emissions at the Paint spray booth.
    (H) TRIGEN-Colorado Energy Corporation permit emissions limitations 
at two boilers.
    (1) Permit 10JE660, effective date February 25, 1997, regulating 
emissions at the #4 boiler: tangential fired cogeneration steam boiler.
    (2) Permit 11JE305-1, effective date February 19, 1997, regulating 
emissions at the #5 boiler: tangential fired cogeneration steam boiler.
    (I) Rocky Mountain Bottle Company emission limitations on three 
furnaces.
    (1) Permit 92JE129-1, effective date June 29, 1995, regulating 
emissions at the KTG glass melting furnaces #1, #2 and #3.
    (J) Conoco Refinery allowable emission limitations from the 
refinery.
    (1) Permit 90AD524, effective date March 20, 1991, regulating a 
Tulsa natural gas fired 20MMbtu/hour heater equipped with low-
NOX burners.
    (2) Permit 90AD053, effective date March 20, 1991, regulating 
process heaters H-10, H-11 and H-27 and process boilers B4, B6, and B8 
all burning fuel gas only.
    (3) Permit 91AD180-3, effective December 28, 1992, regulating the 
three stage Claus sulfur recovery unit with tail gas recovery unit.
    (ii) Additional material.
    (A) Regional Air Quality Council, ``Guidelines for Reducing Air 
Pollution from Street Sanding'' sets voluntary guidelines for public 
works departments to follow to reduce the amount of street sand applied, 
and includes recommendations for increasing the effectiveness of street 
cleaning operations.
    (84) The Governor of Colorado submitted the Denver PM10 mobile 
source emissions budget State Implementation Plan (SIP) with a letter 
dated July 18, 1995. The Governor submitted the Denver NOX 
mobile source emissions budget State Implementation Plan (SIP) with a 
letter dated April 22, 1996. The PM10 and NOX mobile source 
emissions budgets and other provisions in these SIP submittals are used 
to assess conformity of transportation plans, transportation improvement 
programs, and transportation projects.
    (i) Incorporation by reference.
    (A) Colorado Air Quality Control Commission, ``Ambient Air Quality 
Standards'' regulation 5CCR 1001-14, Section A.1. Budgets for the Denver 
Nonattainment Area (Modeling Domain) PM10, Sections A.2. and A.3., and 
Sections B and C, adopted on February 16, 1995, effective April 30, 
1995, as amended by the Colorado General Assembly through enactment of 
Colorado Senate Bill 95-110, which Bill was enacted on May 5, 1995 and 
signed by the Governor of Colorado on May 31, 1995. (See paragraph 
(c)(84)(i)(B) of this section).
    (B) Colo. Rev. Stat. section 25-7-105(1)(a)(III), enacted by the 
Colorado General Assembly on May 5, 1995 as part of Colorado Senate Bill 
95-110 and signed by the Governor of Colorado on May 31, 1995.
    (C) Colorado Air Quality Control Commission ``Ambient Air Quality 
Standards'' regulation 5CCR 1001-14,

[[Page 220]]

Section A.1. Budgets for the Denver Nonattainment Area (Modeling Domain) 
Nitrogen Oxides, as adopted June 15, 1995, effective August 30, 1995.
[37 FR 10855, May 31, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.320, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.321  Classification of regions.

    The Colorado plan was evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                                  Pollutant
                                                           -----------------------------------------------------
                Air quality control region                  Particulate   Sulfur   Nitrogen   Carbon
                                                               matter     oxides    dioxide  monoxide    Ozone
----------------------------------------------------------------------------------------------------------------
Pawnee Intrastate.........................................           I        III       III       III        III
Metropolitan Denver Intrastate............................           I        III       III         I          I
Comanche Intrastate.......................................         III        III       III       III        III
San Isabel Intrastate.....................................           I        III       III       III        III
San Luis Intrastate.......................................         III        III       III       III        III
Four Corners Interstate...................................          IA         IA       III       III        III
Grand Mesa Intrastate.....................................         III        III       III       III        III
Yampa Intrastate..........................................         III        III       III       III        III
----------------------------------------------------------------------------------------------------------------

[37 FR 10855, May 31, 1972, as amended at 39 FR 16346, May 8, 1974; 44 
FR 57409, Oct. 5, 1979]



Sec. 52.322  Extensions.

    The Administrator, by authority delegated under section 188(d) of 
the Clean Air Act, as amended in 1990, extends for one year (until 
December 31, 1995) the attainment date for the Denver, Colorado, PM-10 
nonattainment area.
[60 FR 52315, Oct. 6, 1995]



Sec. 52.323  Approval status.

    With the exceptions set forth in this subpart, the Administrator 
approves Colorado's plan for the attainment and maintenance of the 
national standards under section 110 of the Clean Air Act. Furthermore, 
the Administrator finds that the plan satisifies all requirements of 
Part D, Title 1, of the Clean Air Act as amended in 1977, except as 
noted below.
[44 FR 57410, Oct. 5, 1979]



Sec. 52.324  Legal authority.

    (a) The requirements of Sec. 51.230(f) of this chapter are not met 
since the State lacks the authority to require owners or operators of 
stationary sources to install, maintain, and use emission monitoring 
devices and to make periodic reports to the State on the nature and 
amounts of emissions from such stationary sources.
    (b) Delegation of authority: Pursuant to section 114 of the Act, 
Colorado requested a delegation of authority to enable it to require 
sources to install and maintain monitoring equipment and to report 
periodically on the nature and amount of their emissions. The 
Administrator has determined that Colorado is qualified to receive a 
delegation of the authority it requested. Accordingly, the Administrator 
delegates to Colorado his authority under section 114(a)(1)(B) and (C) 
of the Act, i.e., authorityto require sources within the State of 
Colorado to install and maintain monitoring equipment and to report 
periodically on the nature and amount of their emissions.
[37 FR 10855, May 31, 1972, as amended at 46 FR 24182, Apr. 30, 1981; 51 
FR 40676, Nov. 7, 1986; 62 FR 2914, Jan. 21, 1997]



Sec. 52.325  [Reserved]



Sec. 52.326  Area-wide nitrogen oxides (NOX) exemptions.

    The Denver Regional Council of Governments (DRCOG) submitted a 
NOX exemption petition to the EPA on May 25, 1994 and 
submitted supporting documentation via a letter dated August 1, 1994. 
This petition requested that the Denver metropolitan area, a 
transitional ozone nonattainment area, be exempted from the requirement 
to meet the NOX provisions of the Federal transportation and 
general conformity rule with respect to ozone. The exemption request was 
based on monitoring

[[Page 221]]

data which demonstrated that the National Ambient Air Quality Standard 
for ozone had been attained in this area for the 3 years prior to the 
petition. The EPA approved this exemption request on July 28, 1995.
[60 FR 40291, Aug. 8, 1995]



Secs. 52.327--52.328  [Reserved]



Sec. 52.329  Rules and regulations.

    (a) On January 14, 1993, the Governor of Colorado submitted 
revisions to the State's nonattainment new source review permitting 
regulations to bring the State's regulations up to date with the 1990 
Amendments to the Clean Air Act. With these revisions, the State's 
regulations satisfy the part D new source review permitting requirements 
for the following nonattainment areas: the Canon City, Lamar, Pagosa 
Springs, Aspen, Telluride, and Steamboat Springs moderate 
PM10 nonattainment areas, the Denver/Metro Boulder, Longmont, 
Colorado Springs, and Fort Collins moderate carbon monoxide 
nonattainment areas, the Greeley not classified carbon monoxide 
nonattainment area, and the Denver transitional ozone nonattainment 
area.
    (b) On January 14, 1993 and on August 25, 1994, the Governor of 
Colorado submitted revisions to the State's nonattainment new source 
review permitting regulations to bring the State's regulations up to 
date with the 1990 Amendments to the Clean Air Act. With these 
revisions, the State's regulations satisfy the part D new source review 
permitting requirements for the Denver metropolitan moderate PM-10 
nonattainment area.
[59 FR 64336, Dec. 14, 1994, as amended at 62 FR 2914, Jan. 21, 1997; 62 
FR 68195, Dec. 31, 1997]



Sec. 52.330  Control strategy: Total suspended particulates.

    (a) Part D--Conditional Approval: The Pueblo plan is approved 
assuming the State demonstrates by December 31, 1981, through air 
quality modeling, attainment of the 24-hour and annual standards, while 
considering emissions from all sources in the nonattainment area. In 
addition, the State must repromulgate Regulation No. 1 to satisfy 
reasonably available control technology requirements in accordance with 
the following schedule:
    (1) The Commission will consider and adopt for public hearing any 
changes or additions to Regulation No. 1 by February 15, 1981.
    (2) The proposed regulations will be published in the Colorado 
Register by March 10, 1981.
    (3) Public hearing will be held by May 14, 1981.
    (4) Regulations will be approved with an effective date no later 
than July 1, 1981, and submitted to EPA by the same date.
[46 FR 26302, May 12, 1981]



Sec. 52.331  Committal SIP for the Colorado Group II PM10 areas.

    On April 14, 1989, the Governor submitted a Committal SIP for the 
Colorado Group II PM10 areas. The SIP commits the State to 
continue to monitor for PM10, report data and to submit a 
full SIP if a violation of the PM10 National Ambient Air 
Quality Standards is detected.
[54 FR 43178, Oct. 23, 1989]



Sec. 52.332  Moderate PM-10 nonattainment area plans.

    (a) On April 9, 1992, the Governor of Colorado submitted the 
moderate PM-10 nonattainment area plan for the Canon City area. The 
submittal was made to satisfy those moderate PM-10 nonattainment area 
SIP requirements which were due for Canon City on November 15, 1991.
    (b)(1) On February 24, 1992, and December 9, 1993, the Governor of 
Colorado submitted the moderate PM-10 nonattainment area plan for the 
Pagosa Springs area. The submittal was made to satisfy those moderate 
PM-10 nonattainment area SIP requirements which were due for Pagosa 
Springs on November 15, 1991.
    (2) On August 2, 1996, the Governor of Colorado submitted minor 
revisions to the Pagosa Springs Element of the Colorado PM-10 SIP.
    (c) On May 27, 1993, the Governor of Colorado submitted the moderate 
PM-10 nonattainment area plan for the Lamar area. The submittal was made 
to satisfy those moderate PM-10 nonattainment area SIP requirements

[[Page 222]]

which were due for Lamar on November 15, 1991.
    (d) On December 9, 1993, the Governor of Colorado submitted 
PM10 contingency measures for the moderate PM10 
nonattainment areas of Canon City, Lamar, and Pagosa Springs. The 
submittal was made to satisfy the moderate PM10 nonattainment 
area requirements for contingency measures due for Canon City, Lamar, 
and Pagosa Springs on November 15, 1993.
    (e)(1) On January 15, 1992, March 17, 1993, and December 9, 1993, 
the Governor of Colorado submitted the moderate PM-10 nonattainment area 
plan for the Aspen area. The submittals were made to satisfy those 
moderate PM-10 nonattainment area SIP requirements which were due for 
Aspen on November 15, 1991. The December 9, 1993 submittal was also made 
to satisfy the PM-10 contingency measure requirements which were due for 
Aspen on November 15, 1993.
    (2) On March 13, 1995, the Governor of Colorado submitted minor 
revisions to the Aspen Element of the Colorado PM-10 SIP.
    (f) On March 30, 1995, and November 17, 1995, the Governor of 
Colorado submitted the moderate PM10 nonattainment area plan 
for the Denver area. The March 30, 1995 submittal was made to satisfy 
those moderate PM10 nonattainment area SIP requirements due 
for the Denver PM10 nonattainment area on November 15, 1991. 
The November 17, 1995 submittal was also made to satisfy the 
PM10 contingency measure requirements which were due for 
Denver on November 15, 1993.
    (g) On March 17, 1993, December 9, 1993, and April 22, 1996, the 
Governor of Colorado submitted the moderate PM10 
nonattainment area plan for Telluride. The submittals were made to 
satisfy those moderate PM10 nonattainment area SIP 
requirements which were due for Telluride on November 15, 1991. The 
December 9, 1993 submittal was also made to satisfy the PM10 
contingency measure requirements which were due for Telluride on 
November 15, 1993.
    (h) On September 16, 1997 the Governor of Colorado submitted the 
moderate PM10 nonattainment area plan for Steamboat Springs. 
The submittal was made to satisfy those moderate PM10 
nonattainment area SIP requirements which were due for Steamboat Springs 
on July 20, 1995.
[58 FR 68038, Dec. 23, 1993, as amended at 59 FR 26128, May 19, 1994; 59 
FR 29734, June 9, 1994; 59 FR 47095, Sept. 14, 1994; 59 FR 64336, Dec. 
14, 1994; 62 FR 18723, Apr. 17, 1997; 62 FR 66008, Dec. 17, 1997; 62 FR 
68195, Dec. 31, 1997]



Secs. 52.333--52.342  [Reserved]



Sec. 52.343  Significant deterioration of air quality.

    (a) The requirements of sections 160 through 165 of the Clean Air 
Act are not met for the following categories of sources for preventing 
the significant deterioration of air quality:
    (1) Sources locating on Indian lands.
    (2) Sources locating on Indian Reservations.
    (3) Sources which constructed prior to September 2, 1986 and which 
have not otherwise subjected themselves to Colorado's PSD permitting 
regulations after September 2, 1986, either through application to 
Colorado for a PSD permit (in the case of those sources which improperly 
constructed without obtaining a PSD permit) or through application to 
Colorado for a major modification to the source.
    (b) Regulations for preventing significant deterioration of air 
quality. The provisions of Sec. 52.21 (b) through (w) are hereby 
incorporated and made a part of the applicable state plan for the State 
of Colorado for the sources identified in paragraph (a) as not meeting 
the requirements of sections 160-165 of the Clean Air Act.
    (c) The State of Colorado has clarified the generalized language 
contained in the Colorado Air Quality Control Regulations on the use of 
``applicable air quality models.'' In a letter to Douglas M. Skie, EPA, 
dated May 19, 1989, Bradley J. Beckham, Director of the Air Pollution 
Control Division stated:

    * * * All PSD permits reviewed by the Division will use the revised 
modeling guideline mentioned above [Guideline on Air Quality Models 
(Revised), EPA 450/2-78-027R including Supplement A (July 1987)] for 
determining if the air quality models, data bases,

[[Page 223]]

and other requirements are generally approved by EPA. Any future 
revisions (including appendices or supplement) will be incorporated into 
the Division's protocol for reviewing modeling for PSD permits.
[51 FR 31126, Sept. 2, 1986, and 52 FR 4622, Feb. 13, 1987, as amended 
at 52 FR 22638, June 15, 1987; 54 FR 27881, July 3, 1989; 57 FR 27000, 
June 17, 1992; 59 FR 42506, Aug. 18, 1994; 62 FR 2914, Jan. 21, 1997; 62 
FR 13336, Mar. 20, 1997]



Sec. 52.344  Visibility protection.

    (a) A revision to the SIP was submitted by the Governor on December 
21, 1987, for visibility general plan requirements, monitoring, and 
long-term strategies.
    (b) The Visibility NSR regulations are approved for industrial 
source categories regulated by the NSR and PSD regulations which have 
previously been approved by EPA. However, Colorado's NSR and PSD 
regulations have been disapproved for certain sources as listed in 40 
CFR 52.343(a)(1). The provisions of 40 CFR 52.26 and 52.28 are hereby 
incorporated and made a part of the applicable plan for the State of 
Colorado for these sources.
[50 FR 28553, July 12, 1985, as amended at 52 FR 45137, Nov. 24, 1987; 
53 FR 30431, Aug. 12, 1988; 53 FR 48539, Dec. 1, 1988; 59 FR 51379, Oct. 
11, 1994]



Sec. 52.345  Stack height regulations.

    The State of Colorado has committed to revise its stack height 
regulations should EPA complete rulemaking to respond to the decision in 
NRDC v. Thomas, 838 F. 2d 1224 (DC Cir. 1988). In a letter to Mr. 
Douglas M. Skie, EPA, dated May 9, 1988, Bradley J. Beckham, Director of 
the Colorado Air Pollution Control Division stated:

    * * * We are submitting this letter to allow EPA to continue to 
process our current SIP submittal with the understanding that if EPA's 
response to the NRDC remand modified the July 8, 1985, regulations, EPA 
will notify the state of the rules that must be changed to comply with 
the EPA's modified requirements. The State of Colorado agrees to make 
appropriate changes.
[54 FR 24340, June 7, 1989]



Sec. 52.346  Air quality monitoring requirements.

    In a letter and submittal dated July 7, 1993, from the Governor of 
Colorado to the EPA Region VIII Administrator, the State submitted a 
revised Air Quality Monitoring State Implementation Plan. The plan was 
adopted by the State on March 18, 1993, and completely replaces the 
previous version of the Air Quality Monitoring plan as identified at 40 
CFR 52.320 (c)(17). The revisions updated the plan to bring it into 
conformance with the Federal requirements for air quality monitoring as 
found in 40 CFR part 58. The State commits to meet these Federal 
requirements.
[58 FR 49435, Sept. 23, 1993]



Sec. 52.347  [Reserved]



Sec. 52.348  Emission inventories.

    The Governor of the State of Colorado submitted the 1990 carbon 
monoxide base year emission inventories for the Colorado Springs, 
Denver/Longmont, and Fort Collins nonattainment areas on December 31, 
1992, as a revision to the State Implementation Plan (SIP). The Governor 
submitted revisions to the Colorado Springs and Fort Collins inventories 
by a letter dated March 23, 1995. The Governor submitted revisions to 
the Denver/Longmont inventory by letters dated July 11, 1994, and 
October 21, 1994. The inventories address emissions from point, area, 
on-road mobile, and non-road sources. These 1990 base year carbon 
monoxide inventories satisfy the requirements of section 187(a)(1) of 
the Clean Air Act for each of these nonattainment areas.
[61 FR 67469, Dec. 23, 1996]



                         Subpart H--Connecticut



Sec. 52.370  Identification of plan.

    (a) Title of plan: ``State of Connecticut Air Implementation Plan.''
    (b) The plan was officially submitted on March 3, 1972.
    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) Miscellaneous non-regulatory addition to the plan and addition 
of amendment to Chapter 360 of General Statutes which provides authority 
for delegation of enforcement authority submitted on March 21, 1972, by 
the Connecticut Department of Environmental Protection.

[[Page 224]]

    (2) Miscellaneous non-regulatory additions to the plan submitted on 
April 6, 1972, by the Connecticut Department of Environmental 
Protection.
    (3) Attainment dates submitted on August 10, 1972, by the 
Connecticut Department of Environmental Protection.
    (4) Regulation 19-508-100 requiring a review of indirect sources 
submitted on January 9, 1974, by the Connecticut Department of 
Environmental Protection.
    (5) AQMA identification material submitted on April 15, 1974, by the 
Connecticut Department of Environmental Protection.
    (6) Indirect Source Review Regulation 19-508-100 resubmitted on 
August 26, 1974, by the Connecticut Department of Environmental 
Protection.
    (7) [Reserved]
    (8) Revision to Chapter 8, Air Quality Surveillance, submitted on 
June 30, 1977, by the Governor.
    (9) Revision to Indirect Source Review Regulation 19-508-100 
submitted on June 13, 1977, by the Connecticut Department of 
Environmental Protection.
    (10) A revision to Regulation 19-508-19(a)(2)(i) submitted by the 
Commissioner of the Connecticut Department of Environmental Protection 
on April 16, 1979, granting a variance until April 1, 1981, to Northeast 
Utilities.
    (11) State Implementation Plan revisions to meet the requirements of 
part D of the Clean Air Act, as amended in 1977, were submitted on June 
22, 1979, and received on June 27, 1979; submitted on December 18, 1979 
and received on December 28, 1979; submitted on January 28, 1980, and 
received on February 1, 1980; submitted and received on May 1, 1980; 
submitted and received on June 5, 1980; submitted on September 2, 1980, 
and received on September 8, 1980; and submitted and received on 
November 12, 1980. Included are plans to attain: The primary TSP 
standard in Greenwich and Waterbury and the carbon monoxide and ozone 
standards statewide. A program was also submitted for the review of 
construction and operation of new and modified major stationary sources 
of pollution in non-attainment areas. Certain miscellaneous provisions 
are also included.
    (12) A revision to Regulation 19-508-19(a)(2)(i), submitted by the 
Commissioner of the Connecticut Department of Environmental Protection 
on September 8, 1980, granting a variance until March 27, 1983, to the 
Federal Paperboard Company, Inc.
    (13) A comprehensive air quality monitoring plan, intended to meet 
requirements of 40 CFR part 58, was submitted by the Connecticut 
Department of Environmental Protection Commission on June 9, 1980, and 
November 17, 1980.
    (14) Non-regulatory additions to the plan which were submitted on 
December 19, 1980, and amended on March 11, 1981, by the Connecticut 
Department of Environmental Protection amending the sulfur control 
strategy to include an ``Air Pollution Control/Energy Trade Option'' 
except for submittal attachments 1 and 2, ``Sulfur Dioxide'' and 
``Transport of Sulfur Dioxide'' and the section of attachment 3 
``Control of Sulfur Oxides'' entitled ``Sample Analysis of a Btu Bubble 
Application''.
    (15) Non-regulatory addition to the plan of the state New Source 
Ambient Impact Analysis Guideline, for use in State program actions, 
submitted on December 19, 1980, and amended on March 11, 1981, and July 
15, 1981.
    (16) Revisions to regulation 19-508-4 (source monitoring 
requirements) and regulation 19-508-5 (stack emissions testing) 
submitted on November 7, 1977, by the Commissioner of the Connecticut 
Department of Environmental Protection.
    (17) A revision to Regulation 19-508-19(a)(2)(i), submitted by the 
Commissioner of the Connecticut Department of Environmental Protection 
on June 23, 1981, granting a temporary variance to Uniroyal Chemical, 
Division of Uniroyal, Inc.
    (18) Revisions to Regulation 19-508-19 (Control of Sulfur Compound 
Emissions), Regulation 19-508-24 (Connecticut Primary and Secondary 
Standards), and accompanying narrative submitted by the Commissioner of 
the Connecticut Department of Environmental Protection on October 23, 
1981, and November 4, 1981.
    (19) Revisions submitted by the Commissioner of the Connecticut 
Department of Environmental Protection on

[[Page 225]]

November 16, 1981. These provisions supersede portions of the revisions 
identified under paragraph (c)(18).
    (20) Revisions to meet the requirements of part D and certain other 
sections of the Clean Air Act, as amended, were submitted on December 
15, 1980, May 29, 1981, and May 5, 1982. Included are changes to the 
State Ozone Control Plan involving adoption of Regulation 19-508-20(k) 
controlling the use of cutback asphalt, the approval of the RFP 
demonstration for ozone attainment, a refined inventory of miscellaneous 
stationary sources of Volatile Organic Compounds, changes to Regulation 
19-508-3(1) dealing with review of new and modified stationary sources, 
and an amendment to the State's Smoke and Opacity monitoring 
requirements.
    (21) [Reserved]
    (22) Revisions to the narrative and State Regulation 19-508-18, 
subparts (d), f(1), f(2), and part of f(3), governing total suspended 
particulate emissions, submitted by the Commissioner of the Connecticut 
Department of Environmental Protection on April 8, 1982.
    (23) Regulation 19-508-20(cc), Alternative Emission Reductions as it 
applies to Regulation 19-508-20: (m), can coating; (n), coil coating; 
(o), fabric and vinyl coating; (p), metal furniture coating; (q), paper 
coating; (r), wire coating; (s), miscellaneous metal parts; (t), 
manufacture of synthesized pharmaceutical products and (v), graphic 
arts--rotogravure and flexography, was submitted on December 15, 1980, 
and January 11, 1982, by the Commissioner of the Department of 
Environmental Protection.
    (24) Revision for Sikorsky Aircraft Division of United Technologies 
received from the Commissioner of the Connecticut Department of 
Environmental Protection on June 2 and July 16, 1982. This provision 
supersedes a portion of the revisions identified under (c)(18).
    (25) Revisions to meet ozone attainment requirements of Part D 
(Group II CTG regulations), the adoption of a lead standard and the 
revision of the ozone standard, submitted on December 15, 1980, are 
approved as follows: Regulations 19-508-20 (s), (t), (v), (w), (aa), 
(bb), and (dd), Regulation 19-508-8 and Regulation 19-508-24(i)(l).
    (26) Revision for Dow Chemical U.S.A. in Gale's Ferry submitted by 
the Commissioner of the Connecticut Department of Environmental 
Protection on December 20, 1982, including state order 7002B signed on 
May 27, 1982. This provision supersedes a portion of the revisions 
identified under paragraph (c)(18).
    (27) Revision for Lydall and Foulds Division of Lydall, Inc., 
submitted by the Commissioner of the Connecticut Department of 
Environmental Protection on December 17, 1982, and January 5, 1983, 
allowing the facility to burn higher sulfur oil under the State Energy 
Trade Program.
    (28) Revision for Simkins Industries, Inc., in New Haven submitted 
by the Commissioner of the Connecticut Department of Environmental 
Protection on January 19, 1983, allowing the facility to burn higher 
sulfur oil under the Sulfur Energy Trade Program.
    (29) Attainment plan revisions to meet the requirements of Part D 
for ozone were submitted by the Department of Environmental Protection 
on December 10, 1982, and May 19, 1983. These revisions control volatile 
organic compound (VOC) emissions from solvent metal cleaners through 
emission limitations contained in Regulation 19-508-20(1) and supporting 
narrative committing the DEP to implement an educational program for 
automobile repair facilities. Approval of these revisions allowed EPA to 
rescind the moratorium on construction and modification of major sources 
of VOCs which had been in effect since October 1982.
    (30) Revision for Loomis Institute in Windsor, submitted by the 
Commissioner of the Connecticut Department of Environmental Protection 
on March 30 and July 13, 1983, allowing the facility to burn 2.0 percent 
sulfur oil under the Sulfur Energy Trade Program.
    (31) Revisions demonstrating the attainment and maintenance of the 
lead standard were submitted on October 18, 1983.
    (32) Attainment plan revisions to meet the requirements of part D 
for ozone and carbon monoxide were submitted by the Department of 
Environmental Protection on December 10, 1982, January 7, 1983, January 
21, 1983,

[[Page 226]]

May 19, 1983, June 15, 1983, September 19, 1983, and December 15, 1983. 
The revisions control volatile organic compound (VOC) and carbon 
monoxide emissions through a mix of stationary and mobile source 
controls. EPA approval includes the following regulatory provisions:
    (i) Regulation 22a-174-20(ee) limiting emissions from major nonCTG 
source categories, and
    (ii) Regulations 22a-174-27 and 14-164c describing the requirements 
for Connecticut's motor vehicle Inspection and Maintenance Program.
    (33) Revision to Regulation 19-508-20(cc), ``Alternative Emission 
Reductions'' [made part of the SIP under paragraph (c)(23) of this 
section] to add Regulation 19-508-20(ee) to the list of VOC regulations 
that may be met by bubbling under Connecticut's generic rule after 
source-specific RACT determinations have been made part of the SIP. 
Revisions requiring sources subject to Regulation 19-508-20(ee) to 
comply with 19-508-20 (aa), (bb), and (dd). These revisions were 
submitted by the Connecticut Department of Environmental Protection on 
September 20, 1983.
    (34) Revisions to the Ozone Attainment Plan were submitted by the 
Commissioner of the Connecticut Department of Environmental Protection 
on April 22, 1985.
    (i) Incorporation by reference.
    (A) Amendments to Regulation 22a-174-1, Definitions; Regulation 22a-
174-20(a), Storage of Volatile Organic Compounds; Regulation 22a-174-
20(b), Loading of Gasoline and Other Volatile Organic Compounds; and 
Regulation 22a-174-20(k), Restrictions on Cutback Asphalt, effective 
December 17, 1984.
    (ii) Additional material.
    (A) Source Test Guidelines and Procedures.
    (B) Workshop Manual for Gasoline Tank Truck Certification.
    (C) Appendix B of Control of Volatile Organic Compound Leaks from 
Gasoline Tank Trucks and Vapor Collection Systems (EPA-450/2-78-051).
    (35) Revisions to the State Implementation Plan were submitted 
December 15, 1980, and May 16, 1985, by the Commissioner of the 
Department of Environmental Protection.
    (i) Incorporation by reference.
    (A) Amendments to Department of Environmental Protection Regulation 
19-508-24(a)(4), ``Acceptable Method'' adopted by the State on October 
8, 1980.
    (ii) Additional material.
    (A) A letter dated May 16, 1985, certifying that an ``Acceptable 
Method'' shall be interpreted to mean that any monitoring method used to 
collect ambient air pollution data used for attainment status evaluation 
or designation must be approved by EPA.
    (36) Revision to the State Implementation Plan submitted on April 
18, 1986, by the Commissioner of the Department of Environmental 
Protection.
    (i) Incorporated by reference:
    (A) State Order No. 943 for Connecticut Charcoal Co., effective 
April 18, 1986, establishing and requiring reasonably available control 
technology for the control of volatile organic compounds from this 
facility.
    (37) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on April 18, 1986, 
and February 3, 1987.
    (i) Incorporation by reference.
    (A) State Order No. 944 for King Industries, Inc. dated April 18, 
1986, which establishes and requires reasonably available control 
technology for the control of volatile organic compounds from this 
facility.
    (B) A letter from the Connecticut Department of Environmental 
Protection dated February 3, 1987, which states that the effective date 
of State Order No. 944 is May 28, 1986.
    (38) Revisions to the State Implementation Plan were submitted by 
the Connecticut Department of Environmental Protection (DEP) on April 
14, 1987.
    (i) Incorporation by reference.
    (A) Letter dated April 14, 1987, from the Connecticut Department of 
Environmental Protection submitting revisions to the State 
Implementation Plan for EPA approval.
    (B) Letter dated April 1, 1987, from the Secretary of State of 
Connecticut to EPA.
    (C) Section 22a-174-20(x) of Connecticut's Regulations for the 
Abatement of Air Pollution titled, ``Control of Volatile Organic 
Compound Leaks from

[[Page 227]]

Synthetic Organic Chemical & Polymer Manufacturing Equipment,'' 
effective April 1, 1987.
    (D) Section 22a-174-20(y) of Connecticut's Regulations for the 
Abatement of Air Pollution titled, ``Manufacture of Polystyrene 
Resins,'' effective April 1, 1987.
    (E) Amendments to subsection 22a-174-20(bb) of Connecticut's 
Regulations for the Abatement of Air Pollution titled, ``Compliance 
Methods,'' effective April 1, 1987.
    (ii) Additional material.
    (A) Letter from the Connecticut DEP dated July 3, 1986, committing 
the Connecticut DEP to use only EPA approved test methods when requiring 
the testing of sources emitting volatile organic compound emissions.
    (B) Letter from the Connecticut DEP dated May 29, 1987, certifying 
that there are no polypropylene or high-density polyethylene 
manufacturers in the State of Connecticut.
    (39) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on August 24, 1987.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated August 24, 1987, submitting a revision to the 
Connecticut State Implementation Plan.
    (B) State Order No. 8007 for Belding Corticelli Thread Company dated 
July 13, 1987.
    (40) [Reserved]
    (41) Revision to the Connecticut State Implementation Plan submitted 
by the Commissioner of the Department of Environmental Protection on 
February 3, 1987.
    (i) Incorporation by reference.
    (A) A letter from the Connecticut Department of Environmental 
Protection dated February 3, 1987, which states that the effective date 
of State Order No. 943, approved previously, for Connecticut Charcoal 
Co. is May 28, 1986.
    (42) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on October 27, 1987.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated October 27, 1987, submitting a revision to the 
Connecticut State Implementation Plan.
    (B) State Order No. 8013 and attached Compliance Timetable for 
Raymark Industries, Incorporated in Stratford, Connecticut effective on 
September 24, 1987.
    (ii) Additional material.
    (A) Technical Support Document prepared by the Connecticut 
Department of Environmental Protection providing a complete description 
of the reasonably available control technology determination imposed on 
the facility.
    (43) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on February 5, 1988.
    (i) Incorporation by reference. (A) Letter from the Connecticut 
Department of Environmental Protection dated February 5, 1988, 
submitting a revision to the Connecticut State Implementation Plan.
    (B) State Order No. 8012 and attached Compliance Timetable, Appendix 
A (allowable limits on small, uncontrolled vents), and Appendix B 
(fugitive leak detection program) for American Cyanamid Company in 
Wallingford, Connecticut. State Order No. 8012 was effective on January 
6, 1988.
    (ii) Additional material. (A) Technical Support Document prepared by 
the Connecticut Department of Environmental Protection providing a 
complete description of the reasonably available control technology 
determination imposed on the facility.
    (44) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on August 31, 1987.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated August 31, 1987, submitting a revision to the 
Connecticut State Implementation Plan.
    (B) State Order No. 8008 and attached Compliance Timetable and 
Appendix A (allowable limits by product classification) for Spongex 
International, Ltd. in Shelton, Connecticut. State Order No. 8008 was 
effective on August 21, 1987.
    (ii) Additional materials.
    (A) Technical Support Document prepared by the Connecticut 
Department of Environmental Protection providing

[[Page 228]]

a complete description of the reasonably available control technology 
determination imposed on the facility.
    (45) [Reserved]
    (46) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on July 26, 1988.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated July 26, 1988, submitting a revision to the Connecticut 
State Implementation Plan.
    (B) State Order No. 8023 and attached Compliance Timetable for New 
Departure Hyatt, Division of General Motors Corporation in Bristol, 
Connecticut. State Order No. 8023 was effective on July 8, 1988.
    (ii) Additional material.
    (A) Technical Support Document prepared by the Connecticut 
Department of Environmental Protection providing a complete description 
of the reasonably available control technology determination imposed on 
the facility.
    (47) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on November 5, 1987.
    (i) Incorporation by reference. (A) Letter from the Connecticut 
Department of Environmental Protection dated November 5, 1987, 
submitting a revision to the Connecticut State Implementation Plan.
    (B) State Order No. 8001 and attached Compliance Timetable for 
Frismar, Incorporated in Clinton, Connecticut. State Order No. 8001 was 
effective on October 20, 1987.
    (ii) Additional material. (A) Technical Support Document prepared by 
the Connecticut Department of Environmental Protection providing a 
complete description of the alternative reasonably available control 
technology determination imposed on the facility.
    (48) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on December 5, 1988.
    (i) Incorporation by reference. (A) Letter from the Connecticut 
Department of Environmental Protection dated December 5, 1988, 
submitting a revision to the Connecticut State Implementation Plan.
    (B) State Order No. 8011 and attached Compliance Timetable and 
Appendix A (allowable limits by product classification) for Dow 
Chemical, U.S.A. in Gales Ferry, Connecticut. State Order No. 8011 was 
effective on October 27, 1988.
    (ii) Additional material. (A) Technical Support Document prepared by 
the Connecticut Department of Environmental Protection providing a 
complete description of the reasonable available control technology 
determination imposed on the facility.
    (49) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on January 11, 1989.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated January 11, 1989, submitting a revision to the 
Connecticut State Implementation Plan.
    (B) State Order No. 8010 and attached Compliance Timetable for 
Stanadyne, Incorporated in Windsor, Connecticut. State Order No. 8018 
was effective on January 3, 1989.
    (ii) Additional material.
    (A) Technical Support Document prepared by the Connecticut 
Department of Environmental Protection providing a complete description 
of the reasonably available control technology determination imposed on 
the facility.
    (50) Revisions to federally approved section 22a-174-20(a) of the 
Regulations of Connecticut State Agencies, submitted on January 27, 
1989, by the Department of Environmental Protection, limiting the 
volatility of gasoline from May 1 through September 15, beginning 1989 
and continuing every year thereafter, including any waivers to such 
limitations that Connecticut may grant. In 1989, the control period will 
begin on June 30.
    (51) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection (DEP) on April 7, 
1989.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut DEP dated April 7, 1989, submitting 
a revision to the Connecticut State Implementation Plan.
    (B) State Order No. 8014 and attached Compliance Timetable for Pratt 
&

[[Page 229]]

Whitney Division of United Technologies Corporation in East Hartford, 
Connecticut. State Order No. 8014 was effective on March 22, 1989.
    (C) State Order No. 8027 and attached Compliance Timetable for Pratt 
& Whitney Division of United Technologies Corporation in North Haven, 
Connecticut. State Order No. 8027 was effective on March 31, 1989.
    (ii) Additional material.
    (A) Technical Support Document prepared by the Connecticut DEP 
providing a complete description of the reasonably available control 
technology determination imposed on Pratt and Whitney's East Hartford 
facility.
    (B) Technical Support Document prepared by the Connecticut DEP 
providing a complete description of the reasonably available control 
technology determination imposed on Pratt and Whitney's North Haven 
facility.
    (52) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on February 7 and 
August 30, 1989.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated February 7, 1989, submitting a revision to the 
Connecticut State Implementation Plan.
    (B) State Order No. 8021 and attached Compliance Timetable, and 
Appendix A (allowable limits on small, uncontrolled vents and allowable 
outlet gas temperatures for surface condensers) for Pfizer, Incorporated 
in Groton, Connecticut. State Order No. 8021, Compliance Timetable and 
Appendix A were effective on December 2, 1988.
    (C) Letter from the Connecticut Department of Environmental 
Protection dated August 30, 1989, and reorganized Appendix C (fugitive 
leak detection program) and Appendix D (operation and maintenance 
program for pollution abatement equipment) to State Order No. 8021. 
Appendices C and D were effective on December 2, 1988.
    (ii) Additional material.
    (A) Technical Support Document prepared by the Connecticut 
Department of Environmental Protection providing a complete description 
of the reasonably available control technology determination imposed on 
the facility.
    (53) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on September 8, 1989.
    (i) Incorporation by reference. (A) Letter from the Connecticut 
Department of Environmental Protection dated September 8, 1989, 
submitting a revision to the Connecticut State Implementation Plan.
    (B) State Order No. 8009 and attached Compliance Timetable, Appendix 
A, Appendix B, and Appendix C for Uniroyal Chemical Company, Inc. in 
Naugatuck, Connecticut. State Order No. 8009 was effective on September 
5, 1989.
    (ii) Additional material. (A) Technical Support Document prepared by 
the Connecticut Department of Environmental Protection providing a 
complete description of the reasonably available control technology 
determination imposed on the facility.
    (54) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on December 22, 1989.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated December 22, 1989, submitting a revision to the 
Connecticut State Implementation Plan.
    (B) State Order No. 8029, attached Compliance Timetable, and Tables 
A through I for Hamilton Standard Division of United Technologies 
Corporation in Windsor Locks, Connecticut. State Order No. 8029 was 
effective on November 29, 1989.
    (ii) Additional material.
    (A) Technical Support Document prepared by the Connecticut DEP 
providing a complete description of the reasonably available control 
technology determination imposed on Hamilton Standard.
    (55) Revision to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on January 10, 1990.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated January 10, 1990, submitting a revision to the 
Connecticut State Implementation Plan.

[[Page 230]]

    (B) State Order No. 8032 and attached Compliance Timetable for the 
Heminway & Bartlett Manufacturing Company in Watertown, Connecticut. 
State Order No. 8032 was effective on November 29, 1989.
    (ii) Additional material.
    (A) Technical Support Document prepared by the Connecticut DEP 
providing a complete description of the reasonably available control 
technology determination imposed on The Heminway & Bartlett 
Manufacturing Company.
    (56) Revisions of the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on January 19, 1989, 
July 28, 1989, and January 26, 1990 (with attached letter of November 
28, 1989).
    (i) Incorporation by reference.
    (A) Letters from the Connecticut Department of Environmental 
Protection dated January 19, 1989, July 28, 1989, and January 26, 1990, 
(with attached letter of November 28, 1989) submitting revisions to the 
Connecticut State Implementation Plan.
    (B) Section 22a-174-1 of the Regulations of the Connecticut State 
Agencies Concerning Abatement of Air Pollution entitled ``Definitions,'' 
effective in the State of Connecticut on October 3, 1989.
    (C) Subsection 22a-174-3(k) of the Regulations of the Connecticut 
State Agencies Concerning Abatement of Air Pollution entitled 
``Requirements for the Prevention of Significant Deterioration (PSD) 
Program,'' effective in the State of Connecticut on October 3, 1989.
    (D) Section 22a-174-2, subsections 22a-174-3(a) through (j) and (l), 
subsection 22a-174-8(c), subsection 22a-174-20(ee), and subsection 22a-
174-4(d) of the Regulations of the Connecticut State Agencies Concerning 
Abatement of Air Pollution entitled ``Permits to Construct and Permits 
to Operate Stationary Sources or Modifications,'' effective in the State 
of Connecticut on February 1, 1989.
    (E) Connecticut's Ambient Impact Analysis Guideline dated July 1989 
as revised by letter on January 26, 1990.
    (ii) Additional materials.
    (A) State Implementation Plan narrative entitled ``New Source 
Review.''
    (B) Letter from the Connecticut Department of Environmental 
Protection regarding implementation of BACT.
    (C) Nonregulatory portions of the State Submittal.
    (57) [Reserved]
    (58) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on November 9, 1989, 
and September 12, 1991.
    (i) Incorporation by reference. (A) Letters from the Connecticut 
Department of Environmental Protection dated November 9, 1989, and 
September 12, 1991, submitting revisions to the Connecticut State 
Implementation Plan.
    (B) Section 22a-174-20 of the Regulations of the Connecticut 
Department of Environmental Protection Concerning Abatement of Air 
Pollution, effective October 31, 1989, except for the last sentence of 
22a-174-20(aa)(7).
    (59) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on March 24 and April 
23, 1992.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated April 14, 1992, submitting a revision to the 
Connecticut State Implementation Plan.
    (B) State Order No. 1073B and attached compliance timetable for the 
Stone Connecticut Paperboard Corporation of Uncasville, CT. State Order 
No. 1073B was effective on February 14, 1992.
    (C) Letter from the Connecticut Department of Environmental 
Protection dated March 24, 1992, submitting a revision to the 
Connecticut State Implementation Plan.
    (D) State Order No. 7016A and attached compliance timetable for the 
Hartford Hospital of Hartford, CT. State Order No. 7016A was effective 
on February 5, 1992.
    (ii) Additional materials.
    (A) Memorandum dated August 17, 1989, approving the modeling 
analysis for the Stone Container Co.
    (B) Modeling Study dated August 9, 1989, for the Stone Container Co.
    (C) State Order No 1073A, dated June 12, 1990, and effective July 9, 
1990.

[[Page 231]]

    (D) Memorandum dated January 3, 1990, approving the modeling 
analysis for the Hartford Hospital.
    (E) Modeling study dated December 28, 1989, for the Hartford 
Hospital.
    (60) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on February 16, 1996.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated February 16, 1996, submitting a revision to the 
Connecticut State Implementation Plan.
    (B) State Order No. 8010 dated October 25, 1989 for Sikorsky 
Aircraft Corporation, effective on January 29, 1990, as well as Addendum 
A and Addendum B to Order No. 8010, effective on February 7, 1996 and 
September 29, 1995, respectively. The State order and two addenda define 
and impose RACT on certain VOC emissions at Sikorsky Aircraft 
Corporation in Stratford, Connecticut
    (61) Revisions to the State Implemetation Plan submitted by the 
Connecticut Department of Environmental Protection on February 28, 1991.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated February 28, 1991, submitting a revision to the 
Connecticut State Implementation Plan.
    (B) State Order No. 7017 and attached compliance timetable for the 
Connecticut Light and Power Company of Montville, Connecticut. State 
Order No. 7017 was effective on February 25, 1991.
    (ii) Additional materials.
    (A) Memorandum dated September 14, 1990, approving the modeling 
analysis for Connecticut Light and Power.
    (B) Letter dated April 23, 1991, confirming that the revised 
configuration approved by State Order No. 7017 will not lead to 
violations.
    (C) Modeling Study dated January 26, 1990, for Connecticut Light and 
Power.
    (62) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on January 12, 1993.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection, dated January 12, 1993, submitting a revision to the 
Connecticut State Implementation Plan.
    (B) Section 22a-174-30 of the Connecticut Regulations for the 
Abatement of Air Pollution, entitled ``Dispensing of Gasoline/Stage II 
Vapor Recovery,'' dated November 1992.
    (C) Letter from the Connecticut Secretary of State's office 
indicating that the regulation entitled ``Dispensing of Gasoline/Stage 
II Vapor Recovery'' became effective on November 24, 1992.
    (ii) Additional materials.
    (A) Nonregulatory portions of the submittal.
    (B) Connecticut Department of Environmental Protection document 
entitled ``Narrative of SIP Revision: Stage II Vapor Recovery,'' dated 
January 1993.
    (63) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on March 11, 1993.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated March 11, 1993, submitting a revision to the 
Connecticut State Implementation Plan.
    (B) Connecticut State Order No 7019 dated March 11, 1993, and 
effective in the State of Connecticut on February 19, 1993.
    (ii) Additional materials.
    (A) Air Quality Modeling Analysis to Demonstrate SO2 
CAAQS/NAAQS Compliance at the Hamilton Standard Division of United 
Technologies Corporation Windsor Locks CT; June 1991.
    (64) [Reserved]
    (65) Revisions to the State Implementation Plan establishing a Small 
Business Stationary Source Technical and Environmental Compliance 
Assistance Program were submitted by the Connecticut Department of 
Environmental Protection on January 12 and August 9, 1993.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated January 12, 1993, submitting a revision to the 
Connecticut State Implementation Plan.

[[Page 232]]

    (B) Revisions to the State Implementation Plan for the Small 
Business Stationary Source Technical and Environmental Compliance 
Assistance Program dated January 1993 and effective on January 12, 1993.
    (C) Letter from the Connecticut Department of Environmental 
Protection dated August 9, 1993, clarifying and updating the January 12, 
1993, submittal.
    (ii) Additional materials.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated April 6, 1994, clarifying the January 12, 1993, 
submittal.
    (B) Other non-regulatory portions of the State's submittal.
    (66) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on January 12, 1993.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated January 12, 1993 submitting a revision to the 
Connecticut State Implementation Plan.
    (B) Section 22a-174-4(c)(1) of Connecticut Regulations for the 
Abatement of Air Pollution, under the section entitled ``Recordkeeping 
and Reporting.'' Section 22a-174-4(c)(1) was previously numbered as 19-
508-4(c)(1) in Connecticut's SIP. 19-508-4(c)(1) in Connecticut's SIP. 
19-508-4 became effective in the State of Connecticut on October 31, 
1977. Connecticut developed an emission statement program using the 
existing regulatory authority given by section 22a-174-4(c)(1) under the 
section entitled ``Reporting and Recordkeeping''.
    (ii) Additional information.
    (A) State implementation Plan narrative entitled ``Revision to State 
Implementation Plan for Air Quality Emission Statements'' which 
addresses emission statement requirements not discussed specifically in 
Section 22a-174-4(c)(1).
    (B) Nonregulatory portions of the submittal.
    (67)  [Reserved]
    (68) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on March 24, 1994, 
May 20, 1994, and March 4, 1994.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated March 24, 1994 submitting a revision to the Connecticut 
State Implementation Plan.
    (B) Letter from the Connecticut Department of Environmental 
Protection dated May 20, 1994 submitting a supplemental revision to the 
Connecticut State Implementation Plan.
    (C) State Order No. 8073: State of Connecticut vs. City of New Haven 
(effective September 24, 1993) and attached plan titled ``Remedial 
Action Plan for Prevention of Airborne Particulate Matter and Fugitive 
Discharge of Visible Emissions in the Alabama Street/East Shore Parkway 
Area of New Haven.''
    (D) State Order No. 8074: State of Connecticut vs. Waterfront 
Enterprises, Inc. (effective November 5, 1993) and attached plan titled 
``Proposed Operation Plan in Response to Unilateral Order (September 20, 
1993).''
    (E) State Order No. 8075: State of Connecticut vs. Laydon 
Construction, (effective September 21, 1993) and attached plan titled 
``Plan for Control of Fugitive Emissions of PM10 (September 21, 1993).''
    (F) State Order No. 8076: State of Connecticut vs. United 
Illuminating Company (effective December 2, 1993) and attached plan 
titled ``Remediation Plan for Fugitive Emissions: Alabama Street and 
Connecticut Avenue, New Haven, Connecticut (November 19, 1993).''
    (G) State Order No. 8076c: State of Connecticut vs. M. J. Metals, 
Inc. (effective June 18, 1993).
    (H) State Order No. 8078: State of Connecticut vs. New Haven 
Terminal, Inc. (effective November 15, 1993) and attached plan titled 
``Fugitive Dust Control Plan (Revised January 19, 1994).''
    (I) State Order No. 8079: State of Connecticut vs. Yankee Gas 
Services Company (effective September 24, 1993) and attached plan titled 
``Revised Compliance Plan for Consent Order No. 8079 (August 31, 
1993).''
    (J) Letter from the Connecticut Department of Environmental 
Protection dated March 4, 1994 (received March 16, 1995) submitting two 
amendments to the Regulations of Connecticut State

[[Page 233]]

Agencies concerning abatement of air pollution: amended Sections 22a-
174-24(f) and -24(g) ``Connecticut primary and secondary ambient air 
quality standards for particulate matter'' and amended Sections 22a-174-
6(a) and -6(b) `` `Air Pollution' emergency episode procedures'' (both 
effective July 7, 1993).
    (K) Amended Regulations of Connecticut State Agencies: amended 
Sections 22a-174-24(f) and -24(g) ``Connecticut primary and secondary 
ambient air quality standards for particulate matter'' and amended 
Sections 22a-174-6(a) and -6(b) `` `Air Pollution' emergency episode 
procedures'' (both effective July 7, 1993).
    (ii) Additional materials.
    (A) An attainment plan and demonstration which outlines 
Connecticut's control strategy and for attainment and maintenance of the 
PM10 NAAQS, implements and meets RACM and RACT requirements, and 
provides contingency measures for New Haven.
    (B) Nonregulatory portions of the submittal.
    (69) Connecticut submitted the Oxygenated Gasoline Program and 
revisions on January 11, 1993, January 12, 1993, January 14, 1993, and 
August 1, 1995. This submittal satisfied the requirements of section 
211(m) of the Clean Air Act, as amended.
    (i) Incorporation by reference.
    (A) Letters dated January 11, 1993 and January 12, 1993 which 
included the oxygenated gasoline program, Regulations of Connecticut 
State Agencies (RCSA) Section 22a-174-28, with an effective date of 
November 2, 1992.
    (B) A letter dated January 14, 1993 requesting that the RCSA Section 
22a-174-28, as submitted on January 11, 1993 and January 12, 1993, be 
adopted as part of Connecticut's SIP.
    (C) A letter dated August 1, 1995, requesting that a revision to 
RCSA Section 22a-174-28(a), with an effective date of July 26, 1995, be 
approved and adopted as part of Connecticut's SIP.
    (ii) Additional materials.
    (A) The Technical Support Document for the Redesignation of the 
Hartford Area as Attainment for Carbon Monoxide submitted on September 
30, 1994.
    (B) Nonregulatory portions of submittals.
    (70) Revision to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on January 13, 1995.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated January 13, 1995 submitting a revision to the 
Connecticut State Implementation Plan.
    (B) Amended Regulation of Connecticut State Agencies: amended 
Subsection 22a-174-3(k) ``Abatement of air pollution--New Source 
Review'' (effective December 2, 1994).
    (ii) Additional materials.
    (A) Nonregulatory portions of the submittal.
    (71) Revisions to the Connecticut State Implementation Plan (SIP) 
for carbon monoxide concerning the control of carbon monoxide from 
mobile sources, dated January 12, 1993, January 14, 1993, April 7, 1994, 
and August 1, 1995 submitted by the Connecticut Department of 
Environmental Protection (CT DEP).
    (i) Incorporation by reference.
    (A) Letter dated August 1, 1995 which included the amendments and 
revisions to the Regulation of Connecticut State Agencies (RCSA), 
Section 22a-174-28(a) regarding the definition for the Southwestern 
Control Area and that portion of the definition of ``control period'' 
that applies to the Southwestern Control Area with an effective date of 
July 26, 1995.
    (ii) Additional materials.
    (A) January 12, 1993 and April 7, 1994, VMT forecasts beginning with 
the year 1993 and including all subsequent years up to the year of 
attainment (1995).
    (B) January 12, 1993 and April 7, 1994, Carbon Monoxide Attainment 
Demonstration and Contingency Measures.
    (72) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on: May 18, 1995; 
August 21, 1995; January 17, 1996; January 30, 1996; January 30, 1996; 
January 30, 1996; January 30, 1996; June 17, 1996; June 20, 1996; June 
24, 1996; July 9, 1996; July 11, 1996; February 18, 1997; March 20, 
1997; March 24, 1997; March 24, 1997; March 24, 1997; March 24, 1997; 
March 24, 1997; April 22, 1997; April 22, 1997; May 19, 1997; May 19, 
1997; and May 20, 1997.

[[Page 234]]

    (i) Incorporation by reference.
    (A) Twenty-four letters from the Connecticut Department of 
Environmental Protection dated: May 18, 1995; August 21, 1995; January 
17, 1996; June 24, 1996; January 30, 1996; January 30, 1996; January 30, 
1996; January 30, 1996; June 20, 1996; June 17, 1996; July 11, 1996; 
July 9, 1996; March 24, 1997; May 19, 1997; March 24, 1997; March 20, 
1997; March 24, 1997; February 18, 1997; May 19, 1997; March 24, 1997; 
March 24, 1997; May 20, 1997; April 22, 1997; and April 22, 1997; 
submitting revisions to the Connecticut State Implementation Plan.
    (B) Connecticut Trading Agreement and Order no. 8092 issued to 
United Illuminating Company's Station #3 in Bridgeport, effective on May 
18, 1995.
    (C) Connecticut Trading Agreement and No. 8095 issued to American 
Ref-Fuel Company of Southeastern Connecticut in Preston, effective on 
June 2, 1995.
    (D) Connecticut Trading Agreement and Order no. 8093 issued to 
Pfizer, Inc., in Groton, effective on July 19, 1995.
    (E) Connecticut Trading Agreement and Order no. 8096 issued to Food 
Ingredients Company in New Milford, effective on August 25, 1995.
    (F) Connecticut Trading Agreement and Order no. 8106 issued to 
Connecticut Light and Power Company in Middletown, effective on October 
10, 1995.
    (G) Connecticut Trading Agreement and Order no. 8107 issued to 
Northeast Nuclear Energy Company in Waterford, effective on October 13, 
1995.
    (H) Connecticut Trading Agreement and Order no. 8105 issued to 
Electric Boat Division of General Dynamics in Groton, effective on 
October 31, 1995.
    (I) Connecticut Trading Agreement and Order no. 8100 issued to 
Bridgeport RESCO Company in Bridgeport, effective on November 2, 1995.
    (J) Connecticut Trading Agreement and Order no. 8102 issued to 
United Illuminating's auxiliary boiler in New Haven, effective on 
December 15, 1995.
    (K) Connecticut Trading Agreement and Order no. 8103 issued to 
United Illuminating Company's Station #4 in New Haven, effective on 
February 14, 1996.
    (L) Connecticut Trading Agreement and Order no. 8119 issued to the 
City of Norwich, Department of Public Utilities, effective on March 4, 
1996.
    (M) Connecticut Trading Agreement and Order no. 8118 issued to South 
Norwalk Electric Works, South Norwalk, effective on March 19, 1996.
    (N) Connecticut Trading Agreement and Order no. 8101 issued to the 
State of Connecticut Department of Mental Health and Addiction Services, 
effective on July 16, 1996.
    (O) Connecticut Trading Agreement and Order no. 8110 issued to Yale 
University, effective on July 29, 1996.
    (P) Connecticut Trading Agreement and Order no. 8132 issued to 
Bridgeport Hospital, effective on September 10, 1996.
    (Q) Connecticut Trading Agreement and Order no. 1494 issued to 
Connecticut Light and Power, involving Branford, Cos Cob, Devon, 
Franklin Drive, Montville, Middletown, South Meadow, Torrington, Tunnel 
Road, and Norwalk Harbor Stations, effective on October 15, 1996.
    (R) Connecticut Trading Agreement and Order no. 8130 issued to the 
State of Connecticut Department of Public Works, effective on October 
18, 1996.
    (S) Connecticut Trading Agreement and Order no. 8115 issued to the 
University of Connecticut in Storrs, effective on November 19, 1996.
    (T) Connecticut Trading Agreement and Order no. 8113 issued to 
Simkins Industries, effective on November 19, 1996.
    (U) Connecticut Trading Agreement and Order no. 8135 issued to 
Bridgeport Hydraulic Company, effective on December 24, 1996.
    (V) Connecticut Trading Agreement and Order no. 8141 issued to the 
Town of Wallingford Department of Public Utilities, effective on 
December 27, 1996.
    (W) Regulations 22a-174-22 ``Control of Nitrogen Oxides Emissions,'' 
adopted on January 23, 1997, which establishes reasonably available 
control technology requirements for major stationary sources of nitrogen 
oxides.
    (X) Connecticut Trading Agreement and Order no. 8123 issued to the 
Algonquin Gas Transmission Company, effective on April 18, 1997.

[[Page 235]]

    (Y) Connecticut Trading Agreement and Order no. 8116 issued to the 
Connecticut Resource Recovery Authority, effective on April 22, 1997.
    (ii) Additional materials.
    (A) Letter, dated June 18, 1996, from Carmine DiBattista, Chief of 
the Bureau of Air Management for the Connecticut DEP, to Susan Studlien, 
Deputy Director of the Office of Ecosystem Protection at U.S. EPA, 
Region I.
    (B) SIP narrative materials, dated May 1995, submitted with 
Connecticut Trading Agreement and Order no. 8092 for United Illuminating 
Company's Station #3 in New Haven.
    (C) SIP narrative materials, dated August 3, 1995, submitted with 
Connecticut Trading Agreement and Order no. 8095 for American Ref-Fuel 
Company of Southeastern Connecticut in Preston.
    (D) SIP narrative materials, dated December 1995, submitted with 
Connecticut Trading Agreement and Order no. 8093 issued to Pfizer, Inc., 
in Groton.
    (E) SIP narrative materials, dated November 1995, submitted with 
Connecticut Trading Agreement and Order no. 8096 issued to Food 
Ingredients Company in New Milford.
    (F) SIP narrative materials, dated November 1995, submitted with 
Connecticut Trading Agreement and Order no. 8106 issued to Connecticut 
Light and Power Company in Middletown.
    (G) SIP narrative materials, dated November 1995, submitted with 
Connecticut Trading Agreement and Order no. 8107 issued to Northeast 
Nuclear Energy Company in Waterford.
    (H) SIP narrative materials, dated October 6, 1995, submitted with 
Connecticut Trading Agreement and Order no. 8105 issued to Electric Boat 
Division of General Dynamics in Groton.
    (I) SIP narrative materials, dated September 29, 1995, submitted 
with Connecticut Trading Agreement and Order no. 8100 issued to 
Bridgeport RESCO Company in Bridgeport.
    (J) SIP narrative materials, dated December 1995, submitted with 
Connecticut Trading Agreement and Order no. 8102 issued to United 
Illuminating's auxiliary boiler in New Haven.
    (K) SIP narrative materials, dated March 1996, submitted with 
Connecticut Trading Agreement and Order no. 8103 issued to United 
Illuminating Company's Station #4 in Bridgeport.
    (L) SIP narrative materials, dated May 31, 1995, submitted with 
Connecticut Trading Agreement and Order no. 8119 issued to the City of 
Norwich, Department of Public Utilities.
    (M) SIP narrative materials, dated May 31, 1995, submitted with 
Connecticut Trading Agreement and Order no. 8118 issued to South Norwalk 
Electric Works, South Norwalk.
    (N) SIP narrative materials, dated March 1997, submitted with 
Connecticut Trading Agreement and Order no. 8101 issued to the State of 
Connecticut Department of Mental Health and Addiction Services.
    (O) SIP narrative materials, dated May 1997, submitted with 
Connecticut Trading Agreement and Order no. 8110 issued to Yale 
University.
    (P) SIP narrative materials, dated March 1997, submitted with 
Connecticut Trading Agreement and Order no. 8132 issued to Bridgeport 
Hospital.
    (Q) SIP narrative materials, dated March 1997, submitted with 
Connecticut Trading Agreement and Order no. 1494 issued to Connecticut 
Light and Power, involving Branford, Cos Cob, Devon, Franklin Drive, 
Montville, Middletown, South Meadow, Torrington, Tunnel Road, and 
Norwalk Harbor Stations.
    (R) SIP narrative materials, dated March 1997, submitted with 
Connecticut Trading Agreement and Order no. 8130 issued to the State of 
Connecticut Department of Public Works.
    (S) SIP narrative materials, dated February 1996, submitted with 
Connecticut Trading Agreement and Order no. 8115 issued to the 
University of Connecticut in Storrs.
    (T) SIP narrative materials, dated May 1997, submitted with 
Connecticut Trading Agreement and Order no. 8113 issued to Simkins 
Industries.
    (U) SIP narrative materials, dated March 1997, submitted with 
Connecticut Trading Agreement and Order no. 8135 issued to Bridgeport 
Hydraulic Company.
    (V) SIP narrative materials, dated March 1997, submitted with 
Connecticut Trading Agreement and Order no.

[[Page 236]]

8141 issued to the Town of Wallingford Department of Public Utilities.
    (W) SIP narrative materials, dated April 1997, submitted with 
Connecticut Trading Agreement and Order no. 8123 issued to the Algonquin 
Gas Transmission Company.
    (X) SIP narrative materials, dated April 1997, submitted with 
Connecticut Trading Agreement and Order no. 8116 issued to the 
Connecticut Resource Recovery Authority.
    (73) Revisions to the State Implementation Plan submitted by the 
Connecticut Department of Environmental Protection on June 3, 1996.
    (i) Incorporation by reference.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated June 3, 1996, submitting a revision to the Connecticut 
State Implementation Plan.
    (B) State Order No. 8036, dated May 6, 1996, for Risdon Corporation, 
effective on that date. The State order define and impose alternative 
RACT on certain VOC emissions at Risdon Corporation in Danbury, 
Connecticut.
    (74) A revision to the Connecticut SIP regarding ozone monitoring. 
Connecticut will modify its SLAMS and its NAMS monitoring systems to 
include a PAMS network design and establish monitoring sites. 
Connecticut's SIP revision satisfies 40 CFR 58.20(f) PAMS requirements.
    (i) Incorporation by reference.
    (A) PAMS SIP Commitment Narrative, which incorporates PAMS into the 
ambient air quality monitoring network of State or Local Air Monitoring 
Stations (SLAMS) and National Air Monitoring Stations (NAMS).
    (ii) Additional material.
    (A) Letter from the Connecticut Department of Environmental 
Protection dated March 2, 1995 submitting a revision to the Connecticut 
State Implementation Plan.
[37 FR 10855, May 31, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.370, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.371  Classification of regions.

    The Connecticut plan was evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                                  Pollutant
                                                           -----------------------------------------------------
                Air quality control region                  Particulate   Sulfur   Nitrogen   Carbon
                                                               matter     oxides    dioxide  monoxide    Ozone
----------------------------------------------------------------------------------------------------------------
New Jersey-New York-Connecticut Interstate................           I          I         I         I          I
Hartford-New Haven-Springfield Interstate.................           I          I       III         I          I
Northwestern Intrastate...................................         III        III       III       III        III
Eastern Intrastate........................................          II        III       III       III        III
----------------------------------------------------------------------------------------------------------------

[37 FR 10855, May 31, 1972, as amended at 39 FR 16346, May 8, 1974; 45 
FR 84787, Dec. 23, 1980]



Sec. 52.372  Extensions.

    (a) Pursuant to section 186(a)(4) of the Clean Air Act, as amended 
in 1990, the Regional Administrator hereby extend for one year (until 
December 31, 1996) the attainment date for the New York-Northern New 
Jersey-Long Island Consolidated Metropolitan Statistical Carbon Monoxide 
nonattainment area.
    (b) The Administrator hereby extends until December 31, 1996, the 
attainment date for particulate matter for the New Haven PM10 
nonattainment area, as requested by the State of Connecticut on March 
22, 1996 and based on monitored air quality data for the national 
ambient air quality standard for PM10 during the years 1993-95.
[61 FR 56900, Nov. 5, 1996, as amended at 62 FR 14331, Mar. 26, 1997]



Sec. 52.373   Approval status.

    (a) The Administrator approves the general procedures of the state's 
sulfur control regulations (19-508-19) and accompanying narrative 
submitted on October 23, 1981, and November 4, 1981 and identified under 
Sec. 52.370(c)(18), provided that any individual source approvals 
granted by the state under the Air Pollution Control/Energy Trade

[[Page 237]]

Option and solid fuel burning permitting system are submitted to EPA as 
SIP revisions.
    (b) The Administrator approves the total suspended particulate 
regulation for foundry sand processes as submitted and identified under 
paragraph (c)(22) of this section. This includes only the requirement to 
remove ninety percent of the particulate matter and not the requirement 
to emit not more than 0.75 pounds of particulate per ton of material 
cast, a provision which may be found in state regulation 19-508-
18(f)(3).
[61 FR 38576, July 25, 1996]



Sec. 52.374  Attainment dates for national standards.

    The following table presents the latest dates by which the national 
standards are to be attained. The dates reflect the information 
presented in Connecticut's plan.

----------------------------------------------------------------------------------------------------------------
                                                                    Pollutant
                               ---------------------------------------------------------------------------------
Air quality control region and              SO2
      nonattainment area       ----------------------------     PM10           NOX           CO           O3
                                   Primary      Secondary
----------------------------------------------------------------------------------------------------------------
 AQCR 41: Eastern Connecticut
          Intrastate
Middlesex County (part).......  a             b             a             a             a            e
All portions except cities and
    towns in Hartford Area
New London County.............  a             b             a             a             a            e
Tolland County (part).........  a             b             a             a             a            e
All portions except cities and
    towns in Hartford Area
Windham County................  a             b             a             a             a            e
 AQCR 42: Hartford-New Haven-
    Springfield Interstate
     Hartford-New Britain-
        Middletown Area
Hartford County (part) See 40   a             b             a             a             d            e
 CFR 81.307.
Litchfield County (part) See    a             b             a             a             d            e
 40 CFR 81.307.
Middlesex County (part) See 40  a             b             a             a             d            e
 CFR 81.307.
Tolland County (part) See 40    a             b             a             a             d            e
 CFR 81.307.
  New Haven-Meriden-Waterbury
             Area
Fairfield County (part) See 40  a             b             a             a             d            e
 CFR 81.307.
Litchfield County (part) See    a             b             a             a             d            e
 40 CFR 81.307.
       New Haven County
All portions except City of     a             b             a             a             d            e
 New Haven.
City of New Haven.............  a             b             g             a             d            e
 AQCR 43: New York-New Jersey-
  Connecticut Interstate New
York-N. New Jersey-Long Island
             Area
Fairfield County (part) See 40  a             b             a             a             d            f
 CFR 81.307.
Litchfield County (part) See    a             b             a             a             d            f
 40 CFR 81.307.
     AQCR 44: Northwestern
    Connecticut Interstate
Hartford County (part)........  a             b             a             a             a            e
       Hartford Township
Litchfield County (part) See    a             b             a             a             a            e
 40 CFR 81.307.
All portions except cities and
 towns in Hartford, New Haven,
      and New York Areas
----------------------------------------------------------------------------------------------------------------
a. Air quality levels presently below primary standards or area is unclassifiable.
b. Air quality levels presently below secondary standards or area is unclassifiable.
c. November 15, 1995.
d. December 31, 1995.
e. November 15, 1999.
f. November 15, 2007.
g. December 31, 1996 (two 1-year extensions granted).

[45 FR 84787, Dec. 23, 1980, as amended at 61 FR 38576, July 25, 1996; 
62 FR 14331, Mar. 26, 1997]

[[Page 238]]



Sec. 52.375  Certification of no sources.

    The State of Connecticut has certified to the satisfaction of EPA 
that no sources are located in the state which are covered by the 
following Control Technique Guidelines:
    (a) Large Petroleum Dry Cleaners.
    (b) Natural Gas/Gasoline Processing Plants.
    (c) Air Oxidation Processes/SOCMI.
    (d) Manufacturers of High-density Polyethylene and Polypropylene 
Resins.
[50 FR 37178, Sept. 12, 1985, as amended at 53 FR 17936, May 19, 1988]



Sec. 52.376  Control strategy: Carbon monoxide.

    (a) Approval-On January 12, 1993, the Connecticut Department of 
Environmental Protection submitted a revision to the carbon monoxide 
State Implementation Plan for the 1990 base year emission inventory. The 
inventory was submitted by the State of Connecticut to satisfy Federal 
requirements under section 182(a)(1) of the Clean Air Act as amended in 
1990, as a revision to the carbon monoxide State Implementation Plan.
    (b) Approval-On September 30, 1994, the Connecticut Department of 
Environmental Protection submitted a request to redesignate the 
Hartford/New Britain/Middletown Area carbon monoxide nonattainment area 
to attainment for carbon monoxide. As part of the redesignation request, 
the State submitted a maintenance plan as required by 175A of the Clean 
Air Act, as amended in 1990. Elements of the section 175A maintenance 
plan include a base year (1993 attainment year) emission inventory for 
carbon monoxide, a demonstration of maintenance of the carbon monoxide 
NAAQS with projected emission inventories to the year 2005 for carbon 
monoxide, a plan to verify continued attainment, a contingency plan, and 
an obligation to submit a subsequent maintenance plan revision in 8 
years as required by the Clean Air Act. If the area records a violation 
of the carbon monoxide NAAQS (which must be confirmed by the State), 
Connecticut will implement one or more appropriate contingency 
measure(s) which are contained in the contingency plan. The menu of 
contingency measure includes enhanced motor vehicle inspection and 
maintenance program and implementation of the oxygenated fuels program. 
The redesignation request and maintenance plan meet the redesignation 
requirements in sections 107(d)(3)(E) and 175A of the Act as amended in 
1990, respectively. The redesignation meets the Federal requirements of 
section 182(a)(1) of the Clean Air Act as a revision to the Connecticut 
Carbon Monoxide State Implementation Plan for the above mentioned area.
    (c) Approval-On January 12, 1993 and April 7, 1994, the Connecticut 
Department of Environmental Protection submitted revisions to the carbon 
monoxide State Implementation Plan for VMT forecasts, contingency 
measures, and attainment demonstration for CO. These VMT forecasts, 
contingency measures, and attainment demonstration were submitted by 
Connecticut to satisfy Federal requirements under sections 187(a)(2)(A), 
187(a)(3) and 187(a)(7) of the Clean Air Act, as amended in 1990, as 
revisions to the carbon monoxide State Implementation Plan.
[60 FR 55320, Oct. 31, 1995, as amended at 61 FR 38577, July 25, 1996]



Secs. 52.377--52.379  [Reserved]



Sec. 52.380  Rules and regulations.

    (a) All facilities owned, operated or under contract with the 
Connecticut Transportation Authority shall comply in all respects with 
Connecticut Regulations for the Abatement of Air Pollution sections 19-
508-1 through 19-508-25 inclusive, as approved by the Administrator.
    (b) For the purposes of paragraph (a) of this section the word 
``Administrator'' shall be substituted for the word ``Commissioner'' 
wherever that word appears in Connecticut Regulations for the Abatement 
of Air Pollution sections 19-508-1 through 19-508-25 inclusive, as 
approved by the Administrator.
    (c) The June 27 and December 28, 1979, February 1, May 1, September 
8 and November 12, 1980, revisions are approved as satisfying Part D 
requirements under the following conditions:
    (1) [Reserved]

[[Page 239]]

    (2) Submittal by December 15, 1980, of a revision to Regulation 19-
508-20 (1) (solvent metal cleaning) to be consistent with the CTG or a 
showing that the VOC emissions in the present regulation are within five 
(5) percent of the VOC emissions which would be allowed if the CTG 
recommendations were followed.
    (d) Non-Part D-No Action: EPA is neither approving nor disapproving 
the following elements of the revisions:
    (1)-(2) [Reserved]
    (3) The program to review new and modified major stationary sources 
in attainment areas (prevention of significant deterioration).
    (4) Permit fees
    (5) Stack height regulations
    (6) Interstate pollution requirements
    (7) Monitoring requirements
    (8) Conflict of interest provisions.
    (9) Use of 1 percent sulfur content fuel by the following residual 
oil burning sources, identified under Sec. 52.370, paragraph (c)(18).
    (i) Northeast Utilities, HELCO Power Station in Middletown,
    (10) Emergency Fuel Variance provisions of Regulation 19-508-19 
(a)(2)(ii) identified under Sec. 52.370 paragraph (c)(18).
    (e) Disapprovals. (1) Regulation 19-508-19(a)(9) concerning coal use 
at educational and historical exhibits and demonstrations, identified 
under Sec. 52.370, (c)(18).
    (2) Regulation 19-508-19, subsection (a)(4)(iii)(C) and 
(a)(4)(iii)(E) concerning fuel merchants, identified under Sec. 52.370, 
paragraph (c)(18).
[40 FR 23280, May 29, 1975, as amended at 45 FR 84787, Dec, 23, 1980; 46 
FR 34801, July 6, 1981; 46 FR 56615, Nov. 18, 1981; 46 FR 62062, Dec. 
22, 1981; 47 FR 763, Jan. 7, 1982; 47 FR 36823, Aug. 24, 1982; 47 FR 
41959, Sept. 23, 1982; 47 FR 49646, Nov. 2, 1982; 47 FR 51129, Nov. 12, 
1982; 48 FR 5724, Feb. 8, 1983; 50 FR 50907, Dec. 13, 1985]



Sec. 52.381  Requirements for state implementation plan revisions relating to new motor vehicles.

    Connecticut must comply with the requirements of Sec. 51.120.
[60 FR 4737, Jan. 24, 1995]



Sec. 52.382  Significant deterioration of air quality.

    (a) The requirements of sections 160 through 165 of the Clean Air 
Act are not met, since the plan does not include approvable provisions 
for the NO2 increments under the prevention of significant 
deterioration program.
    (b) The increments for nitrogen dioxide and related requirements 
promulgated on October 17, 1988 (53 FR 40671) to 40 CFR 52.21(b) through 
(w) are hereby incorporated and made part of the applicable State 
Implementation Plan for the State of Connecticut.
[58 FR 10964, Feb. 23, 1993]



Sec. 52.383  Stack height review.

    The State of Connecticut has declared to the satisfaction of EPA 
that no existing emission limitations have been affected by stack height 
credits greater than good engineering practice or any other prohibited 
dispersion techniques as defined on EPA's stack height regulations as 
revised on July 8, 1985. Such declarations were submitted to EPA on 
February 21, 1986, and May 27, 1986.
[52 FR 49407, Dec. 31, 1987]



Sec. 52.384  Emission inventories.

    (a) The Governor's designee for the State of Connecticut submitted 
the 1990 base year emission inventories for the Connecticut portion of 
the New York-New Jersey-Connecticut severe ozone nonattainment area and 
the Hartford serious ozone nonattainment area on January 13, 1994 as 
revisions to the State's Implementation Plan (SIP). Revisions to the 
inventories were submitted on February 3, 1994 and February 16, 1995. 
The 1990 base year emission inventory requirement of section 182(a)(1) 
of the Clean Air Act, as amended in 1990, has been satisfied for these 
areas.
    (b) The inventories are for the ozone precursors which are volatile 
organic compounds, nitrogen oxides, and carbon monoxide. The inventories 
covers point, area, non-road mobile, on-road mobile, and biogenic 
sources.
    (c) Taken together, the Connecticut portion of the New York-New 
Jersey-Connecticut severe nonattainment area

[[Page 240]]

and the Hartford serious nonattainment area encompass the entire 
geographic area of the State.
[62 FR 55340, Oct. 24, 1997]



Sec. 52.385  EPA-approved Connecticut regulations.

    The following table identifies the State regulations which have been 
submitted to and approved by EPA as revisions to the Connecticut State 
Implementation Plan. This table is for informational purposes only and 
does not have any independent regulatory effect. To determine regulatory 
requirements for a specific situation, consult the plan identified in 
Sec. 52.370. To the extent that this table conflicts with Sec. 52.370, 
Sec. 52.370 governs.

[[Page 241]]



                                                         Table 52.385--EPA-Approved Regulations
--------------------------------------------------------------------------------------------------------------------------------------------------------
                                                             Dates
                                           -----------------------------------------
   Connecticut State       Title/subject                                    Date         Federal Register          Section 52.370          Comments/
        citation                               Date adopted by State    approved by          citation                                     description
                                                                            EPA
--------------------------------------------------------------------------------------------------------------------------------------------------------
19-508.................  Connecticut Air    3/3/72....................      5/31/72  37 FR 10842............  (c) 1.2................  State of CT Air
                          Implementation                                                                                                Implementation
                          Plan.                                                                                                         Plan.
                                            8/10/72...................      5/14/73  38 FR 12696............  (c) 3..................  Correction to
                                                                                                                                        submission dates
                                                                                                                                        for supplemental
                                                                                                                                        information.
                                            4/9/74....................       6/2/75  40 FR 23746............  (c) 5..................  Identification of
                                                                                                                                        Air Quality
                                                                                                                                        Maintenance
                                                                                                                                        Areas.
                                            8/10/76...................     11/29/77  42 FR 60753............  (c) 7..................  Adds carbon
                                                                                                                                        monoxide/oxidant
                                                                                                                                        control strategy
                                                                                                                                        and regulations.
                                            6/30/77...................      9/29/78  43 FR 44840............  (c) 8..................  Describes air
                                                                                                                                        quality
                                                                                                                                        surveillance
                                                                                                                                        program.
22a-171................  Small Business     1/12/93...................      5/19/94  59 FR 26123............  (c) 65.................  Established small
                          Assistance.                                                                                                   business
                                                                                                                                        compliance and
                                                                                                                                        technical
                                                                                                                                        assistance
                                                                                                                                        program.
22a-174-1..............  Definitions......  4/01/72...................      5/31/72  37 FR 23085............  (b).                     .................
                                            5/31/72...................     12/23/80  45 FR 84769............                           Adds definitions
                                                                                                                                        for PSD and NSR
                                                                                                                                        program. EPA
                                                                                                                                        took no action
                                                                                                                                        because CT did
                                                                                                                                        not submit
                                                                                                                                        regulations.
                                            12/13/84..................      7/18/85  50 FR 29229............  (c) 34.................  Revision to the
                                                                                                                                        definition of
                                                                                                                                        VOC adding 7
                                                                                                                                        nonreactive
                                                                                                                                        compounds to
                                                                                                                                        exempt list.
                                            12/27/88..................      2/23/93  58 FR 10957............  (c) 56.................  Changes
                                                                                                                                        definitions of
                                                                                                                                        ``actual
                                                                                                                                        emissions'' and
                                                                                                                                        ``potential
                                                                                                                                        emissions''
                                                                                                                                        throughout
                                                                                                                                        regulations.
22a-174-2..............  Registration       4/04/72...................      5/31/72  37 FR 23085............  (b).                     .................
                          requirements for
                          existing
                          stationary
                          sources of air
                          pollutants.
                                            8/31/79...................     12/23/80  45 FR 84769............   (c) 11................  In tandem with
                                                                                                                                        changes to
                                                                                                                                        Regulation 3,
                                                                                                                                        sources existing
                                                                                                                                        prior to 1972
                                                                                                                                        must register.
22a-174-3..............  Permits for        4/04/72...................      5/31/72  37 FR 23085............  (b)....................  Conditional
                          construction and                                                                                              approval of NSR
                          operation of                                                                                                  program.
                          stationary
                          sources.
                                            8/30/79...................     12/23/80  45 FR 84769............  (c)11..................  EPA conditionally
                                                                                                                                        approved changes
                                                                                                                                        to meet federal
                                                                                                                                        New Source
                                                                                                                                        Review (NSR)
                                                                                                                                        requirements. CT
                                                                                                                                        did not submit
                                                                                                                                        Prevention of
                                                                                                                                        Significant
                                                                                                                                        Determination
                                                                                                                                        program.
                                            8/31/79...................      1/07/82  47 FR 762..............  (c) 20.................  Final approval of
                                                                                                                                        NSR Rules
                                                                                                                                        removing
                                                                                                                                        conditions of 12/
                                                                                                                                        23/80.

[[Page 242]]

                                            10/10/80..................      1/07/82  47 FR 762..............  (c) 20.................  Allows
                                                                                                                                        conditional
                                                                                                                                        exemption of
                                                                                                                                        resource
                                                                                                                                        recovery
                                                                                                                                        facilities from
                                                                                                                                        offset
                                                                                                                                        transactions.
                                            10/10/80..................      1/07/82  47 FR 762..............  (c) 20.................  Replaces the word
                                                                                                                                        ``actual'' with
                                                                                                                                        word
                                                                                                                                        ``allowable''.
                                            12/27/88..................      2/23/93  58 FR 10957............  (c) 56.................  Changes to NSR
                                                                                                                                        and PSD
                                                                                                                                        requirements.
22a-174-4..............  Source             4/04/72...................      5/31/72  37 FR 23085............  (b).                     .................
                          monitoring,
                          record keeping,
                          reporting and
                          authorization of
                          inspection of
                          air pollution
                          sources.
                                            10/31/77..................     12/23/80  45 FR 84769............  (c) 11.................  Clarifies record
                                                                                                                                        keeping and
                                                                                                                                        reporting
                                                                                                                                        requirements and
                                                                                                                                        rescinds smoke
                                                                                                                                        monitoring
                                                                                                                                        requirements for
                                                                                                                                        small sources.
                                            12/15/80..................      8/24/82  47 FR 36822............  (c) 20.................  Rescinded
                                                                                                                                        requirements for
                                                                                                                                        smoke monitors
                                                                                                                                        on sources less
                                                                                                                                        than 250 mmBtu.
                                            12/27/88..................      2/23/93  58 FR 10957............  (c) 56.................  Changes to
                                                                                                                                        opacity
                                                                                                                                        continuous
                                                                                                                                        emission
                                                                                                                                        monitoring (CEM)
                                                                                                                                        requirements.
22a-174-5..............  Methods for        4/04/72...................      5/31/72  37 FR 23085............  (b).                     .................
                          sampling,
                          emission
                          testing, and
                          reporting.
                                            10/05/77..................     12/23/80  45 FR 84769............  (c) 11.................  Tied State
                                                                                                                                        testing method
                                                                                                                                        requirement to
                                                                                                                                        federal
                                                                                                                                        requirements,
                                                                                                                                        clarified
                                                                                                                                        requirements for
                                                                                                                                        stack testing,
                                                                                                                                        and eliminated
                                                                                                                                        record keeping
                                                                                                                                        and reporting
                                                                                                                                        requirements.
                                            12/19/80..................      8/28/81  46 FR 43418............  (c) 16.................  Revisions to
                                                                                                                                        source
                                                                                                                                        monitoring and
                                                                                                                                        stack testing
                                                                                                                                        requirements for
                                                                                                                                        SO2.
22a-174-6..............  Air Pollution      4/04/72...................      5/31/72  37 FR 23085............  (b).                     .................
                          Emergency
                          Episode
                          Procedures.
                                            8/31/79...................     12/23/80  45 FR 84769............  (c) 11.................  Allows DEP to
                                                                                                                                        separately limit
                                                                                                                                        mobile and
                                                                                                                                        stationary
                                                                                                                                        sources
                                                                                                                                        depending upon
                                                                                                                                        the cause of the
                                                                                                                                        episode.
22a-174-7..............  Malfunction of     4/04/72...................      5/31/72  37 FR 23085............  (b).                     .................
                          Control
                          Equipment;
                          Reporting.
22a-174-8..............  Compliance Plans   4/04/72...................      5/31/72  37 FR 23085............  (b).                     .................
                          and Schedules.

[[Page 243]]

22a-174-9..............  Prohibition of     4/04/72...................      5/31/72  37 FR 23085............  (b).                     .................
                          air pollution.
                                            8/31/79...................     12/23/80  45 FR 84769............  (c) 11.................  Non-substantive
                                                                                                                                        numbering
                                                                                                                                        change.
                                            8/31/79...................      8/12/83  48 FR 36579............  (c) 11.................  Full authority
                                                                                                                                        delegated for
                                                                                                                                        NSPS and
                                                                                                                                        NESHAPS.
                                                                            12/6/91  56 FR 63875............                           Delegation of new
                                                                                                                                        subparts.
22a-174-10.............  Public             4/04/72...................      5/31/72  37 FR 23085............  (b).                     .................
                          Availability of
                          Information.
22a-174-11.............  Prohibition        4/04/72...................      5/31/72  37 FR 23085............  (b).                     .................
                          against
                          concealment of
                          circumvention.
22a-174-12.............  Violations and     4/4/72....................      5/31/72  37 FR 23085............  (b).
                          enforcement.
22a-174-13.............  Variances........  4/4/72....................      5/31/72  37 FR 23085............  (b).
                                            8/31/79...................     12/23/80  45 FR 84769............  (c) 11.................  Non-substantive
                                                                                                                                        numbering
                                                                                                                                        change.
22a-174-14.............  Compliance with    4/04/72...................      5/31/72  37 FR 10842............  (b).
                          regulation no
                          defense to
                          nuisance claim.
22a-174-15.............  Severability.....  4/4/72....................      5/31/72  37 FR 10842............  (b).
22a-174-16.............  Responsibility to  4/4/72....................      5/31/72  37 FR 10842............  (b).
                          comply with
                          applicable
                          regulations.
22a-174-17.............  Control of open    4/04/72...................      5/31/72  37 FR 10842............  (b).
                          burning.
22a-174-18.............  Control of         4/4/72....................      5/31/72  37 FR 10842............  (b).
                          particulate
                          emissions.
                                            11/30/73..................      4/16/74  39 FR 13651............  52.375.................  Allowed Hartford
                                                                                                                                        Electric Light &
                                                                                                                                        Connecticut
                                                                                                                                        Light & Power
                                                                                                                                        Supplies to use
                                                                                                                                        nonconforming
                                                                                                                                        fuel from 12/3/
                                                                                                                                        73 to 1/1/74.
                                            7/11/81...................      9/23/82  47 FR 41958............  (c) 22.................  Defines TSP RACT
                                                                                                                                        for fuel burning
                                                                                                                                        equipment and
                                                                                                                                        process sources
                                                                                                                                        including
                                                                                                                                        cupolas,
                                                                                                                                        foundries, and
                                                                                                                                        hot mix asphalt
                                                                                                                                        plants.
22a-174-19.............  Control of sulfur  4/4/72....................      5/31/72  37 FR 23085............  (b).
                          compound
                          emissions.
                                            11/30/73..................      4/16/74  39 FR 13651............  52.375.................  Allowed Hartford
                                                                                                                                        Electric Light
                                                                                                                                        and Connecticut
                                                                                                                                        Power and Light
                                                                                                                                        to use
                                                                                                                                        nonconforming
                                                                                                                                        fuel.
                                            4/3/79....................      7/30/79  44 FR 44498............  (c) 10.................  Allowed Northeast
                                                                                                                                        Utilities to
                                                                                                                                        purchase, store,
                                                                                                                                        and burn
                                                                                                                                        nonconforming
                                                                                                                                        fuel.
                                            9/8/80....................      4/27/81  46 FR 23412............  (c) 12.................  Variance for
                                                                                                                                        Federal
                                                                                                                                        Paperboard, Inc.
                                            12/19/80 & 3/11/81........      8/28/81  46 FR 43418............  (c) 14.................  Amends sulfur
                                                                                                                                        control
                                                                                                                                        strategy.
                                            3/11/81 & 7/15/81.........      8/28/81  46 FR 43418............  (c) 15.................  Amends New Source
                                                                                                                                        Ambient Impact
                                                                                                                                        Analysis
                                                                                                                                        Guideline.
                                            3/17/81...................     10/23/81  46 FR 51914............  (c) 17.................  Variance for
                                                                                                                                        Uniroyal, Inc.
                                            11/2/81...................     11/18/81  46 FR 56612............  (c) 18.................  Approval State
                                                                                                                                        Energy Trade
                                                                                                                                        program.

[[Page 244]]

                                            11/14/75..................     11/18/81  46 FR 56612............  52.380 (e)(1)..........  EPA disapproval
                                                                                                                                        revision which
                                                                                                                                        allows exemption
                                                                                                                                        for home heating
                                                                                                                                        with coal,
                                                                                                                                        historic
                                                                                                                                        demonstrations,
                                                                                                                                        and other small
                                                                                                                                        sources.
                                            11/12/81..................     12/22/81  46 FR 62062............  (c) 19.................  Variances for
                                                                                                                                        United
                                                                                                                                        Technologies
                                                                                                                                        Corp., Pratt &
                                                                                                                                        Whitney Aircraft
                                                                                                                                        Division
                                                                                                                                        facilities in
                                                                                                                                        New Haven and
                                                                                                                                        Middletown.
                                            7/7/81....................     11/12/82  47 FR 51129............  (c) 24.................  Variance for
                                                                                                                                        Sikorsky
                                                                                                                                        Aircraft--approv
                                                                                                                                        ed under the
                                                                                                                                        State Energy
                                                                                                                                        Trade Program.
                                            5/27/82...................       2/8/83  48 FR 5723.............  (c) 26.................  Variance for Dow
                                                                                                                                        Chemical--approv
                                                                                                                                        ed under the
                                                                                                                                        State Energy
                                                                                                                                        Trade Program.
                                            12/15/82..................       5/4/83  48 FR 20051............  (c) 27.................  Variance for
                                                                                                                                        Lydall, Inc.--
                                                                                                                                        approved under
                                                                                                                                        the State Energy
                                                                                                                                        trade (SET)
                                                                                                                                        Program.
                                            11/1/82...................      6/28/83  48 FR 29689............  (c) 28.................  Simkins
                                                                                                                                        Industries--appr
                                                                                                                                        oved under the
                                                                                                                                        State Energy
                                                                                                                                        Trade Program.
                                            3/28/83...................     12/20/83  48 FR 56218............  (c) 30.................  Variance for
                                                                                                                                        Loomis
                                                                                                                                        Institute--appro
                                                                                                                                        ved under the
                                                                                                                                        State Energy
                                                                                                                                        Trade Program.
                                            2/19/93...................      1/18/94  59 FR 2531.............  (c) 63.................  Changes
                                                                                                                                        requirements at
                                                                                                                                        Himilton
                                                                                                                                        Standard
                                                                                                                                        Division of UTC.
22a-174-20.............  Control of         4/4/72....................      5/31/72  37 FR 23085............  (b).
                          organic compound
                          emissions.
                                            8/31/79...................     12/23/80  45 FR 84769............  (c) 11.................  Requirements for
                                                                                                                                        certain Group I
                                                                                                                                        CTG source
                                                                                                                                        categories.
                                                                                                                                        Conditionally
                                                                                                                                        approved cutback
                                                                                                                                        asphalt and
                                                                                                                                        solvent metal
                                                                                                                                        cleaning
                                                                                                                                        categories.
                                            10/10/80..................      1/17/82  47 FR 762..............  (c) 20.................  Requirements for
                                                                                                                                        cutback asphalt
                                                                                                                                        (Group I--CTG).
                                            10/10/80..................      2/17/82  47 FR 6827.............  (c) 25.................  Requirements for
                                                                                                                                        Group II CTGs
                                                                                                                                        exclusive of
                                                                                                                                        controlling
                                                                                                                                        gasoline tank
                                                                                                                                        truck leaks,
                                                                                                                                        petroleum liquid
                                                                                                                                        storage external
                                                                                                                                        floating roof
                                                                                                                                        tanks,
                                                                                                                                        manufacture of
                                                                                                                                        vegetable oil,
                                                                                                                                        pneumatic rubber
                                                                                                                                        tire categories.
                                                                                                                                        Other VOC rules.
                                            10/10/80..................       6/7/82  47 FR 24452............  (c) 23.................  Alternative
                                                                                                                                        emission
                                                                                                                                        reduction
                                                                                                                                        provisions.

[[Page 245]]

                                            12/10/82..................       2/1/84  49 FR 3989.............  (c) 29.................  Requirements for
                                                                                                                                        small open top
                                                                                                                                        degreasers
                                                                                                                                        (Group I--CTG).
                                            9/24/83...................       2/1/84  49 FR 3989.............  (c) 29.................  Exempts colds
                                                                                                                                        cleaners at auto
                                                                                                                                        repair
                                                                                                                                        facilities.
                                            9/24/83...................      3/21/84  49 FR 10542............  (c) 32.................  Adds degreasing
                                                                                                                                        requirements for
                                                                                                                                        conveyorized and
                                                                                                                                        cold cleaning
                                                                                                                                        operations.
                                            8/31/79...................      3/21/84  49 FR 10542............  (c) 32.................  Requirements for
                                                                                                                                        solvent metal
                                                                                                                                        cleaning (Group
                                                                                                                                        I CTG).
                                            9/24/83...................      3/21/84  49 FR 10542............  (c) 32.................  Exempts storage
                                                                                                                                        vessels from
                                                                                                                                        submerged fill.
                                                                                                                                        Delays effective
                                                                                                                                        date of Stage I
                                                                                                                                        vapor recovery
                                                                                                                                        by 1 year.
                                                                                                                                        Requires RACT
                                                                                                                                        for all major
                                                                                                                                        sources of VOC
                                                                                                                                        not covered
                                                                                                                                        under a CTG
                                                                                                                                        document.
                                            9/24/83...................     10/19/84  49 FR 41026............  (c) 33.................  Adds major non-
                                                                                                                                        ctg sources
                                                                                                                                        covered by
                                                                                                                                        20(ee) to
                                                                                                                                        applicability,
                                                                                                                                        compliance,
                                                                                                                                        alternative
                                                                                                                                        emission
                                                                                                                                        reduction and
                                                                                                                                        seasonal
                                                                                                                                        operation after
                                                                                                                                        burner
                                                                                                                                        provisions.
                                            12/13/84..................      7/18/85  50 FR 29229............  (c) 34.................  Revision to
                                                                                                                                        cutback asphalt
                                                                                                                                        regulation.
                                                                                                                                        Requires
                                                                                                                                        facilities with
                                                                                                                                        external
                                                                                                                                        floating roofs
                                                                                                                                        to install
                                                                                                                                        secondary seats.
                                                                                                                                        Changes to
                                                                                                                                        gasoline tank
                                                                                                                                        truck
                                                                                                                                        regulation.
                                            4/23/86...................     11/20/86  51 FR 41963............  (c) 36.................  VOC RACT for
                                                                                                                                        Connecticut
                                                                                                                                        Charcoal
                                                                                                                                        Company.
                                            4/28/86...................      2/19/87  52 FR 5104.............  (c) 37.................  VOC RACT for King
                                                                                                                                        Industries.
                                            8/8/87....................     12/17/87  52 FR 47925............  (c) 39.................  VOC RACT for
                                                                                                                                        Belding
                                                                                                                                        Corticelli
                                                                                                                                        Thread Company.
                                            5/28/86...................      2/17/88  51 FR 4621.............  (c) 41.................  Effective date
                                                                                                                                        clarification
                                                                                                                                        for Connecticut
                                                                                                                                        Charcoal.
                                            9/24/87...................      4/11/88  53 FR 11847............  (c) 42.................  VOC RACT for
                                                                                                                                        Raymark
                                                                                                                                        Industries, Inc.
                                            2/2/87....................      5/19/88  53 FR 17934............  (c) 38.................  Clarifies
                                                                                                                                        applicability of
                                                                                                                                        VOC compliance
                                                                                                                                        methods for
                                                                                                                                        surface coating
                                                                                                                                        sources.
                                            3/17/87...................      5/19/88  53 FR 17934............  (c) 38.................  Adds regulations
                                                                                                                                        for SOCMI
                                                                                                                                        fugitive leaks
                                                                                                                                        and polystyrene
                                                                                                                                        resins.
                                            8/21/87...................      7/12/88  53 FR 26256............  (c) 44.................  VOC RACT for
                                                                                                                                        Spongex
                                                                                                                                        International
                                                                                                                                        Ltd.
                                            12/26/86..................       8/1/88  53 FR 28884............  (c) 43.................  VOC RACT for
                                                                                                                                        American
                                                                                                                                        Cyanamid
                                                                                                                                        Company.
                                            10/27/88..................       3/8/89  54 FR 9781.............  (c) 48.................  VOC RACT for Dow
                                                                                                                                        Chemical, U.S.A.
                                            6/7/88....................      3/24/89  54 FR 12193............  (c) 46.................  VOC RACT for New
                                                                                                                                        Departure Hyatt.
                                            12/14/88..................      4/10/89  54 FR 14226............  (c) 49.................  VOC RACT for
                                                                                                                                        Stanadyne.
                                            3/22/89...................      5/30/89  54 FR 22891............  (c) 51.................  VOC RACT for
                                                                                                                                        Pratt & Whitney
                                                                                                                                        Division of UTC.

[[Page 246]]

                                            12/30/88..................       6/2/89  54 FR 23650............  (c) 50.................  Changes limit on
                                                                                                                                        volatility of
                                                                                                                                        gasoline.
                                            10/19/87..................     11/28/89  54 FR 48885............  (c) 47.................  VOC RACT for
                                                                                                                                        Frismar, Inc.
                                            10/18/88..................     11/39/89  54 FR 49284............  (c) 52.................  VOC RACT for
                                                                                                                                        Pfizer, Inc.
                                            9/5/89....................     12/22/89  54 FR 52798............  (c) 53.................  VOC RACT for
                                                                                                                                        Uniroyal
                                                                                                                                        Chemical Co.
                                            11/29/89..................      3/12/90  55 FR 9121.............  (c) 54.................  VOC RACT for
                                                                                                                                        Hamilton
                                                                                                                                        Standard
                                                                                                                                        Division of
                                                                                                                                        United
                                                                                                                                        Technologies
                                                                                                                                        Corp.
                                            11/2/88...................      3/14/90  55 FR 9442.............  (c) 55.................  VOC RACT for
                                                                                                                                        Heminway &
                                                                                                                                        Bartlett
                                                                                                                                        Manufacturing
                                                                                                                                        Company.
                                            10/31/89..................     10/18/91  56 FR 52205............  (c) 58.................  Changes
                                                                                                                                        applicability to
                                                                                                                                        facilities with
                                                                                                                                        >=15 pounds VOC
                                                                                                                                        per day.
                                            10/31/89..................     10/18/91  56 FR 52205............  (c) 58.................  Various changes
                                                                                                                                        to Section 20
                                                                                                                                        approved.
                                            9/1/93....................     11/19/93  58 FR 61041............  .......................  Withdrawal of NPR
                                                                                                                                        for Sikorsky
                                                                                                                                        Aircraft
                                                                                                                                        Division of UTC,
                                                                                                                                        Bridgeport.
                                            1/29/90, 9/29/95, & 2/7/96       2/9/98  63 FR 6484.............  (c) (60)...............  VOC RACT for
                                                                                                                                        Sikorsky
                                                                                                                                        Aircraft
                                                                                                                                        Corporation in
                                                                                                                                        Stratford.
                                            6/3/96....................      4/24/98  63 FR 20318............  (c) (73)...............  Alternative VOC
                                                                                                                                        RACT for Risdon
                                                                                                                                        Corporation in
                                                                                                                                        Danbury.
22a-174-21.............  Control of carbon  4/4/72....................      5/31/72  37 FR 23085............  (b).
                          monoxide
                          emissions.
                                            9/21/82...................      3/21/84  49 FR 10542............  (c) 32.................  CO attainment
                                                                                                                                        plan.
22a-174-22.............  Control of         4/472.....................      5/31/72  37 FR 23085............  (b).
                          nitrogen oxide
                          emissions.
                                            8/31/79...................     12/23/80  49 FR 84769............  (c) 11.................  Exemption of fast
                                                                                                                                        response double
                                                                                                                                        furnace naval
                                                                                                                                        burners and
                                                                                                                                        cyclone furnaces
                                                                                                                                        (not addressed
                                                                                                                                        by EPA).
                                            5/18/95...................      10/6/97    .....................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for United
                                                                                                                                        Illuminating's
                                                                                                                                        Station #3, in
                                                                                                                                        Bridgeport.
                                            6/2/95....................      10/6/97    .....................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for American Ref-
                                                                                                                                        Fuel of
                                                                                                                                        Southeastern
                                                                                                                                        Connecticut in
                                                                                                                                        Preston.
                                            7/19/95...................      10/6/97    .....................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for Pfizer, Inc.
                                                                                                                                        in Groton.
                                            8/25/95...................      10/6/97    .....................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for Food
                                                                                                                                        Ingredients
                                                                                                                                        Specialties,
                                                                                                                                        Inc. in New
                                                                                                                                        Milford.

[[Page 247]]

                                            10/10/95..................      10/6/97    .....................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for Connecticut
                                                                                                                                        Light and Power
                                                                                                                                        in Middletown.
                                            10/13/95..................      10/6/97    .....................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for Northeast
                                                                                                                                        Nuclear Energy
                                                                                                                                        Co. in
                                                                                                                                        Waterford.
                                            10/31/95..................      10/6/97    .....................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for Electric
                                                                                                                                        Boat Division of
                                                                                                                                        General Dynamics
                                                                                                                                        in Groton.
                                            11/2/95...................      10/6/97    .....................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for Bridgeport
                                                                                                                                        RESCO Co. in
                                                                                                                                        Bridgeport.
                                            12/15/95..................      10/6/97    .....................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for United
                                                                                                                                        Illuminating's
                                                                                                                                        auxiliary
                                                                                                                                        boiler, in New
                                                                                                                                        Haven.
                                            2/14/96...................      10/6/97    .....................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for United
                                                                                                                                        Illuminating's
                                                                                                                                        Station #4, in
                                                                                                                                        Bridgeport.
                                            3/4/96....................      10/6/97    .....................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for Norwich
                                                                                                                                        Department of
                                                                                                                                        Public
                                                                                                                                        utilities.
                                            3/19/96...................      10/6/97  .......................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for South
                                                                                                                                        Norwalk Electric
                                                                                                                                        Works.
                                            7/16/96...................      10/6/97  .......................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for the
                                                                                                                                        Connecticut
                                                                                                                                        Dept. of Mental
                                                                                                                                        Health and
                                                                                                                                        Addiction
                                                                                                                                        Services.
                                            7/29/96...................      10/6/97  .......................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for Yale
                                                                                                                                        University.
                                            9/10/96...................      10/6/97  .......................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for Bridgeport
                                                                                                                                        Hospital.
                                            10/15/96..................      10/6/97  .......................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for Connecticut
                                                                                                                                        Light & Power's
                                                                                                                                        Branford, Cos
                                                                                                                                        Cob, Devon,
                                                                                                                                        Franklin Drive,
                                                                                                                                        Montville,
                                                                                                                                        Middletown,
                                                                                                                                        South Meadow,
                                                                                                                                        Torrington,
                                                                                                                                        Tunnel Road, and
                                                                                                                                        Norwalf Harbor
                                                                                                                                        stations.
                                            10/18/96..................      10/6/97  .......................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for the
                                                                                                                                        Connecticut
                                                                                                                                        Department of
                                                                                                                                        Public Works.
                                            11/19/96..................      10/6/97  .......................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for University
                                                                                                                                        of Connecticut
                                                                                                                                        in Storrs.
                                            11/19/96..................      10/6/97  .......................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for Simkins
                                                                                                                                        Industries.
                                            12/24/96..................      10/6/97  .......................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for Bridgeport
                                                                                                                                        Hydraulic
                                                                                                                                        Company.
                                            12/27/96..................      10/6/97  .......................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for the Town of
                                                                                                                                        Wallingford
                                                                                                                                        Dept. of Public
                                                                                                                                        Utilities.
                                            1/23/97...................      10/6/97  .......................  (c) 72.................  Establishes NOX
                                                                                                                                        RACT regulations
                                                                                                                                        and source-
                                                                                                                                        specific
                                                                                                                                        requirements.

[[Page 248]]

                                            4/18/97...................      10/6/97  .......................  (c) 72.................  Case-Specific
                                                                                                                                        trading order
                                                                                                                                        for Algonquin
                                                                                                                                        Gas Transmission
                                                                                                                                        Company.
                                            4/22/97...................      10/6/97  .......................  (c) 72.................  Case-specific
                                                                                                                                        trading order
                                                                                                                                        for the
                                                                                                                                        Connecticut
                                                                                                                                        Resource
                                                                                                                                        Recovery
                                                                                                                                        Authority.
22a-174-23.............  Control of Odors.  4/4/72....................      5/31/72  37 FR 23085............  (b).
                         Rescinded from     8/31/79...................     12/23/80  45 FR 84769............  (c) 11.................  EPA has no
                          Federal SIP.                                                                                                  authority to
                                                                                                                                        control odors.
22a-174-24.............  Connecticut        4/4/72....................      5/31/72  37 FR 23085............  (b).
                          primary and
                          secondary
                          standards.
                                            7/11/81...................     11/18/81  46 FR 56612............  (c) 18.................  Eliminated State
                                                                                                                                        24-hour and
                                                                                                                                        annual standard
                                                                                                                                        for SO2.
                                            10/8/80...................      2/17/82  47 FR 6827.............  (c) 25.................  Adopted ambient
                                                                                                                                        air quality
                                                                                                                                        standards for
                                                                                                                                        lead and revised
                                                                                                                                        the ozone
                                                                                                                                        standard.
                                            10/8/80...................      8/24/82  47 FR 36822............  (c) 20.................  EPA took ``no
                                                                                                                                        action'' on
                                                                                                                                        definition of
                                                                                                                                        the term
                                                                                                                                        ``acceptable
                                                                                                                                        method'' because
                                                                                                                                        did not ensure
                                                                                                                                        consistency with
                                                                                                                                        EPA monitoring
                                                                                                                                        regulations.
                                            10/8/80...................      11/2/82  47 FR 49646............  (c) 20.................  Correction to
                                                                                                                                        subparagraph
                                                                                                                                        designation.
                                            10/8/80...................     12/13/85  50 FR 50906............  (c) 35.................  Approved
                                                                                                                                        definition of
                                                                                                                                        acceptable
                                                                                                                                        method.
                                            2/25/91...................      3/24/92  57 FR 10139............  (c) 61.................  Requires use of
                                                                                                                                        low sulfur fuels
                                                                                                                                        at Connecticut
                                                                                                                                        Light & Power in
                                                                                                                                        Montville.
                                            2/14/92...................     11/20/92  57 FR 54703............  (c) 59.................  Requires use of
                                                                                                                                        low sulfur fuels
                                                                                                                                        at Stones CT
                                                                                                                                        Paperboard Corp.
                                            2/5/92....................     11/20/92  57 FR 54703............  (c) 59.................  Requires use of
                                                                                                                                        low sulfur fuel
                                                                                                                                        at Hartford
                                                                                                                                        Hospital.
22a-174-25.............  Effective date...  4/4/72....................      5/31/72  37 FR 23085............  (b).
22a-174-27.............  Emission           9/24/82...................      3/21/84  49 FR 10542............  (c) 32.................  Exhaust
                          Standards for                                                                                                 ``emission
                          Motor Vehicles.                                                                                               standards'' for
                                                                                                                                        periodic motor
                                                                                                                                        vehicle
                                                                                                                                        inspection and
                                                                                                                                        maintenance.
14-164C................  Periodic Motor     7/27/82...................      3/21/84  49 FR 10542............  (c) 32.................  Department of
                          Vehicle                                                                                                       Motor Vehicle
                          Emissions                                                                                                     Regulations
                          Inspection and                                                                                                establishing
                          Maintenance.                                                                                                  specifications
                                                                                                                                        for Connecticut
                                                                                                                                        I&M program.
22a-174-30.............  Gasoline Vapor     1/12/93...................     12/17/93  58 FR 65930............  (c) 62.................  Requires Stage II
                          Recovery.                                                                                                     vapor recovery
                                                                                                                                        from gasoline
                                                                                                                                        dispensers.
                                                                            1/18/94  59 FR 2649.............  (c) 62.................  Correction to 12/
                                                                                                                                        17/93 notice.

[[Page 249]]

22a-174-100............  Permits for        1/9/74....................      2/25/74  39 FR 7280.............  (c) 4..................  Requires review
                          construction of                                                                                               of air impacts
                          indirect sources                                                                                              of indirect
                          Rescinded from                                                                                                sources.
                          federal SIP.
                                            8/20/74...................      2/13/76  41 FR 6765.............  (c) 6..................  Added indirect
                                                                                                                                        source review
                                                                                                                                        (ISR)
                                                                                                                                        regulations.
                                            6/30/77...................      1/26/79  44 FR 5427.............  (c) 9.
                                            NA........................     12/23/79  45 FR 84769............  (c) 11.................  SIP shown to
                                                                                                                                        attain standards
                                                                                                                                        as expeditiously
                                                                                                                                        as practicable
                                                                                                                                        without ISR
                                                                                                                                        regulation.
--------------------------------------------------------------------------------------------------------------------------------------------------------

[62 FR 52022, Oct. 6, 1997; 62 FR 65224, Dec. 11, 1997, as amended at 63 
FR 6487, Feb. 9, 1998; 63 FR 20318, Apr. 24, 1998]

[[Page 250]]



                           Subpart I--Delaware



Sec. 52.420  Identification of plan.

    (a) Title of plan: ``State of Delaware Implementation Plans for 
Attainment and Maintenance of National Ambient Air Quality Standards.''
    (b) The plan was officially submitted on January 28, 1972.
    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) Certification that public hearing was held on plan submitted on 
February 11, 1972, by the Department of Natural Resources and 
Environmental Control.
    (2) Information on the geometric standard deviations of air quality 
data submitted on March 7, 1972, by the Department of Natural Resources 
and Environmental Control.
    (3) Miscellaneous non-regulatory clarifications and amendments to 
the plan submitted on May 5, 1972, by the Department of Natural 
Resources and Environmental Control.
    (4) Specification of attainment dates submitted on June 2, 1972, by 
the Department of Natural Resources and Environmental Control.
    (5) Periodic stack sampling requirements submitted on June 5, 1972, 
by the Department of Natural Resources and Environmental Control.
    (6) Miscellaneous non-regulatory additions to the plan submitted on 
July 20, 1972, by the Delaware Water and Air Resource Commission.
    (7) Backup information for the attainment of the Secondary SO2 
standards in New Castle County submitted on November 14, 1972, by the 
Department of Natural Resources and Environmental Control.
    (8) Backup information for the attainment of the Secondary SO2 
standards in New Castle County submitted on December 19, 1972, by the 
Department of Natural Resources and Environmental Control.
    (9) Amendments to Regulations I through XIV inclusive of the 
Delaware Regulations Governing Air Pollution, and Amendments to the 
Delaware Environmental Protection Act; submitted on January 16, 1975 by 
the Delaware Department of Natural Resources and Environmental Control.
    (10) Amendments to Section V (Surveillance) of the Delaware State 
Implementation Plan and amendments to Section V (Surveillance) of the 
New Castle County Portion of the Delaware State Implementation Plan, 
covering changes to the air pollution monitoring system; submitted on 
September 3, 1975 by the Delaware Department of Natural Resources and 
Environmental Control.
    (11) A Consent Order for the Getty Oil Company and the Delmarva 
Power and Light Company submitted on August 5, 1975 by the Delaware 
Department of Natural Resources and Environmental Control.
    (12) Amendments to Regulations No. V, XIV, XVII, and a newly adopted 
Regulation No. XXIII (Standards of Performance for Steel Plants: 
Electric Arc Furnaces); and a Court of Chancery injunction to control 
charging and tapping emissions for the Phoenix Steel Corporation's plant 
in Claymont, Delaware submitted on December 2, 1977 and October 5, 1978, 
respectively, by the Department of Natural Resources and Environmental 
Control.
    (13) On May 3, 1979, the Governor submitted the nonattainment area 
plan for New Castle County with respect to ozone.
    (14) A revision submitted by the State of Delaware on October 5, 
1978 to eliminate certain outdated requirements relating to Regulations 
V and XVIII and correction of typographical errors relating to 
Regulations III, VIII, and XV.
    (15) A revision submitted by the State of Delaware on March 19, 1980 
which is intended to establish an Ambient Air Quality Monitoring 
Network.
    (16) Revisions to Delaware's Regulations I, II, III, IV, VIII, XII, 
XIV, XV, and XVII submitted by the Delaware Department of Natural 
Resources and Environmental Control on March 19, 1980.
    (17) A revision submitted by the State of Delaware on September 7, 
1977, consisting of an amendment to Delaware Regulations Governing Air 
Pollution, Regulation XVII, establishing continuous emission monitoring 
regulations.
    (18) A revision submitted by the District of Columbia on May 16, 
1979 which

[[Page 251]]

is intended to establish an Ambient Air Quality Monitoring Network.
    (19) A commitment to use available grants and funds to establish, 
expand, and improve public transportation to meet basic transportation 
needs, submitted on August 15, 1979 by the Delaware Transportation 
Authority.
    (20) A revised schedule for implementation of Delaware's inspection 
and maintenance program submitted by September 10, 1980 by the 
Secretary, Delaware Department of Natural Resources and Environmental 
Control.
    (21) [Reserved]
    (22) A revision submitted by the State of Delaware on August 7, 1978 
consisting of two Executive Orders for financial disclosure of certain 
State officials.
    (23) Amendments to Regulations I (Definitions) and XXIV (Control of 
Organic Compounds Emissions) submitted on December 23, 1980 by the 
Secretary, Delaware Department of Natural Resources and Environmental 
Control.
    (24) A State Implementation Plan for the Control of lead emissions 
submitted on December 23, 1980 by the Secretary, Delaware Department of 
Natural Resources and Environmental Control.
    (25) A revised schedule for implementation of Delaware's inspection 
and maintenance program submitted on December 29, 1980 by the Secretary, 
Delaware Department of Natural Resources and Environmental Control.
    (26) Amendments to Regulation II (Registration and Permits) and XIII 
(Open Burning) [non-regulatory] of the Delaware Regulations governing 
the Control of Air Pollution submitted on September 22, 1981 by the 
Secretary, Department of Natural Resources and Environmental Control.
    (27) Amendments to Section 9.4 (Surface Coating operations) and 13.2 
(Dry Cleaning) of Regulation XXIV (Control of Volatile Organic Compound 
Emissions) of the Delaware Regulations governing the Control of Air 
Pollution submitted on September 22, 1981 by the Secretary, Department 
of Natural Resources and Environmental Control.
    (28) Amendments to Regulations I (Definitions) and XXV Section 
(Requirements for Preconstruction Review) pertaining to prevention of 
significant deterioration submitted on December 29, 1980 by the 
Secretary, Delaware Department of Natural Resources and Environmental 
Control.
    (29) A February 27, 1981 letter from the Delaware Department of 
Natural Resources and Environmental Control to EPA pertaining to 
procedures of notifying EPA of any PSD application for sources locating 
within 100 kilometers of a Class I PSD area, as well as ensuring EPA in 
any monitoring procedure, that the requirements of 40 CFR part 58 will 
be specified.
    (30) A revision submitted by the State of Delaware on October 14, 
1982, consisting of amendments to Regulation No. II--Permits.
    (31) Plan Revision providing for attainment of the Ozone standard 
submitted by John E. Wilson, III to EPA on July 6, 1982.
    (32) Stack height regulation, public notification plan, and other 
miscellaneous revisions submitted to EPA on April 20, 1983.
    (33) A revision submitted by the State of Delaware on September 26, 
1983 consisting of amendments to Section 2.3 of Regulation Number XIV, 
Section 2.3 of Regulation Number VII, and Section 9.7 and Table I(a) to 
Regulation Number XXIV of the DelawareRegulations Governing the Control 
of Air Pollution.
    (34) Revisions to the Delaware Regulations Governing the Control of 
Air Pollution were submitted by the Secretary on August 8, 1984.
    (i) Incorporation by reference. (A) Amendments to Regulations II 
(Permits); XIII (Open Burning); XIV (Visible Emissions); and XVII 
(Source Monitoring, Record Keeping and Reporting).
    (35) Revisions submitted by the State of Delaware on June 5, 1985 
amending the State of Delaware Regulations Governing the Control of Air 
Pollution, Regulation Nos. VIII, XIII, and XXVI.
    (i) Incorporation by reference. (A) Revisions via Order No. 85-A-3 
Exhibit A Amendment Nos. 2, 3, and 5, to the State of Delaware 
Regulations Governing the Control of Air Pollution, Regulations VIII 
sections 2.1-2.4, XIII section 1.2, and XXVI Table 2, pertaining to 
sulfur in fuel oil, open burning, and

[[Page 252]]

motor vehicle emission testing, respectively. These revisions were 
adopted by the Department of Natural Resources and Environmental Control 
on May 9, 1985.
    (ii) Additional information. (A) A letter dated July 9, 1985 from 
Secretary John E. Wilson, III to Mr. James M. Seif, withdrawing certain 
portions of the original SIP revision request pertaining to asbestos, 
New Source Performance Standards (Regulation No. XX), and Emission 
Standards for Hazardous Air Pollutants (Regulation No. XXI).
    (B) A letter dated July 9, 1986 from Mr. Robert R. French to Mr. 
James Sydnor withdrawing the request to delete the definitions of 
``Reconstruction'' and ``Capital Expenditure'' from their new source 
review regulations (Regulations I and XXV).
    (36) [Reserved]
    (37) Revision submitted by the State of Delaware on March 6, 1987, 
consisting of amendment to Regulation II-Permits.
    (i) Incorporation by reference. State of Delaware Order No. 87-A-2 
(Introduction, Findings of Fad and (1) of the order which amends section 
2.7 of Regulation II) which was issued on February 18, 1987.
    (38) Revision to the Delaware State Implementation Plan 
incorporation of a Conciliatory Order, was submitted on May 31, 1989. 
The order is designed to reduce ambient sulfur dioxide levels around the 
Delmarva Power and Light Company's Indian River power plant.
    (i) Incorporation by reference.
    (A) Letter dated May 31, 1989 from the State of Delaware containing 
the Conciliatory Order for incorporation into the Delaware State 
Implementation Plan.
    (B) Conciliatory Order issued on May 31, 1989, for Delmarva Power 
and Light Company's Indian River power plant.
    (39) Revisions to the State Implementation Plan were submitted by 
the Delaware Department of Natural Resources and Environmental Control 
on March 6, 1987 (Secretary's Order No. 87-A-2). Revisions to the State 
Implementation Plan submitted by the Delaware Department of Natural 
Resources and Environmental Control on March 21, 1988 (Secretary's Order 
No. 89-A-5).
    (i) Incorporation by reference.
    (A) Letter received on March 6, 1987, from the Delaware Department 
of Natural Resources and Environmental Control submitting revisions to 
the State Implementation Plan for EPA approval (portions of Secretary 
Order No. 87-A-2).
    (B) Letter dated December 21, 1988, from the Delaware Department of 
Natural Resources and Environmental Control submitting revisions to the 
State Implementation Plan for EPA approval (portions of Secretary Order 
No. 89-A-5).
    (C) Only those portions of Secretary's Order No. 87-A-2 issued on 
February 18, 1987, which amend Regulation No. II, Stack Heights at 
sections 2.2, 2.3, 2.4, and 2.5, pertaining to the definitions of the 
terms excessive concentrations, nearby stack, and stack in existence; 
and at sections 3.1, 3.2, and 3.3, pertaining to the requirements for 
new and existing sources.
    (D) Only those portions of Secretary's Order No. 89-A-5, issued on 
December 7, 1988, which amend Regulation No. XXV, Requirements for 
Preconstruction Review, at section 3.9(A) and Regulation No. XXVII, 
Stack Heights at section 2 to include definitions of the terms emission 
limitation and emission standard.
    (40)  [Reserved]
    (41) Revision submitted by the State of Delaware on April 28, 1988 
amending the hydrocarbon motor vehicle emission testing standards in 
Regulation XXVI of the Delaware Regulations Governing the Control of Air 
Pollution.
    (i) Incorporation by reference. (A) Revisions via Order 88-A-2, 
exhibit A, parts A and B, which is an amendment to Table 2 of Technical 
Memorandum Number 2 entitled ``Motor Vehicle Inspection and Maintenance 
Program Emission Limit Determination''. This revision was issued by the 
State on December 29, 1987.
    (42) Revisions to the State Implementation Plan submitted by the 
Delaware Department of Natural Resources and Environmental Control on 
December 12, 1985, pertaining to Delaware Regulation No. XXIV which 
includes an alternative RACT standard for the zinc-rich weld-through 
primer coating.
    (i) Incorporation by reference.

[[Page 253]]

    (A) Letter from the Delaware Department of Natural Resources and 
Environmental Control dated December 12, 1985 submitting a revision to 
the Delaware State Implementation Plan, regarding changes to Regulation 
No. XXIV to remove the word ``yearly'' from Tables I and I(a) and to 
propose an alternative RACT standard for the zinc-rich primer coating.
    (B) Those portions of Exhibit 13 of Order No. 85-A-5 amending 
Regulation No. XXIV by 1) deleting the word ``yearly'' in Tables I and 
I(a) and (2) adopting 4.0 as the Reasonably Available Control Technology 
(RACT) emission limit for Zinc-rich Primer used in automobile surface 
coating.
    (ii) Additional materials.
    (A) Remainder of the State submittal.
    (43) Revision to the State Implementation Plan submitted by the 
Delaware Department of Natural Resources and Environmental Control on 
March 6, 1990, amending portions of Regulation XXVI (26) of the Delaware 
Regulations Governing the Control of Air Pollution by expanding the I/M 
program statewide, adopting CO cutpoints statewide, modifying the test 
procedures, and increasing the waiver cost repair limit.
    (i) Incorporation by reference.
    (A) Letter from the Delaware Department of Natural Resources and 
Environmental Control dated March 6, 1990 submitting a revision to the 
Delaware State Implementation Plan.
    (B) Sections 1, 2, 4 and 6 of Regulation XXVI (26), Motor Vehicle 
Emissions Inspection Program, of the Delaware Regulations Governing the 
Control of Air Pollution and the two (2) Technical Memoranda, Numbers 1 
and 2, which are appendices to Regulation XXVI (26), of the Delaware 
Regulations Governing the Control of Air Pollution.
    (ii) Additional materials--remainder of State submittal.
    (44) Revisions to the State Implementation Plan submitted by the 
Delaware Department of Natural Resources and Environmental Control on 
July 6, 1990.
    (i) Incorporation by reference.
    (A) A letter from the Delaware Department of Natural Resources and 
Environmental Control dated July 6, 1990 submitting a revision to the 
Delaware State Implementation Plan, effective July 3, 1990.
    (B) Regulation 1--Definitions and Administrative Principles.
    (C) Regulation 24--Section 1, General Provisions; section 6, Bulk 
Gasoline Plants; section 8, Petroleum Liquid Storage; section 9, Surface 
Coating Operations; section 14, Petroleum Refinery Component Leaks; and 
section 15, Rotogravure and Flexographic Printing.
    (45) Revisions to the State Implementation Plan submitted by the 
Delaware Department of Natural Resources and Environmental Control on 
March 9, 1990.
    (i) Incorporation by reference.
    (A) Letter from the Delaware Department of Natural Resources and 
Environmental Control dated March 6, 1990, submitting a revision to the 
Delaware State Implementation Plan.
    (B) The portion of Secretary Order 90-A-1 that amends Regulation 
II--Permits--Section 3.1.b.1; and Regulation XXV--Requirements for 
Preconstruction Review--Sections 1.9 (N) 1-4, 3.1, and 3.9. The 
amendments to Regulation II and Regulation XXV were adopted on January 
31, 1990, and were effective on May 15, 1990, in the state of Delaware.
    (46) Revisions to the Delaware State Implementation Plan submitted 
on January 11, 1993 by the Delaware Department of Natural Resources & 
Environmental Control:
    (i) Incorporation by reference. (A) Letter of January 11, 1993 from 
the Delaware Department of Natural Resources & Environmental Control 
transmitting Regulation 24--``Control of Volatile Organic Compound 
Emissions'', effective January 11, 1993.
    (B) Regulation 24--``Control of Volatile Organic Compound 
Emissions'', Sections 1, 2, 3, 4, 5, 6, 7, 8, 9, 13, 14, 15, 16, 17, 18, 
19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 37, 
38, 39, 40, 41, 42, and Appendices A, B, C, D, E, F, G, & H.
    (47) Revisions to the Delaware regulations for particulate matter 
(PM-10) submitted on April 26, 1988 by the Delaware Department of 
Natural Resources and Environmental Control:

[[Page 254]]

    (i) Incorporation by reference. (A) Letter of April 26, 1988 from 
the Department of Natural Resources and Environmental Control 
transmitting a revision to the Delaware State implementation plan for 
particulate matter (PM-10) Group III areas.
    (B) Revisions via Order No. 88-A-5, exhibit A, and Table 1. The 
Order amends the following Delaware Regulations Governing the Control of 
Air Pollution: Regulation 1--``Definitions and Administrative 
Principles''; Regulation 3--``Ambient Air Quality Standards''; 
Regulation 15--``Air Pollution Alert and Emergency Plan''; and 
Regulation 25--``Requirements for Preconstruction Review''. The 
revisions were adopted on March 29, 1988 and became effective 
immediately.
    (ii) Additional materials.
    (A) Remainder of the State implementation plan revision submitted by 
the Delaware Department of Natural Resources and Environmental Control 
on April 26, 1988.
    (48) Revisions to the Delaware State Implementation Plan submitted 
on January 20, 1994 by the Delaware Department of Natural Resources & 
Environmental Control:
    (i) Incorporation by reference.
    (A) Letter of January 20, 1994 from the Delaware Department of 
Natural Resources & Environmental Control transmitting Regulation 24--
Control of Volatile Organic Compound Emissions--Sections 50(a)(5) and 
50(b)(3), effective November 24, 1993.
    (B) Regulation 24--Control of Volatile Organic Compound Emissions, 
Section 50--Other Facilities that Emit Volatile Organic Compounds--
Sections 50(a)(5) and 50(b)(3)--Non-CTG RACT, effective November 24, 
1993.
    (ii) Additional material.
    (A) Remainder of January 20, 1994 State submittal pertaining to 
Regulation 24, sections 50(a)(5) and 50(b)(30) referenced in paragraph 
(c)(48)(i) of this section.
    (49) Revisions to the Delaware State Implementation Plan submitted 
on February 17, 1995 by the Delaware Department of Natural Resources & 
Environmental Control:
    (i) Incorporation by reference.
    (A) Letter of February 17, 1995 from the Delaware Department of 
Natural Resources & Environmental Control transmitting Regulation 13--
Open Burning, effective February 8, 1995.
    (B) Regulation 13--Open Burning, effective February 8, 1995.
    (C) Administrative changes to Regulation 1, Definitions and 
Administrative Principles: addition of the following definitions: 
``ceremonial fires'', ``conservation practices'', ``prescribed 
burning'', and ``silviculture''; and revision to the following 
definitions: ``open burning'', ``rubbish'', and ``trade waste'' adopted 
February 8, 1995.
    (ii) Additional material.
    (A) Remainder of the February 17, 1995 State submittal pertaining to 
Regulation 13--Opening Burning referenced in paragraph (c)(49)(i) of 
this section.
    (50) Revisions to the Delaware State Implementation Plan submitted 
on January 11, 1993, by the Delaware Department of Natural Resources & 
Environmental Control:
    (i) Incorporation by reference.
    (A) Letter of January 11, 1993, from the Delaware Department of 
Natural Resources & Environmental Control submitting and requesting 
approval of Stage II Vapor Recovery Regulations for Gasoline Dispensing 
Facilities.
    (B) Addition of Section 36-Stage II Vapor Recovery and Appendix J-
Procedures for Implementation of Regulations Covering Stage II Vapor 
Recovery Systems for Gasoline Dispensing Facilities to Regulation No. 
24, ``Control of Volatile Organic Compound Emissions.'' Section 36 and 
Appendix J have an effective date of January 11, 1993.
    (ii) Additional materials.
    (A) Delaware Secretary's Order No. 93-00078, issued January 11, 
1993, adopting Stage II Vapor Recovery Regulations in the State.
    (B) Remainder of the January 11, 1993, State submittal pertaining to 
Section 36 and Appendix J of Regulation No. 24, Stage II Vapor Recovery 
at Gasoline Dispensing Facilities.
    (51) Revisions to the Delaware State Implementation Plan submitted 
on January 20, 1994 by the Delaware Department of Natural Resources & 
Environmental Control:
    (i) Incorporation by reference. (A) Letter dated January 20, 1994, 
from the Delaware DNREC transmitting an

[[Page 255]]

amendment to Regulation 24, ``Control of Volatile Organic Compound 
Emissions'', Section 43--``Other Facilities that Emit VOCs'', effective 
November 24, 1993.
    (B) Amendment to Regulation 24, ``Control of VOC Emissions'', 
Section 43--``Other Facilities that Emit VOCs'', Sections 43(a)(1), 
43(a)(2), 43(a)(3), 43(a)(4), 43(b)(1), 43(b)(2), 43(c), 43(d), 43(e), 
and 43(f).
    (ii) Additional Material. (A) Remainder of January 11, 1993 and 
January 20, 1994 State submittal pertaining to Regulation 24 referenced 
in paragraphs (c)(46)(i) and (c)(51)(i) of this section.
    (iii) Additional Information. (A) These rules supersede paragraph 
(c)(44)(i)(C) of this section.
    (52) Revisions to the Delaware State Implementation Plan submitted 
by the Secretary, Delaware Department of Natural Resources and 
Environmental Control, on January 11, 1993.
    (i) Incorporation by reference.
    (A) Letter dated January 11, 1993 from the Secretary, Delaware 
Department of Natural Resources and Environmental Control, submitting a 
revision to the Delaware State Implementation Plan.
    (B) Amended section 2, Regulation 1 (Definitions and Administrative 
Principles). Amended section 1, and added new section 7 of Regulation 17 
(Source Monitoring, Recordkeeping and Reporting). The amendments to 
Regulations 1 and 17, and the addition of section 7 of Regulation 17, 
were effective on January 11, 1993. This revision consists of an 
emission statement program for stationary sources which emit volatile 
organic compounds (VOC) and/or nitrogen oxides (NOX) at or 
above specified actual emission threshold levels. This program is 
applicable state-wide.
    (ii) Additional material.
    (A) Remainder of January 11, 1993 state submittal pertaining to 
Delaware Emission Statement Program.
    (53) Revisions to the Delaware Regulations on the control of 
volatile organic compound emissions from marine vessel transfer 
operations submitted on August 26, 1994 by the Delaware Department of 
Natural Resources & Environmental Control:
    (i) Incorporation by reference.
    (A) Letter of August 26, 1994 from the Delaware Department of 
Natural Resources & Environmental Control transmitting Regulation 24, 
``Control of Volatile Organic Compound Emissions'', by renumbering 
existing Section 43, ``Other Facilities that Emit Volatile Organic 
Compounds,'' to Section 50 and adding a new Section 43, ``Bulk Gasoline 
Marine Tank Vessel Loading Facilities''.
    (B) Administrative changes to Section 50: renumbering existing 
Section 43 to Section 50, and Section 50(a)(1): renumbering 42 to 43; 
and the new Section 43, effective August 26, 1994.
    (ii) Additional material.
    (A) Remainder of August 26, 1994 State submittal pertaining to 
Regulation 24 referenced in paragraph (c)(53)(i) of this section.
    (54) Revisions to the Delaware State Implementation Plan submitted 
on December 19, 1994 by the Delaware Department of Natural Resources & 
Environmental Control:
    (i) Incorporation by reference.
    (A) Letter of December 19, 1994 from the Delaware Department of 
Natural Resources & Environmental Control transmitting Regulation 24--
``Control of Volatile Organic Compound Emissions'', effective November 
29, 1994.
    (B) Regulation 24--``Control of Volatile Organic Compound 
Emissions'', Sections 10, 11, 12, 44, 45, 48, and 49 and appendices I, 
K, L, and M, effective November 29, 1994.
    (C) Administrative changes to Regulation 24, Section 2--Definitions: 
Addition of sections 2(c) Basecoat; 2(j) Clearcoat; 2(x) Gloss 
flattener; 2(bb) Internal Floating Roof; 2(gg) Liquid-mounted seal; 
2(ss) Petroleum; 2(tt) Petroleum Liquid; 2(xx) Primer; 2(jjj) Storage 
Vessel; 2(mmm) Transfer efficiency; 2(ppp) Vapor-mounted seal; and 
2(ttt) Volatile Organic Liquid (VOL); and section 2(zz) by changing ASTM 
D323-89 to ASTM D323-82, effective November 29, 1994.
    (D) An Errata sheet of Regulation 24 with administrative changes to 
Section 4--4(b) by renumbering section 13 to 10 and section 22 to 23, 
4(b)(1)(iii) by renumbering section 13 to 10 and section 22 to 23, 4(c) 
by renumbering section 22 to 23, 4(d) by renumbering section 22 to 23, 
4(e) by renumbering section 13 to 10

[[Page 256]]

and section 22 to 23, 4(e)(2)(iv) by adding the following lines: section 
10(e)(1)(iii), section 11(d), section 12(e)(1)(iii), and section 
23(e)(1)(iii), 4(e)(x) correcting 50 degrees F to 82 degrees F; Section 
8--8(a)(2) by renumbering section 13 to 10; Section 21--21(a)(5) 
correcting the number 4 to 5; Section 25--25(c)(4)(vi) by changing 
calibrated to calculated; Section 29--29(i)(3)(i)(A) by correcting 0.09 
to 0.044 in Hg, 29(i)(3)(i)(B) by correcting 0.09 to 0.044 in Hg; 
Section 30--30(b) by deleting definitions of liquid mounted seal and 
vapor mounted seal that were added in Section 2--Definitions; Section 
31--31(b) by deleting definition of internal floating roof that was 
added to Section 2--Definitions, 31(e)(ii) by correcting letter i to ii; 
Section 33--33(f)(3) by correcting (c)(3)(i)(B) to (c)(3)(ii)(B), 
Section 35--35(c)(2)(i) by adding weight, 35(c)(3)(i) by adding by 
weight; Section 37--37(a)(1) by deleting of press ready ink; Section 
43--43(a)(1) by renumbering section 13 to 10 and section 42 to 49; 
Appendix A--(a) by renumbering section 13(c)(1) or section 14 through 43 
to section 19 through 50; Appendix D--(a)(2)(iii)(4) by deleting to be 
published, effective November 29, 1994.
    (ii) Additional Material.
    (A) Remainder of December 19, 1994 State submittal pertaining to 
Regulation 24 referenced in paragraphs (c)(54)(i).
    (55) Revisions to the Delaware Regulations, Regulation 24, Section 
47--Offset Lithographic Printing submitted on December 19, 1994 by the 
Delaware Department of Natural Resources & Environmental Control 
(DNREC):
    (i) Incorporation by reference.
    (A) Letter of December 19, 1994 from the Delaware DNREC transmitting 
Regulation 24, Section 47--Offset Lithographic Printing, effective 
November 29, 1994.
    (B) Regulation 24, Section 47--Offset Lithographic Printing, 
effective November 29, 1994.
    (ii) Additional material from Delaware's December 19, 1994 submittal 
pertaining to Section 47 of Regulation 24.
    (58) Revisions to the Delaware State Implementation Plan on October 
2, 1996 by the Delaware Department of Natural Resources & Environmental 
Control:
    (i) Incorporation by reference.
    (A) A letter of October 2, 1996 from the Delaware Department of 
Natural Resources & Environmental Control transmitting the General 
Conformity Rule.
    (B) Delaware Regulation 35--Conformity of General Federal Actions to 
the State Implementation Plans (General Conformity), effective August 
14, 1996.
    (ii) Additional material from the Delaware's October 2, 1996 
submittal pertaining to Regulation 35.
[37 FR 10856, May 31, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.420, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.421  Classification of regions.

    The Delaware plan was evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                               Pollutant
                                                      ----------------------------------------------------------
              Air quality control region                                                           Photochemical
                                                       Particulate   Sulfur   Nitrogen   Carbon      oxidants
                                                          matter     oxides    dioxide  monoxide  (hydrocarbons)
----------------------------------------------------------------------------------------------------------------
Metropolitan Philadelphia Interstate.................           I          I       III         I             I
Southern Delaware Intrastate.........................         III        III       III       III           III
----------------------------------------------------------------------------------------------------------------

[37 FR 10856, May 31, 1972, as amended at 39 FR 16345, May 8, 1974]



Sec. 52.422  Approval status.

    (a) With the exceptions set forth in this subpart, the Administrator 
approves Delaware's plan for the attainment and maintenance of the 
national standards under section 110 of the Clean Air Act. Furthermore, 
the Administrator finds that the plan satisfies all requirements of part 
D, title 1, of the Clean Air Act as amended in

[[Page 257]]

1977, except as noted below. In addition, continued satisfaction of the 
requirements of part D for the ozone portion of the SIP depends on the 
adoption and submittal of RACT requirements by July 1, 1980, for the 
sources covered by CTGs issued between January 1978 and January 1979 and 
adoption and submittal by each subsequent January of additional RACT 
requirements for sources covered by CTGs issued by the previous January.
    (b) Letter of February 26, 1993, from the Delaware Department of 
Natural Resources and Environmental Control transmitting a commitment to 
adopt either the Federal clean fuel fleet program or an alternative 
substitute program by May 15, 1994.
[45 FR 14558, Mar. 6, 1980, as amended at 58 FR 50848, Sept. 29, 1993]



Sec. 52.423  1990 Base Year Emission Inventory.

    EPA approves as a revision to the Delaware State Implementation Plan 
the 1990 base year emission inventories for the Delaware ozone 
nonattainment areas submitted by the Secretary of the Department of 
Natural Resources and Environmental Control on May 27, 1994. This 
submittal consists of the 1990 base year point, area, non-road mobile, 
biogenic and on-road mobile source emission inventories in area for the 
following pollutants: volatile organic compounds (VOC), carbon monoxide 
(CO), and oxides of nitrogen (NOX).
[61 FR 1841, Jan. 24, 1996]



Sec. 52.424  Conditional approval.

    (a) EPA is conditionally approving as a revision to the Delaware 
State implementation plan the 15 Percent Rate of Progress Plan and 
associated contingency measures for the Delaware ozone nonattainment 
areas classified as severe, namely Kent and New Castle Counties, 
submitted by the Secretary of Delaware Department of Natural Resources 
and Environmental Control on February 17, 1995. EPA is also 
conditionally approving the I/M SIP in a separate rulemaking, as credits 
from that program are part of the 15 Percent RPP. By no later than one 
year from June 18, 1997, Delaware must submit a revised I/M SIP that 
meets the conditions stated in the I/M SIP final rulemaking. Once 
Delaware satisfies the conditions of its I/M rulemaking and receives 
full approval, EPA will fully approve the 15 Percent RPP SIP. 
Conversely, if the I/M rulemaking converts to a final disapproval, EPA's 
conditional approval of the 15 Percent RPP SIP would also convert to a 
disapproval.
    (b) The State of Delaware's February 17, 1995 submittal for an 
enhanced motor vehicle inspection and maintenance (I/M) program, and the 
November 30, 1995 submittal of the performance standard evaluation of 
the low enhanced program, is conditionally approved based on certain 
contingencies.
    The following conditions must be addressed in a revised SIP 
submission. Along with the conditions listed is a separate detailed I/M 
checklist explaining what is required to fully remedy the deficiencies 
found in the proposed notice of conditional approval. This checklist is 
found in the Technical Support Document (TSD), located in the docket of 
this rulemaking, that was prepared in support of the proposed 
conditional I/M rulemaking for Delaware. This checklist and Technical 
Support Document are available at the Air, Radiation, and Toxics 
Division, 841 Chestnut Bldg., Philadelphia, PA 19107, telephone (215) 
566-2183. By no later than 1 year from June 18, 1997, Delaware must 
submit a revised SIP that meets the following conditions for 
approvability, with the exception of condition item in paragraph (b)(3) 
of this section which addresses I/M program evaluation requirements. 
Condition in paragraph (b)(3) of this section must be met by November 
30, 1998, in keeping with the amended requirements of 40 CFR 51.353.
    (1) Provide a statement from an authorized official that the 
authority to implement Delaware's I/M program as stated above will 
continue through the attainment date and provide ZIP code information 
for the affected counties under the I/M program.
    (2) Submit to EPA adopted regulations or procedures that implement 
an on-road vehicle testing program and remodel its program and 
demonstrate compliance with the I/M parameter

[[Page 258]]

standard so that it meets all the requirements of 40 CFR 51.351.
    (3) Submit to EPA a description of the evaluation schedule and 
protocol, the sampling methodology, the data collection and analysis 
system, the resources and personnel for evaluation, and related details 
of the evaluation program, and the legal authority enabling the 
evaluation program that meet all the requirements of 40 CFR 51.353.
    (4) Submit to EPA procedures or regulations that detail the number 
of personnel and equipment dedicated to the quality assurance program, 
data collection, data analysis, program administration, enforcement, 
public education and assistance, on-road testing and other necessary 
functions that meet all the requirements of 40 CFR 51.354.
    (5) Submit to EPA procedures or regulations that meet the 
requirements of 40 CFR 51.355. This includes a description of the test 
year selection scheme, and how the test frequency is integrated into the 
enforcement process. This description must include the legal authority, 
regulations or contract provisions to implement and enforce the test 
frequency. The program must be designed to provide convenient service to 
the motorist by ensuring short wait times, short driving distances and 
regular testing hours.
    (6) Submit to EPA a description of vehicles covered by Delaware's I/
M program, broken down by model year, and weight; an accounting for 
registered vehicles and those required to be registered in order to 
provide an estimate of unregistered vehicles subject to the I/M program. 
Delaware also needs to submit provisions in its regulations that provide 
for fleet testing; testing vehicles registered in other program areas; 
and provide the legal authority or rules necessary to implement fleet 
testing. With regard to the fleet inspection program, Delaware needs to 
develop regulations and procedures that address fleet inspections and 
account for this in its vehicle coverage and in the modeling of the 
performance standard. In addition, Delaware must provide information on 
exempted vehicles regarding number, fleet percentage and account for 
them in its emissions reduction analysis. This submission must meet the 
requirements of 40 CFR 51.356.
    (7) Submit to EPA procedures or regulations that address the 
requirements of 40 CFR 51.357.
    (8) Submit to EPA regulations or procedures that address the 
requirements of 40 CFR 51.358.
    (9) Submit to EPA regulations or procedures that address the 
requirements of 40 CFR 51.359, including: a quality control procedures 
manual or related document; proper calibration measures and associated 
recordkeeping; preventive maintenance measures/provisions for proper 
recording of quality control information.
    (10) Submit to EPA regulations and/or procedures that address the 
requirements of 40 CFR 51.360. These include: provisions that implement 
a consumer price index (CPI) adjusted $450 waiver for Kent and New 
Castle Counties, where the low enhanced program applies.
    (11) Submit to EPA regulations and/or procedures that meet the 
requirements of 40 CFR 51.361, including providing EPA with the specific 
details of its Motorist Compliance Enforcement program, providing a 
commitment to maintain a specified enforcement level to be used for 
modeling purposes. Also Delaware must provide regulations and 
legislation that implement a registration denial system.
    (12) Submit to EPA regulations or procedures that meet the 
requirements of 40 CFR 51.362, including: providing procedures or 
regulations that detail how the motorist compliance enforcement 
oversight program will be implemented and a demonstration of the 
program's functionality.
    (13) Submit to EPA regulations or procedures that meet the 
requirements of 40 CFR 51.363, including: providing procedures or 
regulations that detail how the quality assurance motorist compliance 
enforcement oversight program will be implemented and a demonstration of 
the program's functionality.
    (14) Submit to EPA regulations or procedures that meet all the 
requirements of 40 CFR 51.364, including: providing the legal authority 
for establishing and imposing penalties, civil

[[Page 259]]

fines, license suspensions and revocations; providing quality assurance 
officials of the state with the authority to temporarily suspend station 
and/or inspector licenses immediately upon finding a violation that 
directly affects emissions reduction benefits, or an official opinion 
explaining any state constitutional impediments to such immediate 
suspension authority; and providing a description of the administrative 
and judicial procedures and responsibilities relevant to the enforcement 
process, including which agencies courts and jurisdictions are involved, 
who will prosecute and adjudicated cases and the resources and sources 
of the those resources which will support this function.
    (15) Demonstrate that Delaware has existing data procedures that 
meet the requirements of 40 CFR 51.365; or develop and submit to EPA 
regulations, or procedures that meet all the requirements of 40 CFR 
51.365.
    (16) Demonstrate that Delaware has existing data analysis procedures 
that meet the requirements of 40 CFR 51.366 or develop and submit 
provisions/ procedures that meet the requirements of 40 CFR 51.366.
    (17) Provide to the EPA details of the inspectors training course 
along with addressing all of the requirements of 40 CFR 51.367.
    (18) Provide to the EPA the details of the provisions and/or 
measures that will implement to protect the consumer and provide for the 
public awareness as well as address the rest of the requirements of 40 
CFR 51.368.
    (19) Provide to the EPA the details of the technician training 
course that it is developing and address the requirements of 40 CFR 
51.369.
    (20) Provide to the EPA documents and/or provisions that meet the 
requirements of 40 CFR 51.370, including: providing details of its 
provisions to ensure that vehicles subject to enhanced I/M and are 
included in an emission related to recall, receive the required repairs 
prior to completing the emissions test and or renewing the vehicle 
registration.
    (21) Meet the requirements of 40 CFR 51.371, including: adopting 
legislation that gives authority to implement an on-road testing 
program; providing details of an on-road testing program.
    (c) EPA is conditionally approving as a revision to the State 
Implementation Plan the New Source Review (NSR) program submitted by the 
Secretary of the Delaware Department of Natural Resources and 
Environmental Control on January 11, 1993. Delaware must provide a SIP 
revision which corrects the deficiencies in the NSR Regulation 
(Regulation No. 25) by April 5, 1999. Once Delaware satisfies the 
conditions of the NSR rulemaking, EPA will fully approve the NSR 
program. If a revised SIP meeting the conditions of the NSR rulemaking 
is not submitted by the date specified, the rulemaking will convert to a 
final disapproval. The approval is contingent on the State of Delaware 
revising its regulations to address the deficiencies noted in the 
Technical Support Document, (TSD) that was prepared in support of the 
proposed conditional approval rulemaking for Delaware's NSR program. 
Delaware must submit a SIP revision that includes the following:
    (1) The special rule for modifications of sources in serious and 
severe ozone nonattainment areas, consistent with sections 182(c)(7) and 
(8) of the Clean Air Act.
    (2) Public participation procedures consistent with 40 CFR 51.161. 
Regulation No. 25 does not specify the public participation procedures 
to be used in issuing nonattainment NSR permits.
    (3) A requirement that where the emissions limit under the SIP 
allows greater emissions than the potential to emit of the source, 
emission offset credit will be allowed only for control below this 
potential as found in 40 CFR 51.165(a)(3)(ii)(A).
    (4) Provisions for granting emission offset credit for fuel 
switching, consistent with 40 CFR 51.165(a)(3)(ii)(B).
    (5) Requirements consistent with 40 CFR 51.165(a)(3)(ii)(C)(1) for 
the crediting of emission reductions achieved by shutting down an 
existing source or curtailing production or operating hours below 
baseline levels (shutdown credits). These requirements must include a 
provision that such reductions may be credited if they are permanent, 
quantifiable and federally-enforceable,

[[Page 260]]

and if the area has an EPA-approved attainment plan.
    (6) A requirement that the shutdown or curtailment is creditable 
only if it occurred after the date of the most recent emissions 
inventory or attainment demonstration consistent with 40 CFR 
51.165(a)(3)(ii)(C)(1).
    (7) A requirement that all emission reductions claimed as offset 
credit shall be federally enforceable consistent with 40 CFR 
51.165(a)(3)(ii)(E).
    (8) Requirements for the permissible location of offsetting 
emissions consistent with 40 CFR 51.165(a)(3)(ii)(F) and section 
173(c)(1) of the CAA.
    (9) A requirement that credit for an emission reduction can be 
claimed to the extent that the State has not relied on it in issuing any 
permit under regulations approved pursuant to 40 CFR part 51 (i.e., the 
SIP), or the State has not relied on it in a demonstration of attainment 
or reasonable further progress.
[62 FR 27197-27199, May 19, 1997, as amended at 63 FR 1368, Jan. 9, 
1998; 63 FR 16435, Apr. 3, 1998]



Secs. 52.425--52.429  [Reserved]



Sec. 52.430  Photochemical Assessment Monitoring Stations (PAMS) Program.

    On March 24, 1994 the Delaware Department of Natural Resources & 
Environmental Control submitted a plan for the establishment and 
implementation of a Photochemical Assessment Monitoring Stations (PAMS) 
Program as a state implementation plan (SIP) revision, as required by 
section 182(c)(1) of the Clean Air Act. EPA approved the Photochemical 
Assessment Monitoring Stations (PAMS) Program on September 11, 1995 and 
made it part of the Delaware SIP. As with all components of the SIP, 
Delaware must implement the program as submitted and approved by EPA.
[60 FR 47084, Sept. 11, 1995]



Sec. 52.431  [Reserved]



Sec. 52.432  Significant deterioration of air quality.

    (a) The requirements of sections 160 through 165 of the Clean Air 
Act are not met, since the plan does not include approvable procedures 
for preventing the significant deterioration of air quality.
    (b) Regulation for preventing significant deterioration of air 
quality. The provisions of Sec. 52.21(l)(2) and (p) are hereby 
incorporated and made a part of the applicable State plan for the State 
of Delaware.
    (c) Pursuant to 40 CFR 52.21(u) full delegation of authority for all 
portions of the Federal PSD program, as described in 40 CFR 52.21, was 
relinquished to the State of Delaware as of June 15, 1981. All 
applications submitted as of that date and supporting information 
required pursuant to Sec. 52.21 from sources located in the State of 
Delaware shall be submitted to: Delaware Department of Natural Resources 
and Environmental Control, Air Resources Section, Division of 
Environmental Control, Edward Tatnall Building, P.O. Box 1401, Dover, 
Delaware 19901.
[45 FR 52741, Aug. 7, 1980, and 46 FR 31262, June 15, 1981, as amended 
at 47 FR 11014, Mar. 15, 1982]



Sec. 52.433  Requirements for state implementation plan revisions relating to new motor vehicles.

    Delaware must comply with the requirements of Sec. 51.120.
[60 FR 4737, Jan. 24, 1995]



Sec. 52.460  Small business stationary source technical and environmental compliance assistance program.

    (a) On January 11, 1993, the Director of the Delaware Department of 
Natural Resources and Environmental Control submitted a plan for the 
establishment and implementation of a Small Business Stationary Source 
Technical and Environmental Compliance Assistance Program as a State 
Implementation Plan revision, as required by title V of the Clean Air 
Act. EPA approved the Small Business Stationary Source Technical and 
Environmental Compliance Assistance Program on May 17, 1994, and made it 
a part of the Delaware SIP. As with all components of the SIP, Delaware 
must implement the program as submitted and approved by EPA.
[59 FR 25572, May 17, 1994]

[[Page 261]]



                     Subpart J--District of Columbia



Sec. 52.470  Identification of plan.

    (a) Title of plan: ``Implementation Plan for the Control of Carbon 
Monoxide, Nitrogen Dioxide, Hydrocarbons, and Oxidants.''
    (b) The above plan was officially submitted on January 31, 1972, by 
the Mayor/Commissioner.
    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) Control strategies for sulfur oxides and particulate matter were 
defined by the District's ``Implementation Plan for Controlling Sulfur 
Oxide and Particulate Air Pollutants'' submitted on August 14, 1970, by 
the District of Columbia.
    (2) Addition to Permit to Construct regulation, Section 8-2:720 of 
the District of Columbia Control Regulations, plus miscellaneous non-
regulatory revisions to the plan submitted April 28, 1972, by the 
District of Columbia.
    (3) Particulate matter emission rate graph submitted on January 29, 
1973, by the Department of Environmental Services.
    (4) Plan revisions were submitted on January 29, 1973, by the 
Department of Environmental Services.
    (5) Transportation Control Plans for the District of Columbia's 
portion of National Capital AQCR submitted on April 20, 1973, by the 
Mayor/Commissioner.
    (6) Amendments to the Transportation Control Plan for the District 
of Columbia submitted on July 9, 1973, by the Mayor/Commissioner.
    (7) Amendments to the Transportation Control Plan for the District 
of Columbia submitted on July 16, 1973, by the Mayor/Commissioner.
    (8) Amendments to Sections 8-2:702 (Definitions) and 8-2:707, 
(Control of Organic Compounds), subsections (a), (b), (c), (d), (e), and 
(f) of the District of Columbia Air Quality Control Regulations 
submitted on March 22, 1974 by the Mayor/Commissioner.
    (9) Amendments to Sections 8-2:704 and 8-2:705 of the District of 
Columbia Air Quality Control Regulations submitted on February 25, 1976 
by the Mayor.
    (10) Section 8-2:709 and Section 8-2:724 are amended to limit 
particulate emissions to .08 grains per day standard cubic foot at Solid 
Waste Reduction Center 1 (S.W.R.C. 1) and allow continued operation of 
S.W.R.C. 1 respectively; submitted July 17, 1975 by the District of 
Columbia.
    (11) Amendments to Sections 8-2:704 (Use of Certain Fuel Oils 
Forbidden), 8-2:705 (Use of Certain Coal Forbidden), and 8-2:713 
(Visible Emissions) of the District of Columbia Air Quality Control 
Regulations submitted on March 3, 1977 by the Mayor.
    (12) Amendments to Sections 8-2:702 (Definitions), 8-2:708 (Fuel 
Burning Particulate Emission) and 8-2:720 (Permits to Construct or 
Modify, Permits to Operate); an amendment deleting Appendix 1 from the 
District of Columbia Air Quality Control Regulations submitted by the 
Mayor on May 25, 1978.
    (13) Amendments to Sections 8-2:704 (Allowable Sulfur Content in 
Fuel Oil) and 8-2:705 (Allowable Sulfur Content in Coal) of the 
District's Air Quality Control Regulations submitted on December 27, 
1978, by Mayor Walter E. Washington is hereby approved until December 
31, 1980.
    (14)-(15) [Reserved]
    (16) Amendments to Sections 8-2:702 (Definition Changes), 8-2:708 
(Performance Testing), 8-2:713 (Visible Emissions), 8-2:718 (Emission 
Testing), 8-2:726 (Penalties) of the District's Air Quality Control 
Regulations, and Section 6-812(a)(5) (Penalties) of the District of 
Columbia's Air Quality Control Act submitted on December 27, 1978 by 
Mayor Walter E. Washington.
    (17) Amendments to Sections 8-2:704 (Allowable Sulfur Content in 
Fuel Oil) and 8-2:705 (Allowable Sulfur Content in Coal) of the 
District's Air Quality Control Regulations submitted on December 27, 
1978, by Mayor Walter E. Washington are approved indefinitely.
    (18) Amendments to Regulations I (Definitions), XXIV (Control of 
Volatile Organic Compounds Emissions) and XXV (Requirements for 
Preconstruction Review) submitted on March 19, 1980 by the Secretary, 
Delaware Department of Natural Resources and Environmental Control.
    (19) The Plan revision entitled ``Revisions to the Implementation 
Plan for

[[Page 262]]

the District of Columbia for Attainment of the National Ambient Air 
Quality Standards for Particulates, Oxidants and Carbon Monoxide'' for 
all areas designated nonattainment as of March 3, 1978 and September 12, 
1978 submitted on December 26, 1979 by the Mayor. Included was a request 
for revocation and/or revision of sections of subpart J which have been 
mooted by court decision (District of Columbia v. Costle, 567 F. 2d 1091 
(D.C. Cir. 1977)), Congressional action, or rescission by EPA.
    (20) Inspection and Maintenance Program Amendments to the 
transportation control portion of the nonattainment plan were submitted 
by the Mayor on September 7, 1979 and May 6, 1981.
    (21) Amendments to the District's Air Quality Control Regulations 
for control of particulate matter, carbon monoxide and ozone were 
submitted by the Mayor on June 23, 1981.
    (22) The Washington, DC Implementation Plan for maintaining the 
National Ambient Air Quality Standard for lead submitted on October 7, 
1982 by the Mayor.
    (23) Revision for Public Notification of Air Quality, submitted on 
December 5, 1983.
    (24) Revision for Conflict of Interest procedures, submitted on 
December 6, 1983.
    (25) Plan revision, excluding the required vehicle emission 
inspection program, providing for attainment of the Ozone and Carbon 
Monoxide Standards, submitted by the District of Columbia on December 
28, 1982 and April 15, 1983.
    (26) Revision to the 1982 District of Columbia Ozone and Carbon 
Monoxide Attainment Plan consisting of an approvable vehicle emission 
inspection and maintenance program, therefore, completing all necessary 
requirements for attainment of the Ozone and Carbon Monoxide standards; 
submitted by the Mayor on May 3, 1985. See paragraph (c)(25) of this 
section for date of original submittal.
    (i) Incorporation by reference.
    (A) Amendment to section 604 (Vehicle Inspection: Rejected Vehicles) 
of Title 18 of the District of Columbia Municipal Regulations as 
published in the District of Columbia Register on November 23, 1984.
    (27) Revisions to the State Implementation Plan submitted by the 
Mayor of the District of Columbia on June 21, 1985, which define and 
impose RACT to control volatile organic compound emissions from 
engraving and plate printing sources.
    (i) Incorporation by reference.
    (A) A letter from the Mayor of the District of Columbia dated June 
21, 1985, submitting revision to the District of Columbia State 
Implementation Plan, and a letter from the District of Columbia 
Department of Consumer and Regulatory Affairs dated April 1, 1992, 
formally submitting additional information supplementing the June 21, 
1985 submittal.
    (B) Section 710 of title 20, submitted June 21, 1985 and effective 
March 15, 1985.
    (28) Revisions to 20 District of Columbia Municipal Regulations 
(DCMR) pertaining to oxygenated gasoline submitted on October 22, 1993 
by the District of Columbia's Department of Consumer and Regulatory 
Affairs.
    (i) Incorporation by reference.
    (A) Letter of October 22, 1993 from the District of Columbia's 
Department of Consumer and Regulatory Affairs transmitting the 
oxygenated gasoline regulations.
    (B) District of Columbia Register dated July 30, 1993 containing 20 
DCMR chapter 1, Section 199 definitions for the terms blending plant, 
distributor, non-oxygenated gasoline, oxygenate, oxygenated gasoline, 
oxygenated gasoline control period, oxygenated gasoline control area, 
refiner, refinery, retailer, retail outlet, terminal, wholesale 
purchaser-consumer; Chapter 5, Section 500, subsections 500.4 and 500.5; 
chapter 5, section 502, subsection 502.18; Chapter 9, section 904, 
subsections 904.1 and 904.2, effective September 30, 1993.
    (ii) Additional material.
    (A) Remainder of October 22, 1993 District of Columbia submittal.
    (29)-(31) [Reserved]
    (32) Revisions to the District of Columbia Regulations State 
Implementation Plan submitted on October 22, 1993 by the Government of 
the District of Columbia Department of Consumer and Regulatory Affairs.

[[Page 263]]

    (i) Incorporation by reference.
    (A) Letter of October 22, 1993 from the Government of the District 
of Columbia Department of Consumer and Regulatory Affairs transmitting a 
revised regulation which require owners of stationary sources to submit 
emission statements annually.
    (B) D.C. ACT 10-56 amendments to District of Columbia Air Pollution 
Control Act of 1984, Section 20 DCMR 199, specifically the addition of 
new definitions, and the addition of Section 20 DCMR 500.7. Effective on 
September 30, 1993.
    (33)  [Reserved]
    (34) Revisions to Title 20 the District of Columbia Municipal 
Regulations (DCMR) on June 21, 1985 by the District of Columbia:
    (i) Incorporation by reference.
    (A) Letter of June 21, 1985 from the Mayor of the District of 
Columbia transmitting Act 5-165, representing the air pollution cotrol 
regulations codified in 20 DCMR.
    (B) The revised provisions of 20 DCMR, effective March 15, 1985, as 
described below:
    (1) Chapter 1--General.

Section 100  (Purpose, Scope, and Construction), subsections 100.1 
through 100.5
Section 101  (Inspection), subsection 101.1
Section 102  (Orders for Compliance), subsections 102.1 through 102.3
Section 104  (Hearings), subsections 104.1 through 104.5
Section 105  (Penalty), subsections 105.1 through 105.4
Section 106  (Confidentiality of Reports), subsections 106.1 and 106.2
Section 107  (Control Devices or Practices), subsections 107.1 through 
107.4
Section 199  The following definitions and abbreviations:

    Definitions (Section 199.1)--Added: Affected facility, Building, 
structure, facility, or installation, Cartridge filter, Component, 
Containers and conveyers of solvent, Crude oil, Cylinder wipe, Emission 
unit, Federally enforceable, Flexography, Fugitive emission, Gas 
services, Gas services for pipeline/valves and pressure relief valves, 
Gravure, Heatset, Hydrocarbon, Ink, Inking cylinder, Innovative control 
technology, Intaglio, Leaking component, Lease custody transfer, 
Letterpress, Letterset, Liquid service, Necessary preconstruction, Net 
emission increase, Offset printing process, Offset lithography, Paper 
wipe, Perceptible, leak, Petroleum solvent, Plate, Printing, Printing 
operation, Printing Unit, Refinery operator, Refinery unit, Routing, 
Secondary emissions, Substrate, Vacuum still, Valves not externally 
regulated, Water-based solvent, Wiping solution. Revised: Air pollution, 
Distillate oil, Dry cleaning, Existing source, Fugitive dust, 
Incinerator, Loading facilities, Person, Start-up, Stationary source, 
Vapor tight, Wipe cleaning.
    Unchanged from Section 8-2:702: Air Pollutant, Control Device, 
Conveyorized Degreaser, Cutback Asphalt, Cold Cleaner, District, 
Emission, Episode Stage, Fossil Fuel, Fossil-Fuel-Fired Steam-Generating 
Unit, Freeboard, Fuel Burning Equipment, Gasoline, Malfunction, Multiple 
Chamber Incinerator, Opacity, Open-top Vapor Degreaser, Organic 
Solvents, Particulate Matter, Photochemically Reactive Solvent, Process, 
Process Weight, Process Rate Per Hour, Ringelmann Smoke Chart, Smoke, 
Solid Waste, Standard Conditions, Submerged Fill Pipe, Volatile Organic 
Compounds.
    Abbreviations (Section 199.2)--Added: CFR, EPA, ppmv Unchanged from 
Section 8-2:702: B.T.U., cal., CO, COHs, cfm, g., Hi-Vol., hr., lb., 
max., NO2, No., ppm, psia, SO2, g/
m3, U.L.


    Note: Section 199 of Chapter 1 lists all of the applicable 
definitions and abbreviations, while Sections X99.1 and X99.2 of each 
chapter contain a cross-reference to definitions listed in Section 199.1 
and abbreviations listed in Section 199.2.


    (2) Chapter 4--Ambient Monitoring and Emergency Procedures.

Section 400  (Air Pollution Reporting Index), subsection 400.1
Section 401  (Emergency Procedures), subsections 401.1 through 401.4, 
401.2 through 401.8, 401.7 (duplicate) and 401.8 (duplicate)
Section 499  (Definitions and Abbreviations), subsections 499.1 and 
499.2

    (3) Chapter 5--Source Monitoring and Testing.

Section 500  (Source Monitoring and Testing), subsections 500.1 through 
500.3
Section 501  (Monitoring Devices), subsections 501.1 through 501.3
Section 502  (Sampling, Tests, and Measurements), subsections 502.1 
through 502.15 (except for subsections 502.11, 502.12, and 502.14)
Section 599  (Definitions and Abbreviations), subsections 599.1 and 
599.2

    (4) Chapter 6--Particulates.

Section 600  (Fuel-Burning Particulate Emission), subsections 600.1 
through 600.7
Section 601  (Rotary Cup Burners), subsections 601.1 and 601.2
Section 602  (Incinerators), subsections 602.1 through 602.6

[[Page 264]]

Section 603  (Particulate Process Emissions), subsections 603.1 through 
603.3
Section 604  (Open Burning), subsections 604.1 and 604.2
Section 605  (Control of Fugitive Dust), subsections 605.1 through 605.4
Section 606  (Visible Emissions), subsections 606.1 through 606.9
Section 699  (Definitions and Abbreviations), subsections 699.1 and 
699.2

    (5) Chapter 8--Asbestos, Sulfur and Nitrogen Oxides.

Section 801  (Sulfur Content of Fuel Oils), subsection 801.1
Section 802  (Sulfur Content of Coal), subsections 802.1 and 802.2
Section 803  (Sulfur Process Emissions), subsections 803.1 through 803.4
Section 804  (Nitrogen Oxide Emissions), subsection 804.1
Section 899  (Definitions and Abbreviations), subsections 899.1 and 
899.2


    (6) Appendices.

Appendix No. 1  (Emission Limits for Nitrogen Oxide)
Appendix No. 2  [Table of Allowable Particulate Emissions from Process 
Sources]
Appendix No. 3  [Allowable VOC Emissions under Section 710]

    (7) Deletion of the following SIP provisions:

Section 8-2:721  (Complaints and Investigations)
Section 8-2:730  (Independence of Sections)
Section 8-2:731  (Effective Date)

    The following definitions and abbreviations:
    Definitions: Act, Air quality standard of the District of Columbia, 
Dry cleaning operation, Freeboard ratio, Mayor, Vehicular fuel tank.
    Abbreviations: (Degree), VOC, ``%''.

    (ii) Additional material.
    (A) Remainder of June 21, 1985 District of Columbia submittal 
pertaining to the provisions listed above.
    (35)  [Reserved]
    (36) The carbon monoxide redesignation and maintenance plan for the 
District of Columbia submitted by the District of Columbia Department of 
Consumer and Regulatory Affairs on October 12, 1995, as part of the 
District of Columbia SIP. The emission inventory projections are 
included in the maintenance plan.
    (i) Incorporation by reference.
    (A) Letter of October 12, 1995 from the District of Columbia 
Department of Consumer and Regulatory Affairs requesting the 
redesignation and submitting the maintenance plan.
    (B) Maintenance Plan for the Metropolitan Washington Carbon Monoxide 
Nonattainment Area adopted on September 20, 1995.
    (ii) Additional material.
    (A) Remainder of October 12, 1995 State submittal.
    (37) Revisions to the District of Columbia Municipal Regulations 
submitted on May 2, 1997 and May 9, 1997 by the District of Columbia 
Department of Consumer and Regulatory Affairs:
    (i) Incorporation by reference.
    (A) Letter of April 29, 1997 from the Department of Consumer and 
Regulatory Affairs transmitting new source review (NSR) program.
    (B) Regulations adopted on April 29, 1997; Title 20 of the District 
of Columbia Municipal Regulations (DCMR) Chapter 2, sections 200 (as 
amended), 201, 202, 204 (as amended), 206, 299 and the amended 
definition of ``modification'' in Chapter 1, section 199.
    (ii) Additional material.
    (A) Remainder of May 2, 1997 State submittal.
    (B) District Register for May 9, 1997.
[37 FR 19814, Sept. 22, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.470, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.471  Classification of regions.

    The District of Columbia plan was evaluated on the basis of the 
following classifications:

----------------------------------------------------------------------------------------------------------------
                                                                                  Pollutant
                                                           -----------------------------------------------------
                Air quality control region                  Particulate   Sulfur   Nitrogen   Carbon
                                                               matter     oxides    dioxide  monoxide    Ozone
----------------------------------------------------------------------------------------------------------------
National Capital Interstate...............................           I          I       III         I          I
----------------------------------------------------------------------------------------------------------------

[37 FR 10857, May 31, 1972, as amended at 39 FR 16346, May 8, 1974; 46 
FR 61263, Dec. 16, 1981]

[[Page 265]]



Sec. 52.472  Approval status.

    (a) With the exceptions set forth in this subpart, the Administrator 
approves the District of Columbia's plan for the attainment and 
maintenance of the national standards.
    (b) With respect to the transportation control strategies submitted 
on April 19, July 9, and July 16, 1973, the Administrator approves the 
measures for parking surcharge, car pool locator, vehicle inspection, 
express bus lanes, increased bus fleet and service, elimination of free 
parking by private employers, with exceptions set forth in Secs. 52.476, 
52.483, 52.486, and 52.479.
    (c) With the exceptions set forth in this subpart, the Administrator 
approves the District of Columbia's plan for the attainment and 
maintenance of the national standards under section 110 of the Clean Air 
Act. Furthermore, the Administrator finds that the plan satisfies all 
requirements of Part D, Title 1, of the Clean Air Act as amended in 
1977.
    (d) Section 710 of title 20 of the District of Columbia Regulations 
is approved with the following condition: Any alternative controls or 
exemptions under section 710.8 approved or granted by the District of 
Columbia are subject to a public notice and public hearing requirements 
and must be submitted to EPA as SIP revisions. Such alternatives or 
exemptions are not effective until approved as SIP revisions by EPA.
    (e)  [Reserved]
    (f) Disapproval of revisions to the District of Columbia State 
Implementation Plan, District of Columbia Municipal Regulations (DCMR) 
Title 20, Sections 200, 201, 202, 204 and 299, pertaining to permitting 
of sources, and associated definitions in Section 199 submitted on June 
21, 1985 and October 22, 1993 by the Mayor of the District of Columbia 
(1985 submittal) and by the Administrator of the District of Columbia 
Environmental Regulation Administration (1993 submittal). The 
disapproved regulations include those applicable to major new and major 
modified sources wishing to locate in the District. A new source review 
program for such major sources is required under sections 182 and 184 of 
the Clean Air Act. There are many deficiencies in the DCMR permitting 
regulations. Some of these deficiencies are the lack of public notice 
and comment procedures for new and modified sources applying for 
construction permits, the existence of a provision that allows the Mayor 
to grant indefinite 1-month temporary permits to those sources whose 
permits he/she determines have been delayed because of his/her office, 
the inclusion of a major source operating permit program, the inclusion 
of a minor source operating permit program that does not meet Part D 
requirements of the Act, the exemption of certain fuel burning (nitrogen 
oxide emitting) sources, incorrect citations of the Clean Air Act, a 
provision that allows circumvention of the offset requirement, and the 
lack of the de minimis special modification provisions required in 
serious and severe ozone nonattainment areas (section 182(c)(6) of the 
Clean Air Act).
[38 FR 33709, Dec. 6, 1973, as amended at 46 FR 61263, Dec. 16, 1981; 57 
FR 34251, Aug. 4, 1992; 60 FR 5136, Jan. 26 1995; 60 FR 15486, Mar. 24, 
1995; 61 FR 2936, Jan. 30, 1996]



Sec. 52.473  Conditional approval.

    The District of Columbia's November 25, 1997 submittal, for an 
enhanced motor vehicle inspection and maintenance (I/M) program, is 
conditionally approved pending full implementation of the program by 
April 30, 1999. Should the Dictrict fail to fulfill this condition by 
April 30, 1999, this conditional approval will convert to a disapproval 
pursuant to CAA section 110(k). In that event, EPA would issue a letter 
to notify the District that the condition had not been met, and that the 
approval had converted to a disapproval.
[63 FR 29957, June 2, 1998]

    Effective Date Note:  At 63 FR 29957, June 2, 1998, Sec. 52.473 was 
added, effective July 2, 1998.



Sec. 52.474  1990 Base Year Emission Inventory.

    (a) EPA approves as a revision to the District of Columbia 
Implementation Plan the 1990 base year emission inventory for the 
Washington Metropolitan Statistical Area, submitted by Director, 
District of Columbia Consumer and Regulatory Affairs, on January 13, 
1994

[[Page 266]]

and October 12, 1995. This submittal consist of the 1990 base year 
stationary, area and off-road mobile and on-road mobile emission 
inventories in the Washington Statistical Area for the pollutant, carbon 
monoxide (CO).
    (b) EPA approves as a revision to the District of Columbia State 
Implementation Plan the 1990 base year emission inventory for the 
District's portion of the Metropolitan Washington DC ozone nonattainment 
area submitted by the Director, DCRA, on January 13, 1994. This 
submittal consists of the 1990 base year point, area, highway mobile, 
non-road and biogenic source emission inventories in the area for the 
following pollutants: Volatile organic compounds (VOC), carbon monoxide 
(CO), and oxides of nitrogen (NOX).
[61 FR 2936, Jan. 30, 1996, as amended at 62 FR 19679, Apr. 23, 1997]



Secs. 52.475--52.478  [Reserved]



Sec. 52.479  Source surveillance.

    (a) [Reserved]
    (b) The requirements of Sec. 51.213 are not met with respect to the 
strategies for carpool locator service. The remaining transportation 
measures in the previously federally-promulgated implementation plan 
have been mooted by court decision (District of Columbia v. Costle, 567 
F. 2d 1091 (D.C. Cir 1977)) or rescinded by EPA.
[46 FR 61263, Dec. 16, 1981, as amended at 51 FR 40677, Nov. 7, 1986]



Sec. 52.480  Photochemical Assessment Monitoring Stations (PAMS) Program.

    On January 14, 1994 the District of Columbia's Department of 
Consumer and Regulatory Affairs submitted a plan for the establishment 
and implementation of a Photochemical Assessment Monitoring Stations 
(PAMS) Program as a state implementation plan (SIP) revision, as 
required by section 182(c)(1) of the Clean Air Act. EPA approved the 
Photochemical Assessment Monitoring Stations (PAMS) Program on September 
11, 1995 and made it part of the District of Columbia SIP. As with all 
components of the SIP, the District of Columbia must implement the 
program as submitted and approved by EPA.
[60 FR 47084, Sept. 11, 1995]



Secs. 52.481--52.497  [Reserved]



Sec. 52.498  Requirements for state implementation plan revisions relating to new motor vehicles.

    The District of Columbia must comply with the requirements of 
Sec. 51.120.
[60 FR 4737, Jan. 24, 1995]



Sec. 52.499  Significant deterioration of air quality.

    (a) The requirements of sections 160 through 165 of the Clean Air 
Act are not met, since the plan does not include approvable procedures 
for preventing the significant deterioration of air quality.
    (b) Regulations for preventing significant deterioration of air 
quality. The provisions of Sec. 52.21 (b) through (w) are hereby 
incorporated and made a part of the applicable state plan for the 
District of Columbia.
[43 FR 26410, June 19, 1978, as amended at 45 FR 52741, Aug. 7, 1980]



Sec. 52.510  Small business assistance program.

    On October 22, 1993, the Administrator of the District of Columbia 
Environmental Regulation Administration submitted a plan for the 
establishment and implementation of a Small Business Technical and 
Environmental Compliance Assistance Program as a state implementation 
plan revision (SIP), as required by title V of the Clean Air Act. EPA 
approved the Small Business Technical and Environmental Compliance 
Assistance Program on August 17, 1994 and made it part of the District 
of Columbia SIP. As with all components of the SIP, the District of 
Columbia must implement the program as submitted and approved by EPA.
[59 FR 42168, Aug. 17, 1994]



                           Subpart K--Florida



Sec. 52.520  Identification of plan.

    (a) Title of plan: ``State of Florida Air Implementation Plan.''
    (b) The plan was officially submitted on January 27, 1972.

[[Page 267]]

    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) Notification of adoption of standard procedures to test and 
evaluate air pollution sources submitted on April 10, 1972, by the 
Florida Department of Pollution Control.
    (2) Miscellaneous non-regulatory additions to the plan submitted on 
May 5, 1972, by the Florida Department of Pollution Control.
    (3) Compliance schedules submitted on June 1, 1973, by the Florida 
Department of Pollution Control.
    (4) Compliance schedules submitted on August 6, 1973, by the Florida 
Department of Pollution Control.
    (5) Revision of the State permit system to include indirect sources, 
Section III, Chapter 17-2, submitted on September 25, 1973, by the 
Florida Department of Pollution Control.
    (6) Compliance schedules submitted on February 26, 1974, by the 
Florida Department of Pollution Control.
    (7) Identification of ten AQMA's submitted on May 30, 1974, by the 
Florida Department of Pollution Control.
    (8) Request that EPA defer identification of seven AQCR's submitted 
on September 25, 1974, by the Florida Department of Pollution Control.
    (9) Additional information relating to the September 25, 1974, 
deferral request submitted on November 21, 1974, by the Florida 
Department of Pollution Control.
    (10) Additional information relating to the September 25, 1974, 
deferral request submitted on January 9, 1975, by the Florida Department 
of Pollution Control.
    (11) Revision to SO2 emission limits for sulfur recovery 
plants and sulfuric acid plants submitted on February 12, 1975, by the 
Florida Department of Pollution Control.
    (12) Request for deletion of four AQMA's from the AQMA 
identification list submitted on March 31, 1975, by the Florida 
Department of Pollution Control.
    (13) Additional information supporting the March 31, 1975, deletion 
request submitted on April 9, 1975, by the Florida Department of 
Pollution Control.
    (14) Additional information supporting the March 31, 1975, deletion 
request submitted on April 15, 1975, by the Florida Department of 
Pollution Control.
    (15) Revised limits on sulfur dioxide emissions from fossil-fuel-
fired steam generators were submitted on July 26, 1975, by the 
Department of Environmental Regulation. (No action is taken on these new 
limits as they apply to Duval County.)
    (16) Revised ambient sulfur dioxide standards for Broward, Dade, and 
Palm Beach Counties, submitted on December 15, 1975, by the Florida 
Department of Environmental Regulation.
    (17) Revised burning rule for cold or frost protection, submitted on 
January 14, 1976, by the Florida Department of Environmental Regulation.
    (18) 1979 implementation plan revisions for nonattainment areas, 
(sulfur dioxide and ozone), submitted on April 30, 1979, as supplemented 
with August 27, 1979 and January 23, 1980 submittals by the Florida 
Department of Environmental Regulation.
    (19) Variance from particulate, sulfur dioxide, and visible emission 
limits of the plan for units of Florida Power and Light Company's Cape 
Canaveral, Ft. Myers, Manatee, Riviera, and Sanford plants, submitted on 
August 31, 1979, and June 23, 1980, by the Florida Department of 
Environmental Regulation. (The particulate variance for the Port 
Everglades and Turkey Point plants is disapproved.)
    (20) Limited variance from particulate, visible, and excess 
emissions limits granted to Florida Power and Light for Unit 4 of its 
Sanford station, submitted on February 4, 1980, by the Department of 
Environmental Regulation.
    (21) The implementation plan revision developed by the Florida DER 
for the Jacksonville and Tampa TSP secondary nonattainment areas under 
Part D of Title I of the CAA was submitted for EPA's approval on 
February 27, 1981. The control strategies, as approved and adopted for 
the local program agencies (the Duval County Bio-Environmental Services 
Division and the Hillsborough County Environmental Protection 
Commission) were submitted to EPA on March 16 and April 20, 1982, 
respectively.
    (22) Pursuant to section 127 of the Clean Air Act, the Florida 
Department

[[Page 268]]

of Environmental Regulation submitted on April 15, 1980 a revision to 
the SIP concerning provisions for public notification and awareness.
    (23) The air quality surveillance plan revision was submitted by the 
Florida Department of Environmental Regulation on December 11, 1979 and 
updates Florida's SIP to meet EPA requirements as set forth in 40 CFR 
part 58 (44 FR 27558, May 10, 1979).
    (24) Reformatting of the Rules and Regulations portion of the 
Florida State Implementation Plan, submitted on May 8, 1978, by the 
Florida Department of Environmental Regulation.
    (25) Revisions to the Sulfur Dioxide Emission Limiting Regulations 
applicable to specific Fossil Fuel Steam Generators, submitted on 
November 6, 1978, and February 3, 1979, by the Florida Department of 
Environmental Regulation.
    (26) Request for delegation of authority for PSD submitted on 
September 22, 1980, by the Department of Environmental Regulation.
    (27) Corrections in 1979 revisions for ozone nonattainment areas 
(Broward, Dade, Duval, Hillsborough, Orange, Palm Beach, and Pinellas 
Counties) submitted on May 28, 1980, by the Florida Department of 
Environmental Regulation to meet conditions of the conditional approval 
of March 18, 1980 (45 FR 17140).
    (28) Revised limits on visible emissions from new sulfuric and 
nitric acid plants and mass particulate emission limits new Portland 
cement plants, submitted on July 16, 1976, by the Department of 
Environmental Regulation.
    (29) Revised Opacity Limits for Monsanto Textile Co., Pensacola, 
Florida, submitted on December 19, 1979, by the Florida Department of 
Environmental Regulation.
    (30) Operating permit for Stauffer Chemical Company, submitted on 
August 4, 1980, by the Florida Department of Environmental Regulation, 
to satisfy a condition of the approval of the 1979 revisions for the 
Pinellas County SO2 nonattainment area.
    (31) Revised ambient CO and TSP standards applicable in Broward, 
Dade, and Palm Beach Counties, submitted on August 6, 1976, by the 
Florida Department of Environmental Regulation.
    (32) Set II VOC regulations, submitted on August 28, 1980, by the 
Florida Department of Environmental Regulation.
    (33) Amendments to Florida's continuous monitoring rule, submitted 
on January 27, 1978, by the Department of Environmental Regulation.
    (34) Revisions in Sections 17-2.21 and 17-2.32 of the Florida 
Administrative Code, adopting, in part, Federal NSPS and NESHAPS 
regulations, submitted by the Florida Department of Environmental 
Regulation on August 28, 1980.
    (35) Revision of gasoline bulk plant rule, submitted on October 15, 
1980, by the Florida Department of Environmental Regulation.
    (36) Variance granted to Florida Power and Light Company for Unit 4 
of its Sanford station, submitted on August 11, 1981, by the Department 
of Environmental Regulation. This variance is applicable until July 1, 
1984, or until thirty months after EPAapproval, whichever, is later, for 
particulate, visible, and sulfur dioxide emissions.
    (37) RACT emission limits and bubble provision for General Portland 
Inc., Tampa (FAC 17-2.650(2)(c)1.c.), submitted by the Florida 
Department of Environmental Regulation on August 11, 1981.
    (38) Revocation of complex source rules, submitted on August 11, 
1981, by the Florida Department of Environmental Regulation.
    (39) Emission limits for sources burning carbonaceous fuel, 
submitted on May 22, 1974, and January 21, 1981, and reformatted on 
August 11, 1981, by the Florida Department of Environmental Regulation.
    (40) Amendments to upset, startup and malfunction rule, submitted on 
August 12, 1976; revisions to section 17-2.05(14) FAC (excess emissions) 
and 17-2.05(6) Table II, E., FAC, fossil fuel steam generators-visible 
emissions, submitted on October 19, 1979; revision describing compliance 
testing for amendments in section 17-2.05 (14) and (6), submitted on 
September 24, 1980, by the Department of Environmental Regulation.
    (41) Reformatting of the rules and regulations portion of the 
Florida

[[Page 269]]

State Implementation Plan, submitted on August 11, 1981, by the Florida 
Department of Environmental Regulation.
    (42) Revised open burning and frost protection rule and ambient lead 
standard, submitted on December 23, 1981, by the Florida Department of 
Environmental Regulation.
    (43) On July 14, 1980, the Florida Department of Environmental 
Regulation (FDER) submitted a revision pertaining to deletion of the 
regulation on existing petroleum refineries in nonattainment areas and 
adding test methods for gasoline truck tanks, vapor collection systems, 
volatile organic compound (VOC) content of coating materials and 
gasoline bulk terminals for sources located in ozone nonattainment 
areas. On May 30, 1980, FDER submitted a revision establishing 
incremental compliance dates for existing VOC sources and extending 
final compliance dates for certain gasoline service stations. On 
December 23, 1981, FDER submitted a revision establishing test methods 
for certain VOC sources, adopting three definitions used in the test 
methods, and exempting six VOCs.
    (44) Revised SO2 limits for the Gannon Station of Tampa 
Electric Company, submitted on December 3, 1980, and associated methods 
of coal sampling and analysis, submitted on February 16, 1982, by the 
Florida Department of Environmental Regulation.
    (45) Revision of the commencement date of the COM test burn period 
for Florida Power and Light Co.'s Sanford Plant, Unit 4, submitted on 
March 30, 1982, by the Florida Department of Environmental Regulation.
    (46) Miscellaneous regulation changes, submitted on August 11, 1981, 
by the Florida Department of Environmental Regulation.
    (47) Point source emission testing methods submitted on December 30, 
1980, and May 29, 1981, by the Florida Department of Environmental 
Regulation.
    (48) Revised ambient standards and episode alert level for ozone, 
submitted on April 26, 1982, by the Florida Department of Environmental 
Regulation.
    (49) Changes in Open Burning and Frost Protection Fire Rule, 
submitted on November 15, 1982, by the Florida Department of 
Environmental Regulation.
    (50) Miscellaneous amendents to Chapter 17-2, submitted on December 
23, 1982, by the Florida Department of Environmental Regulation.
    (51) Regulations for Prevention of Significant Deterioration, 
submitted on December 23, 1981, and December 23, 1982, by the Florida 
Department of Environmental Regulation. (No action is taken on the 
provisions for review involving vessel emissions or nonattainment 
areas.)
    (52) Amendments to Chapter 17-2.650(1)(a) and 17-2.650(2)(a) 
submitted on February 18, 1983, by the Florida Department of 
Environmental Regulation. The amendments require all new and modified 
sources of particulate and volatile organic compounds located in 
nonattainment areas or in areas of influence for particulate matter to 
utilize Reasonably Available Control Technology (RACT) if they are not 
subject to Lowest Achievable Emissions Rate (LAER) provisions.
    (53) Changes to Florida Administrative Code (FAC), Chapter 17-2, 
submitted on August 12, 1983, and June 13, 1984, by the Florida 
Department of Environmental Regulation (FDER).
    (i) Incorporation by reference--
    (A) August 12, 1983, letter and April 17, 1984, certification of 
Administrative Rules filed with the Department of State, from the 
Florida Department of Environmental Regulation.
    (B) Amendments to Florida Administrative Code Rules 17-2.100(132), 
17-2.300 (1) and (2), 17-2.400 (1) through (5), 17-2.500(2)(e)3, 17-
2.500(2)(e)4.c.(i), 17-2.500(4)(b), 17-2.650(1)(a). These revisions were 
adopted on July 1, 1983, by the State of Florida Department of 
Environmental Regulation.
    (C) Amendments to Florida Administrative Code Rules 17-2.410 (1) and 
(3), and 17-2.460, approved on April 17, 1984, by the State of Florida 
Department of Environmental Regulation.
    (ii) Additional material--none.
    (54) TSP variance for Jacksonville Kraft Paper Company, submitted on 
September 2, 1983, by the Florida Department of Environmental 
Regulation.

