[Congressional Bills 115th Congress]
[From the U.S. Government Publishing Office]
[H.R. 3458 Introduced in House (IH)]

<DOC>






115th CONGRESS
  1st Session
                                H. R. 3458

  To require certain semiautomatic pistols manufactured, imported, or 
   sold by Federal firearms licensees to be capable of microstamping 
ammunition, and to prohibit the removal, obliteration, or alteration of 
    the microstamped code or microstamping capability of a firearm.


_______________________________________________________________________


                    IN THE HOUSE OF REPRESENTATIVES

                             July 27, 2017

  Mr. Brown of Maryland (for himself, Mr. Brady of Pennsylvania, Mr. 
Cicilline, Mr. Connolly, Mr. Gutierrez, Mr. Larson of Connecticut, Mr. 
  McEachin, Ms. Norton, Mr. Raskin, Ms. Schakowsky, Mr. Serrano, Mr. 
   Suozzi, and Mr. Vargas) introduced the following bill; which was 
               referred to the Committee on the Judiciary

_______________________________________________________________________

                                 A BILL


 
  To require certain semiautomatic pistols manufactured, imported, or 
   sold by Federal firearms licensees to be capable of microstamping 
ammunition, and to prohibit the removal, obliteration, or alteration of 
    the microstamped code or microstamping capability of a firearm.

    Be it enacted by the Senate and House of Representatives of the 
United States of America in Congress assembled,

SECTION 1. SHORT TITLE.

    This Act may be cited as the ``Make Identifiable Criminal Rounds 
Obvious Act'' or the ``MICRO Act''.

SEC. 2. REQUIREMENT THAT CERTAIN SEMIAUTOMATIC PISTOLS MANUFACTURED, 
              IMPORTED, OR SOLD BY FEDERAL FIREARMS LICENSEES BE 
              CAPABLE OF MICROSTAMPING AMMUNITION.

    Section 923 of title 18, United States Code, is amended by adding 
at the end the following:
    ``(m)(1)(A) A person licensed under this chapter shall not 
manufacture, import, or transfer a semiautomatic pistol to which this 
subparagraph applies that is not capable of microstamping ammunition.
    ``(B) For purposes of subparagraph (A), a pistol is capable of 
microstamping ammunition if--
            ``(i) a microscopic array of characters that identify the 
        make, model, and serial number of the pistol is etched into the 
        breech face and firing pin of the pistol; and
            ``(ii) when ammunition is fired from the pistol, the 
        characters are copied from the breech face and firing pin onto 
        the cartridge case of the ammunition.
    ``(C) Subparagraph (A) shall apply only to semiautomatic pistols 
which--
            ``(i) are manufactured, or imported into the United States, 
        on or after the effective date of this subsection; and
            ``(ii) have not been transferred to a person not licensed 
        under this chapter.
    ``(2) Whoever violates paragraph (1) shall be fined an amount equal 
to--
            ``(A) in the case of a first such violation by the 
        violator, $1,000 multiplied by the number of semiautomatic 
        pistols involved in the violation;
            ``(B) in the case of a second such violation by the 
        violator, $2,000 multiplied by the number of semiautomatic 
        pistols involved in the violation; or
            ``(C) in the case of a third such violation by the 
        violator, $3,000 multiplied by the number of semiautomatic 
        pistols involved in the violation.''.

SEC. 3. PROHIBITION ON THE REMOVAL, OBLITERATION, OR ALTERATION OF THE 
              MICROSTAMPED CODE OR MICROSTAMPING CAPABILITY OF A 
              FIREARM.

    (a) In General.--Section 922 of title 18, United States Code, is 
amended by inserting after subsection (t) the following:
    ``(v)(1) It shall be unlawful for any person to remove, obliterate, 
or alter the microstamped code or microstamping capability of a firearm 
that has been shipped or transported in interstate or foreign commerce.
    ``(2) Paragraph (1) shall not apply to the replacement of a firing 
pin that is damaged or worn, and is in need of replacement.''.
    (b) Penalties.--Section 924 of such title is amended by adding at 
the end the following:
    ``(q)(1)(A) In the case of a knowing violation of section 922(v), 
the Attorney General may, after notice and opportunity for hearing--
            ``(i) subject the violator to a civil penalty in an amount 
        equal to not more than $5,000; and
            ``(ii) if the violator is a licensed manufacturer, licensed 
        importer, or licensed dealer, suspend for not more than 6 
        months, or revoke, any license issued to the licensee under 
        this chapter.
    ``(B) An action under subparagraph (A) may be reviewed only as 
provided under section 923(f).
    ``(2) The suspension or revocation of a license or the imposition 
of a civil penalty under paragraph (1) shall not preclude any 
administrative remedy that is otherwise available to the Attorney 
General.''.

SEC. 4. EFFECTIVE DATE.

    The amendments made by this Act shall take effect on the date that 
is 2 years after the date of the enactment of this Act.
                                 <all>