[Congressional Bills 111th Congress]
[From the U.S. Government Publishing Office]
[S. 3925 Introduced in Senate (IS)]

111th CONGRESS
  2d Session
                                S. 3925

 To amend the Energy Policy and Conservation Act to improve the energy-
  efficiency of, and standards applicable to, certain appliances and 
                   equipment, and for other purposes.


_______________________________________________________________________


                   IN THE SENATE OF THE UNITED STATES

                           September 29, 2010

 Mr. Bingaman (for himself and Ms. Klobuchar) introduced the following 
bill; which was read twice and referred to the Committee on Energy and 
                           Natural Resources

_______________________________________________________________________

                                 A BILL


 
 To amend the Energy Policy and Conservation Act to improve the energy-
  efficiency of, and standards applicable to, certain appliances and 
                   equipment, and for other purposes.

    Be it enacted by the Senate and House of Representatives of the 
United States of America in Congress assembled,

SECTION 1. SHORT TITLE; TABLE OF CONTENTS.

    (a) Short Title.--This Act may be cited as the ``Implementation of 
National Consensus Appliance Agreements Act''.
    (b) Table of Contents.--The table of contents of this Act is as 
follows:

Sec. 1. Short title; table of contents.
Sec. 2. Energy conservation standards.
Sec. 3. Energy conservation standards for heat pump pool heaters.
Sec. 4. Portable light fixtures.
Sec. 5. GU-24 base lamps.
Sec. 6. Efficiency standards for bottle-type water dispensers, 
                            commercial hot food holding cabinets, and 
                            portable electric spas.
Sec. 7. Test procedure petition process.
Sec. 8. Energy efficiency provisions.
Sec. 9. Measuring icemaker energy.
Sec. 10. Credit for Energy Star smart appliances.
Sec. 11. Video game console energy efficiency study.
Sec. 12. Refrigerator and freezer standards.
Sec. 13. Room air conditioner standards.
Sec. 14. Uniform efficiency descriptor for covered water heaters.
Sec. 15. Clothes dryers.
Sec. 16. Standards for clothes washers.
Sec. 17. Dishwashers.
Sec. 18. Standards for certain incandescent reflector lamps and 
                            reflector lamps.
Sec. 19. Petition for amended standards.
Sec. 20. Efficiency standards for class A external power supplies.
Sec. 21. Prohibited acts.
Sec. 22. Outdoor lighting.
Sec. 23. Standards for commercial furnaces.
Sec. 24. Service over the counter, self-contained, medium temperature 
                            commercial refrigerators.
Sec. 25. Motor market assessment and commercial awareness program.
Sec. 26. Study of compliance with energy standards for appliances.
Sec. 27. Study of direct current electricity supply in certain 
                            buildings.
Sec. 28. Technical corrections.

SEC. 2. ENERGY CONSERVATION STANDARDS.

    (a) Definition of Energy Conservation Standard.--Section 321 of the 
Energy Policy and Conservation Act (42 U.S.C. 6291) is amended--
            (1) by striking paragraph (6) and inserting the following:
            ``(6) Energy conservation standard.--
                    ``(A) In general.--The term `energy conservation 
                standard' means 1 or more performance standards that--
                            ``(i) for covered products (excluding 
                        clothes washers, dishwashers, showerheads, 
                        faucets, water closets, and urinals), prescribe 
                        a minimum level of energy efficiency or a 
                        maximum quantity of energy use, determined in 
                        accordance with test procedures prescribed 
                        under section 323;
                            ``(ii) for showerheads, faucets, water 
                        closets, and urinals, prescribe a minimum level 
                        of water efficiency or a maximum quantity of 
                        water use, determined in accordance with test 
                        procedures prescribed under section 323; and
                            ``(iii) for clothes washers and 
                        dishwashers--
                                    ``(I) prescribe a minimum level of 
                                energy efficiency or a maximum quantity 
                                of energy use, determined in accordance 
                                with test procedures prescribed under 
                                section 323; and
                                    ``(II) include a minimum level of 
                                water efficiency or a maximum quantity 
                                of water use, determined in accordance 
                                with those test procedures.
                    ``(B) Inclusions.--The term `energy conservation 
                standard' includes--
                            ``(i) 1 or more design requirements, if the 
                        requirements were established--
                                    ``(I) on or before the date of 
                                enactment of this subclause;
                                    ``(II) as part of a direct final 
                                rule under section 325(p)(4); or
                                    ``(III) as part of a final rule 
                                published on or after January 1, 2012; 
                                and
                            ``(ii) any other requirements that the 
                        Secretary may prescribe under section 325(r).
                    ``(C) Exclusion.--The term `energy conservation 
                standard' does not include a performance standard for a 
                component of a finished covered product, unless 
                regulation of the component is specifically authorized 
                or established pursuant to this title.''; and
            (2) by adding at the end the following:
            ``(67) EER.--The term `EER' means energy efficiency ratio.
            ``(68) HSPF.--The term `HSPF' means heating seasonal 
        performance factor.''.
    (b) EER and HSPF Test Procedures.--Section 323(b) of the Energy 
Policy and Conservation Act (42 U.S.C. 6293(b)) is amended by adding at 
the end the following:
            ``(19) EER and hspf test procedures.--
                    ``(A) In general.--Subject to subparagraph (B), for 
                purposes of residential central air conditioner and 
                heat pump standards that take effect on or before 
                January 1, 2015--
                            ``(i) the EER shall be tested at an outdoor 
                        test temperature of 95 degrees Fahrenheit; and
                            ``(ii) the HSPF shall be calculated based 
                        on Region IV conditions.
                    ``(B) Revisions.--The Secretary may revise the EER 
                outdoor test temperature and the conditions for HSPF 
                calculations as part of any rulemaking to revise the 
                central air conditioner and heat pump test method.''.
    (c) Central Air Conditioners and Heat Pumps.--Section 325(d) of the 
Energy Policy and Conservation Act (42 U.S.C. 6295(d)) is amended by 
adding at the end the following:
            ``(4) Central air conditioners and heat pumps (except 
        through-the-wall central air conditioners, through-the-wall 
        central air conditioning heat pumps, and small duct, high 
        velocity systems) manufactured on or after january 1, 2015.--
                    ``(A) Base national standards.--
                            ``(i) Seasonal energy efficiency ratio.--
                        The seasonal energy efficiency ratio of central 
                        air conditioners and central air conditioning 
                        heat pumps manufactured on or after January 1, 
                        2015, shall not be less than the following:
                                    ``(I) Split Systems: 13 for central 
                                air conditioners and 14 for heat pumps.
                                    ``(II) Single Package Systems: 14.
                            ``(ii) Heating seasonal performance 
                        factor.--The heating seasonal performance 
                        factor of central air conditioning heat pumps 
                        manufactured on or after January 1, 2015, shall 
                        not be less than the following:
                                    ``(I) Split Systems: 8.2.
                                    ``(II) Single Package Systems: 8.0.
                    ``(B) Regional standards.--
                            ``(i) Seasonal energy efficiency ratio.--
                        The seasonal energy efficiency ratio of central 
                        air conditioners and central air conditioning 
                        heat pumps manufactured on or after January 1, 
                        2015, and installed in States having historical 
                        average annual, population weighted, heating 
                        degree days less than 5,000 (specifically the 
                        States of Alabama, Arizona, Arkansas, 
                        California, Delaware, Florida, Georgia, Hawaii, 
                        Kentucky, Louisiana, Maryland, Mississippi, 
                        Nevada, New Mexico, North Carolina, Oklahoma, 
                        South Carolina, Tennessee, Texas, and Virginia) 
                        or in the District of Columbia, the 
                        Commonwealth of Puerto Rico, or any other 
                        territory or possession of the United States 
                        shall not be less than the following:
                                    ``(I) Split Systems: 14 for central 
                                air conditioners and 14 for heat pumps.
                                    ``(II) Single Package Systems: 14.
                            ``(ii) Energy efficiency ratio.--The energy 
                        efficiency ratio of central air conditioners 
                        (not including heat pumps) manufactured on or 
                        after January 1, 2015, and installed in the 
                        State of Arizona, California, New Mexico, or 
                        Nevada shall be not less than the following:
                                    ``(I) Split Systems: 12.2 for split 
                                systems having a rated cooling capacity 
                                less than 45,000 BTU per hour and 11.7 
                                for products having a rated cooling 
                                capacity equal to or greater than 
                                45,000 BTU per hour.
                                    ``(II) Single Package Systems: 
                                11.0.
                            ``(iii) Application of subsection (o)(6).--
                        Subsection (o)(6) shall apply to the regional 
                        standards set forth in this subparagraph.
                    ``(C) Amendment of standards.--
                            ``(i) In general.--Not later than January 
                        1, 2017, the Secretary shall publish a final 
                        rule to determine whether the standards in 
                        effect for central air conditioners and central 
                        air conditioning heat pumps should be amended.
                            ``(ii) Application.--The rule shall provide 
                        that any amendments shall apply to products 
                        manufactured on or after January 1, 2022.
                    ``(D) Consideration of additional performance 
                standards or efficiency criteria.--
                            ``(i) Forum.--Not later than 4 years in 
                        advance of the expected publication date of a 
                        final rule for central air conditioners and 
                        heat pumps under subparagraph (C), the 
                        Secretary shall convene and facilitate a forum 
                        for interested persons that are fairly 
                        representative of relevant points of view 
                        (including representatives of manufacturers of 
                        the covered product, States, and efficiency 
                        advocates), as determined by the Secretary, to 
                        consider adding additional performance 
                        standards or efficiency criteria in the 
                        forthcoming rule.
                            ``(ii) Recommendation.--If, within 1 year 
                        of the initial convening of such a forum, the 
                        Secretary receives a recommendation submitted 
                        jointly by such representative interested 
                        persons to add 1 or more performance standards 
                        or efficiency criteria, the Secretary shall 
                        incorporate the performance standards or 
                        efficiency criteria in the rulemaking process, 
                        and, if justified under the criteria 
                        established in this section, incorporate such 
                        performance standards or efficiency criteria in 
                        the revised standard.
                            ``(iii) No recommendation.--If no such 
                        joint recommendation is made within 1 year of 
                        the initial convening of such a forum, the 
                        Secretary may add additional performance 
                        standards or efficiency criteria if the 
                        Secretary finds that the benefits substantially 
                        exceed the burdens of the action.
                    ``(E) New construction levels.--
                            ``(i) In general.--As part of any final 
                        rule concerning central air conditioner and 
                        heat pump standards published after June 1, 
                        2013, the Secretary shall determine if the 
                        building code levels specified in section 
                        327(f)(3)(C) should be amended subject to 
                        meeting the criteria of subsection (o) when 
                        applied specifically to new construction.
                            ``(ii) Effective date.--Any amended levels 
                        shall not take effect before January 1, 2018.
                            ``(iii) Amended levels.--The final rule 
                        shall contain the amended levels, if any.''.
    (d) Through-the-Wall Central Air Conditioners, Through-the-Wall 
Central Air Conditioning Heat Pumps, and Small Duct, High Velocity 
Systems.--Section 325(d) of the Energy Policy and Conservation Act (42 
U.S.C. 6295(d)) (as amended by subsection (c)) is amended by adding at 
the end the following:
            ``(5) Standards for through-the-wall central air 
        conditioners, through-the-wall central air conditioning heat 
        pumps, and small duct, high velocity systems.--
                    ``(A) Definitions.--In this paragraph:
                            ``(i) Small duct, high velocity system.--
                        The term `small duct, high velocity system' 
                        means a heating and cooling product that 
                        contains a blower and indoor coil combination 
                        that--
                                    ``(I) is designed for, and 
                                produces, at least 1.2 inches of 
                                external static pressure when operated 
                                at the certified air volume rate of 
                                220-350 CFM per rated ton of cooling; 
                                and
                                    ``(II) when applied in the field, 
                                uses high velocity room outlets 
                                generally greater than 1,000 fpm that 
                                have less than 6.0 square inches of 
                                free area.
                            ``(ii) Through-the-wall central air 
                        conditioner; through-the-wall central air 
                        conditioning heat pump.--The terms `through-
                        the-wall central air conditioner' and `through-
                        the-wall central air conditioning heat pump' 
                        mean a central air conditioner or heat pump, 
                        respectively, that is designed to be installed 
                        totally or partially within a fixed-size 
                        opening in an exterior wall, and--
                                    ``(I) is not weatherized;
                                    ``(II) is clearly and permanently 
                                marked for installation only through an 
                                exterior wall;
                                    ``(III) has a rated cooling 
                                capacity no greater than 30,000 Btu/hr;
                                    ``(IV) exchanges all of its outdoor 
                                air across a single surface of the 
                                equipment cabinet; and
                                    ``(V) has a combined outdoor air 
                                exchange area of less than 800 square 
                                inches (split systems) or less than 
                                1,210 square inches (single packaged 
                                systems) as measured on the surface 
                                area described in subclause (IV).
                            ``(iii) Revision.--The Secretary may revise 
                        the definitions contained in this subparagraph 
                        through publication of a final rule.
                    ``(B) Rulemaking.--
                            ``(i) In general.--Not later than June 30, 
                        2011, the Secretary shall publish a final rule 
                        to determine whether standards for through-the-
                        wall central air conditioners, through-the-wall 
                        central air conditioning heat pumps and small 
                        duct, high velocity systems should be 
                        established or amended.
                            ``(ii) Application.--The rule shall provide 
                        that any new or amended standard shall apply to 
                        products manufactured on or after June 30, 
                        2016.''.
    (e) Furnaces.--Section 325(f) of the Energy Policy and Conservation 
Act (42 U.S.C. 6295(f)) is amended by adding at the end the following:
            ``(5) Non-weatherized furnaces (including mobile home 
        furnaces, but not including boilers) manufactured on or after 
        may 1, 2013, and weatherized furnaces manufactured on or after 
        january 1, 2015.--
                    ``(A) Base national standards.--
                            ``(i)  Non-weatherized furnaces.--The 
                        annual fuel utilization efficiency of non-
                        weatherized furnaces manufactured on or after 
                        May 1, 2013, shall be not less than the 
                        following:
                                    ``(I) Gas furnaces, 80 percent.
                                    ``(II) Oil furnaces, 83 percent.
                            ``(ii) Weatherized furnaces.--The annual 
                        fuel utilization efficiency of weatherized gas 
                        furnaces manufactured on or after January 1, 
                        2015, shall be not less than 81 percent.
                    ``(B) Regional standard.--
                            ``(i) Annual fuel utilization efficiency.--
                        The Secretary shall by May 1, 2011, establish a 
                        standard for the annual fuel utilization 
                        efficiency of non-weatherized gas furnaces 
                        manufactured on or after May 1, 2013, and 
                        installed in States having historical average 
                        annual, population weighted, heating degree 
                        days equal to or greater than 5,000 
                        (specifically the States of Alaska, Colorado, 
                        Connecticut, Idaho, Illinois, Indiana, Iowa, 
                        Kansas, Maine, Massachusetts, Michigan, 
                        Minnesota, Missouri, Montana, Nebraska, New 
                        Hampshire, New Jersey, New York, North Dakota, 
                        Ohio, Oregon, Pennsylvania, Rhode Island, South 
                        Dakota, Utah, Vermont, Washington, West 
                        Virginia, Wisconsin, and Wyoming).
                            ``(ii) Application of subsection (o)(6).--
                        Subsection (o)(6) shall apply to the regional 
                        standard set forth in this subparagraph.
                            ``(iii) Separate standards.--The Secretary 
                        may establish separate standards for furnaces 
                        to be installed in newly constructed buildings 
                        and for replacement in existing buildings.
                    ``(C) Amendment of standards.--
                            ``(i) Non-weatherized furnaces.--
                                    ``(I) In general.--Not later than 
                                January 1, 2014, the Secretary shall 
                                publish a final rule to determine 
                                whether the standards in effect for 
                                non-weatherized furnaces should be 
                                amended.
                                    ``(II) Application.--The rule shall 
                                provide that any amendments shall apply 
                                to products manufactured on or after 
                                January 1, 2019.
                            ``(ii) Weatherized furnaces.--
                                    ``(I) In general.--Not later than 
                                January 1, 2017, the Secretary shall 
                                publish a final rule to determine 
                                whether the standard in effect for 
                                weatherized furnaces should be amended.
                                    ``(II) Application.--The rule shall 
                                provide that any amendments shall apply 
                                to products manufactured on or after 
                                January 1, 2022.
                    ``(D) New construction levels.--
                            ``(i) In general.--As part of any final 
                        rule concerning furnace standards published 
                        after June 1, 2013, the Secretary shall 
                        determine if the building code levels specified 
                        in section 327(f)(3)(C) should be amended 
                        subject to meeting the criteria of subsection 
                        (o) when applied specifically to new 
                        construction.
                            ``(ii) Effective date.--Any amended levels 
                        shall not take effect before January 1, 2018.
                            ``(iii) Amended levels.--The final rule 
                        shall contain the amended levels, if any.''.
    (f) Exception for Certain Building Code Requirements.--Section 
327(f) of the Energy Policy and Conservation Act (42 U.S.C. 6297(f)) is 
amended--
            (1) in paragraph (3), by striking subparagraphs (B) through 
        (F) and inserting the following:
                    ``(B) The code does not contain a mandatory 
                requirement that, under all code compliance paths, 
                requires that the covered product have an energy 
                efficiency exceeding 1 of the following levels:
                            ``(i) The applicable energy conservation 
                        standard established in or prescribed under 
                        section 325.
                            ``(ii) The level required by a regulation 
                        of the State for which the Secretary has issued 
                        a rule granting a waiver under subsection (d).
                    ``(C) If the energy consumption or conservation 
                objective in the code is determined using covered 
                products, including any baseline building designs 
                against which all submitted building designs are to be 
                evaluated, the objective is based on the use of covered 
                products having efficiencies not exceeding--
                            ``(i) for residential furnaces, central air 
                        conditioners, and heat pumps, effective not 
                        earlier than January 1, 2013, and until such 
                        time as a level takes effect for the product 
                        under clause (ii)--
                                    ``(I) for the States described in 
                                section 325(f)(5)(B)(i)--
                                            ``(aa) 92 percent AFUE for 
                                        gas furnaces; and
                                            ``(bb) 14 SEER for central 
                                        air conditioners (not including 
                                        heat pumps);
                                    ``(II) for the States and other 
                                localities described in section 
                                325(d)(4)(B)(i) (except for the States 
                                of Arizona, California, Nevada, and New 
                                Mexico)--
                                            ``(aa) 90 percent AFUE for 
                                        gas furnaces; and
                                            ``(bb) 15 SEER for central 
                                        air conditioners;
                                    ``(III) for the States of Arizona, 
                                California, Nevada, and New Mexico--
                                            ``(aa) 92 percent AFUE for 
                                        gas furnaces;
                                            ``(bb) 15 SEER for central 
                                        air conditioners;
                                            ``(cc) an EER of 12.5 for 
                                        air conditioners (not including 
                                        heat pumps) with cooling 
                                        capacity less than 45,000 Btu 
                                        per hour; and
                                            ``(dd) an EER of 12.0 for 
                                        air conditioners (not including 
                                        heat pumps) with cooling 
                                        capacity of 45,000 Btu per hour 
                                        or more; and
                                    ``(IV) for all States--
                                            ``(aa) 85 percent AFUE for 
                                        oil furnaces; and
                                            ``(bb) 15 SEER and 8.5 HSPF 
                                        for heat pumps;
                            ``(ii) the building code levels established 
                        pursuant to section 325; or
                            ``(iii) the applicable standards or levels 
                        specified in subparagraph (B).
                    ``(D) The credit to the energy consumption or 
                conservation objective allowed by the code for 
                installing a covered product having an energy 
                efficiency exceeding the applicable standard or level 
                specified in subparagraph (C) is on a 1-for-1 
                equivalent energy use or equivalent energy cost basis, 
                which may take into account the typical lifetimes of 
                the products and building features, using lifetimes for 
                covered products based on information published by the 
                Department of Energy or the American Society of 
                Heating, Refrigerating and Air-Conditioning Engineers.
                    ``(E) If the code sets forth 1 or more combinations 
                of items that meet the energy consumption or 
                conservation objective, and if 1 or more combinations 
                specify an efficiency level for a covered product that 
                exceeds the applicable standards and levels specified 
                in subparagraph (B)--
                            ``(i) there is at least 1 combination that 
                        includes such covered products having 
                        efficiencies not exceeding 1 of the standards 
                        or levels specified in subparagraph (B); and
                            ``(ii) if 1 or more combinations of items 
                        specify an efficiency level for a furnace, 
                        central air conditioner, or heat pump that 
                        exceeds the applicable standards and levels 
                        specified in subparagraph (B), there is at 
                        least 1 combination that the State has found to 
                        be reasonably achievable using commercially 
                        available technologies that includes such 
                        products having efficiencies at the applicable 
                        levels specified in subparagraph (C), except 
                        that no combination need include a product 
                        having an efficiency less than the level 
                        specified in subparagraph (B)(ii).
                    ``(F) The energy consumption or conservation 
                objective is specified in terms of an estimated total 
                consumption of energy (which may be specified in units 
                of energy or its equivalent cost).'';
            (2) in paragraph (4)(B)--
                    (A) by inserting after ``building code'' the first 
                place it appears the following: ``contains a mandatory 
                requirement that, under all code compliance paths,''; 
                and
                    (B) by striking ``unless the'' and all that follows 
                through ``subsection (d)''; and
            (3) by adding at the end the following:
            ``(5) Replacement of covered product.--Paragraph (3) shall 
        not apply to the replacement of a covered product serving an 
        existing building unless the replacement results in an increase 
        in capacity greater than--
                    ``(A) 12,000 Btu per hour for residential air 
                conditioners and heat pumps; or
                    ``(B) 20 percent for other covered products.''.