[[Page 270]]

    (55) State implementation plan for lead, submitted by the Department 
of Environmental Regulation on September 17, 1984.
    (i) Incorporation by reference--
    (A) Amendments to Florida Administrative Code, Chapter 17.2-100, 
Definitions, and 17.2-500 and 510, Applicability (for New Source 
Review), adopted by the State on January 25, 1984, and September 17, 
1984 letter from the Florida Department of Environmental Regulation to 
EPA.
    (ii) Additional material--
    (A) Narrative submittal, including an attainment demonstration.
    (B) Emissions inventories for lead sources.
    (56) Amendments to the Florida Administrative Code (FAC) submitted 
by the Secretary of the Florida Department of Environmental Regulation 
(FDER) on May 30, 1985, which deals with source sampling.
    (i) Incorporation by reference.
    (A) Amendments to 17-2.700 FAC, which deals with source sampling 
procedures and conditions, adopted on April 3, 1985, by the FDER.
    (ii) Additional material.
    (A) None.
    (57) Changes to Florida Administrative Code (FAC) Chapter 17-2, 
submitted on May 31, 1985, by the Florida Department of Environmental 
Regulation (FDER).
    (i) Incorporation by reference.
    (A) May 31, 1985 letter from the Florida DER, and Amendments to FAC 
Chapters 17-2.100, 17-2.215, 17-2.540, 17-2.600, 17-2.700 and 17-2.753 
which were adopted by the FDER on April 11, 1985. Allow sulfur in the 
pelletized form to be shipped and handled in the State. Also establish 
new source review requirements, emission estimating procedures, emission 
limiting standards, and test procedures for elemental sulfur storage and 
handling facilities.
    (ii) Additional information.
    (A) None.
    (58) Visibility new source review regulations were submitted to EPA 
on September 23, 1985.
    (i) Incorporation by reference.
    (A) Letter of September 23, 1985, from the State of Florida 
Department of Environmental Regulation, and amendments to Rule 17-2.100 
FAC (Definitions), Rule 17-2.220 FAC (Public Notice and Comment), and 
Rule 17-2.500 FAC (Prevention of Significant Deterioration), adopted by 
the Florida Department of Environmental Regulation on July 25, 1985.
    (59) Post-1982 CO SIP revision for Dade County, submitted on 
September 19, 1986, by the Florida Department of Environmental 
Regulation.
    (i) Incorporation by reference--none.
    (ii) Other material.
    (A) Narrative description of analysis performed for CO.
    (B) Analysis of East Flagler Street Carbon Monoxide Exceedances--
Downtown Miami.
    (C) Description of Methodologies to Assess Eight-Hour Nighttime 
Carbon Monoxide Exceedances.
    (D) Identification and Analysis of Potential Carbon Monoxide 
Hotspots in Dade County, Florida.
    (E) Analysis of Transportation Control Measures (TCMs), Dade County/
Miami.
    (60) Stack height regulations were submitted on July 1 and November 
19, 1986, by the Florida Department of Environmental Regulation.
    (i) Incorporation by reference.
    (A) Revised FAC 17-2.100(177), added FAC 17-2.100(178), added FAC 
17-2.500(5)(h)6., and added FAC 17-2.510(4)(f), adopted on May 8, 1986.
    (B) Revised FAC 17-2.100(61) and revised FAC 17-2.270, adopted on 
September 30, 1986.
    (ii) Other material--none.
    (61) [Reserved]
    (62) Consent Order was submitted by EPA on August 14, 1986, by the 
Florida Department of Environmental Regulation.
    (i) Incorporation by reference.
    (A) A Consent Order for Smart-Pak Industries was adopted by the 
Florida Department of Environmental Regulation on June 17, 1986.
    (ii) Additional material--none.
    (63) Florida plan for the protection of visibility in Federal Class 
I areas submitted to EPA on August 27, 1987, by the Florida Department 
of Environmental Regulation (FDER) to satisfy the Part 2 visibility 
requirements.
    (i) Incorporation by reference.

[[Page 271]]

    (A) May 26, 1988, letter from the Florida Department of 
Environmental Regulation, and pages 20 and 21 of the Florida plan for 
the protection of visibility in Federal Class I areas containing the 
periodic review requirements satisfying 40 CFR 51.306(c), adopted by the 
Florida Department of Environmental Regulation on August 27, 1987.
    (ii) Additional material.
    (A) Narrative SIP titled ``The Florida Plan for the Protection of 
Visibility in Federal Class I Areas.''
    (64) [Reserved]
    (65) Changes to the Florida Administrative Code (FAC), Chapter 17-2, 
submitted to EPA on November 19, 1986, and June 12, 1987, by the Florida 
Department of Environmental Regulations.
    (i) Incorporation by reference.
    (A) November 19, 1986, and June 12, 1987, letters from the Florida 
Department of Environmental Regulation.
    (B) Amendments to Florida Administrative Code Rules 17-2.100(6), 
(21) and (118); 17-2.210 introductory text, (1) and (3)(r); 17-2.220(1), 
(2)(a)-(h); 17-2.300(3)(c)1. and (3)(c)2.; 17-2.310 introductory text; 
17-2.450(1)(a) and (2)(a);17-2.500(2)(e)4.a. (i) and (ii), (4)(a)1.a. 
and (4)(b)1.; 17-2.600(1)(d); and 17-2.700(2)(a)3.; Tables 500-1, 500-2, 
500-3, Table 700-1 and Table 700-2. These revisions were adopted on July 
1, 1983, and September 30, 1986, by the FloridaDepartment of 
Environmental Regulation.
    (ii) Additional material--none.
    (66) PM10 revisions for the Florida State Implementation 
FPlan were submitted on May 19, 1988 and July 18, 1989, by the Florida 
Department of Environmental Regulation. Miscellaneous corrective 
revisions were also submitted by the Florida Department of Environmental 
Regulation on July 18, 1989.
    (i) Incorporation by reference.
    (A) Revised regulations which became state-effective on May 30, 
1988:

    17-2.100--Definitions: (16)(a), (17), (61), (143), (173)(b), (202)
    17-2.300--Ambient Air Quality Standards: (3)(b)
    17-2.310--Maximum Allowable Increases (Prevention of Significant 
Deterioration Increments): (1)(a) and (2)(a)
    17-2.330--Air Alert: (1)(b) thru (f)
    17-2.340--Air Warning: (1)(b)
    17-2.350--Air Emergency: (1) Introductory paragraph, (1)(b) thru (e)
    17-2.400--Procedures for Designation and Redesignation of Areas: 
(1)(b)
    17-2.410--Designation of Areas Not Meeting Ambient Air Quality 
Standards (Nonattainment Areas): (2)(b), (3) thru (7)
    17-2.420--Designation of Areas Meeting Ambient Air Quality Standards 
(Attainment Areas): (2)
    17-2.430--Designation of Areas Which Cannot Be Classified As 
Attainment or Nonattainment (Unclassifiable Areas): (1)
    17-2.450--Designation of Prevention of Significant Deterioration 
(PSD) Areas: (1) Introductory paragraph and subparagraph (a)
    17-2.460--Designation of Air Quality Maintenance Areas: (4)
    17-2.500--Prevention of Significant Deterioration: (2)(e)4.b., 
(4)(e)3., (5)(f)3, Table 500-2 and Table 500-3
    17-2.600--Specific Source Emission Limiting Standards: (11)(a)3., 
7., 9., (11)(b)3.a., (11)(b)5.

    (B) Revised regulations which became state-effective on July 9, 
1989:

    17-2.100--Definitions: (37) and (145)
    17-2.210--Permits Required: (1) and (3)
    17-2.260--Air Quality Models
    17-2.300--Ambient Air Quality Standards: (2)
    17-2.340--Air Warning: (1)(c)
    17-2.410--Designation of Areas Not Meeting Ambient Air Quality 
Standards (Nonattainment Areas): (1) and (2)(a)
    17-2.420--Designation of Areas Meeting Ambient Air Quality Standards 
(Attainment Areas): (3) thru (5)
    17-2.430--Designation of Areas Which Cannot Be Classified As 
Attainment or Nonattainment (Unclassifiable Areas): (2) Introductory 
Paragraph
    17-2.460--Designation of Air Quality Maintenance Areas: (1) and (2)
    17-2.500--Prevention of Significant Deterioration: (1)(a)--(c)
    17-2.520--Sources Not Subject to Prevention of Significant 
Deterioration or Nonattainment Requirements.: Title
    17-2.540--Source Specific New Source Review Requirements: (2)(a)
    17-2.600--Specific Emission Limiting and Performance Standards: 
Title, Introductory paragraph, (1)(a)1., (2)(a)2.a.; (2)(b)1.; (4)(b)2.; 
(5)(a)1., 2., 3a.(i), and 4. Introductory paragraph; (5)(b); (6); 
(12)(a)1.; (12)(a)7.; (12)(b); (12)(c) Introductory paragraph; 
(12)(c)4., (13); and (14)
    17-2.610--General Particulate Emission Limiting Standards: Table 
610-1 and (3)(c)7.
    17-2.650--Reasonably Available Control Technology (RACT): 
(1)(c)3.a.(ii) and (iii); (1)(f) introductory paragraph; (1)(f)10.c.(i) 
and (iv); (2)(a)1., (b), (c) Introductory paragraph, (c)1.b. and c., 
(c)2.b.(ii), (c)3.b.(ii),

[[Page 272]]

(c)4.b, (c)5.a. Introductory paragraph, (c)5.a.iv. and v., (c)5.b.(i)-
(iv), (c)6.b.(i) and (iii), (c)7.b.(i) and (ii), (c)8. thru 10., 
(c)11.a. Introductory paragraph, (c)11.a.(vi), (c)11.b., and (c)12.; 
(2)(d)2.a., b. and c.
    17-2.660--Standard of Performances for New Stationary Sources 
(NSPS): (2)(b)
    17-2.700--Stationary Point Source Emissions Test Procedures: (1)(b) 
Introductory paragraph; (1)(d)1.b.(i), (2)(a)2., (2)(a)4. thru 9.; Table 
700-1; (4)(c)1.c.(i) and (ii); (6)(a)1.a., (b)1., (b)2.a. and b., 
(b)3.a. and b., (b)5., (b)6.a. thru c.,(b)7.b. thru e., (b)10., (b)(12), 
(b)16.b. and c., (b)18 thru 22, (b)24. thru 31., and (c)6.d.
    17-2.710--Continuous Monitoring Requirements: (1)(a)2.
    17-2.960--Compliance Schedules for Specific Source Emission Limiting 
Standards: (1)(c) and (d) Introductory paragraph; (1)(e).

    (ii) Additional material.
    (A) Letter of May 19, 1988, from the Florida Department of 
Environmental Regulation (FDER) submitting the SIP revisions.
    (B) Letter of July 18, 1989, from the FDER submitting additional SIP 
revisions.
    (67) [Reserved]
    (68) Revisions which were submitted on August 16 and November 8, 
1989, concerning Biological Waste Incinerators
    (i) Incorporation by reference. (A) Revisions to Florida 
Administrative Code, Chapter 17-2 which became state effective on August 
30, 1989.

    17-2.100  Definitions; 27, 28, 181, and 182
    17.2.600  Specific Source Emission Limiting Standards: (1)(a)1., 
(1)(b) Introductory paragraph, (1)(c) Introductory paragraph, (1)(d)
    17.2.700  Stationary Point Source Emissions Test Procedures:
    Table 700-1: 17-2.600(1)(a)-(e)
    17.2.710  Continuous Monitoring Requirements: paragraph (5)

    (B) Revisions to Florida Administrative Code, chapter 17-2 which 
became state effective on November 9, 1989.

    17-2.100  Definitions: 26 and 175

    (ii) Additional material. (A) Letter of August 16, 1989, from the 
Florida Department of Environmental Regulation submitting the SIP 
revision.
    (B) Letter of November 8, 1989, from the Florida Department of 
Environmental Regulation submitting the amendments to the August 16, 
1989, submittal.
    (69) Vehicle Anti-tampering and visible emissions regulations 
(Chapter 17-243 and Chapter 17-244 of the Florida Administrative Code 
respectively) which were submitted to EPA on March 20, 1990, and 
revisions to Chapter 17-243 submitted on June 18, 1990.
    (i) Incorporation by reference.
    (A) New Florida Administrative Code (FAC) regulations 17-243 
(Tampering with Motor Vehicle Pollution Control Equipment) and 17-244 
(Visible Emissions from Motor Vehicles) which became state effective on 
February 21, 1990.
    (B) Revisions to FAC Chapter 17-243 (Tampering with Motor Vehicle 
Air Pollution Control Equipment) which became state effective May 29, 
1990.
    (ii) Other material.
    (A) March 20, 1990, and June 18, 1990, letters from the Florida 
Department of Environmental Regulation.
    (70) Revisions to chaper 17-2 of the Florida Administrative Code 
which were submitted on July 12, 1990.
    (i) Incorporation by reference.
    (A) Amendments to the following rules of F.A.C. which become 
effective on July 13, 1990:

17-2.100 (21), (22), (119) and (126);
17-2.310 (preamble), (1)(c), (2)(c), and (3)(c);
17-2.450 (1)(a), (2)(a), and (3); and
17-2.500 (2)(e)4.b., (3)(f)3., 4(a)3., 4(b)1. thru 3.a.
introductory paragraph, 4(b)3.b. thru d., 4(b)3.e. introductory 
    paragraph and 4(b)3.e.(ii).

    (ii) Other material.
    (A) Letter of July 12, 1990, from the Florida Department of 
Environmental Regulation.
    (B) Minimum program elements.
    (71) The Florida Department of Environmental Regulation submitted an 
Order authorizing research and testing by the Florida Power & Light 
Company and the operating permit for the Orimulsion Fuel Test Burn at 
the Sanford Power Plant Unit No. 4 to EPA on October 11, 1990.
    (i) Incorporation by reference. (A) Florida Department of 
Environmental Regulation Order authorizing research and testing by the 
Florida Power & Light Company adopted on October 4, 1990.
    (B) Florida Power & Light operating permit number AC 64-180842, PSD-
FL-150 which becomes State-effective on January 7, 1991.

[[Page 273]]

    (ii) Other materials. (A) Letter of October 11, 1990, from the 
Florida Department of Environmental Regulation.
    (72) Revisions to Chapter 17-2 of the Florida Administrative Code 
which were submitted on August 16, 1989, and August 27, 1990.
    (i) Incorporation by reference.
    (A) Amendments to FAC 17-2.100(41), (153) and (217); 17-2.510(2)(a) 
introductory paragraph, 17-2.650(1)(a), (1)(b) title, (1)(b)2., (1)(c)1, 
(1)(d), (1)(e), (1)(f) introductory paragraph, (1)(f)2.a., (1)(f)3.a., 
(1)(f)5.b., (1)(f)6.a.(i), and (1)(f)14.a.(iii); which became State 
effective on August 30, 1989.
    (B) Amendments to FAC 17-2.100(220); 17-2.650(1)(b)2, (1)(d), 
(1)(e), (1)(f)4.a., and (1)(f)16.a.; 17-2.700 TABLE 700-1; and 17-2.965, 
which became State effective on September 13, 1990.
    (ii) Other material--None.
    (73) Regulations for a centralized vehicle Inspection/Maintenance 
(I/M) program. These revisions were submitted by the State of Florida, 
through the Florida Department of Environmental Regulation (FDER) on 
March 20, 1989.
    (i) Incorporated by reference.
    (A) Florida Administrative Code, Chapter 17-242, Mobile Source--
Vehicle Emission Standards and Test Procedures Rule which were adopted 
on January 31, 1989.
    (ii) Other material.
    (A) Letter of March 20, 1989, from the Florida Department of 
Regulation (FDER).
    (74) Vehicle Anti-tampering revisions (Chapter 17-243 of the Florida 
Administrative Code) which were submitted to EPA on January 24, 1991.
    (i) Incorporation by reference.
    (A) Revisions to FAC Chapter 17-243 (Tampering with Motor Vehicle 
Air Pollution Control Equipment) which became state effective January 2, 
1991, as follows:

17-243.200--Definitions: (1); (2) Introductory Paragraph and (a); and 
    (3) Introductory paragraph
17-243.300--Exemptions: (2); (3) Introductory paragraph and (b); (4) 
    Introductory paragraph, (b), (c) and (d)
17-243.400--Prohibitions
17-243.500--Certification: (1)(a) thru (d)
17-243.600--Enforcement: (2); (3) Introductory paragraph and (b), (4); 
    (6); and (7)

    (ii) Other material.
    (A) Letter dated January 24, 1991, from the Florida Department of 
Environmental Regulation.
    (75) Revisions to F.A.C. Chapter 17-242 (Motor Vehicle Emission 
Standards and Testing Procedures) which were submitted to EPA on March 
25, 1991.
    (i) Incorporation by reference.

    (A) Revision to F.A.C. 17-242 (Motor Vehicle Emission Standards and 
Testing Procedures) which were adopted March 1, 1991.

    Revision to F.A.C. Chapter 17-242 as follows:

17-242.100; and
17-242.200 (1), (6), (9), (11), (12), (15), (18), (26), (29) and (30); 
          and
17-242.300; and
17-242.400; and
17-242.500; and
17-242.600 (1-3(a)(3)), 3(a)(6-10), 5(a-f), 5(h), 6 and
17-242.700; and
17-242.800; and
17-242.900 (1), (2)(a), (2)(b), (2)(d) through (2)(g), (3), (4) and (5)

    (ii) Other material.
    (A) Letter of March 25, 1991, from the Florida Department of 
Environmental Regulation.
    (76) The Florida Department of Environmental Regulation submitted 
revisions to chapter 17-2 of the Florida Administrative Code which were 
submitted on January 14, 1992. These revisions incorporate Capture 
Efficiency Test Procedures for Volatile Organic Compound sources into 
the Florida Administrative Code.
    (i) Incorporation by reference.
    (A) Florida Administrative Code (FAC) 17-2.100 (32), (37), (38), 
(39), (40), (60), (61), (68), (95), (101), (117), (155), (163), (180), 
(218), (237), effective December 31, 1991.
    (B) FAC 17-2.650(1)(f) Introductory paragraph, 1., 2., 3., 4., 5., 
6., 7., 12., 14., 15., and 16., effective December 31, 1991.
    (C) FAC 17-2.700(6)(c)7, effective December 31, 1991.
    (D) FAC 17-2.700(7), effective December 31, 1991.
    (ii) Other material--None.
    (77)  [Reserved]
    (78) State Implementation Plan for chapters 17-296, and 17-297, Soil 
Thermal Treatment and Recodification of the Florida Administrative Code, 
chapter 17-2, Air Pollution, submitted by

[[Page 274]]

the Department of Environmental Regulation on November 23, 1992, and 
January 11, 1993, respectively.
    (i) Incorporation by reference.
    (A) The following chapters of the Florida Administrative Code, 
effective October 15, 1992:
    (1) 17-209, Local Air Pollution Programs,
    (2) 17-210, Stationary Sources General Requirements,
    (3) 17-212, Preconstruction Review,
    (4) 17-252, Gasoline Vapor Control,
    (5) 17-272, Ambient Air Quality Standards,
    (6) 17-273, Air Pollution Episodes,
    (7) 17-275, Air Quality Areas,
    (8) 17-296, Stationary Sources--Emission Standards,
    (9) 17-297, Stationary Sources--Emission Monitoring.
    (B) Revisions to the following Florida Administrative Code: Chapters 
17-296.200(162), 17-296.415, table 297.330-1: entry 17-296.415, 17-
297.500(6), Soil Thermal Treatment, effective November 17, 1992.
    (ii) Other material. None.
    (79) Revisions to the F.A.C. Chapter 17-252 which were submitted by 
the Florida Department of Environmental Protection on January 8, 1993. 
The submittal revised the regulations for vapor recovery.
    (i) Incorporation by reference.
    (A) Revision to F.A.C. 17-252 which was effective on February 2, 
1993: 17-252.100; 17-252.200(2-12); 17-252.300; 17-252.400; 17-252.500; 
17-252.800; 17-252.900
    (ii) Other material.
    (A) Letter of January 8, 1993, from the Florida Department of 
Environmental Regulation.
    (80) The Florida Department of Environmental Regulation has 
submitted revisions to chapter 403.0852 of the Florida Statutes on 
February 24, 1993. These revisions address the requirements of section 
507 of title V of the CAA and establish the Small Business Stationary 
Source Technical and Environmental Assistance Program (PROGRAM).
    (i) Incorporation by reference. Florida Statutes 403.031(20), 
403.0852 (1), (2), (3), (4), 403.0872(10)(b), 403.0873, 403.8051, 
effective on April 28, 1992.
    (ii) Other material. None.
    (81) The maintenance plan for Duval County submitted by the Florida 
Department of Environmental Protection on June 23, 1993, as part of the 
Florida SIP.
    (i) Incorporation by reference.
    (A) Duval County Ozone Ten Year Maintenance Plan including Emissions 
Inventory Summary and Projections effective on August 23, 1994.
    (ii) Other material. None.
    (82) Revisions to chapter 17-296 and 17-297 of the Florida 
Administrative Code (FAC) regarding animal crematories and human 
crematories submitted on October 8, 1992, and December 9, 1993, 
respectively.
    (i) Incorporation by reference.
    (A) Amendments to FAC 17-2.600(d) and 17-2.700 and Table 700-1, 
adopted September 24, 1992.
    (B) Amendments to FAC 17-296.200(84), 17-296.401(5), 17-297.330, 
Table 17-297.330-1 and 17-297.500(7), adopted November 12, 1992.
    (ii) Additional information. None.
    (83) Revisions to Chapter 17-296 of the Florida Administrative Code 
(FAC) regarding Stationary Sources submitted on July 2, 1993.
    (i) Incorporation by reference.
    (A) Amendments to FAC 17-296.405 and 17-296.406, adopted June 9, 
1993.
    (84) Revisions to Florida Administrative Code Chapters 1709242 and 
1709275 which were effective February 2, 1993.
    (i) Incorporation by reference.
    (A) Revisions to Florida Administrative Code 1709242 and 1709275 
which were effective February 2, 1993.17.242.200(2), (16), (22), 
(250926), (29), (31); 17.242.400(2093), (4)(a), (4)(b), (5) introductory 
text and (5)(a);1709242.500(1)(a-b), (3)(b)1.; 1709242.600(2), (3) 
introductory text, (3)(a)1., (3)(a)7., (3)(c), (5)(d); 1709242.700 (4) 
introductory text, (4)(a), (4)(c-d), (5); 1709242.800(1), 
1709242.900(1)(b), (2), (3)(c), (4); 1709275.100; 1709275.200 
introductory text, (15), (170918); 275.300(1)(c), (3) introductory 
text,(3)(a), (3)(b)introductory text, (3) introductory text, (3)(b) 
introductory text, (3)(b)2. introductory text, (3)(b)2.b.-c., (3)(b)3. 
introductory text, (3)(b)3.a.; 17.275.400(2095); 1709275.410(1093),(6); 
1709275.420(1);1709275.600(1),(2) introductory text, (2)(b-c)
    (ii) Other material. None.

[[Page 275]]

    (85) Revisions to the State of Florida State Implementation Plan 
(SIP) concerning emission statements were submitted on January 12, 1993 
by the Florida Department of Environmental Protection.
    (i) Incorporation by reference.
    (A) Revisions to the following Florida Regulations were effective 
February 9, 1993. F.A.C. 17-210.100; 17-210.200(47), (49), (52) and 
(64); 17-210.370; and 17-210.900.
    (ii) Other material. None.
    (86) The maintenance plan for Southeast Florida submitted by the 
Florida Department of Environmental Protection on November 8, 1993, as 
part of the Florida SIP.
    (i) Incorporation by reference.
    (A) Southeast Florida Ozone Ten Year Maintenance Plan including 
Emissions Inventory Summary and Projections effective on November 8, 
1993.
    (ii) Other material. None.
    (87) Revisions to the Florida State Implementation Plan submitted by 
the Department of Environmental Protection on December 10, 1996.
    (i) Incorporation by reference. Section 62-210.200(1), (29)(g), 
(77)(a), (b), (137), (145)(a)29., (167), (259)(a)3-5 and (b), (309(y), 
and 62-210.220 of the Florida SIP effective October 15, 1996.
    (ii) Other material. None.
    (88) Revisions to the F.A.C. Chapters 17-212 and 17-296 which were 
effective February 2, 1993
    (i) Incorporation by reference.
    (A) Revision to F.A.C. 17-212, and 17-296 which were effective on : 
February 2, 1993. 17-212.100; 17-212.200 introductory paragraph, 
(5),(12),(57),(63)(e),(64),(75); 17-212.400 introductory paragraph,(2) 
introductory paragraph, (2)(f)3; 17-212.500(2)(a), (2)(a) introductory 
paragrpah, 2(a)2. introductory paragraph, 2(a)2.a., (2)(a)2.e.4.,(4)(b), 
(4)(c),(4)(d)1., (4)(d)2.a.-c., (4)(g), (5)(a), (5)(b)2.,4.-7.. 9.;17-
296.200(13), (50), (198); 17.500 introductory paragraph,(1); 17-
296.570(3).
    (B) Revision to F.A.C. 17-296 which became effective on April 17, 
1994. 17-296.500(1)(b), (2)(a)(1), (2)(b)(1), (2)(c), (6); 17-296.570(1-
2), (4).
    (ii) Other material.
    (A) Letters of January 8, 1993 and April 25, 1994, from the Florida 
Department of Environmental Protection.
    (89) The maintenance plan for Tampa, Florida, submitted by the 
Florida Department of Environmental Protection on February 7, 1995.
    (i) Incorporation by reference. Tampa Redesignation Request and 
Attainment/Maintenance Plan for the Tampa Bay Florida Ozone 
Nonattainment Area including Emissions Inventory Summary and Projections 
adopted on November 16, 1994.
    (ii) Other material. None.
    (90) Revisions to Chapter 62-210, Stationary Sources--General 
Requirements, submitted by the Florida Department of Environmental 
Protection on December 21, 1994 and April 24, 1995.
    (i) Incorporation by reference.
    (A) Revised Sections 62-210.300, ``Permits Required'', except 62-
210.300(2)(b)1., and 62-210.350, ``Public Notice and Comment'', 
effective November 23, 1994. Revised Section 62-210.300(2)(b)1., 
effective April 18, 1995.
    (91) The State of Florida submitted revisions to the FDEP 
Administrative Code for the Air Pollution Control Program on August 18, 
1994. These revisions provide for the control of lead emissions from 
facilities in the State of Florida, and will replace the Federal 
Implementation Plan requirements codified in 40 CFR 52.535.
    (i) Incorporation by reference. Chapters 17-296.200 (97) and (163) 
introductory paragraph and (e), 17-296.600-605 effective on August 8, 
1994.
    (ii) Other material. None.
    (92) The Florida Department of Environmental Protection has 
submitted revisions to the Florida State Implementation Plan on August 
12, 1994. These revisions address including the Small Business 
Stationary Source Technical and Environmental Program in the Florida 
Administrative Code, Chapter 17-202.
    (i) Incorporation by reference.
    (A) Chapter 17-202, Small Business Stationary Source Technical and 
Environmental Compliance Assistance Program adopted on June 30, 1994.
    (ii) Additional material. None.
    (94) Revisions to the Florida SIP regarding perchloroethylene dry 
cleaning facilities submitted on April 24, 1995.

[[Page 276]]

    (i) Incorporation by reference.
    Sections 62-210.200(17) and (48)(c); 62-210.300(2)(b) and (4); 62-
296.200(58); and 62-296.412 of the F.A.C., effective April 18, 1995.
    (ii) Other material. None.
    (95)  [Reserved]
    (96) Nine variances to F.A.C. Chapter 62-252 were submitted by the 
Florida Department of Environmental Protection on April 8, 1996. The 
submittal granted variances from the regulations for vapor recovery for 
nine facilities.
    (i) Incorporation by reference.
    (A) Florida Department of Environmental Protection Order Granting 
Variance effective February 28, 1996 for: FAC #508514770; FAC 
#508944721; FAC #508630588; FAC #50863023; FAC #508514723; FAC 
#508514722; FAC #508514484; FAC #508513991; FAC #508841861.
    (ii) Other material. None.
    (97) General permit rules and exclusionary rules for the State of 
Florida Department of Environmental Protection submitted by the Florida 
Department of Environmental Protection as part of the Florida SIP.
    (i) Incorporation by reference.
    (A) Florida Administrative Code Regulation 62-210.300(3)(c) and 62-
210.300(4) of the Florida SIP as adopted by the Secretary of the Florida 
Department of Environmental Protection on July 26, 1996 and which became 
effective on August 15, 1996.
    (ii) Other material. None.
    (98) Revisions to the Florida SIP to amend the gasoline tanker truck 
leak testing procedures, change the requirements to submit test results 
and update the gasoline tanker truck leak test form which were submitted 
on September 25, 1996.
    (i) Incorporation by reference.
    62-252.500(3) and 62-252.900, effective September 10, 1996.
    (ii) Other material. None.
[37 FR 10858, May 31, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.520, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.

    Effective Date Note:  At 63 FR 28906, May 27, 1998, Sec. 52.520 was 
amended by revising paragraph (c)(87), effective July 27, 1998. For the 
convenience of the user, the superseded text is set forth as follows:

Sec. 52.520  Identification of plan.

                                * * * * *

    (c) * * *
    (87) Revisions to chapter 17-256 of the Florida Administrative Code 
(FAC) regarding Open Burning submitted on July 9, 1991.
    (i) Incorporation by reference. Amendments to FAC 17-256.450, 
effective June 27, 1991.
    (ii) Other material. None.

                                * * * * *



Sec. 52.521  Classification of regions.

    The Florida plan was evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                               Pollutant
                                                      ----------------------------------------------------------
              Air quality control region                                                           Photochemical
                                                       Particulate   Sulfur   Nitrogen   Carbon      oxidants
                                                          matter     oxides    dioxide  monoxide  (hydrocarbons)
----------------------------------------------------------------------------------------------------------------
Mobile (Alabama)-Pensacola-Panama City (Florida)-
 Southern Mississippi Interstate.....................           I          I       III       III             I
Jacksonville (Florida)-Brunswick (Georgia) Interstate           I         II       III       III             I
West Central Florida Intrastate......................           I          I       III       III           III
Central Florida Intrastate...........................          II        III       III       III           III
Southwest Florida Intrastate.........................         III        III       III       III           III
Southeast Florida Intrastate.........................          II        III       III       III           III
----------------------------------------------------------------------------------------------------------------

[37 FR 10858, May 31, 1972, as amended 39 FR 16346, May 8, 1974]



Sec. 52.522  Approval status.

    With the exceptions set forth in this subpart, the Administrator 
approves Florida's plans for the attainment and maintenance of the 
national standards under section 110 of the Clean Air Act. Furthermore, 
the Administrator finds

[[Page 277]]

the plans satisfy all requirements of Part D, Title I, of the Clean Air 
Act as amended in 1977, except as noted below. In addition, continued 
satisfaction of the requirements of Part D, for the ozone portion of the 
SIP depends on the adoption and submittal of RACT requirements by July 
1, 1980 for those sources covered by CTGs issued between January 1978 
and January 1979 and adoption and submittal by each subsequent January 
of additional RACT requirements for sources covered by CTGs issued by 
the previous January.
[45 FR 17143, Mar. 18, 1980]



Sec. 52.523  [Reserved]



Sec. 52.524  Compliance schedules.

    (a) The requirements of Sec. 51.262(a) of this chapter are not met 
since compliance schedules with adequate increments of progress have not 
been submitted for every source for which they are required.
    (b) Federal compliance schedules. (1) Except as provided in 
paragraph (b)(6) of this section, the owner or operator of any 
stationary source subject to the following emission limiting regulations 
in the Florida implementation plan shall comply with the compliance 
schedule in paragraph (b)(2) of this section, Rules of the State of 
Florida, Department of Pollution Control, Air Pollution, subsections 17-
2.04(2); 17-2.04(3); 17-2.04(6)(a); 17-2.04(6)(b); 17-2.04(6)(d); 17-
2.04(6) (e)2.a; 17-2.04(6)(e)3.b; 17-2.04(6)(f); and 17-2.04(6)(h).
    (2) Compliance schedule. (i) November 1, 1973--Submit to the 
Administrator a final control plan, which describes at a minimum the 
steps which will be taken by the source to achieve compliance with the 
applicable regulations.
    (ii) January 1, 1974--Negotiate and sign all necessary contracts for 
emission control systems or process modifications, or issue orders for 
the purchase of component parts to accomplish emission control or 
process modification.
    (iii) February 1, 1974--Initiate onsite construction or installation 
of emission control equipment or process modification.
    (iv) May 1, 1975--Complete onsite construction or installation of 
emission control equipment or process modification.
    (v) July 1, 1975--Achieve compliance with the applicable 
regulations, and certify such compliance to the Administrator.
    (vi) If a performance test is necessary for a determination as to 
whether compliance has been achieved, such a test must be completed by 
July 1, 1975. Ten days prior to such a test, notice must be given to the 
Administrator to afford him the opportunity to have an observer present.
    (vii) Five days after the deadline for completing paragraphs (b)(2) 
(ii) through (iv) in this section, certify to the Administrator whether 
the increment has been met.
    (3) Except as provided in paragraph (b)(6) of this section, the 
owner or operator of any boiler or furnace of more than 250 million Btu 
per hour heat input subject to the requirements of Rules of the State of 
Florida, Department of Pollution Control, Air Pollution, subsections 17-
2.04(6)(e)2. c. and d. contained as part of the Florida Implementation 
Plan shall notify the Administrator, no later than October 1, 1973, of 
his intent to utilize either low-sulfur fuel or stack gas 
desulfurization to meet these requirements.
    (4) Any owner or operator of a stationary source subject to 
paragraph (b)(3) of this section who elects to utilize low-sulfur fuel 
shall be subject to the following compliance schedule:
    (i) November 1, 1973--Submit to the Administrator a projection of 
the amount of fuel, by types, that will be substantially adequate to 
enable compliance with the applicable regulation on July 1, 1975, and 
for at least one year thereafter.
    (ii) December 31, 1973--Sign contracts with fuel suppliers for fuel 
requirements as projected above.
    (iii) January 31, 1974--Submit a statement as to whether boiler 
modifications will be required. If modifications will be required, 
submit plans for such modifications.
    (iv) March 15, 1974--Let contracts for necessary boiler 
modifications, if applicable.

[[Page 278]]

    (v) June 15, 1974--Initiate onsite modifications, if applicable.
    (vi) March 31, 1975--Complete onsite modifications, if applicable.
    (vii) July 1, 1975--Achieve compliance with the requirements of 
Florida Air Pollution Rules subsections 17-2.04(6)(e)2. c. and d. and 
certify such compliance to the Administrator.
    (viii) If a performance test is necessary for a determination as to 
whether compliance has been achieved, such a test must be completed by 
July 1, 1975. Ten days prior to such a test, notice must be given to the 
Administrator to afford him the opportunity to have an observer present.
    (ix) Five days after the deadline for completing paragraphs (b)(4) 
(ii) through (vi) of this section, certify to the Administrator whether 
the increment has been met.
    (5) Any owner or operator subject to paragraph (b)(3) of this 
section, who elects to utilze stack gas desulfurization shall be subject 
to the compliance schedule in paragraph (b)(2) of this section.
    (6) (i) None of the above paragraphs shall apply to a source which 
is presently in compliance with applicable regulations and which has 
certified such compliance to the Administrator by October 1, 1973. The 
Administrator may request whatever supporting information he considers 
necessary for proper certification.
    (ii) Any compliance schedule adopted by the State and approved by 
the Administrator shall satisfy the requirements of this paragraph for 
the affected source.
    (iii) Any owner or operator subject to a compliance schedule in this 
paragraph may submit to the Administrator no later than October 1, 1973, 
a proposed alternative compliance schedule. No such compliance schedule 
may provide for final compliance after the final compliance date on the 
applicable compliance schedule of this paragraph. If promulgated by the 
Administrator, such schedule shall satisfy the requirements of this 
paragraph for the affected source.
    (7) Nothing in this paragraph shall preclude the Administrator from 
promulgating a separate schedule for any source to which the application 
of the compliance schedule in paragraph (b) (2) or (4) of this section 
fails to satisfy the requirements of Secs. 51.261 and 51.262(a) of this 
chapter.
[38 FR 16145, June 20, 1973, as amended at 38 FR 22740, Aug. 23, 1973; 
38 FR 24333, 24342, Sept. 7, 1973; 38 FR 26325, Sept. 19, 1973; 40 FR 
11724, 11725, Mar. 13, 1975; 51 FR 40676, 40677, Nov. 7, 1986; 54 FR 
25258, June 14, 1989]



Sec. 52.525  General requirements.

    (a) The requirements of Sec. 51.116(c) of this chapter are not met 
since the legal authority to provide for public availability of emission 
data is inadequate.
    (b) Regulation for public availability of emission data. (1) Any 
person who cannot obtain emission data from the Agency responsible for 
making emission data available to the public, as specified in the 
applicable plan, concerning emissions from any source subject to 
emission limitations which are part of the approved plan may request 
that the appropriate Regional Administrator obtain and make public such 
data. Within 30 days after receipt of any such written request, the 
Regional Administrator shall require the owner or operator of any such 
source to submit information within 30 days on the nature and amounts of 
emissions from such source and any other information as may be deemed 
necessary by the Regional Administrator to determine whether such source 
is in compliance with applicable emission limitations or other control 
measures that are part of the applicable plan.
    (2) Commencing after the initial notification by the Regional 
Administrator pursuant to paragraph (b)(1) of this section, the owner or 
operator of the source shall maintain records of the nature and amounts 
of emissions from such source and any other information as may be deemed 
necessary by the Regional Administrator to determine whether such source 
is in compliance with applicable emission limitations or other control 
measures that are part of the plan. The information recorded shall be 
summarized and reported to the Regional Administrator, on forms 
furnished by the Regional Administrator, and shall be submitted within 
45 days after the end of the reporting period. Reporting periods are

[[Page 279]]

January 1 to June 30 and July 1 to December 31.
    (3) Information recorded by the owner or operator and copies of this 
summarizing report submitted to the Regional Administrator shall be 
retained by the owner or operator for 2 years after the date on which 
the pertinent report is submitted.
    (4) Emission data obtained from owners or operators of stationary 
sources will be correlated with applicable emission limitations and 
other control measures that are part of the applicable plan and will be 
available at the appropriate regional office and at other locations in 
the state designated by the Regional Administrator.
[39 FR 34536, Sept. 26, 1974, as amended at 40 FR 55328, Nov. 28, 1975; 
51 FR 40676, Nov. 7, 1986]



Sec. 52.526  Legal authority.

    (a) The requirements of Sec. 51.230(f) of this chapter are not met, 
since section 403.111 of the Florida Statutes could, in some 
circumstances, prohibit the disclosure of emission data to the public. 
Therefore, section 403.111 is disapproved.
[39 FR 34536, Sept. 26, 1974, as amended at 51 FR 40676, Nov. 7, 1986]



Sec. 52.527  Control strategy: General.

    (a) Since the testing and research rule (FAC 17-1.585) submitted by 
the Florida Department of Environmental Regulation on April 7, 1980, as 
a revision of the plan does not meet the requirements of Section 110 of 
the Clean Air Act and the requirements of section 51.8 of this chapter, 
it is disapproved, and is not part of the plan.
    (b) [Reserved]
[48 FR 52303, Nov. 17, 1983]



Sec. 52.528  Control strategy: Sulfur oxides and particulate matter.

    (a) In a letter dated October 10, 1986, the Florida Department of 
Environmental Regulation certified that no emission limits in the 
State's plan are based on dispersion techniques not permitted by EPA's 
stack height rules.
    (b) The variance granted to the Turkey Point and Port Everglades 
plants of Florida Power and Light Company from the particulate emission 
limits of the plan is disapproved because the relaxed limits would cause 
violation of the Class I increment for sulfur dioxide in the Everglades 
National Park. These plants must meet the 0.1/MMBTU particulate limit 
of the plan.
[48 FR 33868, July 26, 1983, as amended at 54 FR 25455, June 15, 1989]



Sec. 52.529  [Reserved]



Sec. 52.530  Significant deterioration of air quality.

    (a) EPA approves the Florida Prevention of Significant Deterioration 
(PSD) rule on condition that the State submit to EPA by December 14, 
1983, a demonstration that its method of calculating increment 
consumption is consistent with Federal law and regulations. After 
receipt of the submittal and consideration of additional comments, EPA 
will, if it finds the State's method to be consistent, fully approve the 
Florida plan. If not, the State will change its regulation to implement 
EPA's approach.
    (b) Pending final full approval of the State's PSD plan by EPA, if a 
source's application can be approved under Florida's rules, but not 
under EPA's rules, solely because of the different methods of 
calculating increment consumption, the source must obtain a PSD permit 
from EPA before beginning construction.
    (c) All applications and other information required pursuant to 
Sec. 52.21 of this part from sources located in the State of Florida 
shall be submitted to the Florida Department of Environmental 
Regulation, Bureau of Air Quality Management, Twin Towers Office 
Building, 2600 Blair Stone Road, Tallahassee, Florida 32301.
    (d) The requirements of sections 160 through 165 of the CAA are not 
met since the Florida plan, as submitted, does not apply to certain 
sources. Therefore, the provisions of Sec. 52.21(b) through (w) are 
hereby incorporated by reference and made a part of the Florida plan 
for:
    (1) Sources proposing to locate on Indian reservations in Florida; 
and

[[Page 280]]

    (2) Permits issued by EPA prior to approval of the Florida PSD rule.
[45 FR 52741, Aug. 7, 1980, as amended at 46 FR 17020, Mar. 17, 1981; 48 
FR 52716, Nov. 22, 1983]



Sec. 52.532  Extensions.

    (a) The Administrator hereby extends for 18 months (until July 1, 
1980) the statutory timetable for submittal of Florida's plans to attain 
and maintain the secondary ambient standard for particulate matter in 
the Jacksonville and Tampa nonattainment areas (40 CFR 81.310).
[45 FR 2033, Jan. 10, 1980; 45 FR 28112, Apr. 28, 1980]



Sec. 52.533  Source surveillance.

    The plan lacks test methods for several source categories. As 
required by Sec. 52.12(c)(1) of this part, EPA test methods (found at 40 
CFR part 60) will be used by EPA to determine compliance with the 
following emission limiting standards:
    (a) Particulate emissions from citrus plants controlled by a 
scrubber and subject to the process weight table (submitted as 17-
2.05(2) and reformatted as 17-2.610(1)1.a).
    (b) TRS emissions from recovery furnaces at kraft pulp mills 
(submitted as 17-2.05(6)D and reformatted as 17-2.600(4)1).
    (c) Sulfur dioxide emissions from fossil fuel steam sources 
(submitted as 17-2.05(6)E and reformatted as 17-2.600 (5) and (6)).
    (d) Emissions from portland cement plants (submitted as 17-2.05(6)F 
and reformatted as 17-2.600(7)).
    (e) Particulate and visible emissions from carbonaceous fuel burning 
equipment (submitted as 17-2.05(6)I and reformatted as 17-2.600(10)).
[47 FR 32116, July 26, 1982]



Sec. 52.534  Visibility protection.

    (a) The requirements of section 169A of the Clean Air Act are not 
met because the plan does not include approvable procedures meeting the 
requirements of 40 CFR 51.305 and 51.307 for protection of visibility in 
mandatory Class I Federal areas.
    (b) Regulations for visibility new source review. The provisions of 
Sec. 52.28 are hereby incorporated and made part of the applicable plan 
for the State of Florida.
[51 FR 5505, Feb. 13, 1986]



                           Subpart L--Georgia



Sec. 52.570  Identification of plan.

    (a) Title of plan: ``Implementation Plan for Attainment of State and 
National Ambient Air Standards.''
    (b) The plan was officially submitted on January 27, 1972.
    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) Revisions to paragraph (a)(2) of Code Chapter 88-9 submitted on 
March 28, 1972, by the Assistant Attorney General.
    (2) Certification of public hearing submitted on February 14, 1972, 
by the Georgia Department of Health.
    (3) Miscellaneous non-regulatory additions to the plan submitted on 
March 9, 1972, by the Georgia Department of Health.
    (4) Clarifying comments on the plan submitted on May 5, 1972, by the 
Georgia Department of Health.
    (5) Certification of public hearing and miscellaneous additions to 
Chapter 391-3-1, Sections .02(2)(d), .02(2)(q), .02(2)(r) and .02(6) 
submitted on July 31, 1972, by the Governor.
    (6) Amendments concerning operating permits, Section 391-3-1-.03, 
submitted on March 20, 1974, by the Georgia Department of Natural 
Resources.
    (7) AQMA identification material submitted on May 17, 1974, by the 
Georgia Department of Natural Resources.
    (8) Revisions to Sections 391-3-1-02(2)(a) and 391-3-1-.02(2)(g) and 
revocation of Section 391-3-1-02(2)(i) submitted on July 23, 1974, by 
the Georgia Department of Natural Resources.
    (9) Compliance schedules submitted on August 2, 1974, by the Georgia 
Department of Natural Resources.
    (10) Temporary operating permits submitted as compliance schedules 
on October 8, 1974, by the Georgia Department of Natural Resources.
    (11) Temporary operating permits submitted as compliance schedules 
on November 7, 1974, by the Georgia Department of Natural Resources.

[[Page 281]]

    (12) Compliance schedules submitted on January 23, 1975, by the 
Georgia Department of Natural Resources.
    (13) AQMA identification material submitted on March 10, 1975, by 
the Georgia Department of Natural Resources.
    (14) Permit to operate for Georgia Power Company's Plant Atkinson 
submitted on May 22, 1975, by the Georgia Department of Natural 
Resources.
    (15) Deletion of Section 391-3-1-.02(2)(m), the last sentence in 
Section 391-3-1-.03(2)(c) and the last sentence in Section 391-3-
1-.03(3) submitted on June 30, 1975, by the Georgia Department of 
Natural Resources.
    (16) Miscellaneous plan revisions, submitted on December 16, 1975, 
by the Georgia Department of Natural Resources.
    (17) 1979 Implementation plan revisions for nonattainment areas for 
ozone, total suspended particulates, and carbon monoxide, submitted on 
January 17, March 9, 16, 20, June 29, December 27, 1979 and April 8, 
1980, by the Georgia Department of Natural Resources.
    (18) Order for Georgia Power Company's Plant Bowen, Units 1 and 2, 
Taylorsville, submitted on May 16, 1979, by the Georgia Department of 
Natural Resources.
    (19) Miscellaneous implementation plan revisions, submitted on March 
9, 1979, by the Georgia Department of Natural Resources.
    (20) Alternate VOC compliance schedules for Ford and General Motors 
plants in the Atlanta area, submitted on April 14, 1980 by the Georgia 
Department of Natural Resources.
    (21) Order for Georgia Power Company's Plant Harllee Branch, Unit 3 
and 4 submitted on May 13, 1980, by the Georgia Department of Natural 
Resources.
    (22) Air quality surveillance plan submitted on January 29, 1980, by 
the Georgia Department of Natural Resources.
    (23) Permit revision affecting the allowable particulate emission 
rates from the No. 6 Recovery Boiler, No. 3 Power Boiler and No. 5 Smelt 
Dissolving Tank at the ITT Rayonier, Inc. in Jesup, Georgia submitted on 
December 18, 1980, by the Georgia Department of Natural Resources.
    (24) Order on Units 1 and 2 of Georgia Power Company's Plant Bowen 
submitted on December 20, 1980, by the Georgia Department of Natural 
Resources.
    (25) Georgia lead SIP submitted on December 18, 1980, by the Georgia 
Department of Natural Resources.
    (26) Prevention of significant deterioration SIP, submitted on 
December 18, 1980, by the Georgia Department of Natural Resources.
    (27) A modified permit submitted on December 22, 1981, by the 
Georgia Department of Natural Resources which imposes special reporting 
and opacity limitations on Union Camp Corporation's Power Boilers 11 and 
12 in Savannah, Georgia.
    (28) Set II VOC regulations, submitted on December 18, 1980, by the 
Georgia Department of Natural Resources.
    (29) Alternative VOC compliance schedules for three sources in the 
Atlanta area (St. Regis Paper Co., Printpack, Inc., and American Can 
Co.), submitted on December 18, 1980, and May 7, 1981, by the Georgia 
Department of Natural Resources.
    (30) Revisions to the Part D plan for the Atlanta CO nonattainment 
area, submitted on July 30, 1982, by the Georgia Department of Natural 
Resources.
    (31) Bubble permit for Blue Bird Body Company in Fort Valley, 
submitted on January 27, 1984, by the Georgia Department of Natural 
Resources.
    (32) Visibility new source review regulations and visibility 
monitoring strategy were submitted to EPA on May 22, 1985, and October 
31, 1985.
    (i) Incorporation by reference.
    (A) Letter of May 22, 1985, from the Georgia Department of Natural 
Resources and new paragraph (2)(uu) of Rule No. 391-3-1-.02, titled 
``Visibility Protection'', adopted by the Georgia Board of Natural 
Resources on May 1, 1985.
    (ii) Additional material.
    (A) Narrative SIP, titled ``Georgia's Plan for Visibility Protection 
in Class I Areas'' which includes the State's Visibility Monitoring 
Strategy.
    (B) Letter dated October 31, 1985, from the Georgia Department of 
Natural Resources, providing a schedule for the completion of Georgia's 
Visibility Monitoring Strategy.
    (33) [Revised]

[[Page 282]]

    (34) Revision to Georgia's plan for visibility protection in Class I 
areas entitled ``Visibility SIP'' submitted to EPA on August 31, 1987, 
by the Georgia Environmental Protection Division (GEPD) to satisfy the 
Part 2 visibility requirements.
    (i) Incorporation by reference.
    (A) June 10, 1988, letter from the Georgia Department of Natural 
Resources, and page 5 of the section entitled ``Visibility SIP'' which 
is part of the Georgia plan for visibility protection in Class I areas. 
This page contains the periodic review requirements satisfying 40 CFR 
51.306(c), and was adopted by the Georgia Department of Natural 
Resources on August 31, 1987.
    (ii) Additional material.
    (A) Narrative entitled ``Visibility SIP'', a revision to Georgia's 
plan for visibility protection in Class I areas.
    (35) A revised subsection (2)(c), ``Incinerators,'' of rule 391-3-1-
02 was submitted by the Georgia Department of Natural Resources on May 
22, 1985.
    (i) Incorporation by reference.
    (A) Letter of May 22, 1985, from the Georgia Department of Natural 
Resources and revised subsection (2)(c) of rule 391-3-1-.02, titled 
``Incinerators,'' adopted by the Georgia Board of Natural Resources on 
May 1, 1985.
    (ii) Additional material--none.
    (36) Revised subsections (b) and (d) of rule 391-3-1-.02 (5), ``Open 
Burning,'' were submitted by the Georgia Department of Natural Resources 
on May 22, 1985.
    (i) Incorporation by reference.
    (A) Letter of May 22, 1985, from the Georgia Department of Natural 
Resources and revised subsections (b) and (d) of rule 391-3-1-.02(5), 
entitled ``Open Burning,'' adopted by the Georgia Board of Natural 
Resources on May 1, 1985, to be effective May 27, 1985.
    (ii) Additional material.
    (A) Modeling demonstration, submitted on February 19, 1988, by the 
Georgia Department of Natural Resources.
    (37) Revisions to the VOC regulations, to correct RACT deficiencies; 
Chapter 391-3-1-.01, and .02 of the Georgia Department of Natural 
Resources Rules for Air Quality Control, which was submitted on January 
3, 1991, and April 3, 1991. Change to Chapter 391-3-1-.02(3) to 
reference a new version of the test manual which includes capture 
efficiency protocols, which was submitted on September 30, 1991, and 
November 15, 1991.
    (i) Incorporation by reference.
    (A) The following Rules of the Georgia Department of Natural 
Resources, Chapter 391-3-1, Air Quality Control, became State effective 
on January 9, 1991.

391-3-1-.01(jjj);
391-3-1-.02(2)(a)4.;
391-3-1-.02(2)(t);
391-3-1-.02(2)(u)2.(i) and (iii);
391-3-1-.02(2)(v)2.(i) and (iii);
391-3-1-.02(2)(w)2.(i) and (iii);
391-3-1-.02(2)(x)2.(i), (iii), and (x)3.(v);
391-3-1-.02(2)(y)2.(i) and (iii);
391-3-1-.02(2)(z)2.(i) and (iii);
391-3-1-.02(2)(aa)2.(i) and (iii);
391-3-1-.02(2)(bb)1.(ii);
391-3-1-.02(2)(cc);
391-3-1-.02(2)(ee)1.(iii);
391-3-1-.02(2)(ff)2.(ii)(V) and 3.(iii)(III);
391-3-1-.02(2)(ii)4.(i) and (iii);
391-3-1-.02(2)(jj)2.(i) and (iii);
391-3-1-.02(2)(mm)1.(i), (ii), and (iii);
391-3-1-.02(2)(pp);
391-3-1-.02(2)(qq);
391-3-1-.0292)(rr);
391-3-1-.02(2)(ss);
391-3-1-.02(3)(a);
391-3-1-.02(6)(a)3.

    (B) A revised Rule 391-3-1-.02(3)(a) ``Sampling'' which became State 
effective October 17, 1991.
    (ii) Other material--None.
    (38) State implementation plan for PM10 which was submitted on April 
15, 1988, January 3, 1991, and April 3, 1991, by the Georgia Department 
of Natural Resources.
    (i) Incorporation by reference.
    (A) Revisions to Chapter 391-3-1, ``Air Quality Control'' which 
became State effective April 14, 1988. Rule 391-3-1-.01, 
``Definitions'', mm, yyy, zzz, aaaa; Rule 391-3-1-.02(4)(c), ``Ambient 
Air Standards''; Rule 391-3-1.-02(7), ``Prevention of Significant 
Deterioration of Air Quality''.
    (B) Revisions to Rule 391-3-1-.02(4)(c), ``PM10'', which became 
State effective January 9, 1991.
    (ii) Other material.
    (A) April 15, 1988, January 3, 1991, and April 3, 1991, letters from 
the Georgia Department of Natural Resources.

[[Page 283]]

    (39) On December 15, 1986, and November 13, 1992, the Georgia 
Department of Natural Resources, Environmental Protection Division 
submitted regulations for Part D New Source Review.
    (i) Incorporation by reference. Revisions to the following Rules of 
Georgia Department of Natural Resources, Environmental Protection 
Division, effective November 22, 1992:
    (A) 391-3-1-.01 introductory paragraph
    (B) 391-3-1-.03(8)(c)
    (ii) Other material. Letter dated February 28, 1989, from the 
Georgia Department of Natural Resources, page 3 regarding change in 
operation of a source.
    (40) Revisions to include NO2 increment requirements in 
the PSD regulations, Chapter 391-3-.02(7) of the Georgia Department of 
Natural Resources Administrative Code which was submitted on January 3, 
1991.
    (i) Incorporation by reference.
    (A) Rule 391-3-1-.02(7) entitled ``Prevention of Significant 
Deterioration of Air Quality'' which became state effective on January 
9, 1991.
    (ii) Other material.
    (A) Letters dated January 3, 1991, and April 3, 1991, from the 
Georgia Department of Natural Resources.
    (B) Letter dated August 6, 1991, from the Georgia Department of 
Natural Resources regarding minimum program elements.
    (41) [Reserved]
    (42) Revisions to the Georgia stack height regulations; Chapter 391-
3-1 of the Georgia Department of Natural Resources Administrative Code 
which were submitted on December 15, 1986, and January 3, 1991.
    (i) Incorporation by reference.
    (A) Rule 391-3-1-.02 (2)(g), which was adopted by the Georgia Dept. 
of Natural Resources on December 3, 1986.
    (B) Rule 391-3-1-.01 (Definitions) to include definitions (bbbb) and 
(cccc) for ``stack'' and ``stack in existence''; and Rule 391-3-1-.02 
(2)(a)4., which were adopted on December 5, 1990 by the Georgia 
Department of Natural Resources, and became State law effective January 
9, 1991.
    (43) The Georgia Environmental Protection Division has submitted 
revisions to the Georgia State Implementation Plan on September 27, 
1995. These revisions address the requirements of section 507 of Title V 
of the Clean Air Act and establish the Small Business Stationary Source 
Technical and Environmental Program.
    (i) Incorporation by reference.
    (A) The submittal of the state of Georgia's Small Business 
Stationary Source Technical and Environmental Compliance Assistance 
Program which was adopted on July 20, 1995.
    (ii) Additional Material. None.
    (44) Revisions to the Georgia State Implementation Plan; Chapter 
391-3-1 and Chapter 391-3-10 of the Georgia Department of Natural 
Resources Administrative Code which were submitted to EPA on November 
13, 1992.
    (i) Incorporation by reference.
    (A) Georgia Department of Natural Resources Air Quality Rules 
submitted by the Georgia Department of Natural Resources, Environmental 
Protection Division for inclusion in the Georgia state implementation 
plan which were adopted on October 28, 1992, are as follows:

391-3-1-.05, 391-3-1-.09, 391-3-1-.10, 391-3-1-.02(2)(zz), 391-3-
1-.02(6)(a)4., 391-3-1-.03(5), 391-3-1-.03(6)(h), 391-3-10.01(d)(e), 
391-3-10-.04(d), 391-3-10-.07(2), 391-3-10-.10(b), 391-3-10-.12, 391-3-
10-.24(11), 391-3-10-.30(1), 391-3-10-.30(2).


    (ii) Other material. None.
    (45)  [Reserved]
    (46) Revisions to minor source permit rules submitted by the Georgia 
Environmental Protection Division on March 15, 1995.
    (i) Incorporation by reference. Revised Rule 391-3-1-.03, 
``Permits'', sections (1), (2), and (12), effective August 17, 1994.
    (ii) Other material. None.
    (47) Chapter 391-3-1-.01, .02(2), and .02(7), of the Georgia 
Department of Natural Resources Rules for Air Quality Control, submitted 
on June 24, 1994, and November 15, 1994. Change to Chapters 391-3-
1-.02(3) and 391-3-1-.02(6) to reference a new version of the Georgia 
Department of Natural Resources Manual of Procedures for Testing and 
Monitoring Sources of Air Pollutants, submitted on November 15, 1994.
    (i) Incorporation by reference.

[[Page 284]]

    (A) The following revised Rules of the Georgia Department of Natural 
Resources, Chapter 391-3-1, Air Quality Control, became State effective 
on June 13, 1994:

391-3-1-.02(2)(hh)(iii);
391-3-1-.02(7);


    (B) The following revised Rules of the Georgia Department of Natural 
Resources, Chapter 391-3-1, Air Quality Control, became State effective 
on November 20, 1994:

391-3-1-.01;
391-3-1-.02(2)(t);
391-3-1-.02(2)(ccc);
391-3-1-.02(2)(eee);
391-3-1-.02(3)(a);
391-3-1-.02(6)(a)2.(v)(I);
391-3-1-.02(6)(a)2.(vii)(I);
391-3-1-.02(6)(a)2.(vii)(II)I.;
391-3-1-.02(6)(b)1.(vi)


    (ii) Other material. None.
    (48) Clean Fuel Fleet program submitted to EPA by the Georgia 
Department of Natural Resources on May 5, 1994.
    (i) Incorporation by reference.
    (A) Addition of Regulations 391-3-21-.01, ``Definitions,'' 391-3-
21-.02, ``Covered Area,'' 391-3-21-.03, ``Covered Fleet Operators,'' 
391-3-21-.04, ``Covered Fleet Vehicles,'' 391-3-21-.05, ``Determination 
of Capable of Being Centrally Fueled,'' 391-3-21.06, ``Purchase 
Requirements,'' 391-3-21.07, ``Emission Standards,'' 391-3-21.08, 
``Credit Program,'' 391-3-21.09, ``Transportation Control Exemptions,'' 
391-3-21.10, ``Requirements for Fuel Providers,'' 391-3-21-.11, `` 
Enforcement'' which became effective on May 22, 1994.
    (ii) Other material. None.
    (49)  [Reserved]
    (50) Georgia Enhanced Inspection and Maintenance submitted to EPA by 
the Georgia Department of Natural Resources on March 27, 1996.
    (i) Incorporation by reference.
    (A) Chapter 391-3-20  Enhanced Inspection and Maintenance program 
effective on September 24, 1996.
    (ii) Other material. None.
[37 FR 10859, May 31, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.570, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.571  Classification of regions.

    The Georgia plan was evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                               Pollutant
                                                      ----------------------------------------------------------
              Air quality control region                                                           Photochemical
                                                       Particulate   Sulfur   Nitrogen   Carbon      oxidants
                                                          matter     oxides    dioxide  monoxide  (hydrocarbons)
----------------------------------------------------------------------------------------------------------------
Augusta (Georgia)-Aiken (South Carolina) Interstate..           I         II       III       III           III
Metropolitan Atlanta Intrastate......................           I          I       III       III           III
Chattanooga Interstate...............................           I         II       III       III           III
Columbus (Georgia)-Phenix City (Alabama) Interstate..           I        III       III       III           III
Central Georgia Intrastate...........................           I          I       III       III           III
Jacksonville (Florida)-Brunswick (Georgia) Interstate           I         II       III       III             I
Northeast Georgia Intrastate.........................          II        III       III       III           III
Savannah (Georgia)-Beaufort (South Carolina)
 Interstate..........................................           I          I       III       III           III
Southwest Georgia Intrastate.........................          II         II       III       III           III
----------------------------------------------------------------------------------------------------------------

[37 FR 10859, May 31, 1972, as amended at 39 FR 16346, May 8, 1974]



Sec. 52.572  Approval status.

    With the exceptions set forth in this subpart, the Administrator 
approves Georgia's plans for the attainment and maintenance of the 
national standards under section 110 of the Clean Air Act. Furthermore, 
the Administrator finds the plans satisfy all requirements of Part D, 
Title I, of the Clean Air Act as amended in 1977, except as noted below.
[44 FR 54050, Sept. 18, 1979]



Sec. 52.573  Control strategy: General.

    The generic rules and procedures for emission trades (bubbles), 
submitted on

[[Page 285]]

October 27, 1982, by the Georgia Department of Natural Resources, are 
disapproved because they do not meet the requirements of the Clean Air 
Act.
[49 FR 44464, Nov. 7, 1984]



Sec. 52.574--52.575  [Reserved]



Sec. 52.576  Compliance schedules.

    (a) [Reserved]
    (b) The extended compliance schedule for the General Motors Lakewood 
Assembly Plant submitted on July 30, 1982, is disapproved because the 
State has failed to show that the schedule would not interfere with the 
attainment of the ozone standard in the Atlanta nonattainment area.
[40 FR 3413, Jan. 22, 1975, as amended at 40 FR 18432, Apr. 28, 1975; 40 
FR 42352, Sept. 12, 1975; 51 FR 3778, Jan. 30, 1986; 51 FR 40675, 40676, 
Nov. 7, 1986; 54 FR 25258, June 14, 1989]



Sec. 52.577  [Reserved]



Sec. 52.578  Control Strategy: Sulfur oxides and particulate matter.

    In a letter dated March 26, 1987, the Georgia Department of Natural 
Resources certified that no emission limits in the State's plan are 
based on dispersion techniques not permitted by EPA's stack height 
rules. This certification does not apply to Georgia Power plants; 
Hammond (Coosa), McDonough (Smyrna), Arkwright (Macon), Branch 
(Milledgeville), Wansley (Roopville), Scherer (Juliette), and Yates 
(Newnan), Savannah Electric Plants McIntosh (Rincon) and Port Wentworth 
(Port Wentworth); Inland (Rome); Buckeye Cellulose (Oglethorpe); Georgia 
Kraft (Macon), Union Camp (Savannah); and Stone Container (Savannah).
[54 FR 40002, Sept. 29, 1989]



Sec. 52.579  Economic feasibility considerations.

    Section 88-906(h), (i), (k), (o) and (q) of the Georgia Code is 
disapproved, since consideration of economic feasibility could, in some 
cases, conflict, with the requirements of the Act that primary standards 
be attained as expeditiously as practicable, but in no case later than 
July 1975.
[39 FR 34536, Sept. 26, 1974]



Sec. 52.580  [Reserved]



Sec. 52.581  Significant deterioration of air quality.

    (a) All applications and other information required pursuant to 
Sec. 52.21 of this part from sources located in the State of Georgia 
shall be submitted to the Environmental Protection Division, Georgia 
Department of Natural Resources, 270 Washington Street, S.W., Atlanta, 
Georgia 30334, instead of the EPA Region IV office.
    (b) A letter of commitment concerning the incorporation of EPA's 
revised modeling guidelines for PSD into the Georgia regulations was 
submitted to EPA on May 11, 1987, by the Georgia Department of Natural 
Resources.
[41 FR 24885, June 21, 1976, as amended at 47 FR 6018, Feb. 10, l982; 52 
FR 32918, Sept. 1, 1987]



Sec. 52.582  Control strategy: Ozone.

    (a) Approval--The Administrator approves the incorporation of the 
photochemical assessment ambient monitoring system submitted by Georgia 
on November 8, 1993, into the Georgia State Implementation Plan. This 
submittal satisfies 40 CFR 58.20(f) which requires the State to provide 
for the establishment and maintenance of photochemical assessment 
monitoring stations (PAMS).
    (b) On August 29, 1997, Harold F. Reheis, Director, Georgia 
Department of Natural Resources submitted to John Hankinson, Regional 
Administrator, United States Environmental Protection Agency Region IV, 
a State Implementation Plan revision including the following 
transportation control measures.
    (1) HOV Lane--This project referred to as AR 073B is the addition of 
HOV lanes on I-85 from Chamblee-Tucker Road to State Route 316.
    (2) Ridershare Program--This project is referred to as AR-220 and is 
a lump sum eligible to all colleges and universities with the 10 county 
ARC region.
    (3) Transportation Management Associations--Referred to as project 
AR 221 is to set up a ``pot'' of funds set aside specially to assist in 
the development of transportation management associations and start-up 
ridershare services in the areas that are considered to be

[[Page 286]]

highly congested throughout the Region.
    (4) MARTA Transit Incentives Program--This project is referred to as 
AR-231.
    (5) Alternative Fuel Refueling Station/Park and Ride Transportation 
Center--This project is referred to as DO-AR-211.
[59 FR 46178, Sept. 7, 1994, as amended at 63 FR 23390, Apr. 29, 1998; 
63 FR 34302, June 24, 1998]

    Effective Date Note: At 63 FR 34302, June 24, 1998, Sec. 52.582 was 
amended by adding paragraph (b)(5), effective Aug. 10, 1998.



Sec. 52.583  Additional rules and regulations.

    Section 391-3-1-.02(2)(e), Particulate Emissions from Manufacturing 
Processes, is hereby approved only to the extent that it provides for 
the establishment, as permit conditions, of emission limits more 
stringent than those otherwise applicable under the currently approved 
Georgia regulations. Any application of this regulation which would 
result in permit provisions less stringent than those otherwise required 
by the State's regulations must be formally submitted to EPA for prior 
approval as a plan revision pursuant to section 110(a) of the Clean Air 
Act.
[41 FR 35185, Aug. 20, 1976]



                            Subpart M--Hawaii



Sec. 52.620  Identification of plan.

    (a) Title of plan: ``State of Hawaii Air Pollution Control 
Implementation Plan''.
    (b) The plan was officially submitted on January 28, 1972.
    (1) Previously approved on May 31, 1972 and now deleted without 
replacement chapter 43, section 7.
    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) Certification that the plan was adopted submitted on April 4, 
1972, by the Department of Health.
    (2) Telegram and letters (Non-regulatory) clarifying the plan 
submitted on May 8, 1972, by the Governor.
    (3) Telegram (Non-regulatory) clarifying the particulate matter 
control strategy submitted on May 22, 1972, by the Governor.
    (4) Letter (Non-regulatory) clarifying disapproval of the plan 
submitted on June 15, 1972, by the Governor.
    (5) Revised regulations (in their entirety) for the State of Hawaii 
submitted on November 21, 1972, by the Governor.
    (6) Regulations establishing a permit system for agricultural 
burning submitted on May 15, 1973, by the Governor.
    (7) Compliance schedule submitted on July 27, 1973, by the Governor.
    (8) 18-month extension plan for particulate matter submitted on 
August 15, 1973, by the Governor.
    (9) Date for attainment of the national ambient air quality 
standards for particulate matter submitted on April 25, 1974, by the 
Governor.
    (10) Previously approved on April 23, 1979 and now deleted without 
replacement: A variance to the Hawaii Public Health Regulations, chapter 
43, section 7(b)(5) submitted on September 12, 1978, by the Governor.
    (11) A variance to the Hawaii Public Health Regulations, Chapter 43, 
Section 7(b)(5) submitted on February 22, 1979 by the Governor.
    (12) The following amendments to the plan were submitted on August 
21, 1980, by the Governor.
    (i) XII. Air Quality Surveillance Network.
    (13) A variance to the Hawaii Public Health Regulations, Chapter 43, 
section 8 (b)(1) submitted on November 25, 1980 by the Governor.
    (14) Previously approved on September 30, 1982 and now deleted 
without replacement: A variance of the Hawaii Public Health Regulations, 
chapter 43, section 8(b)(1) submitted on April 6, 1982, by the Governor.
    (15) Hawaii State Lead SIP Revision submitted on October 29, 1982, 
by the State.
    (16) The following amendments to the plan were submitted on December 
20, 1982 by the State.
    (i) Title 11--Department of Health, Chapter 60, Air Pollution 
Control.
    (A) Amended sections 11-60-01 thru 11-60-29, 11-60-35 thru 11-60-38.

[[Page 287]]

    (B) Previously approved on August 18, 1983 and now deleted without 
replacement section 11-60-36.
[37 FR 10861, May 31, 1972, as amended at 41 FR 8959, Mar. 2, 1976; 44 
FR 23828, Apr. 23, 1979; 44 FR 46274, Aug. 7, 1979; 46 FR 40513, Aug. 
10, 1981; 47 FR 3111, Jan. 22, 1982; 48 FR 37403, Aug. 18, 1983; 62 FR 
34648, June 27, 1997]



Sec. 52.621  Classification of regions.

    The Hawaii plan was evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                               Pollutant
                                                      ----------------------------------------------------------
              Air quality control region                                                           Photochemical
                                                       Particulate   Sulfur   Nitrogen   Carbon      oxidants
                                                          matter     oxides    dioxide  monoxide  (hydrocarbons)
----------------------------------------------------------------------------------------------------------------
State of Hawaii......................................          II        III       III       III           III
----------------------------------------------------------------------------------------------------------------

[37 FR 10860, May 31, 1972]



Sec. 52.622  [Reserved]



Sec. 52.623  Approval status.

    With the exceptions set forth in this subpart, the Administrator 
approves Hawaii's plan for attainment and maintenance of the national 
standards. The State included various provisions in its plan to provide 
for the attainment of State ambient air quality standards. As described 
in the Governor's letters of January 28, May 8, and May 22, 1972, these 
provisions were included for information purposes only and were not to 
be considered a part of the plan to implement national standards. 
Accordingly, these additional provisions are not considered a part of 
the applicable plan.
[37 FR 10861, May 31, 1972, as amended at 38 FR 12712, May 14, 1973; 39 
FR 7280, Feb. 25, 1974]



Sec. 52.624  General requirements.

    (a) The requirements of Sec. 51.116(c) of this chapter are not met 
since the legal authority to provide for public availability of emission 
data is inadequate.
    (b) Regulation for public availability of emission data. (1) Any 
person who cannot obtain emission data from the Agency responsible for 
making emission data available to the public, as specified in the 
applicable plan, concerning emissions from any source subject to 
emission limitations which are part of the approved plan may request 
that the appropriate Regional Administrator obtain and make public such 
data. Within 30 days after receipt of any such written request, the 
Regional Administrator shall require the owner or operator of any such 
source to submit information within 30 days on the nature and amounts of 
emissions from such source and any other information as may be deemed 
necessary by the Regional Administrator to determine whether such source 
is in compliance with applicable emission limitations or other control 
measures that are part of the applicable plan.
    (2) Commencing after the initial notification by the Regional 
Administrator pursuant to paragraph (b)(1) of this section, the owner or 
operator of the source shall maintain records of the nature and amounts 
of emissions from such source and any other information as may be deemed 
necessary by the Regional Administrator to determine whether such source 
is in compliance with applicable emission limitations or other control 
measures that are part of the plan. The information recorded shall be 
summarized and reported to the Regional Administrator, on forms 
furnished by the Regional Administrator, and shall be submitted within 
45 days after the end of the reporting period. Reporting periods are 
January 1 to June 30 and July 1 to December 31.
    (3) Information recorded by the owner or operator and copies of this 
summarizing report submitted to the Regional Administrator shall be 
retained by the owner or operator for 2

[[Page 288]]

years after the date on which the pertinent report is submitted.
    (4) Emission data obtained from owners or operators of stationary 
sources will be correlated with applicable emission limitations and 
other control measures that are part of the applicable plan and will be 
available at the appropriate regional office and at other locations in 
the state designated by the Regional Administrator.
[39 FR 34536, Sept. 26, 1974, as amended at 40 FR 55329, Nov. 28, 1975; 
51 FR 40676, Nov. 7, 1986]



Sec. 52.625  Legal authority.

    (a) The requirements of Sec. 51.230(f) of this chapter are not met, 
since sections 322-64(5) and 322-66 of the Hawaii Revised Statutes 
could, in some circumstances, prohibit the disclosure of emission data 
to the public. Therefore, sections 322-64(5) and 322-66 are disapproved.
[39 FR 34536, Sept. 26, 1974, as amended at 51 FR 40676, Nov. 7, 1986]



Sec. 52.626  Compliance schedules.

    (a) [Reserved]
    (b) The compliance schedules for the sources identified below are 
disapproved as not meeting the requirements of Subpart N of this 
chapter. The regulations cited are air pollution control regulations of 
the State.

----------------------------------------------------------------------------------------------------------------
                                                                  Regulation sections
                Source                         Location                 involved             Date of adoption
----------------------------------------------------------------------------------------------------------------
Nanakuli Paving . Rock Co., Ltd......  Molokai................  8, 13..................  7/27/73.
Kohala Corp..........................  Halaula................  8, 12..................      Do.
----------------------------------------------------------------------------------------------------------------

[39 FR 16348, May 8, 1974, as amended at 51 FR 40676, Nov. 7, 1986; 54 
FR 25258, June 14, 1989]



Sec. 52.627--52.631  [Reserved]



Sec. 52.632  Significant deterioration of air quality.

    (a) The requirements of sections 160 through 165 of the Clean Air 
Act are not met, since the plan does not include approvable procedures 
for preventing the significant deterioration of air quality.
    (b) Regulations for preventing significant deterioration of air 
quality. The provisions of Sec. 52.21(b) through (w) are hereby 
incorporated and made a part of the applicable state plan for the State 
of Hawaii.
[43 FR 26410, June 19, 1978, as amended at 45 FR 52741, Aug. 7, 1980]



Sec. 52.633  Visibility protection.

    (a) The requirements of section 169A of the Clean Air Act are not 
met, because the plan does not include approvable procedures for 
protection of visibility in mandatory Class I Federal areas.
    (b) Regulations for visibility monitoring and new source review. The 
provisions of Secs. 52.26, 52.27 and 52.28, are hereby incorporated and 
made part of the applicable plan for the State of Hawaii.
    (c) Long-term strategy. The provisions of Sec. 52.29 are hereby 
incorporated and made part of the applicable plan for the State of 
Hawaii.
[50 FR 28553, July 12, 1985, as amended at 52 FR 45137, Nov. 24, 1987]



Sec. 52.634  Particulate matter (PM-10) Group III SIP.

    (a) On September 14, 1988, the Governor of Hawaii submitted a 
revision to the State Implementation Plan (SIP) for implementing the 
required monitoring activities and other tasks necessary to satisfy the 
requirements of the PM-10 Group III SIP.
    (b) The Hawaii Department of Health has committed to meet the 
ongoing requirements for PM-10 Group III areas.
[55 FR 18110, May 1, 1990]



                            Subpart N--Idaho



Sec. 52.670  Identification of plan.

    (a) Title of plan: ``Idaho Air Quality Implementation Plan.''
    (b) The plan was officially submitted on January 31, 1972.
    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) Miscellaneous additions (compliance schedules and non-regulatory 
provisions) to the plan submitted on February 23, 1972, by the Idaho Air 
Pollution Control Commission.

[[Page 289]]

    (2) Request for delegation of legal authority submitted on March 2, 
1972, by the Governor.
    (3) Compliance schedules submitted on April 12, 1972, by the 
Governor.
    (4) Request for an 18-month extension for particulate matter in all 
AQCR's submitted on May 5, 1972, by the Governor.
    (5) Miscellaneous additions (Non-regulatory) to the plan submitted 
on May 26, 1972, by the Idaho Air Pollution Control Commission.
    (6) Appendices D and E of the plan submitted on June 9, 1972, by the 
Governor.
    (7) Revisions to the Rules and Regulations for the Control of Air 
Pollution in Idaho submitted on February 15, 1973, by the Governor.
    (8) Compliance schedules submitted on July 23, 1973, by the 
Governor.
    (9) Amendment to Chapter IX of the plan to provide for review of 
indirect sources and a new Chapter XIV which sets forth the control 
strategy for attaining secondary particulate matter standards on October 
16, 1973, by the Governor.
    (10) Revisions to 1972 Session Laws, Chapter 347; 1973 Session Laws, 
Chapter 87, 136, 137, 138, 139, and 143; Chapters 18 and 52, Idaho Code; 
and the accompanying Attorney General's opinion submitted August 15, 
1973, by the Governor.
    (11) A new section 4 of Regulation A (General Provisions) and 
revised Regulation T (Air Pollution Sources Permits) of the Rules and 
Regulations for the Control of Air Pollution in Idaho (Chapter VII of 
the plan), an addition to Chapter XI of the plan to include 
administrative procedures for indirect source review, and compliance 
schedules submitted on July 1, 1974, by the Governor.
    (12) Air quality maintenance area designation submitted on June 11, 
1974, by the Idaho Department of Environmental and Community Services.
    (13) An amendment to Regulation C (Ambient Air Quality Standards) 
and Regulation S (Control of Sulfur Oxide Emissions from Combined Lead/
Zinc Smelters) of the Rules and Regulations for the Control of Air 
Pollution in Idaho and revisions to Chapter IV and Appendix F of the 
Implementation Plan submitted on January 10, 1975, by the Governor.
    (14) Revised sections 2 and 6 of Regulation A (General Provisions) 
of the Rules and Regulations for the Control of Air Pollution in Idaho 
submitted on January 24, 1975, by the Governor.
    (15) Consent Order for Beker Industries submitted on July 28, 1975 
by the Governor.
    (16) On January 15, 1980 the Governor submitted the transportation 
portion of the Boise-Ada County carbon monoxide plan.
    (17) On July 1, 1980 the Governor submitted a SIP revision 
containing a variance from the indirect source regulation for an urban 
renewal project located in downtown Boise, as well as an adjustment to 
the TCP which had been submitted to EPA in January 1980.
    (18) On February 14, 1980 the State of Idaho Department of Health 
and Welfare submitted a plan revision to meet the requirements of Air 
Quality Monitoring 40 CFR part 58, subpart C, Sec. 58.20.
    (19) Revisions to the ``Implementation Plan for the Control of Air 
Pollution in the State of Idaho'' submitted by the Governor of Idaho on 
January 15, 1980: Chapter I ``Introduction;'' Chapter II ``General 
Administration;'' Chapter III ``Emissions Inventory;'' Chapter IV ``Air 
Quality Monitoring;'' Chapter V ``Source Surveillance;'' Chapter VI 
``Emergency Episode Plan;'' Chapter VII ``Approval Procedures for New 
and Modified Sources;'' Chapter VIII ``Non-Attainment Area Plans;'' 
Chapter VIII-a ``Silver Valley Non-Attainment Plan;'' Chapter VIII-e 
``Soda Springs Non-Attainment Plan;'' Appendix A.2 Legal Authority 
(Section 39-100, Idaho Code); Appendix A.3, Title I, Chapter I, Rules 
and Regulations for the Control of Air Pollution in Idaho, except 
indirect source review provisions (1-1002.37, 1-1002.76 and 1-1004), 
variance provisions (1-1007 and 1-1904) and ``Sulfur Dioxide Emission 
Limitations for Combined Zinc and Lead Smelters'' (1-1851 through 1-
1868); Appendix B ``Emission Inventory, Ada County Carbon Monoxide Non-
Attainment Area;'' Appendix G ``Permits--Silver Valley'' (six permits); 
and Appendix K ``Permits--Soda Springs'' (four permits).

[[Page 290]]

    (20) Chapter VIII-b ``Lewiston Non-Attainment Plan'' submitted by 
the Governor of Idaho on January 15, 1980. On December 4, 1980, the 
Governor submitted revised pages 31-39, an operating permit for a kraft 
pulp and paper mill (Appendix H.1), operating permits for two grain 
loading terminals (Appendices H.3 and H.4), and an operating permit for 
an asphalt plant (Appendix H.5). On February 5, 1981 the Governor 
further revised the nonattainment area plan by submitting a permit for a 
wood products operation (Appendix H.2).
    (21) Chapter VIII-d ``Pocatello TSP Non-Attainment Plan'' submitted 
by the Governor of Idaho on March 7, 1980. This submittal included 
operating permits for an elemental phosphorus plant (Appendix J.1), a 
phosphate fertilizer manufacturing plant (Appendix J.2), and a Portland 
cement plant (Appendix J.3). On February 5, 1981, the Governor submitted 
a revised Chapter VIII-d.
    (22) On February 3, 1984 the State of Idaho Department of Health and 
Welfare submitted a revision to add a lead maintenance strategy to the 
Idaho Implementation Plan.
    (23) On May 29, 1984, the State of Idaho Department of Health and 
Welfare submitted the Boise-Ada County carbon monoxide attainment plan 
as an official State Implementation Plan revision. The submittal was 
then supplemented on January 3, 1985.
    (24) A revised Chapter VII Approval Procedures for New and Modified 
Facilities; revised sections 1-1002, 1-1012, 1-1013, 1-1014, and 1-1101 
of Appendix A. 3 ``Title 1, Chapter 1, Rules and Regulations for the 
Control of Air Pollution in Idaho Manual;'' and the repeal of sections 
1-1003, 1-1102 through 1-1112, and 1-1900 through 1-1906 of Appendix A. 
3 ``Title 1, Chapter 1, Rules and Regulations for the Control of Air 
Pollution in Idaho Manual;'' of the Implementation Plan for the Control 
of Air Pollution in the State of Idaho, submitted by the Director of the 
State of Idaho Department of Health and Welfare on April 19, 1985. 
(Sections 1-1003, 1-1102 through 1-1112, and 1-1900 through 1-1906 of 
Appendix A. 3 ``Title 1, Chapter 1, Rules and Regulations for the 
Control of Air Pollution in Idaho Manual'' were previously approved by 
EPA at 40 CFR 52.670(c)(19).) An April 3, 1986, commitment letter from 
the Director of the State of Idaho Department of Health and Welfare 
regarding stack height provisions.
    (i) Incorporation by reference. (A) Revised sections 1-1002, 1-1012, 
1-1013, 1-1014, and 1-1101 of Appendix A. 3, ``Title 1, Chapter 1, Rules 
and Regulations for the Control of Air Pollution in Idaho Manual'' of 
the Implementation Plan for the Control of Air Pollution in the State of 
Idaho, as adopted by the Idaho Board of Health and Welfare on November 
1, 1984. An April 3, 1986, commitment letter from the Director of the 
State of Idaho Department of Health and Welfare regarding stack height 
provisions.
    (ii) Other materials. (A) Revised Chapter VII Approval Procedures 
for New and Modified Facilities of the Implementation Plan for the 
Control of Air Pollution in the State of Idaho, submitted by the 
Director of the Idaho Department of Health and Welfare on April 19, 
1985. (This revised chapter replaces an earlier version which was 
approved by EPA and incorporated by reference at 40 CFR 52.670(c)(19).)
    (B) Sections 1-1003, 1-1102 through 1-1112, and 1-1900 through 1-
1906 of Appendix A. 3 ``Title 1, Chapter 1, Rules and Regulations for 
the Control of Air Pollution in Idaho,'' of the Implementation Plan for 
the Control of Air Pollution in the State of Idaho, repealed by the 
Idaho Board of Health and Welfare on November 1, 1984. (These sections, 
noted as repealed, replace the earlier versions which were approved by 
EPA and incorporated by reference at 40 CFR 52.670(c)(19).)
    (25) On March 27, 1987, the State of Idaho Department of Health and 
Welfare submitted revised rules regulating the use of stack heights and 
dispersion techniques (section 16.01.1002.94 and section 16.01.1014) as 
revisions to the Idaho state implementation plan. Additional revisions 
included clarifications to section 16.01.1009 (Total Compliance), and 
section 16.01.1201.03 (Visible Emissions-Exception).
    (i) Incorporation by reference.
    (A) March 27, 1987 letter from the State of Idaho Department of 
Health and Welfare to EPA, Region 10.

[[Page 291]]

    (B) Section 16.01.1002.94 (Stack), section 16.01.1014 (Stack Heights 
and Dispersion Techniques), section 16.01.1009 (Total Compliance) and 
section 16.01.1201.03 (Visible Emissions-Exception) adopted by the State 
of Idaho Department of Health and Welfare on February 11, 1987.
    (26) On June 15, 1990, the Administrator of the Idaho Department of 
Health and Welfare submitted amendments to State of Idaho's Rules and 
Regulations for the Control of Air Pollution in Idaho Manual as 
revisions to the Idaho state implementation plan as follows: Idaho 
Administrative Procedures Act, Section 16.01.01002 Definitions, Section 
16.01.01012 Procedures and Requirements for Permits to Construct and 
Operating Permits, and Section 16.01.01101 Air Quality Standards and 
Area Classification.
    (27) On September 4, 1992, the Administrator of the Idaho Department 
of Health and Welfare submitted a revised and recodified Rules and 
Regulations for the Control of Air Pollution in Idaho Manual (Idaho 
Administrative Procedures Act Sections 16.01.01000 through 16.01.01999) 
as a revision to the Idaho state implementation plan.
    (i) Incorporation by reference.
    (A) June 15, 1990, letter from the Administrator of the Idaho 
Department of Health and Welfare to EPA Region 10 submitting amendments 
to the Idaho state implementation plan.
    (B) September 4, 1992, letter from the Administrator of the Idaho 
Department of Health and Welfare to EPA Region 10 submitting amendments 
to the Idaho state implementation plan.
    (C) Idaho's Rules and Regulations for the Control of Air Pollution 
in Idaho Manual (except for sections IDAPA 16.01.01007 Variances, IDAPA 
16.01.01853 through 16.01.01856 Combined Zinc and Lead Smelters, IDAPA 
16.01.0951 through 16.01.01968 Regulation of Standards of Performance 
for New Stationary Sources, and IDAPA 16.01.01997 Confidentiality of 
Records) as adopted by the Board of the Idaho Department of Health and 
Welfare on July 30, 1992, and effective on August 21, 1992.
    (28) On April 14, 1992, the State of Idaho submitted a revision to 
the SIP for Pinehurst, ID, for the purpose of bringing about the 
attainment of the national ambient air quality standards for particulate 
matter with an aerodynamic diameter less than or equal to a nominal 10 
micrometers. This submittal includes an additional area in Shoshone 
County adjacent to the City of Pinehurst which EPA designated 
nonattainment and moderate for PM-10 on January 20, 1994.
    (i) Incorporation by reference.
    (A) April 7, 1992 letter from Idaho Department of Health and Welfare 
to EPA Region 10 submitting the Pinehurst Particulate Air Quality 
Improvement Plan as a revision to the Implementation Plan for the 
Control of Air Pollution in the State of Idaho. The plan has been 
adopted in accordance with the authorities and requirements of the 
Federal Clean Air Act and the Idaho Environmental Protection and Health 
Act (Idaho Code section 39-10/et seq).
    (B) SIP revision for Pinehurst Particulate Air Quality Improvement 
Plan, February 5, 1992 (adopted on April 7, 1992).
    (29) On June 29, 1994, the Idaho Department of Health and Welfare 
submitted a CO State Implementation Plan for Northern Ada County, Idaho.
    (i) Incorporation by reference.
    (A) June 29, 1994 letter from Idaho Department of Health and Welfare 
to EPA Region 10 submitting the CO SIP for Northern Ada County, Idaho.
    (B) Minor Revision of the Northern Ada County, Idaho 1984 State 
Implementation Plan for CO, June 1994 (including Ada County Ordinance 
228, City of Boise Ordinance 5273, City of Meridian Ordinance 547, City 
of Garden City Ordinance 558, and City of Eagle Ordinance 177), as 
adopted by the Idaho Department of Health and Welfare on June 28, 1994.
    (30) On January 7, 1994, the Administrator for the Idaho Department 
of Health and Welfare, Division of Environmental Quality, submitted the 
State PROGRAM as a revision to the Idaho SIP.
    (i) Incorporation by reference.
    (A) The January 3, 1994 letter from the Administrator of the Idaho 
Department of Health and Welfare, Division of Environmental Quality, 
submitting the PROGRAM to EPA.
    (B) The State Implementation Plan Revision to Establish a State 
Small

[[Page 292]]

Business Stationary Source Technical and Environmental Compliance 
Assistance Program (which includes the text of Idaho Code 39-118E, Small 
Business Assistance, signed into law Senate bill 1236 by Idaho Governor, 
Cecil D. Andrus, on March 29, 1993), dated December 29, 1993, and 
adopted on January 3, 1994.
    (31) On November 14, 1991, and on December 30, 1994, the Idaho 
Department of Health and Welfare (IDHW) submitted revisions to the Idaho 
State Implementation Plan (SIP) for the Northern Ada County/Boise 
Particulate (PM10) Air Quality Improvement Plan.
    (i) Incorporation by reference.
    (A) November 14, 1991, letter from the IDHW Administrator to the EPA 
Region 10 Regional Administrator submitting a revision to the Idaho SIP 
for the Northern Ada County/Boise Particulate Air Quality Improvement 
Plan; The Northern Ada County Boise Particulate (PM10) Air 
Quality Improvement Plan adopted on November 14, 1991.
    (B) December 30, 1994, letter from the IDHW Administrator to the EPA 
Region 10 Regional Administrator including a revision to the Idaho SIP 
for the Northern Ada County/Boise PM10 Air Quality 
Improvement Plan; Appendix C-1, Supplemental Control Strategy 
Documentation, Northern Ada County/Boise PM10 Air Quality 
Improvement Plan, adopted December 30, 1994, with the following 
attachments: Garden City Ordinances #514 (May 14, 1987), #533 (January 
10, 1989) and #624 (September 13, 1994); Meridian Ordinance #667 (August 
16, 1994); Eagle Ordinance #245 (April 26, 1994); Ada County Ordinance 
#254 (November 3, 1992); and Table Ordinance-1 (December 30, 1994).
[37 FR 10861, May 31, 1972, as amended at 41 FR 8959, Mar. 2, 1976; 41 
FR 23202, June 9, 1976; 45 FR 70261, Oct. 23, 1980; 46 FR 15136, Mar. 4, 
1981; 47 FR 32533, July 28, 1982; 49 FR 18833, May 3, 1984; 50 FR 23811, 
June 6, 1985; 51 FR 22810, June 23, 1986; 53 FR 48540, Dec. 1, 1988; 58 
FR 39447, July 23, 1993; 59 FR 43751, Aug. 25, 1994; 59 FR 47804, Sept. 
19, 1994; 59 FR 61549, Dec. 1, 1994; 60 FR 27893, May 26, 1995; 61 FR 
27023, May 30, 1996]



Sec. 52.671  Classification of regions.

    The Idaho plan was evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                    Pollutants
                                 -------------------------------------------------------------------------------
   Air quality control region        Particulate       Sulfur
                                       matter          oxides     Nitrogen dioxide  Carbon monoxide     Ozone
----------------------------------------------------------------------------------------------------------------
Eastern Idaho Intrastate........  I...............  II..........  III.............  III............  III.
Eastern Washington Northern       I...............  II..........  III.............  III............  III.
 Idaho Interstate (Idaho).
Idaho Intrastate................  I...............  III.........  III.............  III............  III.
Metropolitan Boise Intrastate...  II..............  III.........  III.............  I..............  III.
----------------------------------------------------------------------------------------------------------------

[37 FR 10861, May 31, 1972, as amended at 45 FR 70261, Oct. 23, 1980; 47 
FR 32534, July 28, 1982]



Sec. 52.672  [Reserved]



Sec. 52.673  Approval status.

    With the exceptions set forth in this subpart, the Administrator 
approves Idaho's plan for the attainment and maintenance of the national 
standards.



Sec. 52.674  Legal authority.

    (a) The requirements of Sec. 51.230(f) of this chapter are not met 
since the authority to release emission data to the public could be 
precluded in certain circumstances by section 39-111 of the Idaho Code 
annotated.
    (b) Delegation of Authority: Pursuant to section 114 of the Act, 
Idaho requested a delegation of authority to enable it to collect, 
correlate, and release emission data to the public. The Administrator 
has determined that Idaho is qualified to receive a delegation of the 
authority it requested. Accordingly, the Administrator delegates to 
Idaho his authority under section 114(a) (1) and (2) and section 114(c) 
of the Act, i.e., authority to collect, correlate, and release emission 
data to the public.
[37 FR 10861, May 31, 1972, as amended at 39 FR 41253, Nov. 11, 1974; 51 
FR 40676, Nov. 7, 1986]


[[Page 293]]





Sec. 52.675  Control strategy: Sulfur oxides--Eastern Idaho Intrastate Air Quality Control Region.

    (a)(1) Regulation R of the Rules and Regulations for the Control of 
Air Pollution in Idaho, which is part of the sulfur dioxide 
(SO2) control strategy, is disapproved since it is 
inconsistent with the purposes and provisions of subpart G of this 
chapter. These requirements are not met by Regulation R in that the 
SO2 control strategy contained therein is not adequate for 
the attainment and maintenance of SO2 national ambient air 
quality standards (NAAQS).
    (2) Rules 1-1801 through 1-1804 (Rules for Control of Sulfur Oxide 
Emissions from Sulfuric Acid Plants) of the ``Rules and Regulations for 
the Control of Air Pollution in Idaho'' are inadequate to ensure 
attainment and maintenance of Sulfur Dioxide National Ambient Air 
Quality Standards in the Eastern Idaho Intrastate Air Quality Control 
Region. Special limits have previously been established for certain 
existing acid plants in this Air Quality Control Region 
(Secs. 52.670(c)(15) and 52.675(b)). Therefore, Rules 1-1801 through 1-
1804 are approved except as they apply to existing acid plants with 
approved or promulgated emission limits that are more stringent than the 
limit found in 1-1802.
    (b) Regulation for control of sulfur dioxide (SO2) 
emissions: Sulfuric Acid Plants. (1) The provisions of this paragraph 
shall apply to the owner(s) and operator(s) of The J. R. Simplot 
Company's Minerals and Chemical Division, located in Power County, 
Idaho, in the Eastern Idaho Intrastate Air Quality Control Region.
    (2) The owner(s) and operator(s) of The J. R. Simplot Company 
facility shall utilize best engineering techniques in the operation of 
their plant to prevent fugitive SO losses. Such techniques shall include 
but are not limited to:
    (i) Operating and maintaining all conducts, flues, and stacks in a 
leakfree condition.
    (ii) Operating and maintaining all process equipment and gas 
collection systems in such a fashion that leakage of SO2 
gases will be prevented to the maximum extent possible.
    (3) The owner(s) and operator(s) of The J. R. Simplot Company 
facility shall limit SO2 emissions from their sulfuric acid 
plants per the following:
    (i) The combined SO2 emissions from the designated 100 
and 200 sulfric acid plants shall not exceed 2 kilograms (kg) per metric 
ton (4 pounds per ton) of 100 percent sulfuric acid produced.
    (ii) The SO2 emissions from the designated 300 sulfuric 
acid plant and stack shall not exceed 994 kg per hour (2190 pounds per 
hour).
    (4) (i) The owner(s) and operator(s) of The J. R. Simplot Company 
shall achieve compliance with the requirements specified in paragraphs 
(b)(2) and (b)(3) of this section in accordance with the following 
schedule:
    (A) Advise EPA as to status of contract(s) and construction 
schedules for pollution abatement projects within 30 days of the 
effective date of this regulation.
    (B) Attain final compliance by July 31, 1976.
    (ii) A performance test of the 300 acid plant shall be necessary to 
determine whether compliance has been achieved with the requirements of 
paragraph (b)(3) of this section. Such test must be completed within 15 
days of the final compliance date specified in paragraph (b)(4)(i) of 
this section. Notice must be given to the Administrator at least 10 days 
prior to such a test to afford him an opportunity to have an observer 
present.
    (iii) Within 60 days after achieving the maximum production rate at 
which the 100 and 200 acid plant will be operated, but not later than 
180 days after initial start-up of these plants and at such other times 
as may be required by the Administrator under section 114 of the Clean 
Air Act, the owner(s) and operator(s) of the facility shall conduct 
performance test(s) in accordance with the requirements of 40 CFR 60.8.
    (iv) If the owner(s) and operator(s) of the J. R. Simplot Company 
facility are presently in compliance with the requirements of paragraphs 
(b)(2) and (b)(3) of this section or in compliance with a portion of 
these requirements, such compliance shall be certified to the 
Administrator within 15 days following the date of the publication of

[[Page 294]]

these requirements as a final regulation in the Federal Register. If the 
owner(s) or operator(s) of The J. R. Simplot Company achieve compliance 
prior to July 31, 1976, such compliance shall be certified to the 
Administrator within 15 days of the date of achieving compliance. The 
Administrator may request whatever supporting information he considers 
necessary to determine the validity of the certification.
    (5) (i) By no later than September 30, 1976, the owner(s) and 
operator(s) of The J. R. Simplot Company facility shall install, 
calibrate, maintain and operate measurement system(s) for:
    (A) Continuously monitoring and recording SO2 
concentration rates in each sulfuric acid plant discharge stack per the 
requirements of 40 CFR 60.13 and 60.84.
    (B) Continuously monitoring and recording gas volumetric flow rates 
in the exhaust stack of the designated 300 sulfuric acid plant.
    (ii) By no later than October 30, 1976, and at such other times 
following that date as the Administrator may specify, the SO2 
concentration measurement system(s) and stack gas volumetric flow rate 
system(s) installed and used pursuant to this paragraph shall be 
demonstrated to meet the measurement system performance specifications 
prescribed in 40 CFR 60.13 and Appendix E to this part, respectively. 
The Administrator shall be notified at least 10 days prior to the start 
of this field test period to afford the Administrator the opportunity to 
have an observer present.
    (iii) The sampling point for monitoring the concentration of 
SO2 emissions shall be in the duct at the centroid of the 
cross section of the discharge stack if the cross sectional area is less 
than 4.65 m 2 (50 ft 2) or at a point no closer to 
the wall than 0.91 m (3 ft) if the cross sectional area is 4.65 m 2 
(50 ft 2) or more. The monitor sample point shall be 
representative of the average concentration in the duct.
    (iv) The measurement system(s) shall be maintained, operated and 
calibrated in accordance with the methods prescribed by the 
manufacturers. Records of maintenance and/or calibration shall be kept 
and submitted to the Administrator upon request. These records shall 
clearly show instrument readings before and after such calibration and/
or maintenance.
    (v) The owner(s) and operator(s) of The J. R. Simplot Company 
facility shall maintain a daily record of three hour average emission 
rate measurements for each sulfuric acid plant. Three hour average 
emission rates shall be calculated for each day beginning at midnight. 
For the 100 and 200 acid plants, the calculations shall be in 
conformance with 40 CFR 60.84. For the 300 acid plant, average SO2 
emission rates expressed in kg SO2 per hour shall be 
calculated. The results of these calculations for each month shall be 
submitted to the Administrator within 15 days following the end of each 
month. Such submission shall identify each period of excess emissions 
that occurred and the nature and cause of any malfunction (if known), 
the corrective action taken or preventative measures adopted. The 
records of such measurements including strip charts and other 
appropriate raw data shall be retained for a minimum of two years 
following the date of such measurements.
    (vi) The continuous monitoring and recordkeeping requirements of 
paragraph (b)(5) of this section shall become applicable September 30, 
1976.
    (6)(i) Compliance with the requirements set forth in paragraph 
(b)(3) of this section shall be determined using the emission rates 
measured by the continuous measurement system(s) installed, calibrated, 
maintained and operated in accordance with the requirements of paragraph 
(b)(5) of this section.
    (ii) At the Administrator's discretion, compliance may also be 
determined using the manual source test methods per 40 CFR 60.85 and 
Appendix A to part 60 of this title. Emission rates for each stack shall 
be expressed in units consistent with those in paragraph (b)(3) of this 
section.
    (iii) A violation of the requirements of paragraph (b)(3) of this 
section shall occur whenever the SO2 emission rates 
determined according to paragraph (b)(6)(i) or (b)(6)(ii) of this 
section exceed the corresponding SO2 emission rates specified 
in paragraph (b)(3) of this section.

[[Page 295]]

    (7) The owner(s) and operator(s) of The J. R. Simplot Company 
facility shall by September 30, 1976, install, calibrate, maintain and 
operate a network for continuously monitoring ground level ambient 
SO2 concentrations and wind speed and direction.
    (i) The monitoring network shall consist of at least four ambient 
SO2 monitoring stations and one meteorological station placed 
at locations approved by the Administrator.
    (ii) The SO2 monitoring network shall be consistent with 
automated equivalent methods for measurement of ambient concentrations 
of SO2 as defined in part 53 of this chapter.
    (iii) The monitoring network installed and used pursuant to this 
subparagraph shall be maintained, operated and calibrated in accordance 
with the methods prescribed by the manufacturers. Records of maintenance 
and/or calibration shall be kept and submitted to the Administrator upon 
request. These records shall clearly show instrument readings before and 
after such calibration and/or maintenance.
    (iv) The owner(s) and operator(s) of The J. R. Simplot Company 
facility shall maintain a daily record of all measurements required by 
this subparagraph. Strip charts and other raw data from the monitoring 
network shall be retained for a minimum of two years following the date 
of such measurement.
    (v) The owner(s) and operator(s) of The J. R. Simplot Company shall 
calculate hourly average ambient SO2 concentrations, wind 
speed, and wind direction from each monitoring station and submit such 
values to the Administrator within 15 days following the end of each 
month.
    (vi) The continuous monitoring and recordkeeping requirements of 
paragraph (b)(7) of this section shall become applicable September 30, 
1976 and shall remain applicable until such time as the Administrator 
declares that an adequate ambient air data base has been established, 
which shall be no earlier than at least one calendar year.
    (vii) Within 90 days of the Administrator's declaration of an 
adequate data base, Simplot shall submit to the Administrator a 
technical analysis of the degree of permanent control required on the 
300 acid plant to ensure attainment and maintenance of NAAQS.
    (8) Nothing in paragraph (b) of this section shall be construed to 
relieve the owner(s) and operator(s) of The J. R. Simplot Company to 
comply with any applicable requirements of part 60 of this title. In the 
event of conflicting requirements or interpretations between part 60 of 
this title and this paragraph, the more restrictive interpretation or 
requirement shall apply.
    (9) In the event that measurement systems cannot be installed and 
operational by the date specified in this section, The J. R. Simplot 
Company shall propose the earliest possible date by which such 
requirements can be met. Such proposal shall include adequate 
justification and supporting documentation.
[41 FR 23202, June 9, 1976, as amended at 47 FR 32534, July 28, 1982; 51 
FR 40676, Nov. 7, 1986]



Secs. 52.676--52.678  [Reserved]



Sec. 52.679  Contents of Idaho State Implementation Plan.

  Implementation Plan for the Control of Air Pollution in the State of 
                                  Idaho

Chapter I--Introduction (submitted 1-15-80)
Chapter II--Administration (submitted 1-15-80)
Chapter III--Emissions Inventory (submitted 1-15-80)
Chapter IV--Air Quality Monitoring (submitted 1-15-80, 2-14-80)
Chapter V--Source Surveillance (submitted 1-15-80)
Chapter VI--Emergency Episode Plan (submitted 1-15-80)
Chapter VII--Approval Procedures for New and Modified Facilities 
          (submitted 4-19-85)
Chapter VIII--Non-Attainment Area Plan
    VIII-a--Silver Valley Nonattainment Plan (submitted 1-15-80)
    VIII-b--Lewiston Nonattainment Plan (submitted 1-15-80, 12-4-80)
    VIII-c--Transportation Control Plan for the carbon monoxide of Ada 
County (submitted 5-24-84, 1-3-85, 3-25-85)
    VIII-d--Pocatello TSP Nonattainment Plan (submitted 3-7-80, 2-5-81)
    VIII-e--Soda Springs Nonattainment Plan (submitted 1-15-80)
Chapter IX--Reserved

[[Page 296]]

Chapter X--Plan for Maintenance of National Ambient Air Quality 
          Standards for Lead (submitted 2-3-84)
Appendix A--Legal Authority and Other General Administrative Matters 
          (submitted 1-15-80)
Appendix A.2--Section 39-100, Idaho Code (submitted 1-15-80)
Appendix A.3--Title 1, Chapter 1, Rules and Regulations for Control of 
          Air Pollution in Idaho Manual (submitted 1-15-80, 4-19-85, 6-
          15-90, 8-21-92)
    01.01000. Legal Authority (6-28-78)
    01.01001. Policy (6-28-78)
    01.01002. Title (12-31-91)
    01.01003. Definitions
    01.01003,01. Act (4-1-72)
    01.01003,02. Actual Emissions (11-1-84)
    01.01003,03. Adverse Effect on Visibility (11-1-84)
    01.01003,04. Agricultural Field (3-12-85)
    01.01003,05. Air Contaminant (11-1-84)
    01.01003,06. Air Pollution (1-24-69)
    01.01003,07. Air Quality (4-1-72)
    01.01003,08. Air Quality Criterion (4-1-72)
    01.01003,09. Allowable Emissions (11-1-84)
    01.01003,10. Ambient Air (11-1-84)
    01.01003,11. Ambient Air Quality Violation (8-11-75)
    01.01003,12. ASTM (4-1-72)
    01.01003,13. Attainment Area (11-1-84)
    01.01003,14. Background Level (6-20-74)
    01.01003,15. Baseline (Area, Concentration, Date) (12-31-91)
    01.01003,16. Best Available Control Technology (BACT) (11-1-84)
    01.01003,17. Board (6-20-74)
    01.01003,18. BTU (11-1-84)
    01.01003,19. Collection Efficiency (4-1-72)
    01.01003,20. Commence Construction or Modification (11-1-84)
    01.01003,21. Complete (11-1-84)
    01.01003,22. Construction (11-1-84)
    01.01003,23. Control Equipment (4-1-72)
    01.01003,24. Controlled Emission (4-1-72)
    01.01003,25. Criteria Pollutant (11-1-84)
    01.01003,26. Department (6-20-74)
    01.01003,27. Designated Facility (11-1-84)
    01.01003,28. Director (12-31-91)
    01.01003,29. Emission (8-21-92)
    01.01003,30. Emission Standard (11-1-84)
    01.01003,31. Emission Standard Violation (11-1-84)
    01.01003,32. Emissions Unit (11-1-84)
    01.01003,33. Equivalent Air-Dried Kraft Pulp (5-16-71)
    01.01003,34. Existing Stationary Source or Facility (11-1-84)
    01.01003,35. Facility (11-1-84)
    01.01003,36. Federal Class I Area (12-31-91)
    01.01003,37. Federal Land Manager (11-1-84)
    01.01003,38. Fire Hazard (3-12-85)
    01.01003,39. Fuel-Burning Equipment (4-1-72)
    01.01003,40. Fugitive Dust (11-1-84)
    01.01003,41. Fugitive Emissions (11-1-84)
    01.01003,42. Garbage (3-12-85)
    01.01003,43. Hazardous Air Pollutant (11-1-84)
    01.01003,44. Hazardous Waste (3-12-85)
    01.01003,45. Hot-Mix Asphalt Plant (1-24-69)
    01.01003,46. Incinerator (4-1-72)
    01.01003,47. Indian Governing Body (11-1-84)
    01.01003,48. Indian Reservation (11-1-84)
    01.01003,49. Industrial Process (11-1-84)
    01.01003,50. Innovative Control Technology (11-1-84)
    01.01003,51. Integral Vista (11-1-84)
    01.01003,52. Kraft Pulping (5-16-71)
    01.01003,53. Lowest Achievable Emission Rate (LAER) (11-1-84)
    01.01003,54. Major Facility (11-1-84)
    01.01003,55. Major Modification (11-1-84)
    01.01003,56. Malfunction (12-5-74)
    01.01003,57. Mandatory Federal Class I Area (11-1-84)
    01.01003,58. Modification (11-1-84)
    01.01003,59. Monitoring (4-1-72)
    01.01003,60. Multiple Chamber Incinerator (4-1-72)
    01.01003,61. Net Emissions Increase (12-31-91)
    01.01003,62. New Stationary Source or Facility (12-31-91)
    01.01003,63. Nonattainment Area (11-1-84)
    01.01003,64. Noncondensables (4-1-72)
    01.01003,65. Odor (4-1-72)
    01.01003,66. Opacity (11-1-84)
    01.01003,67. Open Burning (4-1-72)
    01.01003,68. Operating Permit (12-31-91)
    01.01003,69. Particulate Matter (4-1-72)
    01.01003,70. Particulate Matter Emissions (5-16-90)
    01.01003,71. Permit to Construct (12-31-91)
    01.01003,72. Person (11-1-84)
    01.01003,73. PM-10 (5-16-90)
    01.01003,74. PM-10 Emissions (5-16-90)
    01.01003,75. Portable Equipment (11-1-84)
    01.01003,76. PPM (parts per million) (4-1-72)
    01.01003,77. Prescribed Fire Management Burning (3-12-85)
    01.01003,78. Primary Ambient Air Quality Standard (4-1-72)
    01.01003,79. Process or Process Equipment (11-1-84)
    01.01003,80. Process Weight (11-1-84)
    01.01003,81. Process Weight Rate (11-1-84)
    01.01003,82. Reasonable Further Progress (RFP) (11-1-84)
    01.01003,83. Salvage Operations (4-1-72)
    01.01003,84. Secondary Ambient Air Quality Standard (4-1-72)
    01.01003,85. Secondary Emissions (11-1-84)
    01.01003,86. Significant (5-16-90)
    01.01003,87. Significant Contribution (5-16-90)
    01.01003,88. Small Fire (3-12-85)
    01.01003,89. Smoke (4-1-72)
    01.01003,90. Smoke Management Plan (12-31-91)
    01.01003,91. Smoke Management Program (3-12-85)
    01.01003,92. Source (11-1-84)
    01.01003,93. Source Operation (4-1-72)

[[Page 297]]

    01.01003,94. Stack (3-3-87)
    01.01003,95. Standard Conditions (12-31-91)
    01.01003,96. Stationary Source (11-1-84)
    01.01003,97. Time Intervals (11-1-84)
    01.01003,98. Total Suspended Particulates (5-16-90)
    01.01003,99. Trade Wastes (3-12-85)
    01.01003,100. TRS (total reduced sulfur) (5-16-71)
    01.01003,101. Unclassifiable Area (11-1-84)
    01.01003,102. Uncontrolled Emission (11-1-84)
    01.01003,103. Visibility Impairment (11-1-84)
    01.01003,104. Wigwam Burner (4-1-72)
    01.01004, Incorporations by Reference (12-31-91)
    01.01004,01. Locations Within the Department (12-31-91)
    01.01004,02. Federal Publications (5-16-90)
    01.01005. Reporting
    01.01005,01. Requirements by Department (6-26-75)
    01.01005,02. Requirements by Administrator (10-25-72)
    01.01005,03. Format of Reports (4-1-72)
    01.01005,04. Conformance to Rules (12-31-91)
    01.01006. Upset Conditions, Breakdown (12-31-91)
    01.01006,01. Upset Reports (5-7-76)
    01.01006,02. Scheduled Maintenance (5-7-76)
    01.01006,03. Correction of Condition (5-7-76)
    01.01006,04. Auxiliary Equipment (5-7-76)
    01.01008. Circumvention (12-31-91)
    01.01009. Total Compliance (1-24-69)
    01.01010. Sampling and Analytical Procedures (1-24-69)
    01.01011. Provisions Governing Specific Activities
    01.01011,01. Toxic Substances (12-31-91)
    01.01011,02. Modifying Physical Conditions (1-24-69)
    01.01011,03. Source Density (12-31-91)
    01.01011,04. Polychlorinated Biphenyls (PCBs) (12-31-91))
    01.01012. Procedures and Requirements for Permits to Construct and 
Operating Permits
    01.01012,01. Purpose (12-31-91)
    01.01012,02. Permit to Construct (12-31-91)
    01.01012,03. Operating Permit (12-31-91)
    01.01012,04. Application Procedures (12-31-91)
    01.01012,05. Permit Requirements for New and Modified Stationary 
Sources (11-1-84)
    01.01012,06. Permit Requirements for New Major Facilities or Major 
Modifications in Nonattainment Areas (12-31-91)
    01.01012,07. Permit Requirements for New Major Facilities or Major 
Modifications in Attainment or Unclassifiable Areas (12-31-91)
    01.01012,08. Optional Offsets for Permits to Construct (12-31-91)
    01.01012,09. Requirements for Alternative Emission Limits (Bubbles) 
(12-31-91)
    01.01012,10. Requirements for Banking Emission Reduction Credits 
(ERC's) (12-31-91)
    01.01012,11. Requirements for Emission Reduction Credit (11-1-84)
    01.01012,12. Demonstration of Net Air Quality Benefit and Ambient 
Equivalence (5-16-90)
    01.01012,13. Procedure for Issuing Permits (12-31-91)
    01.01012,14. Conditions for Permits to Construct and Operating 
Permits (12-31-91)
    01.01012,15. Obligation to Comply (11-1-84)
    01.01013. Registration Procedures and Requirements for Portable 
Equipment
    01.01013,01. Registration Requirements (12-31-91)
    01.01013,02. Compliance with Regulations (11-1-84)
    01.01014. Stack Heights and Dispersion Techniques
    01.01014,01. Applicability (3-3-87)
    01.01014,02. Definitions (12-31-91)
    01.01014,03. Requirements (3-3-87)
    01.01014,04. Opportunity for Public Hearing (12-31-91)
    01.01014,05. Approval of Field Studies and Fluid Models (12-31-91)
    01.01014,06. No Restriction on Actual Stack Height (3-3-87)
    01.01015--01.01050 (Reserved)
    01.01051. Air Pollution Emergency Regulation (12-31-91)
    01.01052. Episode Criteria
    01.01052,01. Stages (6-28-78)
    01.01052,02. Effect of Stages (6-28-78)
    01.01052,03. Criteria for Defining Episode Stages (6-28-78)
    01.01052,04. Episode Stages: Emergency Episode Air Pollution 
Criteria--Table (4-1-72)
    01.01052,05. Criteria for Defining Levels Within Stages (6-28-78)
    01.01053. Public Notification
    01.01053,01. Information to be Given (12-31-91)
    01.01053,02. Manner and Frequency of Notification (4-1-72)
    01.01053,03. Notification to Sources (6-28-78)
    01.01054. General Rules (6-28-78)
    01.01054.01 Stage 1--Air Pollution Forecast (6-28-78)
    01.01054,02. Stage 2--Alert (6-28-78)
    01.01054,03. Stage 3--Warning (6-28-78)
    01.01054,04. Stage 4--Emergency (12-31-91)
    01.01055. Specific Emergency Episode Abatement Plans for Point 
Sources (12-31-91)
    01.01056--01.01100 (Reserved)
    01.01101. Air Quality Standards and Area Classification
    01.01101,01. Ambient Air Quality Standards (12-31-91)
    01.01101,02. Designation of Attainment, Unclassifiable, and 
Nonattainment Areas (11-1-84)

[[Page 298]]

    01.01101,03. Baselines for Prevention of Significant Deterioration 
(5-16-90)
    01.01101,04. Classification of Prevention of Significant 
Deterioration Areas (11-1-84) except for 01.01101,04.b.ii(a) (12-31-91)
    01.01101,05. Prevention of Significant Deterioration (PSD) 
Increments (12-31-91)
    01.01102--01.01150 (Reserved)
    01.01151. Rules for Control of Open Burning
    01.01151,01. Purpose and Effective Date (12-31-91)
    01.01151,02. Fire Permits, Hazardous Materials and Liability (12-31-
91)
    01.01151,03. Nonpreemption of Other Jurisdictions (12-31-91)
    01.01151,04. General Restrictions (12-31-91)
    01.01151,05. Alternatives to Open Burning (12-31-91)
    01.01152 (Reserved)
    01.01153. Categories of Allowable Burning (12-31-91)
    01.01153,01. Recreational and Warming Fires (3-12-85)
    01.01153,02. Weed Control Fires (3-12-85)
    01.01153,03. Training Fires (12-31-91)
    01.01153,04. Industrial Flares (3-12-85)
    01.01153,05. Residential Solid Waste Disposal Fires (3-12-85)
    01.01153,06. Landfill Disposal Site fires (12-31-91)
    01.01153,07. Orchard Fires (12-31-91)
    01.01153,08. Prescribed Burning (12-31-91) 2401.01153,09. Dangerous 
Material Fires (3-12-85)
    01.01153,10. Infectious Waste Burning (12-31-91)
    01.01154--01.01200 (Reserved)
    01.01201. Visible Emissions (12-21-79)
    01.01201,01. Exemptions (12-21-79)
    01.01201,02. Standards for Exempted Sources (12-31-91)
    01.01201,03. Exception (12-31-91)
    01.01202 (Reserved)
    01.01203. General Restrictions of Visible Emissions From Wigwam 
Burners (12-21-79)
    01.01204--01.01250 (Reserved)
    01.01251. Rules for Control of Fugitive Dust (12-31-91)
    01.01252. General Rules
    01.01252,01. Use of Water or Chemicals (1-25-79)
    01.01252,02. Application of Dust Suppressants (1-25-79)
    01.01252,03. Use of Control Equipment (1-25-79)
    01.01252,04. Covering of Trucks (1-25-79)
    01.01252,05. Paving (1-25-79)
    01.01252,06. Removal of Materials (1-25-79)
    01.01253--01.01300 (Reserved)
    01.01301. Fuel Burning Equipment--Particulate Matter
    01.01301,01. Standards for New Sources (12-21-79)
    01.01301,02. Standards for Minor and Existing Sources (12-21-79)
    01.01301,03. Combinations of Fuels (12-21-79)
    01.01301,04. Averaging Period (12-31-91)
    01.01301,05. Altitude Correction (12-31-91)
    01.10302--01.01326 (Reserved)
    01.01327. Emission Limitations (1-24-69)
    01.01328. Allowable Rate of Emission Based on Process Weight Rate--
Table (1-24-69)
    01.01329. Particulate Matter--New Equipment Process Weight 
Limitations
    01.01329,01. General Restrictions (12-21-79)
    01.01329,02. Minimum Allowable Emission (12-31-91)
    01.10329,03. Averaging Period (12-31-91)
    01.01329,04. Exemption (12-31-91)
    01.01329,05. Emission Standards--Table (12-31-91)
    01.01330. Particulate Matter--Existing Equipment Process Weight 
Limitations (12-31-91)
    01.01330,01. General Restrictions (12-21-79)
    01.01330,02. Minimum Allowable Emission (12-31-91)
    01.01330,03. Averaging Period (12-31-91)
    01.01330,04. Exemptions (12-31-91)
    01.01330,05. Emission Standards--Table (12-31-91)
    01.01331--01.01350 (Reserved)
    01.01351. Rules for Sulfur Content of Fuels (12-31-91)
    01.01352. Definitions as Used in This Regulation
    01.01352,01. ASTM (4-1-72)
    01.01352,02. Distillate Fuel Oil (4-1-72)
    01.01352,03. Residual Fuel Oil (4-1-72)
    01.01353. Residual Fuel Oils
    01.01353,01. Standards for 1973 (6-28-78)
    01.10353,02. Standards Beginning 1974 (6-28-78)
    01.01354. Distillate Fuel Oil
    01.01354,01. ASTM Grade 1 (4-1-72)
    01.01354.02. ASTM Grade 2 (4-1-72)
    01.01355. Coal (4-1-72)
    01.01356--01.01400 (Reserved)
    01.01401. Rules for Control of Fluoride Emissions (12-31-91)
    01.01402. General Rules (12-31-91)
    01.01402,01. Emission Limitations--Phosphate Fertilizer Plants (12-
31-91)
    01.01402,02. Monitoring, Testing, and Reporting Requirements (12-31-
91)
    01.01402,03. Source Specific Permits (12-31-91)
    01.01402,04. Exemptions (12-31-91)
    01.01403--01.01450 (Reserved)
    01.01451. Rules for Control of Odors (12-31-91)
    01.01452. General Rules
    01.01452,01. General Restrictions (4-1-72)
    01.01452,02. Restrictions on Rendering Plants (4-1-72)
    01.01453--01.01500 (Reserved)
    01.01501. Rules for Control of Incinerators (12-31-91)
    01.01502. Emission Limits (4-1-72)
    01.01503. Design Standards (4-1-72)
    01.01504. Exceptions (12-31-91)
    01.01505--01.01550 (Reserved)

[[Page 299]]

    01.01551. Rules for Control of Motor Vehicle Emissions (12-31-91)
    01.01552. Pollution Control Devices (4-1-72)
    01.01553. Visible Emission Standards (4-1-72)
    01.01554--01.01600 (Reserved)
    01.01601. Rules for Control of Hot-Mix Asphalt Plants (12-31-91)
    01.01602. Emission Limits (12-31-91)
    01.01603 (Reserved)
    01.01604. Multiple Stacks (1-24-69)
    01.01605. Fugitive Dust Control
    01.01605,01. Fugitive Emission Controls (1-24-69)
    01.01605,02. Plant Property Dust Controls (1-24-69)
    01.01606--01.01650 (Reserved)
    01.01651. Rules for Control of Kraft Pulping Mills (12-31-91)
    01.01652. Statement of Policy
    01.01652,01. Best Treatment and Control (5-16-71)
    01.01652,02. Monitoring (5-16-71)
    01.01652,03. Research (5-16-71)
    01.01652,04. Available Technology Required (5-16-71)
    01.01652,05. New Source Standards (5-16-71)
    01.10653. General Rules (12-31-91)
    01.01654. Recovery Furnace Standards (5-16-71)
    01.01655. Recovery Furnace TRS Standards (5-16-71)
    01.01656. Digester and Evaporator Standards (5-16-71)
    01.01657. Recovery Furnace Particulate Standards (5-16-71)
    01.01658. Lime Kiln Standards (5-16-71)
    01.01659. Smelt Tank Standards (5-16-71)
    01.01660. Monitoring and Reporting
    01.01660,01. Continuous TRS Monitoring (5-16-71)
    01.01660,02. Particulate Monitoring (5-16-71)
    01.01660,03. Monitoring Program (12-31-91)
    01.01660,04. Reporting (5-16-71)
    01.01660,05. Miscellaneous Reports (5-16-71)
    01.01661. Special Studies
    01.01661,01. Areas to be Included (5-16-71)
    01.01661,02. Additional Studies (5-16-71)
    01.01662. Exceptions (12-31-91)
    01.01663--01.01750 (Reserved)
    01.01751. Rules for Control of Rendering Plants (12-31-91)
    01.01752. Control of Cookers (4-1-72)
    01.01753. Control of Expellers (4-1-72)
    01.10754. Control of Plant Air (4-1-72)
    01.01755. Exceptions (12-31-91)
    01.01756--01.01800 (Reserved)
    01.01801. Rules for Control of Sulfur Oxide Emissions From Sulfanic 
Acid Plants (12-31-91)
    01.01802. General Restrictions (10-25-72)
    01.01803. Monitoring and Testing (12-31-91)
    01.01804. Compliance Schedule (12-31-91)
    01.01805--01.01852 (Reserved)
    01.01855 (Reserved)
    01.01857--01.01950 (Reserved)
    01.01969--01.01995 (Reserved)
    01.01996. Administrative Provisions (12-31-91)
    01.01998. Inclusive Gender and Number (12-31-91)
    01.01999. Severability (12-31-91)
Appendix B Emission Inventory--Ada Country Carbon Monoxide NonAttainment 
          Area (submitted 1/15/80)
Appendix G Permits--Silver Valley (submitted 1/15/80)
Appendix H Permits--Lewiston (submitted 12/4/80, 2/5/81)
Appendix J Permits--Pocatello (submitted 3/7/80)
Appendix K Permits--Soda Springs (submitted 1/15/80)
Beker Industries, 1973 Consent Order (40 CFR 52.670(c)(15)--SO2 Emission 
          Limitation (submitted 7/28/75)
40 CFR part 52, subparts A and N
[58 FR 39448, July 23, 1993]



Sec. 52.680  [Reserved]



Sec. 52.681  Permits to construct and operating permits.

    (a) Emission limitations and other provisions contained in Permits 
to Construct or Operating permits, issued by the State of Idaho 
Department of Health and Welfare in accordance with the federally-
approved Rules and Regulations for the Control of Air Pollution in Idaho 
Manual sections 16.01.01002 Definitions, 16.01.01012 Procedures and 
Requirements for Permits to Construct and Operating Permits, 16.01.01014 
Stack Heights and Dispersion Techniques, and 16.01.01101 Ambient Air 
Quality Standards and Area Classifications, except for Operating Permits 
authorizing the use of alternative emission limits (bubbles) under 
sections 16.01.01012,03.a(1) and 16.01.01012,09 or compliance schedule 
extensions under section 16.01.01012,03.d, shall be the applicable 
requirements of the federally-approved Idaho SIP (in lieu of any other 
provisions) for the purposes of section 113 of the Clean Air Act and 
shall be enforceable by EPA and by any person in the same manner as 
other requirements of the SIP.
    (b) Operating Permits authorizing the use of alternative emission 
limits (bubbles) under sections 16.01.01012,03.a(1) and 16.01.01012,09, 
including the use of banked emission reduction credits pursuant to 
section 16.01.01012,10 in a bubble, and operating

[[Page 300]]

permits authorizing compliance schedule extensions under section 
16.01.01012,03.d, must be submitted to EPA for approval as revisions to 
the Idaho SIP before they shall become the applicable requirements of 
the SIP.
[58 FR 39450, July 23, 1993]



Sec. 52.682  [Reserved]



Sec. 52.683  Significant deterioration of air quality.

    (a) The Rules and Regulations for the Control of Air Pollution in 
Idaho Manual, specifically, sections 16.01.01002 Definitions, 
16.01.01012 Procedures and Requirements for Permits to Construct and 
Operating Permits, 16.01.01014 Stack Heights and Dispersion Techniques, 
and 16.01.01101 Ambient Air Quality Standards and Area Classifications, 
are approved as meeting the requirements of part C of the Clean Air Act 
for preventing significant deterioration of air quality.
    (b) The requirements of sections 160 through 165 of the Clean Air 
Act are not met for Indian reservations since the plan does not include 
approvable procedures for preventing significant deterioration of air 
quality on Indian reservations. Therefore, the provisions of Sec. 52.21 
(b) through (w) are hereby incorporated and made part of the applicable 
plan for Indian reservations in the State of Idaho.
    (c) The requirements of section 165 of the Clean Air Act are not met 
for sources subject to prevention of significant deterioration 
requirements prior to August 22, 1986, the effective date of EPA's 
approval of the rules cited in paragraph (a) of this section. Therefore, 
the provisions of Sec. 52.21(b), (c), (d), and (h) through (w) are 
hereby incorporated and made part of the applicable plan for sources 
subject to Sec. 52.21 prior to August 22, 1986.
[58 FR 39450, July 23, 1993]



Sec. 52.684--52.689  [Reserved]



Sec. 52.690  Visibility protection.

    (a) The requirements of section 169A of the Clean Air Act are not 
met, because the plan does not include approvable procedures for 
protection of visibility in mandatory Class I Federal areas.
    (b) Regulation for visibility monitoring. The provisions of 
Sec. 52.26 are hereby incorporated and made a part of the applicable 
plan for the State of Idaho.
    (c) Long-term strategy. The provisions of Sec. 52.29 are hereby 
incorporated and made part of the applicable plan for the State of 
Idaho.
[50 FR 28553, July 12, 1985; 51 FR 23759, July 1, 1986, as amended at 52 
FR 45137, Nov. 24, 1987]



Sec. 52.691  Extensions.

    (a) The Administrator, by authority delegated under section 188(d) 
of the Clean Air Act, as amended in 1990, hereby extends for one year 
(until December 31, 1995) the attainment date for the Power-Bannock 
Counties PM-10 nonattainment area and the Sandpoint PM-10 nonattainment 
area.
    (b) The Administrator, by authority delegated under section 188(d) 
of the Clean Air Act, as amended in 1990, hereby grants a second one-
year extension (until December 31, 1996) to the attainment date for the 
Power-Bannock Counties PM-10 nonattainment area.
[61 FR 20732, May 8, 1996, as amended at 61 FR 66606, Dec. 18, 1996]



                           Subpart O--Illinois



Sec. 52.719  Identification of plan--conditional approval.

    The plan revision commitments listed in paragraph (a) of this 
section were submitted on the date specified.
    (a) On May 15, 1992, Illinois submitted a part D particulate matter 
(PM) nonattainment area plan for the Lake Calumet, McCook, and Granite 
City moderate nonattainment areas. This plan included control measures 
adopted in a final opinion and order of the Illinois Pollution Control 
Board, on April 9, 1992, in proceeding R91-22. The USEPA is 
conditionally approving the State's plan, contingent on fulfillment of 
the State's commitment to meet 5 requirements by November 20, 1995. The 
first requirement is for the State to adopt and submit additional 
enforceable control measures, if necessary, that will achieve 
attainment. The second requirement is for the State to submit a complete 
and accurate emissions inventory (including corrected emissions

[[Page 301]]

estimates, as well as any new control measures which may be needed) and 
an acceptable modeled attainment demonstration. The third requirement is 
for the State to impose an opacity limit for coke oven combustion stacks 
which is reflective of their mass emission limits. The fourth 
requirement is for the State to provide an appropriate regulation for 
the electric arc furnaces at American Steel Foundries. The fifth 
requirement is for the State to correct the following three other 
enforcement concerns: First, section 212.107, Measurement Methods for 
Visible Emissions, states that Method 22 should be used for ``detection 
of visible emissions''. This could be misinterpreted as requiring use of 
Method 22 for sources subject to opacity limits as well as sources 
subject to limits on detectability of visible emissions. USEPA 
recommends revising the language of the rule to state that ``for both 
process emission sources and fugitive particulate matter sources, a 
determination as to the presence or absence of visible emissions shall 
be in accordance with Method 22''. Second, measurement methods for 
opacity, visible emissions, and ``PM'' are in section 212.110, and in 
separate sections 212.107, 212.108, and 212.109. The measurement methods 
in these sections are not always consistent with each other. USEPA 
recommends that the measurement methods in 212.107, 212.108, and 212.109 
be integrated with section 212.110. Third, several of the submitted 
rules contain language which exempts sources with no visible emissions 
from mass emissions limits. It is USEPA's understanding that the State 
intends for these exemptions to apply to small, well-controlled sources. 
However, the way the exemptions are worded, they could be misinterpreted 
to exclude many other sources from mass emissions limits. The rules 
containing these exemptions need to be clearer about exactly what 
sources are to be exempt, and when. If the State fails to meet any 
portion of its commitment by the date listed above, the USEPA's 
conditional approval will automatically become a limited approval/
disapproval without further regulatory action.

                     (1) Incorporation by reference.

    (i) Illinois Administrative Code Title 35: Environmental Protection, 
Subtitle B: Air Pollution, Chapter 1: Pollution Control Board, 
Subchapter c: Emission Standards and Limitations for Stationary Sources, 
Part 211:
    Definitions and General Provisions, Subpart A: General Provisions, 
Section 211.101. Adopted at 16 Illinois Register 7656, effective May 1, 
1992. (ii) Illinois Administrative Code Title 35: Environmental 
Protection, Subtitle B: Air Pollution, Chapter 1: Pollution Control 
Board, Subchapter c: Emission Standards and Limitations for Stationary 
Sources, Part 212: Visible and Particulate Matter Emissions, Subpart A: 
General, Sections 212.107, 212.108, 212.109, 212.110, 212.113; Subpart 
E: Particulate Matter Emissions from Fuel Combustion Sources, Section 
212.210; Subpart K: Fugitive Particulate Matter, Sections 212.302, 
212.309, 212.316; Subpart L: Particulate Matter from Process Emission 
Sources, Section 212.324; Subpart N: Food Manufacturing, Section 
212.362; Subpart Q: Stone, Clay, Glass and Concrete Manufacturing, 
Section 212.425; Subpart R: Primary and Fabricated Metal Products and 
Machinery Manufacture, Section 212.458; Subpart S: Agriculture, Section 
212.464; Section 212 Illustration D: McCook Vicinity Map, Illustration 
E: Lake Calumet Vicinity Map, and Illustration F: Granite City Vicinity 
Map. Adopted at 16 Illinois Register 7880, effective May 11, 1992.
    (b) [Reserved]
[59 FR 59656, Nov. 18, 1994]



Sec. 52.720  Identification of plan.

    (a) Title of plan: ``State of Illinois Air Pollution Implementation 
Plan.''
    (b) The plan was officially submitted on January 31, 1972.
    (c) The plan revision listed below were submitted on the dates 
specified.
    (1) The role of the City of Chicago as a local agent was defined in 
a letter from the State Environmental Protection Agency on March 13, 
1972.
    (2) Copies of the Illinois Pollution Control Board Regulations, 
Chapter 2, Parts I, II and III were submitted May 4, 1972, by the 
Governor.

[[Page 302]]

    (3) A document describing the role of the Chicago Department of 
Environmental Control was submitted July 28, 1972, by the State 
Environmental Protection Agency.
    (4) Copies of the revisions to the State air episode regulations 
were submitted on August 29, 1972, by the Governor.
    (5) Compliance schedules submitted on March 13, 1973, by the 
Pollution Control Board.
    (6) Compliance schedules submitted on April 3, 1973, by the 
Pollution Control Board.
    (7) Transportation control plan submitted on April 17, 1973, by the 
Pollution Control Board.
    (8) Compliance schedules submitted on May 3, 1973, by the Pollution 
Control Board.
    (9) Compliance schedules submitted on June 15, 1973, by the 
Pollution Control Board.
    (10) Compliance schedules submitted on August 7, 1973, by the 
Pollution Control Board.
    (11) Information concerning the coal ban in the Chicago area was 
submitted on October 22, 1973, by Governor Walker.
    (12) On July 22, 1976, the Director of the Illinois Environmental 
Protection Agency submitted revised emergency episode regulations.
    (13) On November 29, 1977, the Director of the Illinois 
Environmental Protection Agency submitted grain handling and drying 
emission limitations as revisions to Rule 203.
    (14) Revision consisting of an Illinois Pollution Control Board 
Order issued on July 20, 1978 to Commonwealth Edison Company, Christian 
County, Illinois and submitted on August 14, 1978 by the Illinois 
Environmental Protection Agency.
    (15) Revision consisting of an Illinois Pollution Control Board 
Order issued to Shell Oil Company's Wood River refinery on December 14, 
1978 by the Illinois Environmental Protection Agency.
    (16) On April 4, 1979, the State submitted its draft nonattainment 
area plan for all areas designated nonattainment as of March 3, 1978 and 
as revised on October 5, 1978. This submittal contained a request for 
extensions of the statutory attainment deadline for CO and 03. The 
submittal also included a vehicle emission inspection and maintenance 
program and a new source review plan. Although the State submittal also 
included the following provisions, U.S. EPA is taking no action to 
include them in the federally approved SIP at this time: the portions of 
Rules 101, 103 and 105 relating to the provisions addressing 
malfunctions, general requirements of the Clean Air Act which are not 
Part D requirements, and the provisions covering open burning, mobile 
source emission standards, diesel locomotive emission standards, sulfur 
dioxide emissions for certain fuel combustion sources located outside 
major metropolitan areas, compliance dates for organic emission 
limitations, particulate emissions from low carbon waste incinerators, 
and adoption of Federal New Source Performance Standards. In addition, 
U.S. EPA is not rulemaking at this time on those portions of the 
following rules which contain specified changes made between the 
publication of the notice of proposed rulemaking and the final 
rulemaking action:
    (i)--(iii) [Reserved]
    (iv) The new materials in Section 4.11 of the Rules for Issuance of 
Permits to New or Modified Air Pollution Sources;
    (v) The addition of a definition of ``reconstruction'' in Section 
4.7 of the Rules for Issuance of Permits;
    (vi) The procedure allowing external offsets contained in Section 10 
of the Rules for Issuance of Permits.
    (17) On August 29, 1979, the State submitted additional information 
and clarification for the nonattainment area plan in response to USEPA's 
July 2, 1979 notice of proposed rulemaking.
    (18) On September 20, 1979, the State submitted a summary of public 
hearing comments on the plan.
    (19) On October 30, 1979, the State submitted copies of Illinois 
Pollution Control Board final orders for control of VOC emissions from 
stationary sources (Rule 205), sources of fugitive particulate (Rule 
203(f)), and particulate emissions from iron and steel sources (Rule 
203(d)).
    (20) On December 20, 1979, the State submitted a letter containing 
the dates

[[Page 303]]

that most of the regulatory and nonregulatory portions of the 
nonattainment area plans were finally adopted by the Illinois Pollution 
Control Board. Rule 205 containing RACT controls for stationary sources 
of VOC was effective in the State on July 18, 1979. Rule 203(f) 
governing fugitive dust emissions was effective in the State on 
September 18, 1979.
    (21) On January 25, 1980, the State submitted a copy of finally 
enacted ``Rules for the Issuance of Permits to New or Modified Air 
Pollution Sources Affecting Nonattainment Areas.'' Sections 
5.1(a)(2)(ii) and 5.1(a)(2)(iii) of these rules were reserved by the 
State. The effective date of these Rules was January 16, 1980.
    (22) On March 21, 1979, the State of Illinois submitted to the USEPA 
revised regulations for control of sulfur dioxide emissions. On 
September 19, 1979, the State submitted additional information on these 
revised regulations to the USEPA.
    (23) On January 17, 1980 and on February 7, 1980 the State submitted 
further information and clarifications to Rule 204.
    (24) On September 19, 1979, the State of Illinois submitted a 
revision to Rule 204(e)(1) for the Commonwealth Edison Company. The 
revision approves an emission limitation of 105,162 lbs SO2/
hour for the Kincaid Generating Station in Christian County, Illinois.
    (25) On April 30, 1980, the State submitted revisions to the 
transportation control plan for northeast Illinois (Chicago).
    (26) On December 20, 1979, the State of Illinois submitted a 
revision to provide for modification of the existing air quality 
surveillance network.
    (27) On January 8, 1980, the State submitted an Opinion and Final 
Order of the Pollution Control Board (dated November 19, 1979) which 
deletes Rule 206(d) of Chapter 2 from the Illinois Air Pollution Control 
Regulations.
    (28) On September 18, 1979, the State submitted a Final Order of the 
Pollution Control Board (dated April 12, 1979) which amended Rule 
205(g)(1) of Chapter 2 of the Illinois Air Pollution Control 
Regulations.
    (29) On July 21, 1981, the State submitted Volume 9 Lead, of the 
Illinois State Implementation Plan for Air Pollution Control for 
incorporation in the Illinois State Implementation Plan. This plan 
covers all areas in Illinois except for Granite City in the St. Louis 
Interstate AQCR.
    (30) On July 29, 1980, the State submitted a May 29, 1980, Opinion 
and Order of the Illinois Pollution Control Board granting a variance 
from the requirements Rule 203(d)(8)(B) of Chapter 2 of the Air 
Pollution Control Regulations to Continental Grain Company's grain 
elevator located in Crossville, White County, Illinois. This variance 
expired July 1, 1980.
    (31) On April 4, 1980, the State submitted a November 29, 1979, 
Opinion and Order of the Illinois Pollution Control Board (IPCB) and 
Supplementary IPCB Orders dated January 24, 1980, and February 7, 1980. 
These Orders grant 13 Caterpillar Tractor Company boilers a variance 
from the requirements of IPCB (A), Rule 203(g)(1)(C)(i) and/or Rule 
203(g)(1)(D) which regulate particulate emissions from new and existing 
sources. No action is taken at this time on variance provisions for 
Mapleton facility boilers 2, 3, 4, and 5. This variance expired on 
October 8, 1981.
    (32) On August 31, 1981, the State of Illinois submitted a revision 
to the Illinois State Implementation Plan in the form of a July 9, 1981, 
Order of the Illinois Pollution Control Board (R-77-15). This Order 
creates Rule 204(c)(1)(E) which establishes sulfur dioxide (SO2 
) emission limitations of 5.5 lbs/SO/MMBTU for solid fuel combustion 
sources having actual heat input not greater than 250 million BTU's per 
hour owned or operated by Bemis Company, Inc., Celotex Corporation or 
Sherex Corporation. On November 17, 1981, the State submitted additional 
information in support of this revision.
    (33) On August 20, 1980, and March 20, 1981, the State submitted 
additional information on the transportation control plans for the 
Northeast Illinois (Chicago) Area.
    (34) On October 15, 1980, the State submitted additional information 
on the transportation control plans for the Peoria Metropolitan Area.
    (35) On April 1, 1981, the State submitted additional information on 
the

[[Page 304]]

transportation control plans for the St. Louis Metropolitan (Illinois) 
Area.
    (36) On December 10, 1980, the State submitted a July 24, 1980, 
Opinion and Order of the Illinois Pollution Control Board and a 
September 18, 1980, Order of the Board granting Bunge Corporation's 
Cairo, Illinois soybean processing plant and grain elevator variance 
from Illinois Pollution Control Board's particulate emission standards 
under Rules 203(g)(1)(D) and 103(b)(1) of Chapter 2 of the Air Pollution 
Control Regulations through October 15, 1981.
    (37) On July 17, 1980, the State submitted an April 3, 1980, Opinion 
and Order of the Illinois Pollution Control Board adopting a December 
13, 1979, Proposed Opinion and Order of the Board which exempted certain 
small explosive waste incinerators from the requirements of Rule 203(e) 
Particulate Emission Standards and Limitations for incinerators and Rule 
206(b) Carbon Monoxide Emissions Standards and Limitations for 
incinerators.
    (38) On May 10, 1982, the State submitted a February 4, 1982, 
Illinois Pollution Control Board Opinion and Order (PCB 81-184) granting 
a variance from the requirements of Rules 205(m)(1)(B) and 204(n)(1)(G) 
of Chapter 2 of the Air Pollution Control Regulations to the Lyon Metal 
Products, Incorporated, Montgomery, Illinois facility. This variance 
expires on May 31, 1985.
    (39) On October 1, 1981, the State submitted a report in 
satisfaction of the Total Suspended Particulate Control Strategy 
approval condition in which the State agreed to conduct an analysis of 
the potential air quality impact from storage piles with uncontrolled 
emissions of less than 50 tons per year, to submit the results of any 
analysis to EPA, to submit any necessary regulations to the Illinois 
Pollution Control Board, and promulgate and submit any necessary 
regulations to EPA. This report concluded that no further regulations 
were needed.
    (40) EPA Study Volatile Organic Compound Emissions from Solvent 
Cleaning Operations in the State of Illinois (EPA 905/4-80-008) was 
prepared to satisfy the Ozone Control Strategy approval condition in 
which the State agreed to conduct a study to demonstrate that the three 
pound per hour, 15 pound per day exemption for solvent metal cleaners 
contained in Rule 205(k) represents RACT, to submit the results of the 
study to EPA, to submit the necessary regulations to the Illinois 
Pollution Control Board and promulgate and submit any necessary 
regulations to EPA. The State reviewed this report and in a February 11, 
1981, letter to EPA noted their agreement with the findings of the 
report and indicated that because there was no need for further 
regulations, this condition is satisfied.
    (41) On December 7, 1981, the State submitted a October 8, 1981, 
Illinois Pollution Control Board Final Order (R79-11). This Final Order 
amends Rule 203(g)(1) by adding subsection (E).
    (42) On January 4, 1983, the State submitted a revision to the 
Illinois State Implementation Plan in the form of an October 27, 1982, 
Illinois Pollution Control Board (IPCB) Opinion and Order (PCB 82-88). 
This Opinion and Order grants a variance from the requirements of Rule 
203(a) of Chapter 2 of the Air Pollution Control Regulations to a 
proposed fluidized bed combustion boiler at B.F. Goodrich's Henry 
County, Illinois facility. This variance continues until October 1, 
1987, or until the facility is no longer subject to Rule 206(a), 
whichever comes first.
    (43) On July 29, 1982, the State submitted a revision to the 
Illinois State Implementation Plan in the form of a May 28, 1981, 
Illinois Pollution Control Board (IPCB) Final Opinion of the Board (R78-
17). This Final Opinion deletes Rule 204(c)(1)(D) and the reference to 
it in Rule 204(h) from the IPCB Air Pollution Control Regulations.
    (44) On March 17, 1983, the Illinois Environmental Protection Agency 
(IEPA) submitted a revision to its ozone SIP for Chrysler's Belvidere 
facility. The revision request contains an alternative compliance time 
schedule with interim emission limitations which is in the form of a 
variance for prime coating and prime surface coating operations. Final 
compliance is changed from December 31, 1982 to December 31, 1987.
    (45) On August 19, 1983, the State of Illinois submitted a revision 
to the Illinois State Implementation Plan in the

[[Page 305]]

form of a July 26, 1983, Order of the Illinois Pollution Control Board 
(R82-12). This Order creates Rule 313 which establishes 1.5 micrograms 
per cubic meter, maximum arithmetic mean, averaged over a calendar 
quarter as the State's ambient air quality standard for lead. The Board 
also adopted, as part of Rule 313, a measurement method for determining 
compliance with the standard.
    (46) On August 15, 1983, the Illinois Environmental Protection 
Agency submitted a May 19, 1983, Opinion and Order (PCB-82-147) of the 
Illinois Pollution Control Board (IPCB) granting Del Monte Corporation's 
Can Manufacturing Plant No. 115 located in Rochelle, Ogle County, 
Illinois, a variance from the IPCB volatile organic compound emission 
standards under Rule 205(n)(1)(B)(i) and Rule 205(n)(1)(B)(vi) of 
Chapter 2: Air Pollution Regulations. The variance expires on December 
31, 1984.
    (47) On March 24, 1983, and May 3, 1983, the State submitted 
information that indicated that a February 21, 1980 (45 FR 11472), 
conditional approval of the incorporation of a revised Part D sulfur 
dioxide control strategy into the Illinois State Implementation Plan has 
been satisfied for Cincinnati, Pekin and Elm Grove Townships in Tazewell 
County and for Logan and Limestone Townships in Peoria County. This 
approval condition required that the SIP include a reanalysis of the 
Pekin, Illinois area; a submittal of the analysis results to USEPA; the 
proposal of any necessary regulations to the Illinois Pollution Control 
Board necessary to insure attainment and maintenance of the sulfur 
dioxide standard; and the promulgation of any necessary regulations. Any 
promulgated regulations must be submitted to USEPA.
    (48)--(49) [Reserved]
    (50) On May 3, 1983, the State requested that USEPA incorporate IPCB 
Rule 204 (f)(2) into the Illinois SIP. Rule 204(f)(2) was adopted by 
Illinois as part of a February 24, 1983, Order of the Board (R80-22). 
USEPA approves the incorporation of Rule 204(f)(2) as it pertains to 
Pekin Energy, a source in the Peoria major metropolitan area.
    (51) On January 30, 1984, the State submitted Rule 204(f) as 
contained in a February 24, 1983, Order of the IPCB (R80-22) as it 
applies to sources in the Peoria Major Metropolitan area for 
incorporation in the SIP. USEPA approves the incorporation of Rule 
204(f) into the SIP as it applies to all sources in Peoria and Tazewell 
Counties except Caterpillar Tractor Mapleton and East Peoria Plants. No 
action is taken on Rule 204(f) as it applies to the Chicago or St. Louis 
(Illinois--portion) Major Metropolitan Areas or on Rule 204(f) (1) and 
(2).
    (52) [Reserved]
    (53) On September 30, 1983, the State submitted a revision to the 
Illinois State Implementation Plan in the form of a lead plan to assure 
attainment and maintenance of the NAAQS in the Granite City area. The 
Illinois plan includes a discussion of air quality data measured since 
1978, an emission inventory of three source categories capable of 
emitting lead, atmospheric modeling analyses and proposed necessary 
control strategies. On March 19, 1984, the State submitted five consent 
decrees entered by the State of Illinois with the Circuit Court for the 
Third Judicial Circuit of Madison County and filed March 16, 1984, for 
incorporation in the lead plan. These include People of the State of 
Illinois vs. Taracorp, Inc.; People of the State of Illinois vs. St. 
Louis Lead Recyclers; People of the State of Illinois vs. First Granite 
City National Bank; People of the State of Illinois, vs. Stackorp Inc.; 
and People of the State of Illinois vs. B.V. and G.V. Transport Company.
    (54) [Reserved]
    (55) On November 14, 1985, the State of Illinois submitted a 
negative declaration for natural gas/gasoline processing plants.
    (i) Incorporation by reference.
    (A) Letter dated November 14, 1985, from Michael J. Hayes, Manager, 
Division of Air Pollution Control, Illinois Environmental Protection 
Agency.
    (56) On June 19, 1984, the State submitted Illinois Environmental 
Protection Agency Rule 252 entitled, ``Rules for Governing Public 
Participation in the Air Pollution Permit Program for Major Source in 
Nonattainment Areas.''
    (i) Incorporation by reference.

[[Page 306]]

    (A) Illinois Environmental Protection Agency Rule 252 entitled, 
``Rule for Governing Public Participation in the Air Pollution Permit 
Program for Major Sources in Nonattainment Areas,'' published on June 8, 
1984.
    (57)--(60) [Reserved]
    (61) On March 15, 1984 and June 14, 1984 the Illinois Environmental 
Protection Agency submitted commitments for satisfying several 
outstanding conditions to the sulfur dioxide [52.724(a)(1)] State 
Implementation Plan.
    (62) On January 16, 1985, the Illinois Environmental Protection 
Agency submitted a variance from Illinois Rule 206(a).
    (i) Incorporation by reference.
    (A) June 14, 1984, Opinion and Order of the Illinois Pollution 
Control Board (IPCB), PCB 84-19. This is a variance from Illinois Rule 
206(a) until June 14, 1987, for CO emissions from a fluidized bed 
combustion boiler at Midwest Solvents Company's facility in Tazewell 
County, Illinois.
    (63) On February 6, 1985, the Illinois Environmental Protection 
Agency (IEPA) submitted a site-specific revision to its total suspended 
particulates State Implementation Plan for Villa Grove's ``Dump and Boot 
Pit'' emissions in Champaign County, Illinois.
    (i) Incorporation by reference.
    (A) Illinois Pollution Control Board, Opinion and Order of the 
Board, PCB 84-53, Villa Grove's ``Dump and Boot Pit'' site-specific TSP 
revision. This revision extends the compliance date for control 
requirements on these emissions until September 1, 1987, and was adopted 
on July 14, 1984.
    (64) On May 13, 1985, the Illinois Environmental Protection Agency 
(IEPA) submitted a variance from Illinois Rule 202(b) for a Brule 
pathological waste incinerator (BPWI) at NPWC's facility located at the 
Great Lakes Naval Base, Great Lakes, Shields Township, Illinois, as a 
revision to its TSP SIP. Shields Township is an attainment area for both 
the primary and secondary national ambient air quality standards (NAAQS) 
for TSP.
    (i) Incorporation by reference.
    (A) Opinion and Order of the Illinois Pollution Control Board 84-156 
adopted on March 22, 1985.
    (65) Submitted from the Illinois Environmental Protection Agency 
(IEPA) dated July 22, 1985, requesting an extended compliance schedule 
for Precision Coatings Incorporated (PCI) coating Machine Number 2.
    (i) Incorporation by reference.
    (A) Illinois Pollution Control Board Opinion and Order of the Board, 
PCB 84-117, which was adopted on February 20, 1985, and a modification 
to PCB 84-117 which was adopted on April 14, 1985.
    (66) On March 27, 1985, the Illinois Environmental Protection Agency 
(IEPA) submitted a site-specific revision to its Carbon Monoxide State 
Implementation Plan for Anderson Clayton Foods, Inc. (ACF), a variance 
from 35 Illinois Administrative Code (IAC) 216.121 which governs Carbon 
Monoxide emissions from the Fluidized Bed Combuster retrofitted boiler 
at ACF's Jacksonville, Illinois facility. IAC 216.121 was incorporated 
in the Illinois SIP on May 31, 1972 (37 FR 10862), as Illinois Pollution 
Control Board Rule 206(a).
    (i) Incorporation by reference.
    (A) Illinois Pollution Control Board Opinion and Order of the Board, 
PCB 84-147, which was adopted on January 24, 1985.
    (67) On April 18, 1983, the State of Illinois submitted a 0.60 lb 
TSP/MMBTU emission limit for the City of Rochelle Municipal Steam Power 
Plant. On May 24, 1985, it submitted a revised modeling analysis.
    (i) Incorporation by reference.
    Illinois Pollution Control Board Order (R78-15), Rule 
203(g)(1)(C)(iii) which is dated February 24, 1983.
    (68) On May 8, 1985, the Illinois Environmental Protection Agency 
submitted a variance until December 31, 1987, from Illinois Rule 
205(n)(1)(b)(v) and Rule 205(n)(1)(b)(vi), for American Can 
Corporation's Hoopeston, Illinois facility in the form of a January 24, 
1985, Opinion and Order of the Illinois Pollution Control Board (PCB 84-
106).
    (i) Incorporation by reference. (A) A January 24, 1985, Opinion and 
Order of the Illinois Pollution Control Board (ICPB), PCB 84-106. This 
is a variance until December 31, 1987, for the coating reformulation 
programs at American Can Corporation's Hoopeston facility located in 
Hoopeston, Illinois.

[[Page 307]]

    (69) On January 28, 1983, the Illinois Environmental Protection 
Agency submitted a December 30, 1982, Illinois Pollution Control Board 
Order (R80-5). Illinois Pollution Control Board Rules 205(l) (4) through 
(10), 205(t) and 205(u) are approved.
    (i) Incorporation by reference. (A) Ilinois Pollution Control Board 
Rules 205(l)(4) through (10), 205(t) and 205(u) as contained in December 
30, 1982, Illinois Pollution Control Board Order R80-5.
    (ii) Additional material--none.
    (70) On February 13, 1986, the Illinois Environmental Protection 
Agency (IEPA) submitted a revision to its ozone SIP for the Fedders-
USA's facility located in Effingham, Effingham County, Illinois. It 
grants Fedders-USA a compliance date extension for control requirements 
from October 1, 1982, to April 1, 1986, and provides for a legally 
enforceable compliance program.
    (i) Incorporation by reference.
    (A) A January 9, 1986, Opinion and Order of the Illinois Pollution 
Control Board (IPCB), PCB 83-47.
    (71) On October 20, 1983, the Illinois Environmental Protection 
Agency submitted a site-specific revision to Illinois' sulfur dioxide 
plan for Illinois Power Company's Baldwin Power Station. The revised 
SO2 emission limitations are 101,966 lbs/hour, in the 
aggregate, and 6 lbs/MMBTU.
    (i) Incorporation by reference. (A) Emission limits within Paragraph 
1 of Illinois Pollution Control Board Final Order PCB 79-7, which was 
adopted September 8, 1983.
    (72) [Reserved]
    (73) On May 6, 1985, the Illinois Environmental Protection Agency, 
requested an extended compliance schedule for National Can Corporation's 
Rockford facility.
    (i) Incorporation by reference.
    (A) Illinois Pollution Control Board, April 1, 1982, Opinion and 
Order of the Board, PCB 81-189 and a January 24, 1985, Opinion and Order 
PCB 84-108. These orders grant National Can Corporation (Rockford Plant) 
a variance from the existing VOC SIP requirements from December 31, 
1982, until December 31, 1983, and from December 31, 1983, until 
December 31, 1985, respectively.
    (74) On October 30, 1986, the Illinois Environmental Protection 
Agency submitted a September 25, 1986, Final Order of the Illinois 
Pollution Control Board R85-33 revises the State's coke oven pushing and 
charging rules and recodifies some related rules.
    (i) Incorporation by reference. (A) Order of the Illinois Pollution 
Control Board R85-33, which was adopted September 25, 1986.
    (75)--(77) [Reserved]
    (78) On January 28, 1983, June 25, 1987, August 21, 1987, September 
28, 1987, October 2, 1987, December 22, 1987, January 8, 1988, March 29, 
1988, and May 2, 1988 the State submitted stationary source control 
measures for incorporation in the ozone plan.
    (i) Incorporation by reference. (A) The following sections of title 
35, Environmental Protection; subtitle B: Air Pollution; Chapter 1: 
Pollution Control Board of the Illinois Administrative Code, (June 
1989): section 211.122 (definitions of bead-dipping; component; dry 
cleaning facility; external floating roof; gas service; green tire 
spraying; green tires; heavy liquid; liquid mounted seal; liquid 
service; pneumatic rubber tire manufacture; refinery unit, process unit, 
or unit; tread end cementing; undertread cementing; valves not 
externally regulated; vapor collection system; vapor mounted primary 
seal; volatile organic liquid; and volatile organic material) of subpart 
B (part 211); section 215.104 (definitions of continuous process; in 
vacuum service; material recovery section; open-ended valve; polystyrene 
plant; polystyrene resin; repaired; styrene devolatilizer unit; and 
styrene recovery unit) of subpart A (part 215); sections 215.124, 
215.125, and 215.126 of subpart B (part 215); section 215.205 of subpart 
F (part 215); sections 215.240, 215.241, and 215.249 of subpart H (part 
215); section 215.408 of subpart P (part 215); sections 215.420 through 
215.431, 215.433, 215.434, 215.435, 215.437, and 215.438, all of subpart 
Q (part 215); section 215.453 of subpart R (part 215); sections 215.465 
and 215.466 of subpart S (part 215); sections 215.520, 215.521, 215.525, 
215.526, and 215.527 all of subpart V (part 215); sections 215.582, 
215,583, and 215.584 of subpart Y (part 215); sections 215.607 through 
215.613 of subpart Z (part 215); and sectons 215.875, 215.877,

[[Page 308]]

215.879, 215.881, 215.883, and 215.886 all of subpart BB (part 215) are 
approved.
    (ii) Additional material.
    (79) On March 20, 1986, November 17, 1986, and July 1, 1987, 
Illinois submitted its vehicle inspection and maintenance plan for the 
Chicago and East St. Louis areas.
    (i) Incorporation by reference. (A) Title 35: Environmental 
Protection, Subtitle B: Air Pollution, Chapter II: Environmental 
Protection Agency, Part 276, Procedures To Be Followed in the 
Performance of Annual Inspections of Motor Vehicle Exhaust Emissions, 
Adopted at 10 Illinois Register 13954, effective August 13, 1986.
    (ii) Additional material. (A) ``Technical Procedures Memorandum--
Enforcement'' between the Illinois Secretary of State and the Illinois 
Environmental Protection Agency, as submitted by Michael J. Hayes, 
Manager, Division of Air Pollution Control on July 1, 1987.
    (80) [Reserved]
    (81) On April 6, 1990, and May 4, 1990, Illinois submitted a 
regulation which reduced the maximum allowable volatility for gasoline 
sold in Illinois during July and August 1990 to 9.5 pounds per square 
inch.
    (i) Incorporation by reference
    (A) Title 35: Environmental protection, Subtitle B: Air pollution, 
Chapter I: Pollution control board, Part 215, Organic material emission 
standards and limitations, Sec. 215.585, Gasoline volatility standards, 
Adopted at 14 Illinois register 6434, effective April 11, 1990.
    (82)--(83) [Reserved]
    (84) On September 18, 1991, and November 18, 1991, the State 
submitted documents intended to satisfy federal requirements for an 
operating permit program which can issue federally enforceable operating 
permits.
    (i) Incorporation in Reference.
    (A) Public Act 87-555, an Act to amend the Environmental Protection 
Act by changing section 9.1, effective September 17, 1991. (Ch. 111 1/2, 
par. 1009.1) par. 1009.1(a), (b), (c), (d) and (f).
    (85) On March 24, 1988, the State submitted rules for issuance of 
construction permits to new and modified air pollution sources located 
in or affecting nonattainment areas (New Source Review rules).
    (i) Incorporation by reference.
    (A) Illinois Administrative Code, Title 35 Environmental Protection, 
Subtitle B: Air Pollution, Chapter 1: Pollution Control Board, Part 203: 
Major Stationary Sources.
    (86) On February 8, 1991, the State submitted revisions to its 
sulfur dioxide measurement methodology.
    (i) Incorporation by reference. (A) Title 35: Environmental 
Protection, Subtitle B: Air Pollution, Chapter 1: Pollution Control 
Board, Part 214 Sulfur Limitations, Subpart A: General Provisions, 
section 214.101 Measurement Methods. Adopted December 20, 1990, 
effective January 15, 1991.
    (87) On March 13, 1985, the State submitted revisions to its sulfur 
dioxide limitations.
    (i) Incorporation by reference.
    (A) Title 35: Environmental Protection, Subtitle B: Air Pollution, 
Chapter 1: Pollution Control Board, Part 214 Sulfur Limitations, Subpart 
C: Existing Solid Fuel Combustion Emission Sources, Section 214.141 
Sources Located in Metropolitan Areas, through paragraph (a) only, 
effective March 28, 1983; Subpart F: Alternative Standards for Sources 
Inside Metropolitan Areas, Section 214.201 Alternative Standards for 
Sources in Metropolitan Areas and Section 214.202 Dispersion Enhancement 
Techniques, effective March 28, 1983.

    (88) On June 9, 1986, the State submitted revisions to its sulfur 
dioxide limitations in the form of a April 24, 1986, opinion and order 
of the Illinois Pollution Board in proceeding R84-28.
    (i) Incorporation by reference.
    (A) Title 35: Environmental Protection, Subtitle B: Air Pollution 
Chapter 1: Pollution Control Board Part 214 Sulfur Limitations, Subpart 
C: Existing Solid Fuel Combustion Emission Sources, Sec. 214.141 Sources 
Located in Metropolitan Areas, paragraphs b), c) and d), and Subpart X: 
Utilities, Sec. 214.560 Scope and Sec. 214.561 E.D. Edwards Electric 
Generating Station effective May 20, 1986.