SEC. 3. ENERGY CONSERVATION STANDARDS FOR HEAT PUMP POOL HEATERS.

    (a) Definitions.--
            (1) Efficiency descriptor.--Section 321(22) of the Energy 
        Policy and Conservation Act (42 U.S.C. 6291(22)) is amended--
                    (A) in subparagraph (E), by inserting ``gas-fired'' 
                before ``pool heaters''; and
                    (B) by adding at the end the following:
                    ``(F) For heat pump pool heaters, coefficient of 
                performance of heat pump pool heaters.''.
            (2) Coefficient of performance of heat pump pool heaters.--
        Section 321 of the Energy Policy and Conservation Act (42 
        U.S.C. 6291) is amended by inserting after paragraph (25) the 
        following:
            ``(25A) Coefficient of performance of heat pump pool 
        heaters.--The term `coefficient of performance of heat pump 
        pool heaters' means the ratio of the capacity to power input 
        value obtained at the following rating conditions: 50.0 F db/
        44.2 F wb outdoor air and 80.0 F entering water temperatures, 
        according to AHRI Standard 1160.''.
            (3) Thermal efficiency of gas-fired pool heaters.--Section 
        321(26) of the Energy Policy and Conservation Act (42 U.S.C. 
        6291(26)) is amended by inserting ``gas-fired'' before ``pool 
        heaters''.
    (b) Standards for Pool Heaters.--Section 325(e)(2) of the Energy 
Policy and Conservation Act (42 U.S.C. 6295(e)(2)) is amended--
            (1) by striking ``(2) The thermal efficiency of pool 
        heaters'' and inserting the following:
            ``(2) Pool heaters.--
                    ``(A) Gas-fired pool heaters.--The thermal 
                efficiency of gas-fired pool heaters''; and
            (2) by adding at the end the following:
                    ``(B) Heat pump pool heaters.--Heat pump pool 
                heaters manufactured on or after the date of enactment 
                of this subparagraph shall have a minimum coefficient 
                of performance of 4.0.''.

SEC. 4. PORTABLE LIGHT FIXTURES.

    (a) Definitions.--Section 321 of the Energy Policy and Conservation 
Act (42 U.S.C. 6291) (as amended by section 2(a)(2)) is amended by 
adding at the end the following:
            ``(69) Art work light fixture.--The term `art work light 
        fixture' means a light fixture designed only to be mounted 
        directly to an art work and for the purpose of illuminating 
        that art work.
            ``(70) LED light engine.--The term `LED light engine' or 
        `LED light engine with integral heat sink' means a subsystem of 
        an LED light fixture that--
                    ``(A) includes 1 or more LED components, 
                including--
                            ``(i) an LED driver power source with 
                        electrical and mechanical interfaces; and
                            ``(ii) an integral heat sink to provide 
                        thermal dissipation; and
                    ``(B) may be designed to accept additional 
                components that provide aesthetic, optical, and 
                environmental control.
            ``(71) LED light fixture.--The term `LED light fixture' 
        means a complete lighting unit consisting of--
                    ``(A) an LED light source with 1 or more LED lamps 
                or LED light engines; and
                    ``(B) parts--
                            ``(i) to distribute the light;
                            ``(ii) to position and protect the light 
                        source; and
                            ``(iii) to connect the light source to 
                        electrical power.
            ``(72) Light fixture.--The term `light fixture' means a 
        product designed to provide light that includes--
                    ``(A) at least 1 lamp socket; and
                    ``(B) parts--
                            ``(i) to distribute the light;
                            ``(ii) position and protect 1 or more 
                        lamps; and
                            ``(iii) to connect 1 or more lamps to a 
                        power supply.
            ``(73) Portable light fixture.--
                    ``(A) In general.--The term `portable light 
                fixture' means a light fixture that has a flexible cord 
                and an attachment plug for connection to a nominal 120-
                volt circuit that--
                            ``(i) allows the user to relocate the 
                        product without any rewiring; and
                            ``(ii) typically can be controlled with a 
                        switch located on the product or the power cord 
                        of the product.
                    ``(B) Exclusions.--The term `portable light 
                fixture' does not include--
                            ``(i) direct plug-in night lights, sun or 
                        heat lamps, medical or dental lights, portable 
                        electric hand lamps, signs or commercial 
                        advertising displays, photographic lamps, 
                        germicidal lamps, or light fixtures for marine 
                        use or for use in hazardous locations (as those 
                        terms are defined in ANSI/NFPA 70 of the 
                        National Electrical Code); or
                            ``(ii) decorative lighting strings, 
                        decorative lighting outfits, or electric 
                        candles or candelabra without lamp shades that 
                        are covered by Underwriter Laboratories (UL) 
                        standard 588, `Seasonal and Holiday Decorative 
                        Products'.''.
    (b) Coverage.--Section 322(a) of the Energy Policy and Conservation 
Act (42 U.S.C. 6292(a)) is amended--
            (1) by redesignating paragraph (20) as paragraph (21); and
            (2) by inserting after paragraph (19) the following:
            ``(20) Portable light fixtures.''.
    (c) Test Procedures.--Section 323(b) of the Energy Policy and 
Conservation Act (42 U.S.C. 6293(b)) (as amended by section 2(b)) is 
amended by adding at the end the following:
            ``(20) LED fixtures and led light engines.--Test procedures 
        for LED fixtures and LED light engines shall be based on 
        Illuminating Engineering Society of North America test 
        procedure LM-79, Approved Method for Electrical and Photometric 
        Testing of Solid-State Lighting Devices and an IES-approved 
        test procedure for testing LED light engines.''.
    (d) Standards.--Section 325 of the Energy Policy and Conservation 
Act (42 U.S.C. 6295) is amended--
            (1) by redesignating subsection (ii) as subsection (kk); 
        and
            (2) by inserting after subsection (hh) the following:
    ``(ii) Portable Light Fixtures.--
            ``(1) In general.--Subject to paragraphs (2) and (3), 
        portable light fixtures manufactured on or after January 1, 
        2012, shall meet 1 or more of the following requirements:
                    ``(A) Be a fluorescent light fixture that meets the 
                requirements of the Energy Star Program for Residential 
                Light Fixtures, Version 4.2.
                    ``(B) Be equipped with only 1 or more GU-24 line-
                voltage sockets, not be rated for use with incandescent 
                lamps of any type (as defined in ANSI standards), and 
                meet the requirements of version 4.2 of the Energy Star 
                program for residential light fixtures.
                    ``(C) Be an LED light fixture or a light fixture 
                with an LED light engine and comply with the following 
                minimum requirements:
                            ``(i) Minimum light output: 200 lumens 
                        (initial).
                            ``(ii) Minimum LED light engine efficacy: 
                        40 lumens/watt installed in fixtures that meet 
                        the minimum light fixture efficacy of 29 
                        lumens/watt or, alternatively, a minimum LED 
                        light engine efficacy of 60 lumens/watt for 
                        fixtures that do not meet the minimum light 
                        fixture efficacy of 29 lumens/watt.
                            ``(iii) All portable fixtures shall have a 
                        minimum LED light fixture efficacy of 29 
                        lumens/watt and a minimum LED light engine 
                        efficacy of 60 lumens/watt by January 1, 2016.
                            ``(iv) Color Correlated Temperature (CCT): 
                        2700K through 4000K.
                            ``(v) Minimum Color Rendering Index (CRI): 
                        75.
                            ``(vi) Power factor equal to or greater 
                        than 0.70.
                            ``(vii) Portable luminaries that have 
                        internal power supplies shall have zero standby 
                        power when the luminaire is turned off.
                            ``(viii) LED light sources shall deliver at 
                        least 70 percent of initial lumens for at least 
                        25,000 hours.
                    ``(D)(i) Be equipped with an ANSI-designated E12, 
                E17, or E26 screw-based socket and be prepackaged and 
                sold together with 1 screw-based compact fluorescent 
                lamp or screw-based LED lamp for each screw-based 
                socket on the portable light fixture.
                    ``(ii) The compact fluorescent or LED lamps 
                prepackaged with the light fixture shall be fully 
                compatible with any light fixture controls incorporated 
                into the light fixture (for example, light fixtures 
                with dimmers shall be packed with dimmable lamps).
                    ``(iii) Compact fluorescent lamps prepackaged with 
                light fixtures shall meet the requirements of the 
                Energy Star Program for CFLs Version 4.0.
                    ``(iv) Screw-based LED lamps shall comply with the 
                minimum requirements described in subparagraph (C).
                    ``(E) Be equipped with 1 or more single-ended, non-
                screw based halogen lamp sockets (line or low voltage), 
                a dimmer control or high-low control, and be rated for 
                a maximum of 100 watts.
            ``(2) Review.--
                    ``(A) Review.--The Secretary shall review the 
                criteria and standards established under paragraph (1) 
                to determine if revised standards are technologically 
                feasible and economically justified.
                    ``(B) Components.--The review shall include 
                consideration of--
                            ``(i) whether a separate compliance 
                        procedure is still needed for halogen fixtures 
                        described in subparagraph (E) and, if 
                        necessary, what an appropriate standard for 
                        halogen fixtures shall be;
                            ``(ii) which of the specific technical 
                        criteria described in subparagraphs (A), (C), 
                        and (D)(iii) should be modified; and
                            ``(iii) which fixtures should be exempted 
                        from the light fixture efficacy standard as of 
                        January 1, 2016, because the fixtures are 
                        primarily decorative in nature (as defined by 
                        the Secretary) and, even if exempted, are 
                        likely to be sold in limited quantities.
                    ``(C) Timing.--
                            ``(i) Determination.--Not later than 
                        January 1, 2014, the Secretary shall publish 
                        amended standards, or a determination that no 
                        amended standards are justified, under this 
                        subsection.
                            ``(ii) Standards.--Any standards under this 
                        subsection take effect on January 1, 2016.
            ``(3) Art work light fixtures.--Art work light fixtures 
        manufactured on or after January 1, 2012, shall--
                    ``(A) comply with paragraph (1); or
                    ``(B)(i) contain only ANSI-designated E12 screw-
                based line-voltage sockets;
                    ``(ii) have not more than 3 sockets;
                    ``(iii) be controlled with an integral high/low 
                switch;
                    ``(iv) be rated for not more than 25 watts if 
                fitted with 1 socket; and
                    ``(v) be rated for not more than 15 watts per 
                socket if fitted with 2 or 3 sockets.
            ``(4) Exception from preemption.--Notwithstanding section 
        327, Federal preemption shall not apply to a regulation 
        concerning portable light fixtures adopted by the California 
        Energy Commission on or before January 1, 2014.''.

SEC. 5. GU-24 BASE LAMPS.

    (a) Definitions.--Section 321 of the Energy Policy and Conservation 
Act (42 U.S.C. 6291) (as amended by section 4(a)) is amended by adding 
at the end the following:
            ``(74) GU-24.--The term `GU-24''' means the designation of 
        a lamp socket, based on a coding system by the International 
        Electrotechnical Commission, under which--
                    ``(A) `G' indicates a holder and socket type with 2 
                or more projecting contacts, such as pins or posts;
                    ``(B) `U' distinguishes between lamp and holder 
                designs of similar type that are not interchangeable 
                due to electrical or mechanical requirements; and
                    ``(C) 24 indicates the distance in millimeters 
                between the electrical contact posts.
            ``(75) GU-24 adaptor.--
                    ``(A) In general.--The term `GU-24 Adaptor' means a 
                1-piece device, pig-tail, wiring harness, or other such 
                socket or base attachment that--
                            ``(i) connects to a GU-24 socket on 1 end 
                        and provides a different type of socket or 
                        connection on the other end; and
                            ``(ii) does not alter the voltage.
                    ``(B) Exclusion.--The term `GU-24 Adaptor' does not 
                include a fluorescent ballast with a GU-24 base.
            ``(76) GU-24 base lamp.--`GU-24 base lamp' means a light 
        bulb designed to fit in a GU-24 socket.''.
    (b) Standards.--Section 325 of the Energy Policy and Conservation 
Act (42 U.S.C. 6295) (as amended by section 4(d)) is amended by 
inserting after subsection (ii) the following:
    ``(jj) GU-24 Base Lamps.--
            ``(1) In general.--A GU-24 base lamp shall not be an 
        incandescent lamp as defined by ANSI.
            ``(2) GU-24 adaptors.--GU-24 adaptors shall not adapt a GU-
        24 socket to any other line voltage socket.''.

SEC. 6. EFFICIENCY STANDARDS FOR BOTTLE-TYPE WATER DISPENSERS, 
              COMMERCIAL HOT FOOD HOLDING CABINETS, AND PORTABLE 
              ELECTRIC SPAS.