    (89) On March 17, 1989, and August 28, 1990, the State of Illinois 
submitted a revision to the Illinois State Implementation Plan. The 
revision is contained in subpart J, Sec. 201.281 and subpart L, 
Secs. 201.401-.408 of part 210 of title

[[Page 309]]

35 of the Illinois Administrative Code. This revision provides a legally 
enforceable procedure for continuously monitoring and recording 
emissions to determine the status of compliance of certain stationary 
source categories and complies with 40 CFR 51.214 and part 51, appendix 
P. The rules were adopted by the Illinois Pollution Control Board on 
December 15, 1988, published (13 Ill. Reg. 2066) and became effective 
February 3, 1989. The rules were corrected for an omission, published on 
November 15, 1989, (13 Ill Reg. 19444), and became effective December 5, 
1989. In a November 18, 1991, letter from Bharat Mathur, then Manager, 
Division of Air Pollution Control, Illinois Environmental Protection 
Agency (IEPA) to Stephen Rothblatt, Chief, Regulation Development 
Branch, Region 5, USEPA, Illinois committed to notify USEPA of any 
pending construction or operating permit application during the 30 day 
public comment period which is part of Illinois' permit issuance process 
(Section 203.150). This commitment is part of the administrative record 
of USEPA's approval of the Illinois' operating permit program for the 
purpose of issuing federally enforceable operating permits at 40 CFR 
52.720 (c) (84) and 52.737 on December 17, 1992 (57 FR 59928). USEPA may 
deem a permit not federally enforceable if monitoring provisions do not 
comply with the requirements of 40 CFR 51.214, part 51, appendix P or 
Sec. 51.165.
    (i) Incorporation by reference.
    (A) Title 35: Environmental Protection; Subtitle B: Air Pollution; 
Chapter I: Pollution Control Board; Subchapter a: Permits and General 
Provisions; Part 201: Permits and General Provisions, Subpart J: 
Monitoring and Testing, Section 201.281; and Subpart L: Continuous 
Monitoring, Sections 201.401 through 201.408, adopted at Ill. Reg. 2066, 
effective February 3, 1989.
    (90) On June 11, 1991, Illinois submitted regulations concerning the 
emission of volatile organic compounds from pharmaceutical 
manufacturing.
    (i) Incorporation by reference.
    (A) Title 35 of the Illinois Administrative Code: Environmental 
Protection, Subtitle B: Air Pollution, Chapter 1: Pollution Control 
Board, Subchapter C: Emissions Standards and Limitations for Stationary 
Sources, Part 215: Organic Material Emission Standards and Limitations, 
Subpart T: Pharmaceutical Manufacturing, Subpart A: General Provisions: 
Amendments to sections 215.102 and 215.105 and Creation of section 
215.108. Adopted at 15 Illinois Register 80 18, effective May 14, 1991.
    (B) Title 35 of the Illinois Administrative Code: Environmental 
Protection, Subtitle B: Air Pollution, Chapter 1: Pollution Control 
Board, Subchapter C: Emissions Standards and Limitations for Stationary 
Sources, Part 211: Definitions and General Provisions, Subpart B: 
Definitions. Adopted at 15 Illinois Register 79 01, effective May 14, 
1991.
    (91) [Reserved]
    (92) On June 4, 1992, the State submitted particulate matter 
regulations adopted as part of Pollution Control Board Proceeding R91-
35. These regulations concern particulate matter ambient limits and 
episode regulations.
    (i) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board
    (A) Part 212 Visible and Particulate Matter Emissions: Section 
212.113 Incorporations by Reference; section 212.424 Fugitive 
Particulate Matter Control for the Portland Cement Manufacturing Plant 
and Associated Quarry Operations located in LaSalle County, South of the 
Illinois River; section 212.443 Coke Plants; section 212.445 Blast 
Furnace Cast Houses; adopted at 16 Illinois Register 8204, effective May 
15, 1992.
    (B) Part 243 Air Quality Standards: Section 243.108 Incorporations 
by Reference; section 243.120 PM-10; section 243.121 
Repealed; adopted at 16 Illinois Register 8185, effective May 15, 1992.
    (C) Part 244 Episodes: Section 244.101 Definitions; section 244.106 
Monitoring; section 244.107 Determination of Areas Affected; section 
244.121 Local Agency Responsibilities; section 244.161 Advisory Alert 
and Emergency Levels; section 244.162 Criteria for Declaring and 
Advisory; section 244.163 Criteria for Declaring a Yellow Alert; section 
244.166 Criteria for Terminating Advisory, Alert and Emergency; section

[[Page 310]]

244.167 Episode Stage Notification; section 244.168 Contents of Episode 
Stage Notification; section 244.169 Actions During Episode Stages 
Adopted; section 244 appendix D; adopted at 16 Illinois Register 8191, 
effective May 15, 1992.
    (93) On September 30, 1992, the State submitted rules regulating 
volatile organic compound emissions from gasoline dispensing facilities' 
motor vehicle fuel operations.
    (i) Incorporation by reference.
    (A) Illinois Administrative Code, title 35 Environmental Protection, 
subtitle B: Air Pollution, chapter I: Pollution Control Board part 218: 
Organic Material Emission Standards and Limitations for the Chicago 
Area; subpart Y: Gasoline Distribution; Sec. 218.583 Gasoline Dispensing 
Facilities--Storage Tank Filling Operations, amended at 16 Illinois 
Register 13864 effective August 24, 1992, and; Sec. 218.586 Gasoline 
Dispensing Facilities--Motor Vehicle Fueling Operations, added at 16 
Illinois Register 13864, effective August 24, 1992.
    (B) [Reserved]
    (ii) Additional materials.
    (A) Stage II Vapor Recovery SIP Program Description dated September 
29, 1992.
    (94) On July 30, 1986, the State submitted particulate boiler rules 
intended to replace rule 203(g)(1) which was vacated by the Courts. No 
action is taken on Sec. 212.209 because the variance which it authorized 
has expired. On July 22, 1988, the State submitted opacity rules 
intended to replace rule 202(b) which had been vacated by the Courts. 
Also on July 22, 1988, the State submitted Illinois Pollution Control 
Board procedural rules for considering Air Adjusted Standard Procedures.
    (i) Incorporation by reference.
    (A) Title 35: Environmental Protection, Illinois Administrative 
Code, Subtitle B: Air Pollution; Chapter 1: Pollution Control Board; 
part 212 Visible and Particulate Matter Emissions; subpart E: 
Particulate Matter Emission from Fuel Combustion Emission Sources; 
Secs. 212.201, 212.202, 212.203 and 212.204. Amended or added at 10 Ill 
Reg. 12637, effective July 9, 1986.
    (B) Title 35: Environmental Protection, Illinois Administrative 
Code, Subtitle B: Air Pollution; Chapter 1: Pollution Control Board; 
part 212 Visible and Particulate Matter Emissions; subpart B: Visible 
Emissions. Amended or added at 12 Ill. Reg 12492, effective July 13, 
1988.
    (C) Title 35: Environmental Protection, Illinois Administrative 
Code; Subtitle A: General Provisions; Chapter 1: Pollution Control 
Board; part 106: Hearings Pursuant to Specific Rules; subpart E: Air 
Adjusted Standards Procedures. Added at 12 Ill. Reg 12484, effective 
July 13, 1988.
    (95) On October 16, 1991, and November 13, 1991, the State submitted 
particulate matter regulations adopted as part of Pollution Control 
Board Proceeding R91-6. These regulations concern particulate matter 
controls for LaSalle County, Illinois.
    (i) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board.
    (A) The addition of definitions for ``Condensible PM-10'', ``PM-
10'', ``Portland Cement Manufacturing Process Emission Source'', and the 
modification of the definition of ``Portland Cement Process'' to Part 
211 Definitions and General Provisions: Section 211.122 Definitions; 
adopted at 15 Illinois Register 15673, effective October 14, 1991.
    (B) Part 212 Visible and Particulate Matter Emissions: Section 
212.110 Measurement Methods; the addition of an abbreviation for pounds 
per hour to Section 212.111 Abbreviations and Units; additions and 
deletions to Section 212.113 Incorporations by Reference including the 
addition and/or renumbering of paragraphs (a), (b), (c), (d), (e), and 
(h) and the deletion of paragraphs earlier numbered as (a) and (f); 
Section 212.423 Emission Limits for Portland Cement the Manufacturing 
Plant Located in LaSalle County, South of the Illinois River; adopted at 
15 Illinois Register 15708, effective October 4, 1991.
    (96) On November 12, 1992, the State of Illinois submitted a Small 
Business Stationary Source Technical and Environmental Assistance 
Program for incorporation in the Illinois State Implementation Plan as 
required by section 507 of the Clean Air Act Amendments

[[Page 311]]

of 1990. Included in the State's submittal were a program description, 
newly adopted enabling legislation including new subsection 20 of 
section 39.5 of the Environmental Protection Act, Public Act 87-1213, 
and new subsection 46.13(a) of the Civil Administrative Code, Public Act 
87-1177, and a May 4, 1992, State of Illinois, Illinois Department of 
Commerce and Community Affairs (DCCA), Illinois Environmental Protection 
Agency (IEPA) Interagency Agreement defining the responsibilities of 
DCCA and IEPA in developing and implementing the Small Business 
Stationary Source Technical and Environmental Compliance Assistance 
Program (Program).
    (i) Incorporation by reference. (A) Subsection 20 of section 39.5 of 
the Environmental Protection Act adopted as Public Act 87-1213 signed 
into law on September 26, 1992, and effective upon signature.
    (B) Subsection 46.13(a) of the Civil Administrative Code adopted as 
Public Act 87-1177 signed into law on September 21, 1992, and effective 
upon signature.
    (ii) Other material. (A) Program description.
    (B) May 4, 1992, Interagency Agreement between DCCA and IEPA 
defining the responsibilities of each agency in developing and 
implementing the program.
    (97) On October 12, 1992, and June 2, 1993, the State of Illinois 
submitted a requested revision to the Illinois State Implementation Plan 
(SIP) intended to satisfy the requirements of section 182(a)(3)(B) of 
the Clean Air Act as amended in 1990. Included were State rules 
establishing procedures for the annual reporting of emissions of 
volatile organic material (VOM) and oxides of nitrogen (NOx) 
as well as other regulated air pollutants by stationary sources in ozone 
nonattainment areas. Also included was a June 2, 1993, commitment letter 
from the Illinois Environmental Protection Agency (IEPA) to fulfill the 
reporting requirements of the United States Environmental Protection 
Agency by performing the following tasks:
    (i) Update the AIRS Facility Subsystem using the annual emissions 
report data. The 1992 data will be updated by December 31, 1993, and 
subsequent updates will be made by July 1st of each year.
    (ii) Retain annual emissions reports for at least three (3) years.
    (iii) Develop and submit Emissions Statement Status Reports (ESSR) 
on a quarterly basis each year until all applicable sources have 
submitted the required annual emissions reports. The report will show 
the total number of facilities from which emission statement data was 
requested, the number of facilities that met the provisions, and the 
number of facilities that failed to meet the provisions. Sources that 
are delinquent in submitting their emissions statements will be 
individually listed if they emit 500 tons per year or more of VOM or 
2500 tons per year or more of NOx. The report will also 
contain the emission data requested in Appendix F of the July 6, 1992, 
Draft Guidance on the Implementation of an Emission Statement Program.
    (iv) All sources subject to the emission statement requirements must 
report, at a minimum, the information specified under subpart C of part 
254 of chapter II of subtitle B of title 35 of the Illinois 
Administrative Code.
    (A) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter II: 
Environmental Protection Agency, Part 254: Annual Emissions Report, 
adopted at 17 Illinois Register 7782, effective May 14, 1993.
    (B) Other material. June 2, 1993, commitment letter.
    (98) On July 21, 1986, the State a submitted revision to its 
particulate matter regulations to incorporate an emission limit for 
continuous automatic stoking animal pathological waste incinerators.
    (i) Incorporation by reference.
    (A) Title 35: Environmental Protection, Subtitle B: Air Pollution, 
Chapter 1: Pollution Control Board, Part 212 Visible and Particulate 
Matter Emissions, subpart D: Particulate Matter Emissions from 
Incinerators, section 212.185 Continuous Automatic Stoking Animal 
Pathological Waste Incinerators. Adopted December 18, 1986, added

[[Page 312]]

at 11 Ill. Reg. 1410, effective December 30, 1986.
    (99) On January 4, 1989, the State submitted revisions to its sulfur 
dioxide rules.
    (i) Incorporation by reference.
    (A) Title 35: Environmental Protection, Subtitle B: Air Pollution, 
Chapter 1: Pollution Control Board, Subchapter c: Emission Standards and 
Limitations for Stationary Sources, Part 214 Sulfur Limitations, Subpart 
A: General Provisions, section 214.102 Abbreviations and Units. Amended 
at 12 Ill. Reg. 20778, effective December 5, 1988.
    (B) Title 35: Environmental Protection, Subtitle B: Air Pollution, 
Chapter 1: Pollution Control Board, Subchapter c: Emission Standards and 
Limitations for Stationary Sources, Part 214 Sulfur Limitations, Subpart 
A: General Provisions, section 214.104 Incorporations by Reference. 
Amended at 15 Ill. Reg. 1017, effective January 15, 1991.
    (C) Title 35: Environmental Protection, Subtitle B: Air Pollution, 
Chapter 1: Pollution Control Board, Subchapter c: Emission Standards and 
Limitations for Stationary Sources, Part 214 Sulfur Limitations, Subpart 
O: Petroleum Refining, Petrochemical and Chemical Manufacturing, section 
214.382 Petroleum and Petrochemical Processes. Amended at 12 Ill. Reg. 
20778, effective December 5, 1988.
    (100) On October 21, 1993, the State submitted definitions codified 
as part of the Illinois Administrative Code for incorporation in the 
Illinois State Implementation Plan.
    (i) Incorporation by reference.
    Illinois Administrative Code Title 35: Environmental Protection, 
Subtitle B: Air Pollution, Chapter I: Pollution Control Board, 
Subchapter c: Emission Standards and Limitations for Stationary Sources, 
Part 211 Definitions and General Provisions, Subpart A: General 
Provisions: Sections 211.101 and 211.102, Subpart B: Definitions, 
Sections 211.121, 211.130, 211.150, 211.170, 211.210, 211.230, 211.250, 
211.290, 211.310, 211.330, 211.350, 211.370, 211.390, 211.410, 211.430, 
211.450, 211.470, 211.490, 211.510, 211.530, 211.550, 211.570, 211.590, 
211.610, 211.630, 211.650, 211.670, 211.690, 211.710, 211.730, 211.750, 
211.770, 211.790, 211.810, 211.830, 211.850, 211.870, 211.890, 211.910, 
211.930, 211.950, 211.970, 211.990, 211.1010, 211.1050, 211.1090, 
211.1110, 211.1130, 211.1150, 211.1170, 211.1190, 211.1210, 211.1230, 
211.1250, 211.1270, 211.1290, 211.1310, 211.1330, 211.1350, 211.1370, 
211.1390, 211.1410, 211.1430, 211.1470, 211.1490, 211.1510, 211.1530, 
211.1550, 211.1570, 211.1590, 211.1610, 211.1630, 211.1650, 211.1670, 
211.1690, 211.1710, 211.1730, 211.1750, 211.1770, 211.1790, 211.1810, 
211.1830, 211.1850, 211.1870, 211.1890, 211.1910, 211.1930, 211.1950, 
211.1970, 211.1990, 211.2010, 211.2050, 211.2070, 211.2090, 211.2110, 
211.2130, 211.2150, 211.2170, 211.2190, 211.2210, 211.2230, 211.2250, 
211.2270, 211.2310, 211.2330, 211.2350, 211.2370, 211.2390, 211.2410, 
211.2430, 211.2450, 211.2470, 211.2490, 211.2510, 211.2530, 211.2550, 
211.2570, 211.2590, 211.2650, 211.2670, 211.2690, 211.2710, 211.2730, 
211.2750, 211.2770, 211.2790, 211.2810, 211.2830, 211.2850, 211.2870, 
211.2890, 211.2910, 211.2930, 211.2950, 211.2970, 211.2990, 211.3010, 
211.3030, 211.3050, 211.3070, 211.3090, 211.3110, 211.3130, 211.3150, 
211.3170, 211.3190, 211.3210, 211.3230, 211.3250, 211.3270, 211.3290, 
211.3310, 211.3330, 211.3350, 211.3370, 211.3390, 211.3410, 211.3430, 
211.3450, 211.3470, 211.3490, 211.3510, 211.3530, 211.3550, 211.3570, 
211.3590, 211.3610, 211.3630, 211.3650, 211.3670, 211.3690, 211.3710, 
211.3730, 211.3750, 211.3770, 211.3790, 211.3810, 211.3830, 211.3850, 
211.3870, 211.3890, 211.3910, 211.3930, 211.3970, 211.3990, 211.4010, 
211.4030, 211.4050, 211.4070, 211.4090, 211.4110, 211.4130, 211.4150, 
211.4170, 211.4190, 211.4210, 211.4230, 211.4250, 211.4270, 211.4290, 
211.4310, 211.4330, 211.4350, 211.4370, 211.4390, 211.4410, 211.4430, 
211.4450, 211.4470, 211.4490, 211.4510, 211.4530, 211.4550, 211.4590, 
211.4610, 211.4630, 211.4650, 211.4670, 211.4690, 211.4710, 211.4730, 
211.4750, 211.4770, 211.4790, 211.4810, 211.4870, 211.4890, 211.4910, 
211.4930, 211.4950, 211.4990, 211.5030, 211.5050, 211.5070, 211.5090, 
211.5110, 211.5130, 211.5150, 211.5170, 211.5185, 211.5190, 211.5210, 
211.5230, 211.5250, 211.5270, 211.5310, 211.5330, 211.5350, 211.5370, 
211.5410, 211.5430, 211.5450, 211.5470, 211.5490, 211.5510, 211.5550, 
211.5570, 211.5590, 211.5610, 211.5630, 211.5650, 211.5670, 211.5690, 
211.5710, 211.5730, 211.5750, 211.5770, 211.5790, 211.5810, 211.5830, 
211.5850, 211.5870, 211.5890, 211.5910, 211.5930, 211.5950, 211.5970, 
211.5990, 211.6010, 211.6030, 211.6050,

[[Page 313]]

211.6070, 211.6090, 211.6130, 211.6150, 211.6190, 211.6210, 211.6230, 
211.6270, 211.6290, 211.6310, 211.6330, 211.6350, 211.6370, 211.6390, 
211.6410, 211.6430, 211.6450, 211.6470, 211.6490, 211.6510, 211.6530, 
211.6550, 211.6570, 211.6590, 211.6610, 211.6670, 211.6690, 211.6730, 
211.6750, 211.6770, 211.6790, 211.6810, 211.6850, 211.6870, 211.6890, 
211.6910, 211.6930, 211.6950, 211.6970, 211.6990, 211.7010, 211.7030, 
211.7070, 211.7090, 211.7110, 211.7130, 211.7150, 211.7170, 211.7190, 
211.7210, 211.7230, 211.7250, 211.7270, 211.7290, 211.7310, 211.7330, 
211.7350.
    These section were added at 17 Ill. Reg. 16504, effective September 
27, 1993.
    (101) On October 21, 1993, the state submitted volatile organic 
compound (VOC) control regulations for incorporation in the Illinois 
State Implementation for ozone.
    (i) Incorporation by reference.
    (A) Illinois Administrative Code Title 35: Environmental Protection, 
Subtitle B: Air Pollution, Chapter I: Pollution Control Board, 
Subchapter c: Emissions Standards and Limitations for Stationary 
Sources, Part 218: Organic Material Emission Standards and Limitations 
for the Chicago Area Subparts A, B, C, E, F, G, H, Q, R, S, T, V, W, X, 
Y, Z, AA, BB, and Section 218.
    Appendix A, B, C, and D. These regulations were adopted at R91-7 at 
15 Ill. Reg. 12231, effective August 16, 1991; amended in R91-23 at Ill. 
Reg. 13564, effective August 24, 1992; amended in R91-28 and R91-30 at 
16 Ill. Reg. 13864, effective August 24, 1992; amended in R93-9 at 17 
Ill. Reg. 16636, effective September 27, 1993. The specific adoption and 
effective dates of the rules incorporated by reference follow.
    (1) Adopted at R91-7 at 15 Ill. Reg. 12231, effective August 16, 
1991. Subpart A 218.108; Subpart C: 218.142; Subpart R: 218.442, 
218.444, 218.448, 218.451; Subpart T: 218.484, 218.488; Subpart V: 
218.526; Subpart X: 218.561, 218.563; Subpart Z: 218.607; Subpart AA: 
218.625, 218.626 and 218.630.
    (2) Amended in R93-9 at 17 Ill. Reg. 16636, effective September 27, 
1993. Subpart A: 218.100, 218.101, 218.102, 218.103, 218.104, 218.105, 
218.106, 218.107, 218.109, 218.110, 218.111, 218.112; Subpart B: 
218.121, 218.122, 218.123, 218.124; Subpart C: 218.141, 218.143, 
218.144; Subpart E: 218.181, 218.182, 218.183, 218.184, 218.186; Subpart 
F: 218.204, 218.205, 218.206, 218.207, 218.208, 218.209, 218.210, 
218.211; Subpart G: 218.301, 218.302, 218.303, 218.304; Subpart H: 
218.401, 218.402, 218.403, 218.404, 218.405; Subpart Q: 218.421, 
218.422, 218.423, 218.424, 218.425, 218.426, 218.427, 218.428, 218.429; 
Subpart R: 218.441, 218.443, 218.445, 218.446, 218.447, 218.449, 
218.450, 218.452; Subpart S: 218.461, 218.462, 218.463, 218.464; Subpart 
T: 218.480, 218.481, 218.482, 218.483, 218.485, 218.486, 218.487, 
218.489; Subpart V: 218.525; Subpart W: 218.541; Subpart X: 218.562; 
Subpart Y: 218.581, 218.582, 218.583, 218.584, 218.585, 218.586; Subpart 
Z: 218.601, 218.602, 218.603, 218.608, 218.609, 218.610, 218.611; 
Subpart AA: 218.620, 218.621, 218.623, 218.624, 218.628, 218.636, 
218.637; Subpart BB: 218.640, 218.642, 218.644, Section 218: Appendix A, 
Appendix B, Appendix C, Appendix D.
    (B) Illinois Administrative Code Title 35: Environmental Protection, 
Subtitle B: Air Pollution, Chapter I: Pollution Control Board, 
Subchapter c: Emissions Standards and Limitations for Stationary 
Sources, Part 219: Organic Material Emission Standards and Limitations 
for Metro East Area Subparts A, B, C, E, F, G, H, Q, R, S, T, V, W, X, 
Y, Z, AA, BB and Section 219 Appendix A, B, C, and D. These regulations 
were adopted at R91-8 at Ill. Reg. 12491, effective August 16, 1991; 
amended in R91-24 at 16 Ill. Reg. 13597, effective August 24, 1992; 
amended in R91-30 at 16 Ill. Reg. 13833, effective August 24, 1992, 
emergency amendment in R93-12 at Ill. Reg. 8295, effective May 24, 1993, 
for a maximum of 150 days, amended in R93-9 at 17 Ill. Reg. 16918, 
effective September 27, 1993 and October 21, 1993. The specific adoption 
and effective dates of the rules incorporated by reference follow.
    (1) Adopted at R91-8 at 15 Ill. Reg. 12491, effective August 16, 
1991: Subpart A: 219.103, 219.108; Subpart C: 219.142; Subpart R: 
219.442, 219.444, 219.448, 219.451; Subpart T: 219.484, 219.488; Subpart 
V: 219.526; Subpart X: 219.561, 219.563; Subpart Z: 219.607; Subpart AA: 
219.625, 219.626, 219.630.
    (2) Amended in R93-9 at 17 Ill. Reg. 16918, effective September 27, 
1993:
    Subpart A: 219.100, 219.101, 219.102, 219.104, 219.105, 219.106, 
219.107, 219.109, 219.110, 219.111, 219.112;

[[Page 314]]

    Subpart B: 219.121, 219.122, 219.123, 219.124;
    Subpart C: 219.141, 219.143, 219.144;
    Subpart E: 219.181, 219.182, 219.183, 219.184, 219.186;
    Subpart F: 219.204, 219.205, 219.206, 219.207, 219.208, 219.209, 
219.210, 219.211;
    Subpart G: 219.301, 219.302, 219.303, 219.304;
    Subpart H: 219.401, 219.402, 219.403, 219.404, 219.405;
    Subpart Q: 219.421, 219.422, 219.423, 219.424, 219.425, 219.426, 
219.427, 219.428, 219.429;
    Subpart R: 219.441, 219.443, 219.445, 219.446, 219.447, 219.449, 
219.450, 219.452;
    Subpart S: 219.461, 219.462, 219.463, 219.464;
    Subpart T: 219.480, 219.481, 219.482, 219.483, 219.485, 219.486, 
219.487, 219.489;
    Subpart V: 219.525;
    Subpart W: 219.541;
    Subpart X: 219.562;
    Subpart Y: 219.581, 219.582, 219.583, 219.584, 219.585, 219.586;
    Subpart Z: 219.601, 219.602, 219.603, 219.608, 219.609, 219.610, 
219.611;
    Subpart AA: 219.620, 219.621, 219.623, 219.624, 219.628, 219.636, 
219.637;
    Subpart BB: 219.640, 219.642, 219.644;
    Section 219: Appendix A, Appendix B, Appendix C, Appendix D.
    (102) On October 21, 1993 and March 4, 1994, the State submitted 
volatile organic compound control regulations for incorporation in the 
Illinois State Implementation Plan for ozone.
    (i) Incorporation by reference.
    (A) Title 35: Environmental Protection, Subtitle B: Air Pollution, 
Chapter I: Pollution Control Board, Subchapter c: Emission Standards and 
Limitations for Stationary Sources, Part 211: Definitions and General 
Provisions, Subpart B: Definitions, Sections 211.270, 211.1070, 
211.2030, 211.2610, 211.3950, 211.4050, 211.4830, 211.4850, 211.4970, 
211.5390, 211.5530, 211.6110, 211.6170, 211.6250, 211.6630, 211.6650, 
211.6710, 211.6830, 211.7050. These sections were adopted on January 6, 
1994, Amended at 18 Ill. Reg. 1253, and effective January 18, 1994.
    (B) Illinois Administrative Code Title 35: Environmental Protection, 
Subtitle B: Air Pollution, Chapter I: Pollution Control Board, 
Subchapter c: Emissions Standards and Limitations for Stationary 
Sources, Part 218: Organic Material Emissions Standards and Limitations 
for the Chicago Area, Subpart PP: 218.927, 218.928; Subpart QQ: 218.947, 
218.948; Subpart RR: 218.967, 218.968; Subpart TT: 218.987, 218.988; 
Subpart UU: 218.990. These sections were adopted on September 9, 1993, 
Amended at 17 Ill. Reg. 16636, effective September 27, 1993.
    (C) Illinois Administrative Code Title 35: Environmental Protection, 
Subtitle B: Air Pollution, Chapter I: Pollution Control Board, 
Subchapter c: Emissions Standards and Limitations for Stationary 
Sources, Part 218: Organic Material Emissions Standards and Limitations 
for the Chicago Area, Subpart A: 218.106, 218.108, 218.112, 218.114; 
Subpart H: 218.402; Subpart Z: 218.602, 218.611; Subpart AA: 218.620, 
218.623 (repealed); Subpart CC; Subpart DD; Subpart PP: 218.920, 
218.926; Subpart QQ: 218.940, 218.946; Subpart RR: 218.960, 218.966; 
Subpart TT: 218.980, 218.986; Subpart UU: 218.991. These sections were 
adopted on January 6, 1994, Amended at 18 Ill. Reg. 1945, effective 
January 24, 1994.
    (103) On February 11, 1993, Illinois submitted a site specific 
revision to its carbon monoxide State Implementation Plan for a General 
Motors Corporation iron foundry located adjacent to Interstate 74 at G 
Street in Vermilion County, Illinois.
    (i) Incorporation by reference.
    (A) Illinois Administrative Code; Title 35 Environmental Protection; 
Subtitle B: Air Pollution; Chapter I: Pollution Control Board; 
Subchapter C: Emission Standards and Limitations for Stationary Sources; 
P 216: Carbon Monoxide Emissions; Subpart O: Primary and Fabricated 
Metal Products; Section 216.382 Exception, General Motors Ferris Foundry 
in Vermilion County. Added at 16 Illinois Register 18075, effective 
November 13, 1992.
    (104)  [Reserved]
    (105) On February 7, 1994, the State submitted revisions intended to 
create a permit program for small sources. The purpose of these 
revisions is to lessen the permitting burden on small sources and the 
permitting authority by reducing the frequency and/or the requirement of 
operating permit renewal for sources emitting a total of less than 25 
tons per year of regulated

[[Page 315]]

air pollutants. A permit obtained through these procedures is intended 
to continue as a legally binding State document until the source 
modifies its operations, withdraws its permit or becomes subject to a 
new applicable requirement. At that time, the State will determine 
whether the small source procedures continue to be appropriate and issue 
a revised small source permit or direct the source in following the 
correct permit procedures. Since small source permits are not subject to 
a public comment period or review by USEPA, they are not federally 
enforceable and cannot be used to limit sources' potential to emit and 
thereby exempt them from the requirements of the title v operating 
permit program.
    (i) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board.
    (A) Subchapter a: Permits and General Provisions, Part 201: Permits 
and General Provisions.
    (1) Subpart D: Permit Applications and Review Process, Section 
201.162 Duration and Section 201.163 Joint Construction and Operating 
Permits. Amended at 17 Ill. Reg., effective December 7, 1993.
    (2) Subpart E: Special Provisions for Operating Permits for Certain 
Smaller Sources, Section 201.180 Applicability, Section 201.181 
Expiration and Renewal and Section 201.187 Requirement for a Revised 
Permit Added at 17 Ill. Reg., effective December 7, 1993.
    (B) Subchapter C: Emission Standards and Limitations for Stationary 
Sources, Part 211: Definitions and General Provisions, Subpart B: 
Definitions, Section 211.5500 Regulated Air Pollutant. Adopted at 17 
Ill. Reg., effective December 7, 1993.
    (106) On November 23, 1994, the State submitted amended marine 
vessel loading rules which consisted of revised definitions, and 
revisions to the Ozone Control Plan for the Chicago and Metro-East St. 
Louis areas.
    (i) Incorporation by reference.
    Illinois Administrative Code, Title 35: Environmental Protection, 
Subtitle B: Air Pollution, Chapter I: Pollution Control Board, 
Subchapter c: Emissions Standards and Limitations for Stationary 
Sources.
    (A) Part 211: Definitions and General Provisions, Subpart B: 
Definitions, Sections 211.3480 Loading Event and 211.3660 Marine Vessel 
added at 18 Ill. Reg. 166769, effective October 25, 1994; Sections 
211.3650 Marine Terminal, and 211.6970 Vapor Collection System, and 
Section 211.6990 Vapor Control System amended at 18 Ill. Reg. 16769, 
effective October 25, 1994.
    (B) Part 218: Organic Material Emission Standards and Limitations 
for the Chicago Area, Subpart A; General Provisions, Sections 218.101 
Savings Clause and 218.106 Compliance Dates amended at 18 Ill. Reg. 
16392, effective October 25, 1994; Subpart GG: Marine Terminals, 
Sections 218.760 Applicability, 218.762 Control Requirements, 218.764 
Compliance Certification, 218.766 Leaks, 218.768 Testing and Monitoring, 
and 218.770 Recordkeeping and Reporting added at 18 Ill. Reg. 16392, 
effective October 25, 1994; Appendix E: List of Affected Marine 
Terminals amended at 18 Ill. Reg. 16392, effective October 25, 1994.
    (C) Part 219: Organic Material Emissions Standards and Limitations 
for the Metro-East Area, Subpart A; General Provisions, Sections 219.101 
Savings Clause and 219.106 Compliance Dates amended at 18 Ill. Reg. 
16415, effective October 25, 1994; Subpart GG: Marine Terminals, 
Sections 219.760 Applicability, 219.762 Control Requirements, 219.764 
Compliance Certification, 219.766 Leaks, 219.768 Testing and Monitoring, 
and 219.770 Recordkeeping and Reporting added at 18 Ill. Reg. 16415, 
effective October 25, 1994.
    (D) Part 219: Organic Material Emissions Standards and Limitations 
for the Metro-East Area, Appendix E: List of affected Marine Terminals 
amended at 20 Ill. Reg. 3848. Effective February 15, 1996.
    (107) On October 25, 1994, Illinois submitted a regulation which 
requires gasoline dispensing operations in the Chicago and Metro-East 
St. Louis ozone nonattainment areas that have storage tanks of at least 
575 gallons to install pressure/vacuum relief valves on storage tank 
vent pipes. Tanks installed before January 1, 1979, are exempt from the 
rule if they have a capacity of less

[[Page 316]]

than 2000 gallons, as are tanks that are equipped with floating roofs or 
equivalent control devices that have been approved by the State and 
USEPA.
    (i) Incorporation by reference. Illinois Administrative Code Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board, Subchapter c: Emissions Standards and 
Limitations for Stationary Sources.
    (A) Part 201 Permits and General Provisions, Section 201.302 
Reports. Amended at 18 Ill. Reg. 15002. Effective September 21, 1994.
    (B) Part 211 Definitions and General Provisions, Section 211.5060 
Pressure/Vacuum Relief Valve. Added at 18 Ill. Reg. 14962. Effective 
September 21, 1994.
    (C) Part 218 Organic Material Emission Standards and Limitations for 
Chicago Area, Section 218.583 Gasoline Dispensing Operations-Storage 
Tank Filling Operations. Amended at 18 Ill. Reg. 14973. Effective 
September 21, 1994.
    (D) Part 219 Organic Material Emission Standards and Limitations for 
Metro East Area, Section 219.583 Gasoline Dispensing Operations-Storage 
Tank Filling Operations. Amended at 18 Ill. Reg. 14987. Effective 
September 21, 1994.
    (108) On January 25, 1994, the State submitted a revision to its 
ozone State Implementation Plan (SIP) for Quantum Chemical Corporation's 
facility located in Morris, Aux Sable Township, Grundy County, Illinois. 
It grants an adjusted standard from Parts 35 Illinois Administration 
Code (IAC) 218.966 and 218.986 as they apply to specific units or plants 
within this facility.
    (i) Incorporation by reference.
    (A) Illinois Pollution Control Board Final Opinion and Order, AS 92-
14, adopted on October 7, 1993, and effective on October 7, 1993.
    (109) On October 25, 1994, Illinois submitted a regulation that 
reduces the maximum allowable volatility for gasoline sold in the Metro-
East St. Louis ozone nonattainment area, which includes Madison, Monroe, 
and St. Clair Counties, to 7.2 pounds per square inch Reid Vapor 
Pressure (RVP) during the summer control period. On May 14, 1996, 
Illinois submitted an amendment to its RVP rule which changes the summer 
regulatory control period of the program. The summer control period for 
the Illinois RVP program is June 1 to September 15.
    (i) Incorporation by reference. Illinois Administrative Code Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board, Subchapter c: Emissions Standards and 
Limitations for Stationary Sources, Part 219 Organic Material Emission 
Standards and Limitations for Metro East Area.
    (A) Section 219.112 Incorporation by Reference. Amended at 18 Ill. 
Reg. 14987. Effective September 21, 1994.
    (B) [Reserved]
    (C) Section 219.585 Gasoline Volatility Standards. Amended at 20 
Ill. Reg. 3848: Effective February 15, 1996.
    (110) On September 26, 1994, the State of Illinois submitted a 
revision to its ozone State Implementation Plan for the J. M. Sweeney 
Company located in Cicero, Cook County, Illinois. It grants a compliance 
date extension from Stage II vapor control requirements (35 Ill. Adm. 
Code 218.586) from November 1, 1993, to March 31, 1995.
    (i) Incorporation by reference.
    (A) Illinois Pollution Control Board Final Opinion and Order, PCB 
93-257, adopted on September 1, 1994, and effective on September 1, 
1994. Certification dated 9/23/94 of Acceptance by J. M. Sweeney.
    (111) On July 29, 1994, Illinois submitted regulations which require 
adoption and implementation of particulate matter contingency measures 
for Illinois' four moderate particulate matter nonattainment areas. 
Sources in the nonattainment areas which emit at least 15 tons of 
particulate matter must submit two levels of contingency measures, which 
will then become Federally enforceable. Sources will be required to 
implement the contingency measures if an exceedance of the National 
Ambient Air Quality Standard for Particulate Matter is measured, or if 
the United States Environmental Protection Agency finds that an area has 
failed to attain the National Ambient Air Quality Standards.
    (i) Incorporation by reference.
    Illinois Administrative Code Title 35: Environmental Protection, 
Subtitle B: Air Pollution, Chapter I: Pollution Control Board;

[[Page 317]]

    (A) Part 106 Hearings Pursuant to Specific Rules, Section 106.930--
Applicability, Section 106.931--Petition for Review, Section 106.932--
Response and Reply, Section 106.933--Notice and Hearing, Section 
106.934--Opinion and Order. Amended at 18 Ill. Reg. 11579-11586. 
Effective July 11, 1994.
    (B) Part 212 Visible and Particulate Matter Emissions, Section 
212.700--Applicability, Section 212.701--Contingency Measure Plans, 
Submittal and Compliance Date, Section 212.702--Determination of 
Contributing Sources, Section 212.703--Contingency Measure Plan 
Elements, Section 212.704--Implementation, Section 212.705--Alternative 
Implementation. Added at 18 Ill. Reg. 11587-11606. Effective July 11, 
1994.
    (112) On March 28, 1995, the State of Illinois submitted a revision 
to its ozone State Implementation Plan for P & S, Incorporated's 
facility located in Wood Dale, Du Page County, Illinois. It grants a 
compliance date extension from Stage II vapor control requirements (35 
Ill. Adm. Code 218.586) from November 1, 1994 until April 1, 1996, or 60 
days after notification to P & S, Incorporated that the roadway 
construction complicating the installation of Stage II equipment will be 
abandoned for any reason, whichever is sooner.
    (i) Incorporation by reference.
    (A) Illinois Pollution Control Board Final Opinion and Order, PCB 
94-299, adopted on February 16, 1995, and effective on February 16, 
1995. Certification dated March 1, 1995 of Acceptance by P & S, 
Incorporated.
    (113) On April 27, 1995, the Illinois Environmental Protection 
Agency requested a revision to the Illinois State Implementation Plan in 
the form of revisions to the State's New Source Review rules for sources 
in the Chicago and metropolitan East St. Louis ozone nonattainment areas 
and are intended to satisfy Federal requirements of the Clean Air Act as 
amended in 1990. The State's New Source Review provisions are codified 
at Title 35: Environmental Protection Subtitle B: Air Pollution, Chapter 
I: Pollution Control Board, Subchapter a: Permits and General 
Provisions. Part 203 Major Stationary Sources Construction and 
Modification is amended as follows:
    (i) Incorporation by reference.
    (A) Title 35: Environmental Protection, Subpart A: General 
Provisions, Section 203.101 Definitions, Section 203.107 Allowable 
Emissions, Section 203.110 Available Growth Margin, Section 203.112 
Building, Structure and Facility, Section 203.121 Emission Offset, 
Section 203.122 Emissions Unit, Section 203.123 federally Enforceable, 
Section 203.126 Lowest Achievable Emission Rate, Section 203.128 
Potential to Emit, Section 203.145 Volatile Organic Material, Section 
203.150 Public Participation. Effective April 30, 1993.
    (B) Title 35: Environmental Protection, Subpart B: Major Stationary 
Sources in Nonattainment Areas, Section 203.201 Prohibition, Section 
203.203 Construction Permit Requirement and Application, Section 203.206 
Major Stationary Source, Section 203.207 Major Modification of a Source, 
Section 203.208 Net Emission Determination, Section 203.209 Significant 
Emissions Determination. Effective April 30, 1993.
    (C) Title 35: Environmental Protection, Subpart C: Requirements for 
Major Stationary Sources in Nonattainment Areas, Section 203.301 Lowest 
Achievable Emission Rate, Section 203.302 Maintenance of Reasonable 
Further Progress and Emission Offsets, Section 203.303 Baseline and 
Emission Offsets Determination, Section 203.306 Analysis of 
Alternatives. Effective April 30, 1993.
    (D) Title 35: Environmental Protection, Subpart H: Offsets for 
Emission Increases From Rocket Engines and Motor Firing, Section 203.801 
Offsetting by Alternative or Innovative Means. Effective April 30, 1993. 
Published in the Illinois Register, Volume 17, Issue 20, May 14, 1993.
    (114) On November 30, 1994, the State submitted an amended Synthetic 
Organic Chemical Manufacturing Industry Air Oxidation Process rule which 
consisted of extended applicability and tightened control measures to 
the Ozone Control Plan for the Chicago and Metro-East St. Louis areas.
    (i) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board, Subchapter c: Emissions Standards and 
Limitations for Stationary Sources.

[[Page 318]]

    (A) Part 218: Organic Material Emission Standards and Limitations 
for the Chicago Area, Subpart V; Air Oxidation Processes, Sections 
218.520 Emission Limitations for Air Oxidation Processes, 218.522 
Savings Clause, 218.523 Compliance, 218.524 Determination of 
Applicability, and 218.525 Emission Limitations for Air Oxidation 
Processes (Renumbered) at 18 Ill. Reg. 16972, effective November 15, 
1994.
    (B) Part 219: Organic Material Emissions Standards and Limitations 
for the Metro-East Area, Subpart V; Air Oxidation Processes, Sections 
219.520 Emission Limitations for Air Oxidation Processes, 219.522 
Savings Clause, 219.523 Compliance, 219.524 Determination of 
Applicability, and 219.525 Emission Limitations for Air Oxidation 
Processes (Renumbered) at 18 Ill. Reg. 17001, effective November 15, 
1994.
    (115) On May 5, 1995, and May 26, 1995, the State submitted an 
amended coating rule which consisted of a tightened applicability cut-
off level for wood furniture coating operations to the Ozone Control 
Plan for the Chicago and Metro-East St. Louis areas.
    (i) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board, Subchapter c: Emissions Standards and 
Limitations for Stationary Sources.
    (A) Part 218: Organic Material Emission Standards and Limitations 
for the Chicago Area, Subpart F; Coating Operations, Sections 218.208 
Exemptions from Emission Limitations, Subsection (b), amended at 19 Ill. 
Reg. 6848, effective May 9, 1995.
    (B) Part 219: Organic Material Emissions Standards and Limitations 
for the Metro-East Area, Subpart F; Coating Operations, Section 219.208 
Exemptions from Emission Limitations, Subsection (b), amended at 19 Ill. 
Reg. 6958, effective May 9, 1995.
    (116) On May 5, 1995, and May 26, 1995, the State submitted a rule 
for automotive/transportation and business machine plastic parts coating 
operations, which consisted of new volatile organic compound emission 
limitations to the Ozone Control Plan for the Chicago and Metro-East St. 
Louis areas.
    (i) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board, Subchapter c: Emissions Standards and 
Limitations for Stationary Sources.
    (A) Part 211: Definitions and General Provisions, Subpart B; 
Definitions, Sections 211.660 Automotive/Transportation Plastic Parts, 
211.670 Baked Coatings, 211.820 Business Machine Plastic Parts, 211.1880 
Electromagnetic Interference/Radio Frequency Interference Shielding 
Coatings, 211.1900 Electrostatic Prep Coat, 211.2360 Flexible Coatings, 
211.2630 Gloss Reducers, 211.4055 Non-Flexible Coating, 211.4740 Plastic 
Part, 211.5480 Reflective Argent Coating, 211.5600 Resist Coat, 211.6060 
Soft Coat, 211.6140 Specialty Coatings, 211.6400 Stencil Coat, 211.6580 
Texture Coat, and 211.6880 Vacuum Metallizing, amended at 19 Ill. 6823, 
effective May 9, 1995.
    (B) Part 218: Organic Material Emission Standards and Limitations 
for the Chicago Area, Subpart F; Coating Operations, Sections 218.204 
Emission Limitations, Subsection (n) Plastic Parts Coating: Automotive/
Transportation and (o) Plastic Parts Coating: Business Machine, 218.205 
Daily-Weighted Average Limitations, Subsection (g), and 218.207 
Alternative Emission Limitations, Subsection (i), amended at 19 Ill. 
6848, effective May 9, 1995.
    (C) Part 219: Organic Material Emissions Standards and Limitations 
for the Metro-East Area, Subpart F; Coating Operations, Section 219.204 
Emission Limitations, Subsection (m) Plastic Parts Coating: Automotive/
Transportation and (n) Plastic Parts Coating: Business Machine, 219.205 
Daily-Weighted Average Limitations, Subsection (f), and 219.207 
Alternative Emission Limitations, Subsection (h), amended at 19 Ill. 
Reg. 6958, effective May 9, 1995.
    (117) On May 31, 1995, the State submitted amended lithographic 
printing rules which consisted of revised definitions, and revisions to 
the Ozone Control Plan for the Chicago and Metro-East St. Louis areas.
    (i) Incorporation by reference.

[[Page 319]]

    Illinois Administrative Code, Title 35: Environmental Protection, 
Subtitle B: Air Pollution, Chapter I: Pollution Control Board, 
Subchapter c: Emissions Standards and Limitations for Stationary 
Sources.
    (A) Part 211: Definitions and General Provisions, Subpart B: 
Definitions, Sections 211.474 Alcohol, 211.560 As-Applied Fountain 
Solution, 211.2850 Heatset Web Offset Lithographic Printing Line, 
211.4065 Non-Heatset, 211.5980 Sheet-Fed added at 19 Ill. Reg. 6823, 
effective May 9, 1995.
    (B) Part 218: Organic Material Emission Standards and Limitations 
for the Chicago Area, Subpart H; Printing and Publishing, Sections 
218.405 Lithographic Printing: Applicability, 218.406 Provisions 
Applying to Heatset Web Offset Lithographic Printing Prior to March 15, 
1996, 218.407 Emissions Limitations and Control Requirements for 
Lithographic Printing Lines On and After March 15, 1996, 218.408 
Compliance Schedule for Lithographic Printing on and After March 15, 
1996, 218.409 Testing for Lithographic Printing On and After March 15, 
1996, 218.410 Monitoring Requirements for Lithographic Printing, 218.411 
Recordkeeping and Reporting for Lithographic Printing added at 19 Ill. 
Reg. 6848, effective May 9, 1995.
    (C) Part 219: Organic Material Emissions Standards and Limitations 
for the Metro-East Area, Subpart H; Printing and Publishing, Sections 
219.405 Lithographic Printing: Applicability, 219.406 Provisions 
Applying to Heatset Web Offset Lithographic Printing Prior to March 15, 
1996, 219.407 Emissions Limitations and Control Requirements for 
Lithographic Printing Lines On and After March 15, 1996, 219.408 
Compliance Schedule for Lithographic Printing on and After March 15, 
1996, 219.409 Testing for Lithographic Printing On and After March 15, 
1996, 219.410 Monitoring Requirements for Lithographic Printing, 219.411 
Recordkeeping and Reporting for Lithographic Printing added at 19 Ill. 
Reg. 6848, effective May 9, 1995.
    (118) On October 24, 1994, the State submitted a site-specific 
revision to the State Implementation Plan establishing lubricant 
selection and temperature control requirements for Alumax Incorporated, 
Morris, Illinois facility's hot and cold aluminum rolling mills, as part 
of the Ozone Control Plan for the Chicago area.
    (i) Incorporation by reference. September 1, 1994, Opinion and Order 
of the Illinois Pollution Control Board AS 92-13, effective September 1, 
1994.
    (119) On May 5, 1995, and May 26, 1995, the State submitted a 
revised rule tightening volatile organic compound emission limitations 
for certain surface coating operations in the Chicago and Metro-East St. 
Louis areas.
    (i) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board, Subchapter c: Emissions Standards and 
Limitations for Stationary Sources.
    (A) Part 218: Organic Material Emission Standards and Limitations 
for the Chicago Area, Subpart F; Coating Operations, Sections 218.204 
Emission Limitations, 218.205 Daily-Weighted Average Limitations, 
218.207 Alternative Emission Limitations, 218.208 Exemptions From 
Emission Limitations, 218.210 Compliance Schedule, 218.212 Cross-line 
Averaging to Establish Compliance for Coating Lines, 218.213 
Recordkeeping and Reporting for Cross-line Averaging Participating 
Coating Lines, 218.214 Changing Compliance Methods, 218 Appendix H 
Baseline VOM Content Limitations for Subpart F, Section 218.212 Cross-
Line Averaging, amended at 19 Ill. 6848, effective May 9, 1995.
    (B) Part 219: Organic Material Emissions Standards and Limitations 
for the Metro-East Area, Subpart F; Coating Operations, Sections 219.204 
Emission Limitations, 219.205 Daily-Weighted Average Limitations, 
219.207 Alternative Emission Limitations, 219.208 Exemptions From 
Emission Limitations, 219.210 Compliance Schedule, 219.212 Cross-line 
Averaging to Establish Compliance for Coating Lines, 219.213 
Recordkeeping and Reporting for Cross-line Averaging Participating 
Coating Lines, 219.214 Changing Compliance Methods, 219 Appendix H 
Baseline VOM Content Limitations for Subpart F, Section 219.212 Cross-
line Averaging, amended at 19 Ill. Reg. 6958, effective May 9, 1995.
    (120) On May 5, 1995, and May 31, 1995, the State of Illinois 
submitted a rule

[[Page 320]]

for motor vehicle refinishing operations, which consisted of new 
volatile organic material (VOM) emission limitations to the Ozone 
Control Plan for the Chicago and Metro East St. Louis areas. This State 
Implementation Plan revision contains rules which establish VOM content 
limits for certain coatings and surface preparation products used in 
automobile and mobile equipment refinishing operations in the Chicago 
and Metro-East area, as well as requires these operations to meet 
certain equipment and work practice standards to further reduce VOM.
    (i) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board, Subchapter c: Emissions Standards and 
Limitations for Stationary Sources.
    (A) Part 211: Definitions and General Provisions, Subpart B; 
Definitions, Sections 211.240 Adhesion Promoter, 211.495 Anti-Glare/
Safety Coating, 211.685 Basecoat/Clearcoat System, 211.1875 Elastomeric 
Materials, 211.3915 Mobile Equipment, 211.3960 Motor Vehicles, 211.3965 
Motor Vehicle Refinishing, 211.5010 Precoat, 211.5061 Pretreatment Wash 
Primer, 211.5080 Primer Sealer, 211.5090 Primer Surfacer Coat, 211.6145 
Specialty Coatings for Motor Vehicles, 211.6540 Surface Preparation 
Materials, 211.6620 Three or Four Stage Coating System, 211.6695 Topcoat 
System, 211.6720 Touch-Up Coating, 211.6860 Uniform Finish Blender, 
amended at 19 Ill. 6823, effective May 9, 1995.
    (B) Part 218: Organic Material Emission Standards and Limitations 
for the Chicago Area, Subpart HH; Motor Vehicle Refinishing, Sections 
218.780 Emission Limitations, 218.782 Alternative Control Requirements, 
218.784 Equipment Specifications, 218.786 Surface Preparation Materials, 
218.787 Work Practices, 218.788 Testing, 218.789 Monitoring and Record 
keeping for Control Devices, 218.790 General Record keeping and 
Reporting, 218.791 Compliance Date, 218.792 Registration, amended at 19 
Ill. 6848, effective May 9, 1995.
    (C) Part 219: Organic Material Emissions Standards and Limitations 
for the Metro-East Area, Subpart HH; Motor Vehicle Refinishing, Sections 
219.780 Emission Limitations, 219.782 Alternative Control Requirements, 
219.784 Equipment Specifications, 219.786 Surface Preparation Materials, 
219.787 Work Practices, 219.788 Testing, 219.789 Monitoring and Record 
keeping for Control Devices, 219.790 General Record keeping and 
Reporting, 219.791 Compliance Date 219.792 Registration, amended at 19 
Ill. Reg. 6958, effective May 9, 1995.
    (121) On May 23, 1995, and June 7, 1995, the State submitted 
volatile organic compound control regulations for incorporation in the 
Illinois State Implementation Plan for ozone.
    (i) Incorporation by reference.
    (A) Title 35: Environmental Protection, Subtitle B: Air Pollution, 
Chapter I: Pollution Control Board, Subchapter c: Emission Standards and 
Limitations for Stationary Sources, Part 211: Definitions and General 
Provisions, Subpart B: Definitions, Sections 211.695, 211.696, 211.5245, 
211.6025. These sections were adopted on May 4, 1995, Amended at 19 Ill. 
Reg. 7344, and effective May 22, 1995.
    (B) Title 35: Environmental Protection, Subtitle B: Air Pollution, 
Chapter I: Pollution Control Board, Subchapter c: Emission Standards and 
Limitations for Stationary Sources, Part 218: Organic Material Emission 
Standards and Limitations for the Chicago Area, Subpart V: 218.500, 
218.501, 218.502, 218.503, 218.504, 218.505, 218.506. These sections 
were adopted on May 4, 1995, Amended at 19 Ill. Reg. 7359, and effective 
May 22, 1995.
    (C) Title 35: Environmental Protection, Subtitle B: Air Pollution, 
Chapter I: Pollution Control Board, Subchapter c: Emission Standards and 
Limitations for Stationary Sources, Part 219: Organic Material Emission 
Standards and Limitations for the Metro East Area, Subpart V: 219.500, 
219.501, 219.502, 219.503, 219.504, 219.505, 219.506. These sections 
were adopted on May 4, 1995, Amended at 19 Ill. Reg. 7385, and effective 
May 22, 1995.
    (122) On June 26, 1995, the Illinois Environmental Protection Agency 
(IEPA) submitted a State Implementation Plan (SIP) revision containing 
the 1992 enhancements to the Illinois vehicle

[[Page 321]]

inspection and maintenance (I/M) program. Such enhancements were 
originally developed to meet the I/M performance standard as called for 
in the United States Environmental Protection Agency's (USEPA's) 
proposed `post-1987' I/M SIP policy and specified in the settlement 
agreement entered into by the parties in Wisconsin v. Reilly, Case No. 
87-C-0395, E.D. Wis. The submittal includes authorizing legislation P.A. 
86-1433, signed into law on September 12, 1990 and procedural rules 
published in the Illinois Register on June 26, 1992 at Volume 16, Issue 
#16.
    (i) Incorporation by reference.
    (A) 35 Illinois Administrative Code 276; Sections 276.101, 276.102, 
276.204, 276.206, 276.301, 276.303, 276.304, 276.307, 276.308, 276.309, 
276.310, 276.311, 276.401, 276.402, 276.701, 276.702, and 276.703 
amended or added at 16 Ill. Reg. 10230, effective June 15, 1992.
    (ii) Other material.
    (A) Public Act 86-1433 adopted by the Illinois General Assembly on 
June 29, 1990, signed into law by Governor Edgar on September 12, 1990 
effective September 12, 1990 (Sections 2,3, and 4) and January 1, 1991 
(Section 1). (B) June 26, 1995 letter and attachments from the IEPA's 
Bureau of Air Chief to the USEPA's Regional Air and Radiation Division 
Director submitting Illinois' revision to the ozone SIP.
    (123) On May 5, 1995, May 26, 1995, and May 31, 1995, the State of 
Illinois submitted miscellaneous revisions to its Volatile Organic 
Material (VOM) Reasonably Available Control Technology (RACT) rules 
contained in 35 Illinois Administrative Code Part 218: Organic Material 
Emission Standards and Limitations for the Chicago Area, and Part 219: 
Organic Material Emission Standards and Limitations for the Metro East 
Area. These amendments clarify certain applicability provisions, control 
requirements, and compliance dates contained within these regulations. 
Also included in these amendments is an exemption for certain 
polyethylene foam packaging operations from VOM RACT requirements.
    (i) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board, Subchapter c: Emission Standards and 
Limitations for Stationary Sources.
    (A) Part 218: Organic Material Emission Standards and Limitations 
for the Chicago Area, Subpart A: General Provisions, Section 218.106; 
Subpart T: Pharmaceutical Manufacturing, Section 218.480; Subpart DD: 
Aerosol Can Filling, Section 218.686; Subpart RR: Miscellaneous Organic 
Chemical Process, Section 218.966; Subpart TT: Other Emission Units, 
Section 218.980. Amended at 19 Ill. Reg. 6848; effective May 9, 1995.
    (B) Part 219: Organic Material Emission Standards and Limitations 
for the Metro East Area, Subpart T: Pharmaceutical Manufacturing, 
Section 219.480; Subpart TT: Other Emission Units, Section 219.980. 
Amended at 19 Ill. Reg. 6958, effective May 9, 1995.
    (124) The state of Illinois requested a revision to the Illinois 
State Implementation Plan (SIP). This revision is for the purpose of 
establishing and implementing a Clean-Fuel Fleet Program in the Chicago 
ozone nonattainment area, which includes Cook, DuPage, Grundy (Aux Sable 
and Goose Lake townships only), Kane, Kendall (Oswego township only), 
Lake, McHenry, and Will counties, to satisfy the federal requirements 
for a Clean Fuel Fleet Program to be part of the SIP for Illinois.
    (i) Incorporation by reference.
    (A) 35 Illinois Administrative Code 241; Sections 241.101, 241.102, 
241.103, 241.104, 241.110, 241.111, 241.112, 241.113, 241.114, 241.115, 
241.130, 241.131, 241.140, 241.141, 241.142, 241. Appendix A, 241. 
Appendix B adopted in R95-12 at 19 Ill. Reg. 13265, effective September 
11, 1995.
    (ii) Other material.
    (A) September 29, 1995 letter and attachments from the Illinois 
Environmental Protection Agency's Bureau of Air Chief to the USEPA's 
Regional Air and Radiation Division Director submitting Illinois' 
revision to the ozone SIP.
    (125) On November 14, 1995 the State submitted requested revisions 
to the Illinois State Implementation Plan in the form of revisions to 
the definitions of Organic Material and Organic Materials, Organic 
Solvent, Petroleum Liquid and Volatile Organic Material (VOM) or 
Volatile Organic Compound

[[Page 322]]

(VOC) intended to exempt acetone from regulation as a VOC.
    (i) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board, Subchapter c: Emission Standards and 
Limitations for Stationary Sources, Part 211: Definitions and General 
Provisions, Subpart B: Definitions, Section 211.4250 Organic Material 
and Organic Materials, Section 211.4260 Organic Solvent, Section 
211.4610 Petroleum Liquid, Section 211.7150 Volatile Organic Material 
(VOM) or Volatile Organic Compounds (VOC). Amended at 19 Ill. Reg. 
15176, effective October 19, 1995.
    (126) On November 15, 1995 the State submitted a requested revision 
to the Illinois State Implementation Plan in the form of a revision to 
the definition Volatile Organic Material (VOM) or Volatile Organic 
Compound (VOC) intended to exempt parachlorobenzotrifluoride and cyclic, 
branched or linear completely methylated siloxanes from the definition 
of VOM or VOC and thereby, from regulation as a VOC.
    (i) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board, Subchapter c: Emission Standards and 
Limitations for Stationary Sources, Part 211: Definitions and General 
Provisions, Subpart B: Definitions, Section 211.7150 Volatile Organic 
Material (VOM) or Volatile Organic Compounds (VOC). Amended at 19 Ill. 
Reg. 11066, effective July 12, 1995.
    (127) On October 21, 1993, and May 26, 1995, Illinois submitted 
volatile organic compound control regulations for incorporation in the 
Illinois State Implementation Plan for ozone.
    (i) Incorporation by reference.
    (A) Illinois Administrative Code Title 35: Environmental Protection, 
Subtitle B: Air Pollution, Chapter I: Pollution Control Board, 
Subchapter c: Emissions Standards and Limitations for Stationary 
Sources, Part 219: Organic Material Emissions Standards and Limitations 
for Metro East Area, Subpart PP: 219.920, 219.923, 219.927, 219.928; 
Subpart QQ: 219.940, 219.943, 219.947, 219.948; Subpart RR: 219.960, 
219.963, 219.967, 219.968; Subpart TT: 219.980, 219.983, 219.987, 
219.988; and Subpart UU. These Subparts were adopted on September 9, 
1993, Amended at 17 Ill. Reg. 16918, effective September 27, 1993.
    (B) Illinois Administrative Code Title 35: Environmental Protection, 
Subtitle B: Air Pollution, Chapter I: Pollution Control Board, 
Subchapter c: Emissions Standards and Limitations for Stationary 
Sources, Part 219: Organic Material Emissions Standards and Limitations 
for Metro East Area, Subpart PP: 219.926; Subpart QQ: 219.946; Subpart 
RR: 219.966; and Subpart TT: 219.986. These Subparts were adopted on 
April 20, 1995, Amended at 19 Ill. Reg. 6958, effective May 9, 1995.
    (128) On November 30, 1994, the State submitted volatile organic 
compound control regulations for incorporation in the Illinois State 
Implementation Plan for ozone.
    (i) Incorporation by reference.
    (A) Title 35: Environmental Protection, Subtitle B: Air Pollution, 
Chapter I: Pollution Control Board, Subchapter c: Emission Standards and 
Limitations for Stationary Sources, Part 211: Definitions and General 
Provisions, Subpart B: Definitions, Sections 211.2300, 211.3695. These 
sections were adopted on October 20, 1994, Amended at 18 Ill. Reg. 
16929, and effective November 15, 1994.
    (B) Title 35: Environmental Protection, Subtitle B: Air Pollution, 
Chapter I: Pollution Control Board, Subchapter c: Emission Standards and 
Limitations for Stationary Sources, Part 218: Organic Material Emission 
Standards and Limitations for the Chicago Area, Subpart B: 218.119, 
218.120, 218.125, 218.127, 218.128, 218.129. These sections were adopted 
on October 20, 1994, Amended at 18 Ill. Reg. 16950, and effective 
November 15, 1994.
    (C) Title 35: Environmental Protection, Subtitle B: Air Pollution, 
Chapter I: Pollution Control Board, Subchapter c: Emission Standards and 
Limitations for Stationary Sources, Part 219: Organic Material Emission 
Standards and Limitations for the Metro East Area, Subpart B: 219.119, 
219.120, 219.125, 219.127, 219.128, 219.129. These sections were adopted 
on October 20, 1994, Amended at 18 Ill. Reg. 16980, and effective 
November 15, 1994.

[[Page 323]]

    (129)  [Reserved]
    (130) On June 29, 1995, the State of Illinois submitted a revision 
to the State Implementation Plan (SIP) for the implementation of an 
enhanced motor vehicle inspection and maintenance (I/M) program in the 
Chicago and East St. Louis ozone nonattainment areas. This revision 
included the Vehicle Emissions Inspection Law of 1995 (625 ILCS 5/13B), 
P.A. 88-533, effective January 18, 1995; I/M regulations (R94-19 and 
R94-20) adopted on December 1, 1994, by the Illinois Pollution Control 
Board; February 29, 1996, Request-For-Proposals; April 22, 1996, letter 
of commitment; plus additional support documentation including modeling 
demonstration.
    (i) Incorporation by reference.
    (A) Vehicle Emissions Inspection Law of 1995 (625 ILCS 5/13B), 
Public Act 88-533, signed into law by Governor Edgar on January 18, 1995 
effective January 18, 1995.
    (B) 35 Illinois Administrative Code 240; Sections 240.101, 240.102, 
240.104, 240.105, 240.106, 240.107, 240.124, 240.125, 240.151, 240.152, 
240.153, 240.161, 240.162, 240.163, 240.164, 240.171, 240.Table A, 
240.Table B amended or added in R94-19 at 18 Ill. Reg. 18228, effective 
December 14, 1994.
    (C) 35 Illinois Administrative Code 240; Sections 240.172, 240.173 
amended in R94-20 at 18 Ill. Reg. 18013, effective December 12, 1994.
    (ii) Additional materials.
    (A) February 29, 1996, Request-For-Proposals submitted on April 22, 
1996.
    (B) April 22, 1996, letter of commitment and attachments from IEPA's 
Bureau of Air Chief to the USEPA's Regional Air and Radiation Division 
Director.
    (131) On January 10, 1996, the State of Illinois submitted a site-
specific State Implementation Plan (SIP) revision request for ozone, 
which extends the required deadline for the Rexam Medical Packaging Inc. 
facility in Mundelein, Lake County, Illinois (Rexam), to comply with 35 
Illinois Administrative Code, part 218, subpart H, as it applies to its 
Inline Press Number No.105, Inline Press No. 111, Offline 32-inch Press, 
Offline 36-inch Press, and Offline 42-inch press. The compliance date is 
extended from March 15, 1995, until June 15, 1996, or upon submittal of 
the ``certificate of compliance'' required under section 218.404 of 
subpart H, whichever occurs first. The variance includes a compliance 
plan requiring the installation and use of a catalytic oxidizer to 
control emissions from Inline Press No. 105, Inline Press No. 111, 
Offline 32-inch Press, and Offline 42-inch Press. The Offline 36-inch 
Press is required to convert to water-based ink, or be controlled by the 
oxidizer if the press is not converted by March 1, 1996. The variance is 
contingent upon certain compliance milestone conditions.
    (i) Incorporation by reference.
    (A) Illinois Pollution Control Board Final Opinion and Order, PCB 
95-99, adopted on October 19, 1995, and effective March 15, 1995. 
Certification of Acceptance dated November 29, 1996, by Rexam.
    (132) On January 8, 1996, Illinois submitted a site-specific 
revision to the State Implementation Plan establishing lubricant 
selection and temperature control requirements for the hot and cold 
aluminum operations at Reynolds Metals Company's McCook Sheet and Plate 
Plant in McCook, Illinois (in Cook County), as part of the Ozone Control 
Plan for the Chicago area.
    (i) Incorporation by reference. September 21, 1995, Opinion and 
Order of the Illinois Pollution Control Board AS 91-8, effective 
September 21, 1995.
    (133) On July 23, 1996, the Illinois Environmental Protection Agency 
submitted a site-specific State Implementation Plan revision request for 
the Chase Products Company's Broadview (Cook County), Illinois facility 
located at 19th Street and Gardner Road, as part of the Ozone Control 
Plan for the Chicago area. The resulting revision revises the control 
requirements codified at 35 Illinois Administrative Code Part 218 
Subpart DD Section 218.686 as they apply to the Chase Products Company's 
Broadview facility.
    (i) Incorporation by reference. May 16, 1996, Opinion and Order of 
the Illinois Pollution Control Board AS 94-4, effective May 16, 1996.
    (134) On May 5, 1995, and May 26, 1995, the State of Illinois 
submitted a State Implementation Plan revision request to the United 
States Environmental

[[Page 324]]

Protection Agency for reactor processes and distillation operation 
processes in the Synthetic Organic Chemical Manufacturing Industry as 
part of the State's control measures for Volatile Organic Material (VOM) 
emissions for the Chicago and Metro-East (East St. Louis) areas. VOM, as 
defined by the State of Illinois, is identical to ``volatile organic 
compounds'' (VOC), as defined by EPA. This plan was submitted to meet 
the Clean Air Act requirement for States to adopt Reasonably Available 
Control Technology rules for sources that are covered by Control 
Techniques Guideline documents. The EPA approves the State 
Implementation Plan revision request as it applies to Stepan Company's 
Millsdale Facility.
    (i) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board, Subchapter c: Emissions Standards and 
Limitations for Stationary Sources.
    (A) Part 211: Definitions and General Provisions, Subpart B; 
Definitions, 211.980 Chemical Manufacturing Process Unit, 211.1780 
Distillation Unit, 211.2365 Flexible Operation Unit, 211.5065 Primary 
Product.
    (B) Part 218: Organic Material Emission Standards and Limitations 
for the Chicago Area, Subpart Q: Synthetic Organic Chemical and Polymer 
Manufacturing Plant, Sections 218.431 Applicability, 218.432 Control 
Requirements, 218.433 Performance and Testing Requirements, 218.434 
Monitoring Requirements, 218.435 Recordkeeping and Reporting 
Requirements, 218.436 Compliance Date, 218 Appendix G, TRE Index 
Measurement for SOCMI Reactors and Distillation Units, amended at 19 
Ill. Reg. 6848, effective May 9, 1995.
    (135) On January 23, 1996, Illinois submitted a site-specific 
revision to the State Implementation Plan which relaxes the volatile 
organic material (VOM) content limit for fabricated product adhesive 
operations at Solar Corporation's Libertyville, Illinois facility from 
3.5 pounds VOM per gallon to 5.75 pounds VOM per gallon.
    (i) Incorporation by reference. July 20, 1995, Opinion and Order of 
the Illinois Pollution Control Board, AS 94-2, effective July 20, 1995.
    (136) On January 9, 1997, Illinois submitted a site-specific 
revision to the State Implementation Plan which grants a temporary 
variance from certain automotive plastic parts coating volatile organic 
material requirements at Solar Corporation's Libertyville, Illinois 
facility.
    (i) Incorporation by reference. September 5, 1996, Opinion and Order 
of the Illinois Pollution Control Board, PCB 96-239, effective September 
13, 1996. Certificate of Acceptance signed September 13, 1996.
    (137) Approval--On April 25, 1997, the Illinois Environmental 
Protection Agency submitted a revision to the State Implementation Plan 
for general conformity rules. The general conformity rules enable the 
State of Illinois to implement the general conformity requirements in 
the nonattainment or maintenance areas at the State or local level in 
accordance with 40 CFR part 93, subpart B--Determining Conformity of 
General Federal Actions to State or Federal Implementation Plans.
    (i) Incorporation by reference.
    (A) Illinois Administrative Code, Title 35: Environmental 
Protection, Subtitle B: Air Pollution, Chapter 2: Environmental 
Protection Agency, Part 255 General Conformity: Criteria and Procedures. 
Adopted at 21 Ill. Reg. effective March 6, 1997.
    (138) On May 5, 1995, and May 26, 1995, the State of Illinois 
submitted State Implementation Plan (SIP) revision requests for reactor 
processes and distillation operation processes in the Synthetic Organic 
Chemical Manufacturing Industry as part of the State's control measures 
for Volatile Organic Material emissions for the Metro-East (East St. 
Louis) area. This State Implementation Plan revision request is approved 
as it applies to Monsanto Chemical Group's Sauget Facility.
    (i) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board, Subchapter c: Emissions Standards and 
Limitations for Stationary Sources.

[[Page 325]]

    (A) Part 211: Definitions and General Provisions, Subpart B; 
Definitions, 211.980 Chemical Manufacturing Process Unit, 211.1780 
Distillation Unit, 211.2365 Flexible Operation Unit, 211.5065 Primary 
Product, amended at 19 Ill. Reg. 6823, effective May 9, 1995.
    (B) Part 219: Organic Material Emission Standards and Limitations 
for the Metro East Area, Subpart Q: Synthetic Organic Chemical and 
Polymer Manufacturing Plant, Sections 219.431 Applicability, 219.432 
Control Requirements, 219.433 Performance and Testing Requirements, 
219.434 Monitoring Requirements, 219.435 Recordkeeping and Reporting 
Requirements, 219.436 Compliance Date, 219.Appendix G, TRE Index 
Measurement for SOCMI Reactors and Distillation Units, amended at 19 
Ill. Reg. 6958, effective May 9, 1995.
    (139) On September 8, 1997, the State of Illinois submitted 
tightened volatile organic material rules for cold cleaning degreasing 
operations in the Chicago and the Metro-East ozone nonattainment areas.
    (i) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board, Subchapter c: Emissions Standards and 
Limitations for Stationary Sources.
    (A) Part 211: Definitions and General Provisions, Subpart B: 
Definitions, Section 211.1885, amended at 21 Ill. 7695, effective June 
9, 1997.
    (B) Part 218: Organic Material Emission Standards and Limitations 
for the Chicago Area, Subpart E: Solvent Cleaning, Section 218.182, 
amended at 21 Ill. 7708, effective June 9, 1997.
    (C) Part 219: Organic Material Emissions Standards and Limitations 
for the Metro-East Area, Subpart E: Solvent Cleaning, Section 219.182, 
amended at 21 Ill. 7721, effective June 9, 1997.
    (140) On March 5, 1998, the State of Illinois submitted amended 
rules for the control of volatile organic material emissions from wood 
furniture coating operations in the Chicago and Metro-East (East St. 
Louis) ozone nonattainment areas, as a requested revision to the ozone 
State Implementation Plan. This plan was submitted to meet the Clean Air 
Act requirement for States to adopt Reasonably Available Control 
Technology rules for sources that are covered by Control Techniques 
Guideline documents.
    (i) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board, Subchapter c: Emissions Standards and 
Limitations for Stationary Sources.
    (A) Part 211: Definitions and General Provisions, Subpart B; 
Definitions, 211.1467 Continuous Coater, 211.1520 Conventional Air 
Spray, 211.6420 Strippable Spray Booth Coating, 211.7200 Washoff 
Operations, amended at 22 Ill. Reg. 3497, effective February 2, 1998.
    (B) Part 218: Organic Material Emission Standards and Limitations 
for the Chicago Area, Subpart F: Coating Operations 218.204 Emission 
Limitations, 218.205 Daily-weighted Average Limitations, 218.210 
Compliance Schedule, 218.211 Recordkeeping and Reporting, 218.215 Wood 
Furniture Coating Averaging Approach, 218.216 Wood Furniture Coating 
Add-On Control Use, 218.217 Wood Furniture Coating Work Practice 
Standards, amended at 22 Ill. Reg. 3556, effective February 2, 1998.
    (C) Part 219: Organic Material Emission Standards and Limitations 
for the Metro East Area, Subpart F: Coating Operations 219.204 Emission 
Limitations, 219.205 Daily-weighted Average Limitations, 219.210 
Compliance Schedule, 219.211 Recordkeeping and Reporting, 219.215 Wood 
Furniture Coating Averaging Approach, 219.216 Wood Furniture Coating 
Add-On Control Use, 219.217 Wood Furniture Coating Work Practice 
Standards, amended at 22 Ill. Reg. 3517, effective February 2, 1998.
    (141) On November 14, 1995, May 9, 1996, June 14, 1996, and February 
3, 1997, October 16, 1997, and October 21, 1997, the State of Illinois 
submitted State Implementation Plan (SIP) revision requests to meet 
commitments related to the conditional approval of Illinois' May 15, 
1992, SIP submittal for the Lake Calumet (SE Chicago), McCook, and 
Granite City, Illinois, Particulate Matter (PM) nonattainment areas. The 
EPA is approving the portion of the SIP revision request that applies to 
the Granite City area. The SIP revision request corrects, for the 
Granite City PM

[[Page 326]]

nonattainment area, all of the deficiencies of the May 15, 1992, 
submittal.
    (i) Incorporation by reference. (A) Illinois Administrative Code 
Title 35: Environmental Protection, Subtitle B: Air Pollution, Chapter 
1: Pollution Control Board, Subchapter c: Emission Standards and 
Limitations for Stationary Sources, Part 212: Visible and Particulate 
Matter Emissions, Subpart A: General, Sections 212.107, 212.108, 
212.109, 212.110; Subpart L: Particulate Matter from Process Emission 
Sources, Section 212.324; Subpart N: Food Manufacturing, Section 
212.362; Subpart Q: Stone, Clay, Glass and Concrete Manufacturing, 
Section 212.425; Subpart R: Primary and Fabricated Metal Products and 
Machinery Manufacture, Sections 212.446, 212.458; Subpart S: 
Agriculture, Section 212.464. Adopted at 20 Illinois Register 7605, 
effective May 22, 1996.
    (B) Joint Construction and Operating Permit: Application Number 
95010005, Issued on October 21, 1997, to Granite City Division of 
National Steel Corporation.
    (142) On May 5, 1995, and May 26, 1995, the State of Illinois 
submitted State Implementation Plan revision requests for reactor 
processes and distillation operations in the Synthetic Organic Chemical 
Manufacturing Industry as part of the State's control measures for 
Volatile Organic Material emissions for the Chicago and Metro-East (East 
St. Louis) areas. This plan was submitted to meet the Clean Air Act 
requirement for States to adopt Reasonably Available Control Technology 
rules for sources that are covered by Control Techniques Guideline 
documents.
    (i) Incorporation by reference. Illinois Administrative Code, Title 
35: Environmental Protection, Subtitle B: Air Pollution, Chapter I: 
Pollution Control Board, Subchapter c: Emissions Standards and 
Limitations for Stationary Sources.
    (A) Part 211: Definitions and General Provisions, Subpart B; 
Definitions, 211.980 Chemical Manufacturing Process Unit, 211.1780 
Distillation Unit, 211.2365 Flexible Operation Unit, 211.5065 Primary 
Product, amended at 19 Ill. Reg. 6823, effective May 9, 1995.
    (B) Part 218: Organic Material Emission Standards and Limitations 
for the Chicago Area, Subpart Q: Synthetic Organic Chemical and Polymer 
Manufacturing Plant, Sections 218.431 Applicability, 218.432 Control 
Requirements, 218.433 Performance and Testing Requirements, 218.434 
Monitoring Requirements, 218.435 Recordkeeping and Reporting 
Requirements, 218.436 Compliance Date, 218.Appendix G, TRE Index 
Measurement for SOCMI Reactors and Distillation Units, amended at 19 
Ill. Reg. 6848, effective May 9, 1995.
    (C) Part 219: Organic Material Emission Standards and Limitations 
for the Metro East Area, Subpart Q: Synthetic Organic Chemical and 
Polymer Manufacturing Plant, Sections 219.431 Applicability, 219.432 
Control Requirements, 219.433 Performance and Testing Requirements, 
219.434 Monitoring Requirements, 219.435 Recordkeeping and Reporting 
Requirements, 219.436 Compliance Date, 219.Appendix G, TRE Index 
Measurement for SOCMI Reactors and Distillation Units, amended at 19 
Ill. Reg. 6958, effective May 9, 1995.
[37 FR 10862, May 31, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.720, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.

    Effective Date Note:  At 63 FR 27492, May 19, 1998, Sec. 52.720 was 
amended by adding paragraph (c)(140), effective July 20, 1998.



Sec. 52.721  Classification of regions.

    The Illinois plan was evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                                  Pollutant
                                                           -----------------------------------------------------
                Air quality control region                  Particulate   Sulfur   Nitrogen   Carbon
                                                               matter     oxides    dioxide  monoxide    Ozone
----------------------------------------------------------------------------------------------------------------
Burlington-Keokuk Interstate..............................           I          I       III       III        III
East Central Illinois Intrastate..........................         III         II       III       III        III
Metropolitan Chicago Interstate (Indiana-Illinois)........           I          I         I         I          I
Metropolitan Dubuque Interstate...........................           I        III       III       III        III
Metropolitan Quad Cities Interstate.......................           I        III       III       III        III
Metropolitan St. Louis Interstate (Missouri-Illinois).....           I          I       III         I          I

[[Page 327]]

North Central Illinois Intrastate.........................          II         IA       III       III        III
Paducah (Kentucky)-Cairo (Illinois) Interstate............           I         II       III       III        III
Rockford (Illinois)-Janesville-Beloit (Wisconsin)
 Interstate...............................................          II        III       III       III        III
Southeast Illinois Intrastate.............................         III         II       III       III        III
West Central Illinois Intrastate..........................           I         IA       III       III        III
----------------------------------------------------------------------------------------------------------------

[37 FR 10862, May 31, 1972, as amended at 39 FR 16346, May 8, 1974; 45 
FR 11493, Feb. 21, 1980]



Sec. 52.722  Approval status.

    (a) With the exceptions set forth in this subpart, the Administrator 
approved Illinois' plan for the attainment and maintenance of the 
National Ambient Air Quality Standards under section 110 of the Clean 
Air Act. Furthermore, the Administrator finds the plan satisfies all 
requirements of part D, title I of the Clean Air Act as amended in 1977, 
except as noted below. In addition, continued satisfaction of the 
requirements of part D for the ozone portion of the SIP depends on the 
adoption and submittal of RACT requirements by July 1, 1980, for the 
sources covered by CTGs between January 1978 and January 1979 and 
adoption and submittal by each subsequent January of additional RACT 
requirements for sources covered by CTGs issued by the previous January.
    (b) The Administrator finds that the transportation control plans 
for the East St. Louis and Chicago areas submitted on December 3, 1982, 
satisfy the related requirements of part D, title I of the Clean Air 
Act, as amended in 1977.
    (c) The Administrator finds that the carbon monoxide control 
strategy submitted on May 4, 1983, satisfies all requirements of part D, 
title I of the Clean Air Act, as amended in 1977, except for section 
172(b)(6).
[55 FR 40661, Oct. 4, 1990]



Sec. 52.723  [Reserved]



Sec. 52.724  Control strategy: Sulfur dioxide.

    (a) Part D--Conditional Approval--The Illinois plan is approved 
provided that the following condition is satisfied:
    (1) The plan includes a reanalysis of the Pekin, Illinois area, a 
submittal of the analysis results to USEPA, the proposal of any 
additional regulations to the Illinois Pollution Control Board necessary 
to insure attainment and maintenance of the sulfur dioxide standard, and 
the promulgation of any necessary regulations. The State must complete 
the reanalysis, submit the results to USEPA and submit any necessary, 
additional regulations to the Illinois Pollution Control Board by 
September 30, 1980. Any necessary regulation must be finally promulgated 
by the State and submitted to USEPA by September 30, 1981.
    (2) Extension of Condition--USEPA approves the date of July 1, 1984 
for submitting the draft sulfur dioxide rule revisions and supporting 
documentation as required in (a)(1) for Peoria, Hollis and Groveland 
Townships in Illinois. The State must complete final rule adoption as 
expeditiously as possible but no later than December 31, 1985.
    (b) Part D--Disapproval--USEPA disapproves Rules 204(c)(1)(B), Rule 
204(c)(1)(C), Rule 204(e)(1) and Rule 204(e)(2) for those sources for 
which these rules represent a relaxation of the federally enforceable 
State Implementation Plan. Rule 204(c)(1)(B), Rule 204(c)(1)(C), Rule 
204(e)(1) and Rule 204(e)(2) are approved as not representing 
relaxations of the State Implementation Plan for the following sources:

[[Page 328]]



   Sources of 10 Million Btu per Hour or More Not Increasing Allowable Sulfur Dioxide Emissions as a Result of
 Record Rules 204(c) and 204(e) Because New Allowable Emissions Rate is Same as or Less Than Old Allowable Rate
                                    Pounds per Hour (Pounds per Million Btu)
----------------------------------------------------------------------------------------------------------------
                                                                                                  Emissions now
                                                                                    Emissions       allowable
                   County                                    Name                    formerly      without new
                                                                                  allowable \1\       permit
                                                                                                 application \2\
----------------------------------------------------------------------------------------------------------------
Boone......................................  Chrysler...........................    1,760 (4.4)     1,760 (4.4)
Champaign..................................  Chanute Air Base...................    1,317 (3.0)     1,317 (3.0)
Crawford...................................  CIPS...............................    8,242 (5.1)     8,242 (5.1)
Douglas....................................  USI Chemicals......................    8,022 (5.3)     8,022 (5.3)
Fulton.....................................  Freeman Coal.......................     22.2 (1.2)      22.2 (1.2)
La Salle...................................  Del Monte..........................      296 (3.9)       296 (3.9)
Massac.....................................  EEI Joppa..........................   36,865 (3.6)    36,865 (3.6)
Montgomery.................................  CIPS...............................   55,555 (5.8)    55,555 (5.8)
Morgan.....................................  ......do...........................   24,000 (6.0)    20,800 (5.2)
Putnam.....................................  Illinois Power.....................   17,051 (5.8)    17,051 (5.8)
Randolph...................................  ......do \3\.......................   81,339 (4.6)    81,339 (4.6)
Rock Island................................  International Harvester............   1,643 (4.35)    1,643 (4.35)
Williamson.................................  Marion Correctional................      396 (5.7)       396 (5.7)
----------------------------------------------------------------------------------------------------------------
\1\ 6.0 lbs/MMBTU of existing coal fired capacity or total 204(e)(2) emissions less actual oil fired and NSPS
  emissions, whichever is lower.
\2\ Maximum allowable emissions for existing coal fired capacity according to revised rules 204(c) and 204(e)
  consolidated, usually equally equalling total emissions as given by 204(e)(2) less actual oil fired NSPS
  emissions. (In the one case wherein the new allowable limit is less than that given by 204(e)(2) the allowable
  emissions were determined by 204(e)(1) with which the source is required to comply.)
\3\ Source is in compliance per 204(e)(3).
CIPS=Central Illinois Public Service.
EEI=Electric Energy Incorporated.


This disapproval does not in and of itself result in the growth 
restrictions of section 110(a)(2)(1).
    (c) Disapproval--USEPA disapproves Rule 204(e)(4) as not being 
adequate to protect the NAAQS. This disapproval does not in and of 
itself result in the growth restrictions of section 110(a)(2)(I).
    (d) Disapproval--USEPA disapproves Rule 204(f)(1)(D) as completely 
deregulating SO2 emissions from existing processes without 
providing an assessment of the ambient air quality impact or a showing 
that increasing the allowable emissions from these sources will not 
cause or contribute to violations of the NAAQS or PSD increments. This 
disapproval does not in and of itself result in the growth restrictions 
of section 110(a)(2)(I).
    (e) Disapproval--USEPA disapproves Rule 204(h) for those sources for 
which USEPA has disapproved rules 204(c) and 204(e). This disapproval 
does not in and of itself result in the growth restrictions of section 
110(a)(2)(I).
    (f) Approval--USEPA approves rule 204(e)(3) for those sources able 
to show that the proposed emission rate will not cause or contribute to 
a violation of the NAAQS. The State must submit these emission 
limitations, along with the technical support to USEPA for approval.
    (g) Part D--Approval--The State plan for Alton Township, Madison 
County, which consists of a federally Enforceable State Operating Permit 
controlling sulfur dioxide emissions from the boilers and reheat 
furnaces at Laclede Steel, which was submitted on November 18, 1993, is 
approved.
    (h) Approval--On November 10, 1994, the Illinois Environmental 
Protection Agency submitted a sulfur dioxide redesignation request and 
maintenance plan for Peoria and Hollis Townships in Peoria County and 
Groveland Township in Tazewell County to redesignate the townships to 
attainment for sulfur dioxide. The redesignation request and maintenance 
plan meet the redesignation requirements in section 107(d)(3)(d) of the 
Clean Air Act (Act) as amended in 1990.
[45 FR 62806, 62809, Sept. 22, 1980, as amended at 50 FR 5250, Feb. 7, 
1985; 59 FR 18753, Apr. 20, 1994; 60 FR 17001, Apr. 4, 1995]



Sec. 52.725  Control strategy: Particulates.

    (a) [Reserved]

[[Page 329]]

    (b) Part D--Disapproval. (1) U.S. EPA disapproves the provisions of 
Rule 203(f) which allow the use of an equivalent method without review 
and approval of that method. Any source subject to Rule 203(f) which 
chooses to use an equivalent method must have that equivalent method 
submitted to U.S. EPA and approved as a SIP revision.
    (2) U.S. EPA disapproves the following portions of Rule 203(d)(5) 
which regulate the control of particulate matter from specific sources 
within the iron and steel industry: Rule 205(d)(5)(B)(ii), Rule 
205(d)(5)(B)(iii), Rule 205(d)(5)(D), and Rule 205(d)(5)(K).
    (3) USEPA disapproves a proposed SIP revision submitted by the State 
on May 12, 1982, in the form of a May 18, 1981 Consent Decree (Civil 
Action 81-3009) to which USEPA, Illinois Environmental Protection Agency 
and National Steel Corporation are parties and a draft Alternative 
Control Strategy Permit. This submission was modified by the State, 
September 30, 1982, with the submission of a separate document embodying 
the elements of the Alternative Control Strategy. This separate document 
was intended to become an enforceable part of the SIP.
    (c) Approval--On September 28, 1988, the State of Illinois submitted 
a committal SIP for particulate matter with an aerodynamic diameter 
equal to or less than 10 micrometers (PM10) for the Illinois 
Group II areas of concern in DuPage, Will, Rock Island, Macon, Randolph, 
and St. Clair Counties. The committal SIP contains all the requirements 
identified in the July 1, 1987, promulgation of the SIP requirements for 
PM10 at 52 FR 24681.
    (d) Approval--On June 2, 1995, and January 9, 1996, the State of 
Illinois submitted a maintenance plan for the particulate matter 
nonattainment portion of LaSalle County, and requested that it be 
redesignated to attainment of the National Ambient Air Quality Standard 
for particulate matter. The redesignation request and maintenance plan 
satisfy all applicable requirements of the Clean Air Act.
    (e) Approval--On March 19, 1996, and October 15, 1996, Illinois 
submitted requests to redesignate the Granite City Particulate Matter 
(PM) nonattainment area to attainment status for the PM National Ambient 
Air Quality Standards (NAAQS), as well as a maintenance plan for the 
Granite City area to ensure continued attainment of the NAAQS. The 
redesignation request and maintenance plan satisfy all applicable 
requirements of the Clean Air Act.
[45 FR 11493, Feb. 21, 1980, as amended at 46 FR 44185, Sept. 3, 1981; 
47 FR 26620, June 21, 1982; 48 FR 45246, Oct. 4, 1983; 49 FR 1905, Jan. 
16, 1984; 55 FR 20266, May 16, 1990; 61 FR 41345, Aug. 8, 1996; 63 FR 
11846, Mar. 11, 1998]



Sec. 52.726  Control strategy: Ozone.

    (a) Part D--Conditional Approval--The Illinois plan is approved 
provided that the following conditions are satisfied:
    (1) [Reserved]
    (2) The State conducts a study to demonstrate that the 75 percent 
overall control efficiency requirement in Rule 205(n) represents RACT, 
submits the results of the study to USEPA, and submits any necessary 
regulations representing RACT to the Illinois Pollution Control Board. 
The State must comply with these conditions by February 28, 1981. Any 
necessary regulations must be finally promulgated by the State and 
submitted to USEPA by February 28, 1982.
    (3) Extension of Condition--USEPA approves the date of July 31, 1984 
for the State of Illinois to satisfy the condition of approval to the 
ozone State Implementation Plan listed in paragraph (a)(2) of this 
section.
    (b) Disapproval--USEPA disapproves the compliance schedule in Rule 
205(j) as it applies to loading rack controls for all emission sources 
subject to Rule 205(b)(1), as approved by USEPA on May 31, 1972 which 
were required to be in compliance by December 31, 1973. This disapproval 
does not in and of itself result in the growth restrictions of section 
110(a)(2)(I).
    (c) Negative Declarations--Stationary Source Categories. The State 
of Illinois has certified to the satisfaction of USEPA that no sources 
are located in the nonattainment areas of the State which are covered by 
the following Control Technique Guidelines:
    (1) High density polyethylene and polypropylene manufacturers.

[[Page 330]]

    (2) Vegetable oil processing sources with volatile organic compound 
emissions equal to or greater than 100 tons per year.
    (d) Part D Disapproval--The Administrator finds that Illinois' ozone 
plan for Cook, Lake, DuPage and Kane Counties, which was required to be 
submitted by July 1, 1982, does not satisfy all the requirements of Part 
D, Title I of the Clean Air Act and, thus, is disapproved. No major new 
stationary source, of major modification of a stationary source, or 
volatile organic compounds may be constructed in Cook, Lake, DuPage or 
Kane Counties, unless the construction permit application is complete on 
or before November 16, 1988. This disapproval does not affect USEPA's 
approval (or conditional approval) of individual parts of Illinois' 
ozone plan, and they remain approved.
    (e) Disapproval--The Administrator finds that the following State 
rules have not been demonstrated to be consistent with the reasonably 
available control technology requirements of section 172 of the Clean 
Air Act, as amended in 1977, and thus, are disapproved: subpart F, 
section 215.204(c); subpart F, section 215.206(b); subpart F, section 
215.204(j)(4); subpart I; subpart AA; subpart PP; subpart QQ; subpart 
RR; subpart A, section 215.102; subpart T; subpart H, section 215.245; 
subpart F, section 215.207; and subpart A, section 215.107, all of title 
35; Environmental Protection; subtitle B: Air Pollution; Chapter 1: 
Pollution Control Board of the Illinois Administrative Code (June 1989).
    (f) On September 30, 1992, the State submitted rules regulating 
volatile organic compound emissions from gasoline dispensing facilities' 
motor vehicle fuel operations (Stage II vapor recovery rules) in the 
Chicago ozone nonattainment area. The Illinois Environmental Protection 
Agency Bureau of Air must as part of the program conduct inspections of 
facilities subject to this rule to ensure compliance with the applicable 
rules. These inspections will be conducted on an annual basis or an 
alternative schedule as approved in the USEPA Fiscal Year Inspection 
Program Plan.
    (g) Approval--The Administrator approves the incorporation of the 
photochemical assessment ambient monitoring system submitted by Illinois 
on November 4, 1993, into the Illinois State Implementation Plan. This 
submittal satisfies 40 CFR 58.20(f) which requires the State to provide 
for the establishment and maintenance of photochemical assessment 
monitoring stations (PAMS) by November 12, 1993.
    (h) Approval--On November 12, 1993, the Illinois Environmental 
Protection Agency submitted an ozone redesignation request and 
maintenance plan for Jersey County ozone nonattainment area and 
requested that Jersey County be redesignated to attainment for ozone. 
The redesignation request and maintenance plan meet the redesignation 
requirements in section 107(d)(3)(d) of the Act. The redesignation meets 
the Federal requirements of section 182(a)(1) of the Clean Air Act as a 
revision to the Illinois ozone State Implementation Plan for Jersey 
County.
    (i) The base year (1990) ozone emission inventory requirement of 
section 182(a)(1) of the Clean Air Act, as amended in 1990, has been 
satisfied for the following Illinois ozone nonattainment areas: the 
Chicago nonattainment area--Cook, DuPage, Kane, Lake, Will and McHenry 
Counties, Aux Sable and Gooselake Townships in Grundy County, and Oswego 
Township in Kendall County; the Metro-East St. Louis nonattainment 
area--Madison, Monroe, and St. Clair Counties; and Jersey County.
    (j) Approval--On July 14, 1994, Illinois submitted two of three 
elements required by section 182(d)(1)(A) of the Clean Air Amendments of 
1990 to be incorporated as part of the vehicle miles traveled (VMT) 
State Implementation Plan intended to offset any growth in emissions 
from a growth in vehicle miles traveled. These elements are the 
offsetting of growth in emissions attributable to growth in VMT which 
was due November 15, 1992, and, transportation control measures (TCMs) 
required as part of Illinois' 15 percent reasonable further progress 
(RFP) plan which was due November 15, 1993. Illinois satisfied the first 
requirement by projecting emissions from mobile sources and 
demonstrating that no increase in emissions would take place.

[[Page 331]]

Illinois satisfied the second requirement by submitting the TCMs listed 
in Table 1 which are now approved into the Illinois SIP.

                                                     Table 1
----------------------------------------------------------------------------------------------------------------
                                                                                                          SIP
             Project type                       Location description              Completion status      credit
                                                                                                        VOC tpd
----------------------------------------------------------------------------------------------------------------
RS/SIG MOD...........................  Madison Street (Western Ave. to         Done..................   0.015400
                                        Halsted Street).
SIG COORD............................  Willow Road (Landwer Road to Shermer).  Awarded...............   0.052000
SIG COORD............................  Rand Road (Baldwin Road to Kennicott).  Awarded...............   0.052000
SIG COORD............................  Northwest Hwy (Potter Road to           Awarded...............   0.030000
                                        Cumberland Avenue).
SIGS/SIG COORD.......................  159th Street (US 45 to 76th Ave & at    Awarded...............   0.030000
                                        91st Avenue).
SIG COORD............................  Harlem Ave. (71st St. to 92nd)........  Awarded...............   0.052000
SIG COORD............................  Harlem Ave. (99th Street to 135th St.)  Awarded...............   0.052000
RECONST/SIGS/LTS.....................  Archer Ave. (88th Ave to 65th St.)....  Awarded...............   0.030000
SIG COORD............................  Ogden Ave. (N. Aurora Road to Naper     Awarded...............   0.030000
                                        Boulevard).
SIG COORD............................  North Ave. (Tyler to Kautz)...........  Awarded...............   0.030000
SIG COORD............................  Higgens Road (Il 72 at Il 31).........  Awarded...............   0.030000
SIG COORD............................  Sheridan Road (Il 173 to Wadsworth)...  Awarded...............   0.030000
SIG COORD............................  Lagrange Road (Belmont to Lake St.)...  Awarded...............   0.030000
SIG COORD............................  Dundee Road (Sanders Road to Skokie     Awarded...............   0.052000
                                        Valley Road).
SIG COORD............................  Dundee Road (Buffalo Grove Road to Il   Awarded...............   0.030000
                                        21).
INT IMP/SIG COORD....................  Golf Road (E. River Road to Washington  Awarded...............   0.052000
                                        Ave.).
SIG COORD............................  Golf Road (Barrington to Roselle Road)  Awarded...............   0.030000
SIG COORD............................  Higgins Road (Barrington to Roselle     Awarded...............   0.030000
                                        Road).
SIG COORD............................  Joe Orr Road (Vincennes Ave. to Il 1).  Awarded...............   0.030000
----------------------------------------------------------------------------------------------------------------


                                                     Table 1
----------------------------------------------------------------------------------------------------------------
             Project type                         Location description            Completion status   SIP credit
----------------------------------------------------------------------------------------------------------------
SIG COORD/RS..........................  Crawford Ave. (93rd Street to 127th      Awarded                0.052000
                                         Street).
SIG COORD.............................  IL 53 (Briarcliff to South of I-55)....  Done                   0.030000
SIG COORD.............................  Ogden Ave. (Oakwood Avenue to Fairview   Awarded                0.019000
                                         Avenue).
SIG COORD.............................  US 14 (Rohlwing Road to Wilke Road)....  Awarded                0.030000
SIG COORD.............................  US 30 (At Cottage Grove, Ellis St).....  Awarded                0.030000
SIG COORD.............................  IL 53 (Modonough to Mills).............  Done                   0.030000
SIG CONN..............................  Ogden Ave. (IL 43 to 31st Street)......  Awarded                0.013000
SIG CONN..............................  US 12 (Long Grove--Hicks Road).........  Awarded                0.055200
SIG CONN..............................  North Ave. (Oak Park to Ridgeland).....  Awarded                0.007000
SIG CONN..............................  Roosevelt Road (Westchester Bl--IL 43).  Awarded                0.137000
SIG CONN..............................  Depster St (Keeler to Crawford Ave.)...  Awarded                0.010000
SIG CONN..............................  Arlington Hgts Rd. (Thomas to Central).  Awarded                0.044000
SIG CONN..............................  Palatine Rd. (Shoenbeck to Wolf Roads).  Awarded                0.042500
SIG CONN..............................  Western Ave. (US 30--Lakewood).........  Awarded                0.018900
RS/INT IMP............................  North Ave. (I-290 to IL 43)............  Awarded                0.056100
INT IMP...............................  Plum Grove Rd. (At Higgins Road).......  Awarded                0.010700
INT IMP...............................  St Street (At Illinois)................  Awarded                0.002700
RS/SIG MOD/INT IMP....................  Illinois/Grand (Kingsbury to Lake Shore  Done                   0.004200
                                         Drive).
ADD TURN LANES........................  York Rd. (Industrial to Grand Ave.)....  Done                   0.003800
SERVICE IMP...........................  SW Route Lane Service..................  Scheduled              0.005516
SIG INTCONN...........................  Washington Street......................  Scheduled              0.030370
SIG INTCONN...........................  IL 59..................................  Scheduled              0.068650
ENGR..................................  Citywide--Naperville...................  ...................    0.086230
SIG INTCONN...........................  Washington Street......................  Scheduled              0.008230
SIG INTCONN...........................  Lewis Ave. (Yorkhousse to ILL 173).....  Scheduled              0.034600
SIG INTCONN...........................  Schaumberg Rd. (Barrington to            Scheduled              0.078080
                                         Martingale).
Vanpool Program (94 vehicles).........  Region-Wide Suburban...................  Done                   0.134000
Transp. Center........................  North West Cook County.................  Done                   0.032835
Transp. Center........................  Sears T.F..............................  Done                   0.005805
Station...............................  Clark/Lake.............................  Done                   0.010000
Station Recon.........................  18 Th Douglas Line.....................  Done                   0.001500
Station Recon.........................  Linden.................................  Done                   0.001500
Station Recon.........................  Cottage Grove..........................  Done                   0.001300
Com. Pkg..............................  Lisle..................................  Done                   0.010177
Com. Pkg..............................  Jefferson Park.........................  Done                   0.000110
Com. Pkg..............................  Edison Park............................  Done                   0.003614
Com. Pkg..............................  Palatine...............................  Done                   0.004336
Com. Pkg..............................  Central Street.........................  Done                   0.000519
Com. Pkg..............................  Palatine...............................  Done                   0.004890
Com. Pkg..............................  Crystal Lake...........................  Done                   0.034948
Com. Pkg..............................  137Th/Riverdale........................  Done                   0.004565
Com. Pkg..............................  River Forest...........................  Done                   0.000289

[[Page 332]]

Com. Pkg..............................  115Th/Kensington.......................  Done                   0.002795
Com. Pkg..............................  119Th St...............................  Done                   0.004483
Com. Pkg..............................  Wilmette...............................  Done                   0.001587
Com. Pkg..............................  111Th St...............................  Done                   0.000507
Com. Pkg..............................  Edison Park............................  Done                   0.002371
Com. Pkg..............................  Joliet.................................  Done                   0.003967
Com. Pkg..............................  Hanover Park...........................  Done                   0.021799
Com. Pkg..............................  Bartlett...............................  Done                   0.008911
Com. Pkg..............................  Chicago Ridge..........................  Done                   0.002159
Com. Pkg..............................  103 Rd St..............................  Done                   0.000675
Com. Pkg..............................  Elmhurst...............................  Done                   0.003857
Com. Pkg..............................  Bartlett...............................  Done                   0.009326
Com. Pkg..............................  Morton Grove...........................  Done                   0.001444
Com. Pkg..............................  Palatine...............................  Done                   0.003598
Com. Pkg..............................  Harvard................................  Done                   0.006299
Com. Pkg..............................  Willow Springs.........................  Done                   0.001200
Com. Pkg..............................  Edgebrook..............................  Done                   0.002240
Com. Pkg..............................  Bensenville............................  Done                   0.002010
Com. Pkg..............................  Hanover Park...........................  Done                   0.015020
Com. Pkg..............................  Midlothian.............................  Done                   0.002570
Com. Pkg..............................  Route 59...............................  Done                   0.025020
Com. Pkg..............................  Lake Forest (West).....................  Done                   0.013780
Com. Pkg..............................  Lombard................................  Done                 ..........
Com. Pkg..............................  Elmhurst...............................  Done                   0.001010
Com. Pkg..............................  Woodstock..............................  Done                   0.019000
Com. Pkg..............................  University Park........................  Done                   0.019950
Com. Pkg..............................  Grayslake..............................  Done                   0.006210
Com. Pkg..............................  Oak Forest.............................  Done                   0.004260
Com. Pkg..............................  91 St St...............................  Done                   0.003380
Com. Pkg..............................  Lockport...............................  Done                   0.007360
Com. Pkg..............................  Ravenswood.............................  Done                   0.000130
Com. Pkg..............................  Hickory Creek..........................  Done                   0.060140
Com. Pkg..............................  Cary...................................  Done                   0.005980
Com. Pkg..............................  Blue Island............................  Done                   0.019430
Com. Pkg..............................  Lemont.................................  Done                   0.016200
Com. Pkg..............................  Itasca.................................  Done                   0.003860
Com. Pkg..............................  Maywood................................  Done                   0.000600
Com. Pkg..............................  Ivanhoe................................  Done                   0.001960
Com. Pkg..............................  Ravinia................................  Done                   0.003210
Com. Pkg..............................  Fox River Grove........................  Done                   0.025170
Com. Pkg..............................  Medinah................................  Done                   0.012250
Com. Pkg..............................  Hanover Park...........................  Done                   0.011840
Com. Pkg..............................  Worth..................................  Done                   0.003530
Com. Pkg..............................  Roselle................................  Done                   0.007710
Com. Pkg..............................  Crystal Lake...........................  Done                   0.015050
Com. Pkg..............................  Gresham................................  Done                   0.000300
Com. Pkg..............................  Barrington.............................  Done                   0.002420
Rideshare Prog........................  Regionwide.............................  Scheduled              0.040000
Rapid Transit Service.................  Midway Airport.........................  Done                   0.220000
Transp. Center........................  Deerfield Lake-Cook....................  Done                   0.004160
Station Recon.........................  Davis St...............................  Done                   0.004000
Station Recon.........................  Addison................................  Done                   0.004000
Station Recon.........................  King Drive.............................  Done                   0.003000
Station Recon.........................  Washington/Wells.......................  Done                   0.003000
Com. Pkg..............................  Cary...................................  Done                   0.027910
Com. Pkg..............................  Morton Grove...........................  Done                   0.002460
Com. Pkg..............................  80th Ave...............................  Scheduled              0.043200
Com. Pkg..............................  Round Lake.............................  Done                   0.015150
Com. Pkg..............................  Grayslake..............................  Done                   0.009170
Com. Pkg..............................  Ingleside..............................  Scheduled              0.005430
Com. Pkg..............................  Schamburg..............................  Scheduled              0.042090
Com. Pkg..............................  Oak Forest.............................  Scheduled              0.004680
Com. Pkg..............................  Lake Cook..............................  Scheduled              0.026390
Com. Pkg..............................  Grayslake..............................  Scheduled              0.035290
----------------------------------------------------------------------------------------------------------------

    (k) Approval--EPA is approving the section 182(f) oxides of nitrogen 
(NOX) reasonably available control technology (RACT), new 
source review

[[Page 333]]

(NSR), vehicle inspection/maintenance (I/M), and general conformity 
exemptions for the Illinois portion of the Chicago-Gary-Lake County 
severe ozone nonattainment area as requested by the States of Illinois, 
Indiana, Michigan, and Wisconsin in a July 13, 1994 submittal. This 
approval does not cover the exemption of NOX transportation 
conformity requirements of section 176(c) for this area. Approval of 
these exemptions is contingent on the results of the final ozone 
attainment demonstration expected to be submitted in mid-1997. The 
approval will be modified if the final attainment demonstration 
demonstrates that NOX emission controls are needed in the 
nonattainment area to attain the ozone standard in the Lake Michigan 
Ozone Study modeling domain.
    (l) Approval--The United States Environmental Protection Agency is 
approving under section 182(b)(1) of the Clean Air Act the exemption of 
the Chicago severe, ozone nonattainment area from the build/no-build and 
less than-1990 interim transportation conformity oxides of nitrogen 
requirements as requested by the State of Illinois in a June 20, 1995 
submittal. In light of the modeling completed thus far and considering 
the importance of the OTAG process and attainment plan modeling efforts, 
USEPA grants this NOX waiver on a contingent basis. As the 
OTAG modeling results and control recommendations are completed in 1996, 
this information will be incorporated into attainment plans being 
developed by the LADCO States. When these attainment plans are submitted 
to USEPA in mid-1997, these new modeling analyses will be reviewed to 
determine if the NOX waiver should be continued, altered, or 
removed. USEPA's rulemaking action to reconsider the initial 
NOX waiver may occur simultaneously with rulemaking action on 
the attainment plans. The USEPA also reserves the right to require 
NOX emission controls for transportation sources under 
section 110(a)(2)(D) of the Act if future ozone modeling demonstrates 
that such controls are needed to achieve the ozone standard in downwind 
areas. The Chicago severe ozone nonattainment area includes the Counties 
of Cook, DuPage, Grundy (Aux Sable and Gooselake Townships), Kane, 
Kendall (Oswego Township), Lake, McHenry, and Will.
    (m) On June 29, 1995, and April 22, 1996, the Illinois Environmental 
Protection Agency (IEPA) submitted enhanced inspection and maintenance 
(I/M) legislation, rules, and a Request-For-Proposal (RFP) as a revision 
to the State's ozone State Implementation Plan (SIP). The EPA 
conditionally approved the SIP revision based on the State's commitment 
to submit to EPA the signed enhanced I/M contract, in addition to 
provide appropriate analyses, calculations, and rules necessary to 
address deficiencies noted in the final conditional approval. The final 
signed contract and any supporting documentation needed to address the 
deficiencies must be submitted to EPA within one year of the EPA's 
conditional approval.
    (n) Negative declaration-- Shipbuilding and ship repair industry. On 
October 11, 1996, the State of Illinois certified to the satisfaction of 
the United States Environmental Protection Agency that no major sources 
categorized as part of the shipbuilding and ship repair industry are 
located in the Chicago, Illinois ozone nonattainment area which is 
comprised of Cook, DuPage, Kane, Lake, McHenry, Will Counties and Aux 
Sable and Goose Lake Townships in Grundy County and Oswego Township in 
Kendall County or the Metro-East, Illinois ozone nonattainment area 
which is comprised of Madison, Monroe, and St. Clair Counties.
    (o) Negative declaration-- Aerospace manufacturing and rework 
industry. On October 11, 1996, the State of Illinois certified to the 
satisfaction of the United States Environmental Protection Agency that 
no major sources categorized as part of the Aerospace Manufacturing and 
Rework Industry are located in the Chicago, Illinois ozone nonattainment 
area which is comprised of Cook, DuPage, Kane, Lake, McHenry, Will 
Counties and Aux Sable and Goose Lake Townships in Grundy County and 
Oswego Township in Kendall County or the Metro-East, Illinois ozone 
nonattainment area which is comprised of Madison, Monroe, and St. Clair 
Counties.

[[Page 334]]

    (p) Approval--On November 15, 1993, Illinois submitted 15 percent 
rate-of-progress and 3 percent contingency plans for the Chicago ozone 
nonattainment area as a requested revision to the Illinois State 
Implementation Plan. These plans satisfy sections 182(b)(1), 172(c)(9), 
and 182(c)(9) of the Clean Air Act, as amended in 1990.
    (q) Approval--On November 15, 1993, Illinois submitted 15 percent 
rate-of-progress and 3 percent contingency plans for the Metro-East St. 
Louis ozone nonattainment area as a requested revision to the Illinois 
State Implementation Plan. These plans satisfy sections 182(b)(1) and 
172(c)(9) of the Clean Air Act, as amended in 1990.
    (r) Approval--On November 15, 1993, Illinois submitted the following 
transportation control measures as part of the 15 percent rate-of-
progress and 3 percent contingency plans for the Metro-East ozone 
nonattainment area: Work trip reductions; transit improvements; and 
traffic flow improvements.
    (s) On October 10, 1997, Illinois submitted a site-specific revision 
to the State Implementation Plan, in the form of a letter from Bharat 
Mathur, Chief, Bureau of Air, Illinois Environmental Protection Agency. 
This October 10, 1997, letter requests a change in regulatory status for 
Riverside Laboratories, Inc.'s Kane County facility, to reflect that the 
Federal site-specific rule for Riverside (40 CFR 52.741(e)(10)) has been 
superseded by the State of Illinois regulations, including the emission 
limits in 35 Illinois Administrative Code 218.204(c) and the associated 
control requirements, test methods and recordkeeping requirements in 
Part 218 and the associated definitions in part 211. These State 
regulations shall become the federally approved regulations applicable 
to Riverside on August 31, 1998. The site-specific rule, applicable to 
Riverside, promulgated by the Environmental Protection Agency on August 
21, 1995 (40 CFR 52.741(e)(10)), remains in effect and is enforceable 
after August 31, 1998 for the period before August 31, 1998.
[45 FR 55197, Aug. 19, 1980]

    Editorial Note:  For Federal Register citations affecting 
Sec. 52.726, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.

    Effective Date Note:  At 63 FR 35844, July 1, 1998, Sec. 52.726 was 
amended by adding paragraph (s), effective Aug. 31, 1998.



Sec. 52.727  [Reserved]



Sec. 52.728  Control strategy: Nitrogen dioxide.   [Reserved]



Sec. 52.729  Control strategy: Carbon monoxide.

    The following source specific emission controls are approved:
    (a) Approval--On August 15, 1996, the Illinois Environmental 
Protection Agency requested that the Marathon Oil Company in Robinson, 
Illinois be granted a carbon monoxide (CO) state implementation plan 
(SIP) revision with specified conditions. This SIP revision limits the 
Marathon Oil Company's CO emissions from its fluid bed catalytic 
cracking unit CO boiler to be no more than 300 parts per million of CO 
corrected for 50 percent excess air beginning January 19, 1996, and 
ending August 4, 1997. The variance became effective January 19, 1996. 
The SIP revision request satisfies all applicable requirements of the 
Clean Air Act.
    (b) [Reserved]
[62 FR 16705, Apr. 8, 1997]



Sec. 52.730  Compliance schedules.

    (a) The requirements of Sec. 51.262(a) of this chapter are not met 
since compliance schedules with adequate increments of progress have not 
been submitted for every source for which they are required.
    (b) Federal compliance schedules. (1) Except as provided in 
paragraph (b)(3) of this section, the owner or operator of any 
stationary source subject to the following emission limiting regulations 
in the Illinois implementation plan shall comply with the applicable 
compliance schedule in paragraph (b)(2) of this section: Illinois Air 
Pollution Control Regulations Rule 203(d)(4), 203(d)(6)(B)(ii)(bb), 
203(g)(1)(B), 203(g)(2), 203(g)(3), 203(g)(4), 204(c)(1)(A), 204(c)(2), 
204(d), and 204(e).
    (2) Compliance schedules. (i) The owner or operator of any 
stationary source subject to Illinois Air Pollution Control Regulation 
Rule 203(d)(4) shall take the following actions with respect to the 
source no later than the date specified.

[[Page 335]]

    (a) September 30, 1973--Advertise for bids for purchase and 
construction or installation of equipment, or for materials requisite 
for process modification sufficient to control particulate emissions 
from the source.
    (b) November 15, 1973--Award contracts for emission control systems 
or process modification, or issue orders for the purchase of component 
parts to accomplish emission control or process modification.
    (c) May 31, 1974--Initiate onsite construction or installation of 
emission control system or process modification.
    (d) March 31, 1975--Complete onsite construction or installation of 
emission system or process modification.
    (e) May 31, 1975--Complete shakedown operation and performance test 
on source, submit performance test results to the Administrator; achieve 
full compliance with State agency regulation.
    (ii) The owner or operator of any stationary source subject to 
Illinois Air Pollution Control Regulation Rule 203(d)(6)(B)(ii)(bb) 
shall take the following actions with respect to the source no later 
than the date specified.
    (a) September 30, 1973--Advertise for bids for purchase and 
construction or for modification of equipment sufficient to control 
particulate emissions from the source.
    (b) November 15, 1973--Award contracts for emissions control systems 
or process modification, or issue orders for the purchase of component 
parts to accomplish emission control or process modification.
    (c) March 31, 1974--Initiate onsite construction or installation of 
emission control system.
    (d) October 31, 1974--Complete onsite construction or installation 
of emission control system.
    (e) December 31, 1974--Achieve final compliance with Illinois Air 
Pollution Control Regulations Rule 203(d)(6)(B)(ii)(bb).
    (iii) (a) The owner or operator of any boiler or furnace of more 
than 250 million BTU per hour heat input subject to Illinois Air 
Pollution Control Regulation Rule 204(c)(1)(A), 204(c)(2), 204(d), and 
204(e) shall notify the Administrator, no later than October 1, 1973, of 
his intent to utilize either low-sulfur fuel or stack gas 
desulfurization to the requirements of said regulation.
    (b) Any owner or operator of a stationary source subject to 
paragraph (b)(2)(iii)(a) of this section who elects to utilize low 
sulfur fuel shall take the following actions with respect to the source 
no later than the date specified.
    (1) November 1, 1973--Submit to the Administrator a projection of 
the amount of fuel, by types, that will be substantially adequate to 
enable compliance with Illinois Air Pollution Control Regulations Rule 
204(c)(1)(A), 204(c)(2), 204(d), and 204(e) on May 31, 1975, and for at 
least one year thereafter.
    (2) December 31, 1973--Sign contracts with fuel suppliers for fuel 
requirements as projected above.
    (3) January 31, 1974--Submit a statement as to whether boiler 
modifications will be required. If modifications will be required, 
submit plans for such modifications.
    (4) March 15, 1974--Let contracts for necessary boiler 
modifications, if applicable.
    (5) June 15, 1974--Initiate onsite modifications, if applicable.
    (6) March 31, 1975--Complete onsite modifications, if applicable.
    (7) May 31, 1975--Final compliance with the emission limitation of 
Rules 204(c)(1)(A), 204(c)(2), 204(d), and 204(e).
    (c) Any owner or operator of a fuel combustion source subject to 
paragraph (b)(2)(iii)(a) of this section who elects to utilize stack gas 
desulfurization shall take the following actions with respect to the 
source no later than the date specified.
    (1) November 1, 1973--Let necessary contracts for construction.
    (2) March 31, 1974--Initiate onsite construction.
    (3) March 31, 1975--Complete onsite construction.
    (4) May 31, 1975--Complete shakedown operations and performance test 
on source, submit performance test results to the Administrator; achieve 
full compliance with Rule 204(c)(1)(A), 204(c)(2), 204(d), and 204(e).
    (iv) (a) The owner or operator of any stationary source subject to 
Illinois Air Pollution Control Regulations Rule 203(g)(1)(B), 203(g)(2), 
203(g)(3), and

[[Page 336]]

203(g)(4) shall notify the Administrator, no later than October 1, 1973, 
of his intent to utilize either low ash fuel or a stack gas cleaning 
system to meet the requirements of said regulation.
    (b) Any owner or operator of a stationary source subject to 
paragraph (b)(2)(iv)(a) of this section who elects to utilize low ash 
fuel shall take the following actions with respect to the source no 
later than the date specified.
    (1) November 1, 1973--Submit to the Administrator a projection of 
the amount of fuel, by types, that will be substantially adequate to 
enable compliance with Illinois Air Pollution Control Regulations Rule 
203(g)(1)(B), 203(g)(2), 203(g)(3), and 203(g)(4) on May 31, 1975, and 
for at least one year thereafter.
    (2) December 31, 1973--Sign contracts with fuel suppliers for fuel 
requirements as projected above.
    (3) January 31, 1974--Submit a statement as to whether boiler 
modifications will be required. If modifications will be required, 
submit plans for such modifications.
    (4) March 15, 1974--Let contracts for necessary boiler 
modifications, if applicable.
    (5) June 15, 1974--Initiate onsite modifications, if applicable.
    (6) March 31, 1975--Complete onsite modifications, if applicable.
    (7) May 31, 1975--Final compliance with the emission limitation of 
Rule 203(g)(1)(B), 203(g)(2), 203(g)(3), and 203(g)(4).
    (c) Any owner or operator of a stationary source subject to 
paragraph (b)(2)(iv)(a) of this section who elects to utilize a stack 
gas cleaning system shall take the following actions with respect to the 
source no later than the date specified.
    (1) January 15, 1974--Let necessary contracts for construction.
    (2) April 1, 1974--Initiate onsite construction.
    (3) April 1, 1975--Complete onsite construction.
    (4) May 31, 1975--Complete shakedown operations and performance 
tests on source, submit performance test results to the Administrator; 
achieve full compliance with Rule 203(g)(1)(B), 203(g)(2), 203(g)(3), 
and 203(g)(4).
    (v) Ten days prior to the conduct of any performance test required 
by this paragraph, the owner or operator of the affected source shall 
give notice of such test to the Administrator to afford him the 
opportunity to have an observer present.
    (vi) Any owner or operator subject to a compliance schedule above 
shall certify to the Administrator, within five days after the deadline 
for each increment of progress in that schedule, whether or not the 
increment has been met.
    (3)(i) None of the above paragraphs shall apply to a source which is 
presently in compliance with applicable regulations and which has 
certified such compliance to the Administrator by October 1, 1973. The 
Administrator may request whatever supporting information he considers 
necessary for proper certification.
    (ii) Any compliance schedule adopted by the State and approved by 
the Administrator shall satisfy the requirements of this paragraph for 
the affected source.
    (iii) Any owner or operator subject to a compliance schedule in this 
paragraph may submit to the Administrator no later than October 1, 1973, 
a proposed alternative compliance schedule. No such compliance schedule 
may provide for final compliance after the final compliance date in the 
applicable compliance schedule of this paragraph. If promulgated by the 
Administrator, such schedule shall satisfy the requirements of this 
paragraph for the affected source.
    (4) Nothing in this paragraph shall preclude the Administrator from 
promulgating a separate schedule for any source to which the application 
of the compliance schedules in paragraph (b)(2) of this section fail to 
satisfy the requirements of Secs. 51.261 and 51.262(a) of this chapter.
    (c) [Reserved]
    (d) The compliance schedules for the sources identified below are 
disapproved as not meeting the requirements of subpart N of this 
chapter. All regulations cited are air pollution control regulations of 
the State, unless otherwise noted.

[[Page 337]]



----------------------------------------------------------------------------------------------------------------
                Source                         Location           Regulation involved     Date schedule adopted
----------------------------------------------------------------------------------------------------------------
                                                christian county
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
Allied Mills, Inc....................  Taylorville............  204(c).................  Feb. 28, 1973.
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
                                                   cook county
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
Harco Aluminum Inc...................  Chicago................  204(c).................  Dec. 9, 1973.
J. L. Clark Manufacturing Co.........  Downers Grove..........  205(f).................  May 4, 1973.
Johnson & Johnson....................  Bedford Park...........  205(f).................  Jun. 20, 1973.
Lloyd J. Harris Pie, Co. Inc.........  Chicago................  204(c).................  Feb. 27, 1973.
Union Oil Co. of California..........  ......do...............  204(c).................  Jun. 19, 1973,
  (a) No. 10 boiler..................                                                    Dec. 13, 1973.
  (b) 11BIA crude heater.............
W. H. Hutchingson & Son, Inc.........  ......do...............  205(f).................  Aug. 12, 1973.
Western Rust Proof Co................  ......do...............  204(c).................  Oct. 10, 1973.
Wheeler Uniform Service Inc..........  ......do...............  204(c).................  May 22, 1973.
Wm. Yuenger Manufacturing Co.........  ......do...............  204(c).................  Aug. 16, 1973.
World's Finest Chocolate Inc.........  ......do...............  204(c).................  May 30, 1973.
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
                                                 jackson county
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
Tuck Industries, Inc.................  Carbondale.............  204(c).................  Jun. 20, 1973.
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
                                                   kane county
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
All Steel Equipment Corp.............  Montgomery.............  204(f).................  July 24, 1973.
Consolidated Food Inc................  Aurora.................  205(f).................  May 9, 1973.
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
                                                   lake county
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
Morton Manufacturing Co..............  Libertyville...........  205(f).................  Aug. 27, 1973.
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
                                                 la salle county
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
Allied Mills Inc.....................  Mendota................  204(c).................  May 28, 1973.
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
                                                 madison county
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
Clark Oil . Refining Corp............  Hartford...............  204(f).................  Feb. 22, 1973.
Granite City Steel Co................  Granite City...........  203(d)(6)..............  Apr. 25, 1972.
  (a) Coke oven pushing operations...  .......................  .......................  as amended.
  (b) Charging operations............  .......................  .......................  May 21, 1973.
Illinois Power Company (Wood River     E. Alton...............  204(c).................  May 1, 1973.
 Boiler No. 5).
Owens-Illinois Inc...................  Madison................  204(c).................  May 2, 1973.
Owen-Illinois Inc. (No. 2 Powerhouse)  Alton..................  204(c).................  Mar. 30, 1973.
Shell Oil Co. (Cat. Cracker Units      Roxana.................  203(b).................  Nov. 27, 1972.
 Nos. 1, 2).
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
                                                 randolf county
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
Chester Dairy Co.....................  Chester................  204(c).................  Aug. 6, 1973.
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
                                                st. clair county
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
Lock Stove Co........................  East St. Louis.........  205(b).................  June 11, 1973.
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
                                                 tazewell county
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
Quaker Oats Co.......................  Pekin..................  204(c).................  May 24, 1973.
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
                                                vermillion county
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
Lauhoff Grain Co.....................  Danville...............  204(c).................  Mar. 31, 1973.
----------------------------------------------------------------------------------------------------------------

[38 FR 16145, June 20, 1973, as amended at 38 FR 22742, Aug. 23, 1973; 
38 FR 24342, Sept. 7, 1973; 39 FR 28155, Aug. 5, 1974; 51 FR 40675, 
40676, 40677, Nov. 7, 1986; 54 FR 25258, June 14, 1989]

[[Page 338]]



Secs. 52.731--52.735  [Reserved]



Sec. 52.736  Review of new sources and modifications.

    (a) [Reserved]
    (b) The rules submitted by the State on March 24, 1988, to satisfy 
the requirements of the Clean Air Act are approved. These rules are part 
203: Major Stationary Sources Construction and Modification as effective 
March 22, 1991. The moratorium on construction and modification of new 
sources in nonattainment areas as provided in section 110(a)(2)(I) of 
the Clean Air Act is revoked.
[57 FR 59935, Dec. 17, 1992]



Sec. 52.737  Operating permits.

    Emission limitation and other provisions contained in operating 
permits issued by the State in accordance with the provisions of the 
federally approved permit program shall be the applicable requirements 
of the federally approved Illinois SIP for the purpose of section 113 of 
the Clean Air Act and shall be enforceable by USEPA and by any person in 
the same manner as other requirements of the SIP. USEPA reserves the 
right to deem an operating permit not federally enforceable. Such a 
determination will be made according to appropriate procedures, and be 
based upon the permit, permit approval procedures or permit requirements 
which do not conform with the operating permit program requirements or 
the requirements of USEPA's underlying regulations.
[57 FR 59936, Dec. 17, 1992]



Sec. 52.738  Significant deterioration of air quality.

    (a) The requirements of sections 160 through 165 of the Clean Air 
Act are not met, since the plan does not include approvable procedures 
for preventing the significant deterioration of air quality.
    (b) Regulations for preventing significant deterioration of air 
quality. The provisions of Sec. 52.21(b) through (w) are hereby 
incorporated and made a part of the applicable state plan for the State 
of Illinois.
    (c) All applications and other information required pursuant to 
Sec. 52.21 from sources located in the State of Illinois shall be 
submitted to the Director of the Illinois Environmental Protection 
Agency, 2200 Churchill Road, Springfield, Illinois 62706 instead of the 
EPA Region V office.
[45 FR 52741, Aug. 7, 1980, as amended at 46 FR 9584, Jan. 29, 1981]



Sec. 52.739  Permit fees.

    (a) The requirements of section 110(a)(2)(K) of the Clean Air Act as 
amended in 1977 are not met since the state has not submitted to EPA, as 
a part of its State Implementation Plan, provisions for a permit fee 
system.
[46 FR 23237, Apr. 24, 1981]



Sec. 52.740  Interstate pollution.

    (a) The requirements of section 126(a)(2) of the Clean Air Act as 
amended in 1977 are not met since the state has not submitted to EPA, as 
a part of its State Implementation Plan, the procedures on which the 
state is relying to notify nearby states of any proposed major 
stationary source which may significantly contribute to levels of air 
pollution in excess of the National Ambient Air Quality Standards in 
that state.
[46 FR 23237, Apr. 24, 1981]



Sec. 52.741  Control strategy: Ozone control measures for Cook, DuPage, Kane, Lake, McHenry and Will Counties.

    (a) General Provisions--(1) Abbreviations and conversion factors. 
(i) The following abbreviations are used in Sec. 52.741:

ASTM                                American Society for Testing and
                                     Materials.
bbl                                 barrels (42 gallons).
 deg.C                              degrees Celsius or centigrade.
cm                                  centimeters.
cu in.                              cubic inches.
 deg.F                              degrees Fahrenheit.
FIP                                 Federal implementation plan.
ft                                  feet.
ft\2\                               square feet.
g                                   grams.
gpm                                 gallons per minute.
g/mole                              grams per mole.
gal                                 gallons.
hr                                  hours.
in                                  inches.
K                                   degrees Kelvin.
kcal                                kilocalories.
kg                                  kilograms.

[[Page 339]]

kg/hr                               kilograms per hour.
kPa                                 kilopascals; one thousand newtons
                                     per square meter.
l                                   liters.
l/sec                               liters per second.
lbs                                 pounds.
lbs/hr                              pounds per hour.
lbs/gal                             pounds per gallon.
LEL                                 lower explosive limit.
m                                   meters.
m\2\                                square meters.
m\3\                                cubmic meters.
mg                                  milligrams.
Mg                                  Megagrams, metric tons or tonnes.
ml                                  milliliters.
min                                 minutes.
MJ                                  megajoules.
mm Hg                               millimeters of mercury.
ppm                                 parts per million.
ppmv                                parts per million by volume.
psi                                 pounds per square inch.
psia                                pounds per square inch absolute.
psig                                pounds per square inch gauge.
scf                                 standard cubic feet.
scm                                 standard cubic meters.
sec                                 seconds.
SIP                                 State implementation plan.
sq cm                               square centimeters.
sq in                               square inches.
USEPA                               United States Environmental
                                     Protection Agency.
VOC                                 volatile organic compounds.
VOL                                 volatile organic liquids.
VOM                                 volatile organic materials.

    (ii) The following conversion factors are used in Sec. 52.741.

1 gal                                3.785 l.
1,000 gal                            3,785 l or 3.785 m\3\.
1 psia                               6.897 kPa (51.71 mm Hg).
2.205 lbs                            1 kg.
1 bbl                                159.0 l.
1 cu in                              16.39 ml.
1 lb/gal                             119,800 mg/l.
1 ton                                0.907 Mg.

    (2) Applicability. (i) Any source that received a stay, as indicated 
in Sec. 218.103(a)(2), remains subject to the stay if still in effect, 
or (if the stay is no longer in effect) the federally-promulgated or 
federally-approved rule applicable to such source.
    (ii)(A) Effective November 20, 1996 Illinois Administrative Code 
Title 35: Environmental Protection, Subtitle B: Air pollution, Chapter 
I: Pollution Control Board, Subchapter c: Emissions Standards and 
Limitations for Stationary Sources, Part 211: Definitions and General 
Provisions, and Part 218: Organic Material Emission Standards and 
Limitations for the Chicago Area replace the requirements of 40 CFR 
52.741 Control strategy: Ozone control measures for Cook, DuPage, Kane, 
Lake, McHenry and Will County as the federally enforceable control 
measures in these counties for the major non-Control Technique Guideline 
(CTG) sources in the Chicago area, previously subject to paragraph u, v, 
w, or x because of the applicability criteria in these paragraphs.
    (B) In accordance with Sec. 218.101(b), for the major non-CTG 
sources subject to paragraphs u, v, w, or x because of the applicability 
criteria of those paragraphs, the requirements of paragraphs u, v, w, 
and x, and the recordkeeping requirements in paragraph y and any related 
parts of Sec. 52.741 necessary to implement these paragraphs (including, 
but not limited to, those paragraphs containing test methods and 
definitions), shall remain in effect and are enforceable after November 
20, 1996 for the period from July 30, 1990 until November 20, 1996.
    (iii)(A) Except as provided in paragraphs (a)(2) (i) and (ii) of 
this section, effective October 11, 1994, Illinois Administrative Code 
Title 35: Environmental Protection, Subtitle B: Air pollution, Chapter 
I: Pollution Control Board, Subchapter c: Emissions Standards and 
Limitations for Stationary Sources, Part 211: Definitions and General 
Provisions, and Part 218: Organic Material Emission Standards and 
Limitations for the Chicago Area replace the requirements of this 
Sec. 52.741 Control strategy: Ozone control measures for Cook, DuPage, 
Kane, Lake, McHenry and Will County as the federally enforceable control 
measures in these counties.
    (B) In accordance with Sec. 218.101(b), the requirements of 
Sec. 52.741 shall remain in effect and are enforceable after October 11, 
1994, for the period from July 30, 1990, to October 11, 1994.
    (3) Definitions. The following terms are defined for the purpose of 
Sec. 52.741.


    Note: The Federal definitions supersede the State definitions for 
these terms, which were previously approved by USEPA as part of the SIP. 
The federally approved definitions for all other terms remain in effect 
and applicable to these Federal rules.



[[Page 340]]


    Accelacota means a pharmaceutical coating operation which consists 
of a horizontally rotating perforated drum in which tablets are placed, 
a coating is applied by spraying, and the coating is dried by the flow 
of air across the drum through the perforations.
    Accumulator means the reservoir of a condensing unit receiving the 
condensate from a surface condenser.
    Actual emissions means the actual quantity of VOM emissions from an 
emission source during a particular time period.
    Adhesive means any substance or mixture of substances intended to 
serve as a joining compound.
    Administrator means the Administrator of the USEPA or that person's 
designee.
    Afterburner means a control device in which materials in gaseous 
effluent are combusted.
    Air contaminant means any solid, liquid, or gaseous matter, any 
odor, or any form of energy, that is capable of being released into the 
atmosphere from an emission source.
    Air dried coatings means any coatings that dry by use of air or 
forced air at temperatures up to 363.15 K (194  deg.F).
    Air pollution means the presence in the atmosphere of one or more 
air contaminants in sufficient quantities and of such characteristics 
and duration as to be injurious to human, plant, or animal life, to 
health, or to property, or to unreasonably interfere with the enjoyment 
of life or property.
    Air pollution control equipment means any equipment or facility of a 
type intended to eliminate, prevent, reduce or control the emission of 
specified air contaminants to the atmosphere.
    Air suspension coater/dryer means a pharmaceutical coating operation 
which consists of vertical chambers in which tablets or particles are 
placed, and a coating is applied and then dried while the tablets or 
particles are kept in a fluidized state by the passage of air upward 
through the chambers.
    Air-assisted airless spray means a spray coating method which 
combines compressed air with hydraulic pressure to atomize the coating 
material into finer droplets than is achieved with pure airless spray. 
Lower hydraulic pressure is used than with airless spray.
    Airless spray means a spray coating method in which the coating is 
atomized by forcing it through a small opening at high pressure. The 
coating liquid is not mixed with air before exiting from the nozzle.
    Allowable emissions means the quantity of VOM emissions during a 
particular time period from a stationary source calculated using the 
maximum rated capacity of the source (unless restricted by federally 
enforceable limitations on operating rate, hours of operation, or both) 
and the most stringent of:
    (A) The applicable standards in 40 CFR parts 60 and 61:
    (B) The applicable implementation plan; or
    (C) A federally enforceable permit.
    Ambient air quality standards means those standards designed to 
protect the public health and welfare codified in 40 CFR part 50 and 
promulgated from time to time by the USEPA pursuant to authority 
contained in Section 108 of the Clean Air Act, 42 U.S.C. 7401 et seq., 
as amended from time to time.
    Applicator means a device used in a coating line to apply coating.
    As applied means the exact formulation of a coating during 
application on or impregnation into a substrate.
    Asphalt means the dark-brown to black cementitious material (solid, 
semisolid, or liquid in consistency) of which the main constituents are 
bitumens which occur naturally or as a residue of petroleum refining.
    Automobile means a motor vehicle capable of carrying no more than 12 
passengers.
    Automobile or light-duty truck assembly plant means a facility where 
parts are assembled or finished for eventual inclusion into a finished 
automobile or light-duty truck ready for sale to vehicle dealers, but 
not including customizers, body shops, and other repainters.
    Automobile or light-duty truck refinishing means the repainting of 
used automobiles and light-duty trucks.
    Baked coatings means any coating which is cured or dried in an oven 
where the oven air temperature exceeds 90 deg.C (194 deg.F).

[[Page 341]]

    Binders means organic materials and resins which do not contain 
VOM's.
    Bituminous coatings means black or brownish coating materials which 
are soluble in carbon disulfide, which consist mainly of hydrocarbons, 
and which are obtained from natural deposits or as residues from the 
distillation of crude oils or of low grades of coal.
    Brush or wipe coating means a manual method of applying a coating 
using a brush, cloth, or similar object.
    Bulk gasoline plant means a gasoline storage and distribution 
facility with an average throughput of 76,000 l (20,000 gal) or less on 
a 30-day rolling average that distributes gasoline to gasoline 
dispensing facilities.
    Can means any metal container, with or without a top, cover, spout 
or handles, into which solid or liquid materials are packaged.
    Can coating means any coating applied on a single walled container 
that is manufactured from metal sheets thinner than 29 gauge (0.0141 
in.).
    Can coating facility means a facility that includes one or more can 
coating line(s).
    Can coating line means a coating line in which any protective, 
decorative, or functional coating is applied onto the surface of cans or 
can components.
    Capture means the containment or recovery of emissions from a 
process for direction into a duct which may be exhausted through a stack 
or sent to a control device. The overall abatement of emissions from a 
process with an add-on control device is a function both of the capture 
efficiency and of the control device.
    Capture device means a hood, enclosed room floor sweep or other 
means of collecting solvent or other pollutants into a duct. The 
pollutant can then be directed to a pollution control device such as an 
afterburner or carbon adsorber. Sometimes the term is used loosely to 
include the control device.
    Capture efficiency means the fraction of all VOM generated by a 
process that are directed to an abatement or recovery device.
    Capture system means all equipment (including, but not limited to, 
hoods, ducts, fans, ovens, dryers, etc.) used to contain, collect and 
transport an air pollutant to a control device.
    Clean Air Act means the Clean Air Act of 1963, as amended, including 
the Clean Air Act Amendments of 1977, (42 U.S.C. 7401 et seq.).
    Clear coating means coatings that lack color and opacity or are 
transparent using the undercoat as a reflectant base or undertone color.
    Clear topcoat means the final coating which contains binders, but 
not opaque pigments, and is specifically formulated to form a 
transparent or translucent solid protective film.
    Closed vent system means a system that is not open to the atmosphere 
and is composed of piping, connections, and, if necessary, flow inducing 
devices that transport gas or vapor from an emission source to a control 
device.
    Coating means a material applied onto or impregnated into a 
substrate for protective, decorative, or functional purposes. Such 
materials include, but are not limited to, paints, varnishes, sealers, 
adhesives, thinners, diluents, and inks.
    Coating applicator means equipment used to apply a coating.
    Coating line means an operation consisting of a series of one or 
more coating applicators and any associated flash-off areas, drying 
areas, and ovens wherein a surface coating is applied, dried, or cured. 
(It is not necessary for an operation to have an oven, or flash-off 
area, or drying area to be included in this definition.)
    Coating plant means any plant that contains one or more coating 
line(s).
    Coil means any flat metal sheet or strip that is rolled or wound in 
concentric rings.
    Coil coating means any coating applied on any flat metal sheet or 
strip that comes in rolls or coils.
    Coil coating facility means a facility that includes one or more 
coil coating line(s).
    Coil coating line means a coating line in which any protective, 
decorative or functional coating is applied onto the surface of flat 
metal sheets, strips, rolls, or coils for industrial or commercial use.
    Cold cleaning means the process of cleaning and removing soils from 
surfaces by spraying, brushing, flushing, or immersion while maintaining 
the organic solvent below its boiling point.

[[Page 342]]

Wipe cleaning is not included in this definition.
    Component means, with respect to synthetic organic chemical and 
polymer manufacturing equipment, and petroleum refining and related 
industries, any piece of equipment which has the potential to leak VOM 
including, but not limited to, pump seals, compressor seals, seal oil 
degassing vents, pipeline valves, pressure relief devices, process 
drains, and open ended pipes. This definition excludes valves which are 
not externally regulated, flanges, and equipment in heavy liquid 
service. For purposes of paragraph (i) of this section, this definition 
also excludes bleed ports of gear pumps in polymer service.
    Concrete curing compounds means any coating applied to freshly 
poured concrete to retard the evaporation of water.
    Condensate means volatile organic liquid separated from its 
associated gases, which condenses due to changes in the temperature or 
pressure and remains liquid at standard conditions.
    Continuous process means, with respect to polystyrene resin, a 
method of manufacture in which the styrene raw material is delivered on 
a continuous basis to the reactor in which the styrene is polymerized to 
polystyrene.
    Control device means equipment (such as an afterburner or adsorber) 
used to remove or prevent the emission of air pollutants from a 
contaminated exhaust stream.
    Control device efficiency means the ratio of pollution prevented by 
a control device and the pollution introduced to the control device, 
expressed as a percentage.
    Conveyorized degreasing means the continuous process of cleaning and 
removing soils from surfaces utilizing either cold or vaporized 
solvents.
    Crude oil means a naturally occurring mixture which consists of 
hydrocarbons and sulfur, nitrogen, or oxygen derivatives of hydrocarbons 
and which is a liquid at standard conditions.
    Crude oil gathering means the transportation of crude oil or 
condensate after custody transfer between a production facility and a 
reception point.
    Custody transfer means the transfer of produced petroleum and/or 
condensate after processing and/or treating in the producing operations, 
from storage tanks or automatic transfer facilities to pipelines or any 
other forms of transportation.
    Daily-weighted average VOM content means the average VOM content of 
two or more coatings as applied on a coating line during any day, taking 
into account the fraction of total coating volume that each coating 
represents, as calculated with the following equation:
[GRAPHIC] [TIFF OMITTED] TC07NO91.000

where:
VOMw=The average VOM content of two or more coatings as 
          applied each day on a coating line in units of kg VOM/l (lbs 
          VOM/gal) of coating (minus water and any compounds which are 
          specifically exempted from the definition of VOM),
n=The number of different coatings as applied each day on a coating 
          line,
Vi=The volume of each coating (minus water and any compounds 
          which are specifically exempted from the definition of VOM) as 
          applied each day on a coating line in units of l (gal).
Ci=The VOM content of each coating as applied each day on a 
          coating line in units of kg VOM/l (lbs VOM/gal) of coating 
          (minus water and any compounds which are specifically exempted 
          from the definition of VOM), and
VT=The total volume of all coatings (minus water and any 
          compounds which are specifically exempted from the definition 
          of VOM) as applied each day on a coating line in units of l 
          (gal).

    Day means the consecutive 24 hours beginning at 12 a.m. (midnight) 
local time.
    Degreaser means any equipment or system used in solvent cleaning.
    Delivery vessel means any tank truck or trailer equipped with a 
storage tank that is used for the transport of gasoline to a stationary 
storage tank at a gasoline dispensing facility, bulk gasoline plant, or 
bulk gasoline terminal.
    Dip coating means a method of applying coatings in which the part is 
submerged in a tank filled with the coating.

[[Page 343]]

    Drum means any cylindrical metal shipping container of 13- to 110-
gallon capacity.
    Electrostatic bell or disc spray means an electrostatic spray 
coating method in which a rapidly-spinning bell- or disc-shaped 
applicator is used to create a fine mist and apply the coating with high 
transfer efficiency.
    Electrostatic spray means a spray coating method in which opposite 
electrical charges are applied to the substrate and the coating. The 
coating is attracted to the object due to the electrostatic potential 
between them.
    Emission source and source mean any facility from which VOM is 
emitted or capable of being emitted into the atmosphere.
    Enamel means a coating that cures by chemical cross-linking of its 
base resin. Enamels can be distinguished from lacquers because enamels 
are not readily resoluble in their original solvent.
    Enclose means to cover any VOL surface that is exposed to the 
atmosphere.
    End sealing compound coat means a compound applied to can ends which 
functions as a gasket when the end is assembled onto the can.
    Excessive release means a discharge of more than 295 g (0.65 lbs) of 
mercaptans and/or hydrogen sulfide into the atmosphere in any 5-minute 
period.
    Exterior base coat means a coating applied to the exterior of a can 
body, or flat sheet to provide protection to the metal or to provide 
background for any lithographic or printing operation.
    Exterior end coat means a coating applied to the exterior end of a 
can to provide protection to the metal.
    External-floating roof means a cover over an open top storage tank 
consisting of a double deck or pontoon single deck which rests upon and 
is supported by the volatile organic liquid being contained and is 
equipped with a closure seal or seals to close the space between the 
roof edge and tank shell.
    Extreme environmental conditions means exposure to any or all of the 
following: ambient weather conditions; temperatures consistently above 
95  deg.C (203  deg.F); detergents; abrasive and scouring agents; 
solvents; or corrosive atmospheres.
    Extreme performance coating means any coating which during intended 
use is exposed to extreme environmental conditions.
    Fabric coating means any coating applied on textile fabric. Fabric 
coating includes the application of coatings by impregnation.
    Fabric coating facility means a facility that includes one or more 
fabric coating lines.
    Fabric coating line means a coating line in which any protective, 
decorative, or functional coating or reinforcing material is applied on 
or impregnated into a textile fabric.
    Federally enforceable means all limitations and conditions which are 
enforceable by the Administrator including those requirements developed 
pursuant to 40 CFR parts 60 and 61; requirements within any applicable 
implementation plan; and any permit requirements established pursuant to 
40 CFR 52.21 or under regulations approved pursuant to 40 CFR part 51 
subpart I and 40 CFR 51.166.
    Final repair coat means the repainting of any topcoat which is 
damaged during vehicle assembly.
    Firebox means the chamber or compartment of a boiler or furnace in 
which materials are burned, but not the combustion chamber or 
afterburner of an incinerator.
    Fixed-roof tank means a cylindrical shell with a permanently affixed 
roof.
    Flexographic printing means the application of words, designs, and 
pictures to a substrate by means of a roll printing technique in which 
the pattern to be applied is raised above the printing roll and the 
image carrier is made of elastomeric materials.
    Flexographic printing line means a printing line in which each roll 
printer uses a roll with raised areas for applying an image such as 
words, designs, or pictures to a substrate. The image carrier on the 
roll is made of rubber or other elastome
    Floating roof means a roof on a stationary tank, reservoir, or other 
container which moves vertically upon change in volume of the stored 
material.
    Fountain solution means the solution which is applied to the image 
plate to

[[Page 344]]

maintain hydrophilic properties of the non-image areas.
    Fuel combustion emission source means any furnace, boiler, or 
similar equipment used for the primary purpose of producing heat or 
power by indirect heat transfer.
    Fuel gas system means a system for collection of refinery fuel gas 
including, but not limited to, piping for collecting tail gas from 
various process units, mixing drums and controls, and distribution 
piping.
    Gas/gas method means either of two methods for determining capture 
which rely only on gas phase measurements. The first method requires 
construction of a temporary total enclosure (TTE) to ensure that all 
would-be fugitive emissions are measured. The second method uses the 
building or room which houses the facility as an enclosure. The second 
method requires that all other VOM sources within the room be shut down 
while the test is performed, but all fans and blowers within the room 
must be operated according to normal procedures.
    Gas service means that the component contains process fluid that is 
in the gaseous state at operating conditions.
    Gasoline means any petroleum distillate or petroleum distillate/
alcohol blend having a Reid vapor pressure of 27.6 kPa or greater which 
is used as a fuel for internal combustion engines.
    Gasoline dispensing facility means any site where gasoline is 
transferred from a stationary storage tank to a motor vehicle gasoline 
tank used to provide fuel to the engine of that motor vehicle.
    Gross vehicle weight means the manufacturer's gross weight rating 
for the individual vehicle.
    Gross vehicle weight rating means the value specified by the 
manufacturer as the maximum design loaded weight of a single vehicle.
    Heated airless spray means an airless spray coating method in which 
the coating is heated just prior to application.
    Heatset means a class of web-offset lithography which requires a 
heated dryer to solidify the printing inks.
    Heatset-web-offset lithographic printing line means a lithographic 
printing line in which a blanket cylinder is used to transfer ink from a 
plate cylinder to a substrate continuously fed from a roll or an 
extension process and an oven is used to solidify the printing inks.
    Heavy liquid means liquid with a true vapor pressure of less than 
0.3 kPa (0.04 psi) at 294.3 K (70  deg.F) established in a standard 
reference text or as determined by ASTM method D2879-86 (incorporated by 
reference as specified in 40 CFR 52.742); or which has 0.1 Reid Vapor 
Pressure as determined by ASTM method D323-82 (incorporated by reference 
as specified in 40 CFR 52.742); or which when distilled requires a 
temperature of 421.95 K (300  deg.F) or greater to recover 10 percent of 
the liquid as determined by ASTM method D86-82 (incorporated by 
reference as specified in 40 CFR 52.742).
    Heavy off-highway vehicle products means, for the purpose of 
paragraph (e) of this section, heavy construction, mining, farming, or 
material handling equipment; heavy industrial engines; diesel-electric 
locomotives and associated power generation equipment; and the 
components of such equipment or engines.
    Heavy off-highway vehicle products coating facility means a facility 
that includes one or more heavy off-highway vehicle products coating 
line(s).
    Heavy off-highway vehicle products coating line means a coating line 
in which any protective, decorative, or functional coating is applied 
onto the surface of heavy off-highway vehicle products.
    High temperature aluminum coating means a coating that is certified 
to withstand a temperature of 537.8  deg.C (1000  deg.F) for 24 hours.
    Hood means a partial enclosure or canopy for capturing and 
exhausting, by means of a draft, the organic vapors or other fumes 
rising from a coating process or other source.
    Hood capture efficiency means the emissions from a process which are 
captured by the hood and directed into a control device, expressed as a 
percentage of all emissions.
    Hot well means the reservoir of a condensing unit receiving the 
condensate from a barometric condenser.
    Hour means a block period of 60 minutes (e.g., 1 a.m. to 2 a.m.).

[[Page 345]]

    In vacuum service means, for the purpose of paragraph (i) of this 
section, equipment which is operating at an internal pressure that is at 
least 5 kPa (0.73 psia) below ambient pressure.
    In-process tank means a container used for mixing, blending, 
heating, reacting, holding, crystallizing, evaporating or cleaning 
operations in the manufacture of pharmaceuticals.
    Incinerator means a combustion apparatus in which refuse is burned.
    Indirect heat transfer means transfer of heat in such a way that the 
source of heat does not come into direct contact with process materials.
    Ink means a coating used in printing, impressing, or transferring an 
image onto a substrate.
    Interior body spray coat means a coating applied by spray to the 
interior of a can body.
    Internal-floating roof means a cover or roof in a fixed-roof tank 
which rests upon and is supported by the volatile organic liquid being 
contained and is equipped with a closure seal or seals to close the 
space between the roof edge and tank shell.
    Lacquers means any clear wood finishes formulated with 
nitrocellulose or synthetic resins to dry by evaporation without 
chemical reaction, including clear lacquer sanding sealers.
    Large appliance means any residential and commercial washers, 
dryers, ranges, refrigerators, freezers, water heaters, dish washers, 
trash compactors, air conditioners, and other similar products.
    Large appliance coating means any coating applied to the component 
metal parts (including, but not limited to, doors, cases, lids, panels, 
and interior support parts) of residential and commercial washers, 
dryers, ranges, refrigerators, freezers, water heaters, dish washers, 
trash compactors, air conditioners, and other similar products.
    Large appliance coating facility means a facility that includes one 
or more large appliance coating line(s).
    Large appliance coating line means a coating line in which any 
protective, decorative, or functional coating is applied onto the 
surface of large appliances.
    Light liquid means VOM in the liquid state which is not defined as 
heavy liquid.
    Light-duty truck means any motor vehicle rated at 3,850 kg gross 
vehicle weight or less, designed mainly to transport property.
    Liquid/gas method means either of two methods for determining 
capture which require both gas phase and liquid phase measurements and 
analysis. The first method requires construction of a TTE. The second 
method uses the building or room which houses the facility as an 
enclosure. The second method requires that all other VOM sources within 
the room be shut down while the test is performed, but all fans and 
blowers within the room must be operated according to normal procedures.
    Liquid service means that the equipment or component contains 
process fluid that is in a liquid state at operating conditions.
    Lithographic printing line means a printing line, except that the 
substrate is not necessarily fed from an unwinding roll, in which each 
roll printer uses a roll where both the image and non-image areas are 
essentially in the same plane (planographic).
    Magnet wire means aluminum or copper wire formed into an 
electromagnetic coil.
    Magnet wire coating means any coating or electrically insulating 
varnish or enamel applied to magnet wire.
    Magnet wire coating facility means a facility that includes one or 
more magnet wire coating line(s).
    Magnet wire coating line means a coating line in which any 
protective, decorative, or functional coating is applied onto the 
surface of a magnet wire.
    Malfunction means any sudden and unavoidable failure of air 
pollution control equipment, process equipment, or a process to operate 
in a normal or usual manner. Failures that are caused entirely or in 
part by poor maintenance, careless operation, or any other preventable 
upset condition or preventable equipment breakdown shall not be 
considered malfunctions.
    Manufacturing process means a method whereby a process emission 
source or series of process emission sources is used to convert raw 
materials, feed

[[Page 346]]

stocks, subassemblies, or other components into a product, either for 
sale or for use as a component in a subsequent manufacturing process.
    Maximum theoretical emissions means the quantity of volatile organic 
material emissions that theoretically could be emitted by a stationary 
source before add-on controls based on the design capacity or maximum 
production capacity of the source and 8760 hours per year. The design 
capacity or maximum production capacity includes use of coating(s) or 
ink(s) with the highest volatile organic material content actually used 
in practice by the source.
    Metal furniture means a furniture piece including, but not limited 
to, tables, chairs, waste baskets, beds, desks, lockers, benches, 
shelving, file cabinets, lamps, and room dividers.
    Metal furniture coating means any non-adhesive coating applied to 
any furniture piece made of metal or any metal part which is or will be 
assembled with other metal, wood, fabric, plastic or glass parts to form 
a furniture piece including, but not limited to, tables, chairs, waste 
baskets, beds, desks, lockers, benches, shelving, file cabinets, lamps, 
and room dividers. This definition shall not apply to any coating line 
coating miscellaneous metal parts or products.
    Metal furniture coating facility means a facility that includes one 
or more metal furniture coating line(s).
    Metal furniture coating line means a coating line in which any 
protective, decorative, or functional coating is applied onto the 
surface of metal furniture.
    Metallic shoe-type seal means a primary or secondary seal 
constructed of metal sheets (shoes) which are joined together to form a 
ring, springs, or levers which attach the shoes to the floating roof and 
hold the shoes against the tank wall, and a coated fabric which is 
suspended from the shoes to the floating roof.
    Miscellaneous fabricated product manufacturing process means:
    (A) A manufacturing process involving one or more of the following 
applications, including any drying and curing of formulations, and 
capable of emitting VOM:

    (1) Adhesives to fabricate or assemble components or products.
    (2) Asphalt solutions to paper or fiberboard.
    (3) Asphalt to paper or felt.
    (4) Coatings or dye to leather.
    (5) Coatings to plastic.
    (6) Coatings to rubber or glass.
    (7) Disinfectant material to manufactured items.
    (8) Plastic foam scrap or ``fluff'' from the manufacture of foam 
containers and packaging material to form resin pallets.
    (9) Resin solutions to fiber substances.
    (10) Viscose solutions for food casings.


    (B) The storage and handling of formulations associated with the 
process described above, and the use and handling of organic liquids and 
other substances for clean-up operations associated with the process 
described in this definition.

    Miscellaneous formulation manufacturing process means:
    (A) A manufacturing process which compounds one or more of the 
following and is capable of emitting VOM:

    (1) Adhesives.
    (2) Asphalt solutions.
    (3) Caulks, sealants, or waterproofing agents.
    (4) Coatings, other than paint and ink.
    (5) Concrete curing compounds.
    (6) Dyes.
    (7) Friction materials and compounds.
    (8) Resin solutions.
    (9) Rubber solutions.
    (10) Viscose solutions.


    (B) The storage and handling of formulations associated with the 
process described above, and the use and handling of organic liquids and 
other substances for clean-up operations associated with the process 
described in this definition.

    Miscellaneous metal parts or products means any metal part or metal 
product, even if attached to or combined with a nonmental part or 
product, except cans, coils, metal furniture, large appliances, magnet 
wire, automobiles, ships, and airplane bodies.
    Miscellaneous metal parts and products coating means any coating 
applied to any metal part or metal product, even if attached to or 
combined with a nonmetal part or product, except cans, coils, metal 
furniture, large appliances, and magnet wire. Prime coat, prime surfacer 
coat, topcoat, and final repair

[[Page 347]]

coat for automobiles and light-duty trucks are not miscellaneous metal 
parts and products coatings. However, underbody anti-chip (e.g., 
underbody plastisol) automobile, and light-duty truck coatings are 
miscellaneous metal parts and products coatings. Also, automobile or 
light-duty truck refinishing coatings, coatings applied to the exterior 
of marine vessels, coatings applied to the exterior of airplanes, and 
the customized topcoating of automobiles and trucks if production is 
less than 35 vehicles per day are not miscellaneous metal parts and 
products coatings.
    Miscellaneous metal parts or products coating facility means a 
facility that includes one or more miscellaneous metal parts or products 
coating lines.
    Miscellaneous metal parts or products coating line means a coating 
line in which any protective, decorative, or functional coating is 
applied onto the surface of miscellaneous metal parts or products.
    Miscellaneous organic chemical manufacturing process means:
    (A) A manufacturing process which produces by chemical reaction, one 
or more of the following organic compounds or mixtures of organic 
compounds and which is capable of emitting VOM:

    (1) Chemicals listed in appendix A of this section.
    (2) Chlorinated and sulfonated compounds.
    (3) Cosmetic, detergent, soap, or surfactant intermediaries or 
specialties and products.
    (4) Disinfectants.
    (5) Food additives.
    (6) Oil and petroleum product additives.
    (7) Plasticizers.
    (8) Resins or polymers.
    (9) Rubber additives.
    (10) Sweeteners.
    (11) Varnishes


    (B) The storage and handling of formulations associated with the 
process described above and the use and handling of organic liquids and 
other substances for clean-up operations associated with the process 
described in this definition.

    Monitor means to measure and record.
    Multiple package coating means a coating made from more than one 
different ingredient which must be mixed prior to using and has a 
limited pot life due to the chemical reaction which occurs upon mixing.
    Offset means, with respect to printing and publishing operations, 
use of a blanket cylinder to transfer ink from the plate cylinder to the 
surface to be printed.
    Opaque stains means all stains that are not semi-transparent stains.
    Open top vapor depressing means the batch process of cleaning and 
removing soils from surfaces by condensing hot solvent vapor on the 
colder metal parts.
    Open-ended valve means any valve, except pressure relief devices, 
having one side of the valve in contact with process fluid and one side 
open to the atmosphere, either directly or through open piping.
    Organic compound means any compound of carbon, excluding carbon 
monoxide, carbon dioxide, carbonic acid, metallic carbides or 
carbonates, and ammonium carbonate.
    Organic material means any chemical compound of carbon including 
diluents and thinners which are liquids at standard conditions and which 
are used as dissolvers, viscosity reducers, or cleaning agents, but 
excluding methane, carbon monoxide, carbon dioxide, carbonic acid, 
metallic carbonic acid, metallic carbide, metallic carbonates, and 
ammonium carbonate.
    Organic vapor means the gaseous phase of an organic material or a 
mixture of organic materials present in the atmosphere.
    Oven means a chamber within which heat is used for one or more of 
the following purposes: Dry, bake, cure, or polymerize a coating or ink.
    Overall control means the product of the capture efficiency and the 
control device efficiency.
    Overvarnish means a transparent coating applied directly over ink or 
coating.
    Owner or operator means any person who owns, operates, leases, 
controls, or supervises an emission source or air pollution control 
equipment.
    Packaging rotogravure printing means rotogravure printing upon 
paper, paper board, metal foil, plastic film, and

[[Page 348]]

other substrates, which are, in subsequent operations, formed into 
packaging products or labels for articles to be sold.
    Packaging rotogravure printing line means a rotogravure printing 
line in which surface coatings are applied to paper, paperboard, foil, 
film, or other substrates which are to be used to produce containers, 
packaging products, or labels for articles.
    Pail means any cylindrical metal shipping container of 1- to 12-
gallon capacity and constructed of 29-gauge and heavier metal.
    Paint manufacturing plant means a plant that mixes, blends, or 
compounds enamels, lacquers, sealers, shellacs, stains, varnishes, or 
pigmented surface coatings.
    Paper coating means any coating applied on paper, plastic film, or 
metallic foil to make certain products, including (but not limited to) 
adhesive tapes and labels, book covers, post cards, office copier paper, 
drafting paper, or pressure sensitive tapes. Paper coating includes the 
application of coatings by impregnation and/or saturation.
    Paper coating facility means a facility that includes one or more 
paper coating lines.
    Paper coating line means a coating line in which any protective, 
decorative, or functional coating is applied on, saturated into, or 
impregnated into paper, plastic film, or metallic foil to make certain 
products, including (but not limited to) adhesive tapes and labels, book 
covers, post cards, office copier paper, drafting paper, and pressure 
sensitive tapes.
    Parts per million (volume) means a volume/volume ratio which 
expresses the volumetric concentration of gaseous air contaminant in a 
million unit volume of gas.
    Person means any individual, corporation, partnership, association, 
State, municipality, political subdivision of a State; any agency, 
department, or instrumentality of the United States; and any officer, 
agent, or employee thereof.
    Petroleum means the crude oil removed from the earth and the oils 
derived from tar sands, shale, and coal.
    Petroleum refinery means any facility engaged in producing gasoline, 
kerosene, distillate fuel oils, residual fuel oils, lubricants, or other 
products through distillation of petroleum, or through redistillation, 
cracking, or reforming of unfinished petroleum derivatives.
    Pharmaceutical means any compound or mixture, other than food, used 
in the prevention, diagnosis, alleviation, treatment, or cure of disease 
in man and animal.
    Pharmaceutical coating operation means a device in which a coating 
is applied to a pharmaceutical, including air drying or curing of the 
coating.
    Pigmented coatings means opaque coatings containing binders and 
colored pigments which are formulated to conceal the wood surface either 
as an undercoat or topcoat.
    Plant means all of the pollutant-emitting activities which belong to 
the same industrial grouping, are located on one or more contiguous or 
adjacent properties, and are under the control of the same person (or 
persons under common control), except the activities of any marine 
vessel. Pollutant-emitting activities shall be considered as part of the 
same industrial grouping if they belong to the same ``Major Group'' 
(i.e., which have the same two-digit code) as described in the 
``Standard Industrial Classification Manual, 1987'' (incorporated by 
reference as specified in 40 CFR 52.742).
    Plasticizers means a substance added to a polymer composition to 
soften and add flexibility to the product.
    Prime coat means the first of two or more coatings applied to a 
surface.
    Prime surfacer coat means a coating used to touch up areas on the 
surface of automobile or light-duty truck bodies not adequately covered 
by the prime coat before application of the top coat. The prime surfacer 
coat is applied between the prime coat and topcoat. An anti-chip coating 
applied to main body parts (e.g., rocker panels, bottom of doors and 
fenders, and leading edge of roof) is a prime surfacer coat.
    Primers means any coatings formulated and applied to substrates to 
provide a firm bond between the substrate and subsequent coats.

[[Page 349]]

    Printing means the application of words, designs, and pictures to a 
substrate using ink.
    Printing line means an operation consisting of a series of one or 
more roll printers and any associated roll coaters, drying areas, and 
ovens wherein one or more coatings are applied, dried, and/or cured.
    Process means any stationary emission source other than a fuel 
combustion emission source or an incinerator.
    Production equipment exhaust system means a system for collecting 
and directing into the atmosphere emissions of volatile organic material 
from reactors, centrifuges, and other process emission sources.
    Publication rotogravure printing line means a rotogravure printing 
line in which coatings are applied to paper which is subsequently formed 
into books, magazines, catalogues, brochures, directories, newspaper 
supplements, or other types of printed material.
    Reactor means a vat, vessel, or other device in which chemical 
reactions take place.
    Refiner means any person who owns, leases operates, controls, or 
supervises a refinery.
    Refinery unit, process unit or unit means a set of components which 
are a part of a basic process operation such as distillation, 
hydrotreating, cracking, or reforming of hydrocarbons.
    Refrigerated condenser means a surface condenser in which the 
coolant supplied to the condenser has been cooled by a mechanical 
device, other than by a cooling tower or evaporative spray cooling, such 
as refrigeration unit or steam chiller unit.
    Repair coatings means coatings used to correct imperfections or 
damage to furniture surface.
    Repaired means, for the purpose of paragraph (i) of this section, 
that equipment component has been adjusted, or otherwise altered, to 
eliminate a leak.
    Roll coater means an apparatus in which a uniform layer of coating 
is applied by means of one or more rolls across the entire width of a 
moving substrate.
    Roll printer means an apparatus used in the application of words, 
designs, or pictures to a substrate, usually by means of one or more 
rolls each with only partial coverage.
    Roll printing means the application of words, designs, and pictures 
to a substrate usually by means of a series of hard rubber or metal 
rolls each with only partial coverage.
    Roller coating means a method of applying a coating to a sheet or 
strip in which the coating is transferred by a roller or series of 
rollers.
    Rotogravure printing means the application of words, designs, and 
pictures to a substrate by means of a roll printing technique in which 
the pattern to be applied is recessed relative to the non-image area.
    Rotogravure printing line means a printing line in which each roll 
printer uses a roll with recessed areas for applying an image to a 
substrate.
    Safety relief valve means a valve which is normally closed and which 
is designed to open in order to relieve excessive pressures within a 
vessel or pipe.
    Sanding sealers means any coatings formulated for and applied to 
bare wood for sanding and to seal the wood for subsequent application of 
varnish. To be considered a sanding sealer a coating must be clearly 
labelled as such.
    Sealer means a coating containing binders which seals wood prior to 
the application of the subsequent coatings.
    Semi-transparent stains means stains containing dyes or semi-
transparent pigments which are formulated to enhance wood grain and 
change the color of the surface but not to conceal the surface, 
including, but not limited to, sap stain, toner, non-grain raising 
stains, pad stain, or spatter stain.
    Set of safety relief valves means one or more safety relief valves 
designed to open in order to relieve excessive pressures in the same 
vessel or pipe.
    Sheet basecoat means a coating applied to metal when the metal is in 
sheet form to serve as either the exterior or interior of a can for 
either two-piece or three-piece cans.
    Side-seam spray coat means a coating applied to the seam of a three-
piece can.
    Single coat means one coating application applied to a metal 
surface.

[[Page 350]]

    Solvent means a liquid substance that is used to dissolve or dilute 
another substance.
    Solvent cleaning means the process of cleaning soils from surfaces 
by cold cleaning, open top vapor degreasing, or conveyorized degreasing.
    Specified air contaminant means any air contaminant as to which this 
Section contains emission standards or other specific limitations.
    Splash loading means a method of loading a tank, railroad tank car, 
tank truck, or trailer by use of other than a submerged loading pipe.
    Standard conditions means a temperature of 70  deg.F and a pressure 
of 14.7 psia.
    Standard cubic foot (scf) means the volume of one cubic foot of gas 
at standard conditions.
    Standard Industrial Classification Manual means the Standard 
Industrial Classification Manual (1987), Superintendent of Documents, 
U.S. Government Printing Office, Washington, DC 20402 (incorporated by 
reference as specified in 40 CFR 52.742).
    Start-up means the setting in operation of an emission source for 
any purpose.
    Stationary emission source and Stationary source mean an emission 
source which is not self-propelled.
    Storage tank or storage vessel means any stationary tank, reservoir 
or container used for the storage of VOL's.
    Submerged loading pipe means any discharge pipe or nozzle which 
meets either of the following conditions:
    (A) Where the tank is filled from the top, the end of the discharge 
pipe or nozzle must be totally submerged when the liquid level is 15 cm 
(6 in.) above the bottom of the tank.
    (B) Where the tank is filled from the side, the discharge pipe or 
nozzle must be totally submerged when the liquid level is 46 cm (18 in.) 
above the bottom of the tank.
    Substrate means the surface onto which a coating is applied or into 
which a coating is impregnated.
    Surface condenser means a device which removes a substance from a 
gas stream by reducing the temperature of the stream, without direct 
contact between the coolant and the stream.
    Tablet coating operation means a pharmaceutical coating operation in 
which tablets are coated.
    Thirty-day rolling average means any value arithmetically averaged 
over any consecutive thirty-days.
    Three-piece can means a can which is made from a rectangular sheet 
and two circular ends.
    Topcoat means a coating applied in a multiple coat operation other 
than prime coat, final repair coat, or prime surfacer coat.
    Topcoat operation means all topcoat spray booths, flash-off areas, 
and bake ovens at a facility which are used to apply, dry, or cure the 
final coatings (except final off-line repair) on components of 
automobile or light-duty truck bodies.
    Transfer efficiency means the ratio of the amount of coating solids 
deposited onto a part or product to the total amount of coating solids 
used.
    True vapor pressure means the equilibrium partial pressure exerted 
by a volatile organic liquid as determined in accordance with methods 
described in American Petroleum Institute Bulletin 2517, ``Evaporation 
Loss From Floating Roof Tanks,'' second edition, February 1980 
(incorporated by reference as specified in 40 CFR 52.742).
    Two-piece can means a can which is drawn from a shallow cup and 
requires only one end to be attached.
    Undercoaters means any coatings formulated for and applied to 
substrates to provide a smooth surface for subsequent coats.
    Unregulated safety relief valve means a safety relief valve which 
cannot be actuated by a means other than high pressure in the pipe or 
vessel which it protects.
    Vacuum producing system means any reciprocating, rotary, or 
centrifugal blower or compressor or any jet ejector or device that 
creates suction from a pressure below atmospheric and discharges against 
a greater pressure.
    Valves not externally regulated means valves that have no external 
controls, such as in-line check valves.
    Vapor balance system means any combination of pipes or hoses which 
creates a closed system between the vapor spaces of an unloading tank 
and a receiving tank such that vapors displaced

[[Page 351]]

from the receiving tank are transferred to the tank being unloaded.
    Vapor collection system means all piping, seals, hoses, connections, 
pressure-vacuum vents, and other possible sources between the gasoline 
delivery vessel and the vapor processing unit and/or the storage tanks 
and vapor holder.
    Vapor control system means any system that limits or prevents 
release to the atmosphere of organic meterial in the vapors displaced 
from a tank during the transfer of gasoline.
    Vapor recovery system means a vapor gathering system capable of 
collecting all VOM vapors and gases discharged from the storage tank and 
a vapor disposal system capable of processing such VOM vapors and gases 
so as to prevent their emission to the atmosphere.
    Vehicle means a device by which any person or property may be 
propelled, moved, or drawn upon a highway, excepting a device moved 
exclusively by human power or used exclusively upon stationary rails or 
tracks.
    Vinyl coating means any topcoat or printing ink applied to vinyl 
coated fabric or vinyl sheets. Vinyl coating does not include 
plastisols.
    Vinyl coating facility means a facility that includes one or more 
vinyl coating line(s).
    Vinyl coating line means a coating line in which any protective, 
decorative or functional coating is applied onto vinyl coated fabric or 
vinyl sheets.
    Volatile organic liquid means any substance which is liquid at 
storage conditions and which contains volatile organic compounds.
    Volatile organic material (VOM) or volatile organic compounds (VOC) 
is as defined in Sec. 51.100(s) of this chapter.
    Wash coat means a coating containing binders which seals wood 
surfaces, prevents undesired staining, and controls penetration.
    Web means a substrate which is printed in continuous roll-fed 
presses.
    Wood furniture means room furnishings including cabinets (kitchen, 
bath, and vanity), tables, chairs, beds, sofas, shutters, art objects, 
wood paneling, wood flooring, and any other coated furnishings made of 
wood, wood composition, or fabricated wood materials.
    Wood furniture coating facility means a facility that includes one 
or more wood furniture coating line(s).
    Wood furniture coating line means a coating line in which any 
protective, decorative, or functional coating is applied onto wood 
furniture.
    Woodworking means the shaping, sawing, grinding, smoothing, 
polishing, and making into products of any form or shape of wood.
    (4) Testing methods and procedures--(i) Coatings, inks and fountain 
solutions. The following test methods and procedures shall be used to 
determine compliance of as applied coatings, inks, and fountain 
solutions with the limitations set forth in Sec. 52.741.
    (A) Sampling. Samples collected for analyses shall be one-liter 
taken into a one-liter container at a location and time such that the 
sample will be representative of the coating as applied (i.e., the 
sample shall include any dilution solvent or other VOM added during the 
manufacturing process). The container must be tightly sealed immediately 
after the sample is taken. Any solvent or other VOM added after the 
sample is taken must be measured and accounted for in the calculations 
in paragraph(a)(4)(i)(C) of this section. For multiple package coatings, 
separate samples of each component shall be obtained. A mixed sample 
shall not be obtained as it will cure in the container. Sampling 
procedures shall follow the guidelines presented in:
    (1) ASTM D3925-81 (Reapproved 1985) Standard Practice for Sampling 
Liquid Paints and Related Pigment Coating. This practice is incorporated 
by reference as specified in 40 CFR 52.742.
    (2) ASTM E300-86 Standard Practice for Sampling Industrial 
Chemicals. This practice is incorporated by reference as specified in 40 
CFR 52.742.
    (B) Analyses. The applicable analytical methods specified below 
shall be used to determine the composition of coatings, inks, or 
fountain solutions as applied.
    (1) Method 24 of 40 CFR part 60, appendix A, shall be used to 
determine the VOM content and density of coatings. If it is demonstrated 
to the satisfaction of the Administrator that plant

[[Page 352]]

coating formulation data are equivalent to Method 24 results, 
formulation data may be used. In the event of any inconsistency between 
a Method 24 test and a facility's formulation data, the Method 24 test 
will govern.
    (2) Method 24A of 40 CFR part 60, appendix A, shall be used to 
determine the VOM content and density of rotogravure printing inks and 
related coatings. If it is demonstrated to the satisfaction of the 
Administrator that the plant coating formulation data are equivalent to 
Method 24A results, formulation data may be used. In the event of any 
inconsistency between a Method 24A test and a facility's formulation 
data, the Method 24A test will govern.
    (3) The following ASTM methods are the analytical procedures for 
determining VOM:

(i) ASTM D1475-85: Standard Test Method for Density of Paint, Varnish, 
Lacquer and Related Products. This test method is incorporated by 
reference as specified in 40 CFR 52.742.
(ii) ASTM D2369-87: Standard Test Method for Volatile Content of 
Coatings. This test method is incorporated by reference as specified in 
40 CFR 52.742.
(iii) ASTM D3792-86: Standard Test Method for Water Content of Water-
reducible Paints by Direct Injection into a Gas Chromatograph. This test 
method is incorporated by reference as specified in 40 CFR 52.742.
(iv) ASTM D4017-81 (Reapproved 1987): Standard Test Method for Water in 
Paints and Paint Materials by the Karl Fischer Method. This test method 
is incorporated by reference as specified in 40 CFR 52.742.
(v) ASTM D4457-85: Standard Test Method for Determination of 
Dichloromethane and 1,1,1-Trichloroethane in Paints and Coatings by 
Direct Injection into a Gas Chromatograph. (The procedure delineated 
above can be used to develop protocols for any compounds specifically 
exempted from the definition of VOM.) This test method is incorporated 
by reference as specified in 40 CFR 52.742.
(vi) ASTM D2697-86: Standard Test Method for Volume Non-Volatile Matter 
in Clear or Pigmented Coatings. This test method is incorporated by 
reference as specified in 40 CFR 52.742.
(vii) ASTM D3980-87: Standard Practice for Interlaboratory Testing of 
Paint and Related Materials. This practice is incorporated by reference 
as specified in 40 CFR 52.742.
(viii) ASTM E180-85: Standard Practice for Determining the Precision of 
ASTM Methods for Analysis of and Testing of Industrial Chemicals. This 
practice is incorporated by reference as specified in 40 CFR 52.742.
(ix) ASTM D2372-85: Standard Method of Separation of Vehicle from 
Solvent-reducible Paints. This method is incorporated by reference as 
specified in 40 CFR 52.742.


    (4) Use of an adaptation to any of the analytical methods specified 
in paragraphs (a)(4)(i)(B)(1), (2) and (3) may be approved by the 
Administrator on a case-by-case basis. An owner or operator must submit 
sufficient documentation for the Administrator to find that the 
analytical methods specified in paragraphs (a)(4)(i)(B)(1), (2) and (3) 
will yield inaccurate results and that the proposed adaptation is 
appropriate.
    (C) Calculations. Calculations for determining the VOM content, 
water content and the content of any compounds which are specifically 
exempted from the definition of VOM of coatings, inks and fountain 
solutions as applied shall follow the guidance provided in the following 
documents.
    (1) ``A Guide for Surface Coating Calculation'' EPA-340/1-86-016 
(which is available from the National Technical Information Services, 
5285 Port Royal Road, Springfield, VA 22161)
    (2) ``Procedures for Certifying Quantity of Volatile Organic 
Compounds Emitted by Paint, Ink and Other Coatings'' (revised June 1986) 
EPA-450/3-84-019 (which is available from the National Technical 
Information Services, 5285 Port Royal Road, Springfield, VA 22161)
    (3) ``A Guide for Graphic Arts Calculations'' August 1988 EPA-340/1-
88-003 (which is available from the National Technical Information 
Services, 5285 Port Royal Road, Springfield, VA 22161)
    (ii) Automobile or light-duty truck test protocol. The protocol for 
testing, including determining the transfer efficiency, of coating 
applicators at topcoat coating operations at an automobile assembly 
facility shall follow the procedure in: ``Protocol for Determining the 
Daily Volatile Organic Compound Emission Rate of Automobile and Light-
Duty Truck Topcoat Operations'' December 1988 EPA-450/3-

[[Page 353]]

88-018 (which is available for purchase from the National Technical 
Information Services, 5285 Port Royal Road, Springfield, VA 22161)
    (iii) Capture system efficiency test protocols--(A) Applicability. 
The requirements of paragraphs (a)(4)(iii)(B) of this section shall 
apply to all VOM emitting processes employing capture equipment (e.g., 
hoods, ducts), except those cases noted below.
    (1) If a source installs a permanent total enclosure (PTE) that 
meets USEPA specifications, and which directs all VOM to a control 
device, then the source is exempted from the requirements described in 
paragraph (B). The USEPA specifications to determine whether a strucutre 
is considered a PTE are given in Procedure T of appendix B of this 
section. In this instance, the capture efficiency is assumed to be 100 
percent and the source is still required to measure control efficiency 
using appropriate test methods as specified in (a)(4)(iv) of this 
section.
    (2) If a source uses a control device designed to collect and 
recover VOM (e.g., carbon adsorber), an explicit measurement of capture 
efficiency is not necessary provided that the conditions given below are 
met. The overall control of the system can be determined by directly 
comparing the input liquid VOM to the recovered liquid VOM. The general 
procedure for use in this situation is given in 40 CFR 60.433, with the 
following additional restrictions:
    (i) The source must be able to equate solvent usage with solvent 
recovery on a 24-hour (daily) basis, rather than a 30-day weighted 
average, within 72 hours following the 24-hour period. In addition, one 
of the following two criteria must be met:
    (ii) The solvent recovery system (i.e., capture and control system) 
must be dedicated to a single process line (e.g., one process line 
venting to a carbon adsorber system), or
    (iii) If the solvent recovery system controls multiple process 
lines, then the source must be able to demonstrate that the overall 
control (i.e., the total recovered solvent VOM divided by the sum of 
liquid VOM input to all process lines venting to the control system) 
meets or exceeds the most stringent standard applicable for any process 
line venting to the control system.
    (B) Specific requirements. The capture efficiency of a process line 
shall be measured using one of the four protocols given below. Any error 
margin associated with a test protocol may not be incorporated into the 
results of a capture efficiency test. If these techniques are not 
suitable for a particular process, then the source must present an 
alternative capture efficiency protocol and obtain approval for it by 
the Administrator as a SIP or FIP revisions.
    (1) Gas/gas method using temporary total enclosure (TTE). The USEPA 
specifications to determine whether a temporary enclosure is considered 
a TTE are given in Procedure T of appendix B of this section. The 
capture efficiency equation to be used for this protocol is:

CE=Gw/(GW+Fw)
where:
CE=capture efficiency, decimal fraction.
Gw=mass of VOM captured and delivered to control device using a TTE.
Fw=mass of fugitive VOM that escapes from a TTE.

Procedure G.2 contained in appendix B of this section is used to obtain 
Gw. Procedure F.1 in appendix B of this section is used to obtain Fw.
    (2) Liquid/gas method using TTE. The USEPA specifications to 
determine whether a temporary enclosure is considered a TTE are given in 
Procedure T of appendix B of this section. The capture efficiency 
equation to be used for this protocol is:

CE=(L-F)/L
where:
CE=capture efficiency, decimal fraction.
L=mass of liquid VOM input to process.
Fw=mass of fugitive VOM that escapes from a TTE.

Procedure L contained in appendix B of this section is used to obtain L. 
Procedure F.1 in appendix B of this section is used to obtain Fw.
    (3) Gas/gas method using the building or room (building or room 
enclosure) in which the affected source is located as the enclosure and 
in which ``F'' and ``G'' are measured while operating only

[[Page 354]]

the affected facility. All fans and blowers in the building or room must 
be operated as they would under normal production. The capture 
efficiency equation to be used for this protocol is:

CE=G/(G+FB)
where:
CE=capture efficiency, decimal fraction.
G=mass of VOM captured and delivered to control device.
FB=mass of fugitive VOM that escapes from building enclosure.

Procedure G.2 contained in appendix B of this section is used to obtain 
G. Procedure F.2 in appendix B of this section is used to obtain 
FB.
    (4) Liquid/gas method using the building or room (building or room 
enclosure) in which the affected source is located as the enclosure and 
in which ``F'' and ``L'' are measured while operating only the affected 
facility. All fans and blowers in the building or room must be operated 
as they would under normal production. The capture efficiency equation 
to be used for this protocol is:

CE=(L-FB)/L

where:
CE=capture efficiency, decimal fraction.
L=mass of liquid VOM input to process.
FB=mass of fugitive VOM that escapes from building enclosure.


Procedure L contained in appendix B of this section is used to obtain L. 
Procedure F.2 in appendix B of this section is used to obtain 
FB.
    (C) Recordkeeping and reporting. (1) All affected facilities must 
maintain a copy of the capture efficiency protocol submitted to USEPA on 
file. All results of the appropriate test methods and capture efficiency 
protocols must be reported to USEPA within sixty (60) days of the test 
date. A copy of the results must be kept on file with the source for a 
period of three (3) years.
    (2) If any changes are made to capture or control equipment, then 
the source is required to notify USEPA of these changes and a new test 
may be required by USEPA.
    (3) The source must notify the Administrator 30 days prior to 
performing any capture efficiency or control test. At that time, the 
source must notify the Administrator which capture efficiency protocol 
and control device test methods will be used.
    (4) Sources utilizing a PTE must demonstrate that this enclosure 
meets the requirement given in Procedure T (in appendix B of this 
section) for a PTE during any testing of their control device.
    (5) Sources utilizing a TTE must demonstrate that their TTE meets 
the requirements given in Procedure T (in appendix B of this section) 
for a TTE during testing of their control device. The source must also 
provide documentation that the quality assurance criteria for a TTE have 
been achieved.
    (iv) Control device efficiency testing and monitoring. (A) The 
control device efficiency shall be determined by simultaneously 
measuring the inlet and outlet gas phase VOM concentrations and gas 
volumetric flow rates in accordance with the gas phase test methods 
specified in paragraph (a)(4)(vi) of this section.
    (B) Any owner or operator that uses an afterburner or carbon 
adsorber to comply with any paragraph of Sec. 52.741 shall use USEPA 
approved continuous monitoring equipment which is installed, calibrated, 
maintained, and operated according to vendor specifications at all times 
the afterburner or carbon adsorber is in use. The continuous monitoring 
equipment must monitor the following parameters:
    (1) Combustion chamber temperature of each afterburner.
    (2) Temperature rise across each catalytic afterburner bed or VOM 
concentration of exhaust.
    (3) The VOM concentration of each carbon adsorption bed exhaust.
    (v) Overall efficiency. (A) The overall efficiency of the emission 
control system shall be determined as the product of the capture system 
efficiency and the control device efficiency or by the liquid/liquid 
test protocol as specified in 40 CFR 60.433 (and revised by paragraph 
(a)(4)(iii)(A)(2) of this section for each solvent recovery system. In 
those cases in which the overall efficiency is being determined for an 
entire line, the capture efficiency used to calculate the product of the 
capture and control efficiency is the total capture efficiency over the 
entire line.

[[Page 355]]

    (B) For coating lines which are both chosen by the owner or operator 
to comply with paragraphs (e)(2)(ii), (e)(2)(iii), (e)(2)(iv), 
(e)(2)(v), or (e)(2)(vi) of this section by the alternative in paragraph 
(e)(2)(i)(B) of this section and meet the criteria allowing them to 
comply with paragraph (e)(2) of this section instead of paragraph (e)(1) 
of this section, the overall efficiency of the capture system and 
control device, as determined by the test methods and procedures 
specified in paragraphs (a)(4) (iii), (iv) and (v)(A) of this section, 
shall be no less than the equivalent overall efficiency which shall be 
calculated by the following equation:

E = ([VOMa - VOM1]/VOMa)  x  100

Where:
E = Equivalent overall efficiency of the capture system and control 
          device as a percentage,
VOMa = Actual VOM content of a coating, or the daily-weighted 
          average VOM content of two or more coatings (if more than one 
          coating is used), as applied to the subject coating line as 
          determined by the applicable test methods and procedures 
          specified in paragraph (a)(4)(i) of this section in units of 
          kg VOM/l (lb VOM/gal) of coating solids as applied,
VOM1 = The VOM emission limit specified in paragraph (e)(2) 
          (i) or (ii) of this section in units of kg VOM/l (lb VOM/gal) 
          of coating solids as applied.


    (vi) Volatile organic material gas phase source test methods. The 
methods in 40 CFR part 60, appendix A, delineated below shall be used to 
determine control device efficiencies.
    (A) 40 CFR part 60, appendix A, Method 18, 25 or 25A, as appropriate 
to the conditions at the site, shall be used to determine VOM 
concentration. Method selection shall be based on consideration of the 
diversity of organic species present and their total concentration and 
on consideration of the potential presence of interfering gases. Except 
as indicated in paragraphs (a)(4)(vi)(A)(1) and (2) of this section, the 
test shall consist of three separate runs, each lasting a minimum of 60 
min, unless the Administrator determines that process variables dictate 
shorter sampling times.
    (1) When the method is to be used to determine the efficiency of a 
carbon adsoption system with a common exhaust stack for all the 
individual adsorber vessels, the test shall consist of three separate 
runs, each coinciding with one or more complete sequences through the 
adsorption cycles of all the individual adsorber vessels.
    (2) When the method is to be used to determine the efficiency of a 
carbon adsorption system with individual exhaust stacks for each 
adsorber vessel, each adsorber vessel shall be tested individually. The 
test for each adsorber vessel shall consist of three separate runs. Each 
run shall coincide with one or more complete adsorption cycles.
    (B) 40 CFR part 60, appendix A, Method 1 or 1A shall be used for 
sample and velocity traverses.
    (C) 40 CFR part 60, appendix A, Method 2, 2A, 2C or 2D shall be used 
for velocity and volumetric flow rates.
    (D) 40 CFR part 60, appendix A, Method 3 shall be used for gas 
analysis.
    (E) 40 CFR part 60, appendix A, Method 4 shall be used for stack gas 
moisture.
    (F) 40 CFR part 60, appendix A, Methods 2, 2A, 2C, 2D, 3 and 4 shall 
be performed, as applicable, at least twice during each test run.
    (G) Use of an adaptation to any of the test methods specified in 
paragraphs (a)(4)(vi) (A), (B), (C), (D), (E), and (F) of this section 
may be approved by the Administrator on a case-by-case basis. An owner 
or operator must submit sufficient documentation for the Administrator 
to find that the test methods specified in paragraphs (a)(4)(vi) (A), 
(B), (C), (D), (E), and (F) of this section will yield inaccurate 
results and that the proposed adaptation is appropriate.
    (vii) Leak detection methods for volatile organic material. Owners 
or operators required by the various subparts of this regulation to 
carry out a leak detection monitoring program shall comply with the 
following requirements:
    (A) Leak detection monitoring. (1) Monitoring shall comply with 40 
CFR part 60, appendix A. Method 21.
    (2) The detection instrument shall meet the performance criteria of 
Method 21.
    (3) The instrument shall be calibrated before use on each day of its 
use by the methods specified in Method 21.

[[Page 356]]

    (4) Calibration gases shall be:
    (i) Zero air (less than 10 ppm of hydrocarbon in air); and
    (ii) A mixture of methane or n-hexane and air at a concentration of 
approximately, but no less than, 10,000 ppm methane or n-hexane.
    (5) The instrument probe shall be traversed around all potential 
leak interfaces as close to the interface as possible as described in 
Method 21.
    (B) When equipment is tested for compliance with no detectable 
emissions as required, the test shall comply with the following 
requirements:
    (1) The requirements of paragraphs (a)(4) (vii)(A)(1) through 
(vii)(A)(5) of this section shall apply.
    (2) The background level shall be determined as set forth in Method 
21.
    (C) Leak detection tests shall be performed consistent with:
    (1) ``APTI Course SI 417 controlling Volatile Organic Compound 
Emissions from Leaking Process Equipment'' EPA-450/2-82-015 (which is 
available for purchase from the National Technical Information Services, 
5285 Port Royal Road, Springfield, VA 22161)
    (2) ``Portable Instrument User's Manual for Monitoring VOC Sources'' 
EPA-340/1-86-015 (which is available for purchase from the National 
Technical Information Services, 5285 Port Royal Road, Springfield, VA 
22161)
    (3) ``Protocols for Generating Unit-Specific Emission Estimates for 
Equipment Leaks of VOC and VHAP'' EPA-450/3-88-010 (which is available 
for purchase from the National Technical Information Services, 5285 Port 
Royal Road, Springfield, VA 22161)
    (4) ``Petroleum Refinery Enforcement Manual'' EPA-340/1-80-008 
(which is available for purchase from the National Technical Information 
Services, 5285 Port Royal Road, Springfield, VA 22161)
    (viii) Bulk gasoline delivery system test protocol. (A) The method 
for determining the emissions of gasoline from a vapor recovery system 
are delineated in 40 CFR part 60, subpart XX, Sec. 60.503.
    (B) Other tests shall be performed consistent with:
    (1) ``Inspection Manual for Control of Volatile Organic Emissions 
from Gasoline Marketing Operations: Appendix D'' EPA-340/1-80-012 (which 
is available for purchase from the National Technical Information 
Services, 5285 Port Royal Road, Springfield, VA 22161)
    (2) ``Control of Hydrocarbons from Tank Truck Gasoline Loading 
Terminals: Appendix A'' EPA-450/2-77-026 (which is available for 
purchase from the National Technical Information Services, 5285 Port 
Royal Road, Springfield, VA 22161)
    (5) Compliance dates. Compliance with the requirements of all rules 
is required by July 1, 1991, unless otherwise indicated by compliance 
dates contained in specific rules. This paragraph shall not operate to 
provide additional time for compliance under section 113(d) of the Act, 
42 U.S.C. 7413(d), for sources subject to compliance upon promulgation.
    (6) Afterburners. The operation of any natural gas fired afterburner 
and capture system used to comply with Sec. 52.741 is not required 
during the period of November 1 of any year to April 1 of the following 
year provided that the operation of such devices is not required for 
purposes of occupational safety or health, or for the control of toxic 
substances, odor nuisances, or other regulated pollutants.
    (7) Exemptions, variances, and alternative means of control or 
compliance determinations. Notwithstanding the provisions of any other 
paragraphs of this section, any exemptions, variances or alternatives to 
the control requirements, emission limitations, or test methods in the 
Illinois SIP or FIP can only be allowed if approved by the Administrator 
as a SIP or FIP revision.
    (8) Vapor pressure of volatile organic liquids. (i) If the VOL 
consists of only a single compound, the vapor pressure shall be 
determined by ASTM Method D2879-86 (incorporated by reference as 
specified in 40 CFR 52.742) or the vapor pressure may be obtained from a 
published source such as: Boublik, T., V. Fried and E. Hala, ``The Vapor 
Pressure of Pure Substances,'' Elsevier Scientific Publishing Co., New 
York (1973); Perry's Chemical Engineer's Handbook, McGraw-Hill Book 
Company (1984); CRC Handbook of Chemistry and Physics, Chemical Rubber 
Publishing Company (1986-87); and Lange's Handbook of Chemistry, John A. 
Dean, editor, McGraw-Hill Book Company (1985).

[[Page 357]]

    (ii) If the VOL is a mixture, the vapor pressure shall be determined 
by ASTM Method D2879-86 (incorporated by reference as specified in 40 
CFR 52.742) or by the following equation:
[GRAPHIC] [TIFF OMITTED] TC07NO91.001

where:

Pvol=Total vapor pressure of the mixture,
n=Number of components in the mixture,
i=Subscript denoting an individual component,
Pi=Vapor pressure of a component determined in accordance 
          with paragraph (a) of this section
Xi=Mole fraction of the component in the total mixture.

    (9) Vapor pressure of organic material or solvent. (i) If the 
organic material or solvent consists of only a single compound, the 
vapor pressure shall be determined by ASTM Method D2879-86 (incorporated 
by reference as specified in 40 CFR 52.742) or the vapor pressure may be 
obtained from a published source such as: Boublik, T., V. Fried and E. 
Hala, ``The Vapor Pressure of Pure Substances,'' Elsevier Scientific 
Publishing Co., New York (1973); Perry's Chemical Engineer's Handbook, 
McGraw-Hill Book Company (1984); CRC Handbook of Chemistry and Physics, 
Chemical Rubber Publishing Company (1986-87); and Lange's Handbook of 
Chemistry, John A. Dean, editor, McGraw-Hill Book Company (1985).
    (ii) If the organic material or solvent is in a mixture made up of 
both organic material compounds and compounds which are not organic 
material, the vapor pressure shall be determined by the following 
equation:
[GRAPHIC] [TIFF OMITTED] TC07NO91.002


where:

Pom=Total vapor pressure of the portion of the mixture which 
          is composed of organic material,
n=Number of organic material components in the mixture,
i=Subscript denoting an individual component,
Pi=Vapor pressure of an organic material component determined 
          in accordance with paragraph (a) of this section,
Xi=Mole fraction of the organic material component of the 
          total mixture.

    (iii) If the organic material or solvent is in a mixture made up of 
only organic material compounds, the vapor pressure shall be determined 
by ASTM Method D2879-86 (incorporated by reference as specified in 40 
CFR 52.742) or by the above equation.
    (10) Vapor pressure of volatile organic material. (i) If the VOM 
consists of only a single compound, the vapor pressure shall be 
determined by ASTM Method D2879-86 (incorporated by reference as 
specified in 40 CFR 52.742) or the vapor pressure may be obtained from a 
published source such as: Boublik, T., V. Fried and E. Hala, ``The Vapor 
Pressure of Pure Substances,'' Elsevier Scientific Publishing Co., New 
York (1973); Perry's Chemical Engineer's Handbook, McGraw-Hill Book 
Company (1984); CRC Handbook of Chemistry and Physics, Chemical Rubber 
Publishing Company (1986-87); and Lange's Handbook of Chemistry, John A. 
Dean, editor, McGraw-Hill Book Company (1985).
    (ii) If the VOM is in a mixture made up of both VOM compounds and 
compounds which are not VOM, the vapor pressure shall be determined by 
the following equation:
[GRAPHIC] [TIFF OMITTED] TC07NO91.003

2where:

Pvom=Total vapor pressure of the portion of the mixture which 
is composed of VOM,
n=Number of VOM components in the mixture,
i=Subscript denoting an individual component,
Pi=Vapor pressure of a VOM component determined in accordance 
with paragraph (a) of this section,
Xi=Mole fraction of the VOM component of the total mixture.

    (iii) If the VOM is in a mixture made up of only VOM compounds, the 
vapor pressure shall be determined by ASTM

[[Page 358]]

Method D2879-86 (incorporated by reference as specified in 40 CFR 
52.742) or by the above equation.
    (b)--(c) [Reserved]
    (d) Solvent cleaning--(1) Solvent cleaning in general. The 
requirements of subpart E (sections 215.182-215.184) of 35 Ill. Adm. 
Code 215 (incorporated by reference as specified in 40 CFR 52.742) shall 
apply to all cold cleaning, open top vapor degreasing, and conveyorized 
degreasing operations.


    Note: For Federal purposes, paragraph (d)(1) supersedes subpart E 
(section 215.181) of 35 Ill. Adm. Code 215.)


    (2) Compliance schedule. Every owner or operator of an emission 
source which was previously exempt from the requirements of subpart E 
(sections 215.182-215.184) of 35 Ill. Adm. Code 215 (incorporated by 
reference as specified in 40 CFR 52.742) because it satisfied the 
criteria in either (d)(a)(i) or (d)(2)(ii) of this section, shall comply 
with the requirements of subpart E (sections 215.182-215.184) of 35 Ill. 
Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742) 
on and after July 1, 1991. A source which did not satisfy the criteria 
in either (d)(a)(i) or (d)(2)(ii) of this section, shall comply with the 
requirements of subpart E (sections 215.182-215.184) of 35 Ill. Adm. 
Code 215 (incorporated by reference as specified in 40 CFR 52.742) upon 
promulgation.
    (i) If emissions of VOM exceed neither 6.8 kg (15 lbs) in any one 
day, nor 1.4 kg (3 lbs) in any one hour, or
    (ii) If the source is used exclusively for chemical or physical 
analysis or for determination of product quality and commercial 
acceptance, provided that the operation of the source is not an integral 
part of the production process, the emissions of VOM from the source do 
not exceed 363 kg (800 lbs) in any calendar month, and the exemption had 
been approved in writing by the Illinois Environmental Protection 
Agency.
    (3) Test methods. The following test methods shall be used to 
demonstrate compliance with subpart E (sections 215.182-215.184) of 35 
Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 
52.742):
    (i) Vapor pressures shall be determined by using the procedure 
specified in paragraph (a)(9) of this section.
    (ii) Exhaust ventilation rates shall be determined by using the 
procedures specified in paragraph (a)(4)(vi)(C) of this section.
    (iii) The performance of control devices shall be determined by 
using the procedures specified in paragraph (a)(4)(vi) of this section.
    (e) Coating operations--(1) Emission limitations for manufacturing 
plants. (i) Except as provided in paragraph (e)(3) of this section, no 
owner or operator of a coating line shall apply at any time any coating 
in which the VOM content exceeds the following emission limitations for 
the specified coating. The following emission limitations are expressed 
in units of VOM per volume of coating (minus water and any compounds 
which are specifically exempted from the definition of VOM) as applied 
at each coating applicator, except where noted. Compounds which are 
specifically exempted from the definition of VOM should be treated as 
water for the purpose of calculating the ``less water'' part of the 
coating composition. Compliance with this paragraph must be demonstrated 
through the applicable coating analysis test methods and procedures 
specified in paragraph (a)(4)(i) of this section and the recordkeeping 
and reporting requirements specified in paragraph (e)(6)(ii) of this 
section. As an alternative to compliance with this paragraph, the owner 
or operator of a coating line may meet the requirements of paragraph 
(e)(1)(ii) or paragraph (e)(2) of this section. The equation presented 
in paragraph (e)(1)(iii) of this section shall be used to calculate 
emission limitations for determining compliance by add-on controls, 
credits for transfer efficiency, emissions trades and cross-line 
averaging.

------------------------------------------------------------------------
                                                         kg/l    lb/gal
------------------------------------------------------------------------
(A) Automobile or Light-Duty Truck Coating
  (1) Prime coat......................................    0.14     (1.2)
  (2) Prime surfacer coat.............................    0.34     (2.8)

[[Page 359]]

    Note: The prime surfacer coat limitation is based upon a transfer
    efficiency of 30 percent. Transfer efficiency credits can only be
   allowed if approved by the Administrator as a SIP or FIP revision.
  (3) Topcoat.........................................    1.81    (15.1)
 Note: The topcoat limitation is in units of kg (lbs) of VOM per l (gal)
  of coating solids deposited. Compliance with the limitation shall be
 based on the daily-weighted average VOM content from the entire topcoat
  operation (all topcoat spray booths, flash-off areas and bake ovens).
Compliance shall be demonstrated in accordance with the topcoat protocol
for automobiles and light-duty trucks referenced in paragraph (a)(4)(ii)
 of this section. Paragraph (e)(1)(ii) of this section does not apply to
     the topcoat limitation.) At least 180 days prior to the initial
 compliance date, the owner or operator of a coating line subject to the
topcoat limitation shall submit to the Administrator a detailed proposal
specifying the method of demonstrating compliance with the protocol. The
 proposal shall include, at a minimum, a comprehensive plan (including a
rationale) for determining the transfer efficiency at each booth through
 the use of in-plant, or pilot testing; the selection of coatings to be
  tested (for the purpose of determining transfer efficiency) including
 the rationale for coating groupings; and the method for determining the
 analytic VOM content of as applied coatings and the formulation solvent
  content of as applied coatings. Upon approval of the protocol by the
Administrator, the source may proceed with the compliance demonstration.
  (4) Final repair coat...............................    0.58     (4.8)
(B) Can Coating
  (1) Sheet basecoat and overvarnish..................    0.34     (2.8)
  (2) Exterior basecoat and overvarnish...............    0.34     (2.8)
  (3) Interior body spray coat........................    0.51     (4.2)
  (4) Exterior end coat...............................    0.51     (4.2)
  (5) Side seam spray coat............................    0.66     (5.5)
  (6) End sealing compound coat.......................    0.44     (3.7)
(C) Paper Coating.....................................    0.35     (2.9)
   Note: The paper coating limitation shall not apply to any owner or
operator of any paper coating line on which printing is performed if the
 paper coating line complies with the emissions limitations in paragraph
            (h)(1) of this section: Printing and Publishing.
(D) Coil Coating......................................    0.31     (2.6)
(E) Fabric Coating....................................    0.35     (2.9)
(F) Vinyl Coating.....................................    0.45     (3.8)
(G) Metal Furniture Coating...........................    0.36     (3.0)
(H) Large Appliance Coating...........................    0.34     (2.8)
Note: The limitation shall not apply to the use of quick-drying lacquers
 for repair of scratches and nicks that occur during assembly, provided
 that the volume of coating does not exceed 0.95 l (1 quart) in any one
                       rolling eight-hour period.
(I) Magnet Wire Coating...............................    0.20     (1.7)
(J) Miscellaneous Metal Parts and Products Coating
  (1) Clear coating...................................    0.52     (4.3)
  (2) Air-dried coating...............................    0.42     (3.5)
  (3) Extreme performance coating.....................    0.42     (3.5)
  (4) Steel pail and drum interior coating............    0.52     (4.3)
  (5) All other coatings..............................    0.36     (3.0)
------------------------------------------------------------------------


------------------------------------------------------------------------
                                                         kg/l    lb/gal
------------------------------------------------------------------------
(K) Heavy Off-Highway Vehicle Products Coating
  (1) Extreme performance prime coat..................    0.42     (3.5)
  (2) Extreme performance top-coat (air dried)........    0.42     (3.5)
  (3) Final repair coat (air dried)...................    0.42     (3.5)
  (4) All other coatings are subject to the emission limitations for
   miscellaneous metal parts and products coatings in paragraph
   (e)(1)(i)(J) of this section.........................................
(L) Wood Furniture Coating
  (1) Clear topcoat...................................    0.67     (5.6)
  (2) Opaque stain....................................    0.56     (4.7)
  (3) Pigmented coat..................................    0.60     (5.0)
  (4) Repair coat.....................................    0.67     (5.6)
  (5) Sealer..........................................    0.67     (5.6)
  (6) Semi-transparent stain..........................    0.79     (6.6)
  (7) Wash coat.......................................    0.73     (6.1)
Note: An owner or operator of a wood furniture coating operation subject
  to this paragraph shall apply all coatings, with the exception of no
   more than 37.8 l (10 gal) of coating per day used for touch-up and
    repair operations, using one or more of the following application
  systems: airless spray application system, air-assisted airless spray
       application system, electrostatic spray application system,
   electrostatic bell or disc spray application system, heated airless
     spray application system, roller coating, brush or wipe coating
         application system, or dip coating application system.
(M) Existing Diesel-Electric Locomotive Coating Lines
 in Cook County
  (1) Extreme performance prime coat..................    0.42     (3.5)
  (2) Extreme performance top-coat (air dried)........    0.42     (3.5)
  (3) Final repair coat (air dried)...................    0.42     (3.5)
  (4) High-temperature aluminum coating...............    0.72     (6.0)
  (5) All other coatings..............................    0.36     (3.0)

[[Page 360]]

------------------------------------------------------------------------

    (ii) Daily-weighted average limitations. No owner or operator of a 
coating line subject to the limitations of paragraph (e)(1)(i) of this 
section and complying by means of paragraph (e)(1)(ii) of this section 
shall operate the subject coating line unless the owner or operator has 
demonstrated compliance with paragraph (e)(1) (ii)(A), (ii)(B), (ii)(C), 
(ii)(D), (ii)(E) or (ii)(F) of this section (depending upon the source 
category) through the applicable coating analysis test methods and 
procedures specified in paragraph (a)(4)(i) of this section and the 
recordkeeping and reporting requirements specified in paragraph 
(e)(6)(iii) of this section.
    (A) No owner or operator of a coating line subject to only one of 
the limitations from among paragraph (e)(1) (i)(A)(1), (i)(A)(2), 
(i)(A)(4), (i)(C), (i)(D), (i)(E), (i)(F), (i)(G), (i)(H), or (i)(I) of 
this section shall apply coating on any such coating line, during any 
day, whose daily-weighted average VOM content exceeds the emission 
limitation to which the coatings are subject.
    (B) No owner or operator of a miscellaneous metal parts and products 
coating line subject to the limitations of paragraph (e)(1)(i)(J) of 
this section shall apply coatings to miscellaneous metal parts or 
products on the subject coating line unless the requirements in 
paragraph (e)(1)(ii)(B) (1) or (2) of this section are met.
    (1) For each coating line which applies multiple coatings, all of 
which are subject to the same numerical emission limitation within 
paragraph (e)(1)(i)(J) of this section, during the same day (e.g., all 
coatings used on the line are subject to 0.42 kg/l [3.5 lbs/gal]), the 
daily-weighted average VOM content shall not exceed the coating VOM 
content limit corresponding to the category of coating used, or
    (2) For each coating line which applies coatings from more than one 
of the four coating categories in paragraph (e)(1)(i)(J) of this 
section, during the same day, the owner or operator shall submit to and 
receive approval from the Administrator for a site-specific FIP 
revision. To receive approval, the requirements of USEPA's Emissions 
Trading Policy Statement (and related policy) must be satisfied.
    (C) No owner or operator of a can coating facility subject to the 
limitations of pargraph (e)(1)(i)(B) of this section shall operate the 
subject coating facility using a coating with a VOM content in excess of 
the limitations specified in paragrpah (e)(1)(i)(B) of this section 
unless all of the following requirements are met:
    (1) An alternative daily emission limitation shall be determined 
according to paragraph (e)(1)(ii)(C)(2) of this section. Actual daily 
emissions shall never exceed the alternative daily emission limitation 
and shall be calculated by use of the following equation.
[GRAPHIC] [TIFF OMITTED] TC07NO91.004

where:

Ed=Actual VOM emissions for the day in units of kg/day (lbs/
          day),
i=Subscript denoting a specific coating applied,
n=Total number of coatings applied in the can coating operation,
Vi=Volume of each coating applied for the day in units of l/
          day (gal/day) of coating (minus water and any compounds which 
          are specifically exempted from the definition of VOM), and
Ci=The VOM content of each coating as applied in units of kg 
          VOM/l (lbs VOM/gal) of coating (minus water and any compounds 
          which are specifically exempted from the definition of VOM).