    (a) Definitions.--Section 321 of the Energy Policy and Conservation 
Act (42 U.S.C. 6291) (as amended by section 5(a)) is amended by adding 
at the end the following:
            ``(77) Bottle-type water dispenser.--The term `bottle-type 
        water dispenser' means a drinking water dispenser that is--
                    ``(A) designed for dispensing hot and cold water; 
                and
                    ``(B) uses a removable bottle or container as the 
                source of potable water.
            ``(78) Commercial hot food holding cabinet.--
                    ``(A) In general.--The term `commercial hot food 
                holding cabinet' means a heated, fully-enclosed 
                compartment that--
                            ``(i) is designed to maintain the 
                        temperature of hot food that has been cooked in 
                        a separate appliance;
                            ``(ii) has 1 or more solid or glass doors; 
                        and
                            ``(iii) has an interior volume of 8 cubic 
                        feet or more.
                    ``(B) Exclusions.--The term `commercial hot food 
                holding cabinet' does not include--
                            ``(i) a heated glass merchandising cabinet;
                            ``(ii) a drawer warmer;
                            ``(iii) a cook-and-hold appliance; or
                            ``(iv) a mobile serving cart with both hot 
                        and cold compartments.
            ``(79) Compartment bottle-type water dispenser.--The term 
        `compartment bottle-type water dispenser' means a drinking 
        water dispenser that--
                    ``(A) is designed for dispensing hot and cold 
                water;
                    ``(B) uses a removable bottle or container as the 
                source of potable water; and
                    ``(C) includes a refrigerated compartment with or 
                without provisions for making ice.
            ``(80) Portable electric spa.--
                    ``(A) In general.--The term `portable electric spa' 
                means a factory-built electric spa or hot tub that--
                            ``(i) is intended for the immersion of 
                        persons in heated water circulated in a closed 
                        system; and
                            ``(ii) is not intended to be drained and 
                        filled with each use.
                    ``(B) Inclusions.--The term `portable electric spa' 
                includes--
                            ``(i) a filter;
                            ``(ii) a heater (including an electric, 
                        solar, or gas heater);
                            ``(iii) a pump;
                            ``(iv) a control; and
                            ``(v) other equipment, such as a light, a 
                        blower, and water sanitizing equipment.
                    ``(C) Exclusions.--The term `portable electric spa' 
                does not include--
                            ``(i) a permanently installed spa that, 
                        once installed, cannot be moved; or
                            ``(ii) a spa that is specifically designed 
                        and exclusively marketed for medical treatment 
                        or physical therapy purposes.
            ``(81) Water dispenser.--The term `water dispenser' means a 
        factory-made assembly that--
                    ``(A) mechanically cools and heats potable water; 
                and
                    ``(B) dispenses the cooled or heated water by 
                integral or remote means.''.
    (b) Coverage.--
            (1) In general.--Section 322(a) of the Energy Policy and 
        Conservation Act (42 U.S.C. 6292(a)) (as amended by section 
        4(b)(1)) is amended--
                    (A) by redesignating paragraph (21) as paragraph 
                (24); and
                    (B) by inserting after paragraph (20) the 
                following:
            ``(21) Bottle-type water dispensers and compartment bottle-
        type water dispensers.
            ``(22) Commercial hot food holding cabinets.
            ``(23) Portable electric spas.''.
            (2) Conforming amendments.--
                    (A) Section 324 of the Energy Policy and 
                Conservation Act (42 U.S.C. 6294) is amended by 
                striking ``(19)'' each place it appears in subsections 
                (a)(3), (b)(1)(B), (b)(3), and (b)(5) and inserting 
                ``(24)''.
                    (B) Section 325(l) of the Energy Policy and 
                Conservation Act (42 U.S.C. 6295(l)) is amended by 
                striking ``paragraph (19)'' each place it appears in 
                paragraphs (1) and (2) and inserting ``paragraph 
                (24)''.
    (c) Test Procedures.--Section 323(b) of the Energy Policy and 
Conservation Act (42 U.S.C. 6293(b)) (as amended by section 4(c)) is 
amended by adding at the end the following:
            ``(21) Bottle-type water dispensers.--
                    ``(A) In general.--Test procedures for bottle-type 
                water dispensers and compartment bottle-type water 
                dispensers shall be based on the document `Energy Star 
                Program Requirements for Bottled Water Coolers version 
                1.1' published by the Environmental Protection Agency.
                    ``(B) Integral, automatic timers.--A unit with an 
                integral, automatic timer shall not be tested under 
                this paragraph using section 4D of the test criteria 
                (relating to Timer Usage).
            ``(22) Commercial hot food holding cabinets.--
                    ``(A) In general.--Test procedures for commercial 
                hot food holding cabinets shall be based on the test 
                procedures described in ANSI/ASTM F2140-01 (Test for 
                idle energy rate-dry test).
                    ``(B) Interior volume.--Interior volume shall be 
                based under this paragraph on the method demonstrated 
                in the document `Energy Star Program Requirements for 
                Commercial Hot Food Holding Cabinets' of the 
                Environmental Protection Agency, as in effect on August 
                15, 2003.
            ``(23) Portable electric spas.--
                    ``(A) In general.--Test procedures for portable 
                electric spas shall be based on the test method for 
                portable electric spas described in section 1604 of 
                title 20, California Code of Regulations, as amended on 
                December 3, 2008.
                    ``(B) Normalized consumption.--Consumption shall be 
                normalized under this paragraph for a water temperature 
                difference of 37 degrees Fahrenheit.
                    ``(C) ANSI test procedure.--If the American 
                National Standards Institute publishes a test procedure 
                for portable electric spas, the Secretary shall revise 
                the procedure established under this paragraph, as 
                determined appropriate by the Secretary.''.
    (d) Standards.--Section 325 of the Energy Policy and Conservation 
Act (42 U.S.C. 6295) (as amended by sections 4(d) and 5(b)) is 
amended--
            (1) by redesignating subsection (kk) as subsection (oo); 
        and
            (2) by inserting after subsection (jj) the following:
    ``(kk) Bottle-Type Water Dispensers.--Effective beginning January 
1, 2012--
            ``(1) a bottle-type water dispenser shall not have standby 
        energy consumption that is greater than 1.2 kilowatt-hours per 
        day; and
            ``(2) a compartment bottle-type water dispenser shall not 
        have standby energy consumption that is greater than 1.3 
        kilowatt-hours per day.
    ``(ll) Commercial Hot Food Holding Cabinets.--Effective beginning 
January 1, 2012, a commercial hot food holding cabinet shall have a 
maximum idle energy rate of 40 watts per cubic foot of interior volume.
    ``(mm) Portable Electric Spas.--Effective beginning January 1, 
2012, a portable electric spa shall not have a normalized standby power 
rate of greater than 5 (V<SUP>2/3</SUP>) Watts (in which `V' equals the 
fill volume (in gallons)).
    ``(nn) Revisions.--
            ``(1) In general.--Not later than January 1, 2013, the 
        Secretary shall--
                    ``(A) consider in accordance with subsection (o) 
                revisions to the standards established under 
                subsections (kk), (ll), and (mm); and
                    ``(B)(i) publish a final rule establishing the 
                revised standards; or
                    ``(ii) make a finding that no revisions are 
                technically feasible and economically justified.
            ``(2) Effective date.--Any revised standards under this 
        subsection take effect on January 1, 2016.''.
    (e) Preemption.--Section 327 of the Energy Policy and Conservation 
Act (42 U.S.C. 6297) is amended--
            (1) in subsection (b)--
                    (A) in paragraph (6), by striking ``or'' after the 
                semicolon at the end;
                    (B) in paragraph (7), by striking the period at the 
                end and inserting ``; or''; and
                    (C) by adding at the end the following:
            ``(8) is a regulation that--
                    ``(A) establishes efficiency standards for bottle-
                type water dispensers, compartment bottle-type water 
                dispensers, commercial hot food holding cabinets, or 
                portable electric spas; and
                    ``(B) is in effect on or before the date of 
                enactment of this paragraph.''; and
            (2) in subsection (c)--
                    (A) in paragraph (8)(B), by striking ``and'' after 
                the semicolon at the end;
                    (B) in paragraph (9)--
                            (i) by striking ``except that--'' and all 
                        that follows through ``if the Secretary'' and 
                        inserting ``except that if the Secretary'';
                            (ii) by redesignating clauses (i) and (ii) 
                        as subparagraphs (A) and (B), respectively, and 
                        indenting appropriately; and
                            (iii) in subparagraph (B) (as so 
                        redesignated), by striking the period at the 
                        end and inserting ``; or''; and
                    (C) by adding at the end the following:
            ``(10) is a regulation that--
                    ``(A) establishes efficiency standards for bottle-
                type water dispensers, compartment bottle-type water 
                dispensers, commercial hot food holding cabinets, or 
                portable electric spas; and
                    ``(B) is adopted by the California Energy 
                Commission on or before January 1, 2013.''.

SEC. 7. TEST PROCEDURE PETITION PROCESS.

    (a) Consumer Products Other Than Automobiles.--Section 323(b)(1) of 
the Energy Policy and Conservation Act (42 U.S.C. 6293(b)(1)) is 
amended--
            (1) in subparagraph (A)(i), by striking ``amend'' and 
        inserting ``publish in the Federal Register amended''; and
            (2) by adding at the end the following:
                    ``(B) Petitions.--
                            ``(i) In general.--In the case of any 
                        covered product, any person may petition the 
                        Secretary to conduct a rulemaking--
                                    ``(I) to prescribe a test procedure 
                                for the covered product; or
                                    ``(II) to amend the test procedures 
                                applicable to the covered product to 
                                more accurately or fully comply with 
                                paragraph (3).
                            ``(ii) Determination.--The Secretary 
                        shall--
                                    ``(I) not later than 90 days after 
                                the date of receipt of the petition, 
                                publish the petition in the Federal 
                                Register; and
                                    ``(II) not later than 180 days 
                                after the date of receipt of the 
                                petition, grant or deny the petition.
                            ``(iii) Basis.--The Secretary shall grant a 
                        petition if the Secretary finds that the 
                        petition contains evidence that, assuming no 
                        other evidence was considered, provides an 
                        adequate basis for determining that an amended 
                        test method would more accurately or fully 
                        comply with paragraph (3).
                            ``(iv) Effect on other requirements.--The 
                        granting of a petition by the Secretary under 
                        this subparagraph shall create no presumption 
                        with respect to the determination of the 
                        Secretary that the proposed test procedure 
                        meets the requirements of paragraph (3).
                            ``(v) Rulemaking.--
                                    ``(I) In general.--Except as 
                                provided in subclause (II), not later 
                                than the end of the 18-month period 
                                beginning on the date of granting a 
                                petition, the Secretary shall publish 
                                an amended test method or a 
                                determination not to amend the test 
                                method.
                                    ``(II) Extension.--The Secretary 
                                may extend the period described in 
                                subclause (I) for 1 additional year.
                                    ``(III) Direct final rule.--The 
                                Secretary may adopt a consensus test 
                                procedure in accordance with the direct 
                                final rule procedure established under 
                                section 325(p)(4).''.
    (b) Certain Industrial Equipment.--Section 343 of the Energy Policy 
and Conservation Act (42 U.S.C. 6314) is amended--
            (1) in subsection (a), by striking paragraph (1) and 
        inserting the following:
            ``(1) Amendment and petition process.--
                    ``(A) In general.--At least once every 7 years, the 
                Secretary shall review test procedures for all covered 
                equipment and--
                            ``(i) publish in the Federal Register 
                        amended test procedures with respect to any 
                        covered equipment, if the Secretary determines 
                        that amended test procedures would more 
                        accurately or fully comply with paragraphs (2) 
                        and (3); or
                            ``(ii) publish notice in the Federal 
                        Register of any determination not to amend a 
                        test procedure.
                    ``(B) Petitions.--
                            ``(i) In general.--In the case of any class 
                        or category of covered equipment, any person 
                        may petition the Secretary to conduct a 
                        rulemaking--
                                    ``(I) to prescribe a test procedure 
                                for the covered equipment; or
                                    ``(II) to amend the test procedures 
                                applicable to the covered equipment to 
                                more accurately or fully comply with 
                                paragraphs (2) and (3).
                            ``(ii) Determination.--The Secretary 
                        shall--
                                    ``(I) not later than 90 days after 
                                the date of receipt of the petition, 
                                publish the petition in the Federal 
                                Register; and
                                    ``(II) not later than 180 days 
                                after the date of receipt of the 
                                petition, grant or deny the petition.
                            ``(iii) Basis.--The Secretary shall grant a 
                        petition if the Secretary finds that the 
                        petition contains evidence that, assuming no 
                        other evidence was considered, provides an 
                        adequate basis for determining that an amended 
                        test method would more accurately promote 
                        energy or water use efficiency.
                            ``(iv) Effect on other requirements.--The 
                        granting of a petition by the Secretary under 
                        this paragraph shall create no presumption with 
                        respect to the determination of the Secretary 
                        that the proposed test procedure meets the 
                        requirements of paragraphs (2) and (3).
                            ``(v) Rulemaking.--
                                    ``(I) In general.--Except as 
                                provided in subclause (II), not later 
                                than the end of the 18-month period 
                                beginning on the date of granting a 
                                petition, the Secretary shall publish 
                                an amended test method or a 
                                determination not to amend the test 
                                method.
                                    ``(II) Extension.--The Secretary 
                                may extend the period described in 
                                subclause (I) for 1 additional year.
                                    ``(III) Direct final rule.--The 
                                Secretary may adopt a consensus test 
                                procedure in accordance with the direct 
                                final rule procedure established under 
                                section 325(p).'';
            (2) by striking subsection (c); and
            (3) by redesignating subsections (d) and (e) as subsections 
        (c) and (d), respectively.

SEC. 8. ENERGY EFFICIENCY PROVISIONS.

    (a) Direct Final Rule.--Section 323(b)(1) of the Energy Policy and 
Conservation Act (42 U.S.C. 6293(b)(1)) (as amended by section 7(a)(2)) 
is amended by adding at the end the following:
                    ``(C) Test procedures.--The Secretary may, in 
                accordance with the requirements of this subsection, 
                prescribe test procedures for any consumer product 
                classified as a covered product under section 322(b).
                    ``(D) New or amended test procedures.--The 
                Secretary shall direct the National Institute of 
                Standards and Technology to assist in developing new or 
                amended test procedures.''.
    (b) Criteria for Prescribing New or Amended Standards.--Section 
325(o) of the Energy Policy and Conservation Act (42 U.S.C. 6295(o)) is 
amended--
            (1) in paragraph (2)(B)--
                    (A) in clause (i)--
                            (i) in subclause (III), by adding before 
                        the semicolon ``and the estimated impact on 
                        average energy prices'';
                            (ii) in subclause (VI), by striking ``; 
                        and'' and inserting a semicolon;
                            (iii) by redesignating subclause (VII) as 
                        subclause (VIII); and
                            (iv) by inserting after subclause (VI) the 
                        following:
                                    ``(VII) the net energy, 
                                environmental, and economic impacts due 
                                to smart grid technologies or 
                                capabilities in a covered product that 
                                enable demand response or response to 
                                time-dependent energy pricing, taking 
                                into consideration the rate of use of 
                                the smart grid technologies or 
                                capabilities over the life of the 
                                product that is likely to result from 
                                the imposition of the standard; and''; 
                                and
                    (B) in clause (iii)--
                            (i) by striking ``(iii) If the Secretary 
                        finds'' and inserting the following:
                            ``(iii) Rebuttable presumption.--
                                    ``(I) In general.--Subject to 
                                subclause (II), if the Secretary 
                                finds'';
                            (ii) in subclause (I) (as designated by 
                        clause (i)), by striking ``three'' and 
                        inserting ``4''; and
                            (iii) by striking the second sentence and 
                        inserting the following:
                                    ``(II) Multiplier for certain 
                                products.--For any product with an 
                                average expected useful life of less 
                                than 4 years, the rebuttable 
                                presumption described in subclause (I) 
                                shall be determined using 75 percent of 
                                the average expected useful life of the 
                                product as a multiplier instead of 4.
                                    ``(III) Requirement for rebuttal of 
                                presumption.--A presumption described 
                                in subclause (I) may be rebutted only 
                                if the Secretary finds, based on clear 
                                and substantial evidence, that--
                                            ``(aa) the standard level 
                                        would cause substantial 
                                        hardship to the average 
                                        consumer of the product, or to 
                                        manufacturers supplying a 
                                        significant portion of the 
                                        market for the product, in 
                                        terms of manufacturing or 
                                        product cost or loss of product 
                                        utility or features, the 
                                        aggregate of which outweighs 
                                        the benefits of the standard 
                                        level;
                                            ``(bb) the standard and 
                                        implementing regulations cannot 
                                        reasonably be designed to avoid 
                                        or mitigate any hardship 
                                        described in item (aa) 
                                        (including through the adoption 
                                        of regional standards for the 
                                        products identified in, and 
                                        consistent with, paragraph (6) 
                                        or other reasonable means 
                                        consistent with this part) and 
                                        the hardship cannot be avoided 
                                        or mitigated through the 
                                        procedures described in section 
                                        504 of the Department of Energy 
                                        Organization Act (42 U.S.C. 
                                        7194); and
                                            ``(cc) the same or a 
                                        substantially similar hardship 
                                        with respect to a hardship 
                                        described in item (aa) would 
                                        not occur under a standard 
                                        adopted in the absence of the 
                                        presumption, but that otherwise 
                                        meets the requirements of this 
                                        section.
                                    ``(IV) Prohibited factors for 
                                determination.--
                                            ``(aa) In general.--Except 
                                        as provided in item (bb), a 
                                        determination by the Secretary 
                                        that the criteria triggering a 
                                        presumption described in 
                                        subclause (I) are not met, or 
                                        that the criterion for 
                                        rebutting the presumption are 
                                        met, shall not be taken into 
                                        consideration by the Secretary 
                                        in determining whether a 
                                        standard is economically 
                                        justified.
                                            ``(bb) Exception.--Evidence 
                                        presented regarding the 
                                        presumption may be considered 
                                        by the Secretary in making a 
                                        determination described in item 
                                        (aa).''; and
            (2) by adding at the end the following:
            ``(7) Incorporation of smart grid technologies.--
                    ``(A) In general.--The Secretary, after 
                consultation with the Director of the National 
                Institute of Standards and Technology, may incorporate 
                smart grid technologies or capabilities into standards 
                described in subparagraph (B).
                    ``(B) Standards.--Standards referred to in 
                subparagraph (A) shall meet the requirements of this 
                section, including through incorporation of--
                            ``(i) standards that provide credit for 
                        smart grid technologies or capabilities, if the 
                        smart grid technologies or capabilities provide 
                        net benefits substantially equivalent to 
                        benefits of products that meet the standards 
                        without smart grid technologies or 
                        capabilities, taking into consideration energy, 
                        economic, and environmental impacts (including 
                        emissions reductions from electrical 
                        generation); and
                            ``(ii) 1 or more performance standards or 
                        design requirements, if the required smart grid 
                        technologies or capabilities are 
                        technologically feasible and provide net 
                        benefits, taking into consideration energy, 
                        economic, and environmental impacts (including 
                        emissions reductions from electrical 
                        generation).''.
    (c) Obtainment of Appliance Information From Manufacturers.--
Section 326 of the Energy Policy and Conservation Act (42 U.S.C. 6296) 
is amended by striking subsection (d) and inserting the following:
    ``(d) Information Requirements.--
            ``(1) In general.--For purposes of carrying out this part, 
        the Secretary shall promulgate proposed regulations not later 
        than 1 year after the date of enactment of the Implementation 
        of National Consensus Appliance Agreements Act, and after 
        receiving public comment, final regulations not later than 18 
        months after the date of enactment of that Act, under this part 
        or other provision of law administered by the Secretary, that 
        shall require each manufacturer of a covered product, on a 
        product specific basis, to submit information or reports to the 
        Secretary--
                    ``(A) in such form as the Secretary may adopt; and
                    ``(B)(i) on an annual basis; or
                    ``(ii) at longer-than-annual intervals, but not 
                less frequently than once every 3 years.
            ``(2) Form and content of reports.--The form and content of 
        each report required by a manufacturer of a covered product 
        under paragraph (1)--
                    ``(A) may vary by product type, as determined by 
                the Secretary; and
                    ``(B) shall include information or data regarding--
                            ``(i) the annual shipments by the 
                        manufacturer of each class or category of 
                        covered products, subdivided, to the extent 
                        practicable, by--
                                    ``(I) energy efficiency, energy 
                                use, and, in the case of products with 
                                water use standards, water use;
                                    ``(II) the presence or absence of 
                                such efficiency related or energy 
                                consuming operational characteristics 
                                or components that are or may be 
                                required as part of a standard as the 
                                Secretary determines to be relevant for 
                                the purposes of carrying out this part; 
                                and
                                    ``(III) for covered products for 
                                which the Secretary may adopt regional 
                                standards, shipments to California and 
                                regional location of sale; and
                            ``(ii) such other categories of information 
                        that the Secretary determines to be relevant to 
                        carry out this part, including such other 
                        information that may be necessary--
                                    ``(I) to establish and revise--
                                            ``(aa) test procedures;
                                            ``(bb) labeling rules; and
                                            ``(cc) energy conservation 
                                        standards;
                                    ``(II) to ensure compliance with 
                                the requirements of this part; and
                                    ``(III) to estimate the impacts on 
                                consumers and manufacturers of energy 
                                conservation standards in effect as of 
                                the reporting date.
            ``(3) Requirements of secretary in promulgating 
        regulations.--
                    ``(A) In general.--In promulgating regulations 
                under paragraph (1), the Secretary shall consider--
                            ``(i) existing public sources of 
                        information, including nationally recognized 
                        certification or verification programs of trade 
                        associations and States; and
                            ``(ii)(I) whether some or all of the 
                        information described in paragraph (2) is 
                        submitted to another Federal agency; and
                            ``(II) the means by which to minimize any 
                        duplication of requests for information by 
                        Federal agencies.
                    ``(B) Coordination with trade associations and 
                states.--In carrying out subparagraph (A)(i), the 
                Secretary shall, to the extent practicable, coordinate 
                with trade associations and States--
                            ``(i) to ensure the uniformity of the 
                        reporting requirements; and
                            ``(ii) to mitigate reporting burdens.
            ``(4) Minimization of burdens on manufacturers.--In 
        carrying out this subsection, the Secretary shall exercise the 
        authority of the Secretary under this subsection in a manner 
        designed to minimize burdens on the manufacturers of covered 
        products.
            ``(5) Reporting of energy information.--
                    ``(A) In general.--Section 11(d) of the Energy 
                Supply and Environmental Coordination Act of 1974 (15 
                U.S.C. 796(d)) shall apply with respect to information 
                obtained under this subsection to the same extent and 
                in the same manner as section 11(d) of that Act applies 
                with respect to energy information obtained under 
                section 11 of that Act.
                    ``(B) Disclosure of industry aggregated shipment 
                data.--To protect individual company shipment 
                information from public disclosure, the Secretary 
                shall, to the maximum extent practicable, disclose to 
                the public the information required under clauses (i) 
                and (ii) of paragraph (2)(B) in a form that has been 
                aggregated by industry associations that are authorized 
                by manufacturers to report the aggregated information 
                for public disclosure on behalf of the manufacturers.
            ``(6) Limitations.--Nothing in this subsection limits--
                    ``(A) the ability of any State to collect 
                information and data from manufacturers, industry or 
                trade associations, or other entities, pursuant to the 
                statutory or regulatory authority of the State;
                    ``(B) the application of section 327(a) to any 
                State law (including regulations); or
                    ``(C) the authority of the Secretary to require 
                each manufacturer of a covered product to submit 
                information or reports regarding the compliance by the 
                manufacturer with the requirements of this part.
            ``(7) Periodic revisions.--In accordance with each 
        procedure and criteria required under paragraph (1), the 
        Secretary may periodically revise the reporting requirements 
        adopted under this subsection.''.
    (d) Waiver of Federal Preemption.--Section 327(d)(1) of the Energy 
Policy and Conservation Act (42 U.S.C. 6297(d)(1)) is amended--
            (1) in subparagraph (B)--
                    (A) by inserting ``(i)'' before ``Subject to 
                paragraphs''; and
                    (B) by adding at the end the following:
    ``(ii) In making a finding under clause (i), the Secretary may not 
reject a petition for failure of the petitioning State or river basin 
commission to produce confidential information maintained by any 
manufacturer or distributor, or group or association of manufacturers 
or distributors, that the petitioning party has requested and not 
received.''; and
            (2) in the matter following subparagraph (C)(ii), by adding 
        at the end the following: ``Notwithstanding the preceding 
        sentence, the Secretary may approve a waiver petition submitted 
        by a State that does not have an energy plan and forecast if 
        the waiver petition concerns a State regulation adopted 
        pursuant to a notice and comment rulemaking proceeding.''.
    (e) Permitting States To Seek Injunctive Enforcement.--Section 334 
of the Energy Policy and Conservation Act (42 U.S.C. 6304) is amended 
to read as follows:

``SEC. 334. PERMITTING STATES TO SEEK INJUNCTIVE ENFORCEMENT.