    (2) The alternative daily emission limitation (Ad) shall 
be determined on a daily basis as follows:
[GRAPHIC] [TIFF OMITTED] TC07NO91.005

where:

Ad=The VOM emissions allowed for the day in units of kg/day 
          (lbs/day),
i=Subscript denoting a specific coating applied,
n=Total number of surface coatings applied in the can coating operation,
Ci=The VOM content of each surface coating as applied in 
          units of kg VOM/l (lbs VOM/gal) of coating (minus water and 
          any compounds which are specifically exempted from the 
          definition of VOM),
Di=The density of VOM in each coating applied. For the 
          purposes of calculating Ad, the density is 0.882 kg 
          VOM/l VOM (7.36 lbs VOM/gal VOM),

[[Page 361]]

Vi=Volume of each surface coating applied for the day in 
          units of l (gal) of coating (minus water and any compounds 
          which are specifically exempted from the definition of VOM),
Li=The VOM emission limitation for each surface coating 
          applied as specified in paragraph (e)(1)(i)(B) of this section 
          in units of kg VOM/l (lbs VOM/gal) of coating (minus water and 
          any compounds which are specifically exempted from the 
          definition of VOM).

    (D) No owner or operator of a heavy off-highway vehicle products 
coating line subject to the limitations of paragraph (e)(1)(i)(K) of 
this section shall apply coatings to heavy off-highway vehicle products 
on the subject coating line unless the requirements of paragraph 
(e)(1)(ii)(D) (1) or (2) of this section are met.
    (1) For each coating line which applies multiple coatings, all of 
which are subject to the same numerical emission limitation within 
paragraph (e)(1)(i)(K) of this section, during the same day (e.g., all 
coatings used on the line are subject to 0.42 kg/l [3.5 lbs/gal]), the 
daily-weighted average VOM content shall not exceed the coating VOM 
content limit corresponding to the category of coating used, or
    (2) For each coating line which applies coatings subject to more 
than one numerical emission limitation in paragraph (e)(1)(i)(K) of this 
section, during the same day, the owner or operator shall submit to and 
receive approval from the Administrator for a site-specific FIP 
revision. To receive approval, the requirements of USEPA's Emissions 
Trading Policy Statement (and related policy) must be satisfied.
    (E) No owner or operator of a wood furniture coating line subject to 
the limitations of paragraph (e)(1)(i)(L) of this section shall apply 
coatings to wood furniture on the subject coating line unless the 
requirements of paragraph (e)(1)(ii)(E) (1) or (2) of this section, in 
addition to the requirements specified in the note to paragraph 
(e)(1)(i)(L) of this section, are met.
    (1) For each coating line which applies multiple coatings, all of 
which are subject to the same numerical emission limitation within 
paragraph (e)(1)(i)(L) of this section, during the same day (e.g., all 
coatings used on the line are subject to 0.67 kg/l [5.6 lbs/gal]), the 
daily-weighted average VOM content shall not exceed the coating VOM 
content limit corresponding to the category of coating used, or
    (2) For each coating line which applies coatings subject to more 
than one numerical emission limitation in paragraph (e)(1)(i)(L) of this 
section, during the same day, the owner or operator shall submit to and 
receive approval from the Administrator for a site-specific FIP 
revision. To receive approval, the requirements of USEPA's Emissions 
Trading Policy Statement (and related policy) must be satisfied.
    (F) No owner or operator of an existing diesel-electric locomotive 
coating line in Cook County, subject to the limitations of paragraph 
(e)(1)(i)(M) of this section shall apply coatings to diesel-electric 
locomotives on the subject coating line unless the requirements of 
paragraph (e)(1)(ii)(F) (1) or (2) of this section are met.
    (1) For each coating line which applies multiple coatings, all of 
which are subject to the same numerical emission limitation within 
paragraph (e)(1)(i)(M) of this section, during the same day (e.g., all 
coatings used on the line are subject to 0.42 kg/l [3.5 lbs/gal]), the 
daily-weighted average VOM content shall not exceed the coating VOM 
content limit corresponding to the category of coating used, or
    (2) For each coating line which applies coatings subject to more 
than one numerical emission limitation in paragraph (e)(1)(i)(M) of this 
section, during the same day, the owner or operator shall submit to and 
receive approval from the Administrator for a site-specific FIP 
revision. To receive approval, the requirements of USEPA's Emissions 
Trading Policy Statement (and related policy) must be satisfied.
    (iii) Limitations in terms of kg (lbs) of VOM emissions per l (gal) 
of solids as applied at each coating applicator shall be determined by 
the following equation:
[GRAPHIC] [TIFF OMITTED] TC07NO91.006

where:


[[Page 362]]


S=The limitation on VOM emissions in terms of kg VOM/l (lbs VOM/gal) of 
          solids,
C=The limitation on VOM emissions in terms of kg/l (lbs/gal) of coating 
          (minus water and any compounds which are specifically excluded 
          from the definition of VOM) specified in paragraph (e)(1)(i) 
          of this section,
D=The density of VOM in the coating. For the purposes of calculating S, 
          the density is 0.882 kg VOM/l VOM (7.36 lbs VOM/gal VOM).

    (2) Alternative emission limitations. Any owner or operator of a 
coating line subject to paragraph (e)(1) of this section may comply with 
this paragraph, rather than with paragraph (e)(1) of this section, if a 
capture system and control device are operated at all times and the 
owner or operator demonstrates compliance with paragraphs (e)(2) (ii), 
(iii), (iv), (v), (vi) or (vii) of this section (depending upon the 
source category) through the applicable coating analysis and capture 
system and control device efficiency test methods and procedures 
specified in paragraph (a)(4) of this section and the recordkeeping and 
reporting requirements specified in paragraph (e)(6)(iv) of this 
section; and the control device is equipped with the applicable 
monitoring equipment specified in paragraph (a)(4)(iv) of this section 
and the monitoring equipment is installed, calibrated, operated and 
maintained according to vendor specifications at all times the control 
device is in use. The use of a capture system and control device, which 
does not demonstrate compliance with paragraph (e)(2) (ii), (iii), (iv), 
(v), (vi), or (vii), may only be used as an alternative to compliance 
with paragraph (e)(1) of this section if approved as a FIP revision.
    (i) Alternative add-on control methodologies. (A) The coating line 
is equipped with a capture system and control device that provides 81 
percent reduction in the overall emissions of VOM from the coating line 
and the control device has a 90 percent efficiency, or
    (B) The system used to control VOM from the coating line is 
demonstrated to have an overall efficiency sufficient to limit VOM 
emissions to no more than what is allowed under paragraph (e)(1) of this 
section. Use of any control system other than an afterburner, carbon 
absorption, condensation, or absorption scrubber system can only be 
allowed if approved by the Administrator as a SIP or FIP revision. 
Transfer efficiency credits can only be allowed if approved by the 
Administrator as a SIP or FIP revision. Baseline transfer efficiencies 
and transfer efficiency test methods must be approved by the 
Administrator.
    Such overall efficiency is to be determined as follows:
    (1) Obtain the emission limitation from the appropriate paragraph in 
(e)(1) of this section,
    (2) Calculate ``S'' according to the equation in paragraph 
(e)(1)(iii) of this section,
    (3) Calculate the overall efficiency required according to paragraph 
(a)(4)(v) of this section. For the purposes of calculating this value, 
according to the equation in (a)(4)(v)(B) of this section 
VOM1 is equal to the value of ``S'' as determined above in 
(i)(B)(2).
    (ii) No owner or operator of a coating line subject to only one of 
the emission limitations from among paragraph (e)(1)(i)(A)(1), 
(e)(1)(i)(A)(2), (e)(1)(i)(A)(4), (e)(1)(i)(C), (e)(1)(i)(D), 
(e)(1)(i)(E), (e)(1)(i)(F), (e)(1)(i)(G), (e)(1)(i)(H), or (e)(1)(i)(I) 
of this section and equipped with a capture system and control device 
shall operate the subject coating line unless the requirements in 
paragraph (e)(2)(i) (A) or (B) of this section are met. No owner or 
operator of a coating line subject to paragraph (e)(1)(i)(A)(3) of this 
section and equipped with a capture system and control device shall 
operate the coating line unless the owner or operator demonstrates 
compliance with the topcoat limitation in accordance with the topcoat 
protocol for automobile or light-duty trucks referenced in paragraph 
(a)(4)(ii) of this section.
    (iii) No owner or operator of a miscellaneous metal parts and 
products coating line which applies one or more coatings during the same 
day, all of which are subject to the same numerical emission limitation 
within paragraph (e)(1)(i)(J) of this section (e.g., all coatings used 
on the line are subject to 0.42 kg/l [3.5 lbs/gal]), and which is 
equipped with a capture system and control device shall operate the 
subject

[[Page 363]]

coating line unless the requirements in paragraph (e)(2)(i) (A) or (B) 
of this section are met.
    (iv) No owner or operator of a heavy off-highway vehicle products 
coating line which applies one or more coatings during the same day, all 
of which are subject to the same numerical emission limitation within 
paragraph (e)(1)(i)(K) of this section (e.g., all coatings used on the 
line are subject to 0.42 kg/l [3.5 lbs/gal]), and which is equipped with 
a capture system and control device shall operate the subject coating 
line unless the requirements in paragraph (e)(2)(i) (A) or (B) of this 
section are met.
    (v) No owner or operator of an existing diesel-electric locomotive 
coating line in Cook County which applies one or more coatings during 
the same day, all of which are subject to the same numerical emission 
limitation within paragraph (e)(1)(i)(M) of this section (e.g., all 
coatings used on the line are subject to 0.42 kg/l [3.5 lbs/gals]), and 
which is equipped with a capture system and control device shall operate 
the subject coating line unless the requirements in paragraph (e)(2)(i) 
(A) or (B) of this section are met.
    (vi) No owner or operator of a wood furniture coating line which 
applies one or more coatings during the same day, all of which are 
subject to the same numerical emission limitation within paragraph 
(e)(1)(i)(L) (e.g., all coatings used on the line are subject to 0.67 
kg/l [5.6 lbs/gal]), and which is equipped with a capture system and 
control device shall operate the subject coating line unless the 
requirements in paragraph (e)(2)(i) (A) or (B) of this section are met. 
If compliance is achieved by meeting the requirements in paragraph 
(e)(2)(i)(B) of this section, then the provisions in the note to 
paragraph (e)(1)(i)(L) of this section must also be met.
    (vii) No owner or operator of a can coating facility and equipped 
with a capture system and control device shall operate the subject 
coating facility unless the requirements in paragraph (e)(2)(vii) (A) or 
(B) of this section are met.
    (A) An alternative daily emission limitation shall be determined 
according to paragraph (e)(1)(ii)(C)(2) of this section. Actual daily 
emissions shall never exceed the alternative daily emission limitation 
and shall be calculated by use of the following equation:
[GRAPHIC] [TIFF OMITTED] TC07NO91.007

where:

Ed=Actual VOM emissions for the day in units of kg/day (lbs/
          day),
i=Subscript denoting the specific coating applied,
n=Total number of surface coatings as applied in the can coating 
          operation,
Vi=Volume of each coating as applied for the day in units of 
          1/day (gal/day) of coating (minus water and any compounds 
          which are specifically exempted from the definition of VOM),
Ci=The VOM content of each coating as applied in units of kg 
          VOM/l (lbs VOM/gal) of coating (minus water and any compounds 
          which are specifically exempted from the definition of VOM), 
          and
Fi=Fraction, by weight, of VOM emissions from the surface 
          coating, reduced or prevented from being emitted to the 
          ambient air. This is the overall efficiency of the capture 
          system and control device.

    (B) The coating line is equipped with a capture system and control 
device that provide 75 percent reduction in the overall emissions of VOM 
from the coating line and the control device has a 90 percent 
efficiency.
    (3) Exemptions from emission limitations--(i) Exemptions for all 
source categories except wood furniture coating. The limitations of 
paragraph (e) of this section shall not apply to coating lines within a 
facility, that otherwise would be subject to the same subparagraph of 
paragraph (e)(1)(i) of this section (because they belong to the same 
source category, e.g. can coating), provided that combined actual 
emissions of VOM from all lines at the facility subject to that 
subparagraph never exceed 6.8 kg/day (15 lbs/day) before the application 
of capture systems and control devices. (For example, can coating lines 
within a plant would not be subject to the limitations of subparagraph 
(e)(1)(i)(B) of this section if the combined actual emissions of VOM 
from the can coating lines never exceed 6.8

[[Page 364]]

kg/day (15 lbs/day) before the application of capture systems and 
control devices.) Volatile organic material emissions from heavy off-
highway vehicle products coating lines must be combined with VOM 
emissions from miscellaneous metal parts and products coating lines to 
determine applicability. Any owner or operator of a coating facility 
shall comply with the applicable coating analysis test methods and 
procedures specified in paragraph (a)(4)(i) of this section and the 
recordkeeping and reporting requirements specified in paragraph 
(e)(6)(i) of this section if total VOM emissions from the subject 
coating lines are always less than or equal to 6.8 kg/day (15 lbs/day) 
before the application of capture systems and control devices and, 
therefore, are not subject to the limitations of paragraph (e)(1) of 
this section. Once a category of coating lines at a facility is subject 
to the limitations in paragraph (e)(1) of this section, the coating 
lines are always subject to the limitations in paragraph (e)(1) of this 
section.
    (ii) Applicability for wood furniture coating. (A) The limitations 
of paragraph (e) of this section shall apply to a plant's wood furniture 
coating lines if the plant contains process emission sources, not 
regulated by paragraphs (d), (e) (excluding paragraph (e)(1)(i)(L)), (h) 
(excluding paragraph (h)(5)), (i), (j), or (q)(1), or subparts B, Q 
(excluding sections 215.432 and 215.436), R (excluding sections 215.447, 
215.450, and 215.452), S, V, X, Y (sections 215.582-215.584), or Z of 35 
Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 
52.742), which as a group both:
    (1) Have maximum theoretical emissions of 91 Mg (100 tons) or more 
per calendar year of VOM if no air pollution control equipment were 
used, and
    (2) Are not limited to less than 91 Mg (100 tons) of VOM per 
calendar year if no air pollution control equipment were used, through 
production or capacity limitations contained in a federally enforceable 
construction permit or SIP or FIP version.
    (B) If a plant ceases to fulfill the criteria of paragraph 
(e)(3)(ii)(A) of this section, the limitations of paragraph (e)(1)(i)(L) 
of this section shall continue to apply to any wood furniture coating 
line which was ever subject to the limitations of paragraph (e)(1)(i)(L) 
of this section.
    (C) For the purposes of paragraph (e)(3)(ii) of this section, an 
emission source shall be considered regulated by a subpart (of the 
Illinois rules), section, or paragraph if it is subject to the 
limitations of that subpart (of the Illinois rules), section, or 
paragraph. An emission source is not considered regulated by a subpart 
(of the Illinois rules), section, or paragraph if its emissions are 
below the applicability cutoff level or if the source is covered by an 
exemption.
    (D) Any owner or operator of a wood furniture coating line to which 
the limitations of paragraph (e) of this section are not applicable due 
to the criteria in paragraph (e)(3)(ii) of this section shall, upon 
request by the Administrator, submit records to the Administrator within 
30 calendar days from the date of the request that document that the 
coating line is exempt from the limitations of paragraph (e) of this 
section.
    (4) Exemption from general rule on use of organic material. No owner 
or operator of a coating line subject to the limitations of paragraph 
(e)(1) of this section is required to meet the limitations of subpart K 
(section 215.301 or 215.302) of 35 Ill. Adm. Code 215 (incorporated by 
reference as specified in 40 CFR 52.742), after the date by which the 
coating line is required to meet paragraph (e)(1) of this section.
    (5) Compliance schedule. Except as specified in paragraph (e)(7) of 
this section, every owner or operator of a coating line (of a type 
included within paragraph (e)(1)(i) of this section) shall comply with 
the requirements of paragraph (e)(1),(e)(2) or (e)(3) of this section 
and paragraph (e)(6) of this section in accordance with the appropriate 
compliance schedule as specified in paragraph (e)(5)(i),(ii),(iii) or 
(iv) of this section.
    (i) No owner or operator of a coating line which is exempt from the 
limitations of paragraph (e)(1) of this section because of the criteria 
in paragraph (e)(3)(i) of this section shall operate said coating line 
on or after July 1, 1991, unless the owner or operator has

[[Page 365]]

complied with, and continues to comply with, paragraph (e)(6)(i) of this 
section. Wood furniture coating lines are not subject to paragraph 
(e)(6)(i) of this section.
    (ii) No owner or operator of a coating line complying by means of 
paragraph (e)(1)(i) of this section shall operate said coating line on 
or after July 1, 1991, unless the owner or operator has complied with, 
and continues to comply with, paragraphs (e)(1)(i) and (e)(6)(ii) of 
this section.
    (iii) No owner or operator of a coating line complying by means of 
paragraph (e)(1)(ii) of this section shall operate said coating line on 
or after July 1, 1991, unless the owner or operator has complied with, 
and continues to comply with, paragraphs (e)(1)(ii) and (e)(6)(iii) of 
this section.
    (iv) No owner or operator of a coating line complying by means of 
paragraph (e)(2) of this section shall operate said coating line on or 
after July 1, 1991, unless the owner or operator has complied with, and 
continues to comply with, paragraphs (e)(2) and (e)(6)(iv) of this 
section.
    (6) Recordkeeping and reporting. The VOM content of each coating and 
the efficiency of each capture system and control device shall be 
determined by the applicable test methods and procedures specified in 
paragraph (a)(4) of this section to establish the records required under 
paragraph (e)(6) of this section.
    (i) Any owner or operator of a coating line which is exempted from 
the limitations of paragraph (e)(1) of this section because of paragraph 
(e)(3)(i) of this section shall comply with the following:
    (A) By July 1, 1991, the owner or operator of a facility referenced 
in paragraph (e)(6)(i) of this section shall certify to the 
Administrator that the facility is exempt under the provisions of 
paragraph (e)(3)(i) of this section. Such certification shall include:
    (1) A declaration that the facility is exempt from the limitations 
of paragraph (e)(1) of this section because of paragraph (e)(3)(i) of 
this section; and
    (2) Calculations which demonstrate that the combined VOM emissions 
from all coating lines at the facility never exceed 6.8 kg (15 lbs) per 
day before the application of capture systems and control devices. The 
following equation shall be used to calculate total VOM emissions:
[GRAPHIC] [TIFF OMITTED] TC07NO91.008

where:

Te=Total VOM emissions from coating lines at a facility each 
          day before the application of capture systems and control 
          devices in units of kg/day (lbs/day),
m=Number of coating lines at the facility,
j=Subscript denoting an individual coating line,
n=Number of different coatings as applied each day on each coating line 
          at the facility,
i=Subscript denoting an individual coating,
Ai=Weight of VOM per volume of each coating (minus water and 
          any compounds which are specifically exempted from the 
          definition of VOM) as applied each day on each coating line at 
          the facility in units of kg VOM/l (lbs VOM/gal), and
Bi=Volume of each coating (minus water and any compounds 
          which are specifically exempted from the definition of VOM) as 
          applied each day on each coating line at the facility in units 
          of l/day (gal/day). The instrument or method by which the 
          owner or operator accurately measured or calculated the volume 
          of each coating as applied on each coating line each day shall 
          be described in the certification to the Administrator.

    (B) On and after July 1, 1991, the owner or operator of a facility 
referenced in paragraph (e)(6)(i) of this section shall collect and 
record all of the following information each day for each coating line 
and maintain the information at the facility for a period of three 
years:
    (1) The name and identification number of each coating as applied on 
each coating line.
    (2) The weight of VOM per volume and the volume of each coating 
(minus water and any compounds which are specifically exempted from the 
definition of VOM) as applied each day on each coating line.
    (C) On and after July 1, 1991, the owner or operator of a facility 
exempted from the limitations of paragraph (e)(1) of this section 
because of paragraph (e)(3)(i) of this section shall notify the 
Administrator of any record showing that total VOM emissions

[[Page 366]]

from the coating facility exceed 6.8 kg (15 lbs) in any day before the 
application of capture systems and control devices shall be reported by 
sending a copy of such record to the Administrator within 30 days after 
the exceedance occurs.
    (ii) Any owner or operator of a coating line subject to the 
limitations of paragraph (e)(1) of this section and complying by means 
of paragraph (e)(1)(i) of this section shall comply with the following:
    (A) By July 1, 1991, or upon initial start-up of a new coating line, 
or upon changing the method of compliance from an existing subject 
coating line from paragraph (e)(1)(ii) or paragraph (e)(2) to paragraph 
(e)(1)(i) of this section; the owner or operator of a subject coating 
line shall certify to the Administrator that the coating line will be in 
compliance with paragraph (e)(1)(i) of this section on and after July 1, 
1991, or on and after the initial start-up date. Such certification 
shall include:
    (1) The name and identification number of each coating as applied on 
each coating line.
    (2) The weight of VOM per volume of each coating (minus water and 
any compounds which are specifically exempted from the definition of 
VOM) as applied each day on each coating line.
    (3) For coating lines subject to paragraph (e)(1)(i)(A)(3) of this 
section, certification shall include:
    (i) The name and identification number of each coating line which 
will comply by means of paragraph (e)(1)(i)(A)(3) of this section,
    (ii) The name and identification number of each coating as applied 
on each coating line,
    (iii) The weight of VOM per volume of each coating as applied on 
each coating line,
    (iv) The instrument or method by which the owner or operator will 
accurately measure or calculate the volume of each coating as applied 
each day on each coating line,
    (v) The method by which the owner or operator will create and 
maintain records each day as required in paragraph (e)(6)(ii)(B) of this 
section for coating lines subject to paragraph (e)(1)(i)(A)(3) of this 
section,
    (vi) An example format in which the records required in paragraph 
(e)(6)(ii)(B) of this section for coating lines subject to paragraph 
(e)(1)(i)(A)(3) of this section.
    (B) On and after July 1, 1991, or on and after the initial start-up 
date, the owner or operator of a coating line subject to the limitations 
of paragraph (e)(1) of this section and complying by means of paragraph 
(e)(1)(i) of this section shall collect and record all of the following 
information each day for each coating line and maintain the information 
at the facility for a period of three years:
    (1) The name and identification number of each coating as applied on 
each coating line.
    (2) The weight of VOM per volume of each coating (minus water and 
any compounds which are specifically exempted from the definition of 
VOM) as applied each day on each coating line.
    (3) For coating lines subject to paragraph (e)(1)(i)(A)(3) of this 
section, the owner or operator shall maintain all records necessary to 
calculate the daily-weighted average VOM content from the coating line 
in accordance with the proposal submitted, and approved by the 
Administrator, pursuant to paragraph (e)(1)(A)(3) of this section.
    (C) On and after July 1, 1991, the owner or operator of a subject 
coating line shall notify the Administrator in the following instances:
    (1) Any record showing violation of paragraph (e)(1)(i) of this 
section shall be reported by sending a copy of such record to the 
Administrator within 30 days following the occurrence of the violation, 
except that any record showing a violation of paragraph (e)(1)(i)(A)(3) 
of this section shall be reported by sending a copy of such record to 
the Administrator within 15 days from the end of the month in which the 
violation occurred.
    (2) At least 30 calendar days before changing the method of 
compliance with paragraph (e)(1) of this section from paragraph 
(e)(1)(i) to paragraph (e)(1)(ii) or paragraph (e)(2) of this section, 
the owner or operator shall comply with all requirements of paragraph 
(e)(6) (iii)(A) or (iv)(A) of this section, respectively. Upon changing 
the method of compliance with paragraph (e)(1)

[[Page 367]]

of this section from paragraph (e)(1)(i) to paragraph (e)(1)(ii) or 
paragraph (e)(2) of this section, the owner or operator shall comply 
with all requirements of paragraph (e)(6) (iii) or (iv) of this section, 
respectively.
    (3) For coating lines subject to paragraph (e)(1)(i)(A)(3) of this 
section, the owner or operator shall notify the Administrator of any 
change to the topcoating operation at least 30 days before the change is 
effected. The Administrator shall determine whether or not 
recertification testing is required. If the Administrator determines 
that recertification testing is required, then the owner or operator 
shall submit a proposal to the Administrator to test within 30 days and 
retest within 30 days of the Administrator's approval of the proposal.
    (iii) Any owner or operator of a coating line subject to the 
limitations of paragraph (e)(1) of this section and complying by means 
of paragraph (e)(1)(ii) of this section shall comply with the following:
    (A) By July 1, 1991, or upon initial start-up of a new coating line, 
or upon changing the method of compliance for an existing subject 
coating line from paragraph (e)(1)(i) or paragraph (e)(2) to paragraph 
(e)(1)(ii) of this section; the owner or operator of the subject coating 
line shall certify to the Administrator that the coating line will be in 
compliance with paragraph (e)(1)(ii) of this section on and after July 
1, 1991, or on and after the initial start-up date. Such certification 
shall include:
    (1) The name and identification number of each coating line which 
will comply by means of paragraph (e)(1)(ii) of this section.
    (2) The name and identification number of each coating as applied on 
each coating line.
    (3) The weight of VOM per volume and the volume of each coating 
(minus water and any compounds which are specifically exempted from the 
definition of VOM) as applied each day on each coating line.
    (4) The instrument or method by which the owner or operator will 
accurately measure or calculate the volume of each coating as applied 
each day on each coating line.
    (5) The method by which the owner or operator will create and 
maintain records each day as required in paragraph (e)(6)(iii)(B) of 
this section.
    (6) An example of the format in which the records required in 
paragraph (e)(6)(iii)(B) of this section will be kept.
    (B) On and after July 1, 1991, or on and after the initial start-up 
date, the owner or operator of a coating line subject to the limitations 
of paragraph (e)(1) of this section and complying by means of paragraph 
(e)(1)(ii) of this section, shall collect and record all of the 
following information each day for each coating line and maintain the 
information at the facility for a period of three years:
    (1) The name and identification number of each coating as applied on 
each coating line.
    (2) The weight of VOM per volume and the volume of each coating 
(minus water and any compounds which are specifically exempted from the 
definition of VOM) as applied each day on each coating line.
    (3) The daily-weighted average VOM content of all coatings as 
applied on each coating line as defined in paragraph (a)(3) of this 
section.
    (C) On and after July 1, 1991, the owner or operator of a subject 
coating line shall notify the Administrator in the following instances:
    (1) Any record showing violation of paragraph (e)(1)(ii) of this 
section shall be reported by sending a copy of such record to the 
Administrator within 30 days following the occurrence of the violation.
    (2) At least 30 calendar days before changing the method of 
compliance with paragraph (e) from paragraph (e)(1)(ii) to paragraph 
(e)(1)(i) or paragraph (e)(2) of this section, the owner or operator 
shall comply with all requirements of paragraph (e)(6)(ii)(A) or 
(iv)(A), respectively. Upon changing the method of compliance with 
paragraph (e) from paragraph (e)(1)(ii) to paragraph (e)(1)(i) or 
paragraph (e)(2) of this section, the owner or operator shall comply 
with all requirements of paragraph (e)(6)(ii) or (iv), respectively.
    (iv) Any operator or owner of a coating line subject to the 
limitations of paragraph (e)(2) of this section and

[[Page 368]]

complying by means of paragraph (e)(2)(ii), (iii), (iv), (v), (vi) or 
(vii) of this section shall comply with the following:
    (A) By July 1, 1991, or upon initial start-up of a new coating line, 
or upon changing the method of compliance for an existing coating line 
from paragraph (e)(1) (i) or (ii) to paragraph (e)(2) of this section; 
the owner or operator of the subject coating line shall perform all 
tests and submit to the Administrator the results of all tests and 
calculations necessary to demonstrate that the subject coating line will 
be in compliance with paragraph (e)(2) of this section on and after July 
1, 1991, or on and after the initial start-up date.
    (B) On and after July 1, 1991, or on and after the initial start-up 
date, the owner or operator of a coating line subject to the limitations 
of paragraph (e)(2) of this section and complying by means of paragraph 
(e)(2) (ii), (iii), (iv), (v), (vi) or (vii) of this section shall 
collect and record all of the following information each day for each 
coating line and maintain the information at the facility for a period 
of three years:
    (1) The weight of VOM per volume of coating solids as applied each 
day on each coating line, if complying pursuant to paragraph 
(e)(2)(i)(B) of this section.
    (2) Control device monitoring data.
    (3) A log operating time for the capture system, control device, 
monitoring equipment and the associated coating line.
    (4) A maintenance log for the capture system, control device and 
monitoring equipment detailing all routine and non-routine maintenance 
performed including dates and duration of any outages.
    (C) On and after July 1, 1991, the owner or operator of a subject 
coating line shall notify the Administrator in the following instances:
    (1) Any record showing violation of paragraph (e)(2) of this section 
shall be reported by sending a copy of such record to the Administrator 
within 30 days following the occurrence of the violation.
    (2) At least 30 calendar days before changing the method of 
compliance with paragraph (e) from paragraph (e)(2) to paragraph 
(e)(1)(i) or paragraph (e)(1)(ii) of this section, the owner or operator 
shall comply with all requirements of paragraph (e)(6)(ii)(A) or 
(iii)(A) of this section, respectively. Upon changing the method of 
compliance with paragraph (e) from paragraph (e)(2) to paragraph 
(e)(1)(i) or paragraph (e)(1)(ii) of this section, the owner or operator 
shall comply with all requirements of paragraph (e)(6)(ii) or (iii) of 
this section, respectively.
    (7) Compliance schedule for diesel electric locomotive coatings. 
Notwithstanding any other provision of this subpart, the compliance date 
for the emission limitations and standards for ``topcoat'' and ``final 
repair coat'' operations only as applied to General Motors Corporation 
at their diesel electric locomotive coating lines in Cook County, 
Illinois, codified at 40 CFR 52.741(e)(1)(i)(M) (2) and (3) is specified 
in this paragraph (e)(7). Compliance with the requirements of paragraph 
(e)(1), (e)(2) or (e)(3) of this section and paragraph (e)(6) of this 
section must be in accordance with the appropriate compliance schedule 
as specified in paragraph (e)(7)(i),(ii),(iii), or (iv) of this section.
    (i) No owner or operator of a coating line which is exempt from the 
limitations of paragraph (e)(1) of this section because of the criteria 
in paragraph (e)(3)(i) of this section shall operate said coating line 
on or after March 25, 1995, unless the owner or operator has complied 
with, and continues to comply with, paragraph (e)(6)(i) of this section.
    (ii) No owner or operator of a coating line complying by means of 
paragraph (e)(1)(i) of this section shall operate said coating line on 
or after March 25, 1995, unless the owner or operator has complied with, 
and continues to comply with, paragraph (e)(1)(i) and (e)(6)(ii) of this 
section.
    (iii) No owner or operator of a coating line complying by means of 
paragraph (e)(1)(ii) of this section shall operate said coating line on 
or after March 25, 1995, unless the owner or operator has complied with, 
and continues to comply with, paragraphs (e)(1)(ii) and (e)(6)(iii) of 
this section.
    (iv) No owner or operator of a coating line complying by means of 
paragraph

[[Page 369]]

(e)(2) of this section shall operate said coating line on or after March 
25, 1995, unless the owner or operator has complied with, and continues 
to comply with, paragraphs (e)(2) and (e)(6)(iv) of this section.
    (8) The control requirements in this paragraph apply to the wood 
coating line, which coats wooden globe stand components, at Replogle 
Globes, Inc. (Replogle) Broadview facility in Cook County, Illinois, 
instead of the control requirements in paragraphs (e)(1) and (e)(2) of 
this section. Compliance with this paragraph must be demonstrated 
through the applicable coating analysis test methods and procedures 
specified in paragraph (a)(4)(i) of this section.
    (i) After October 6, 1991, no coatings shall at any time be applied 
which exceed the following emission limitations for the specified 
coating.
    (A) 6.59 pounds (lbs) Volatile Organic Material (VOM) per gallon of 
stain (minus water and any compounds which are specifically exempted 
from the definition of VOM) as applied to coat wooden globe stand 
components. Such stain consists of #9250 Walnut NGR Stain (RGI # 
W06000100), #9974 Cherry NGR Stain (RGI # W06003500) and #9943 Ash NGR 
Stain (RGI # W06003600). The Administrator must be notified at least ten 
(10) days prior to the use of any replacement stains.
    (B) 5.53 lbs VOM per gallon of Sanding Sealer (minus water and any 
compounds which are specifically exempted from the definition of VOM) as 
applied to coat wooden globe stand components. Such sealer consists of 
#15304 High Build Sanding Sealer (RGI # W06003700). The Administrator 
must be notified at least ten (10) days prior to the use of any 
replacement sanding sealer.
    (C) 5.20 lbs VOM per gallon of lacquer (minus water and any 
compounds which are specifically exempted from the definition of VOM) as 
applied to coat wooden globe stand components. Such lacquer consists of 
#15352 High Build Lacquer (RGI # W06003300). The Administrator shall be 
notified at least ten (10) days prior to the use of any replacement 
lacquer.
    (ii) After October 6, 1991, the volume of coatings used shall not 
exceed the following:
    (A) 5,000 gallons per year total for all coatings specified in 
paragraph (e)(8)(i)(A) of this section. The yearly volume of coatings 
used are to be calculated as follows:
    (1) Compute the volume of specified coating used each month by the 
15th of the following month.
    (2) By the 15th of each month, add the monthly coating use for the 
12 previous months (to obtain the yearly volume of coatings used).
    (B) 4,000 gallons per year total for all coatings specified in 
paragraph (e)(8)(i)(B) of this section. The yearly volume of the 
coatings used are to be calculated as specified in paragraphs 
(e)(8)(ii)(A)(1) and (e)(8)(ii)(A)(2) of this section.
    (C) 5,000 gallons per year total for all coatings specified in 
paragraph (e)(8)(i)(C) of this section. The yearly volume of coatings 
used are to be calculated as specified in paragraphs (e)(8)(ii)(A)(1) 
and (e)(8)(ii)(A)(2) of this section.
    (iii) Beginning on October 6, 1991, the owner and operator of the 
Replogle Globes, Inc. plant in Broadview, Illinois shall keep the 
following records for each month. All records shall be retained at 
Replogle Globes, Inc. for three (3) years and shall be made available to 
the Administrator on request.
    (A) the name and identification number of each coating as applied on 
any wood coating line.
    (B) The weight of VOM per volume (determined in accordance with the 
procedures in paragraph (a)(4)(i) of this section) and the volume of 
each coating (minus water and any compounds which are specifically 
exempted from the definition of VOM) as applied each month on any wood 
coating line.
    (9) [Reserved]
    (10) Until December 31, 1996, the control and recordkeeping 
requirements in this paragraph apply to the three solvent-based 
polyester paper coating lines (Lines C, D and E) at Riverside 
Laboratories' Kane County, Illinois facility, instead of the control 
requirements in paragraphs (e)(1) and (e)(2) of this section and the 
recordkeeping requirements in paragraph (e)(6) of this section. 
Compliance with this paragraph must be demonstrated through the 
applicable coating analysis test

[[Page 370]]

methods and procedures specified in paragraph (a)(4)(i) of this section. 
The requirements in paragraphs (e)(1), (e)(2), and (e)(6) of this 
section shall apply to Riverside on and after December 31, 1996.
    (i) After December 21, 1995, no coatings shall at any time be 
applied on Lines C, D or E which exceed 3.5 pounds (lbs.) volatile 
organic material (VOM) per gallon of coating (minus water and any 
compounds which are specifically exempted from the definition of VOM), 
except as provided in paragraph (e)(10)(ii) of this section.
    (ii) After December 21, 1995, the following specifically identified 
coatings may exceed 3.5 lbs. VOM per gallon of coating (minus water and 
any compounds which are specifically exempted from the definition of 
VOM) only if they are applied on Line E and they do not exceed the 
limits indicated below (minus water and any compounds which are 
specifically exempted from the definition of VOM):

EXP-5027--4.34 lbs./gallon
PD 75 CLR--4.19 lbs./gallon
PD 75 BRN--4.18 lbs./gallon
SQZ-54--3.88 lbs./gallon
SPX-34GL--3.51 lbs./gallon

    (iii) That portion of Riverside's polyester production which is 
manufactured with the use of any VOC, from Lines C, D, and E, may not 
exceed the following levels: 35 million square feet per year during and 
after 1992, 29 million square feet per year during and after 1994, and 
25 million square feet during 1996. Compliance with this requirement 
shall be determined by adding the polyester production from any 12 
consecutive months during and after the years indicated, through 1996. 
That is, the polyester production for any 12 consecutive months starting 
with January 1992 cannot exceed 35 million square feet; the polyester 
production from any 12 consecutive months starting with January 1994 
cannot exceed 29 million square feet; and the polyester production for 
the twelve months from January through December 1996 cannot exceed 25 
million square feet. Only those square feet of polyester whose 
production involves the use of VOC need to be restricted by the 
production levels in this paragraph (e)(10)(iii) of this section.
    (iv) By December 21, 1995, Riverside shall certify to the 
Administrator that its polyester coating operations will be in 
compliance with paragraphs (e)(10)(i), (e)(10)(ii), and (e)(10)(iii) of 
this section. Such certification shall include the following:
    (A) The name and identification number of each coating as applied on 
coating lines C, D and E.
    (B) The weight of VOM per volume of each coating (minus water and 
any compounds which are specifically exempted from the definition of 
VOM) as applied on each coating line.
    (v) The Administrator must be notified at least 10 days prior to the 
use of any polyester coating not previously identified pursuant to 
paragraph (e)(10)(iv) of this section. This notification must include 
the information specified in paragraphs (e)(10)(iv)(A) and 
(e)(10)(iv)(B) of this section.
    (vi) On and after December 21, 1995, Riverside shall collect and 
record all of the following information each day for each coating and 
maintain the information at the facility for a period of 3 years:
    (A) The name and identification number of each coating as applied.
    (B) The weight of VOM per volume of each coating (minus water and 
any compounds which are specifically exempted from the definition of 
VOM) as applied each day.
    (C) Any record showing a VOM content in excess of the emission 
limits in paragraph (e)(10)(i) or (e)(10)(ii) of this section shall be 
reported by sending a copy of such record to the Administrator within 30 
days following its collection.
    (D) Any VOM besides acetone used in any coating must be identified.
    (vii) Starting with the first full month after December 21, 1995, 
Riverside shall collect and record the figures on polyester production 
(in square feet), for each month and maintain the information at the 
facility for a period of at least 3 years.
    (viii) Regardless of any other provision of paragraph (e)(10) of 
this section, after August 21, 1995 no coating which contains any VOM 
other than acetone shall at any time be applied on Line C, D, or E which 
exceeds 2.9 lbs. VOM per gallon of coating (minus water and any

[[Page 371]]

compounds which are specifically exempted from the definition of VOM).
    (f)--(g) [Reserved]
    (h) Printing and publishing--(1) Flexographic and rotogravure 
printing. (i) No owner or operator of a subject flexographic, packaging 
rotogravure or publication rotogravure printing line shall apply at any 
time any coating or ink unless the VOM content does not exceed the 
limitation specified in either paragraph (h)(1)(i)(A) or (B) of this 
section. Compliance with this paragraph must be demonstrated through the 
applicable coating or ink analysis test methods and procedures specified 
in paragraph (a)(4)(i) of this section and the recordkeeping and 
reporting requirements specified in paragraph (h)(4)(ii) of this 
section. As an alternative to compliance with paragraph (h)(1)(i) of 
this section, a subject printing line may meet the requirements of 
paragraph (h)(1)(ii) or (iii) of this section.
    (A) Forty percent VOM by volume of the coating and ink (minus water 
and any compounds which are specifically exempted from the definition of 
VOM), or
    (B) Twenty-five percent VOM by volume of the volatile content in the 
coating and ink.
    (ii) No owner or operator of a subject flexographic, packaging 
rotogravure or publication rotogravure printing line shall apply 
coatings or inks on the subject printing line unless the weighted 
average, by volume, VOM content of all coatings and inks as applied each 
day on the subject printing line does not exceed the limitation 
specified in either paragraph (h)(1)(i)(A) (as determined by paragraph 
(h)(1)(ii)(A) or (h)(1)(i)(B) (as determined by paragraph (h)(1)(ii)(B) 
of this section. Compliance with this paragraph must be demonstrated 
through the applicable coating or ink analysis test methods and 
procedures specified in paragraph (a)(4)(i) of this section and the 
recordkeeping and reporting requirements specified in paragraph 
(h)(4)(iii) of this section.
    (A) The following equation shall be used to determine if the 
weighted average VOM content of all coatings and inks as applied each 
day on the subject printing line exceeds the limitation specified in 
paragraph (h)(1)(i)(A) of this section.
[GRAPHIC] [TIFF OMITTED] TC07NO91.009

where:

VOM(i)(A)=The weighted average VOM content in units of 
          percent VOM by volume of all coatings and inks (minus water 
          and any compounds which are specifically exempted from the 
          definition of VOM) used each day,
i=Subscript denoting a specific coating or ink as applied,
n=The number of different coatings and/or inks as applied each day on a 
          printing line,
Ci=The VOM content in units of percent VOM by volume of each 
          coating or ink as applied (minus water and any compounds which 
          are specifically exempted from the defintion of VOM),
Li=The liquid volume of each coating or ink as applied in 
          units of l (gal),
Vsi=The volume fraction of solids in each coating or ink as 
          applied, and
VVOMi=The volume fraction of VOM in each coating or ink as 
          applied.

    (B) The following equation shall be used to determine if the 
weighted average VOM content of all coatings and inks as applied each 
day on the subject printing line exceeds the limitation specified in 
paragraph (h)(1)(i)(B) of this section.
[GRAPHIC] [TIFF OMITTED] TC07NO91.010

where:

    VOM(i)(B)=The weighted average VOM content in units of 
percent VOM by volume of the volatile content of all coatings and inks 
used each day,
    i=Subscript denoting a specific coating or ink as applied,
    n=The number of different coatings and/or inks as applied each day 
on each printing line,
    Ci=The VOM content in units of percent VOM by volume of 
the volatile matter in each coating or ink as applied,
    Li=The liquid volume of each coating or ink as applied in 
units of l (gal), and

[[Page 372]]

    VVMi=The volume fraction of volatile matter in each 
coating or ink as applied.

    (iii) No owner or operator of a subject flexographic, packaging 
rotogravure or publication rotogravure printing line equipped with a 
capture system and control device shall operate the subject printing 
line unless the owner or operator meets the requirements in paragraph 
(h)(1)(iii) (A), (B) or (C) and paragraphs (h)(1)(iii) (D), (E) and (F) 
of this section.
    (A) A carbon adsorption system is used which reduces the captured 
VOM emissions by at least 90 percent by weight, or
    (B) An incineration system is used which reduces the captured VOM 
emissions by at least 90 percent by weight, or
    (C) An alternative VOM emission reduction system is demonstrated to 
have at least a 90 percent control device efficiency and the alternative 
emission reduction system is approved by the Administrator as a SIP or 
FIP revisions, and
    (D) The printing line is equipped with a capture system and control 
device that provides an overall reduction in VOM emissions of at least:
    (1) 75 percent where a publication rotogravure printing line is 
employed, or
    (2) 65 percent where a packaging rotogravure printing line is 
employed, or
    (3) 60 percent where a flexographic printing line is employed, and
    (E) The control device is equipped with the applicable monitoring 
equipment specified in paragraph (a)(4)(iv)(B) of this section and the 
monitoring equipment is installed, calibrated, operated and maintained 
according to vendor specifications at all times the control device is in 
use, and
    (F) The capture system and control device are operated at all times 
when the subject printing line is in operation. The owner or operator 
shall demonstrate compliance with this paragraph by using the applicable 
capture system and control device test methods and procedures specified 
in paragraphs (a)(4) (iii) through (vi) of this section and by complying 
with the recordkeeping and reporting requirements specified in paragraph 
(h)(4)(iv) of this section.
    (2) Applicability. (i) The limitations of paragraph (h)(1) of this 
section apply to all flexographic and rotogravure printing lines at a 
subject facility. All facilities with flexographic and/or rotogravure 
printing lines are subject facilities unless:
    (A) Total maximum theoretical emissions of VOM from all flexographic 
and rotogravure printing line(s) at the facility never exceed 90.7 Mg 
(100 tons) per calendar year before the application of capture systems 
and control devices, or
    (B) A federally enforceable construction permit or SIP or FIP 
revision for all flexographic and rotogravure printing line(s) at a 
facility requires the owner or operator to limit production or capacity 
of these printing line(s) to reduce total VOM emissions from all 
flexographic and rotogravure printing line(s) to 90.7 Mg (100 tons) or 
less per calendar year before the application of capture systems and 
control devices.
    (ii) Upon achieving compliance with paragraph (h) of this section, 
the emission source is not required to meet subpart K (sections 215.301 
or 215.302) of 35 Ill. Adm. Code 215 (incorporated by reference as 
specified in 40 CFR 52.742). Emission sources exempt from paragraph (h) 
of this section are subject to subpart K (sections 215.301 or 215.302). 
Rotogravure or flexographic equipment used for both roll printing and 
paper coating are subject to paragraph (h) of this section.
    (iii) Once subject to the limitations of paragraph (h)(1) of this 
section, a flexographic or rotogravure printing line is always subject 
to the limitations of paragraph (h)(1) of this section.
    (iv) Any owner or operator of any flexographic or rotogravure 
printing line that is exempt from the limitations of paragraph (h)(1) of 
this section because of the criteria in paragraph (h)(2) of this section 
is subject to the recordkeeping and reporting requirements specified in 
paragraph (h)(4)(i) of this section.
    (3) Compliance schedule. Every owner or operator of a flexographic 
and/or rotogravure printing line shall comply with the applicable 
requirements of paragraph (h)(1) of this section and

[[Page 373]]

paragraph (h)(4) of this section in accordance with the applicable 
compliance schedule specified in paragraph (h)(3) (i), (ii), (iii) or 
(iv) of this section.
    (i) No owner or operator of a flexographic or rotogravure printing 
line which is exempt from the limitations of paragraph (h)(1) of this 
section because the criteria in paragraph (h)(2) of this section shall 
operate said printing line on or after July 1, 1991, unless the owner or 
operator has complied with, and continues to comply with, paragraph 
(h)(4)(i) of this section.
    (ii) No owner or operator of a flexographic or rotogravure printing 
line complying by means of paragraph (h)(1)(i) of this section shall 
operate said printing line on or after July 1, 1991, unless the owner or 
operator has complied with, and continues to comply with, paragraphs 
(h)(1)(i) and (h)(4)(ii) of this section.
    (iii) No owner or operator of a flexographic or rotogravure printing 
line complying by means of paragraph (h)(1)(ii) of this section shall 
operate said printing line on or after July 1, 1991, unless the owner or 
operator has complied with, and continues to comply with, paragraphs 
(h)(1)(ii) and (h)(4)(iii) of this section.
    (iv) No owner or operator of a flexographic or rotogravure printing 
line complying by means of paragraph (h)(1)(iii) of this section shall 
operate said printing line on or after July 1, 1991, unless the owner or 
operator has complied with, and continues to comply with, paragraphs 
(h)(1)(iii) and (h)(4)(iv) of this section.
    (4) Recordkeeping and reporting. The VOM content of each coating and 
ink and the efficiency of each capture system and control device shall 
be determined by the applicable test methods and procedures specified in 
paragraph (a)(4) of this section to establish the records required under 
paragraph (h)(4) of this section.
    (i) Any owner or operator of a printing line which is exempted from 
the limitations of paragraph (h)(1) of this section because of the 
criteria in paragraph (h)(2) of this section shall comply with the 
following:
    (A) By July 1, 1991, the owner or operator of a facility to which 
paragraph (h)(4)(i) of this section is applicable shall certify to the 
Administrator that the facility is exempt under the provisions of 
paragraph (h)(2) of this section. Such certification shall include:
    (1) A declaration that the facility is exempt from the limitations 
of the criteria in paragraph (h)(1) of this section because of paragraph 
(h)(2) of this section, and
    (2) Calculations which demonstrate that total maximum theoretical 
emissions of VOM from all flexographic and rotogravure printing lines at 
the facility never exceed 90.7 Mg (100 tons) per calendar year before 
the application of capture systems and control devices. Total maximum 
theoretical emissions of VOM for a flexograhpic or rotogravure printing 
facility is the sum of maximum theoretical emissions of VOM from each 
flexographic and rotogravure printing line at the facility. The 
following equation shall be used to calculate total maximum theoretical 
emissions of VOM per calendar year before the application of capture 
systems and control devices for each flexographic and rotogravure 
printing line at the facility:

                          Ep=A x  B

where:
    Ep=Total maximum theoretical emissions of VOM from one 
flexographic or rotogravure printing line in units of kg/year (lbs/
year),
    A=Weight of VOM per volume of solids of the coating or ink with the 
highest VOM content as applied each year on the printing line in units 
of kg VOM/l (lbs VOM/gal) of coating or ink solids, and
    B=Total volume of solids for all coatings and inks that can 
potentially be applied each year on the printing line in units of l/year 
(gal/year). The instrument and/or method by which the owner or operator 
accurately measured or calculated the volume of each coating and ink as 
applied and the amount that can potentially be applied each year on the 
printing line shall be described in the certification to the 
Administrator.

    (B) On and after July 1, 1991, the owner or operator of a facility 
referenced in paragraph (h)(4)(i) of this section shall collect and 
record all of the following information each year for each printing line 
and maintain the information at the facility for a period of three 
years:

[[Page 374]]

    (1) The name and identification number of each coating and ink as 
applied on each printing line.
    (2) The VOM content and the volume of each coating and ink as 
applied each year on each printing line.
    (C) On and after July 1, 1991, the owner or operator of a facility 
exempted from the limitations of paragraph (h)(1) of this section 
because of the criteria in paragraph (h)(2) of this section shall notify 
the Administrator of any record showing that total maximum theoretical 
emissions of VOM from all printing lines exceed 90.7 Mg (100 tons) in 
any calendar year before the application of capture systems and control 
devices, shall be reported by sending a copy of such record to the 
Administrator within 30 days after the exceedance occurs.
    (ii) Any owner or operator of a printing line subject to the 
limitations of paragraph (h)(1) of this section and complying by means 
of paragraph (h)(1)(i) of this section shall comply with the following:
    (A) By July 1, 1991, or upon initial start-up of a new printing 
line, or upon changing the method of compliance from an existing subject 
printing line from paragraph (h)(1) (ii) or (iii) of this section to 
paragraph (h)(1)(i) of this section, the owner or operator of a subject 
printing line shall certify to the Administrator that the printing line 
will be in compliance with paragraph (h)(1)(i) of this section on and 
after July 1, 1991, or on and after the initial start-up date. Such 
certification shall include:
    (1) The name and identification number of each coating and ink as 
applied on each printing line.
    (2) The VOM content of each coating and ink as applied each day on 
each printing line.
    (B) On and after July 1, 1991, or on and after the initial start-up 
date, the owner or operator of a printing line subject to the 
limitations of paragraph (h)(1) of this section and complying by means 
of paragraph (h)(1)(i) of this section shall collect and record all of 
the following information each day for each coating line and maintain 
the information at the facility for a period of three years:
    (1) The name and identification number of each coating and ink as 
applied on each printing line.
    (2) The VOM content of each coating and ink as applied each day on 
each printing line.
    (C) On and after July 1, 1991, the owner or operator of a subject 
printing line shall notify the Administrator in the following instances:
    (1) Any record showing violation of paragraph (h)(1)(i) of this 
section shall be reported by sending a copy of such record to the 
Administrator within 30 days following the occurrence of the violation.
    (2) At least 30 calendar days before changing the method of 
compliance with paragraph (h)(1) of this section from paragraph 
(h)(1)(i) of this section to paragraph (h)(1) (ii) or (iii) of this 
section, the owner or operator shall comply with all requirements of 
paragraph (h)(4) (iii)(A) or (iv)(A) of this section respectively. Upon 
changing the method of compliance with paragraph (h)(1) from paragraph 
(h)(1)(i) to paragraph (h)(1) (ii) or (iii) of this section, the owner 
or operator shall comply with all requirements of paragraph (h)(4) (iii) 
or (iv) of this section, respectively.
    (iii) Any owner or operator of a printing line subject to the 
limitations of paragraph (h)(1) of this section and complying by means 
of paragraph (h)(1)(ii) of this section shall comply with the following:
    (A) By July 1, 1991, or upon initial start-up of a new printing 
line, or upon changing the method of compliance for an existing subject 
printing line from paragraph (h)(1) (i) or (iii) of this section to 
paragraph (h)(1)(ii) of this section, the owner or operator of the 
subject printing line shall certify to the Administrator that the 
printing line will be in compliance with paragraph (h)(1)(ii) of this 
section on and after July 1, 1991, or on and after the initial start-up 
date. Such certification shall include:
    (1) The name and identification number of each printing line which 
will comply by means of paragraph (h)(1)(ii) of this section.
    (2) The name and identification number of each coating and ink 
available for use on each printing line.

[[Page 375]]

    (3) The VOM content of each coating and ink as applied each day on 
each printing line.
    (4) The instrument or method by which the owner or operator will 
accurately measure or calculate the volume of each coating and ink as 
applied each day on each printing line.
    (5) The method by which the owner or operator will create and 
maintain records each day as required in paragraph (h)(4)(iii)(B) of 
this section.
    (6) An example of the format in which the records required in 
paragraph (h)(4)(iii)(B) of this section will be kept.
    (B) On and after July 1, 1991, or on and after the initial start-up 
date, the owner or operator of a printing line subject to the 
limitations of paragraph (h)(1) of this section and complying by means 
of paragraph (h)(1)(ii) of this section shall collecting line and 
maintain the information at the facility for a period of three years:
    (1) The name and identification number of each coating and ink as 
applied on each printing line.
    (2) The VOM content and the volume of each coating and ink as 
applied each day on each printing line.
    (3) The daily-weighted average VOM content of all coatings and inks 
as applied on each printing line.
    (C) On and after July 1, 1991, the owner or operator of a subject 
printing line shall notify the Administrator in the following instances:
    (1) Any record showing violation of paragraph (h)(1)(ii) of this 
section shall be reported by sending a copy of such record to the 
Administrator within 30 days following the occurrence of the violation.
    (2) At least 30 calendar days before changing the method of 
compliance with paragraph (h)(1) of this section from paragraph 
(h)(1)(ii) to paragraph (h)(1)(i) or (iii) of this section, the owner or 
operator shall comply with all requirements of paragraph (h)(4)(ii)(A) 
or (iv)(A), respectively. Upon changing the method of compliance with 
paragraph (h)(1) from paragraph (h)(1)(ii) to paragraph (h)(1)(i) or 
(iii), the owner or operator shall comply with all requirements of 
paragraph (h)(4)(ii) or (iv) of this section, respectively.
    (iv) Any owner or operator of a printing line subject to the 
limitations of paragraph (h)(1) of this section and complying by means 
of paragraph (h)(1)(iii) of this section shall comply with the 
following:
    (A) By July 1, 1991, or upon initial start-up of a new printing 
line, or upon changing the method of compliance for an existing printing 
line from paragraph (h)(1)(i) or (ii) of this section to paragraph 
(h)(1)(iii) of this section, the owner or operator of the subject 
printing line shall perform all tests and submit to the Administrator 
the results of all tests and calculations necessary to demonstrate that 
the subject printing line will be in compliance with paragraph 
(h)(1)(iii) of this section on and after July 1, 1991, or on and after 
the initial start-up date.
    (B) On and after July 1, 1991, or on and after the initial start-up 
date, the owner or operator of a printing line subject to the 
limitations of paragraph (h)(1) of this section and complying by means 
of paragraph (h)(1)(iii) of this section shall collect and record all of 
the following information each day for each printing line and maintain 
the information at the facility for a period of three years:
    (1) Control device monitoring data.
    (2) A log of operating time for the capture system, control device, 
monitoring equipment and the associated printing line.
    (3) A maintenance log for the capture system, control device and 
monitoring equipment detailing all routine and non-routine maintenance 
performed including dates and duration of any outages.
    (C) On and after July 1, 1991, the owner or operator of a subject 
printing line shall notify the Administration in the following 
instances:
    (1) Any record showing violation of paragraph (h)(1)(iii) of this 
section shall be reported by sending a copy of such record to the 
Administrator within 30 days following the occurrence of the violation.
    (2) At least 30 calendar days before changing the method of 
compliance with paragraph (h)(1) from paragraph (h)(1)(iii) to paragraph 
(h)(1) (i) or (ii), the owner or operator shall comply with all 
requirements of paragraph

[[Page 376]]

(h)(4) (ii)(A) or (iii)(A) of this section, respectively. Upon changing 
the method of compliance with paragraph (h)(1) from paragraph 
(h)(1)(iii) to paragraph (h)(1) (i) or (ii) of this section, the owner 
or operator shall comply with all requirements of paragraph (h)(4) (ii) 
or (iii) of this section, respectively.
    (5) Heatset-web-offset lithographic printing--(i) Applicability. (A) 
The limitations of paragraph (h)(5)(ii) of this section apply to all 
heatset-web-offset lithographic printing lines at a subject facility. 
All facilities with heatset-web-offset lithographic printing lines are 
subject facilities unless:
    (1) Total maximum theoretical emissions of VOM from all heatset-web-
offset lithographic printing lines at the facility never exceed 90.7 Mg 
(100 tons) per calendar year in the absence of air pollution control 
equipment, or
    (2) A federally enforceable construction permit or SIP or FIP 
revision for all heatset-web-offset lithographic printing line(s) at a 
facility requires the owner or operator to limit production or capacity 
of these printing line(s) to reduce total VOM emissions from all 
heatset-web-offset lithographic printing line(s) to 90.7 Mg (100 tons) 
per calendar year or less in the absence of air pollution control 
equipment, and
    (B) Any owner or operator of any heatset-web-offset lithographic 
printing line that is exempt from the limitations in paragraph 
(h)(5)(ii) of this section because of the criteria in paragraph 
(h)(5)(i)(A) of this section shall be subject to the recordkeeping and 
reporting requirements in paragraph (h)(5)(iii)(A) of this section.
    (ii) Specific provisions. No owner or operator of a subject heatset-
web-offset printing line may cause or allow the operation of the subject 
heatset-web-offset printing line unless the owner or operator meets the 
requirements in paragraph (h)(5)(ii) (A) or (B) of this section and the 
requirements in paragraphs (h)(5)(ii) (C) and (D) of this section.
    (A) An afterburner system is installed and operated that reduces 90 
percent of the VOM emissions from the dryer exhaust, or
    (B) The fountain solution contains no more than 8 percent, by 
weight, of VOM and a condensation recovery system is installed and 
operated that removes at least 75 percent of the non-isopropyl alcohol 
organic materials from the dryer exhaust, and
    (C) The control device is equipped with the applicable monitoring 
equipment specified in paragraph (a)(4)(iv)(B) of this section and the 
monitoring equipment is installed, calibrated, operated and maintained 
according to vendor specifications at all times the control device is in 
use, and
    (D) The control device is operated at all times when the subject 
printing line is in operation. The owner or operator shall demonstrate 
compliance with paragraph (h)(5) of this section by using the applicable 
test methods and procedures specified in paragraphs (a)(4) (i), (iv), 
and (vi) of this section and by complying with the recordkeeping and 
reporting requirements specified in paragraph (h)(5)(iii) of this 
section.
    (iii) Recordkeeping and reporting. The VOM content of each fountain 
solution and ink and the efficiency of each control device shall be 
determined by the applicable test methods and procedures specified in 
paragraph (a)(4) of this section to establish the records required under 
paragraph (h)(5)(iii) of this section.
    (A) Any owner or operator of a printing line which is exempted from 
the limitations of paragraph (h)(5)(ii) of this section because of the 
criteria in paragraph (h)(5)(i) of this section shall comply with the 
following:
    (1) By July 1, 1991, the owner or operator of a facility to which 
paragraph (h)(5)(iii)(A) of this section is applicable shall certify to 
the Administrator that the facility is exempt under the provisions of 
paragraph (h)(5)(i) of this section. Such certification shall include:
    (i) A declaration that the facility is exempt from the limitations 
of paragraph (h)(5)(ii) of this section because of the criteria in 
paragraph (h)(5)(i) of this section, and
    (ii) Calculations which demonstrate that total maximum theoretical 
emissions of VOM from all heatset-web-offset lithographic printing lines 
at the facility never exceed 90.7 Mg (100 tons)

[[Page 377]]

per calendar year before the application of air pollution control 
equipment. Total maximum theoretical emissions of VOM for a heatset-web-
offset lithographic printing facility is the sum of maximum theoretical 
emissions of VOM from each heatset-web-offset lithographic printing line 
at the facility. The following equation shall be used to calculate total 
maximum theoretical emissions of VOM per calendar year in the absence of 
air pollution control equipment for each heatset-web-offset lithographic 
printing line at the facility.
[GRAPHIC] [TIFF OMITTED] TC07NO91.011


where

Ep=Total maximum theoretical emissions of VOM from one 
          heatset-web-offset printing line in units of kg/year (lbs/
          year),
A=Weight of VOM per volume of solids of ink with the highest VOM content 
          as applied each year on the printing line in units of kg VOM/l 
          (lbs VOM/gal) of solids, and
B=Total volume of solids for all inks that can potentially be applied 
          each year on the printing line in units of l/year (gal/year). 
          The instrument or method by which the owner or operator 
          accurately measured or calculated the volume of each ink as 
          applied and the amount that can potentially be applied each 
          year on the printing line shall be described in the 
          certification to the Administrator.
C=The weight percent VOM of the fountain solution with the highest VOM 
          content.
D=The total volume of fountain solution that can potentially be used 
          each year on the printing line in units of l/year (gal/year). 
          The instrument and/or method by which the owner or operator 
          accurately measured or calculated the volume of each fountain 
          solution used and the amount that can potentially be used each 
          year on the printing line shall be described in the 
          certification to the Administrator.

    (2) On and after July 1, 1991, the owner or operator of a facility 
to which paragraph (h)(5)(iii)(A) of this section is applicable shall 
collect and record all of the following information each year for each 
printing line and maintain the information at the facility for a period 
of three years:
    (i) The name and identification of each fountain solution and ink as 
applied on each printing line.
    (ii) The VOM content and the volume of each fountain solution and 
ink as applied each year on each printing line.
    (3) On and after July 1, 1991, the owner or operator of a facility 
exempted from the limitations of paragraph (h)(5)(ii) of this section 
because of the criteria in paragraph (h)(5)(i) of this section shall 
notify the Administrator of any record showing that total maximum 
theoretical emissions of VOM from all printing lines exceed 90.7 Mg (100 
tons) in any calendar year in the absence of air pollution control 
equipment shall be reported by sending a copy of such record to the 
Administrator within 30 days after the exceedance occurs.
    (B) Any owner or operator of a printing line subject to the 
limitations of paragraph (h)(5)(ii) of this section and complying by 
means of paragraph (h)(5)(ii)(A) of this section shall comply with the 
following:
    (1) By July 1, 1991, or upon initial start-up of a new printing 
line, or upon changing the method of compliance for an existing printing 
line from paragraph (h)(5) (ii)(B) to (ii)(A) of this section, the owner 
or operator of the subject printing line shall perform all tests and 
submit to the Administrator the results of all tests and calculations 
necessary to demonstrate that the subject printing line will be in 
compliance with paragraph (h)(5)(ii)(A) of this section on and after 
July 1, 1991, or on and after the initial start-up date.
    (2) On and after July 1, 1991, or on and after the initial start-up 
date, the owner or operator of a printing line subject to the 
limitations of paragraph (h)(5)(ii) of this section and complying by 
means of paragraph (h)(5)(ii)(A) of this section shall collect and 
record the following information each day for each printing line and 
maintain the information at the facility for a period of three years:
    (i) Control device monitoring data.
    (ii) A log of operating time for the control device, monitoring 
equipment and the associated printing line.
    (iii) A maintenance log for the control device and monitoring 
equipment detailing all routine and nonroutine maintenance performed 
including dates and duration of any outages.

[[Page 378]]

    (3) On and after July 1, 1991, the owner or operator of a subject 
printing line shall notify the Administrator in the following instances:
    (i) Any record showing violation of paragraph (h)(5)(ii)(A) of this 
section shall be reported by sending a copy of such record to the 
Administrator within 30 days following the occurrence of the violation.
    (ii) At least 30 calendar days before changing the method of 
compliance with paragraph (h)(5)(ii) of this section from paragraph 
(h)(5) (ii)(A) to (ii)(B), the owner or operator shall comply with all 
requirements of paragraph (h)(5)(iii)(C)(1) of this section. Upon 
changing the method of compliance with paragraph (h)(5)(ii) from 
paragraph (h)(5) (ii)(A) to (ii)(B) of this section the owner or 
operator shall comply with all requirements of paragraph (h)(5)(iii)(C) 
of this section.
    (C) Any owner or operator of a printing line subject to the 
limitations of paragraph (h)(5)(ii) of this section and complying by 
means of paragraph (h)(5)(ii)(B) of this section shall comply with the 
following:
    (1) By July 1, 1991, or upon initial start-up of a new printing 
line, or upon changing the method of compliance for an existing printing 
line from paragraph (h)(5) (ii)(A) to (ii)(B) of this section, the owner 
or operator of the subject printing line shall perform all tests and 
submit to the Administrator the results of all tests and calculations 
necessary to demonstrate that the subject printing line will be in 
compliance with paragraph (h)(5)(ii)(B) of this section on and after 
July 1, 1991, or on and after the initial start-up date.
    (2) On and after July 1, 1991, or on and after the initial start-up 
date, the owner or operator of a printing line subject to the 
limitations of paragraph (h)(5)(ii) of this section and complying by 
means of paragraph (h)(5)(ii)(B) of this section shall collect and 
record the following information each day for each printing line and 
maintain the information at the facility for a period of three years:
    (i) The VOM content of the fountain solution used each day on each 
printing line.
    (ii) A log of operating time for the control device and the 
associated printing line.
    (iii) A maintenance log for the control device detailing all routine 
and non-routine maintenance performed including dates and duration of 
any outages.
    (3) On and after July 1, 1991, the owner or operator of a subject 
printing line shall notify the Administrator in the following instances:
    (i) Any record showing violation of paragraph (h)(5)(ii)(B) of this 
section shall be reported by sending a copy of such record to the 
Administrator within 30 days following the occurrence of the violation.
    (ii) At least 30 calendar days before changing the method of 
compliance with paragraph (h)(5)(ii) of this section from paragraph 
(h)(5)(ii)(B) to (h)(5)(ii)(A) of this section, the owner or operator 
shall comply with all requirements of paragraph (h)(5)(iii)(B)(1) of 
this section. Upon changing the method of compliance with paragraph 
(h)(5)(ii) of this section from paragraph (h)(5)(ii)(B) to (h)(5)(ii)(A) 
of this section, the owner or operator shall comply with all 
requirements of paragraph (h)(5)(iii)(B) of this section.
    (iv) Compliance schedule. Every owner or operator of a heatset-web-
offset lithographic printing line shall comply with the applicable 
requirements of paragraphs (h)(5) (ii) and (iii) of this section in 
accordance with the applicable compliance schedule specified in 
paragraph (h)(5)(iv) (A), (B) or (C) of this section.
    (A) No owner or operator of a heatset-web-offset lithographic 
printing line which is exempt from the limitations of paragraph 
(h)(5)(ii) of this section because of the criteria in paragraph 
(h)(5)(i) of this section shall operate said printing line on or after 
July 1, 1991, unless the owner or operator has complied with, and 
continues to comply with, paragraphs (h)(5)(iii)(A) and (h)(5)(ii)(A) of 
this section.
    (B) No owner or operator of a heatset-web-offset lithographic 
printing line complying by means of paragraph (h)(5)(ii)(A) of this 
section shall operate said printing line on or after July 1, 1991, 
unless the owner or operator has complied with, and continues

[[Page 379]]

to comply with, paragraphs (h)(5)(iii)(B) and (h)(5)(ii)(B) of this 
section.
    (C) No owner or operator of a heatset-web-offset lithographic 
printing line complying by means of paragraph (h)(5)(ii)(B) of this 
section shall operate said printing line on or after July 1, 1991, 
unless the owner or operator has complied with, and continues to comply 
with, paragraph (h)(5)(iii)(C) of this section.
    (6) The control and recordkeeping and reporting requirements, as 
well as the test methods in this paragraph, apply to the rotogravure and 
flexographic presses at General Packaging Products, Inc.'s (GPP) plant 
in Chicago, Illinois, instead of the requirements in 40 CFR 52.741(h)(1) 
through 40 CFR 52.741(h)(5).
    (i) After July 1, 1992, no inks or other volatile organic material 
(VOM) containing materials shall at any time be applied or used which 
have a higher percent VOM by weight than the following:
    (A) 8 percent VOM by weight for waterbased inks as applied on GPP's 
presses.
    (B) 82 percent VOM by weight for solvent based inks as applied on 
GPP's presses.
    (C) 100 percent VOM by weight for all other VOM containing materials 
(besides inks) as used on GPP's presses.
    (ii) After July 1, 1992, the weight of ink and other VOM containing 
materials used shall not exceed the following:
    (A) 200,000 pounds per year total for all waterbased inks, as 
applied (including dilution material). The yearly weight of waterbased 
inks used is to be calculated according to the procedure in paragraph 
(h)(6)(iii) of this section.
    (B) 100,008 pounds per year total for all solvent based inks, as 
applied (including dilution material). The yearly weight of solvent 
based inks used is to be calculated according to the procedure in 
paragraph (h)(6)(iii) of this section.
    (C) 100,000 pounds per year total (based upon the formulation of the 
material as it is used on the presses) for all other VOM containing 
materials (besides inks). The yearly weight of other VOM containing 
materials is to be calculated according to the procedure in paragraph 
(h)(6)(iii) of this section.
    (iii) The yearly weight of ink/material used is to be calculated as 
follows:
    (A) Compute the weight of ink/material used each month by the 15th 
of the following month.
    (B) By the 15th of each month, add the monthly ink/material usage 
for the 12 previous months (to obtain the yearly weight of ink/material 
used).
    (iv) Beginning on July 1, 1992, the owner and operator of GPP's 
plant in Chicago, Illinois, shall keep the following records for each 
month. All records shall be retained at GPP for 3 years and shall be 
made available to the Administrator on request:
    (A) The name and identification number of each waterbased ink, each 
solvent based ink, and each other VOM containing material as applied or 
used on any press.
    (B) The pounds of waterbased ink as applied on all presses for each 
month and the percent VOM by weight for each waterbased ink as applied 
on any press for each month.
    (C) The pounds of solvent based ink as applied on all presses for 
each month and the percent VOM by weight for each solvent based ink as 
applied on any press for each month.
    (D) The pounds of other (non-ink) VOM containing material used on 
all presses for each month and the percent VOM by weight for each (non-
ink) VOM containing material as used on any press for each month.
    (v) Any record showing a violation of paragraph (h)(6)(i) or 
(h)(6)(ii) of this section shall be reported by sending a copy of such 
record to the Administrator within 30 days of the violation.
    (vi) To determine compliance with paragraphs (h)(6)(i) and 
(h)(6)(ii) of this section and to establish the records required under 
paragraph (h)(6)(iv) of this section the percent VOM by weight of each 
ink and other VOM containing material shall be determined by the 
applicable test methods and procedures specified in paragraph (a)(4) of 
this section.
    (i) Leaks from synthetic organic chemical and polymer manufacturing 
equipment--(1) Inspection program for leaks. The owner or operator of a 
synthetic

[[Page 380]]

organic chemical or polymer manufacturing plant subject to paragraph (i) 
and subpart Q (sections 215.430, 215.431, 215.433, 215.434, 215.435, and 
215.437) of Ill. Adm. Code 215 (incorporated by reference as specified 
in 40 CFR 52.742) shall, for the purposes of detecting leaks, conduct a 
component inspection program using the test methods specified in Method 
21, 40 CFR part 60, appendix A, consistent with the following 
provisions:
    (i) Test annually those components operated near extreme temperature 
or pressure such that they would be unsafe to routinely monitor and 
those components which would require the elevation of monitoring 
personnel higher than two meters above permanent worker access 
structures or surfaces.
    (ii) Test quarterly all other pressure relief valves in gas service, 
pumps in light liquid service, valves in light liquid service and in gas 
service, and compressors.
    (iii) If less than or equal to 2 percent of the valves in light 
liquid service and in gas service tested pursuant to paragraph 
(i)(1)(ii) of this section are found not to leak for five consecutive 
quarters, no leak tests shall be required for three consecutive 
quarters. Thereafter, leak tests shall resume for the next quarter. If 
that test shows less than or equal to 2 percent of the valves in light 
liquid service and in gas service are leaking, then no tests are 
required for the next three quarters. If more than 2 percent are 
leaking, then tests are required for the next five quarters.
    (iv) Observe visually all pump seals weekly.
    (v) Test immediately any pump seal from which liquids are observed 
dripping.
    (vi) Test any relief valve within 24 hours after it has vented to 
the atmosphere.
    (vii) Routine instrument monitoring of valves which are not 
externally regulated, flanges, and equipment in heavy liquid service, is 
not required. However, any valve which is not externally regulated, 
flange or piece of equipment in heavy liquid service that is found to be 
leaking on the basis of sight, smell or sound shall be repaired as soon 
as practicable but no later than 30 days after the leak is found.
    (viii) Test immediately after repair any component that was found 
leaking.
    (ix) Within one hour of its detection, a weatherproof, readily 
visible tag, in bright colors such as red or yellow, bearing an 
identification number and the date on which the leak was detected must 
be affixed on the leaking component and remain in place until the 
leaking component is repaired.
    (x) The following components are exempt from the monitoring 
requirements in paragraph (i)(1) of this section:
    (A) Any component that is in vacuum service, and
    (B) Any pressure relief valve that is connected to an operating 
flare header or vapor recovery device.
    (2) Alternative program for leaks. The Administrator shall approve 
an alternative program of monitoring, recordkeeping, or reporting to 
that prescribed in paragraph (i) and subpart Q (sections 215.430, 
215.431, 215.433, 215.434, 215.435, and 215.437) of Ill. Adm. Code 215 
(incorporated by reference as specified in 40 CFR 52.742), upon a 
demonstration by the owner or operator of such plant that the 
alternative program will provide plant personnel and USEPA personnel 
with an equivalent ability to identify and repair leaking components. 
Any alternative program can only be allowed if approved by the 
Administrator as a SIP or FIP revision.
    (j) Petroleum refining and related industries: asphalt materials--
(1) Monitoring program for leaks. (i) The owner or operator of a 
petroleum refinery subject to subpart R (section 215.445) of Ill. Adm. 
Code 215 (incorporated by reference as specified in 40 CFR 52.742) 
shall, for the purpose of detecting leaks, conduct a component 
monitoring program consistent with the following provisions:
    (A) Test once between March 1 and June 1 of each year, by methods 
referenced in paragraph (a)(4)(vii) of this section, all pump seals, 
pipeline valves in liquid service and process drains.
    (B) Test once each quarter of each calendar year, by methods 
referenced in paragraph (a)(4)(vii) of this section, all pressure relief 
valves in gaseous

[[Page 381]]

service, pipeline valves in gaseous service and compressor seals.
    (C) Inaccessible valves may be tested once each calendar year 
instead of once each quarter of each calendar year.
    (D) Observe visually all pump seals weekly.
    (E) Test immediately any pump seal from which liquids are observed 
dripping,
    (F) Test any relief valve within 24 hours after it has vented to the 
atmosphere, and
    (G) Test immediately after repair any component that was found 
leaking.
    (ii) Storage tank valves and pressure relief devices connected to an 
operating flare header or vapor recovery device are exempt from the 
monitoring requirements in paragraph (j)(1)(i) of this section.
    (iii) The Administrator may require more frequent monitoring than 
would otherwise be required by paragraph (j)(1)(i) of this section for 
components which are demonstrated to have a history of leaking.
    (2) Alternative program for leaks. The Administrator may approve an 
alternative program of monitoring, recordkeeping or reporting to that 
prescribed in paragraph (j)(1) of this section and subpart R (sections 
215.446, 215.448, and 215.449) of Ill. Adm. Code 215 (incorporated by 
reference as specified in 40 CFR 52.742), upon a demonstration by the 
owner or operator of a petroleum refinery that the alternative program 
will provide refinery and USEPA personnel with an equivalent ability to 
identify and repair leaking components. Any alternative program can only 
be allowed if approved by the Administrator as a SIP or FIP revision.
    (3) Compliance schedule for leaks. The owner or operator of a 
petroleum refinery shall adhere to the increments of progress contained 
in the following schedule:
    (i) Submit to the Administrator a monitoring program consistent with 
subpart R (section 215.446) of Ill. Adm. Code 215 (incorporated by 
reference as specified in 40 CFR 52.742) prior to September 1, 1990.
    (ii) Submit to the Administrator the first monitoring report 
pursuant to subpart R (section 215.449) of Ill. Adm. Code 215 
(incorporated by reference as specified in 40 CFR 52.742) prior to 
October 1, 1990.
    (k)-(l) [Reserved]
    (m) Pharmaceutical manufacturing--(1) Applicability. (i) The rules 
of paragraph (m) of this section, except for paragraphs (m)(4) through 
(m)(6) of this section, apply to all emission sources of VOM, including 
but not limited to reactors, distillation units, dryers, storage tanks 
for VOL, equipment for the transfer of VOL, filters, crystallizers, 
washers, laboratory hoods, pharmaceutical coating operations, mixing 
operations and centrifuges used in manufacturing, including packaging, 
of pharmaceuticals, and emitting more than 6.8 kg/day (15 lbs/day) and 
more than 2,268 kg/year (2.5 tons/year) of VOM. If an emission source 
emits less than 2,268 kg/year (2.5 tons/year) of VOM, the requirements 
of this paragraph still apply to the emission source if VOM emissions 
from the emission source exceed 45.4 kg/day (100 lbs/day).
    (ii) Notwithstanding paragraph (m)(1)(i) of this section, the air 
suspension coater/dryer, fluid bed dryers, tunnel dryers, and 
Accelacotas located in Libertyville Township, Lake County, Illinois 
shall be exempt from the rules of paragraph (m) of this section, except 
for paragraphs (m)(4) through (m)(6) of this section, if emissions of 
VOM not vented to air pollution control equipment do not exceed the 
following levels:
    (A) For the air suspension coater/dryer: 2,268 kg/year (2.5 tons/
year);
    (B) For each fluid bed dryer: 4,535 kg/year (5.0 tons/year);
    (C) For each tunnel dryer: 6,803 kg/year (7.5 tons/year); and
    (D) For each Accelacota: 6,803 kg/year (7.5 tons/year).
    (iii) Paragraphs (m)(4) through (m)(6) of this section apply to a 
plant having one or more emission sources that:
    (A) Are used to manufacture pharmaceuticals, and
    (B) Emit more than 6.8 kg/day (15 lbs/day) of VOM and more than 
2,268 kg/year (2.5 tons/year) of VOM, or, if less than 2,268 kg/year 
(2.5 tons/year), these paragraphs still apply if emissions from one or 
more sources exceed 45.4 kg/day (100 lbs/day).
    (iv) No owner or operator shall violate any condition in a permit 
when

[[Page 382]]

the condition results in exclusion of an emission source from paragraph 
(m) of this section.
    (v) Any pharmaceutical manufacturing source that becomes subject to 
the provisions of paragraph (m) of this section at any time shall remain 
subject to the provisions of paragraph (m) of this section at all times.
    (vi) Emissions subject to paragraph (m) of this section shall be 
controlled at all times consistent with the requirements set forth in 
paragraph (m) of this section.
    (vii) Control devices required pursuant to paragraph (m) of this 
section shall be operated at all times when the source it is controlling 
is operated.
    (viii) Determinations of daily and annual emissions for purposes of 
paragraph (m)(1) of this section shall be made using both data on the 
hourly emission rate (or the emissions per unit of throughput) and 
appropriate daily and annual data from records of emission source 
operation (or material throughput or material consumption data). In the 
absence of representative test data pursuant to paragraph (m)(8) of this 
section for the hourly emission rate (or the emissions per unit of 
throughput), such items shall be calculated using engineering 
calculations, including the methods described in appendix B of ``Control 
of Volatile Organic Emissions from Manufacturing of Synthesized 
Pharmaceutical Products'' (EPA-450/2-78-029). (This subparagraph shall 
not affect the Administrator's authority to require emission tests to be 
performed pursuant to paragraph (m)(8) of this section.)
    (2) Control of reactors, distillation units, crystallizers, 
centrifuges and vacuum dryers. (i) The owner or operator shall equip all 
reactors, distillation units, crystallizers, centrifuges and vacuum 
dryers that are used to manufacture pharmaceuticals with surface 
condensers or other air pollution control equipment listed in paragraph 
(m)(2)(i)(B) of this section.
    (A) If a surface condenser is used, it shall be operated such that 
the condenser outlet gas temperature does not exceed:

    (1) 248.2 K (-13  deg. F) when condensing VOM of vapor pressure 
greater than 40.0kPa (5.8 psi) at 294.3K (70  deg. F), or
    (2) 258.2 K (5  deg. F) when condensing VOM of vapor pressure 
greater than 20.0 kPa (2.9 psi) at 294.3 K (70  deg. F), or
    (3) 273.2 K (32  deg. F) when condensing VOM of vapor pressure 
greater than 10.0 kPa (1.5 psi) at 294.3 K (70  deg. F), or
    (4) 283.2 K (50  deg. F) when condensing VOM of vapor pressure 
greater than 7.0 kPa (1.0 psi) at 294.3 K (70  deg. F), or
    (5) 298.2 K (77  deg. F) when condensing VOM of vapor pressure 
greater than 3.45 kPa (0.5 psi) at 294.3 K (70  deg. F).

    (B) If a scrubber, carbon adsorption, thermal afterburner, catalytic 
afterburner, or other air pollution control equipment other than a 
surface condenser is used, such equipment shall provide a reduction in 
the emissions of VOM of 90 percent or more.
    (ii) The owner or operator shall enclose all centrifuges used to 
manufacture pharmaceuticals and that have an exposed VOL surface, where 
the VOM in the VOL has a vapor pressure of 3.45 kPa (0.5 psi) or more at 
294.3 K (70  deg. F), except as production, sampling, maintenance, or 
inspection procedures require operator access.
    (3) Control of air dryers, production equipment exhaust systems and 
filters. (i) The owner or operator of an air dryer or production 
equipment exhaust system used to manufacture pharmaceuticals shall 
control the emissions of VOM from such emission sources by air pollution 
control equipment which reduces by 90 percent or more the VOM that would 
otherwise be emitted into the atmosphere.
    (ii) The owner or operator shall enclose all rotary vacuum filters 
and other filters used to manufacture pharmaceuticals and that have an 
exposed VOL surface, where the VOM in the VOL has a vapor pressure of 
3.45 kPa (0.5 psi) or more at 294 K (70  deg. F), except as production, 
sampling, maintenance, or inspection procedures require operator access.
    (4) Material storage and transfer. The owner or operator of a 
pharmaceutical manufacturing plant shall:
    (i) Provide a vapor balance system that is at least 90 percent 
effective in reducing VOM emissions from truck or railcar deliveries to 
storage tanks with capacities equal to or greater than 7.57 
m3 (2,000 gal) that store VOL with vapor pressures greater 
than 28.0 kPa (4.1 psi) at 294.3 K (70  deg. F), and

[[Page 383]]

    (ii) Install, operate, and maintain pressure/vacuum conservation 
vents set at 0.2 kPa (0.03 psi) or greater on all storage tanks that 
store VOL with vapor pressures greater than 10 kPa (1.5 psi) at 294.3 K 
(70  deg. F).
    (5) In-process tanks. The owner or operator shall install covers on 
all in-process tanks used to manufacture pharmaceuticals and containing 
a VOL at any time. These covers must remain closed, except as 
production, sampling, maintenance or inspection procedures require 
operator access.
    (6) Leaks. The owner or operator of a pharmaceutical manufacturing 
plant shall repair any component from which a leak of VOL can be 
observed. The repair shall be completed as soon as practicable but no 
later than 15 days after the leak is found. If the leaking component 
cannot be repaired until the process unit is shut down, the leaking 
component must then be repaired before the unit is restarted.
    (7) Other emission sources. The owner or operator of a washer, 
laboratory hood, tablet coating operation, mixing operation or any other 
process emission source not subject to paragraphs (m)(2) through (m)(6) 
of this section, and used to manufacture pharmaceuticals shall control 
the emissions of VOM from such emission sources by:
    (i) Air pollution control equipment which reduces by 81 percent or 
more the VOM that would otherwise be emitted to the atmosphere, or
    (ii) A surface condenser which captures all the VOM which would 
otherwise be emitted to the atmosphere and which meets the requirements 
of paragraph (m)(2)(i) of this section.
    (8) Testing. (i) Upon request by the Administrator, the owner or 
operator of any VOM emission source subject to paragraph (m) or exempt 
from paragraph (m) of this section by virtue of the provisions of 
paragraph (m)(1) of this section shall, at his own expense, demonstrate 
compliance to the Administrator by the methods or procedures listed in 
paragraph (a)(vi)(A) of this section.
    (ii) A person planning to conduct a VOM emissions test to 
demonstrate compliance with paragraph (m) of this section shall notify 
the Administrator of that intent not less than 30 calendar days before 
the planned initiation of the test.
    (9) Monitoring and recordkeeping for air pollution control 
equipment--(i) Monitoring. (A) At a minimum, continuous monitors for the 
following parameters shall be installed on air pollution control 
equipment used to control sources subject to paragraph (m) of this 
section:
    (1) Destruction device combustion temperature.
    (2) Temperature rise across a catalytic afterburner bed.
    (3) VOM concentration on a carbon absorption unit to determine 
breakthrough.
    (4) Outlet gas temperature of a refrigerated condenser.
    (5) Temperature of a non-refrigerated condenser coolant supply 
system.
    (B) Each monitor shall be equipped with a recording device.
    (C) Each monitor shall be calibrated quarterly.
    (D) Each monitor shall operate at all times while the associated 
control equipment is operating.
    (ii) Recordkeeping. (A) The owner or operator of a pharmaceutical 
manufacturing facility shall maintain the following records:
    (1) Parameters listed in paragraph (m)(9)(i)(A) of this section 
shall be recorded.
    (2) For sources subject to paragraph (m)(2) of this section, the 
vapor pressure of VOM being controlled shall be recorded for every 
process.
    (B) For any leak subject to paragraph (m)(6) of this section which 
cannot be readily repaired within one hour after detection, the 
following records shall be kept:
    (1) The name of the leaking equipment,
    (2) The date and time the leak is detected,
    (3) The action taken to repair the leak, and
    (4) The data and time the leak is repaired.
    (C) The following records shall be kept for emission sources subject 
to paragraph (m)(5) of this section which contain VOL:
    (1) For maintenance and inspection:
    (i) The date and time each cover is opened,

[[Page 384]]

    (ii) The length of time the cover remains open, and
    (iii) The reason why the cover is opened.
    (2) For production and sampling, detailed written procedures or 
manufacturing directions specifying the circumstances under which covers 
may be opened and the procedures for opening covers.
    (D) For each emission source used in the manufacture of 
pharmaceuticals for which the owner or operator of a pharmaceutical 
manufacturing plant claims emission standards are not applicable, 
because the emissions are below the applicability cutoffs in paragraph 
(m)(1)(i) of this section or paragraph (m)(1)(ii) of this section the 
owner or operator shall:
    (1) Maintain a demonstration including detailed engineering 
calculations of the maximum daily and annual emissions for each such 
emission source showing that the emissions are below the applicability 
cutoffs in paragraph (m)(1)(i) or paragraph (m)(1)(ii) of this section, 
as appropriate, for the current and prior calendar years;
    (2) Maintain appropriate operating records for each such emission 
source to identify whether the applicability cutoffs in paragraph 
(m)(1)(i) or paragraph (m)(1)(ii) of this section, as appropriate, are 
ever exceeded; and
    (3) Provide written notification to the Administrator within 30 days 
of a determination that such an emission source has exceeded the 
applicability cutoffs in paragraph (m)(1)(i) or paragraph (m)(1)(ii) of 
this section, as appropriate.
    (E) Records required under paragraph (m)(9)(ii)(A) of this section 
shall be maintained by the owner or operator for a minimum of two years 
after the date on which they are made.
    (F) Copies of the records shall be made available to the 
Administrator upon verbal or written request.
    (n)--(p) [Reserved]
    (q) Gasoline distribution--(1) Bulk gasoline plants. (i) Subject to 
paragraph (q)(1)(v) of this section, no person may cause or allow the 
transfer of gasoline from a delivery vessel into a stationary storage 
tank located at a bulk gasoline unless:
    (A) The delivery vessel and the stationary storage tank are each 
equipped with a vapor collection system that meets the requirements of 
paragraph (q)(1)(iv)(D) of this section,
    (B) Each vapor collection system is operating,
    (C) The delivery vessel displays the appropriate sticker pursuant to 
the requirements of sections 215.584 (b) or (d) of 35 I11. Adm. Code 215 
(incorporated by reference as specified in 40 CFR 52.742),
    (D) The pressure relief valve(s) on the stationary storage tank and 
the delivery vessel are set to release at no less than 0.7 psi or the 
highest pressure allowed by state or local fire codes or the guidelines 
of the National Fire Prevention Association, and
    (E) The stationary storage tank is equipped with a submerged loading 
pipe.
    (ii) Subject to paragraph (q)(1)(vi) of this section, no person may 
cause or allow the transfer of gasoline from a stationary storage tank 
located at a bulk gasoline plant into a delivery vessel unless:
    (A) The requirements set forth in paragraphs (q) (1)(i)(A) through 
(1)(i)(D) of this section are met, and
    (B) Equipment is available at the bulk gasoline plant to provide for 
the submerged filling of the delivery vessel or the delivery vessel is 
equipped for bottom loading.
    (iii) Subject to paragraph (q)(1)(v) of this section, each owner of 
a stationary storage tank located at a bulk gasoline plant shall:
    (A) Equip each stationary storage tank with a vapor control system 
that meets the requirements of paragraph (q) (1)(i) or (1)(ii) of this 
section, whichever is applicable,
    (B) Provide instructions to the operator of the bulk gasoline plant 
describing necessary maintenance operations and procedures for prompt 
notification of the owner in case of any malfunction of a vapor control 
system, or
    (C) Repair, replace or modify any worn out or malfunctioning 
component or element of design.
    (iv) Subject to paragraph (q)(1)(v) of this section, each operator 
of a bulk gasoline plant shall:

[[Page 385]]

    (A) Maintain and operate each vapor control system in accordance 
with the owner's instructions,
    (B) Promptly notify the owner of any scheduled maintenance or 
malfunction requiring replacement or repair of a major component of a 
vapor control system,
    (C) Maintain gauges, meters or other specified testing devices in 
proper working order, and
    (D) Operate the bulk plant vapor collection system and gasoline 
loading equipment in a manner that prevents:
    (1) Gauge pressure from exceeding 45.7 cm (18 in.) of water and 
vacuum from exceeding 15.2 cm (6 in.) of water, as measured as close as 
possible to the vapor hose connection,
    (2) A reading equal to or greater than 100 percent of the lower 
explosive limit (LEL measured as propane) when tested in accordance with 
the procedure described in ``Control of Volatile Organic Compound Leaks 
from Gasoline Tank Trucks and Vapor Collection Systems'', Appendix B, 
EPA 450/2-78-051 (which is available for purchase from the National 
Technical Information Services, 5285 Port Royal Road, Springfield, VA 
22161), and
    (3) Avoidable leaks of liquid during loading or unloading 
operations.
    (E) Provide a pressure tap or equivalent on the bulk plant vapor 
collection system in order to allow the determination of compliance with 
paragraph (q)(1)(iv)(D)(1) of this section, and
    (F) Within 15 business days after discovery of any leak by the 
owner, operator, or the Administrator, repair and retest a vapor 
collection system which exceeds the limits of paragraph (q)(1)(iv)(D) 
(1) or (2) of this section.
    (v) The requirements of paragraphs (q) (1)(i), (1)(iii) and (1)(iv) 
of this section, shall not apply to:
    (A) Any stationary storage tank with a capacity of less than 2,177 l 
(575 gal), or
    (B) Any bulk gasoline plant whose daily gasoline throughtput is less 
than 15,140 l (4,000 gal/day) on a thirty-day rolling average.
    (vi) The requirements of paragraph (q)(1)(ii) of this section shall 
only apply to bulk gasoline plants:
    (A) Whose daily gasoline throughput is greater than or equal to 
15,140 l (4,000 gal/day) on a thirty-day rolling average, and
    (B) That either distribute gasoline to gasoline dispensing 
facilities subject to the requirements of section 215.583(a)(2) of 35 
Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 
52.742) or that are in Cook, DuPage, Kane, Lake, McHenry or Will County.
    (vii) Any bulk gasoline plant which is ever subject to paragraph 
(q)(1) (i), (ii), (iii) or (iv) of this section shall always be subject 
to these paragraphs.
    (2) [Reserved]
    (r) [Reserved]
    (s) Paint and ink manufacturing--(1) Applicability. (i) Paragraph 
(s) shall apply to all paint and ink manufacturing plants which:
    (A) Include process emission sources not subject to subparts (B), 
(Q) (excluding sections 215.432 and 215.436), (R) (excluding sections 
215.447, 215.450, and 215.452), (S), (V), (X), (Y) (sections 215.582, 
215.583, and 215.584), or (Z) of 35 Ill. Adm. Code 215 (incorporated by 
reference as specified in 40 CFR 52.742), or to paragraphs (d), (e) 
(excluding paragraph (e)(1)(i)(L)), (h) (excluding paragraph (h)(5)), 
(i), (j), or (q)(1) of this section; and which as a group both:
    (1) Have maximum theoretical emissions of 91 Mg (100 tons) or more 
per calendar year of VOM if no air pollution control equipment were 
used, and
    (2) Are not limited to less than 91 Mg (100 tons) of VOM emissions 
per calendar year in the absence of air pollution control equipment, 
through production or capacity limitations contained in a federally 
enforceable construction permit or a SIP or FIP revision, or
    (B) Produce more than 7,570,820 l (2,000,000 gal) per calendar year 
of paint or ink formulations, which contain less than 10 percent (by 
weight) water, and ink formulations not containing as the primary 
solvents water, Magie oil or glycol.
    (ii) For the purposes of paragraph (s) of this section, uncontrolled 
VOM emissions are the emissions of VOM which would result if no air 
pollution control equipment were used.
    (2) Exemption for waterbase material and heatset-offset ink. The 
requirements of paragraphs (s)(4) and (s)(5) of this section and 
paragraph (s)(7)(i) of this

[[Page 386]]

section shall not apply to equipment while it is being used to produce 
either:
    (i) Paint or ink formulations which contain 10 percent or more (by 
weight) water, or
    (ii) Inks containing Magie oil and glycol as the primary solvent.
    (3) Permit conditions. No person shall violate any condition in a 
federally enforceable permit when the condition results in exclusion of 
the plant or an emission source from paragraph (s).
    (4) Open-top mills, tanks, vats or vessels. No person shall operate 
an open-top mill, tank, vat or vessel with a volume of more than 45 l 
(12 gal) for the production of paint or ink unless:
    (i) The mill, tank, vat or vessel is equipped with a cover which 
completely covers the mill, tank, vat or vessel opening except for an 
opening no larger than necessary to allow for safe clearance for a mixer 
shaft. Such cover shall extend at least 1.27 cm (0.5 in.) beyond the 
outer rim of the opening or be attached to the rim.
    (ii) The cover remains closed except when production, sampling, 
maintenance or inspection procedures require access.
    (iii) The cover is maintained in good condition such that, when in 
place, it maintains contact with the rim of the opening for at least 90 
percent of the circumference of the rim.
    (5) Grinding mills. (i) No person shall operate a grinding mill for 
the production of paint or ink which is not maintained in accordance 
with the manufacturer's specifications.
    (ii) No person shall operate a grinding mill fabricated or modified 
after the effective date of paragraph (s) which is not equipped with 
fully enclosed screens.
    (iii) The manufacturer's specifications shall be kept on file at the 
plant by the owner or operator of the grinding mill and be made 
available to any person upon verbal or written request during business 
hours.
    (6) Storage tanks. (i) The owner or operator shall equip tanks 
storing VOL with a vapor pressure greater than 10 kPa (1.5 psi) at 20 
deg.C (68  deg.F) with pressure/vacuum conservation vents set as a 
minimum at +/-0.2 kPa (0.029 psi). These controls shall be operated at 
all times. An alternative air pollution control system may be used if it 
results in a greater emission reduction than these controls. Any 
alternative control system can only be allowed if approved by the 
Administrator as a SIP or FIP revision.
    (ii) Stationary VOL storage containers with a capacity greater than 
946 l (250 gal) shall be equipped with a submerged-fill pipe or bottom 
fill. These controls shall be operated at all times. An alternative 
control system can only be allowed if approved by the Administrator as a 
SIP or FIP revision.
    (7) Leaks. The owner or operator of a paint or ink manufacturing 
plant shall, for the purpose of detecting leaks, conduct an equipment 
monitoring program as set forth below:
    (i) Each pump shall be checked by visual inspection each calendar 
week for indications of leaks, that is, liquids dripping from the pump 
seal. If there are indications of liquids dripping from the pump seal, 
the pump shall be repaired as soon as practicable, but no later than 15 
calendar days after the leak is detected.
    (ii) Any pump, valve, pressure relief valve, sampling connection, 
open-ended valve and flange or connector containing a fluid which is at 
least 10 percent VOM by weight which appears to be leaking on the basis 
of sight, smell or sound shall be repaired as soon as practicable, but 
no later than 15 calendar days after the leak is detected.
    (iii) A weather proof, readily visible tag, in bright colors such as 
red or yellow, bearing an identification number and the date on which 
the leak was detected shall be attached to leaking equipment. The tag 
may be removed upon repair, that is, when the equipment is adjusted or 
otherwise altered to allow operation without leaking.
    (iv) When a leak is detected, the owner or operator shall record the 
date of detection and repair and the record shall be retained at the 
plant for at least two years from the date of each detection or each 
repair attempt. The record shall be made available to any person upon 
verbal or written request during business hours.
    (8) Clean up. (i) No person shall clean paint or ink manufacturing 
equipment

[[Page 387]]

with organic solvent unless the equipment being cleaned is completely 
covered or enclosed except for an opening no larger than necessary to 
allow safe clearance for proper operation of the cleaning equipment, 
considering the method and materials being used.
    (ii) No person shall store organic wash solvent in other than closed 
containers, unless closed containers are demonstrated to be a safety 
hazard, or dispose of organic wash solvent in a manner such that more 
than 20 percent by weight is allowed to evaporate into the atmosphere.
    (9) Compliance schedule. Every owner or operator of an emission 
source subject to the control requirements of paragraph (s) of this 
section shall comply with the requirements of paragraph (s) of this 
section on and after July 1, 1991.
    (10) Recordkeeping and reporting. (i) Upon request by the 
Administrator, the owner or operator of an emission source which claims 
to be exempt from the requirements of paragraph (s) of this section 
shall submit records to the Administrator within 30 calendar days from 
the date of the request which document that the emission source is in 
fact exempt from paragraph (s) of this section. These records shall 
include (but are not limited to) the percent water (by weight) in the 
paint or ink being produced and the quantity of Magie oil, glycol and 
other solvents in the ink being produced.
    (ii) Every owner or operator of an emission source which is subject 
to the requirements of paragraph (s) of this section shall maintain all 
records necessary to demonstrate compliance with those requirements at 
the facility for three years.
    (t) [Reserved]
    (u) Miscellaneous fabricated product manufacturing processes--(1) 
Applicability.
    (i) The requirements of paragraph (u) of this section shall apply to 
a plant's miscellaneous fabricated product manufacturing process 
emission sources which are not included within any of the source 
categories specified in subparts (B), (Q) (excluding sections 215.432 
and 215.436), (R) (excluding sections 215.447, 215.450, and 215.452), 
(S), (V), (X), (Y) (sections 215.582, 215.583, and 215.584), or (Z) of 
35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 
52.742), or specified in paragraph (d), (e), (h), (i), (j), or (q)(1) of 
this section; if the plant is subject to paragraph (u) of this section. 
A plant is subject to paragraph (u) of this section if it contains 
process emission sources, not regulated by subparts (B), (Q) (excluding 
sections 215.432 and 215.436), (R) (excluding sections 215.447, 215.450, 
and 215.452), (S), (V), (X), (Y) (sections 215.582, 215.583, 215.584), 
or (Z) of 35 Ill. Adm. Code 215 (incorporated by reference as specified 
in 40 CFR 52.742), or by paragraph (d), (e) (excluding paragraph 
(e)(1)(i)(L)), (h) (excluding paragraph (h)(5)), (i), (j), or (q)(1) of 
this section; which as a group both:
    (A) Have maximum theoretical emissions of 91 Mg (100 tons) or more 
per calendar year of VOM if no air pollution control equipment were 
used, and
    (B) Are not limited to less than 91 Mg (100 tons) of VOM emissions 
per calendar year in the absence of air pollution control equipment, 
through production or capacity limitations contained in a federally 
enforceable construction permit or a SIP or FIP revision.
    (ii) If a plant ceases to fulfill the criteria of paragraph 
(u)(1)(i) of this section, the requirements of paragraph (u) of this 
section shall continue to apply to a miscellaneous fabricated products 
manufacturing process emission source which was ever subject to the 
control requirements of paragraph (u)(3) of this section.
    (iii) No limits under paragraph (u) of this section shall apply to 
emission sources with emissions of VOM to the atmosphere less than or 
equal to 0.91 Mg (1.0 ton) per calendar year if the total emissions from 
such sources not complying with paragraph (u)(3) of this section does 
not exceed 4.5 Mg (5.0 tons) per calendar year.
    (iv) For the purposes of paragraph (u) of this section, an emission 
source shall be considered regulated by a subpart (of the Illinois 
rules) or paragraph if it is subject to the limits of that subpart (of 
the Illinois rules) or paragraph. An emission source is not considered 
regulated by a subpart (of the Illinois rules) or paragraph if its 
emissions are below the applicability cutoff level or

[[Page 388]]

if the source is covered by an exemption.
    (v) For the purposes of paragraph (u) of this section, uncontrolled 
VOM emissions are the emissions of VOM which would result if no air 
pollution control equipment were used.
    (2) Permit conditions. No person shall violate any condition in a 
permit when the condition results in exclusion of the plant or an 
emission source from paragraph (u) of this section.
    (3) Control requirements. Every owner or operator of an emission 
source subject to paragraph (u) of this section shall comply with the 
requirements of paragraph (u)(3) (i), (ii) or (iii) of this section:
    (i) Emission capture and control techniques which achieve an overall 
reduction in uncontrolled VOM emissions of at least 81 percent, or
    (ii) For coating lines, the daily-weighted average VOM content shall 
not exceed 0.42 kg VOM/l (3.5 lbs VOM/gal) of coating as applied (minus 
water and any compounds which are specifically exempted from the 
definition of VOM) during any day. Owners and Code 215 (incorporated by 
reference as specified in 40 CFR 52.742), or
    (iii) An alternative control plan which has been approved by the 
Administrator as a SIP or FIP revision.
    (4) Compliance schedule. Every owner or operator of an emission 
source subject to the control requirements of paragraph (u) of this 
section shall comply with the requirements of paragraph (u) of this 
section on and after July 1, 1991.
    (5) Testing. Any owner or operator of a VOM emission source which is 
subject to paragraph (u) of this section shall demonstrate compliance 
with paragraph (u)(3) of this section by using the applicable test 
methods and procedures specified in paragraph (a)(4) of this section.
    (6) The control requirements in this paragraph apply to the adhesive 
globe coating operations at Replogle's Broadview facility in Cook 
County, Illinois, instead of the control requirements in paragraph 
(u)(3) of this section.
    (i) After October 6, 1991, no coatings shall at any time be applied 
which exceed the following emission limitations for the specified 
coating.
    (A) 7.0 lbs VOM per gallon of adhesive coating (minus water and any 
compounds which are specifically exempted from the definition of VOM) as 
applied to coat globes. Such coating consists of #7879446 Methylene 
Chloride (RGI #01004100). The Administrator shall be notified at least 
ten (10) days prior to the use of any replacement adhesive for coating 
globes.
    (B) [Reserved]
    (ii) After October 6, 1991, the volume of coatings used shall not 
exceed the following:
    (A) 572 gallons per year total for all coatings specified in 
paragraph (u)(6)(i)(A) of this section. The yearly volume of coatings 
used are to be calculated as follows:
    (1) Compute the volume of specified coating used each month by the 
15th of the following month.
    (2) By the 15th of each month, add the monthly coating use for the 
12 previous months (to obtain the yearly volume of coatings used).
    (B) [Reserved]
    (iii) Beginning on October 6, 1991, the owner and operator of the 
Replogle Globes, Inc. plant in Broadview, Illinois shall keep the 
following records for each month. All records shall be retained at 
Replogle Globes, Inc. for three (3) years and shall be made available to 
the Administrator on request:
    (A) The name and identification number of each coating as applied on 
any adhesive globe coating line.
    (B) The weight of VOM per volume and the volume of each coating 
(minus water and any compounds which are specifically exempted from the 
definition of VOM) as applied each month on any adhesive globe coating 
line.
    (7) The control requirements in this paragraph apply to the glass 
candle container coating line(s) and silk screening machines at the 
Candle Corporation of America (CCA), Chicago, Illinois facility, instead 
of the control requirements in paragraph (u)(3) of this section.
    (i) After June 1, 1992, no coatings or inks shall at any time be 
applied, at any coating or ink applicator, which exceed the following 
emission limitations for the specified coating or ink.

[[Page 389]]

    (A) 6.04 pounds (lbs) volatile organic material (VOM) per gallon of 
clear lacquer/varnish (minus water and any compounds which are 
specifically exempted from the definition of VOM) as applied to coat 
glass candle containers. Such clear lacquer/varnish (multi-color) is 
identified as LP3500. The Administrator must be notified at least 10 
days prior to the use of any replacement clear lacquers/varnishes.
    (B) 5.23 lbs VOM per gallon of translucent coating (minus water and 
any compounds which are specifically exempted from the definition of 
VOM) as applied to coat glass candle containers. Such translucent 
coating (multi-color) is identified as LP3603. The Administrator must be 
notified at least 10 days prior to the use of any replacement 
translucent coatings.
    (C) 5.84 lbs VOM per gallon of white lacquer (minus water and any 
compounds which are specifically exempted from the definition of VOM) as 
applied to coat glass candle containers. Such white lacquer is 
identified as LP3507. The Administrator must be notified at least 10 
days prior to the use of any replacement white lacquers.
    (D) 3.40 lbs VOM per gallon of fast dry enamel silk screen printing 
ink (minus water and any compounds which are specifically exempted from 
the definition of VOM) as applied to print onto glass candle containers.
    (ii) After June 1, 1992, the volume of coating and ink used shall 
not exceed the following:
    (A) 2,164 gallons per month total for all coatings specified in 
paragraph (u)(7)(i)(A) of this section.
    (B) 369 gallons per month total for all coatings specified in 
paragraph (u)(7)(i)(B) of this section.
    (C) 49 gallons per month total for all coatings specified in 
paragraph (u)(7)(i)(C) of this section.
    (D) 50 gallons per month total for all inks specified in paragraph 
(u)(7)(i)(D) of this Section.
    (iii) Beginning on June 1, 1992, the owner and operator of CCA's 
plant in Chicago, Illinois, shall keep the following records for each 
month. All records shall be retained at CCA for 3 years and shall be 
made available to the Administrator on request.
    (A) The name and identification number of each coating and ink as 
applied on any glass candle container coating line or silk screening 
machine.
    (B) The weight of VOM per volume and the volume of each coating and 
ink (minus water and any compounds which are specifically exempted from 
the definition of VOM) as applied each month on any glass candle 
container coating line or silk screening machine.
    (iv) After June 1, 1992, no more than 100 gallons per month of 
cleaning solvent is allowed to be used on the glass candle container 
coating line(s) at CCA. The only cleaning solvents allowed for use are 
acetone (identified as LP3525) and methyl ethyl ketone (identified as 
LP3520). Beginning on June 1, 1992, CCA shall keep monthly records of 
the type and volume of all cleaning solvents used. All such records 
shall be retained at CCA for 3 years and shall be made available to the 
Administrator on request.
    (v) After June 1, 1992, no more than 50 gallons per month of 
cleaning solvent is allowed to be used on the glass candle container 
silk screening machines at CCA. The only cleaning solvent allowed for 
use is petroleum naphtha (identified as light aromatic naphtha with 7.28 
lbs VOM per gallon, minus water and any compounds which are specifically 
exempted from the definition of VOM). Beginning on June 1, 1992, CCA 
shall keep monthly records of the type and volume and the weight of VOM 
per volume (minus water and any compounds which are specifically 
exempted from the definition of VOM) of all cleaning solvents used on 
the glass candle container silk screening machines. All such records 
shall be retained at CCA for 3 years and shall be made available to the 
Administrator on request.
    (8) The control, recordkeeping and reporting requirements in this 
paragraph apply to the cellulose food casing manufacturing operations at 
the Viskase Corporation plant in Bedford Park, Illinois (Cook County) 
instead of the requirements in paragraph (v) of this section, the other 
parts of paragraph (u) of

[[Page 390]]

this section, and the recordkeeping requirements in paragraph (y) of 
this section. Unless otherwise stated, the following requirements must 
be met by Viskase on and after November 21, 1995.
    (i) VOM emissions shall never exceed 3.30 tons per day.
    (ii) VOM emissions shall not exceed 2.22 tons per day, on a monthly 
average, during June, July, and August.
    (iii) VOM emissions shall not exceed 2.44 tons per day during June, 
July, and August.
    (iv) Compliance with the emission limits in paragraphs (u)(8) (i) 
through (iii) of this section, and the records in paragraph (u)(8)(v) of 
this section, shall be determined using an emission factor of ``0.72 
pounds of VOM emissions per pound of carbon disulfide consumed.''
    (v) Viskase must keep the following daily records:
    (A) The pounds of carbon disulfide per charge for its Fibrous 
process. If charges with different levels of carbon disulfide per charge 
are used the same day, a separate record must be kept for each level of 
carbon disulfide per charge.
    (B) The pounds of carbon disulfide per charge for its NOJAX process. 
If charges with different levels of carbon disulfide per charge are used 
the same day, a separate record must be kept for each level of carbon 
disulfide per charge.
    (C) The number of charges per day, for each level of carbon 
disulfide per charge, used in Viskase's Fibrous process.
    (D) The number of charges per day, for each level of carbon 
disulfide per charge, used in Viskase's NOJAX process.
    (E) The total quantity of carbon disulfide used per day in Viskase's 
Fibrous process, the total quantity of carbon disulfide used per day in 
Viskase's NOJAX process, and the daily VOM emissions resulting from use 
of the carbon disulfide.
    (F) The monthly use of carbon disulfide, and the monthly VOM 
emissions resulting from use of the carbon disulfide, during June, July, 
and August.
    (vi) Any violation of the emission limits in paragraphs (u)(8) (i) 
through (iii) of this section must be reported to USEPA within 30 days 
of its occurrence.
    (vii) In order to determine daily and monthly VOM emissions, the 
test methods in paragraph (a)(4) of this section may be used in addition 
to, and take precedence over, the emission factor cited in paragraph 
(u)(8)(iv) of this section. Method 15 is to be used instead of Methods 
18, 25, and 25A when the test methods in paragraph (a)(4) of this 
section are used to determine VOM emissions from Viskase's cellulose 
food casing facility.
    (v) Miscellaneous formulation manufacturing processes--(1) 
Applicability. (i) The requirements of paragraph (v) of this section 
shall apply to a plant's miscellaneous formulation manufacturing process 
emission sources, which are not included within any of the source 
categories specified in subpart (B), (Q) (excluding sections 215.432 and 
215.436), (R) (excluding sections 215.447, 215.450, and 215.452),(S), 
(V), (X), (Y) (sections 215.582, 215.583, and 215.584), or (Z) of 35 
Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 
52.742), or specified in paragraph (d), (e), (h), (i), (j), or (q)(1) of 
this section; if the plant is subject to paragraph (v) of this section. 
A plant is subject to paragraph (v) of this section if it contains 
process emission sources, not regulated by subpart (B), (Q) (excluding 
sections 215.432 and 215.436), (R) (excluding sections 215.447, 215.450, 
and 215.452), (S), (V), (X), (Y) (sections 215.582, 215.583, and 
215.584), or (Z) of 35 Ill. Adm. Code 215 (incorporated by reference as 
specified in 40 CFR 52.742), or by paragraph (d), (e) (excluding 
paragraph (e)(1)(i)(L)), (h) (excluding paragraph (h)(5)), (i), (j), or 
(q)(1) of this section; which as a group both:
    (A) Have maximum theoretical emissions of 91 Mg (100 tons) or more 
per calendar year of VOM if no air pollution control equipment were 
used, and
    (B) Are not limited to less than 91 Mg (100 tons) of VOM emissions 
per calendar year in the absence of air pollution control equipment, 
through production or capacity limitations contained in a federally 
enforceable construction permit or a SIP or FIP revision.

[[Page 391]]

    (ii) If a plant ceases to fulfill the criteria of paragraph 
(v)(1)(i) of this section, the requirements of paragraph (v) of this 
section shall continue to apply to a miscellaneous formulation 
manufacturing process emission source which was ever subject to the 
control requirements of paragraph (v)(3) of this section.
    (iii) No limits under paragraph (v) of this section shall apply to 
emission sources with emissions of VOM to the atmosphere less than or 
equal to 2.3 Mg (2.5 tons) per calendar year if the total emissions from 
such sources not complying with paragraph (v)(3) of this section does 
not exceed 4.5 Mg (5.0 tons) per calendar year.
    (iv) For the purposes of paragraph (v) of this section, an emission 
source shall be considered regulated by a subpart (of the Illinois 
rules) or paragraph if it is subject to the limits of that subpart (of 
the Illinois rules) or paragraph. An emission source is not considered 
regulated by a subpart (of the Illinois rules) or paragraph if its 
emissions are below the applicability cutoff level or if the source is 
covered by an exemption.
    (v) For the purposes of paragraph (v) of this section uncontrolled 
VOM emissions are the emissions of VOM which would result if no air 
pollution control equipment were used.
    (2) Permit conditions. No person shall violate any condition in a 
permit when the condition results in exclusion of the plant or an 
emission source from paragraph (v) of this section.
    (3) Control requirements. Every owner or operator of an emission 
source subject to paragraph (v) of this section shall comply with the 
requirements of paragraph (v)(3) (i) or (ii) of this section.
    (i) Emission capture and control techniques which achieve an overall 
reduction in uncontrolled VOM emissions of at least 81 percent, or
    (ii) An alternative control plan which has been approved by the 
Administrator as a SIP or FIP revision.
    (4) Compliance schedule. Every owner or operator of an emission 
source subject to the control requirements of paragraph (v) of this 
section shall comply with the requirements of paragraph (v) of this 
section on and after July 1, 1991.
    (5) Testing. Any owner or operator of a VOM emission source which is 
subject to paragraph (v) of this section shall demonstrate compliance 
with paragraph (v)(3) of this section by using the applicable test 
methods and procedures specified in paragraph (a)(4) of this section.
    (6) The control requirements in this paragraph apply to the 7 
blenders and 3 moguls of the adhesive coating solution formulation 
(compounding) operations at the Minnesota Mining and Manufacturing 
Corporation's (3M) Bedford Park facility in Cook County, Illinois, 
instead of the control requirements in paragraph (v)(3) of this section.
    (i) After September 1, 1991, the following operating restrictions 
shall apply to 3M's Bedford Park, Illinois, compounding operations.
    (A) The combined operating hours for all blenders shall not exceed 
8,400 hours per quarter (rolled on a monthly basis). The combined 
quarterly operating hours of all blenders are to be calculated as 
follows:
    (1) By the 15th of each month, compute the combined monthly 
operating hours of all blenders during the previous month.
    (2) By the 15th of each month, add the monthly operating hours of 
all blenders for the 3 previous months (to obtain the combined quarterly 
operating hours of all blenders).
    (B) The combined operating hours for all moguls shall not exceed 
4,200 hours per quarter (rolled on a monthly basis). The quarterly 
operating hours of all moguls are to be calculated as follows:
    (1) By the 15th of each month, compute the combined monthly 
operating hours of all moguls during the previous month.
    (2) By the 15th of each month, add the monthly operating hours of 
all moguls for the 3 previous months (to obtain the combined quarterly 
operating hours of all moguls).
    (ii) Beginning on September 1, 1991, the owner and operator of the 
3M Bedford Park Plant in Bedford Park, Illinois, shall keep the 
following records. These records shall be compiled on a monthly basis, 
be retained at the 3M

[[Page 392]]

facility for a period of 3 years, and be made available to the 
Administrator upon request.
    (A) Separate monthly records for each of the 7 blenders identifying 
each batch and the length of each batch as well as the total monthly 
hours of operation for all blenders.
    (B) Separate monthly records for each of the 3 moguls identifying 
each batch and the length of each batch as well as the total monthly 
hours of operation for all moguls.
    (w) Miscellaneous organic chemical manufacturing processes--(1) 
Applicability. (i) The requirements of paragraph (w) of this section 
shall apply to a plant's miscellaneous organic chemical manufacturing 
process emission sources which are not included within any of the source 
categories specified in subparts (B), (Q) (excluding sections 215.432 
and 215.436), (R) (excluding sections 215.447, 215.450, and 215.452), 
(S), (V), (X), (Y) (sections 215.582, 215.583, and 215.584), or (Z) of 
35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 
52.742), or specified in paragraph (d), (e), (h), (i), (j), or (q)(1) of 
this section; if the plant is subject to paragraph (w) of this section. 
A plant is subject to paragraph (w) of this section if it contains 
process emission sources, not regulated by subparts (B), (Q) (excluding 
sections 215.432 and 215.436), (R) (excluding sections 215.447, 215.450, 
and 215.452), (S), (V), (X), (Y) (sections 215.582, 215.583, and 
215.584), or (Z) of 35 Ill. Adm. Code 215 (incorporated by reference as 
specified in 40 CFR 52.742), or by paragraph (d), (e) (excluding 
paragraph (e)(1)(i)(L)), (h) (excluding paragraph (h)(5)), (i), (j), or 
(q)(1) of this section; which as a group both:
    (A) Have maximum theoretical emissions of 91 Mg (100 tons) or more 
per calendar year of VOM if no air pollution control equipment were 
used, and
    (B) Are not limited to less than 91 Mg (100 tons) of VOM emissions 
per calendar year in the absence of air pollution control equipment, 
through production or capacity limitations contained in a federally 
enforceable construction permit or a SIP or FIP revision.
    (ii) If a plant ceases to fulfill the criteria of paragraph 
(w)(1)(i) of this section, the requirements of paragraph (w) of this 
section shall continue to apply to a miscellaneous organic chemical 
manufacturing process emission source which was ever subject to the 
control requirements of paragraph (w)(3) of this section.
    (iii) No limits under paragraph (w) of this section shall apply to 
emission sources with emissions of VOM to the atmosphere less than or 
equal to 0.91 Mg (1.0 ton) per calendar year if the total emissions from 
such sources not complying with paragraph (w)(3) of this section does 
not exceed 4.5 Mg (5.0 tons) per calendar year.
    (iv) For the purposes of paragraph (w) of this section, an emission 
source shall be considered regulated by a subpart (of the Illinois 
rules) or paragraph if it is subject to the limits of that subpart (of 
the Illinois rules) or paragraph. An emission source is not considered 
regulated by a subpart (of the Illinois rules) or paragraph if its 
emissions are below the applicability cutoff level or if the source is 
covered by an exemption.
    (v) For the purposes of paragraph (w) of this section, uncontrolled 
VOM emissions are the emissions of VOM which would result if no air 
pollution control equipment were used.
    (2) Permit conditions. No person shall violate any condition in a 
permit when the condition results in exclusions of the plant or an 
emission source from paragraph (w) of this section.
    (3) Control requirements. Every owner or operator of an emission 
source subject to paragraph (w) of this section shall comply with the 
requirements of paragraph (w)(3)(i) or (ii) of this section.
    (i) Emission capture and control techniques which achieve an overall 
reduction in uncontrolled VOM emissions of at least 81 percent, or
    (ii) An alternative control plan which has been approved by the 
Administrator as a SIP or FIP revision.
    (4) Compliance schedule. Every owner or operator of an emission 
source subject to the control requirements of paragraph (w) of this 
section shall comply with the requirements of paragraph (w) of this 
section on and after July 1, 1991.

[[Page 393]]

    (5) Testing. Any owner or operator of a VOM emission source which is 
subject to paragraph (w) shall demonstrate compliance with paragraph 
(w)(3) of this section by using the applicable test methods and 
procedures specified in paragraph (a)(4) of this section.
    (x) Other emission sources--(1) Applicability. (i) The requirements 
of paragraph (x) of this section shall apply to a plant's VOM emission 
sources, which are not included within any of the source categories 
specified in subpart (B), (Q) (excluding sections 215.432 and 215.436), 
(R) (excluding sections 215.447, 215.450, and 215.452), (S), (V), (X), 
(Y) (sections 215.582, 215.583, and 215.584), or (Z) of 35 Ill. Adm. 
Code 215 (incorporated by reference as specified in 40 CFR 52.742), or 
specified in paragraph (d), (e), (h), (i), (j), (q)(1), (s), (u), (v) or 
(w) of this section; if the plant is subject to paragraph (x) of this 
section. A plant is subject to paragraph (x) of this section if it 
contains process emission sources, not regulated by subpart (B), (Q) 
(excluding sections 215.432 and 215.436), (R) (excluding sections 
215.447, 215.450, and 215.452), (S), (V), (X), (Y) (sections 215.582, 
215.583, and 215.584), or (Z) of 35 Ill. Adm. Code 215 (incorporated by 
reference as specified in 40 CFR 52.742), or by paragraph (d), (e) of 
this section (excluding paragraph (e)(1)(i)(L)), (h) (excluding 
paragraph (h)(5)), (i), (j), or (q)(1) of this section; which as a group 
both:
    (A) Have maximum theoretical emissions of 91 Mg (100 tons) or more 
per calendar year of VOM if no air pollution control equipment were 
used, and
    (B) Are not limited to less than 91 Mg (100 tons) of VOM emissions 
per calendar year in the absence of air pollution control equipment, 
through production or capacity limitations contained in a federally 
enforceable construction permit or a SIP of FIP revision.
    (ii) If a plant ceases to fulfill the criteria of paragraph 
(x)(1)(i) of this section, the requirements of paragraph (x) of this 
section shall continue to apply to an emission source which was ever 
subject to the control requirements of paragraph (x)(3) of this section.
    (iii) No limits under paragraph (x) of this section shall apply to 
emission sources with emissions of VOM to the atmosphere less than or 
equal to 2.3 Mg (2.5 tons) per calendar year if the total emissions from 
such sources not complying with paragraph (x)(3) of this section does 
not exceed 4.5 Mg (5.0 tons) per calendar year.
    (iv) For the purposes of paragraph (x) of this section, an emission 
source shall be considered regulated by a subpart (of the Illinois 
rules) or paragraph if it is subject to the limits of that subpart (of 
the Illinois rules) or paragraph. An emission source is not considered 
regulated by a subpart (of the Illinois rules) or paragraph of its 
emissions are below the applicability cutoff level or if the source is 
covered by an exemption.
    (v) The control requirements in paragraphs (u), (v), (w), and (x) of 
this section shall not apply to sewage treatment plants, vegetable oil 
processing plants, coke ovens (including by-product recovery plants), 
fuel combustion sources, bakeries, barge loading facilities, jet engine 
test cells, pharmaceutical manufacturing, production of polystyrene foam 
insulation board (including storage and extrusion of scrap where blowing 
agent is added to the polystyrene resin at the plant), production of 
polystyrene foam packaging (not including storage and extrusion of scrap 
where blowing agent is added to the polystyrene resin at the plant), and 
iron and steel production.
    (2) Permit conditions. No person shall violate any condition in a 
permit when the condition results in exclusion of the plant or an 
emission source from paragraph (x) of this section.
    (3) Control requirements. Every owner or operator of an emission 
source subject to paragraph (x) of this section shall comply with the 
requirements of paragraph (x)(3) (i), (ii) or (iii) of this section.
    (i) Emission capture and control equipment which achieve an overall 
reduction in uncontrolled VOM emissions of at least 81 percent, or
    (ii) For coating lines, the daily-weighted average VOM content shall 
not exceed 0.42 kg VOM/l (3.5 lbs VOM/gal) of coating (minus water and 
any compounds which are specifically exempted from the definition of 
VOM) as applied during any day. Owners and operators complying with this 
paragraph

[[Page 394]]

are not required to comply with section 215.301 of 35 Ill. Adm. Code 215 
(incorporated by reference as specified in 40 CFR 52.742), or
    (iii) An alternative control plan which has been approved by the 
Administrator as a SIP or FIP revision.
    (4) Compliance schedule. Every owner or operator of an emissions 
source which is subject to paragraph (x) of this section shall comply 
with the requirements of paragraph (x) of this section on and after July 
1, 1991.
    (5) Testing. Any owner or operator of a VOM emission source which is 
subject to paragraph (x) of this section shall demonstrate compliance 
with paragraph (x)(3) of this section by using the applicable test 
methods and procedures specified in paragraph (a)(4) of this section.
    (6) The control requirements in this paragraph apply to the varnish 
operations at the General Motors Corporation, Electro-Motive Division 
Plant (GMC Electro-Motive), LaGrange, Illinois, instead of the control 
requirements in paragraph (x)(3) of this section.
    (i) After July 1, 1991, no coatings shall at any time be applied 
which exceed the following emission limitations for the specified 
coating.
    (A) 8.0 lbs VOM per gallon of coating (minus water and any compounds 
which are specifically exempted from the definition of VOM) as applied 
at each coating applicator to coat Nomex rings. Such coating consists of 
Monsanto Skybond 705 Polyamide Resin (EMD P/N 9088817) and diluents. The 
Administrator must be notified at least 10 days prior to the use of any 
replacement coating(s) and/or diluents for coating Nomex rings.
    (B) 6.8 lbs VOM per gallon of coating (minus water and any compounds 
which are specifically exempted from the definition of VOM) as applied 
at each coating applicator for any coatings not specified in paragraph 
(x)(6)(i)(A) of this section.
    (ii) After July 1, 1991, the volume of coatings used shall not 
exceed the following:
    (A) 600 gallons per year total for all coatings specified in 
paragraph (x)(6)(i)(A) of this section. The yearly volume of coatings 
used are to be calculated as follows:
    (1) Compute the volume of specified coating used each month by the 
15th of the following month.
    (2) By the 15th of each month, add the monthly coating use for the 
12 previous months (to obtain the yearly volume of coatings used).
    (B) 28,500 gallons per year total for all coatings other than those 
specified in paragraph (x)(6)(i)(A) of this section. The yearly volume 
of coatings used are to be calculated as specified in paragraphs 
(x)(6)(ii)(A)(1) and (x)(6)(ii)(A)(2) of this section.
    (iii) Beginning on July 1, 1991, the owner and operator of the 
General Motors Corporation Electro-Motive Division Plant in LaGrange, 
Illinois shall keep the following records for each month. All records 
shall be retained at General Motors for 3 years and shall be made 
available to the Administrator on request.
    (A) The name and identification number of each coating as applied on 
any coating line within the varnish operation.
    (B) The weight of VOM per volume and the volume of each coating 
(minus water and any compounds which are specifically exempted from the 
definition of VOM) as applied each month on any coating line within the 
varnish operation.
    (7) The control, recordkeeping, and monitoring requirements in this 
paragraph apply to the aluminum rolling mills at the Reynolds Metals 
Company's McCook Sheet & Plate Plant in McCook, Illinois (Cook County) 
instead of the control requirements and test methods in the other parts 
of paragraph (x), and the recordkeeping requirements in paragraph (y) of 
this section. All of the following requirements must be met by Reynolds 
on and after July 7, 1995.
    (i) Only organic lubricants with initial and final boiling points 
between 460 degrees F and 635 degrees F, as determined by a distillation 
range test using ASTM method D86-90, are allowed to be used at Reynolds' 
aluminum sheet cold rolling mills numbers 1 and 7. All incoming 
shipments of organic lubricant for the number 1 and

[[Page 395]]

7 mills must be sampled and each sample must undergo a distillation 
range test to determine the initial and final boiling points using ASTM 
method D86-90. A grab rolling lubricant sample shall be taken from each 
operating mill on a monthly basis and each sample must undergo a 
distillation range test, to determine the initial and final boiling 
points, using ASTM method D86-90.
    (ii) An oil/water emulsion, with no more than 15 percent by weight 
of petroleum-based oil and additives, shall be the only lubricant used 
at Reynolds' aluminum sheet and plate hot rolling mills, 120 inch, 96 
inch, 80 inch, and 145 inch mills. A grab rolling lubricant sample shall 
be taken from each operating mill on a monthly basis and each sample 
shall be tested for the percent by weight of petroleum-based oil and 
additives by ASTM Method D95-83.
    (iii) The temperature of the inlet supply of rolling lubricant for 
aluminum sheet cold rolling mills numbers 1 and 7 shall not exceed 150  
deg.F, as measured at or after (but prior to the lubricant nozzles) the 
inlet sump. The temperature of the inlet supply of rolling lubricant for 
the aluminum sheet and plate hot rolling mills, 120 inch, 96 inch, 80 
inch, and 145 inch mills shall not exceed 200  deg.F, as measured at or 
after (but prior to the lubricant nozzles) the inlet sump. Coolant 
temperatures shall be monitored at all the rolling mills by use of 
thermocouple probes and chart recorders or electronic data recorders.
    (iv) All distillation test results for cold mill lubricants, all 
percent oil test results for hot mill lubricants, all coolant 
temperature recording charts and/or temperature data obtained from 
electronic data recorders, and all oil/water emulsion formulation 
records, shall be kept on file, and be available for inspection by 
USEPA, for three years.
    (8) The control and recordkeeping requirements in this paragraph 
apply to the silk screen presses and associated ovens, cleaning 
operations and laminators at Parisian's Novelty Company (Parisian), 
Chicago, Illinois, facility, instead of the control requirements in 
paragraphs (x)(8) (u)(3) and (x)(3) of this section and the 
recordkeeping requirements in paragraph (x)(8)(y) of this section.
    (i) After March 1, 1993, no coatings or inks shall at any time be 
applied, at any coating or ink applicator, which exceed the following 
emission limitations for the specified coating or ink.
    (A) 6.65 pounds (lbs) volatile organic material (VOM) per gallon of 
ink (minus water and any compounds which are specifically exempted from 
the definition of VOM) as applied on Parisian's silk screen presses.
    (B) 6.4 lbs VOM per gallon of adhesive coating (minus water and any 
compounds which are specifically exempted from the definition of VOM) as 
applied on Parisian's laminators. Such adhesive is identified as MIX 
#963.
    (ii) After March 1, 1993, the volume of coating and ink used shall 
not exceed the following:
    (A) 2,556 gallons per year total for all inks. The yearly volume of 
inks used is to be calculated as follows:
    (1) Compute the volume of ink used each month by the 15th of the 
following month.
    (2) By the 15th of each month, add the monthly ink usage for the 12 
previous months (to obtain the yearly volume of ink used).
    (B) 780 gallons per year total for all coatings specified in 
paragraph (x)(8)(i)(B) of this section. The yearly volume of coatings 
used are to be calculated as specified in paragraphs (x)(8)(ii)(A)(1) 
and (x)(8)(ii)(A)(2) of this section.
    (iii) Beginning on March 1, 1993, the owner and operator of 
Parisian's plant in Chicago, Illinois, shall keep the following records 
for each month. All records shall be retained at Parisian for 3 years 
and shall be made available to the Administrator on request.
    (A) The name and identification number of each coating as applied on 
any laminator.
    (B) The weight of VOM per volume and the volume of each coating 
(minus water and any compounds which are specifically exempted from the 
definition of VOM) as applied each month on any laminator.
    (C) The weight of VOM per volume and the volume of each type of ink 
(minus water and any compounds which are specifically exempted from

[[Page 396]]

the definition of VOM) as applied each month on any screen press.
    (iv) After March 1, 1993, no more than 84 gallons per year of 
denatured alcohol may be used for cleaning labels at Parisian. The 
yearly volume of denatured alcohol used is to be calculated as specified 
in paragraphs (x)(8)(ii)(A)(1) and (x)(8)(ii)(A)(2) of this section. 
Beginning on March 1, 1993, Parisian shall keep monthly records of the 
type, volume, and VOM content of all solvents used for label cleaning. 
These records shall be retained at Parisian for 3 years and shall be 
made available to the Administrator on request.
    (v) After March 1, 1993, no more than 7,932 gallons per year of 
screen wash #956 may be used on Parisian's screen cleaner. The yearly 
volume of screen wash #956 used is to be calculated as specified in 
paragraphs (x)(8)(ii)(A)(1) and (x)(8)(ii)(A)(2) of this section. 
Beginning on March 1, 1993, Parisian shall keep monthly records of the 
type, volume, and VOM content of all cleaning compounds used on 
Parisian's screen cleaner. These records shall be retained at Parisian 
for 3 years and shall be made available to the Administrator on request.
    (vi) After March 1, 1993, only those cleaners specifically 
identified in paragraphs (x)(8)(iv) and (x)(8)(v) of this section may be 
used at Parisian.
    (9) The control requirements in this paragraph apply to the process 
sources listed in paragraph (x)(9)(i)(A) of this section at the Nalco 
Chemical Company facility in Bedford Park, Illinois, instead of the 
control requirements in paragraph (x)(3) of this section.
    (i) Production and Operation Restrictions.
    (A) On and after October 1, 1992, the maximum volatile organic 
compound (VOC) emissions per batch, the 12-month rolling average number 
of batches per year, and the peak limit of batches per month shall not 
exceed the following limits:

[[Page 397]]



------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
                                       Maximum VOC emissions, lb/
               Source                             batch                           12-mo. rolling average limit batch/yr                              Peak batch limit, batch/month
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
(1) System 1 charge.................  0.16........................  280..............................................................  33.
    System 1 purge..................  1.35........................  .................................................................  .........................................................
(2) 24-T-156, 157...................  2.60........................  300..............................................................  33.
(3) 28-T-217, 234...................  0.23........................  402..............................................................  45.
(4) 28-T-214-216....................  5.70........................  603..............................................................  65.
(5) 20-R-182, 185...................  0.02........................  72...............................................................  8.
(6) 20-R-130........................  0.07........................  340..............................................................  38.
(7) 20-R-155........................  0.21........................  254..............................................................  29.
(8) 20-WT-174.......................  0.21........................  254..............................................................  29.
(9) 12-T-97-99......................  4.6E-4 lb/hr................  8,760 hr/yr......................................................  744 hr/mo.
(10) 12-T-95........................  4.0E-6 lb/hr................  8,760 hr/yr......................................................  744 hr/mo.
(11) 12-T-96........................  7.7E-5 lb/hr................  8,760 hr/yr......................................................  744 hr/mo.
(12) 12-T-67, 73....................  0.003 lb/hr.................  8,760 hr/yr......................................................  744 hr/mo.
(13) 20-T-121-122...................  0.85........................  312..............................................................  34.
(14) 20-T-123-125...................  5.4.........................  616..............................................................  68.
(15) 20-T-140, 142..................  8.0.........................  600..............................................................  65.
(16) 20-T-159.......................  0.31........................  416..............................................................  46.
(17) 20-R-193, 200..................  9.8.........................  540..............................................................  59.
(18) 32-R-300.......................  0.18........................  365..............................................................  41.
(19) 32-T-302.......................  0.21........................  365..............................................................  41.
(20) 32-T-304.......................  0.21........................  730..............................................................  81.
(21) 32-T-314.......................  0.23........................  365..............................................................  41.
(22) 32-T-322.......................  0.21........................  365..............................................................  41.
(23) 32-T-328.......................  0.23........................  365..............................................................  41.
(24) 10-T-61........................  0.001.......................  365--containing organic..........................................  31--containing organic.
(25) 24-T-441, 166..................  0.12........................  730..............................................................  81.
(26) 25-T-284, 440, 443-444.........  0.28........................  730..............................................................  81.
(27) 25-T-170.......................  4E-6........................  104..............................................................  12.
(28) Tank truck loading.............  0.12 lb/truck...............  1,600 trucks/yr..................................................  134 trucks/mo.
(29) System 2.......................  0.36........................  280..............................................................  33.
(30) System 4.......................  2.88........................  280..............................................................  33.
(31) 25-R-164.......................  0.10........................  365..............................................................  41.
(32) 25-R-205.......................  0.14........................  365..............................................................  41.
(33) Drum station...................  3.51........................  1,005............................................................  110.
(34) V-4SAC.........................  1.56........................  254..............................................................  29.
(35) 20-CT-155......................  13.90.......................  254..............................................................  29.
(36) 12-SE-100......................  1.10 lb/hr..................  8,760 hr/yr......................................................  744 hr/mo.
(37) Drum exhaust hood A............  1.00........................  365--involving use of organic material...........................  31--involving use of organic material.
(38) 24-T-230.......................  0.98........................  730..............................................................  81.
(39) 8-CT-1.........................  0.002 lb/hr.................  8,760 hr/yr......................................................  744 hr/mo.
(40) 9-CT-1.........................  0.002 lb/hr.................  8,760 hr/yr......................................................  744 hr/mo.
(41) 10-CT-1........................  0.005 lb/hr.................  8,760 hr/yr......................................................  744 hr/mo.
(42) 22-CT-1........................  0.003 lb/hr.................  8,760 hr/yr......................................................  744 hr/mo.
(43) 25-CT-1........................  0.005 lb/hr.................  8,760 hr/yr......................................................  744 hr/mo.
(44) 25-CT-2........................  0.002 lb/hr.................  8,760 hr/yr......................................................  744 hr/mo.
(45) 29-CT-1........................  0.002 lb/hr.................  8,760 hr/yr......................................................  744 hr/mo.
(46) 32-CT-1........................  0.005 lb/hr.................  8,760 hr/yr......................................................  744 hr/mo.

[[Page 398]]

(47) 36-CT-1........................  0.002 lb/hr.................  8,760 hr/yr......................................................  744 hr/mo.
(48) 32-T-325.......................  0 a.........................  365..............................................................  41.
(49) 26-R-195.......................  0.1 a.......................  365..............................................................  41.
(50) Continuous polymer-blending....  0.1 lb/hr a.................  2,000 hr/yr......................................................  .........................................................
(51) Portafeed washer booth 1.......  0.84 lb/hr b................  4,160 hr/yr......................................................  744 hr/mo.
(52) Portafeed washer booth 2.......  0.84 lb/hr b................  8,736 hr/yr......................................................  744 hr/mo.
(53) 32-T-392.......................  4.4E-7......................  104..............................................................  12.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
a Assumed value.
b Based on monitoring data.

[[Page 399]]


    (B) The following equation shall be used to calculate maximum VOC 
emissions per batch for the process sources listed in paragraphs 
(x)(9)(i)(A)(1) (charge only and (2) through (28) and (53) of this 
section:
Where:

ER = VOC emission rate;
Qo = Quantity of organic per batch or charge rate;
[GRAPHIC] [TIFF OMITTED] TR21MR95.000

Mv = Molecular weight of the volatile component;
P = Partial pressure of the volatile component for mixtures of liquid 
made up with more than one chemical; or vapor pressure for pure liquids 
made up of only one organic chemical; and
Constant 1 = (7.45 gal/ft3)x(385 ft3/
mole)x(760 mmHg).

    (C) The following equation shall be used to calculate the VOC 
emissions per batch from the process sources listed in paragraph 
(x)(9)(i)(A)(1) of this section (purge only) and (29) through (32) of 
this section:
[GRAPHIC] [TIFF OMITTED] TR21MR95.001

Where:

PR=Nitrogen purge rate; and
Constant 2 = (385 ft3/mole)x(760 mmHg).

(D) The following equation shall be used to calculate the VOC emissions 
per batch from the drum station listed at paragraph (x)(9)(i)(A)(33) of 
this section:

ER(1b/batch) = (0.40 x [ER28-T-217-218])+(0.60 x 
[ER28-T-214-216])

    (E) The following equation shall be used to calculate the VOC 
emissions per batch from the V-4SAC listed at paragraph (x)(9)(i)(A)(34) 
of this section:
[GRAPHIC] [TIFF OMITTED] TR21MR95.002

Where:

FR1mmHg = Maximum air flow rate to maintain 1 mmHg;
Ma = Molecular weight of air; and
Pv2 = Vapor pressure of organic at 65  deg.F and 760 mmHg.

    (F) The following equation shall be used to calculate the VOC 
emissions per batch from 20-CT-155 listed at paragraph (x)(9)(i)(A)(35) 
of this section:
[GRAPHIC] [TIFF OMITTED] TR21MR95.003


[[Page 400]]


Where:

ERtot = Total system emission rate calculated using the 
following equation:
  
  
  
[GRAPHIC] [TIFF OMITTED] TR21MR95.004

Where:

Pv1 = Vapor pressure of organic at 200  deg.F and 350 mmHg.

    (G) The following equation shall be used to calculate the VOC 
emissions per hour from 12-SE-100 listed at paragraph (x)(9)(i)(A)(36) 
of this section:

ER(lb/hr) = Evap (gm/cm2 sec)  x  area (cm2)  x  
3600 sec/hr

Where:

Evap = Evaporation rate from a surface 8.93 cm  x  8.9 cm (lb/
[cm2] [sec]) calculated using the following equation:

Evap = 10-7 Mv0.71  x  [0.034 (Pe - 
Pd) 1.25 + 156 (Pe - Pd)]

Where:

Pe = Partial pressure of the component from the spilled 
liquid;
Pd = Partial pressure of the component in the incident air 
stream, assumed to be 0 mmhg; and
Area = Surface area of the liquid.

    (H) The following equation shall be used to calculate the VOC 
emissions per batch from the drum exhaust hood A listed at paragraph 
(x)(9)(i)(A)(37) of this section:
[GRAPHIC] [TIFF OMITTED] TR21MR95.005

Where:

FR = Air flow rate.

(I) The following equation shall be used to calculate the VOC emissions 
per batch from 24-T-230 listed at paragraph (x)(9)(i)(A)(38) of this 
section:
[GRAPHIC] [TIFF OMITTED] TR21MR95.006

Where:

VH = Head space volume at heated temperature 135 deg.F;
VA = Head space volume at ambient temperature 68 deg.F;
PP135 deg.F = Partial pressure of volatile component at 
135 deg.F.
Constant 3 = (434 ft3/mole)(7.45 gal/
ft3)x(760 mmHg)

(J) The following equations shall be used to calculate the VOC emissions 
per batch from the process sources listed in paragraph (x)(9)(i) (39) 
through (47) of this section:

[[Page 401]]

[GRAPHIC] [TIFF OMITTED] TR21MR95.007


Where:

VR = Refill volume;
t = Time between refills;
org = Fraction of organic component in product;
CB = Concentration of chemical B fed 3 times/week;
VT = Tower volume;
dB = Density of chemical B;
CC = Concentration of chemical C fed continuously;
Evap = Evaporation rate; and
dc = Density of chemical C.

    (K) The number of batches for each process source shall be 
calculated as follows:
    (1) Compute the monthly number of batches for each process source by 
the 15th day of the following month.
    (2) By the 15th day of each month, add the monthly number of batches 
for each process source for the 12 previous months to obtain the total 
number of batches per year.
    (ii) Recordingkeeping.
    (A) On and after October 1, 1992, the owner and operator of the 
Nalco Chemical Company facility in Bedford Park, Illinois, shall keep 
the following records for all process sources listed in paragraphs 
(x)(9)(i)(A) (1) through (53) of this section. These records shall be 
maintained for the units specified in paragraphs (x)(9)(i) (A) through 
(K) of this section, be compiled on a monthly basis, be retained at the 
facility for a period of 3 years, and be made available to the 
Administrator upon request.
    (B) [Reserved]
    (1) Calculations of the pounds per batch or pounds per hour (as 
appropriate) for each batch for each process source. This includes the 
information necessary for each calculation.
    (2) The monthly number of batches for each process source.
    (3) The total number of batches per year for the 12 previous months 
for each process source.
    (10) The control requirements in this paragraph apply to the storage 
tanks listed in paragraph (x)(10)(i)(A) of this section at the Nalco 
Chemical Company facility in Bedford Park, Illinois, instead of the 
control requirements in paragraph (x)(3) of this section.
    (i) Production and Operation Restrictions.
    (A) On and after October 1, 1992, the product of the molecular 
weight of vapor in each storage tank (Mv), the true vapor 
pressure at bulk liquid conditions for each tank (P), and the paint 
factor (Fp); the storage tank maximum yearly throughput for 
each tank; and the maximum monthly throughput for each tank shall not 
exceed the following limits:

------------------------------------------------------------------------
                                MV  x  P  x
                                 Fp, (lb)        Yearly        Monthly
           Tank No.             (mmhg)/lb-     throughput,   throughput,
                                   mole          gal/yr       gal/month
------------------------------------------------------------------------
(1) 24-T-147.................         45.4           56,250        4,688
(2) 24-T-150.................        227            266,450       22,204
(3) 24-T-151.................        227            266,450       22,204
(4) 24-T-158N................         18.9          173,830       14,486
(5) 24-T-158C................         18.0          110,190        9,183
(6) 24-T-158S................          1.17          52,010        4,334
(7) 24-T-160.................        226.8          266,450       22,204
(8) 24-T-161.................        227            182,450       15,204
(9) 24-T-162.................        473             93,900        7,825
(10) 20-T-101................          3.72          90,290        7,525
(11) 20-T-102................          1.80         122,900       10,242
(12) 20-T-103................        420             23,960        1,997

[[Page 402]]

(13) 20-T-104................        180            475,900       39,659
(14) 20-T-105................        370             52,360        4,363
(15) 20-T-106................      1,210            623,100       51,926
(16) 20-T-107................        294             90,040        7,503
(17) 20-T-108................      1,360             81,470        6,789
(18) 20-T-109................      1,390            167,060       13,922
(19) 20-T-153................        180             35,000        2,917
(20) 20-T-131 a..............  ............  ..............  ...........
(21) 20-T-132 a..............  ............  ..............  ...........
(22) 20-T-133 a..............  ............  ..............  ...........
(23) 20-T-134 a..............  ............  ..............  ...........
(24) 20-T-135 a..............  ............  ..............  ...........
(25) 20-T-136................         29.5          307,710       26,580
(26) 20-T-137 a..............  ............  ..............  ...........
(27) 20-T-138................         29.5          307,710       26,580
(28) 32-T-305................        288            785,550       65,462
(29) 32-T-306................         66.5          165,350       13,779
(30) 32-T-307................         66.5          294,750       24,563
(31) 32-T-308................         66.5          128,470       10,706
(32) 32-T-310................         66.5           77,290        6,441
(33) 32-T-311................         66.5          182,130       15,177
(34) 32-T-319................         50.0          688,950       57,413
(35) 32-T-320................         50.0          688,950       57,413
(36) 32-T-326................         70.0          248,440       20,703
(37) 32-T-331................         70.0          489,540       40,795
(38) 32-T-332................         70.0           70,380        5,865
(39) 32-T-333................         70.0          270,850       22,571
(40) 32-T-334................         70.0          210,610       18,267
(41) 32-T-335................         70.0          418,200       34,850
(42) 32-T-336................         70.0          632,460       52,706
(43) 32-T-337................        798             53,850        4,488
(44) 17-T-206................     27,000            300,760       25,063
(45) 17-T-208................     27,000            300,760       25,063
(46) 17-T-207................          2.48         180,180       15,016
(47) 17-T-209................          2.48         180,180       15,016
(48) 24-T-515................        331            216,860       18,072
(49) 25-T-282................          1.42       1,920,410      160,034
(50) 25-T-283................          1.42       1,920,410      160,034
(51) 24-T-442................         18.0           90,990        7,583
(52) 17-T-210................         47.9          582,990       48,583
(53) 17-T-211................         47.9          582,990       48,583
(54) 17-T-212................        508            728,420       60,702
(55) 17-T-213................        508            728,420       60,702
(56) 17-T-401................         50.0          131,970       10,998
(57) 17-T-402................         15.0          120,160       10,014
(58) 17-T-403................          6.20         127,770       10,648
(59) 17-T-404................         26.5        1,601,510      133,460
(60) 17-T-405................         50.0          113,830        9,486
(61) 17-T-406................         40.0          231,030       19,253
(62) 17-T-407................        206            135,180       11,265
(63) 17-T-409................        395            327,410       27,285
(64) 17-T-410................        395            129,290       10,774
(65) 17-T-411................         50.0          213,870       17,843
(66) 17-T-412................         50.0          277,840       23,153
(67) 17-T-414................         50.0           72,920        6,077
(68) 17-T-415................         50.0           56,140        4,678
(69) 17-T-416................        395            393,550       32,796
(70) 17-T-417................         23.4          233,780       19,482
(71) 17-T-418................        115            873,270       72,773
(72) 17-T-419................        119            278,460       23,205
(73) 17-T-420................        112            730,780       60,898
(74) 17-T-421................         25.2          300,010       25,001
(75) 17-T-422................        115            873,270       72,773
(76) 17-T-423................         23.4          215,060       17,922
(77) 17-T-424................         23.4          209,610       17,468
(78) 26-T-218................         50.0           64,890        5,408
(79) 26-T-219................          1.50         197,900       16,492
(80) 26-T-220................      2,460            160,020       13,336
(81) 26-T-221................         50.0           74,820        6,235
(82) 26-T-222................         80.0           66,590        5,550
(83) 26-T-224................          4.80         225,290       18,774
(84) 26-T-225................         50.0           36,610        3,051

[[Page 403]]

(85) 26-T-226................        294             47,390        3,949
(86) 26-T-227................         50.0           63,040        5,253
(87) 26-T-228................        500            136,150       11,346
(88) 26-T-229................         50.0          112,970        9,414
(89) 26-T-231................         23.4          319,610       26,634
(90) 26-T-232................        117            564,280       47,024
(91) 26-T-233................         23.4          539,700       44,975
(92) 27-T-245................         21.6          361,970       30,165
(93) 27-T-246................        348            141,820       11,818
(94) 27-T-247................         23.4           71,670        5,972
(95) 27-T-248................        198             96,010        8,001
(96) 27-T-249................        927             51,240        4,270
(97) 27-T-250................        110            433,030       36,086
(98) 27-T-251................        396             45,440        3,787
(99) 27-T-252................         21.6          171,370       14,281
(100) 27-T-253...............        348            237,900       19,825
(101) 26-T-192...............         10.0          117,950        9,829
(102) 27-T-278...............          0.62          74,910        6,243
(103) 27-T-279...............          0.18         583,760       48,647
(104) 27-T-285...............         21.6          459,530       38,294
(105) 27-T-286...............         21.6          459,530       38,294
(106) 25-T-201...............         19.8          143,550       11,963
(107) 32-T-388...............          0.07         499,340       41,612
(108) 32-T-389...............          0.07         499,340       41,612
(109) 32-T-390...............        288            808,310      583,340
(110) 32-T-391...............          1.42          800,00      583,340
------------------------------------------------------------------------
a Tank not in use.

    (B) The throughput shall be calculated as follows:
    (1) Compute the monthly throughput for each tank by the 15th day of 
the following month.
    (2) By the 15th day of each month, add the monthly throughputs for 
the 12 previous months to obtain the yearly throughput.
    (ii) Recordkeeping. (A) On and after October 1, 1992, the owner and 
operator of the Nalco Chemical Company facility in Bedford Park, 
Illinois, shall keep the following records for all storage tanks. These 
records shall be compiled on a monthly basis, be retained at the 
facility for a period of 3 years, and be made available to the 
Administrator upon request.
    (1) The molecular weight of vapor in each storage tank 
(Mv), the true vapor pressure at bulk liquid conditions for 
each tank (P), the paint factor (Fp), and their product. 
Fp shall be determined from Table 4.3-1 of ``Compilation of 
Air Pollutant Emission Factors, Volume I: Stationary Point and Area 
Sources,'' AP-42, September 1985.
    (2) The monthly throughput.
    (3) The total throughput per year for the 12 previous months.
    (B) [Reserved]
    (iii) Test Methods. (A) The true vapor pressure at bulk liquid 
temperature shall be determined by using the procedures specified in 
paragraph (a)(8) of this section.
    (B) The molecular weight of vapor in the storage tank shall be 
determined by using Table 4.3-2 ``Compilation of Air Pollutant Emission 
Factors, Volume I: Stationary Point and Area Sources,'' AP-42, September 
1985, or by analysis of vapor samples. Where mixtures of organic liquids 
are stored in a tank, Mv shall be estimated from the liquid 
composition using the following equation:
[GRAPHIC] [TIFF OMITTED] TR21MR95.008


[[Page 404]]


Where:

Ma=Molecular weight of pure component a;
Pa=Vapor pressure of pure component a;
Xa=Mole fraction of pure component a in the liquid;
Mb=Molecular weight of pure component b;
Pb=Vapor pressure of pure component b;
Xb=Mole fraction of pure component b in the liquid; and
Pt=Pa X2+ Pb Xb.

    (11) The control requirements in this paragraph apply to the 
fugitive emission sources listed in paragraph (x)(11)(i)(A) of this 
section at the Nalco Chemical Company facility in Bedfore Park, 
Illinois, instead of the control requirements in paragraph (x)(3) of 
this section.
    (i) Production and Operation Restrictions.
    (A) On and after October 1, 1992, all components (e.g., pumps, 
valves, flanges, pressure relief valves (PRV's), and open end lines) at 
the specified locations (e.g., Building 32--Tube Reactor System, etc.), 
and in the specified type of service (e.g., heavy liquid stratified, 
light liquid stratified, etc.) shall be limited by the maximum monthly 
hours in the following table:
    (ii) Recordkeeping.
    (A) On and after October 1, 1992, the owner and operator of the 
Nalco Chemical Company facility in Bedford Park, Illinois, shall keep 
the following records for all fugitive emission sources. These records 
shall be compiled on a monthly basis, be retained at the facility for a 
period of 3 years, and be made available to the Administrator upon 
request.
    (1) The total number of hours of organic service for each component 
at each location specified in paragraphs (x)(11)(i)(A) (1) through (10) 
of this section.
    (2) The vapor pressure of each organic compound in each component at 
each location specified in paragraphs (x)(11)(i)(A) (1) through (10) of 
this section.
    (B) [Reserved]
    (12) The control and recordkeeping and reporting requirements, as 
well as the test methods in this paragraph, apply to the gravure and 
screen press operations at the Meyercord Corporation (Meyercord) in 
Carol Stream, Illinois, instead of the requirements in paragraphs (x)(1) 
through (x)(5) of this section.
    (i) After July 1, 1991, no materials which contain volatile organic 
material (VOM), including coatings, inks, and cleaning material, may be 
used at any gravure or screen press unless the total VOM emissions 
remain below 100 tons of VOM for every consecutive 365-day period, or 
fraction thereof, starting on July 1, 1991. A new 365-day period starts 
on each day. The VOM emissions, which are to be calculated on a daily 
basis, are to be added to the VOM emissions for the prior 364 days (but 
not including any day prior to July 1, 1991). VOM emissions are based 
upon the VOM content of the material and the volume of material used. 
The effect of add-on control equipment is not considered in calculating 
VOM emissions; that is, the VOM emissions are to be determined as if the 
press(es) do(es) not have add-on control equipment. The applicable test 
methods and procedures specified in paragraph (a)(4) of this section are 
to be used in determining daily VOM emissions.
    (ii) The VOM content of each coating, ink, and cleaning solution 
shall be determined by the applicable test methods and procedures 
specified in paragraph (a)(4) of this section to establish the records 
required under paragraph (x)(12)(ii) of this section. Beginning on July 
1, 1991, the owner or operator of the subject presses shall collect and 
record all of the following information each day and maintain the 
information at the facility for 3 years:
    (A) The name and identification number of each coating, ink, and 
cleaning solution as applied on any press.
    (B) The pounds (lbs) of VOM per gallon of each coating, ink, and 
cleaning solution (minus water and any compounds which are specifically 
exempted from the definition of VOM) as applied on any press.
    (C) The total gallons of each coating, ink, and cleaning solution 
(minus water and any compounds which are specifically exempted from the 
definition of VOM) used per day.

[[Page 405]]

    (D) The total lbs of VOM contained in the volume of each coating, 
ink, and cleaning solution used per day on any press. The lbs of VOM per 
day is to be calculated by multiplying the lbs of VOM per gallon (minus 
water and any compounds which are specifically exempted from the 
definition of VOM) times the gallons (minus water and any compounds 
which are specifically exempted from the definition of VOM) used per 
day.
    (E) The total lbs of VOM per day from all coatings, inks, and 
cleaning solutions used on all presses. The total lbs of VOM per day is 
to be obtained by adding the lbs of VOM per day contained in all 
coatings, inks, and cleaning solutions.
    (F) Within 7 days after each 365-day period, the VOM emissions (as 
calculated in paragraph (x)(12)(ii)(E)) of this section before add-on 
control, from the 365-day period, are to be determined.
    Starting on July 7, 1992, VOM emissions are to be determined for the 
365 days ending 7 days earlier. Each day concludes a new 365-day period. 
However, no VOM emissions are to be included for any days prior to July 
1, 1991. For example, on July 17, 1991, the emissions from July 1, 
through July 10, 1991, are to be included, whereas on January 7, 1994, 
the emissions from January 1, 1993, through December 31, 1993, are to be 
included.
    (13) The control and recordkeeping and reporting requirements, as 
well as the test methods in this paragraph, apply to the sheet fed cold 
set presses and web heatset presses at the Wallace Computer Services, 
Inc. (Wallace) printing and binding plant in Hillside, Illinois, instead 
of the requirements in 40 CFR 52.741(h) and 40 CFR 52.741(x)(1) through 
40 CFR 52.741(x)(5).
    (i) After July 1, 1991, no inks shall at any time be applied, at the 
presses indicated below, which exceed the pounds (lbs) volatile organic 
material (VOM) per gallon of ink (minus water and any compounds which 
are specifically exempted from the definition of VOM) limit established 
for each press. After July 1, 1991, the yearly volume of ink used at 
each press, in gallons of ink (minus water and any compounds which are 
specifically exempted from the definition of VOM) per year, shall not 
exceed the gallons per year limit established below for each press. The 
yearly volume of ink used per press is to be calculated according to the 
procedure in paragraph (x)(13)(iii) of this section.

------------------------------------------------------------------------
                                                      Lbs VOM/
                        Press                          gallon   Gallons/
                                                        ink     year ink
------------------------------------------------------------------------
14..................................................     1.68        276
16..................................................     1.68       1896
22..................................................     3.01       2712
23..................................................     3.01      13140
25..................................................     3.01      12720
26..................................................     3.01       4764
------------------------------------------------------------------------

    (ii) After July 1, 1991, no materials (other than those inks subject 
to the limits in paragraph (x)(13)(i)) of this section, shall at any 
time be applied or used, at the presses indicated below, which exceed 
the lbs VOM per gallon of material (minus water and any compounds which 
are specifically exempted from the definition of VOM) limit established 
for each press. After July 1, 1991, the yearly volume of material 
(excluding ink and water) used at each press, in gallons of material 
(minus water and any compounds which are specifically exempted from the 
definition of VOM) per year, shall not exceed the gallons per year limit 
established for each press. The yearly volume of material (excluding ink 
and water) used per press is to be calculated according to the procedure 
in paragraph (x)(13)(iii) of this section.

------------------------------------------------------------------------
                                                     Lbs VOM/   Gallons/
                       Press                          gallon      year
                                                     material   material
------------------------------------------------------------------------
14.................................................       6.9        612
16.................................................       6.9      8,340
22.................................................       7.1        360
23.................................................       7.1        480
25.................................................       7.1        516
26.................................................       7.1      1,848
------------------------------------------------------------------------

    (iii) The yearly volume of ink/material used is to be calculated as 
follows:
    (A) Compute the volume of ink/material used each month per press by 
the 15th of the following month.
    (B) By the 15th of each month, add the monthly ink/material usage 
per press for the 12 previous months (to obtain the yearly volume of ink 
used).

[[Page 406]]

    (iv) Beginning on July 1, 1991, the owner and operator of Wallace's 
plant in Hillside, Illinois, shall keep the following records for each 
press for each month. All records shall be retained by Wallace for 3 
years and shall be made available to the Administrator on request:
    (A) The name and identification number of each ink, fountain 
solution, fountain solution additive, cleaning solvent, and other VOM 
containing material as applied or used.
    (B) The weight of VOM per volume of each ink, fountain solution, 
fountain solution additive, cleaning solvent, and each other VOM 
containing material (minus water and any compounds which are 
specifically exempted from the definition of VOM) as applied or used 
each month.
    (C) The volume of ink (minus water and any compounds which are 
specifically exempted from the definition of VOM) as applied each month.
    (D) The total volume of miscellaneous VOM containing materials 
(minus water and any compounds which are specifically exempted from the 
definition of VOM), other than inks, that are used each month.
    (v) Any record showing a violation of paragraph (x)(13)(i) or 
(x)(13)(ii) of this section shall be reported by sending a copy of such 
record to the Administrator within 30 days of the violation.
    (vi) To determine compliance with paragraphs (x)(13)(i) and 
(x)(13)(ii) of this section and to establish the records required under 
paragraph (x)(13)(iv) of this section the VOM content of each ink and 
miscellaneous VOM containing material shall be determined by the 
applicable test methods and procedures specified in paragraph (a)(4) of 
this section.
    (14) The control and recordkeeping and reporting requirements, as 
well as the test methods in this paragraph, apply to the power-operated 
silk screen presses, the hand screen presses, the screen adhesive 
printing lines, the Andreotti rotogravure press, the Halley Rotogravure 
press, and the Viking press at the American Decal and Manufacturing 
Company's plant in Chicago, Illinois, instead of the requirements in 
paragraphs (h) and (x)(1) through (x)(5) of this section. The emissions 
from the sources listed above (in paragraph (x)(14) of this section) are 
to be included in the calculation of ``maximum theoretical emissions'' 
for determining applicability for any other sources (for which 
applicability is based on the quantity of maximum theoretical emissions) 
at American Decal and Manufacturing Company's Chicago plant not included 
in paragraph (x)(14) of this section.
    (i) After July 24, 1992, no inks, coatings, thinner, clean-up 
material or other VOC-containing material shall at any time be applied, 
at the presses/printing lines listed above (in paragraph (x)(14) of this 
section), which exceed the VOC content (in percent by weight VOC) limit 
established below. After July 24, 1992, the yearly usage (in weight of 
material applied) of ink, coating, thinner, clean-up material, and other 
VOC-containing material, shall not exceed the applicable pounds per year 
limit established below. The yearly weight of ink, coating, thinner, 
clean-up material, and other VOC-containing material is to be calculated 
according to the procedure in paragraph (x)(14)(ii) of this section.

------------------------------------------------------------------------
                                                                 Weight
                      Material                          Usage    Percent
                                                      (lbs/yr)     VOC
------------------------------------------------------------------------
#6 ink..............................................     9,076      56.8
#7 ink..............................................     1,278      54.2
#2 ink..............................................     2,911      72.7
Blue N.C. lacq......................................       394      64.3
Black M lacq........................................       753      61.6
4B9L Clear..........................................     2,451      77.1
4B9L H Clear........................................     3,360      75.0
Flow-Out Agent......................................     1,795      97.1
D.S. Stamp lacq.....................................     1,047      62.0
Dull write-on.......................................        86      71.6
AH-16...............................................       621      84.5
Thinner (#7,6)......................................     2,350     100.0
Exon 470............................................     1,668      65.4
9L Clear............................................     2,451      77.1
White M lacq........................................     3,467      47.0
Tedlar Gr. Vehicle..................................     1,050      66.7
TH-98...............................................    22,047      73.2
TH-57...............................................        59      69.5
TH-14M..............................................    16,520       0.7
PS 160..............................................    10,644       3.0
#1 tint.............................................     4,872      69.3
#2 tint.............................................     4,256      83.7
Roto Color..........................................    13,884      62.0
1st SS White........................................    25,740      51.5
2nd SS White........................................    25,740      51.5
Clean Up............................................   108,742     100.0
Other Materials.....................................       400     100.0
------------------------------------------------------------------------

    (ii) The yearly weight of material used is to be calculated as 
follows:
    (A) Compute the weight of each ink, coating, thinner, clean-up 
material,

[[Page 407]]

and other VOC-containing material used each month by the 15th of the 
following month.
    (B) By the 15th of each month, add the monthly usage (in pounds) for 
each ink, coating, thinner, clean-up material, and other VOC-containing 
material for the twelve previous months (to obtain the yearly weight of 
each ink, coating, thinner, clean-up material used). A comparison of 
these yearly usage levels (in pounds) with purchase records must be made 
to ensure the accuracy of the monthly usage levels (in pounds) obtained 
to satisfy paragraph (x)(14)(ii)(A) of this section.
    (iii) Beginning on August 1, 1992, the owner and operator of the 
American Decal and Manufacturing Company plant in Chicago, Illinois, 
shall keep the following records for each ink, coating, thinner, clean-
up material, and other VOC-containing material for each month. All 
records shall be kept by the American Decal and Manufacturing Company 
for 3 years and shall be made available to the Administrator on request:
    (A) The name and identification number of each ink, coating, 
thinner, clean-up material, and other VOC-containing material as applied 
or used.
    (B) The weight percent VOC of each ink, coating, thinner, clean-up 
material, and each other VOC-containing material as applied or used each 
month.
    (C) The as applied weight of each ink, coating, thinner, clean-up 
material, and other VOC-containing material used each month.
    (iv) Any record showing a violation of paragraph (x)(14)(i) of this 
section after October 20, 1995 shall be reported by sending a copy of 
such record to the Administrator within 30 days of the violation.
    (v) To determine compliance with paragraph (x)(14)(i) of this 
section and to establish the records required under paragraph 
(x)(14)(iii) of this section, the weight percent VOC of each ink, 
coating, thinner, clean-up material, and other VOC-containing material 
shall be determined by the applicable test methods and procedures 
specified in paragraph (a)(4) of this section. Any material reported to 
be 100 percent VOC does not have to be tested for weight percent VOC.
    (y) Recordkeeping and reporting for non-CTG sources--(1) Exempt 
emission sources. Upon request by the Administrator, the owner or 
operator of an emission source which is exempt from the requirements of 
paragraphs (u), (v), (w), (x), or (e)(3)(ii) of this section shall 
submit records to the Administrator within 30 calendar days from the 
date of the request that document that the emission source is exempt 
from those requirements.
    (2) Subject emission sources. (i) Any owner or operator of a VOM 
emission source which is subject to the requirements of paragraph (u), 
(v), (w) or (x) of this section and complying by the use of emission 
capture and control equipment shall comply with the following:
    (A) By July 1, 1991, or upon initial start-up of a new emission 
source, the owner or operator of the subject VOM emission source shall 
perform all tests and submit to the Administrator the results of all 
tests and calculations necessary to demonstrate that the subject 
emission source will be in compliance on and after July 1, 1991, or on 
and after the initial start-up date.
    (B) On and after July 1, 1991, or on and after the initial start-up 
date, the owner or operator of a subject VOM emission source shall 
collect and record all of the following information each day and 
maintain the information at the facility for a period of three years:
    (1) Control device monitoring data.
    (2) A log of operating time for the capture system, control device, 
monitoring equipment and the associated emission source.
    (3) A maintenance log for the capture system, control device and 
monitoring equipment detailing all routine and non-routine maintenance 
performed including dates and duration of any outages.
    (C) On and after July 1, 1991, the owner or operator of a subject 
VOM emission source shall notify the Administrator in the following 
instances:
    (1) Any record showing a violation of the requirements of paragraphs 
(u), (v), (w), or (x) of this section shall be reported by sending a 
copy of such record to the Administrator within 30 days

[[Page 408]]

following the occurrence of the violation.
    (2) At least 30 calendar days before changing the method of 
compliance with paragraphs (u) or (x) of this section from the use of 
capture systems and control devices to the use of complying coatings, 
the owner or operator shall comply with all requirements of paragraph 
(y)(2)(ii)(A) of this section. Upon changing the method of compliance 
with paragraphs (u) or (x) of this section from the use of capture 
systems and control devices to the use of complying coatings, the owner 
or operator shall comply with all requirements of paragraph (y)(2)(ii) 
of this section.
    (ii) Any owner or operator of a coating line which is subject to the 
requirements of paragraphs (u) or (x) of this section and complying by 
means of the daily-weighted average VOM content limitation shall comply 
with the following:
    (A) By July 1, 1991, or upon initial start-up of a coating line 
subject to paragraph (u) or (x) of this section; the owner or operator 
of the subject coating line shall certify to the Administrator that the 
coating line will be in compliance on and after July 1, 1991, or on and 
after the initial start-up date. Such certification shall include:
    (1) The name and identification number of each coating line which 
will comply by means of the daily-weighted average VOM content 
limitation.
    (2) The name and identification number of each coating as applied on 
each coating line.
    (3) The weight of VOM per volume and the volume of each coating 
(minus water and any compounds which are specifically exempted from the 
definition of VOM) as applied each day on each coating line.
    (4) The instrument or method by which the owner or operator will 
accurately measure or calculate the volume of each coating as applied 
each day on each coating line.
    (5) The method by which the owner or operator will create and 
maintain records each day as required in paragraph (y)(2)(ii)(B) of this 
section.
    (6) An example of the format in which the records required in 
paragraph (y)(2)(ii)(B) of this section will be kept.
    (B) On and after July 1, 1991, or on and after the initial start-up 
date, the owner or operator of a subject coating line shall collect and 
record all of the following information each day for each coating line 
and maintain the information at the facility for a period of three 
years:
    (1) The name and identification number of each coating as applied on 
each coating line.
    (2) The weight of VOM per volume and the volume of each coating 
(minus water and any compounds which are specifically exempted from the 
definition of VOM) as applied each day on each coating line.
    (3) The daily-weighted average VOM content of all coatings as 
applied on each coating line as defined in paragraph (a)(3) of this 
section.
    (C) On and after July 1, 1991, the owner or operator of a subject 
coating line shall notify the Administrator in the following instances:
    (1) Any record showing violation of the requirements of paragraph 
(u) or (x) of this section shall be reported by sending a copy of such 
record to the Administrator within 30 days following the occurrence of 
the violation.
    (2) At least 30 calendar days before changing the method of 
compliance with paragraph (u) or (x) of this section from the use of 
complying coatings to the use capture systems and control devices, the 
owner or operator shall comply with all requirements of paragraph 
(y)(2)(i)(A) of this section. Upon changing the method of compliance 
with paragraphs (u) or (x) of this section from the use of complying 
coatings to the use capture systems and control devices, the owner or 
operator shall comply with all requirements of paragraph (y)(2)(i) of 
this section.
    (iii) Any owner or operator of a VOM emission source which is 
subject to the requirements of paragraphs (u), (v), (w) or (x) of this 
section and complying by means of an alternative control plan which has 
been approved by the Administrator as a SIP or FIP revision shall comply 
with the recordkeeping and reporting requirements specified in the 
altenative control plan.

[[Page 409]]

    (z) Rules stayed. Not withstanding any other provision of this 
subpart, the effectiveness of the following rules is stayed as indicated 
below.
    (1) [Reserved]
    (2) Compliance with all of 40 CFR 52.741 is stayed for 60 days (July 
1, 1991, until August 30, 1991) as it pertains to the following parties: 
The Illinois Environmental Regulatory Group including its approximately 
40 member firms; Allsteel, Incorporated; Riverside Laboratories, 
Incorporated; the Printing Industry of Illinois/Indiana Association 
including its member firms, and R.R. Donnelley & Sons Company; the rules 
applicable to General Motors Corporation; Reynolds Metals Company; 
Stepan Company; and Duo-Fast Corporation. Final compliance for these 
parties is extended 60 days from July 1, 1991 until August 30, 1991.
    (3) The following rules are stayed from July 23, 1991, until USEPA 
completes its reconsideration as indicated:
    (i) 40 CFR 52.741(e) only as it applies to Duo-Fast Corporation's 
Franklin Park, Illinois ``power-driven metal fastener'' manufacturing 
facility, and
    (ii) 40 CFR 52.741 (w) and (y) only as it applies to Stepan 
Company's miscellaneous organic chemical manufacturing processes at its 
manufacturing facility located near Millsdale, Illinois.
    When USEPA concludes its reconsideration, it will publish its 
decision and any actions required to effectuate that decision in the 
Federal Register.
    (4)-(5)  [Reserved]

 Appendix A--List of Chemicals Defining Synthetic Organic Chemical and 
                          Polymer Manufacturing

------------------------------------------------------------------------
              OCPDB No.\1\                           Chemical
------------------------------------------------------------------------
20.....................................  Acetal.
30.....................................  Acetaldehyde.
40.....................................  Acetaldol.
50.....................................  Acetamide.
65.....................................  Acetanilide.
70.....................................  Acetic acid.
80.....................................  Acetic anhydride.
90.....................................  Acetone.
100....................................  Acetone cyanohydrin.
110....................................  Acetonitrile.
120....................................  Acetophenone.
125....................................  Acetyl chloride.
130....................................  Acetylene.
140....................................  Acrolein.
150....................................  Acrylamide.
160....................................  Acrylic acid & esters.
170....................................  Acrylonitrile.
180....................................  Adipic acid.
185....................................  Adiponitrile.
190....................................  Alkyl naphthalenes.
200....................................  Allyl alcohol.
210....................................  Allyl chloride.
220....................................  Aminobenzoic acid.
230....................................  Aminoethylethanolamine.
235....................................  p-aminophenol.
240....................................  Amyl acetates.
250....................................  Amyl alcohols.
260....................................  Amyl amine.
270....................................  Amyl chloride.
280....................................  Amyl mercaptans.
290....................................  Amyl phenol.
300....................................  Aniline.
310....................................  Aniline hydrochloride.
320....................................  Anisidine.
330....................................  Anisole.
340....................................  Anthranilic acid.
350....................................  Anthraquinone.
360....................................  Benzaldehyde.
370....................................  Benzamide.
380....................................  Benzene.
390....................................  Benzenedisulfonic acid.
400....................................  Benzene-sulfonic acid.
410....................................  Benzil.
420....................................  Benzilic acid.
430....................................  Benzoic acid.
440....................................  Benzoin.
450....................................  Bennzonitrile.
460....................................  Benzophenone.
480....................................  Benzotrichloride.
490....................................  Benzoyl chloride.
500....................................  Benzyl chalcohol.
510....................................  Benzyl amine.
520....................................  Benzyl benzoate.
530....................................  Benzyl chloride.
540....................................  Benzyl dichloride.
550....................................  Biphenyl.
560....................................  Bisphenol A.
570....................................  Bromobenzene.
580....................................  Bromonaphthalene.
590....................................  Butadiene.
592....................................  1-butene.
600....................................  n-butyl acetate.
630....................................  n-butyl acrylate.
640....................................  n-butyl alcohol.
650....................................  s-butyl alcohol.
660....................................  t-butyl alcohol.
670....................................  n-butylamine.
680....................................  s-butylamine.
690....................................  t-butylamine.
700....................................  p-pert-butyl benzoic acid.
750....................................  n-butyraldehyde.
760....................................  Butyric acid.
770....................................  Butyric anhydride.
780....................................  Butyronitrile.
785....................................  Caprolactam.
790....................................  Carbon disulfide.
800....................................  Carbon tetrabromide.
810....................................  Carbon tetrachloride.
820....................................  Cellulose acetate.
840....................................  Chloroacetic acid.
850....................................  m-chloroaniline.
860....................................  o-chloroaniline.
870....................................  p-chloroaniline.
880....................................  Chlorobenzaldehyde.
890....................................  Chlorobenzene.
900....................................  Chlorobenzoic acid.
905....................................  Chlorobenzotrichloride.
910....................................  Chlorobenzoyl chloride.
920....................................  Chlorodifluoroethane.
921....................................  Chlorodifluoromethane.
930....................................  Chloroform

[[Page 410]]

940....................................  Chloronaphthalene.
950....................................  o-chloronitrobenzene.
951....................................  p-chloronitrobenzene.
960....................................  Chlorophenols.
964....................................  Chloroprene.
965....................................  Chlorosulfonic acid.
970....................................  m-chlorotoluene.
980....................................  o-chlorotoluene.
990....................................  p-chlorotoluene.
992....................................  Chlorotrifluoromethane.
1000...................................  m-cresol.
1010...................................  o-cresol.
1020...................................  p-cresol.
1021...................................  Mixed cresols.
1030...................................  Cresylic acid.
1040...................................  Crontonaldehyde.
1050...................................  Crontonic acid.
1060...................................  Cumene.
1070...................................  Cumene hydroperoxide.
1080...................................  Cyanoacetic acid.
1090...................................  Cyanogen chloride.
1100...................................  Cyanuric acid.
1110...................................  Cyanuric chloride.
1120...................................  Cychohexane.
1130...................................  Cyclohexanol.
1140...................................  Cyclohexanone.
1150...................................  Cyclohexene.
1160...................................  Cyclohexylamine.
1170...................................  Cyclooctadiene.
1180...................................  Decanol.
1190...................................  Diacetone alcohol.
1200...................................  Diaminobenzoic acid.
1210...................................  Dichloroaniline.
1215...................................  m-dichlorobenzene.
1216...................................  o-dichlorobenzene.
1220...................................  p-dichlorobenzene.
1221...................................  Dichlorodifluoromethane.
1240...................................  Dichloroethyl ether 1,2-
                                          dichloroethane.
1250...................................  Dichlorohydrin
1270...................................  Dichloropropene.
1280...................................  Dicyclohexylamine.
1290...................................  Diethylamine.
1300...................................  Diethylene glycol.
1304...................................  Diethylene glycol diethyl
                                          ether.
1305...................................  Diethylene glycol dimethyl
                                          ether.
1310...................................  Diethylene glycolmonobutyl
                                          ether.
1320...................................  Diethylene glycolmonobutyl
                                          ether acetate.
1330...................................  Diethylene glycolmonoethyl
                                          ether.
1340...................................  Diethylene glycolmonoethyl
                                          ether acetate.
1360...................................  Diethylene glycolmonomethyl
                                          ether.
1420...................................  Diethyl sulfate.
1430...................................  Difluoroethane.
1440...................................  Diisobutylene.
1442...................................  Diisodecyl phthalate.
1444...................................  Diisooctyl phthalate.
1450...................................  Diketene.
1460...................................  Dimethylamine.
1470...................................  N,N-dimethylaniline.
1480...................................  N,N-dimethylether.
1490...................................  N,N-dimethylformamide.
1495...................................  Dimethylhydrazine.
1500...................................  Dimethyl sulfate.
1510...................................  Dimethyl sulfide.
1520...................................  Dimethylsulfoxide.
1530...................................  Dimethylterephthalate.
1540...................................  3,5-dinitrobenzoic acid.
1545...................................  Dinitrophenol.
1560...................................  Dioxane.
1570...................................  Dioxolane.
1580...................................  Diphenylamine.
1590...................................  Diphenyl oxide.
1600...................................  Diphenyl thiourea.
1610...................................  Dipropylene glycol.
1620...................................  Dodecene.
1630...................................  Dodecylaniline.
1640...................................  Dodecylphenol.
1650...................................  Epichlorohydrin.
1660...................................  Ethanol.
1661...................................  Ethanolamines.
1670...................................  Ethyl acetate.
1680...................................  Ethyl acetoacetate.
1690...................................  Ethyl acrylate.
1700...................................  Ethylamine.
1710...................................  Ethylbenzene.
1720...................................  Ethyl bromide.
1730...................................  Ethylcellulose.
1740...................................  Ethyl chloride.
1750...................................  Ethyl chloroacetate.
1760...................................  Ethylcyanoacetate.
1770...................................  Ethylene.
1780...................................  Ethylene carbonate.
1790...................................  Ethylene chlorodhydrin.
1800...................................  Ethylenediamine.
1810...................................  Ethylene dibromide.
1830...................................  Ethylene glycol.
1840...................................  Ethylene glycol diacetate.
1870...................................  Ethylene glycol dimethyl ether.
1890...................................  Ethylene glycol monobutyl
                                          ether.
1900...................................  Ethylene glycol monobutyl ether
                                          acetate.
1910...................................  Ethylene glycol monoethyl
                                          ether.
1920...................................  Ethylene glycol monoethyl ether
                                          acetate.
1930...................................  Ethylene glycol monoethyl
                                          ether.
1940...................................  Ethylene glycol monomethyl
                                          ether acetate.
1960...................................  Ethylene glycol monophenyl
                                          ether.
1970...................................  Ethylene glycol monopropyl
                                          ether.
1980...................................  Ethylene oxide.
1990...................................  Ethyl ether.
2000...................................  2-ethylhexanol.
2010...................................  Ethyl orthoformate.
2020...................................  Ethyl oxalate.
2030...................................  Ethyl sodium oxalacetate.
2040...................................  Formaldehyde.
2050...................................  Formamide.
2060...................................  Formic acid.
2070...................................  Fumaric acid.
2073...................................  Furfural.
2090...................................  Glycerol (Synthetic).
2091...................................  Glycerol dichlorohydrin.
2100...................................  Glycerol triether.
2110...................................  Glycine.
2120...................................  Glyoxal.
2145...................................  Hexachlorobenzene.
2150...................................  Hexachloroethane.
2160...................................  Hexadecyl alcohol.
2165...................................  Hexamethylenediamine.
2170...................................  Hexamethylene glycol.
2180...................................  Hexamethylentetramine.
2190...................................  Hydrogen cyanide.
2200...................................  Hydroquinone.
2210...................................  p-hydroxy-benzoic acid.
2240...................................  Isoamylene.
2250...................................  Isobutanol.
2260...................................  Isobutyl acetate.
2261...................................  Isobutylene.
2270...................................  Isobutyraldehyde.
2280...................................  Isobutyric acid.
2300...................................  Isodecanol.
2320...................................  Isooctyl alcohol.
2321...................................  Isopentane.
2330...................................  Isophorone.
2340...................................  Isophthalic acid.
2350...................................  Isoprene.
2360...................................  Isopropanol.
2370...................................  Isopropyl acetate.
2380...................................  Isopropylamine.
2390...................................  Isopropyl chloride.