    ``(a) Jurisdiction.--The United States district courts shall have 
original jurisdiction of a civil action seeking an injunction to 
restrain--
            ``(1) any violation of section 332; and
            ``(2) any person from distributing in commerce any covered 
        product that does not comply with an applicable rule under 
        section 324 or 325.
    ``(b) Authority.--
            ``(1) In general.--Except as provided in paragraph (2), an 
        action under subsection (a) shall be brought by--
                    ``(A) the Commission; or
                    ``(B) the attorney general of a State in the name 
                of the State.
            ``(2) Exceptions.--
                    ``(A) In general.--Notwithstanding paragraph (1), 
                only the Secretary may bring an action under this 
                section to restrain--
                            ``(i) a violation of section 332(a)(3) 
                        relating to a requirement prescribed by the 
                        Secretary;
                            ``(ii) a violation of section 332(a)(4) 
                        relating to a request by the Secretary under 
                        section 326(b)(2); or
                            ``(iii) a violation of paragraph (8), (9), 
                        or (10) of section 332(a).
                    ``(B) Other prohibited acts.--An action under this 
                section regarding a violation of paragraph (5) or (7) 
                of section 332(a) shall be brought by--
                            ``(i) the Secretary; or
                            ``(ii) the attorney general of a State in 
                        the name of the State.
    ``(c) Limitation.--If an action under this section is brought by 
the attorney general of a State--
            ``(1) not less than 30 days before the date of commencement 
        of the action, the State shall--
                    ``(A) provide written notice to the Secretary and 
                the Commission; and
                    ``(B) provide the Secretary and the Commission with 
                a copy of the complaint;
            ``(2) the Secretary and the Commission--
                    ``(A) may intervene in the suit or action;
                    ``(B) upon intervening, shall be heard on all 
                matters arising from the suit or action; and
                    ``(C) may file petitions for appeal;
            ``(3) no separate action may be brought under this section 
        if, at the time written notice is provided under paragraph (1), 
        the same alleged violation or failure to comply is the subject 
        of a pending action, or a final judicial judgment or decree, by 
        the United States under this Act; and
            ``(4) the action shall not be construed--
                    ``(A) as to prevent the attorney general of a 
                State, or other authorized officer of the State, from 
                exercising the powers conferred on the attorney 
                general, or other authorized officer of the State, by 
                the laws of the State (including regulations); or
                    ``(B) as to prohibit the attorney general of a 
                State, or other authorized officer of the State, from 
                proceeding in a Federal or State court on the basis of 
                an alleged violation of any civil or criminal statute 
                of the State.
    ``(d) Venue; Service of Process.--
            ``(1) Venue.--An action under this section may be brought 
        in the United States district court for--
                    ``(A) the district in which the act, omission, or 
                transaction constituting the applicable violation 
                occurred; or
                    ``(B) the district in which the defendant--
                            ``(i) resides; or
                            ``(ii) transacts business.
            ``(2) Service of process.--In an action under this section, 
        process may be served on a defendant in any district in which 
        the defendant resides or is otherwise located.''.
    (f) Treatment of Appliances Within Building Codes.--Section 327 of 
the Energy Policy and Conservation Act (42 U.S.C. 6297) is amended by 
adding at the end the following:
    ``(h) Recognition of Alternative Refrigerant Uses.--With respect to 
State or local laws (including regulations) prohibiting, limiting, or 
restricting the use of alternative refrigerants for specific end uses 
approved by the Administrator of the Environmental Protection Agency 
pursuant to the Significant New Alternatives Program under section 612 
of the Clean Air Act (42 U.S.C. 7671k) for use in a covered product 
under section 322(a)(1) considered on or after the date of enactment of 
this subsection, notice shall be provided to the Administrator before 
or during any State or local public comment period to provide to the 
Administrator an opportunity to comment.''.
    (g) Enforcement.--Section 333 of the Energy Policy and Conservation 
Act (42 U.S.C. 6303) is amended--
            (1) in subsection (a)--
                    (A) by striking the first sentence and inserting 
                the following:
            ``(1) Prohibited acts.--Except as provided in subsection 
        (c), any person who knowingly violates any provision of section 
        332, or any regulation promulgated pursuant to that section, 
        shall be subject to a civil penalty.'';
                    (B) in the second sentence--
                            (i) by striking ``Such penalties'' and 
                        inserting the following:
            ``(2) Assessment.--The penalties''; and
                            (ii) by striking ``violations of section 
                        332(a)(5)'' and inserting ``violations of 
                        paragraphs (5), (8), (9), and (10) of section 
                        332(a)'';
                    (C) in the third sentence, by striking ``Civil 
                penalties'' and inserting the following:
            ``(3) Compromise.--Civil penalties''; and
                    (D) by striking the fourth sentence and inserting 
                the following:
            ``(4) Separate violations.--Each violation of paragraph 
        (1), (2), or (5) of section 332(a) shall constitute a separate 
        violation with respect to each covered product, with a maximum 
        civil penalty of up to $100,000 or $400 per unit, whichever is 
        greater, and each day of violation of paragraph (3), (4), (8), 
        (9), or (10) of section 332(a) shall constitute a separate 
        violation, with a maximum civil penalty of $500 per day.''; and
            (2) in subsection (d)--
                    (A) in paragraph (1), by striking the second 
                sentence; and
                    (B) in paragraph (2)(A), by striking ``Unless an 
                election is made within 30 calendar days after receipt 
                of notice under paragraph (1) to have paragraph (3) 
                apply with respect to such penalty,'' and inserting 
                ``If the proposed penalty arises from an alleged 
                violation of paragraph (3), (4), (5), (9), or (10) of 
                section 332(a),'';
            (3) by striking paragraph (3) and inserting the following:
            ``(3) Failure to certify.--If the proposed penalty arises 
        from an alleged failure to certify a covered product as 
        required by section 332(a)(8), the Secretary shall assess the 
        penalty, by order, after an informal adjudication conducted 
        under section 555 of title 5, United States Code.''; and
            (4) in paragraph (4), in the first sentence, by striking 
        ``amount of such penalty'' and inserting ``amount of the 
        penalty, plus interest assessed from the date upon which the 
        assessment of a civil penalty became a final and unappealable 
        order under paragraph (2),''.

SEC. 9. MEASURING ICEMAKER ENERGY.

    Section 323(b) of the Energy Policy and Conservation Act (42 U.S.C. 
6293(b)) (as amended by section 6(c)) is amended by adding at the end 
the following:
            ``(24) Refrigerator and freezer test procedure.--
                    ``(A) In general.--Not later than January 1, 2011, 
                the Secretary shall finalize the test procedure 
                proposed on May 27, 2010, with such modifications as 
                the Secretary determines to be appropriate and 
                consistent with this part.
                    ``(B) Rulemaking.--
                            ``(i) Initiation.--Not later than January 
                        1, 2012, the Secretary shall initiate a 
                        rulemaking to amend the test procedure 
                        described in subparagraph (A) only to 
                        incorporate measured automatic icemaker energy 
                        use.
                            ``(ii) Final rule.--Not later than December 
                        31, 2012, the Secretary shall publish a final 
                        rule regarding the matter described in clause 
                        (i).
            ``(25) Additional home appliance test procedures.--
                    ``(A) Final rule.--Not later than October 1, 2011, 
                the Secretary shall publish a final rule amending the 
                residential clothes washer test procedure.
                    ``(B) Finalization of test procedure for clothes 
                dryers.--Not later than April 1, 2011, the Secretary 
                shall finalize the test procedure for clothes dryers 
                proposed on June 29, 2010, with such modifications as 
                the Secretary determines to be appropriate and 
                consistent with this part.
                    ``(C) Finalization of test procedure for room air 
                conditioners.--Not later than April 1, 2011, the 
                Secretary shall finalize the test procedure for room 
                air conditioners proposed on June 29, 2010, with such 
                modifications as the Secretary determines to be 
                appropriate and consistent with this part.''.

SEC. 10. CREDIT FOR ENERGY STAR SMART APPLIANCES.

    Section 324A of the Energy Policy and Conservation Act (42 U.S.C. 
6294a) is amended by adding at the end the following:
    ``(e) Credit for Smart Appliances.--Not later than 180 days after 
the date of enactment of this subsection, after soliciting comments 
pursuant to subsection (c)(5), the Administrator of the Environmental 
Protection Agency, in cooperation with the Secretary, shall determine 
whether to update the Energy Star criteria for residential 
refrigerators, refrigerator-freezers, freezers, dishwashers, clothes 
washers, clothes dryers, and room air conditioners to incorporate smart 
grid and demand response features.''.

SEC. 11. VIDEO GAME CONSOLE ENERGY EFFICIENCY STUDY.

    (a) In General.--Part B of title III of the Energy Policy and 
Conservation Act is amended by inserting after section 324A (42 U.S.C. 
6294a) the following:

``SEC. 324B. VIDEO GAME CONSOLE ENERGY EFFICIENCY STUDY.

    ``(a) Initial Study.--
            ``(1) In general.--Not later than 1 year after the date of 
        enactment of this section, the Secretary shall conduct a study 
        of--
                    ``(A) video game console energy use; and
                    ``(B) opportunities for energy savings regarding 
                that energy use.
            ``(2) Inclusions.--The study under paragraph (1) shall 
        include an assessment of all power-consuming modes and media 
        playback modes of video game consoles.
    ``(b) Action on Completion.--On completion of the initial study 
under subsection (a), the Secretary shall determine, by regulation, 
using the criteria and procedures described in section 325(n)(2), 
whether to initiate a process for establishing minimum energy 
efficiency standards for video game console energy use.
    ``(c) Follow-Up Study.--If the Secretary determines under 
subsection (b) that standards should not be established, the Secretary 
shall conduct a follow-up study in accordance with subsection (a) by 
not later than 3 years after the date of the determination.''.
    (b) Application Date.--Subsection (oo)(1) of section 325 of the 
Energy Policy and Conservation Act (42 U.S.C. 6295) (as redesignated by 
sections 4(d)(1) and 6(d)(1)) is amended by inserting ``or section 
324B'' after ``subsection (l), (u), or (v)'' each place it appears.

SEC. 12. REFRIGERATOR AND FREEZER STANDARDS.

    Section 325(b) of the Energy Policy and Conservation Act (42 U.S.C. 
6295(b)) is amended by striking paragraph (4) and inserting the 
following:
            ``(4) Refrigerators, refrigerator-freezers, and freezers 
        manufactured as of january 1, 2014.--
                    ``(A) Definition of built-in product class.--In 
                this paragraph, the term `built-in product class' means 
                a refrigerator, freezer, or refrigerator with a freezer 
                unit that--
                            ``(i) is 7.75 cubic feet or greater in 
                        total volume and 24 inches or less in cabinet 
                        depth (not including doors, handles, and custom 
                        front panels);
                            ``(ii) is designed to be totally encased by 
                        cabinetry or panels attached during 
                        installation;
                            ``(iii) is designed to accept a custom 
                        front panel or to be equipped with an integral 
                        factory-finished face;
                            ``(iv) is designed to be securely fastened 
                        to adjacent cabinetry, walls, or floors; and
                            ``(v) has 2 or more sides that are not--
                                    ``(I) fully finished; and
                                    ``(II) intended to be visible after 
                                installation.
                    ``(B) Maximum energy use.--
                            ``(i) In general.--Based on the test 
                        procedure in effect as of July 9, 2010, the 
                        maximum energy use allowed in kilowatt hours 
                        per year for each product described in the 
                        table contained in clause (ii) (other than 
                        refrigerators and refrigerator-freezers with 
                        total refrigerated volume exceeding 39 cubic 
                        feet and freezers with total refrigerated 
                        volume exceeding 30 cubic feet) that is 
                        manufactured on or after January 1, 2014, is 
                        specified in the table contained in that 
                        clause.
                            ``(ii) Standards equations.--The allowed 
                        maximum energy use referred to in clause (i) is 
                        as follows:


 
 
----------------------------------------------------------------------------------------------------------------
``Standards Equations
----------------------------------------------------------------------------------------------------------------
Product Description
----------------------------------------------------------------------------------------------------------------
Automatic Defrost Refrigerator-Freezers
----------------------------------------------------------------------------------------------------------------
Top Freezer w/o TTD ice                                  7.35 AV+ 207.0
----------------------------------------------------------------------------------------------------------------
Top Freezer w/ TTD ice                                   7.65 AV+ 267.0
----------------------------------------------------------------------------------------------------------------
Side Freezer w/o TTD ice                                 3.68 AV+ 380.6
----------------------------------------------------------------------------------------------------------------
Side Freezer w/ TTD ice                                  7.58 AV+304.5
----------------------------------------------------------------------------------------------------------------
Bottom Freezer w/o TTD ice                               3.68 AV+ 367.2
----------------------------------------------------------------------------------------------------------------
Bottom Freezer w/ TTD ice                                4.0 AV+ 431.2
----------------------------------------------------------------------------------------------------------------
Manual & Partial Automatic Refrigerator-Freezers
----------------------------------------------------------------------------------------------------------------
Manual Defrost                                           7.06 AV+ 198.7
----------------------------------------------------------------------------------------------------------------
Partial Automatic                                        7.06 AV+198.7
----------------------------------------------------------------------------------------------------------------
All Refrigerators
----------------------------------------------------------------------------------------------------------------
Manual Defrost                                           7.06AV+198.7
----------------------------------------------------------------------------------------------------------------
Automatic Defrost                                        7.35 AV+ 207.0
----------------------------------------------------------------------------------------------------------------
All Freezers
----------------------------------------------------------------------------------------------------------------
Upright with manual defrost                              5.66 AV+ 193.7
----------------------------------------------------------------------------------------------------------------
Upright with automatic defrost                           8.70 AV+ 228.3
----------------------------------------------------------------------------------------------------------------
Chest with manual defrost                                7.41 AV+ 107.8
----------------------------------------------------------------------------------------------------------------
Chest with automatic defrost                             10.33 AV+ 148.1
----------------------------------------------------------------------------------------------------------------
Automatic Defrost Refrigerator-Freezers-Compact Size
----------------------------------------------------------------------------------------------------------------
Top Freezer and Bottom Freezer                           10.80 AV+ 301.8
----------------------------------------------------------------------------------------------------------------
Side Freezer                                             6.08 AV+ 400.8
----------------------------------------------------------------------------------------------------------------
Manual & Partial Automatic Refrigerator-Freezers-Compact Size
----------------------------------------------------------------------------------------------------------------
Manual Defrost                                           8.03 AV+ 224.3
----------------------------------------------------------------------------------------------------------------
Partial Automatic                                        5.25 AV+ 298.5
----------------------------------------------------------------------------------------------------------------
All Refrigerators-Compact Size
----------------------------------------------------------------------------------------------------------------
Manual defrost                                           8.03 AV+ 224.3
----------------------------------------------------------------------------------------------------------------
Automatic defrost                                        9.53 AV+ 266.3
----------------------------------------------------------------------------------------------------------------
All Freezers-Compact Size
----------------------------------------------------------------------------------------------------------------
Upright with manual defrost                              8.80 AV+ 225.7
----------------------------------------------------------------------------------------------------------------
Upright with automatic defrost                           10.26 AV+ 351.9
----------------------------------------------------------------------------------------------------------------
Chest                                                    9.41AV+ 136.8
----------------------------------------------------------------------------------------------------------------
Automatic Defrost Refrigerator-Freezers-Built-ins
----------------------------------------------------------------------------------------------------------------
Top Freezer w/o TTD ice                                  7.84 AV+ 220.8
----------------------------------------------------------------------------------------------------------------
Side Freezer w/o TTD ice                                 3.93 AV+ 406.0
----------------------------------------------------------------------------------------------------------------
Side Freezer w/ TTD ice                                  8.08 AV+ 324.8
----------------------------------------------------------------------------------------------------------------
Bottom Freezer w/o TTD ice                               3.91 AV+ 390.2
----------------------------------------------------------------------------------------------------------------
Bottom Freezer w/ TTD ice                                4.25 AV+ 458.2
----------------------------------------------------------------------------------------------------------------
All Refrigerators-Built-ins
----------------------------------------------------------------------------------------------------------------
Automatic Defrost                                        7.84 AV+ 220.8
----------------------------------------------------------------------------------------------------------------
All Freezers-Built-ins
----------------------------------------------------------------------------------------------------------------
Upright with automatic defrost                           9.32 AV+ 244.6.
----------------------------------------------------------------------------------------------------------------