[[Page 411]]

2400...................................  Isopropylphenol.
2410...................................  Ketene.
2414...................................  Linear alkylsulfonate.
2417...................................  Linear alkylbenzene.
2420...................................  Maleic acid.
2430...................................  Maleic anhydride.
2440...................................  Malic acid.
2450...................................  Mesityl oxide.
2455...................................  Metanilic acid.
2460...................................  Methacrylic acid.
2490...................................  Methallyl chloride.
2500...................................  Methanol.
2510...................................  Methyl acetate.
2520...................................  Methyl acetoacetate.
2530...................................  Methylamine.
2540...................................  n-methylaniline.
2545...................................  Methyl bromide.
2550...................................  Methyl butynol.
2560...................................  Methyl chloride.
2570...................................  Methyl cyclohexane.
2590...................................  Methyl cyclohexanone.
2620...................................  Methylene chloride.
2630...................................  Methylene dianiline.
2635...................................  Methylene diphenyl
                                          diisocyanate.
2640...................................  Methyl ethyl ketone.
2644...................................  Methyl formate.
2650...................................  Methyl isobutyl carbinol.
2660...................................  Methyl isobutyl ketone.
2665...................................  Methyl methacrylate.
2670...................................  Methyl pentynol.
2690...................................  a-methyl styrene.
2700...................................  Morpholine.
2710...................................  a-napthalene sulfonic acid.
2720...................................  B-napthalene sulfonic acid.
2730...................................  a-naphthol.
2740...................................  B-naphthol.
2750...................................  Neopentanoic acid.
2756...................................  o-nitroaniline.
2757...................................  p-nitroaniline.
2760...................................  o-nitroanisole.
2762...................................  p-nitroanisole.
2770...................................  Nitrobenzene.
2780...................................  Nitrobenzoic acid (o, m & p).
2790...................................  Nitroethane.
2791...................................  Nitromethane.
2792...................................  Nitrophenol.
2795...................................  Nitropropane.
2800...................................  Nitrotoluene.
2810...................................  Nonene.
2820...................................  Nonyl phenol.
2830...................................  Octyl phenol.
2840...................................  Paraldehyde.
2850...................................  Pentaerythritol.
2851...................................  n-pentane.
2855...................................  l-pentene.
2860...................................  Perchloroethylene.
2882...................................  Perchloromethylmercaptan.
2890...................................  o-phenetidine.
2900...................................  p-phenetidine.
2910...................................  Phenol.
2920...................................  Phenolsulfonic acids.
2930...................................  Phenyl anthranilic acid.
2940...................................  Phenylenediamine.
2960...................................  Phthalic anhydride.
2970...................................  Phthalimide.
2973...................................  b-picoline.
2976...................................  Piperazine.
3000...................................  Polybutenes.
3010...................................  Polyethylene glycol.
3025...................................  Polypropylene glycol.
3063...................................  Propionaldehyde.
3066...................................  Propionic acid.
3070...................................  n-propyl alcohol.
3075...................................  Propylamine.
3080...................................  Propyl chloride.
3090...................................  Propylene.
3100...................................  Propylene chlorohydrin.
3110...................................  Propylene dichloride.
3111...................................  Propylene glycol.
3120...................................  Propylene oxide.
3130...................................  Pyridine.
3140...................................  Quinone.
3150...................................  Resorcinol.
3160...................................  Resorcylic acid.
3170...................................  Salicylic acid.
3180...................................  Sodium acetate.
3181...................................  Sodium benzoate.
3190...................................  Sodium carboxymethylcellulose.
3191...................................  Sodium chloroacetate.
3200...................................  Sodium formate.
3210...................................  Sodium phenate.
3220...................................  Sorbic acid.
3230...................................  Styrene.
3240...................................  Succinic acid.
3250...................................  Succinitrile.
3251...................................  Sulfanilic acid.
3260...................................  Sulfolane.
3270...................................  Tannic acid.
3280...................................  Terephthalic acid.
3290 & 3291............................  Tetrachloroethanes.
3300...................................  Tetrachlorophthalic anhydride.
3310...................................  Tetraethyllead.
3320...................................  Tetrahydronaphthalene.
3330...................................  Tetrahydrophthalic anhydride.
3335...................................  Tetramethyllead.
3340...................................  Tetramethylenediamine.
3341...................................  Tetramethylethylenediamine.
3349...................................  Toluene.
3350...................................  Toluene-2,4-diamine.
3354...................................  Toluene-2,4-diisocyanate.
3355...................................  Toluene diisocyanates
                                          (mixture).
3360...................................  Toluene sulfonamide.
3370...................................  Toluene sulfonic acids.
3380...................................  Toluene sulfonylchloride.
3381...................................  Toluidines.
3393...................................  Trichlorobenzenes.
3395...................................  1,1,1-trichloroethane.
3400...................................  1,1,2-trichloroethane.
3410...................................  Trichloroethylene.
3411...................................  Trichlorofluoromethane.
3420...................................  1,2,3-trichloropropane.
3430...................................  1,1,2-trichloro-1,2,2-
                                          trifluoroethane.
3450...................................  Triethylamine.
3460...................................  Triethylene glycol.
3470...................................  Triethylene glycoldimethyl
                                          ether.
3480...................................  Triisobutylene.
3490...................................  Trimethylamine.
3510...................................  Vinyl acetate.
3520...................................  Vinyl chloride.
3530...................................  Vinylidene chloride.
3540...................................  Vinyl toluene.
3541...................................  Xylene (mixed).
3560...................................  o-xylene.
3570...................................  p-xylene.
3580...................................  Xylenol.
3590...................................  Xylidine, 1,3-butylene glycol,
                                          Dinitrotoluene,
                                          Methyltertbutyl ether,
                                          Phosgene, Polyethylene,
                                          Polypropylene, Polystyrene,
                                          Urea.
------------------------------------------------------------------------
\1\ The OCPDB Numbers are reference indices assigned to the various
  chemicals in the Organic Chemical Producers Data Base developed by the
  USEPA.


[[Page 412]]

      Appendix B--VOM Measurement Techniques for Capture Efficiency

                  Procedure G.1--Captured VOC Emissions

                             1. Introduction

    1.1  Applicability. This procedure is applicable for determining the 
volatile organic compounds (VOC) content of captured gas streams. It is 
intended to be used as a segment in the development of liquid/gas or 
gas/gas protocols for determining VOC capture efficiency (CE) for 
surface coating and printing operations. The procedure may not be 
acceptable in certain site-specific situations, e.g., when: (1) Direct 
fired heaters or other circumstances affect the quantity of VOC at the 
control device inlet; and (2) particulate organic aerosols are formed in 
the process and are present in the captured emissions.
    1.2  Principle. The amount of VOC captured (G) is calculated as the 
sum of the products of the VOC content (CGj), the flow rate 
(QGj), and the sample time (TC) from each captured 
emissions point.
    1.3  Estimated measurement uncertainty. The measurement 
uncertainties are estimated for each captured or fugitive emissions 
point as follows: QGj=5.5 percent and 
CGj=5.0 percent. Based on these numbers, the 
probable uncertainty for G is estimated at about 7.4 
percent.
    1.4  Sampling requirements. A capture efficiency test shall consist 
of at least three sampling runs. The sampling time for each run should 
be at least 8 hours, unless otherwise approved.
    1.5  Notes. Because this procedure is often applied in highly 
explosive areas, caution and care should be exercised in choosing 
appropriate equipment and installing and using the equipment. Mention of 
trade names or company products does not constitute endorsement. All gas 
concentrations (percent, ppm) are by volume, unless otherwise noted.

                        2. Apparatus and Reagents

    2.1  Gas VOC concentration. A schematic of the measurement system is 
shown in Figure 1. The main components are described below:
    2.1.1  Sample probe. Stainless steel, or equivalent. The probe shall 
be heated to prevent VOC condensation.
    2.1.2  Calibration valve assembly. Three-way valve assembly at the 
outlet of sample probe to direct the zero and calibration gases to the 
analyzer. Other methods, such as quick-connect lines, to route 
calibration gases to the outlet of the sample probe are acceptable.
    2.1.3  Sample line. Stainless steel or Teflon tubing to transport 
the sample gas to the analyzer. The sample line must be heated to 
prevent condensation.
    2.1.4  Sample pump. A lead-free pump, to pull the sample gas through 
the system at a flow rate sufficient to minimize the response time of 
the measurement system. The components of the pump that contact the gas 
stream shall be constructed of stainless steel or Teflon. The sample 
pump must be heated to prevent condensation.
    2.1.5  Sample flow rate control. A sample flow rate control valve 
and rotameter, or equivalent, to maintain a constant sampling rate 
within 10 percent. The flow rate control valve and rotameter must be 
heated to prevent condensation. A control valve may also be located on 
the sample pump bypass loop to assist in controlling the sample pressure 
and flow rate.
    2.1.6  Sample gas manifold. Capable of diverting a portion of the 
sample gas stream to the flame ionization analyzer (FIA), and the 
remainder to the bypass discharge vent. The manifold components shall be 
constructed of stainless steel or Teflon. If captured or fugitive 
emissions are to be measured at multiple locations, the measurement 
system shall be designed to use separate sampling probes, lines, and 
pumps for each measurement location and a common sample gas manifold and 
FIA. The sample gas manifold and connecting lines to the FIA must be 
heated to prevent condensation.
    2.1.7  Organic concentration analyzer. An FIA with a span value of 
1.5 times the expected concentration as propane; however, other span 
values may be used if it can be demonstrated that they would provide 
more accurate measurements.
    The system shall be capable of meeting or exceeding the following 
specifications:
    2.1.7.1  Zero drift. Less than 3.0 percent of the span 
value.
    2.1.7.2  Calibration drift. Less than 3.0 percent of the 
span value.
    2.1.7.3  Calibration error. Less than 5.0 percent of the 
calibration gas value.
    2.1.7.4  Response time. Less than 30 seconds.
    2.1.8  Integrator/data acquisition system. An analog or digital 
device or computerized data acquisition system used to integrate the FIA 
response or compute the average response and record measurement data. 
The minimum data sampling frequency for computing average or integrated 
values is one measurement value every 5 seconds. The device shall be 
capable of recording average values at least once per minute.
    2.1.9  Calibration and other gases. Gases used for calibration, 
fuel, and combustion air (if required) are contained in compressed gas 
cylinders. All calibration gases shall be traceable to NIST standards 
and shall be certified by the manufacturer to 1 percent of 
the tag value. Additionally, the manufacturer of the cylinder should 
provide a recommended shelf life for each calibration gas cylinder over 
which the concentration does not change more than 2 percent 
from the

[[Page 413]]

certified value. For calibration gas values not generally available, 
alternative methods for preparing calibration gas mixtures, such as 
dilution systems, may be used with prior approval.
    2.1.9.1  Fuel. A 40 percent H2/60 percent He or 40 
percent H2/60 percent N2 gas mixture is 
recommended to avoid an oxygen synergism effect that reportedly occurs 
when oxygen concentration varies significantly from a mean value.
    2.1.9.2  Carrier gas. High purity air with less than 1 ppm of 
organic material (as propane or carbon equivalent) or less than 0.1 
percent of the span value, whichever is greater.
    2.1.9.3  FIA Linearity calibration gases. Low-, mid-, and high-range 
gas mixture standards with nominal propane concentrations of 20-30, 45-
55, and 70-80 percent of the span value in air, respectively. Other 
calibration values and other span values may be used if it can be shown 
that more accurate measurements would be achieved.
    2.1.10  Particulate filter. An in-stack or an out-of-stack glass 
fiber filter is recommended if exhaust gas particulate loading is 
significant. An out-of-stack filter must be heated to prevent any 
condensation unless it can be demonstrated that no condensation occurs.
    2.2  Captured emissions volumetric flow rate.
    2.2.1  Method 2 or 2A apparatus. For determining volumetric flow 
rate.
    2.2.2  Method 3 apparatus and reagents. For determining molecular 
weight of the gas stream. An estimate of the molecular weight of the gas 
stream may be used if it can be justified.
    2.2.3  Method 4 apparatus and reagents. For determining moisture 
content, if necessary.

     3. Determinations of Volumetric Flow Rate of Captured Emissions

    3.1  Locate all points where emissions are captured from the 
affected facility. Using Method 1, determine the sampling points. Be 
sure to check each site for cyclonic or swirling flow.
    3.2  Measure the velocity at each sampling site at least once every 
hour during each sampling run using Method 2 or 2A.

         4. Determinations of VOC Content of Captured Emissions

    4.1  Analysis duration. Measure the VOC responses at each captured 
emissions point during the entire test run or, if applicable, while the 
process is operating. If there are multiple captured emission locations, 
design a sampling system to allow a single FIA to be used to determine 
the VOC responses at all sampling locations.
    4.2  Gas VOC concentration.
    4.2.1  Assemble the sample train as shown in Figure 1. Calibrate the 
FIA according to the procedure in section 5.1.
    4.2.2  Conduct a system check according to the procedure in section 
5.3.
    4.2.3  Install the sample probe so that the probe is centrally 
located in the stack, pipe, or duct, and is sealed tightly at the stack 
port connection.
    4.2.4  Inject zero gas at the calibration valve assembly. Allow the 
measurement system response to reach zero. Measure the system response 
time as the time required for the system to reach the effluent 
concentration after the calibration valve has been returned to the 
effluent sampling position.
    4.2.5  Conduct a system check before and a system check after each 
sampling run according to the procedures in sections 5.2 and 5.3. If the 
drift check following a run indicates unacceptable performance, the run 
is not valid. The tester may elect to perform system drift checks during 
the run not to exceed one drift check per hour.
    4.2.6  Verify that the sample lines, filter, and pump temperatures 
are 1205 deg.C.
    4.2.7  Begin sampling at the start of the test period and continue 
to sample during the entire run. Record the starting and ending times 
and any required process information as appropriate. If multiple 
captured emission locations are sampled using a single FIA, sample at 
each location for the same amount of time (e.g., 2 minutes) and continue 
to switch from one location to another for the entire test run. Be sure 
that total sampling time at each location is the same at the end of the 
test run. Collect at least 4 separate measurements from each sample 
point during each hour of testing. Disregard the measurements at each 
sampling location until two times the response time of the measurement 
system has elapsed. Continue sampling for at least 1 minute and record 
the concentration measurements.
    4.3  Background concentration.
    4.3.1  Locate all NDO's of the TTE. A sampling point shall be 
centrally located outside of the TTE at 4 equivalent diameters from each 
NDO, if possible. If there are more than 6 NDO's, choose 6 sampling 
points evenly spaced among the NDO's.
    4.3.2  Assemble the sample train as shown in Figure 2. Calibrate the 
FIA and conduct a system check according to the procedures in sections 
5.1 and 5.3.


    Note: This sample train shall be a separate sampling train from the 
one to measure the captured emissions.


    4.3.3  Position the probe at the sampling location.
    4.3.4  Determine the response time, conduct the system check and 
sample according to the procedures described in sections 4.2.4 to 4.2.7.

[[Page 414]]

    4.4  Alternative procedure. The direct interface sampling and 
analysis procedure described in section 7.2 of Method 18 may be used to 
determine the gas VOC concentration. The system must be designed to 
collect and analyze at least one sample every 10 minutes.

                  5. Calibration and Quality Assurance

    5.1 FIA  calibration and linearity check. Make necessary adjustments 
to the air and fuel supplies for the FIA and ignite the burner. Allow 
the FIA to warm up for the period recommended by the manufacturer. 
Inject a calibration gas into the measurement system and adjust the 
back-pressure regulator to the value required to achieve the flow rates 
specified by the manufacturer. Inject the zero- and the high-range 
calibration gases and adjust the analyzer calibration to provide the 
proper responses. Inject the low- and mid-range gases and record the 
responses of the measurement system. The calibration and linearity of 
the system are acceptable if the responses for all four gases are within 
5 percent of the respective gas values. If the performance of the system 
is not acceptable, repair or adjust the system and repeat the linearity 
check. Conduct a calibration and linearity check after assembling the 
analysis system and after a major change is made to the system.
    5.2  Systems drift checks. Select the calibration gas that most 
closely approximates the concentration of the captured emissions for 
conducting the drift checks. Introduce the zero and calibration gas at 
the calibration valve assembly and verify that the appropriate gas flow 
rate and pressure are present at the FIA. Record the measurement system 
responses to the zero and calibration gases. The performance of the 
system is acceptable if the difference between the drift check 
measurement and the value obtained in section 5.1 is less than 3 percent 
of the span value. Conduct the system drift checks at the end of each 
run.
    5.3  System check. Inject the high range calibration gas at the 
inlet to the sampling probe while the dilution air is turned off. Record 
the response. The performance of the system is acceptable if the 
measurement system response is within 5 percent of the value obtained in 
section 5.1 for the high range calibration gas. Conduct a system check 
before and after each test run.
    5.4  Analysis audit. Immediately before each test analyze an audit 
cylinder as described in section 5.2. The analysis audit must agree with 
the audit cylinder concentration within 10 percent.

                             6. Nomenclature

Ai=area of NDO i, ft2.
AN=total area of all NDO's in the enclosure, ft2.
CBi=corrected average VOC concentration of background 
          emissions at point i, ppm propane.
CB=average background concentration, ppm propane.
CGj=corrected average VOC concentration of captured emissions 
          at point j, ppm propane.
CDH=average measured concentration for the drift check 
          calibration gas, ppm propane.
CDO=average system drift check concentration for zero 
          concentration gas, ppm propane.
CH=actual concentration of the drift check calibration gas, 
          ppm propane.
Ci=uncorrected average background VOC concentration measured 
          at point i, ppm propane.
Cj=uncorrected average VOC concentration measured at point j, 
          ppm propane.
G=total VOC content of captured emissions, kg.
K1=1.830 x 10-6 kg/ (m3-ppm).
n=number of measurement points.
QGj=average effluent volumetric flow rate corrected to 
          standard conditions at captured emissions point j, 
          m3/min.
TC=total duration of captured emissions sampling run, min.

                             7. Calculations

    7.1  Total VOC captured emissions.
    [GRAPHIC] [TIFF OMITTED] TC07NO91.012
    
    7.2 VOC concentration of the captured emissions at point j.
    [GRAPHIC] [TIFF OMITTED] TC07NO91.013
    
    7.3. Background VOC concentration at point i.
    [GRAPHIC] [TIFF OMITTED] TC07NO91.014
    
    7.4 Average background concentration.
    [GRAPHIC] [TIFF OMITTED] TC07NO91.015
    

    Note: If the concentration at each point is with in 20 percent of 
the average concentration of all points, the terms ``Ai'' and 
``AN'' may be deleted from Equation 4.


[[Page 415]]



       Procedure G.2--Captured VOC Emissions (Dilution Technique)

                             1. Introduction

    1.1  Applicability. This procedure is applicable for determining the 
volatile organic compounds (VOC) content of captured gas streams. It is 
intended to be used as a segment in the development of a gas/gas 
protocol in which fugitive emissions are measured for determining VOC 
capture efficiency (CE) for surface coating and printing operations. A 
dilution system is used to reduce the VOC concentration of the captured 
emission to about the same concentration as the fugitive emission. The 
procedure may not be acceptable in certain site-specific situations, 
e.g., when: (1) Direct fired heaters or other circumstances affect the 
quantity of VOC at the control device inlet; and (2) particulate organic 
aerosols are formed in the process and are present in the captured 
emissions.
    1.2  Principle. The amount of VOC captured (G) is calculated as the 
sum of the products of the VOC content (CGj), the flow rate 
(QGj), and the sampling time (TC) from each 
captured emissions point.
    1.3  Estimated measurement uncertainty. The measurement 
uncertainties are estimated for each captured or fugitive emissions 
point as follows: OGj=5.5 percent and 
CGj=5 percent. Based on these numbers, the 
probable uncertainty for G is estimated at about 7.4 
percent.
    1.4  Sampling requirements. A capture efficiency test shall consist 
of at least three sampling runs. The sampling time for each run should 
be at least 8 hours, unless otherwise approved.
    1.5  Notes. Because this procedure is often applied in highly 
explosive areas, caution and care should be exercised in choosing 
appropriate equipment and installing and using the equipment. Mention of 
trade names or company products does not constitute endorsement. All gas 
concentrations (percent, ppm) are by volume, unless otherwise noted.

                        2. Apparatus and Reagents

    2.1  Gas VOC concentration. A schematic of the measurement system is 
shown in Figure 1. The main components are described below:
    2.1.1  Dilution system. A Kipp in-stack dilution probe and 
controller or similar device may be used. The dilution rate may be 
changed by substituting different critical orifices or adjustments of 
the aspirator supply pressure. The dilution system shall be heated to 
prevent VOC condensation.

    Note: An out-of-stack dilution device may be used.

    2.1.2  Calibration valve assembly. Three-way valve assembly at the 
outlet of sample probe to direct the zero and calibration gases to the 
analyzer. Other methods, such as quick-connect lines, to route 
calibration gases to the outlet of the sample probe are acceptable.
    2.1.3  Sample line. Stainless steel or Teflon tubing to transport 
the sample gas to the analyzer. The sample line must be heated to 
prevent condensation.
    2.1.4  Sample pump. A leak-free pump, to pull the sample gas through 
the system at a flow rate sufficient to minimize the response time of 
the measurement system. The components of the pump that contract the gas 
stream shall be constructed of stainless steel or Teflon. The sample 
pump must be heated to prevent condensation.
    2.1.5  Sample flow rate control. A sample flow rate control valve 
and rotameter, or equivalent, to maintain a constant sampling rate 
within 10 percent. The flow control valve and rotameter must be heated 
to prevent condensation. A control valve may also be located on the 
sample pump bypass loop to assist in controlling the sample pressure and 
flow rate.
    2.1.6  Sample gas manifold. Capable of diverting a portion of the 
sample gas stream to the flame ionization analyzer (FIA), and the 
remainder to the bypass discharge vent. The manifold components shall be 
constructed of stainless steel or Teflon. If captured or fugitive 
emissions are to be measured at multiple locations, the measurement 
system shall be designed to use separate sampling probes, lines, and 
pumps for each measurement location and a common sample gas manifold and 
FIA. The sample gas manifold and connecting lines to the FIA must be 
heated to prevent condensation.
    2.1.7  Organic concentration analyzer. An FIA with a span value of 
1.5 times the expected concentration as propane; however, other span 
values may be used if it can be demonstrated that they would provide 
more accurate measurements.
    The system shall be capable of meeting or exceeding the following 
specifications:
    2.1.7.1  Zero drift. Less than 3.0 percent of the span 
value.
    2.1.7.2  Calibration drift. Less than 3.0 percent of the 
span value.
    2.1.7.3  Calibration error. Less than 5.0 percent of the 
calibration gas value.
    2.1.7.4  Response time. Less than 30 seconds.
    2.1.7.8  Integrator/data acquisition system. An analog or digital 
device or computerized data acquisition system used to integrate the FIA 
response or compute the average response and record measurement data. 
The minimum data sampling frequency for computing average or integrated 
values is one measurement value every 5 seconds. The device shall be 
capable of recording average values at least once per minute.
    2.1.9  Calibration and other gases. Gases used for calibration, 
fuel, and combustion air (if required) are contained in compressed gas 
cylinders. All calibration gases shall be

[[Page 416]]

traceable to NIST standards and shall be certified by the manufacturer 
to 1 percent of the tag value. Additionally, the 
manufacturer of the cylinder should provide a recommended shelf life for 
each calibration gas cylinder over which the concentration does not 
change more than 2 percent from the certified value. For 
calibration gas values not generally available, alternative methods for 
preparing calibration gas mixtures, such as dilution system, may be used 
with prior approval.
    2.1.9.1  Fuel. A 40 percent H2/60 percent He or 40 
percent H2/60 percent N2 gas mixture is 
recommended to avoid an oxygen synergism effect that reportedly occurs 
when oxygen concentration varies signficantly from a mean value.
    2.1.9.2.  Carrier gas and dilution air supply. High purity air with 
less than 1 ppm of organic material (as propane or carbon equivalent) or 
less than 0.1 percent of the span value, whichever is greater.
    2.1.9.3  FIA linearity calibration gases. Low-, mid-, and high-range 
gas mixture standards with nominal propane concentrations of 20-30, 45-
55, and 70-80 percent of the span value in air, respectively. Other 
calibration values and other span values may be used if it can be shown 
that more accurate measurements would be achieved.
    2.1.9.4  Dilution check gas. Gas mixture standard containing propane 
in air, approximately half the span value after dilution.
    2.1.10  Particulate filter. An in-stack or an out-of-stack glass 
fiber filter is recommended if exhaust gas particulate loading is 
significant. An out-of-stack filter must be heated to prevent any 
condensation unless it can be demonstrated that no condensation occurs.
    2.2  Captured emissions volumetric flow rate.
    2.2.1  Method 2 or 2A apparatus. For determining volumetric flow 
rate.
    2.2.2  Method 3 apparatus and reagents. For determining molecular 
weight of the gas stream. An estimate of the molecular weight of the gas 
stream may be used if it can be justified.
    2.2.3  Method 4 apparatus and reagents. For determining moisture 
content, if necessary.

     3. Determination of Volumetric Flow Rate of Captured Emissions

    3.1  Locate all points where emissions are captured from the 
affected facility. Using Method 1, determine the sampling points. Be 
sure to check each site for cyclonic or swirling flow.
    3.2  Measure the velocity at each sampling site at least once every 
hour during each sampling run using Method 2 or 2A.

          4. Determination of VOC Content of Captured Emissions

    4.1  Analysis duration. Measure the VOC responses at each captured 
emissions point during the entire test run or, if applicable, while the 
process is operating. If there are multiple captured emissions 
locations, design a sampling system to allow a single FIA to be used to 
determine the VOC responses at all sampling locations.
    4.2  Gas VOC concentration.
    4.2.1  Assemble the sample train as shown in Figure 1. Calibrate the 
FIA according to the procedure in section 5.1.
    4.2.2  Set the dilution ratio and determine the dilution factor 
according to the procedure in section 5.3.
    4.2.3  Conduct a system check according to the procedure in section 
5.4.
    4.2.4  Install the sample probe so that the probe is centrally 
located in the stack, pipe, or duct, and is sealed tightly at the stack 
port connection.
    4.2.5  Inject zero gas at the calibration valve assembly. Measure 
the system response time as the time required for the system to reach 
the effluent concentration after the calibration valve has been returned 
to the effluent sampling position.
    4.2.6  Conduct a system check before and a system drift check after 
each sampling run according to the procedures in sections 5.2 and 5.4. 
If the drift check following a run indicates unacceptable performance, 
the run is not valid. The tester may elect to perform system drift 
checks during the run not to exceed one drift check per hour.
    4.2.7  Verify that the sample lines, filter, and pump temperatures 
are 1205 deg.C.
    4.2.8  Begin sampling at the start of the test period and continue 
to sample during the entire run. Record the starting and ending times 
and any required process information as appropriate. If multiple 
captured emission locations are sampled using a single FIA, sample at 
each location for the same amount of time (e.g., 2 minutes) and continue 
to switch from one location to another for the entire test run. Be sure 
that total sampling time at each location is the same at the end of the 
test run. Collect at least 4 separate measurements from each sample 
point during each hour of testing. Disregard the measurements at each 
sampling location until two times the response time of the measurement 
system has elapsed. Continue sampling for at least 1 minute and record 
the concentration measurements.
    4.3  Background concentration.
    4.3.1  Locate all NDO's of the TTE. A sampling point shall be 
centrally located outside of the TTE at 4 equivalent diameters from each 
NDO, if possible. If there are more than 6 NDO's, choose 6 sampling 
points evenly spaced among the NDO's.

[[Page 417]]

    4.3.2  Assemble the sample train as shown in Figure 2. Calibrate the 
FIA and conduct a system check according to the procedures in sections 
5.1 and 5.4.
    4.3.3  Position the probe at the sampling location.
    4.3.4  Determine the response time, conduct the system check and 
sample according to the procedures described in sections 4.2.4 to 4.2.8.
    4.4  Alternative procedure. The direct interface sampling and 
analysis procedure described in section 7.2 of Method 18 may be used to 
determine the gas VOC concentration. The system must be designed to 
collect and analyze at least one sample every 10 minutes.

                  5. Calibration and Quality Assurance

    5.1  FIA Calibration and linearity check. Make necessary adjustments 
to the air and fuel supplies for the FIA and ignite the burner. Allow 
the FIA to warm up for the period recommended by the manufacturer. 
Inject a calibration gas into the measurement system after the dilution 
system and adjust the back-pressure regulator to the value required to 
achieve the flow rates specified by the manufacturer. Inject the zero- 
and the high-range calibration gases and adjust the analyzer calibration 
to provide the proper responses. Inject the low- and mid-range gases and 
record the responses of the measurement system. The calibration and 
linearity of the system are acceptable if the responses for all four 
gases are within 5 percent of the respective gas values. If the 
performance of the system is not acceptable, repair or adjust the system 
and repeat the linearity check. Conduct a calibration and linearity 
check after assembling the analysis system and after a major change is 
made to the system.
    5.2  Systems drift checks. Select the calibration gas that most 
closely approximates the concentration of the diluted captured emissions 
for conducting the drift checks. Introduce the zero and calibration gas 
at the calibration valve assembly and verify that the appropriate gas 
flow rate and pressure are present at the FIA. Record the measurement 
system responses to the zero and calibration gases. The performance of 
the system is acceptable if the difference between the drift check 
measurement and the value obtained in section 5.1 is less than 3 percent 
of the span value. Conduct the system drift check at the end of each 
run.
    5.3  Determination of dilution factor. Inject the dilution check gas 
into the measurement system before the dilution system and record the 
response. Calculate the dilution factor using Equation 3.
    5.4  System check. Inject the high range calibration gas at the 
inlet to the sampling probe while the dilution air is turned off. Record 
the response. The performance of the system is acceptable if the 
measurement system response is within 5 percent of the value obtained in 
section 5.1 for the high range calibration gas. Conduct a system check 
before and after each test run.
    5.5  Analysis audit. Immediately before each test analyze an audit 
cylinder as described in section 5.2. The analysis audit must agree with 
the audit cylinder concentration within 10 percent.

                             6. Nomenclature

Ai=area of NDO i, ft2.
AN=total area of all NDO's in the enclosure, ft2.
CA=actual concentration of the dilution check gas, ppm 
propane.
CBi=corrected average VOC concentration of background 
emissions at point i, ppm propane.
CB=average background concentration, ppm propane.
CDH=average measured concentration for the drift check 
calibration gas, ppm propane.
CDO=average system drift check concentration for zero 
concentration gas, ppm propane.
CH=actual concentration of the drift check calibration, gas, 
ppm propane.
Ci=uncorrected average background VOC concentration measured 
at point i, ppm propane.
Cj=uncorrected average VOC concentration measured at point j, 
ppm propane.
CM=measured concentration of the dilution check gas, ppm 
propane.
DF=dilution factor.
G=total VOC content of captured emissions, kg.
K1=1.830  x  10-6 kg/(m3-ppm).
n=number of measurement points.
QGj=average effluent volumetric flow rate corrected to 
standard conditions at captured emissions point j, m3/min.
TC=total duration of capture efficiency sampling run, min.

                             7. Calculations

    7.1 Total VOC captured emissions.
    [GRAPHIC] [TIFF OMITTED] TC07NO91.016
    
    7.2 VOC concentration of the captured emissions to point j.

[[Page 418]]

[GRAPHIC] [TIFF OMITTED] TC07NO91.017


    7.3 Dilution factor.
    [GRAPHIC] [TIFF OMITTED] TC07NO91.018
    
    7.4 Background VOC concentration at point i.
    [GRAPHIC] [TIFF OMITTED] TC07NO91.019
    
    7.5 Average background concentration.
    [GRAPHIC] [TIFF OMITTED] TC07NO91.020
    

    Note: If the concentration at each point is within 20 percent of the 
average concentration of all points, the terms ``Ai'' and 
``AN'' may be deleted from Equation 4.



[[Page 419]]

[GRAPHIC] [TIFF OMITTED] TC01MY92.097



[[Page 420]]

[GRAPHIC] [TIFF OMITTED] TC01MY92.098



[[Page 421]]

     Procedure F.2--Fugitive VOC Emissions from Building Enclosures

                             1. Introduction

    1.1  Applicability. This procedure is applicable for determining the 
fugitive volatile organic compounds (VOC) emissions from a building 
enclosure (BE). It is intended to be used as a segment in the 
development of liquid/gas or gas/gas protocols for determining VOC 
capture efficiency (CE) for surface coating and printing operations.
    1.2  Principle. The total amount of fugitive VOC emissions 
(FB) from the BE is calculated as the sum of the products of 
the VOC content (CFj) of each fugitive emissions point, its 
flow rate (QFj), and time (TF).
    1.3  Measurement uncertainty. The measurement uncertainties are 
estimated for each fugitive emissions point as follows: 
QFj=5.0 percent and 
CFj=5.0 percent. Based on these numbers, the 
probable uncertainty for FB is estimated at about 
11.2 percent.
    1.4  Sampling requirements. A capture efficiency test shall consist 
of at least three sampling runs. The sampling time for each run should 
be at least 8 hours, unless otherwise approved.
    1.5  Notes. Because this procedure is often applied in highly 
explosive areas, caution and care should be exercised in choosing 
appropriate equipment and installing and using the equipment. Mention of 
trade names or company products does not constitute endorsement. All gas 
concentrations (percent, ppm) are by volume, unless otherwise noted.

                        2. Apparatus and Reagents

    2.1  Gas VOC concentration. A schematic of the measurement system is 
shown in Figure 1. The main components are described below:
    2.1.1  Sample probe. Stainless steel, or equivalent. The probe shall 
be heated to prevent VOC condensation.
    2.1.2  Calibration valve assembly. Three-way valve assembly at the 
outlet of sample probe to direct the zero and calibration gases to the 
analyzer. Other methods, such as quick-connect lines, to route 
calibration gases to the outlet of the sample probe are acceptable.
    2.1.3  Sample line. Stainless steel or Teflon tubing to transport 
the sample gas to the analyzer. The sample line must be heated to 
prevent condensation.
    2.1.4  Sample pump. A leak-free pump, to pull the sample gas through 
the system at a flow rate sufficient to minimize the response time of 
the measurement system. The components of the pump that contact the gas 
stream shall be constructed of staimust be heated to prevent 
condensation.
    2.1.5  Sample flow rate control. A sample flow rate control valve 
and rotameter, or equivalent, to maintain a constant sampling rate 
within 10 percent. The flow rate control valve and rotameter must be 
heated to prevent condensation. A control valve may also be located on 
the sample pump bypass loop to assist in controlling the sample pressure 
and flow rate.
    2.1.6  Sample gas manifold. Capable of diverting a portion of the 
sample gas stream to the flame ionization analyzer (FIA), and the 
remainder to the bypass discharge vent. The manifold components shall be 
constructed of stainless steel or Teflon. If emissions are to be 
measured at multiple locations, the measurement system shall be designed 
to use separate sampling probes, lines, and pumps for each measurement 
location and a common sample gas manifold and FIA. The sample gas 
manifold must be heated to prevent condensation.
    2.1.7  Organic Concentration Analyzer. An FIA with a span value of 
1.5 times the expected concentration as propane; however, other span 
values may be used if it can be demonstrated that they would provide 
more accurate measurements. The system shall be capable or exceeding the 
following specifications:
    2.1.7.1  Zero drift. Less than 3.0 percent of the span 
value.
    2.1.7.2  Calibration drift. Less than 3.0 percent of the 
span value.
    2.1.7.3  Calibration error. Less than 5.0 percent of the 
calibration gas value.
    2.1.7.4  Response time. Less than 30 seconds.
    2.1.8  Integrator/data acquisition system. An analog or digital 
device or computerized data acquisition system used to integrate the FIA 
response or compute the average response and record measurement data. 
The minimum data sampling frequency for computing average or integrated 
values is one measurement value every 5 seconds. The device shall be 
capable of recording average values at least once per minute.
    2.1.9  Calibration and other gases. Gases used for calibration, 
fuel, and combustion air (if required) are contained in compressed gas 
cylinders. All calibration gases shall be traceable to NIST standards 
and shall be certified by the manufacturer to 1 percent of 
the tag value. Additionally, the manufacturer of the cylinder should 
provide a recommended shelf life for each calibration gas cylinder over 
which the concentration does not change more than 2 percent 
from the certified value. For calibration gas values not generally 
available, alternative methods for preparing calibration gas mixtures, 
such as dilution systems, may be used with prior approval.
    2.1.9.1  Fuel. A 40 percent H2/60 percent He or 40 
percent H2/60 percent N2 gas mixture is 
recommended to avoid an oxygen synergism effect that reportedly occurs 
when oxygen concentration varies significantly from a mean value.
    2.1.9.2  Carrier gas. High purity air with less than 1 ppm of 
organic material (propane

[[Page 422]]

or carbon equivalent) or less than 0.1 percent of the span value, 
whichever is greater.
    2.1.9.3  FIA linearity calibration gases. Low-, mid-, and high-range 
gas mixture standards with nominal propane concentrations of 20-30, 45-
55, and 70-80 percent of the span value in air, respectively. Other 
calibration values and other span values may be used if it can be shown 
that more accurate measurements would be achieved.
    2.1.10  Particulate filter. An in-stack or an out-of-stack glass 
fiber filter is recommended if exhaust gas particulate loading is 
significant. An out-of-stack filter must be heated to prevent any 
condensation unless it can be demonstrated that no condensation occurs.
    2.2  Fugitive emissions volumetric flow rate.
    2.2.1  Flow direction indicators. Any means of indicating inward or 
outward flow, such as light plastic film or paper streamers, smoke 
tubes, filaments, and sensory perception.
    2.2.2  Method 2 or 2A apparatus. For determining volumetric flow 
rate. Anemometers or similar devices calibrated according to the 
manufacturer's instructions may be used when low velocities are present. 
Vane anemometers (Young-maximum response propeller), specialized pitots 
with electronic manometers (e.g., Shortridge Instruments Inc., Airdata 
Multimeter 860) are commercially available with measurement thresholds 
of 15 and 8 mpm (50 and 25 fpm), respectively.
    2.2.3  Method 3 apparatus and reagents. For determining molecular 
weight of the gas stream. An estimate of the molecular weight of the gas 
stream may be used if it can be justified.
    2.2.4  Method 4 apparatus and reagents. For determining moisture 
content, if necessary.

     3. Determination of Volumetric Flow Rate of Fugitive Emissions

    3.1  Preliminary determinations. The purpose of this exercise is to 
determine which exhaust points should be measured for volumetric flow 
rates and VOC concentrations.
    3.1.1  Forced draft openings. Identify all forced draft openings. 
Determine the volumetric flow rate according to Method 2.
    3.1.2  NDO's exhaust points. The NDO's in the roof of a facility are 
considered to be exhaust points. Determine volumetric flow rate from 
these NDO's. Divide the cross-sectional area according to Method 1 using 
12 equal areas. Use the appropriate velocity measurement devices, e.g., 
propeller anemometers.
    3.1.3  Other NDO's.
    3.1.3.1  This step is optional. Determine the exhaust flow rate, 
including that of the control device, from the enclosure and the intake 
air flow rate. If the exhaust flow rate divided by the intake air flow 
rate is greater than 1.1, then all other NDO's are not considered to be 
significant exhaust points.
    3.1.3.2  If the option above is not taken, identify all other NDO's 
and other potential points through which fugitive emissions may escape 
the enclosure. Then use the following criteria to determine whether flow 
rates and VOC concentrations need to be measured:
    3.1.3.2.1  Using the appropriate flow direction indicator, determine 
the flow direction. An NDO with zero or inward flow is not an exhaust 
point.
    3.1.3.2.2  Measure the outward volumetric flow rate from the 
remainder of the NDO's. If the collective flow rate is 2 percent, or 
less, of the flow rate from sections 3.1.1 and 3.1.2, then these NDO's, 
except those within two equivalent diameters (based on NDO opening) from 
VOC sources, may be considered to be non-exhaust points.
    3.1.3.2.3  If the percentage calculated in section 3.1.3.2.2 is 
greater than 2 percent, those NDO's (except those within two equivalent 
diameters from VOC sources) whose volumetric flow rate totals 2 percent 
of the flow rate from sections 3.1.1 and 3.1.2 may be considered as non-
exhaust points. All remaining NDO's shall be measured for volumetric 
flow rate and VOC concentrations during the CE test.
    3.1.3.2.4  The tester may choose to measure VOC concentrations at 
the forced exhaust points and the NDO's. If the total VOC emissions from 
the NDO's are less than 2 percent of the emissions from the forced draft 
and roof NDO's, then these NDO's may be eliminated from further 
consideration.
    3.2  Determination of flow rates.
    3.2.1  Measure the volumetric flow rate at all locations identified 
as exhaust points in section 3.1. Divide each exhaust opening into 9 
equal areas for rectangular openings and 8 for circular openings.
    3.2.2  Measure the velocity at each site at least once every hour 
during each sampling run using Method 2 or 2A, if applicable, or using 
the low velocity instruments in section 2.2.2.

          4. Determination of VOC Content of Fugitive Emissions

    4.1  Analysis duration. Measure the VOC responses at each fugitive 
emission point during the entire test run or, if applicable, while the 
process is operating. If there are multiple emissions locations, design 
a sampling system to allow a single FIA to be used to determine the VOC 
responses at all sampling locations.
    4.2  Gas VOC concentration.
    4.2.1  Assemble the sample train as shown in Figure 1. Calibrate the 
FIA and conduct a system check according to the procedures in sections 
5.1 and 5.3, respectively.
    4.2.2  Install the sample probe so that the probe is centrally 
located in the stack, pipe, or duct, and is sealed tightly at the stack 
port connection.

[[Page 423]]

    4.2.3  Inject zero gas at the calibration valve assembly. Allow the 
measurement system response to reach zero. Measure the system response 
time as the time required for the system to reach the effluent 
concentration after the calibration valve has been returned to the 
effluent sampling position.
    4.2.4  Conduct a system check before and a system drift check after 
each sampling run according to the procedures in sections 5.2 and 5.3. 
If the drift check following a run indicates unacceptable performance, 
the run is not valid. The tester may elect to perform drift checks 
during the run not to exceed one drift check per hour.
    4.2.5  Verify that the sample lines, filter, and pump temperatures 
are 1205 deg.C.
    4.2.6  Begin sampling at the start of the test period and continue 
to sample during the entire run. Record the starting and ending times 
and any required process information as appropriate. If multiple 
emission locations are sampled using a single FIA, sample at each 
location for the same amount of time (e.g., 2 minutes) and continue to 
switch from one location to another for the entire test run. Be sure 
that total sampling time at each location is the same at the end of the 
test run. Collect at least 4 separate measurements from each sample 
point during each hour of testing. Disregard the response measurements 
at each sampling location until two times the response time of the 
measurement system has elapsed. Continue sampling for at least 1 minute 
and record the concentration measurements.
    4.3  Alternative procedure. The direct interface sampling and 
analysis procedure described in section 7.2 of Method 18 may be used to 
determine the gas VOC concentration. The system must be designed to 
collect and analyze at least one sample every 10 minutes.

                  5. Calibration and Quality Assurance

    5.1  FIA calibration and linearity check. Make necessary adjustments 
to the air and fuel supplies for the FIA and ignite the burner. Allow 
the FIA to warm up for the period recommended by the manufacturer. 
Inject a calibration gas into the measurement system and adjust the 
back-pressure regulator to the value required to achieve the flow rates 
specified by the manufacturer. Inject the zero- and the high-range 
calibration gases and adjust the analyzer calibration to provide the 
proper responses. Inject the low- and mid-range gases and record the 
responses of the measurement system. The calibration and linearity of 
the system are acceptable if the responses for all four gases are within 
5 percent of the respective gas values. If the performance of the system 
is not acceptable, repair or adjust the system and repeat the linearity 
check. Conduct a calibration and linearity check after assembling the 
analysis system and after a major change is made to the system.
    5.2  Systems drift checks. Select the calibration gas that most 
closely approximates the concentration of the captured emissions for 
conducting the drift checks. Introduce the zero and calibration gas at 
the calibration valve assembly and verify that the appropriate gas flow 
rate and pressure are present at the FIA. Record the measurement system 
responses to the zero and calibration gases. The performance of the 
system is acceptable if the difference between the drift check 
measurement and the value obtained in section 5.1 is less than 3 percent 
of the span value. Conduct a system drift check at the end of each run.
    5.3  System check. Inject the high range calibration gas at the 
inlet of the sampling probe and record the response. The performance of 
the system is acceptable if the measurement system response is within 5 
percent of the value obtained in section 5.1 for the high range 
calibration gas. Conduct a system check before each test run.
    5.4  Analysis audit. Immediately before each test analyze an audit 
cylinder as described in section 5.2. The analysis audit must agree with 
the audit cylinder concentration within 10 percent.

                             6. Nomenclature

CDH=average measured concentration for the drift check 
calibration gas, ppm propane.
CDO=average system drift check concentration for zero 
concentration gas, ppm propane.
CFj=corrected average VOC concentration of fugitive emissions 
at point j, ppm propane.
CH=actual concentration of the drift check calibration gas, 
ppm propane.
Cj=uncorrected average VOC concentration measured at point j, 
ppm propane.
FB=total VOC content of fugitive emissions from the building, 
kg.
K1=1.830 x 10-6 kg/(m3-ppm).
n=number of measurement points.
QFj=average effluent volumetric flow rate corrected to 
standard conditions at fugitive emissions point j, m\3\/min.
TF=total duration of capture efficiency sampling run, min.

                             7. Calculations

    7.1  Total VOC fugitive emissions from the building.
    [GRAPHIC] [TIFF OMITTED] TC07NO91.021
    
    7.2  VOC concentration of the fugitive emissions at point j.

[[Page 424]]

[GRAPHIC] [TIFF OMITTED] TC07NO91.022


[GRAPHIC] [TIFF OMITTED] TC01MY92.099


[[Page 425]]



     Procedure F.1--Fugitive VOC Emissions From Temporary Enclosures

                             1. Introduction

    1.1  Applicability. This procedure is applicable for determining the 
fugitive volatile organic compounds (VOC) emissions from a temporary 
total enclosure (TTE). It is intended to be used as a segment in the 
development of liquid/gas or gas/gas protocols for determining VOC 
capture efficiency (CE) for surface coating and printing operations.
    1.2  Principle. The amount of fugitive VOC emissions (F) from the 
TTE is calculated as the sum of the products of the VOC content 
(CFj), the flow rate (QFj), and the sampling time 
(TF) from each fugitive emissions point.
    1.3  Estimated measurement uncertainty. The measurement 
uncertainties are estimated for each fugitive emission point as follows: 
 Q=5.5 percent and CFj=5.0 percent. 
Based on these numbers, the probable uncertainty for F is estimated at 
about 7.4 percent.
    1.4  Sampling requirements. A capture efficiency test shall consist 
of at least three sampling runs. The sampling time for each run should 
be at least 8 hours, unless otherwise approved.
    1.5  Notes. Because this procedure is often applied in highly 
explosive areas, caution and care should be exercised in choosing 
appropriate equipment and installing and using the equipment. Mention of 
trade names or company products does not constitute endorsement. All gas 
concentrations (percent, ppm) are by volume, unless otherwise noted.

                        2. Apparatus and Reagents

    2.1  Gas VOC concentration. A schematic of the measurement system is 
shown in Figure 1. The main components are described below:
    2.1.1  Sample probe. Stainless steel, or equivalent. The probe shall 
be heated to prevent VOC condensation.
    2.1.2  Calibration valve assembly. Three-way valve assembly at the 
outlet of sample probe to direct the zero and calibration gases to the 
analyzer. Other methods, such as quick-connect lines, to route 
calibration gases to the outlet of the sample probe are acceptable.
    2.1.3  Sample line. Stainless steel or Teflon tubing to transport 
the sample gas to the analyzer. The sample line must be heated to 
prevent condensation.
    2.1.4  Sample pump. A leak-free pump, to pull the sample gas through 
the system at a flow rate sufficient to minimize the response time of 
the measurement system. The components of the pump that contact the gas 
stream shall be constructed of stainless steel or Teflon. The sample 
pump must be heated to prevent condensation.
    2.1.5  Sample flow rate control. A sample flow rate control valve 
and rotameter, or equivalent, to maintain a constant sampling rate 
within 10 percent. The flow control valve and rotameter must be heated 
to prevent condensation. A control valve may also be located on the 
sample pump bypass loop to assist in controlling the sample pressure and 
flow rate.
    2.1.6  Sample gas manifold. Capable of diverting a portion of the 
sample gas stream to the flame ionization analyzer (FIA), and the 
remainder to the bypass discharge vent. The manifold components shall be 
constructed of stainless steel or Teflon. If emissions are to be 
measured at multiple locations, the measurement system shall be designed 
to use separate sampling probes, lines, and pumps for each measurement 
location and a common sample gas manifold and FIA. The sample gas 
manifold and connecting lines to the FIA must be heated to prevent 
condensation.
    2.1.7  Organic concentration analzyer. An FIA with a span value of 
1.5 times the expected concentration as propane; however, other span 
values may be used if it can be demonstrated that they would provide 
more accurate measurements. The system shall be capable of meeting or 
exceeding the following specifications:
    2.1.7.1  Zero drift. Less than 3.0 percent of the span 
value.
    2.1.7.2  Calibration drift. Less than 3.0 percent of the 
span value.
    2.1.7.3  Calibration error. Less than 5.0 percent of the 
calibration gas value.
    2.1.7.4  Response time. Less than 30 seconds.
    2.1.8  Integrator/data acquisition system. An analog or digital 
device or computerized data acquisition system used to integrate the FIA 
response or compute the average response and record measurement data. 
The minimum data sampling frequency for computing average or integrated 
values is one measurement value every 5 seconds. The device shall be 
capable of recording average values at least once per minute.
    2.1.9  Calibration and other gases. Gases used for calibration, 
fuel, and combustion air (if required) are contained in compressed gas 
cylinders. All calibration gases shall be traceable to NIST standards 
and shall be certified by the manufacturer to 1 percent of 
the tag value. Additionally, the manufacturer of the cylinder should 
provide a recommended shelf life for each calibration gas cylinder over 
which the concentration does not change more than 2 percent 
from the certified value. For calibration gas values not generally 
available, alternative methods for preparing calibration gas mixtures, 
such as dilution systems, may be used with prior approval.
    2.1.9.1  Fuel. A 40 percent H2/60 percent He or 40 
percent H2/60 percent N2 gas mixture is 
recommended to avoid an oxygen synergism effect that reportedly occurs 
when oxygen concentration varies significantly from a mean value.

[[Page 426]]

    2.1.9.2  Carrier gas. High purity air with less than 1 ppm of 
organic material (as propane or carbon equivalent) or less than 0.1 
percent of the span value, whichever is greater.
    2.1.9.3  FIA linearity calibration gases. Low-, mid-, and high-range 
gas mixture standards with nominal propane concentrations of 20-30, 45-
55, and 70-80 percent of the span value in air, respectively. Other 
calibration values and other span values may be used if it can be shown 
that more accurate measurements would be achieved.
    2.1.10  Particulate filter. An in-stack or an out-of-stack glass 
fiber filter is recommended if exhaust gas particulate loading is 
significant. An out-of-stack filter must be heated to prevent any 
condensation unless it can be demonstrated that no condensation occurs.
    2.2  Fugitive emissions volumetric flow rate.
    2.2.1  Method 2 or 2A apparatus. For determining volumetric flow 
rate.
    2.2.2  Method 3 apparatus and reagents. For determining molecular 
weight of the gas stream. An estimate of the molecular weight of the gas 
stream may be used if it can be justified.
    2.2.3  Method 4 apparatus and reagents. For determining moisture 
content, if necessary.
    2.3  Temporary total enclosure. The criteria for designing a TTE are 
discussed in Procedure T.

     3. Determination of Volumetric Flow Rate of Fugitive Emissions

    3.1  Locate all points where emissions are exhausted from the TTE. 
Using Method 1, determine the sampling points. Be sure to check each 
site for cyclonic or swirling flow.
    3.2  Measure the velocity at each sampling site at least once every 
hour during each sampling run using Method 2 or 2A.

          4. Determination of VOC Content of Fugitive Emissions

    4.1  Analysis duration. Measure the VOC responses at each fugitive 
emission point during the entire test run or, if applicable, while the 
process is operating. If there are multiple emission locations, design a 
sampling system to allow a single FIA to be used to determine the VOC 
responses at all sampling locations.
    4.2  Gas VOC concentration.
    4.2.1  Assemble the sample train as shown in Figure 1. Calibrate the 
FIA and conduct a system check according to the procedures in sections 
5.1 and 5.3, respectively.
    4.2.2  Install the sample probe so that the probe is centrally 
located in the stack, pipe, or duct, and is sealed tightly at the stack 
port connection.
    4.2.3  Inject zero gas at the calibration valve assembly. Allow the 
measurement system response to reach zero. Measure the system response 
time as the time required for the system to reach the effluent 
concentration after the calibration valve has been returned to the 
effluent sampling position.
    4.2.4  Conduct a system check before and a system drift check after 
each sampling run according to the procedures in sections 5.2 and 5.3. 
If the drift check following a run indicates unacceptable performance, 
the run is not valid. The tester may elect to perform system drift 
checks during the run not to exceed one drift check per hour.
    4.2.5  Verify that the sample lines, filter, and pump temperatures 
are 120  5  deg.C.
    4.2.6  Begin sampling at the start of the test period and continue 
to sample during the entire run. Record the starting and ending times 
and any required process information as appropriate. If multiple 
emission locations are sampled using a single FIA, sample at each 
location for the same amount of time (e.g., 2 minutes) and continue to 
switch from one location to another for the entire test run. Be sure 
that total sampling time at each location is the same at the end of the 
test run. Collect at least 4 separate measurements from each sample 
point during each hour of testing. Disregard the response measurements 
at each sampling location until two times the response time of the 
measurement system has elapsed. Continue sampling for at least 1 minute 
and record the concentration measurements.
    4.3  Background concentration.
    4.3.1  Determination of VOC background concentration.
    4.3.1.1  Locate all NDO's of the TTE. A sampling point shall be 
centrally located outside of the TTE at 4 equivalent diameters from each 
NDO, if possible. If there are more than 6 NDO's, choose 6 sampling 
points evenly spaced among the NDO's.
    4.3.1.2  Assemble the sample train as shown in Figure 2. Calibrate 
the FIA and conduct a system check according to the procedures in 
sections 5.1 and 5.3.
    4.3.1.3  Position the probe at the sampling location.
    4.3.1.4  Determine the response time, conduct the system check and 
sample according to the procedures described in sections 4.2.3 to 4.2.6.
    4.4  Alternative procedure. The direct interface sampling and 
analysis procedure described in section 7.2 of Method 18 may be used to 
determine the gas VOC concentration. The system must be designed to 
collect and analyze at least one sample every 10 minutes.

                  5. Calibration and Quality Assurance

    5.1  FIA calibration and linearity check. Make necessary adjustments 
to the air and fuel supplies for the FIA and ignite the burner. Allow 
the FIA to warm up for the period recommended by the manufacturer. 
Inject a

[[Page 427]]

calibration gas into the measurement system and adjust the back-pressure 
regulator to the value required to achieve the flow rates specified by 
the manufacturer. Inject the zero- and the high-range calibration gases 
and adjust the analyzer calibration to provide the proper responses. 
Inject the low- and mid-range gases and record the responses of the 
measurement system. The calibration and linearity of the system are 
acceptable if the responses for all four gases are within 5 percent of 
the respective gas values. If the performance of the system is not 
acceptable, repair or adjust the system and repeat the linearity check. 
Conduct a calibration and linearity check after assembling the analysis 
system and after a major change is made to the system.
    5.2  Systems drift checks. Select the calibration gas concentration 
that most closely approximates that of the fugitive gas emissions to 
conduct the drift checks. Introduce the zero and calibration gas at the 
calibration valve assembly and verify that the appropriate gas flow rate 
and pressure are present at the FIA. Record the measurement system 
responses to the zero and calibration gases. The performance of the 
system is acceptable if the difference between the drift check 
measurement and the value obtained in section 5.1 is less than 3 percent 
of the span value. Conduct a system drift check at the end of each run.
    5.3  System check. Inject the high range calibration gas at the 
inlet of the sampling probe and record the response. The performance of 
the system is acceptable if the measurement system response is within 5 
percent of the value obtained in section 5.1 for the high range 
calibration gas. Conduct a system check before each test run.
    5.4  Analysis audit. Immediately before each test analyze an audit 
cylinder as described in section 5.2. The analysis audit must agree with 
the audit cylinder concentration within 10 percent.

                             6. Nomenclature

Ai=area of NDO i, ft\2\.
AN=total area of all NDO's in the enclosure, ft\2\.
CBi=corrected average VOC concentration of background 
          emissions at point i, ppm propane.
CB=average background concentration, ppm propane.
CDH=average measured concentration for the drift check 
          calibration gas, ppm propane.
CDO=average system drift check concentration for zero 
          concentration gas, ppm propane.
CFj=corrected average VOC concentration of fugitive emissions 
          at point j, ppm propane.
CH=actual concentration of the drift check calibration gas, 
          ppm propane.
Ci=uncorrected average background VOC concentration at point 
          i, ppm propane.
Cj=uncorrected average VOC concentration measured at point j, 
          ppm propane.
F=total VOC content of fugitive emissions, kg.
K1=1.830 x 10-6 kg/(m3-ppm).
n=number of measurement points.
QFj=average effluent volumetric flow rate corrected to 
          standard conditions at fugitive emissions point j, m\3\/min.
TF=total duration of fugitive emissions sampling run, min.

                             7. Calculations

    7.1  Total VOC fugitive emissions.
    [GRAPHIC] [TIFF OMITTED] TC07NO91.023
    
    7.2  VOC concentration of the fugitive emissions at point j.
    [GRAPHIC] [TIFF OMITTED] TC07NO91.024
    
    7.3  Background VOC concentration at point i.
    [GRAPHIC] [TIFF OMITTED] TC07NO91.025
    
    7.4  Average background concentration.
    [GRAPHIC] [TIFF OMITTED] TC07NO91.026
    

    Note: If the concentration at each point is within 20 percent of the 
average concentration of all points, the terms ``Ai'' and 
``AN'' may be deleted from Equation 4.



[[Page 428]]

[GRAPHIC] [TIFF OMITTED] TC01MY92.100



[[Page 429]]

[GRAPHIC] [TIFF OMITTED] TC01MY92.101



[[Page 430]]

                         Procedure L--VOC Input

                             1. Introduction

    1.1  Applicability. This procedure is applicable for determining the 
input of volatile organic compounds (VOC). It is intended to be used as 
a segment in the development of liquid/gas protocols for determining VOC 
capture efficiency (CE) for surface coating and printing operations.
    1.2  Principle. The amount of VOC introduced to the process (L) is 
the sum of the products of the weight (W) of each VOC containing liquid 
(ink, paint, solvent, etc.) used and its VOC content (V). A sample of 
each VOC containing liquid is analyzed with a flame ionization analyzer 
(FIA) to determine V.
    1.3  Estimated measurement uncertainty. The measurement 
uncertainties are estimated for each VOC containing liquid as follows: 
W=2.0 percent and V=12.0 percent. Based on these 
numbers, the probable uncertainty for L is estimated at about 
12.2 percent for each VOC containing liquid.
    1.4  Sampling requirements. A capture efficiency test shall consist 
of at least three sampling runs. The sampling time for each run should 
be at least 8 hours, unless otherwise approved.
    1.5  Notes. Because this procedure is often applied in highly 
explosive areas, caution and care should be exercised in choosing 
appropriate equipment and installing and using the equipment. Mention of 
trade names or company products does not constitute endorsement. All gas 
concentrations (percent, ppm) are by volume, unless otherwise noted.

                        2. Apparatus and Reagents

    2.1  Liquid weight.
    2.1.1  Balances/digital scales. To weigh drums of VOC containing 
liquids to within 0.2 lb.
    2.1.2  Volume measurement apparatus (alternative). Volume meters, 
flow meters, density measurement equipment, etc., as needed to achieve 
same accuracy as direct weight measurements.
    2.2  VOC content (flame ionization analyzer technique). The liquid 
sample analysis system is shown in Figures 1 and 2. The following 
equipment is required:
    2.2.1  Sample collection can. An appropriately sized metal can to be 
used to collect VOC containing materials. The can must be constructed in 
such a way that it can be grounded to the coating container.
    2.2.2  Needle valves. To control gas flow.
    2.2.3  Regulators. For carrier gas and calibration gas cylinders.
    2.2.4  Tubing. Teflon or stainless steel tubing with diameters and 
lengths determined by connection requirements of equipment. The tubing 
between the sample oven outlet and the FIA shall be heated to maintain a 
temperature of 1205  deg.C.
    2.2.5  Atmospheric vent. A tee and 0- to 0.5-liter/min rotameter 
placed in the sampling line between the carrier gas cylinder and the VOC 
sample vessel to release the excess carrier gas. A toggle valve placed 
between the tee and the rotameter facilitates leak tests of the analysis 
system.
    2.2.6  Thermometer. Capable of measuring the temperature of the hot 
water bath to within 1  deg.C.
    2.2.7  Sample oven. Heated enclosure, containing calibration gas 
coil heaters, critical orifice, aspirator, and other liquid sample 
analysis components, capable of maintaining a temperature of 
1205  deg.C.
    2.2.8  Gas coil heaters. Sufficient lengths of stainless steel or 
Teflon tubing to allow zero and calibration gases to be heated to the 
sample oven temperature before entering the critical orifice or 
aspirator.
    2.2.9  Water bath. Capable of heating and maintaining a sample 
vessel temperature of 1005  deg.C.
    2.2.10  Analytical balance. To measure 0.001 g.
    2.2.11  Disposable syringes. 2-cc or 5-cc.
    2.2.12  Sample vessel. Glass, 40-ml septum vial. A separate vessel 
is needed for each sample.
    2.2.13  Rubber stopper. Two-hole stopper to accommodate 3.2-mm (\1/
8\-in.) Teflon tubing, appropriately sized to fit the opening of the 
sample vessel. The rubber stopper should be wrapped in Teflon tape to 
provide a tighter seal and to prevent any reaction of the sample with 
the rubber stopper. Alternatively, any leak-free closure fabricated of 
non-reactive materials and accommodating the necessary tubing fittings 
may be used.
    2.2.14  Critical orifices. Calibrated critical orifices capable of 
providing constant flow rates from 50 to 250 ml/min at known pressure 
drops. Sapphire orifice assemblies (available from O'Keefe Controls 
Company) and glass capillary tubing have been found to be adequate for 
this application.
    2.2.15  Vacuum gauge. 0 -to 760-mm (0- to 30-in.) Hg U-Tube 
manometer or vacuum gauge.
    2.2.16  Pressure gauge. Bourdon gauge capable of measuring the 
maximum air pressure at the aspirator inlet (e.g., 100 psig).
    2.2.17  Aspirator. A device capable of generating sufficient vacuum 
at the sample vessel to create critical flow through the calibrated 
orifice when sufficient air pressure is present at the aspirator inlet. 
The aspirator must also provide sufficient sample pressure to operate 
the FIA. The sample is also mixed with the dilution gas within the 
aspirator.
    2.2.18  Soap bubble meter. Of an appropriate size to calibrate the 
critical orifices in the system.
    2.2.19  Organic concentration analyzer. An FIA with a span value of 
1.5 times the expected concentration as propane; however

[[Page 431]]

other span values may be used if it can be demonstrated that they would 
provide more accurate measurements. The system shall be capable of 
meeting or exceeding the following specifications:
    2.2.19.1  Zero drift. Less than 3.0 percent of the span 
value.
    2.2.19.2  Calibration drift. Less than 3.0 percent of 
span value.
    2.2.19.3  Calibration error. Less than 5.0 percent of 
the calibration gas value.
    2.2.20  Integrator/data acquisition system. An analog or digital 
device or computerized data acquisition system used to integrate the FIA 
response or compute the average response and record measurement data. 
The minimum data sampling frequency for computing average or integrated 
values is one measurement value every 5 seconds. The device shall be 
capable of recording average values at least once per minute.
    2.2.21  Chart recorder (optional). A chart recorder or similar 
device is recommended to provide a continuous analog display of the 
measurement results during the liquid sample analysis.
    2.2.22  Calibration and other gases. For calibration, fuel, and 
combustion air (if required) contained in compressed gas cylinders. All 
calibration gases shall be traceable to NIST standards and shall be 
certified by the manufacturer to 1 percent of the tag value. 
Additionally, the manufacturer of the cylinder should provide a 
recommended shelf life for each calibration gas cylinder over which the 
concentration does not change more than 2 percent from the 
certified value. For calibration gas values not generally available, 
alternative methods for preparing calibration gas mixtures, such as 
dilution systems, may be used with prior approval.
    2.2.22.1  Fuel. A 40 percent H2/60 percent He or 40 
percent H2/60 percent N2 gas mixture is 
recommended to avoid an oxygen synergism effect that reportedly occurs 
when oxygen concentration varies significantly from a mean value.
    2.2.22.2  Carrier gas. High purity air with less than 1 ppm of 
organic material (as propane) or less than 0.1 percent of the span 
value, whichever is greater.
    2.2.22.3  FIA linearity calibration gases. Low-, mid-, and high-
range gas mixture standards with nominal propane concentrations of 20-
30, 45-55, and 70-80 percent of the span value in air, respectively. 
Other calibration values and other span values may be used if it can be 
shown that more accurate measurements would be achieved.
    2.2.22.4  System calibration gas. Gas mixture standard containing 
propane in air, approximately the undiluted VOC concentration expected 
for the liquid samples.

                 3. Determination of Liquid Input Weight

    3.1  Weight difference. Determine the amount of material introduced 
to the process as the weight difference of the feed material before and 
after each sampling run. In determining the total VOC containing liquid 
usage, account for: (a) The initial (beginning) VOC containing liquid 
mixture; (b) any solvent added during the test run; (c) any coating 
added during the test run; and (d) any residual VOC containing liquid 
mixture remaining at the end of the sample run.
    3.1.1  Identify all points where VOC containing liquids are 
introduced to the process. To obtain an accurate measurement of VOC 
containing liquids, start with an empty fountain (if applicable). After 
completing the run, drain the liquid in the fountain back into the 
liquid drum (if possible), and weigh the drum again. Weigh the VOC 
containing liquids to 0.5 percent of the total weight (full) 
or 0.1 percent of the total weight of VOC containing liquid 
used during the sample run, whichever is less. If the residual liquid 
cannot be returned to the drum, drain the fountain into a preweighted 
empty drum to determine the final weight of the liquid.
    3.1.2  If it is not possible to measure a single representative 
mixture, than weigh the various components separately (e.g., if solvent 
is added during the sampling run, weigh the solvent before it is added 
to the mixture). If a fress drum of VOC containing liquid is needed 
during the run, then weigh both the empty drum and fresh drum.
    3.2  Volume measurement (alternative). If direct weight measurements 
are not feasible, the tester may use volume meters and flow rate meters 
(and density measurements) to determine the weight of liquids used if it 
can be demonstrated that the technique produces results equivalent to 
the direct weight measurements. If a single representative mixture 
cannot be measured, measure the components separately.

            4. Determination of VOC Content in Input Liquids

    4.1  Collection of liquid samples.
    4.1.1  Collect a 100-ml or larger sample of the VOC containing 
liquid mixture at each application location at the beginning and end of 
each test run. A separate sample should be taken of each VOC containing 
liquid added to the application mixture during the test run. If a fresh 
drum is needed during the sampling run, then obtain a sample from the 
fresh drum.
    4.1.2  When collecting the sample, ground the sample container to 
the coating drum. Fill the sample container as close to the rim as 
possible to minimize the amount of headspace.
    4.1.3  After the sample is collected, seal the container so the 
sample cannot leak out or evaporate.

[[Page 432]]

    4.1.4  Label the container to identify clearly the contents.
    4.2  Liquid sample VOC content.
    4.2.1  Assemble the liquid VOC content analysis system as shown in 
Figure 1.
    4.2.2  Permanently identify all of the critical orifices that may be 
used. Calibrate each critical orifice under the expected operating 
conditions (i.e., sample vacuum and temperature) against a volume meter 
as described in section 5.3.
    4.2.3  Label and tare the sample vessels (including the stoppers and 
caps) and the syringes.
    4.2.4  Install an empty sample vessel and perform a leak test of the 
system. Close the carrier gas valve and atmospheric vent and evacuate 
the sample vessel to 250 mm (10 in.) Hg absolute or less using the 
aspirator. Close the toggle valve at the inlet to the aspirator and 
observe the vacuum for at least one minute. If there is any change in 
the sample pressure, release the vacuum, adjust or repair the apparatus 
as necessary and repeat the leak test.
    4.2.5  Perform the analyzer calibration and linearity checks 
according to the procedure in section 5.1. Record the responses to each 
of the calibration gases and the back-pressure setting of the FIA.
    4.2.6  Establish the appropriate dilution ratio by adjusting the 
aspirator air supply or substituting critical orifices. Operate the 
aspirator at a vacuum of at least 25 mm (1 in.) Hg greater than the 
vacuum necessary to achieve critical flow. Select the dilution ratio so 
that the maximum response of the FIA to the sample does not exceed the 
high-range calibration gas.
    4.2.7  Perform system calibration checks at two levels by 
introducing compressed gases at the inlet to the sample vessel while the 
aspirator and dilution devices are operating. Perform these checks using 
the carrier gas (zero concentration) and the system calibration gas. If 
the response to the carrier gas exceeds 0.5 percent of span, 
clean or repair the apparatus and repeat the check. Adjust the dilution 
ratio as necessary to achieve the correct response to the upscale check, 
but do not adjust the analyzer calibration. Record the identification of 
the orifice, aspirator air supply pressure, FIA back-pressure, and the 
responses of the FIA to the carrier and system calibration gases.
    4.2.8  After completing the above checks, inject the system 
calibration gas for approximately 10 minutes. Time the exact duration of 
the gas injection using a stopwatch. Determine the area under the FIA 
response curve and calculate the system response factor based on the 
sample gas flow rate, gas concentration, and the duration of the 
injection as compared to the integrated response using Equations 2 and 
3.
    4.2.9  Verify that the sample oven and sample line temperatures are 
1205  deg.C and that the water bath temperature is 
1005  deg.C.
    4.2.10  Fill a tared syringe with approximately 1 g of the VOC 
containing liquid and weigh it. Transfer the liquid to a tared sample 
vessel. Plug the sample vessel to minimize sample loss. Weigh the sample 
vessel containing the liquid to determine the amount of sample actually 
received. Also, as a quality control check, weigh the empty syringe to 
determine the amount of material delivered. The two coating sample 
weights should agree within 0.02 g. If not, repeat the 
procedure until an acceptable sample is obtained.
    4.2.11  Connect the vessel to the analysis system. Adjust the 
aspirator supply pressure to the correct value. Open the valve on the 
carrier gas supply to the sample vessel and adjust it to provide a 
slight excess flow to the atmospheric vent. As soon as the initial 
response of the FIA begins to decrease, immerse the sample vessel in the 
water bath. (Applying heat to the sample vessel too soon may cause the 
FID response to exceed the calibrated range of the instrument, and thus 
invalidate the analysis.)
    4.2.12  Continuously measure and record the response of the FIA 
until all of the volatile material has been evaporated from the sample 
and the instrument response has returned to the baseline (i.e., response 
less than 0.5 percent of the span value). Observe the aspirator supply 
pressure, FIA back-pressure, atmospheric vent, and other system 
operating parameters during the run; repeat the analysis procedure if 
any of these parameters deviate from the values established during the 
system calibration checks in Section 4.2.7. After each sample perform 
the drift check described in Section 5.2. If the drift check results are 
acceptable, calculate the VOC content of the sample using the equations 
in Section 7. Integrate the area under the FIA response curve, or 
determine the average concentration response and the duration of sample 
analysis.

                  5. Calibration and Quality Assurance

    5.1  FIA calibration and linearity check. Make necessary adjustments 
to the air and fuel supplies for the FIA and ignite the burner. Allow 
the FIA to warm up for the period recommended by the manufacturer. 
Inject a calibration gas into the measurement system and adjust the 
back-pressure regulator to the value required to achieve the flow rates 
specified by the manufacturer. Inject the zero- and the high-range 
calibration gases and adjust the analyzer calibration to provide the 
proper responses. Inject the low- and mid-range gases and record the 
responses of the measurement system. The calibration and linearity of 
the system are acceptable if the responses for all four gases are within 
5 percent of the respective gas

[[Page 433]]

values. If the performance of the system is not acceptable, repair or 
adjust the system and repeat the linearity check. Conduct a calibration 
and linearity check after assembling the analysis system and after a 
major change is made to the system.
    5.2  Systems drift checks. After each sample, repeat the system 
calibration checks in Section 4.2.7 before any adjustments to the FIA or 
measurement system are made. If the zero or calibration drift exceeds 
3 percent of the span value, discard the result and repeat 
the analysis.
    5.3  Critical orifice calibration.
    5.3.1  Each critical orifice must be calibrated at the specific 
operating conditions that it will be used. Therefore, assemble all 
components of the liquid sample analysis system as shown in Figure 3. A 
stopwatch is also required.
    5.3.2 Turn on the sample oven, sample line, and water bath heaters 
and allow the system to reach the proper operating temperature. Adjust 
the aspirator to a vacuum of 380 mm (15 in.) Hg vacuum. Measure the time 
required for one soap bubble to move a known distance and record 
barometric pressure.
    5.3.3 Repeat the calibration procedure at a vacuum of 406 mm (16 
in.) Hg and at 25-mm (1-in.) Hg intervals until three consecutive 
determinations provide the same flow rate. Calculate the critical flow 
rate for the orifice in ml/min at standard conditions. Record the vacuum 
necessary to achieve critical flow.

                             6. Nomenclature

AL=area under the response curve of the liquid sample, area 
          count.
AS=area under the response curve of the calibration gas, area 
          count.
CS=actual concentration of system calibration gas, ppm 
          propane.
K=1.830 x 10-9 g/(ml-ppm).
L=total VOC content of liquid input, kg.
ML=mass of liquid sample delivered to the sample vessel, g.
q=flow rate through critical orifice, ml/min.
RF=liquid analysis system response factor, g/area count.
TS=total gas injection time for system calibration gas during 
          integrator calibration, min.
VFj=final VOC fraction of VOC containing liquid j.
VIj=initial VOC fraction of VOC containing liquid j.
VAj=VOC fraction of VOC containing liquid j added during the 
          run.
V=VOC fraction of liquid sample.
WFj=weight of VOC containing liquid j remaining at end of the 
          run, kg.
WIj=weight of VOC containing liquid j at beginning of the 
          run, kg.
WAj=weight of VOC containing liquid j added during the run, 
          kg.

                             7. Calculations

    7.1 Total VOC content of the input VOC containing liquid.
    [GRAPHIC] [TIFF OMITTED] TC07NO91.027
    
    7.2 Liquid sample analysis system response factor for systems using 
intergrators, grams/area counts.
[GRAPHIC] [TIFF OMITTED] TC07NO91.028

    7.3 VOC content of the liquid sample.
    [GRAPHIC] [TIFF OMITTED] TC07NO91.029
    
      

[[Page 434]]

[GRAPHIC] [TIFF OMITTED] TC01MY92.102



[[Page 435]]

[GRAPHIC] [TIFF OMITTED] TC01MY92.103



[[Page 436]]

[GRAPHIC] [TIFF OMITTED] TC01MY92.104



[[Page 437]]

 Procedure T--Criteria for and Verification of a Permanent or Temporary 
                             Total Enclosure

                             1. Introduction

    1.1  Applicability. This procedure is used to determine whether a 
permanent or temporary enclosure meets the criteria of a total 
enclosure.
    1.2  Principle. An enclosure is evaluated against a set of criteria. 
If the criteria are met and if all the exhaust gases are ducted to a 
control device, then the volatile organic compounds (VOC) capture 
efficiency (CE) is assumed to be 100 percent and CE need not be 
measured. However, if part of the exhaust gas stream is not ducted to a 
control device, CE must be determined.

                             2. Definitions

    2.1  Natural Draft Opening (NDO)--Any permanent opening in the 
enclosure that remains open during operation of the facility and is not 
connected to a duct in which a fan is installed.
    2.2  Permanent Total Enclosure (PTE)--A permanently installed 
enclosure that completely surrounds a source of emissions such that all 
VOC emissions are captured and contained for discharge through a control 
device.
    2.3  Temporary Total Enclosure (TTE)--A temporarily installed 
enclosure that completely surrounds a source of emissions such that all 
VOC emissions are captured and contained for discharge through ducts 
that allow for the accurate measurement of VOC rates.

               3. Criteria of a Temporary Total Enclosure

    3.1  Any NDO shall be at least 4 equivalent opening diameters from 
each VOC emitting point.
    3.2  Any exhaust point from the enclosure shall be at least 4 
equivalent duct or hood diameters from each NDO.
    3.3  The total area of all NDO's shall not exceed 5 percent of the 
surface area of the enclosure's four walls, floor, and ceiling.
    3.4  The average facial velocity (FV) of air through all NDO's shall 
be at least 3,600 m/hr (200 fpm). The direction of air through all NDO's 
shall be into the enclosure.
    3.5  All access doors and windows whose areas are not included in 
section 3.3 and are not included in the calculation in section 3.4 shall 
be closed during routine operation of the process.

               4. Criteria of a Permanent Total Enclosure

    4.1  Same as sections 3.1 and 3.3-3.5.
    4.2  All VOC emissions must be captured and contained for discharge 
through a control device.

                              5. Procedure

    5.1  Determine the equivalent diameters of the NDO's and determine 
the distances from each VOC emitting point to all NDO's. Determine the 
equivalent diameter of each exhaust duct or hood and its distance to all 
NDO's. Calculate the distances in terms of equivalent diameters. The 
number of equivalent diameters shall be at least 4.
    5.2  Measure the total area (At) of the enclosure and the 
total area (AN) of all NDO's of the enclosure. Calculate the 
NDO to enclosure area ratio (NEAR) as follows:

NEAR=AN/At
    The NEAR must be 0.05.
    5.3  Measure the volumetric flow rate, corrected to standard 
conditions, of each gas stream exiting the enclosure through an exhaust 
duct or hood using EPA Method 2. In some cases (e.g., when the building 
is the enclosure), it may be necessary to measure the volumetric flow 
rate, corrected to standard conditions, of each gas stream entering the 
enclosure through a forced makeup air duct using Method 2. Calculate FV 
using the following equation:

FV=[QO - QI]/AN

where:

QO=the sum of the volumetric flow from all gas streams 
          exiting the enclosure through an exhaust duct or hood.
QI=the sum of the volumetric flow from all gas streams into 
          the enclosure through a forced makeup air duct; zero, if there 
          is no forced makeup air into the enclosure.
AN=total area of all NDO's in enclosure.

    The FV shall be at least 3,600 m/hr (200 fpm).
    5.4  Verify that the direction of air flow through all NDO's is 
inward. Use streamers, smoke tubes, tracer gases, etc. Strips of plastic 
wrapping film have been found to be effective. Monitor the direction of 
air flow at intervals of at least 10 minutes for at least 1 hour.

                          6. Quality Assurance

    6.1  The success of this protocol lies in designing the TTE to 
simulate the conditions that exist without the TTE, i.e., the effect of 
the TTE on the normal flow patterns around the affected facility or the 
amount of fugitive VOC emissions should be minimal. The TTE must enclose 
the application stations, coating reservoirs, and all areas from the 
application station to the oven. The oven does not have to be enclosed 
if it is under negative pressure. The NDO's of the temporary enclosure 
and a fugitive exhaust fan must be properly sized and placed.
    6.2  Estimate the ventilation rate of the TTE that best simulates 
the conditions that exist without the TTE, i.e., the effect of the TTE 
on the normal flow patterns around the affected facility or the amount 
of fugitive

[[Page 438]]

VOC emissions should be minimal. Figure 1 may be used as an aid. Measure 
the concentration (CG) and flow rate (QG) of the 
captured gas stream, specify a safe concentration (CF) for 
the fugitive gas stream, estimate the CE, and then use the plot in 
Figure 1 to determine the volumetric flowrate of the fugitive gas stream 
(QF). A fugitive VOC emission exhaust fan that has a variable 
flow control is desirable.
    6.2.1  Monitor the concentration of VOC into the capture device 
without the TTE. To minimize the effect of temporal variation on the 
captured emissions, the baseline measurement should be made over as long 
a time period as practical. However, the process conditions must be the 
same for the measurement in section 6.2.3 as they are for this baseline 
measurement. This may require short measuring times for this quality 
control check before and after the construction of the TTE.
    6.2.2  After the TTE is constructed, monitor the VOC concentration 
inside the TTE. This concentration shall continue to increase and must 
not exceed the safe level according to OSHA requirements for permissible 
exposure limits. An increase in VOC concentration indicates poor TTE 
design or poor capture efficiency.
    6.2.3  Monitor the concentration of VOC into the capture device with 
the TTE. To limit the effect of the TTE on the process, the VOC 
concentration with and without the TTE must be within 10 
percent. If the measurements do not agree, adjust the ventilation rate 
from the TTE until they agree within 10 percent.


[[Page 439]]

[GRAPHIC] [TIFF OMITTED] TC01MY92.105



[55 FR 26856, June 29, 1990; 55 FR 31981, Aug. 6, 1990; 55 FR 39774, 
39775, Sept. 28, 1990, as amended at 56 FR 24723, May 31, 1991; 56 FR 
33712, July 23, 1991; 57 FR 3946, Feb. 3, 1992; 57 FR 7550, Mar. 3, 
1992; 57 FR 27936, June 23, 1992; 58 FR 31653, June 4, 1993; 58 FR 
34908, June 30, 1993; 59 FR 14112, Mar. 25, 1994; 59 FR 46569, Sept. 9, 
1994; 60 FR 41, Jan. 3, 1995; 60 FR 13045, Mar. 10, 1995; 60 FR 14900, 
Mar. 21, 1995; 60 FR 43387, 43393, 43395, Aug. 21, 1995; 61 FR 54559, 
Oct. 21, 1996]

[[Page 440]]



Sec. 52.742  Incorporation by reference.

    The materials listed below are incorporated by reference in the 
corresponding sections noted. The incorporation by reference was 
approved by the Director of the Office of Federal Register in accordance 
with 5 U.S.C. 552(a) and 1 CFR part 51. These materials are incorporated 
as they exist on the date of approval, and a notice of any change in 
these materials will be published in the Federal Register. The materials 
are available from the sources listed below.
    (a) The following material is available for purchase from the 
American Society for Testing and Materials (ASTM), 1916 Race Street, 
Philadelphia, PA 19103.

    (1) ASTM D1475-85, Standard Test Method for Density of Paint, 
Varnish, Lacquer, and Related Products, for 
Sec. 52.741(a)(4)(i)(B)(3)(i).
    (2) ASTM D2369-87, Standard Test Method for Volatile Content of 
Coatings, for Sec. 52.741(a)(4)(i)(B)(3)(ii).
    (3) ASTM D3792-86, Standard Test Method for Water Content of Water-
Reducible Paints by Direct Injection into a Gas Chromatograph, for 
Sec. 52.741(a)(4)(i)(B)(3)(iii).
    (4) ASTM D4017-81(Reapproved 1987), Standard Test Method for Water 
in Paints and Paint Materials by Karl Fischer Method, for 
Sec. 52.741(a)(4)(i)(B)(3)(iv).
    (5) ASTM D4457-85, Standard Test Method for Determination of 
Dichloromethane and 1,1,1-Trichloroethane in Paints and Coatings by 
Direct Injection into a Gas Chromatograph, for 
Sec. 52.741(a)(4)(i)(B)(3)(v).
    (6) ASTM D2697-86, Standard Test Method for Volume Nonvolatile 
Matter in Clear or Pigmented Coatings, for 
Sec. 52.741(a)(4)(i)(B)(3)(vi).
    (7) ASTM D3980-87, Standard Practice for Interlaboratory Testing of 
Paint and Related Materials, for Sec. 52.741(a)(4)(i)(B)(3)(vi).
    (8) ASTM E180-85, Standard Practice for Determining the Precision of 
ASTM Methods for Analysis and Testing of Industrial Chemicals, for 
Sec. 52.741(a)(4)(i)(B)(3)(viii).
    (9) ASTM D2372-85, Standard Method of Separation of Vehicle from 
Solvent-Reducible Paints, for Sec. 52.741(a)(4)(i)(B)(3)(ix).
    (10) ASTM D2879-86, Standard Test Method for Vapor Pressure-
Temperature Relationship and Initial Decomposition Temperature of 
Liquids by Isoteniscope, for Sec. 52.741(a)(3), (a)(8)(ii), (a)(9)(iii), 
and (a)(10)(iii).
    (11) ASTM D323-82, Standard Test Method for Vapor Pressure of 
Petroleum Products (Reid Method), for Sec. 52.741(a)(3).
    (12) ASTM D86-82, Standard Method for Distillation of Petroleum 
Products, for Sec. 52.741(a)(3).
    (13) ASTM D3925-81(Reapproved 1985), Standard Practice for Sampling 
Liquid Paints and Related Pigment Coatings, for 
Sec. 52.741(a)(4)(i)(A)(1).
    (14) ASTM E300-86, Standard Practice for Sampling Industrial 
Chemicals, for Sec. 52.741(a)(4)(i)(A)(2).

    (b) The Evaporation Loss From External Floating-Roof Tanks, 
Publication 2517, second edition, February 1980, for Sec. 52.741(a)(3) 
is available for purchase from the American Petroleum Institute, 2101 L 
Street, NW., Washington, DC 20037.
    (c) The Standard Industrial Classification Manual, 1987, for 
Sec. 52.741(a)(3) is available for purchase from the Superintendent of 
Documents, U.S. Government Printing Office, Washington, DC 20402.
    (d) 35 Illinois Administrative Code 215, June 1989, subparts (B), 
(E) (sections 215.182, 215.183, and 215.184), (K) (sections 215.301 and 
215.302), (Q) (excluding sections 215.432 and 215.436), (R) (excluding 
sections 215.447, 215.450, and 215.452), (S), (V), (X), (Y) (sections 
215.582, 215.583, and 215.584), and (Z) of 35 Ill. Adm. Code 215 for 
Sec. 52.741 (d)(l)-(d)(3); (e)(3), (e)(4); (h)(2); (i)(1), (i)(2); 
(j)(1)-(j)(3); (q)(1); (s)(1); (u)(1), (3); (v)(1); (w)(1); and (x)(1), 
(x)(3) is available from the United States Environmental Protection 
Agency, Air and Radiation Division, Region V, 230 S. Dearborn, Chicago, 
IL, 60604.
[55 FR 26909, June 29, 1990]



Sec. 52.743  Continuous monitoring.

    (a) Alternative monitoring requirements established under Section 
201.402 of Title 35, IAC must be either: Incorporated into a federally 
enforceable operating permit or construction permit or submitted to 
USEPA for approval as a revision to the Illinois State Implementation 
Plan (SIP). Illinois shall set forth alternative emissions monitoring 
and reporting requirements to satisfy the intent of 40 CFR part 51, 
appendix P whenever Illinois exempts any source subject to Section 
201.401 from installing continuous emission monitoring systems. Illinois 
may exempt a source if the source cannot install a continuous emission 
monitoring system because of physical plant limitations or extreme 
economic reasons, according to the criteria of Section 201.402.

[[Page 441]]

    (b) As codified at 40 CFR 52.737 (USEPA's approval of the Illinois 
operating permit program for the purpose of issuing federally 
enforceable construction and operating permits), USEPA reserves the 
right to deem an operating permit not federally enforceable. Such a 
determination will be made according to appropriate procedures including 
operating permit requirements promulgated at 54 FR 27274 (June 28, 1989) 
and will be based upon either; the permit, permit approval procedures or 
state or local permit requirements which do not conform with the 
operating permit program requirements or the requirements of USEPA's 
underlying regulations. Among other things, underlying requirements 
include 40 CFR 51.214 and part 51, appendix P and Illinois' approved 
SIP, 40 CFR part 52. Should USEPA deem an operating or construction 
permit containing alternative monitoring requirements not federally 
enforceable, the underlying continuous monitoring requirements at 
Section 201.401 of the State rule would be the Federal requirements 
contained in the SIP to which the source would be subject. This 
interpretation of the impact of an operating permit deemed not federally 
enforceable by USEPA on a source to which it was issued was acknowledged 
by the State in a March 3, 1993, letter from Bharat Mathur, Chief, 
Bureau of Air, Illinois Environmental Protection Agency, to Stephen 
Rothblatt, Chief, Regulation Development Branch, Region 5, USEPA.
[58 FR 17783, Apr. 6, 1993]



Sec. 52.744  Small business stationary source technical and environmental compliance assistance program.

    The Illinois program submitted on November 12, 1992, as a requested 
revision to the Illinois State Implementation Plan satisfies the 
requirements of section 507 of the Clean Air Act Amendments of 1990.
[58 FR 45451, Aug. 30, 1993]



                           Subpart P--Indiana



Sec. 52.769  Identification of plan--conditional approval.

    The plan revision commitment listed in paragraphs (a) and (b) of 
this section were submitted on the dates specified.
    (a)  [Reserved]
    (b) On February 25, 1994, Indiana submitted an amendment to Title 
326 of the Indiana Administrative Code (326 IAC) 8-5-5 to add Volatile 
Organic Compound (VOC) Reasonably Available Control Technology (RACT) 
requirements for graphic arts facilities in the Indiana severe ozone 
nonattainment area (Lake and Porter Counties) which have the potential 
to emit 25 tons per year or more of VOC. The United States Environmental 
Protection Agency (USEPA) is conditionally approving the State's graphic 
arts facilities VOC RACT rule, contingent on fulfillment of the State's 
commitment to adopt and submit a State Implementation Plan (SIP) 
revision that would correct deficiencies in the State's recordkeeping 
and reporting requirements, contained in 326 IAC 8-1-2, by May 6, 1996. 
In order to correct the deficiencies, the State must meet three 
requirements.
    The first requirement is for the monitoring, recordkeeping and 
reporting (MRR) requirements in the Indiana rules to be made more 
comprehensive to include more than: Daily volume-weighted averages of 
all coatings applied in a coating or printing line; and records of daily 
usage of gallons of solids coating and VOC content for each coating or 
ink solvent. Alternatively, when a source complies by using control 
devices, then records of monitoring parameters and other information 
must also be kept. The MRR requirements should also specify a period of 
time (i.e., 5 years) during which records shall be maintained at the 
facility. The second requirement is for the Indiana rules to be revised 
to require maintenance of records and reports of new or existing control 
devices. Records and reports that should be maintained include 
monitoring data, calibration and

[[Page 442]]

maintenance logs, and logs of operating time. The third requirement is 
for the Indiana rules to be revised to require the maintenance of 
records and reports for exempt sources such as: Information pertaining 
to the initial certification, calculations demonstrating that total 
potential emissions of VOC from all flexographic and rotogravure 
printing presses at the facility will be less than the required limits 
for each year, the maintenance of record for a period of 5 years, and 
the requirement that any exceedance will be reported to the 
Administrator within 30 days after the exceedance occurs. Exempt sources 
should calculate: Yearly potential emissions, yearly actual emissions, 
and the name, identification, VOC content, and yearly volume of 
coatings/inks. If the State ultimately fails to meet its commitment to 
meet these requirements by the date listed above, then USEPA's action 
for the State's requested SIP revision will automatically convert to a 
final disapproval without further regulatory action.
    (1) Incorporation by reference.
    (i) (A) 326 IAC 8-5-5 Graphic arts operations. Filed with the 
Secretary of State, August 9, 1993, effective September 8, 1993, 
Published at Indiana Register, Volume 16, Number 12, September 1, 1993.
[60 FR 22241, 22242, May 4, 1995, as amended at 62 FR 19056, Apr. 18, 
1997; 63 FR 35144, June 29, 1998]

    Effective Date Note:  At 63 FR 35144, June 29, 1998, Sec. 52.769 was 
amended by removing and reserving paragraph (b), effective Aug. 28, 
1998.



Sec. 52.770  Identification of plan.

    (a) Title of plan: ``State of Indiana Air Pollution Control 
Implementation Plan.''
    (b) The plan was officially submitted on January 31, 1972.
    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) The State Air Pollution Control Board submitted a SO2 
control strategy for the City of Indianapolis on March 16, 1972.
    (2) The Governor submitted Pub. L. 100, Regulation APC 12-R and 13 
through 17 on April 11, 1972.
    (3) On May 1, 1972, the Governor's office submitted an errata sheet 
and revised pages for the State plan.
    (4) A request for a nine month extension to achieve secondary 
SO2 standards in the Indianapolis Region was made by the 
Governor on May 16, 1972.
    (5) The State Air Pollution Control Board submitted additional 
information on surveillance methodology (non-regulatory) on May 17, 
1972.
    (6) Regulation APC 4-R was transmitted by the Governor on June 30, 
1972.
    (7) Assurance that emission data for sources was available for 
public inspection was given on July 24, 1972, by the Technical Secretary 
to the Indiana Board.
    (8) Clarification of a policy on availability of emission data to 
the public sent August 17, 1972, by the Technical Secretary to the 
Indiana Board.
    (9) On September 15, 1972, amendments to State control regulations 
13, 15 and 16 were submitted to the Governor.
    (10) On May 8, 1973, the Governor submitted a new regulation (APC-
19) which replaced APC-1.
    (11) The Governor submitted a transportation control plan for Marion 
County on October 19, 1973.
    (12) On March 7, 1974, the Technical Secretary of the Air Pollution 
Control Board, acting for the Governor of Indiana, submitted new 
regulation APC-20.
    (13) On October 3, 1974, the Technical Secretary submitted revised 
regulations APC-16 covering CO, APC-17 covering NO2 and a new 
regulation APC-22 covering classification of counties for 
SO2, oxidants, particulates, NO2 and CO.
    (14) On November 8, 1974, the Technical Secretary submitted revised 
regulation APC-3 covering visible emissions and revised regulation APC-
15 covering hydrocarbons.
    (15) On December 5, 1974, the Technical Secretary submitted revised 
regulation APC-13 covering SO2. On July 18, 1975, an updated 
Technical Support Document on APC-13 was submitted by the Technical 
Secretary.
    (16) On June 14, 1976, the Technical Secretary submitted enforcement 
orders varying the final sulfur dioxide emission limitations for the 
Warrick

[[Page 443]]

and Culley electrical generating stations in Warrick County.
    (17) On March 16, 1977, the Technical Secretary submitted new 
regulation APC-8, Continuous Emission Monitoring; and revised 
regulations APC-7, Incinerators; and APC-14, Indiana Ambient Air Quality 
Standards.
    (18) On May 18, 1977, the Technical Secretary submitted revised 
regulation APC-2, Open Burning.
    (19) On June 26, 1979, the Governor submitted a revised sulfur 
dioxide strategy, including regulation APC 13 with appendix, which was 
promulgated by the State on June 19, 1979 for all areas of the State. 
This included the Part D sulfur dioxide regulations for Lake, LaPorte, 
and Marion Counties. On August 27, 1980 and July 16, 1981 the State 
committed itself to correct conditionally approved items within their 
strategy. On October 6, 1980, the State submitted a recodified version 
of APC 13 which was promulgated by the State on August 27, 1980. This 
included 325 IAC 7, 325 IAC 1.1-6, 325 IAC 1.1-7-2 and 4, 325 IAC 12-5-1 
and 2(a), 325 IAC 12-9-1 and 4, and 325 IAC 12-18-1 and 2. EPA is not 
taking action on: (i) 325 IAC 7 as it applies to Floyd and Vigo 
Counties, (ii) the 30-day averaging compliance method contained in 325 
IAC 7-1-3, and (iii) the stack height provision for NIPSCO's Mitchell 
Station in the Lake County SO2 strategy and (4) the stack 
height provisions for IPALCO's Stout Generating Chemicals Company, and 
Detroit Diesel Allison's Plant 8 in the Marion County SO2 
strategy.
    (20) On June 26, 1979, the State of Indiana submitted to EPA 
revisions to the ozone and carbon monoxide portions (section 3.3.24) of 
its Marion County State Implementation Plan. On March 11, 1980, the 
state submitted revisions to the Marion County technical appendix to 
section 3.3.24. On May 19, 1980, the state submitted ozone and carbon 
monoxide attainment demonstrations for Marion County (section 1.5). On 
September 8, 1980 the state submitted its memoranda of understanding. On 
October 9 and October 15, 1980, the state submitted documentation 
concerning interagency coordination and the analysis of transportation 
control measures. On January 7, 1981, the state submitted corrections 
and clarifications in response to EPA's notice of proposed rulemaking 
(45 FR 81070).
    (21) On June 26, 1979 Indiana submitted a motor vehicle inspection 
and maintenance program for Clark, Floyd, Lake, and Porter Counties. 
Additional commitments were submitted on April 7, 1980; June 12, 1980; 
August 27, 1980; November 13, 1980 and November 24, 1980.
    (22) On June 26, 1979, Indiana made submittals pertaining to section 
121 Consultation, section 110(a)(2)(K)--Permit Fees, section 126--
Interstate Pollution, section 127--Public Notification, section 128--
State Boards and section 110(a)(2)(F) (ii) and (iii)--Continuous 
Emission Monitoring Additional commitments were secured on April 17, 
1980, June 25, 1980, August 1, 1980, November 10, 1980, December 9, 
1980, and December 31, 1980. A revised version of Indiana's continuous 
emission monitoring regulation (325 IAC 3) was submitted on October 6, 
1980.
    (23) On June 26, 1979, the State of Indiana submitted a revision to 
provide for modification of the existing air quality surveillance 
network.
    (24) On June 26, 1979, the Governor submitted a revised new source 
review regulation, APC-19. Additional information and commitments were 
submitted on June 25, 1980 and May 19, 1981. EPA is not taking action on 
section 7 of APC-19, Prevention of Significant deterioration.
    (25) On June 26, 1979 the Governor submitted revised emission limits 
for Knauf Fiberglass, Shelby County. Additional information was 
submitted by November 21, 1979. The emission limitations were recodified 
as 325 IAC 11-4 and 11-4 Appendix A and were resubmitted on October 6, 
1980.
    (26) On June 26, 1979 the Governor submitted Indiana's definition 
regulation, APC-1. The definitions were recodified as 325 IAC 1.1-1 and 
resubmitted on October 6, 1980. On January 21, 1981 Indiana submitted a 
revised definition for ``positive net air quality benefit.'' EPA is 
taking no action on 325 IAC 1.1-1-82, definition of ``State 
Implementation Plan (SIP).''

[[Page 444]]

    (27) On October 6, 1980, Indiana submitted Regulation 325 IAC 1.1-2 
(formerly APC 14) which includes the primary and secondary ambient air 
quality standards for ozone and lead.
    (28) On February 26, 1981, Indiana submitted a revision to its plan 
waiving the State's sulfur dioxide air monitoring requirement of section 
4(a) of Regulation 325 IAC 7-1 for the area around Public Service of 
Indiana's Noblesville Generating Station.
    (29) On June 26, 1979, May 19, 1980, September 24, 1980, October 9, 
1980 and October 15, 1980, Indiana submitted transportation control 
plans and ozone demonstrations of attainment for Lake, Porter, Clark, 
Floyd, St. Joseph, Elkhart and Allen Counties. It also submitted a 
carbon monoxide demonstration of attainment for Lake County. EPA is 
taking no action on the ozone demonstration of attainment for St. 
Joseph, Elkhart and Allen Counties.
    (30) On April 10, 1981, Indiana submitted revised emission limits 
for Indiana Farm Bureau Cooperative Association's Beech Grove plant.
    (31) On February 11, 1980, Indiana submitted a revised sulfur 
dioxide strategy for Vigo County. Technical information was submitted on 
December 10, 1979 and on May 30, 1980. On October 6, 1980, the State 
submitted a recodified version of the Vigo County Regulations, 325 IAC 
Article 7, which was promulgated by the State on August 27, 1980. EPA is 
not taking action on the 30-day averaging compliance method contained in 
325 IAC 7-1-3 as it applies to Vigo County.
    (32) On November 24, 1981, Indiana submitted site specific emission 
limitations for Tecumseh Pipe Line Company, Schererville; and Wayne 
Transportation Division, Richmond.
    (33) On February 11, 1980, Indiana submitted APC 15. EPA is taking 
no action the ``bubble'' provisions contained in Section 8(a)(2) of 
revised APC 15.
    (34) On June 26, 1979, the Governor of Indiana submitted general TSP 
RACT emisson limits for nonattainment areas. These regulations were 
amended and recodified as 325 IAC 6-1 and resubmitted on October 6, 
1980. On October 6, 1980, the State submitted a revised TSP regulation 
for process sources, 325 IAC 6-3; a source specific Dearborn County 
strategy (amendments were submitted on August 10, 1981), 325 IAC 6-1-8; 
a source specific Dubois County strategy, 325 IAC 6-1-9; and a source 
specific Wayne County strategy (amendments were submitted on January 29, 
1981), 325 IAC 6-1-14. On February 11, 1980, Indiana submitted a source 
specific Marion County strategy (amendments were submitted on October 
28, 1981), 325 IAC 6-1-12. EPA is deferring rulemaking at this time on 
the coke battery emission limitations in the Marion County strategy. On 
January 29, 1981, the State submitted a source specific Vigo County 
strategy (amendments were submitted on October 28, 1981 and May 7, 
1982), 325 IAC 6-1-13; a source specific Howard County strategy, 325 IAC 
6-1-15; and a source specific Vanderburgh County strategy (amendments 
were submitted on October 28, 1981), 325 IAC 6-1-16. EPA is deferring 
rulemaking at this time on the coke battery emission limitations in the 
Vigo County strategy and on whether the Howard County strategy currently 
contains all the elements required by the Clean Air Act. On July 8, 
1981, the State submitted a source specific Clark County strategy, 325 
IAC 6-1-17, and a source specific St. Joseph County strategy, 325 IAC 6-
1-18. On January 29, 1981 and May 7, 1982, the State submitted 
additional information and commitments.
    (35) On October 6, 1980, Indiana submitted its regulations as 
recodified. Amendments were submitted on January 29, 1981 and March 18, 
1981. EPA's approval is directed specifically to the codification 
numbering system change, not to the substance within each of the 
codified rules.
    (36) [Reserved]
    (37) On May 10, 1982, Indiana submitted source specific emission 
limits contained in operating permits for the Bunge Corporation, Globe 
Industries, Skyline Corporation, and Dubois County Farm Bureau Co-op 
Assn., Inc. as revisions to the Indiana SIP.
    (38) On April 27, 1982, Indiana submitted source specific TSP 
emission limits for Huntingburg Wood Products, Jasper Desk Company, 
Jasper Office Furniture Company, Arist-O-Kraft Company, Mohr 
Construction Company, Dana

[[Page 445]]

Corporation, and Allis Chalmers Corporation. On April 29, 1982, Indiana 
submitted source specific VOC emission limits for McGee Refining 
Corporation, Hesco Industries, and Clark Oil and Refining Corporation.
    (39) On November 25, 1980, Indiana submitted 325 IAC Article 8, 
Volatile Organic Compound Regulations. This regulation adds Group II CTG 
requirements to Indiana's VOC plan and was State promulgated on October 
15, 1980. EPA is not taking action on 325 IAC 8-1.1 Section 2(b), Bubble 
Approach.
    (40) On November 24, 1981, Indiana submitted site specific emission 
limitations for Jeffboat, Inc., Jeffersonville.
    (41) On November 23, 1982, Indiana submitted source-specific 
emission limits for Paul H. Rohe Company, Inc.
    (42) On June 26, 1979, Indiana submitted its coke oven battery 
regulation, APC 9. On October 6, 1980 Indiana resubmitted this 
regulation recodified as 325 IAC 11-3. On August 27, 1981, Indiana 
submitted amendments to 325 IAC 11-3. EPA is taking no action on 325 IAC 
11-3-2(a), Pre-Carbonization Emissions. It is taking no action on 325 
IAC 11-3-2(i), Underfire Particulate and Sulfur Dioxide Emissions, as it 
applies to Lake County.
    (43) On February 26, 1981 and June 22, 1982, Indiana submitted a 
9.57 lbs/MMBTU sulfur dioxide emission limit for IMEC's Breed Generating 
Station in Sullivan County. This limit supersedes that approved at 
paragraph (c)(19).
    (44) On June 28, 1982, Indiana submitted new open burning 
regulations for Marion County. An amendment was submitted on August 25, 
1982.
    (45) On March 15, 1983, Indiana submitted a revision to the TSP and 
SO2 portions of its SIP in the form of operating permits for 
the Sisters of Providence Convent in St. Mary-of-the-Woods, Indiana.
    (46) On November 29, 1982, and December 9, 1982, Indiana submitted 
amendments to 325 IAC 11-4, Fiber Glass Insulation Manufacturing 
(Superfine Process) Limitations.
    (47) On August 17, 1983, Indiana submitted emission limits of 1.8 
lbs/hr and 2.4 tons/yr for the boilers at Jasper Cabinet Co., Dubois 
County. The 1.8 lbs/hr limit replaces the 7.6 lbs/hr limit approved for 
this source in subparagraph 34.
    (48) [Reserved]
    (49) On March 28, 1983, Indiana submitted a 20% 2-hour opacity limit 
as an ``equivalent visible emission limit'' (EVEL) for the underfire 
stack at Bethlehem Steel Corporation's Coke Battery No. 2 in Porter 
County. This EVEL is approved for as long as the SIP mass emission limit 
determined from 325 IAC 6-2 (October 6, 1980, submittal) for this source 
remains in the SIP See (c)(6), (35), and (42).
    (50) On December 21, 1983, the Indiana Air Pollution Control Board 
submitted Indiana Rule 325 IAC 6-2.1, Particulate Emission Limitations 
for Sources of Indirect Heating. This rule repeals and replaces Indiana 
Rule 325 IAC 6-2. See Secs. 52.770(c)(4) and (c)(35) and Sec. 52.776(i).
    (i) Incorporation by reference.
    (A) 325 IAC 6-2.1, revised regulation establishing Particulate 
Emission Limitations for Sources of Indirect Heating.
    (ii) Additional material.
    (A) December 21, 1983, submittal of Finding of Facts and 
Recommendations of Hearing Officer R. W. James on 325 IAC 6-2.1.
    (B) March 27, 1985, commitment letter from the State concerning the 
procedures the State will use in processing ``bubbles'' under 325 IAC 6-
2.1-2(B) and 3(b). See Sec. 52.776(i).
    (51) On February 7, 1983, Indiana submitted revised opacity limits 
for existing boilers at Olin Corporation, located in Covington, Indiana. 
These ``equivalent visible emission limits'' (EVEL) are approved for as 
long as the SIP mass emission limit determined from 325 IAC 6-2 (October 
6, 1980 submittal) for this source remains in the SIP. See 
Sec. 52.770(c) (6) and (35) and Sec. 52.776(h)(2).
    (i) Incorporation by reference.
    (A) EVELs for Olin Corporation contained in Operating Permits issued 
by IAPCB, dated October 6, 1981.
    (ii) Additional material.
    (A) September 1, 1983, transmittal by IAPCD's A. Sunderland of 
Olin's Mass Emission Tests, dated August 26, 1983.
    (B) April 5, 1984, letter from IAPCD's E. Stresino transmitting 
original petition, including Method 9 opacity data.
    (52) On February 23, 1984, the Indiana Air Pollution Control Board 
submitted

[[Page 446]]

a revision to Indiana's SO2 SIP waiving the self-monitoring 
requirement for Public Service Indiana's Edwardsport Generating Station, 
as set forth in section 4(a) of Rule 325 IAC 7-1. See (c)(19). This 
revision becomes effective once the Edwardsport Station achieves an 
annual operating capacity of no greater than 10%.
    (53) On October 6, 1980, Indiana submitted revised opacity 
regulation 325 IAC 5-1. It replaces 1972 APC 3 for process sources, 
approved at paragraph (b), and SIP 1974 APC 3 for combustion sources, 
approved in part at subparagraph (c)(14). Indiana does not intend 325 
IAC 5-1 to regulate the emission points in Lake County listed in Table 2 
of 325 IAC 6-1-110.2 (subparagraph (c)(57)). USEPA is disapproving 325 
IAC 5-1 for these sources. Indiana does not intend 325 IAC 5-1 to 
regulate certain coke battery emission sources listed in 325 IAC 11-3 
(subparagraph (c)(42)). USEPA is disapproving 325 IAC 5-1 as it applies 
to the provisions of 325 IAC 11-3 which USEPA disapproved at (c)(42), 
i.e., pushing and quenching sources throughout the State and coke oven 
doors in Lake and Marion Counties. Additionally, Indiana has modified 
325 IAC 5-1 as it applies to the stack emission points in Porter County 
listed at 325 IAC 6-6-4. USEPA disapproved 325 IAC 5-1 as it applies to 
these Porter County sources on February 5, 1987 (52 FR 3640). For those 
source categories where USEPA is disapproving 325 IAC 5-1, they remain 
regulated by the previously approved opacity SIP which consists of SIP 
1974 APC 3 for combustion sources and 1972 APC 3 for process sources. 
Additionally, as long as the Bethlehem Steel Corporation No. 2 Coke Oven 
Battery Underfire Stack EVEL (subparagraph (c)(49)) remains approved, it 
replaces 325 IAC 5-1.
    (i) Incorporation by reference.
    (A) A letter dated October 6, 1980 from the State of Indiana Air 
Pollution Control Board and 325 IAC 5-1, Visible Emission Limitations, 
State promulgated on August 26, 1980.
    (ii) Additional material.
    (A) February 12, 1985, letter from the Technical Secretary of the 
Air Pollution Control Board committing the State to make certain 
technical changes to 325 IAC 5-1.
    (54) On March 28, 1984, Indiana submitted a revised TSP emission 
limitation for Richmond State Hospital, Wayne County, Indiana. This 
limitation replaces the one in 325 IAC 6-1-14 which was previously 
approved at (c)(34).
    (i) Incorporation by reference.
    (A) On January 13, 1984, Indiana issued to Richmond State Hospital 
an amendment to operating permit, 89-04-85-0153, which revised its TSP 
emission limitations for the four boilers to 0.60 lbs/MMBTU with an 
annual total limit of 452 tons/yr.
    (55) On January 30, 1985, Indiana submitted revised VOC regulations 
325 IAC 8-1.1, 8-2, 8-3, 8-4 and 8-5 to satisfy certain conditions of 
USEPA's approval. Those regulations amended those approved at (c)(33) 
and (c)(34). In addition, the applicability of the regulations was 
extended to cover St. Joseph and Elkhart Counties. USEPA is taking no 
action on changes to 325 IAC 8-1.1-2(f), Methods of Compliance, and the 
repeal of 325 IAC 8-5-6, Perchloroethylene Dry Cleaning, because these 
exempt the compound perchloroethylene from control without the State 
justifying that such exemption is consistent with the Part D reasonably 
available control technology (RACT) requirements.


    Note: If Indiana allows use of a non-USEPA test method in the 
future, its use must be submitted to USEPA as a SIP revision.


    (i) Incorporation by reference.
    (A) Indiana's Volatile Organic Compounds (VOC) RACT I and II 
regulations, Title 325 Air Pollution Control Board:
    (1) 325 IAC 8-1.1, Establishes Volatile Organic Compound Emission 
Limitations. State promulgated on June 21, 1984, and amended November 7, 
1984.


    Note: 325 IAC 8-1.1-4 Test methods andprocedures. If Indiana allows 
use of a non-USEPA test method in the future, its use must be submitted 
to USEPA as a SIP revision.


    (2) 325 IAC 8-2 Surface Coating Emission Limitations. State 
promulgated on June 21, 1984, and amended November 7, 1984.

[[Page 447]]

    (3) 325 IAC 8-3 Solvent Metal Cleaning Operating Requirements. State 
promulgated on October 15, 1984, and amended November 7, 1984.
    (4) 325 IAC 8-4 Petroleum Sources. State promulgated on June 21, 
1984, and amended November 7, 1984.
    (5) 325 IAC 8-5 Miscellaneous Operations. State promulgated on June 
21, 1984, and amended November 7, 1984.
    (56) On September 2, 1983, the Indiana Air Pollution Control Board 
(Board) submitted revised emission limitations for Occidental Chemical 
Corporation (OCC), located in Clark County, Indiana. Amendments to these 
operating permits were submitted by the State on December 21, 1983. 
These emission limits replace those approved for OCC (under its former 
name, Hooker Chemical) at (c)(34).
    (i) Incorporation by reference.
    (A) Indiana Air Pollution Control Board Operation Permits:
    (1) Control Number 16113, date issued December 27, 1982.
    (2) Control Number 16114, date issued December 27, 1982.
    (3) Control Number 16115, date issued December 27, 1982.
    (ii) Additional material.
    (A) OCC corrected emissions dated September 13, 1984.
    (B) OCC's new modeled data, dated November 6, 1984.
    (C) State's modeling for OCC and surrounding area, dated July 2, 
1984 and August 7, 1984.
    (57) On October 11, 1983, October 24, 1983, and April 16, 1984, 
Indiana submitted a revised Lake County Total Suspended Particulates 
(TSP) Plan, including regulations 325 IAC 6-1-10.2 and 6-1-11.1. This 
plan is disapproved. See Sec. 52.776(j).
    (58) On November 13, 1984, Indiana submitted 325 IAC 13-2, Motor 
Vehicle Tampering and Fuel Switching.
    (i) Incorporation by reference.
    (A) Indiana Rule 325 IAC 13-2, promulgated by the State on September 
24, 1984.
    (59) On March 24, 1986, the State of Indiana submitted a negative 
declaration for synthetic organic chemical manufacturing industry 
(SOCMI) source leaks and oxidation, and for natural gas/gasoline 
processing plants. On April 14, 1986, the State of Indiana submitted a 
negative declaration for manufacturers of high-density polyethylene, 
polypropylene, and polystyrene resins, and for large petroleum dry 
cleaners.
    (i) Incorporation by reference.
    (A) Letter dated March 24, 1986, from Harry D. Williams, Director, 
Air Pollution Control Division, Indiana State Board of Health. Letter 
dated April 14, 1986, from Walter J. Kulakowski, Assistant Commissioner 
for Air Management, Department of Environmental Management.
    (60) On January 18, 1984, Indiana submitted as a revision to the TSP 
SIP certain operating conditions and limits for three coke oven 
batteries at Citizens Gas and Coke Utility in Marion County. The 
operating permits included conditions and limits for Batteries E, H and 
Number One with respect to visible emissions from coke oven doors and 
pushing operations and allowable content of total dissolved solids in 
quench makeup water. EPA disapproves the limit on coke oven door visible 
emissions and total dissolved solids content for quench makeup water on 
Battery Number One, because the limits are inconsistent with that 
battery's Part C Prevention of Significant Deterioration requirements 
and Part D Lowest Achievable Emission Rate requirements. See 
subparagraphs (c)(34) and (c)(42) for further background on actions 
concerning coke oven batteries.
    (i) Incorporation by reference.
    (A) Certificates of Operation Numbers 06895, 06896, and 06897 for 
Citizens Gas and Coke Utility issued by the City of Indianapolis, dated 
June 30, 1980, with addition of operating conditions and emission 
limits, dated September 12, 1983, as adopted by the State on January 4, 
1984, and transmitted on January 18, 1984.
    (ii) Additional information.
    (A) September 7, 1983, letter from the City of Indianapolis to the 
State concerning quarterly analysis of coke quenching makeup water.
    (61) On October 15, 1984, Indiana submitted a revision to the Porter 
County total suspended particulate (TSP) plan, including regulation 325 
IAC 6-6, which

[[Page 448]]

was promulgated by Indiana on November 7, 1984. This plan is 
disapproved. See Sec. 52.776(l).
    (62) On March 4, 1985, Indiana submitted a revision to the Marion 
County carbon monoxide (CO) plan. USEPA approved this plan based on 
monitoring and modeling data and a commitment to implement a one-way 
street pair in the Indianapolis central business district. These 
elements demonstrate attainment of the CO National Ambient Air Quality 
Standards by December 31, 1987.
    (i) Incorporation by reference.
    (A) Marion County CO plan for attainment and maintenance of the CO 
NAAQS from Indianapolis Air Pollution Control Division, Sections 1.0, 
3.4, 4.1, 4.2, 4.3.1, 4.3.2, 4.4, 5.1, 5.5.4, 6.1, 6.2.1, 6.2.2, 6.3, 
and 6.4, dated November 12, 1984.
    (B) Letter from Indiana forwarding Marion County CO plan to USEPA, 
dated March 4, 1985.
    (ii) Additional material.
    (A) Portion of additional technical information from Indianapolis 
Air Pollution Control Division, including Section 1.0, dated August 28, 
1985.
    (B) Letter from Indiana forwarding additional technical information, 
dated October 7, 1985.
    (63) On January 23, 1986, the State submitted revisions to its Stage 
I Gasoline Dispensing regulations, which replace those conditionally 
approved at (c)(33), (c)(35)--Codification only, and (c)(55).
    (i) Incorporation by reference.
    (A) Letter of January 23, 1986 to EPA from the State of Indiana, and 
Title 325 Air Pollution Control Board Rule 325 IAC 8-4-6, Gasoline 
Dispensing Facilities, which was promulgated on January 14, 1986.
    (B) Title 325 Air Pollution Control Board Rule 8-1.1-3, Compliance 
Schedules, subsections (f), (g), and (h), which was promulgated on 
January 14, 1986.
    (64) On January 23, 1986, the State of Indiana submitted to USEPA a 
revision to the Indiana Lead State Implementation Plan in order to 
satisfy the requirements of 40 CFR 51.160 through 51.163 and 51.165(b) 
(formerly 40 CFR 51.18 (a) through (i) and 51.18(k)) for a new source 
review program, USEPA approved this revision for lead new source review 
only.
    (i) Incorporation by reference.
    (A) Construction and Operating Permit Requirements, 325 IAC 2-1.1 
promulgated on January 8, 1986.
    (B) Letter of November 17, 1987, to EPA from the Indiana Department 
of Environmental Management.
    (65) On November 30, 1981, Indiana established its air quality 
surveillance network for lead. On November 21, 1983, Indiana notified 
USEPA that Corning Glass was shut down. On February 18, 1987, Indiana 
submitted its regulation to control lead emissions, 325 IAC 15-1.
    (i) Incorporation by reference.
    (A) 325 IAC 15-1, Lead Emission Limitations, effective February 27, 
1987.
    (B) Letter of February 18, from the State of Indiana to EPA.
    (ii) Additional material.
    (A) A November 30, 1981, letter from Harry Williams, Technical 
Secretary, Indiana Air Pollution Control Board establishing Indiana's 
air quality surveillance network for lead.
    (B) A November 21, 1983, letter from Harry Williams, Technical 
Secretary, confirming that the Corning Glass facility in Wells County 
was permanently shut down and had been taken out of the State's emission 
inventory.
    (C) A June 9, 1987, letter from Timothy Method, Acting Assistant 
Commissioner, submitting a general strategy and additional increments of 
progress required of Hammond Lead.
    (66) On October 21, 1987, the State of Indiana submitted 325 IAC 7-
1-3.1, Reporting Requirements and Methods to Determine Compliance, as a 
revision to its SO2 plan. At paragraph (c)(19) of this 
section, USEPA approved/conditionally approved Indiana's SO2 
plan, 325 IAC 7-1, for most areas of the State. However, the emission 
limits in this plan were set aside by the Court of Appeals for the 
Seventh Circuit because USEPA took no action on the State's 30-day 
averaging compliance method in 325 IAC 7-1-3. New compliance method 325 
IAC 7-1-3.1 replaces former 325 IAC 7-1-3. Therefore, with EPA's 
approval of 325 IAC 7-1-3.1, USEPA is reinstating its March 12, 1982, 
approval of Indiana's October 6, 1980, SO2 rule, 325 IAC 7-1-
1,7-1-2 (except for any emission limits in the below named counties), 7-
1-4, 7-1-5,

[[Page 449]]

7-1-6, and 7-1-7. Other than these general provisions and 325 IAC 7-1-
3.1, USEPA is not acting on or approving today Indiana's SO2 
plan for Dearborn, Floyd, Gibson, Jefferson, Lake, LaPorte, Marion, 
Morgan, Porter, Sullivan, Vermillion, Vigo, Warrick, and Wayne Counties. 
Indiana recodified 325 IAC 7-1-1 through 7-1-7 to 326 IAC 7-1-1 through 
7-1-7 and submitted the recodified rules on November 16, 1988.
    (i) Incorporation by reference.
    (A) 326 IAC 7-1-1 through 326 7-1-7, Sulfur Dioxide Emission 
Limitations, as published in the April 1, 1988, Indiana Register (IR) at 
11 IR 2511.
    (67) On February 3, 1988, Indiana submitted its SO2 plan 
for Jefferson, LaPorte, Marion, Sullivan, and Wayne Counties; on March 
23, 1988, it submitted its SO2 plan for Vermillion County; 
and on August 1, 1988, it submitted its SO submitted the same rules in 
its plans for Jefferson, LaPorte, Marion, Sullivan, and Wayne Counties, 
as recodified into Title 326 of the Indiana Administrative Code. These 
plans consist of the provisions and requirements in 326nIAC 7-1 approved 
or reinstated for these counties at paragraph (c)(66), any 
SO2 emission limits in 326 IAC 7-1-2 applicable in these 
counties (as incorporated by reference at (c)(66)(i)(C)), and the site-
specific SO2 emission limits and other requirements in 326 
IAC 7-1-13 (Jefferson County), 326 IAC 7-1-12 (LaPorte County), 326 IAC 
7-1-9 (Marion County), 326 IAC 7-1-14 (Sullivan County), 326 IAC 7-1-15 
(Vermillion County), 326 IAC 7-1-10.1 (Vigo County), and 326 IAC 7-1-11 
(Wayne County).
    (i) Incorporation by reference.
    (A) 326 IAC 7-1-13, Jefferson County Sulfur Dioxide Emission 
Limitations, as published in the April 1, 1988, Indiana Register (IR) at 
11 IR 2526.
    (B) 326 IAC 7-1-12, LaPorte County Sulfur Dioxide Emission 
Limitations, as published on April 1, 1988, at 11 IR 2526.
    (C) 326 IAC 7-1-9, Marion County Sulfur Dioxide Emission 
Limitations, as published on April 1, 1988, at 11 IR 2518.
    (D) 326 IAC 7-1-14, Sullivan County Sulfur Dioxide Emission 
Limitations, as published on April 1, 1988, at 11 IR 2526.
    (E) 326 IAC 7-1-15, Vermillion County Sulfur Dioxide Emission 
Limitations, as published on March 1, 1988, at 11 IR 1735.
    (F) 326 IAC 7-1-10.1, Vigo County Sulfur Dioxide Emission 
Limitations, as published on August 1, 1988, at 11 IR 3785.
    (G) 325 IAC 7-1-11, Wayne County Sulfur Dioxide Emission 
Limitations, as published on April 1, 1988, at 11 IR 2525.
    (68) On December 2, 1983, Indiana submitted its transportation 
control plans as an element in its ozone strategy for Lake and Porter 
Counties. Further information was submitted on June 10, 1986.
    (i) Incorporation by reference. (A) Chapter 7, Mobile Source 
Strategies and Reductions, Sections A.1.a, 2, and 3 and Exhibits 7-1 and 
7-3 of Indiana's 1982 ozone and carbon monoxide plan, as adopted by the 
Indiana Air Pollution Control Board at its November 2, 1983, metting.
    (B) [Reserved]
    (ii) Additional material. (A) On June 10, 1986, Indiana submitted a 
May 23, 1986, letter from the Northwestern Indiana Regional Planning 
Commission discussing the Lake and Porter Counties' transportation 
control plans and their implementation.
    (B) [Reserved]
    (69) On December 2, 1983, Indiana submitted its ozone plan for Lake 
and Porter Counties, as adopted by the Indiana Air Pollution Control 
Board on November 2, 1983. On March 2, 1984, Indiana submitted as its 
attainment demonstration for Lake and Porter Counties, Illinois' 
attainment demonstration for the greater Chicago area. The greater 
Chicago attainment demonstration, as submitted by Indiana, and Indiana's 
overall ozone plan for Lake and Porter Counties is disapproved. See 
Secs. 52.773(i) and 52.777(d). The disapproval does not affect USEPA's 
approval (or conditional approval) of individual parts of Indiana'a 
ozone plan, and they remain approved. See Sec. 52.770(c) (20), (21), 
(29), (33), (38), (39), (55), (58), and (59).
    (70) On February 3, 1988, and August 23, 1988, Indiana submitted its 
lead plans for Quemetco, Inc., in Indianapolis; Exide Corporation in 
Logansport; C and D Power System in Attica; and General Battery 
Corporation in Frankfort. This included a recodification of

[[Page 450]]

its former lead rule, 325 IAC 15-1 (40 CFR 52.770(c)(65)), to 326 IAC 
15-1 and revisions to this rule.
    (i) Incorporation by reference.
    (A) Title 326--Air Pollution Control Board--Indiana Administrative 
Code (326 IAC) 15-1, Lead Emission Limitations, as published in the 
Indiana Register (IR) on April 1, 1988, at 11 IR 2564.
    (B) Corrections of typographical, clerical, or spelling errors to 
the document printed at 11 IR 2368 (Indiana's recodified air rules, 
including 326 IAC 15-1), as published on August 1, 1988, at 11 IR 3921.
    (71) On March 23, 1988, Indiana submitted its SO2 plan 
for Morgan County; on July 12, 1988, it submitted its SO2 
plan for Floyd County, and on November 16, 1988, it submitted its 
SO2 plan for Warrick County. On December 6, 1988, it 
submitted its Warrick County rule as published in the Indiana Register. 
These plans consist of the provisions and requirements in 326 IAC 7-1 
approved or reinstated for these counties at paragraph (c)(66), and 
SO2 emission limits in 326 IAC 7-1-2 applicable in these 
counties (as incorporated by reference at paragraph (c)(66)(i)(C) of 
this section), and the site-specific SO2 emission limits and 
other requirements in 326 IAC 7-1-16 (Floyd County), 326 IAC 7-1-18 
(Morgan County), and 326 IAC 7-1-17 (Warrick County).
    (i) Incorporation by reference.
    (A) 326 IAC 7-1-16, Floyd County Sulfur Dioxide Emission 
Limitations, as published in the March 1, 1988, Indiana Register (IR) at 
11 IR 1737.
    (B) 326 IAC 7-1-18, Morgan County Sulfur Dioxide Emission 
Limitations, as published on June 1, 1988, at 11 IR 3018.
    (C) 326 IAC 7-1-17, Warrick County Sulfur Dioxide Emission 
Limitations, as published on December 1, 1988, at 12 IR 553.
    (72) On November 16, 1988, Indiana submitted its SO2 plan 
for Dearborn County; on July 12, 1988, it submitted its SO2 
plan for Gibson County; on November 16, 1988, and December 6, 1988, it 
submitted its SO2 plan for Lake County, and on November 16, 
1988, and December 6, 1988, it submitted its SO2 plan for 
Porter County. These plans consist of the provisions and requirements in 
326 IAC 7-1 approved or reinstated for these counties at paragraph 
(c)(66), any SO2 emission limits in 326 IAC 7-1-2 applicable 
in these counties (as incorporated by reference at paragraph 
(c)(66)(i)(C) of this section, and the site-specific SO2 
emission limits and other requirements in 326 IAC 7-1-20 (Dearborn 
County), 326 IAC 7-1-8.1 (Lake County), 326 IAC 7-1-19 (Gibson County), 
and 326 IAC 7-1-21 (Porter County).
    (i) Incorporation by reference.
    (A) 326 IAC 7-1-20, Dearborn County Sulfur Dioxide Emission 
Limitations, as published in the August 1, 1988, Indiana Register (IR) 
at 11 IR 3784.
    (B) 326 IAC 7-1-19, Gibson County Sulfur Dioxide Emission 
Limitations, as published on June 1, 1988, at 11 IR 3019.
    (C) 326 IAC 7-1-8.1, Lake County Sulfur Dioxide Emission 
Limitations, as published on November 1, 1988, at 12 IR 262, and 
corrected on December 1, 1988, at 12 IR 597.
    (D) 326 IAC 7-1-21, Porter County Sulfur Dioxide Emission 
Limitations, as published on November 1, 1988, at 12 IR 259, and 
corrected on December 1, 1988, at 12 IR 597.
    (E) 326 IAC 7-1-1, Applicability, as published on December 1, 1988, 
at 12 IR 552.
    (73) [Reserved]
    (74) On July 23, 1987, the Indiana Department of Environmental 
Management submitted to USEPA a request for a site-specific revision to 
Indiana's ozone SIP. This revision consists of compliance date 
extensions until November 7, 1987, for Uniroyal's two fabric coaters and 
four vinyl printers at its Mishawaka plant, located in St. Joseph 
County, Indiana.
    (i) Incorporation by reference.
    (A) Air pollution Operation Permits Numbers: U 2 33-15A, U 2 34-23, 
U 2 33-14C, U 2 34-3C, U 2 33-16, U 2 33-18, Date issued December 1, 
1988, and Date Expires December 1, 1990.
    (75) [Reserved]
    (76) On October 21, 1987, the State submitted 325 IAC 8-1.1-5, 
Petition for alternative controls, which gives the provisions and 
requirements for petitioning for reasonably available control technology 
volatile organic compound plans. On November 16, 1988, the State 
submitted this rule recodified as 326 IAC 8-1-5, Petition for site-
specific

[[Page 451]]

reasonably available control technology (RACT) plan.
    (i) Incorporation by reference.
    (A) Title 326 Air Pollution Control Board, Indiana Administration 
Code (IAC) 8-1-5, Petition for site-specific reasonably available 
control technology (RACT) plan, as published in the April 1, 1988, 
Indiana Register, at Volume 11 IR 2530. Filed with the Secretary of 
State on March 10, 1988.
    (77) [Reserved]
    (78) On January 18, 1989, and June 23, 1989, Indiana submitted its 
revised lead plan for the HLP-Lead Plant of Hammond Lead Products, Inc. 
in Hammond Indiana. Additionally, minor changes were made to Indiana's 
overall lead rule, 326 IAC 15-1, Lead Emission Limitations.
    (i) Incorporation by reference.
    (A) Title 326--Air Pollution Control Board--Indiana Administrative 
Code (326 IAC) 15-1, as published in the Indiana Register (IR) on July 
1, 1989, at 1850. This rule was effective for State purposes on July 14, 
1989.
    (79) [Reserved]
    (80) On October 15, 1987, the State submitted 325 IAC 8-2-13, Wood 
Furniture and Cabinet Coating, as a portion of its 1982 ozone plan, 
which gives provisions and requirements for controlling volatile organic 
compound (VOC) emissions from sources located in Clark, Floyd, Lake and 
Porter Counties. On November 16, 1988, the State submitted this rule 
recodified as 326 IAC 8-2-12, Wood Furniture and Cabinet Coating.
    (i) Incorporation by reference.
    (A) Title 326 Air Pollution Control Board, Indiana Administrative 
Code (IAC) 8-2-1, Applicability of rule; and 326 IAC 8-2-12, Wood 
furniture and cabinet coating, as published in the April 1, 1988, 
``Indiana Register'' (IR), at 11 IR 2536 and corrected on March 1, 1989, 
at 12 IR 1394. Filed with the Secretary of State on March 10, 1988.
    (81) On April 11, 1988, the State submitted, as a portion of its 
1982 ozone plan, rules to control volatile organic compound (VOC) 
emissions in Lake and Porter Counties. These rules consist of the 
provisions and requirements in 326 IAC 14-1, General Provisions; 326 IAC 
14-8, Emission Standards for Equipment Leaks; and 326 IAC 14-9, Emission 
Limitations for Benzene from Furnace Coke Oven By-product Recovery 
Plants.
    (i) Incorporation by reference.
    (A) Amendments to title 326, Air Pollution Control Board, Indiana 
Administrative Code (IAC) 14-1 General Provisions; 326 IAC 14-8 Emission 
Standards for Equipment Leaks; (Fugitive Emission Sources); and 326 IAC 
14-9 Emission Limitations for Benzene from Furnace Coke Oven By-Product 
Recovery Plants, as published in the June 1, 1988, Indiana Register (IR) 
at 11 IR 3011. Filed with the Secretary of State on April 13, 1988.
    (82) [Reserved]
    (83) On January 21, 1981, the State submitted its revised 
Malfunctions Rule 325 IAC 1.1-5. On November 16, 1988, Indiana submitted 
its recodified regulations. This rule was renumbered 326 IAC 1-6, 
Malfunctions.
    (i) Incorporation by reference. (A) Title 326 of the Indiana 
Administrative Code (IAC), Rule 326 IAC 1-6: Malfunctions as published 
in the April 1, 1988, Indiana Register (IR) at 11 IR 2380. Filed with 
the Secretary of State on March 10, 1988.
    (ii) Additional materials. (A) On July 2, 1982, the State submitted 
clarifications of its intent for 325 IAC 1.1-5.
    (84) On October 27, 1989, and January 19, 1990, Indiana submitted 
its vehicle inspection and maintenance plan for Clark, Floyd, Lake, and 
Porter Counties.
    (i) Incorporation by reference. (A) Title 326, Air Pollution Control 
Board, of the Indiana Administrative Code (IAC), Rule 13-1, Motor 
Vehicle Inspection and Maintenance Requirements, Adopted at 13 Indiana 
Register 500, effective January l, 1990.
    (85) On December 2, 1983, Indiana submitted its transportation 
control plan for Clark and Floyd Counties as one element in its ozone 
plan for the area. Additional material was submitted on May 14, 1986.
    (i) Incorporation by reference. (A) Chapter 7, Mobile Source 
Strategies and Reductions, sections A.1.b and exhibits 7-2 and 7-4, as 
adopted by the Indiana Air Pollution Control Board at its November 2, 
1983, meeting.
    (ii) Additional material. (A) On May 14, 1986, Indiana submitted an 
April 23,

[[Page 452]]

1986, Letter from Jim Thorne, Transportation Director, Kentuckiana 
Regional Planning and Development Agency, discussing the Clark and Floyd 
Counties portion of the Louisville, Kentucky transportation control 
plan.
    (86) On February 15, 1990, Indiana submitted an amended rule which 
updates the applicable edition of the Code of Federal Regulations from 
the 1987 edition to the 1988 edition.
    (i) Incorporation by reference. (A) Title 326, Air Pollution Control 
Board, Indiana Administrative Code (IAC) 1-1-3, References to the Code 
of Federal Regulations, as published in the February 1, 1990, Indiana 
Register (IR), Volume 13 at IR 867. Filed with the Secretary of State on 
December 14, 1989.
    (87) On October 23, 1990, and August 19, 1991, the Indiana 
Department of Environmental Management submitted regulations adopted by 
the Indiana Air Pollution Control Board as part of title 326 of the 
Indiana Administrative Code and intended incorporation to the Indiana 
ozone plan as part of the stationary source control strategy.
    (i) Incorporation by reference.
    (A) The following volatile organic compound rules adopted by the 
Indiana Air Pollution Control Board as part of title 326 of the Indiana 
Administrative Code (326 IAC) and intended to partially satisfy the 
requirements of the Clean Air Act.
    (1) Effective October 23, 1988: 326 IAC 8-1-.05 Coating Definition, 
326 IAC 8-2-11 Fabric and Vinyl Coating.
    (2) Effective February 15, 1990: 326 IAC 1-2-48 Non-Photochemically 
Reactive Hydrocarbon Defined; 326 IAC 8-2-5 Paper Coating Operations.
    (3) Effective May 18, 1990: 326 IAC 1-2-18.5 Cold Cleaner Degreaser 
Defined; 326 IAC 1-2-21.5 Conveyorized Degreaser Defined; 326 IAC 1-2-
29.5 Freeboard Height Defined; 326 IAC 1-2-29.6 Freeboard Ratio Defined; 
326 IAC 1-2-49.5 Open Top Vapor Degreaser Defined; 326 IAC 8-2-9 
Miscellaneous Metal Coating Operations; 326 IAC 8-3-1 Organic Solvent 
Degreasing Operations; 326 IAC 8-5-3 Synthesized Pharmaceutical 
Manufacturing Operations; 326 IAC 8-5-5 Graphic Arts Operations.
    (4) Effective June 8, 1990: 326 IAC 8-1-2 Compliance Methods; 326 
IAC 1-2-90 Volatile Organic Compound (VOC) Definition; 326 IAC 8-1-4 
Testing Procedures.
    (5) Effective June 5, 1991: 326 IAC 1-2-14 Coating Line Definition; 
326 IAC 8-1-1 Applicability of Rule; 326 IAC 8-1-2 Compliance Methods; 
326 IAC 8-1-4 Testing Procedures; 326 IAC 8-2-1 Applicability; 326 IAC 
8-3-5 Cold Cleaner Degreaser Operation and Control; 326 IAC 8-3-6 Open 
Top Vapor Degreaser Operation and Control Requirements; 326 IAC 8-3-7 
Conveyorized Degreaser Operation and Control; 326 IAC 8-4-8 Leaks from 
Petroleum Refineries, Monitoring, Reports; 326 IAC 8-5-5 Graphic Arts 
Operations.
    (88) On February 15, 1990, the Indiana Department of Environmental 
Management submitted a request to revise the Indiana State 
Implementation Plan by adding a site specific particulate matter 
revision for Navistar International Transportation Corporation 
(Navistar) gray iron foundry and engine plant in Indianapolis, Indiana.
    (i) Incorporation by reference.
    (A) Title 326 Air Pollution Control Board, Indiana Administrative 
Code (IAC) 6-1-12 as amended, effective January 13, 1990.
    (89) On July 22, 1991, as supplemented on April 18, 1994, the State 
submitted regulations adopted by the Indiana Air Pollution Control Board 
as part of Title 326 of the Indiana Administrative Code for 
incorporation into the Indiana sulfur dioxide State Implementation Plan.
    (i) Incorporation by reference.
    (A) 326 Indiana Administrative Code 7-4-12.1: Gibson County sulfur 
dioxide emission limitations; effective December 5, 1990. Published in 
the Indiana Register, Volume 14, Number 3, December 1, 1990.
    (90) On March 3, 1989, the Indiana Department of Environmental 
Management submitted a request to revise the Indiana State 
Implementation Plan (SIP) by adding an emission trade or bubble for 
Joseph E. Seagram and Sons which is located in Lawrenceburg, Indiana. 
This requested SIP revision repeals rule 326 Indiana Administrative Code 
(IAC) 6-1-8, adds a new Section, 326 IAC 6-1-8.1, and amends 326 IAC 6-
1-7 to include a reference for the new Section and a recodification of 
the applicable rule.

[[Page 453]]

    (i) Incorporation by reference. (A) Title 326 IAC 6-1-7 as published 
in the Indiana Register Volume 12, Number 6, March 1, 1989, effective 
April 9, 1989.
    (B) Title 326, IAC 6-1-8.1, repeal of 326 IAC 6-1-8 as published in 
the Indiana Register, Volume 12, Number 6, March 1, 1989, effective 
March 1, 1989.
    (91) On January 6, 1994, the State of Indiana submitted a requested 
revision to the Indiana State Implementation Plan (SIP) intended to 
satisfy the requirements of section 182(a)(3)(B) of the Clean Air Act as 
amended in 1990. Included were State rules establishing procedures for 
the annual reporting of emissions of volatile organic material (VOM) and 
oxides of nitrogen (NOx) as well as other regulated air pollutants by 
stationary sources in ozone nonattainment areas.
    (i) Incorporation by reference.
    (A) Title 326 of the Indiana Administrative Code (326 IAC) 2-6 which 
was adopted by the Indiana Air Pollution Control Board, effective 
December 13, 1993.
    (92) On February 25, 1994, Indiana submitted an employee commute 
option rule intended to satisfy the requirements of section 182(d)(1)(B) 
of the Clean Air Act Amendments of 1990.
    (i) Incorporation by reference. (A) Title 326 of the Indiana 
Administrative Code, Article 19 MOBILE SOURCE RULES, Rule 1, Employee 
Commute Options. Filed with the Secretary of State, October 28, 1993, 
effective November 29, 1993. Published at Indiana Register, Volume 17, 
Number 3, December 1, 1993.
    (93) On February 25, 1994, the Indiana Department of Environmental 
Management requested a revision to the Indiana State Implementation Plan 
in the form of Stage II Vapor Recovery Rules as amendments to Title 326 
of the Indiana Administrative Code (326 IAC) 8-1-0.5 and 8-4-6.
    (i) Incorporation by reference.
    (A) 326 IAC 8-1-0.5 Definitions and 8-4-6 Gasoline dispensing 
facilities. Filed with the Secretary of State October 28, 1993, 
effective November 29, 1993. Published at Indiana Register, Volume 17, 
Number 3, December 1, 1993.
    (94) On February 25, 1994, Indiana requested a revision to the State 
Implementation Plan (SIP) in the form of amendments to Title 326: Air 
Pollution Control Board of the Indiana Administrative Code (326 IAC) 2-
1-1 and 2-1-3 which were intended to satisfy the additional new source 
review requirements of the Clean Air Act Amendments of 1990. The USEPA, 
at this time, is also approving the incorporation of permitting rules 
recodified as Article 2. Permit Review Rules of 326 IAC into the SIP to 
replace APC 19 which was incorporated into the Indiana SIP at 40 CFR 
52.770 (c)(24).
    (i) Incorporation by reference.
    (A) Amendments to Title 326 IAC 2-1-1, 2-1-2, 2-1-3, 2-3-1, 2-3-2, 
2-3-3, and 2-3-5. Filed with the Secretary of State November 12, 1993, 
effective December 13, 1993.
    (B) Amendments to Title 326 IAC 2-1-4, 2-1-5, 2-1-6, 2-1-7, 2-1-9, 
2-1-10, 2-1-11, 2-1-12, 2-1-13, 2-3-4. Filed with the Secretary of State 
March 10, 1988, effective April 9, 1988.
    (95) On May 22, 1994, the Indiana Department of Environmental 
Management submitted a request to revise the Indiana State 
Implementation Plan by adding a lead plan for Marion County which 
consists of a source specific revision to Title 326 of the Indiana 
Administrative Code (326 IAC) for Refined Metals.
    (i) Incorporation by reference.
    (A) Amendments to 326 IAC 15-1-2 Source-specific provisions. Filed 
with the Secretary of State March 25, 1994. Effective April 24, 1994. 
Published at Indiana Register, Volume 17, Number 8, May 1, 1994.
    (96) On August 3, 1994 and February 6, 1995, the Indiana Department 
of Environmental Management submitted a requested SIP revision to the 
ozone plan for ozone nonattainment areas.
    (i) Incorporation by reference.
    (A) Indiana Administrative Code, Title 326: Air Pollution Control 
Board, Article 1: General Provisions, Rule 2: Definitions, Section 22.5 
``Department'' definition, Section 28.5 ``Federally enforceable'' 
definition, and Section 64.1 ``Reasonably available control technology'' 
or ``RACT'' definition. Added at 18 Indiana Register 1223-4, effective 
January 21, 1995.
    (B) Indiana Administrative Code, Title 326: Air Pollution Control 
Board, Article 8: Volatile Organic Compound Rules, Rule 7: Specific VOC 
Reduction

[[Page 454]]

Requirements for Lake, Porter, Clark, and Floyd Counties. Added at 18 
Indiana Register 1224-9, effective January 21, 1995.
    (97) On October 25, 1994, the Indiana Department of Environmental 
Management requested a revision to the Indiana State Implementation Plan 
in the form of revisions to State Operating Permit Rules intended to 
satisfy Federal requirements for issuing federally enforceable State 
operating permits (FESOP) and thereby exempt certain small emission 
sources from review under the State's title V operating permit program. 
This FESOP rule is also approved for the purpose of providing federally 
enforceable emissions limits on hazardous air pollutants listed under 
section 112(b) of the Clean Air Act. This revision took the form of an 
amendment to Title 326: Air Pollution Control Board of the Indiana 
Administrative Code (326 IAC) 2-8 Federally Enforceable State Operating 
Permit Program.
    (i) Incorporation by reference. 326 IAC 2-8 Federally Enforceable 
State Operating Permit Program. Sections 1 through 17. Filed with the 
Secretary of State May 25, 1994. Effective June 24, 1994. Published at 
Indiana Register, Volume 17, Number 10, July 1, 1994.
    (98) On October 25, 1994, the Indiana Department of Environmental 
Management requested a revision to the Indiana State Implementation Plan 
in the form of revisions to State Operating Permit Rules intended to 
allow State permitting authorities the option of integrating 
requirements determined during preconstruction permit review with those 
required under title V. The State's Enhanced New Source Review 
provisions are codified at Title 326: Air Pollution Control Board (326 
IAC) 2-1-3.2 Enhanced New Source Review.
    (i) Incorporation by reference. 326 IAC 2-1-3.2 Enhanced new source 
review. Filed with the Secretary of State May 25, 1994. Effective June 
24, 1994. Published at Indiana Register, Volume 17, Number 10, July 1, 
1994.
    (99) On June 16, 1993, December 9, 1993, September 8, 1994, and 
November 17, 1994, Indiana submitted a part D particulate matter (PM) 
nonattainment area plan for the Lake County moderate nonattainment area.
    (i) Incorporation by reference.
    (A) Indiana Administrative Code Title 326: Air Pollution Control 
Board, Article 1: General Provisions, Rule 2: Definitions, Section 32.1: 
``Gooseneck cap'' definition, Section 34.1: ``Jumper pipe'' definition, 
Section 62.1: ``Quench car'' definition, Section 63.1: ``Quench 
reservoir'' definition, and Section 63.2: ``Quench tower'' definition. 
Added at 16 Indiana Register 2363, effective June 11, 1993.
    (B) Indiana Administrative Code Title 326: Air Pollution Control 
Board, Article 5: Opacity Regulations, Rule 1: Opacity Limitations, 
Section 1: Applicability of rule, Section 2: Visible emissions 
limitations, Section 3: Temporary exemptions, Section 4: Compliance 
determination, Section 5: Violations, and Section 7: State 
implementation plan revisions. Amended at 16 Indiana Register 2363, 
effective June 11, 1993.
    (C) Indiana Administrative Code Title 326: Air Pollution Control 
Board, Article 6: Particulate Rules, Rule 1: Nonattainment Area 
Limitations, Opacity Limitations, Section 10.1: Lake County PM10 
emissions requirements (subsections a through k), Section 10.2: Lake 
County PM10 coke battery emissions requirements, and Section 11.1: Lake 
County fugitive particulate matter control requirements. Added at 16 
Indiana Register 2363, effective June 11, 1993.
    (D) Indiana Administrative Code Title 326: Air Pollution Control 
Board, Article 11: Emissions Limitations for Specific Types of 
Operations, Rule 3: Coke Oven Batteries, Section 2: Emissions 
limitations (subsections a through f, and i), and Section 4: Compliance 
determination. Amended at 16 Indiana Register 2363, effective June 11, 
1993.
    (100) On August 25, 1995, Indiana submitted a regulation which bans 
residential open burning in Clark, Floyd, Lake, and Porter Counties in 
Indiana. The regulation allows residential open burning, with certain 
restrictions, in other parts of the State, and describes other types of 
open burning which are allowed in Indiana.
    (i) Incorporation by reference.
    (A) Indiana Administrative Code Title 326: Air Pollution Control 
Board,

[[Page 455]]

Article 4: Burning Regulations, Rule 1: Open Burning, Section 3: 
Exemptions. Added at 18 In. Reg. 2408 Effective June 23, 1995.
    (101) On August 25, 1995, Indiana submitted a regulation which 
reduced the maximum allowable volatility for gasoline sold in Clark and 
Floyd Counties to 7.8 psi during the summer control period. The summer 
control period is June 1, to September 15, for retail outlets and 
wholesale customers, and May 1, to September 15, for all others.
    (i) Incorporation by reference. 326 Indiana Administrative Code 13-3 
Control of Gasoline Reid Vapor Pressure. Sections 1 through 7. Finally 
adopted by the Indiana Air Pollution Control Board January 11, 1995. 
Signed by the Secretary of State July 6, 1995. Effective August 5, 1995. 
Published at Indiana Register, Volume 18, Number 11, August 1, 1995.
    (102) On June 6, 1995, and on September 28, 1995 the Indiana 
Department of Environmental Management submitted State Implementation 
Plan (SIP) revisions establishing an enhanced inspection and maintenance 
(I/M) program in accordance with the requirements of the Clean Air Act 
as amended in 1990. The new enhanced I/M program replaces the basic I/M 
programs in operation in Lake, Porter, Clark, and Floyd Counties. The 
Air Pollution Control Board adopted new rule 326 IAC 13-1.1 and repealed 
existing 326 IAC 13-1, thereby putting in place a revised I/M program.
    (i) Incorporation by reference.
    (A) 326 Indiana Administrative Code 13-1.1 adopted April 5, 1995, 
effective October 1, 1995.
    (ii) Other material.
    (A) June 6, 1995 letter and enclosures from the Indiana Department 
of Environmental Management (IDEM) Commissioner to the Regional 
Administrator of the United States Environmental Protection Agency 
(USEPA) submitting Indiana's revision to the ozone State Implementation 
Plan (SIP).
    (B) September 28, 1995 letter and enclosures from the IDEM Assistant 
Commissioner to the Regional Administrator of USEPA submitting 
supplemental vehicle inspection and maintenance SIP revision information 
and documentation.
    (103) On August 25, 1995, the State submitted regulations adopted by 
the Indiana Air Pollution Control Board as part of title 326 of the 
Indiana Administrative Code for incorporation into the Indiana sulfur 
dioxide State Implementation Plan.
    (i) Incorporation by reference.
    (A) 326 Indiana Administrative Code 7-4-13(3); Dearborn County 
sulfur dioxide emission limitations; effective May 18, 1995. Published 
in the Indiana Register, Volume 18, Number 9, June 1, 1995.
    (104) On December 20, 1995, and February 14, 1996, Indiana submitted 
a Clean-Fuel Fleet Program for Lake and Porter Counties as a revision to 
the State Implementation Plan.
    (i) Incorporation by reference. 326 Indiana Administrative Code 19-3 
Clean Fuel Fleet Vehicles, Sections 1 through 7. Adopted by the Indiana 
Air Pollution Control Board October 4, 1995. Signed by the Secretary of 
State December 19, 1995. Effective January 18, 1996. Published at 
Indiana Register, Volume 19, Number 5, February 1, 1996.
    (105) On October 25, 1994, the Indiana Department of Environmental 
Management submitted a requested revision to the Indiana State 
Implementation Plan in the form of Source Specific Operating Agreement 
(SSOA) regulations. The SSOA regulations are intended to limit the 
potential to emit for a source to below the threshold level of Title V 
of the Clean Air Act. This revision took the form of an amendment to 
title 326: Air Pollution Control Board of the Indiana Administrative 
Code (326 IAC) 2-9-1, 2-9-2(a), 2-9-2(b), and 2-9-2(e) Source Specific 
Operating Agreement Program.

    (i) Incorporation by reference. 326 Indiana Administrative Code 2-9. 
Sections 1, 2(a), 2(b), and 2(e). Adopted by the Indiana Air Pollution 
Control Board March 10, 1994. Signed by the Secretary of State May 25, 
1994. Effective June 24, 1994. Published at Indiana Register, Volume 17, 
Number 10, July 1, 1994.
    (106) On September 19, 1995, and November 8, 1995, Indiana submitted 
automobile and mobile equipment refinishing rules for Clark, Floyd, 
Lake, and Porter Counties as a revision to the State Implementation 
Plan. This rule

[[Page 456]]

requires suppliers and refinishers to meet volatile organic compound 
content limits or equivalent control measures for coatings used in 
automobile and mobile equipment refinishing operations in the four 
counties, as well as establishing certain coating applicator and 
equipment cleaning requirements.
    (i) Incorporation by reference. 326 Indiana Administrative Code 8-
10: Automobile refinishing, Section 1: Applicability, Section 2: 
Definitions, Section 3: Requirements, Section 4: Means to limit volatile 
organic compound emissions, Section 5: Work practice standards, Section 
6: Compliance procedures, Section 7: Test procedures, Section 8: Control 
system operation, maintenance, and monitoring, and Section 9: Record 
keeping and reporting. Adopted by the Indiana Air Pollution Control 
Board June 7, 1995. Filed with the Secretary of State October 3, 1995. 
Published at Indiana Register, Volume 19, Number 2, November 1, 1995. 
Effective November 2, 1995.
    (107) On August 8, 1995, Indiana submitted a site specific SIP 
revision request for Richmond Power and Light in Wayne County Indiana. 
The submitted revisions provide for revised particulate matter and 
opacity limitations on the number 1 and number 2 coal fired boilers at 
Richmond Power and Light's Whitewater Generating Station. The revisions 
also allow for time weighted averaging of stack test results at Richmond 
Power and Light to account for soot blowing. Indiana is making revisions 
to 326 IAC 3-2-1, which currently allows Indiana to authorize 
alternative emission test methods for Richmond Power and Light. Until 
the rule is revised to remove this authority, and approved by the United 
States Environmental Protection Agency, no alternate emission test 
method, changes in test procedures or alternate operating load levels 
during testing is to be granted to Richmond Power and Light.
    (i) Incorporation by reference. Indiana Administrative Code Title 
326: Air Pollution Control Board, Article 3: Monitoring Requirements, 
Rule 2.1: Source Sampling Procedures, Section 5: Specific Testing 
Procedures; Particulate Matter; Sulfur Dioxide; Nitrogen Oxides; 
Volatile Organic Compounds; Article 5: Opacity Regulations, Rule 1: 
Opacity Limitations, Section 2: Visible Emission Limitations; and 
Article 6: Particulate Rules, Rule 1: Nonattainment Area Limitations, 
Section 14: Wayne County. Added at 18 In. Reg. 2725. Effective July 15, 
1995.
    (ii) Additional Information. (A) August 8, 1995 letter from the 
Indiana Department of Environmental Management to USEPA Region 5 
regarding submittal of a state implementation plan revision for Richmond 
Power and Light.
    (108) On August 29, 1995, Indiana submitted a site specific SIP 
revision request for Allison Engine Company in Marion County, Indiana. 
The revision provides limits of 0 tons per year for boilers 2 and 11, 
which have shut down. The hourly mass limits remain unchanged at 0.337 
pounds per million British Thermal Units (lbs/MMBTU) for boilers 1-4 of 
plant 5, 0.15 lbs/MMBTU for boilers 3-6 of plant 8, and 0.15 lbs/MMBTU 
for boilers 7-10 of plant 8. The rule provides for a combined limit of 
130.0 tons per year for the boilers mentioned above, as well as new 
limits on the types and amounts of fuel which may be burned at the 
boilers, and a recordkeeping requirement to document compliance.
    (i) Incorporation by reference. Indiana Administrative Code Title 
326: Air Pollution Control Board, Article 6: Particulate Rules, Rule 1: 
Nonattainment Area Limitations, Section 12: Marion County. Added at 19 
In. Reg. 186. Effective November 3, 1995.
    (109) On October 25, 1994, and April 29, 1997, the Indiana 
Department of Environmental Management requested a revision to the 
Indiana State Implementation Plan in the form of revisions to the 
General Provisions and Permit Review Rules intended to update and add 
regulations which have been effected by recent SIP revisions, and to 
change regulations for streamlining purposes. This revision took the 
form of an amendment to Title 326: Air Pollution Control Board of the 
Indiana Administrative Code (326 IAC) 1-1 Provisions Applicable 
Throughout Title 326, 1-2 Definitions, 1-6 Malfunctions, 2-1 
Construction and Operating Permit Requirements.
    (i) Incorporation by reference. 326 IAC 1-1-2 and 1-1-3. 326 IAC 1-
2-2, 1-2-4, 1-2-

[[Page 457]]

12, 1-2-33.1, and 1-2-33.2. 326 IAC 1-6-1. 326 IAC 2-1-1, 2-1-3, and 2-
1-10. Adopted by the Indiana Air Pollution Control Board March 10, 1994. 
Filed with the Secretary of State May 25, 1994. Effective June 24, 1994. 
Published at Indiana Register, Volume 17, Number 10, July 1, 1994.
    (110) On November 21, 1995, and February 14, 1996, Indiana submitted 
Municipal Solid Waste (MSW) Landfill rules for Clark, Floyd, Lake, and 
Porter Counties as a revision to the State Implementation Plan. This 
rule requires MSW landfills that emit greater than fifty-five tons per 
day of non-methane organic compound, or that have a minimum design 
capacity of one hundred eleven thousand tons (one hundred thousand 
megagrams) of solid waste, to install a landfill gas collection and 
control system that either incinerates the gas or recovers the gas for 
energy use.
    (i) Incorporation by reference. 326 Indiana Administrative Code 8-8 
Municipal Solid Waste Landfills, Section 1 Applicability, Section 2 
Definitions, Section 3 Requirements; incorporation by reference of 
federal standards, Section 4 Compliance deadlines. Adopted by the 
Indiana Air Pollution Control Board July 12, 1995. Filed with the 
Secretary of State December 19, 1995. Published at Indiana Register, 
Volume 19, Number 5, February 1, 1996. Effective January 18, 1996.
    (111) On November 21, 1995, and February 14, 1996, Indiana submitted 
a rule for the control of volatile organic compound emissions from 
volatile organic liquid storage operations in Clark, Floyd, Lake, and 
Porter Counties.
    (i) Incorporation by reference. 326 Indiana Administrative Code 8-9: 
Volatile Organic Liquid Storage Vessels, Section 1: Applicability, 
Section 2: Exemptions, Section 3: Definitions, Section 4: Standards, 
Section 5: Testing and procedures, Section 6: Record keeping and 
reporting requirements. Adopted by the Indiana Air Pollution Control 
Board May 3, 1995. Filed with the Secretary of State December 19, 1995. 
Published at Indiana Register, Volume 19, Number 5, February 1, 1996. 
Effective January 18, 1996.
    (112)  [Reserved]
    (113) On February 13, 1996, and June 27, 1996, Indiana submitted 
rules for the control of volatile organic compound emissions from 
shipbuilding and ship repair operations in Clark, Floyd, Lake, and 
Porter Counties as a revision to the State Implementation Plan.
    (i) Incorporation by reference. 326 Indiana Administrative Code 8-
12: Shipbuilding or Ship Repair operations in Clark, Floyd, Lake, and 
Porter Counties, Section 1: Applicability, Section 2: Exemptions, 
Section 3: Definitions, Section 4: Volatile organic compound emissions 
limiting requirements, Section 5: Compliance requirements, Section 6: 
Test methods and procedures, and Section 7: Record keeping, 
notification, and reporting requirements. Adopted by the Indiana Air 
Pollution Control Board September 6, 1995. Filed with the Secretary of 
State April 1, 1996. Published at Indiana Register, Volume 19, Number 8, 
May 1, 1996. Effective May 1, 1996.
    (114) On November 21, 1995, and February 14, 1996, Indiana submitted 
regulations for wood furniture coating operations in Clark, Floyd, Lake, 
and Porter Counties as a revision to the State Implementation Plan for 
ozone.
    (i) Incorporation by reference. 326 Indiana Administrative Code 8-11 
Wood Furniture Coatings, Section 1 Applicability, Section 2 Definitions, 
Section 3 Emission limits, Section 4 Work practice standards, Section 5 
Continuous compliance plan, Section 6 Compliance procedures and 
monitoring requirements, Section 7 Test procedures, Section 8 
Recordkeeping requirements, Section 9 Reporting requirements, Section 10 
Provisions for sources electing to use emission averaging. Adopted by 
the Indiana Air Pollution Control Board May 3, 1995. Filed with the 
Secretary of State December 5, 1996. Published at Indiana Register, 
Volume 19, Number 5, February 1, 1996. Effective January 4, 1996.
    (115)  [Reserved]
    (116) On September 20, 1996 the Indiana Department of Environmental 
Management submitted a request to revise the Indiana State 
Implementation Plan by adding parachlorobenzotrifluoride (PCBTF), 
cyclic, branched or linear completely methylated siloxanes and acetone 
to

[[Page 458]]

the definition of ``nonphotochemically reactive hydrocarbon,'' and by 
deleting ``vegetable oil'' from a list of compounds not considered to be 
volatile organic compounds (VOC) from the definition of VOC (thus 
including ``vegetable oil'' as a ``VOC'').
    (i) Incorporation by reference.
    (A) 326 IAC 1-2-48 ``nonphotochemically reactive hydrocarbon''. 
Sections 48(a)(22) ``parachlorobenzotrifluoride'' and (23) ``cyclic, 
branched, or linear completely methylated siloxanes.'' 326 IAC 1-2-90 
``volatile organic compound (VOC)'' definition. Section 90. Published in 
Indiana Register, Volume 19, Number 1, October 1, 1995, page 29. Filed 
with the Secretary of State September 5, 1995, effective October 5, 
1995.
    (B) 326 IAC 1-2-48 ``nonphotochemically reactive hydrocarbon.'' 
Section 48(a)(24) ``acetone'' (CAS Number 67-64-1). Published in Indiana 
Register, Volume 19, Number 10, July 1, 1996, page 2856. Filed with the 
Secretary of State, May 13, 1996, effective June 12, 1996.
    (117)  [Reserved]
    (118) On July 12, 1995, Indiana submitted as a revision to the State 
Implementation Plan construction permits CP 019-2110, CP 019-2696, and 
CP 019-4362, issued under Indiana rule 326 IAC 2-1. The permits 
establish volatile organic compound control requirements for Rhodes 
Incorporated's heatset web offset printing presses.
    (i) Incorporation by reference. Construction Permit CP 019-2110, 
issued and effective October 15, 1991; Construction Permit CP 019-2696, 
issued and effective December 18, 1992; Construction permit CP 019-4362, 
issued and effective April 21, 1995.1
    (119) Approval--On October 2, 1996, the State of Indiana submitted a 
State Implementation Plan revision request to eliminate references to 
total suspended particulates (TSP) while maintaining the existing 
opacity requirements. The SIP revision became effective July 19, 1996. 
The SIP revision request satisfies all applicable requirements of the 
Clean Air Act.
    (i) Incorporation by reference. 326 Indiana Administrative Code 5-1: 
Opacity Limitations, Section 1: Applicability of Rule, Section 2: 
Visible emission limitations. Adopted by the Indiana Air Pollution 
Control Board April 3, 1996. Filed with the Secretary of State June 19, 
1996. Published at the Indiana Register, Volume 19, Number 11, August 1, 
1996 (19 IR 3049). Effective July 19, 1996.
    (120) On August 26, 1996, Indiana submitted a rule requiring an 
oxides of nitrogen (NOX) reasonably available control 
technology (RACT) rule for the Clark and Floyd Counties moderate ozone 
nonattainment area as a revision to the State Implementation Plan.
    (i) Incorporation by reference. 326 Indiana Administrative Code 10: 
Nitrogen Oxides Rules. Rule 1: Nitrogen Oxides Control in Clark and 
Floyd Counties. Section 1: Applicability, Section 2: Definitions, 
Section 3: Requirements, Section 4: Emission limits, Section 5: 
Compliance procedures, Section 6: Emissions monitoring, and Section 7: 
Certification, record keeping, and reports. Adopted by the Indiana Air 
Pollution Control Board February 7, 1996. Filed with the Secretary of 
State May 13, 1996. Published at Indiana Register, Volume 19, Number 10, 
July 1, 1996. Effective June 12, 1996.
    (121) On January 23, 1997, the Indiana Department of Environmental 
Management submitted a revision to the State Implementation Plan (SIP) 
for the general conformity rules. The general conformity SIP revision 
enables the State of Indiana to implement and enforce the Federal 
general conformity requirements in the nonattainment and maintenance 
areas at the State and local level in accordance with 40 CFR part 51, 
subpart W--Determining Conformity of General Federal Actions to State or 
Federal Implementation Plans.
    (i) Incorporation by reference. 326 Indiana Administrative Code 16-
3: General Conformity, Section 1: Applicability; incorporation by 
reference of Federal standards. Adopted by the Indiana Air Pollution 
Control Board April 3, 1996. Filed with the Secretary of State June 6, 
1996. Published at the Indiana Register, Volume 19, Number 11, August 1, 
1996 (19 IR 3050). Effective July 6, 1996.
    (122) On July 24, 1997, Indiana submitted rules requiring record 
keeping and reporting requirements for graphic arts sources of volatile 
organic compounds

[[Page 459]]

and amended source applicability requirements for graphic arts sources 
located in Lake and Porter Counties as a revision to the State 
Implementation Plan.
    (i) Incorporation by reference.
    (A) 326 IAC 8-1-9 General record keeping and reporting requirements. 
326 IAC 8-1-10 Compliance certification, record keeping, and reporting 
requirements for certain coating facilities using compliant coatings. 
326 IAC 8-1-11 Compliance certification, record keeping, and reporting 
requirements for certain coating facilities using daily weighted 
averaging. 326 IAC 8-1-12 Compliance certification, record keeping, and 
reporting requirements for certain coating facilities using control 
devices. Adopted by the Indiana Air Pollution Control Board November 6, 
1996. Filed with the Secretary of State April 22, 1997. Published at 
Indiana Register, Volume 20, Number 9, June 1, 1997. Effective May 22, 
1997.
    (B) 326 IAC 8-5-5 Graphic arts operations. Adopted by the Indiana 
Air Pollution Control Board November 6, 1996. Filed with the Secretary 
of State April 22, 1997. Published at Indiana Register, Volume 20, 
Number 9, June 1, 1997. Effective May 22, 1997.
    (123) On July 9, 1997, Indiana submitted a site specific SIP 
revision request for the University of Notre Dame in Saint Joseph 
County, Indiana. The submitted revision amends 326 IAC 6-1-18, and 
provides for revised particulate matter and heat input limitations on 
the five boilers at Notre Dame's power plant.
    (i) Incorporation by reference. Indiana Administrative Code Title 
326: Air Pollution Control Board, Article 6: Particulate Rules, Rule 1: 
Nonattainment Area Limitations, Section 18: St. Joseph County. Added at 
20 In. Reg. 2299. Effective May 22, 1997.
[37 FR 10863, May 31, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.770, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.

    Effective Date Notes:  1. At 63 FR 35144, June 29, 1998, Sec. 52.770 
was amended by adding paragraph (c)(122), effective Aug. 28, 1998.
    2. At 63 FR 35839, July 1, 1998, Sec. 52.770 was amended by adding 
paragraph (c)(123), effective Aug. 31, 1998.



Sec. 52.771  Classification of regions.

    (a) The Indiana plan was evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                               Pollutant
                                                      ----------------------------------------------------------
              Air quality control region                                                           Photochemical
                                                       Particulate   Sulfur   Nitrogen   Carbon      oxidants
                                                          matter     oxides    dioxide  monoxide  (hydrocarbons)
----------------------------------------------------------------------------------------------------------------
East Central Indiana Intrastate......................          II         II       III       III           III
Evansville (Indiana)-Owensboro-Henderson (Kentucky)
 Interstate..........................................           I         II       III       III           III
Louisville Interstate................................           I          I       III       III             I
Metropolitan Chicago Interstate (Indiana-Illinois)...           I          I         I         I             I
Metropolitan Cincinnati Interstate...................           I         II       III       III             I
Metropolitan Indianapolis Intrastate.................           I          I         I         I             I
Northeast Indiana Intrastate.........................          II        III       III       III           III
South Bend-Elkhart (Indiana)-Benton Harbor (Michigan)
 Interstate..........................................           I         IA       III       III           III
Southern Indiana Intrastate..........................          IA         IA       III       III           III
Wabash Valley Intrastate.............................           I          I       III       III           III
----------------------------------------------------------------------------------------------------------------

    (b) The requirements of Sec. 51.150 of this chapter are not met by 
the classification of counties in APC-22 for the purposes of attainment 
and maintenance of the total suspended particulate ambient air quality 
standards.
    (c) The requirements of Sec. 51.150 of this chapter are not met by 
the classification of counties in APC-22 for the purposes of attainment 
and maintenance of the photochemical oxidant (hydrocarbon) ambient air 
quality standards.
    (d) The requirements of Sec. 51.150 of this chapter are not met by 
the classification of Jefferson, LaPorte, Porter, Vigo and Warrick 
Counties in Indiana in Regulation APC-22 for the purposes of attainment 
and maintenance of the

[[Page 460]]

sulfur dioxide ambient air quality standards.
[37 FR 10863, May 31, 1972, as amended at 39 FR 16346, May 8, 1974; 40 
FR 50033, Oct. 28, 1975; 41 FR 35677, Aug. 24, 1976; 42 FR 34519, July 
6, 1977; 51 FR 40675, Nov. 7, 1986]



Sec. 52.772  [Reserved]



Sec. 52.773  Approval status.

    (a) With the exceptions set forth in this subpart, the Administrator 
approves Indiana's plan for attainment and maintenance of the National 
Ambient Air Quality Standards under section 110 of the Clean Air Act.
    (b) [Reserved]
    (c) The Administrator finds that Indiana's new source review 
strategy satisfies all requirements of Part D, Title 1 of the Clean Air 
Act as amended in 1977.
    (d)--(e) [Reserved]
    (f) The Administrator finds ozone strategies for Clark, Elkhart, 
Floyd, Lake, Marion, Porter, and St. Joseph Counties satisfy all 
requirements of Part D, Title I of the Clean Air Act that are required 
to be submitted by January 1, 1981, except as noted below.
    (g) The administrator finds that the total suspended particulate 
strategies for Clark, Dearborn, Dubois, St. Joseph, Vanderburgh, and 
Vigo Counties satisfy all the requirements of Part D, Title I of the 
Clean Air Act except as noted below.
    (h) The Administrator finds that the SO2 strategies for 
Lake, LaPorte, Marion, Vigo, and Wayne Counties satisfy all requirements 
of Part D, Title 1 of the Clean Air Act, as amended in 1977. See 
Sec. 52.770 (c)(67) and (c)(72).
    (i) The Administrator finds that Indiana's ozone plan for Lake and 
Porter Counties, which was required to be submitted by July 1, 1992, 
does not satisfy all the requirements of part D, title 1 of the Clean 
Air Act and, thus, is disapproved. See Secs. 52.770(c)(69)and 52.770(d). 
The disapproval does not affect USEPA's approval (or conditional 
approval) of individual parts of Indiana's ozone plan and they remain 
approved.
    (j) The Administrator finds that the following portions of Indiana's 
ozone and CO plans satisfy the related requirements of part D, title 1 
of the Clean Air Act, as amended in 1977:
    (1) The transportation control plans for Lake, Porter, Clark and 
Floyd Counties, submitted on May 14, 1986, June 10, 1986, and April 6, 
1987.
    (2) The vehicle inspection and maintenance plan for Clark, Floyd, 
Lake, and Porter Counties, submitted October 27, 1989, and January l9, 
1990.
    (3) The demonstration of attainment, submitted December 2, 1983, and 
the carbon monoxide plan as a whole for the designated nonattainment 
area in Lake County.
[37 FR 10864, May 31, 1972, as amended at 46 FR 38, Jan. 2, 1981; 47 FR 
6275, Feb. 11, 1982; 47 FR 6623, Feb. 16, 1982; 47 FR 10825, Mar. 12, 
1982; 47 FR 20586, May 13, 1982; 47 FR 30980, July 16, 1982; 51 FR 4915, 
Feb. 10, 1986; 53 FR 33811, Sept. 1, 1988; 53 FR 46613, Nov. 18, 1988; 
54 FR 2118, Jan. 19, 1989; 55 FR 31052, July 31, 1990; 59 FR 51114, Oct. 
7, 1994]



Sec. 52.774  [Reserved]



Sec. 52.775  Legal authority.

    (a) The requirements of Sec. 51.232(b) of this chapter are not met 
since the following deficiencies exist in the local agency legal 
authority:
    (1) East Chicago: (i) Authority to require recordkeeping is 
inadequate (Sec. 51.230(e) of this chapter).
    (ii) Authority to require installation of monitoring devices is 
inadequate (Sec. 51.230(f) of this chapter).
    (2) Evansville: (i) Authority to prevent construction, modification, 
or operation of any stationary source at any location where emissions 
from such source will prevent the attainment or maintenance of a 
national standard is inadequate (Sec. 51.230(d) of this chapter).
    (ii) Authority to require recordkeeping is inadequate 
(Sec. 51.230(e) of this chapter).
    (iii) Authority to require installation of monitoring devices is 
inadequate (Sec. 51.230(f) of this chapter).
    (3) Gary: (i) Authority to require recordkeeping is inadequate 
(Sec. 51.230(e) of this chapter).
    (ii) Authority to require installation of monitoring devices is 
inadequate (Sec. 51.230(f) of this chapter).
    (4) Hammond: (i) Authority to require recordkeeping is inadequate 
(Sec. 51.230(e) of this chapter).

[[Page 461]]

    (ii) Authority to require installation of monitoring devices is 
inadequate (Sec. 51.230(f) of this chapter).
    (5) Indianapolis: (i) Authority to require recordkeeping is 
inadequate (Sec. 51.230(e) of this chapter).
    (ii) Authority to require installation of monitoring devices is 
inadequate (Sec. 51.230(f) of this chapter).
    (6) Michigan City: (i) Authority to require recordkeeping is 
inadequate (Sec. 51.230(e) of this chapter).
    (ii) Authority to require installation of monitoring devices is 
inadequate (Sec. 51.230(f) of this chapter).
    (7) Wayne County: (i) Authority to require recordkeeping and to make 
inspections and conduct tests of air pollution sources is inadequate 
(Sec. 51.230(e) of this chapter).
    (ii) Authority to require installation of monitoring devices is 
inadequate (Sec. 51.230(f) of this chapter).
    (iii) Authority to prevent construction, modification, or operation 
of any stationary source at any location where emissions from such 
source will prevent the attainment or maintenance of a national standard 
is inadequate (Sec. 51.230(d) of this chapter).
    (8) Lake County: (i) Authority to require installation of monitoring 
devices is inadequate (Sec. 51.230(f) of this chapter).
    (ii) Authority to prevent construction, modification, or operation 
of any stationary source at any location where emissions from such 
source will prevent the attainment or maintenance of a national standard 
is inadequate (Sec. 51.230(d) of this chapter).
    (9) St. Joseph County: (i) Authority to prevent construction, 
modification, or operation of any stationary source at any location 
where emissions from such source will prevent the attainment or 
maintenance of a national standard is inadequate (Sec. 51.230(d) of this 
chapter).
    (ii) Authority to require recordkeeping is inadequate 
(Sec. 51.230(e) of this chapter).
    (iii) Authority to require installation of monitoring devices is 
inadequate (Sec. 51.230(f) of this chapter).
    (10) Vigo County: (i) Authority to require recordkeeping is 
inadequate (Sec. 51.230(e) of this chapter).
    (ii) Authority to require installation of monitoring devices is 
inadequate (Sec. 51.230(f) of this chapter).
    (iii) Authority to prevent construction, modification, or operation 
of any stationary source at any location where emissions from such 
source will prevent the attainment or maintenance of a national standard 
is inadequate (Sec. 51.230(d) of this chapter).
    (11) Anderson County: (i) Authority to require installation of 
monitoring devices is inadequate (Sec. 51.230(f) of this chapter).
[37 FR 10863, May 31, 1972, as amended at 40 FR 55329, Nov. 28, 1975; 51 
FR 40676, Nov. 7, 1986; 52 FR 24367, June 30, 1987]



Sec. 52.776  Control strategy: Particulate matter.

    (a) The requirements of subpart G of this chapter are not met since 
the plan does not provide for attainment and maintenance of the 
secondary standards for particulate matter in the Metropolitan 
Indianapolis Intrastate Region.
    (b) APC 4-R of Indiana's ``Air Pollution Control Regulations'' 
(emission limitation for particulate matter from fuel combustion 
sources), which is part of the control strategy for the secondary 
standards for particulate matter, is disapproved for the Metropolitan 
Indianapolis Intrastate Region since it does not provide the degree of 
control needed to attain and maintain the secondary standards for 
particulate matter. APC 4-R is approved for attainment and maintenance 
of the primary standards for particulate matter in the Metropolitan 
Indianapolis Intrastate Region.
    (c) APC-3 of Indiana's Air Pollution Control Regulations (visible 
emission limitation) is disapproved insofar as the phrase ``for more 
than a cumulative total of 15 minutes in a 24-hour period'' will 
interfere with attainment and maintenance of particulate standards.
    (d) [Reserved]
    (e) Part D--Conditional Approval--The complete Indiana plan for 
Clark, Dearborn, Dubois, Marion (except for coke batteries), St. Joseph, 
Vanderburgh, and Vigo Counties is approved provided that the following 
condition is satisfied:

[[Page 462]]

    (1) The Part D Plan must contain Industrial Fugitive Dust 
Regulations. The State must submit these by July 31, 1982.
    (f) 325 IAC 11-3-2(f), (as amended on August 27, 1981) is not 
approved as it applies to Lake and Marion Counties, insofar as it does 
not meet the requirements of section 172(b)(3) of the Clean Air Act.
    (g) 325 IAC 11-3-2(g) and 11-3-2(h) (as amended on August 27, 1981) 
are disapproved insofar as they do not meet the requirements of section 
110(a)(2)(D) of the Clean Air Act.
    (h) Equivalent Visible Emission Limits (EVEL). (1) A 20% 2-hour 
opacity limit for the underfire stack at Bethlehem Steel Corporation's 
Coke Battery No. 2 in Porter County is approved as an EVEL to determine 
compliance with the 325 IAC 6-2 SIP limit of 0.33 lbs/MMBTU. This EVEL 
is approved for as long as the SIP mass emission limit for this source 
remains the same as determined by 325 IAC 6-2 (October 6, 1980, 
submittal). See Sec. 52.770(c)(6), (35), and (42).
    (2) Revised opacity limits for the boilers at Olin Corporation in 
Warren County are approved at Sec. 52.770(c)(51) as an EVEL to determine 
compliance with the 325 IAC 6-2 SIP limit of 0.80 lbs/MMBTU. This EVEL 
is approved for as long as the SIP mass emission limit for this source 
remains the same as determined by 325 IAC 6-2 (October 6, 1980 
submittal). See Sec. 52.770(c)(6) and (35).
    (i) 325 IAC 6-2.1 is approved with the State's March 27, 1985, 
commitment that any ``bubble'' approved by the State under 325 IAC 6-
2.1-2(b) and 3(b) will also be subject to the State's general ``bubble'' 
regulation, 325 IAC 2-4. The State additionally committed that until 
such time as 325 IAC 2-4 is approved as a part of the SIP, all such 
limits approved under the bubbling provisions of 325 IAC 6-2.1-2(b) and 
3(b) will be submitted as site specific revisions to the SIP. Unless and 
until these emission point specific limits are approved as a portion of 
the SIP, the SIP limit for each individual emission point will remain 
the general limit calculated by means of the formulae in 325 IAC 6-2.1-
2(a) and 3(a), even though a revised emission point specific limit has 
been adopted by Indiana under 325 IAC 6-2.1-2(b) and 3(b). See 
52.770(c)(50).
    (j) The revised Lake County Total Suspended Particulates (TSP) Plan, 
comprised of submittals dated October 11, 1983, October 24, 1983, and 
April 16, 1984, is disapproved because the State did not demonstrate 
that it assures attainment and maintenance of the primary TSP National 
Ambient Air Quality Standards in Lake County, Indiana. See 40 CFR 
51.10(b).
    (k) On January 18, 1984, Indiana submitted a visible emission limit 
on coke oven battery doors and a limit on total dissolved solids content 
of coke quench makeup water for Battery Number One at Citizens Gas and 
Coke Utility in Marion County. These limits are disapproved because they 
are impermissible relaxations of requirements for each new major 
stationary sources, as provided at Sec. 52.21(j)(2) and section 173 of 
the Clean Air Act. See Sec. 52.770(c)(60).
    (l) The revised Porter County TSP plan, as submitted by Indiana on 
October 15, 1984, is disapproved, because the State did not demonstrate 
that it assures the attainment and maintenance of the primary TSP NAAQS 
in Porter County, Indiana. See Sec. 52.770(c)(61).
    (m) The Indiana Part D TSP plan is disapproved insofar as it does 
not contain RACT level opacity limits for certain process fugitive 
sources in TSP nonattainment areas and, therefore, does not meet the 
requirements of section 172 of the Clean Air Act.
    (n) Approval--On June 23, 1988, and July 17, 1989, the State of 
Indiana submitted committal SIPs for particulate matter with an 
aerodynamic diameter equal to or less than 10 micrometers 
(PM10) for the Group II areas within Marion and Vigo Counties 
and all of Porter County, respectively. The committal SIPs meet all the 
requirements identified in the July 1, 1987, promulgation of the SIP 
requirements for PM10 at 52 FR 24681.
    (o) Approval--On November 16, 1988 and September 10, 1992, Indiana 
submitted the following list of control measures for particulate matter 
(PM) already in its State Implementation Plan as a Group III Plan: 326 
IAC 1-3-2, its

[[Page 463]]

air monitoring network, its list of possible additional sites for PM, 
its Prevention of Significant Deterioration rules and the following 
control measures which are part of 325 IAC: 2, Permit Review Rules; 5-1, 
Opacity Limitations; 6-1-1 to 6-1-6, Nonattainment Area Limitations; 6-
1-8, Dearborn County; 6-1-9, Dubois County; 6-1-12, Marion County; 6-1-
13, Vigo County; 6-1-14, Wayne County; 6-1-15, Howard County; 6-1-16, 
Vandenburgh County; 6-1-17, Clark County; 6-1-18, St. Joseph County; 6-
2, Particulate Emissions Limitations for Sources of Indirect Heating; 6-
3, Process Operations; 6-4, Fugitive Dust Emissions; 11-1, Existing 
Foundries; 11-4, Fiberglass Insulation Manufacturing; 11-5, Fluoride 
Emission Limitations for Existing Primary Aluminum Plants.
    (p) Approval-On January 13, 1993, the State of Indiana submitted a 
particulate matter State Implementation Plan revision for the Vermillion 
County nonattainment area. Additional information was submitted on 
February 22, 1993, and April 8, 1993. These materials demonstrate that 
the plan will provide for attainment of the National ambient air quality 
standards for particulate matter by December 31, 1994, in accordance 
with section 189(a)(1)(B) of the Clean Air Act.
    (q) Approval--On April 8, 1993, and supplemented on June 17, 1997, 
the State of Indiana submitted a maintenance plan and a request that 
sections 15, 16, 21, 22, 27, 28, 33 and 34 of Clinton Township in 
Vermillion County be redesignated to attainment of the National Ambient 
Air Quality Standard for particulate matter. The redesignation request 
and maintenance plan satisfy all applicable requirements of the Clean 
Air Act.
[37 FR 15084, July 27, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.776, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.777  Control strategy: Photochemical oxidants (hydrocarbons).

    (a) The requirements of subpart G of this chapter are not met 
because the plan does not provide for attainment and maintenance of the 
national standards for photochemical oxidants (hydrocarbons) in the 
Metropolitan Indianapolis Intrastate Region by May 31, 1975.
    (b) The requirements of subpart G are not met by Revised APC-15 
(November 8, 1974 submission) because it does not provide for attainment 
and maintenance of the photochemical oxidant (hydrocarbon) standards 
throughout Indiana.
    (c) Part D--Conditional approval--The 1979 Indiana plan for Clark, 
Floyd, Elkhart, Lake, Marion, Porter, and St. Joseph Counties is 
approved provided the following conditions are satisfied:
    (1) The plan for stationary source volatile organic compound control 
must contain the following:
    (i)--(iv) [Reserved]
    (v) For regulation 325 IAC 8-5, Section 6, Perchloroethylene Dry 
Cleaning, the State must conduct a study to demonstrate that the 1,500 
gallons exemption meets RACT requirements and submit the results to EPA 
within 6 months of the effective date of final rulemaking on 325 IAC 8 
for VOC from Group II CTG source categories. If the demonstrated 
emissions resulting from the State's exemption are not essentially 
equivalent to those resulting from the RACT requirements, then the State 
must submit to EPA by July 1, 1983, a rule which requires control of 
emissions from dry cleaning sources using less than 1,500 gallons of 
perchloroethylene per year.
    (2) The stationary source volatile organic control measures 
submitted by the State on October 23, 1990, and August 19, 1991, are 
approved as described in 40 CFR 52.770(c)(87) with the exception of 326 
IAC 8-5-4 Pneumatic Rubber Tire Manufacturing, on which USEPA has taken 
no action. It should be noted that although the State's control measures 
provide that equivalent test methods, alternative emission controls, and 
revisions in rule applicability must be submitted to the USEPA as 
proposed revisions to the State Implementation Plan (SIP), such proposed 
SIP revisions are not part of the SIP unless and until they are approved 
as such by the USEPA.
    (d) Part D--Disapproval. The 1982 Indiana plan for Lake and Porter 
County is disapproved because it does not assure the attainment and 
maintenance

[[Page 464]]

of the NAAQS there. See Secs. 52.770(c)(69) and 52.773(i). The 
disapproval does not affect USEPA's approval (or conditional approval) 
of individual parts of Indiana's ozone plan and they remain approved.
    (e) Approval--The Administrator approves the incorporation of the 
photochemical assessment ambient monitoring system submitted by Indiana 
on November 15, 1993, into the Indiana State Implementation Plan. This 
submittal satisfies 40 CFR 58.20(f), which requires the State to provide 
for the establishment and maintenance of photochemical assessment 
monitoring stations (PAMS) by November 12, 1993.
    (f) Approval. The Indiana Department of Environmental Management 
submitted two ozone redesignation requests and maintenance plans 
requesting the ozone nonattainment areas to be redesignated to 
attainment for ozone: South Bend/Elkhart (St. Joseph and Elkhart 
Counties), submitted on September 22, 1993; Indianapolis (Marion 
County), submitted on November 12, 1993. The redesignation requests and 
maintenance plans meet the redesignation requirements in section 
107(d)(3)(d) of the Act as amended in 1990. The redesignations meet the 
Federal requirements of section 182(a)(1) of the Clean Air Act as a 
revision to the Indiana Ozone State Implementation Plan for the above 
mentioned counties.
    (g) The base year ozone precursor emission inventory requirement of 
section 182(a)(1) of the Clean Air Act, as amended in 1990, has been 
satisfied for the following areas: Vanderburgh County in the Evansville 
Metropolitan Area; Marion County in the Indianapolis Metropolitan Area; 
and St. Joseph and Elkhart Counties in the South Bend Metropolitan Area.
    (h) On November 17, 1993, Indiana submitted two of three elements 
required by section 182(d)(1)(A) of the Clean Air Amendments of 1990 to 
be incorporated as part of the vehicle miles traveled (VMT) State 
Implementation Plan intended to offset any growth in emissions from a 
growth in vehicle miles traveled. These elements are the offsetting of 
growth in emissions attributable to growth in VMT which was due November 
15, 1992, and, any transportation control measures (TCMs) required as 
part of Indiana's 15 percent reasonable further progress (RFP) plan 
which was due November 15, 1993. Indiana satisfied the first requirement 
by projecting emissions from mobile sources and demonstrating that no 
increase in emissions would take place. Indiana satisfied the second 
requirement by determining that no TCMs were required as part of 
Indiana's 15 percent RFP plan.
    (i) Approval--EPA is approving the section 182(f) oxides of nitrogen 
(NOX) reasonably available control technology (RACT), new 
source review (NSR), vehicle inspection/maintenance (I/M), and general 
conformity exemptions for the Indiana portion of the Chicago-Gary-Lake 
County severe ozone nonattainment area as requested by the States of 
Illinois, Indiana, Michigan, and Wisconsin in a July 13, 1994 submittal. 
This approval does not cover the exemption of NOX 
transportation conformity requirements of section 176(c) for this area. 
Approval of these exemptions is contingent on the results of the final 
ozone attainment demonstration expected to be submitted in mid-1997. The 
approval will be modified if the final attainment demonstration 
demonstrates that NOX emission controls are needed in the 
nonattainment area to attain the ozone standard in the Lake Michigan 
Ozone Study modeling domain.
    (j) The base year ozone precursor emission inventory requirement of 
section 182(a)(1) of the Clean Air Act, as amended in 1990, has been 
satisfied for Lake and Porter Counties, Indiana.
    (k) On June 26, 1995, and June 13, 1997, Indiana submitted a 15 
percent rate-of-progress plan for the Lake and Porter Counties portion 
of the Chicago-Gary-Lake County ozone nonattainment area. This plan 
satisfies the counties' requirements under section 182(b)(1) of the 
Clean Air Act, as amended in 1990.
    (l)  [Reserved]
    (m) On July 12, 1995, Indiana submitted a 15 percent rate-of-
progress plan for the Clark and Floyd Counties portion of the Louisville 
ozone nonattainment area. This plan satisfies Clark and Floyd Counties' 
requirements under section 182(b) of the Clean Air Act, as amended in 
1990.

[[Page 465]]

    (n) On July 12, 1995, Indiana submitted corrections to the 1990 base 
year emissions inventory for Clark and Floyd Counties. The July 12, 
1995, corrections are recognized revisions to Indiana's emissions 
inventory.
    (o) On July 12, 1995, Indiana submitted as a revision to the Indiana 
State Implementation Plan a ridesharing transportation control measure 
which affects commuters in Clark and Floyd Counties.
    (p) On August 26, 1996, Indiana submitted a rule for the purpose of 
meeting oxides of nitrogen (NOX) reasonably available control 
technology (RACT) requirements under section 182(f) of the Clean Air Act 
(Act) for the Clark and Floyd Counties moderate ozone nonattainment 
area. The rule's NOX control requirements meets RACT for 
major sources of portland cement kilns, electric utility boilers, and 
industrial, commercial, or institutional boilers. In addition, on April 
30, 1997, Indiana certified to the satisfaction of the United States 
Environmental Protection Agency that, to the best of the State's 
knowledge, there are no remaining major sources of NOX in 
Clark and Floyd Counties which need RACT rules. Indiana, therefore, has 
satisfied the NOX RACT requirements under section 182(f) of 
the Act for the Clark and Floyd Counties ozone nonattainment area.
    (q) Approval--On February 5, 1997, Indiana submitted a 
transportation control measure under section 108(f)(1)(A) of the Clean 
Air Amendments of 1990 for Vanderburgh County, Indiana to aid in 
reducing emissions of precursors of ozone. The transportation control 
measure being approved as a revision to the ozone state implementation 
plan is the conversion of at least 40 vehicles from gasoline as a fuel 
to compressed natural gas.
    (r) Indiana's November 15, 1996, request for a 1-year attainment 
date extension for the Indiana portion of the Louisville moderate ozone 
nonattainment area which consists of Clark and Floyd Counties is 
approved. The date for attaining the ozone standard in these counties is 
November 15, 1997.
    (s) Approval--On November 4, 1993, the State of Indiana submitted a 
maintenance plan and a request that Vanderburgh County be redesignated 
to attainment of the 1-hour National Ambient Air Quality Standard for 
ozone. The redesignation request and maintenance plan meet the 
redesignation requirements in section 107(d)(3)(E) of the Clean Air Act 
as amended in 1990. The redesignation meets the Federal requirements of 
section 182(a)(1) of the Clean Air Act as a revision to the Indiana 
ozone State Implementation Plan.
[38 FR 16565, June 22, 1973]

    Editorial Note:  For Federal Register citations affective 
Sec. 52.777, see the List of Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.778  Compliance schedules.

    (a) The requirements of Sec. 51.262(a) of this chapter are not met 
since the compliance schedules for sources of nitrogen oxides extend 
over a period of more than 18 months and periodic increments of progress 
are not included.
    (b)--(c) [Reserved]
    (d) The compliance schedule for the source identified below is 
disapproved as not meeting the requirements of subpart N of this 
chapter. All regulations cited are air pollution control regulations of 
the State, unless otherwise noted.

----------------------------------------------------------------------------------------------------------------
                Source                         Location           Regulation involved     Date schedule adopted
----------------------------------------------------------------------------------------------------------------
                                                   lake county
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½
Commonwealth Edison Co. of Indiana,    Hammond................  APC 13.................  Jan. 18, 1973.
 Inc. (State Line Station).
----------------------------------------------------------------------------------------------------------------

[38 FR 12698 May 14, 1973, as amended at 39 FR 28158, Aug. 5, 1974; 51 
FR 40675, 40676, 40677, Nov. 7, 1986; 54 FR 25258, June 14, 1989]

[[Page 466]]



Sec. 52.779  [Reserved]



Sec. 52.780  Review of new sources and modifications.

    (a) The requirements of Sec. 51.160(a) of this chapter are not met 
in that the plan does not contain procedures to enable the State to 
determine whether construction or modification of coal burning equipment 
having a heat input of between 350,000 Btu per hour and 1,500,000 Btu 
per hour will result in violations of applicable portions of the control 
strategy and section 4(a)(2)(iii) of APC-19 is disapproved to the extent 
that it exempts coal burning equipment having a heat input of between 
350,000 Btu per hour and 1,500,000 Btu per hour from pre-construction/
modification review.
    (b)-(c) [Reserved]
    (d) Limited regulation for the review of new sources and 
modifications. (1) This requirement is applicable to any coal burning 
equipment other than smokehouse generators, having a heat input of 
between 350,000 Btu per hour (88.2 Mg-cal/h) and 1,500,000 Btu per hour 
(378.0 MG cal/h), the construction of which was commenced after May 14, 
1973.
    (2) No owner or operator shall commence construction or modification 
of any coal burning equipment subject to this regulation without first 
obtaining approval from the Administrator of the location and design of 
such source.
    (i) Application for approval to construct or modify shall be made on 
forms furnished by the Administrator,
    (ii) A separate application is required for each source.
    (iii) Each application shall be signed by the applicant.
    (iv) Each application shall be accompanied by site information, 
plans, descriptions, specifications, and drawings showing the design of 
the source, the nature and amount of emissions, and the manner in which 
it will be operated and controlled.
    (v) Any additional information, plans, specifications, evidence, or 
documentation that the Administrator may require shall be furnished upon 
request.
    (3) No approval to construct or modify will be granted unless the 
applicant shows to the satisfaction of the Administrator that:
    (i) The source will operate without causing a violation of any 
local, State, or Federal regulation which is part of the applicable 
plan; and
    (ii) The source will not prevent or interfere with attainment or 
maintenance of any national standard.
    (4) (i) Within twenty (20) days after receipt of an application to 
construct, or any addition to such application, the Administrator shall 
advise the owner or operator of any deficiency in the information 
submitted in support of the application. In the event of such a 
deficiency, the date of receipt of the application for the purpose of 
paragraph (d)(4)(ii) of this section, shall be the date on which all 
required information is received by the Administrator.
    (ii) Within thirty (30) days after receipt of a complete 
application, the Administrator shall:
    (a) Make a preliminary determination whether the source should be 
approved, approved with conditions, or disapproved.
    (b) Make available in at least one location in each region in which 
the proposed source would be constructed, a copy of all materials 
submitted by the owner or operator, a copy of the Administrator's 
preliminary determination and a copy or summary of other materials, if 
any, considered by the Administrator in making his preliminary 
determination; and
    (c) Notify the public, by prominent advertisement in a newspaper of 
general circulation in each region in which the proposed source would be 
constructed, of the opportunity for written public comment on the 
information submitted by the owner or operator and the Administrator's 
preliminary determination on the approvability of the source.
    (iii) A copy of the notice required pursuant to this paragraph shall 
be sent to the applicant and to state and local air pollution control 
agencies, having cognizance over the location where the source will be 
situated.
    (iv) Public comments submitted in writing within thirty (30) days 
after the date such information is made available shall be considered by 
the Administrator in making his final decision on the application. No 
later than

[[Page 467]]

ten (10) days after the close of the public comment period, the 
applicant may submit a written response to any comment submitted by the 
public. The Administrator shall consider the applicant's response in 
making his final decision. All comments shall be made available for 
public inspection in at least one location in the region in which the 
source would be located.
    (v) The Administrator shall take final action on an application 
within thirty (30) days after the close of the public comment period. 
The Administrator shall notify the applicant in writing of his approval, 
conditional approval, or denial of the application, and shall set forth 
his reasons for conditional approval or denial. Such notification shall 
be made available for public inspection in at least one location in the 
region in which the source would be located.
    (vi) The Administrator may extend each of the time periods specified 
in paragraph (d)(4) (ii), (iv) or (v) of this section by no more than 30 
days, or such other period as agreed to by the applicant and the 
Administrator.
    (5) The Administrator may impose any reasonable conditions upon an 
approval, including conditions requiring the source to be provided with:
    (i) Sampling ports of a size, number, and location as the 
Administrator may require,
    (ii) Safe access to each port,
    (iii) Instrumentation to monitor and record emission data, and
    (iv) Any other sampling and testing facilities.
    (6) The Administrator may cancel an approval if the construction is 
not begun within 2 years from the date of issuance, or if during the 
construction, work is suspended for 1 year.
    (7) Any owner or operator subject to the provisions of this 
regulation shall furnish the Administrator written notification as 
follows:
    (i) A notification of the anticipated date of initial startup of a 
source not more than 60 days or less than 30 days prior to such date.
    (ii) A notification of the actual date of initial startup of a 
source within 15 days after such date.
    (8) Within 60 days after achieving the maximum production rate at 
which the source will be operated but not later than 180 days after 
initial startup of such source, the owner or operator of such source 
shall conduct a performance test(s) in accordance with methods and under 
operating conditions approved by the Administrator and furnish the 
Administrator a written report of the results of such performance test.
    (i) Such test shall be at the expense of the owner or operator.
    (ii) The Administrator may monitor such test and may also conduct 
performance tests.
    (iii) The owner or operator of a source shall provide the 
Administrator 15 days prior notice of the performance test to afford the 
Administrator the opportunity to have an observer present.
    (iv) The Administrator may waive the requirement of performance 
tests if the owner or operator of a source has demonstrated by other 
means to the Administrator's satisfaction that the source is being 
operated in compliance with all local, State, and Federal regulations 
which are part of the applicable plan.
    (9) [Reserved]
    (10) Approval to construct or modify shall not relieve any owner or 
operator of the responsibility to comply with all local, State, and 
Federal regulations which are part of the applicable plan.
    (11) Any owner or operator who constructs, modifies, or operates a 
stationary source not in accordance with the application, as approved 
and conditioned by the Administrator, or any owner or operator of a 
stationary source subject to this paragraph who commences construction 
or modification without applying for and receiving approval hereunder, 
shall be subject to enforcement action under section 113 of the Act.
    (e) The requirements of subpart I of this chapter are not met 
because the State failed to submit a plan for review of new or modified 
indirect sources.
    (f) Regulation for review of new or modified indirect sources. The 
provisions of Sec. 52.22(b) are hereby incorporated by reference and 
made a part of the applicable implementation of the plan for the State 
of Indiana.

[[Page 468]]

    (g) Delegation of authority. (1) The Administrator shall have the 
authority to delegate responsibility for implementing the procedures for 
conducting source review pursuant to this section in accordance with 
paragraphs (f) (2), (3), and (4) of this section.
    (2) Where the Administrator delegates the responsibility for 
implementing the procedures for conducting source review pursuant to 
this section to any Agency, other than a Regional Office of the 
Environmental Protection Agency, a copy of the notice pursuant to 
paragraph (d)(4)(iii) of this section shall be sent to the Administrator 
through the appropriate Regional Office.
    (3) In accordance with Executive Order 11752, the Administrator's 
authority for implementing the procedures for conducting source review 
pursuant to this section shall not be delegated, other than to a 
Regional Office of the Environmental Protection Agency, for new or 
modified sources which are owned or operated by the Federal Government 
or for new or modified sources located on Federal lands; except that, 
with respect to the latter category, where new or modified sources are 
constructed or operated on Federal lands pursuant to leasing or other 
Federal agreements, the Federal Land Manager may at his discretion, to 
the extent permissible under applicable statutes and regulations, 
require the lessee or permittee to be subject to new source review 
requirements which have been delegated to a State or local agency 
pursuant to this paragraph.
    (4) The Administrator's authority for implementing the procedures 
for conducting source review pursuant to this section shall not be 
redelegated, other than to a Regional Office of the Environmental 
Protection Agency, for new or modified sources which are located in 
Indian reservations except where the State has assumed jurisdiction over 
such land under other laws, in which case the Administrator may delegate 
his authority to the States in accordance with paragraphs (g) (2), (3), 
and (4) of this section.
    (h) On March 7, 1994, Indiana requested a revision to the State 
Implementation Plan (SIP) for New Source Review (NSR) to satisfy the 
requirements of the Clean Air Act Amendments of 1990. The Indiana 326 
IAC regulations do not include a definition of ``federally 
enforceable''. On July 13, 1994, Pamela Carter, Attorney General of the 
State of Indiana, sent a letter to USEPA clarifying Indiana's 
interpretation of the definition of federally enforceable. The letter 
states that federally enforceable, e.g. as used in 326 IAC 2-3-1, should 
be interpreted in accordance with the federal definition at 40 CFR 
51.165(a)(1)(xiv). The USEPA took the opportunity of rulemaking on the 
State's submittal to recodify the permitting SIP to conform to Title 326 
the Indiana Administrative Code.
[37 FR 10863, May 31, 1972, as amended at 38 FR 12698, May 14, 1973; 39 
FR 4663, Feb. 6, 1974; 39 FR 7281, Feb. 25, 1974; 40 FR 50270, Oct. 29, 
1975; 51 FR 40677, Nov. 7, 1986; 59 FR 51114, Oct. 7, 1994]



Sec. 52.781  Rules and regulations.

    (a) [Reserved]
    (b) A part of the second sentence in section 3, APC-17, which states 
``Where there is a violation or potential violation of ambient air 
quality standards, existing emission sources or any existing air 
pollution control equipment shall comply with th
    (c)-(d) [Reserved]
    (e) Section 2(d) of APC-20, Fugitive Dust Emissions, is disapproved 
because it is unenforceable within the terms of the regulation.
    (f) Subsections 3(b)(3) and 3(b)(5) of APC-2 (May 18, 1977) are 
disapproved because they are unenforceable within the terms of the 
regulation.
[37 FR 10863, May 31, 1972, as amended at 37 FR 15084, July 27, 1972; 38 
FR 12698, May 14, 1973; 40 FR 50033, Oct. 28, 1975; 43 FR 26722, June 
22, 1978]



Sec. 52.782  Request for 18-month extension.

    (a) The requirements of Sec. 51.341 of this chapter are not met 
since the request for an 18-month extension for submitting that portion 
of the plan that implements the secondary standards for particulate 
matter in the Metropolitan Indianapolis Intrastate Region does not show 
that attainment of the secondary standards will require emission 
reductions exceeding those which can be achieved through the application 
of

[[Page 469]]

reasonably available control technology.
[37 FR 10863, May 31, 1972, as amended at 51 FR 40677, Nov. 7, 1986]



Sec. 52.783  [Reserved]



Sec. 52.784  Transportation and land use controls.

    (a) To complete the requirements of subpart L and subpart G of this 
chapter, the Governor of Indiana must submit to the Administrator:
    (1) No later than April 15, 1973, transportation and/or land use 
control strategies and a demonstration that said strategies, along with 
Indiana's presently adopted stationary source emission limitations for 
carbon monoxide and hydrocarbons and the Federal Motor Vehicle Control 
Program, will attain and maintain the national standards for carbon 
monoxide and photochemical oxidants (hydrocarbons) in the Metropolitan 
Indianapolis Intrastate Region by May 31, 1975. By such date (April 15, 
1973), the State also must submit a detailed timetable for implementing 
the legislative authority, regulations, and administrative policies 
required for carrying out the transportation and/or land use control 
strategies by May 31, 1975.
    (2) No later than July 30, 1973, the legislative authority that is 
needed for carrying out such strategies.
    (3) No later than December 30, 1973, the necessary adopted 
regulations and administrative policies needed to implement such 
strategies.
[38 FR 7326, Mar. 20, 1973, as amended at 51 FR 40676, Nov. 7, 1986]



Sec. 52.785  Control strategy: Carbon monoxide.

    (a) The requirements of subpart G of this chapter are not met 
because the plan does not provide for attainment and maintenance of the 
national standards for carbon monoxide in the Metropolitan Indianapolis 
Intrastate Region by May 31, 1975.
[38 FR 16565, June 22, 1973, as amended at 51 FR 40676, Nov. 7, 1986]



Sec. 52.786  Inspection and maintenance program.

    (a) Definitions:
    (1) Inspection and maintenance program means a program to reduce 
emissions from in-use vehicles through identifying vehicles that need 
emission control related maintenance and requiring that such maintenance 
be performed.
    (2) Light-duty vehicle means a motor vehicle rated at 6,000 lb. GVW 
(gross vehicle weight) or less.
    (3) All other terms used in this section that are defined in part 
51, subpart G of this chapter, are used herein with the meanings so 
defined.
    (b) This regulation is applicable in the County of Marion, Indiana 
(including all cities, towns and municipal corporations therein).
    (c) The State of Indiana shall establish and cause the 
implementation of an inspection and maintenance program applicable to 
all gasoline-powered light duty vehicles which are registered in Marion 
County. Such program shall conform with this Sec. 52.786. The 
Consolidated City of Indianapolis, the County of Marion, and other 
municipalities within the County of Marion, shall take all legislative, 
executive, or other action necessary to establish and implement the 
program required by this regulation.
    (d) Not later than April 1, 1975, the State of Indiana, the County 
of Marion and the Consolidated City of Indianapolis shall jointly submit 
to the Administrator, for his approval, legally adopted legislation and/
or regulations establishing the regulatory scheme for the inspection/
maintenance program required by paragraph (c) of this section. The 
legislation and/or regulations shall include:
    (1) Provisions requiring inspection of all light-duty motor vehicles 
subject to the inspection program required by paragraph (c) of this 
section at periodic intervals no more than 1 year apart by means of an 
idle test. Any class or category of vehicles that are found to be rarely 
used on public streets and highways (such as classic or antique 
vehicles) may be exempted.
    (2) Provisions for regulatory criteria that are consistent with 
achieving an 11 percent reduction of hydrocarbon emissions from light-
duty vehicles.
    (3) Provisions ensuring that failed vehicles receive, within 30 
days, the

[[Page 470]]

maintenance necessary to achieve compliance with the inspection 
standards. These provisions shall impose sanctions against owners of 
non-complying vehicles, require retest of failed vehicles following 
maintenance, require a suitable distinctive tag or sticker for display 
on complying vehicles, and include such other measures as are necessary 
or appropriate.
    (4) Provisions establishing a certification program to ensure that 
testing stations performing the required tests have the necessary 
equipment and knowledgeable operators to perform the tests 
satisfactorily, imposing sanctions against non-complying testing 
stations, and containing such other measures as necessary or appropriate 
to a testing program.
    (5) Provisions prohibiting vehicles from being intentionally 
readjusted or modified subsequent to the inspection and/or maintenance 
in such a way as would cause them no longer to comply with the 
inspection standards. These may include authorization of spot checks of 
idle adjustments or of a suitable type of physical seal or tag on 
vehicles. These provisions shall include appropriate penalties for 
violation by any person.
    (6) Designation of agency or agencies responsible for conducting, 
overseeing, and enforcing the inspection/maintenance program. Private 
parties may be designated to conduct parts of the program to certify 
compliance.
    (e) After July 1, 1976, the State of Indiana, County of Marion, the 
Consolidated City of Indianapolis, and other municipalities in Marion 
County shall not allow the operation on streets, roads, or highways 
under their ownership or control of any light duty motor vehicle subject 
to the inspection program established pursuant to paragraph (c) of this 
section that does not comply with the applicable standards and 
procedures adopted in accordance with paragraph (d) of this section.
    (f) After July 1, 1976, no person shall operate or allow the 
operation of any motor vehicle subject to the inspection program 
established pursuant to paragraph (c) of this section that does not 
comply with the applicable standards and procedures adopted in 
accordance with paragraph (d) of this section.
    (g) No later than October 1, 1974, the State of Indiana, County of 
Marion, and the Consolidated City of Indianapolis shall jointly submit 
to the Administrator, for his approval, a detailed compliance schedule 
showing the steps they will take to establish, operate and enforce the 
inspection program required by paragraph (c) of this section including:
    (1) A detailed description of the inspection program required by 
paragraph (c) of this section (including a description of the way in 
which the program will be established, operated, and enforced and the 
respective responsibilities of the State, county, and municipalities for 
such tasks).
    (2) A description of the legal authority for establishing and 
enforcing the inspection/maintenance program, including the text of 
proposed or adopted legislation and regulations.
    (3) Specific dates (day, month, and year) by which various steps to 
implement the inspection/maintenance system will be completed, such 
steps to include, at a minimum, the following: submitting final plans 
and specifications for the system to the Administrator for this approval 
(this date to be no later than February 1, 1975), ordering necessary 
equipment (this date to be no later than April 15, 1975), commencement 
of onsite construction and/or installation, and system operational (this 
date to be no later than April 15, 1975, commencement of onsite 
construction and/ior installation, and system operational (this date to 
be no later than July 1, 1975).
    (4) An identification of the sources and amounts of funds necessary 
to implement the system together with written assurances from the chief 
executive officers of the State, city, and county that they will seek 
such necessary funding from the appropriate legislative bodies.
    (5) Other provisions necessary or appropriate to carry out the 
program.
    (h) The State's December 2, 1992, commitment to timely adopt and 
implement enhanced inspection and maintenance (I/M) rules for Lake and 
Porter Counties is disapproved based on the failure of the State of 
Indiana to meet important milestones pertaining to the development and 
adoption of

[[Page 471]]

necessary authority for the I/M program. This disapproval initiates the 
sanction process of section 179(a) of the Act.
[39 FR 12348, Apr. 5, 1974, as amended at 46 FR 38, Jan. 2, 1981; 51 FR 
40677, Nov. 7, 1986; 55 FR 31052, July 31, 1990; 58 FR 62535, Nov. 29, 
1993]



Sec. 52.787  Gasoline transfer vapor control.

    (a) Gasoline means any petroleum distillate having a Reid vapor 
pressure of 4 pounds or greater.
    (b) This section is applicable in the County of Marion, Indiana 
(including all cities, towns and municipal corporations therein).
    (c) No person shall transfer or permit the transfer of gasoline from 
any delivery vessel into any stationary source container with a capacity 
greater than 250 gallons unless such container is equipped with a 
submerged fill pipe and unless the displaced vapors from the storage 
container are processed by a control system that prevents release to the 
atmosphere of no less than 90 percent by weight of organic compounds in 
said vapors displaced from the stationary storage container location. 
The control system shall include one or more of the following:
    (1) A vapor-tight return line from the storage container to the 
delivery vessel and a system that will ensure that the vapor return line 
is connected before gasoline can be transferred into the container. If a 
``vapor-balance return'' system is used to meet the requirements of this 
section, the system shall be so constructed as to be readily adapted to 
retrofit with an adsorption system, refrigeration-condensation system or 
equivalent system connected to the stationary storage container.
    (2) Refrigeration-condensation sys- tem or adsorption system 
connected to the stationary storage container.
    (3) An equivalent system, approved by the Administrator or his 
designee, designed to recover or eliminate no less than 90 percent by 
weight of the organic compounds in the displaced vapor.
    (d) No person shall own or operate a delivery vessel containing 
gasoline unless the delivery vessel is so designed and maintained as to 
be vapor-tight at all times. This paragraph (d) shall not apply to 
delivery vessels in transit through Marion County which neither are 
filled nor deliver gasoline therein, nor shall this paragraph (d) be 
construed to prohibit safety-valves on other devices required by 
governmental safety regulations. Delivery vessels which are filled in 
Marion County but do not deliver in Marion County may be controlled only 
for filling.
    (e) No person shall own or operate a facility for the filling of 
delivery vessels with gasoline unless the facility is equipped with a 
control system, which can recover or eliminate at least 90 percent by 
weight of the organic compounds in the vapors displaced from the 
delivery vessel during refilling. Facilities which have a daily 
throughput of 20,000 gallons or less are required to have a vapor 
recovery system in operation no later than May 31, 1977. Delivery 
vessels and storage containers served exclusively by facilities required 
to have a vapor recovery system in operation no later than May 31, 1977, 
also will be required to meet the provisions of this section no later 
than May 31, 1977.
    (f) After March 1, 1976, no person shall intentionally release 
gasoline vapors from a delivery vessel, except to a control system that 
can recover or eliminate at least 90 percent by weight of organic 
compounds in the vapors released.
    (g) The provisions of paragraph (c) of this section shall not apply 
to the following:
    (1) Stationary containers having a capacity less than 550 gallons 
used exclusively for the fueling of farming equipment.
    (2) Any stationary container having a capacity less than 2,000 
gallons installed prior to promulgation of this paragraph.
    (3) Transfer made to storage tanks equipped with floating roofs or 
their equivalent.
    (4) Gasoline storage compartments of 1,000 gallons or less in 
gasoline delivery vessels in use on the promulgated date of this 
regulation will not be required to be retrofitted with a vapor return 
system until January 1, 1977.

[[Page 472]]

    (h) The operation of a source, otherwise, subject to paragraph (c), 
(d), or (e) of this section, shall not be a violation of paragraph (c), 
(d), or (e), respectively, if the following acts shall be completed with 
respect to such source before the following dates:
    (1) October 1, 1974. The owner of the source or his designee shall 
submit to the Administrator, a final control plan, which describes at a 
minimum the steps that will be taken by the source to achieve compliance 
with the applicable provisions of paragraphs (c), (d), and (e) of this 
section.
    (2) March 1, 1975. Negotiate and sign all necessary contracts for 
control systems, or issue orders for the purchase of component parts to 
accomplish emission control.
    (3) May 1, 1975. Initiate on-site construction or installation of 
control system equipment.
    (4) February 1, 1976. Complete on-site construction or installation 
of control system equipment.
    (5) March 1, 1976. Achieve final compliance with the applicable 
provisions of paragraphs (c), (d), and (e) of this section.
    (6) Any owner of a source subject to the compliance schedule in this 
paragraph shall certify to the Administrator, within 5 days after the 
deadline for each increment of progress, whether or not the required 
increment of progress has been met.
    (i) As an alternative to compliance with the schedule under 
paragraph (h) of this section:
    (1) The owner of a source which is in compliance with the provisions 
of paragraph (c), (d), or (e) of this section, shall certify such 
compliance to the Administrator by October 1, 1974. The Administrator 
may request whatever supporting information he considers necessary for 
proper certification.
    (2) A source for which a compliance schedule is adopted by the State 
and approved by the Administrator may operate in conformity with such 
compliance schedule.
    (3) The owner of a source may submit to the Administrator, by 
October 1, 1974, a proposed alternative compliance schedule. No such 
schedule may provide for compliance after March 1, 1976. Until 
promulgated by the Administrator, such source shall conform with 
applicable portions of paragraph (c), (d), (e), or (h) of this section. 
Upon promulgation of the compliance schedule by the Administrator, no 
person shall own or operate the source except in conformity with the 
promulgated schedule.
    (j) Nothing in this section shall preclude the Administrator from 
promulgating a separate schedule for any source to which the application 
of the compliance schedule in paragraph (h) of this section fails to 
satisfy the requirements of Sec. 51.15 (b) and (c) of this chapter.
    (k) Any new container, facility, or vessel subject to this 
regulation that is placed in operation after October 1, 1974, shall 
within 30 days of commencing operation submit a compliance schedule in 
conformity with paragraph (i) of this section and shall otherwise comply 
with this section. Any facility subject to this regulation that is 
placed in operation after March 1, 1976, shall comply with the 
applicable requirements of this section immediately upon commencing 
operation.
[39 FR 12349, Apr. 5, 1974, as amended at 39 FR 41253, Nov. 26, 1974; 41 
FR 56643, Dec. 29, 1976; 42 FR 29004, June 7, 1977]



Sec. 52.788  Operating permits.

    Emission limitations and other provisions contained in operating 
permits issued by the State in accordance with the provisions of the 
federally approved permit program shall be the applicable requirements 
of the federally approved State Implementation Plan (SIP) for Indiana 
for the purpose of sections 112(b) and 113 of the Clean Air Act and 
shall be enforceable by the United States Environmental Protection 
Agency (USEPA) and any person in the same manner as other requirements 
of the SIP. USEPA reserves the right to deem an operating permit not 
federally enforceable. Such a determination will be made according to 
appropriate procedures, and be based upon the permit, permit approval 
procedures or permit requirements which do not conform with the 
operating permit program requirements or the requirements of USEPA's 
underlying regulations.
[60 FR 43012, Aug. 18, 1995]

[[Page 473]]



Secs. 52.789--52.792  [Reserved]



Sec. 52.793  Significant deterioration of air quality.

    (a) The requirements of sections 160 through 165 of the Clean Air 
Act are not met, since the plan does not include approvable procedures 
for preventing the significant deterioration of air quality.
    (b) Regulations for preventing significant deterioration of air 
quality. The provisions of Sec. 52.21(b) through (w) are hereby 
incorporated and made a part of the applicable state plan for the State 
of Indiana.
    (c) All applications and other information required pursuant to 
Sec. 52.21 from sources located in the State of Indiana shall be 
submitted to the Commissioner, Indiana Department of Environmental 
Management, 105 South Meridian Street, P.O. Box 6015, Indianapolis, IN 
46206.
[45 FR 52741, Aug. 7, 1980, as amended at 53 FR 18985, May 26, 1988]



Sec. 52.794  Source surveillance.

    (a) The requirements of 51.212 of this chapter are not met by the 
phrase ``for more than a cumulative total of 15 minutes in a 24-hour 
period'' contained in section 1 of APC-3 of the Indiana Air Pollution 
Control Regulations.
    (b) [Reserved]
    (c) 325 IAC 5-1 (October 6, 1980, submittal--Sec. 52.770(c)(53)) is 
disapproved for the Lake County sources specifically listed in Table 2 
of 325 IAC 6-1-10.2 (Sec. 52.770(c)(57)); for pushing and quenching 
sources throughout the State (August 27, 1981, 325 IAC 11-3-2 (g) and 
(h)--Sec. 52.770(c)(42)); and for coke oven doors in Lake and Marion 
Counties (325 IAC 11-3-2(f)--Sec. 52.770(c)(42)). Applicability of this 
regulation to these sources is being disapproved because 325 IAC 5-1 
does not meet the enforceability requirements of Sec. 51.22 as it 
applies to these sources. Opacity limits in 325 IAC 6-1-10.2 and certain 
opacity limits in 325 IAC 11-3 supersede those in 325 IAC 5-1, and USEPA 
has previously disapproved these superseding regulations (Sec. 52.776 
(j), (g), and (f), respectively).
[40 FR 50033, Oct. 28, 1975; 41 FR 3475, Jan. 23, 1976, as amended at 48 
FR 55860, Dec. 16, 1983; 51 FR 40676, 40677, Nov. 7, 1986; 52 FR 3644, 
Feb. 5, 1987; 52 FR 23038, June 17, 1987]



Sec. 52.795  Control strategy: Sulfur dioxide.

    (a) Revised APC-13 (December 5, 1974 submission) of Indiana's Air 
Pollution Control regulations (sulfur dioxide emission limitation) is 
disapproved insofar as the provisions identified below will interfere 
with the attainment and maintenance of the suffix dioxide ambient air 
quality standards:
    (1) The phrase ``equivalent full load'' in section 1(b)(2).
    (2) The formula ``Ep=17.0 Qm 0.67 
where Ep=Em x Qm'' in section 2(a).
    (3) The phrase ``Direct fired process operations'' in sections 2(a), 
3(c), 4(b), and 4(c).
    (4) The modification of Qm for non-Indiana coal as 
expressed in Section 2(a).
    (b) The requirements of Sec. 51.281 are not met by Warrick and 
Culley electrical generating stations enforcement orders which would 
revise the sulfur dioxide emission limitations for these two stations.
    (c) The requirements of Sec. 51.110(e) are not met by Wayne, 
Dearborn, Jefferson, Porter, and Warrick Counties.
    (d)--(e) [Reserved]
    (f) Approval--On March 14, 1996, the State of Indiana submitted a 
maintenance plan for Lawrence, Washington, and Warren Townships in 
Marion County and the remainder of the county, and requested that it be 
redesignated to attainment of the National Ambient Air Quality Standard 
for sulfur dioxide. The redesignation request and maintenance plan 
satisfy all applicable requirements of the Clean Air Act.
    (g) Approval--On June 17, 1996, the State of Indiana submitted a 
maintenance plan for LaPorte, Vigo, and Wayne Counties and requested 
redesignation to attainment for the National Ambient Air Quality 
Standard for sulphur dioxide for each county in its entirety. The 
redesignation requests and

[[Page 474]]

maintenance plans satisfy all applicable requirements of the Clean Air 
Act.
[41 FR 35677, Aug. 24, 1976, as amended at 42 FR 34519, July 6, 1977; 47 
FR 10825, Mar. 12, 1982; 47 FR 39168, Sept, 7 1982; 49 FR 585, Jan. 5, 
1984; 51 FR 40676, 40677, Nov. 7, 1986; 53 FR 1358, Jan. 19, 1988; 54 FR 
2118, Jan. 19, 1989; 61 FR 58486, Nov. 15, 1996]



Sec. 52.796  Industrial continuous emission monitoring.

    (a) APC-8, Appendix I 1.2.3, 3.3, and 6.0 are disapproved because 
they do not meet the requirements of 40 CFR 51.214.
    (b)(1) The requirements of 40 CFR 51, Appendix P 3.3 are hereby 
incorporated and made a part of the applicable implementation plan for 
the State of Indiana.
    (2) APC-8 does not apply to any source scheduled for retirement by 
October 6, 1980, or within five years after the promulgation of 
continuous emission monitoring requirements for that source category in 
40 CFR part 51, Appendix P 1.1, provided that adequate evidence and 
guarantees are provided that clearly show that the source will cease 
operations on or before such date.
[43 FR 26722, June 22, 1978, as amended at 51 FR 40677, Nov. 7, 1986]



Sec. 52.797  Control strategy: Lead.

    Indiana's control strategy for lead is approved except as noted 
below:
    (a)--(b) [Reserved]
    (c) On January 12, 1988, Indiana'a Office of Air Management (OAM), 
Indiana Department of Environmental Management, agreed to review all 
relevant hood designs and performance guidance to determine which 
criteria to use in determining ongoing compliance with the capture 
efficiency provisions in 326 IAC 15-1 for Quemetco, Inc., and Refined 
Metals. Because these efficiencies are closely related to equipment 
design, OAM believes that a review of the process and control equipment 
designs and operating paramenters should provide the necessary 
determination of compliance. OAM will work with the Indianapolis local 
agency, the Indianapolis Air Pollution Control Division, on viable 
alternatives and will keep USEPA up to date on its progress. OAM 
anticipates that specific criteria for determining compliance will be 
incorporated into the sources' operation permits (and forwarded to USEPA 
for informational purposes), and, should the opportunity arise, 326 IAC 
15-1 will be revised to similarly incorporate capture efficiency 
criteria.
[53 FR 12905, Apr. 19, 1988, as amended at 53 FR 38722, Oct. 3, 1988; 54 
FR 33896, Aug. 17, 1989]



Sec. 52.798  Small business stationary source technical and environmental compliance assistance program.

    The Indiana program submitted on January 14, 1993, as a requested 
revision to the Indiana State Implementation Plan satisfies the 
requirements of section 507 of the Clean Air Act Amendments of 1990.
[58 FR 46544, Sept. 2, 1993]



                             Subpart Q--Iowa



Sec. 52.820  Identification of plan.

    (a) Title of plan: ``State of Iowa Air Pollution Control 
Implementation Plan.''
    (b) The plan was officially submitted on January 27, 1972.
    (c) The plan revisions listed below were submitted on the dates 
specified:
    (1) Request for a two-year extension to meet the National Primary 
and Secondary Ambient Air Quality Standards for nitrogen dioxide in the 
Metropolitan Omaha-Council Bluffs Interstate Air Quality Control Region 
was submitted by the Governor on January 27, 1972. (Non-regulatory)
    (2) Revisions of Appendices D and G of the plan were submitted on 
February 2, 1972, by the State Department of Health. (Non-regulatory)
    (3) Source surveillance and record maintenance statements were 
submitted on April 14, 1972, by the State Department of Health. (Non-
regulatory)
    (4) Revised statement regarding public availability of emission data 
was submitted on May 2, 1972, by the State Department of Health. (Non-
regulatory)
    (5) State submitted Senate File 85 which created the Department of 
Environmental Quality and replaced the Iowa air pollution control 
statute which appeared as Chapter 136B of the

[[Page 475]]

Code of Iowa, on May 4, 1972. (Regulatory)
    (6) A letter describing the issuance of a Certificate of Acceptance 
for the local air pollution control programs conducted by the Linn 
County Board of Health for the jurisdictions of the City of Cedar Rapids 
and Linn County, and the Des Moines-Polk County Health Department for 
the jurisdictions of the City of Des Moines and Polk County was 
submitted by the State Department of Health on December 14, 1972. (Non-
regulatory)
    (7) Compliance schedules were submitted by the State in February 
1973. (Regulatory)
    (8) Compliance schedules were submitted by the State in May 1973. 
(Regulatory)
    (9) The State of Iowa High Air Pollution Episode Contingency Plan 
was submitted on June 20, 1973, by the Governor.
    (10) The letter which requested the inclusion of the Linn County 
Health Department Rules and Regulations, the City of Cedar Rapids Air 
Pollution Control Ordinance, the Polk County Rules and Regulations--Air 
Pollution Control, and the City of Des Moines Air Pollution Control 
Regulations in the State of Iowa implementation plan was submitted by 
the State Department of Environmental Quality on June 25, 1974. (No 
approval action was taken on the request because it did not meet the 
procedural requirements specified in 40 CFR part 51.)
    (11) Revisions of Rules 2.1, 3.1, 3.4, 4.1, 4.3(3) and 4.3(4) of the 
Iowa Rules and Regulations Relating to Air Pollution Control were 
submitted on April 24, 1974 (by the Governor's office). (No approval or 
disapproval action was taken on amended Subrule 4.3(3)a., which 
restricts emissions of sulfur oxides from fuel-burning sources.) 
(Regulatory)
    (12) Compliance schedules were submitted by the State in May 1974.
    (13) Compliance schedules were submitted by the State in May 1974.
    (14) Compliance schedules were submitted by the State in July 1974.
    (15) Compliance schedules were submitted by the State in August 
1974.
    (16) A letter from the Director of the Department of Environmental 
Quality, dated August 29, 1974, which requested that no further action 
be taken on Subrule 4.3(3) a. as submitted on April 24, 1974. 
(Regulatory)
    (17) Compliance schedules were submitted by the State in September 
1974.
    (18) Compliance schedules were submitted by the State in November 
1974.
    (19) Compliance schedules were submitted by the State in February 
1975.
    (20) Compliance schedules were submitted by the State in April 1975.
    (21) Compliance schedules were submitted by the State in June 1975.
    (22) Revisions of Rules 1.2, 2.1, 3.1, 3.4, 4.1, 4.2, 4.3, 5.1, 7.1, 
8.3 and 8.4 of the Iowa Rules and Regulations Relating to Air Pollution 
Control were submitted on July 17, 1975, by the Governor's office. 
(Regulatory) (No approval or disapproval action was taken on Subrules 
4.3(2)c. or 4.3(3)b.)
    (23) Summary of the public hearing which was held on the revised 
rules which were submitted on July 17, 1975, by the Governor's office 
was submitted by the Iowa Department of Environmental Quality on 
September 3, 1975. (non-regulatory)
    (24) Letter which withdrew amended Subrule 4.3(2)c. from the 
proposed Iowa plan revision submitted on July 17, 1975, was submitted by 
the Governor's office on January 20, 1976.
    (25) Revisions to Rules 1.2, 2.1, 3.1, 3.2, 4.1, 4.3, 4.4, and new 
Chapters 14 and 52 of the Iowa Administrative Code Relating to Air 
Pollution Control were submitted June 9, 1976, by the Department of 
Environmental Quality (Subrules 4.3(3)a(1) and 4. 3(3)a(5) were 
disapproved).
    (26) Additional air quality modeling to support the sulfur dioxide 
emission standards of Subrules 4.3(3)a(1) and 4.3(3)a(2) was submitted 
March 4, 1977, by the Department of Environmental Quality (Non-
regulatory).
    (26a) Revisions of Rules 1.2, 4.3(2)b, 4.4(6), 4.4(12) and of 
Chapter 7 of the Iowa Administrative Code relating to Air Pollution 
Control were submitted June 20, 1977, by the Department of Environmental 
Quality.
    (27) Nonattainment plan provisions as required by the Clean Air Act 
Amendments of 1977 were submitted on June 22, 1979, by the Department of 
Environmental Quality. The submission included amended rule 4.3(2) 
relating to

[[Page 476]]

fugitive dust and new rule 4.5 relating to offsets for particulate 
matter. The revisions included attainment plans for particulate in Mason 
City and Davenport, particulate and ozone in Cedar Rapids and 
particulate and carbon monoxide in Des Moines. The submission was 
disapproved in part for failure to meet the requirements of Section 173 
and was conditionally approved with respect to several requirements.
    (28) On October 8, 1979, the Iowa Department of Environmental 
Quality submitted additional information to support the June 22, 1979, 
submission.
    (29) On November 16, 1979, the Iowa Air Quality Commission submitted 
additional information and commitments to allow approval or conditional 
approval of portions of the June 22, 1979, submission.
    (30) Nonattainment plan provisions as required by the Clean Air Act 
Amendments of 1977 were submitted on April 18, 1980, by the Department 
of Environmental Quality. The submission included amended rule 4.3(2) 
relating to fugitive dust and amended rule 3.5 relating to particulate 
matter offsets. The revisions included plans to attain the secondary 
particulate standards for all areas designated nonattainment as of March 
6, 1980. The submission was conditionally approved with respect to 
several requirements.
    (31) The State of Iowa Lead State Implementation Plan was submitted 
on August 19, 1980 by the Director of the Department of Environmental 
Quality.
    (32) Additional information to support the April 18, 1980 submission 
was submitted on September 16, 1980, by the Department of Environmental 
Quality.
    (33) Additional information to support the April 18, 1980 submission 
was submitted on November 17, 1980, by the Department of Environmental 
Quality.
    (34) A revised Chapter 5, dealing with excess emissions and 
malfunctions was submitted on December 23, 1980, by the Department of 
Environmental Quality.
    (35)  [Reserved]
    (36) A letter was submitted dated January 19, 1981 by the Director 
of the Department of Environmental Quality which provided additional 
information concerning the Iowa Lead State Implementation Plan.
    (37) A variance from 400--4.2(1) of the Iowa Administrative Code for 
the Iowa Army Ammunition Plant at Middletown, Iowa, was submitted on 
October 19, 1979 by the Executive Director.
    (38) Revisions to Subrule 400--4.3(2)``c'' relating to fugitive 
emissions control and a document describing how this subrule is to be 
enforced were submitted on June 1, 1981, by the Department of 
Environmental Quality.
    (39) A schedule for studying nontraditional sources of particulate 
matter and for implementing the results of the studies in the form of 
control strategies was submitted on June 26, 1981 by the Department of 
Environmental Quality. (Non-Regulatory).
    (40) Revisions to Subrule 400--4.3(2)``b'' relating to particulate 
emissions from fuel burning sources were submitted on July 31, 1981, by 
the Department of Environmental Quality.
    (41) The Iowa Ambient Air Monitoring Strategy was submitted July 15, 
1981, by the Department of Environmental Quality (non-regulatory).
    (42) A conditional permit containing an alternative emission 
reduction program for the Progressive Foundry, Inc., of Perry, Iowa, 
under 400-3.7 and 400-4.6 of the Iowa Administrative Code; and an 
administrative order setting forth a compliance schedule, were submitted 
on December 18, 1981, by the Executive Director. The conditional permit 
specifies particulate emissions not to exceed 16.3 pounds per hour from 
the gray iron cupola with a process weight rate not to exceed 8534 
pounds per hour and specifies the casting shakeout exhaust system shall 
not exceed 0.05 grains per standard cubic foot nor 12.8 pounds per hour 
of particulate matter. The compliance schedule specifies a final 
compliance date of September 1, 1983.
    (43) On July 1, 1983, the State's air pollution control regulations 
were recodified at Department 900, Title II, Chapters 20 through 29.
    (44) Revised Chapter 22 regulations, dealing with new source review 
in nonattainment areas, were submitted on July 18, 1984, by the Iowa 
Department of Water, Air and Waste Management. Subrules 22.5(4) g, i, 
and j remain unapproved. EPA will temporarily defer action on these 
subrules pending a May

[[Page 477]]

14, 1985, commitment from the State to submit appropriate revisions.
    (i) Incorporation by reference. Revised Chapter 22 regulations, 
dealing with new source review in nonattainment areas, adopted by the 
State on July 17, 1984.
    (ii) Additional material. May 14, 1985, letter of commitment from 
the State to revise unapprovable portions of their Chapter 22 air 
pollution regulations.
    (45) Revised Chapter 22 subrules 22.5(2) a and b; and revised 
subrules 22.5(4) g, i, and j, all relating to new source review in 
nonattainment areas, were submitted on December 31, 1985, by the Iowa 
Department of Water, Air and Waste Management.
    (a) Incorporation by reference.
    (i) Revised Chapter 22 subrules 22.5(2) a and b; and subrules 
22.5(4) g, i, and j, adopted by the State on December 17, 1985.
    (ii) April 22, 1986, letter of commitment from the Iowa Department 
of Water, Air and Waste Management to submit stack height regulations by 
May 30, 1986, and to implement EPA's stack height requirements until 
such time that the regulations are fully approved.
    (46) Revised Chapter 22 regulations pertaining to new source review 
in attainment and unclassified areas of the state (PSD) were submitted 
on March 9, 1987, by the Iowa Department of Natural Resources.
    (i) Incorporation by reference.
    (A) Iowa Administrative Bulletin (ARC 7446), amendments to Chapter 
22, ``Controlling Pollution,'' adopted by the Iowa Environmental 
Protection Commission on February 17, 1987.
    (B) Letter from Iowa dated April 22, 1987, committing to 
implementation of its stack height regulations in a manner consistent 
with EPA's stack height regulations with respect to new source review/
PSD regulations.
    (47) Revised Chapters 22 and 23 regulations pertaining to stack 
height credits for modeling purposes were submitted on May 20, 1986, by 
the Iowa Department of Natural Resources. Revised definition of 
``emission limitation'' and ``emission standard'' at Iowa regulation 
567.20.2(455B), Definitions.
    (i) Incorporation by reference.
    (A) Iowa Administrative Bulletin (ARC 6566), amendments to Chapter 
22, ``Controlling Pollution'' and Chapter 23, ``Emission Standards for 
Contaminants'' adopted by the Iowa Environmental Protection Commission 
on April 22, 1986, effective June 25, 1986.
    (B) Iowa Administrative Bulletin (ARC 8023) amendment to 567-
20.2(455B). Effective September 22, 1987.
    (48) Revised Chapter 22, subrule 22.1(2)``d'' exemptions from permit 
requirements were submitted on September 13, 1988, by the Iowa 
Department of Natural Resources. The revision clarifies permit 
exemptions for certain grain roasting equipment.
    (i) Incorporation by reference.
    (A) Amendment to Chapter 22, ``Controlling Pollution,'' Iowa 
Administrative Code, subrule 22.1(2)``d'', effective September 14, 1988.
    (49) Revised Polk County, Iowa, Board of Health Rules and 
Regulations, Chapter V, Air Pollution, submitted by the Iowa Department 
of Natural Resources on February 3, 1988. EPA approves these regulations 
with the provision that any operating permit which changes any 
requirement of the Iowa SIP, including requirements in any construction 
permit, must be submitted to EPA, and approved, as a SIP revision. In 
the absence of such approval, the enforceable requirements shall be 
those in the Iowa SIP.
    (i) Incorporation by reference.
    (A) Ordinance No. 28, Amendment to Polk County Board of Health Rules 
and Regulations chapter V, Air Pollution, Article I, 5-1 and 5-2 (except 
for variance); Article II, 5-3; and Article X, 5-28 through 5.50-1 
(except for 5-49 and 5-50), effective October 8, 1987.
    (ii) Additional material.
    (A) None.
    (50) Revised Linn County, Iowa, Chapter 10 Ordinance ``Air Pollution 
Control'' submitted as a SIP revision by the Iowa Department of Natural 
Resources on February 3, 1988. EPA approves these regulations with the 
provision that any operating permit which changes any requirement of the 
Iowa SIP, including requirements in any construction permit, must be 
submitted to EPA, and approved, as a SIP revision. In the absence of 
such approval,

[[Page 478]]

the enforceable requirements shall be those in the Iowa SIP.
    (i) Incorporation by reference.
    (A) Linn County Chapter 10 Ordinance ``Air Pollution Control'' 
sections 10.1 (except for 10.1(50)), 10.2, 10.3, and 10.4, adopted by 
the Linn County Board of Supervisors on September 2, 1987.
    (ii) Additional material.
    (A) None.
    (51) Revised Iowa regulations pertaining to PM10 were 
submitted by the state on October 28, 1988. These rules became effective 
on December 21, 1988.
    (i) Incorporation by reference.
    (A) Amended Iowa Administrative Code pertaining to the prevention, 
abatement, and control of air pollution: Chapter 20, ``Scope of Title--
Definitions--Forms--Rules of Practice;'' Chapter 22, ``Controlling 
Pollution;'' Chapter 26, ``Prevention of Air Pollution Emergency 
Episodes;'' and Chapter 28, ``Ambient Air Quality Standards,'' effective 
December 21, 1988.
    (ii) Additional information.
    (A) None.
    (52) Revised chapter 22, subrule 22.4(1), submitted on May 7, 1990, 
incorporates by reference revised EPA Modeling Guideline Supplement A, 
July 1987, and recodified air quality rules chapter 20-29.
    (i) Incorporation by reference.
    (A) Amendment to chapter 22, ``Controlling Pollution,'' Iowa 
Administrative Code, subrule 22.4(1). Effective March 14, 1990.
    (B) Recodification of Iowa Administrative Code, title II--Air 
Quality, chapters 20-29, effective December 3, 1986.
    (53) Revised chapter 22, rule 22.4(455B), submitted on November 8, 
1990, incorporates by reference revised EPA PSD rules pertaining to NO 
x increments.
    (i) Incorporation by reference.
    (A) Amendment to chapter 22, ``Controlling Pollution,'' Iowa 
Administrative Code, subrule 22.4, adopted by the Environmental 
Protection Commission on October 17, 1990, effective November 21, 1990.
    (ii) Additional material
    (A) Letter from the state dated November 8, 1990, pertaining to NO 
x rules and analysis which certifies the material was adopted 
by the state on October 17, 1990.
    (54) On March 13, 1991, the Iowa Department of Natural Resources 
(IDNR) submitted a plan revision pertaining to major SO2 
sources in Clinton County, Iowa.
    (i) Incorporation by reference. (A) Administrative Consent Order 
90-AQ-10, signed by Larry Wilson, Director, IDNR, dated July 5, 1990, 
and revision dated March 25, 1991. Also, three letters to Archer-
Daniels-Midland (ADM) Company dated June 20, 1990, signed by Michael 
Hayward, IDNR, which contain or reference new or revised permit 
conditions for ADM sources, and a letter to ADM from IDNR dated February 
26, 1991, correcting certain permit provisions.
    (B) Administrative Consent Order 89-AQ-04, signed by Larry Wilson, 
Director, IDNR, dated February 21, 1990. Also, two letters to Interstate 
Power Company dated January 25 and 29, 1990, and signed by Michael 
Hayward, IDNR, which contain supplemental permit condition for permits 
74-A-117-S and 78-A-157-S.
    (ii) Additional material. (A) Letter and supplemental material from 
Larry J. Wilson to Morris Kay dated March 13, 1991.
    (55) Revised Polk County, Iowa Board of Health Rules and 
Regulations, chapter V, Air Pollution, submitted by the Iowa Department 
of Natural Resources on May 23, 1991.
    (i) Incorporation by reference. (A) Polk County Board of Health 
Rules and Regulations, chapter V, Air Pollution, Ordinances 28, 72 and 
85, effective May 1, 1991, except for the following: Article I, 
definition of variance; Article VI, Section 5-16 (n), (o), and (p); 
Article VI, Section 5-17(d), variance provision; Article VIII; Article 
IX, Sections 5-27(3) and 5-27(4); and Article X, Division 5--Variance.
    (ii) Additional material. (A) Letter from Allan Stokes to William A. 
Spratlin dated October 23, 1991.
    (56) Revised Chapter 23, rule 23.2, submitted on October 3, 1991, 
incorporates changes to the open burning rule.
    (i) Incorporation by reference.
    (A) Amendment to Chapter 23, ``Emission Standards for Contaminants, 
``Iowa Administrative Code,

[[Page 479]]

subrule 23.2, adopted by the Environmental Protection Commission, 
effective September 12, 1990.
    (ii) Additional information.
    (A) Letter from Allan Stokes, IDNR, to William Spratlin, dated 
October 3, 1991.
    (57) On January 5, 1993, the Iowa Department of Natural Resources 
(IDNR) submitted air quality rule revisions to Iowa Administrative Code, 
Chapters 20, 22, 23, 24, 25, 29, and revisions to the Compliance 
Sampling Manual.
    (i) Incorporation by reference.
    (A) Revisions to Chapter 20 (20.2), Scope of Title-Definitions-
Forms-Rules of Practice; Chapter 22 (22.3(1), 22.4, 22.5(2)), 
Controlling Pollution; Chapter 23 (23.2(3), 23.3(2), 23.3(3), 23.4(12)), 
Emission Standards for Contaminants; Chapter 24 (24.1(1), 24.1(5)), 
Excess Emission; Chapter 25, (25.1(7), 25.1(9)), Measurement of 
Emissions and rescind 25.1(10)d; and Chapter 29 (29.1), Qualification in 
Visual Determination of the Opacity of Emissions. These revisions were 
adopted by the Iowa Environmental Protection Commission on December 21, 
1992, and became effective on February 24, 1993.
    (ii) Additional material.
    (A) Letter from Larry Wilson, IDNR, to Morris Kay, EPA, dated 
January 5, 1993, and the Compliance Sampling Manual, revised December 
1992.
    (58) A plan for implementation of the Small Business Stationary 
Source Technical and Environmental Compliance Assistance Program was 
submitted by the Iowa Department of Natural Resources as a revision to 
the Iowa SIP on December 22, 1992.
    (i) Incorporation by reference.
    (A) Revisions to the Iowa State Implementation Plan for the Small 
Business Stationary Source Technical and Environmental Compliance 
Assistance Program dated December 1992.
    (59) On May 5, 1994, the Director of the Iowa Department of Natural 
Resources submitted revisions to the State Implementation Plan (SIP) to 
update the state's incorporation by reference and conformity to various 
federally approved regulations.
    (i) Incorporation by reference.
    (A) Revised rules, ``Iowa Administrative Code,'' effective January 
12, 1994. This revision approves an amendment to paragraph 23.2(3)g 
pertaining to open fires burned for the purpose of training fire-
fighting personnel.
    (B) Revised rules, ``Iowa Administrative Code,'' effective April 20, 
1994. This revision approves amendments to rules 22.4; 23.3(2)d (3) and 
(4); 23.4(6); and 25.1(9). These rules concern the update of the state's 
incorporation of prevention of significant deterioration and test method 
requirements.
    (ii) Additional material. None.
    (60) On May 5, 1994, the Director of the Iowa Department of Natural 
Resources submitted revisions to the State Implementation Plan (SIP) to 
update the state's incorporation by reference and conformity to various 
Federally approved regulations.
    (i) Incorporation by reference.
    (A) Revised rules, ``Polk County Ordinance No. 132--Polk County 
Board of Health Rules and Regulations,'' effective December 2, 1993. 
This revision approves all articles in Chapter V, except for Article VI, 
Section 5-16(n) and (p), Article VIII, and Article XIII.
    (ii) Additional material.
    (A) None.
    (61) On October 18, 1994, and January 26, 1995, the Director of the 
Iowa Department of Natural Resources submitted revisions to the state 
implementation plan (SIP) to include special requirements for 
nonattainment areas, provisions for use of compliance, and enforcement 
information and adoption of EPA definitions. These revisions fulfill 
Federal regulations which strengthen maintenance of established air 
quality standards.
    (i) Incorporation by reference.
    (A) Revised rules ``Iowa Administrative Code,'' effective November 
16, 1994. This revision approves revised rules 567-20.2, 567-22.5(1)a, 
567-22.5(1)f(2), 567-22.5(1)m, 567-22.5(2), 567-22.5(3), 567-22.5(4)b, 
567-22.5(6), 567-22.5(7), 567-22.105(2), and new rule 567-21.5. These 
rules provide for special requirements for nonattainment areas, 
provisions for use of compliance and enforcement information and adopts 
EPA's definition of volatile organic compound.
    (B) Revised rules, ``Iowa Administrative Code,'' effective February 
22, 1995. This revision approves new definitions to rule 567-20.2. This 
revision adopts

[[Page 480]]

EPA's definitions of ``EPA conditional method'' and ``EPA reference 
method.''
    (ii) Additional material.
    None.
    (62)  [Reserved]
    (63) On December 8, 1994; February 16, 1996; and February 27, 1996, 
the Director of the Iowa Department of Natural Resources submitted 
revisions to the State Implemenation Plan (SIP) to create a voluntary 
operating permit program as an alternative to Title V. These revisions 
strengthen maintenance of established air quality standards.
    (i) Incorporation by reference.
    (A) ``Iowa Administrative Code,'' sections 567-22.200-22.208, 
effective December 14, 1994. These rules create the voluntary operating 
permit program.
    (B) ``Iowa Administrative Code,'' sections 567-22.201(1)``a'' and 
22.206(1)``h'', effective January 11, 1995.
    (C) ``Iowa Administrative Code,'' section 567-22.203(1)``a''(1), 
effective February 24, 1995.
    (D) ``Iowa Administrative Code,'' sections 567-20.2; 22.200; 
22.201(1)``a'' and ``b''; 22.201(2)``a''; and 22.206(2)``c'', effective 
October 18, 1995.
    (ii) Additional material.
    (A) Letter from Allan E. Stokes, Iowa Department of Natural 
Resources, to William A. Spratlin, U.S. EPA, dated February 16, 1995. 
This letter outlines various commitments by the state to meet 
requirements outlined by the EPA.
    (64) In correspondence dated February 16, 1996, February 19, 1996, 
and February 27, 1996, the Director of the Iowa Department of Natural 
Resources (IDNR) submitted revisions to the State Implementation Plan 
concerning open burning, new source review (NSR) requirements for 
nonattainment areas, test method and definition updates.
    (i) Incorporation by reference.
    (A) ``Iowa Administrative Code,'' section 567-22.8(1), effective 
July 12, 1995, containing a permit by rule for spray booths.
    (B) ``Iowa Administrative Code,'' sections 567-23.2(3); 23.2(4), 
effective April 19, 1995, addressing open burning.
    (C) ``Iowa Administrative Code,'' sections 567-22.5 (2)-(6), (8)-
(10), effective March 20, 1996. These rules address NSR requirements in 
nonattainment areas.
    (D) ``Iowa Administrative Code,'' sections 567-20.2; 22.4(1); and 
25.1(9), effective July 12, 1995. These rules address test method and 
definition updates.
    (E) ``Iowa Administrative Code,'' section 567-31.1, effective 
February 22, 1995. This rule addresses permit requirements relating to 
nonattainment areas.
    (ii) Additional material.
    (A) Letter dated July 11, 1997, from Pete Hamlin, IDNR, to Wayne 
Leidwanger, EPA, requesting approval under 112(l).
    (65) On June 13, 1996, and April 25, 1997, the Director of the Iowa 
Department of Natural Resources (IDNR) submitted a revision to the State 
Implementation Plan (SIP) which included permits containing source 
specific emission limits and conditions for three sources in Muscatine, 
Iowa.
    (i) Incorporation by reference.
    (A) Grain Processing Corporation permits 95-A-374, 74-A-015-S, 
79-A-194-S, 79-A-195-S, signed September 18, 1995.
    (B) Muscatine Power and Water permits 74-A-175-S, 95-A-373 signed 
September 14, 1995.
    (C) Monsanto Corporation permits 76-A-265S3, 76-A-161S3, signed 
July 18, 1996.
    (ii) Additional material.
    (A) Letters from Allan E. Stokes, IDNR, to Dennis Grams, 
Environmental Protection Agency, dated June 13, 1996, and April 21, 
1997, containing supporting SIP information.
    (66) On April 2, 1997, the Director of the Iowa Department of 
Natural Resources submitted revisions to the State Implementation Plan 
(SIP) for the State's two local agencies: the Polk County Public Works 
Department and Linn County Health Department.
    (i) Incorporation by reference.
    (A) Revised rules, ``Polk County Board of Health Rules and 
Regulations: Chapter V, Air Pollution,'' effective December 18, 1996. 
This revision approves all articles insofar as they pertain to the SIP. 
Article XIII is specifically excluded from this approval. No action is 
taken on Sections 5-16(n), 5-16(p), 5-20, and 5-27(3) and (4).
    (B) Revised rules, ``Linn County Air Pollution Control Code of 
Ordinances,'' effective March 7, 1997. This revision

[[Page 481]]

approves all sections insofar as they pertain to the SIP. Sections 
10.4(1.), 10.11, and 10.15 are specifically excluded from this approval. 
No action is taken on Sections 10.9(2.), 10.9(3.), 10.9(4.), and the 
definition of ``federally enforceable'' in Section 10.2.
    (ii) Additional material.
    (A) Letter from Allan E. Stokes, Iowa Department of Natural 
Resources, to William A. Spratlin, Environmental Protection Agency, 
dated May 15, 1997. This letter provides additional information 
regarding various administrative requirements outlined in 40 CFR part 
51.
    (67) In correspondence dated Octoer 21, 1997, and January 21, 1998, 
the Director of the Iowa Department of Natural Resources submitted 
revisions to the State Implementation Plan.
    (i) Incorporation by reference.
    (A) ``Iowa Administrative Code'' sections567-22.8(1) ``b,'' ``c,'' 
and ``e,''567-22.203(1) ``a,'' 567-22.300, 567-22.300(1) through 567-
22.300(11), 567-23.3(2) ``d,'' and 567-29.1, effective June 12, 1996.
    (B) ``Iowa Administrative Code''section 567-20.2, effective October 
16, 1996.
    (C) ``Iowa Administrative Code'' sectuibs 567-22.300(40 ``b''(1), 
567-22.300(8) ``a''(1), and 567-22.300(8)``b''(2), effective December 
25, 1996.(D) ``Iowa Administrative Code'' sections 567-20.2, 567-
22.2(1), 567-22.201(1) ``a,'' 567-22.201(2) ``b,'' 567-22.202, 567-
22.203(1), 567-22.300(3) ``b'' and ``c,'' 567-22.300(8) ``a,'' effective 
May 14, 1997.
    (ii) Additional material.
    (A) ``Iowa Administrative Code'' section 567-23.1(5), Calculation of 
emission limitations based upon stack height, was renumbered to section 
567-23.1(6), effective August 20, 1997.
[37 FR 10865, May 31, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.820, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.

    Effective Date Note:  At 63 FR 34602, June 25, 1998, Sec. 52.820 was 
amended by adding paragraph (c)(67), effective Aug. 24, 1998.



Sec. 52.821  Classification of regions.

    The Iowa plan was evaluated on the basis of the following 
classification:

----------------------------------------------------------------------------------------------------------------
                                                                               Pollutant
                                                      ----------------------------------------------------------
              Air quality control region                                                           Photochemical
                                                       Particulate   Sulfur   Nitrogen   Carbon      oxidants
                                                          matter     oxides    dioxide  monoxide  (hydrocarbons)
----------------------------------------------------------------------------------------------------------------
Metropolitan Omaha-Council Bluffs Interstate.........           I         II       III       III           III
Metropolitan Sioux Falls Interstate..................          II        III       III       III           III
Metropolitan Sioux City Interstate...................         III        III       III       III           III
Metropolitan Dubuque Interstate......................           I        III       III       III           III
Metropolitan Quad Cities Interstate..................           I        III       III       III           III
Burlington-Keokuk Interstate.........................           I          I       III       III           III
Northwest Iowa Intrastate............................         III        III       III       III           III
North Central Iowa Intrastate........................          IA        III       III       III           III
Northeast Iowa Intrastate............................           I        III       III       III           III
Southwest Iowa Intrastate............................         III        III       III       III           III
South Central Iowa Intrastate........................           I        III       III       III             I
Southeast Iowa Intrastate............................         III        III       III       III           III
----------------------------------------------------------------------------------------------------------------

[37 FR 10865, May 31, 1972, as amended at 39 FR 16346, May 8, 1974]



Sec. 52.822  Approval status.

    (a) With the exceptions set forth in this subpart, the Administrator 
approves Iowa's plan for the attainment and maintenance of the national 
standards. Further, the Administrator finds the plan satisfies all 
requirements of Part D, Title I, of the Clean Air Act as amended in 
1977, except as noted below.
[45 FR 14567, Mar. 6, 1980, as amended at 46 FR 47546, Sept. 29, 1981]

[[Page 482]]



Sec. 52.823  PM10 State Implementation Plan Development in Group II Areas.

    The Iowa Department of Natural Resources committed to comply with 
the PM10 regulations as set forth in 40 CFR part 51. In a 
letter to Morris Kay, EPA, dated October 28, 1988, Mr. Larry J. Wilson, 
Director, Iowa Department of Natural Resources, stated:

    Three groups within the State of Iowa have been classified as Group 
II areas for fine particulate (PM-10) State Implementation Plan (SIP) 
development purposes. This includes portions of the cities of Des 
Moines, Mason City, and Cedar Rapids. The specific boundaries of these 
areas were identified in a letter of October 13, 1987, from Peter R. 
Hamlin to Carl Walter. The remainder of the State was classified as 
Group III.
    In accordance with the SIP development procedures identified in the 
preamble of the PM-10 regulations for Implementing Revised Particulate 
Matter Standards, promulgated July 1, 1987, the State of Iowa commits to 
perform the following activities in these three Group II areas of the 
state:

    (a) Gather ambient PM-10 data, to an extent consistent with minimum 
EPA requirements (note the network description contained in a letter of 
January 26, 1988, from Peter R. Hamlin to John Helvig).
    (b) Analyze and verify the ambient PM-10 data and report exceedances 
of the 24-hour PM-10 National Ambient Air Quality Standards (NAAQS) to 
the Regional Office within 60 days of each exceedance.
    (c) Immediately notify the Regional Office:
    (1) Upon the availability of an appropriate number of verifiable 24-
hour NAAQS exceedances to indicate a violation (see Section 2.0 of the 
PM-10 SIP development guideline) or
    (2) when an annual arithmetic mean (AAM) above the annual PM-10 
NAAQS becomes available.
    (d) Within thirty (30) days of any notification of the Regional 
Office pursuant to (c) above (or upon collection of thirty-six (36) 
months of PM-10 ambient air quality data acceptable to EPA, whichever 
comes first) determine whether the measures in the existing SIP will 
assure timely attainment and maintenance of the primary PM-10 NAAQS and 
immediately notify the Regional Office of the results of this 
determination.
    (e) Within six (6) months of any notification pursuant to (d) above, 
adopt and submit to EPA a PM-10 control strategy that assures attainment 
as expeditiously as practicable but not later than three (3) years from 
approval of the Committal SIP.

    Because of the uncertainty about when the determination can be made 
pursuant to (d) above, it is difficult to determine if that control 
strategy could provide for the attainment of the PM-10 NAAQS within 
three years from the date EPA approves thisCommittal SIP. Therefore, I 
reserve the right to request a two-year extension of the attainment date 
as provided in Section 110(e) of the Clean Air Act, if and when the 
State of Iowa submits a SIP revision for any of these areas of the 
state.
    The State of Iowa also commits to develop a PM-10 emission inventory 
for the areas submitted as part of any PM-10 SIP pursuant to items (c), 
(d), and (e) above. If the PM-10 NAAQS are not violated, the State of 
Iowa will proceed with this inventory for the three Group II areas in 
accordance with the following schedule:

    October 1, 1988--Request special assistance funds from EPA to 
perform the inventory.
    October 1, 1989--Initiate inventory.
    August 1, 1990--Complete inventory.
    October 31, 1990 *--Submit inventory as part of a determination of 
adequacy that the current SIP will attain and maintain the PM-10 NAAQS.


    * Presuming that sufficient ambient data acceptable to EPA are 
collected by July 31, 1990, and available by September 30, 1990.
---------------------------------------------------------------------------

[54 FR 33539, Aug. 15, 1989]



Sec. 52.824  [Reserved]



Sec. 52.825  Compliance schedules.

    (a) [Reserved]
    (b) Regulation for increments of progress. (1) Except as provided in 
paragraph (b)(2) of this section, the owner or operator of any 
stationary source subject to regulation 4.3.(3)(b), ``Rules and 
Regulations Relating to Air Pollution Control of the Iowa Air Pollution 
Control Commission'' shall, no later than December 31, 1972, submit to 
the Administrator for approval, a proposed compliance schedule that 
demonstrates compliance with the applicable regulation as expeditiously 
as practicable but no later than January 1, 1975. The compliance 
schedule shall provide for periodic increments of progress towards 
compliance. The dates for achievement of such increments shall be 
specified. Increments of progress shall include, but not be limited to: 
Letting of necessary contract for construction or process changes, if 
applicable; initiation of construction; completion and start-up of 
control system; performance tests; and submittal of performance test 
analysis and results.

[[Page 483]]

    (2) Where any such owner or operator demonstrates to the 
satisfaction of the Administrator that compliance with the applicable 
regulations will be achieved on or before December 31, 1973, no 
compliance schedule shall be required.
    (3) Any owner or operator who submits a compliance schedule pursuant 
to this paragraph shall, within 5 days after the deadline for each 
increment of progress, certify to the Administrator whether or not the 
required increment of the approved compliance schedule has been met.
    (4) Any compliance schedule adopted by the State and approved by the 
Administrator shall satisfy the requirements of this paragraph for the 
affected source.
    (c) The compliance schedules for the sources identified below are 
approved as revisions to the plan pursuant to Sec. 51.104 and subpart N 
of this chapter. All regulations cited are air pollution control 
regulations of the State, unless otherwise noted.

                                                                          Iowa
--------------------------------------------------------------------------------------------------------------------------------------------------------
                                                                                                             Variance expiration
               Source                       Location           Regulation involved        Date adopted               date          Final compliance date
--------------------------------------------------------------------------------------------------------------------------------------------------------
Iowa Army Ammunition Plant           Middletown, Iowa......  400--4.2(1)...........  June 14, 1979........  Feb. 28, 1982........  Feb. 1982.
 (explosive contaminated waste
 burning).
Progressive Foundry, Inc., cupola    Perry.................  400-4.6...............  Nov. 6, 1981.........  .....................  Sept. 1, 1983.
 and casting shakeout area.
--------------------------------------------------------------------------------------------------------------------------------------------------------
Note 1: Linn County Health Department does not issue variances if source(s) is on an approvable compliance schedule.
Note 2: Polk County Department of Health does not issue variances if source(s) is on an accepted and approved compliance schedule.
Note 3: City of Des Moines, Department of Public Health does not issue variances if source(s) is on an accepted and approved compliance schedule.

[37 FR 10865, May 31, 1972]


    Editorial Note: For Federal Register citations affecting 
Sec. 52.825, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Secs. 52.826--52.827  [Reserved]



Sec. 52.828  Enforcement.

    (a) Sections 23(1)(b) and 13(7) of Senate File 85, Division II for 
Iowa are disapproved insofar as they permit the Air Quality Commission 
of the Iowa Department of Environmental Quality to issue abatement 
orders (1) that defer compliance with plan requirements beyond the dates 
required for attainment of the national standards, (2) without the 
approval of the Administrator, and (3) for reasons not permitted by the 
Clean Air Act.
    (b) Regulation limiting administrative abatement orders:
    (1) No order deferring compliance with a requirement of the Iowa 
Implementation Plan shall be issued by the Air Quality Commission of the 
Iowa Department of Environmental Quality which does not meet the 
following requirements:
    (i) An order must require compliance with the plan requirement 
within the times and under the conditions specified in Sec. 51.261 (a) 
and (b) of this chapter.
    (ii) An order may not defer compliance beyond the last date 
permitted by section 110 of the Act for attainment of the national 
standard which the plan implements unless the procedures and conditions 
set forth in section 110(f) of the Act are met.
    (iii) An order shall not be effective until it has been submitted to 
and approved by the Administrator in accordance with Secs. 51.104, 
51.105, 51.261 and 51.262(a).
    (2) Notwithstanding the limitations of paragraph (b)(1)(ii) of this 
section, an order may be granted which provides for compliance beyond 
the statutory attainment date for a national standard where compliance 
is not possible because of breakdowns ormalfunctions of equipment, acts 
of God, or other unavoidable occurrences. However, such order may not 
defer compliance for more than three (3)

[[Page 484]]

months unless the procedures and conditions set forth in section 110(f) 
of the Act are met.
[38 FR 30877, Nov. 8, 1973, as amended at 51 FR 40675, 40676, 40677, 
Nov. 7, 1986; 52 FR 24367, June 30, 1987]



Secs. 52.829--52.832  [Reserved]



Sec. 52.833  Significant deterioration of air quality.

    (a) The requirements of sections 160 through 165 of the Clean Air 
Act are met, except for sources seeking permits to locate on Indian 
lands in the state of Iowa; sources with permits issued by EPA prior to 
the effective date of the state's rules; and certain sources affected by 
the stack height rules described in a letter from Iowa dated April 22, 
1987.
    (b) Regulations for preventing significant deterioration of air 
quality.
    The provisions of Sec. 52.21 (b) through (w) are hereby incorporated 
and made a part of the applicable state plan for the state of Iowa for 
sources wishing to locate on Indian lands; sources constructed under 
permits issued by EPA; and certain sources as described in Iowa's April 
22, 1987, letter.
[52 FR 23982, June 26, 1987]



Sec. 52.834  Control strategy: Sulfur dioxide.

    Approval--On April 21, 1997, the Iowa Department of Natural 
Resources (IDNR) submitted a maintenance plan and redesignation request 
for the Muscatine County nonattainment area. The maintenance plan and 
redesignation request satisfy all applicable requirements of the Clean 
Air Act.
[63 FR 13345, Mar. 19, 1998]



                            Subpart R--Kansas



Sec. 52.870  Identification of plan.

    (a) Title of plan: ``State of Kansas Implementation Plan for the 
Attainment and Maintenance of National Air Quality Standards.''
    (b) The plan was officially submitted on January 31, 1972.
    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) Various comments on the plan in response to the Regions review 
were submitted on March 24, 1972, by the State Department of Health. 
(Non-regulatory)
    (2) The Emergency Episode Operations/Communications Manual for the 
Kansas City Interstate AQCR was submitted on April 6, 1972, by the State 
Department of Health. (Non-regulatory)
    (3) Emergency Episode Operations/Communications Manual for all 
Kansas Intrastate AQCR's was submitted on February 15, 1973, by the 
State Department of Health. (Non-regulatory)
    (4) Revisions of sections 28-19-6 through 15, 20-24, 30-32, 40-47, 
50-52 and 55-58 of the State air pollution control regulations were 
submitted by the State Department of Health on April 17, 1973.
    (5) Letter from the Governor, dated May 29, 1973, concerning the 
attainment of CO emission standards. (Non-regulatory)
    (6) An amendment to the State air quality control law, Senate Bill 
No. 30, dealing with public access to emission data was submitted on 
July 27, 1973, by the Governor.
    (7) Revisions of sections 28-19-8, 9, 14, 22, 25 and and 47 of the 
State air pollution control regulations were submitted on February 6, 
1974, by the Governor.
    (8) Copy of the State's analysis and recommendations concerning the 
designation of Air Quality Maintenance Areas was submitted by letter 
from the State Department of Health on February 28, 1974. (Non-
regulatory)
    (9) Kansas submitted State Implementation Plan (SIP) revisions to 
attain the National Ambient Air Quality Standards on September 17, 1979 
for Wyandotte and Johnson Counties, on October 22, 1979 for Douglas 
County, and on March 10, 1980 for Kansas City of the state designated 
nonattainment areas under section 107 of the Clean Air Act as amended in 
1977. On September 22 and 25, 1980, the state submitted revised 
regulations on the control of volatile organic compounds and a 
regulation on the new source permit review program. Included in the plan 
are the following approved state air pollution control regulations:
    (i) The VOC regulations which EPA approved as RACT: 28-19-61 
Definitions,

[[Page 485]]

28-19-62 Testing Procedures, 28-19-63 Automobile and Light Duty Trunk 
Surface Coating, 28-19-65 Petroleum Liquid Storage Tanks, 28-19-66 
Petroleum Liquid Storage in External Floating Roof Tanks, 28-19-67 
Petroleum Refineries, 28-19-68 Leaks from Petroleum Refinery Equipment, 
28-19-69 Cutback Asphalt.
    (ii) The New Source Permit Review regulation 28-19-16 through 16m 
which EPA conditionally approved as meeting the requirements of sections 
172(b)(6); 172(b)(11)(A), and 173.
    (iii) The Kansas City-Wyandotte County air pollution control 
regulations which have been adopted by both the Kansas City, Kansas 
Board of City Commissioners and the Wyandotte County Board of County 
Commissioners:

    2A-1 Jurisdiction, 2A-2 Purpose, 2A-3 Definitions, 2A-4 Powers of 
the Board, 2A-5 Facts and Circumstances Pertinent to Orders of Joint 
Board, 2A-6 Right of Entry for Inspection, 2A-7 Time for Compliance 
Schedule, 2A-8 Variance, 2A-9 Circumvention of Chapter or Regulations, 
2A-10 Air Pollution Nuisances Prohibited; Additional Emission 
Restrictions; Interference with the Enjoyment of Life and Property, 2A-
11 Reserved, 2A-12 Confidential Information, 2A-13 Registration and 
Permit System; Exemptions, 2A-14 Review of New or Altered Sources, 2A-15 
Public Hearings, 2A-16 Installations in which Fuel is Burned, 2A-17 
Restriction of Emission of Particulate Matter from Industrial Processes, 
2A-18 Open Burning Prohibition, 2A-19 Opacity Requirements, 2A-20 
Exceptions Due to Breakdowns or Scheduled Maintenance, 2A-21 Preventing 
Particulate Matter from Becoming Air-Borne, 2A-22 Measurement of 
Emissions, 2A-23 Restriction of Emission of Odors, 2A-24 Sulfur Compound 
Emissions, 2A-24.1 Hydrocarbon Emissions; Stationary Sources, 2A-25 
Control of Carbon Monoxide Emissions, 2A-26 Control of Nitrogen Oxide 
Emissions, 2A-26.1 Incinerators, 2A-27 Air Pollution Emergencies--
General Provisions, 2A-28 Air Pollution Emergencies--Episode Criteria, 
2A-29 Emission Reduction Requirements, 2A-30 Emergency Episode Plans, 
2A-31 Penalties for Violation of Chapter or Air Pollution Control 
Regulations, and 2A-32 Conflict of Ordinances, Effect Partial 
Invalidity.

    (10) The Kansas State Implementation Plan for lead was submitted on 
February 17, 1981, by the Governor of Kansas, along with a submittal 
letter which provided additional information concerning the Kansas State 
Implementation Plan for lead.
    (11) Kansas submitted SIP revisions to attain and maintain the 
National Ambient Air Quality Standards for carbon monoxide on April 16, 
1981, for the South Central Kansas Interstate Air Quality Control 
Region, Wichita nonattainment area. The plan included commitments to 
complete transportation control measures for the reduction of carbon 
monoxide from transportation related sources for the attainment of the 
national standards by December 31, 1982.
    (12) A plan revision which makes modifications to the existing 
Kansas air quality surveillance network was submitted by the Kansas 
Department of Health and Environment on October 16, 1981.
    (13) Additional information to correct two plan deficiencies was 
submitted by the Kansas Department of Health and Environment on May 12, 
1981.
    (14) Letter and supporting documents submitted on September 15, 
1981, from the Director of Air Quality and Occupational Health relating 
to reasonably available control technology for certain particulate 
matter sources in the Kansas City, Kansas area.
    (15) New regulations 28-19-70 and 28-19-62 applicable to tank trucks 
operating at bulk gasoline terminals were submitted by the Kansas 
Department of Health and Environment on June 15, 1982. State regulation 
28-19-51 is revoked. Revised regulations 28-19-16, 28-19-16a, 28-19-16b, 
28-19-16c, 28-19-16f, 28-19-16g, 28-19-16h, and 28-19-16i, applicable to 
new sources in nonattainment areas were included with the June 15, 1982 
submittal. Action is deferred on the following regulations: 28-19-
16a(d), 28-19-16a(v), 28-19-16, 28-19-16b, 28-19-16c, 28-19-16f, 28-19-
16h, 28-19-16i, and 28-19-16a(o). The remainder of the provisions are 
approved.
    (16) New regulations K.A.R. 28-19-17 through K.A.R. 28-19-171 
applicable to stationary sources subject to prevention of significant 
deterioration (PSD) permit requirements were submitted on May 5, 1983. 
Regulation K.A.R. 28-19-171 pertaining to the use of innovative control 
technology is not approved. By letter dated June 20, 1984,

[[Page 486]]

the State of Kansas agrees to follow the EPA interim stack height policy 
for each PSD permit issued until such time as EPA revises its general 
stack height regulations.
    (17) Revised regulation K.A.R. 28-19-69, applicable to the use of 
cutback asphalt, was submitted by the Secretary of the Kansas Department 
of Health and Environment on February 21, 1986.
    (i) Incorporation by reference.
    (A) Revised regulation K.A.R. 28-19-69 as approved by the Kansas 
Attorney General on December 5, 1985.
    (18) Revised regulations K.A.R. 28-19-63 applicable to automobile 
and light-duty truck surface coating; K.A.R. 28-19-64 applicable to bulk 
gasoline terminals; K.A.R. 28-19-67 applicable to petroleum refineries; 
and K.A.R. 28-19-68 applicable to leaks at petroleum refineries, were 
submitted by the Secretary of the Kansas Department of Health and 
Environment on February 21, 1986.
    (i) Incorporation by reference. (A) Revised regulations K.A.R. 28-
19-63, K.A.R. 28-19-64, K.A.R. 28-19-67, and K.A.R. 28-19-68 as approved 
by the Kansas Attorney General on October 30, 1985.
    (19) Revised Kansas regulations pertaining to fees for permits to 
construct and operate were submitted by the Kansas Department of Health 
and Environment on March 27, 1986.
    (i) Incorporation by reference.
    (A) Kansas Administrative Regulations (KAR) 28-19-7, 28-19-8, 28-19-
9, 28-19-14, 14(a) and 14(b), 28-19-31, 28-19-45, which became effective 
on May 1, 1986.
    (B) Letter of March 27, 1986 to EPA from the State of Kansas 
Department of Health and Environment.
    (C) Letter of September 15, 1987 to EPA from the State of Kansas 
Department of Health and Environment.
    (20) Revisions to the ozone attainment plan for the Kansas City 
metropolitan area were submitted by the Governor on July 2, 1986. 
Pursuant to this plan, revised regulations for the control of volatile 
organic compound emissions were submitted by the Secretary of the Kansas 
Department of Health and Environment on January 6, 1988. In numerous 
instances, the revised Kansas regulations provide for departmental 
discretion to approve compliance plans and test methods which are 
alternatives to the EPA reference methods. EPA approves these 
regulations with the understanding that all such alternative compliance 
plans and test methods must be submitted to EPA, and approved, as 
individual SIP revisions. In the absence of such approval, the 
enforceable requirements of the SIP shall be the emission limits or 
reduction requirements stated in the regulations. Also, the Kansas 
regulations contain provisions whereby testing is required when the 
facility intends to demonstrate compliance by improved operations or new 
emission controls, yet no test procedures are specified. Examples of 
such provisions are transfer efficiency (TE) and vapor processing 
systems. Test methods which are developed by the state must be approved 
by EPA before facilities may demonstrate compliance through alternative 
controls and/or TE.
    (i) Incorporation by reference.
    (A) Revised regulations K.A.R. 28-19-8, Reporting required; K.A.R. 
28-19-61, Definitions; K.A.R. 28-19-62, Testing procedures; K.A.R. 28-
19-63, Automobile and light-duty truck surface coating; K.A.R. 28-19-64, 
Bulk gasoline terminals; K.A.R. 28-19-65, VOC liquid storage in 
permanent fixed roof type tanks; K.A.R. 28-19-66, VOC liquid storage in 
external floating roof tanks; K.A.R. 28-19-69, Cutback asphalt; K.A.R. 
28-19-70, Leaks from gasoline delivery vessels and vapor collection 
systems; K.A.R. 28-19-71, Printing operations; K.A.R. 28-19-72, Gasoline 
dispensing facilities; K.A.R. 28-19-73, Surface coating of miscellaneous 
metal parts and products and metal furniture; K.A.R. 28-19-74, Wool 
fiberglass manufacturing; and K.A.R. 28-19-75, Solvent metal cleaning. 
Temporary versions of these regulations are effective December 16, 1987, 
through April 30, 1988. The permanent regulations are effective May 1, 
1988.
    (B) Letter of January 6, 1988, from the Secretary of the Kansas 
Department of Health and Environment. This letter establishes the 
effective dates for the revised regulations referenced in subparagraph 
(20)(i)(A) above.
    (ii) Additional material.

[[Page 487]]

    (A) State of Kansas Implementation Plan, Part A--Kansas City 
Metropolitan Area, Ozone, dated June 1986, submitted by the Governor on 
July 2, 1986. The plan contains an attainment demonstration, emissions 
inventories, and a control strategy.
    (B) Supplemental information, pursuant to the above referenced plan, 
was submitted on August 19, 1987.
    (C) Negative declarations for certain VOC source categories were 
submitted on April 16 and August 18, 1987.
    (21) Revised Kansas regulations applicable to air quality models and 
definitions were submitted by the Kansas Department of Health and 
Environment on January 6, 1988.
    (i) Incorporation by reference.
    (A) Kansas Administrative Regulations (K.A.R.) 28-19-17(f) and 28-
19-7 (a) through (f) and (h) through (w) which became effective December 
16, 1987. EPA is deferring action on 28-19-7(g), Emission Limitation and 
Standard.
    (22) On March 1, 1985, the Governor of Kansas submitted a revised 
carbon monoxide state implementation plan for Wichita, Kansas. On 
September 3, 1987, the Kansas Department of Health and Environment 
submitted two new transportation control measures as part of the revised 
Wichita carbon monoxide control plan.
    (i) Incorporation by reference. (A) Letter of September 3, 1987, 
from the Kansas Department of Health and Environment and attached 
transportation control measures adopted August 18, 1987.
    (B) Revision of the Wichita-Sedgwick County Portion of the Kansas 
State Implementation Plan for Carbon Monoxide submitted by the Governor 
on March 1, 1985. The plan contains an attainment demonstration, 
emissions inventory, and a control strategy.
    (23) Kansas Administrative Regulations (K.A.R.) 28-19-19(a) through 
28-19-19(o) pertaining to continuous emission monitoring at certain 
stationary sources were submitted on January 6, 1988, by the Kansas 
Department of Health and Environment. K.A.R. 28-19-19(o) allows for 
departmental discretion on use of different but equivalent procedures 
than those specified in 28-19-19(a) through 28-19-19(n). EPA approves 
this rule with the understanding that all such equivalent procedures and 
requirements must be submitted to EPA as individual SIP revisions. In 
the absence of such approval, the enforceable provisions of K.A.R. 28-
19-19(a) through 28-19-19(n) shall be applicable.
    (i) Incorporation by reference. (A) K.A.R. 28-19-19(a) through 28-
19-19(o), continuous emission monitoring, as submitted by the Secretary 
of the Kansas Department of Health and Environment. These regulations 
became effective on May 1, 1988.
    (B) Letter of January 6, 1988, from the Secretary of the Kansas 
Department of Health and Environment. This letter establishes the 
effective date for the revised regulations referenced in paragraph 
(23)(i)(A) of this section.
    (24) Revised regulations K.A.R. 28-19-7(g), K.A.R. 28-19-16, and 
K.A.R. 28-19-17 pertaining to new source permit requirements, were 
submitted by the Secretary of the Kansas Department of Health and 
Environment on March 27, 1986. Revised regulation K.A.R. 28-19-18 
pertaining to stack heights was submitted by the Secretary of the Kansas 
Department of Health and Environment on January 6, 1988.
    (i) Incorporation by reference.
    (A) Revised regulations, K.A.R. 28-19-16, 28-19-16b, 28-19-16d, 28-
19-16g, 28-19-16i, 28-19-161, 28-19-17, 28-19-17a, and 28-19-17b, which 
became effective on May 1, 1986.
    (B) Revised regulations K.A.R. 28-19-7(g), and K.A.R. 28-19-18 
through 28-19-18f. The temporary regulations became effective December 
16, 1987, and became permanently effective on May 1, 1988.
    (ii) Additional material.
    (A) KDHE letter of March 27, 1986, to EPA pertaining to new source 
permit regulations.
    (B) KDHE letter of January 6, 1988, and June 9, 1988, to EPA 
pertaining to stack height regulations.
    (C) KDHE letters of December 7, 1987, and December 23, 1987, 
pertaining to the state's stack heights analysis and negative 
declarations.
    (25) Revised Kansas Administrative Regulations (K.A.R.) pertaining 
to PM10 regulations and the PM10 committal SIP 
were submitted by Kansas on October 5, 1989.

[[Page 488]]

    (i) Incorporation by reference. (A) Revised regulations Article 19--
Ambient Air Quality Standards and Air Pollution Control, K.A.R. 28-19-7, 
28-19-8, 28-19-14, 28-19-16a, 28-19-17a, 28-19-17b, 28-19-17c, 28-19-
17g, 28-19-17i, 28-19-20, 28-19-21, and 28-19-56, published August 31, 
1989, effective October 16, 1989.
    (ii) Additional material. (A) Letter of October 5, 1989, from the 
Secretary of the Kansas Department of Health and Environment (KDHE).
    (B) Memorandum of October 16, 1989, from the Secretary of State 
(Kansas) to Stanley Grant (KDHE).
    (C) Revised Air Quality Surveillance Monitoring Plan--Section E.
    (26) Revisions to the state implementation plan for the Kansas City 
metropolitan area were submitted by the Governor on October 23, 1991. 
Revisions include a maintenance plan which demonstrates continued 
attainment of the NAAQS for ozone through the year 2002. Rule revisions 
were also submitted on October 23, 1991.
    (i) Incorporation by reference,
    (A) Article 19--Ambient Air Quality Standards and Air Pollution 
Control, revised Kansas Administrative Regulations (K.A.R.) 28-19-61, 
Definitions, and K.A.R. 28-19-62, Testing procedures; and new rules 
K.A.R. 28-19-76, Lithography printing facilities, and K.A.R. 28-19-77, 
Chemical processing facilities that operate alcohol plants or liquid 
detergent plants. These rules were published August 22, 1991, and became 
effective October 7, 1991.
    (ii) Additional material
    (A) State of Kansas Implementation Plan, Kansas City Metropolitan 
Area Maintenance Provisions, October 1991.
    (27) On September 15, 1992, the Secretary of KDHE submitted rule 
revisions to K.A.R. 28-19-17, the PSD rule; to K.A.R. 28-19-19, the CEM 
rule; and to K.A.R. 28-19-73, a surface coating rule. These rule 
revisions were adopted by KDHE on April 3, 1992.
    (i) Incorporation by reference,
    (A) Revised regulations K.A.R. 28-19-17 through 28-19-171, K.A.R. 
28-19-19 and K.A.R. 28-19-73, and new regulations K.A.R. 28-19-17m 
through 28-19-17q, effective June 8, 1992.
    (ii) Additional material.
    (A) Letter and attachment from KDHE dated September 15, 1992 
pertaining to PSD NOx requirements.
    (28) A plan for implementation of the Small Business Stationary 
Source Technical and Environmental Compliance Assistance Program was 
submitted by the Kansas Department of Health and Environment as a 
revision to the Kansas State Implementation Plan (SIP) on January 25, 
1994.
    (i) Incorporation by reference.
    (A) Kansas SIP, Small Business Stationary Source Technical and 
Environmental Compliance Assistance Program, dated November 15, 1993.
    (29) On May 16, 1994 the Secretary of KDHE submitted revisions to 
rules K.A.R. 28-19-31, 28-19-32, 28-19-63, and operating permits 
#20090048 (BPU Quindaro station) and #20090049 (BPU Kaw station).
    (i) Incorporation by reference.
    (A) Revised regulations K.A.R. 28-19-31, K.A.R. 28-19-32, K.A.R. 28-
19-63, effective November 8, 1993.
    (B) Operating permits; Kansas City, Kansas, Board of Public 
Utilities Quindaro permit #20090048, and Kaw permit #20090049, effective 
October 20, 1993.
    (ii) Additional material.
    (A) Letter from BPU to KDHE dated December 11, 1992, regarding 
compliance verification methods and schedules.
    (30) On February 17, 1995, the Secretary of the Kansas Department of 
Health and Environment (KDHE) submitted for approval numerous rule 
revisions which add and revise definitions, revise the Kansas 
construction permit program, and create a class II operating permit 
program.
    (i) Incorporation by reference.
    (A) Revised rules K.A.R. 28-19-7 effective November 22, 1993; K.A.R. 
28-19-8 effective January 23, 1995; K.A.R. 28-19-14 effective January 
24, 1994; and the revocation of K.A.R. 28-19-14a effective January 23, 
1995; and the revocation of K.A.R. 28-19-14b effective January 24, 1994.
    (B) New rules K.A.R. 28-19-204, 212, 300, 301, 302, 303, 304, 400, 
401, 402, 403, 404, 500, 501, 502, 540, 541, 542, 543, 544, 545, 546, 
561, 562, and 563 effective January 23, 1995.

[[Page 489]]

    (31) On May 11, 1995, the Kansas Department of Health and 
Environment submitted an emissions inventory update to the Kansas City 
maintenance plan approved by EPA on June 23, 1992. The submittal also 
establishes a motor vehicle emissions budget for the purpose of 
fulfilling the requirements of the Federal Transportation Conformity 
rule.
    (i) Incorporation by reference.
    (A) Kansas City Ozone Maintenance State Implementation Plan 
Revision: Emissions Inventories and Motor Vehicle Emissions Budgets for 
the Kansas City Metropolitan Area, adopted on May 11, 1995.
    (32) A Plan revision was submitted by the Kansas Department of 
Health and Environment (KDHE) on June 6, 1996, which incorporates by 
reference the EPA's regulations relating to determining conformity of 
general Federal actions to State or Federal Implementation Plans, and 
which revokes old and adopts new open burning regulations.
    (i) Incorporation by reference.
    (A) Regulation K.A.R. 28-19-800, adopted by the Secretary of the 
KDHE on February 21, 1996, effective March 15, 1996.
    (B) Regulations K.A.R. 28-19-645 to K.A.R. 28-19-648, adopted by the 
Secretary of KDHE on February 6, 1996, effective March 1, 1996.
    (C) Regulations K.A.R. 28-19-45 to K.A.R. 28-19-47, revoked by the 
Secretary of KDHE on February 6, 1996, effective March 1, 1996.
    (33) A revision to the Kansas SIP was submitted by the Kansas 
Department of Health and Environment on May 23, 1997, pertaining to fuel 
volatility.
    (i) Incorporation by reference.
    (A) K.A.R. 28-19-79, Fuel Volatility, effective May 2, 1997.
    (d) Plan revisions were submitted on April 17, 1974, and February 
17, 1974.
[37 FR 10867, May 31, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.870, see the List of CFR Sections Affected in the Finding Aids 
sections of this volume.



Sec. 52.871  Classification of regions.

    The Kansas plan was evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                               Pollutant
                                                      ----------------------------------------------------------
              Air quality control region                                                           Photochemical
                                                       Particulate   Sulfur   Nitrogen   Carbon      oxidants
                                                          matter     oxides    dioxide  monoxide  (hydrocarbons)
----------------------------------------------------------------------------------------------------------------
Metropolitan Kansas City Interstate..................           I        III       III         I             I
South Central Kansas Intrastate......................           I        III       III       III             I
Northeast Kansas Intrastate..........................           I        III       III       III           III
Southeast Kansas Intrastate..........................         III        III       III       III           III
North Central Kansas Intrastate......................           I        III       III       III           III
Northwest Kansas Intrastate..........................           I        III       III       III           III
Southwest Kansas Intrastate..........................           I        III       III       III           III
----------------------------------------------------------------------------------------------------------------

[37 FR 10867, May 31, 1972]



Sec. 52.872  Operating permits.

    Emission limitations and related provisions which are established in 
Kansas operating permits as Federally enforceable conditions shall be 
enforceable by EPA. EPA reserves the right to deem permit conditions not 
Federally enforceable. Such a determination will be made according to 
appropriate procedures and be based upon the permit, permit approval 
procedures, or permit requirements which do not conform with the 
operating permit program requirements or the requirements of EPA 
underlying regulations.
[60 FR 36364, July 17, 1995]



Sec. 52.873  Approval status.

    (a) The Kansas portion of the Kansas City metropolitan area was 
designated as nonattainment for ozone in 40 CFR part 81. Therefore, the 
Administrator approves continuation of the 7.8 RVP limit as federally 
enforceable in the Kansas City metropolitan area, even

[[Page 490]]

after the area is redesignated to attainment, because of its 
nonattainment designation effective January 6, 1992. Also, the 
requirement for 7.8 psi RVP volatility is deemed necessary to ensure 
attainment and maintenance of the ozone standard as demonstrated by the 
emissions inventory projections (based on use of 7.8 psi RVP) in Kansas' 
ozone maintenance plan for the Kansas City metropolitan area.
    (b) [Reserved]
    (c) The Administrator approves Rule K.A.R. 28-19-31 as identified at 
Sec. 52.870(c)(29), with the understanding that any alternative 
compliance plans issued under this rule must be approved by EPA as 
individual SIP revisions.
[37 FR 10867, May 31, 1972, as amended at 46 FR 20170, Apr. 3, 1981; 46 
FR 61118, Dec. 15, 1981; 57 FR 27939, June 23, 1992; 59 FR 52427, Oct. 
18, 1994; 61 FR 16061, Apr. 11, 1996]



Sec. 52.874  Legal authority.

    (a) The requirements of Sec. 51.230(f) of this chapter are not met 
since authority to make emission data available to the public is 
inadequate. Kansas Statutes Annotated 65-3015 would require confidential 
treatment if the data related to processes or production unique to the 
owner or would tend to affect adversely the competitive position of the 
owner.
    (b) The requirements of Sec. 51.232(b) of this chapter are not met 
since the following deficiencies exist in the local agency legal 
authority:
    (1) Kansas City, Kans.-Wyandotte County Health Department. (i) 
Authority to make emission data available to the public is inadequate 
because the Kansas Statutes Annotated 65-3016 provides a designated 
local air quality conservation authority with the same authority as the 
State (Sec. 51.230(f) of this chapter).
    (2) Topeka-Shawnee County Health Department. (i) Authority to make 
emission data available to the public is inadequate because the Kansas 
Statutes Annotated 65-3016 provides a designated air quality 
conservation authority with the same authority as the State 
(Sec. 51.230(f) of this chapter).
    (3) Wichita-Sedgwick County Health Department. (i) Authority to make 
emission data available to the public is inadequate because the Kansas 
Statutes Annotated 65-3016 provides a designated local air quality 
conservation authority with the same authority as the State 
(Sec. 51.230(f) of this chapter).
    (c) The requirements of Sec. 51.230(d) of this chapter are not met 
since statutory authority to prevent construction, modification, or 
operation of a facility, building, structure, or installation, or 
combination thereof, which indirectly results or may result in emissions 
of any air pollutant at any location which will prevent the maintenance 
of a national air quality standard is not adequate.
[37 FR 10867, May 31, 1972, as amended at 39 FR 7281, Feb. 25, 1974; 51 
FR 40676, Nov. 7, 1986]



Sec. 52.875  [Reserved]



Sec. 52.876  Compliance schedules.

    (a) The requirements of Sec. 51.260 and of Sec. 51.15(a)(2) of this 
chapter as of September 19, 1976 (40 FR 43216), are not met since the 
plan does not contain legally enforceable compliance schedules setting 
forth the dates by which all stationary sources or categories of such 
sources must be in compliance with applicable portions of the control 
strategy. Paragraphs C and D of Kansas Regulation 28-19-9 specify that 
all sources not in compliance must submit an acceptable compliance 
schedule within 120 days after receiving notification from the State. 
There are no assurances that all sources will be notified by the State 
in a timely manner, therefore, paragraphs C and D of Regulation 28-19-9 
are disapproved.
    (b) Federal compliance schedule. (1) Except as provided in paragraph 
(2) of this paragraph (b), the owner or operator of any stationary 
source subject to any emission regulation which is part of the approved 
plan shall be in compliance on or before January 31, 1974.
    (i) Any owner or operator in compliance with any such applicable 
regulation on the effective date of this paragraph shall certify such 
compliance to the Administrator no later than December 31, 1972.
    (ii) Any owner or operator who achieves compliance with any such 
applicable regulation after the effective date of this paragraph shall 
certify such compliance to the Administrator

[[Page 491]]

within 5 days of the date compliance is achieved.
    (2) An owner or operator of a stationary source subject to any 
emission regulation approved by the Administrator may no later than 
December 31, 1972, submit to the Administrator for approval a proposed 
compliance schedule that demonstrates compliance with such regulation as 
expeditiously as practicable, but no later than July 31, 1975. The 
compliance schedule shall provide for periodic increments of progress 
toward compliance. The dates for achievement of such increments shall be 
specified. Increments of progress shall include, but not be limited to: 
Letting of necessary contracts for construction or process changes, if 
applicable; initiation of construction; completion and startup of 
control systems; performance tests; and submittal of performance test 
analysis and results.
    (3) Any owner or operator who submits a compliance schedule pursuant 
to this paragraph shall, within 5 days after the deadline for each 
increment of progress, certify to the Administrator whether or not the 
required increment of the approved compliance schedule has been met.
    (4) Any compliance schedule adopted by the State and approved by the 
Administrator shall satisfy the requirements of this paragraph for the 
affected source.
    (c) State compliance schedules. (1) [Reserved]
    (2) The compliance schedules identified below are disapproved as not 
meeting the requirements of Sec. 51.102 or subpart N of this chapter. 
All regulations cited are air pollution control regulations of the 
state, unless otherwise noted.

                                                     Kansas
----------------------------------------------------------------------------------------------------------------
                Source                         Location           Regulation involved          Date adopted
----------------------------------------------------------------------------------------------------------------
Chanute Manufacturing Co., Inc.: sand  Chanute................  28-19-50...............  Dec. 14, 1973.
 blasting.
Kansas City Power & Light, coal        LaCygne................  28-19-50...............  Nov. 22, 1974.
 transfer houses.
Pence Food Center, incinerator.......  Chanute................  28-19-40...............      Do.
Rodney Milling Co.:
  ``A'' house gallery and tunnel       Topeka.................  28-19-50...............      Do.
   system.
  ``B'' & ``C'' house gallery........  ......do...............  28-19-50...............      Do.
Western Alfalfa Corp., alfalfa         Deerfield..............  28-19-20...............      Do.
 dehydrator.
    Do...............................  Tice...................  28-19-20...............      Do.
Pence Food Center, incinerator.......  Humboldt...............  28-19-40...............      Do.
Sherwin-Williams Chemicals, Ozark      Coffeyville............  28-19-50B..............  Oct. 8, 1974.
 P.M. Mill.
Continental Grain Co., rail car        Hutchinson.............  28-19-50...............  Aug. 15, 1974.
 loading.
Far-Mar-Co, Inc., headhouse cyclones.  Topeka.................  28-19-50...............  Sept. 5, 1974.
    Do...............................  Hutchinson.............  28-19-50...............  Aug. 15, 1974.
Western Iron & Foundry, cupola.......  Wichita................  28-19-20A, 28-19-50A...  Oct. 4, 1974.
Kansas Army Ammunition Plant, open     Parsons................  28-19-45...............  Jan. 24, 1975.
 burning.
Reid Grain, headhouse................  Goodland...............  28-19-50...............      Do.
Sherwin-Williams Chemicals, black ash  Coffeyville............  28-19-50A..............      Do.
 kiln.
Cooperative Farm Chemicals, No. 1 NH4  Lawrence...............  28-19-20...............  Mar. 28, 1975.
 NO399-percent evaporator and
 prilling tower.
Sherwin-Williams Chemical Co., ozide   Coffeyville............  28-19-50A..............      Do.
 calciner exhaust.
Kaw Dehydrating Co., alfalfa           Lawrence...............  28-19-20...............      Do.
 dehydrator.
Empire Dist. Electric Co.: Boilers     Riverton...............  28-19-31C..............  May 23, 1975.
 Nos. 7 and 8.
Gulf Oil Chemicals Co.: Coal-fired     Pittsburg..............  28-19-31...............      Do.
 boiler.
Kansas City Power & Light: Main        La Cygne...............  28-19-31B..............      Do.
 boiler.
Mid-America Dairymen: Spray dryers     Sabetha................  28-19-20...............      Do.
 Nos. 1 and 2.
Tower Metal Products: Reverberatory    Fort Scott.............  28-19-50A..............      Do.
 furnace C.
U.S. Steel--Universal Atlas Cement...  Independence...........
  Clay storage bin...................  .......................  28-19-50A..............      Do.
  Stone storage bin..................  .......................  28-19-50A..............      Do.
Krupp Ball Mill No. 2................  .......................  28-19-50A..............      Do.
Krupp Ball Mill No. 3................  .......................  28-19-50A..............      Do.
----------------------------------------------------------------------------------------------------------------

[37 FR 19809, Sept. 22, 1972]
    Editorial Note: For Federal Register citations affecting 
Sec. 52.876, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.

[[Page 492]]



Secs. 52.877--52.880  [Reserved]



Sec. 52.881  PM10 State implementation plan development in group II areas.

    The state has submitted a committal SIP for Kansas City, Kansas. The 
committal SIP contains all the requirements identified in the July 1, 
1987, promulgation of the SIP requirements for PM10 at 52 FR 
24681, except the state will report the PM10 data which 
exceed the standard within 60 days of the exceedance, rather than 45 
days.
[55 FR 1423, Jan. 16, 1990]



Secs. 52.882--52.883  [Reserved]



Sec. 52.884  Significant deterioration of air quality.

    (a) The requirements of section 160 through 165 of the Clean Air 
Act, as amended are met; except that:
    (1) EPA retains PSD permit authority for Indian lands in the State 
of Kansas.
[49 FR 48186, Dec. 11, 1984, as amended at 54 FR 15935, Apr. 20, 1989; 
58 FR 3848, Jan. 12, 1993]



                           Subpart S--Kentucky



Sec. 52.920  Identification of plan.

    (a) Title of plan: ``Implementation Plan for the Attainment and 
Maintenance of the National and State Ambient Air Quality Standards.''
    (b) The plan was officially submitted on February 8, 1972, and was 
resubmitted on December 5, 1973.
    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) Clarifying comments on the plan submitted on March 6, 1972, by 
the Kentucky Air Pollution Control Office.
    (2) Chapters IV and V, Control Strategies, and Chapter VII, Emission 
Control Regulations, submitted on March 17, 1972, by the Kentucky Air 
Pollution Control Office.
    (3) Summary letter of Kentucky Air Pollution Control Commission and 
Regional Office meeting with attachments submitted May 3, 1972, by the 
Kentucky Air Pollution Control Office.
    (4) Letter requesting delegation of authority and offering 
justification for a two-year extension for attainment of the sulfur 
dioxide primary standard submitted on June 7, 1972, by the Governor.
    (5) Indirect source Regulation AP-11 and compliance schedules 
submitted on December 5, 1973, by the Governor.
    (6) Compliance schedules submitted on February 15, 1974, by the 
Kentucky Department for Natural Resources and Environmental Protection.
    (7) Compliance schedules submitted on April 23, 1974, by the 
Kentucky Department for Natural Resources and Environmental Protection.
    (8) Clarifying comments submitted on May 21, 1974, by the Kentucky 
Department for Natural Resources and Environmental Protection.
    (9) AQMA material submitted on January 6, 1975, by the Kentucky 
Department for Natural Resources and Environmental Protection.
    (10) Revised body of air pollution control regulations and revised 
control strategies submitted respectively on August 29 and September 16, 
1975, by the Kentucky Department for Natural Resources and Environmental 
Protection.
    (11) Letters requesting delegation of Federal authority for the 
administrative and technical portions of the Prevention of Significant 
Deterioration program were submitted on May 5 and June 13, 1976 by the 
Secretary of the Department for Natural Resources and Environmental 
protection.
    (12) 1979 revisions for Part D requirements for ozone nonattainment 
areas, submitted on June 29, 1979, by the Kentucky Department for 
Natural Resources and Environmental Protection.
    (13) 1979 revisions for Part D requirements for sulfur dioxide 
nonattainment areas (Boyd, Jefferson, McCracken, Muhlenberg, and Webster 
Counties), submitted on June 29, 1979, by the Kentucky Department for 
Natural Resources and Environmental Protection.
    (14) 1979 revisions for Part D requirements for total suspended 
particulate nonattainment areas (Bell, Boyd, Jefferson, McCracken and 
Muhlenberg counties, that portion of Bullit County in Shepherdsville, 
that portion of Campbell County in Newport, that portion of Daviess 
County in Owensboro, those portions of Henderson County in and around 
Henderson, that portion of

[[Page 493]]

Lawrence County in Louisa, that portion of Madison County in Richmond, 
that portion of Perry County in Hazard, that portion of Pike County in 
Pikeville, and that portion of Whitley County in Corbin) submitted on 
June 29, 1979, by the Kentucky Department for Natural Resources and 
Environmental Protection.
    (15) Revision to the State Implementation Plan for a bubble action 
at the Kentucky Utilities--Green River Station was submitted on December 
1, 1980.
    (16) Corrections in 1979 ozone revisions required by conditional 
approval of January 25, 1980, submitted on May 18, 1980 (letter on oil-
water effluent separators), September 22, 1980 (Jefferson County I/M 
ordinance and schedule), November 19, 1980 (Jefferson County 
transportation related commitments), and on January 8, 1981 (changes in 
Jefferson County I/M schedule), by the Kentucky Department for Natural 
Resources and Environmental Protection.
    (17) 1979 Revisions for Part D requirements for the Jefferson County 
carbon monoxide nonattainment area, submitted on June 29, 1979, by the 
Kentucky Department for Natural Resources and Environmental Protection. 
Additional materials to correct the deficiencies noted in the November 
15, 1979 proposed conditional approval were submitted as SIP revisions 
on September 22, 1980, November 19, 1980, and January 8, 1981, as noted 
in the preceding paragraph.
    (18) Air quality surveillance plan submitted on November 15, 1979, 
by the Kentucky Department for Natural Resources and Environmental 
Protection.
    (19) Revision to the State Implementation Plan for a bubble action 
at Corning Glassworks, Danville, Kentucky was submitted on May 18, 1981, 
by the Kentucky Department for Natural Resources and Environmental 
Protection.
    (20) Revision to the State Implementation Plan for a bubble action 
at National Distillers Company's Old Crow Plant in Woodford County, 
submitted on December 24, 1980, by the Kentucky Department for Natural 
Resources and Environmental Protection.
    (21) Boone County Inspection/Maintenance ordinance and 
transportation control measures for Boone, Campbell, and Kenton 
Counties, submitted on November 19, 1980, by the Kentucky Department for 
Natural Resources and Environmental Protection.
    (22) Set II VOC regulations, submitted on February 5, 1981, and 
September 24, 1982, by the Kentucky Department for Environmental 
Protection.
    (23) Implementation plan for lead, submitted on May 7, 1980, by the 
Kentucky Department for Natural Resources and Environmental Protection.
    (24) Provision for permit and exemption fees, submitted on June 10, 
1981, by the Kentucky Department for Natural Resources and Environmental 
Protection.
    (25) Provisions for public notifications and participation pursuant 
to section 127(a) of the Clean Air Act, submitted on April 8, 1980, by 
the Kentucky Department for Natural Resources and Environmental 
Protection.
    (26) Revision to the State Implementation Plan for a bubble action 
at General Electric, Louisville, Kentucky, submitted on August 7, 1981, 
by the Kentucky Department for Natural Resources and Environmental 
Protection.
    (27) Revised Boone County Inspection/Maintenance schedule submitted 
on October 9, 1981 by the Kentucky Department for Natural Resources and 
Environmental Protection.
    (28) Addition to Appendix N of Jefferson County Regulation 6.28, 
Standard of Performance for Existing Hot Air Aluminium Atomization 
Processes, submitted on May 18, 1981, by the Kentucky Department for 
Natural Resources and Environmental Protection.
    (29) Revision of Appendix N, Jefferson County Regulation 6.35, 
Standard of Performance for Existing Fabric, Vinyl and Paper Surface 
Coating Operations, submitted on November 17, 1981, by the Kentucky 
Department for Natural Resources and Environmental Protection.
    (30) Jefferson County Set II VOC regulations for new/existing 
affected facilities, submitted on October 20, 1981, by the Kentucky 
Department for Natural Resources and Environmental Protection.
    (31) Miscellaneous non-Part D revisions, submitted on June 29, 1979, 
by the Kentucky Department for Natural

[[Page 494]]

Resources and Environmental Protection.
    (32) Revision to the State Implementation Plan for a bubble action 
at Borden Chemical Co., Jefferson County, Kentucky, received by EPA from 
the Kentucky Department for Natural Resources and Environmental 
Protection on March 5, 1982.
    (33) Addition of Kentucky Regulation 401 KAR 61:165, section 5, 
Particulate Standard for Existing Primary Aluminum Reduction Plants, 
submitted on March 4, 1982, by the Kentucky Department for Natural 
Resources and Environmental Protection.
    (34) [Reserved]
    (35) Corrections in 1979 Part D revisions for sulfur dioxide 
nonattainment area (Boyd County), submitted on September 24, 1982, by 
the Kentucky Natural Resources and Environmental Protection Cabinet.
    (36) Variance for seven per- chloroethylene dry cleaners, submitted 
on August 4, 1982, by the Kentucky Department for Environmental 
Protection.
    (37) Variances for two dry cleaners, submitted on January 27, 1983, 
by the Kentucky Department for Environmental Protection.
    (38) Revised SO2 limit for large coal-fired boilers in 
Pulaski County, submitted on June 29, 1979, by the Kentucky Department 
for Natural Resources and Environmental Protection.
    (39)--(40) [Reserved]
    (41) Revisions to Appendix N, submitted July 19, 1982 and March 21, 
1983, by the Kentucky Department for Environmental Protection.
    (42) Regulation 401 KAR 61:070, Existing Ferroally Production 
Facilities, for the Marshall County Part D TSP area, submitted on June 
29, 1979, by the Kentucky Department for Environmental Protection.
    (43) 1982 revisions to the Part D plan for the Jefferson County 
ozone and carbon monoxide nonattainment area, submitted by the Kentucky 
Natural Resources and Environmental Protection Cabinet on February 9, 
June 15, September 12, November 21, and December 9, 1983.
    (44) Variances for two dry cleaners, Jiffy The Cleaners and Hiland 
Cleaners, submitted on April 25, 1984, by the Kentucky Natural Resources 
Environmental Protection Cabinet.
    (45) Corrections in the Part D TSP SIP and other revisions submitted 
on December 9, 1982, and May 1, 1984, by the Kentucky Department for 
Environmental Protection.
    (i) Incorporation by reference.
    (A) Revisions in regulations 401 KAR--

    50:010, Definitions and Abbreviations;
    50:055, General Compliance Requirements;
    61:005, General Provisions;
    61:015, Existing Indirect Heat Exchangers;
    61:075, Steel Plants and Foundries Using Existing Electric Arc 
Furnaces;
    61:080, Steel Plants Using Existing Basic Oxygen Process Furnaces;
    61:140, Existing By-Product Coke Manufacturing Plants; and
    61:170, Existing Blast Furnace Casthouses.


The changes in these regulations were effective September 22, 1982 
(50:055), December 1, 1982 (50:010, 61:005, 61:015, 61:075, and 61:140), 
and April 1, 1984 (61:080 and 61:170). No action is taken on the 
definition of ``volatile organic compounds''in 401 KAR 50:010.
    (ii) Other material--none.
    (46) Kentucky regulation 401 KAR 51:017, Prevention of significant 
deterioration of air quality, and Kentucky's State Implementation Plan 
Revision for the Protection of Visibility for the Commonwealth of 
Kentucky pursuant to 40 CFR part 51, subpart P, submitted on February 
20, 1986, by the Kentucky Natural Resources and Environmental Protection 
Cabinet.
    (i) Incorporation by reference. (A) Kentucky regulation 401 KAR 
51:017, Prevention of significant deterioration of air quality, which 
became State-effective on February 4, 1986.
    (ii) Other material. (A) Kentucky's State Implementation Revision 
for the Protection of Visibility for the Commonwealth of Kentucky, 
pursuant to 40 CFR part 51, subpart P, which became State-effective on 
February 4, 1986.
    (47) Stack height regulations were submitted to EPA on July 15, 
1986, by the Kentucky Natural Resources and Environmental Protection 
Cabinet.
    (i) Incorporation by reference.
    (A) Regulation 401 KAR 50:042, which became effective on June 10, 
1986.
    (ii) Other material--none.

[[Page 495]]

    (48) Revisions to the I/M portions of the carbon monoxide and ozone 
Part D plans for Jefferson County, submitted by the Kentucky Natural 
Resources and Environmental Protection Cabinet on February 18, 1986.
    (i) Incorporation by reference.
    (A) A revised Regulation 8, Vehicle Exhaust Testing Requirements of 
the rules of the Air Pollution Control District of Jefferson County 
which was adopted on September 18, 1985.
    (ii) Other materials--none.
    (49) A revision to the Kentucky SIP for Tennessee Valley Authority 
Paradise Steam Plant pursuant to the procedures specified in Kentucky 
regulation 401 KAR 61:015, section 3 was submitted on June 29, 1987, by 
the Kentucky Natural Resources and Environmental Protection Cabinet. The 
revised SO2 limits are contained in Permit Number 0-87-012, 
issued on June 29, 1987.
    (i) Incorporation by reference.
    (A) Permit Number 0-87-012, issued by the Kentucky Natural Resources 
and Protection Cabinet on June 29, 1987.
    (ii) Other material.
    (A) Letter of June 27, 1987 from the Kentucky Natural Resources and 
Environmental Protection Cabinet.
    (50) A revision in Kentucky regulation 401 KAR 61:140, Existing by-
product coke manufacturing plants, submitted on September 19, 1986, by 
the Kentucky Natural Resources and Environmental Protection Cabinet.
    (i) Incorporation by reference.
    (A) A revision to Division of Air Pollution regulation 401 Kentucky 
Administrative Regulations (KAR) 61:140, Existing by-product coke 
manufacturing plants, which became effective on September 4, 1986.
    (B) Letter of September 19, 1986 from the Commonwealth of Kentucky 
to EPA.
    (51) Revisions to the I/M portions of the carbon monoxide and ozone 
Part D plans for Jefferson County, submitted by the Kentucky Natural 
Resources and Environmental Protection Cabinet on March 20, 1987.
    (i) Incorporation by reference.
    (A) A revised Regulation 8, Vehicle Exhaust Testing Requirements; of 
the rules of the Air Pollution Control District of Jefferson County 
which was adopted on December 17, 1986.
    (B) March 2, 1987 letter to EPA from Jefferson County.
    (ii) Additional materials--none.
    (52) Kentucky Plan for the ``Protection of Visibility in Class I 
Areas (PART II)'' submitted to EPA on August 31, 1987, by the Kentucky 
Department for Environmental Protection (KDEP) to satisfy the Part 2 
visibility requirements.
    (i) Incorporation by reference.
    (A) June 8, 1988, letter from the Kentucky Natural Resources and 
Environmental Protection Cabinet, October 9, 1987, clarification letter 
from the Kentucky Natural Resources and Environmental Protection 
Cabinet, and page 8 of the Kentucky plan for the protection of 
visibility in Class I areas (PART II) containing the periodic review 
requirements satisfying 40 CFR 51.306(c), adopted on August 31, 1987.
    (ii) Additional material.
    (A) Narrative entitled ``The Kentucky Plan for the Protection of 
Visibility in Class I Areas (PART II).''
    (53) Revisions to Kentucky regulation 401 KAR 50:015, Documents 
incorporated by reference, submitted by the Kentucky Natural Resources 
and Environmental Protection Cabinet on March 23, 1987.
    (i) Incorporation by reference.
    (A) Revisions to Kentucky regulation 401 KAR 50:015, Documents 
incorporated by reference which became State-effective on February 10, 
1987.
    (B) Letter of March 23, 1987, from the Kentucky Natural Resources 
and Environmental Protection Cabinet transmitting the foregoing 
revisions.
    (ii) Additional material--none.
    (54) An opacity variance for boiler Units 1 and 2 of Tennessee 
Valley Authority's (TVA's) Paradise Steam Plant, submitted on August 6, 
1986, by the Kentucky Natural Resources and Environmental Protection 
Cabinet.
    (i) Incorporation by reference.
    (A) Permit No. 0-86-75, for the TVA Paradise Steam Plant, issued by 
the Kentucky Natural Resources and Environmental Protection Cabinet on 
July 24, 1986.
    (B) Letter of August 6, 1986, from the Kentucky Natural Resources 
and Environmental Protection Cabinet.

[[Page 496]]

    (ii) Other material--none.
    (55) Revisions to Jefferson County, Kentucky Regulation 2.08, Permit 
Fees and Renewal, submitted on March 20, 1987, by the Kentucky Natural 
Resources and Environmental Protection Cabinet.
    (i) Incorporation by reference.
    (A) Revisions to Jefferson County, Kentucky Regulation 2.08, Permit 
Fees and Renewal, which became State-effective on December 17, 1986.
    (B) Letter of March 20, 1987, from the Kentucky Natural Resources 
and Environmental Protection Cabinet.
    (ii) Other material--none.
    (56) A revision to Kentucky Regulation 401 KAR 51:017, Prevention of 
Significant Deterioration of Air Quality, submitted on February 9, 1988, 
by the Kentucky Natural Resources and Environmental Protection Cabinet. 
The revision to section 12(1)(e) replaces the reference to Regulation 
401 KAR 51:052 with a reference to 40 CFR part 51, Appendix S, section 
IV. This revision became State-effective on December 11, 1987.
    (i) Incorporation by reference.
    (A) Kentucky Regulation 401 KAR 51:017, Prevention of Significant 
Deterioration of Air Quality, section 12(1)(e), which became State-
effective on December 11, 1987.
    (ii) Other material.
    (A) Letter of February 9, 1988, from the Kentucky Natural Resources 
and Environmental Protection Cabinet.
    (57) Jefferson County Air Pollution Control District Regulation 6.38 
was submitted to EPA on March 20, 1987 by the Kentucky Natural Resources 
and Environmental Protection Cabinet.
    (i) Incorporation by reference.
    (A) Jefferson County Air Pollution Control District Regulation 6.38, 
``Standards of performance for existing air oxidation processes in the 
synthetic organic chemical manufacturing industry'', which became 
effective December 17, 1986.
    (B) Letter of March 20, 1987, from the Kentucky Natural Resources 
and Environmental Protection Cabinet.
    (ii) Other materials--none.
    (58) Jefferson County Air Pollution Control District Regulation 6.39 
was submitted to EPA on March 20, 1987, by the Kentucky Natural 
Resources and Environmental Protection Cabinet.
    (i) Incorporation by reference.
    (A) Jefferson County Air Pollution Control District Regulation 6.39, 
``Standard of performance for equipment leaks of volatile organic 
compounds in existing synthetic organic chemical and polymer 
manufacturing plants'', which became effective December 17, 1986.
    (B) March 20, 1987, letter from the Kentucky Natural Resources and 
Environmental Protection Cabinet.
    (ii) Other materials--none.
    (59) Revision to Jefferson County Regulations 3.05, Methods of 
Measurement submitted on January 19, 1989, by the Kentucky Natural 
Resources and Environmental Protection Cabinet.
    (i) Incorporation by reference.
    (A) Revisions to the Jefferson County Regulations, 3.05. Methods of 
Measurement.
    This revision became State-effective April 20, 1988.
    (ii) Other material.
    (A) Letter of January 19, 1989, from the Kentucky Natural Resources 
and Environmental Protection Cabinet.
    (60) Corrections in Part D TSP SIP and other revisions submitted on 
September 19, 1986, by the Kentucky Department for Environmental 
Protection. The removal of these last two conditions renders the 
Kentucky's Part D SIP for TSP fully approved.
    (i) Incorporation by reference.
    (A) Revisions in Regulation 401 KAR--

    50:015. Documents Incorporated by Reference.
Section 1. Code of Federal Regulations,
Section 3. American Society for Testing and Materials,
Section 8. Kentucky Division of Air Pollution,
Section 10. American Public Health Association, and
Section 11. Availability.
    59:010. New process operations.
Section 1. Applicability,
Section 2. Definitions,
Section 3. Standard for Particulate Matter, and
Section 4. Test Methods and Procedures.
    61:020. Existing process operations.
Section 1. Applicability

[[Page 497]]

Section 2. Definitions;
Section 3. Standard for Particulate Matter, and
Section 4. Test Methods and Procedures.

    These changes were effective September 4, 1986.
    (B) Letter of September 19, 1986, from the Kentucky Natural 
Resources and Environmental Protection Cabinet to EPA.
    (ii) Other material--none.
    (61) Revisions in Regulations 5.01, 6.12, 6.19, 6.22, 6.29, 6.30, 
6.31, 6.32, 6.33, 6.34, and 6.35 of the Jefferson County portion of 
Kentucky's SIP were submitted on January 19, 1989, by Kentucky's Natural 
Resources Division and Environmental Protection Cabinet.
    (i) Incorporation by reference.
    (A) Amendments to the Jefferson County Regulations 5.01, 6.12, 6.19, 
6.22, 6.29, 6.30, 6.31, 6.32, 6.33, 6.34, and 6.35 adopted on April 20, 
1988.
    (B) Letter of January 19, 1989, from Kentucky's Natural Resources 
and Environmental Protection Cabinet.
    (ii) Other materials-none.
    (62) Revision to Kentucky Regulation 401 KAR 50:015, Documents 
incorporated by reference submitted on February 9, 1989, by the Kentucky 
Natural Resources and Environmental Protection Cabinet. Section 5(1)(a) 
was amended to incorporate by reference Supplement A to the Guideline on 
Air Quality Models (Revised), July 1987. Supplement A became effective 
February 5, 1988. Section 12(4) was amended to reflect the current phone 
number for the Florence Regional Office. The revisions to 50:015 became 
state effective October 26, 1988.
    (i) Incorporation by Reference.
    (A) Kentucky Regulation 401 KAR 50:015, Documents incorporated by 
reference, Section 12(4) was amended on October 26, 1988.
    (B) Supplement A to the Guideline on Air Quality Models EPA-450/2-
78-027R that became effective February 5, 1988.
    (ii) Other material.
    (A) Letter of February 9, 1989, from the Kentucky Natural Resources 
and Environmental Protection Cabinet.
    (63) Revisions to Kentucky Regulations 401 KAR 50:010, Definitions 
and abbreviations and 401 KAR 51:017, Prevention of Significant 
Deterioration of Air Quality, submitted on December 29, 1986, by the 
Kentucky Natural Resources and Environmental Protection Cabinet.
    (i) Incorporation by reference. (A) Revisions in Kentucky 
Regulations are as follows. 401 KAR 50:010, Definitions and 
abbreviations section 1(49), and 401 KAR 51:017 Prevention of 
Significant Deterioration of Air Quality, Section 8(3). These revisions 
were state effective December 2, 1986.
    (ii) Other material. (A) Letter of February 9, 1988, from the 
Kentucky Natural Resources and Environmental Protection Cabinet.
    (64) Revisions to Jefferson County Regulation 4, Emergency Episode 
submitted on January 19, 1989 and July 12, 1989, by the Kentucky Natural 
Resources and Environmental Protection Cabinet.
    (i) Incorporation by reference.
    (A) Revisions to the following Jefferson County Regulation.
    (1) Regulation 4, except Regulation 4.02, effective February 16, 
1983.
    (2) Regulation 4.02 Episode Criteria effective April 20, 1988.
    (ii) Other material.
    (A) Letters of January 19, 1989 and July 12, 1989, from the Kentucky 
Natural Resources and Environmental Protection Cabinet.
    (65) Addition of Jefferson County Regulation 2.05, Prevention of 
Significant Deterioration of Air Quality, submitted on August 2, 1989, 
by the Kentucky Natural Resources and Environmental Protection Cabinet.
    (i) Incorporation by reference.
    (A) Jefferson County Regulation 2.05, Prevention of Significant 
Deterioration of Air Quality. This regulation became effective April 19, 
1989.
    (ii) Other material.
    (A) August 2, 1989, letter from the Natural Resources and 
Environmental Protection Cabinet.
    (66) On July 7, 1988, revisions to Kentucky's State Implementation 
Plan for PM10 were submitted by the Kentucky Natural 
Resources and Environmental Protection Cabinet. The submittal included a 
committal SIP. EPA is taking no action on 401 KAR 51:052, Review of new 
sources in or impacting upon non-attainment areas.
    (i) Incorporation by reference.

[[Page 498]]

    (A) The following revisions to 401 KAR were effective April 14, 
1988:
    (1) 50:010. Definitions and abbreviations: Section 1. Definitions 
and section 2. Abbreviations.
    (2) 50:015. Documents incorporated by reference: Sections 1, 3, and 
11.
    (3) 50:035. Permits.
    (4) 51:010. Attainment status designations: Section 1(1) and 
Appendices A and B.
    (5) 51:017. Prevention of significant deterioration of air quality: 
Section 8(4) (e) and (f), section 8(9), section 12(1) (f) and (g), and 
Appendices A, B, C, and D.
    (6) 53:005. General provisions: Section 3(2).
    (7) 53:010. Ambient air quality standards: Appendix A.
    (8) 55:005. Significant harm criteria.
    (9) 55:010. Episode criteria: Headings and Appendix A.
    (10) 59:010. New process operations: Section 3(1) (b) and (c).
    (11) 61:020. Existing process operations: Section 3(1)(b).
    (12) 61:170. Existing blast furnace casthouses: Necessity and 
function paragraph and section 2(3).
    (ii) Other material.
    (A) Letter of December 7, 1987, from the Kentucky Natural Resources 
and Environmental Protection Cabinet.
    (B) Letter of July 7, 1988, from the Kentucky Natural Resources and 
Environmental Protection Cabinet.
    (C) Letter of January 23, 1989, from the Kentucky Natural Resources 
and Environmental Protection Cabinet.
    (67) Operating permits for nine presses at the Alcan Foil Products 
facility located in Louisville were submitted to EPA on July 28, 1989 by 
the Commonwealth of Kentucky.
    (i) Incorporation by reference. (A) Alcan Foil Products operating 
permit numbers 103-74, 104-74, 105-74, 106-74, 110-74, and 111-74 which 
became State-effective on February 28, 1990.
    (ii) Other material.
    (A) Letter of July 28, 1989, from the Commonwealth of Kentucky 
Natural Resources and Environmental Protection Cabinet.
    (68) Revisions to the Commonwealth of Kentucky State Implementation 
Plan (SIP) concerning Jefferson County Volatile Organic Compounds were 
submitted on February 12, 1992 by the Kentucky Natural Resources and 
Environmental Protection Cabinet.
    (i) Incorporation by reference.
    (A) Revisions to the following Jefferson County Regulations were 
effective May 15, 1991.
    (1) Regulation 1.02 Definitions: (45), (61), (62), and (91).
    (2) Regulation 1.08 Administrative Procedures: Subsections 1.1.1, 
1.1.3, 2.2.7, 2.3, and 2.5, Section 3.0 closing paragraph, and 
Subsections 4.6, 8.1 and 8.4.
    (3) Regulation 6.12 Standard of Performance for Existing Asphalt 
Paving Operations: Sections 1.0 and 5.0.
    (4) Regulation 6.13 Standard of Performance for Existing Storage 
Vessels for Volatile Organic Compounds.
    (5) Regulation 6.16 Standard of Performance for Existing Large 
Appliance Surface Coating Operations.
    (6) Regulation 6.18 Standards of Performance for Existing Solvent 
Metal Cleaning Equipment.
    (7) Regulation 6.19 Standard of Performance for Existing Metal 
Furniture Surface Coating Operations.
    (8) Regulation 6.23 Standard of Performance for Existing Dry 
Cleaning Facilities: Section 1.0 and Subsection 4.3.
    (9) Regulation 6.29 Standard of Performance for Existing Graphic 
Arts Facilities Using Rotogravure and Flexography.
    (10) Regulation 6.30 Standard of Performance for Existing Factory 
Surface Coating Operations of Flat Wood Paneling.
    (11) Regulation 6.31 Standard of Performance for Existing 
Miscellaneous Metal Parts and Products Surface Coating Operations.
    (12) Regulation 6.32 Standard of Performance for Leaks from Existing 
Petroleum Refinery Equipment.
    (13) Regulation 6.33 Standard of Performance for Existing 
Synthesized Pharmaceutical Product Manufacturing Operations.
    (14) Regulation 6.34 Standard of Performance for Existing Pneumatic 
Rubber Tire Manufacturing Plants.
    (15) Regulation 6.35 Standard of Performance for Existing Fabric, 
Vinyl and Paper Surface Coating Operations.

[[Page 499]]

    (16) Regulation 7.11 Standard of Performance for New Asphalt Paving 
Operations: Sections 1.0, 6.0, and 7.0.
    (17) Regulation 7.12 Standard of Performance for New Storage Vessels 
for Volatile Organic Compounds: Section 1.0, Subsections 2.10, 5.3.2, 
5.3.3, and 5.4, and Section 8.0.
    (18) Regulation 7.16 Standard of Performance for New Large Appliance 
Surface Coating Operations: Section 1.0, Subsections 2.3, 4.2, 4.4, 5.3 
and 5.4, and Sections 6.0 and 7.0.
    (19) Regulation 7.18 Standards of Performance for New Solvent Metal 
Cleaning Equipment: Section 1.0 and Subsection 2.4.
    (20) Regulation 7.19 Standard of Performance for New Metal Furniture 
Surface Coating Operations: Section 1.0, Subsections 2.3, 4.3, 4.5.1, 
5.2, and Sections 6.0 and 7.0.
    (21) Regulation 7.23 Standard of Performance for New 
Perchloroethylene Dry Cleaning Facilities: Section 1.0 and Subsection 
4.5.
    (22) Regulation 7.52 Standard of Performance for New Fabric, Vinyl, 
and Paper Surface Coating Operations: Section 1.0, Subsections 2.3, 
2.12, 4.1, 4.3, 4.5.1, and 5.3, and Section 6.0.
    (23) Regulation 7.56 Standard of Performance for Leaks from New 
Petroleum Refinery Equipment: Subsection 2.4 and 2.6, and Section 7.0.
    (24) Regulation 7.57 Standard of Performance for New Graphic Arts 
Facilities Using Rotogravure and Flexography: Section 1.0, Subsections 
2.8, 4.2, 4.4.1, and 5.2, and Sections 6.0, 7.0, and 8.0.
    (25) Regulation 7.58 Standard of Performance for New Factory Surface 
Coating Operations of Flat Wood Paneling: Section 1.0, Subsection 2.5, 
4.4.1, and 5.4, and Section 6.0.
    (26) Regulation 7.59 Standard of Performance for New Miscellaneous 
Metal Parts and Products Surface Coating Operations: Section 1.0, 
Subsections 2.2, 2.4, 2.5, 2.8.7, 4.3, 4.5.1, 5.1.1, 5.1.2, 5.1.4, 5.2, 
and 5.4, and Sections 6.0 and 7.0.
    (27) Regulation 7.60 Standard of Performance for New Synthesized 
Pharmaceutical Product Manufacturing Operations: Section 1.0 and Section 
2.0.
    (28) Regulation 7.61 Standard of Performance for New Pneumatic 
Rubber Tire Manufacturing Plants: Section 1.0, Subsections 2.2, 2.3, 
2.4, 2.5, 2.6, and 2.7, and Section 3.0.
    (ii) Other material.
    (A) Letter dated February 12, 1992, from the Commonwealth of 
Kentucky Natural Resources and Environmental Protection Cabinet.
    (69) Revisions to the Commonwealth of Kentucky State Implementation 
Plan (SIP) concerning the Commonwealth and Jefferson County, Kentucky 
for Volatile Organic Compounds were submitted on October 20, 1992, 
February 17, 1993, and March 4, 1993, by the Kentucky Natural Resources 
and Environmental Protection Cabinet.
    (i) Incorporation by reference.
    (A) Revisions to the following Jefferson County Regulations were 
effective November 18, 1992.
    (1) Regulation 1.05. Compliance with Emission Standards and 
Maintenance Requirements.
    (2) Regulation 1.06. Source Self-Monitoring and Reporting.
    (3) Regulation 6.17. Standard of Performance for Existing Automobile 
and Truck Surface Coating Operations.
    (4) Regulation 6.36. Standard of Performance for Existing Metal 
Parts and Products Surface Coating Operations at Heavy Duty Truck 
Manufacturing Plants.
    (B) Revisions to the following Commonwealth of Kentucky Regulations 
were effective June 24, 1992.
    (1) Regulation 401 KAR 50:010. Definitions and abbreviations of 
terms used in Title 401, Chapters 50, 51, 53, 55, 57, 59, 61, 63, and 
65.
    (2) Regulation 401 KAR 50:012. General application.
    (3) Regulation 401 KAR 50:047. Test procedures for capture 
efficiency.
    (4) Regulation 401 KAR 51:001. Definitions and abbreviations of 
terms used in Title 401, Chapter 51.
    (5) Regulation 401 KAR 59:001. Definitions and abbreviations of 
terms used in Title 401, Chapter 59.
    (6) Regulation 401 KAR 59:185. New solvent metal cleaning equipment.
    (7) Regulation 401 KAR 59:190. New insulation of magnet wire 
operations.
    (8) Regulation 401 KAR 59:210. New fabric, vinyl and paper surface 
coating operations.

[[Page 500]]

    (9) Regulation 401 KAR 59:212. New graphic arts facilities using 
rotogravure and flexography.
    (10) Regulation 401 KAR 59:214. New factory surface coating 
operations of flat wood paneling.
    (11) Regulation 401 KAR 59:225. New miscellaneous metal parts and 
products surface coating operations.
    (12) Regulation 401 KAR 59:230. New synthesized pharmaceutical 
product manufacturing operations.
    (13) Regulation 401 KAR 59:240. New perchloroethylene dry cleaning 
systems.
    (14) Regulation 401 KAR 61:001. Definitions and abbreviations of 
terms used in Title 401, Chapter 61.
    (15) Regulation 401 KAR 61:050. Existing storage vessels for 
petroleum liquids.
    (16) Regulation 401 KAR 61:090. Existing automobile and light-duty 
truck surface coating operations.
    (17) Regulation 401 KAR 61:095. Existing solvent metal cleaning 
equipment.
    (18) Regulation 401 KAR 61:100. Existing insulation of magnet wire 
operations.
    (19) Regulation 401 KAR 61:105. Existing metal furniture surface 
coating operations.
    (20) Regulation 401 KAR 61:110. Existing large appliance surface 
coating operations.
    (21) Regulation 401 KAR 61:120. Existing fabric, vinyl and paper 
surface coating operations.
    (22) Regulation 401 KAR 61:124. Existing factory surface coating 
operations of flat wood paneling.
    (23) Regulation 401 KAR 61:125. Existing can surface coating 
operations.
    (24) Regulation 401 KAR 61:130. Existing coil surface coating 
operations.
    (25) Regulation 401 KAR 61:132. Existing miscellaneous metal parts 
and products surface coating operations.
    (26) Regulation 401 KAR 61:137. Leaks from existing petroleum 
refinery equipment.
    (27) Regulation 401 KAR 61:150. Existing synthesized pharmaceutical 
product manufacturing operations.
    (28) Regulation 401 KAR 61:155. Existing pneumatic rubber tire 
manufacturing plants.
    (29) Regulation 401 KAR 61:160. Existing perchloroethylene dry 
cleaning systems.
    (30) Regulation 401 KAR 61:175. Leaks from existing synthetic 
organic chemical and polymer manufacturing equipment.
    (31) Regulation 401 KAR 63:001. Definitions and abbreviations of 
terms used in Title 401, Chapter 63.
    (32) Regulation 401 KAR 63:025. Asphalt paving operations.
    (C) Kentucky Regulation 401 KAR 59:315, Specific New Sources, 
effective June 24, 1992.
    (D) Revisions to following Kentucky Regulations were effective 
February 8, 1993.
    (1) Regulation 401 KAR 51:010. Attainment Status Designations.
    (2) Regulation 401 KAR 59:175. New service stations.
    (3) Regulation 401 KAR 61:085. Existing service stations.
    (4) Regulation 401 KAR 63:031. Leaks from Gasoline Tanks.
    (ii) Other material. None.
    (70) The maintenance plan for the Owensboro and Edmonson County 
Areas which include Daviess, a portion of Hancock, and Edmonson Counties 
submitted by the Commonwealth of Kentucky Natural Resources and 
Environmental Protection Cabinet on November 13, 1992, November 24, 
1992, March 10, 1993, July 16, 1993, March 3, 1994, and August 29, 1994, 
as part of the Kentucky SIP. The 1990 Baseline Emission Inventory for 
the Owensboro and Edmonson County areas which include Daviess, a portion 
of Hancock, and Edmonson Counties.
    (i) Incorporation by reference.
    (A) Commonwealth of Kentucky Attainment Demonstration and Ten Year 
Maintenance Plan for All Areas Designated Marginal Nonattainment for 
Ozone. The effective date is December 28, 1992.
    (B) Attachment A--Demonstration of Permanent and Enforceable 
Reductions and Calculations of Interim Year Emission Projections. The 
effective date is August 26, 1994.
    (C) Attachment B--VOC Emissions Summary for Kentucky's Marginal 
Ozone Nonattainment Areas. The effective date is August 26, 1994.

[[Page 501]]

    (D) Attachment C--CO Emissions Summary for Kentucky's Marginal Ozone 
Nonattainment Areas. The effective date is August 26, 1994.
    (E) Attachment D--NOX Emissions Summary for Kentucky's 
Marginal Ozone Nonattainment Areas. The effective date is August 26, 
1994.
    (F) Table 6-12 Biogenic Emissions Hancock County, Kentucky. The 
effective date is December 28, 1992.
    (G) Table 6-11 Biogenic Emissions Daviess County, Kentucky. The 
effective date is December 28, 1992.
    (H) Table 6-1. Biogenic Emissions Edmonson County, Kentucky. The 
effective date is December 28, 1992.
    (ii) Other material.
    (A) February 28, 1994, letter from John E. Hornback, Director, 
Division for Air Quality to Mr. Doug Neeley, Chief, Air Programs Branch.
    (B) October 4, 1994, letter from Phillip J. Shepherd, Secretary, 
Natural Resources and Environmental Protection Cabinet to John H. 
Hankinson, Regional Administrator, USEPA Region IV.
    (71) The Commonwealth of Kentucky, Natural Resources and 
Environmental Protection Cabinet submitted revisions to the Kentucky 
State Implementation Plan on January 15, 1993 These revisions address 
the requirements of section 507 of title V of the CAA and establish the 
Small Business Stationary Source Technical and Environmental Assistance 
Program (PROGRAM).
    (i) Incorporation by reference.
    (A) Revision to the Kentucky State Implementation Plan to 
incorporate document titled ``Kentucky Small Business Stationary Source 
Technical Environmental Assistance Program'' which was approved by the 
Kentucky Natural Resources and Environmental Protection Cabinet 
effective on July 15, 1993.
    (ii) Additional Material. None.
    (72) Modifications to the existing basic I/M program in Jefferson 
County to implement an anti-tampering check, pressure testing of the 
evaporative control system, and testing of commuter vehicles submitted 
by the Commonwealth of Kentucky on November 12, 1993.
    (i) Incorporation by reference. Regulation 8.01 and 8.02, adopted on 
February 17, 1993, and Regulation 8.03 adopted on February 17, 1993.
    (ii) Other material. None.
    (73) The maintenance plan for the Paducah area which include 
Livingston and Marshall Counties submitted by the Commonwealth of 
Kentucky Natural Resources and Environmental Protection Cabinet on 
November 13, 1992, November 24, 1992, March 10, 1993, July 16, 1993, 
March 3, 1994, and August 29, 1994, as part of the Kentucky SIP. The 
1990 Baseline Emission Inventory for the Paducah area which include 
Livingston and Marshall Counties.
    (i) Incorporation by reference.
    (A) Commonwealth of Kentucky Attainment Demonstration and Ten Year 
Maintenance Plan for all areas designated Marginal Nonattainment for 
Ozone. The effective date is January 15, 1993.
    (B) Table 6-13 Biogenic Emissions, Livingston County, Kentucky. The 
effective date is January 15, 1993.
    (C) Table 6-14 Biogenic Emissions, Marshall County, Kentucky. The 
effective date is January 15, 1993.
    (ii) Other material.
    (A) January 15, 1993, letter from Phillip J. Shepherd, Secretary, 
Natural Resources and Environmental Protection Cabinet to Patrick Tobin, 
Acting Regional Administrator, U.S. EPA Region IV.
    (B) February 28, 1994, letter from John E. Hornback, Director, 
Division for Air Quality to Mr. Doug Neeley, Chief, Air Programs Branch.
    (C) October 4, 1994, letter from Phillip J. Shepherd, Secretary, 
Natural Resources and Environmental Protection Cabinet to John H. 
Hankinson, Regional Administrator, U.S. EPA Region IV.
    (74)-(75)  [Reserved]
    (76) The maintenance plan and for the Lexington area which include 
Fayette and Scott Counties submitted by the Commonwealth of Kentucky 
Natural Resources and Environmental Protection Cabinet on November 13, 
1992, November 24, 1992, March 10, 1993, July 16, 1993, March 3, 1994, 
and August 29, 1994, September 28, 1994 and June 14, 1995, as part of 
the Kentucky SIP. The 1990 Baseline Emission Inventory for the Lexington 
area which include Fayette and Scott Counties.

[[Page 502]]

    (i) Incorporation by reference.
    (A) Commonwealth of Kentucky Attainment Demonstration and Ten Year 
Maintenance Plan for all areas designated Marginal Nonattainment for 
Ozone. The effective date is January 15, 1993.
    (B) Table 6-6 Biogenic Emissions Fayette County, Kentucky. The 
effective date is January 15, 1993.
    (C) Table 6-7 Biogenic Emissions, Scott, Kentucky. The effective 
date is January 15, 1993.
    (ii) Other material.
    (A) February 28, 1994, letter from John E. Hornback, Director, 
Division for Air Quality to Mr. Doug Neeley, Chief, Air Programs Branch.
    (B) October 4, 1994, letter from Phillip J. Shepherd, Secretary, 
Natural Resources and Environmental Protection Cabinet to John H. 
Hankinson, Regional Administrator, U.S. EPA Region 4.
    (C) January 15, 1993, letter from Phillip J. Shepherd, Secretary, 
Natural Resources and Environmental Protection Cabinet to Patrick M. 
Tobin, Acting Regional Administrator, U.S. EPA Region 4.
    (77) Revisions to the Commonwealth of Kentucky State Implementation 
Plan (SIP) concerning emission statements were submitted on December 29, 
1994, by the Kentucky Natural Resources and Environmental Protection 
Cabinet.
    (i) Incorporation by reference.
    (A) Regulation 401 KAR 50:035 Permits. Section 1, Section 2(1) and 
Section 10. Regulation became effective September 28, 1994.
    (ii) None.
    (78) Operating Permit requiring VOC RACT for Calgon Corporation in 
the Kentucky portion of the Ashland/Huntington ozone nonattainment area, 
submitted November 11, 1994.
    (i) Incorporation by reference. Natural Resources and Environmental 
Protection Cabinet; Kentucky Department for Environmental Protection; 
Division for Air Quality; Permit 0-94-020; Calgon Carbon Corporation, 
effective on November 17, 1994.
    (ii) Other material. Letter of November 23, 1994, from the 
Commonwealth of Kentucky Natural Resources and Environmental Protection 
Cabinet.
    (79) Revisions to the Commonwealth of Kentucky State Implementation 
Plan (SIP) regarding the definition of volatile organic compound (VOC) 
submitted on January 27, 1995.
    (i) Incorporation by reference.
    (A) 401 KAR 50:010. Definitions and abbreviations of terms used in 
401 KAR Chapters 50, 51, 53, 55, 57, 59, 61, 63, and 65, effective April 
6, 1995.
    (B) 401 KAR 51:001. Definitions and abbreviations of terms used in 
401 KAR Chapter 51, effective April 6, 1995.
    (C) 401 KAR 59:001. Definitions and abbreviations of terms used in 
401 KAR Chapter 59, effective April 6, 1995.
    (D) 401 KAR 61:001. Definitions and abbreviations of terms used in 
401 KAR Chapter 61, effective April 6, 1995.
    (E) 401 KAR 63:001. Definitions and abbreviations of terms used in 
401 KAR Chapter 63, effective April 6, 1995.
    (F) 401 KAR 65:001. Definitions and abbreviations of terms used in 
401 KAR Chapter 65, effective April 6, 1995.
    (ii) Other material.
    (A) May 4, 1995, letter from Phillip J. Shepherd, Secretary, Natural 
Resources and Environmental Protection Cabinet to John H. Hankinson, 
Regional Administrator, U.S. EPA, Region IV.
    (80) The maintenance plan for the Ashland-Huntington area which 
includes Boyd and a portion of Greenup Counties was submitted by the 
Commonwealth of Kentucky Natural Resources and Environmental Protection 
Cabinet on November 13 and May 24, 1995, as part of the Kentucky SIP. 
The 1990 Baseline Emission Inventory for the Ashland-Huntington area 
which includes Boyd and a portion of Greenup Counties which was 
submitted on November 13, 1992.
    (i) Incorporation by reference.
    (A) Kentucky Natural Resources and Environmental Protection Cabinet 
Request to Redesignate the Huntington/Ashland Moderate Ozone 
Nonattainment Area, Maintenance Plan, effective May 24, 1995.
    (B) Appendix F Kentucky Projected Emissions Summary: VOC, CO, and 
NOX, effective May 24, 1995.
    (C) Table 6-1 Summary of Biogenic Emissions Huntington-Ashland MSA, 
effective May 24, 1995.
    (ii) Other material.

[[Page 503]]

    (A) May 24, 1995, letter from Phillip J. Shepherd, Secretary, 
Natural Resources and Environmental Protection Cabinet to John H. 
Hankinson, Regional Administrator, USEPA Region 4.
    (81) Revisions to air permit rules submitted by the Kentucky Natural 
Resources and Environmental Protection Cabinet on December 29, 1994.
    (i) Incorporation by reference. Revised Rule 401 KAR 50:035, 
``Permits'', Sections 1 through 7, effective September 28, 1994.
    (ii) Other material. None.
    (82) Revision to the Kentucky State Implementation Plan; Regulation 
6.40 of the Air Pollution Control District of Jefferson County which was 
submitted to EPA on March 4, 1993.
    (i) Incorporation by reference.
    Regulation 6.40 Standards of Performance for Gasoline Transfer to 
Motor Vehicles (Stage II Vapor Recovery and Control) which were adopted 
on December 16, 1992.
    (ii) Other material. None.
    (83) Revisions to the Kentucky State Implementation Plan submitted 
by the Natural Resources and Environmental Protection Cabinet on June 
15, 1983.
    (i) Incorporation by reference.

    401 KAR 50:025 Classification of Counties, and 401 KAR 61:015 
Existing Indirect Heat Exchangers, effective June 1, 1983.


    (ii) Additional material. None.
    (84) Revisions to the Kentucky State Implementation Plan submitted 
by the Natural Resources and Environmental Protection Cabinet on 
December 29, 1994. The regulations being revised are 401 KAR 59:101 New 
Bulk Gasoline Plants and 401 KAR 61:056 Existing Bulk Gasoline Plants.
    (i) Incorporation by reference. Division for Air Quality regulations 
401 KAR 59:101 New bulk gasoline plants, and 401 KAR 61:056 Existing 
bulk gasoline plants, effective September 28, 1994.
    (ii) Additional material. None.
    (85) The Commonwealth of Kentucky submitted revisions to the 
Kentucky SIP on June 19, 1996. These revisions involve changes to 401 
KAR Chapters 50, 51, 59, 61, 63, and 65.
    (i) Incorporation by reference. 401 KAR Chapters 50:010(62), 
51.001(62), 59:001(63), 61:001(63), 63:001(62), and 65:001(31) of the 
Kentucky regulations effective on June 6, 1996.
    (ii) Other material. None.
    (86) Revision to the Kentucky State Implementation Plan submitted by 
the Natural Resources and Environmental Protection Cabinet on May 20, 
1997. The revision is for the Reynolds Metals Company.
    (i) Incorporation by reference. Air Pollution Control District of 
Jefferson County Permit numbers 103-74, 104-74, 105-74, 106-74, 110-74, 
and 111-74, effective April 16, 1997.
    (ii) Other material. None.
[37 FR 10868, Mar. 31, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.920, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.



Sec. 52.921  Classification of regions.

    The Kentucky plan was evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                               Pollutant
                                                      ----------------------------------------------------------
              Air quality control region                                                           Photochemical
                                                       Particulate   Sulfur   Nitrogen   Carbon      oxidants
                                                          matter     oxides    dioxide  monoxide  (hydrocarbons)
----------------------------------------------------------------------------------------------------------------
Appalachian Intrastate...............................          II        III       III       III           III
Bluegrass Intrastate.................................          II        III       III       III           III
Evansville (Indiana)-Owensboro-Henderson (Kentucky)
 Interstate..........................................           I         II       III       III           III
Huntington (West Virginia)-Ashland (Kentucky)-
 Portsmouth-Ironton (Ohio) Interstate................           I        III       III       III           III
Louisville Interstate................................           I          I       III       III             I
Metropolitan Cincinnati Interstate...................           I         II       III       III             I
North Central Kentucky Intrastate....................          II        III       III       III           III
Paducah (Kentucky)-Cairo (Illinois) Interstate.......           I         II       III       III           III
South Central Kentucky Intrastate....................         III        III       III       III           III
----------------------------------------------------------------------------------------------------------------

[37 FR 10868, May 31, 1972, as amended at 39 FR 16346, May 8, 1974]

[[Page 504]]



Sec. 52.922  [Reserved]



Sec. 52.923  Approval status.

    (a) With the exceptions set forth in this subpart, the Administrator 
approves Kentucky's plans for the attainment and maintenance of the 
national standards under section 110 of the Clean Air Act. Furthermore, 
the Administrator finds the plans satisfy all requirements of Part D, 
Title I, of the Clean Air Act as amended in 1977, except as noted below. 
In addition, continued satisfaction of the requirements of Part D for 
the ozone portion of the SIP depends on the adoption and submittal of 
RACT requirements by July 1, 1980 for the sources covered by CTGs issued 
between January 1978 and January 1979 and adoption and submittal by each 
subsequent January of additional RACT requirements for sources covered 
by CTGs issued by the previous January.
    (b) New Source review permits issued pursuant to Section 173 of the 
Clean Air Act will not be deemed valid by EPA unless the provisions of 
Section V of Appendix S of 40 CFR part 51 are met.
[45 FR 72157, Oct. 31, 1980]



Sec. 52.924  Legal authority.

    (a) The requirements of Sec. 51.230(f) of this chapter are not met 
since K.R.S. 224.380 of the Air Pollution Control Law of the 
Commonwealth of Kentucky (June 18, 1970) does not provide for the 
release, under certain circumstances, of emission data to the public.
    (b) Delegation of Authority: Pursuant to section 114 of the Act, 
Kentucky requested a delegation of authority to enable it to collect, 
correlate, and release emission data to the public. The Administrator 
has determined that Kentucky is qualified to receive a delegation of the 
authority it requested. Accordingly, the Administrator delegates to 
Kentucky his authority under section 114(a) (1) and (2) and section 
114(c) of the Act, i.e., authority to collect, correlate, and release 
emission data to the public.
[37 FR 10868, May 31, 1972, as amended at 37 FR 15084, July 27, 1972; 51 
FR 40676, Nov. 7, 1986]



Sec. 52.925  General requirements.

    (a) The requirements of Sec. 51.116(c) of this chapter are not met 
since the legal authority to provide for public availability of emission 
data is inadequate.
[39 FR 34536, Sept. 26, 1974, as amended at 51 FR 40676, Nov. 7, 1986]



Sec. 52.926  Attainment dates for national standards.

    The following table presents the latest dates by which the national 
standards are to be attained. The dates reflect the information 
presented in Kentucky's plan, except where noted.

----------------------------------------------------------------------------------------------------------------
                                                                      Pollutant
                                    ----------------------------------------------------------------------------
     Air quality control region       Particulate matter       Sulfur oxides
                                    --------------------------------------------  Nitrogen    Carbon     Ozone
                                      Primary   Secondary   Primary   Secondary   dioxide    monoxide
----------------------------------------------------------------------------------------------------------------
Appalachian Intrastate:
  a. Bell County...................          g          h          b          b          b          b          b
  b. Perry County..................          g          h          b          b          b          b          b
  c. Whitley County................          g          h          b          b          b          b          b
  d. Rest of AQCR..................          c          c          b          b          b          b          b
Bluegrass Intrastate:
  a. Fayette County................          a          c          b          b          b          b          g
  b. Madison County................          g          h          b          b          b          b          b
  c. Rest of AQCR..................          a          c          b          b          b          b          b
Evansville (Indiana)-Ownsboro-
 Henderson (Kentucky) Interstate:
  a. Daviess County................          g          i          g          g          b          b          b
  b. Henderson County..............          g          i          a          e          b          b          g
  c. Webster County................          c          c          g          g          b          b          b
  d. Rest of AQCR..................          c          c          a          e          b          b          b
Huntington (West Virginia)-Ashland
 (Kentucky)-Portsmouth-Ironton
 (Ohio) Interstate:
  a. Boyd County...................          g          i          g          b          b          b          g
  b. Lawrence County...............          g          h          b          b          b          b          b

[[Page 505]]

  c. Rest of AQCR..................          c          c          b          b          b          b          b
Louisville Interstate..............          g          i          j          j          b          h          h
Metropolitan Cincinnati Interstate:
  a. Boone County..................          c          c          a          d          b          d          h
  b. Campbell County...............          g          h          a          d          b          d          h
  c. Kenton County.................          c          c          a          d          b          d          h
  d. Rest of AQCR..................          c          c          a          d          b          d          c
North Central Kentucky Intrastate:
  a. Bullitt County................          g          h          b          b          b          b          b
  b. Rest of AQCR..................          a          c          b          b          b          b          b
Paducah (Kentucky) Cairo (Illinois)
 Interstate:
  a. McCracken County..............          g          h          g          f          b          b          b
  b. Marshall County...............          c          g          a          f          b          b          b
  c. Muhlenberg County.............          g          h          g          g          b          b          b
  d. Rest of AQCR..................          c          c          a          f          b          b          b
South Central Kentucky Intrastate..          b          b          b          b          b          b          b
----------------------------------------------------------------------------------------------------------------
See Sec.  81.318 of this chapter to identify the specific nonattainment area.
Note: Dates or footnotes in italics are prescribed by the Administrator because the plan did not provide a
  specific date or the dates provided were not acceptable. Sources subject to plan requirements and attainment
  dates established under section 110(a)(2)(A) prior to the 1977 Clean Air Act Amendments remain obligated to
  comply with those requirements by the earlier deadlines. The earlier attainment dates are set out at 40 CFR
  52.926 (1979 edition).
a. Air quality levels presently below primary standards or area is unclassifiable.
b. Air quality levels presently below secondary standards or area is unclassifiable.
c. April 1975.
d. July 1975.
e. July 1977.
f. July 1978.
g. December 31, 1982.
h. December 31, 1987.
i. 18 month extension for plan submittal granted: attainment date not yet established.
j. January 1, 1985.

[45 FR 85002, Dec. 24, 1980]



Sec. 52.927  Compliance schedules.

    (a) The requirements of Sec. 51.262(a) of this chapter are not met 
since compliance schedules with adequate increments of progress have not 
been submitted for every source for which they are required.
    (b) Federal compliance schedules.
    (1) Except as provided in paragraph (b)(5) of this section, the 
owner or operator of any fuel-burning facility subject to the 
requirements of the Kentucky Air Pollution Control Regulations as they 
apply to sulfur dioxide sources, shall notify the Regional 
Administrator, by no later than November 3, 1975, of his intent to 
utilize either low-sulfur fuel or stack gas desulfurization to meet 
these requirements.
    (2) Any owner or operator of a stationary source subject to 
paragraph (b)(1) of this section who elects to utilize low-sulfur fuel 
shall be subject to the following compliance schedule:
    (i) December 1, 1975--Submit to the Regional Administrator a 
projection of the amount of fuel, by types, that will be substantially 
adequate to enable compliance with the applicable regulation on July 1, 
1977, and for at least one year thereafter, as well as a statement as to 
whether boiler modifications will be required. If so, final plans for 
such modifications must be submitted simultaneously.
    (ii) December 31, 1975--Sign contracts with fuel suppliers for 
projected fuel requirements as projected above.
    (iii) December 31, 1975--Let contracts for necessary boiler 
modifications, if applicable.
    (iv) January 30, 1976--Initiate onsite modifications, if applicable.
    (v) May 1, 1977--Complete onsite modifications, if applicable.
    (vi) July 1, 1977--Achieve compliance with the applicable 
regulations, and certify such compliance to the Regional Administrator.

[[Page 506]]

    (3) Any owner or operator subject to paragraph (b)(1) of this 
section who elects to utilize stack gas desulfurization shall be subject 
to the following compliance schedule:
    (i) December 1, 1975--Submit to the Regional Administrator a final 
control plan, which describes at a minimum the steps which will be taken 
by the source to achieve compliance with the applicable regulations.
    (ii) December 31, 1975--Negotiate and sign all necessary contracts 
for emission control systems or process modifications, or issue orders 
for the purchase of component parts to accomplish emission control or 
process modifications.
    (iii) January 30, 1976--Initiate onsite construction or installation 
of emission control equipment or process modification.
    (iv) May 1, 1977--Complete onsite construction or installation or 
emission control equipment or process modification.
    (v) July 1, 1977--Complete shakedown operations and performance 
tests for the applicable unit(s); achieve compliance with Kentucky 
Division of Air Pollution Regulation for sulfur dioxide sources and 
certify such compliance to the Regional Administrator. Ten days prior to 
any performance testing, notice must be given to the Regional 
Administrator to afford him the opportunity to have an observer present.
    (4) Five days after the deadline for completing increments in 
paragraphs (b)(2)(ii) through (b)(2)(v) and (b)(3)(ii) through 
(b)(3)(iv) of this section, certify to the Regional Administrator 
whether the increment has been met.
    (5) (i) None of the above paragraphs shall apply to a source which 
is presently in compliance with applicable regulations. The owner or 
operator of any fuel-burning facility with an aggregate heat input of 
more than 250 million BTU per hour which is presently in compliance, 
shall certify such compliance to the Regional Administrator by November 
3, 1975. The Regional Administrator may request whatever supporting 
information he considers necessary for proper certification.
    (ii) Any compliance schedule adopted by the State and approved by 
the Administrator shall satisfy the requirements of this paragraph for 
the affected source.
    (iii) Any owner or operator subject to a compliance schedule in this 
paragraph may submit to the Regional Administrator no later than 
December 1, 1975, a proposed alternative compliance schedule. No such 
compliance schedule may provide for final compliance after the final 
compliance date in the applicable compliance schedule of this paragraph. 
If approved by the Administrator, such schedule shall satisfy the 
requirements of this paragraph for the affected source.
    (6) Nothing in this paragraph shall preclude the Administrator from 
promulgating a separate schedule for any source to which the application 
of a compliance schedule in this paragraph fails to satisfy the 
requirements of Secs. 51.261 and 51.262(a) of this chapter.
[38 FR 16145, June 20, 1973, as amended at 40 FR 3418, Jan. 22, 1975; 40 
FR 14071, Mar. 28, 1975; 40 FR 29541, July 14, 1975; 40 FR 40160, Sept. 
2, 1975; 51 FR 40675, 40676, 40677, Nov. 7, 1986; 54 FR 25258, June 14, 
1989]



Sec. 52.928  Control strategy: Sulfur oxides.

    The revised SO2 emission limit for large coal-fired 
boilers in Bell, Clark, and Woodford Counties, submitted on June 29, 
1979, is disapproved since it does not provide for attainment and 
maintenance of all SO2 NAAQS. The limit approved by EPA on 
May 10, 1976 (41 FR 19105), remains the limit applicable to these 
sources.
[49 FR 11091, Mar. 23, 1984]



Sec. 52.929  [Reserved]



Sec. 52.930  Control strategy: Ozone.

    (a) The VOC bubble for Alcan Foil Products in Louisville submitted 
as a SIP revision on March 3, 1986, is disapproved. The source must 
continue to meet all the requirements of Jefferson County Regulation 
6.29.
    (b) Part D--disapproval--(1) Campbell and Kenton Counties 
nonattainment area. The 1979 SIP revisions for these two counties are 
disapproved because the Commonwealth failed to submit

[[Page 507]]

evidence of legal authority to implement a vehicle inspection and 
maintenance program as required under section 172(b)(11)(B) of the Clean 
Air Act. No major new or modified sources of volatile organic compounds 
can be built in these two counties by virtue of the provisions of 
section 110(a)(2)(l) of the Clean Air Act.
    (2) Northern Kentucky (Boone, Campbell and Kenton Counties) ozone 
nonattainment area. The demonstration of attainment of the ozone 
standards by the end of 1982, submitted as part of Kentucky's ozone SIP 
revision on June 23, 1982, (draft), September 27, 1982, and November 3, 
1982, is disapproved. As a result, the extension of the attainment 
deadline until December 31, 1987, remains in effect, along with the 
related requirement to submit a SIP revision addressing all requirements 
of Part D extension areas.
    (c) The redesignation request submitted by the Commonwealth of 
Kentucky, on November 11, 1994, for the Kentucky portion of the 
Cincinnati-Northern Kentucky moderate interstate ozone nonattainment 
area from nonattainment to attainment was disapproved on September 27, 
1996.
    (d) Kentucky's November 15, 1996, request for a 1-year attainment 
date extension for the Kentucky portion of the Cincinnati-Hamilton 
metropolitan moderate ozone nonattainment area which consists of Kenton, 
Boone, and Campbell Counties is approved. The date for attaining the 
ozone standard in these counties is November 15, 1997.
    (e) Kentucky's November 15, 1996, request for a 1-year attainment 
date extension for the Kentucky portion of the Louisville moderate ozone 
nonattainment area which consists of Jefferson County and parts of 
Bullitt and Oldham Counties is approved. The date for attaining the 
ozone standard in these counties is November 15, 1997.
    (f) Kentucky's January 7, 1998, request for a 1-year attainment date 
extension for the Kentucky portion of the Cincinnati-Hamilton 
metropolitan moderate ozone nonattainment area which consists of Kenton, 
Boone, and Campbell Counties is approved. The date for attaining the 
ozone standard in these counties is November 15, 1998.
[46 FR 58082, Nov. 30, 1981, as amended at 48 FR 13169, Mar. 30, 1983; 
51 FR 10210, Mar. 25, 1986; 54 FR 10983, Mar. 16, 1989; 60 FR 32469, 
June 22, 1995; 60 FR 40101, Aug. 7, 1995; 61 FR 50720, Sept. 27, 1996; 
62 FR 28637, May 27, 1997; 62 FR 40281, July 28, 1997; 62 FR 55176, Oct. 
23, 1997; 62 FR 61246, Nov. 17, 1997; 63 FR 14625, Mar. 26, 1998]



Sec. 52.931  Significant deterioration of air quality.

    (a) Regulations for preventing significant deterioration of air 
quality. The provisions of Sec. 52.21 (b) through (w) are hereby 
incorporated and made a part of the applicable state plan for the State 
of Kentucky only as they apply to permits issued pursuant to Sec. 52.21 
prior to final approval of Kentucky's Regulation for Prevention of 
Significant Deterioration (PSD), Visibility Monitoring, and Visibility 
New Source Review in Attainment Areas. The provisions of Sec. 52.21 (b) 
through (w) are rescinded for permits issued after final approval of 
Kentucky's Regulation for Prevention of Significant Deterioration (PSD), 
Visibility Monitoring, and Visibility New Source Review in Attainment 
Areas.
    (b) The Commonwealth of Kentucky has committed to revising the 
state's regulations accordingly when EPA amends the federal vessel 
emissions provisions contained in 40 CFR 51.166. In a letter dated 
October 17, 1986, Kentucky stated:

    As requested, the Division of Air Pollution Control hereby commits 
to changing the definition of ``building, structure, facility, or 
installation,'' and any other applicable definitions, when the issue of 
vessel emissions is resolved at the federal level, and after the federal 
regulation, 40 CFR 51.24, is amended.


    (c) In a letter dated May 3, 1988, EPA informed Kentucky that the 
following caveat must be included in all potentially affected permits 
due to a decision of the U.S. Court of Appeals for the District of 
Columbia Circuit (NRDC v. Thomas, 838 F.2d 1224):

    In approving this permit, the Kentucky Division for Air Quality has 
determined that the application complies with the applicable provisions 
of the stack height regulations as revised by the EPA on July 8, 1985 
(50 FR 27892). Portions of the regulations have been

[[Page 508]]

remanded by a panel of the U.S. Court of Appeals for the D.C. Circuit in 
NRDC v. Thomas, 838 F.2d 1224 (D.C. Cir. 1988). Consequently, this 
permit may be subject to modification if and when the EPA revises the 
regulation in response to the court decision. This may result in revised 
emission limitations or may affect other actions taken by the source 
owners or operators.


    Kentucky responded with a letter dated May 11, 1988, stating in 
part:

    This is in response to your letter dated May 3, 1988 * * *. As 
requested by your letter, the Kentucky Division for Air Quality agrees 
to include the condition set forth in your letter, in all potentially 
affected permits issued under regulation 401 KAR 51:017 or 401 KAR 
51:052. Therefore, we request that you consider this letter as our 
commitment that the required caveat will be included in all potentially 
affected permits * * *.
[54 FR 36311, Sept. 1, 1989]



Sec. 52.932  Rules and regulations.

    (a) The last sentence of section 3(1) of Kentucky regulation 401 KAR 
3:050, which specifies that a new fossil fuel fired steam electric 
generator's allowable SO2 emissions may be calculated by 
averaging SO2 emissions from existing units of this type and 
from new ones, is disapproved since it contravenes subpart D of 40 CFR 
part 60, New Source Performance Standards.
    (b) Section 8(2)(a) of regulation 401 KAR 61:015 is disapproved in 
that it allows the Tennessee Valley Authority's Shawnee power plant 
until October 1, 1981, to achieve compliance with emissions limits which 
are not made more stringent by the 1979 Part D revisions, and which the 
source was previously required to meet by July 1, 1977.
    (c) Section 8(2)(d) of regulation 401 KAR 61:015 is disapproved in 
that it allows sources until December 31, 1982, to achieve compliance 
with emission limits which are not made more stringent by the 1979 Part 
D revisions, and which the sources were previously required to meet 
prior to 1979.
[41 FR 19106, May 10, 1976, as amended at 46 FR 40188, Aug. 7, 1981]



Sec. 52.933  Control Strategy: Sulfur oxides and particulate matter.

    In a letter dated March 27, 1987, the Kentucky Department for 
Natural Resources and Environmental Protection certified that no 
emission limits in the State's plan are based on dispersion techniques 
not permitted by EPA's stack height rules. This certification does not 
apply to: Big Rivers-Green 1 & 2, Kentucky Utilities-Ghent 3 & 4, and 
Ashland Oil, Inc.-Catlettsburg.
[54 FR 23478, June 1, 1989]



Sec. 52.934  VOC rule deficiency correction.

    (a) Sections 1.02, 1.08, 6.12, 6.13, 6.16, 6.18, 6.19, 6.23, 6.29, 
6.30, 6.31, 6.32, 6.33, 6.34, 6.35, 7.11, 7.12, 7.16, 7.18, 7.19, 7.23, 
7.52, 7.56, 7.57, 7.58, 7.59, 7.60 and 7.61 of the Jefferson County 
portion of the Commonwealth of Kentucky SIP are being approved. The 
Commonwealth submitted these regulations to EPA for approval on February 
12, 1992. These sections were intended to correct deficiencies cited in 
a letter calling for the Commonwealth to revise its SIP for ozone from 
Greer C. Tidwell, the EPA Regional Administrator, to Governor Wallace G. 
Wilkinson on May 26, 1988, and clarified in a letter from Winston A. 
Smith, Air, Pesticides & Toxics Management Division Director, to William 
C. Eddins, Director of the Commonwealth of Kentucky Division for Air 
Quality.
    (b) Sections 1.05, 1.06, 6.17, 6.36, 6.37, and 6.40 of the Jefferson 
County portion of the Commonwealth of Kentucky SIP are being approved. 
The Commonwealth submitted these regulations to EPA for approval on 
March 4, 1993. These sections were intended to correct deficiencies 
cited in a letter calling for the Commonwealth to revise its SIP for 
ozone from Greer C. Tidwell, the EPA Regional Administrator, to Governor 
Wallace G. Wilkinson on May 26, 1988, and clarified in a letter from 
Winston A. Smith, Air, Pesticides & Toxics Management Division Director, 
to William C. Eddins, Director of the Commonwealth of Kentucky Division 
for Air Quality.
    (c) Deficiencies in 1.12 Emissions Trading, however, have not been 
corrected. The above deficiencies must be corrected according to the 
letters mentioned above, the proposed post-1987 ozone policy (52 FR 
45044), and other

[[Page 509]]

EPA guideline relating to the deficiencies before the SIP for ozone can 
be fully approved.
[59 FR 32352, June 23, 1994]



Sec. 52.935  PM10 State implementation plan development in group II areas.

    On July 7, 1988, the State submitted a committal SIP for the cities 
of Ashland and Catlettsburg in Boyd County. The committal SIP contains 
all the requirements identified in the July 1, 1987, promulgation of the 
SIP requirements for PM10 at 52 FR 24681. The SIP commits the 
State to submit an emissions inventory, continue to monitor for 
PM10, report data and to submit a full SIP if a violation of 
the PM10 National Ambient Air Quality Standards is detected.
[55 FR 4172, Feb. 7, 1990]



Sec. 52.936  Visibility protection.

    (a) The requirements of Section 169A of the Clean Air Act are not 
met because the plan does not include approvable procedures meeting the 
requirements of 40 CFR 51.307 (b) and (c) for protection of visibility 
in mandatory Class I Federal areas from sources in nonattainment areas.
    (b) Regulations for visibility monitoring and new source review. The 
provisions of Sec. 52.28 are hereby incorporated and made part of the 
applicable plan for the State of Kentucky.
[54 FR 36311, Sept. 1, 1989]



Sec. 52.937  Review of new sources and modifications.

    (a) Approval--EPA is approving the section 182(f) oxides of nitrogen 
(NOX) reasonably available control technology (RACT) 
exemption request submitted by the Kentucky Department for Environmental 
Protection on August 16, 1994, for the Kentucky portion of the 
Huntington-Ashland ozone (O3) moderate nonattainment area. 
This approval exempts this area from implementing NOX RACT on 
major sources of NOX. If a violation of the O3 
NAAQS occurs in the area, the exemption from the requirement of section 
182(f) of the CAA in the applicable area shall not apply.
    (b) [Reserved]
[60 FR 21717, May 3, 1995]



                          Subpart T--Louisiana



Sec. 52.970  Identification of plan.

    (a) Title of plan: ``The Louisiana Air Control Commission 
Implementation Plan.''
    (b) The plan was officially submitted on January 28, 1972.
    (c) The plan revisions listed below were submitted on the dates 
specified.
    (1) Certification that public hearings were held on the State's 
implementation plan was submitted on February 28, 1972. (Non-regulatory)
    (2) Response to comments by Region VI on the plan was transmitted by 
the Louisiana Air Control Commission on May 8, 1972. (Non-regulatory)
    (3) Revisions to Louisiana Air Control Regulations 6, 8, 18, 19, 22, 
A22, 27, 28, control strategy for photochemical oxidants-hydrocarbons, 
prevention of air pollution emergency episodes, source surveillance, and 
procedures for submission and approval and compliance schedules were 
submitted by the Governor on July 17, 1972.
    (4) Revisions concerning the control strategy for photochemical 
oxidants and hydrocarbon for Region 106 was submitted by the Governor on 
March 30, 1973. (Regulatory)
    (5) Revision of Section 6.1 of the State air control regulations was 
submitted by the Governor on April 25, 1973.
    (6) A revision concerning the control strategy for particulate 
matter for the Southern Louisiana-Southeast Texas AQCR was submitted by 
the Governor on January 2, 1973.
    (7) Variances to Emission Limiting Regulations adopted by the 
Louisiana Air Control Commission on October 29, 1975, December 12, 1975, 
and April 6, 1976, and submitted by the Governor on April 22, 1976.
    (8) Commission Orders creditable as emission offsets for the GM 
Plant in Shreveport were submitted by the Governor on January 25, 1978 
as amendments to the Louisiana State Implementation Plan.