                            ``(iii) Final rules.--
                                    ``(I) In general.--Except as 
                                provided in subclause (II), after the 
                                date of publication of each test 
                                procedure change made pursuant to 
                                section 323(b)(19), in accordance with 
                                the procedures described in section 
                                323(e)(2), the Secretary shall publish 
                                final rules to amend the standards 
                                specified in the table contained in 
                                clause (ii).
                                    ``(II) Exception.--The standards 
                                amendment made pursuant to the test 
                                procedure change required under section 
                                323(b)(19)(B) shall be based on the 
                                difference between--
                                            ``(aa) the average measured 
                                        automatic ice maker energy use 
                                        of a representative sample for 
                                        each product class; and
                                            ``(bb) the value assumed by 
                                        the Department of Energy for 
                                        ice maker energy use in the 
                                        test procedure published 
                                        pursuant to section 
                                        323(b)(19)(A).
                                    ``(III) Applicability.--Section 
                                323(e)(3) shall not apply to the rules 
                                described in this clause.
                            ``(iv) Final rule.--The Secretary shall 
                        publish any final rule required by clause (iii) 
                        by not later than the later of the date that is 
                        180 days after--
                                    ``(I) the date of enactment of this 
                                clause; or
                                    ``(II) the date of publication of a 
                                final rule to amend the test procedure 
                                described in section 323(b)(19).
                            ``(v) New product classes.--The Secretary 
                        may establish 1 or more new product classes as 
                        part of the final amended standard adopted 
                        pursuant to the test procedure change required 
                        under section 323(b)(19)(B) if the 1 or more 
                        new product classes are needed to distinguish 
                        among products with automatic icemakers.
                            ``(vi) Effective dates of standards.--
                                    ``(I) Standards amendment for first 
                                revised test procedure.--A standards 
                                amendment adopted pursuant to a test 
                                procedure change required under section 
                                323(b)(19)(A) shall apply to any 
                                product manufactured as of January 1, 
                                2014.
                                    ``(II) Standards amendment after 
                                revised test procedure for icemaker 
                                energy.--An amendment adopted pursuant 
                                to a test procedure change required 
                                under section 323(b)(19)(B) shall apply 
                                to any product manufactured as of the 
                                date that is 3 years after the date of 
                                publication of the final rule amending 
                                the standards.
                            ``(vii) Slope and intercept adjustments.--
                                    ``(I) In general.--With respect to 
                                refrigerators, freezers, and 
                                refrigerator-freezers, the Secretary 
                                may, by rule, adjust the slope and 
                                intercept of the equations specified in 
                                the table contained in clause (ii)--
                                            ``(aa) based on the energy 
                                        use of typical products of 
                                        various sizes in a product 
                                        class; and
                                            ``(bb) if the average 
                                        energy use for each of the 
                                        classes is the same under the 
                                        new equations as under the 
                                        equations specified in the 
                                        table contained in clause (ii).
                                    ``(II) Deadline.--If the Secretary 
                                adjusts the slope and intercept of an 
                                equation described in subclause (I), 
                                the Secretary shall publish the final 
                                rule containing the adjustment by not 
                                later than July 1, 2011.
                            ``(viii) Effect.--A final rule published 
                        under clause (iii) pursuant to the test 
                        procedure change required under section 
                        323(b)(19)(B) or pursuant to clause (iv) shall 
                        not be considered to be an amendment to the 
                        standard for purposes of section 325(m).''.

SEC. 13. ROOM AIR CONDITIONER STANDARDS.

    Section 325(c) of the Energy Policy and Conservation Act (42 U.S.C. 
6295(c)) is amended by adding at the end the following:
            ``(3) Minimum energy efficiency ratio of room air 
        conditioners manufactured on or after june 1, 2014.--
                    ``(A) In general.--Based on the test procedure in 
                effect as of July 9, 2010, the minimum energy 
                efficiency ratios of room air conditioners manufactured 
                on or after June 1, 2014, shall not be less than that 
                specified in the table contained in subparagraph (B).
                    ``(B) Minimum energy efficiency ratios.--The 
                minimum energy efficiency ratios referred to in 
                subparagraph (A) are as follows:


----------------------------------------------------------------------------------------------------------------
                            ``Product Description                                         Minimum EER
----------------------------------------------------------------------------------------------------------------
Without Reverse Cycle w/Louvers
----------------------------------------------------------------------------------------------------------------
<6,000 Btu/h                                                                                                11.2
----------------------------------------------------------------------------------------------------------------
6,000 to 7,999 Btu/h                                                                                        11.2
----------------------------------------------------------------------------------------------------------------
8,000-13,999 Btu/h                                                                                          11.0
----------------------------------------------------------------------------------------------------------------
14,000 to 19,999 Btu/h                                                                                      10.8
----------------------------------------------------------------------------------------------------------------
20,000-27,999 Btu/h                                                                                          9.4
----------------------------------------------------------------------------------------------------------------
$28,000 Btu/h                                                                                                9.0
----------------------------------------------------------------------------------------------------------------
Without Reverse Cycle w/o Louvers
----------------------------------------------------------------------------------------------------------------
<6,000 Btu/h                                                                                                10.2
----------------------------------------------------------------------------------------------------------------
6,000 to 7,999 Btu/h                                                                                        10.2
----------------------------------------------------------------------------------------------------------------
8,000-10,999 Btu/h                                                                                           9.7
----------------------------------------------------------------------------------------------------------------
11,000-13,999 Btu/h                                                                                          9.6
----------------------------------------------------------------------------------------------------------------
14,000 to 19,999 Btu/h                                                                                       9.4
----------------------------------------------------------------------------------------------------------------
$20,000 Btu/h                                                                                                9.4
----------------------------------------------------------------------------------------------------------------
With Reverse Cycle
----------------------------------------------------------------------------------------------------------------
<20,000 w/Louvers Btu/h                                                                                      9.9
----------------------------------------------------------------------------------------------------------------
$ 20,000 w/Louvers Btu/h                                                                                     9.4
----------------------------------------------------------------------------------------------------------------
<14,000 w/o Louvers Btu/h                                                                                    9.4
----------------------------------------------------------------------------------------------------------------
$14,000 w/o Louvers Btu/h                                                                                    8.8
----------------------------------------------------------------------------------------------------------------
Casement
----------------------------------------------------------------------------------------------------------------
Casement Only                                                                                                9.6
----------------------------------------------------------------------------------------------------------------
Casement-Slider                                                                                            10.5.
----------------------------------------------------------------------------------------------------------------

                    ``(C) Final rule.--
                            ``(i) In general.--The final rule to amend 
                        the room air conditioner test procedure adopted 
                        pursuant to section 323(b)(20)(C) shall amend 
                        the standards specified in the table contained 
                        in subparagraph (B) in accordance with the 
                        procedures described in section 323(e)(2).
                            ``(ii) Standby and off mode energy 
                        consumption.--
                                    ``(I) In general.--The Secretary 
                                shall integrate standby and off mode 
                                energy consumption into the amended 
                                energy efficiency ratios standards 
                                required under clause (i).
                                    ``(II) Requirements.--The amended 
                                standards described in subclause (I) 
                                shall reflect the levels of standby and 
                                off mode energy consumption that meet 
                                the criteria described in section 
                                325(o).
                            ``(iii) Applicability.--
                                    ``(I) Amendment of standard.--
                                Section 323(e)(3) shall not apply to 
                                the amended standards described in 
                                clause (i).
                                    ``(II) Amended standards.--The 
                                amended standards required by this 
                                subparagraph shall apply to products 
                                manufactured on or after June 1, 
                                2014.''.

SEC. 14. UNIFORM EFFICIENCY DESCRIPTOR FOR COVERED WATER HEATERS.

    Section 325(e) of the Energy Policy and Conservation Act (42 U.S.C. 
6295(e)) is amended by adding at the end the following:
            ``(5) Uniform efficiency descriptor for covered water 
        heaters.--
                    ``(A) Definitions.--In this paragraph:
                            ``(i) Covered water heater.--The term 
                        `covered water heater' means--
                                    ``(I) a water heater; and
                                    ``(II) a storage water heater, 
                                instantaneous water heater, and unfired 
                                water storage tank (as defined in 
                                section 340).
                            ``(ii) Final rule.--The term `final rule' 
                        means the final rule published under this 
                        paragraph.
                    ``(B) Publication of final rule.--Not later than 
                180 days after the date of enactment of this paragraph, 
                the Secretary shall publish a final rule that 
                establishes a uniform efficiency descriptor and 
                accompanying test methods for covered water heaters.
                    ``(C) Purpose.--The purpose of the final rule shall 
                be to replace with a uniform efficiency descriptor--
                            ``(i) the energy factor descriptor for 
                        water heaters established under this 
                        subsection; and
                            ``(ii) the thermal efficiency and standby 
                        loss descriptors for storage water heaters, 
                        instantaneous water heaters, and unfired water 
                        storage tanks established under section 
                        342(a)(5).
                    ``(D) Effect of final rule.--
                            ``(i) In general.--Notwithstanding any 
                        other provision of this title, effective 
                        beginning on the effective date of the final 
                        rule, the efficiency standard for covered water 
                        heaters shall be denominated according to the 
                        efficiency descriptor established by the final 
                        rule.
                            ``(ii) Effective date.--The final rule 
                        shall take effect 1 year after the date of 
                        publication of the final rule under 
                        subparagraph (B).
                    ``(E) Conversion factor.--
                            ``(i) In general.--The Secretary shall 
                        develop a mathematical conversion factor for 
                        converting the measurement of efficiency for 
                        covered water heaters from the test procedures 
                        in effect on the date of enactment of this 
                        paragraph to the new energy descriptor 
                        established under the final rule.
                            ``(ii) Application.--The conversion factor 
                        shall apply to models of covered water heaters 
                        affected by the final rule and tested prior to 
                        the effective date of the final rule.
                            ``(iii) Effect on efficiency 
                        requirements.--The conversion factor shall not 
                        affect the minimum efficiency requirements for 
                        covered water heaters otherwise established 
                        under this title.
                            ``(iv) Use.--During the period described in 
                        clause (v), a manufacturer may apply the 
                        conversion factor established by the Secretary 
                        to rerate existing models of covered water 
                        heaters that are in existence prior to the 
                        effective date of the rule described in clause 
                        (v)(II) to comply with the new efficiency 
                        descriptor.
                            ``(v) Period.--Subclause (E) shall apply 
                        during the period--
                                    ``(I) beginning on the date of 
                                publication of the conversion factor in 
                                the Federal Register; and
                                    ``(II) ending on April 16, 2015.
                    ``(F) Exclusions.--The final rule may exclude a 
                specific category of covered water heaters from the 
                uniform efficiency descriptor established under this 
                paragraph if the Secretary determines that the category 
                of water heaters--
                            ``(i) does not have a residential use and 
                        can be clearly described in the final rule; and
                            ``(ii) are effectively rated using the 
                        thermal efficiency and standby loss descriptors 
                        applied (as of the date of enactment of this 
                        paragraph) to the category under section 
                        342(a)(5).
                    ``(G) Options.--The descriptor set by the final 
                rule may be--
                            ``(i) a revised version of the energy 
                        factor descriptor in use as of the date of 
                        enactment of this paragraph;
                            ``(ii) the thermal efficiency and standby 
                        loss descriptors in use as of that date;
                            ``(iii) a revised version of the thermal 
                        efficiency and standby loss descriptors;
                            ``(iv) a hybrid of descriptors; or
                            ``(v) a new approach.
                    ``(H) Application.--The efficiency descriptor and 
                accompanying test method established under the final 
                rule shall apply, to the maximum extent practicable, to 
                all water heating technologies in use as of the date of 
                enactment of this paragraph and to future water heating 
                technologies.
                    ``(I) Participation.--The Secretary shall invite 
                interested stakeholders to participate in the 
                rulemaking process used to establish the final rule.
                    ``(J) Testing of alternative descriptors.--In 
                establishing the final rule, the Secretary shall 
                contract with the National Institute of Standards and 
                Technology, as necessary, to conduct testing and 
                simulation of alternative descriptors identified for 
                consideration.
                    ``(K) Existing covered water heaters.--A covered 
                water heater shall be considered to comply with the 
                final rule on and after the effective date of the final 
                rule and with any revised labeling requirements 
                established by the Federal Trade Commission to carry 
                out the final rule if the covered water heater--
                            ``(i) was manufactured prior to the 
                        effective date of the final rule; and
                            ``(ii) complied with the efficiency 
                        standards and labeling requirements in effect 
                        prior to the final rule.''.