[[Page 510]]

    (9) A proposed dedesignation of the Shreveport area as an AQMA for 
particulate matter was submitted by the Governor on December 9, 1977.
    (10) An administrative revision of the Air Quality Surveillance 
Network was submitted by the Louisiana Air Control Commission on April 
3, 1978. (Non regulatory)
    (11) Revisions to Regulation 19.0, Emission Standards for 
Particulate Matter, as adopted on November 30, 1977, were submitted by 
the Governor on December 9, 1977.
    (12) Minor changes and administrative revisions to regulations 2.0, 
3.0, 4.0, 5.0, 6.0, 7.0, 8.0, 9.0, 10.0, 11.0, 12.0, 13.0, 14.0, 15.0, 
16.0, and 17.0 of the Louisiana SIP were submitted by the Governor on 
December 9, 1977.
    (13) A variance to Regulation 19.5 for Kaiser Aluminum & Chemical 
Corporation at Norco, Louisiana was submitted by the Governor on August 
31, 1978.
    (14) Revisions to the Air Control Regulations 18.1, 18.3, 18.5, 
18.6-18.6.2, 18.7, 20.1-20.8, 21.1-21.6.4, 23.0-23.4.2, 24.1-24.5, 
24.6.2, 24.7-24.7.3, 24.8, 25.0-25.6.2, 26.0-26.2, 26.4-26.8.2, 27.0-
27.5.4, 28.0-28.6.2 and 30.0, as adopted by the Louisiana Air Control 
Commission on November 30, 1977, were submitted by the Governor on 
December 9, 1977.
    (15) Revisions to the plan for attainment of standards for ozone 
(Part D requirements) were submitted by the Governor on April 30, 1979.
    (16) Evidence of notice and public hearing for the April 30, 1979 
plan was submitted by the Governor on June 20, 1979.
    (17) Emission inventory information, emission reduction information, 
a certification of the lack of major degreasing sources, and a 
commitment to adopt future regulations were submitted by the Louisiana 
Air Control Commission on August 28, 1979 (non-regulatory).
    (18) Schedule for the modification and submittal of regulations 22.6 
and regulation 6.3.8 were submitted by the Louisiana Air Control 
Commission on October 11, 1979 (non-regulatory).
    (19) Regulations 22.17 and 22.18, adopted by the Louisiana Air 
Control Commission on September 25, 1979 were submitted by the Governor 
on October 18, 1979.
    (20) On January 10, 1980, the Governor submitted final revisions to 
the ambient monitoring portion of the plan.
    (21) Revised Regulation 22.8(c) was submitted by the Governor on 
June 20, 1979. This regulation was adopted by the Louisiana Air Control 
Commission on March 27, 1979.
    (22) Revised Regulation 22.5 was submitted by the Governor on April 
30, 1979. This regulation was adopted by the Louisiana Air Control 
Commission on March 27, 1979. A second revision to Regulation 22.5 was 
submitted by the Governor on July 7, 1979, as adopted by the Louisiana 
Air Control Commission on June 26, 1979.
    (23) Revised Regulations 6.3.8, 22.3, 22.6.1, 22.6.2, 22.10, and 
22.12.4 were submitted by the Governor on December 10, 1979. These 
regulations were adopted by the Louisiana Air Control Commission on 
November 27, 1979. A second revision to Regulation 6.3.8 was submitted 
by the Governor on October 23, 1980. The second revision was adopted by 
the Louisiana Air Control Commission on September 25, 1980.
    (24) Revisions to the Air Control Regulations 24.6.1 and 24.7.4, as 
adopted by the Louisiana Environmental Control Commission on March 27, 
1979, were submitted by the Governor on April 30, 1979.
    (25) Revised Regulations 22.9.2, 22.9.3(b), 22.19, 22.20, 22.21, 
22.22 and 22.23 and revised Regulation 4.0 (i.e. sections 4.99 through 
4.116) were adopted by the State on November 27, 1979 and submitted by 
the Governor on December 10, 1979; and revised Regulations 22.3 and 
22.20.2 were adopted by the State on July 22, 1980 and submitted by the 
Governor on September 12, 1980.
    (26) Revised Regulations 22.9.3(b), 22.20.3, and 22.23.7 were 
adopted by the State on December 11, 1980 and submitted by the Governor 
on January 12, 1981; revised Regulation 22.21.2(E) was adopted by the 
State on April 23, 1981 and submitted by the Governor on June 3, 1981; 
and, revised Regulation 22.19.2(B) was adopted by the State on June 25, 
1981 and submitted by the Governor on July 22, 1981.
    (27) Revisions to the Air Control Regulations 6.1.1, 18.2, 18.4, 
18.6.3, 19.5.1, 24.9.1, 24.9.2, 26.3.1, 26.3.2 and 51.11, as

[[Page 511]]

adopted by the Louisiana Environmental Control Commission on September 
25, 1980, were submitted by the Governor on October 23, 1980.
    (28) Revisions to the plan for permit fee systems, interstate 
pollution abatement, public availability of emission data, maintenance 
of pay, permit public comment, and public notification of exceedances of 
the primary national ambient air quality standards (NAAQS), were 
submitted by the Governor on April 30, 1979. In addition, revised 
submittals for permit fee schedules were submitted on July 7, 1979; 
September 12, 1980; October 23, 1980; and January 12, 1981. The 
September 12, 1980 letter also included a new Sec. 51.285 (a), (b) and 
(c). Finally, the State sent a notification letter on August 7, 1979, 
which corrected a typographical error in the maintenance of pay 
revision.
    (29) A revision to the Air Control Regulations 22.9.3(d) as adopted 
by the Louisiana Air Control Commission on December 11, 1980, was 
submitted by the Governor on January 12, 1981.
    (30) Revisions to the Air Control Regulations 8.5.1, 22.3.1.1, 
22.3.1.2, and 22.10, as adopted by the Louisiana Air Control Commission 
on April 23, 1981, were submitted by the Governor on June 3, 1981.
    (31) A revision to the Air Control Regulation 22.9.3(a), as adopted 
by the Louisiana Air Control Commission on May 28, 1981, was submitted 
by the Governor on June 3, 1981.
    (32) A revision to the Air Control Regulation 22.3.2, as adopted by 
the Louisiana Air Control Commission on July 23, 1981, was submitted by 
the Governor on August 17, 1981.
    (33) The Louisiana State Implementation Plan for lead and 
Regulations for--the Control of Air Pollution from lead, 10.0--10.3 and 
19A.0, were submitted to EPA on July 27, 1979, by the Governor of 
Louisiana as adopted by the Louisiana Air Control Commission on July 24, 
1979. Letters of Clarification dated January 6, 1982, April 1, 1982 and 
May 4, 1982 also were submitted. No action is taken on the Baton Rouge 
area.
    (34) Section 6.1 of Regulation 6.0 amended and adopted by the 
Louisiana Environmental Control Commission on October 22, 1981, was 
submitted by the Governor on November 30, 1981.
    (35) Revisions to the Air Control Regulations 4.102, 4.110, 22.20.2 
and 22.21.2(D), as adopted by the Louisiana Environmental Control 
Commission on December 11, 1980, were submitted by the Governor on 
January 12, 1981.
    (36) [Reserved]
    (37) Revisions to the Air Control Regulations 4.14, 4.36, 6.6, 
22.3.1.1, and 22.3.1.2, as adopted by the Louisiana Environmental 
Control Commission on February 26, 1981, were submitted by the Governor 
on March 25, 1981.
    (38) Revisions to the Air Control Regulations 17.13, 23.4.1.1 and 
23.4.4, as adopted by the Louisiana Environmental Control Commission on 
January 28, 1982, were submitted by the Governor on February 15, 1982.
    (39) A revision to section 2210 of the Louisiana Air Control Law was 
submitted to EPA on March 10, 1982. The Section was renamed Section 1077 
of the Environmental Affairs Act, by the Louisiana Legislature, and was 
effective January 1, 1980.
    (40) The Louisiana State Implementation Plan for lead for the Baton 
Rouge area was submitted on July 27, 1979, with letters of clarification 
and revisions dated January 4, 1983, September 15, 1983, September 30, 
1983. The final lead control plan was submitted in a letter dated 
October 31, 1983, as adopted by the Louisiana Air Control Commission on 
October 20, 1983.
    (41) Revisions to sections 2.3, 3.1, 3.4, and 4.1 of the Rules and 
Regulations for the Fee System of the Air Quality Control Program, as 
adopted by the Louisiana Environmental Control Commission on January 26, 
1983, were submitted by the Louisiana Department of Natural Resources 
(now the Department of Environmental Quality), Air Quality Division, on 
November 17, 1983.
    (42) Deletion of Air Control Regulation 14.0, and deletion of 
hydrocarbon guideline standard from Table 1, 1a, and 2, as adopted by 
the Louisiana Environmental Control Commission on July 28, 1983, was 
submitted by the Governor on October 19, 1983.
    (43) Revisions to the Air Control Regulation 22.22 as adopted by the 
Louisiana Environmental Control Commission on September 23, 1982, and 
submitted by the Governor on July 14, 1983.
    (i) Incorporation by reference.

[[Page 512]]

    (A) Regulation 22.22.1(A) and 22.22.2(A) Letter dated July 14, 1983, 
from the State of Louisiana and which change the reference for the test 
methods from a CTG document to the Louisiana Air Quality Regulations 
Division's Source Test Manual. These regulations were adopted on 
September 23, 1982.
    (44) On October 4, 1985, the Governor submitted a revision entitled, 
``Protection of Visibility for Mandatory Class I Federal Areas,'' July 
12, 1985. This submittal included new source review and visibility 
monitoring strategy as adopted by the Secretary of the Louisiana 
Department of Environmental Quality in October 1985.
    (45) On August 14, 1985, the Governor of Louisiana submitted a 
Prevention of Significant Deterioration (PSD) Plan including Air Quality 
Regulations--Part V, (sections 90.1-90.19) as adopted by the Secretary 
of the Department of Environmental Quality on May 23, 1985. Air Quality 
Regulations--Part V provides authority for the State to implement the 
PSD program in certain areas of the State. Letters of commitment for air 
quality modeling (dated September 30, 1985) and Federal stack height and 
dispersion technique regulation (dated June 3, 1986) were submitted by 
the Secretary of Louisiana Department of Environmental Quality.
    (i) Incorporation by reference.
    (A) Louisiana Air Quality Regulations--Part V, Prevention of 
Significant Deterioration of Air Quality, except that no provision of 
this part applies to Indian Reservations meaning any Federally 
recognized reservation established by Treaty, Agreement,Executive Order, 
or Act of Congress, as adopted on May 23, 1985.
    (B) A letter from the Secretary of Louisiana Department of 
Environmental Quality dated September 30, 1985, which commits the 
Department to use only the EPA approved air quality models in accordance 
with the provisions of 40 CFR 51.24(1) [now 40 CFR 51.166(1)] and to 
submit a stack height and dispersion techniques SIP revision by April 8, 
1986.
    (C) A letter from the Secretary of Louisiana Department of 
Environmental Quality dated June 3, 1986, which certifies that the 
Department interprets the provisions of section 90.8 of Louisiana PSD 
regulations as having the same meaning as the Federal stack height and 
dispersion technique regulation, 40 CFR 51.1(hh)-(kk) [now 40 CFR 
51.100(hh)-(kk)], promulgated by EPA in the Federal Register of July 8, 
1985, and that the State will apply, implement, and enforce these 
requirements in the PSD permitting process.
    (D) A narrative explanation and additional requirements entitled 
``Prevention of Significant Deterioration Revisions to the Louisiana 
State Implementation Plan''.
    (46) On January 6, 1988, the Governor of Louisiana submitted a 
revision to the State Implementation Plan (SIP) that contained Air 
Quality Regulations, LAC 33: Part III, Section 921, Stack Heights, as 
adopted by the Secretary of the Department of Environmental Quality on 
December 20, 1987. Section 921, Stack Heights, enables the State to 
ensure that the degree of emission limitation required for the control 
of any air pollutant under its SIP is not affected by that portion of 
any stack height which exceeds GEP or by any other dispersion technique.
    (i) Incorporation by reference.
    (A) Louisiana Air Quality Regulations--LAC 33: Part III, Section 
921, Stack Heights, as adopted by the Secretary of the Department of 
Environmental Quality on December 20, 1987.
    (ii) Other material--none.
    (47) A revision exempting four rural carbon black plants--Ashland 
Chemical, Louisa, LA; Cabot Corporation, Centerville, LA; Cabot 
Corporation, Ville Platte, LA; and Columbian Chemicals, Franklin, LA--
from further controls on acetylene emissions as required under Louisiana 
Air Quality Regulation 22.8 received from the Governor on January 12, 
1987, and amended May 13, 1987.
    (i) Incorporation by reference.
    (A) A letter dated May 29, 1987, from Martha Madden, Secretary, 
Louisiana Department of Environmental Quality, to the Governor of 
Louisiana approving the exemptions from further controls on acetylene 
emissions for the four rural carbon black plants and ordering each 
facility to maintain its emissions at or below the levels specified in 
the attached summary of emissions.

[[Page 513]]

    (ii) Additional material.
    (A) A summary of VOC emissions for each of the four rural carbon 
black plants exempted from further controls on acetylene emissions under 
Louisiana Air Quality Regulation 22.8.
    (48) Part II of the Visibility Protection Plan was submitted by the 
Governor on October 26, 1987.
    (i) Incorporation by reference.
    (A) Revision entitled, ``Louisiana State Implementation Plan 
Revision: Protection of Visibility: Proposed Part II Long-Term Strategy, 
October 26, 1987''. This submittal includes a visibility long-term 
strategy and general plan provisions as approved and adopted by the 
Secretary of the Louisiana Department of Environmental Quality on 
October 26, 1987.
    (B) Letter dated October 26, 1987, from Secretary of Louisiana 
Department of Environmental Quality (LDEQ), to the Governor approving 
the SIP revision.
    (ii) Additional material.
    (A) Letter dated June 16, 1988, from Administrator, Air Quality 
Division, LDEQ, to Chief, SIP/New Source Section (6T-AN), EPA Region 6, 
committing to make its three-year periodic review report available to 
the public as well as to EPA.
    (49) The recodified and revised regulations of the Louisiana 
Administrative Code, Title 33, Part 3 (LAC:33:III) that were adopted by 
the State effective December 20, 1987, and submitted by the Governor by 
letters dated January 6, 1988, and October 4, 1988, for inclusion in the 
SIP. These regulations include LAC:33:III: Chapters 1, 5, 7, 9, 11, 13, 
15, 17, 23, 56, 60, 63, and 65, except LAC:33:III:111 ``Particulate 
matter,'' and ``Suspended particulate matter,'' LAC:33:III:505.J, and 
LAC:33:III:505.L, which were previously disapproved, and 
LAC:33:III:6099, which was withdrawn by the Governor.
    (i) Incorporation by reference. (A) Louisiana Administrative Code, 
Title 33, Part 3, Chapters 1, 5, 7, 9, 11, 13, 15, 17, 23, 56, 60, 63, 
and 65 as adopted by Louisiana Department of Environmental Quality on 
December 20, 1987, except LAC:33:III: section 111 ``Particulate 
matter,'' ``Suspended particulate matter,'' section 505.J, section 
505.L, and section 6099.
    (ii) Additional material. (A) A letter dated December 16, 1987, from 
Martha Madden, Secretary of the Louisiana Department of Environmental 
Quality, to the Governor of Louisiana, approving the codified air 
quality regulations effective December 20, 1987.
    (50) The Louisiana State Implementation Plan for PM10 as 
submitted by the Governor in a letter dated July 26, 1988, and adopted 
by the State effective June 20, 1988.
    (i) Incorporation by reference. (A) Revisions to the Louisiana 
Administrative Code, Title 33, Chapter III, Sections 111, 509.B, 
509.I.8.a, 709, 1301.B, 1303.A, 1305.A., 1311.B, 1311.C, 1313.C, 1315, 
1319.G, 5609.A.1, 5609.A.2, 5609.A.3, and Tables 1, 1a, and 2 of chapter 
7 as adopted effective June 20, 1988.
    (B) A letter dated May 22, 1989, from Mike D. McDaniel, Louisiana 
Department of Environmental Quality, to William B. Hathaway, U.S. 
Environmental Protection Agency.
    (ii) Additional material.
    (A) A letter dated July 26, 1988, from Paul H. Templet, Secretary, 
Louisiana Department of Environmental Quality, to the Governor of 
Louisiana approving the adoption of amendments to the Louisiana Air 
Quality Regulations to implement the new PM10 standard 
effective June 20, 1988.
    (B) A narrative supplement to the Louisiana PM10 
submitted by the Governor in a letter dated July 26, 1988.
    (51) Revision to the Louisiana Lead State Implementation Plan (SIP) 
submitted by the Governor in a letter dated July 18, 1986.
    (i) Incorporation by reference.
    (A) An amended Compliance Order dated January 31, 1986, issued by 
the Secretary of the State of Louisiana Department of Environmental 
Quality in the matter of Ethyl Corporation, Baton Rouge, Louisiana.
    (ii) Additional material.
    (A) Computer modeling submitted by letter dated May 27, 1988, from 
Doug Walters, Louisiana Department of Environmental Quality, to Joe 
Winkler, U.S. Environmental Protection Agency.
    (B) Explanatory letter dated January 27, 1989, from Gustave Von 
Bodungen, Louisiana Department of Environmental Quality, to Gerald 
Fontenot,

[[Page 514]]

U.S. Environmental Protection Agency.
    (52) On October 31, 1983, the Governor submitted a request to revise 
the Louisiana SIP to include an Alternative Emission Reduction Plan for 
the Vulcan Materials Company facility located at Geismar, Ascension 
Parish. A permit was issued by LDEQ on March 24, 1983 (#1829T), but 
after several revisions, the final permit for the trade is #1829T (M-2), 
issued July 28, 1989. This Bubble uses credits obtained from 
installation of a vapor recovery system on a tank farm of five VOC 
storage tanks in lieu of controls on one process vent and one VOC 
storage tank.
    (i) Incorporation by reference.
    (A) LDEQ Permit number 1829T (M-2), Revision of Bubble Permit--
Vulcan Chemicals Company, Geismar, Ascension Parish, Louisiana, issued 
July 28, 1989.
    (ii) Additional material.
    (A) Letter dated June 28, 1989, from the Administrator of the 
Louisiana Office of Air Quality, giving assurances that the State has 
resources and plans necessary to strive toward attainment and 
maintenance of the NAAQS for ozone taking into account the influence of 
this Bubble on air quality.
    (53) On May 5, 1986, the Governor submitted a request to revise the 
Louisiana SIP to include an alternate Emission Reduction Plan for the 
American Cyanamid Company Fortier Plant located at Westwego, Jefferson 
Parish. A permit was issued by LDEQ on October 17, 1984 (1896), but 
after several revisions, the final permit for the trade is 1896 (M-2), 
issued July 20, 1989. This Bubble uses credits obtained from the change 
of service of three storage tanks from VOC to non-VOC usage to offset 
reductions required by controlling one methanol storage tank.
    (i) Incorporation by reference.
    (A) LDEQ permit number 1896 (M-2) issued July 20, 1989, a Revision 
to Bubble Permit No. 1896 (M-1)--American Cyanamid Company, Westwego, 
Jefferson Parish, Louisiana.
    (ii) Additional material.
    (A) Letter dated June 6, 1989, from the Administrator of the 
Louisiana Office of Air Quality, giving the State position that the 
Volatile Organic Compounds that have been shifted out of the emission 
reduction credit donating tanks have not been shifted elsewhere in the 
nonattainment area.
    (B) Letter received by EPA on March 31, 1989, from Mr. Addison Tatum 
of the State of Louisiana, including calculations for the permit.
    (54) A revision to allow an alternative emission reduction plan 
(``bubble'') for the Vista Chemical Company facility in Westlake, 
Louisiana, as submitted by the Governor on November 22, 1983, and 
amended by Louisiana Department of Environmental Quality Air Quality 
Division permit 1828 M-2 issued September 25, 1986.
    (i) Incorporation by reference.
    (A) Louisiana Department of Environmental Quality Air Quality 
Division permit 1828 M-2 issued September 25, 1986.
    (ii) Additional material.--None.
    (55) A revision to allow an alternative emission reduction plan 
[``bubble''] for the Union Carbide facility in Hahnville, Louisiana, as 
submitted by the Governor on October 19, 1983, and amended by Louisiana 
Department of Environmental Quality Air Quality Division permit 
#1836T(M-1) issued April 23, 1987, and revised on May 5, 1990.
    (i) Incorporation by reference.
    (a) Louisiana Department of Environmental Quality Air Quality 
Division permit #1836T(M-1) issued April 23, 1987, and revised on May 5, 
1990.
    (ii) Additional material.--None.
    (56) Revisions to Louisiana's volatile organic compound regulations 
were submitted by the Governor on June 13, 1990.
    (i) Incorporation by reference.
    (A) Revisions to Title 33, Environmental Quality, Part III. Air, 
Chapter 21. Control of Emission of Volatile Organic Compounds, 
Subchapter B. Organic Solvents, Section 2123. Organic Solvents, 
paragraphs C.6. and D.3., effective February 20, 1990.
    (57) Revisions to the Louisiana State Implementation Plan for 
LAC:33:III: Section 509 Prevention of Significant Deterioration (PSD) 
sections (509)(B) (Baseline Area) (1), 509(B) (Baseline Area) (2), 
509(B) (Baseline Concentration) (1), (509)(B) (Baseline Concentration) 
(1)(b), 509(B) (Baseline Concentration) (2)(a), 509(B) (Baseline 
Concentration) (2)(b), 509(B) (Baseline Date)

[[Page 515]]

(1)(a), 509(B) (Baseline Date) (1)(b), 509(B) (Baseline Date) (2), 
509(B) (Baseline Date) (2)(a), 509(B) (Baseline Date) (2)(b), 509(B) 
(Net Emission Increases) (4), 509(D), and 509(P)(4), as adopted by the 
Secretary of Louisiana Department of Environmental Quality (LDEQ) on 
July 20, 1990, were submitted by the Governor on October 26, 1990.
    (i) Incorporation by reference.
    (A) LAG:33:III: Section 509 Prevention of Significant Deterioration 
Sections (509)(B) (Baseline Area) (1), 509(B) (Baseline Area) (2), 
509(B) (Baseline Concentration) (1)(a), (509)(B) (Baseline 
Concentration) (1)(b), 509(B) (Baseline Concentration) (2)(a), 509(B) 
(Baseline Concentration) (2)(b), 509(B) (Baseline Date (1)(a), 509(B) 
(Baseline Date) (1)(b), 509(B) (Baseline Date) (2), 509(B) (Baseline 
Date) (2)(a), 509(B) (Baseline Date) (2)(b), 509(B) (Net Emission 
Increase) (4), 509(D), and 509(P)(4) as amended on July 20, 1990.
    (ii) Additional material.--None.
    (58) Louisiana Air Quality Regulation section 6.6 as revised and 
adopted by the Louisiana Environmental Control Commission on February 
26, 1981, submitted by the Governor on March 25, 1981, and approved by 
the Environmental Protection Agency on June 9, 1982.
    (i) Incorporation by reference. (A) Louisiana Air Quality Regulation 
section 6.6 as revised and adopted by the Louisiana Environmental 
Control Commission on February 26, 1981, submitted by the Governor on 
March 25, 1981, and approved by the Environmental Protection Agency on 
June 9, 1982.
    (ii) Additional material. (A) Letter dated March 24, 1981, from the 
Secretary of the Louisiana Department of Natural Resources to the 
Governor of Louisiana acknowledging approval of Louisiana Air Quality 
Regulation section 6.6 by the Louisiana Environmental Control Commission 
effective on February 26, 1981.
    (59) A revision to the Louisiana State Implementation Plan (SIP) to 
include revisions to LAC, Title 33, ``Environmental Quality,'' Part III. 
Air, Chapter 15. Emission Standards for Sulfur Dioxide, effective April 
20, 1992, and submitted by the Governor by cover letter dated August 5, 
1992.
    (i) Incorporation by reference.
    (A) Revisions to LAC, Title 33, ``Environmental Quality,'' Part III. 
Air, Chapter 15. Emission Standards for Sulfur Dioxide, Section 1501, 
``Degradation of Existing Emission Quality Restricted;'' Section 1503, 
``Emission Limitations;'' Table 4, ``Emissions--Methods of Contaminant 
Measurement;'' Section 1505, ``Variances;'' Section 1507, 
``Exceptions;'' Section 1509, ``Reduced Sulfur Compounds (New and 
Existing Sources);'' Section 1511, ``Continuous Emissions Monitoring;'' 
and Section 1513, ``Recordkeeping and Reporting,'' effective April 20, 
1992.
    (60) A revision to the Louisiana State Implementation plan (SIP) to 
include revisions to Louisiana Administrative Code (LAC), Title 33, 
Environmental Quality, Part III. Air, Chapter 1, Chapter 21, and Chapter 
61 as submitted by the Governor on June 13, 1990, October 26, 1990, May 
24, 1991, and March 24, 1992.
    (i) Incorporation by reference.
    (A) LAC, Title 33, Environmental Quality, Part III. Air, Chapter 21 
(December 1987). Control of Emission of Organic Compounds, except 
section 2105. Storage of Volatile Organic Components (Small Tanks).
    (B) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air, Chapter 1. General Provisions, section 111. Definitions-
Administrator, Administrative Authority*, Attainment Areas, 
Nonattainment Areas, SIP, Volatile Organic Compound, and Chapter 21. 
Control of Emission of Organic Compounds, Subchapter A. General, section 
2103. Storage of Volatile Organic Compounds paragraphs A., C., D.1., 
D.1.a. through D.1.d., D.2., D.2.a., D.2.b., D.3., E., F., H.1., H.2., 
I. effective January 20, 1990.
    (C) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air, Chapter 21. Control of Emission of Organic Compounds Subchapter A. 
General, section 2107. Volatile Organic Compounds-Loading, section 2109. 
Oil/Water-Separation, paragraphs A.1. through A.4., B. through D., 
section 2113. Housekeeping, paragraphs A.1 through A.3., A.5., section 
2117. Exemptions, section 2119. Variances B., and Subchapter D. Cutback 
Paving Asphalt section 2127. Cutback Paving Asphalt, paragraphs A., B., 
C.1., C.2., C.3., D.,

[[Page 516]]

D.1., D.1.b., D.1.c., D.1.d., and D.2., effective February 20, 1990.
    (D) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air, Chapter 21. Control of Emission of Organic Compounds, Subchapter B. 
Organic Solvents, section 2123. Organic Solvents, paragraphs C., C.1. 
through C.5., C.7. through C.9., effective February 20, 1990.
    (E) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air, Chapter 21. Control of Emission of Organic Compounds, Subchapter F. 
Gasoline Handling, section 2131. Filling of Gasoline Storage Vessels, 
paragraphs A., B., B.1., B.3., D., D.1., D.4., D.5., E., F., and G., 
section 2133. Gasoline Bulk Plants paragraphs A., A.1., A.3. through 
A.6., B., B.3., B.4., C. and D., section 2135. Bulk Gasoline Terminals 
paragraphs A., B., B.1.a., B.1.a.i., B.1.a.iii., B.1.d., B.2. through 
B.5., and C. through E., E.1. through E.4., and section 2137. Gasoline 
Terminal Vapor-Tight Control Procedure. effective July 20, 1990.
    (F) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air, Chapter 21. Control of Emission of Organic Compounds Subchapter A. 
General, section 2101. Compliance Schedules, section 2115. Waste Gas 
Disposal paragraphs A., B., C., D., F., G., H., I.1. through I.5., J. 
through K., section 2121. Fugitive Emission Control paragraphs B., B.1, 
B.2., C., C.1.b., C.1.b.i., C.1.b.ii., C.1.b.iii., C.1.c, C.2., C.2.b., 
C.2.b.i., C.4., C.4.c., C.4.d., C.5. and G., Subchapter C. Vapor 
Degreasers, section 2125. Vapor Degreasers paragraphs A., A.1., A.2., 
A.2.i. through A.2.m., A.3., A.3.a. through A.3.d., B., B.1., B.7., 
B.8., C., C.1., C.1.a. through C.1.c., C.1.i., C.1.j., and D. through 
G., Subchapter E. Perchloroethylene Dry Cleaning Systems, section 2129. 
Perchloroethylene Dry Cleaning Systems paragraphs A., A.1., A.2., A.2.a. 
through A.2.c., C., and D., Subchapter H. Graphic Arts, section 2143. 
Graphic Arts (Printing) by Rotogravure and Flexographic Processes 
paragraphs A., A.1., A.3., A.5., B., C. and D., Subchapter I. 
Pharmaceutical Manufacturing Facilities, section 2145. Pharmaceutical 
Manufacturing Facilities, paragraphs A., A.1., A.1.c., and E. through G. 
effective November 20, 1990.
    (G) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air, Chapter 21. Control of Emissions of Organic Compounds Subchapter A. 
General, section 2103. Storage of Volatile Organic Compounds paragraphs 
B.,D., D.2.c. through D.2.e., G., H.3., I.2.c., I.4. and I.5., section 
2107. Volatile Organic Compounds-Loading paragraphs D.3. and D.4., 
section 2109. Oil/Water Separation paragraphs A., B.4., and B.5., 
section 2111. Pumps and Compressors, section 2113. Housekeeping 
paragraph A.4., section 2119. Variances paragraph A.; Subchapter D. 
Cutback Paving Asphalt, section 2127. Cutback Paving Asphalt paragraphs 
C. and D.1.a. effective April 20, 1991.
    (H) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air, Chapter 21. Control of Emission of Organic Compounds, section 2115. 
Waste Gas Disposal paragraphs I., K., and K.4., section 2121. Fugitive 
Emission Control paragraphs A., C.1., C.1.b.iv. through C.1.b.vi., 
C.4.a., C.4.b., C.4.h., D., D.1., D.1.b. through D.1.f., and D.2., 
seciton 2123. Organic Solvents paragraphs A., A.1. through A.3., B., 
B.1., B.1.a. through B.1.c., C.11., D., D.1. through D.9., E., E.1. 
through E.7., F., and F.1. through F.4., Subchapter F. Gasoline 
Handling, section 2131. Filling of Gasoline Storage Vessels paragraphs 
D.2. and D.3., section 2135. Bulk Gasoline Terminals paragraph E.5., 
Subchapter G-Petroleum Refinery Operations, section 2139. Refinery 
Vacuum Producing Systems paragraphs A. and B. and section 2141. Refinery 
Process Unit Turnarounds effective July 20, 1991.
    (I) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air, Chapter 61. Division's Sources Test Manual, Subchapter A. Method 
43-Capture Efficiency Test Procedures section 6121 through section 6131 
effective July 20, 1991.
    (J) Revisions to LAC, Title 33, Environmental Quality, Part III. Air 
Chapter 1. General Provisions, section 111. Definitions-Coating, 
Department, Distance from Source to Property Line, Exceedance, 
Hydrocarbon, Leak, Miscellaneous Metal Parts and Products Coating, 
Nonattainment Area, Ozone Exceedance, SIP effective August 20, 1991.

[[Page 517]]

    (61) A revision to the Louisiana SIP to include revisions to LAC, 
Title 33, ``Environmental Quality,'' Part III. Air, Chapter 21, Control 
of Emission of Organic Compounds, Section 2132--Stage II Vapor Recovery 
Systems for Control of Vehicle Refuelling Emissions at Gasoline 
Dispensing Facilities effective November 20, 1992, and submitted by the 
Governor by cover letter dated November 10, 1992.
    (i) Incorporation by reference.
    (A) Revisions to LAC, Title 33, ``Environmental Quality,'' Part III. 
Air, Chapter 21, Control of Emission of Organic Compounds, Section 
2132--Stage II Vapor Recovery Systems for Control of Vehicle Refuelling 
Emissions at Gasoline Dispensing Facilities, effective November 20, 
1992; and Chapter 65, Section 6523--Fee Schedule Listing, effective 
November 20, 1992.
    (ii) Additional materials.
    (A) November 15, 1993, narrative plan addressing: Legal authority, 
control strategy, compliance schedules, air quality surveillance, public 
notice, determination of regulated universe, Louisiana Department of 
Environmental Quality recordkeeping, facility recordkeeping, annual in-
use above ground inspections, program penalties, training, and benefits.
    (62) Alternative emission reduction (bubble) plan for the Dow 
Chemical facility located in Plaquemine, Iberville Parish, as adopted by 
the Louisiana Environmental Control Commission on July 28, 1983, 
submitted by the Governor on October 19, 1983, and amended by the 
Louisiana Department of Environmental Quality with permit number 
1838T(M-2) issued on October 16, 1991.
    (ii) Incorporation by reference.
    (A) Permit number 1838T(M-2) as issued by the Louisiana Department 
of Environmental Quality on October 16, 1991.
    (ii) Additional material.
    (A) Letter dated September 17, 1991, from the Administrator of the 
Office of Air Quality at the Louisiana Department of Environmental 
Quality to the Chief of the Planning Section at the Air Programs Branch 
of the U.S. Environmental Protection Agency--Region 6, furnishing State 
assurances.
    (63) The State is required to implement a Small Business Stationary 
Source Technical and Environmental Compliance Assistance Program 
(PROGRAM) as specified in the plan revision submitted by the Governor on 
October 22, 1992. This plan submittal, as adopted by the Secretary of 
the Louisiana Department of Environmental Quality (LDEQ) on October 22, 
1992, was developed in accordance with section 507 of the Clean Air Act 
(CAA).
    (i) Incorporation by reference.
    (A) Enrolled House Bill No. 1319 (Act 1037, Regular Session, 1992), 
signed into law by the Governor on July 13, 1992, and effective upon 
signature, enacting Louisiana Revised Statutes (R.S.) 30:2061 and 2062 
and R.S. 36:239(H). Included in Act 1037 are provisions establishing a 
small business stationary source compliance assistance program; creating 
the State Ombudsman Office for small business; creating a Compliance 
Advisory Panel (CAP); establishing membership of the CAP; and 
establishing CAP powers, duties, and functions.
    (B) Louisiana R.S. 30:2060N.(6), ``Toxic air pollutant emission 
control program'', (the small business stationary source technical and 
environmental compliance assistance program subsection), as in effect on 
October 22, 1992.
    (C) State of Louisiana Executive Order No. EWE 92-4 dated February 
10, 1992, and effective upon signature, creating and establishing an 
Office of Permits within the Executive Department, Office of the 
Governor.
    (D) Letter from Louisiana Governor Edwards to Mr. Kai Midboe, 
Secretary, LDEQ, dated February 20, 1992, designating the Governor's 
Office of Permits as the official State office to serve as Ombudsman for 
the PROGRAM per the mandate of section 507 of the Federal CAA. The 
Coordinator of the Office of Permits will be responsible for 
administering the Small Business Ombudsman portion of the PROGRAM.
    (ii) Additional material.
    (A) Narrative SIP Revision entitled, ``Louisiana SIP, Concerning CAA 
Amendments of 1990, Section 507, Small Business Stationary Source 
Technical and Environmental Compliance Assistance (Program); November 
15, 1992.''

[[Page 518]]

    (B) ``State of Louisiana Memorandum of Understanding Between the 
Governor's Office of Permits and the Louisiana Department of 
Environmental Quality'', signed (and effective) on April 7, 1992, by Mr. 
Kai David Midboe, Secretary, LDEQ, and Ms. Martha A. Madden, 
Coordinator, Governor's Office of Permits.
    (C) Legal opinion letter dated October 22, 1992, from James B. 
Thompson, III, Assistant Secretary for Legal Affairs and Enforcement, 
LDEQ, to Mr. B. J. Wynne, Regional Administrator, EPA Region VI, 
regarding ``Appointment to Small Business Advisory Panel''.
    (64) Revisions to the Louisiana SIP addressing VOC RACT catch-up 
requirements were submitted by the Governor of Louisiana by letters 
dated December 21, 1992, and April 14, 1993.
    (i) Incorporation by reference.
    (A) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air; Chapter 21. Control of Emissions of Organic Compounds, Subchapter 
A. General; section 2103. Storage of Volatile Organic Compounds, 
paragraphs G., I., I.4.; section 2109. Oil/Water Separation, paragraph 
B.4.; Subchapter B. Organic Solvents; section 2123. Organic Solvents, 
paragraph D.6.; Subchapter C. Vapor Degreasers; section 2125. Vapor 
Degreasers, paragraph D.; Subchapter F. Gasoline Handling; section 2131. 
Filling of Gasoline Storage Vessels, paragraphs D., D.1., D.3., G.; 
section 2135. Bulk Gasoline Terminals, paragraph A.; Subchapter H. 
Graphic Arts; section 2143. Graphic Arts (Printing) by Rotogravure and 
Flexographic Processes, paragraph B, as adopted by LDEQ on October 20, 
1992.
    (B) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air; Chapter 21. Control of Emissions of Organic Compounds, Subchapter 
A. General; section 2115. Waste Gas Disposal, introductory paragraph, 
paragraphs H., H.1., H.1.a through H.1.d, H.2, H.2.a, H.2.b, H.3, L., as 
adopted by LDEQ on March 20, 1993.
    (ii) Additional material.
    (A) Letters dated November 10, 1992 and December 21, 1992, signed by 
Edwin Edwards, Governor of Louisiana.
    (B) Letter dated April 14, 1993, signed by Edwin Edwards, Governor 
of Louisiana.
    (C) Letter of negative declaration dated March 29, 1994, signed by 
Gustave Von Boduungen, P.E., Assistant Secretary, LDEQ.
    (65) Revisions to the Louisiana Department of Environmental Quality 
Regulation Title 33, Part III, Chapter 9, Section 919, (February 2, 
1993), and a technical correction (October 20, 1994). These revisions 
are for the purpose of implementing an emission statement program for 
stationary sources within the ozone nonattainment areas.
    (i) Incorporation by reference.
    (A) Revisions to LAC, title 33, Part III, Chapter 9, General 
Regulations on Control of Emissions and Emissions Standards, Section 
919, Emission Inventory, adopted in the Louisiana Register, Vol. 19, No. 
2, 184-186, February 20, 1993. All subsections except B.2.a. and B.2.d.
    (B) Revisions to LAC, title 33, Part III, Chapter 9, General 
Regulations on Control of Emissions and Emissions standards, Section 
919, Emission Inventory, adopted in the Louisiana Register, Vol 20, No. 
10, 1102, October 20, 1994. Subsections B.2.a. and B.2.d.
    (66) Revisions to the Louisiana Department of Environmental Quality 
Regulation Title 33, Part III, Chapter 2, Section 223 and Chapter 19, 
Sections 1951-1973. These revisions are for the purpose of implementing 
a Clean Fuel Fleet Program to satisfy the Federal requirements for a 
Clean Fuel Fleet Program to be part of the SIP for Louisiana.
    (i) Incorporation by reference.
    (A) Revision to LAC, Title 33, Part III, Chapter 2, Rules and 
Regulations for the Fee System of the Air Quality Control Programs, 
Section 223, Fee Schedule Listing, adopted in the Louisiana Register, 
Vol. 20, No. 11, 1263, November 20, 1994.
    (B) Revision to LAC, Title 33, Part III, Chapter 19, Mobile Sources, 
Subchapter B, Clean Fuel Fleet Program, Sections 1951-1973, adopted in 
the Louisiana Register, Vol. 20, No. 11, 1263-1268, November 20, 1994.
    (67) A revision to the Louisiana State Implementation Plan for 
General Conformity: LAC 33:III. CHAPTER 14.

[[Page 519]]

SUBCHAPTER A ``Determining Conformity of General Federal Actions to 
State or Federal Implementation Plan'' as adopted by the Louisiana 
Department of Environmental Quality Secretary and published in the 
Louisiana Register, Vol. 20, No. 11, 1268, November 20, 1994, was 
submitted by the Governor on November 10, 1994.
    (i) Incorporation by reference.
    (A) Louisiana General Conformity: LAC 33:III. CHAPTER 14. SUBCHAPTER 
A ``Determining Conformity of General Federal Actions to State or 
Federal Implementation Plan'' as adopted by the Louisiana Department of 
Environmental Quality Secretary and published in the Louisiana Register, 
Vol. 20, No. 11, 1268, November 20, 1994.
    (68) A revision to the Louisiana SIP addressing the nonattainment 
NSR program for Louisiana was submitted by the Governor of Louisiana on 
March 3, 1993, and November 15, 1993.
    (i) Incorporation by reference.
    (A) Revision to LAC, Title 33, Part III. Air, Chapter 5. Permit 
Procedures, by the addition of Section 504. Nonattainment New Source 
Review Procedures, as promulgated in the Louisiana Register, Volume 19, 
Number 2, 176-183, February 20, 1993; effective February 20, 1993, and 
submitted by the Governor on March 3, 1993.
    (B) Revisions to LAC, Title 33, Part III. Air, Chapter 5. Permit 
Procedures, Section 504. Nonattainment New Source Review Procedures, 
Subsections: A., Applicability, Paragraphs A(1), A(2), A(3), A(4); D., 
Nonattainment New Source Requirements, Paragraph D(4); Delete G., Permit 
Procedures, Public Participation and Notification; Reletter H., 
Definitions, to G., and revise definitions for Major Modification 
(paragraphs: a., c.iii, c.iv, c.v.(a)(b), c.vi, c.vii), Major Stationary 
Source (paragraphs: a., d.i); Delete Table 1; Renumber Table 2, Major 
Stationary Source/Major Modification Emission Thresholds, to Table 1, 
and revise Footnote 1., as promulgated in the Louisiana Register, Volume 
19, Number 11, 1420-1421, November 20, 1993; effective November 20, 
1993, and submitted by the Governor on November 4, 1993.
    (ii) Additional material.
    (A) Letter dated January 7, 1994, signed by the Governor of 
Louisiana, which clarifies that section 504 is to be reviewed under the 
SIP program.
    (69) The Governor of Louisiana submitted revisions to Regulation 
Louisiana Administrative Code on March 22, 1995 to incorporate changes 
in the Federal PSD permitting regulations for PM-10 increments.
    (i) Incorporation by reference.
    (A) Revisions to Regulation Louisiana Administrative Code 
33:III.Chapter 5, Section 509, effective February 20, 1995: Section B. 
Definitions: Baseline Date; Section B. Definitions: Net Emissions 
Increase; Section D. Ambient Air Increments; Section I.8.a.; Section 
K.2.; and Section P.4.
    (70) The Louisiana Department of Environmental Quality submitted a 
redesignation request and maintenance plan for Pointe Coupee Parish on 
December 20, 1995. The redesignation request and maintenance plan meet 
the redesignation requirements in section 107(d)(3)(E) of the Act as 
amended in 1990. The redesignation meets the Federal requirements of 
section 182(a)(1) of the Clean Air Act as a revision to the Louisiana 
ozone State Implementation Plan for Pointe Coupee Parish. The EPA 
therefore approved the request for redesignation to attainment with 
respect to ozone for Pointe Coupee Parish on December 20, 1996.
    (i) Incorporation by reference. Letter dated August 31, 1995, from 
Mr. Gustave Von Bodungen, P.E., Assistant Secretary, Louisiana 
Department of Environmental Quality, transmitting a copy of the Pointe 
Coupee Parish maintenance plan for the EPA's approval.
    (ii) Additional material.
    (A) Letter dated August 28, 1995, from Governor Edwin E. Edwards of 
Louisiana to Ms. Jane Saginaw, Regional Administrator, requesting the 
reclassification and redesignation of Pointe Coupee Parish to attainment 
for ozone.
    (B) The ten year ozone maintenance plan, including emissions 
projections and contingency measures, submitted to EPA as part of the 
Pointe Coupee Parish redesignation request on December 20, 1995.
    (71) A revision to the Louisiana SIP addressing the 15 percent rate-
of-progress requirements was submitted

[[Page 520]]

by the Governor of Louisiana by cover letter dated December 15, 1995. 
This revision, submitted to satisfy the requirements of section 182(b) 
of the Clean Air Act (Act), will aid in ensuring that reasonable further 
progress is made towards attaining the national ambient air quality 
standard (NAAQS) for ozone.
    (i) Incorporation by reference.
    (A) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air; Chapter 21. Control of Emissions of Organic Compounds, Subchapter 
A. General; section 2108. Marine Vapor Recovery, paragraphs B.1., B.2., 
B.3., B.3.a. through B.3.d., B.4.a., B.4.b., B.5., B.6., D.1.a., 
D.1.a.i., D.1.a.ii., D.1.b., D.2., D.3., D.4.a., D.4.b., D.4.c., 
D.4.c.i., D.4.c.ii., D.4.d., D.4.e., D.4.e.i., D.4.e.ii., D.4.f., 
D.4.g., E.2., E.2.a. through E.2.c., F.1., F.2., F.3., G.1., G.2., as 
adopted by LDEQ on October 20, 1988.
    (B) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air; Chapter 21. Control of Emissions of Organic Compounds, Subchapter 
A. General; section 2108. Marine Vapor Recovery, paragraphs A., B. 
Definitions-Barge, Crude Oil, Gasoline, Ship, C., C.1., C.2., C.3., 
C.3.a. through C.3.d. (note: paragraphs B.1., B.2., B.3., and B.3.a. 
through B.3.d., as adopted on October 20, 1988, were moved to C.1., 
C.2., C.3., and C.3.a. through C.3.d. without repromulgating), C.4., 
C.4.a., C.4.b., C.5., C.6. (note: paragraphs B.4.a., B.4.b., B.5., and 
B.6., as adopted on October 20, 1988, were moved to C.4.a., C.4.b., 
C.5., and C.6. without repromulgating), D.1., D.1.a. through D.1.c., 
D.2., D.2.a. through D.2.c., D.3., E., E.1., E.1.a., E.1.a.i., 
E.1.a.ii., E.1.b., E.2., E.3. (note: D.1.a., D.1.a.i., D.1.a.ii., 
D.1.b., D.2., and D.3., as adopted October 20, 1988, were moved to 
E.1.a., E.1.a.i., E.1.a.ii., E.1.b., E.2., and E.3. without 
repromulgating), E.4., E.4.a., E.4.b., E.4.c., E.4.c.i., E.4.c.ii., 
E.4.d., E.4.e., E.4.e.i., E.4.e.ii., E.4.f., E.4.g. (note: D.4.a., 
D.4.b., D.4.c., D.4.c.i., D.4.c.ii., D.4.d., D.4.e., D.4.e.i., 
D.4.e.ii., D.4.f., and D.4.g, as adopted on October 20, 1988, were moved 
to E.4.a., E.4.b., E.4.c., E.4.c.i., E.4.c.ii., E.4.d., E.4.e., 
E.4.e.i., E.4.e.ii., E.4.f., and E.4.g. without repromulgating), E.5., 
F., F.1., F.2., F.2.a. through F.2.e. (note: E.2. and E.2.a. through 
E.2.c., as adopted on October 20, 1988, were moved to F.2. and F.2.a 
through F.2.c. without repromulgating), G., G.1., G.2., G.3. (note: 
F.1., F.2., and F.3., as adopted October 20, 1988, were moved to G.1., 
G.2., and G.3. without repromulgating), H., H.1., H.2. (note: G.1. and 
G.2., as adopted on October 20, 1988, were moved to H.1. and H.2. 
without repromulgating), as adopted by LDEQ on November 20, 1990.
    (C) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air; Chapter 21. Control of Emissions of Organic Compounds, Subchapter 
A. General; section 2122. Fugitive Emission Control for Ozone 
Nonattainment Areas, paragraphs A., A.1. through A.5., A.6., A.6.a. 
through A.6.d., B. Definitions-Connector, Good Performance Level, Heavy 
Liquid Service, Inaccessible Valve/Connector, In Vacuum Service, Light 
Liquid, Light Liquid Service, Liquid Service, Process Unit, Process Unit 
Shutdown, Unrepairable Component, C., C.1., C.1.a. through C.1.c., C.2. 
through C.5., D., D.1., D.1.a., D.1.a.i., D.1.a.ii., D.1.b., D.1.b.i. 
through D.1.b.v., D.1.c. through D.1.e., D.2., D.2.a., D.2.b., D.2.b.i. 
through D.2.b.iii., D.3., D.3.a. through D.3.d., D.4., D.4.a. through 
D.4.k., D.5., E.1.a. through E.1.f., E.2., E.3., E.3.a., E.3.a.i. 
through E.3.a.v., E.3.b., E.3.b.i. through E.3.b.v., F., F.1., F.2., 
F.2.a. through F.2.j., F.3., G., G.1. through G.13., as adopted by LDEQ 
on October 20, 1994.
    (D) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air; Chapter 21. Control of Emissions of Organic Compounds, Subchapter 
A. General; section 2122. Fugitive Emission Control for Ozone 
Nonattainment Areas, paragraphs E., E.1., E.1.g., as adopted by LDEQ on 
November 20, 1994.
    (E) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air; Chapter 21. Control of Emissions of Organic Compounds, Subchapter 
A. General; section 2103. Storage of Volatile Organic Compounds, 
paragraphs A., B., D.1., D.1.a. through D.1.d., D.2., D.2.a. through 
D.2.e., E., F., G., G.1. through G.4., H., H.1., H.2., H.2.a. through 
H.2.e., H.3., I., I.1., I.2., I.2.a. through I.2.c., I.3. through I.5., 
as adopted by LDEQ on December 20, 1994.
    (F) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air;

[[Page 521]]


Chapter 21. Control of Emissions of Organic Compounds, Subchapter A. 
General; section 2103. Storage of Volatile Organic Compounds, paragraphs 
C., D., D.3., as adopted by LDEQ on November 20, 1995.
    (G) Revisions to LAC, Title 33, Environmental Quality, Part III. 
Air; Chapter 21. Control of Emissions of Organic Compounds, Subchapter 
A. General; section 2103. Storage of Volatile Organic Compounds, 
paragraph D.4., as adopted by LDEQ on December 20, 1995.
    (H) Reasonable Further Progress Agreed To Order, dated December 16, 
1994, issued by the Assistant Secretary of the State of Louisiana 
Department of Environmental Quality in the matter of BASF Corporation, 
Geismar, Louisiana.
    (I) Reasonable Further Progress Agreed To Order, dated August 22, 
1994, issued by the Assistant Secretary of the State of Louisiana 
Department of Environmental Quality in the matter of CosMar Company, 
Inc., Carville, Louisiana.
    (J) Reasonable Further Progress Agreed To Order, dated September 26, 
1994, issued by the Assistant Secretary of the State of Louisiana 
Department of Environmental Quality in the matter of Shell Chemical 
Company, Geismar, Louisiana.
    (K) Reasonable Further Progress Agreed To Order, dated September 8, 
1994, issued by the Assistant Secretary of the State of Louisiana 
Department of Environmental Quality in the matter of Uniroyal Chemical 
Company, Inc., Geismar, Louisiana.
    (L) Reasonable Further Progress Agreed To Order, dated September 8, 
1994, issued by the Assistant Secretary of the State of Louisiana 
Department of Environmental Quality in the matter of Vulcan Chemicals, 
Geismar, Louisiana.
    (M) SIP narrative plan entitled, ``Revision to the 15% Rate of 
Progress Plan and 1990 Emissions Inventory,'' dated December 28, 1995, 
page 11, Section 2.2, 1996 Target Level Emissions, first paragraph; page 
23, Section 5, Table 2--Reductions in Plan; page 173, Appendix G, 
table--Reductions from Industrial Sources through 1996 Used for the 15% 
Requirement, which ends on page 174.
    (ii) Additional materials.
    (A) SIP narrative plan entitled, ``Revision to 15% Rate of Progress 
Plan and 1990 Emissions Inventory,'' submitted by the Governor of 
Louisiana on December 15, 1995, except Section 6. Contingency Measures 
Documentation, Appendix M. Contingency Reductions Documentation, and 
Appendix N. Banking Regulations.
    (B) Letter dated May 3, 1996, from Gustave Von Bodungen, Louisiana 
Department of Environmental Quality, to Thomas Diggs, U.S. Environmental 
Protection Agency, transmitting supplemental documentation for the 15 
Percent Rate of Progress Plan.
    (72) Revisions to the Louisiana SIP addressing VOC RACT Negative 
Declarations. The Governor of Louisiana submitted the negative 
declarations for reasonably available control technology (RACT) for the 
Baton Rouge ozone nonattainment area on December 15, 1996. Section 
172(c)(1) of the Clean Air Act requires nonattainment areas to adopt, at 
a minimum, RACT to reduce emissions from existing sources. Pursuant to 
section 182(b)(2) of the Act, for moderate and above ozone nonattainment 
areas, the EPA has identified 13 categories for such sources and 
developed the Control Technique Guidelines (CTGs) or Alternate Control 
Techniques (ACTs) documents to implement RACT at those sources. When no 
major volatile organic compound (VOC) sources for a CTG/ACT category 
exist in a nonattainment area, a State may submit a negative declaration 
for that category. Louisiana's submittal included two negative 
declaration letters from Mr. Gustave Von Bodungen to Ms. Karen Alvarez 
dated April 6, 1994, and June 20, 1994, for the following source 
categories: offset lithography, plastic parts-business machines, plastic 
parts-others, wood furniture, aerospace coatings, autobody refinishing, 
and shipbuilding coatings/repair. This submittal satisfies section 
182(b)(2) of the Clean Air Act Amendments of 1990 for these particular 
CTG/ACT source categories for the Baton Rouge ozone nonattainment area.
    (i) Incorporation by reference. The letter dated December 15, 1995, 
from the Governor of Louisiana to the Regional Administrator, submitting 
a revision to the Louisiana SIP for VOC

[[Page 522]]

RACT rules, which included VOC RACT negative declarations.
    (ii) Additional material.
    (A) The negative declaration letter dated April 16, 1994, from Mr. 
Gustave Von Bodungen to Ms. Karen Alvarez.
    (B) The negative declaration letter dated June 20, 1994, from Mr. 
Gustave Von Bodungen to Ms. Karen Alvarez.
    (73) The Louisiana Department of Environmental Quality submitted a 
redesignation request and maintenance plan for Calcasieu Parish on 
December 20, 1995. The redesignation request and maintenance plan meet 
the redesignation requirements in section 107(d)(3)(E) of the Act. The 
redesignation meets the Federal requirements of section 182(a)(1) of the 
Act as a revision to the Louisiana ozone State Implementation Plan for 
Calcasieu Parish. The EPA therefore approved the request for 
redesignation to attainment with respect to ozone for Calcasieu Parish 
on June 2, 1997.
    (i) Incorporation by reference. Letter dated December 20, 1995, from 
Governor Edwin E. Edwards of Louisiana to Ms. Jane Saginaw, Regional 
Administrator, transmitting a copy of the Calcasieu Parish maintenance 
plan and requesting the redesignation of Calcasieu Parish to attainment 
for ozone.
    (ii) Additional material. The ten year ozone maintenance plan, 
including emissions projections and contingency measures, submitted to 
EPA as part of the Calcasieu Parish redesignation request on December 
20, 1995.
    (74) Revisions to the Louisiana Department of Environmental Quality 
Regulation Title 33, Part III, Chapter 21, Control of Emission of 
Organic Compounds, submitted by the Governor on December 15, 1995.
    (i) Incorporation by reference.
    (A) LAC, Title 33, Part III, Chapter 21, Section 2147, Limiting 
Volatile Organic Compound Emissions from Reactor Processes and 
Distillation Operations in the Synthetic Organic Chemical Manufacturing 
Industry, adopted in the Louisiana Register on April 20, 1995 (LR 
21:380).
    (B) LAC, Title 33, Part III, Chapter 21, Section 2149, Limiting 
Volatile Organic Compound Emissions from Batch Processing, adopted in 
the Louisiana Register on April 20, 1995 (LR 21:387).
    (C) LAC, Title 33, Part III, Chapter 21, Section 2151, Limiting 
Volatile Organic Compound Emissions from Cleanup Solvent Processing, 
adopted in the Louisiana Register on April 20, 1995 (LR 21:391).
    (ii) Additional material.
    (A) Letter of negative declaration for wood furniture dated January 
21, 1997, from the State of Louisiana Department of Environmental 
Quality.
    (75) A revision to the Louisiana State Implementation Plan for 
General Conformity: LAC 33:III. Chapter 14. Subchapter A ``Determining 
Conformity of General Federal Actions to State or Federal Implementation 
Plan,'' Section 1405.B as adopted by the Louisiana Department of 
Environmental Quality Secretary and published in the Louisiana Register, 
Vol. 23, No. 6, 720, June 20, 1997, was submitted by the Governor on 
September 8, 1997.
    (i) Incorporation by reference.
    (A) Louisiana General Conformity: LAC 33:III. Chapter 14. Subchapter 
A ``Determining Conformity of General Federal Actions to State or 
Federal Implementation Plan'', Section 1405.B as adopted by the 
Louisiana Department of Environmental Quality Secretary and published in 
the Louisiana Register, Vol. 23, No. 6, 720, June 20, 1997.
    (79) Site-specific revision to the 15% Rate-of-Progress plan 
submitted by the Governor in a letter dated December 20, 1997. The 
revision provides for a schedule extension for installation of guide 
pole sliding cover gaskets on 33 external floating roof tanks located at 
the Baton Rouge refinery of Exxon Company U.S.A.
    (i) Incorporation by reference. Letters dated July 17, 1997, and 
September 12, 1997, from the LDEQ to Exxon Company U.S.A. approving the 
compliance date extension; which are included in the State 
Implementation Plan submittal entitled, ``Summary of 15% Rate-of-
Progress State Implementation Plan Revision,'' dated December 20, 1997.
    (ii) Additional material.
    (A) Letter from the Governor of Louisiana dated December 20, 1997, 
transmitting a copy of the State Implementation Plan revision.

[[Page 523]]

    (B) Letters dated November 13, 1996; May 14, 1997; and July 3, 1997; 
from Exxon Company U.S.A. to the LDEQ requesting the compliance date 
extension and including a list of the subject tanks, the date of the 
next maintenance downtime, and emissions estimates for the tanks; which 
are included in the State Implementation Plan submittal entitled, 
``Summary of 15% Rate-of-Progress State Implementation Plan Revision,'' 
dated December 20, 1997.
[37 FR 10869, May 31, 1972]

    Editorial Note: For Federal Register citations affecting 
Sec. 52.970, see the List of CFR Sections Affected in the Finding Aids 
section of this volume.

    Effective Date Note:  At 63 FR 25775, May 11, 1998, Sec. 52.970 was 
amended by adding paragraph (c)(79), effective July 10, 1998.



Sec. 52.971  Classification of regions.

    The Louisiana plan was evaluated on the basis of the following 
classifications:

----------------------------------------------------------------------------------------------------------------
                                                                                  Pollutant
                                                           -----------------------------------------------------
                Air quality control region                  Particulate   Sulfur   Nitrogen   Carbon
                                                               matter     oxides    dioxide  monoxide    Ozone
----------------------------------------------------------------------------------------------------------------
Southern Louisiana-Southeast Texas Interstate.............          II          I       III       III          I
Shreveport-Texarkana-Tyler Interstate.....................          II        III       III       III        III
Monroe-El Dorado Interstate...............................          II        III       III       III        III
----------------------------------------------------------------------------------------------------------------

[37 FR 10869, May 31, 1972, as amended at 45 FR 9909, Feb. 14, 1980]



Secs. 52.972--52.974  [Reserved]



Sec. 52.975  Redesignations and maintenance plans; ozone.

    (a) Approval. The Louisiana Department of Environmental Quality 
(LDEQ) submitted redesignation requests and maintenance plans for the 
areas of Beauregard, Lafourche, and St. Mary Parishes on June 14, 1993. 
Redesignation requests and maintenance plans were submitted for the 
areas of Grant and Lafayette on May 25, 1993. The EPA deemed these 
requests complete on September 10, 1993. Several approvability issues 
existed, however. The LDEQ addressed these approvability issues in 
supplemental ozone redesignation requests and revised maintenance plans. 
These supplemental submittals were received for the areas of Beauregard, 
Grant, Lafayette, Lafourche, and St. Mary Parishes on March 27, 1995, 
December 12, 1994, October 21, 1994, November 18, 1994, and November 23, 
1994, respectively. The redesignation requests and maintenance plans 
meet the redesignation requirements in section 107(d)(3)(E) of the Act 
as amended in 1990. The redesignations meet the Federal requirements of 
section 182(a)(1) of the Clean Air Act as a revision to the Louisiana 
ozone State Implementation Plan for these areas. The EPA therefore 
approved the request for redesignation to attainment with respect to 
ozone for the areas of Beauregard, Grant, Lafayette, Lafourche, and St. 
Mary Parishes on October 17, 1995.
    (b) Approval--The Louisiana Department of Environmental Quality 
(LDEQ) submitted a redesignation request and maintenance plan for St. 
James Parish on May 25, 1993. The EPA deemed this request complete on 
September 10, 1993. Several approvability issues existed, however. The 
LDEQ addressed these approvability issues in a supplemental ozone 
redesignation request and revised maintenance plan. This supplemental 
submittal was received for St. James Parish on December 15, 1994. The 
redesignation request and maintenance plan meet the redesignation 
requirements in section 107(d)(3)(E) of the Act as amended in 1990. The 
redesignation meets the Federal requirements of section 182(a)(1) of the 
Clean Air Act as a revision to the Louisiana ozone State Implementation 
Plan for this parish. The EPA therefore approved the request for 
redesignation to attainment with respect to ozone for St. James Parish 
on November 13, 1995.
    (c) Approval--The Louisiana Department of Environmental Quality

[[Page 524]]

(LDEQ) submitted a redesignation request and maintenance plan for the 
New Orleans CMSA on April 23, 1993. The EPA deemed this request complete 
on September 10, 1993. Several approvability issues existed, however. 
The LDEQ addressed these approvability issues in a supplemental ozone 
redesignation request and revised maintenance plan. This supplemental 
submittal was received on October 14, 1994. The redesignation request 
and maintenance plans meet the redesignation requirements in section 
107(d)(3)(E) of the Act as amended in 1990. The redesignation meets the 
Federal requirements of section 182(a)(1) of the Clean Air Act as a 
revision to the Louisiana ozone State Implementation Plan for Jefferson, 
Orleans, St. Bernard, and St. Charles Parishes. The EPA therefore 
approved the request for redesignation to attainment with respect to 
ozone for 7Jefferson, Orleans, St. Bernard, and St. Charles Parishes on 
December 1, 1995.
    (d) Approval--The Louisiana Department of Environmental Quality 
submitted a redesignation request and maintenance plan for Pointe Coupee 
Parish on December 20, 1995. The redesignation request and maintenance 
plan meet the redesignation requirements in section 107(d)(3)(E) of the 
Act as amended in 1990. The redesignation meets the Federal requirements 
of section 182(a)(1) of the Clean Air Act as a revision to the Louisiana 
ozone State Implementation Plan for Pointe Coupee Parish. The EPA 
therefore approved the request for redesignation to attainment with 
respect to ozone for Pointe Coupee Parish on December 20, 1996.
    (e) Approval--The Louisiana Department of Environmental Quality 
submitted a redesignation request and maintenance plan for Calcasieu 
Parish on December 20, 1995. The redesignation request and maintenance 
plan meet the redesignation requirements in section 107(d)(3)(E) of the 
Act. The redesignation meets the Federal requirements of section 
182(a)(1) of the Act as a revision to the Louisiana ozone State 
Implementation Plan for Calcasieu Parish. The EPA therefore approved the 
request for redesignation to attainment with respect to ozone for 
Calcasieu Parish on June 2, 1997.
    (f) Lafourche Parish, Louisiana, is designated back to nonattainment 
for ozone. The original classification of incomplete data is retained.
[60 FR 43025, Aug. 18, 1995, as amended at 60 FR 47285, Sept. 12, 1995; 
60 FR 51360, Oct. 2, 1995; 62 FR 652, Jan. 6, 1997; 62 FR 24038, May 2, 
1997; 62 FR 64286, Dec. 5, 1997]



Sec. 52.976  Review of new sources and modification.

    (a) Section 6.7 of Regulation 6.0 is disappoved since it could 
conflict with the preconstruction requirements for the prevention of 
significant deterioration (PSD) of air quality.
    (b) Section 6.9 of Regulation 6.0 is disapproved since it could 
conflict with the preconstruction requirements for the prevention of 
significant deterioration (PSD) of air quality and the Administrator's 
Interpretative on Rule of December 21, 1976.
[44 FR 18491, Mar. 28, 1979, as amended at 47 FR 6017, Feb. 10, 1982]



Secs. 52.977--52.985  [Reserved]



Sec. 52.986  Significant deterioration of air quality.

    (a) The plan submitted by the Governor of Louisiana on August 14, 
1984 (as adopted by the Secretary of Louisiana Department of 
Environmental Quality (LDEQ) on May 23, 1985), July 26, 1988 (as revised 
and adopted by the LDEQ on May 5, 1988), and October 26, 1990 (as 
revised and adopted by the LDEQ on July 20, 1990), LAC:33:III: Sec. 509 
Prevention of Significant Deterioration (PSD) and its Supplement 
documents, is approved as meeting the requirements of Part C, Clean Air 
Act for preventing significant deterioration of air quality.
    (b) The requirements of Section 160 through 165 of the Clean Air Act 
are not met for Federally designated Indian lands since the plan 
(specifically LAC:33:III:509.A.1) excludes all Federally recognized 
Indian lands from the provisions of this regulation. Therefore, the 
provisions of Sec. 52.21 (b) through (w) are hereby incorporated by 
reference and made a part of the applicable implementation plan, and are 
applicable to sources located on land

[[Page 525]]

under the control of Indian governing bodies.
[56 FR 20139, May 2, 1991]



Sec. 52.987  Control of hydrocarbon emissions.

    (a) Notwithstanding any provisions to the contrary in the Louisiana 
Implementation Plan, the control measures listed in paragraphs (b) 
through (n) of this section shall be implemented in accordance with the 
schedule set forth below.
    (b) Removal from service of a 10,000 barrel capacity crude oil 
storage tank at the Belcher Station of the Exxon Pipeline Company, 
Belcher, Louisiana, with a final compliance date of January 1, 1980. 
This shall result in an estimated hydrocarbon emission reduction of at 
least 208 tons per year.
    (c) Removal from service of a 55,000 barrel capacity crude oil 
storage tank at the Weller Station of the Exxon Pipeline Company, near 
Minden, Louisiana, with a final compliance date of January 1, 1980. This 
shall result in an estimated hydrocarbon emission reduction of at least 
263 tons per year.
    (d) Installation of emission control systems on three 3,000 barrel 
capacity distillate storage tanks, at the Jones O'Brien Inc., Keatchie, 
Louisiana, with a final compliance date of January 1, 1978. This shall 
result in an estimated hydrocarbon emission reduction of at least 23 
tons per year.
    (e) Installation of emission control systems on crude oil storage 
tanks TK-43, TK-44, T-45 and T-49, and distillate tanks T-46 and T-50 at 
the Atlas Processing Company, Shreveport, Louisiana with a final 
compliance date of January 2, 1980. This shall result in an estimated 
hydrocarbon emission reduction of at least 881 tons per year.
    (f) Installation of emission control systems on crude oil storage 
tanks TK-19-74, TK-HC-74, TK-571-74 and TK-15-74 and agreement to store 
only nonvolatile organic solvent in tanks TK-F2-74, TK-41-74 and TK-40-
74 at the Cotton Valley Solvents Company, Cotton Valley, Louisiana with 
a final compliance date of January 2, 1980. This shall result in an 
estimated hydrocarbon emission reduction of at least 934 tons per year.
    (g) Discontinue use of residue gas in pneumatic instrumentation and 
control systems at the Kerr-McGee Corporation, Devon Corporation, and 
Eason Oil Company, Calhoun Plant, Calhoun, Louisiana with a final 
compliance date of July 1, 1978. This shall result in an estimated 
hydrocarbon emission reduction of at least 21 tons per year.
    (h) Discontinue use of residue gas in pneumatic instrumentation and 
control systems with a final compliance date of July 1, 1978, and 
install emission control systems on distillate storage tanks 2-7 and 2-
13 with a final compliance date of January 2, 1980, at the Kerr-McGee 
Corp., Devon Corp., and Eason Oil Co., Dubach Plant, Dubach, Louisiana. 
This shall result in an estimated hydrocarbon reduction of at least 367 
tons per year.
    (i) Installation of emission control systems on a 37,500 barrel 
capacity crude oil storage tank at Cities Service Pipeline Company, Oil 
City, Louisiana with a final compliance date of February 1, 1980. This 
shall result in an estimated hydrocarbon emission reduction of at least 
208 tons per year.
    (j) Installation of emission control systems on a 25,000 barrel 
capacity crude oil storage tank at Cities Service Pipeline Company, 
Haynesville, Louisiana with a final compliance date of February 1, 1980. 
This shall result in an estimated hydrocarbon emission reduction of at 
least 28 tons per year.
    (k) Installation of emission control systems on a 10,000 barrel 
capacity crude oil storage tank at Cities Service Pipeline Company, 
Summerfield, Louisiana with final compliance achieved in August 1977. 
This shall result in an estimated hydrocarbon emission reduction of at 
least 162 tons per year.
    (l) Installation of emission control systems on a 30,000 barrel 
capacity crude oil storage tank at the Scurlock Oil Company, Lake End, 
Louisiana, with a final compliance date of January 15, 1980. This shall 
result in an estimated hydrocarbon emission reduction of at least 90 
tons per year.
    (m) Installation of emission control systems on a 55,000 barrel 
capacity crude oil storage tank at the Scurlock Oil Company, Dutchtown 
Oil Field near

[[Page 526]]

Minden, Louisiana, with a final compliance date of January 15, 1980. 
This shall result in an estimated hydrocarbon emission reduction of at 
least 186 tons per year.
    (n) Installation of emission control systems on distillate storage 
tank No. 414 with a final compliance date of September 1, 1979, and the 
removal from service of tank No. 450 with final compliance achieved on 
December 1, 1977, at the Texas Eastern Products Pipeline Company, 
Sarepta, Louisiana. This shall result in an estimated hydrocarbon 
emission reduction of at least 355 tons per year.
[44 FR 15705, Mar. 15, 1979]



Sec. 52.988  [Reserved]



Sec. 52.990  Stack height regulations.

    The State of Louisiana has committed to submit to EPA a SIP revision 
whenever a new or revised emission limitation for a specific source 
exceeds the height allowed by Section 921(A) ``Good Engineering Practice 
(GEP) Stack Height 1 or 2'' of the State regulations. A letter from the 
Secretary of Louisiana Department of Environmental Quality, dated 
September 23, 1986, stated that:

    In specific, the State regulation, Section 17.14.2 [now LAC 33: Part 
III, Section 921(B)], provides that the degree of emission limitation 
required of any source for control of any air pollutant must not be 
affected by so much of any source's stack height that exceeds good 
engineering practice or by any other dispersion technique. In reference 
to this requirement, the Louisiana Department of Environmental Quality 
or the Administrative Authority will submit to EPA a SIP revision 
whenever the Louisiana Department of Environmental Quality adopts a new 
or revised emission limitation for a specific source that is based on a 
stack height that exceeds the height allowed by Section 17.14.1(e)(1) 
[now LAC 33: Part III, Section 921(A) ``Good Engineering Practice (GEP) 
Stack Height 1''] or Section 17.14.1(e)(2) [now LAC 33: Part III, 
Section 921(A) ``Good Engineering Practice (GEP) Stack Height 2''].
[53 FR 36010, Sept. 16, 1988]



Sec. 52.991  Small business assistance program.

    The Governor of Louisiana submitted on October 22, 1992, a plan 
revision to develop and implement a Small Business Stationary Source 
Technical and Environmental Compliance Assistance Program to meet the 
requirements of section 507 of the Clean Air Act by November 15, 1994. 
The plan commits to provide technical and compliance assistance to small 
businesses, hire an Ombudsman to serve as an independent advocate for 
small businesses, and establish a Compliance Advisory Panel to advise 
the program and report to EPA on the program's effectiveness.
[59 FR 32360, June 23, 1994]



Sec. 52.992  Area-wide nitrogen oxides exemptions.

    (a) The Louisiana Department of Environmental Quality submitted to 
the EPA on August 5, 1994, a petition requesting that the 
nonclassifiable ozone nonattainment areas in the State of Louisiana be 
exempted from the requirement to meet the NOX provisions of 
the Federal transportation conformity rule. The exemption request was 
based on monitoring data which demonstrated that the National Ambient 
Air Quality Standard for ozone had been attained in this area for the 3 
years prior to the petition. The parishes for which the NOX 
exemption was requested include: Beauregard, Grant, Lafayette, 
Lafourche, Jefferson, Orleans, St. Bernard, St. Charles, St. James, and 
St. Mary. The EPA approved this exemption request on March 2, 1995.
    (b) The LDEQ submitted to the EPA on November 17, 1994, a petition 
requesting that the Baton Rouge serious ozone nonattainment area be 
exempted from the NOX control requirements of the CAA. In 
addition, supplemental information was submitted to the EPA by the LDEQ 
on January 26, 1995, June 6, 1995, and June 16, 1995. The Baton Rouge 
nonattainment area consists of East Baton Rouge, West Baton Rouge, 
Pointe Coupee, Livingston, Iberville, and Ascension Parishes. The 
exemption request was based on photochemical grid modeling which shows 
that reductions in NOX would not contribute to attainment in 
the nonattainment area. On January 18, 1996, the EPA approved the 
State's request for an areawide exemption from the following 
requirements: NOX new source review, NOX

[[Page 527]]

reasonably available control technology, NOX general 
conformity, and NOX inspection and maintenance requirements.
    (c) The LDEQ submitted to the EPA on July 25, 1995, a revision to 
the SIP, pursuant to section 182(b)(1), requesting that the Baton Rouge 
serious ozone nonattainment area be exempted from the transportation 
conformity NOX requirements of the CAA. The Baton Rouge 
nonattainment area consists of East Baton Rouge, West Baton Rouge, 
Pointe Coupee, Livingston, Iberville, and Ascension Parishes. The 
exemption request was based on photochemical grid modeling which shows 
that additional reductions in NOX would not contribute to 
attainment in the nonattainment area. On February 12, 1996, the EPA 
approved the State's request for an areawide exemption from the 
transportation conformity NOX requirements.
    (d) The LDEQ submitted to the EPA on October 28, 1994, a petition 
requesting that the Lake Charles marginal ozone nonattainment area be 
exempted from the NOX control requirements of the Act. The 
Lake Charles nonattainment area consists of Calcasieu Parish. The 
exemption request was based on photochemical grid modeling which shows 
that reductions in NOX would not contribute to attainment in 
the nonattainment area. On May 27, 1997, the EPA approved the State's 
request for an area-wide exemption from the following requirements: 
NOX new source review, NOX general conformity, and 
NOX transportation conformity requirements. The waiver was 
granted on the basis of modeling, and ambient air quality data 
demonstrating the area has attained the ozone NAAQS.
[60 FR 5864, Jan. 31, 1995, as amended at 61 FR 2446, Jan. 26, 1996; 61 
FR 7221, Feb. 27, 1996; 62 FR 29078, May 29, 1997]



Sec. 52.993  Emissions inventories.

    (a) The Governor of the State of Louisiana submitted the 1990 base 
year emission inventories for the Baton Rouge (BTR) and Calcasieu Parish 
(CAL) ozone nonattainment areas on November 16, 1992 as a revision to 
the State Implementation Plan (SIP). The 1990 base year emission 
inventory requirement of section 182(a)(1) of the Clean Air Act, as 
amended in 1990, has been satisfied for each of these areas.
    (b) The inventories are for the ozone precursors which are volatile 
organic compounds, nitrogen oxides, and carbon monoxide. The inventories 
cover point, area, non-road mobile, on-road mobile, and biogenic 
sources.
    (c) The BTR nonattainment area is classified as Serious and includes 
Ascension, East Baton Rouge, Iberville, Livingston, Point Coupee, and 
West Baton Rouge Parishes; the CAL nonattainment area is classified as 
Marginal and includes Calcasieu Parish.
[60 FR 13911, Mar. 15, 1995]



Sec. 52.994  [Reserved]



Sec. 52.995  Enhanced ambient air quality monitoring.

    (a) The Governor of the State of Louisiana submitted the 
photochemical assessment monitoring stations (PAMS) State Implementation 
Plan (SIP) revision for the Baton Rouge ozone nonattainment area on 
September 10, 1993. This SIP submittal satisfies 40 CFR 58.20(f), which 
requires the State to provide for the establishment and maintenance of 
PAMS.
    (b) The Baton Rouge ozone nonattainment area is classified as 
Serious and includes Ascension, East Baton Rouge, Iberville, Livingston, 
Pointe Coupee, and West Baton Rouge Parishes.
[61 FR 31037, June 19, 1996]



Sec. 52.996  Disapprovals.

     The State of Louisiana motor vehicle Inspection and Maintenance (I/
M) program SIP submittal of August 18, 1995, with later editions, is 
disapproved based on the failure of the State Legislature to grant legal 
authority to reauthorize and continuously operate the program until the 
program is no longer necessary. The Baton Rouge serious ozone 
nonattainment area is required to have an enhanced I/M program under 
section 182 of the Clean Air Act (the Act) as amended in 1990. This 
disapproval initiates the sanction process of section 179(a) of the Act.
[62 FR 61634, Nov. 19, 1997; 63 FR 4397, Jan. 29, 1998]
[[Page 529]]


                              FINDING AIDS






  --------------------------------------------------------------------

  A list of CFR titles, subtitles, chapters, subchapters and parts and 
an alphabetical list of agencies publishing in the CFR are included in 
the CFR Index and Finding Aids volume to the Code of Federal Regulations 
which is published separately and revised annually.
  Material Approved for Incorporation by Reference
  Table of CFR Titles and Chapters
  Alphabetical List of Agencies Appearing in the CFR
  Table of OMB Control Numbers
  List of CFR Sections Affected

[[Page 531]]

            Material Approved for Incorporation by Reference

                      (Revised as of July 1, 1998)

  The Director of the Federal Register has approved under 5 U.S.C. 
552(a) and 1 CFR Part 51 the incorporation by reference of the following 
publications. This list contains only those incorporations by reference 
effective as of the revision date of this volume. Incorporations by 
reference found within a regulation are effective upon the effective 
date of that regulation. For more information on incorporation by 
reference, see the preliminary pages of this volume.


40 CFR (52.01 TO 52.1018)

ENVIRONMENTAL PROTECTION AGENCY
                                                                  40 CFR


Environmental Protection Agency

  Office of Air Quality Planning and Standards, 
  Research Triangle Park, NC 27711
  State Implementation Plans: Consisting of 
  Original State Implementation Plans for the 
  fifty States and the territories of Guam; Puerto 
  Rico, Virgin Islands and American Samoa; 
  Regulatory and Non-Regulatory Revisions to State 
  Implementation Plans approved 1972-June 1979 
  (prepared by Atlantic Environmental Associates, 
  Inc.); and Individual State Implementation Plan 
  Revisions, which are identified below by State 
  and date of publication of the Federal Register 
  rule.
  Alabama: Nov. 26, 1979; June 3, Aug. 11, Oct. 
  31, 1980; Apr. 27, Aug. 24, Sept. 17, Oct. 29, 
  Nov. 6, Nov. 10, Nov. 24, Dec. 15, Dec. 22, Dec. 
  30, 1981; Feb. 22, 1982; Mar. 9, 1983; Apr. 19, 
  1984; Aug. 28, 1985; Feb. 10, July 11, July 14, 
  Dec. 19, Dec. 24, 1986; Feb. 11, July 29, 1987; 
  Nov. 25, 1988; Jan. 23, Mar. 19, Apr. 25, Sept. 
  24, Sept. 27, 1990; July 17, 1991; June 9, 1992; 
  Apr. 27, Aug. 30, Sept. 27, 1993; Feb. 4, Aug. 
  4, Oct. 20, Oct. 31, 1994; Jan. 6, 1995; Feb. 6, 
  Feb 12, Mar. 19, 1996; June 6, 1997
  Alaska: Dec. 30, 1980; Apr. 15, 1981; July 5, 
  1983; Jan. 3, Apr. 24, 1984; Sept. 15, 1986; 
  Mar. 1, May 26, July 31, 1989; Apr. 26, 1991; 
  Aug. 13, 1993; Mar. 24, 1994; Feb. 16, Apr. 5, 
  June 29, Sept. 5, Sept. 27, Oct. 24, 1995; May 
  16, 1996; Mar. 11, 1998
  Arizona: Dec. 17, 1979; Aug. 11, Oct. 10, 1980; 
  Aug. 10, Sept. 14, Sept. 18, 1981; Apr. 12, Apr. 
  16, May 5, June 18, June 30, Sept. 28, 1982; 
  Jan. 14, May 3, 1983; Oct. 19, 1984; Aug. 10, 
  1988 (2 amendments); Jan. 29, 1991; Jan. 6, Mar. 
  9, 1992; Nov. 1, 1994; Apr. 10 (2 amendments), 
  May 2, May 8, June 15, Sept. 5, 1995; Feb. 12, 
  Apr. 9, Oct. 3, 1996; Mar. 17, June 11, Aug. 4, 
  1997; Feb. 9 (2 amendments), Feb. 10, Mar. 31, 
  May 4, 1998
  Arkansas: Jan. 29, Aug. 15, 1980; Aug. 6, Aug. 
  27 (2 amendments), Oct. 13, 1981; Jan. 12, Jan. 
  14 (2 amendments), Apr. 16, May 3, May 4, 1982; 
  Feb. 8, 1983; Feb. 10, Aug. 4, Nov. 12, 1986; 
  July 21, 1988; Feb. 23, May 1, 1989; May 2, 
  1991; Mar. 8, 1995; Apr. 10, 1998

[[Page 532]]

  California: July 30, Dec. 6, 1979; Apr. 24 (2 
  amendments), May 9, May 28 (2 amendments), June 
  3, June 4, Aug. 11 (2 amendments), Sept. 26, 
  Oct. 24, Oct. 31, Nov. 10, Dec. 4, 1980; Jan. 
  16, Jan. 21, Jan. 27, Apr. 14, May 18 (2 
  amendments), Aug. 10, Aug. 21, Sept. 2, Sept. 
  28, Dec. 9, 1981; Jan. 22, Jan. 25, Jan. 26 (2 
  amendments), Mar. 10, Mar. 19, Mar. 29, Apr. 4, 
  Apr. 12, Apr. 13, Apr. 23, May 3, May 7, May 27, 
  June 9, June 18 (2 amendments), June 21, June 
  23, June 30, July 1, July 6, July 7, July 8, 
  Nov. 10, Dec. 14, 1982; June 1, Oct. 11, Nov. 
  16, Nov. 18 (2 amendments), Nov. 22, Nov. 25, 
  Nov. 28, Dec. 28, 1983; Feb. 1, Feb. 24, Feb. 
  28, Apr. 19, May 3 (3 amendments), July 12, July 
  30, Oct. 3, Oct. 19, Dec. 5, 1984; Jan. 24, Jan. 
  29, May 9, June 19, July 31, Aug. 9, Sept. 4, 
  1985; Jan. 7, 1986; Jan. 15, Feb. 3, Apr. 17, 
  July 13, 1987; Feb. 3, Apr. 10, Apr. 12, Apr. 
  17, Oct. 23, 1989 (2 amendments); July 12 (2 
  amendments), Aug. 6 (2 amendments), Nov. 7, 
  1990; Apr. 16, Aug. 20, 1991; Mar. 24, Apr. 24, 
  June 10, Aug. 11, Oct. 26, 1992; Mar. 22, May 13 
  (3 amendments), June 16 (2 amendments), June 30 
  (2 amendments), July 12, Aug. 30 (4 amendments), 
  Sept. 13, Sept. 29, Dec. 6, Dec. 20, 1993 (5 
  amendments); Jan. 18, Feb. 8, Apr. 6, Apr. 14, 
  June 9, June 23, Aug. 4, Aug. 16, Aug. 17, Aug. 
  25, Aug. 29 (2 amendments), Sept. 16, Oct. 4, 
  Dec. 1, Dec. 9, Dec. 13 (3 amendments), Dec. 14 
  (3 amendments), 1994; Jan. 6, Jan. 24, Jan. 30, 
  Feb. 15, Feb. 16 (3 amendments), Mar. 6, Mar. 22 
  (3 amendments), Mar. 23, Apr. 3, Apr. 13, Apr. 
  26, May 2, May 3, May 22, May 23, June 13, June 
  23 (2 amendments), July 13, July 14, Aug. 8, 
  Aug. 18, Aug. 21 (2 amendments), Aug. 23, Sept. 
  6, Sept. 7 (2 amendments), Sept. 12, Sept. 26, 
  Sept. 27, Oct. 23, Oct. 25, Dec. 14, 1995; Feb. 
  1, Feb. 9 (3 amendments), Feb. 12, Feb. 13, Feb. 
  14, Feb. 29, Mar. 1, Apr. 9, Apr. 26, Apr. 30 (2 
  amendments), May 2, May 6 (2 amendments), May 7, 
  June 12, June 24, July 11, July 18, July 25, 
  Aug. 27, Aug. 28, Oct. 7, Oct. 23, Nov. 1 (2 
  amendments), Nov. 4, Nov. 8, Nov. 13, Dec. 4, 
  1996; Jan. 8 (2 amendments), Jan. 17, Jan. 22 (2 
  amendments), Feb. 24, Mar. 27, Apr. 17, Apr. 30, 
  May 6, June 17, July 7, July 11, Aug. 4, Aug. 
  25, Sept. 16, Oct. 15, Oct. 21, Oct. 23, Nov. 1, 
  Nov. 3, Nov. 13, Nov. 26, Dec. 15, Dec. 23, 
  1997; Feb. 6, Feb. 18, Mar. 11, Mar. 20, Mar. 
  31, Apr. 21 (2 amendments), June 15, June 22, 
  1998
  Colorado: Oct. 5, 1979; July 9, July 16, Aug. 1, 
  1980; Mar. 13, Mar. 19, Apr. 30, Nov. 30, Dec. 
  7, 1981; Jan. 29, Sept. 28, 1982; Dec. 12, 1983; 
  June 28, Dec. 18, 1985; Apr. 10, Sept. 2, Dec. 
  3, 1986; June 22, 1987; July 25, Aug. 12 (2 
  amendments), Sept. 30, Dec. 1, 1988; Mar. 8, 
  Mar. 31, May 11, May 30, June 7, 1989; Mar. 12, 
  1990; Mar. 28, Apr. 17, 1991; June 17, June 24, 
  June 26, Nov. 19, 1992; Sept. 27, 1993; May 19, 
  July 8, Aug. 18, Sept. 14, Sept. 19, Oct. 11, 
  Nov. 8, Dec. 14, 1994; May 30, 1995; Mar. 19, 
  Sept. 23, Oct. 4, Nov. 29, 1996; Jan. 16, Jan. 
  17, Jan. 21, Jan. 30, Mar. 10, Mar. 20, Apr. 17, 
  Dec. 23, Dec. 31, 1997; Mar. 25, Mar. 31, 1998

[[Page 533]]

  Connecticut: July 30, 1979; Dec. 23, 1980; Apr. 
  27, May 14, July 7, Aug. 28 (2 amendments), Oct. 
  23, Nov. 18, Dec. 22, 1981; Jan. 7, Feb. 17, 
  June 7, Aug. 24, Sept. 23, Nov. 12, 1982; Feb. 
  8, May 4, June 28, Dec. 20, 1983; Jan. 25, Feb. 
  1, Mar. 21, Oct. 19, 1984; July 18, Dec. 13, 
  1985; Nov. 20, 1986; Feb. 19, Dec. 17, 1987; 
  Feb. 17, Apr. 11, May 19, July 12, Aug. 1, 1988; 
  Mar. 8, Mar. 24, Apr. 10, May 30, June 2, Nov. 
  28, Nov. 30, Dec. 22, 1989; Mar. 12, 1990; Mar. 
  24, Nov. 20, 1992; Feb. 23, Dec. 17, 1993; Jan. 
  18, May 19, 1994; Jan. 10, Sept. 11, Oct. 31, 
  1995; July 25, 1996; Mar. 26, Oct. 6, Oct. 24, 
  1997; Feb. 9, Apr. 24, 1998
  Delaware: July 30, 1979; Mar. 6, Aug. 1, 1980; 
  May 15, Aug. 25, Sept. 28, Sept. 30, Oct. 30, 
  1981; Feb. 8, 1982; Jan. 26, Sept. 21, Oct. 17, 
  1983; Oct. 3, 1984; July 2, 1985; Dec. 8, 1986; 
  Dec. 28, 1987; Jan. 22, Feb. 1, June 29, 1990; 
  Mar. 29, 1991; Jan. 6, Nov. 12, 1992; July 27, 
  1993; Apr. 6, 1994; May 3 (2 amendments), July 
  28, 1995; Jan. 26, Feb. 28, Mar. 26, 1996; Mar. 
  12, May 14, July 15, 1997
  District of Columbia: Jan. 4, Mar. 3, 1980; Jan. 
  30, Aug. 3, Dec. 16, 1981; Aug. 18, 1983; June 
  1, Oct. 3, 1984; Apr. 10, 1986; Aug. 4, 1992; 
  Jan. 26, May 2 (2 amendments), May 26, Aug. 28, 
  1995; Jan. 30, 1996
  Florida: Feb. 29, Mar. 18, Sept. 10, Nov. 14, 
  Dec. 16, 1980; Mar. 17, May 14, July 15, Aug. 
  25, Sept. 25, Oct. 28, Nov. 13, Nov. 24 (2 
  amendments), Dec. 15, Dec. 16, Dec. 22, 1981; 
  Jan. 22, Mar. 3, Apr. 12, Apr. 13, May 10, June 
  18, July 7, July 26 (2 amendments), Aug. 16, 
  Oct. 26, 1982; Mar. 14, May 2, July 25, July 26, 
  Sept. 15, Nov. 17, Nov. 22, 1983; Feb. 2, 1984; 
  Nov. 1, Dec. 23, Dec. 24, 1985; Jan. 21, 1986; 
  Sept. 23, 1987; Mar. 29, June 30, 1988; Feb. 8, 
  July 25, 1989; Feb. 1, Apr. 6, Nov. 7, 1990; 
  Oct. 17, 1991; Mar. 3, June 9, 1992 (2 
  amendments); Mar. 22, July 13, 1993; Feb. 23, 
  Mar. 24, Apr. 14, Sept. 6, Sept. 7, Sept. 9, 
  Oct. 11, Oct. 20, 1994; Jan. 3, Jan. 11, Feb. 
  14, Feb. 24, Dec. 7, 1995; Feb. 21, Apr. 25, 
  Sept. 18, Dec. 16, 1996; Jan. 17, July 21, 1997; 
  May 27, 1998
  Georgia: Sept. 18, 1979; Jan. 3, Jan. 24, 1980; 
  Mar. 20, May 5, May 22, Aug. 6, Aug. 14, Aug. 
  17, Nov. 13, Nov. 15, Nov. 24, 1981; Feb. 10, 
  Apr. 13, 1982; Nov. 10, 1983; Jan. 7, 1985; Jan. 
  28, 1986; July 6, July 12, Aug. 9, 1988; June 9, 
  Oct. 13, Dec. 14, 1992; Jan. 26, 1993; Mar. 8, 
  Aug. 30, Dec. 21, 1995; Feb. 2, June 27, Aug. 
  11, 1996
  Hawaii: Aug. 7, 1979; Aug. 10, 1981; Jan. 22, 
  Sept. 30, 1982; May 19, Aug. 18, 1983
  Idaho: July 30, 1979; Oct. 23, 1980; Mar. 4, 
  1981; July 28, 1982; May 3, 1984; June 6, 1985; 
  June 23, 1986; Dec. 1, 1988; July 23, 1993; Aug. 
  25, Sept. 19, Dec. 1, 1994; May 26, 1995; May 
  30, 1996

[[Page 534]]

  Illinois: Dec. 6, 1979; Jan. 3, Feb. 21, Sept. 
  22, Oct. 24, 1980; Jan. 27, Mar. 4, Sept. 3, 
  Oct. 21, Nov. 16, Nov. 27, 1981; Mar. 22, Mar. 
  30, May 24, June 9, June 21, Sept. 8, Oct. 29, 
  1982; July 6, Oct. 4, Oct. 11, 1983; Feb. 22 (2 
  amendments), Mar. 27, July 24, Aug. 7, Aug. 8, 
  1984 (2 amendments); Feb. 7, Sept. 25, Nov. 6, 
  1985; Mar. 31, Apr. 25 (2 amendments), June 4, 
  Nov. 24, 1986; Jan. 14, Jan. 21, Mar. 16, May 5, 
  Nov. 27, 1987; Feb. 12, 1988; Apr. 18, June 29, 
  July 18, Oct. 4, 1990; Mar. 24, June 26, Aug. 
  18, Sept. 2, Sept. 3, Dec. 17, Dec. 29, 1992; 
  Apr. 6, Aug. 30, Sept. 15, Oct. 21, 1993; Jan. 
  28, Aug. 4, Sept. 9, Nov. 18, 1994; Jan. 27, 
  Mar. 23, Apr. 3 (2 amendments), Apr. 5, May 3, 
  July 13 (2 amendments), Sept. 27 (2 amendments), 
  Oct. 26 (2 amendments), Nov. 8, 1995; Jan. 26, 
  Feb. 13, Mar. 19, Mar. 21, Mar. 25, Apr. 2, Apr. 
  9, May 7, July 25 (2 amendments), Aug. 8, Oct. 
  21, Dec. 23, 1996; Jan. 21, Mar. 12, June 9, 
  June 17, Aug. 12, Nov. 26, Dec. 23, 1997; Feb. 
  23, Mar. 11 (2 amendments), Mar. 23, May 19, 
  1998
  Indiana: Jan. 2, May 19, Aug. 6, Sept. 4, Nov. 
  5, Nov. 27, 1981; Feb. 3, Feb. 16, Mar. 12, May 
  13, June 22, July 16, Sept. 29, Oct. 27, Nov. 
  12, 1982; Jan. 18, May 18 (2 amendments), Dec. 
  6, Dec. 16, 1983; Feb. 14, Mar. 13, Mar. 23, 
  Apr. 3, Oct. 29, 1984; Apr. 17, May 1, May 17, 
  May 22, 1985; Feb. 10, Feb. 14, Apr. 25, June 3, 
  Nov. 24, 1986; Feb. 18, Apr. 20, June 17, Sept. 
  4, Dec. 10, 1987; Jan. 19, Apr. 19, Sept. 1, 
  Oct. 3, Nov. 18, Dec. 16, 1988; Jan. 19, Aug. 
  17, Nov. 6, 1989; May 3, July 31, Aug. 22, Sept. 
  6, Sept. 25, 1990; Mar. 6, Sept. 17, 1992; June 
  16, Aug. 13, 1993; Apr. 28, June 20, Aug. 18, 
  Oct. 17, 1994; Mar. 8, May 3, May 4 (2 
  amendments), June 15, July 5, Aug. 18, 1995; 
  Feb. 1, Feb. 9 (2 amendments), Mar. 19, Mar. 21, 
  Apr. 2, Apr. 9, June 13 (2 amendments), Oct. 30, 
  1996; Jan. 17 (2 amendments), Jan. 22, Feb. 18, 
  Apr. 3, Apr. 16, Apr. 18, May 7, June 3, July 
  21, 1997; Jan. 14, June 29, July 1, 1998
  Iowa: Mar. 6, 1980, Mar. 20, Apr. 17, Oct. 21, 
  Dec. 8, 1981; Jan. 11, Mar. 5, Apr. 12 (2 
  amendments), May 25, 1982; Sept. 12, 1985; July 
  11, 1986; June 26, 1987; Oct. 24, 1988; July 17, 
  Aug. 15, 1989 (3 amendments); June 29, 1990; 
  Nov. 1, Nov. 29, 1991; Jan. 22, 1992; Jan. 26, 
  May 12, Sept. 27, 1993; Dec. 21, 1994; June 13, 
  Oct. 30 (2 amendments), 1995; Mar. 30, Apr. 30, 
  1996; Oct. 23, Dec. 1, 1997; Feb. 2, June 25, 
  1998
  Kansas: Apr. 3, Oct. 22, Dec. 15, 1981; Jan. 22, 
  June 18, 1982; Jan. 12, Dec. 11, 1984; July 11, 
  1986; Jan. 2, Dec. 21, 1987; May 18, Aug. 22, 
  Oct. 28, Nov. 25, 1988; Apr. 20, July 17, Oct. 
  27, 1989; Jan. 16, 1990; June 23, 1992; Jan. 12, 
  1993; May 12, Oct. 18, 1994; July 17, 1995; Apr. 
  25, Oct. 2, 1996; July 7, 1997

[[Page 535]]

  Kentucky: Jan. 25, Oct. 31, Dec. 24, 1980; June 
  15, Aug. 7 (2 amendments), Sept. 14, Oct. 29 (2 
  amendments), Nov. 16, Nov. 20, Nov. 24, Nov. 30, 
  1981 (2 amendments); Jan. 12, Mar. 8, Apr. 13, 
  May 11, June 9, July 12, Aug. 10, 1982; Mar. 22, 
  Apr. 19, May 2, May 5, 1983; Jan. 11, Mar. 23, 
  May 3, Oct. 9, 1984; Apr. 18, 1985; Dec. 4, 
  1986; Feb. 2, Sept. 4, Dec. 3, 1987; Jan. 8, 
  Apr. 8, June 21, July 12, Aug. 17, 1988; Feb. 24 
  (2 amendments), Apr. 20, Apr. 27, May 4, Aug. 
  25, Sept. 1, Nov. 6, Nov. 9, Nov. 13, Nov. 28, 
  1989; Feb. 2, Feb. 7, May 16, 1990; Oct. 22, 
  1993; June 23, Nov. 3, 1994; Feb. 7, May 2, May 
  24, June 13, June 19, June 29, July 28, Sept. 
  11, Sept. 27, 1995; Mar. 3, Apr. 2, June 28, 
  1996; Jan. 21, 1997; Jan. 13, 1998
  Louisiana: Feb. 14, 1980; Aug. 6, Oct. 29, 1981; 
  Feb. 10, Feb. 16, Apr. 14 (2 amendments), May 
  10, June 9, July 7, July 28, 1982; May 1, May 3, 
  May 18, 1984; Apr. 16, 1986; Apr. 24, 1987; 
  Sept. 16, Dec. 19, 1988; Mar. 8, Mar. 24, June 
  15, June 27, Oct. 10, Nov. 27, 1989; Feb. 2, 
  July 18, Sept. 7, 1990; May 2, 1991; Mar. 6, 
  1992; July 15, 1993; Mar. 25, May 5, June 23, 
  Oct. 4, 1994; Jan. 6, Oct. 23, 1995; July 22, 
  July 25, Sept. 13, Sept. 25, Oct. 15, Oct. 22, 
  Oct. 30, 1996; Jan. 6, May 2, Oct. 2, Oct. 10, 
  Dec. 2, 1997; Mar. 9, May 11, 1998
  Maine: Jan. 30, Feb. 19, Sept. 9, Dec. 9, 1980; 
  Jan. 5, Jan. 22, Aug. 25, 1981; Jan. 8, Feb. 17, 
  Mar. 5, 1982; May 13, 1983; Feb. 26, May 1, 
  1985; Mar. 21, 1989; May 18, 1990; Feb. 3, 1992, 
  Mar. 22, Mar. 23, June 21, 1993; Mar. 18, June 
  17, Nov. 3, 1994; Jan. 10, Jan. 12, June 29, 
  Aug. 30, Sept. 12, Dec. 26, 1995; Feb. 14, Oct. 
  15, 1996; Sept. 23, 1997
  Maryland: Dec. 6, 1979; Mar. 18, Apr. 17, Apr. 
  25, July 3, Aug. 12, Aug. 19, Sept. 3, Sept. 4, 
  1980; Mar. 18, July 31, Aug. 18, Sept. 4, Sept. 
  8, Sept. 11 (4 amendments), Oct. 8, Oct. 9, Nov. 
  16, Dec. 16, Dec. 29, 1981; Feb. 23, Apr. 8, May 
  10, June 18, July 7, 1982; Jan. 27, Mar. 27, 
  Apr. 8, Aug. 24, 1983; Mar. 8, Sept. 10, Sept. 
  19, Dec. 7, Dec. 20, 1984; Feb. 25, Feb. 26, 
  June 25, July 2, 1985; Aug. 4, 1986; Jan. 14, 
  May 30, 1989; May 16, 1990; May 24, 1991; June 
  24, Nov. 3, 1992; Apr. 7, May 18, July 27, Nov. 
  30, 1993; Jan. 18, Feb. 24, Apr. 4, June 9, June 
  10, Sept. 7 (2 amendments), Oct. 12, Nov. 29, 
  1994; Jan. 6, Oct. 23, 1995; Feb. 28, 1996; Feb. 
  25, Aug. 4, Sept. 2, Oct. 15, 1997; May 13, 1998
  Massachusetts: May 21, July 16, 1979; Jan. 10, 
  May 28, June 17, Aug. 12, Sept. 10 (2 
  amendments), Sept. 16, Dec. 15, 1980; Jan. 19, 
  Jan. 27, Mar. 4, Mar. 19, Aug. 11, Aug. 27, 
  Sept. 3, Sept. 17, Sept. 28, Dec. 15, 1981 (2 
  amendments); Jan. 25, Feb. 10, Mar. 8, Mar. 29, 
  Apr. 13, June 2, June 9, July 12, Nov. 23, Dec. 
  1, 1982; Apr. 28, July 7 (2 amendments), July 
  20, Nov. 9, 1983; Jan. 10, Mar. 8, Mar. 23 (2 
  amendments), July 30, Sept. 25 (2 amendments), 
  Oct. 30, 1984; Sept. 25, 1985; Apr. 1, Aug. 12, 
  Nov. 25, 1986 (2 amendments); Aug. 31, Nov. 19, 
  1987; Mar. 6, Mar. 10, May 4, Nov. 3, Nov. 8, 
  1989 (2 amendments); Feb. 15, Feb. 21, Apr. 19, 
  Aug. 3 (2 amendments), Aug. 27, 1990; Feb. 27, 
  Oct. 8, 1991; Oct. 8 (2 amendments), Dec. 14 (2 
  amendments), 1992, Jan. 11, Feb. 23, Mar. 16, 
  June 30, Sept. 15, 1993; Aug. 4, Oct. 4, 1994; 
  Jan. 6, Feb. 1, Mar. 6, Apr. 5, Aug. 15, Dec. 
  19, 1995; Jan. 30, Feb. 14, Mar. 21, Aug. 8, 
  Aug. 27, Oct. 15, 1996; July 14, 1997

[[Page 536]]

  Michigan: May 6, June 2, Aug. 11, Aug. 25, Dec. 
  17, Dec. 29, 1980; Jan. 27, Mar. 4, Apr. 17, May 
  1, May 14, May 22, June 5, July 2, Aug. 28, Nov. 
  27, Dec. 3, 1981; Jan. 12, Jan. 27 (2 
  amendments), Feb. 10, Feb. 17, Feb. 22, Mar. 24, 
  Apr. 13, May 19, July 26, Aug. 25, Oct. 14, Nov. 
  15 (2 amendments), Dec. 13, 1982; Mar. 4, July 
  5, July 6, July 7, Aug. 15, Sept. 15, 1983; Feb. 
  13, May 18, 1984 (2 amendments); May 1, Aug. 20, 
  Dec. 13, 1985; Nov. 24, 1986; Jan. 12, May 4, 
  1987; Feb. 17, Aug. 22, Nov. 2, 1988; Mar. 7, 
  Oct. 3, 1989; June 11, 1992; May 13, 1993; Mar. 
  8, June 3, Sept. 7, Sept. 15, Oct. 11, 1994; 
  Jan. 17, Mar. 7, Oct. 23, 1995; Feb. 21, Mar. 1, 
  June 21, Aug. 30, 1996; May 5, Nov. 6, 1997; 
  Feb. 10, 1998
  Minnesota: Dec. 13, 1979; June 16, 1980; Mar. 4, 
  Apr. 8, Nov. 27, Dec. 8, 1981; May 6, June 21, 
  1982; July 5, 1984; Dec. 31, 1986; Oct. 8, 1992; 
  Mar. 23, June 28, 1993; Feb. 15, Mar. 3, Mar. 
  16, Apr. 14 (3 amendments), Apr. 28, Sept. 9, 
  Oct. 4, Oct. 13, Oct. 18, Dec. 8, 1994; Jan. 18, 
  May 2, May 24, May 31, June 13, 1995; Feb. 21, 
  1996; Apr. 9, Apr. 23, Oct. 14, 1997
  Mississippi: Jan. 10, July 10, 1980; Aug. 11, 
  Oct. 5, 1982; Mar. 23, July 27, 1984; Jan. 3, 
  Mar. 20, 1986; Sept 23, 1987; Nov. 13, 1989; 
  Oct. 15, 1990; Aug. 4, 1992; Mar. 18, 1994; May 
  2, May 5, 1995; Feb. 12, 1996; July 1, 1997
  Missouri: Mar. 18, Apr. 9, May 9, June 16, Oct. 
  31, Dec. 24, 1980; Mar. 16, Apr. 3, Apr. 27, May 
  22, June 12, Aug. 27, Sept. 10, Oct. 28, Nov. 4, 
  Nov. 10, Nov. 13, Dec. 15, 1981; June 10, June 
  22, July 6, Aug. 30, 1982; July 21, 1983; June 
  1, June 11, Aug. 31, Sept. 27, Oct. 15, Nov. 14, 
  1984; Jan. 7, Jan. 24, Apr. 16, Aug. 12, Oct. 
  10, 1985; Feb. 10, Apr. 17, Aug. 22, Sept. 3, 
  Oct. 8, Nov. 6, 1986; Feb. 17, Apr. 14, Aug. 18, 
  Sept. 15, 1988; Mar. 13, Mar. 31, Apr. 20, July 
  31, Nov. 2, 1989; Jan. 9, Mar. 5, Nov. 2, 1990; 
  Feb. 2, Mar. 5, Apr. 17, July 23, 1991; Mar. 6, 
  June 23, Oct. 13, Nov. 5, 1992; Aug. 30, Oct. 
  26, 1993; May 12, Aug. 24, Sept. 6, 1994; May 5, 
  Aug. 4, Sept. 25, 1995; Feb. 6, Feb. 29 (2 
  amendments), Mar. 11, Mar. 28, Apr. 25, July 29, 
  1996; Mar. 5, May 14 (2 amendments), Aug. 20, 
  Aug. 26 (2 amendments), Sept. 5, Oct. 9, 1997; 
  Jan. 21, Apr. 22, Apr. 24, 1998
  Montana: Sept. 6, 1979; Jan. 10, Mar. 4, 1980; 
  Mar. 3, 1981; July 15, 1982; May 5, 1983; May 1, 
  July 9, July 13, 1984; Apr. 26, 1985; Jan. 16, 
  June 6, 1986; Dec. 2, 1988; Jan. 26, June 7, 
  1989; June 29, Sept. 7, 1990; May 24, 1991; Jan. 
  21, Dec. 6, Dec. 17, 1993; Jan. 18, Jan. 20, 
  Mar. 11, Apr. 14, Aug. 30, Nov. 8, Dec. 13, 
  1994; Jan. 27, Mar. 22, July 18, Aug. 30, Nov. 
  3, 1995; Mar. 19, Sept. 30, Oct. 23, Nov. 29, 
  1996
  Nebraska: Oct. 6, 1981; Jan. 22, May 5, 1982; 
  Mar. 28 (2 amendments), July 5, Nov. 29, 1983; 
  July 23, 1984; Jan. 31, May 30, 1985; Sept. 15, 
  Sept. 19, 1986; Aug. 3, 1987; Feb. 16, May 16, 
  1989; July 2, Oct. 7, 1991; Aug. 30, 1993; Jan. 
  4, 1995; Feb. 9, Feb. 12, Feb. 14, 1996; Mar. 
  20, 1997
  Nevada: Feb. 4, Feb. 6, July 10, 1980; Apr. 14, 
  Aug. 10, Aug. 27, Sept. 14, 1981; Mar. 8, Apr. 
  13 (2 amendments), June 18, June 21, June 23 (2 
  amendments), June 30, 1982; Feb. 10, 1983; Feb. 
  24, Mar. 20, Mar. 27, June 29, Aug. 8, Nov. 5, 
  1984; Aug. 21, 1986; Feb. 9, 1996

[[Page 537]]

  New Hampshire: Apr. 11, June 23, Sept. 9, Sept. 
  22, Dec. 18, 1980; July 15, 1981; Jan. 7, June 
  7, Dec. 17, Dec. 30, 1982; Mar. 15, Apr. 21, 
  June 27, Oct. 20, Oct. 31, 1983; Feb. 1, Mar. 
  23, Aug. 1, Aug. 7, Sept. 27, 1984 (2 
  amendments); Mar. 13, 1985; Feb. 2, Sept. 17, 
  Dec. 14, 1987; Aug. 25, 1988; June 13, Aug. 14, 
  Dec. 12, 1991; Aug. 14, 1992; Jan. 19, May 25, 
  1993; Aug. 19, Oct. 4, Oct. 12, 1994; Sept. 12, 
  1995; Apr. 9, Oct. 27, 1997; Mar. 10, May 13, 
  1998
  New Jersey: Mar. 11, Apr. 19, May 7, Oct. 31, 
  1980; Apr. 15, Apr. 27, May 12, Sept. 30, Nov. 
  3, 1981; June 11, 1982; July 8, Nov. 9, 1983; 
  Jan. 27, Oct. 3, 1984; June 3, June 27, Nov. 25, 
  1986; Dec. 23, 1987; Apr. 29, 1988; June 16, 
  1989; Mar. 26, June 29, 1990; Oct. 7, 1991; 
  Sept. 17, Nov. 10, 1992; May 25, 1993; Apr. 15, 
  Aug. 4, 1994; June 21, Dec. 7, 1995; Feb. 12, 
  July 25, 1996; Jan. 17, Jan. 27, May 2, Aug. 7, 
  1997
  New Mexico: Apr. 10, Dec. 24, 1980; Mar. 26, 
  June 18, Aug. 6, Aug. 19, Aug. 27, 1981 (2 
  amendments); Mar. 30, Apr. 16, May 3, May 5 (2 
  amendments), Oct. 6, Dec. 7, 1982; July 1, Aug. 
  24, 1983; Mar. 8, July 27, Aug. 13, Nov. 2, 
  1984; Mar. 4, 1985; Feb. 27, 1987; Nov. 2, 1988; 
  Oct. 27, 1989; June 4, Aug. 21, 1990; Mar. 5, 
  May 2, July 17, Nov. 12, 1991; Feb. 23 (2 
  amendments), May 12, Sept. 9, Nov. 29, Dec. 21 
  (2 amendments), 1993; Mar. 16, May 5, Nov. 11, 
  1994; Nov. 8, 1995; June 13, June 24, Sept. 13, 
  Oct. 15, 1996; Mar. 26, Sept. 26, 1997
  New York: Feb. 5, Mar. 6, Apr. 24, May 21, July 
  1, Nov. 10, 1980; Jan. 27 (2 amendments), Mar. 
  19 (2 amendments), Apr. 27, May 26, Sept. 9, 
  Sept. 24, Nov. 12, 1981; Feb. 22, Mar. 5, Aug. 
  11, 1982; Jan. 26 (2 amendments), June 1, Aug. 
  2, Dec. 20, 1984; May 30, June 17, July 19, 
  1985; Nov. 7, 1986; Sept. 15, 1988; Mar. 7, June 
  21, Nov. 28, 1989; Mar. 26, Aug. 7, 1991; July 
  27 (2 amendments), Sept. 29, 1993; Aug. 4, 1994; 
  Jan. 6, 1995; July 25, 1996; Sept. 23, Dec. 23, 
  1997; Apr. 30, 1998
  North Carolina: Jan. 10, Apr. 17, Aug. 20, Sept. 
  10, 1980; Mar. 19, Apr. 13, Apr. 16, May 15, 
  Aug. 27, Nov. 30, 1981; Feb. 23, July 26, Dec. 
  7, 1982; Jan. 26, Feb. 10, July 8, Nov. 15, 
  1983; Mar. 26, Sept. 14, 1984; Oct. 15, 1985; 
  Jan. 26, June 3, Sept. 9, Nov. 19, 1986 (2 
  amendments); Apr. 3, Apr. 17, Sept. 9, Dec. 15, 
  1987; Feb. 29, Apr. 5, Apr. 6, June 9, Dec. 12, 
  1988; Jan. 18, Mar. 9 (2 amendments), Mar. 16, 
  Dec. 20, 1989; Jan. 16, Mar. 12, June 12, 1990; 
  May 2, May 21, 1991; Sept. 9, 1993; Apr. 18, 
  June 23, June 30, Aug. 15, Sept. 21, Oct. 18, 
  Oct. 31, 1994; Jan. 26, May 5, May 8, June 1, 
  July 5, July 28 (2 amendments), Aug. 2, Sept. 5, 
  Oct. 4, 1995; Feb. 1 (2 amendments), Feb. 14, 
  May 23, Sept. 20 (2 amendments), 1996
  North Dakota: Nov. 2, 1979; Aug. 12, 1980; Nov. 
  12, 1982; Sept. 18, 1984; Sept. 28, Nov. 14, 
  1988; May 12, June 7, 1989; Aug. 9, 1990; June 
  20, 1991; June 26, 1992, June 21, Oct. 20, 1993; 
  Aug. 21, Nov. 3, 1995; Oct. 8, Nov. 29, 1996; 
  Apr. 21, 1997

[[Page 538]]

  Ohio: Oct. 31 (3 amendments), Nov. 28, 1980; 
  Jan. 27, Mar. 4, Mar. 31, May 1, June 18, Aug. 
  11, Aug. 28, Nov. 20, Nov. 27, Dec. 29, 1981; 
  Jan. 22, Mar. 8, Mar. 22, May 13, May 14, June 
  10, June 30, July 26, Aug. 10, Oct. 1, 1982; 
  Mar. 2, Mar. 30, July 5 (2 documents), July 7, 
  July 8, Aug. 25, Nov. 11, Dec. 2, 1983; Feb. 23, 
  May 15, June 1, July 6, Aug. 13, Dec. 13, 1984; 
  Jan. 7, Jan. 10, Feb. 1, June 13, 1985; Sept. 2, 
  Nov. 24, 1986; Dec. 8, Dec. 30, 1987; May 20, 
  Aug. 25, Sept. 15, 1988; Jan. 17, Jan. 18, Apr. 
  5, Aug. 9, Dec. 7, 1989; Nov. 2, Dec. 3, 1990; 
  Jan. 27, 1992; Mar. 22, Sept. 8, Oct. 22, Dec. 
  17, 1993; Feb. 4, May 9, May 27, Aug. 23, Sept. 
  13, Oct. 13, Oct. 20, Oct. 25, Dec. 8, 1994; 
  Mar. 23, Apr. 4, May 2, Aug. 1, Oct. 27, Oct. 
  30, 1995; Mar. 11, Apr. 25, May 6, May 15, May 
  16, June 12, Oct. 9, 1996; Jan. 6, Feb. 25, Apr. 
  16, Sept. 12, Sept. 22, 1997; Mar. 23, 1998
  Oklahoma: Feb. 13, Nov. 28, 1980; May 26, Aug. 
  6, 1981; Apr. 13, Apr. 16, May 14, Aug. 3, 1982; 
  May 18, Aug. 15, Aug. 25, 1983; Jan. 25, Apr. 2, 
  Apr. 25, July 27, 1984; Mar. 26, 1985; June 12, 
  June 29, Aug. 20, Oct. 18, 1990; Jan. 31, Feb. 
  12, July 23, Aug. 8, 1991; Mar. 6, 1992; June 
  23, 1994; Feb. 29, Apr. 9, 1996; May 14, 1997
  Oregon: July 30, 1979; Apr. 18, June 24, July 
  15, 1980; Jan. 2, Mar. 4, Aug. 27, Nov. 5, Nov. 
  6, 1981; Apr. 12 (4 amendments), July 7, Aug. 
  13, Oct. 7, 1982; Mar. 2, Mar. 17, May 18, July 
  7, Oct. 24, 1983; Apr. 20, Aug. 15, Sept. 11, 
  Sept. 20, Oct. 15, 1984; Jan. 8, Apr. 16, Apr. 
  18, Aug. 2, 1985; Jan. 16, Apr. 10, Apr. 21, 
  June 4, June 27, 1986; Feb. 13, Mar. 13, July 
  29, Aug. 25, 1987; Jan. 15 (2 amendments), Nov. 
  22, 1988; Mar. 1, Oct. 12, 1989; Apr. 23, Apr. 
  26, July 30, Sept. 13, 1991; June 9, Aug. 19 (4 
  amendments), 1992; Feb. 23, June 4, Sept. 9, 
  Sept. 29, Dec. 6, Dec. 17, 1993; Jan. 19, Feb. 
  15, Mar. 24, May 17, June 29, July 1, Aug. 24, 
  1994; Jan. 11, Feb. 15, July 19, Sept. 5, 1995; 
  May 16, July 18, Sept. 27, 1996; Feb. 25, Mar. 7 
  (2 amendments), May 19, June 20, Sept. 2, 1997; 
  Mar. 31, May 6, May 13, 1998
  Pennsylvania: July 7, Aug. 8, Dec. 17, 1979; May 
  20, Aug. 19, 1980; Aug. 5, Aug. 18, Aug. 27, 
  Aug. 28, Sept. 15, Sept. 17, Oct. 21, Nov. 3, 
  Dec. 16, Dec. 29, 1981; Feb. 26, Apr. 16, June 
  9, Oct. 7, Dec. 6, 1982; Jan. 19, Jan. 21, Mar. 
  15, May 12, July 5, July 6, Oct. 12, Nov. 22, 
  1983; Feb. 6, July 27 (2 amendments), Aug. 1, 
  Aug. 21, 1984; Feb. 26, 1985; Nov. 6, 1986; Jan. 
  14, Apr. 8, Oct. 19, 1987; Apr. 21, 1988; Jan. 
  23, 1989; May 16, 1990; Sept. 17, Sept. 23, Nov. 
  5, 1992; Apr. 6, Apr. 12, May 13, June 16 (4 
  amendments), June 30, Sept. 28, Oct. 19, Oct. 
  26, 1993; Feb. 10, June 13, July 21, Dec. 22, 
  1994; Jan. 12, Feb. 15 (2 amendments), Aug. 8, 
  Aug. 10, Aug. 18, Sept. 8, Nov. 3, Dec. 13, 
  1995; Jan. 30, Feb. 12, Apr. 2, Apr. 9, May 16, 
  June 11 (2 amendments), June 12, July 30 (2 
  amendments), Oct. 22, Dec. 20 (2 amendments), 
  1996; Jan. 29, Mar. 11, Apr. 18 (3 amendments), 
  May 7, June 3, June 11 (2 amendments), July 21, 
  Aug. 12, Aug. 21, Sept. 27, Sept. 29, Dec. 9, 
  1997; Mar. 9, Mar. 23, June 8, June 12, June 29, 
  1998

[[Page 539]]

  Rhode Island: Jan. 15, Jan. 21, May 7, Dec. 30, 
  1981; Apr. 26, Nov. 10, 1982; Mar. 29, June 28, 
  July 6, Sept. 15, 1983; May 15, July 6, July 27, 
  1984; Jan. 8, July 31, Dec. 11, 1986; Aug. 31, 
  Sept. 1, Sept. 28, 1987; Feb. 10, 1988; Mar. 10, 
  June 2, Sept. 19, 1989; Aug. 31, Sept. 6, 1990; 
  Sept. 30, Oct. 7, 1991; Dec. 17, 1993; Oct. 18, 
  1994; Jan. 10, 1995; Feb. 2, Feb. 6, Mar. 22, 
  Apr. 4, Oct. 30, 1996; Apr. 17, Sept. 2, 1997
  South Carolina: Sept. 21, 1979; Jan. 29, July 7, 
  1980; July 7, July 17, Aug. 7, Nov. 6, Nov. 13, 
  Nov. 24, Nov. 30, Dec. 16, 1981; Feb. 10, July 
  26, Sept. 3, 1982; Feb. 8, Oct. 31, 1983; Oct. 
  29, 1984; Jan. 21, 1986; Feb. 17, May 28, 1987; 
  Oct. 3, 1989 (2 amendments); July 2, 1990; Feb. 
  4, Dec. 15, 1992; Apr. 15, 1994; Feb. 24, Dec. 
  11, 1995; Feb. 16, 1996; July 1, Aug. 20, Sept. 
  11, 1997
  South Dakota: July 30, Aug. 9, 1979; Sept. 4, 
  1980; Nov. 3, 1981; July 7, 1983; Sept. 26, 
  1984; Sept. 2, 1988; June 7, 1989; Jan. 21, July 
  12, 1993; Oct. 25, 1994; Sept. 6, 1995
  Tennessee: Jan. 10, Feb. 6, Apr. 24, Aug. 13, 
  Nov. 17, 1980; Sept. 2, Nov. 16, Nov. 24, Nov. 
  30, Dec. 15, Dec. 16, 1981; May 12, May 27, June 
  9, June 21, June 24, July 26, Oct. 25, Dec. 7, 
  1982; Mar. 15, Mar. 22, May 2, July 18, Oct. 31, 
  1983; Jan. 11, June 21, July 27, Aug. 7, Aug. 8, 
  Oct. 19, 1984; Feb. 26, Mar. 29, Apr. 23, July 
  19, Aug. 12, Sept. 13, 1985; Mar. 19, June 3, 
  Dec. 31, 1986; Jan. 14, Jan. 15, Mar. 2, June 
  16, Dec. 3, Dec. 10, 1987; June 23 (6 
  amendments), July 6, Aug. 23, Oct. 12, Oct. 19, 
  Nov. 23, Nov. 25, Dec. 2, 1988; Jan. 23, Jan. 
  27, June 15, June 28, Aug. 3, Dec. 12, Dec. 20, 
  1989; Feb. 21, May 8, May 16, 1990; Mar. 11, 
  Sept. 9, 1991; June 26, Sept. 3, 1992; Feb. 23, 
  Apr. 7, Apr. 28 (2 amendments), Sept. 27, 1993; 
  Apr. 15, Apr. 18, July 26, Aug. 4, Sept. 15, 
  Nov. 1, 1994; Jan. 17, Feb. 9, Feb. 10, Feb. 27, 
  1994; May 8, July 28 (2 amendments), Sept. 11, 
  Dec. 26, 1995; Mar. 19, Apr. 2, Apr. 3, July 18, 
  July 24, July 29 (2 amendments), Aug. 27, Sept. 
  6, Oct. 15, Oct. 30, 1996; Feb. 13, Feb. 18, 
  Mar. 26, May 30, June 17, July 2, July 21, July 
  29, July 30, Aug. 5, Aug. 12, Aug. 15, Nov. 25, 
  1997; June 8, 1998
  Texas: Sept. 24, Dec. 18, 1979; Mar. 25, Aug. 6, 
  1980; July 10, Aug. 28, Sept. 29, Nov. 13, Dec. 
  15, 1981; Jan. 27, Mar. 29, May 14, May 19, June 
  23, July 1, July 28 (2 amendments), Aug. 13, 
  Oct. 7, Oct. 25, Nov. 10, 1982; Feb. 25, Mar. 
  31, Aug. 15, Oct. 4, Nov. 7, 1983; Aug. 13 (2 
  amendments), Aug. 15, 1984; June 26, July 1, 
  1985; Nov. 24, 1986; May 6, Nov. 22, 1988; Feb. 
  9, Feb. 23, May 5, 1989; Aug. 3, Sept. 6, Oct. 
  12, 1990; Aug. 14, Sept. 10, 1991; June 24, 
  Sept. 24, 1992; Aug. 30, 1993; Jan. 18, Jan. 20, 
  Apr. 15, Aug. 19, Aug. 22, Aug. 26, Sept. 9, 
  Sept. 12, Sept. 15, Oct. 4, Nov. 29, 1994; Mar. 
  6, Mar 7 (2 amendments), Apr. 3, June 5, June 
  19, Sept. 27, Nov. 8, 1995; May 8, Sept. 23, 
  Oct. 30, 1996; Feb. 18, May 22, May 30, Aug. 19, 
  1997; Feb. 9, Feb. 10, Mar. 11, June 8, July 1, 
  1998
  Utah: Feb. 19, Sept. 10, 1980; May 5, 1981; Feb. 
  12, May 28, Aug. 4, 1982; Dec. 21, 1983; July 
  11, Aug. 15, 1984; Feb. 20, 1985; May 30, 1986; 
  Jan. 17, Mar. 8, June 7, 1989; June 24, 1991; 
  June 26, 1992; July 8, Nov. 8, Dec. 14, 1994; 
  May 5, June 29, Nov. 3, 1995; Mar. 8, May 6, 
  Nov. 29, 1996; Apr. 9, May 7, 1997

[[Page 540]]

  Vermont: Jan. 30, Feb. 19, Sept. 9, 1980; Mar. 
  16, Mar. 18, 1981; Jan. 7, Feb. 10, Apr. 16, 
  1982; Aug. 23, 1983; Feb. 26, 1985; July 17, 
  1987; Mar. 5, 1991; Jan. 10, 1995; Apr. 9, July 
  17, Aug. 4, 1997; Apr. 22, 1998
  Virginia: Dec. 17, 1979; Jan. 31, Aug. 19, Oct. 
  8 (2 amendments), Dec. 5, 1980; Mar. 18, Apr. 
  20, Aug. 6, Aug. 17, Aug. 18, Aug. 27, Sept. 3, 
  Oct. 6, Nov. 6 (2 amendments), Nov. 23, 1981; 
  Jan. 13, Feb. 24, Mar. 1, Mar. 8, Apr. 6, May 3, 
  May 4, May 6, Sept. 28, 1982; Feb. 25, Mar. 4, 
  Aug. 18, Sept. 15, 1983; Jan. 25, Jan. 30, Mar. 
  23, Mar. 26, June 1, June 5, Oct. 9, 1984; June 
  25, 1985; Aug. 20, 1990; Nov. 1, 1991; Jan. 27, 
  Mar. 6, Mar. 18, May 6, May 18, Aug. 11, Oct. 
  26, 1992; Feb. 23, Feb. 25, June 16, Aug. 30, 
  1993; Mar. 31, Apr. 15, June 23, Aug. 23, Oct. 
  19, 1994; May 2, Aug. 23, Sept. 27, Sept. 28, 
  Dec. 8, 1995; June 13, July 24, 1996; Mar. 12 (3 
  amendments), June 26, July 21, Oct. 14 (2 
  amendments), Oct. 21, Nov. 17, 1997; Mar. 11, 
  Mar. 23, 1998
  Washington: July 30, 1979, June 5, July 31, Dec. 
  24, 1980; Apr. 15, Aug. 14, Sept. 14, 1981; Feb. 
  23, Mar. 22, Apr. 14, Dec. 17, 1982; Feb. 28, 
  June 29, 1983; July 6, July 9, Aug. 21, 1984; 
  Jan. 29, Apr. 22, 1985; Mar. 27, 1986; Jan. 2, 
  May 4, 1987; May 29, 1991; Jan. 15, July 12, 
  July 27 (2 amendments), 1993; Jan. 20, June 23, 
  Aug. 4, Aug. 29, Sept. 12, Oct. 12, Oct. 31, 
  1994; Feb. 22, Mar. 8, May 3, May 5, June 2, 
  June 29, Aug. 23, Oct. 24 (2 amendments), Oct. 
  25, 1995; Feb. 14, May 23, July 23, July 25, 
  Aug. 8, Sept. 6 (2 amendments), Sept. 23, Sept. 
  25, Sept. 26, Sept. 27, Oct. 10, Oct. 11, Oct. 
  21, 1996; Jan. 27, Feb. 26, Mar. 20, Apr. 30, 
  May 19, Aug. 6, Sept. 22, Dec. 31, 1997; Feb. 2, 
  Apr. 21, June 25, 1998
  West Virginia: Aug. 14, Nov. 10, Nov. 20, 1980; 
  Aug. 27, Oct. 29, Nov. 20, 1981; Mar. 16, Sept. 
  1, Dec. 9, 1982; Sept. 20, 1983; Apr. 27, 1984; 
  July 2, 1985; Apr. 11, 1986; Apr. 24, 1991; 
  Sept. 17, 1992; May 18, June 28, 1993; Apr. 19, 
  July 25, Sept. 6 (3 amendments), Dec. 21, 1994; 
  Feb. 1, Aug. 4 (2 amendments), Sept. 5, 1995; 
  Oct. 22, Nov. 27, 1996
  Wisconsin: Jan. 11, 1980; Apr. 9, Apr. 17, May 
  6, June 9, Aug. 14, Aug. 20, Oct. 21, Nov. 27, 
  1981; Apr. 13, May 17, June 21, Nov. 15, 1982; 
  Mar. 9, Nov. 28, 1983; Jan. 25, Mar. 9, Aug. 1, 
  Nov. 6, 1984; Feb. 25, Mar. 14, May 10, June 28, 
  Aug. 9, 1985; June 25, Sept. 9, Nov. 24 (2 
  amendments), Dec. 15, Dec. 23, 1986; Sept. 9, 
  1988; Apr. 5, Sept. 6, Nov. 2, 1989; Feb. 1, 
  Mar. 27, Apr. 6, Nov. 30, 1990; Nov. 5, 1991; 
  Oct. 8, Nov. 11, 1992; May 21, June 28, Aug. 13, 
  Dec. 6, 1993; Feb. 1, Mar. 1, Aug. 10, Aug. 15, 
  Aug. 19, Aug. 24, Dec. 7, 1994; Jan. 12, Jan. 
  18, Jan. 31, June 30, July 28, 1995; Feb. 12 (2 
  amendments), Feb. 13, Mar. 11, Mar. 22, Apr. 4, 
  Apr. 9, Apr. 25, Apr. 29, July 17, July 29, Aug. 
  29, 1996
  Wyoming: July 2, Sept. 6, 1979; Apr. 27, 1981; 
  Feb. 9, 1982; Apr. 19, 1983; Oct. 11, 1984; May 
  12, 1986; Feb. 15, Mar. 17, June 7, 1989; July 
  10, 1990; May 24, 1991; June 20, June 23, Nov. 
  29, 1994; Sept. 12, Nov. 3, 1995
  American Samoa: Aug. 14, 1985
  Guam: Mar. 6, 1980; May 12, 1981; Sept. 30, 
  1982; May 15, 1984; Jan. 22, Aug. 14, 1985
  Northern Mariana Islands: Nov. 13, 1987

[[Page 541]]

  Puerto Rico: Nov. 3, 1980; Apr. 27, 1981; Sept. 
  3, 1982; Oct. 20, 1983; Feb. 22, Apr. 18, 1985; 
  Oct. 16, 1987; May 31, 1995; Jan. 22, 1997
  Virgin Islands: May 2, 1980; Apr. 27, Sept. 3, 
  1981; Mar. 4, 1983; Feb. 7, Feb. 26, 1985; Feb. 
  13, 1987; Mar. 18, 1994
  Copies of the Plans listed above are available 
  at the Environmental Protection Agency, Public 
  Information Reference Unit, Room 2904, 401 M St. 
  SW., Washington, DC 20460 and at the appropriate 
  EPA Regional Office as follows:


EPA Region

  I--Connecticut, Maine, Massachusetts, New 
  Hampshire, Rhode Island, Vermont--JFK Federal 
  Bldg., Boston, MA 02203
  II--New York, New Jersey, Puerto Rico, Virgin 
  Islands--Federal Office Bldg., 26 Federal Plaza, 
  New York, NY 10278
  III--Delaware, District of Columbia, 
  Pennsylvania, Maryland, Virginia, West 
  Virginia--841 Chestnut St., Philadelphia, PA 
  19107
  IV--Alabama, Florida, Georgia, Mississippi, 
  Kentucky, North Carolina, South Carolina, 
  Tennessee--345 Courtland St. NE., Atlanta, GA 
  30365
  V--Illinois, Indiana, Michigan, Minnesota, Ohio, 
  Wisconsin--Federal Bldg., 230 South Dearborn 
  St., Chicago, IL 60604
  VI--Arkansas, Louisiana, New Mexico, Oklahoma, 
  Texas--1201 Elm St., Dallas, TX 75270
  VII--Iowa, Kansas, Missouri, Nebraska--726 
  Minnesota Ave., Kansas City, KS 66101
  VIII--Colorado, Montana, North Dakota, South 
  Dakota, Utah, Wyoming--999 18th St., Denver, CO 
  80202
  IX--Arizona, California, Hawaii, Nevada, Guam, 
  American Samoa, Northern Mariana Islands--215 
  Fremont St., San Francisco, CA 94105
  X--Washington, Oregon, Idaho, Alaska--1200 6th 
  Ave., Seattle, WA 98101
  Copies are available at: Environmental 
  Protection Agency Library, 401 M St. SW., Room 
  2904, Washington, DC 20460; Environmental 
  Protection Agency, Office of Air Quality 
  Planning and Standards, 411 Chapel Hill St., 
  Durham, NC 27701


American Petroleum Institute

  1220 L Street NW., Washington, DC 20037
Evaporation Loss from External Floating-Roof              52.741; 52.742
  Tanks, Publication 2517, second edition, 
  February 1980.


American Society for Testing and Materials

  100 Barr Harbor Drive, West Conshohocken, PA 
  19428-2959, Telephone (610) 832-9585, FAX (610) 
  FAX (610) 832-9555
D-86-82 Standard Method for Distillation of               52.741; 52.742
  Petroleum Products.
D 323-82 Standard Test Method for Vapor Pressure          52.741; 52.742
  of Petroleum Products (Reid Method).
D 1475-85 Standard Test Method for Density of             52.741; 52.742
  Paint, Varnish, Lacquer, and Related Products.
D 2369-87 Standard Test Method for Volatile               52.741; 52.742
  Content of Coatings.
D 2372-85 Standard Test Method for Separation of          52.741; 52.742
  Vehicle from Solvent-Reducible Paints.
D 2697-86 Standard Test Method for Volume                 52.741; 52.742
Nonvolatile Matter in Clear or Pigmented 
[[Page 542]]

D 2879-86 Standard Test Method for Vapor Pressure-        52.741; 52.742
  Temperature Relationship and Initial 
  Decomposition Temperature of Liquids by 
  Isoteniscope.
D 3792-86 Standard Test Method for Water Content          52.741; 52.742
  of Water-Reducible Paints by Direct Injection 
  into a Gas Chromatograph.
D 3925-81 (Reapproved 1985) Standard Practice for         52.741; 52.742
  Sampling Liquid Paints and Related Pigment 
  Coatings.
D 3980-87 Standard Practice for Interlaboratory           52.741; 52.742
  Testing of Paint and Related Materials.
D 4017-81 (Reapproved 1987) Standard Test Method          52.741; 52.742
  for Water in Paints and Paint Materials by the 
  Karl Fischer Method.
D 4457-85 Standard Test Method for Determination          52.741; 52.742
  of Dichloromethane and 1,1,1-Trichloroethane in 
  Paints and Coatings by Direct Injection into a 
  Gas Chromatograph.
E 180-85 Standard Practice for Determining the            52.741; 52.742
  Precision of ASTM Methods for Analysis and 
  Testing of Industrial Chemicals.
E 300-86 Standard Practice for Sampling Industrial        52.741; 52.742
  Chemicals.


National Technical Information Service

  5285 Port Royal Rd., Springfield, VA 22161, 
  Telephone: (703) 487-4650, FAX: (703) 487-4142
``Guideline on Air Quality Models (Revised)''                   52.21(l)
  (1986), and Supplement A (1987), EPA 450/2-78-
  027R.


U.S. Environmental Protection Agency

  Air and Radiation Division, Region V, 230 S. 
  Dearborn, Chicago, IL 60604
35 Illinois Administrative Code 215, June 1989,           52.741; 52.742
  Subparts (B), (E) (sections 215.182, 215.183, 
  215.184), (K) (sections 215.301 and 215.302), 
  (Q) (excluding sections 215.432 and 215.236), 
  (R) (excluding sections 215.447, 215.450, and 
  215.452), (S), (V), (X), (Y) (sections 215.582, 
  215.583, 215.584), and (Z).


U.S. Government Printing Office

  Washington, DC 20402, Telephone: (202) 512-1800
Standard Industrial Classification Manual, 1987...        52.741; 52.742



[[Page 543]]



                    Table of CFR Titles and Chapters




                      (Revised as of June 29, 1998)

                      Title 1--General Provisions

         I  Administrative Committee of the Federal Register 
                (Parts 1--49)
        II  Office of the Federal Register (Parts 50--299)
        IV  Miscellaneous Agencies (Parts 400--500)

                          Title 2--[Reserved]

                        Title 3--The President

         I  Executive Office of the President (Parts 100--199)

                           Title 4--Accounts

         I  General Accounting Office (Parts 1--99)
        II  Federal Claims Collection Standards (General 
                Accounting Office--Department of Justice) (Parts 
                100--299)

                   Title 5--Administrative Personnel

         I  Office of Personnel Management (Parts 1--1199)
        II  Merit Systems Protection Board (Parts 1200--1299)
       III  Office of Management and Budget (Parts 1300--1399)
        IV  Advisory Committee on Federal Pay (Parts 1400--1499)
         V  The International Organizations Employees Loyalty 
                Board (Parts 1500--1599)
        VI  Federal Retirement Thrift Investment Board (Parts 
                1600--1699)
       VII  Advisory Commission on Intergovernmental Relations 
                (Parts 1700--1799)
      VIII  Office of Special Counsel (Parts 1800--1899)
        IX  Appalachian Regional Commission (Parts 1900--1999)
        XI  Armed Forces Retirement Home (Part 2100)
       XIV  Federal Labor Relations Authority, General Counsel of 
                the Federal Labor Relations Authority and Federal 
                Service Impasses Panel (Parts 2400--2499)
        XV  Office of Administration, Executive Office of the 
                President (Parts 2500--2599)
       XVI  Office of Government Ethics (Parts 2600--2699)
       XXI  Department of the Treasury (Parts 3100--3199)

[[Page 544]]

      XXII  Federal Deposit Insurance Corporation (Part 3201)
     XXIII  Department of Energy (Part 3301)
      XXIV  Federal Energy Regulatory Commission (Part 3401)
       XXV  Department of the Interior (Part 3501)
      XXVI  Department of Defense (Part 3601)
    XXVIII  Department of Justice (Part 3801)
      XXIX  Federal Communications Commission (Parts 3900--3999)
       XXX  Farm Credit System Insurance Corporation (Parts 4000--
                4099)
      XXXI  Farm Credit Administration (Parts 4100--4199)
    XXXIII  Overseas Private Investment Corporation (Part 4301)
      XXXV  Office of Personnel Management (Part 4501)
        XL  Interstate Commerce Commission (Part 5001)
       XLI  Commodity Futures Trading Commission (Part 5101)
      XLII  Department of Labor (Part 5201)
     XLIII  National Science Foundation (Part 5301)
       XLV  Department of Health and Human Services (Part 5501)
      XLVI  Postal Rate Commission (Part 5601)
     XLVII  Federal Trade Commission (Part 5701)
    XLVIII  Nuclear Regulatory Commission (Part 5801)
         L  Department of Transportation (Part 6001)
       LII  Export-Import Bank of the United States (Part 6201)
      LIII  Department of Education (Parts 6300--6399)
       LIV  Environmental Protection Agency (Part 6401)
      LVII  General Services Administration (Part 6701)
     LVIII  Board of Governors of the Federal Reserve System (Part 
                6801)
       LIX  National Aeronautics and Space Administration (Part 
                6901)
        LX  United States Postal Service (Part 7001)
       LXI  National Labor Relations Board (Part 7101)
      LXII  Equal Employment Opportunity Commission (Part 7201)
     LXIII  Inter-American Foundation (Part 7301)
       LXV  Department of Housing and Urban Development (Part 
                7501)
      LXVI  National Archives and Records Administration (Part 
                7601)
      LXIX  Tennessee Valley Authority (Part 7901)
      LXXI  Consumer Product Safety Commission (Part 8101)
     LXXIV  Federal Mine Safety and Health Review Commission (Part 
                8401)
     LXXVI  Federal Retirement Thrift Investment Board (Part 8601)
    LXXVII  Office of Management and Budget (Part 8701)

                          Title 6--[Reserved]

                         Title 7--Agriculture

            Subtitle A--Office of the Secretary of Agriculture 
                (Parts 0--26)
            Subtitle B--Regulations of the Department of 
                Agriculture

[[Page 545]]

         I  Agricultural Marketing Service (Standards, 
                Inspections, Marketing Practices), Department of 
                Agriculture (Parts 27--209)
        II  Food and Nutrition Service, Department of Agriculture 
                (Parts 210--299)
       III  Animal and Plant Health Inspection Service, Department 
                of Agriculture (Parts 300--399)
        IV  Federal Crop Insurance Corporation, Department of 
                Agriculture (Parts 400--499)
         V  Agricultural Research Service, Department of 
                Agriculture (Parts 500--599)
        VI  Natural Resources Conservation Service, Department of 
                Agriculture (Parts 600--699)
       VII  Farm Service Agency, Department of Agriculture (Parts 
                700--799)
      VIII  Grain Inspection, Packers and Stockyards 
                Administration (Federal Grain Inspection Service), 
                Department of Agriculture (Parts 800--899)
        IX  Agricultural Marketing Service (Marketing Agreements 
                and Orders; Fruits, Vegetables, Nuts), Department 
                of Agriculture (Parts 900--999)
         X  Agricultural Marketing Service (Marketing Agreements 
                and Orders; Milk), Department of Agriculture 
                (Parts 1000--1199)
        XI  Agricultural Marketing Service (Marketing Agreements 
                and Orders; Miscellaneous Commodities), Department 
                of Agriculture (Parts 1200--1299)
      XIII  Northeast Dairy Compact Commission (Parts 1300--1399)
       XIV  Commodity Credit Corporation, Department of 
                Agriculture (Parts 1400--1499)
        XV  Foreign Agricultural Service, Department of 
                Agriculture (Parts 1500--1599)
       XVI  Rural Telephone Bank, Department of Agriculture (Parts 
                1600--1699)
      XVII  Rural Utilities Service, Department of Agriculture 
                (Parts 1700--1799)
     XVIII  Rural Housing Service, Rural Business-Cooperative 
                Service, Rural Utilities Service, and Farm Service 
                Agency, Department of Agriculture (Parts 1800--
                2099)
      XXVI  Office of Inspector General, Department of Agriculture 
                (Parts 2600--2699)
     XXVII  Office of Information Resources Management, Department 
                of Agriculture (Parts 2700--2799)
    XXVIII  Office of Operations, Department of Agriculture (Parts 
                2800--2899)
      XXIX  Office of Energy, Department of Agriculture (Parts 
                2900--2999)
       XXX  Office of the Chief Financial Officer, Department of 
                Agriculture (Parts 3000--3099)
      XXXI  Office of Environmental Quality, Department of 
                Agriculture (Parts 3100--3199)
     XXXII  [Reserved]

[[Page 546]]

    XXXIII  Office of Transportation, Department of Agriculture 
                (Parts 3300--3399)
     XXXIV  Cooperative State Research, Education, and Extension 
                Service, Department of Agriculture (Parts 3400--
                3499)
      XXXV  Rural Housing Service, Department of Agriculture 
                (Parts 3500--3599)
     XXXVI  National Agricultural Statistics Service, Department 
                of Agriculture (Parts 3600--3699)
    XXXVII  Economic Research Service, Department of Agriculture 
                (Parts 3700--3799)
   XXXVIII  World Agricultural Outlook Board, Department of 
                Agriculture (Parts 3800--3899)
       XLI  [Reserved]
      XLII  Rural Business-Cooperative Service and Rural Utilities 
                Service, Department of Agriculture (Parts 4200--
                4299)

                    Title 8--Aliens and Nationality

         I  Immigration and Naturalization Service, Department of 
                Justice (Parts 1--499)

                 Title 9--Animals and Animal Products

         I  Animal and Plant Health Inspection Service, Department 
                of Agriculture (Parts 1--199)
        II  Grain Inspection, Packers and Stockyards 
                Administration (Packers and Stockyards Programs), 
                Department of Agriculture (Parts 200--299)
       III  Food Safety and Inspection Service, Meat and Poultry 
                Inspection, Department of Agriculture (Parts 300--
                599)

                           Title 10--Energy

         I  Nuclear Regulatory Commission (Parts 0--199)
        II  Department of Energy (Parts 200--699)
       III  Department of Energy (Parts 700--999)
         X  Department of Energy (General Provisions) (Parts 
                1000--1099)
        XI  United States Enrichment Corporation (Parts 1100--
                1199)
      XVII  Defense Nuclear Facilities Safety Board (Parts 1700--
                1799)

                      Title 11--Federal Elections

         I  Federal Election Commission (Parts 1--9099)

                      Title 12--Banks and Banking

         I  Comptroller of the Currency, Department of the 
                Treasury (Parts 1--199)
        II  Federal Reserve System (Parts 200--299)

[[Page 547]]

       III  Federal Deposit Insurance Corporation (Parts 300--399)
        IV  Export-Import Bank of the United States (Parts 400--
                499)
         V  Office of Thrift Supervision, Department of the 
                Treasury (Parts 500--599)
        VI  Farm Credit Administration (Parts 600--699)
       VII  National Credit Union Administration (Parts 700--799)
      VIII  Federal Financing Bank (Parts 800--899)
        IX  Federal Housing Finance Board (Parts 900--999)
        XI  Federal Financial Institutions Examination Council 
                (Parts 1100--1199)
       XIV  Farm Credit System Insurance Corporation (Parts 1400--
                1499)
        XV  Thrift Depositor Protection Oversight Board (Parts 
                1500--1599)
      XVII  Office of Federal Housing Enterprise Oversight, 
                Department of Housing and Urban Development (Parts 
                1700-1799)
     XVIII  Community Development Financial Institutions Fund, 
                Department of the Treasury (Parts 1800--1899)

               Title 13--Business Credit and Assistance

         I  Small Business Administration (Parts 1--199)
       III  Economic Development Administration, Department of 
                Commerce (Parts 300--399)

                    Title 14--Aeronautics and Space

         I  Federal Aviation Administration, Department of 
                Transportation (Parts 1--199)
        II  Office of the Secretary, Department of Transportation 
                (Aviation Proceedings) (Parts 200--399)
       III  Commercial Space Transportation, Federal Aviation 
                Administration, Department of Transportation 
                (Parts 400--499)
         V  National Aeronautics and Space Administration (Parts 
                1200--1299)

                 Title 15--Commerce and Foreign Trade

            Subtitle A--Office of the Secretary of Commerce (Parts 
                0--29)
            Subtitle B--Regulations Relating to Commerce and 
                Foreign Trade
         I  Bureau of the Census, Department of Commerce (Parts 
                30--199)
        II  National Institute of Standards and Technology, 
                Department of Commerce (Parts 200--299)
       III  International Trade Administration, Department of 
                Commerce (Parts 300--399)
        IV  Foreign-Trade Zones Board, Department of Commerce 
                (Parts 400--499)
       VII  Bureau of Export Administration, Department of 
                Commerce (Parts 700--799)

[[Page 548]]

      VIII  Bureau of Economic Analysis, Department of Commerce 
                (Parts 800--899)
        IX  National Oceanic and Atmospheric Administration, 
                Department of Commerce (Parts 900--999)
        XI  Technology Administration, Department of Commerce 
                (Parts 1100--1199)
      XIII  East-West Foreign Trade Board (Parts 1300--1399)
       XIV  Minority Business Development Agency (Parts 1400--
                1499)
            Subtitle C--Regulations Relating to Foreign Trade 
                Agreements
        XX  Office of the United States Trade Representative 
                (Parts 2000--2099)
            Subtitle D--Regulations Relating to Telecommunications 
                and Information
     XXIII  National Telecommunications and Information 
                Administration, Department of Commerce (Parts 
                2300--2399)

                    Title 16--Commercial Practices

         I  Federal Trade Commission (Parts 0--999)
        II  Consumer Product Safety Commission (Parts 1000--1799)

             Title 17--Commodity and Securities Exchanges

         I  Commodity Futures Trading Commission (Parts 1--199)
        II  Securities and Exchange Commission (Parts 200--399)
        IV  Department of the Treasury (Parts 400--499)

          Title 18--Conservation of Power and Water Resources

         I  Federal Energy Regulatory Commission, Department of 
                Energy (Parts 1--399)
       III  Delaware River Basin Commission (Parts 400--499)
        VI  Water Resources Council (Parts 700--799)
      VIII  Susquehanna River Basin Commission (Parts 800--899)
      XIII  Tennessee Valley Authority (Parts 1300--1399)

                       Title 19--Customs Duties

         I  United States Customs Service, Department of the 
                Treasury (Parts 1--199)
        II  United States International Trade Commission (Parts 
                200--299)
       III  International Trade Administration, Department of 
                Commerce (Parts 300--399)

                     Title 20--Employees' Benefits

         I  Office of Workers' Compensation Programs, Department 
                of Labor (Parts 1--199)

[[Page 549]]

        II  Railroad Retirement Board (Parts 200--399)
       III  Social Security Administration (Parts 400--499)
        IV  Employees' Compensation Appeals Board, Department of 
                Labor (Parts 500--599)
         V  Employment and Training Administration, Department of 
                Labor (Parts 600--699)
        VI  Employment Standards Administration, Department of 
                Labor (Parts 700--799)
       VII  Benefits Review Board, Department of Labor (Parts 
                800--899)
      VIII  Joint Board for the Enrollment of Actuaries (Parts 
                900--999)
        IX  Office of the Assistant Secretary for Veterans' 
                Employment and Training, Department of Labor 
                (Parts 1000--1099)

                       Title 21--Food and Drugs

         I  Food and Drug Administration, Department of Health and 
                Human Services (Parts 1--1299)
        II  Drug Enforcement Administration, Department of Justice 
                (Parts 1300--1399)
       III  Office of National Drug Control Policy (Parts 1400--
                1499)

                      Title 22--Foreign Relations

         I  Department of State (Parts 1--199)
        II  Agency for International Development, International 
                Development Cooperation Agency (Parts 200--299)
       III  Peace Corps (Parts 300--399)
        IV  International Joint Commission, United States and 
                Canada (Parts 400--499)
         V  United States Information Agency (Parts 500--599)
        VI  United States Arms Control and Disarmament Agency 
                (Parts 600--699)
       VII  Overseas Private Investment Corporation, International 
                Development Cooperation Agency (Parts 700--799)
        IX  Foreign Service Grievance Board Regulations (Parts 
                900--999)
         X  Inter-American Foundation (Parts 1000--1099)
        XI  International Boundary and Water Commission, United 
                States and Mexico, United States Section (Parts 
                1100--1199)
       XII  United States International Development Cooperation 
                Agency (Parts 1200--1299)
      XIII  Board for International Broadcasting (Parts 1300--
                1399)
       XIV  Foreign Service Labor Relations Board; Federal Labor 
                Relations Authority; General Counsel of the 
                Federal Labor Relations Authority; and the Foreign 
                Service Impasse Disputes Panel (Parts 1400--1499)
        XV  African Development Foundation (Parts 1500--1599)
       XVI  Japan-United States Friendship Commission (Parts 
                1600--1699)
      XVII  United States Institute of Peace (Parts 1700--1799)

[[Page 550]]

                          Title 23--Highways

         I  Federal Highway Administration, Department of 
                Transportation (Parts 1--999)
        II  National Highway Traffic Safety Administration and 
                Federal Highway Administration, Department of 
                Transportation (Parts 1200--1299)
       III  National Highway Traffic Safety Administration, 
                Department of Transportation (Parts 1300--1399)

                Title 24--Housing and Urban Development

            Subtitle A--Office of the Secretary, Department of 
                Housing and Urban Development (Parts 0--99)
            Subtitle B--Regulations Relating to Housing and Urban 
                Development
         I  Office of Assistant Secretary for Equal Opportunity, 
                Department of Housing and Urban Development (Parts 
                100--199)
        II  Office of Assistant Secretary for Housing-Federal 
                Housing Commissioner, Department of Housing and 
                Urban Development (Parts 200--299)
       III  Government National Mortgage Association, Department 
                of Housing and Urban Development (Parts 300--399)
         V  Office of Assistant Secretary for Community Planning 
                and Development, Department of Housing and Urban 
                Development (Parts 500--599)
        VI  Office of Assistant Secretary for Community Planning 
                and Development, Department of Housing and Urban 
                Development (Parts 600--699) [Reserved]
       VII  Office of the Secretary, Department of Housing and 
                Urban Development (Housing Assistance Programs and 
                Public and Indian Housing Programs) (Parts 700--
                799)
      VIII  Office of the Assistant Secretary for Housing--deral 
                Housing Commissioner, Department of Housing and 
                Urban Development (Section 8 Housing Assistance 
                Programs and Section 202 Direct Loan Program) 
                (Parts 800--899)
        IX  Office of Assistant Secretary for Public and Indian 
                Housing, Department of Housing and Urban 
                Development (Parts 900--999)
         X  Office of Assistant Secretary for Housing--Federal 
                Housing Commissioner, Department of Housing and 
                Urban Development (Interstate Land Sales 
                Registration Program) (Parts 1700--1799)
       XII  Office of Inspector General, Department of Housing and 
                Urban Development (Parts 2000--2099)
        XX  Office of Assistant Secretary for Housing--Federal 
                Housing Commissioner, Department of Housing and 
                Urban Development (Parts 3200--3899)
       XXV  Neighborhood Reinvestment Corporation (Parts 4100--
                4199)

                           Title 25--Indians

         I  Bureau of Indian Affairs, Department of the Interior 
                (Parts 1--299)

[[Page 551]]

        II  Indian Arts and Crafts Board, Department of the 
                Interior (Parts 300--399)
       III  National Indian Gaming Commission, Department of the 
                Interior (Parts 500--599)
        IV  Office of Navajo and Hopi Indian Relocation (Parts 
                700--799)
         V  Bureau of Indian Affairs, Department of the Interior, 
                and Indian Health Service, Department of Health 
                and Human Services (Part 900)
        VI  Office of the Assistant Secretary-Indian Affairs, 
                Department of the Interior (Part 1001)
       VII  Office of the Special Trustee for American Indians, 
                Department of the Interior (Part 1200)

                      Title 26--Internal Revenue

         I  Internal Revenue Service, Department of the Treasury 
                (Parts 1--799)

           Title 27--Alcohol, Tobacco Products and Firearms

         I  Bureau of Alcohol, Tobacco and Firearms, Department of 
                the Treasury (Parts 1--299)

                   Title 28--Judicial Administration

         I  Department of Justice (Parts 0--199)
       III  Federal Prison Industries, Inc., Department of Justice 
                (Parts 300--399)
         V  Bureau of Prisons, Department of Justice (Parts 500--
                599)
        VI  Offices of Independent Counsel, Department of Justice 
                (Parts 600--699)
       VII  Office of Independent Counsel (Parts 700--799)

                            Title 29--Labor

            Subtitle A--Office of the Secretary of Labor (Parts 
                0--99)
            Subtitle B--Regulations Relating to Labor
         I  National Labor Relations Board (Parts 100--199)
        II  Office of Labor-Management Standards, Department of 
                Labor (Parts 200--299)
       III  National Railroad Adjustment Board (Parts 300--399)
        IV  Office of Labor-Management Standards, Department of 
                Labor (Parts 400--499)
         V  Wage and Hour Division, Department of Labor (Parts 
                500--899)
        IX  Construction Industry Collective Bargaining Commission 
                (Parts 900--999)
         X  National Mediation Board (Parts 1200--1299)
       XII  Federal Mediation and Conciliation Service (Parts 
                1400--1499)
       XIV  Equal Employment Opportunity Commission (Parts 1600--
                1699)

[[Page 552]]

      XVII  Occupational Safety and Health Administration, 
                Department of Labor (Parts 1900--1999)
        XX  Occupational Safety and Health Review Commission 
                (Parts 2200--2499)
       XXV  Pension and Welfare Benefits Administration, 
                Department of Labor (Parts 2500--2599)
     XXVII  Federal Mine Safety and Health Review Commission 
                (Parts 2700--2799)
        XL  Pension Benefit Guaranty Corporation (Parts 4000--
                4999)

                      Title 30--Mineral Resources

         I  Mine Safety and Health Administration, Department of 
                Labor (Parts 1--199)
        II  Minerals Management Service, Department of the 
                Interior (Parts 200--299)
       III  Board of Surface Mining and Reclamation Appeals, 
                Department of the Interior (Parts 300--399)
        IV  Geological Survey, Department of the Interior (Parts 
                400--499)
        VI  Bureau of Mines, Department of the Interior (Parts 
                600--699)
       VII  Office of Surface Mining Reclamation and Enforcement, 
                Department of the Interior (Parts 700--999)

                 Title 31--Money and Finance: Treasury

            Subtitle A--Office of the Secretary of the Treasury 
                (Parts 0--50)
            Subtitle B--Regulations Relating to Money and Finance
         I  Monetary Offices, Department of the Treasury (Parts 
                51--199)
        II  Fiscal Service, Department of the Treasury (Parts 
                200--399)
        IV  Secret Service, Department of the Treasury (Parts 
                400--499)
         V  Office of Foreign Assets Control, Department of the 
                Treasury (Parts 500--599)
        VI  Bureau of Engraving and Printing, Department of the 
                Treasury (Parts 600--699)
       VII  Federal Law Enforcement Training Center, Department of 
                the Treasury (Parts 700--799)
      VIII  Office of International Investment, Department of the 
                Treasury (Parts 800--899)

                      Title 32--National Defense

            Subtitle A--Department of Defense
         I  Office of the Secretary of Defense (Parts 1--399)
         V  Department of the Army (Parts 400--699)
        VI  Department of the Navy (Parts 700--799)
       VII  Department of the Air Force (Parts 800--1099)
            Subtitle B--Other Regulations Relating to National 
                Defense

[[Page 553]]

       XII  Defense Logistics Agency (Parts 1200--1299)
       XVI  Selective Service System (Parts 1600--1699)
       XIX  Central Intelligence Agency (Parts 1900--1999)
        XX  Information Security Oversight Office, National 
                Archives and Records Administration (Parts 2000--
                2099)
       XXI  National Security Council (Parts 2100--2199)
      XXIV  Office of Science and Technology Policy (Parts 2400--
                2499)
     XXVII  Office for Micronesian Status Negotiations (Parts 
                2700--2799)
    XXVIII  Office of the Vice President of the United States 
                (Parts 2800--2899)
      XXIX  Presidential Commission on the Assignment of Women in 
                the Armed Forces (Part 2900)

               Title 33--Navigation and Navigable Waters

         I  Coast Guard, Department of Transportation (Parts 1--
                199)
        II  Corps of Engineers, Department of the Army (Parts 
                200--399)
        IV  Saint Lawrence Seaway Development Corporation, 
                Department of Transportation (Parts 400--499)

                          Title 34--Education

            Subtitle A--Office of the Secretary, Department of 
                Education (Parts 1--99)
            Subtitle B--Regulations of the Offices of the 
                Department of Education
         I  Office for Civil Rights, Department of Education 
                (Parts 100--199)
        II  Office of Elementary and Secondary Education, 
                Department of Education (Parts 200--299)
       III  Office of Special Education and Rehabilitative 
                Services, Department of Education (Parts 300--399)
        IV  Office of Vocational and Adult Education, Department 
                of Education (Parts 400--499)
         V  Office of Bilingual Education and Minority Languages 
                Affairs, Department of Education (Parts 500--599)
        VI  Office of Postsecondary Education, Department of 
                Education (Parts 600--699)
       VII  Office of Educational Research and Improvement, 
                Department of Education (Parts 700--799)
        XI  National Institute for Literacy (Parts 1100-1199)
            Subtitle C--Regulations Relating to Education
       XII  National Council on Disability (Parts 1200--1299)

                        Title 35--Panama Canal

         I  Panama Canal Regulations (Parts 1--299)

[[Page 554]]

             Title 36--Parks, Forests, and Public Property

         I  National Park Service, Department of the Interior 
                (Parts 1--199)
        II  Forest Service, Department of Agriculture (Parts 200--
                299)
       III  Corps of Engineers, Department of the Army (Parts 
                300--399)
        IV  American Battle Monuments Commission (Parts 400--499)
         V  Smithsonian Institution (Parts 500--599)
       VII  Library of Congress (Parts 700--799)
      VIII  Advisory Council on Historic Preservation (Parts 800--
                899)
        IX  Pennsylvania Avenue Development Corporation (Parts 
                900--999)
        XI  Architectural and Transportation Barriers Compliance 
                Board (Parts 1100--1199)
       XII  National Archives and Records Administration (Parts 
                1200--1299)
       XIV  Assassination Records Review Board (Parts 1400-1499)

             Title 37--Patents, Trademarks, and Copyrights

         I  Patent and Trademark Office, Department of Commerce 
                (Parts 1--199)
        II  Copyright Office, Library of Congress (Parts 200--299)
        IV  Assistant Secretary for Technology Policy, Department 
                of Commerce (Parts 400--499)
         V  Under Secretary for Technology, Department of Commerce 
                (Parts 500--599)

           Title 38--Pensions, Bonuses, and Veterans' Relief

         I  Department of Veterans Affairs (Parts 0--99)

                       Title 39--Postal Service

         I  United States Postal Service (Parts 1--999)
       III  Postal Rate Commission (Parts 3000--3099)

                  Title 40--Protection of Environment

         I  Environmental Protection Agency (Parts 1--799)
         V  Council on Environmental Quality (Parts 1500--1599)

          Title 41--Public Contracts and Property Management

            Subtitle B--Other Provisions Relating to Public 
                Contracts
        50  Public Contracts, Department of Labor (Parts 50-1--50-
                999)
        51  Committee for Purchase From People Who Are Blind or 
                Severely Disabled (Parts 51-1--51-99)
        60  Office of Federal Contract Compliance Programs, Equal 
                Employment Opportunity, Department of Labor (Parts 
                60-1--60-999)
        61  Office of the Assistant Secretary for Veterans 
                Employment and Training, Department of Labor 
                (Parts 61-1--61-999)

[[Page 555]]

            Subtitle C--Federal Property Management Regulations 
                System
       101  Federal Property Management Regulations (Parts 101-1--
                101-99)
       105  General Services Administration (Parts 105-1--105-999)
       109  Department of Energy Property Management Regulations 
                (Parts 109-1--109-99)
       114  Department of the Interior (Parts 114-1--114-99)
       115  Environmental Protection Agency (Parts 115-1--115-99)
       128  Department of Justice (Parts 128-1--128-99)
            Subtitle D--Other Provisions Relating to Property 
                Management [Reserved]
            Subtitle E--Federal Information Resources Management 
                Regulations System
       201  Federal Information Resources Management Regulation 
                (Parts 201-1--201-99) [Reserved]
            Subtitle F--Federal Travel Regulation System
       300  General
       301  Temporary Duty (TDY) Travel Allowances (Parts 301-1--
                301-99)
       302  Relocation Allowances (Parts 302-1--302-99)
       303  Payment of Expenses Connected with the Death of 
                Certain Employees (Parts 303-1--303-2)
       304  Payment from a Non-Federal Source for Travel Expenses 
                (Parts 304-1--304-99)

                        Title 42--Public Health

         I  Public Health Service, Department of Health and Human 
                Services (Parts 1--199)
        IV  Health Care Financing Administration, Department of 
                Health and Human Services (Parts 400--499)
         V  Office of Inspector General-Health Care, Department of 
                Health and Human Services (Parts 1000--1999)

                   Title 43--Public Lands: Interior

            Subtitle A--Office of the Secretary of the Interior 
                (Parts 1--199)
            Subtitle B--Regulations Relating to Public Lands
         I  Bureau of Reclamation, Department of the Interior 
                (Parts 200--499)
        II  Bureau of Land Management, Department of the Interior 
                (Parts 1000--9999)
       III  Utah Reclamation Mitigation and Conservation 
                Commission (Parts 10000--10005)

             Title 44--Emergency Management and Assistance

         I  Federal Emergency Management Agency (Parts 0--399)
        IV  Department of Commerce and Department of 
                Transportation (Parts 400--499)

[[Page 556]]

                       Title 45--Public Welfare

            Subtitle A--Department of Health and Human Services 
                (Parts 1--199)
            Subtitle B--Regulations Relating to Public Welfare
        II  Office of Family Assistance (Assistance Programs), 
                Administration for Children and Families, 
                Department of Health and Human Services (Parts 
                200--299)
       III  Office of Child Support Enforcement (Child Support 
                Enforcement Program), Administration for Children 
                and Families, Department of Health and Human 
                Services (Parts 300--399)
        IV  Office of Refugee Resettlement, Administration for 
                Children and Families, Department of Health and 
                Human Services (Parts 400--499)
         V  Foreign Claims Settlement Commission of the United 
                States, Department of Justice (Parts 500--599)
        VI  National Science Foundation (Parts 600--699)
       VII  Commission on Civil Rights (Parts 700--799)
      VIII  Office of Personnel Management (Parts 800--899)
         X  Office of Community Services, Administration for 
                Children and Families, Department of Health and 
                Human Services (Parts 1000--1099)
        XI  National Foundation on the Arts and the Humanities 
                (Parts 1100--1199)
       XII  Corporation for National and Community Service (Parts 
                1200--1299)
      XIII  Office of Human Development Services, Department of 
                Health and Human Services (Parts 1300--1399)
       XVI  Legal Services Corporation (Parts 1600--1699)
      XVII  National Commission on Libraries and Information 
                Science (Parts 1700--1799)
     XVIII  Harry S. Truman Scholarship Foundation (Parts 1800--
                1899)
       XXI  Commission on Fine Arts (Parts 2100--2199)
      XXII  Christopher Columbus Quincentenary Jubilee Commission 
                (Parts 2200--2299)
     XXIII  Arctic Research Commission (Part 2301)
      XXIV  James Madison Memorial Fellowship Foundation (Parts 
                2400--2499)
       XXV  Corporation for National and Community Service (Parts 
                2500--2599)

                          Title 46--Shipping

         I  Coast Guard, Department of Transportation (Parts 1--
                199)
        II  Maritime Administration, Department of Transportation 
                (Parts 200--399)
       III  Coast Guard (Great Lakes Pilotage), Department of 
                Transportation (Parts 400--499)
        IV  Federal Maritime Commission (Parts 500--599)

[[Page 557]]

                      Title 47--Telecommunication

         I  Federal Communications Commission (Parts 0--199)
        II  Office of Science and Technology Policy and National 
                Security Council (Parts 200--299)
       III  National Telecommunications and Information 
                Administration, Department of Commerce (Parts 
                300--399)

           Title 48--Federal Acquisition Regulations System

         1  Federal Acquisition Regulation (Parts 1--99)
         2  Department of Defense (Parts 200--299)
         3  Department of Health and Human Services (Parts 300--
                399)
         4  Department of Agriculture (Parts 400--499)
         5  General Services Administration (Parts 500--599)
         6  Department of State (Parts 600--699)
         7  United States Agency for International Development 
                (Parts 700--799)
         8  Department of Veterans Affairs (Parts 800--899)
         9  Department of Energy (Parts 900--999)
        10  Department of the Treasury (Parts 1000--1099)
        12  Department of Transportation (Parts 1200--1299)
        13  Department of Commerce (Parts 1300--1399)
        14  Department of the Interior (Parts 1400--1499)
        15  Environmental Protection Agency (Parts 1500--1599)
        16  Office of Personnel Management Federal Employees 
                Health Benefits Acquisition Regulation (Parts 
                1600--1699)
        17  Office of Personnel Management (Parts 1700--1799)
        18  National Aeronautics and Space Administration (Parts 
                1800--1899)
        19  United States Information Agency (Parts 1900--1999)
        20  Nuclear Regulatory Commission (Parts 2000--2099)
        21  Office of Personnel Management, Federal Employees 
                Group Life Insurance Federal Acquisition 
                Regulation (Parts 2100--2199)
        23  Social Security Administration (Parts 2300--2399)
        24  Department of Housing and Urban Development (Parts 
                2400--2499)
        25  National Science Foundation (Parts 2500--2599)
        28  Department of Justice (Parts 2800--2899)
        29  Department of Labor (Parts 2900--2999)
        34  Department of Education Acquisition Regulation (Parts 
                3400--3499)
        35  Panama Canal Commission (Parts 3500--3599)
        44  Federal Emergency Management Agency (Parts 4400--4499)
        51  Department of the Army Acquisition Regulations (Parts 
                5100--5199)
        52  Department of the Navy Acquisition Regulations (Parts 
                5200--5299)

[[Page 558]]

        53  Department of the Air Force Federal Acquisition 
                Regulation Supplement (Parts 5300--5399)
        54  Defense Logistics Agency, Department of Defense (Part 
                5452)
        57  African Development Foundation (Parts 5700--5799)
        61  General Services Administration Board of Contract 
                Appeals (Parts 6100--6199)
        63  Department of Transportation Board of Contract Appeals 
                (Parts 6300--6399)
        99  Cost Accounting Standards Board, Office of Federal 
                Procurement Policy, Office of Management and 
                Budget (Parts 9900--9999)

                       Title 49--Transportation

            Subtitle A--Office of the Secretary of Transportation 
                (Parts 1--99)
            Subtitle B--Other Regulations Relating to 
                Transportation
         I  Research and Special Programs Administration, 
                Department of Transportation (Parts 100--199)
        II  Federal Railroad Administration, Department of 
                Transportation (Parts 200--299)
       III  Federal Highway Administration, Department of 
                Transportation (Parts 300--399)
        IV  Coast Guard, Department of Transportation (Parts 400--
                499)
         V  National Highway Traffic Safety Administration, 
                Department of Transportation (Parts 500--599)
        VI  Federal Transit Administration, Department of 
                Transportation (Parts 600--699)
       VII  National Railroad Passenger Corporation (AMTRAK) 
                (Parts 700--799)
      VIII  National Transportation Safety Board (Parts 800--999)
         X  Surface Transportation Board, Department of 
                Transportation (Parts 1000--1399)

                   Title 50--Wildlife and Fisheries

         I  United States Fish and Wildlife Service, Department of 
                the Interior (Parts 1--199)
        II  National Marine Fisheries Service, National Oceanic 
                and Atmospheric Administration, Department of 
                Commerce (Parts 200--299)
       III  International Fishing and Related Activities (Parts 
                300--399)
        IV  Joint Regulations (United States Fish and Wildlife 
                Service, Department of the Interior and National 
                Marine Fisheries Service, National Oceanic and 
                Atmospheric Administration, Department of 
                Commerce); Endangered Species Committee 
                Regulations (Parts 400--499)
         V  Marine Mammal Commission (Parts 500--599)

[[Page 559]]

        VI  Fishery Conservation and Management, National Oceanic 
                and Atmospheric Administration, Department of 
                Commerce (Parts 600--699)

                      CFR Index and Finding Aids

            Subject/Agency Index
            List of Agency Prepared Indexes
            Parallel Tables of Statutory Authorities and Rules
            List of CFR Titles, Chapters, Subchapters, and Parts
            Alphabetical List of Agencies Appearing in the CFR



[[Page 561]]





           Alphabetical List of Agencies Appearing in the CFR




                      (Revised as of June 29, 1998)

                                                  CFR Title, Subtitle or 
                     Agency                               Chapter

Administrative Committee of the Federal Register  1, I
Advanced Research Projects Agency                 32, I
Advisory Commission on Intergovernmental          5, VII
     Relations
Advisory Committee on Federal Pay                 5, IV
Advisory Council on Historic Preservation         36, VIII
African Development Foundation                    22, XV
  Federal Acquisition Regulation                  48, 57
Agency for International Development, United      22, II
     States
  Federal Acquisition Regulation                  48, 7
Agricultural Marketing Service                    7, I, IX, X, XI
Agricultural Research Service                     7, V
Agriculture Department
  Agricultural Marketing Service                  7, I, IX, X, XI
  Agricultural Research Service                   7, V
  Animal and Plant Health Inspection Service      7, III; 9, I
  Chief Financial Officer, Office of              7, XXX
  Commodity Credit Corporation                    7, XIV
  Cooperative State Research, Education, and      7, XXXIV
       Extension Service
  Economic Research Service                       7, XXXVII
  Energy, Office of                               7, XXIX
  Environmental Quality, Office of                7, XXXI
  Farm Service Agency                             7, VII, XVIII
  Federal Acquisition Regulation                  48, 4
  Federal Crop Insurance Corporation              7, IV
  Food and Nutrition Service                      7, II
  Food Safety and Inspection Service              9, III
  Foreign Agricultural Service                    7, XV
  Forest Service                                  36, II
  Grain Inspection, Packers and Stockyards        7, VIII; 9, II
       Administration
  Information Resources Management, Office of     7, XXVII
  Inspector General, Office of                    7, XXVI
  National Agricultural Library                   7, XLI
  National Agricultural Statistics Service        7, XXXVI
  Natural Resources Conservation Service          7, VI
  Operations, Office of                           7, XXVIII
  Rural Business-Cooperative Service              7, XVIII, XLII
  Rural Development Administration                7, XLII
  Rural Housing Service                           7, XVIII, XXXV
  Rural Telephone Bank                            7, XVI
  Rural Utilities Service                         7, XVII, XVIII, XLII
  Secretary of Agriculture, Office of             7, Subtitle A
  Transportation, Office of                       7, XXXIII
  World Agricultural Outlook Board                7, XXXVIII
Air Force Department                              32, VII
  Federal Acquisition Regulation Supplement       48, 53
Alcohol, Tobacco and Firearms, Bureau of          27, I
AMTRAK                                            49, VII
American Battle Monuments Commission              36, IV
American Indians, Office of the Special Trustee   25, VII
Animal and Plant Health Inspection Service        7, III; 9, I
Appalachian Regional Commission                   5, IX
Architectural and Transportation Barriers         36, XI
   Compliance Board
[[Page 562]]

Arctic Research Commission                        45, XXIII
Armed Forces Retirement Home                      5, XI
Arms Control and Disarmament Agency, United       22, VI
     States
Army Department                                   32, V
  Engineers, Corps of                             33, II; 36, III
  Federal Acquisition Regulation                  48, 51
Assassination Records Review Board                36, XIV
Benefits Review Board                             20, VII
Bilingual Education and Minority Languages        34, V
     Affairs, Office of
Blind or Severely Disabled, Committee for         41, 51
     Purchase From People Who Are
Board for International Broadcasting              22, XIII
Census Bureau                                     15, I
Central Intelligence Agency                       32, XIX
Chief Financial Officer, Office of                7, XXX
Child Support Enforcement, Office of              45, III
Children and Families, Administration for         45, II, III, IV, X
Christopher Columbus Quincentenary Jubilee        45, XXII
     Commission
Civil Rights, Commission on                       45, VII
Civil Rights, Office for                          34, I
Coast Guard                                       33, I; 46, I; 49, IV
Coast Guard (Great Lakes Pilotage)                46, III
Commerce Department                               44, IV
  Census Bureau                                   15, I`
  Economic Affairs, Under Secretary               37, V
  Economic Analysis, Bureau of                    15, VIII
  Economic Development Administration             13, III
  Emergency Management and Assistance             44, IV
  Export Administration, Bureau of                15, VII
  Federal Acquisition Regulation                  48, 13
  Fishery Conservation and Management             50, VI
  Foreign-Trade Zones Board                       15, IV
  International Trade Administration              15, III; 19, III
  National Institute of Standards and Technology  15, II
  National Marine Fisheries Service               50, II, IV
  National Oceanic and Atmospheric                15, IX; 50, II, III, IV, 
       Administration                             VI
  National Telecommunications and Information     15, XXIII; 47, III
       Administration
  National Weather Service                        15, IX
  Patent and Trademark Office                     37, I
  Productivity, Technology and Innovation,        37, IV
       Assistant Secretary for
  Secretary of Commerce, Office of                15, Subtitle A
  Technology, Under Secretary for                 37, V
  Technology Administration                       15, XI
  Technology Policy, Assistant Secretary for      37, IV
Commercial Space Transportation                   14, III
Commodity Credit Corporation                      7, XIV
Commodity Futures Trading Commission              5, XLI; 17, I
Community Planning and Development, Office of     24, V, VI
     Assistant Secretary for
Community Services, Office of                     45, X
Comptroller of the Currency                       12, I
Construction Industry Collective Bargaining       29, IX
     Commission
Consumer Product Safety Commission                5, LXXI; 16, II
Cooperative State Research, Education, and        7, XXXIV
     Extension Service
Copyright Office                                  37, II
Corporation for National and Community Service    45, XII, XXV
Cost Accounting Standards Board                   48, 99
Council on Environmental Quality                  40, V
Customs Service, United States                    19, I
Defense Contract Audit Agency                     32, I
Defense Department                                5, XXVI; 32, Subtitle A
  Advanced Research Projects Agency               32, I
  Air Force Department                            32, VII

[[Page 563]]

  Army Department                                 32, V; 33, II; 36, III, 
                                                  48, 51
  Defense Intelligence Agency                     32, I
  Defense Logistics Agency                        32, I, XII; 48, 54
  Engineers, Corps of                             33, II; 36, III
  Federal Acquisition Regulation                  48, 2
  National Imagery and Mapping Agency             32, I
  Navy Department                                 32, VI; 48, 52
  Secretary of Defense, Office of                 32, I
Defense Contract Audit Agency                     32, I
Defense Intelligence Agency                       32, I
Defense Logistics Agency                          32, XII; 48, 54
Defense Nuclear Facilities Safety Board           10, XVII
Delaware River Basin Commission                   18, III
Drug Enforcement Administration                   21, II
East-West Foreign Trade Board                     15, XIII
Economic Affairs, Under Secretary                 37, V
Economic Analysis, Bureau of                      15, VIII
Economic Development Administration               13, III
Economic Research Service                         7, XXXVII
Education, Department of                          5, LIII
  Bilingual Education and Minority Languages      34, V
       Affairs, Office of
  Civil Rights, Office for                        34, I
  Educational Research and Improvement, Office    34, VII
       of
  Elementary and Secondary Education, Office of   34, II
  Federal Acquisition Regulation                  48, 34
  Postsecondary Education, Office of              34, VI
  Secretary of Education, Office of               34, Subtitle A
  Special Education and Rehabilitative Services,  34, III
       Office of
  Vocational and Adult Education, Office of       34, IV
Educational Research and Improvement, Office of   34, VII
Elementary and Secondary Education, Office of     34, II
Employees' Compensation Appeals Board             20, IV
Employees Loyalty Board                           5, V
Employment and Training Administration            20, V
Employment Standards Administration               20, VI
Endangered Species Committee                      50, IV
Energy, Department of                             5, XXIII; 10, II, III, X
  Federal Acquisition Regulation                  48, 9
  Federal Energy Regulatory Commission            5, XXIV; 18, I
  Property Management Regulations                 41, 109
Energy, Office of                                 7, XXIX
Engineers, Corps of                               33, II; 36, III
Engraving and Printing, Bureau of                 31, VI
Enrichment Corporation, United States             10, XI
Environmental Protection Agency                   5, LIV; 40, I
  Federal Acquisition Regulation                  48, 15
  Property Management Regulations                 41, 115
Environmental Quality, Office of                  7, XXXI
Equal Employment Opportunity Commission           5, LXII; 29, XIV
Equal Opportunity, Office of Assistant Secretary  24, I
     for
Executive Office of the President                 3, I
  Administration, Office of                       5, XV
  Environmental Quality, Council on               40, V
  Management and Budget, Office of                25, III, LXXVII; 48, 99
  National Drug Control Policy, Office of         21, III
  National Security Council                       32, XXI; 47, 2
  Presidential Documents                          3
  Science and Technology Policy, Office of        32, XXIV; 47, II
  Trade Representative, Office of the United      15, XX
       States
Export Administration, Bureau of                  15, VII
Export-Import Bank of the United States           5, LII; 12, IV
Family Assistance, Office of                      45, II
Farm Credit Administration                        5, XXXI; 12, VI
Farm Credit System Insurance Corporation          5, XXX; 12, XIV
Farm Service Agency                               7, VII, XVIII

[[Page 564]]

Federal Acquisition Regulation                    48, 1
Federal Aviation Administration                   14, I
  Commercial Space Transportation                 14, III
Federal Claims Collection Standards               4, II
Federal Communications Commission                 5, XXIX; 47, I
Federal Contract Compliance Programs, Office of   41, 60
Federal Crop Insurance Corporation                7, IV
Federal Deposit Insurance Corporation             5, XXII; 12, III
Federal Election Commission                       11, I
Federal Emergency Management Agency               44, I
  Federal Acquisition Regulation                  48, 44
Federal Employees Group Life Insurance Federal    48, 21
     Acquisition Regulation
Federal Employees Health Benefits Acquisition     48, 16
     Regulation
Federal Energy Regulatory Commission              5, XXIV; 18, I
Federal Financial Institutions Examination        12, XI
     Council
Federal Financing Bank                            12, VIII
Federal Highway Administration                    23, I, II; 49, III
Federal Home Loan Mortgage Corporation            1, IV
Federal Housing Enterprise Oversight Office       12, XVII
Federal Housing Finance Board                     12, IX
Federal Labor Relations Authority, and General    5, XIV; 22, XIV
     Counsel of the Federal Labor Relations 
     Authority
Federal Law Enforcement Training Center           31, VII
Federal Maritime Commission                       46, IV
Federal Mediation and Conciliation Service        29, XII
Federal Mine Safety and Health Review Commission  5, LXXIV; 29, XXVII
Federal Pay, Advisory Committee on                5, IV
Federal Prison Industries, Inc.                   28, III
Federal Procurement Policy Office                 48, 99
Federal Property Management Regulations           41, 101
Federal Property Management Regulations System    41, Subtitle C
Federal Railroad Administration                   49, II
Federal Register, Administrative Committee of     1, I
Federal Register, Office of                       1, II
Federal Reserve System                            12, II
  Board of Governors                              5, LVIII
Federal Retirement Thrift Investment Board        5, VI, LXXVI
Federal Service Impasses Panel                    5, XIV
Federal Trade Commission                          5, XLVII; 16, I
Federal Transit Administration                    49, VI
Federal Travel Regulation System                  41, Subtitle F
Fine Arts, Commission on                          45, XXI
Fiscal Service                                    31, II
Fish and Wildlife Service, United States          50, I, IV
Fishery Conservation and Management               50, VI
Food and Drug Administration                      21, I
Food and Nutrition Service                        7, II
Food Safety and Inspection Service                9, III
Foreign Agricultural Service                      7, XV
Foreign Assets Control, Office of                 31, V
Foreign Claims Settlement Commission of the       45, V
     United States
Foreign Service Grievance Board                   22, IX
Foreign Service Impasse Disputes Panel            22, XIV
Foreign Service Labor Relations Board             22, XIV
Foreign-Trade Zones Board                         15, IV
Forest Service                                    36, II
General Accounting Office                         4, I, II
General Services Administration                   5, LVII
  Contract Appeals, Board of                      48, 61
  Federal Acquisition Regulation                  48, 5
  Federal Property Management Regulations System  41, 101, 105
  Federal Travel Regulation System                41, Subtitle F
  General                                         41, 300
  Payment From a Non-Federal Source for Travel    41, 304
       Expenses
  Payment of Expenses Connected With the Death    41, 303
     of Certain Employees
[[Page 565]]

  Relocation Allowances                           41, 302
  Temporary Duty (TDY) Travel Allowances          41, 301
Geological Survey                                 30, IV
Government Ethics, Office of                      5, XVI
Government National Mortgage Association          24, III
Grain Inspection, Packers and Stockyards          7, VIII; 9, II
     Administration
Great Lakes Pilotage                              46, III
Harry S. Truman Scholarship Foundation            45, XVIII
Health and Human Services, Department of          5, XLV; 45, Subtitle A
  Child Support Enforcement, Office of            45, III
  Children and Families, Administration for       45, II, III, IV, X
  Community Services, Office of                   45, X
  Family Assistance, Office of                    45, II
  Federal Acquisition Regulation                  48, 3
  Food and Drug Administration                    21, I
  Health Care Financing Administration            42, IV
  Human Development Services, Office of           45, XIII
  Indian Health Service                           25, V
  Inspector General (Health Care), Office of      42, V
  Public Health Service                           42, I
  Refugee Resettlement, Office of                 45, IV
Health Care Financing Administration              42, IV
Housing and Urban Development, Department of      5, LXV; 24, Subtitle B
  Community Planning and Development, Office of   24, V, VI
       Assistant Secretary for
  Equal Opportunity, Office of Assistant          24, I
       Secretary for
  Federal Acquisition Regulation                  48, 24
  Federal Housing Enterprise Oversight, Office    12, XVII
       of
  Government National Mortgage Association        24, III
  Housing--Federal Housing Commissioner, Office   24, II, VIII, X, XX
       of Assistant Secretary for
  Inspector General, Office of                    24, XII
  Public and Indian Housing, Office of Assistant  24, IX
       Secretary for
  Secretary, Office of                            24, Subtitle A, VII
Housing--Federal Housing Commissioner, Office of  24, II, VIII, X, XX
     Assistant Secretary for
Human Development Services, Office of             45, XIII
Immigration and Naturalization Service            8, I
Independent Counsel, Office of                    28, VII
Indian Affairs, Bureau of                         25, I, V
Indian Affairs, Office of the Assistant           25, VI
     Secretary
Indian Arts and Crafts Board                      25, II
Indian Health Service                             25, V
Information Agency, United States                 22, V
  Federal Acquisition Regulation                  48, 19
Information Resources Management, Office of       7, XXVII
Information Security Oversight Office, National   32, XX
     Archives and Records Administration
Inspector General
  Agriculture Department                          7, XXVI
  Health and Human Services Department            42, V
  Housing and Urban Development Department        24, XII
Institute of Peace, United States                 22, XVII
Inter-American Foundation                         5, LXIII; 22, X
Intergovernmental Relations, Advisory Commission  5, VII
     on
Interior Department
  American Indians, Office of the Special         25, VII
       Trustee
  Endangered Species Committee                    50, IV
  Federal Acquisition Regulation                  48, 14
  Federal Property Management Regulations System  41, 114
  Fish and Wildlife Service, United States        50, I, IV
  Geological Survey                               30, IV
  Indian Affairs, Bureau of                       25, I, V
  Indian Affairs, Office of the Assistant         25, VI
       Secretary
  Indian Arts and Crafts Board                    25, II
  Land Management, Bureau of                      43, II
  Minerals Management Service                     30, II

[[Page 566]]

  Mines, Bureau of                                30, VI
  National Indian Gaming Commission               25, III
  National Park Service                           36, I
  Reclamation, Bureau of                          43, I
  Secretary of the Interior, Office of            43, Subtitle A
  Surface Mining and Reclamation Appeals, Board   30, III
       of
  Surface Mining Reclamation and Enforcement,     30, VII
       Office of
Internal Revenue Service                          26, I
International Boundary and Water Commission,      22, XI
     United States and Mexico, United States 
     Section
International Development, United States Agency   22, II
     for
  Federal Acquisition Regulation                  48, 7
International Development Cooperation Agency,     22, XII
     United States
  International Development, United States        22, II; 48, 7
       Agency for
  Overseas Private Investment Corporation         5, XXXIII; 22, VII
International Fishing and Related Activities      50, III
International Investment, Office of               31, VIII
International Joint Commission, United States     22, IV
     and Canada
International Organizations Employees Loyalty     5, V
     Board
International Trade Administration                15, III; 19, III
International Trade Commission, United States     19, II
Interstate Commerce Commission                    5, XL
James Madison Memorial Fellowship Foundation      45, XXIV
Japan-United States Friendship Commission         22, XVI
Joint Board for the Enrollment of Actuaries       20, VIII
Justice Department                                5, XXVIII; 28, I
  Drug Enforcement Administration                 21, II
  Federal Acquisition Regulation                  48, 28
  Federal Claims Collection Standards             4, II
  Federal Prison Industries, Inc.                 28, III
  Foreign Claims Settlement Commission of the     45, V
       United States
  Immigration and Naturalization Service          8, I
  Offices of Independent Counsel                  28, VI
  Prisons, Bureau of                              28, V
  Property Management Regulations                 41, 128
Labor Department                                  5, XLII
  Benefits Review Board                           20, VII
  Employees' Compensation Appeals Board           20, IV
  Employment and Training Administration          20, V
  Employment Standards Administration             20, VI
  Federal Acquisition Regulation                  48, 29
  Federal Contract Compliance Programs, Office    41, 60
       of
  Federal Procurement Regulations System          41, 50
  Labor-Management Standards, Office of           29, II, IV
  Mine Safety and Health Administration           30, I
  Occupational Safety and Health Administration   29, XVII
  Pension and Welfare Benefits Administration     29, XXV
  Public Contracts                                41, 50
  Secretary of Labor, Office of                   29, Subtitle A
  Veterans' Employment and Training, Office of    41, 61; 20, IX
       the Assistant Secretary for
  Wage and Hour Division                          29, V
  Workers' Compensation Programs, Office of       20, I
Labor-Management Standards, Office of             29, II, IV
Land Management, Bureau of                        43, II
Legal Services Corporation                        45, XVI
Library of Congress                               36, VII
  Copyright Office                                37, II
Management and Budget, Office of                  5, III, LXXVII; 48, 99
Marine Mammal Commission                          50, V
Maritime Administration                           46, II
Merit Systems Protection Board                    5, II
Micronesian Status Negotiations, Office for       32, XXVII
Mine Safety and Health Administration             30, I
Minerals Management Service                       30, II

[[Page 567]]

Mines, Bureau of                                  30, VI
Minority Business Development Agency              15, XIV
Miscellaneous Agencies                            1, IV
Monetary Offices                                  31, I
National Aeronautics and Space Administration     5, LIX; 14, V
  Federal Acquisition Regulation                  48, 18
National Agricultural Library                     7, XLI
National Agricultural Statistics Service          7, XXXVI
National Archives and Records Administration      5, LXVI; 36, XII
  Information Security Oversight Office           32, XX
National Bureau of Standards                      15, II
National Capital Planning Commission              1, IV
National Commission for Employment Policy         1, IV
National Commission on Libraries and Information  45, XVII
     Science
National and Community Service, Corporation for   45, XII, XXV
National Council on Disability                    34, XII
National Credit Union Administration              12, VII
National Drug Control Policy, Office of           21, III
National Foundation on the Arts and the           45, XI
     Humanities
National Highway Traffic Safety Administration    23, II, III; 49, V
National Imagery and Mapping Agency               32, I
National Indian Gaming Commission                 25, III
National Institute for Literacy                   34, XI
National Institute of Standards and Technology    15, II
National Labor Relations Board                    5, LXI; 29, I
National Marine Fisheries Service                 50, II, IV
National Mediation Board                          29, X
National Oceanic and Atmospheric Administration   15, IX; 50, II, III, IV, 
                                                  VI
National Park Service                             36, I
National Railroad Adjustment Board                29, III
National Railroad Passenger Corporation (AMTRAK)  49, VII
National Science Foundation                       5, XLIII; 45, VI
  Federal Acquisition Regulation                  48, 25
National Security Council                         32, XXI
National Security Council and Office of Science   47, II
     and Technology Policy
National Telecommunications and Information       15, XXIII; 47, III
     Administration
National Transportation Safety Board              49, VIII
National Weather Service                          15, IX
Natural Resources Conservation Service            7, VI
Navajo and Hopi Indian Relocation, Office of      25, IV
Navy Department                                   32, VI
  Federal Acquisition Regulation                  48, 52
Neighborhood Reinvestment Corporation             24, XXV
Northeast Dairy Compact Commission                7, XIII
Nuclear Regulatory Commission                     5, XLVIII; 10, I
  Federal Acquisition Regulation                  48, 20
Occupational Safety and Health Administration     29, XVII
Occupational Safety and Health Review Commission  29, XX
Offices of Independent Counsel                    28, VI
Operations Office                                 7, XXVIII
Overseas Private Investment Corporation           5, XXXIII; 22, VII
Panama Canal Commission                           48, 35
Panama Canal Regulations                          35, I
Patent and Trademark Office                       37, I
Payment From a Non-Federal Source for Travel      41, 304
     Expenses
Payment of Expenses Connected With the Death of   41, 303
     Certain Employees
Peace Corps                                       22, III
Pennsylvania Avenue Development Corporation       36, IX
Pension and Welfare Benefits Administration       29, XXV
Pension Benefit Guaranty Corporation              29, XL
Personnel Management, Office of                   5, I, XXXV; 45, VIII
  Federal Acquisition Regulation                  48, 17
  Federal Employees Group Life Insurance Federal  48, 21
     Acquisition Regulation
[[Page 568]]

  Federal Employees Health Benefits Acquisition   48, 16
       Regulation
Postal Rate Commission                            5, XLVI; 39, III
Postal Service, United States                     5, LX; 39, I
Postsecondary Education, Office of                34, VI
President's Commission on White House             1, IV
     Fellowships
Presidential Commission on the Assignment of      32, XXIX
     Women in the Armed Forces
Presidential Documents                            3
Prisons, Bureau of                                28, V
Productivity, Technology and Innovation,          37, IV
     Assistant Secretary
Public Contracts, Department of Labor             41, 50
Public and Indian Housing, Office of Assistant    24, IX
     Secretary for
Public Health Service                             42, I
Railroad Retirement Board                         20, II
Reclamation, Bureau of                            43, I
Refugee Resettlement, Office of                   45, IV
Regional Action Planning Commissions              13, V
Relocation Allowances                             41, 302
Research and Special Programs Administration      49, I
Rural Business-Cooperative Service                7, XVIII, XLII
Rural Development Administration                  7, XLII
Rural Housing Service                             7, XVIII, XXXV
Rural Telephone Bank                              7, XVI
Rural Utilities Service                           7, XVII, XVIII, XLII
Saint Lawrence Seaway Development Corporation     33, IV
Science and Technology Policy, Office of          32, XXIV
Science and Technology Policy, Office of, and     47, II
     National Security Council
Secret Service                                    31, IV
Securities and Exchange Commission                17, II
Selective Service System                          32, XVI
Small Business Administration                     13, I
Smithsonian Institution                           36, V
Social Security Administration                    20, III; 48, 23
Soldiers' and Airmen's Home, United States        5, XI
Special Counsel, Office of                        5, VIII
Special Education and Rehabilitative Services,    34, III
     Office of
State Department                                  22, I
  Federal Acquisition Regulation                  48, 6
Surface Mining and Reclamation Appeals, Board of  30, III
Surface Mining Reclamation and Enforcement,       30, VII
     Office of
Surface Transportation Board                      49, X
Susquehanna River Basin Commission                18, VIII
Technology Administration                         15, XI
Technology Policy, Assistant Secretary for        37, IV
Technology, Under Secretary for                   37, V
Tennessee Valley Authority                        5, LXIX; 18, XIII
Thrift Depositor Protection Oversight Board       12, XV
Thrift Supervision Office, Department of the      12, V
     Treasury
Trade Representative, United States, Office of    15, XX
Transportation, Department of                     5, L
  Coast Guard                                     33, I; 46, I; 49, IV
  Coast Guard (Great Lakes Pilotage)              46, III
  Commercial Space Transportation                 14, III
  Contract Appeals, Board of                      48, 63
  Emergency Management and Assistance             44, IV
  Federal Acquisition Regulation                  48, 12
  Federal Aviation Administration                 14, I
  Federal Highway Administration                  23, I, II; 49, III
  Federal Railroad Administration                 49, II
  Federal Transit Administration                  49, VI
  Maritime Administration                         46, II
  National Highway Traffic Safety Administration  23, II, III; 49, V
  Research and Special Programs Administration    49, I
  Saint Lawrence Seaway Development Corporation   33, IV
  Secretary of Transportation, Office of          14, II; 49, Subtitle A

[[Page 569]]

  Surface Transportation Board                    49, X
Transportation, Office of                         7, XXXIII
Temporary Duty (TDY) Travel Allowances            41, 301
Treasury Department                               5, XXI; 17, IV
  Alcohol, Tobacco and Firearms, Bureau of        27, I
  Community Development Financial Institutions    12, XVIII
       Fund
  Comptroller of the Currency                     12, I
  Customs Service, United States                  19, I
  Engraving and Printing, Bureau of               31, VI
  Federal Acquisition Regulation                  48, 10
  Federal Law Enforcement Training Center         31, VII
  Fiscal Service                                  31, II
  Foreign Assets Control, Office of               31, V
  Internal Revenue Service                        26, I
  International Investment, Office of             31, VIII
  Monetary Offices                                31, I
  Secret Service                                  31, IV
  Secretary of the Treasury, Office of            31, Subtitle A
  Thrift Supervision, Office of                   12, V
Truman, Harry S., Scholarship Foundation          45, XVIII
United States and Canada, International Joint     22, IV
     Commission
United States and Mexico, International Boundary  22, XI
     and Water Commission, United States Section
United States Enrichment Corporation              10, XI
Utah Reclamation Mitigation and Conservation      43, III
     Commission
Veterans Affairs Department                       38, I
  Federal Acquisition Regulation                  48, 8
Veterans' Employment and Training, Office of the  41, 61; 20, IX
     Assistant Secretary for
Vice President of the United States, Office of    32, XXVIII
Vocational and Adult Education, Office of         34, IV
Wage and Hour Division                            29, V
Water Resources Council                           18, VI
Workers' Compensation Programs, Office of         20, I
World Agricultural Outlook Board                  7, XXXVIII

[[Page 571]]

                                     

                                     



                       Table of OMB Control Numbers



         PART 9--OMB APPROVALS UNDER THE PAPERWORK REDUCTION ACT

    Authority: 7 U.S.C. 135 et seq., 136-136y; 15 U.S.C. 2001, 2003, 
2005, 2006, 2601-2671; 21 U.S.C. 331j, 346a, 348; 31 U.S.C. 9701; 33 
U.S.C. 1251 et seq., 1311, 1313d, 1314, 1318, 1321, 1326, 1330, 1342, 
1344, 1345 (d) and (e), 1361; E.O. 11735, 38 FR 21243, 3 CFR, 1971-1975 
Comp. p. 973; 42 U.S.C. 241, 242b, 243, 246, 300f, 300g, 300g-1, 300g-2, 
300g-3, 300g-4, 300g-5, 300g-6, 300j-1, 300j-2, 300j-3, 300j-4, 300j-9, 
1857 et seq., 6901-6992k, 7401-7671q, 7542, 9601-9657, 11023, 11048.

Sec. 9.1  OMB approvals under the Paperwork Reduction Act.

    This part consolidates the display of control numbers assigned to 
collections of information in certain EPA regulations by the Office of 
Management and Budget (OMB) under the Paperwork Reduction Act (PRA). 
This part fulfills the requirements of section 3507(f) of the PRA.

------------------------------------------------------------------------
                                                            OMB control
                     40 CFR citation                            No.
------------------------------------------------------------------------
                           Public Information
------------------------------------------------------------------------
Part 2, subpart B.......................................       2050-0143
------------------------------------------------------------------------
    Environmental Impact Assessment of Nongovernmental Activities in
                               Antarctica
------------------------------------------------------------------------
8.5-8.10................................................       2020-0007
------------------------------------------------------------------------
   General Regulation for Assistance Programs for Other than State and
                            Local Governments
------------------------------------------------------------------------
30.400..................................................       2030-0020
30.500..................................................       2030-0020
30.501..................................................       2030-0020
30.503..................................................       2030-0020
30.505..................................................       2030-0020
30.510..................................................       2030-0020
30.520..................................................       2030-0020
30.530..................................................       2030-0020
30.531..................................................       2030-0020
30.532..................................................       2030-0020
30.535..................................................       2030-0020
30.1002.................................................       2030-0020
30.1003.................................................       2030-0020
30.1200.................................................       2030-0020
------------------------------------------------------------------------
     Uniform Administrative Requirements for Grants and Cooperative
                Agreements to State and Local Governments
------------------------------------------------------------------------
31.10...................................................       2030-0020
31.20-31.21.............................................       2030-0020
31.31-31.32.............................................       2030-0020
31.36(g)-31.36(h).......................................       2030-0020
31.40...................................................       2030-0020
31.42...................................................       2030-0020
31.6....................................................       2030-0020
------------------------------------------------------------------------
                 Procurement Under Assistance Agreements
------------------------------------------------------------------------
33.110..................................................       2030-0003
33.211..................................................       2030-0003
------------------------------------------------------------------------
                       State and Local Assistance
------------------------------------------------------------------------
35.2015.................................................       2040-0027
35.2025.................................................       2040-0027
35.2034.................................................       2040-0027
35.2040.................................................       2040-0027
35.2105-35.2107.........................................       2040-0027
35.2110.................................................       2040-0027
35.2114.................................................       2040-0027
35.2118.................................................       2040-0027
35.2120.................................................       2040-0027
35.2127.................................................       2040-0027
35.2130.................................................       2040-0027
35.2140.................................................       2040-0027
35.2211-35.2212.........................................       2040-0027
35.2215-35.2216.........................................       2040-0027
35.2218.................................................       2040-0027
35.3010.................................................       2040-0095
35.3030.................................................       2040-0095
35.3130.................................................       2040-0118
35.3135.................................................       2040-0118
35.3140.................................................       2040-0118
35.3145.................................................       2040-0118
35.3150.................................................       2040-0118
35.3155.................................................       2040-0118
35.3160.................................................       2040-0118
35.3165.................................................       2040-0118
35.3170.................................................       2040-0118
35.6055(a)(2)...........................................       2010-0020
35.6055(b)(1)...........................................       2010-0020
35.6055(b)(2)(i)-(ii)...................................       2010-0020
35.6105(a)(2)(i)-(v), (vii).............................       2010-0020
35.6110(b)(2)...........................................       2010-0020
35.6120.................................................       2010-0020
35.6145.................................................       2010-0020
35.6155(a), (c).........................................       2010-0020
35.6230(a), (c).........................................       2010-0020
35.6300(a)(3)...........................................       2010-0020
35.6315(c)..............................................       2010-0020
35.6320.................................................       2010-0020
35.6340(a)..............................................       2010-0020

[[Page 572]]

35.6350.................................................       2010-0020
35.6500.................................................       2010-0020
35.6550(a)(1)(ii).......................................       2010-0020
35.6550(b)(1)(iii)......................................       2010-0020
35.6550(b)(2)(i)........................................       2010-0020
35.6585.................................................       2010-0020
35.6595(a)..............................................       2010-0020
35.6600(a)..............................................       2010-0020
35.6650.................................................       2010-0020
35.6655.................................................       2010-0020
35.6660.................................................       2010-0020
35.6665(a)..............................................       2010-0020
35.6700.................................................       2010-0020
35.6705.................................................       2010-0020
35.6710.................................................       2010-0020
35.6805.................................................       2010-0020
35.6815(a), (d), (e)....................................       2010-0020
35.9000-35.9070.........................................       2040-0138
------------------------------------------------------------------------
           Indian Tribes: Air Quality Planning and Management
------------------------------------------------------------------------
49.6....................................................       2060-0306
49.7....................................................       2060-0306
------------------------------------------------------------------------
 Requirements for Preparation, Adoption, and Submittal of Implementation
                                  Plans
------------------------------------------------------------------------
51.160-51.166...........................................       2060-0003
51.321-51.323...........................................       2060-0088
51.353-51.354...........................................       2060-0252
51.365-51.366...........................................       2060-0252
51.370-51.371...........................................       2060-0252
51.850-51.860...........................................       2060-0279
------------------------------------------------------------------------
            Approval and Promulgation of Implementation Plans
------------------------------------------------------------------------
52.21...................................................       2060-0003
52.741..................................................       2060-0203
------------------------------------------------------------------------
                 Outer Continental Shelf Air Regulations
------------------------------------------------------------------------
55.4-55.8...............................................       2060-0249
55.11-55.14.............................................       2060-0249
------------------------------------------------------------------------
                    Ambient Air Quality Surveillance
------------------------------------------------------------------------
58.11-58.14.............................................       2060-0084
58.20-58.23.............................................       2060-0084
58.25-58.28.............................................       2060-0084
58.30-58.31.............................................       2060-0084
58.33...................................................       2060-0084
58.35...................................................       2060-0084
58.40-58.41.............................................       2060-0084
58.43...................................................       2060-0084
58.45...................................................       2060-0084
58.50...................................................       2060-0084
------------------------------------------------------------------------
         Standards of Performance for New Stationary Sources \1\
------------------------------------------------------------------------
60.7(d).................................................       2060-0207
60.45-60.47.............................................       2060-0026
60.46a-60.49a...........................................       2060-0023
60.40b..................................................       2060-0072
60.42b..................................................       2060-0072
60.44b-60.49b...........................................       2060-0072
60.42c..................................................       2060-0202
60.44c-60.48c...........................................       2060-0202
60.53-60.54.............................................       2060-0040
60.50a..................................................       2060-0210
60.56a-60.59a...........................................       2060-0210
60.63-60.65.............................................       2060-0025
60.73-60.74.............................................       2060-0019
60.84-60.85.............................................       2060-0041
60.93...................................................       2060-0083
60.104-60.108...........................................       2060-0022
60.113a-60.115a.........................................       2060-0121
60.113b-60.116b.........................................       2060-0074
60.123..................................................       2060-0080
60.133..................................................       2060-0110
60.142-60.144...........................................       2060-0029
60.143a-60.145a.........................................       2060-0029
60.153-60.155...........................................       2060-0035
60.192(b)...............................................       2060-0031
60.194-60.195...........................................       2060-0031
60.203-60.204...........................................       2060-0037
60.213-60.214...........................................       2060-0037
60.223-60.224...........................................       2060-0037
60.233-60.234...........................................       2060-0037
60.243-60.244...........................................       2060-0037
60.253-60.254...........................................       2060-0122
60.273-60.276...........................................       2060-0038
60.273a-60.276a.........................................       2060-0038
60.284-60.286...........................................       2060-0021
60.292-60.293...........................................       2060-0054
60.296..................................................       2060-0054
60.303..................................................       2060-0082
60.310..................................................       2060-0106
60.313-60.316...........................................       2060-0106
60.334-60.335...........................................       2060-0028
60.343-60.344...........................................       2060-0063
60.373-60.374...........................................       2060-0081
60.384-60.386...........................................       2060-0016
60.393-60.396...........................................       2060-0034
60.398..................................................       2060-0034
60.403-60.404...........................................       2060-0111
60.433-60.435...........................................       2060-0105
60.443-60.447...........................................       2060-0004
60.453-60.456...........................................       2060-0108
60.463-60.466...........................................       2060-0107
60.473-60.474...........................................       2060-0002
60.482-2................................................       2060-0012
60.482-3................................................       2060-0012
60.482-4................................................       2060-0012
60.482-7................................................       2060-0012
60.482-8................................................       2060-0012
60.482-10...............................................       2060-0012
60.483-1................................................       2060-0012
60.483-2................................................       2060-0012
60.484-60.487...........................................       2060-0012
60.493-60.496...........................................       2060-0001
60.502-60.503...........................................       2060-0006
60.505..................................................       2060-0006
60.530-60.536...........................................       2060-0161
60.537(a)(1)-(2), (a)(4)-(5), (b)-(i)...................       2060-0161
60.538-60.539...........................................       2060-0161
60.543(b)(2)-(4), (c)-(n)...............................       2060-0156
60.544..................................................       2060-0156
60.545(a)-(d), (f)......................................       2060-0156
60.546(a)-(e), (f)(4)-(6), (g)-(j)......................       2060-0156
60.547..................................................       2060-0156
60.562-1................................................       2060-0145
60.562-2................................................       2060-0145
60.563-60.565...........................................       2060-0145
60.580..................................................       2060-0073
60.583-60.585...........................................       2060-0073
60.592-60.593...........................................       2060-0067
60.603-60.604...........................................       2060-0059
60.613-60.615...........................................       2060-0197
60.622..................................................       2060-0079
60.624-60.625...........................................       2060-0079
60.632-60.636...........................................       2060-0120
60.640..................................................       2060-0120
60.642-60.644...........................................       2060-0120
60.646-60.647...........................................       2060-0120
60.663-60.665...........................................       2060-0197
60.670..................................................       2060-0050
60.672..................................................       2060-0050

[[Page 573]]

60.674-60.676...........................................       2060-0050
60.683-60.685...........................................       2060-0114
60.692-1................................................       2060-0172
60.692-2................................................       2060-0172
60.692-3................................................       2060-0172
60.692-4................................................       2060-0172
60.692-5................................................       2060-0172
60.693-1................................................       2060-0172
60.693-2................................................       2060-0172
60.695-60.698...........................................       2060-0172
60.703-60.705...........................................       2060-0269
60.710..................................................       2060-0171
60.713-60.717...........................................       2060-0171
60.722-60.725...........................................       2060-0162
60.734-60.736...........................................       2060-0251
60.740..................................................       2060-0181
60.743-60.747...........................................       2060-0181
------------------------------------------------------------------------
      National Emission Standards for Hazardous Air Pollutants \2\
------------------------------------------------------------------------
61.24-61.25.............................................       2060-0191
61.32-61.34.............................................       2060-0092
61.53-61.55.............................................       2060-0097
61.65(b)-(d)............................................       2060-0071
61.67-61.71.............................................       2060-0071
61.93-61.95.............................................       2060-0191
61.103-61.105...........................................       2060-0191
61.107..................................................       2060-0191
61.123-61.124...........................................       2060-0191
61.126..................................................       2060-0191
61.132-61.133...........................................       2060-0185
61.135-61.139...........................................       2060-0185
61.142..................................................       2060-0101
61.144-61.147...........................................       2060-0101
61.149..................................................       2060-0101
61.150-61.155...........................................       2060-0101
61.163-61.165...........................................       2060-0043
61.203..................................................       2060-0191
61.206-61.209...........................................       2060-0191
61.223-61.224...........................................       2060-0191
61.242-1................................................       2060-0068
61.242-2................................................       2060-0068
61.242-3................................................       2060-0068
61.242-4................................................       2060-0068
61.242-7................................................       2060-0068
61.242-8................................................       2060-0068
61.242-10...............................................       2060-0068
61.242-11...............................................       2060-0068
61.243-1................................................       2060-0068
61.243-2................................................       2060-0068
61.244-61.247...........................................       2060-0068
61.253-61.255...........................................       2060-0191
61.271-61.276...........................................       2060-0185
61.300..................................................       2060-0182
61.302-61.305...........................................       2060-0182
61.342..................................................       2060-0183
61.344-61.349...........................................       2060-0183
61.354-61.357...........................................       2060-0183
------------------------------------------------------------------------
   National Emission Standards for Hazardous Air Pollutants for Source
                             Categories \3\
------------------------------------------------------------------------
63.5(d).................................................       2060-0330
63.52-63.56.............................................       2060-0266
63.72...................................................       2060-0222
63.74-63.79.............................................       2060-0222
63.91-63.96.............................................       2060-0264
63.103..................................................       2060-0282
63.105..................................................       2060-0282
63.117-63.118...........................................       2060-0282
63.122-63.123...........................................       2060-0282
63.129-63.130...........................................       2060-0282
63.146-63.148...........................................       2060-0282
63.151-63.152...........................................       2060-0282
63.181-63.182...........................................       2060-0282
63.302-63.311...........................................       2060-0253
63.322-63.325...........................................       2060-0234
63.345-63.347...........................................       2060-0327
63.363-63.367...........................................       2060-0283
63.403-63.406...........................................       2060-0268
63.420..................................................       2060-0325
63.422-63.428...........................................       2060-0325
63.467-63.468...........................................       2060-0273
63.480-63.506...........................................       2060-0356
63.525-63.528...........................................       2060-0290
63.548-63.550...........................................       2060-0296
63.563-63.567...........................................       2060-0289
63.653..................................................       2060-0340
63.654..................................................       2060-0340
63.703-63.707...........................................       2060-0326
63.752-63.753...........................................       2060-0314
63.787(a)-(b)...........................................       2060-0330
63.788(a)-(c)...........................................       2060-0330
63.806-63.807...........................................       2060-0324
63.829-63.830...........................................       2060-0335
63.846(d)...............................................       2060-0360
63.847(b), (g)..........................................       2060-0360
63.848(d)(5), (e), (f)(5)(ii), (g), (k), (m)............       2060-0360
63.850..................................................       2060-0360
63.1311.................................................       2060-0351
63.1314.................................................       2060-0351
63.1315.................................................       2060-0351
63.1319.................................................       2060-0351
63.1320.................................................       2060-0351
63.1325-63.1332.........................................       2060-0351
63.1335.................................................       2060-0351
------------------------------------------------------------------------
                 Chemical Accident Prevention Provisions
------------------------------------------------------------------------
68.120(a), (e), and (g).................................       2050-0127
------------------------------------------------------------------------
                     State Operating Permit Programs
------------------------------------------------------------------------
70.3-70.11..............................................       2060-0243
------------------------------------------------------------------------
                    Federal Operating Permit Programs
------------------------------------------------------------------------
71.5....................................................       2060-0336
71.6(a),(c),(d),(g).....................................       2060-0336
71.7....................................................       2060-0336
71.9(e)-(j).............................................       2060-0336
71.24-71.26.............................................       2060-0276
------------------------------------------------------------------------
                           Permits Regulation
------------------------------------------------------------------------
72.7-72.10..............................................       2060-0258
72.14...................................................       2060-0258
72.20-72.25.............................................       2060-0258
72.30-72.33.............................................       2060-0258
72.40-72.44.............................................       2060-0258
72.50-72.51.............................................       2060-0258
72.60-72.69.............................................       2060-0258
72.70-72.74.............................................       2060-0258
72.80-72.85.............................................       2060-0258
72.90-72.96.............................................       2060-0258
------------------------------------------------------------------------
                            Allowance System
------------------------------------------------------------------------
73.10-73.13.............................................       2060-0261
73.16...................................................       2060-0261
73.18-73.21.............................................       2060-0261
73.30-73.38.............................................       2060-0258
73.50-73.53.............................................       2060-0258
73.70-73.77.............................................       2060-0221
73.80-73.86.............................................       2060-0258
73.90...................................................       2060-0258
------------------------------------------------------------------------

[[Page 574]]

                         Sulfur Dioxide Opt-ins
------------------------------------------------------------------------
74.12...................................................       2060-0258
74.14...................................................       2060-0258
74.16...................................................       2060-0258
74.18...................................................       2060-0258
74.20...................................................       2060-0258
74.22...................................................       2060-0258
74.24-74.25.............................................       2060-0258
74.41...................................................       2060-0258
74.43-74.44.............................................       2060-0258
74.46-74.47.............................................       2060-0258
74.60-74.64.............................................       2060-0258
------------------------------------------------------------------------
                     Continuous Emission Monitoring
------------------------------------------------------------------------
75.4-75.5...............................................       2060-0258
75.10-75.18.............................................       2060-0258
75.20-75.24.............................................       2060-0258
75.30-75.34.............................................       2060-0258
75.40-75.48.............................................       2060-0258
75.50-75.52.............................................       2060-0258
75.53-75.56.............................................       2060-0258
75.60-75.67.............................................       2060-0258
------------------------------------------------------------------------
               Nitrogen Oxides Emission Reduction Program
------------------------------------------------------------------------
76.8-76.15..............................................       2060-0258
------------------------------------------------------------------------
                            Excess Emissions
------------------------------------------------------------------------
77.3-77.6...............................................       2060-0258
------------------------------------------------------------------------
                 Appeal Procedures for Acid Rain Program
------------------------------------------------------------------------
78.1-78.20..............................................       2060-0258
------------------------------------------------------------------------
                Registration of Fuels and Fuel Additives
------------------------------------------------------------------------
79.10-79.11.............................................       2060-0150
79.20-79.21.............................................       2060-0150
79.31-79.33.............................................       2060-0150
79.51(a), (c), (d), (g), (h)............................       2060-0150
79.52...................................................       2060-0150
79.57(a)(5).............................................       2060-0150
79.57(f)(5).............................................       2060-0150
79.58(e)................................................       2060-0150
79.59(b)-(d)............................................       2060-0150
79.60...................................................       2060-0150
79.61(e)................................................       2060-0150
79.62-79.68.............................................       2060-0297
------------------------------------------------------------------------
                 Regulation of Fuels and Fuel Additives
------------------------------------------------------------------------
80.20...................................................       2060-0066
80.25...................................................       2060-0066
80.27...................................................       2060-0178
80.29(c)................................................       2060-0308
80.40...................................................       2060-0277
80.46...................................................       2060-0277
80.65...................................................       2060-0277
80.68-80.69.............................................       2060-0277
80.74-80.77.............................................       2060-0277
80.79...................................................       2060-0277
80.83...................................................       2060-0277
80.91-80.93.............................................       2060-0277
80.91-80.94.............................................       2060-0277
80.101-80.106...........................................       2060-0277
80.125..................................................       2060-0277
80.127-80.130...........................................       2060-0277
80.128-80.130...........................................       2060-0277
80.141(c)-(f)...........................................       2060-0275
80.157..................................................       2060-0275
80.158..................................................       2060-0275
80.160..................................................       2060-0275
80.161..................................................       2060-0275
80.162..................................................       2060-0275
80.163(d)(3)............................................       2060-0275
80.164..................................................       2060-0275
80.165..................................................       2060-0275
80.166..................................................       2060-0275
80.167(d)...............................................       2060-0275
80.170..................................................       2060-0275
80.171..................................................       2060-0275
80.173..................................................       2060-0275
------------------------------------------------------------------------
                    Protection of Stratospheric Ozone
------------------------------------------------------------------------
82.9-82.13..............................................       2060-0170
82.21...................................................       2060-0170
82.36...................................................       2060-0247
82.38...................................................       2060-0247
82.40...................................................       2060-0247
82.42...................................................       2060-0247
82.122..................................................       2060-0259
82.156..................................................       2060-0256
82.160-82.162...........................................       2060-0256
82.164..................................................       2060-0256
82.166..................................................       2060-0256
82.176(a)...............................................       2060-0226
82.176(c)(3)............................................       2060-0226
82.178..................................................       2060-0226
82.180..................................................       2060-0350
82.180(a)(5)............................................       2060-0226
82.180(b)(3)............................................       2060-0226
82.184(c)...............................................       2060-0226
82.184(e)...............................................       2060-0226
------------------------------------------------------------------------
 Control of Air Pollution From Motor Vehicles and Motor Vehicle Engines
------------------------------------------------------------------------
85.503..................................................       2060-0104
85.505..................................................       2060-0104
85.1403.................................................       2060-0302
85.1404.................................................       2060-0302
85.1406.................................................       2060-0302
85.1407.................................................       2060-0302
85.1408.................................................       2060-0302
85.1409.................................................       2060-0302
85.1410.................................................       2060-0302
85.1411.................................................       2060-0302
85.1412.................................................       2060-0302
85.1413.................................................       2060-0302
85.1414.................................................       2060-0302
85.1415.................................................       2060-0302
85.1503-85.1507.........................................       2060-0095
85.1509-85.1510.........................................       2060-0095
85.1511(b)-(d), (f).....................................       2060-0095
85.1511(b)(3)...........................................       2060-0007
85.1512.................................................       2060-0095
85.1514-85.1515.........................................       2060-0095
85.1703.................................................       2060-0124
85.1705-85.1706.........................................       2060-0007
85.1901-85.1909.........................................       2060-0048
85.2112-85.2123.........................................       2060-0065
85.2114.................................................       2060-0016
85.2115.................................................       2060-0016
------------------------------------------------------------------------
 Control of Air Pollution From New and In-Use Motor Vehicles and New and
     In-Use Motor Vehicle Engines: Certification and Test Procedures
------------------------------------------------------------------------
86.004-38...............................................       2060-0104
86.004-40...............................................       2060-0104
86.079-31--86.079-33....................................       2060-0104
86.079-36...............................................       2060-0104
86.079-39...............................................       2060-0104
86.080-12...............................................       2060-0104

[[Page 575]]

86.082-34...............................................       2060-0104
86.085-13...............................................       2060-0104
86.085-37...............................................       2060-0104
86.087-38...............................................       2060-0104
86.090-14...............................................       2060-0104
86.090-21...............................................       2060-0104
86.090-25...............................................       2060-0104
86.090-26...............................................       2060-0104
86.090-27...............................................       2060-0104
86.091-7................................................       2060-0104
86.091-15...............................................       2060-0104
86.091-21...............................................       2060-0104
86.091-23...............................................       2060-0104
86.091-28...............................................       2060-0104
86.091-30...............................................       2060-0104
86.092-14...............................................       2060-0104
86.092-15...............................................       2060-0104
86.092-23...............................................       2060-0104
86.092-24...............................................       2060-0104
86.092-26...............................................       2060-0104
86.092-35...............................................       2060-0104
86.094-7-86.094-9.......................................       2060-0104
86.094-15-86.094-16.....................................       2060-0104
86.094-17...............................................       2060-0104
86.094-18...............................................       2060-0104
86.094-21...............................................       2060-0104
86.094-23...............................................       2060-0104
86.094-24(a)(3)(iii)....................................       2060-0314
86.094-25...............................................       2060-0104
86.094-30...............................................       2060-0104
86.094-35...............................................       2060-0104
86.095-14...............................................       2060-0104
86.095-23...............................................       2060-0104
86.095-24...............................................       2060-0104
86.095-26...............................................       2060-0104
86.095-30...............................................       2060-0104
86.095-35...............................................       2060-0104
86.094-38...............................................       2060-0104
86.096-7................................................       2060-0104
86.096-8................................................       2060-0104
86.096-9................................................       2060-0104
86.096-10...............................................       2060-0104
86.096-14...............................................       2060-0104
86.096-21...............................................       2060-0104
86.096-23...............................................       2060-0104
86.096-24...............................................       2060-0104
86.096-26...............................................       2060-0104
86.096-30...............................................       2060-0104
86.096-35...............................................       2060-0104
86.097-9................................................       2060-0104
86.098-23...............................................       2060-0104
86.098-28...............................................       2060-0104
86.099-8................................................       2060-0104
86.099-9................................................       2060-0104
86.099-10...............................................       2060-0104
86.111-94...............................................       2060-0104
86.113-82...............................................       2060-0104
86.113-87...............................................       2060-0104
86.113-90...............................................       2060-0104
86.113-91...............................................       2060-0104
86.113-94...............................................       2060-0104
86.135-82...............................................       2060-0104
86.135-90...............................................       2060-0104
86.135-94...............................................       2060-0104
86.142-90...............................................       2060-0104
86.144-90...............................................       2060-0104
86.144-94...............................................       2060-0104
86.150-98...............................................       2060-0104
86.336-79...............................................       2060-0104
86.337-79...............................................       2060-0104
86.412-78...............................................       2060-0104
86.414-78...............................................       2060-0104
86.415-78...............................................       2060-0104
86.416-80...............................................       2060-0104
86.421-78...............................................       2060-0104
86.423-78...............................................       2060-0104
86.427-78...............................................       2060-0104
86.428-80...............................................       2060-0104
86.429-78...............................................       2060-0104
86.431-78...............................................       2060-0104
86.432-78...............................................       2060-0104
86.434-78...............................................       2060-0104
86.435-78...............................................       2060-0104
86.436-78...............................................       2060-0104
86.437-78...............................................       2060-0104
86.438-78...............................................       2060-0104
86.439-78...............................................       2060-0104
86.440-78...............................................       2060-0104
86.513-94...............................................       2060-0104
86.537-90...............................................       2060-0104
86.542-90...............................................       2060-0104
86.603-88...............................................       2060-0064
86.604-84...............................................       2060-0064
86.605-88...............................................       2060-0064
86.606-84...............................................       2060-0064
86.607-84...............................................       2060-0064
86.608-88...............................................       2060-0064
86.608-90...............................................       2060-0064
86.608-96...............................................       2060-0104
86.609-84...............................................       2060-0064
86.609-96...............................................       2060-0104
86.612-84...............................................       2060-0064
86.614-84...............................................       2060-0064
86.615-84...............................................       2060-0064
86.709-94...............................................       2060-0104
86.709-99...............................................       2060-0104
86.884-5................................................       2060-0104
86.884-7................................................       2060-0104
86.884-9................................................       2060-0104
86.884-10...............................................       2060-0104
86.884-12...............................................       2060-0104
86.884-13...............................................       2060-0104
86.1003-90..............................................       2060-0064
86.1004-84..............................................       2060-0064
86.1005-90..............................................       2060-0064
86.1006-84..............................................       2060-0064
86.1007-84..............................................       2060-0064
86.1008-90..............................................       2060-0064
86.1008-96..............................................       2060-0104
86.1009-84..............................................       2060-0064
86.1009-96..............................................       2060-0104
86.1012-84..............................................       2060-0064
86.1014-84..............................................       2060-0064
86.1015-87..............................................       2060-0064
86.1106-87..............................................       2060-0132
86.1108-87..............................................       2060-0132
86.1110-87..............................................       2060-0132
86.1111-87..............................................       2060-0104
86.1112-87-86.1115-87...................................       2060-0132
86.1213-85..............................................       2060-0104
86.1213-87..............................................       2060-0104
86.1242-85..............................................       2060-0104
86.1242-90..............................................       2060-0104
86.1308-84..............................................       2060-0104
86.1310-90..............................................       2060-0104
86.1311-94..............................................       2060-0104
86.1313-84..............................................       2060-0104
86.1313-87..............................................       2060-0104
86.1313-90..............................................       2060-0104
86.1313-91..............................................       2060-0104
86.1313-94..............................................       2060-0104
86.1313-98..............................................       2060-0104
86.1314-84..............................................       2060-0104
86.1316-84..............................................       2060-0104
86.1316-90..............................................       2060-0104
86.1319-84..............................................       2060-0104

[[Page 576]]

86.1319-90..............................................       2060-0104
86.1321-84..............................................       2060-0104
86.1321-90..............................................       2060-0104
86.1323-84..............................................       2060-0104
86.1327-84..............................................       2060-0104
86.1327-88..............................................       2060-0104
86.1327-90..............................................       2060-0104
86.1327-98..............................................       2060-0104
86.1332-84..............................................       2060-0104
86.1332-90..............................................       2060-0104
86.1334-84..............................................       2060-0104
86.1335-90..............................................       2060-0104
86.1336-84..............................................       2060-0104
86.1340-84..............................................       2060-0104
86.1340-90..............................................       2060-0104
86.1341-90..............................................       2060-0104
86.1341-98..............................................       2060-0104
86.1342-90..............................................       2060-0104
86.1344-94..............................................       2060-0104
86.1413.................................................       2060-0104
86.1427.................................................       2060-0104
86.1432.................................................       2060-0104
86.1434.................................................       2060-0104
86.1437.................................................       2060-0104
86.1442.................................................       2060-0104
86.1542-84..............................................       2060-0104
86.1544-84..............................................       2060-0104
86.1705.................................................       2060-0345
86.1707.................................................       2060-0345
86.1708.................................................       2060-0345
86.1709.................................................       2060-0345
86.1710.................................................       2060-0345
86.1712.................................................       2060-0345
86.1713.................................................       2060-0345
86.1714.................................................       2060-0345
86.1717.................................................       2060-0345
86.1721.................................................       2060-0345
86.1723.................................................       2060-0345
86.1724.................................................       2060-0345
86.1725.................................................       2060-0345
86.1726.................................................       2060-0345
86.1728.................................................       2060-0345
86.1734.................................................       2060-0345
86.1735.................................................       2060-0345
86.1770.................................................       2060-0345
86.1771.................................................       2060-0345
86.1776.................................................       2060-0345
86.1777.................................................       2060-0345
86.1778.................................................       2060-0345
86.2500.................................................       2060-0104
------------------------------------------------------------------------
                           Clean-Fuel Vehicles
------------------------------------------------------------------------
88.104-94(a), (c), (e), (f), (g), (h), (i), (j), (k)....       2060-0104
88.105-94...............................................       2060-0104
88.204-94(b)(1).........................................       2060-0314
88.204-94(c)............................................       2060-0314
88.305-94...............................................       2060-0104
88.306-94(a), (b) introductory text.....................       2060-0104
88.306-94(b)(1).........................................       2060-0314
88.306-94(b)(2).........................................       2060-0314
88.306-94(b)(4).........................................       2060-0314
88.306-94(c)............................................       2060-0314
88.306-94(f)............................................       2060-0314
------------------------------------------------------------------------
        Control of Emissions From New and In-Use Nonroad Engines
------------------------------------------------------------------------
89.1....................................................       2060-0124
89.2....................................................       2060-0124
89.114-96-89.120-96.....................................       2060-0287
89.122-96-89.127-96.....................................       2060-0287
89.129-96...............................................       2060-0287
89.203-96-89.207-96.....................................       2060-0287
89.209-96-89.211-96.....................................       2060-0287
89.304-96-89.331-96.....................................       2060-0287
89.404-96-89.424-96.....................................       2060-0287
89.505-89.905...........................................       2060-0064
89.511..................................................       2060-0064
89.512..................................................       2060-0064
89.603-89.605...........................................       2060-0095
89.607-89.610...........................................       2060-0095
89.611..................................................      2060-0007,
                                                               2060-0095
89.612..................................................       2060-0095
89.801..................................................       2060-0048
89.803..................................................       2060-0048
89.903..................................................       2060-0048
89.905..................................................       2060-0007
89.906..................................................       2060-0007
------------------------------------------------------------------------
        Control of Emissions From New and In-use Nonroad Engines
------------------------------------------------------------------------
90.107-90.108...........................................       2060-0338
90.113..................................................       2060-0338
90.115-90.124...........................................       2060-0338
90.126..................................................       2060-0338
90.304-90.329...........................................       2060-0338
90.404-90.427...........................................       2060-0338
90.505-90.509...........................................       2060-0295
90.511-90.512...........................................       2060-0295
90.604..................................................       2060-0294
90.611-90.613...........................................       2060-0294
90.800..................................................       2060-0048
90.802-90.804...........................................       2060-0048
90.806..................................................       2060-0048
90.903..................................................       2060-0124
90.905-90.906...........................................       2060-0007
------------------------------------------------------------------------
      Determining Conformity of Federal Actions to State or Federal
                          Implementation Plans
------------------------------------------------------------------------
93.150-93.160...........................................       2060-0279
------------------------------------------------------------------------
                        Mandatory Patent Licenses
------------------------------------------------------------------------
95.2....................................................       2060-0307
------------------------------------------------------------------------
                        Oil Pollution Prevention
------------------------------------------------------------------------
112.1-112.7.............................................       2050-0021
------------------------------------------------------------------------
 Oil Pollution Prevention; Non-Transportation-Related Onshore Facilities
------------------------------------------------------------------------
112.20..................................................       2050-0135
------------------------------------------------------------------------
   Designation, Reportable Quantities, and Notification for Hazardous
                               Substances
------------------------------------------------------------------------
116.4...................................................       2050-0046
117.3...................................................       2050-0046
117.21..................................................       2050-0046
------------------------------------------------------------------------
   EPA Administered Permit Programs: The National Pollutant Discharge
                           Elimination System
------------------------------------------------------------------------
122.21(f)-(l)...........................................      2040-0086,
                                                               2040-0170
122.21(j)(4)............................................       2040-0150
122.21(m)-(p)...........................................      2040-0068,
                                                               2040-0170
122.26(c), (d)..........................................       2040-0086
122.41(h)...............................................      2040-0068,
                                                               2040-0170

[[Page 577]]

122.41(j)...............................................      2040-0009,
                                                              2040-0110,
                                                               2040-0170
122.41(l)...............................................      2040-0110,
                                                              2040-0068,
                                                               2040-0170
122.42(c)...............................................       2040-0086
122.42(a), (b), (l).....................................      2040-0068,
                                                               2040-0170
122.44(g), (i)..........................................      2040-0004,
                                                              2040-0170,
                                                               2040-0110
122.44(r)...............................................       2040-0180
122.45(b)...............................................      2040-0004,
                                                               2040-0110
122.45(b)(4)............................................       2040-0068
122.47(a)...............................................      2040-0110,
                                                               2040-0170
122.47(b)...............................................      2040-0110,
                                                              2040-0068,
                                                               2040-0170
122.48..................................................      2040-0004,
                                                               2040-0170
122.62(a)...............................................      2040-0068,
                                                               2040-0170
122.63..................................................      2040-0068,
                                                               2040-0170
------------------------------------------------------------------------
                        State Permit Requirements
------------------------------------------------------------------------
123.21-123.24...........................................      2040-0057,
                                                               2040-0170
123.25..................................................      2040-0004,
                                                              2040-0110,
                                                              2040-0170,
                                                               2040-0180
123.26-123.29...........................................      2040-0057,
                                                               2040-0170
123.43..................................................      2040-0057,
                                                               2040-0170
123.44..................................................      2040-0057,
                                                              2040-0170,
                                                               2040-0180
123.45..................................................      2040-0057,
                                                               2040-0170
123.62..................................................      2040-0057,
                                                              2040-0170,
                                                               2040-0180
123.63..................................................      2040-0057,
                                                              2040-0170,
                                                               2040-0180
123.64..................................................      2040-0057,
                                                               2040-0170
------------------------------------------------------------------------
                      Procedures for Decisionmaking
------------------------------------------------------------------------
124.5...................................................       2040-0068
124.31..................................................       2050-0149
124.32..................................................       2050-0149
124.33..................................................       2050-0149
124.53-124.54...........................................       2040-0057
------------------------------------------------------------------------
 Criteria and Standards for the National Pollutant Discharge Elimination
                                 System
------------------------------------------------------------------------
125.59-125.67, and appendix A and B.....................       2040-0088
------------------------------------------------------------------------
                  Water Quality Planning and Management
------------------------------------------------------------------------
130.6-130.10............................................       2040-0071
130.15..................................................       2040-0071
------------------------------------------------------------------------
                   Water Quality Standards Regulation
------------------------------------------------------------------------
131.1...................................................       2040-0180
131.5...................................................       2040-0180
131.6-131.8.............................................       2040-0049
131.20..................................................       2040-0049
131.21..................................................      2040-0049,
                                                               2040-0180
131.22..................................................       2040-0049
131.31-131.36...........................................       2040-0049
------------------------------------------------------------------------
            Water Quality Guidance for the Great Lakes System
------------------------------------------------------------------------
132.1...................................................       2040-0180
132.2...................................................       2040-0180
132.3...................................................       2040-0180
132.4...................................................       2040-0180
132.5...................................................       2040-0180
Part 132, appendix A....................................       2040-0180
Part 132, appendix B....................................       2040-0180
Part 132, appendix C....................................       2040-0180
Part 132, appendix D....................................       2040-0180
Part 132, appendix E....................................       2040-0180
Part 132, appendix F....................................       2040-0180
------------------------------------------------------------------------
                    Marine Sanitation Device Standard
------------------------------------------------------------------------
Part 140................................................       2040-0187
------------------------------------------------------------------------
               National Primary Drinking Water Regulations
------------------------------------------------------------------------
141.2...................................................       2040-0090
141.4...................................................       2040-0090
141.11-141.15...........................................       2040-0090
141.21-141.22...........................................       2040-0090
141.23-141.24...........................................       2040-0090
141.25-141.30...........................................       2040-0090
141.31-141.32...........................................       2040-0090
141.33-141.35...........................................       2040-0090
141.40..................................................       2040-0090
141.41-141.43...........................................       2040-0090
141.50-141.52...........................................       2040-0090
141.60-141.63...........................................       2040-0090
141.70-141.75...........................................       2040-0090
141.80-141.91...........................................       2040-0090
141.100.................................................       2040-0090
141.110-141.111.........................................       2040-0090
141.140-141.144.........................................       2040-0183
------------------------------------------------------------------------
       National Primary Drinking Water Regulations Implementation
------------------------------------------------------------------------
142.2-142.3.............................................       2040-0090
142.10-142.15...........................................       2040-0090
142.16..................................................       2060-0090
142.17-142.24...........................................       2040-0090
142.56-142.57...........................................       2040-0090
142.60-142.61...........................................       2040-0090
142.62..................................................       2040-0090
142.63-142.64...........................................       2040-0090
142.70-142.78...........................................       2040-0090
142.81-142.81...........................................       2040-0090
------------------------------------------------------------------------
                  Underground Injection Control Program
------------------------------------------------------------------------
144.8...................................................       2040-0042
144.12..................................................       2040-0042
144.14-144.15...........................................       2040-0042
144.23..................................................       2040-0042
144.25-144.28...........................................       2040-0042
144.31-144.33...........................................       2040-0042
144.38..................................................       2040-0042
144.41..................................................       2040-0042
144.51-144.55...........................................       2040-0042

[[Page 578]]

144.62-144.66...........................................       2040-0042
144.70..................................................       2040-0042
------------------------------------------------------------------------
      Underground Injection Control Program: Criteria and Standards
------------------------------------------------------------------------
146.10..................................................       2040-0042
146.12-146.15...........................................       2040-0042
146.22-146.25...........................................       2040-0042
146.32-146.35...........................................       2040-0042
146.52..................................................       2040-0042
146.64..................................................       2040-0042
146.66-146.73...........................................       2040-0042
------------------------------------------------------------------------
              State Underground Injection Control Programs
------------------------------------------------------------------------
147.104.................................................       2040-0042
147.304-147.305.........................................       2040-0042
147.504.................................................       2040-0042
147.754.................................................       2040-0042
147.904.................................................       2040-0042
147.1154................................................       2040-0042
147.1354-147.1355.......................................       2040-0042
147.1454................................................       2040-0042
147.1654................................................       2040-0042
147.1954................................................       2040-0042
147.2103-147.2104.......................................       2040-0042
147.2154................................................       2040-0042
147.2402................................................       2040-0042
147.2905................................................       2040-0042
147.2912-147.2913.......................................       2040-0042
147.2915................................................       2040-0042
147.2918................................................       2040-0042
147.2920-147.2926.......................................       2040-0042
147.2929................................................       2040-0042
147.3002-147.3003.......................................       2040-0042
147.3006-147.3007.......................................       2040-0042
147.3011................................................       2040-0042
147.3014-147.3016.......................................       2040-0042
147.3101................................................       2040-0042
147.3104-147.3105.......................................       2040-0042
147.3107-147.3109.......................................       2040-0042
------------------------------------------------------------------------
                 Hazardous Waste Injection Restrictions
------------------------------------------------------------------------
148.5...................................................       2040-0042
148.20-148.23...........................................       2040-0042
------------------------------------------------------------------------
          Pesticide Registration and Classification Procedures
------------------------------------------------------------------------
152.46..................................................       2070-0060
152.50..................................................      2070-0024,
                                                              2070-0040,
                                                               2070-0060
152.80..................................................      2070-0040,
                                                               2070-0060
152.85..................................................      2070-0040,
                                                               2070-0060
152.98..................................................       2070-0060
152.122.................................................       2070-0060
152.132.................................................       2070-0044
152.135.................................................       2070-0060
152.164.................................................       2070-0060
152.404.................................................      2070-0040,
                                                               2070-0060
152.406.................................................      2070-0040,
                                                               2070-0060
152.412.................................................      2070-0040,
                                                               2070-0060
152.414.................................................      2070-0040,
                                                               2070-0060
------------------------------------------------------------------------
                         Registration Standards
------------------------------------------------------------------------
155.30..................................................       2070-0057
------------------------------------------------------------------------
            Labeling Requirements for Pesticides and Devices
------------------------------------------------------------------------
156.36..................................................       2070-0052
156.206.................................................       2070-0060
156.208.................................................       2070-0060
156.210.................................................       2070-0060
156.212.................................................       2070-0060
------------------------------------------------------------------------
            Packaging Requirements for Pesticides and Devices
------------------------------------------------------------------------
157.22..................................................       2070-0052
157.24..................................................       2070-0052
157.34..................................................       2070-0052
157.36..................................................       2070-0052
------------------------------------------------------------------------
                   Data Requirements for Registration
------------------------------------------------------------------------
158.30..................................................      2070-0040,
                                                              2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.32..................................................      2070-0040,
                                                              2070-0053,
                                                              2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.34..................................................      2070-0040,
                                                              2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.45..................................................      2070-0040,
                                                              2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.75..................................................      2070-0040,
                                                              2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.101.................................................      2070-0040,
                                                              2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.155.................................................      2070-0040,
                                                              2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.160.................................................      2070-0040,
                                                              2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.162.................................................      2070-0040,
                                                              2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.165.................................................      2070-0040,
                                                              2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.167.................................................      2070-0040,
                                                              2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.170.................................................      2070-0040,
                                                              2070-0057,
                                                              2070-0060,
                                                               2070-0107

[[Page 579]]

158.175.................................................      2070-0040,
                                                              2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.180.................................................      2070-0040,
                                                              2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.190.................................................      2070-0040,
                                                              2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.240.................................................      2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.290.................................................      2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.340.................................................      2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.390.................................................      2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.440.................................................      2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.490.................................................      2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.540.................................................      2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.590.................................................      2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.640.................................................      2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.690.................................................      2070-0057,
                                                              2070-0060,
                                                               2070-0107
158.740.................................................      2070-0057,
                                                              2070-0060,
                                                               2070-0107
------------------------------------------------------------------------
                   Good Laboratory Practice Standards
------------------------------------------------------------------------
Part 160................................................      2070-0024,
                                                              2070-0032,
                                                              2070-0040,
                                                              2070-0055,
                                                              2070-0057,
                                                              2070-0060,
                                                               2070-0107
------------------------------------------------------------------------
                State Registration of Pesticide Products
------------------------------------------------------------------------
162.153.................................................       2070-0055
------------------------------------------------------------------------
           Certification of Usefulness of Pesticide Chemicals
------------------------------------------------------------------------
163.4...................................................      2070-0060,
                                                               2070-0024
163.5...................................................      2070-0060,
                                                               2070-0024
------------------------------------------------------------------------
   Exemption of Federal and State Agencies for Use of Pesticides Under
                          Emergency Conditions
------------------------------------------------------------------------
166.20..................................................       2070-0032
166.32..................................................       2070-0032
166.43..................................................       2070-0032
166.50..................................................       2070-0032
------------------------------------------------------------------------
        Registration of Pesticide and Active Ingredient Producing
             Establishments, Submission of Pesticide Reports
------------------------------------------------------------------------
Part 167................................................       2070-0078
------------------------------------------------------------------------
         Statements of Enforcement Policies and Interpretations
------------------------------------------------------------------------
168.65..................................................       2070-0027
168.75..................................................       2070-0027
168.85..................................................      2070-0027,
                                                             2070-0028,,
                                                               2070-0078
------------------------------------------------------------------------
       Books and Records of Pesticide Production and Distribution
------------------------------------------------------------------------
169.2...................................................       2070-0028
------------------------------------------------------------------------
         Worker Protection Standards for Agricultural Pesticides
------------------------------------------------------------------------
Part 170................................................       2070-0148
------------------------------------------------------------------------
                 Certification of Pesticide Applicators
------------------------------------------------------------------------
171.7...................................................       2070-0029
171.8...................................................       2070-0029
171.9...................................................       2070-0029
171.10..................................................       2070-0029
171.11..................................................       2070-0029
------------------------------------------------------------------------
                        Experimental Use Permits
------------------------------------------------------------------------
172.4...................................................       2070-0040
172.8...................................................       2070-0040
------------------------------------------------------------------------
                  Issuance of Food Additive Regulations
------------------------------------------------------------------------
177.81..................................................       2070-0024
177.92..................................................       2070-0024
177.98..................................................       2070-0024
177.99..................................................       2070-0024
177.102.................................................       2070-0024
177.105.................................................       2070-0024
177.110.................................................       2070-0024
177.116.................................................       2070-0024
------------------------------------------------------------------------
 Tolerances and Exemptions from Tolerances for Pesticide Chemicals in or
                     on Raw Agricultural Commodities
------------------------------------------------------------------------
180.7...................................................       2070-0024
180.8...................................................       2070-0024
180.9...................................................       2070-0024
180.31..................................................       2070-0024
180.32..................................................       2070-0024
180.33..................................................       2070-0024
------------------------------------------------------------------------
                      404 State Program Regulations
------------------------------------------------------------------------
233.10-233.12...........................................       2040-0168
233.21..................................................       2040-0168
233.30..................................................       2040-0168
233.50..................................................       2040-0168
233.52..................................................       2040-0168
233.61..................................................       2040-0140
------------------------------------------------------------------------
   Criteria for Classification of Solid Waste Disposal Facilities and
                                Practices
------------------------------------------------------------------------
257.24..................................................       2050-0154
257.25..................................................       2050-0154
257.27..................................................       2050-0154
------------------------------------------------------------------------

[[Page 580]]

              Criteria for Municipal Solid Waste Landfills
------------------------------------------------------------------------
Part 258................................................       2050-0122
258.10-258.16...........................................       2050-0122
258.20..................................................       2050-0122
258.23..................................................       2050-0122
258.28-258.29...........................................       2050-0122
258.51..................................................       2050-0122
258.53-258.55...........................................       2050-0122
258.57-258.58...........................................       2050-0122
258.60-258.61...........................................       2050-0122
258.71-258.74...........................................       2050-0122
------------------------------------------------------------------------
               Hazardous Waste Management System: General
------------------------------------------------------------------------
260.20-260.22...........................................       2050-0053
260.23..................................................       2050-0145
260.31-260.33...........................................       2050-0053
------------------------------------------------------------------------
              Identification and Listing of Hazardous Waste
------------------------------------------------------------------------
261.3...................................................       2050-0085
261.4...................................................       2050-0053
261.35..................................................       2050-0115
------------------------------------------------------------------------
          Standards Applicable to Generators of Hazardous Waste
------------------------------------------------------------------------
262.12..................................................       2050-0028
262.20..................................................       2050-0039
262.22-262.23...........................................       2050-0039
262.34..................................................      2050-0035,
                                                               2050-0085
262.40(a)...............................................       2050-0039
262.40(b)...............................................       2050-0024
262.40(c)...............................................       2050-0035
262.41..................................................       2050-0024
262.42..................................................       2050-0039
262.43..................................................       2050-0035
262.44(a)-(b)...........................................       2050-0039
262.44(c)...............................................       2050-0035
262.53-262.57...........................................       2050-0035
262.60..................................................       2050-0035
------------------------------------------------------------------------
         Standards Applicable to Transporters of Hazardous Waste
------------------------------------------------------------------------
263.11..................................................       2050-0028
263.20-263.22...........................................       2050-0039
263.30..................................................       2050-0039
------------------------------------------------------------------------
    Standards for Owners and Operators of Hazardous Waste Treatment,
                    Storage, and Disposal Facilities
------------------------------------------------------------------------
264.11..................................................       2050-0028
264.12(a)...............................................       2050-0120
264.13..................................................      2050-0120,
                                                               2050-0009
264.14..................................................       2050-0009
264.15..................................................      2050-0120,
                                                               2050-0009
264.16..................................................      2050-0120,
                                                               2050-0009
264.17..................................................       2050-0120
264.18..................................................       2050-0009
264.19..................................................       2050-0009
264.32..................................................       2050-0009
264.35..................................................       2050-0009
264.37..................................................       2050-0120
264.51..................................................       2050-0009
264.52..................................................       2050-0009
264.53..................................................       2050-0120
264.54..................................................       2050-0120
264.56..................................................       2050-0120
264.71..................................................       2050-0039
264.72..................................................       2050-0039
264.73..................................................       2050-0120
264.74..................................................       2050-0120
264.75..................................................       2050-0024
264.76..................................................       2050-0039
264.90..................................................       2050-0009
264.96..................................................       2050-0120
264.97(g)...............................................       2050-0120
264.97(h)...............................................       2050-0009
264.97(j)...............................................       2050-0120
264.98(c), (g)(1), (g)(5), (g)(6).......................       2050-0033
264.98(g)(4), (h).......................................       2050-0009
264.99(c), (g), (h)(1), (i)(1), (i)(2)..................       2050-0033
264.99(h)(2), (i)(3), (j)...............................       2050-0009
264.100(e), (f), (g)....................................       2050-0033
264.100(h)..............................................       2050-0009
264.101.................................................       2050-0120
264.112(a), (b), (c)....................................       2050-0009
264.112(d)..............................................       2050-0120
264.113(a), (b), (d)....................................       2050-0120
264.113(e)..............................................       2050-0050
264.115.................................................       2050-0120
264.116.................................................       2050-0120
264.118.................................................       2050-0009
264.119(a), (b).........................................       2050-0120
264.119(c)..............................................       2050-0009
264.120.................................................       2050-0120
264.142(a)..............................................       2050-0009
264.142(b), (c), (d)....................................       2050-0120
264.143.................................................       2050-0120
264.144(a)..............................................       2050-0009
264.144(b), (c), (d)....................................       2050-0120
264.145.................................................       2050-0120
264.147(a)(7), (b)(7), (f),(g)..........................       2050-0120
264.147(a)(1), (b)(1), (c), (f), (g), (h), (i), (j).....       2050-0009
264.148.................................................       2050-0120
264.149.................................................       2050-0009
264.150.................................................       2050-0009
264.190.................................................       2050-0050
264.191.................................................       2050-0050
264.192(a)..............................................       2050-0009
264.192(g)..............................................       2050-0050
264.193(c), (d), (e), (g), (h)..........................       2050-0009
264.193(i)..............................................       2050-0050
264.196.................................................       2050-0050
264.197(b)..............................................       2050-0050
264.197(c)..............................................       2050-0009
264.221.................................................       2050-0009
264.222(a)..............................................       2050-0009
264.222(b)..............................................       2050-0050
264.223(a)..............................................       2050-0009
264.223(b), (c).........................................       2050-0050
264.226(c)..............................................      2050-0050,
                                                               2050-0009
264.226(d)..............................................       2050-0050
264.227.................................................       2050-0050
264.231.................................................       2050-0009
264.251.................................................       2050-0009
264.252(a)..............................................       2050-0009
264.252(b)..............................................       2050-0050
264.253(a)..............................................       2050-0009
264.253(b), (c).........................................       2050-0050
264.254.................................................       2050-0050
264.259.................................................       2050-0009
264.271.................................................       2050-0009
264.272.................................................       2050-0009
264.276.................................................      2050-0050,
                                                               2050-0009
264.278(a)-(f), (h).....................................       2050-0050
264.278(g)..............................................      2050-0050,
                                                               2050-0009
264.280.................................................       2050-0050
264.283.................................................       2050-0009

[[Page 581]]

264.301.................................................       2050-0009
264.302(a)..............................................       2050-0009
264.302(b)..............................................       2050-0050
264.303(a)..............................................       2050-0009
264.303(b)..............................................       2050-0050
264.304(a)..............................................       2050-0009
264.304(b), (c).........................................       2050-0050
264.314.................................................       2050-0050
264.317.................................................       2050-0009
264.340.................................................       2050-0009
264.343.................................................       2050-0050
264.344.................................................       2050-0009
264.347.................................................       2050-0050
264.552.................................................       2050-0009
264.570.................................................       2050-0050
264.571.................................................       2050-0050
264.573.................................................       2050-0050
264.574.................................................       2050-0050
264.575.................................................       2050-0009
264.603.................................................       2050-0050
264.1033(a).............................................       2050-0009
264.1033(j).............................................       2050-0050
264.1034................................................       2050-0050
264.1035................................................       2050-0050
264.1036................................................       2050-0050
264.1061................................................       2050-0050
264.1062................................................       2050-0050
264.1063................................................       2050-0050
264.1064................................................      2050-0050,
                                                               2050-0009
264.1065................................................       2050-0050
264.1089................................................       2060-0318
264.1090................................................       2060-0318
264.1100................................................       2050-0050
264.1101................................................       2050-0050
------------------------------------------------------------------------
  Interim Status Standards for Owners and Operators of Hazardous Waste
               Treatment, Storage, and Disposal Facilities
------------------------------------------------------------------------
265.11..................................................       2050-0028
265.12(a)...............................................       2050-0120
265.13..................................................       2050-0120
265.15..................................................       2050-0120
265.16..................................................       2050-0120
265.19..................................................       2050-0120
265.37..................................................       2050-0120
265.51..................................................       2050-0120
265.52..................................................       2050-0120
265.53..................................................       2050-0120
265.54..................................................       2050-0120
265.56..................................................       2050-0120
265.71..................................................       2050-0039
265.72..................................................       2050-0039
265.73..................................................       2050-0120
265.75..................................................       2050-0024
265.76..................................................       2050-0039
265.90..................................................       2050-0033
265.92..................................................       2050-0033
265.93..................................................       2050-0033
265.94..................................................       2050-0033
265.112.................................................       2050-0120
265.113(a), (b), (d)....................................       2050-0120
265.113(e)..............................................       2050-0050
265.115.................................................       2050-0120
265.116.................................................       2050-0120
265.118.................................................       2050-0120
265.119.................................................       2050-0120
265.120.................................................       2050-0120
265.142.................................................       2050-0120
265.143.................................................       2050-0120
265.144.................................................       2050-0120
265.145.................................................       2050-0120
265.147.................................................       2050-0120
265.148.................................................       2050-0120
265.149.................................................       2050-0120
265.150.................................................       2050-0120
265.190.................................................      2050-0035,
                                                               2050-0050
265.191.................................................      2050-0035,
                                                               2050-0050
265.192.................................................      2050-0035,
                                                               2050-0050
265.193.................................................      2050-0035,
                                                               2050-0050
265.195.................................................       2050-0120
265.196.................................................      2050-0035,
                                                               2050-0050
265.197(b)..............................................       2050-0050
265.197(c)..............................................       2050-0120
265.221.................................................       2050-0050
265.222.................................................       2050-0050
265.223.................................................       2050-0050
265.225.................................................       2050-0050
265.226.................................................       2050-0050
265.229.................................................       2050-0050
265.254.................................................       2050-0050
265.255.................................................       2050-0050
265.259.................................................       2050-0050
265.260.................................................       2050-0050
265.273.................................................       2050-0120
265.276.................................................       2050-0050
265.278.................................................       2050-0050
265.280.................................................       2050-0050
265.301.................................................       2050-0050
265.302.................................................       2050-0050
265.303.................................................       2050-0050
265.304.................................................       2050-0050
265.314.................................................       2050-0050
265.340.................................................       2050-0050
265.352.................................................       2050-0050
265.383.................................................       2050-0050
265.404.................................................       2050-0050
265.440.................................................       2050-0050
265.441.................................................       2050-0050
265.443.................................................       2050-0050
265.444.................................................       2050-0050
265.445.................................................       2050-0120
265.1033................................................       2050-0050
265.1034................................................       2050-0050
265.1035................................................       2050-0050
265.1061................................................       2050-0050
265.1062................................................       2050-0050
265.1063................................................       2050-0050
265.1064................................................       2050-0050
265.1090................................................       2060-0318
265.1100................................................       2050-0050
265.1101................................................       2050-0050
------------------------------------------------------------------------
 Standards for the Management of Specific Hazardous Wastes and Specific
             Types of Hazardous Waste Management Facilities
------------------------------------------------------------------------
266.70 (b)..............................................       2050-0028
266.70(c)...............................................       2050-0050
266.80..................................................       2050-0028
266.100.................................................       2050-0073
266.102.................................................       2050-0073
266.103.................................................       2050-0073
266.104.................................................       2050-0073
266.106.................................................       2050-0073
266.107.................................................       2050-0073
266.108.................................................       2050-0073
266.109.................................................       2050-0073
266.111.................................................       2050-0073
266.112.................................................       2050-0073

[[Page 582]]

Appendix IX.............................................       2050-0073
------------------------------------------------------------------------
                       Land Disposal Restrictions
------------------------------------------------------------------------
268.4-268.5.............................................       2050-0085
268.6...................................................       2050-0062
268.7...................................................       2050-0085
268.9...................................................       2050-0085
268.42..................................................       2050-0085
268.44..................................................       2050-0085
------------------------------------------------------------------------
  EPA Administered Permit Programs: The Hazardous Waste Permit Program
------------------------------------------------------------------------
270.1...................................................      2050-0028,
                                                              2050-0034,
                                                               2050-0009
270.10..................................................       2050-0009
270.11..................................................       2050-0034
270.13..................................................       2050-0034
270.14..................................................       2050-0009
270.14(b)(21)...........................................      2050-0062,
                                                               2050-0085
270.15..................................................       2050-0009
270.16..................................................       2050-0009
270.17..................................................       2050-0009
270.18..................................................       2050-0009
270.19..................................................       2050-0009
270.20..................................................       2050-0009
270.21..................................................       2050-0009
270.22..................................................       2050-0073
270.23..................................................       2050-0009
270.24..................................................       2050-0009
270.25..................................................       2050-0009
270.26..................................................       2050-0115
270.30..................................................       2050-0120
270.33..................................................       2050-0009
270.40..................................................       2050-0009
270.41..................................................       2050-0009
270.42..................................................       2050-0009
270.51..................................................       2050-0009
270.62..................................................      2050-0009,
                                                               2050-0149
270.63..................................................       2050-0009
270.65..................................................       2050-0009
270.66..................................................      2050-0073,
                                                               2050-0149
270.72..................................................       2050-0034
270.73..................................................       2050-0009
------------------------------------------------------------------------
    Requirements for Authorization of State Hazardous Waste Programs
------------------------------------------------------------------------
271.5-271.8.............................................       2050-0041
271.20-271.21...........................................       2050-0041
271.23..................................................       2050-0041
------------------------------------------------------------------------
                Standards for Universal Waste Management
------------------------------------------------------------------------
273.14..................................................       2050-0145
273.15..................................................       2050-0145
273.18..................................................       2050-0145
273.32..................................................       2050-0145
273.34..................................................       2050-0145
273.35..................................................       2050-0145
273.38..................................................       2050-0145
273.39..................................................       2050-0145
273.61..................................................       2050-0145
273.62..................................................       2050-0145
273.80..................................................       2050-0145
------------------------------------------------------------------------
                  Standards for Management of Used Oil
------------------------------------------------------------------------
279.10-279.11...........................................       2050-0124
279.42..................................................      2050-0028,
                                                               2050-0124
279.43-279.44...........................................       2050-0124
279.46..................................................       2050-0050
279.51..................................................       2050-0028
279.52-279.55...........................................       2050-0124
279.56..................................................       2050-0050
279.57..................................................      2050-0050,
                                                               2050-0124
279.62..................................................       2050-0028
279.63..................................................       2050-0124
279.65-279.66...........................................       2050-0050
279.72..................................................       2050-0050
279.73..................................................       2050-0028
279.74-279.75...........................................       2050-0050
279.82..................................................       2050-0124
------------------------------------------------------------------------
  Technical Standards and Corrective Action Requirements for Owners and
              Operators of Underground Storage Tanks (USTs)
------------------------------------------------------------------------
280.11(a)...............................................       2050-0068
280.20(a)-(b)...........................................       2050-0068
280.20(e)...............................................       2050-0068
280.22(a)-(f)...........................................       2050-0068
280.22(g)...............................................       2050-0068
280.31..................................................       2050-0068
280.33(f)...............................................       2050-0068
280.34(a)...............................................       2050-0068
280.34(b)...............................................       2050-0068
280.34(c)...............................................       2050-0068
280.40..................................................       2050-0068
280.43..................................................       2050-0068
280.44..................................................       2050-0068
280.45..................................................       2050-0068
280.50..................................................       2050-0068
280.53..................................................       2050-0068
280.61..................................................       2050-0068
280.62..................................................       2050-0068
280.63..................................................       2050-0068
280.64..................................................       2050-0068
280.65..................................................       2050-0068
280.66(a)...............................................       2050-0068
280.66(c)...............................................       2050-0068
280.66(d)...............................................       2050-0068
280.67..................................................       2050-0068
280.71(a)...............................................       2050-0068
280.72(a)...............................................       2050-0068
280.74..................................................       2050-0068
280.95..................................................       2050-0068
280.96..................................................       2050-0068
280.97..................................................       2050-0068
280.98..................................................       2050-0068
280.99..................................................       2050-0068
280.100.................................................       2050-0068
280.101.................................................       2050-0068
280.102.................................................       2050-0068
280.103.................................................       2050-0068
280.104.................................................       2050-0068
280.105.................................................       2050-0068
280.106.................................................       2050-0068
280.107.................................................       2050-0068
280.108.................................................       2050-0068
280.109(a)..............................................       2050-0068
280.109(b)..............................................       2050-0068
280.110.................................................       2050-0068
280.111.................................................       2050-0068
280.111(b)(11)..........................................       2050-0068
280.114(a)-(d)..........................................       2050-0068
280.114(e)..............................................       2050-0068
------------------------------------------------------------------------
           Approval of State Underground Storage Tank Programs
------------------------------------------------------------------------
281.120(a)..............................................       2050-0068

[[Page 583]]

281.120(g)..............................................       2050-0068
281.121.................................................       2050-0068
281.122.................................................       2050-0068
281.124.................................................       2050-0068
281.125.................................................       2050-0068
281.140.................................................       2050-0068
281.143(a)..............................................       2050-0068
281.150.................................................       2050-0068
281.152.................................................       2050-0068
281.161.................................................       2050-0068
------------------------------------------------------------------------
    National Oil and Hazardous Substances Pollution Contingency Plan
------------------------------------------------------------------------
300.405.................................................       2050-0046
300.425.................................................       2050-0095
300.430.................................................       2050-0096
300.435.................................................       2050-0096
300.920.................................................       2050-0141
Part 300, appendix A....................................       2050-0095
------------------------------------------------------------------------
          Designation, reportable quantities, and notification
------------------------------------------------------------------------
302.4...................................................       2050-0046
302.6...................................................       2050-0046
302.8...................................................       2050-0086
------------------------------------------------------------------------
       Hazardous Substances Superfund; Response Claims Procedures
------------------------------------------------------------------------
307.11-307.14...........................................       2050-0106
307.21-307.23...........................................       2050-0106
307.30-307.32...........................................       2050-0106
------------------------------------------------------------------------
 Reimbursement to Local Governments for Emergency Response to Hazardous
                           Substance Releases
------------------------------------------------------------------------
310.05..................................................       2050-0077
310.10-310.12...........................................       2050-0077
310.20..................................................       2050-0077
310.30..................................................       2050-0077
310.40..................................................       2050-0077
310.50..................................................       2050-0077
310.60..................................................       2050-0077
310.70..................................................       2050-0077
310.80..................................................       2050-0077
310.90..................................................       2050-0077
Part 310, appendix II...................................       2050-0077
------------------------------------------------------------------------
Worker Protection Standards for Hazardous Waste Operations and Emergency
                                Response
------------------------------------------------------------------------
311.1-311.2.............................................       2050-0105
------------------------------------------------------------------------
Trade Secrecy Claims for Emergency Planning and Community Right-to-Know;
                          Health Professionals
------------------------------------------------------------------------
350.5-350.16............................................       2050-0078
350.27..................................................       2050-0078
350.40..................................................       2050-0078
------------------------------------------------------------------------
                   Emergency planning and notification
------------------------------------------------------------------------
Part 355, appendix A, appendix B........................       2050-0046
------------------------------------------------------------------------
        Toxic Chemical Release Reporting: Community Right-to-Know
------------------------------------------------------------------------
Part 372................................................       2070-0093
Part 372, subpart A.....................................      2070-0093,
                                                               2070-0143
372.22..................................................      2070-0093,
                                                               2070-0143
372.25..................................................       2070-0093
372.27..................................................       2070-0143
372.30..................................................      2070-0093,
                                                               2070-0143
372.38..................................................      2070-0093,
                                                               2070-0143
Part 372, subpart C.....................................      2070-0093,
                                                               2070-0143
Part 372, subpart D.....................................      2070-0093,
                                                               2070-0143
372.85..................................................       2070-0093
372.95..................................................       2070-0143
------------------------------------------------------------------------
    General Pretreatment Regulations for Existing and New Sources of
                                Pollution
------------------------------------------------------------------------
403.5(b)................................................       2040-0009
403.6-403.7.............................................       2040-0009
403.8(a)-(e)............................................       2040-0009
403.8(f)................................................       2040-0009
403.9-403.10............................................       2040-0009
403.12(b)-(g)...........................................       2040-0009
403.12(h), (i)..........................................       2040-0009
403.12(j), (k), (l), (o)................................       2040-0009
403.12(m), (p)..........................................       2040-0009
403.13..................................................       2040-0009
403.15..................................................       2040-0009
403.17-403.18...........................................      2040-0009,
                                                               2040-0170
------------------------------------------------------------------------
             Steam Electric Generating Point Source Category
------------------------------------------------------------------------
423.12-423.13...........................................       2040-0033
423.15..................................................       2040-0033
------------------------------------------------------------------------
            Pulp, Paper, and Paperboard Point Source Category
------------------------------------------------------------------------
430.14-430.17...........................................       2040-0033
430.24-430.27...........................................       2040-0033
430.54-430.57...........................................       2040-0033
430.64-430.67...........................................       2040-0033
430.74-430.77...........................................       2040-0033
430.84-430.87...........................................       2040-0033
430.94-430.97...........................................       2040-0033
430.104-430.107.........................................       2040-0033
430.114-430.117.........................................       2040-0033
430.134-430.137.........................................       2040-0033
430.144-430.147.........................................       2040-0033
430.154-430.157.........................................       2040-0033
430.164-430.167.........................................       2040-0033
430.174-430.177.........................................       2040-0033
430.184-430.187.........................................       2040-0033
430.194-430.197.........................................       2040-0033
430.204-430.207.........................................       2040-0033
430.214-430.217.........................................       2040-0033
430.224-430.227.........................................       2040-0033
430.234-430.237.........................................       2040-0033
430.244-430.247.........................................       2040-0033
430.254-430.257.........................................       2040-0033
430.264-430.267.........................................       2040-0033
------------------------------------------------------------------------
        The Builders' Paper and Board Mills Point Source Category
------------------------------------------------------------------------
431.14-431.17...........................................       2040-0033
------------------------------------------------------------------------
           Pharmaceutical Manufacturing Point Source Category
------------------------------------------------------------------------
439.14-439.17...........................................       2040-0033
439.24-439.27...........................................       2040-0033
439.34-439.37...........................................       2040-0033
439.44-439.47...........................................       2040-0033
------------------------------------------------------------------------

[[Page 584]]

                   Coil Coating Point Source Category
------------------------------------------------------------------------
465.03..................................................       2040-0033
------------------------------------------------------------------------
                Porcelain Enameling Point Source Category
------------------------------------------------------------------------
466.03..................................................       2040-0033
------------------------------------------------------------------------
                 Aluminum Forming Point Source Category
------------------------------------------------------------------------
467.03..................................................       2040-0033
------------------------------------------------------------------------
              State Sludge Management Program Requirements
------------------------------------------------------------------------
501.15(a)...............................................      2040-0086,
                                                               2040-0110
501.15(b)...............................................      2040-0004,
                                                              2040-0068,
                                                               2040-0110
501.15(c)...............................................       2040-0068
501.16..................................................       2040-0057
501.21..................................................       2040-0057
------------------------------------------------------------------------
           Standards for the Use or Disposal of Sewage Sludge
------------------------------------------------------------------------
503.17-503.18...........................................       2040-0157
503.27-503.28...........................................       2040-0157
503.47-503.48...........................................       2040-0157
------------------------------------------------------------------------
                     Fuel Economy of Motor Vehicles
------------------------------------------------------------------------
600.006-86..............................................       2060-0104
600.007-80..............................................       2060-0104
600.010-86..............................................       2060-0104
600.113-88..............................................       2060-0104
600.113-93..............................................       2060-0104
600.206-86..............................................       2060-0104
600.207-86..............................................       2060-0104
600.209-85..............................................       2060-0104
600.306-86..............................................       2060-0104
600.307-86..............................................       2060-0104
600.311-86..............................................       2060-0104
600.312-86..............................................       2060-0104
600.313-86..............................................       2060-0104
600.314-86..............................................       2060-0104
600.507-86..............................................       2060-0104
600.509-86..............................................       2060-0104
600.510-86..............................................       2060-0104
600.512-86..............................................       2060-0104
------------------------------------------------------------------------
                  Toxic Substances Control Act: General
------------------------------------------------------------------------
700.45..................................................      2070-0012,
                                                               2070-0038
------------------------------------------------------------------------
                Reporting and Recordkeeping Requirements
------------------------------------------------------------------------
704.5...................................................      2010-0019,
                                                               2070-0067
704.11..................................................      2010-0019,
                                                               2070-0067
704.25..................................................       2070-0067
704.33..................................................       2070-0067
704.43..................................................       2070-0067
704.45..................................................       2070-0067
704.95..................................................       2070-0067
704.102.................................................       2070-0067
704.104.................................................  2070-0067L='s
                                                            '
704.175.................................................       2070-0067
                      Chemical Imports and Exports
------------------------------------------------------------------------
707.65..................................................       2070-0030
707.67..................................................       2070-0030
707.72..................................................       2070-0030
------------------------------------------------------------------------
                     Inventory Reporting Regulations
------------------------------------------------------------------------
Part 710................................................       2070-0070
------------------------------------------------------------------------
                       Chemical Information Rules
------------------------------------------------------------------------
712.5...................................................       2070-0054
712.7...................................................       2070-0054
712.20..................................................       2070-0054
712.28..................................................       2070-0054
712.30..................................................       2070-0054
------------------------------------------------------------------------
                    Health and Safety Data Reporting
------------------------------------------------------------------------
716.5...................................................       2070-0004
716.10..................................................       2070-0004
716.20..................................................       2070-0004
716.25..................................................       2070-0004
716.30..................................................       2070-0004
716.35..................................................       2070-0004
716.40..................................................       2070-0004
716.45..................................................       2070-0004
716.50..................................................       2070-0004
716.60..................................................       2070-0004
716.65..................................................       2070-0004
716.105.................................................       2070-0004
716.120.................................................       2070-0004
------------------------------------------------------------------------
    Records and Reports of Allegations That Chemical Substances Cause
       Significant Adverse Reactions to Health or the Environment
------------------------------------------------------------------------
717.5...................................................       2070-0017
717.7...................................................       2070-0017
717.12..................................................       2070-0017
717.15..................................................       2070-0017
717.17..................................................       2070-0017
------------------------------------------------------------------------
                       Premanufacture Notification
------------------------------------------------------------------------
720.1...................................................       2070-0012
720.22..................................................       2070-0012
720.25..................................................       2070-0012
720.30..................................................       2070-0012
720.36..................................................       2070-0012
720.38..................................................       2070-0012
Part 720, subpart C.....................................       2070-0012
720.62..................................................       2070-0012
720.75..................................................       2070-0012
720.78..................................................       2070-0012
720.80..................................................       2070-0012
720.85..................................................       2070-0012
720.87..................................................       2070-0012
720.90..................................................       2070-0012
720.102.................................................       2070-0012
Part 720, appendix A....................................       2070-0012
------------------------------------------------------------------------
               Significant New Uses of Chemical Substances
------------------------------------------------------------------------
Part 721, subpart A.....................................      2070-0012,
                                                               2070-0038
721.72..................................................      2070-0012,
                                                               2070-0038
721.125.................................................      2070-0012,
                                                               2070-0038
721.160.................................................      2070-0012,
                                                               2070-0038
721.170.................................................      2070-0012,
                                                               2070-0038
721.185.................................................      2070-0012,
                                                               2070-0038
721.225.................................................       2070-0012

[[Page 585]]

721.267.................................................       2070-0012
721.275.................................................       2070-0012
721.285.................................................       2070-0012
721.320.................................................       2070-0012
721.323.................................................       2070-0012
721.325.................................................       2070-0012
721.336.................................................       2070-0012
721.370.................................................       2070-0012
721.390.................................................       2070-0012
721.400.................................................       2070-0012
721.415.................................................       2070-0012
721.430.................................................       2070-0012
721.445.................................................       2070-0012
721.460.................................................       2070-0012
721.470.................................................       2070-0012
721.484.................................................       2070-0012
721.490.................................................       2070-0012
721.505.................................................       2070-0012
721.520.................................................       2070-0012
721.530.................................................       2070-0012
721.536.................................................       2070-0012
721.540.................................................       2070-0012
721.550.................................................       2070-0012
721.562.................................................       2070-0012
721.575.................................................       2070-0012
721.600.................................................       2070-0012
721.625.................................................       2070-0012
721.639.................................................       2070-0012
721.642.................................................       2070-0012
721.646.................................................       2070-0012
721.650.................................................       2070-0038
721.700.................................................       2070-0012
721.715.................................................       2070-0012
721.750.................................................       2070-0012
721.757.................................................       2070-0012
721.775.................................................       2070-0012
721.785.................................................       2070-0012
721.805.................................................       2070-0012
721.825.................................................       2070-0012
721.840.................................................       2070-0012
721.875.................................................       2070-0012
721.925.................................................       2070-0012
721.950.................................................       2070-0012
721.982.................................................       2070-0012
721.1000................................................       2070-0012
721.1025................................................       2070-0038
721.1050................................................       2070-0012
721.1068................................................       2070-0012
721.1075................................................       2070-0012
721.1120................................................       2070-0012
721.1150................................................       2070-0012
721.1175................................................       2070-0012
721.1187................................................       2070-0012
721.1193................................................       2070-0012
721.1210................................................       2070-0012
721.1225................................................       2070-0012
721.1240................................................       2070-0012
721.1300................................................       2070-0012
721.1325................................................       2070-0012
721.1350................................................       2070-0012
721.1372................................................       2070-0012
721.1375................................................       2070-0012
721.1425................................................       2070-0038
721.1430................................................       2070-0038
721.1435................................................       2070-0038
721.1440................................................       2070-0038
721.1450................................................       2070-0012
721.1500................................................       2070-0012
721.1525................................................       2070-0012
721.1550................................................       2070-0012
721.1555................................................       2070-0012
721.1568................................................       2070-0012
721.1575................................................       2070-0012
721.1612................................................       2070-0012
721.1625................................................       2070-0012
721.1630................................................       2070-0012
721.1637................................................       2070-0012
721.1640................................................       2070-0012
721.1643................................................       2070-0012
721.1645................................................       2070-0012
721.1650................................................       2070-0012
721.1660................................................       2070-0038
721.1675................................................       2070-0012
721.1700................................................       2070-0012
721.1725................................................       2070-0012
721.1728................................................       2070-0012
721.1732................................................       2070-0012
721.1735................................................       2070-0012
721.1737................................................       2070-0012
721.1738................................................       2070-0012
721.1740................................................       2070-0012
721.1745................................................       2070-0012
721.1750................................................       2070-0012
721.1755................................................       2070-0012
721.1765................................................       2070-0012
721.1769................................................       2070-0012
721.1775................................................       2070-0012
721.1790................................................       2070-0038
721.1800................................................       2070-0012
721.1820................................................       2070-0012
721.1825................................................       2070-0012
721.1850................................................       2070-0012
721.1875................................................       2070-0012
721.1900................................................       2070-0012
721.1920................................................       2070-0012
721.1925................................................       2070-0012
721.1950................................................       2070-0012
721.2025................................................       2070-0012
721.2050................................................       2070-0012
721.2075................................................       2070-0012
721.2084................................................       2070-0038
721.2085................................................       2070-0012
721.2086................................................       2070-0012
721.2088................................................       2070-0012
721.2089................................................       2070-0012
721.2092................................................       2070-0038
721.2095................................................       2070-0012
721.2097................................................       2070-0012
721.2120................................................       2070-0012
721.2140................................................       2070-0012
721.2170................................................       2070-0012
721.2175................................................       2070-0012
721.2250................................................       2070-0012
721.2260................................................       2070-0012
721.2270................................................       2070-0012
721.2275................................................       2070-0012
721.2287................................................       2070-0038
721.2340................................................       2070-0012
721.2355................................................       2070-0038
721.2380................................................       2070-0012
721.2410................................................       2070-0012
721.2420................................................       2070-0012
721.2475................................................       2070-0012
721.2520................................................       2070-0012
721.2527................................................       2070-0012
721.2540................................................       2070-0012
721.2560................................................       2070-0012
721.2565................................................       2070-0012
721.2575................................................       2070-0012
721.2600................................................       2070-0038
721.2625................................................       2070-0012
721.2650................................................       2070-0012
721.2675................................................       2070-0012
721.2725................................................       2070-0038
721.2750................................................       2070-0012
721.2800................................................       2070-0038

[[Page 586]]

721.2815................................................       2070-0012
721.2825................................................       2070-0012
721.2840................................................       2070-0012
721.2860................................................       2070-0012
721.2880................................................       2070-0012
721.2900................................................       2070-0012
721.2920................................................       2070-0012
721.2930................................................       2070-0012
721.2940................................................       2070-0012
721.2950................................................       2070-0012
721.3000................................................       2070-0012
721.3020................................................       2070-0012
721.3028................................................       2070-0012
721.3034................................................       2070-0012
721.3040................................................       2070-0012
721.3060................................................       2070-0012
721.3063................................................       2070-0012
721.3080................................................       2070-0012
721.3100................................................       2070-0012
721.3120................................................       2070-0012
721.3140................................................       2070-0012
721.3152................................................       2070-0012
721.3160................................................       2070-0038
721.3180................................................       2070-0012
721.3200................................................       2070-0012
721.3220................................................       2070-0038
721.3248................................................       2070-0012
721.3260................................................       2070-0012
721.3320................................................       2070-0012
721.3340................................................       2070-0012
721.3350................................................       2070-0038
721.3360................................................       2070-0012
721.3364................................................       2070-0012
721.3374................................................       2070-0012
721.3380................................................       2070-0012
721.3390................................................       2070-0012
721.3420................................................       2070-0012
721.3430................................................       2070-0038
721.3435................................................       2070-0012
721.3437................................................       2070-0012
721.3440................................................       2070-0012
721.3460................................................       2070-0012
721.3480................................................       2070-0012
721.3486................................................       2070-0012
721.3500................................................       2070-0012
721.3520................................................       2070-0012
721.3560................................................       2070-0012
721.3620................................................       2070-0012
721.3625................................................       2070-0012
721.3627................................................       2070-0012
721.3628................................................       2070-0012
721.3629................................................       2070-0012
721.3640................................................       2070-0012
721.3680................................................       2070-0012
721.3700................................................       2070-0012
721.3720................................................       2070-0012
721.3740................................................       2070-0012
721.3760................................................       2070-0012
721.3764................................................       2070-0012
721.3780................................................       2070-0012
721.3790................................................       2070-0012
721.3800................................................       2070-0012
721.3815................................................       2070-0012
721.3840................................................       2070-0012
721.3860................................................       2070-0012
721.3870................................................       2070-0012
721.3880................................................       2070-0012
721.3900................................................       2070-0012
721.4000................................................       2070-0012
721.4020................................................       2070-0012
721.4040................................................       2070-0012
721.4060................................................       2070-0012
721.4080................................................       2070-0038
721.4100................................................       2070-0012
721.4110................................................       2070-0012
721.4128................................................       2070-0012
721.4133................................................       2070-0012
721.4140................................................       2070-0038
721.4155................................................       2070-0038
721.4160................................................       2070-0038
721.4180................................................       2070-0038
721.4200................................................       2070-0012
721.4215................................................       2070-0012
721.4220................................................       2070-0012
721.4240................................................       2070-0012
721.4250................................................       2070-0012
721.4255................................................       2070-0012
721.4260................................................       2070-0012
721.4270................................................       2070-0012
721.4280................................................       2070-0012
721.4300................................................       2070-0012
721.4320................................................       2070-0012
721.4340................................................       2070-0012
721.4360................................................       2070-0038
721.4380................................................       2070-0012
721.4390................................................       2070-0012
721.4400................................................       2070-0012
721.4420................................................       2070-0012
721.4460................................................       2070-0012
721.4463................................................       2070-0012
721.4466................................................       2070-0012
721.4470................................................       2070-0012
721.4473................................................       2070-0012
721.4484................................................       2070-0012
721.4480................................................       2070-0012
721.4490................................................       2070-0012
721.4494................................................       2070-0012
721.4497................................................       2070-0012
721.4500................................................       2070-0012
721.4520................................................       2070-0012
721.4550................................................       2070-0012
721.4568................................................       2070-0012
721.4585................................................       2070-0012
721.4587................................................       2070-0012
721.4590................................................       2070-0012
721.4594................................................       2070-0012
721.4600................................................       2070-0012
721.4620................................................       2070-0012
721.4640................................................       2070-0012
721.4660................................................       2070-0012
721.4663................................................       2070-0012
721.4668................................................       2070-0012
721.4680................................................       2070-0012
721.4685................................................       2070-0012
721.4700................................................       2070-0012
721.4720................................................       2070-0012
721.4740................................................       2070-0038
721.4780................................................       2070-0012
721.4790................................................       2070-0012
721.4794................................................       2070-0012
721.4800................................................       2070-0012
721.4820................................................       2070-0012
721.4840................................................       2070-0012
721.4880................................................       2070-0012
721.4925................................................       2070-0038
721.5050................................................       2070-0012
721.5075................................................       2070-0012
721.5175................................................       2070-0038
721.5192................................................       2070-0012
721.5200................................................       2070-0012
721.5225................................................       2070-0012
721.5250................................................       2070-0012
721.5275................................................       2070-0012
721.5276................................................       2070-0012
721.5278................................................       2070-0012
721.5282................................................       2070-0012

[[Page 587]]

721.5285................................................       2070-0012
721.5300................................................       2070-0012
721.5310................................................       2070-0012
721.5325................................................       2070-0012
721.5330................................................       2070-0012
721.5350................................................       2070-0012
721.5375................................................       2070-0012
721.5385................................................       2070-0012
721.5400................................................       2070-0012
721.5425................................................       2070-0012
721.5450................................................       2070-0012
721.5475................................................       2070-0012
721.5500................................................       2070-0012
721.5525................................................       2070-0012
721.5540................................................       2070-0012
721.5545................................................       2070-0012
721.5550................................................       2070-0012
721.5575................................................       2070-0012
721.5600................................................       2070-0038
721.5700................................................       2070-0012
721.5705................................................       2070-0012
721.5710................................................       2070-0038
721.5740................................................       2070-0012
721.5760................................................       2070-0012
721.5763................................................       2070-0012
721.5769................................................       2070-0012
721.5780................................................       2070-0012
721.5800................................................       2070-0012
721.5820................................................       2070-0012
721.5840................................................       2070-0012
721.5860................................................       2070-0012
721.5880................................................       2070-0012
721.5900................................................       2070-0012
721.5910................................................       2070-0012
721.5915................................................       2070-0012
721.5920................................................       2070-0012
721.5930................................................       2070-0012
721.5960................................................       2070-0012
721.5970................................................       2070-0012
721.5980................................................       2070-0012
721.5990................................................       2070-0012
721.6000................................................       2070-0038
721.6020................................................       2070-0012
721.6060................................................       2070-0012
721.6070................................................       2070-0012
721.6080................................................       2070-0012
721.6085................................................       2070-0012
721.6090................................................       2070-0012
721.6097................................................       2070-0012
721.6100................................................       2070-0012
721.6110................................................       2070-0012
721.6120................................................       2070-0012
721.6140................................................       2070-0012
721.6160................................................       2070-0012
721.6180................................................       2070-0012
721.6186................................................       2070-0012
721.6200................................................       2070-0012
721.6220................................................       2070-0012
721.6440................................................       2070-0012
721.6470................................................       2070-0012
721.6500................................................       2070-0012
721.6520................................................       2070-0012
721.6540................................................       2070-0012
721.6560................................................       2070-0012
721.6580................................................       2070-0012
721.6600................................................       2070-0012
721.6620................................................       2070-0012
721.6625................................................       2070-0012
721.6640................................................       2070-0012
721.6660................................................       2070-0012
721.6680................................................       2070-0012
721.6700................................................       2070-0012
721.6720................................................       2070-0012
721.6740................................................       2070-0012
721.6760................................................       2070-0012
721.6780................................................       2070-0012
721.6820................................................       2070-0012
721.6840................................................       2070-0012
721.6880................................................       2070-0012
721.6900................................................       2070-0012
721.6920................................................       2070-0012
721.6940................................................       2070-0012
721.6960................................................       2070-0012
721.6980................................................       2070-0012
721.7000................................................       2070-0012
721.7020................................................       2070-0012
721.7040................................................       2070-0012
721.7046................................................       2070-0012
721.7080................................................       2070-0012
721.7100................................................       2070-0012
721.7140................................................       2070-0012
721.7160................................................       2070-0012
721.7180................................................       2070-0012
721.7200................................................       2070-0012
721.7210................................................       2070-0012
721.7220................................................       2070-0012
721.7240................................................       2070-0012
721.7260................................................       2070-0012
721.7280................................................       2070-0012
721.7300................................................       2070-0012
721.7320................................................       2070-0012
721.7340................................................       2070-0012
721.7360................................................       2070-0012
721.7370................................................       2070-0012
721.7400................................................       2070-0012
721.7420................................................       2070-0012
721.7440................................................       2070-0012
721.7450................................................       2070-0012
721.7460................................................       2070-0012
721.7480................................................       2070-0012
721.7500................................................       2070-0012
721.7540................................................       2070-0012
721.7560................................................       2070-0012
721.7580................................................       2070-0012
721.7600................................................       2070-0012
721.7620................................................       2070-0012
721.7655................................................       2070-0012
721.7660................................................       2070-0012
721.7680................................................       2070-0012
721.7780................................................       2070-0012
721.7710................................................       2070-0012
721.7720................................................       2070-0012
721.7700................................................       2070-0012
721.7740................................................       2070-0012
721.7760................................................       2070-0012
721.7770................................................       2070-0012
721.8075................................................       2070-0012
721.8082................................................       2070-0012
721.8090................................................       2070-0012
721.8100................................................       2070-0012
721.8155................................................       2070-0012
721.8160................................................       2070-0012
721.8170................................................       2070-0012
721.8175................................................       2070-0012
721.8225................................................       2070-0012
721.8250................................................       2070-0012
721.8265................................................       2070-0012
721.8275................................................       2070-0012
721.8290................................................       2070-0012
721.8300................................................       2070-0012
721.8325................................................       2070-0012
721.8335................................................       2070-0012
721.8350................................................       2070-0012
721.8375................................................       2070-0012
721.8400................................................       2070-0012
721.8425................................................       2070-0012

[[Page 588]]

721.8450................................................       2070-0012
721.8475................................................       2070-0012
721.8500................................................       2070-0012
721.8525................................................       2070-0012
721.8550................................................       2070-0012
721.8575................................................       2070-0012
721.8600................................................       2070-0012
721.8650................................................       2070-0012
721.8654................................................       2070-0012
721.8670................................................       2070-0012
721.8673................................................       2070-0012
721.8675................................................       2070-0012
721.8700................................................       2070-0012
721.8750................................................       2070-0012
721.8775................................................       2070-0012
721.8825................................................       2070-0012
721.8850................................................       2070-0012
721.8875................................................       2070-0012
721.8900................................................       2070-0012
721.8965................................................       2070-0012
721.9000................................................       2070-0038
721.9075................................................       2070-0012
721.9100................................................       2070-0012
721.9220................................................       2070-0012
721.9240................................................       2070-0012
721.9260................................................       2070-0012
721.9280................................................       2070-0012
721.9300................................................       2070-0012
721.9320................................................       2070-0012
721.9360................................................       2070-0012
721.9400................................................       2070-0012
721.9420................................................       2070-0012
721.9460................................................       2070-0012
721.9470................................................       2070-0038
721.9480................................................       2070-0012
721.9495................................................       2070-0012
721.9500................................................       2070-0012
721.9505................................................       2070-0012
721.9507................................................       2070-0012
721.9510................................................       2070-0012
721.9520................................................       2070-0012
721.9525................................................       2070-0012
721.9526................................................       2070-0012
721.9527................................................       2070-0012
721.9530................................................       2070-0012
721.9540................................................       2070-0012
721.9550................................................       2070-0012
721.9570................................................       2070-0012
721.9580................................................       2070-0038
721.9620................................................       2070-0012
721.9630................................................       2070-0012
721.9650................................................       2070-0012
721.9656................................................       2070-0012
721.9658................................................       2070-0012
721.9660................................................       2070-0038
721.9665................................................       2070-0012
721.9675................................................       2070-0012
721.9680................................................       2070-0012
721.9700................................................       2070-0012
721.9720................................................       2070-0012
721.9730................................................       2070-0012
721.9740................................................       2070-0012
721.9750................................................       2070-0012
721.9780................................................       2070-0012
721.9800................................................       2070-0012
721.9820................................................       2070-0012
721.9850................................................       2070-0012
721.9870................................................       2070-0012
721.9892................................................       2070-0012
721.9900................................................       2070-0012
721.9920................................................       2070-0012
721.9925................................................       2070-0012
721.9930................................................       2070-0038
721.9940................................................       2070-0012
721.9957................................................       2070-0038
721.9970................................................       2070-0012
721.9975................................................       2070-0012
------------------------------------------------------------------------
                 Premanufacture Notification Exemptions
------------------------------------------------------------------------
723.50..................................................       2070-0012
723.175.................................................       2070-0012
723.250(m)(1)...........................................       2070-0012
------------------------------------------------------------------------
Lead-Based Paint Poisioning Prevention in Certain Residential Structures
------------------------------------------------------------------------
Part 745, subpart F.....................................       2070-0151
Part 745, subpart L.....................................       2070-0155
Part 745, subpart Q.....................................       2070-0155
------------------------------------------------------------------------
                        Water Treatment Chemicals
------------------------------------------------------------------------
Part 749, subpart D.....................................       2060-0193
749.68..................................................       2060-0193
------------------------------------------------------------------------
Polychlorinated Biphenyls (PCBs) Manufacturing, Processing, Distribution
                    in Commerce, and Use Prohibitions
------------------------------------------------------------------------
761.20..................................................      2070-0008,
                                                               2070-0021
761.30..................................................      2070-0003,
                                                              2070-0008,
                                                               2070-0021
761.60..................................................       2070-0011
761.65..................................................       2070-0112
761.70..................................................       2070-0011
761.75..................................................       2070-0011
761.80..................................................       2070-0021
761.93..................................................       2070-0149
761.93(a)(1)(iii).......................................       2070-0149
761.93(b)...............................................       2070-0149
761.125.................................................       2070-0112
761.180.................................................       2070-0112
761.185.................................................       2070-0008
761.187.................................................       2070-0008
761.193.................................................       2070-0008
761.202.................................................       2070-0112
761.205.................................................       2070-0112
761.207.................................................       2070-0112
761.207(a)..............................................       2050-0039
761.208.................................................       2070-0112
761.209.................................................       2070-0112
761.210.................................................       2070-0112
761.211.................................................       2070-0112
761.215.................................................       2070-0112
761.218.................................................       2070-0112
------------------------------------------------------------------------
                                Asbestos
------------------------------------------------------------------------
Part 763, subpart E.....................................       2070-0091
Part 763, subpart G.....................................       2070-0072
Part 763, subpart I.....................................       2070-0082
------------------------------------------------------------------------
                    Dibenzo-para-dioxin/Dibenzofurans
------------------------------------------------------------------------
766.35(b)(1)............................................       2070-0054
766.35(b)(2)............................................       2070-0054
766.35(b)(3)............................................       2070-0017
766.35(b)(4)(iii).......................................       2070-0054
766.35(c)(1)(i).........................................       2070-0054
766.35(c)(1)(ii)........................................       2070-0054
766.35(c)(1)(iii).......................................       2070-0017
766.35(d) Form..........................................       2070-0017
766.38..................................................       2070-0054
------------------------------------------------------------------------

[[Page 589]]

     Procedures Governing Testing Consent Agreements and Test Rules
------------------------------------------------------------------------
790.5...................................................       2070-0033
790.42..................................................       2070-0033
790.45..................................................       2070-0033
790.50..................................................       2070-0033
790.55..................................................       2070-0033
790.60..................................................       2070-0033
790.62..................................................       2070-0033
790.68..................................................       2070-0033
790.80..................................................       2070-0033
790.82..................................................       2070-0033
790.85..................................................       2070-0033
790.99..................................................       2070-0033
------------------------------------------------------------------------
                   Good Laboratory Practice Standards
------------------------------------------------------------------------
Part 792................................................      2010-0019,
                                                              2070-0004,
                                                              2070-0017,
                                                              2070-0033,
                                                              2070-0054,
                                                               2070-0067
------------------------------------------------------------------------
                       Provisional Test Guidelines
------------------------------------------------------------------------
795.45..................................................       2070-0067
795.232.................................................       2070-0033
------------------------------------------------------------------------
    Identification of Specific Chemical Substance and Mixture Testing
                              Requirements
------------------------------------------------------------------------
799.1053................................................       2070-0033
799.1250................................................       2070-0033
799.1560................................................       2070-0033
799.1575................................................       2070-0033
799.1645................................................       2070-0033
799.1700................................................       2070-0033
799.2155................................................       2070-0033
799.2325................................................       2070-0033
799.2475................................................       2070-0033
799.2500................................................       2070-0033
799.2700................................................       2070-0033
799.3300................................................       2070-0033
799.4360................................................       2070-0033
799.4440................................................       2070-0033
799.5000................................................       2070-0033
799.5025................................................       2070-0033
799.5050................................................       2070-0033
799.5055................................................       2070-0033
799.5075................................................       2070-0033
------------------------------------------------------------------------
\1\ The ICRs referenced in this section of the table encompass the
  applicable general provisions contained in 40 CFR part 60, subpart A,
  which are not independent information collection requirements.
\2\ The ICRs referenced in this section of the table encompass the
  applicable general provisions contained in 40 CFR part 61, subpart A,
  which are not independent information collection requirements.
\3\ The ICRs referenced in this section of the table encompass the
  applicable general provisions contained in 40 CFR part 63, subpart A,
  which are not independent information collection requirements.

[58 FR 27472, May 10, 1993]

    Editorial Note: For Federal Register citations affecting Sec. 9.1 
see the List of CFR Sections Affected in the Finding Aids section of 
this volume.

[[Page 591]]



List of CFR Sections Affected



All changes in this volume of the Code of Federal Regulations which were 
made by documents published in the Federal Register since January 1, 
1986, are enumerated in the following list. Entries indicate the nature 
of the changes effected. Page numbers refer to Federal Register pages. 
The user should consult the entries for chapters and parts as well as 
sections for revisions.
Title 40 was established at 36 FR 12213, June 29, 1971. For the period 
before January 1, 1986, see the ``List of CFR Sections Affected, 1964--
1972 and 1973-1985'' published in six separate volumes.

                                  1986

40 CFR
                                                                   51 FR
                                                                    Page
Chapter I
52  State implementation plans disapproval..........................2399
    State implementation plan deficiency notice.....................3046
    Restrictions lifted............................................39375
52.07  (a) amended.................................................40676
52.10  Amended.....................................................40677
52.20  Amended.....................................................40676
52.21  (l) revised.................................................32179
    Technical correction...........................................34086
    (f)(1) and (g)(2)(i) amended...................................40675
    (b)(2)(iii)(e)(1), (2), (f), (17) and D(f)(13) amended.........40677
52.24  (f)(5)(iii)(e) (1) and (2), (f), (6)(iii) and (v)(c), and 
        (12), and (i)(2) amended...................................40677
52.50  (c)(40) added................................................4909
    (c)(41) added; (c) introductory text republished...............25199
    (c)(42) added..................................................25367
    (c)(44) added..................................................45470
    (c)(38) added..................................................46658
52.54  Table amended...............................................25367
52.55  (a) amended..........................................40675, 40676
52.57  (a) amended.................................................40676
52.59  (a) amended.................................................40676
52.70  (c)(12) added...............................................32639
52.73  (a) amended.................................................40676
52.74  (a) introductory text, (1) (i), (ii), (iii), and (iv), and 
        (2) (i), (ii), (iii), (v), and (vi), (b) and (c) amended 
                                                                   40676
52.75  Revised.....................................................32639
52.76  Removed.....................................................32640
52.78  (a) amended.................................................40677
52.80  (a) amended.................................................40677
52.84  (b) and (d)(10) amended.....................................40676
    (a) amended....................................................40677
52.85--52.93  Removed..............................................32640
52.88  (a)(5) amended..............................................40677
52.89  (a)(4) amended..............................................40677
52.90  (a)(3) amended..............................................40677
52.91  (a)(3) amended..............................................40677
52.95  (a) and (b) amended.........................................40676
52.123  (c) revised; (e)(2) and (3) added...........................3336
    (c)(1) and (2) removed; (c)(3) redesignated as (c)(1); (b) and 
(e)(1) and (2) revised.............................................33750
52.124  (a)(1) and (2) revised.....................................33750
    (a)(2) revised..................................................3337
52.125  (a)(1) and (b) amended..............................40676, 40677
52.126  (a) amended................................................40676
    (a) and (c) amended............................................40677
52.129  (b) and (e) amended........................................40677
52.130  (a), (b), (d) and (e) amended..............................40677
52.133  (c) amended.........................................40676, 40677
52.135  (a) amended................................................40677
52.143  (a) amended................................................40676
52.170  (c)(23) added..............................................27841
    (c)(24) added..................................................40976
    (c)(22) added...................................................4912
52.175  (a) amended................................................40677
52.178  Removed....................................................27841
    (a) amended....................................................40676
52.179  Removed....................................................27841
    (a) amended....................................................40676
52.182  (a) and (b) amended........................................40676
52.220  (c)(154)(vi)(B) and (vii)(B) added...........................603

[[Page 592]]

    (c)(163) added..................................................8496
52.224  (a) amended................................................40676
52.225  (a) and (b) amended........................................40676
52.227  (a) amended................................................40676
52.230  (a) amended................................................40677
52.232  (a)(1)(i) and (5)(i)(A)   amended..........................40677
52.233  (l) and (m) added...........................................8496
    (c) and (d) amended............................................40677
52.234  (a), (b), (c) and (e) amended..............................40677
52.235  Removed....................................................40677
52.240  (f)(1) amended.............................................40675
    (b), (e), and (f) (1) and (2) amended..........................40676
    (a) amended....................................................40677
52.255  (g) amended................................................40676
52.256  (i) amended................................................40676
52.267  (a) amended................................................40676
52.269  (a) amended................................................40676
52.272  (a) amended................................................40677
52.274  (a), (b), (e), (h) and (q) amended.........................40677
52.320  (c)(35) added..............................................12321
    (c)(36) and (37) added.........................................31126
    (c)(30) added..................................................43610
52.324  (a) and (c) amended........................................40676
52.341  (a) amended................................................40676
52.343  (a) revised................................................31126
52.370  (c)(36) added..............................................41964
52.379  (a) amended................................................40676
52.420  (c)(35) added..............................................44068
52.426  (a) amended................................................40677
52.429  (a) amended................................................40676
52.431  (a) and (b) amended........................................40676
52.470  (c)(26) added..............................................12323
52.479  (b) amended................................................40677
52.497  (a) amended................................................40675
    (a) and (b) amended............................................40676
52.520  (c)(58) added...............................................2698
52.524  (b)(7) and (c) amended.....................................40676
    (a) amended....................................................40677
52.525  (a) amended................................................40676
52.526  (a) amended................................................40676
52.529  (a) amended................................................40676
52.534  Revised.....................................................5505
52.570  (c)(32) added...............................................3468
52.574  (a) amended................................................40677
52.576  (b) added...................................................3778
    (a) amended.............................................40675, 40676
52.580  (a) amended................................................40676
52.624  (a) amended................................................40676
52.625  (a) amended................................................40676
52.626  (a) and (b) amended........................................40676
52.629  (a) amended................................................40677
52.631  (a) and (b) amended........................................40676
52.670  (c)(24) added; eff. 8-22-86................................22810
52.674  (a) amended................................................40676
52.675  (a)(1) amended.............................................40676
52.676  (a)(1) amended.............................................40676
52.677  (b) amended................................................40675
    (b) and (c) amended............................................40676
    (a) amended....................................................40677
52.679  Revised; eff. 8-22-86......................................22810
52.681  Added; eff. 8-22-86........................................22811
52.682  (a) amended................................................40676
52.683  Revised; eff. 8-22-86......................................22812
52.688  Revised; eff. 8-22-86......................................22812
    (b)(2) amended.................................................40677
52.690  Correctly designated.......................................23759
52.720  (c)(63) added..............................................10837
    (c)(64) added..................................................15616
    (c)(65) added..................................................15617
52.729  (a) amended................................................40676
52.730  (c) amended................................................40675
    (b)(4), (c), and (d) amended...................................40676
    (a) amended....................................................40677
52.735  (a) and (b) amended........................................40676
52.770  (c)(57) added...............................................2498
    (c)(55) added...................................................4915
    (c)(54) added...................................................5519
    (c)(57) corrected..............................................11306
    (c)(56) added..................................................15618
    (c)(58) added; eff. 7-3-86.....................................19834
    (c)(66) added; eff. 7-7-86.....................................20285
    (c)(59) added..................................................42223
52.771  (b), (c), and (d) amended..................................40675
52.773  (f) revised.................................................4916
52.775  (a) introductory text and (1) (i) and (ii), (2) (i), (ii), 
        and (iii), (3) (i) and (ii), (4) (i) and (ii), (5) (i) and 
        (ii), (6) (i) and (ii), (7) (i), (ii), and (iii), (8) (i) 
        and (ii), (9) (i), (ii), and (iii), and (10) (i), (ii), 
        and (iii) and (a)(11)(i) amended...........................40676
52.776  (j) added...................................................2498
    (j) correctly designated.......................................11306
    (a) amended....................................................40676
52.777  (c) introductory text and (1) introductory text revised; 
        (c)(1)(ii), (iii), (iv), (vi), (vii), (viii) removed........4916
    (a) and (b) amended............................................40676
52.778  (c) amended................................................40675
    (c) and (d) amended............................................40676
    (a) amended....................................................40677
52.780  (a) and (e) amended........................................40677
52.782  (a) amended................................................40677
52.784  (a) amended................................................40676

[[Page 593]]

52.785  (a) amended................................................40676
52.786  (a)(3) amended.............................................40677
52.792  (a) and (b) amended........................................40676
52.794  (b) amended................................................40676
    (a) and (b) amended............................................40677
52.795  (c) amended................................................40676
    (b) amended....................................................40677
52.796  (a) amended................................................40677
52.820  (c)(45) added..............................................25200
52.823  Removed....................................................25200
52.825  (c) amended.........................................40675, 40676
52.828  (b)(1)(iii) amended.................................40675, 40677
    (b)(1) (i) and (iii) amended...................................40676
52.832  (a) amended................................................40676
52.870  (c)(17) added..............................................25202
52.874  (a), (b) introductory text, (1)(i), (2)(i), and (3)(i) and 
        (c) amended................................................40676
52.876  (c) (1) and (2) amended.............................40675, 40676
    (a) amended....................................................40677
52.878  (a) amended................................................40677
52.883  (a) and (b) amended........................................40676
52.920  (c)(45) added..............................................43744
52.924  (a) amended................................................40676
52.925  (a) amended................................................40676
52.927  (c) amended................................................40675
    (b)(6) and (c) amended.........................................40676
    (a) amended....................................................40677
52.929  (a) amended................................................40676
52.930  (b)(2) added...............................................10210
52.935  (a)(1) (ii), (iii), (iv), (vi), (vii), (viii), and (ix) 
        removed; (a)(1)(v) redesignated as (a)(1)(ii)..............43744
52.936  Added.......................................................5505
52.970  (c)(42) added..............................................12854
    (c)(43) added; eff. 7-10-86....................................20969
52.978  (a) amended................................................40677
52.980  (a), (b), (c), and (d) amended......................40675, 40676
52.988  (a) amended................................................40677

                                  1987

40 CFR
                                                                   52 FR
                                                                    Page
Chapter I
52  State Implementation Plan inadequacy............................1908
    State Implementation Plan approval.......................4292, 45634
    State Implementation Plan clarification........................11647
    State implementation plan attainment groups....................29383
    State implementation plan deficiency notices............34384, 47565
52.21  (b)(23)(i) table, (c) table, (i)(8)(i), and (p)(5) table 
        amended; (i)(4) (ix) and (x), (11), and (m)(1) (vii) and 
        (viii) added; (w)(2) revised; eff. 7-31-87.................24714
    (m)(1)(vii) corrected..........................................26401
52.24  (i)(2) corrected; (j)(2) amendment at 51 FR 40677 correctly 
        removed....................................................24367
    (f)(10) amended; eff. 7-31-87..................................24715
52.27  (d)(2) revised; (d) (3), (4), and (5) added.................45137
52.29  Added.......................................................45137
52.50  Technical correction.........................................2007
    (c)(45) added...................................................4291
    (c)(46) added..................................................28254
52.54  Table amended................................................4291
52.58  Amended......................................................4291
52.60  (c) redesignated as (a); (b) added..........................48812
52.61  Added.......................................................45138
52.74  (a)(2)(vi) corrected; (a)(2)(iv) amendment at 51 FR 40676 
        correctly removed..........................................24367
52.145  (c) added..................................................45137
52.183  Added......................................................45138
52.220  (c)(153)(vii)(B), (156)(vii), (166) and (167) added.........1628
    (c)(168) added..................................................3228
    (c)(124)(vi)(B), (vii)(B), (viii)(B), (ix)(B), and (x)(B) 
revised; (c) (164) and (165) added; (c)(6) amended.................12523
    (c)(154)(v)(B), (159) (ii) through (vi) and (160) added; 
(c)(159) introductory text republished.............................26149
52.232  (a)(3)(ii) through (v) and (11)(ii) removed.................1628
52.279  Added.......................................................3646
52.281  (e) added..................................................45138
52.320  (c)(33) added; eff. 8-21-87................................23447
52.343  (a)(1) and (8) and (b) correctly revised; (a)(9) correctly 
        added.......................................................4622
    (a)(10) correctly added........................................22638
52.344  (c) added..................................................45137
52.370  (c)(37) added...............................................5105
    (c)(39) added..................................................47925
52.383  Added......................................................49407
52.420  (c)(37) added..............................................48813
52.520  (c)(59) added...............................................3431
    (c)(62) added..................................................35704

[[Page 594]]

52.581  (c) redesignated as (a); new (b) added.....................32918
52.633  (c) added..................................................45137
52.690  (c) added..................................................45137
52.720  (c)(68) added...............................................1455
    (c)(67) added...................................................2225
    (c)(73) added...................................................8071
    (c)(74) added..................................................16386
    (c)(69) added..................................................45334
52.726  (c) added..................................................26012
52.770  (c) (53) and (61) added.....................................3644
    (c)(60) added...................................................4905
    (c)(62) added..................................................12911
    (c)(36) removed; (c)(53) revised; eff. 7-17-87.................23038
    (c)(63) added..................................................33591
    (c)(64) added..................................................46763
52.775  (a)(11)(i) corrected.......................................24367
52.776  (l) added...................................................3644
    (k) added.......................................................4905
    (m) added; eff. 7-17-87........................................23038
52.777  (c)(1)(i) removed..........................................33591
52.794  (c) added...................................................3644
    (b) removed; (c) revised; eff. 7-17-87.........................23038
52.820  (c)(46) added; eff. 8-25-87................................23982
52.828  (b)(1)(i) corrected........................................24367
52.833  Revised; eff. 8-25-87......................................23982
52.870  (c)(18) added.................................................54
    (c)(19) added..................................................48265
52.920  (c)(48) added...............................................3116
    (c)(47) added..................................................33593
    (c)(51) added..................................................45959
52.970  (c)(44) added..............................................13673
52.986  Revised....................................................13673
52.989  Added......................................................45138

                                  1988

40 CFR
                                                                   53 FR
                                                                    Page
Chapter I
52  State implementation plan disapproval; eff. 7-5-88.............20321
    State implementation plan inadequacy notice.............34500, 48642
    Petition denied................................................52705
52.21  (l) (1) and (2) revised.......................................396
    (b)(3)(iv), (13)(i), (ii) (a), and (b), (14)(i), (15)(i), 
(ii)(a), (c) tables, (f)(1)(v), (4)(i), and (p)(5) tables revised; 
(b)(14)(ii) redesignated as (b)(14)(iii); new (b)(14)(ii), 
(i)(12), and OMB number added; (p)(5) amended; eff. 11-19-90.......40671
52.50  (c)(48) added...............................................47689
52.120  (c)(54)(i) (D) and (E), (56)(i)(B), (58) through (62), 
        (64) and (66) added........................................30223
    (c) (55), (57), (60)(i)(B), (62)(i)(A)(2), (65) and (66)(i)(B) 
added..............................................................30238
52.124  (a)(2) removed.............................................30224
    (a)(1) removed.................................................30238
52.170  (c)(25) added..............................................27517
52.183  Removed....................................................27517
52.237  (a)(1) added................................................1781
    (a)(2) added...................................................39088
    (a)(3) added...................................................48537
52.320  (c)(39) added..............................................27859
    (c)(38) added..................................................30428
    (c)(41) added..................................................30431
    (c)(42) added..................................................38289
    (c)(40) added..................................................48539
52.344  (c) removed................................................30431
    (b) revised....................................................48539
52.370  (c)(41) added...............................................4622
    (c)(42) added..................................................11847
    (c)(38) added..................................................17936
    (c)(44) added..................................................26257
    (c)(43) added..................................................28885
52.375  (d) added..................................................17936
52.520  (c)(53) added..............................................10076
52.570  (c)(35) added..............................................25330
    (c)(34) added..................................................26253
    (c)(36) added..................................................29891
52.670  (c)(25) added..............................................48540
52.679  Revised....................................................48540
52.720  (c)(70) added...............................................4139
52.726  (c) added..................................................40426
52.770  (c)(66) added...............................................1358
    (c)(65) added..................................................12904
    (c)(66) amended; (c)(67) added.................................33811
    (c)(70) added..................................................38722
    (c) (68) and (69) added........................................46613
    (c)(67)(i)(H) removed; (c)(71) added...........................50523
52.773  (b) amended; (h) added.....................................33811
    (i) added......................................................46613
52.777  (c) introductory text amended; (d) added...................46613
52.793  (c) revised................................................18985
52.795  (d) removed.................................................1358
52.797  Added......................................................12905
52.797  (a) removed; (c) added.....................................38722
52.820  (c)(47) added..............................................41601
52.870  (c)(20) added..............................................17701
    (c)(21) added..................................................31861
    (c)(22) added..................................................43692
    (c)(23) added..................................................47691

[[Page 595]]

52.879  Table revised..............................................43692
52.920  (c)(50) added................................................502
    (c)(53) added..................................................11656
    (c)(55) added; eff. 7-21-88....................................23238
    (c)(52) added..................................................26256
    (c)(54) added..................................................30999
52.970  (c)(45) added..............................................36010
    (c)(47) added..................................................50961
52.989  Removed....................................................50961
52.990  Added......................................................36010

                                  1989

40 CFR
                                                                   54 FR
                                                                    Page
Chapter I
52  State implementation plan inadequacy notice...............5449, 6287
    State implementation plan approval.......................7765, 10323
    PM 10 grouping revision........................................12620
    State implementation plan disapproval...................13383, 13682
    Stack height declarations.....................................14221,
                                                     19172, 30040, 32073
    State implementation plan determinations........32072, 33531, 43812, 
                                                            43816, 46612
    Air quality implementation plans...............................48870
    Authority delegation notices............................22888, 23978
    Petition denied................................................23479
52.21  (b)(17) revised.............................................27285
    (b)(30) and (v)(2)(vi) added; (v)(2)(iv)(b) removed; 
(v)(2)(iv)(c) redesignated as (v)(2)(iv)(b)........................27300
52.23  Amended.....................................................27285
52.24  (f)(12) revised.............................................27285
    (f)(18) added..................................................27300
52.55  Removed.....................................................25258
52.62  Added.......................................................51400
52.70  (c)(14) added................................................8537
    (c)(15) added..................................................31523
    (c)(13) added; eff. 7-25-89....................................22755
52.75  Revised......................................................8537
    Revised; eff. 7-25-89..........................................22755
    Revised........................................................31523
52.84  (b) removed.................................................25258
52.134  (b) removed................................................25258
52.170  (c)(26) added...............................................7765
    (c)(27) added..................................................18495
52.181  Revised....................................................18495
52.220  (c) (173) and (174) added...................................5449
    (c) (169) and (170) added......................................14226
    (c) (171) and (172) added......................................14650
    (c)(175) added.................................................15181
    (c)(169) removed...............................................26374
    (c)(176) added.................................................43176
    (c)(176)(i) (B) and (C) added..................................43174
52.229  (b)(2)(iii) added...........................................5237
    (b)(2)(ii) added...............................................34515
52.240  (e) and (f)(1) removed.....................................25258
52.269  (b)(2)(ii) and (iii) added..................................5237
52.320  (c)(44) added...............................................9781
    (c)(47) added..................................................13183
    (c)(48) added; eff. 7-10-89....................................20390
    (c)(43) added; eff. 7-31-89....................................22893
    (c)(45) added; eff. 7-7-89.....................................24340
    (c)(48) removed................................................29310
52.331  Added......................................................43178
52.343  (c) added..................................................27881
52.345  Added; eff. 7-7-89.........................................24340
52.370  (c)(48) added...............................................9782
    (c)(46) added..................................................12195
    (c)(49) added..................................................14227
    (c)(50) added; eff. 7-31-89....................................22892
    (c)(50) added..................................................23661
    (c)(51) correctly designated...................................29893
    (c)(47) added..................................................48887
    (c)(52) added..................................................49285
    (c)(53) added..................................................52799
52.429  Removed....................................................25258
52.520  (c)(60) added...............................................6126
    (c)(65) added..................................................30892
52.524  (c) removed................................................25258
52.528  (a) added; eff. 7-17-89....................................25455
52.576  (a) removed................................................25258
52.578  Added; eff. 7-17-89........................................25452
    Revised........................................................40002
52.626  (a) removed................................................25258
52.677  (b) removed................................................25258
52.730  (c) removed................................................25258
52.770  (c)(72) added; (c)(66)(i)(A), (67) introductory text, (i) 
        (A), (B), (C), (D), and (G), and (71) introductory text 
        and (i)(C) revised; (c)(66)(i)(B), (67)(i)(H), and 
        (71)(i)(D) removed; (c)(66) introductory text amended.......2117
    (c)(78) added..................................................33896
    (c)(74) revised................................................46612
52.773  (b) removed and reserved; (h) revised.......................2118
52.778  (c) removed................................................25258
52.795  (e) removed.................................................2118
52.797  (b) removed................................................33896
52.820  (c)(48) added..............................................29895
    (c)(50) added..................................................33528

[[Page 596]]

    (c)(49) added..................................................33530
    (c)(51) added..................................................33539
52.823  Added......................................................33539
52.825  Table amended..............................................25258
52.827  Table revised..............................................33539
    Table footnote g corrected.....................................37187
52.870  (c)(24) added..............................................15935
    (c)(25) added..................................................29894
    (c)(25) removed................................................43812
52.876  (c)(1) removed.............................................25258
52.884  (b) removed................................................15935
52.920  (c)(57) added...............................................7930
    (c)(58) added...................................................7931
    (c)(58) correctly designated...................................10214
    (c)(59) added..................................................15933
    (c)(60) added; eff. 7-3-89.....................................19172
    (c)(61) added..................................................18104
    (c)(49) added..................................................35328
    (c)(46) added..................................................36311
    (c)(56) added..................................................46613
    (c)(62) added..................................................47077
    (c)(65) added..................................................47211
    (c)(63) added..................................................48888
52.927  (c) removed................................................25258
52.930  (a) added..................................................10983
52.931  (a) removed; (b) and (c) redesignated as (a) and (b) and 
        revised; new (c) added.....................................36311
52.933  Added; eff. 7-3-89.........................................23478
52.935  Removed; eff. 7-3-89.......................................19172
52.936  Revised....................................................36311
52.970  (c)(48) added...............................................9795
    (c) (20) through (48) redesignated as (c) (21) through (49).....9796
    (c)(46) added..................................................12196
    (c)(50) added; eff. 8-14-89....................................25451
    (c)(51) added; eff. 7-27-89....................................27004
    (c)(50)(i)(B) added............................................29896
    (c)(52) added..................................................41444
    (c)(53) added..................................................48743
52.980  (a) and (b) removed........................................25258
52.986  Revised.....................................................9795
52.988  Revised.....................................................9796

                                  1990

40 CFR
                                                                   55 FR
                                                                    Page
Chapter I
52  State implementation plan determinations.......................3594,
    6253, 9726, 10061, 12823, 19065, 19066, 23549, 24080, 29846, 33692, 
                                                     34915, 39148, 51101
    Petition denied.................................................7713
    State implementation plan determinations; eff. 7-2-90..........22334
    Visibility impairment assessment...............................24060
    State implementation plans; policy guidance....................38326
    Technical correction...........................................40996
52.50  (c)(50) added................................................2236
    (c)(51) added..................................................10063
    (c)(49) added..................................................17435
    (c)(52) added..................................................38996
    (c)(47) added..................................................39405
52.54  Table amended...............................................17435
52.62  Revised......................................................5846
52.146  (c) and (d) added..........................................17437
    Added..........................................................18108
52.220  (c)(176)(i)(B) and (C) correctly designated................22334
    (c)(154)(vii)(B) removed.......................................25833
    (c)(168)(i)(A)(2), (C)(2), (E)(2), (F), (G), and (H) added.....28624
    (c)(159)(iv)(B), (v)(C), (D), (vii), (160)(i)(D), and (E) 
added..............................................................28625
    (c)(177) added.................................................31833
    (c)(177)(i)(A)(2), (B)(1), and (C)(1) added....................31835
    (c)(179) added.................................................49283
52.232  (a)(5)(iii) removed.........................................9878
52.237  (a)(5) added................................................9878
    (a)(4) added....................................................9880
52.279  (a)(2) revised.............................................31835
52.320  (c)(46) added...............................................9125
52.370  (c)(54) added...............................................9122
    (c)(55) added...................................................9444
52.420  (c)(38) added...............................................2067
    (c)(41) added...................................................3402
    (c)(39) added; eff. 7-30-90....................................26689
52.520  (c)(66) added...............................................3406
    (c)(68) added..................................................12823
    (c)(71) added..................................................46790
52.634  Added; eff. 7-2-90.........................................18110
52.720  (c)(71) added..............................................14421
    (c)(78) added; eff. 7-30-90....................................26909
    (c)(81) added..................................................29203
    (c)(79) added..................................................40661
52.722  Revised....................................................40661
52.725  (c) added; eff. 7-16-90....................................20266
52.726  (d) correctly designated...................................21751
    (e) added; eff. 7-30-90........................................26909
52.741  Added; eff. 7-30-90........................................26856
    (a)(3), (4)(i)(B)(3), (v)(B), (8)(ii), (e)(1)(i) table, 
(ii)(C)(1), (2), (iii), (h), (1)(ii)(A), (4)(i)(A)(2), (ii)(A), 
(C)(2), (q)(1)(v)(A), (B), (u)(3)(ii), (v)(1)(i) and Appendix B 
corrected..........................................................31981
    (a)(8)(ii), (h)(1)(ii)(A) and Appendix B corrected......39774, 39775

[[Page 597]]

52.742  Added; eff. 7-30-90........................................26909
52.770  (c)(83) added..............................................18604
    (c)(84) and (85) added.........................................31051
    (c)(86) added..................................................34261
    (c)(76) added..................................................36635
    (c)(80) added..................................................39151
52.773  (d) and (e) removed; (j) added.............................31052
52.776  (n) added; eff. 8-13-90....................................23932
52.786  (h) removed................................................31052
52.820  (c)(49)(i)(A) and (50)(i)(A) correctly revised; eff. 8-28-
        90.........................................................26691
    (c)(52) added; eff. 8-28-90....................................26690
    Correctly designated...........................................26691
52.870  (c)(25) added...............................................1422
52.879  Table revised...............................................1422
52.881  Added.......................................................1423
52.920  (c)(64) added...............................................3594
    (c)(59) revised.................................................3593
    (c)(66) added...................................................4171
    (c)(67) added..................................................20269
52.935  Added.......................................................4172
52.970  (c)(54) added...............................................3598
    Second (c)(46) correctly removed...............................21547
    (c)(55) added..................................................29205
    (c)(56) added..................................................36811
52.979  Revised.....................................................1023

                                  1991

40 CFR
                                                                   56 FR
                                                                    Page
Chapter I
52  Authority delegation notices....................................4944
    Petitions denied...............................................14862
    State implementation plan determinations.......................28086
52  State implementation plan determinations.........52476, 54789, 65441
    Authority delegation notice....................................67197
52.21  (b)(23)(i) amended; eff. 8-12-91.............................5506
52.50  (c)(53) added...............................................32514
52.63  Added.......................................................32514
52.70  (c)(16) added...............................................19287
    (c)(17) added..................................................43085
52.75  Revised.....................................................19287
52.96  (a) revised.................................................19288
52.120  (c)(63), (65)(i)(A)(2) and (66)(i)(D) added.................3221
52.124  Added.......................................................5478
52.136  Added.......................................................5478
52.137  Added.......................................................5482
52.138  Added.......................................................5485
52.145  (d) added..................................................50186
52.170  (c)(28) added..............................................20139
52.181  Revised....................................................20139
52.220  (c)(177)(D) added..........................................15287
    (c)(184) added.................................................41285
52.237  (a)(4) and (5) revised......................................2853
52.320  (c)(49) added..............................................11674
    (c)(51) added..................................................12851
    (c)(53) added..................................................15500
52.370  (c)(58) added..............................................52210
52.420  (c)(42) added..............................................13078
52.520  (c)(70) added..............................................11675
    (c)(72) added..................................................51984
52.531  Added......................................................51984
52.741  (z) added....................................................462
    (z) revised....................................................24723
    (z)(2) added...................................................33712
    (z)(3) added...................................................33714
    (z)(1) amended; (z)(4) added...................................58503
52.820  (c)(53) added...............................................5758
    (c)(54) added..................................................56159
    (c)(55) added..................................................60925
52.970  (c)(57) added..............................................20139
52.986  Revised....................................................20139

                                  1992

40 CFR
                                                                   57 FR
                                                                    Page
Chapter I
52  Authority citation revised................27936, 27939, 27942, 32336
    State implementation plan determination.................44689, 45715
    Authority delegation notice....................................54931
52.21  (b)(30) revised..............................................3946
    (b)(21)(iv) revised; (b)(2)(iii)(h) through (k), (21)(v) and 
(31) through (38) added............................................32336
52.24  (f)(18) revised..............................................3946
    (f)(13)(iv) revised; (f)(5)(iii)(h), (i), (13)(v) and (19) 
through (24) added.................................................32337
52.50  (c)(58) added; eff. 8-10-92.................................24370
52.65  Added; eff. 8-10-92.........................................24370
52.120  (c)(67) added................................................355
    (c)(68) added...................................................8271
52.136  Removed.....................................................8271
52.137  Removed.....................................................8271
52.220  (c)(183) and (184)(i)(B) added.............................10138
    (c)(185) added.................................................15029
    (c)(177)(E) added; eff. 7-10-92................................24550
    (c)(183)(i)(C), (185)(i)(A)(2), (B)(2) and (187) added; eff. 
8-24-92............................................................28090

[[Page 598]]

    (c)(183)(i)(B)(2), (184)(i)(B)(2), (C)(1), (185)(i)(A)(3) and 
(C)(2) added.......................................................35759
    (c)(182), (183)(i)(A)(2), (184)(i)(B)(2)  added................48459
52.320  (c)(54) added; eff. 7-17-92................................27000
    (c)(58) added; eff. 7-24-92....................................28092
    (c)(55) added; eff. 8-25-92....................................28617
    Regulation at 57 FR 28617 withdrawn............................36004
    (c)(57) added..................................................40333
    (c)(56) added..................................................54511
52.329  (a)(1), (2) and (3) revised; (a)(4) removed; eff. 7-17-92 
                                                                   27000
52.343  (a)(1), (3) and (8) revised; eff. 7-17-92..................27000
52.370  (c)(61) added..............................................10140
    (c)(59) added..................................................54705
52.420  (c)(43) added................................................353
    (c)(44) added..................................................53566
52.470  (c)(27) added..............................................34251
52.472  (d) added..................................................34251
52.520  (c)(73) added...............................................7552
    (c)(69) added; eff. 8-10-92....................................24371
    (c)(74) added; eff. 8-10-92....................................24379
52.570  (c)(40) added; eff. 8-10-92................................24373
    (c)(37) added..................................................46781
    (c)(38) added..................................................58991
52.720  (c)(83) added..............................................10142
    (c)(83) removed................................................24957
    (c)(86) added; eff. 7-26-92....................................28618
    (c)(90) added..................................................37104
    (c)(88) added..................................................40128
    (c)(87) added..................................................40335
    (c)(84) and (85) added.........................................59935
    (c)(94) added..................................................61837
52.736  (a) removed; (b) added.....................................59935
52.737  Added......................................................59936
52.741  (a)(3) amended..............................................3946
    (z)(3) revised..................................................7550
    (z)(1) and (4) revised.........................................27936
    (z)(5) added...................................................38616
52.770  (c)(87) added...............................................8086
    (c)(81) added..................................................42892
52.777  (c)(2) added................................................8086
52.820  (c)(56) added...............................................2473
52.870  (c)(26) added; eff. 7-23-92................................27939
52.873  Existing text designated as (a); (b) added; eff. 7-23-92 
                                                                   27939
52.970  (c)(58) added...............................................8076

                                  1993

40 CFR
                                                                   58 FR
                                                                    Page
Chapter I
52  Authority citation revised; eff. 8-19-93.......................38883
    Authority delegation notice....................................43798
      Technical correction............................6056, 34904, 61143
    State implementation plan determinations.........6606, 11967, 28361, 
                  33340, 33914, 41430, 42671, 50516, 52237, 64678, 65286
    OMB number.....................................................34370
52.21  (b)(3)(iv), (c) table, (p)(5) table and (i)(8)(i) revised; 
        (f) removed; (b)(14)(iv), (15)(iii) and (i)(13) added; 
        eff. 6-3-94................................................31637
    (l)(1) revised; (l)(2) amended; eff. 8-19-93...................38883
52.50  (c)(60) added...............................................25567
    (c)(61) added..................................................45440
    (c)(56) and (57) added.........................................50266
52.219  Added......................................................62533
52.220  (c)(183)(i)(D)(1), (184)(i)(A)(2), (186)(i)(A)(1) added.....8546
    (c)(187)(i)(A)(2) added........................................15284
    (c)(183)(i)(A)(4), (C)(2), (185)(i)(A)(5), (C)(4), (D)(1) and 
(187)(i)(A)(3) added...............................................28356
    (c)(182)(i)(B)(4) added........................................28357
    (c)(183)(i)(A)(3) and (185)(i)(A)(6) added.....................28359
    Regulation at 58 FR 15284 withdrawn............................28926
    (c)(182)(i)(B)(2) and (183)(i)(A)(7) added; eff. 7-16-93.......33196
    (c)(183)(i)(A)(5) and (C)(3) added; eff. 7-16-93...............33197
    (c)(184)(i)(D)(1), (185)(i)(A)(4) and (C)(3) added; eff. 7-30-
93.................................................................34906
    (c)(183)(i)(A)(10) added; eff. 8-2-93..........................34907
    (c)(182)(i)(B)(5), (183)(i)(A)(9), (F), and (185)(i)(B)(4) 
added..............................................................37423
    (c)(183)(i)(A)(11), (C)(4) and (185)(i)(C)(6) added............45442
    (c)(179)(i)(C), (182)(i)(B)(3), (i)(C) and (183)(i)(E)(2) 
added..............................................................45443
    (c)(182)(i)(A)(2) added........................................45445
    (c)(182)(i)(A)(3) and (185)(i)(B)(5) added.....................45447
    (c)(183)(i)(A)(6) added........................................47832
    (c)(184)(i)(B)(3) added........................................50851
    (c)(181) added.................................................64158

[[Page 599]]

    (c)(182)(i)(D) added...........................................66282
    (c)(188) and (189) added.......................................66283
    (c)(188)(i)(B) added...........................................66285
    (c)(188)(i)(C), (189)(i)(A)(2) and (193) added.................66286
    (c)(188)(i)(D), (189)(i)(A)(3) and (191) added.................66287
52.320  (c)(59) added..............................................50270
52.329  (a)(3) removed.............................................50271
52.332  Added......................................................68038
52.346  Added......................................................49435
52.370  (c)(56) added..............................................10963
    (c)(62) added..................................................65932
52.382  Revised....................................................10964
52.420  (c)(45) added..............................................40066
52.422  Existing text designated as (a); (b) added.................50848
52.520  (c)(75) added..............................................15278
    (c)(59) added..................................................21543
    Regulation at 58 FR 21543 withdrawn............................33769
    (c)(76) added..................................................37660
52.531  Removed....................................................37660
52.570  (c)(42) added...............................................6095
52.670  (c)(26) and (27) added.....................................39447
52.679  Revised....................................................39448
52.681  Revised....................................................39450
52.683  Revised....................................................39450
52.720  (c)(93) added...............................................3844
    (c)(92) added...................................................3846
    (c)(89) added..................................................17783
    (c)(96) added..................................................45450
    (c)(97) added..................................................47382
    (c)(98) added..................................................48314
    (c)(95) added..................................................54294
52.726  (f) added...................................................3844
52.741  (z)(5) revised.............................................31653
    (a)(3) amended; (e)(1)(i)(J)(4) revised; (e)(1)(i)(J)(5) 
added; eff. 8-30-93................................................34908
52.743  Added......................................................17783
52.744  Added......................................................45451
52.770  (c)(90) added; eff. 7-16-93................................33203
    (c)(88) added..................................................43083
52.776  (o) added..................................................18161
52.786  (h) added..................................................62535
52.798  Added......................................................46544
52.820  (c)(55) revised.............................................6093
    (c)(57) added; eff. 7-12-93....................................27940
    (c)(58) added..................................................50268
52.870  (c)(27) added...............................................3848
52.884  (a)(2) and (3) removed......................................3848
52.920  (c)(68) added..............................................54521
52.934  Added......................................................54522
52.970  (c)(59) added..............................................38060

                                  1994

40 CFR
                                                                   59 FR
                                                                    Page
Chapter I
52  Authority citation revised.....................................39859
    Authority  delegation notice...................................26129
    State implementation plan determinations.........8867, 18753, 24054, 
         44938, 45230, 45231, 45233, 45746, 50844, 60318, 63045, 63723, 
                                                                   63724
    Technical correction..............................2649, 49004, 64612
52.30  Added........................................................1484
52.31  Added.......................................................39859
52.50  (c)(63)  added...............................................5332
    (c)(65) added..................................................39684
    (c)(64) added..................................................52916
    (c)(62) added..................................................54388
52.70  (c)(18)  added..............................................13886
52.120  (c)(69) added..............................................54522
52.220  (c)(185)(i)(C)(5)  and (187)(i)(A)(4) added.................2536
    (c)(187)(i)(A)(2)  added........................................5725
    (c)(192)  added................................................16140
    (c)(189)(i)(A)(4)  and (193)(i)(A)(2) added....................17698
    (c)(188)(i)(F)  added; eff. 7-11-94............................29732
    (c)(183)(i)(F)(2),  (186)(i)(B) and (C) added; eff. 7-25-94....32355
    (c)(186)(i)(D)(1) and (189)(i)(B)(1) added.....................39691
    (c)(192)(i)(A)(2) added........................................39692
    (c)(182)(i)(A)(4) and (189)(i)(B)(2) added.....................42165
    (c)(197) added.................................................43754
    (c)(6) and (183)(i)(A)(2) revised; (c)(41)(ii)(A)(i) added.....44324
    (c)(198) added.................................................44330
    (c)(196) added.................................................47546
    (c)(188)(i)(A)(2) added........................................48175
    (c)(184)(i)(B)(4), (187)(i)(B), (189)(i)(A)(5), (190) and 
(192)(i)(A)(3) added...............................................50499
    (c)(194)(i)(B) and (C) added...................................61546
    (c)(199)(i)(A)(1) added........................................63723
    (c)(183)(i)(C)(5), (184)(i)(E) and (188)(i)(D)(2) added........64131
    (c)(188)(i)(A)(3) added........................................64132
    (c)(183)(i)(A)(12), (187)(i)(A)(5), (C) and (195) added........64133
    (c)(194) added.................................................64332
    (c)(198)(i)(B) added...........................................64338
    (c)(186)(i)(D)(2) and (194)(i)(A)(2) added.....................64339
52.320  (c)(62)  added.............................................26128
    (c)(32) and (38) revised.......................................35036
    (c)(61) and (67) added.........................................37701

[[Page 600]]

    (c)(66) added..................................................42505
    (c)(65) added..................................................47095
    (c)(68) added..................................................47810
    (c)(60) added..................................................51379
    (c)(69) added..................................................55585
    (c)(64) added..................................................64335
52.329  (a)(1) and (2) removed; (a) revised........................42506
    (a) revised....................................................64336
52.332  Existing  text designated as (a); (b) added................26128
    (c)  added; eff. 7-11-94.......................................29734
    (e) added......................................................47095
    (d) added......................................................64336
52.343  (a)(1), (2) (3), (6), (7) and (8) removed; (a)(4), (5), 
        (9) and (10) redesignated as (a)(1), (2), (3) and (4)......42506
52.344  (a) revised................................................51379
52.347  Added.......................................................4004
52.370  (c)(63)  added..............................................2532
    (c)(65)  added; eff. 7-18-94...................................26126
52.420  (c)(47)  added.............................................16142
    (c)(50)  added; eff. 7-11-94...................................29957
52.460  Added......................................................25572
52.510  Added......................................................42168
52.520  (c)(80)  added..............................................8544
    (c)(79)  added.................................................13884
    (c)(83)  added.................................................17697
    Regulation  at 59 FR 8544 withdrawn............................21664
    (c)(82) added..................................................45978
    (c)(85) added..................................................46176
    (c)(87) added..................................................46553
    (c)(84) added..................................................51383
    (c)(78) added..................................................52918
52.582  Added......................................................46178
52.670  (c)(28) added..............................................43751
    (c)(30) added..................................................47804
    (c)(29) added..................................................61549
52.719  Added......................................................59656
52.720  (c)(99)  added..............................................4003
    (c)(37)  and (46) redesignated as (c)(43) and (47)..............5955
    (c)(103) added.................................................39688
    (c)(100) and (101) added.......................................46567
    (c)(93)(i)(B) removed..........................................64855
52.724  (g) added..................................................18753
52.726  (g) added...................................................9092
    (i) added......................................................46924
    (i) removed....................................................63255
    (f) revised....................................................64855
52.741  (e)(5) and (z)(1) revised; (e)(7) added....................14112
    (a)(2) revised.................................................46569
52.770  (c)(93)  added.............................................21945
    (c)(91)  added; eff. 8-9-94....................................29956
    (c)(92) added..................................................42509
    (c)(89) added..................................................47806
    (c)(94) added..................................................51114
    (c)(92) removed................................................55368
52.773  (i) revised................................................51114
52.776  (p) added...................................................7224
52.777  (e) added..................................................12170
    (g)  added; eff. 8-19-94.......................................31548
    (f) added...............................................35054, 54395
    (g) added......................................................36703
    Regulation at 59 FR 35054 removed..............................44040
    Regulation at 59 FR 36703 removed..............................47263
    (d) revised....................................................51114
52.780  (h) added..................................................51114
52.820  (c)(59) added..............................................65718
52.870  (c)(28) added; eff. 7-11-94................................24646
    (c)(29) added..................................................52427
52.873  (c) added..................................................52427
52.920  (c)(69)  added; eff. 8-22-94...............................32352
    (c)(70) added..................................................55058
52.934  Revised;  eff. 8-22-94.....................................32352
52.970  (c)(61)  added.............................................14114
    (c)(60)  added.................................................23166
    (c)(63)  added; eff. 8-22-94...................................32359
    (c)(62) added..................................................50502
52.991  Added; eff. 8-22-94........................................32360

                                  1995

40 CFR
                                                                   60 FR
                                                                    Page
Chapter I
52  State implementation plan determinations...2523, 6401, 15875, 18750, 
                  19522, 19673, 31084, 34866, 36225, 55314, 55459, 63940
52.06  (c) removed.................................................33922
52.21  (l)(1) and (2) amended......................................40474
52.22  Removed.....................................................33922
52.25  Removed.....................................................33922
52.32  Added........................................................4737
52.50  (c)(66) added................................................2029
52.52  Removed.....................................................33922
52.54  Removed.....................................................33922
52.59  Removed.....................................................33922
52.70  (c)(19) added................................................8947
    (c)(21) added..................................................17237
    (c)(23) added; eff. 8-28-95....................................33730
    (c)(20) added..................................................46024
    (c)(24) added..................................................49767
    (c)(22) added..................................................54439
52.73  Removed......................................................8948

[[Page 601]]

52.74  (a), (b) designation and (c) removed.........................8948
52.78  Removed.....................................................33922
52.80  Removed......................................................8948
52.82  Added.......................................................47280
52.81  Removed.....................................................33922
52.82  Removed.....................................................33922
52.84  Removed......................................................8948
52.95  Removed......................................................8948
52.120  (c)(67)(i)(B), (73), (74) and (77) added...................18020
    (c)(71) added; eff. 7-3-95.....................................21442
    (c)(75) added; eff. 7-7-95.....................................22524
    (c)(72) and (76) added; eff. 8-14-95...........................31412
    (c)(70) and (78) added.........................................46025
52.122  Removed....................................................33922
52.129  (e) and (f) removed; (g) redesignated as (e)...............33922
52.131  Removed....................................................33922
52.136  Added......................................................19515
52.143  Removed....................................................33922
52.170  (c)(31) added..............................................12695
52.173  Removed....................................................33922
52.176  Removed....................................................33922
52.182  Removed....................................................33922
52.183  Added......................................................12695
52.220  (c)(198)(ii) added............................................40
    (c)(194)(i)(D) and (E) added....................................2026
    (c)(191)(i)(B) added............................................4563
    (c)(198)(i)(D) added............................................5582
    (c)(198)(ii) corrected..........................................7715
    (c)(185)(i)(A)(7) and (194)(i)(F) added.........................8566
    (c)(179)(i)(D) and (190)(i)(B) added............................8949
    (c)(199)(i)(A)(4) added.........................................8950
    (c)(198)(i)(C) added...........................................12123
    (c)(199)(i)(A)(3) added........................................12453
    (c)(200) added.................................................15062
    (c)(189)(i)(C), (199)(i)(A)(6) and (210) added.................15066
    (c)(202)(i)(C), (207) and (208) added..........................15242
    (c)(197)(i)(B), (199)(i)(A)(5), (202) introductory text and 
(i) added..........................................................16801
    (c)(189)(i)(A)(6) added........................................18751
    (c)(199)(i)(A)(2) added........................................20432
    (c)(211) added.................................................21047
    (c)(206) added.................................................21456
    (c)(191)(i)(C) and (198)(i)(E) added...........................21703
    (c)(205)(i)(B) and (212) added.................................27040
    (c)(214), (215) and (216) added; eff. 8-14-95..................31084
    (c)(198)(i)(C)(2) added; eff. 7-13-95..........................31086
    (c)(216)(i)(B) added; eff. 8-22-95.............................32606
    (c)(217) and (218) added; eff. 7-24-95.........................32611
    (c)(217)(i)(B) added...........................................36069
    (c)(215)(i)(A)(3), (219), (220) and (222) added................36230
    (c)(214)(i)(B), (215)(i)(A)(2) and (B) added...................40286
    (c)(223) added.................................................43017
    (c)(204) added.................................................43383
    (c)(207)(i)(B) and (C) added...................................43386
    (c)(194)(i)(A)(3), (196)(i)(B) and (202)(i)(E) added...........43714
    (c)(198)(i)(H)(1) added........................................46222
    (c)(188)(i)(D)(3), (198)(i)(C)(3), (202)(i)(C)(2), 
(208)(i)(A)(2) and (210)(i)(B) added...............................46536
    (c)(198)(ii) removed...........................................47076
    (c)(222)(i)(B) added...........................................47275
    (c)(183)(i)(A)(13) added.......................................49512
    (c)(193)(i)(B), (199)(i)(B), (202)(i)(D) and (207)(i)(D) added
                                                                   49775
    (c)(198)(i)(F) added...........................................54597
    (c)(225) added.................................................55314
    (c)(204)(i)(A)(5) added........................................64127
52.222  Removed....................................................33922
52.222  Added......................................................47076
52.235  Added......................................................20237
52.238  Removed....................................................33922
52.267  Removed....................................................33922
52.320  (c)(70) added..............................................28060
52.322  Removed....................................................33922
52.322  Added......................................................52315
52.325  Removed....................................................33922
52.326  Added......................................................40291
52.341  Removed....................................................33922
52.370  (c)(66) added...............................................2525
    (c)(68) added..................................................47081
    (c)(69) added..................................................55320
52.372  Removed....................................................33922
52.376  Added......................................................55320
52.379  Removed....................................................33922
52.381  Added.......................................................4737
52.420  (c)(46) and (51) added; eff. 7-3-95........................21713
    (c)(53) added..................................................38712
52.426  Removed....................................................33922
52.427  Removed....................................................33922
52.428  Removed....................................................33922
52.430  Added......................................................47084
52.431  Removed....................................................33922
52.433  Added.......................................................4737

[[Page 602]]

52.470  (c)(28) added...............................................5135
    (c)(33) added; eff. 7-3-95.....................................21455
    (c)(32) added; eff. 7-25-95....................................27891
    Regulation at 60 FR 21455 withdrawn............................28339
    (c)(34) added..................................................44434
52.472  (e) added...................................................5136
    (f) added......................................................15486
52.473  Removed....................................................33922
52.480  Added......................................................47084
52.481  Removed....................................................33922
52.497  Removed....................................................33922
52.498  Added.......................................................4737
52.520  (c)(81) added.................................................45
    (c)(88) added...................................................2690
    (c)(80) added...................................................8307
    (c)(86) added..................................................10330
    (c)(89) added..................................................62753
52.523  Removed....................................................33922
52.529  Removed....................................................33922
52.570  (c)(39) added..............................................12691
    (c)(46) added..................................................45051
    (c)(48) added..................................................66150
52.574  Removed....................................................33922
52.575  Removed....................................................33922
52.577  Removed....................................................33922
52.580  Removed....................................................33922
52.622  Removed....................................................33922
52.628  Removed....................................................33922
52.629  Removed....................................................33922
52.631  Removed....................................................33922
52.670  (c)(28) introductory text revised; eff. 7-25-95............27893
52.672  Removed....................................................33922
52.677  Removed....................................................33922
52.682  Removed....................................................33922
52.688  Removed....................................................33923
52.689  Removed....................................................33923
52.720  (c)(107) added..............................................5320
    (c)(109) added.................................................15235
    (c)(106) added.................................................16803
    (c)(108) added.................................................16806
    (c)(105) added.................................................17229
    (c)(110) added; eff. 7-3-95....................................21707
    c)(111) added..................................................36063
    (c)(112) added.................................................36065
    (c)(114) added.................................................49772
    (c)(113) added.................................................49780
    (c)(116) added.................................................54806
    (c)(115) added.................................................54806
    (c)(117) added.................................................56240
52.723  Removed....................................................33923
52.724  (h) added..................................................17001
52.726  (i) added..................................................13634
    (h) added......................................................13635
    (j) added......................................................48899
52.735  Removed....................................................33923
52.741  (z)(1)(i) amended; (z)(1)(ii) and (5) removed.................41
    (x)(7) added; (z)(4) revised...................................13045
    (e)(8), (h)(6), (u)(6), (7), (v)(6), (x)(6) and (8) through 
(13) added.........................................................14900
    (u)(8) added; (z)(1) removed...................................43387
    (e)(10) added; (z)(4) removed..................................43393
    (x)(14) added..................................................43395
52.769  Introductory text revised; (b) added.......................22241
    Added..........................................................22242
52.770  (c)(92) added..............................................12700
    (c)(95) added; eff. 7-3-95.....................................21720
    (c)(99) added; eff. 7-17-95....................................31413
    (c)(96) added..................................................34859
    (c)(97) and (98) added.........................................43012
52.772  Removed....................................................33923
52.777  (j) added....................................................377
    (h) added......................................................38722
52.783  Removed....................................................33923
52.788  Added......................................................43012
52.792  Removed....................................................33923
52.820  (c)(60) added; eff. 8-14-95................................31092
    (c)(61) added; eff. 8-22-95....................................32603
    (c)(61) removed................................................45055
    (c)(61) added..................................................55199
52.824  Removed....................................................33923
52.827  Removed....................................................33923
52.832  Removed....................................................33923
52.870  (c)(30) added..............................................36364
52.872  Added......................................................36364
52.878  Removed....................................................33923
52.880  Removed....................................................33923
52.883  Removed....................................................33923
52.920  (c)(73) added...............................................7128
    (c)(77) added..................................................21447
    (c)(78) added; eff. 7-10-95....................................27411
    (c)(79) added; eff. 7-28-95....................................31088
    (c)(71) added; eff. 8-18-95....................................31915
    (c)(80) added..................................................33752
    (c)(72) added..................................................38707
    (c)(76) added..................................................47094
    (c)(81) added..................................................49778
52.922  Removed....................................................33923
52.929  Removed....................................................33923
52.930  (c) added; eff. 8-7-95.....................................32469
    Regulation at 60 FR 32469 withdrawn............................40101
52.937  Added......................................................21717
52.970  (c)(65) added...............................................2016
      (c)(66) added................................................54308
52.975  Added......................................................43025
    Existing text redesignated as (a); (b) added...................47285

[[Page 603]]

    (c) added......................................................51360
52.979  Removed....................................................33923
52.980  Removed....................................................33923
52.992  Added.......................................................5864
52.993  Added......................................................13911

                                  1996

40 CFR
                                                                   61 FR
                                                                    Page
Chapter I
52  State implementation plan determinations....1718, 1720, 4216, 11162, 
                  17576, 19193, 20147, 33678, 36292, 49262, 51598, 54948
    Announcement...................................................56450
    Technical correction............................................7221
52.02  (d) revised.................................................16060
52.03  Removed.....................................................16061
52.16  Revised.....................................................16061
52.19  Removed.....................................................16061
52.21  (b)(23)(i) amended...........................................9918
    (l)(1) revised; (l)(2) amended.................................41894
52.50  (c)(68) added................................................5286
    (c)(69) added..................................................11138
52.70  (c)(26) added................................................5705
    (c)(25) added..................................................24715
52.74  Removed.....................................................16061
52.82  Revised; eff. 8-27-96.......................................33678
52.120  (c)(72) revised; (c)(79) and (80) added.....................3579
    (c)(77) revised; (c)(81) added..................................5286
    (c)(84) added..................................................15719
    (c)(83) and (85) added.........................................51611
52.145  (d)(3)(v), (vi) and (vii) revised..........................14975
52.150  Added......................................................56470
    Heading corrected..............................................58281
52.175  Removed....................................................16061
52.220  (c)(224)(i)(A)(1) added.....................................1718
    (c)(215)(i)(A)(4) and (C) added.................................3580
    (c)(188)(i)(A)(4), (193)(i)(C)(1), (194)(i)(F)(2), 
(207)(i)(C)(2) and (210)(i)(C)(1) added.............................4216
    (c)(216)(i)(A)(2) added; interim................................4219
    (c)(199)(i)(D), (202)(i)(C)(3), (214)(i)(D) and (222)(i)(C) 
added...............................................................4890
    (c)(194)(i)(F)(3) and (4) added.................................4892
    (c)(196)(i)(C), (210)(i)(D) and (222)(i)(D) added...............4894
    (c)(183)(i)(B)(3), (198)(i)(F)(2), (199)(i)(C), 
(207)(i)(C)(3), (214)(i)(C) and (225)(i)(B) added...................5290
    (c)(214)(i)(C)(2) and (221).....................................5517
    (c)(198)(i)(I) added............................................5704
    (c)(194)(i)(A)(4), (198)(i)(J), (210)(i)(C)(2), (215)(i)(B)(2) 
added...............................................................7709
    (c)(194)(i)(B)(2), (3) and (222)(i)(C)(2) added.................7994
    (c)(199)(i)(D)(2), (202)(i)(C)(4) and (216)(i)(A)(3) added.....15721
    (c)(227) added.................................................18501
    (c)(195)(i)(B), (202)(i)(E)(2) and (222)(i)(C)(3)..............18962
    (c)(198)(i)(E)(2), (J)(2), (207)(i)(B)(4), (C)(4), (D)(2), 
(215)(i)(B)(3), (D)(1), (216)(i)(A)(4), (220)(i)(B)(2), 
(225)(i)(B)(5) and (C)(2) added....................................18966
    (c)(194)(i)(C)(2) and (197)(i)(C) added........................19557
    (c)(196)(i)(C)(2), (215)(i)(A)(5) and (225)(i)(D) added; eff. 
7-5-96.............................................................20139
    (c)(214)(i)(D)(2), (E) and (225)(i)(B)(2) added; eff. 7-5-96 
                                                                   20147
    (c)(198)(i)(K)(2) added; eff. 7-8-96...........................20454
    (c)(185)(i)(A)(9), (194)(i)(G), (198)(i)(K), (207)(i)(B)(2) 
and (225)(i)(B)(3) added; eff. 8-12-96.............................29662
    (c)(226) and (228) added; eff. 8-23-96.........................32345
    (c)(231) added.................................................36502
    (c)(194)(i)(A)(5), (207)(i)(B)(3), (220)(i)(B)(1), 
(225)(i)(B)(4) and (C)(1) added....................................37393
    (c)(189)(i)(B)(3), (210)(i)(E), (220)(i)(B)(3), 
(221)(i)(A)(2), (229) and (230) added..............................38574
    (c)(185)(i)(A)(9), (194)(i)(G), (198)(i)(K), (207)(i)(B)(2) 
and (225)(i)(B)(3) removed.........................................43977
    (c)(187)(i)(A)(6) added........................................44163
    (c)(191)(i)(D), (196)(i)(C)(3), (229)(i)(A) and (231)(i)(B) 
added..............................................................52299
    (c)(197)(i)(A)(2) and (224)(i)(B) added........................54943
    (c)(207)(i)(D)(3), (220)(i)(C) and (230)(i)(B) added...........56472
    (c)(193)(i)(A)(3) added........................................56629
    (c)(179)(i)(E) and (193)(i)(D) added...........................56631
    (c)(232) added.................................................57780

[[Page 604]]

    (c)(239) added.................................................58134
    (c)(240) added.................................................64293
52.222  (b) added..................................................56474
    (a)(1)(iv) added...............................................56476
52.320  (c)(73) added..............................................11153
    (c)(74) added..................................................49684
    (c)(75) added..................................................51787
    (c)(63) added..................................................60615
52.347  Removed....................................................60615
52.348  Added......................................................67469
52.370  (c)(71) added..............................................38576
52.372  Removed....................................................38576
    Added..........................................................56900
52.373  Revised....................................................38576
52.374  Table revised..............................................38576
52.376  (c) added..................................................38577
52.420  (c)(54) added...............................................2422
    (c)(52) added...................................................7418
    (c)(54)(i)(B) amended..........................................13101
    Corrected......................................................24239
52.423  Added.......................................................1841
52.470  (c)(36) added...............................................2936
52.472  (e) removed.................................................2936
52.474  Added.......................................................2936
52.520  (c)(90) added...............................................3575
    (c)(92) added...................................................6545
    (c)(94) added..................................................18260
    (c)(91) added..................................................49066
    (c)(96) added..................................................65957
52.535  Removed....................................................49066
52.570  (c)(47) added...............................................3819
    (c)(44) added...................................................3821
    (c)(43) added...................................................3824
    (c)(37)(i)(A) revised; eff. 8-26-96............................33373
52.670  (c)(31) added; eff. 7-29-96................................27023
52.676  Removed....................................................16061
52.680  Removed....................................................16061
52.684  Removed....................................................16061
52.686  Removed....................................................16061
52.691  Added......................................................20732
    Existing text designated as (a); (b) added.....................66606
52.720  (c)(102) added..............................................2427
    (c)(118) added..................................................3578
    (c)(119) added..................................................5513
    (c)(124) added.................................................11142
    (c)(125) and (126) added.......................................11551
    Regulation at 61 FR 2427 withdrawn.............................12030
    (c)(121) added.................................................14486
    (c)(122) added.................................................15717
    (c)(127) added; eff. 7-8-96....................................20457
    (c)(120) added.................................................38581
    (c)(130) added.................................................38590
    (c)(128) added.................................................41341
    (c)(102) added.................................................54559
    (c)(131) added.................................................67472
52.725  (d) added..................................................41345
52.726  (k) added...................................................2437
    (l) added.......................................................5295
    (m) added......................................................38590
52.727  Removed....................................................16061
52.729  Removed....................................................16061
52.731  Removed....................................................16061
52.732  Removed....................................................16061
52.733  Removed....................................................16061
52.734  Removed....................................................16061
52.741  (a)(2) revised..............................................2428
    Regulation at 61 FR 2428 withdrawn.............................12030
      (a)(2) revised...............................................54559
52.770  (c)(100) added..............................................3582
    (c)(101) added..................................................4897
    (c)(103) added..................................................4899
    (c)(102) added.................................................11149
    (c)(104) added.................................................11556
    (c)(105) added.................................................14489
    (c)(107) added.................................................15706
    (c)(108) added; eff. 8-12-96...................................29963
    (c)(106) added; eff. 8-12-96...................................29970
    (c)(114) added.................................................55894
52.777  (i) added...................................................2437
52.795  (f) and (g) added..........................................58486
52.820  (c)(63) added..............................................18959
52.826  Removed....................................................16061
52.829  Removed....................................................16061
52.870  (c)(31) added..............................................18255
    (c)(32) added..................................................51368
52.873  (a) removed; (b) redesignated as (a).......................16061
52.879  Removed....................................................16061
52.920  (c)(82) added...............................................8875
    (c)(83) added..................................................14491
    (c)(84) added; eff. 8-27-96....................................33676
52.930  (c) added..................................................50720
52.970  (c)(70) added..............................................37839
    (c)(64) added..................................................38591
    (c)(67) added..................................................48412
    Regulation at 61 FR 37839 withdrawn............................50238
    (c)(69) added..................................................53642
    (c)(71) added..................................................54742
    (c)(72) added..................................................55896
52.972  Removed....................................................16061
52.975  (d) added..................................................37839
    Regulation at 61 FR 37839 withdrawn............................50238
52.978  Removed....................................................16061
52.988  Removed....................................................16061
52.992  (b) added...................................................2446

[[Page 605]]

    (c) added.......................................................7221
52.994  Added......................................................48412
52.995  Added; eff. 7-19-96........................................31037

                                  1997

40 CFR
                                                                   62 FR
                                                                    Page
Chapter I
52  Authority citation revised......................................8328
    Technical correction......................11769, 15751, 37724, 61016
    State implementation plan determinations........27199, 27201, 29668, 
                         32207, 43647, 45531, 52946, 54769, 61914, 64522
    Administrative change..........................................27968
    Notice.........................................................61236
52.12  (c) revised..................................................8328
52.33  Added........................................................8328
52.50  (c)(70) added; eff. 8-5-97..................................30992
52.66  Added.......................................................49158
52.76  Added........................................................6132
52.120  (c)(82) added..............................................12546
    (c)(87) added; eff. 8-11-97....................................31738
    (c)(3)(i), (18)(i)(A), (iv)(A), (38)(i)(C), (50)(ii)(C), 
(51)(i)(B) and (52)(ii)(B) added; eff. 7-28-97.....................34643
    (c)(73), (74)(i)(B), (77)(i)(A)(1) removed; (c)(74)(i)(A) 
revised; (c)(77)(i)(A)(2) redesignated as (c)(77)(i)(A)(1); 
(c)(88) added......................................................41864
    (c)(83) and (85) removed.......................................63458
52.123  (f) added..................................................41864
52.124  (b) added..................................................41864
52.220  (c)(204)(i)(A)(6), (B)(2), (C) through (F), (205)(i)(A), 
        (213) and (233) through (238) added.........................1186
    (c)(211)(i)(A)(2) and (213)(i)(A)(1)(i) added...................1190
    (c)(194)(i)(F)(5), (207)(i)(E)(1), (209), (213), 
(225)(i)(E)(1) added................................................2607
    (c)(224)(i)(C) added............................................3216
    (c)(195)(i)(B)(2), (202)(i)(C)(5), (221)(i)(A)(3), 
(230)(i)(A)(2) and (i)(C) added.....................................3223
    (c)(184)(i)(B)(6) and (207)(i)(C)(5) added......................8173
    (c)(241) added.................................................14641
    (c)(207)(i)(E), (213) and (225)(i)(E) revised..................17083
    (c)(239)(i)(D) added...........................................18712
    (c)(52)(xiii)(E), (80)(i)(D) and (207)(i)(A)(2) added..........23368
    (c)(164)(i)(E) and (168)(i)(H)(2) added; eff. 7-7-97...........24576
    Regulation at 62 FR 17083 withdrawn............................30760
    (c)(239)(i)(D) removed.........................................32688
    (c)(202)(i)(C)(6) and (241)(i)(B) added; eff. 8-18-97..........32694

[[Page 606]]

    (b)(1), (2), (3), (c)(6)(i)(B), (ii) through (xiv), 
(21)(vi)(B), (ix)(C), (xiv)(B), (24)(vi)(C), (vii)(D), (ix)(C), 
(25)(i)(E), (ii)(D), (iv)(B), (26)(iv)(C), (vii)(B), (viii)(C), 
(xvi)(D), (xvii)(B), (C), (27)(vii)(B), (28)(iv)(B), (30)(x)(B), 
(31)(i)(F), (xiii)(B), (xviii)(D), (32)(ii)(B), (iii)(E), (iv)(D), 
(E), (35)(iii)(C), (v)(B), (vi)(C), (xii)(F), (xiii)(C), (xiv)(E), 
(xv)(E), (xvi)(C), (xvii)(D), (37)(iv)(D), (v)(C), (39)(ii)(F), 
(iii)(F), (iv)(F), (vii)(C), (viii)(C), (ix)(B), (x)(B), 
(41)(ii)(D), (ix)(C), (x)(B), (C), (xii)(B), (42)(i)(E), (iii)(C), 
(xiii)(D), (xiv)(C), (44)(iv)(C), (v)(B), (45)(iii)(B), 
(50)(i)(B), (ii)(B), (iii)(B), (iv)(B), (v)(B), (51)(i)(C), 
(iii)(B), (iv)(B), (v)(B), (vi)(B), (vii)(D), (viii)(D), (E), 
(ix)(D), (xii)(C), (xiii)(B), (xv)(C), (xvi)(B), (xx)(B), 
(52)(iv)(D), (E), (ix)(C), (xi)(B), (xii)(B), (xv)(C), (xix)(C), 
(54)(iii)(B), (iv)(D), (58)(ii)(C), (74)(i)(B), (87)(vi)(B), 
(88)(i)(D), (89)(vi)(B), (92)(ii)(D), (93)(iv)(C), (95)(v)(C), 
(96)(iii)(B), (98)(i)(D), (101)(ii)(E), (103)(ii)(D), (iv)(E), 
(vi)(B), (vii)(B), (viii)(B), (ix)(B), (x)(B), (xii)(C), (xiv)(B), 
(xvii)(B), (xviii)(B), (124)(iii)(B), (v)(C), (vi)(C), (vii)(C), 
(viii)(C), (ix)(C), (x)(C), (125)(iv)(B), (vi)(B), (126)(i)(C), 
(iii)(C), (v)(C), (127) introductory text, (iii)(B), (vi)(B), 
(vii)(D), (137)(ii)(D), (iv)(C), (vii)(C), (viii)(B), (138)(v)(D), 
(140)(i)(C), (153)(ii)(C), (154)(i)(C), (iii)(C), (159)(iii)(B), 
(168)(i)(A)(3), (E)(3), (171)(i)(D)(5) and (177)(i)(D)(2) added; 
eff. 7-28-97.......................................................34644
    (c)(196)(i)(D), (202)(i)(F) and (245) added....................36216
    (c)(185)(i)(A)(9), (198)(i)(K), (207)(i)(B)(2) and 
(225)(i)(B)(3) added...............................................37138
    (c)(239)(i)(D) added...........................................41867
    (c)(197)(i)(B)(2) added........................................44909
    (c)(224)(i)(D) added...........................................44912
    Regulation at 62 FR 41867 withdrawn............................47369
    (c)(26)(ix)(B), (xvi)(E), (27)(vii)(C), (39)(viii)(D), 
(ix)(C), (x)(C) and (246) added....................................48483
    (c)(229)(i)(A)(2) added........................................48485
    (c)(224)(i)(E) added...........................................53544
    (c)(243) added.................................................54588
    (c)(224)(i)(D) removed.........................................54769
    (c)(197)(i)(D) and (241)(i)(A)(2) added........................59287
    (c)(184)(i)(B)(5) and (225)(i)(A)(2) added.....................60785
    (c)(250) added.................................................62951
    (c)(239)(i)(E) added...........................................65613
    (c)(239)(i)(E)(2) added........................................67000
    (c)(239)(i)(A)(2)..............................................67004
52.222  (a)(2) and (3) added.......................................40937
    (b)(2) added...................................................43647
52.238  Added.......................................................1187
52.241  Added.......................................................1187
52.320  (c)(79) added...............................................2310
    (c)(77) added...................................................2587
    (c)(72) added...................................................2914
    (c)(78) added...................................................4463
    (c)(80) added..................................................10700
    (c)(81) added..................................................13336
    (c)(82) added..................................................18721
    (c)(71) added..................................................67009
    (c)(76) added..................................................68195
52.324  (c) removed.................................................2914
52.329  (b) added...................................................2914
52.329  (a) revised................................................68195
52.332  (f) added..................................................18723
    (b) and (e) redesignated as (b)(1) and (e)(1); (b)(2) and 
(e)(2) added.......................................................66008
    (g) and (h) added..............................................68195
52.343  (a)(1) removed; (a)(2), (3) and (4) redesignated (a)(1), 
        (2) and (3).................................................2914
    (a)(3) revised.................................................13336
52.370  (c)(70) added..............................................14331
    (c)(72) added..................................................52020
    (c)(74) added..................................................55340
    (c)(72)(i)(B) and (ii)(K) corrected............................65224
52.372  Existing text designated as (a); (b) added.................14331
52.374  Table revised..............................................14331
52.384  Added......................................................55340
52.385  Added......................................................52022
    Table corrected................................................65224

[[Page 607]]

52.420  (c)(48) and (49) added.....................................11331
    (c)(55) added..................................................26401
    (c)(58) added..................................................37724
    Regulation at 62 FR 37722 eff. date corrected to 8-14-97.......40139
52.424  Added......................................................27199
    (b) added......................................................27197
52.470  (c)(37) added..............................................40938
52.474  Heading revised; existing text designated as (a); (b) 
        added......................................................19679
52.520  (c)(97) added...............................................2590
    (c)(98) added..................................................38919
52.570  (c)(50) added; interim.....................................42918
52.620  (b)(1) and (c)(16)(i)(B) added; (c)(10) and (14) revised; 
        eff. 7-28-97...............................................34648
52.720  (c)(132) added..............................................2918
    (c)(123) added.................................................11329
    (c)(113) added; eff. 8-8-97....................................31343
    (c)(134) added; eff. 8-18-97...................................32697
    (c)(106(i)(D) added; (c)(109) revised..........................43102
    (c)(139) added.................................................62953
    (c)(137) added.................................................67001
52.726  (n) added...................................................6127
    (o) added.......................................................6129
    (m) correctly designated.......................................23534
    (p), (q) and (r) added.........................................37506
    Regulation at 62 FR 37506 withdrawn............................46447
    (p), (q) and (r) added.........................................66294
52.729  Added......................................................16705
52.769  (a) removed................................................19056
52.770  (c)(110) added..............................................2593
    (c)(111) added..................................................2597
    (c)(113) added..................................................3220
    (c)(109) added..................................................7159
    (c)(112) added.................................................15852
    Regulation at 62 FR 7159 withdrawn.............................17096
    (c)(119) added.................................................18523
    (c)(116) added.................................................19056
    (c)(118) added; eff. 7-7-97....................................24824
    Regulation at 62 FR 15852 withdrawn............................28349
    (c)(120) added; eff. 8-4-97....................................30257
    (c)(109) added.................................................38922
52.776  (q) added..................................................45171
52.777  (k) and (l) added..........................................15852
    (m), (n) and (o) added; eff. 7-7-97............................24824
    Regulation at 62 FR 15852 withdrawn............................28349
    (p) added; eff. 8-4-97.........................................30257
    (q) added; eff. 8-25-97........................................34407
    (k) added......................................................38464
    (q) added......................................................55176
    (s) added......................................................64735
52.820  (c)(64) added..............................................55173
    (c)(65) added..................................................63455
52.870  (c)(33) added..............................................36213
52.920  (c)(85) added...............................................2916
52.930  (d) added; eff. 7-28-97....................................28637
52.970  (c)(70) added................................................652
    (c)(69)(i)(A) correctly revised.................................9081
    (c)(73) added..................................................24037
    Regulation at 62 FR 28637 withdrawn............................40281
    (e) added......................................................55176
    (d) added......................................................61246
52.970  (c)(64) introductory text and (i) revised..................51604
    (c)(68) added..................................................52951
    (c)(74) added..................................................63661
52.975  (d) added....................................................652
    (e) added......................................................24038
52.975  (f) added..................................................64286
52.992  (d) added..................................................29078
52.994  Existing text designated as (a); (b) added.................63662
52.996  Added......................................................61634

                                  1998

    (Regulations published from January 1, 1998 through July 1, 1998)

40 CFR
                                                                   63 FR
                                                                    Page
Chapter I
52  State implementation plan determinations.......26, 3650, 8573, 9423, 
                                       15094, 16435, 25167, 26720, 34298
    Technical correction............................................6483
52.12  Regulation at 62 FR 8328 eff. date corrected to 12-30-97......414
52.33  Regulation at 62 FR 8328 eff. date corrected to 12-30-97......414
52.50  (c)(71) added.................................................676
52.70  (c)(27) added...............................................11840
52.111  Added......................................................16441
52.120  (c)(83)(i)(B) added.........................................6489
    (c)(78)(i)(C), (82)(i)(C), (83) and (85) added..................6491
    (c)(89) and (90) added..........................................6659
    (c)(82)(i)(D) added............................................15305
    (c)(82)(i)(E) added............................................24435
52.123  (g) added..................................................28904
52.170  (c)(29) added..............................................17683
    (c)(29) removed................................................32981
52.181  (a) revised.........................................17683, 32981

[[Page 608]]

52.220  (c)(231)(i)(B)(2), (239)(i)(D)(1) and (244) added...........6075
    (c)(239)(i)(E)(3) added.........................................8128
    (c)(6)(i)(C), (21)(vi)(C), (121)(ii)(C), (173)(i)(E), 
(182)(i)(E), (194)(i)(E)(2), (244)(i)(B) and (245)(i)(B) added.....11833
    (c)(230)(i)(B)(2) added........................................13531
    (c)(252) and (253) added.......................................15311
    (c)(251) added.................................................19661
    (c)(247) added.................................................19662
    (c)(240)(i)(A)(2), (3) and (4) added; eff. 7-15-98.............32623
    (c)(248) and (254) added; eff. 7-22-98.........................33855
52.243  Added......................................................19662
52.320  (c)(8), (15) and (72)(i)(D) revised........................14360
    (c)(84) added..................................................15302
52.370  (c)(60) added...............................................6487
    (c)(73) added..................................................20318
52.385  Table amended........................................6487, 20318
52.420  Regulation at 62 FR 11331 eff. date corrected to 5-1-98....24114
52.424  (b) introductory text revised...............................1368
    (c) added......................................................16435
52.473  Added; eff. 7-2-98.........................................29957
52.520  (c)(87) revised; eff. 7-27-98..............................28906
52.582  Existing text designated as (a); (b) added.................23390
    (b)(5) added; eff. 8-10-98.....................................34302
52.720  (c)(135) added..............................................8858
    (c)(136) added..................................................8859
    (c)(138) added.................................................11838
    (c)(141) added.................................................11846
    (c)(142) added.................................................13787
    (c)(140) added; eff. 7-20-98...................................27492
52.725  (e) added..................................................11846
52.726  (s) added; eff. 8-31-98....................................35844
52.769  (b) removed; eff. 8-28-98..................................35144
52.770  (c)(121) added..............................................2147
    (c)(122) added; eff. 8-28-98...................................35144
    (c)(123) added; eff. 8-31-98...................................35839
52.777  (q) redesignated as (r)....................................29957
52.820  (c)(66) added...............................................5269
    (c)(67) added; eff. 8-24-98....................................34602
52.834  Added......................................................13345
52.920  (c)(86) added...............................................1929
52.930  Regulation at 62 FR 61246 eff. date corrected to 2-10-98 
                                                                    6664
    (f) added......................................................14625
52.970  (c)(75) added..............................................11374
    (c)(79) added; eff. 7-10-98....................................25775
    First (c)(55) removed..........................................35537
52.992  Regulation at 62 FR 29078 eff. date corrected to 5-1-98....24115
52.994  Regulation at 62 FR 61634 eff. date corrected to 2-13-98 
                                                                    7290
    Removed........................................................11374
52.996  Correctly designated........................................4397