SEC. 15. CLOTHES DRYERS.

    Section 325(g)(4) of the Energy Policy and Conservation Act (42 
U.S.C. 6295(g)(4)) is amended by adding at the end the following:
                    ``(D) Minimum energy factors for clothes dryers.--
                            ``(i) In general.--Based on the test 
                        procedure in effect as of July 9, 2010, clothes 
                        dryers manufactured on or after January 1, 
                        2015, shall comply with the minimum energy 
                        factors specified in the table contained in 
                        clause (ii).
                            ``(ii) New standards.--The minimum energy 
                        factors referred to in clause (i) are as 
                        follows:


----------------------------------------------------------------------------------------------------------------
                                       ``Product Description                                             EF
----------------------------------------------------------------------------------------------------------------
Vented Electric Standard                                                                                   3.17
----------------------------------------------------------------------------------------------------------------
Vented Electric Compact 120V                                                                               3.29
----------------------------------------------------------------------------------------------------------------
Vented Electric Compact 240V                                                                               3.05
----------------------------------------------------------------------------------------------------------------
Vented Gas                                                                                                 2.81
----------------------------------------------------------------------------------------------------------------
Vent-Less Electric Compact 240V                                                                            2.37
----------------------------------------------------------------------------------------------------------------
Vent-Less Electric Combination Washer/Dryer                                                                1.95
----------------------------------------------------------------------------------------------------------------

                            ``(iii) Final rule.--
                                    ``(I) Requirements.--
                                            ``(aa) In general.--Except 
                                        as provided in item (bb), the 
                                        final rule to amend the clothes 
                                        dryer test procedure adopted 
                                        pursuant to section 
                                        323(b)(20)(B) shall amend the 
                                        energy factors standards 
                                        specified in the table 
                                        contained in clause (ii) in 
                                        accordance with the procedures 
                                        described in section 323(e)(2).
                                            ``(bb) Exception.--To 
                                        establish a representative 
                                        sample of compliant products, 
                                        the Secretary shall select a 
                                        sample of minimally compliant 
                                        dryers that automatically 
                                        terminate the drying cycle at 
                                        not less than 4 percent 
                                        remaining moisture content.
                                    ``(II) Standby and off mode energy 
                                consumption.--
                                            ``(aa) Integration.--The 
                                        Secretary shall integrate 
                                        standby and off mode energy 
                                        consumption into the amended 
                                        standards required under 
                                        subclause (I).
                                            ``(bb) Requirements.--The 
                                        amended standards described in 
                                        item (aa) shall reflect levels 
                                        of standby and off mode energy 
                                        consumption that meet the 
                                        criteria described in section 
                                        325(o).
                                    ``(III) Applicability.--
                                            ``(aa) Amendment of 
                                        standard.--Section 323(e)(3) 
                                        shall not apply to the amended 
                                        standards described in 
                                        subclause (I).
                                            ``(bb) Amended standards.--
                                        The amended standards required 
                                        by this clause shall apply to 
                                        products manufactured on or 
                                        after January 1, 2015.''.

SEC. 16. STANDARDS FOR CLOTHES WASHERS.

    Section 325(g)(9) of the Energy Policy and Conservation Act (42 
U.S.C. 6295(g)(9)) is amended by striking subparagraph (B) and 
inserting the following:
                    ``(B) Amendment of standards.--
                            ``(i) Products manufactured as of january 
                        1, 2015.--
                                    ``(I) In general.--Based on the 
                                test procedure in effect as of July 9, 
                                2010, clothes washers manufactured as 
                                of January 1, 2015, shall comply with 
                                the minimum modified energy factors and 
                                maximum water factors specified in the 
                                table contained in subclause (II).
                                    ``(II) Standards.--The minimum 
                                modified energy factors and maximum 
                                water factors referred to in subclause 
                                (I) are as follows:


 
 
----------------------------------------------------------------------------------------------------------------
                                                        ``MEF   WF
----------------------------------------------------------------------------------------------------------------
Top Loading--Standard                                    1.72   8.0
----------------------------------------------------------------------------------------------------------------
Top Loading--Compact                                     1.26   14.0
----------------------------------------------------------------------------------------------------------------
Front Loading--Standard                                   2.2   4.5
----------------------------------------------------------------------------------------------------------------
Front Loading--Compact (less than 1.6 cu. ft.            1.72   8.0.
 capacity)
----------------------------------------------------------------------------------------------------------------

                            ``(ii) Products manufactured on or after 
                        january 1, 2018.--
                                    ``(I) In general.--Based on the 
                                test procedure in effect as of July 9, 
                                2010, top-loading clothes washers 
                                manufactured on or after January 1, 
                                2018, shall comply with the minimum 
                                modified energy factors and maximum 
                                water factors specified in the table 
                                contained in subclause (II).
                                    ``(II) Standards.--The minimum 
                                modified energy factors and maximum 
                                water factors referred to in subclause 
                                (I) are as follows:


 
 
----------------------------------------------------------------------------------------------------------------
                                                        ``MEF   WF
----------------------------------------------------------------------------------------------------------------
Top Loading--Standard                                     2.0   6.0
----------------------------------------------------------------------------------------------------------------
Top Loading--Compact                                     1.81   11.6.
----------------------------------------------------------------------------------------------------------------

                            ``(iii) Final rule.--
                                    ``(I) In general.--The final rule 
                                to amend the clothes washer test 
                                procedure adopted pursuant to section 
                                323(b)(20)(A) shall amend the standards 
                                described in clauses (i) and (ii) in 
                                accordance with the procedures 
                                described in section 323(e)(2).
                                    ``(II) Standby and off mode energy 
                                consumption.--
                                            ``(aa) Integration.--The 
                                        Secretary shall integrate 
                                        standby and off mode energy 
                                        consumption into the amended 
                                        modified energy factor 
                                        standards required under 
                                        subclause (I).
                                            ``(bb) Requirements.--The 
                                        amended modified energy factor 
                                        standards described in item 
                                        (aa) shall reflect levels of 
                                        standby and off mode energy 
                                        consumption that meet the 
                                        criteria described in section 
                                        325(o).
                                    ``(III) Applicability.--
                                            ``(aa) Amendment of 
                                        standard.--Section 323(e)(3) 
                                        shall not apply to the amended 
                                        standards described in 
                                        subclause (I).
                                            ``(bb) Amended standards 
                                        for products manufactured on or 
                                        after january 1, 2015.--Amended 
                                        standards required by this 
                                        clause that are based on clause 
                                        (i) shall apply to products 
                                        manufactured on or after 
                                        January 1, 2015.
                                            ``(cc) Amended standards 
                                        for products manufactured on or 
                                        after january 1, 2018.--Amended 
                                        standards required by this 
                                        clause that are based on clause 
                                        (ii) shall apply to products 
                                        manufactured on or after 
                                        January 1, 2018.''.

SEC. 17. DISHWASHERS.

    Section 325(g)(10) of the Energy Policy and Conservation Act (42 
U.S.C. 6295(g)(10)) is amended--
            (1) by striking subparagraph (A);
            (2) by redesignating subparagraph (B) as subparagraph (D); 
        and
            (3) by inserting before subparagraph (D) (as redesignated 
        by paragraph (2)) the following:
                    ``(A) Dishwashers manufactured on or after january 
                1, 2010.--A dishwasher manufactured on or after January 
                1, 2010, shall--
                            ``(i) for a standard size dishwasher, not 
                        exceed 355 kilowatt hours per year and 6.5 
                        gallons per cycle; and
                            ``(ii) for a compact size dishwasher, not 
                        exceed 260 kilowatt hours per year and 4.5 
                        gallons per cycle.
                    ``(B) Dishwashers manufactured on or after january 
                1, 2013.--A dishwasher manufactured on or after January 
                1, 2013, shall--
                            ``(i) for a standard size dishwasher, not 
                        exceed 307 kilowatt hours per year and 5.0 
                        gallons per cycle; and
                            ``(ii) for a compact size dishwasher, not 
                        exceed 222 kilowatt hours per year and 3.5 
                        gallons per cycle.
                    ``(C) Requirements of final rules.--
                            ``(i) In general.--Any final rule to amend 
                        the dishwasher test procedure after July 9, 
                        2010, and before January 1, 2013, shall amend 
                        the standards described in subparagraph (B) in 
                        accordance with the procedures described in 
                        section 323(e)(2).
                            ``(ii) Applicability.--
                                    ``(I) Amendment of standard.--
                                Section 323(e)(3) shall not apply to 
                                the amended standards described in 
                                clause (i).
                                    ``(II) Amended standards.--The 
                                amended standards required by this 
                                subparagraph shall apply to products 
                                manufactured on or after January 1, 
                                2013.''.

SEC. 18. STANDARDS FOR CERTAIN INCANDESCENT REFLECTOR LAMPS AND 
              REFLECTOR LAMPS.

    Section 325(i) of the Energy Policy and Conservation Act (42 U.S.C. 
6295(i)) is amended by adding at the end the following:
            ``(9) Certain incandescent reflector lamps.--
                    ``(A) In general.--Not later than July 1, 2011, the 
                Secretary shall publish a final rule establishing 
                standards for incandescent reflector lamp types 
                described in paragraph (1)(D)(i).
                    ``(B) Effective date.--The standards described in 
                subparagraph (A) shall take effect on July 1, 2013.
                    ``(C) Standards.--In conducting a rulemaking for 
                incandescent reflector lamps under this paragraph after 
                the date of enactment of this paragraph, the Secretary 
                shall consider the standards for all incandescent 
                reflector lamps, including lamp types described in 
                paragraph (1)(D)(i).
            ``(10) Reflector lamps.--
                    ``(A) In general.--Not later than January 1, 2015, 
                the Secretary shall publish a final rule establishing 
                and amending standards for reflector lamps, including 
                incandescent reflector lamps.
                    ``(B) Administration.--In conducting the rulemaking 
                for reflector lamps under this paragraph, the Secretary 
                shall consider--
                            ``(i) incandescent and nonincandescent 
                        technologies; and
                            ``(ii) a new metric, other than lumens per 
                        watt, that is based on the photometric 
                        distribution of those lamps.
                    ``(C) Effective date.--The standards described in 
                subparagraph (A) shall take effect not earlier than the 
                date that is 3 years after the date of publication of 
                the final rule, as determined by the Secretary.''.

SEC. 19. PETITION FOR AMENDED STANDARDS.

    Section 325(n) of the Energy Policy and Conservation Act (42 U.S.C. 
6295(n)) is amended--
            (1) by redesignating paragraph (3) as paragraph (5); and
            (2) by inserting after paragraph (2) the following:
            ``(3) Notice of decision.--Not later than 180 days after 
        the date of receiving a petition, the Secretary shall publish 
        in the Federal Register a notice of, and explanation for, the 
        decision of the Secretary to grant or deny the petition.
            ``(4) New or amended standards.--Not later than 3 years 
        after the date of granting a petition for new or amended 
        standards, the Secretary shall publish in the Federal 
        Register--
                    ``(A) a final rule that contains the new or amended 
                standards; or
                    ``(B) a determination that no new or amended 
                standards are necessary.''.

SEC. 20. EFFICIENCY STANDARDS FOR CLASS A EXTERNAL POWER SUPPLIES.

    Section 325(u)(3) of the Energy Policy and Conservation Act (42 
U.S.C. 6295(u)(3)) is amended--
            (1) in subparagraph (A), by striking ``(D)'' and inserting 
        ``(E)''; and
            (2) by adding at the end the following:
                    ``(E) Nonapplication of no-load mode energy 
                efficiency standards to external power supplies for 
                certain security or life safety alarms or surveillance 
                systems.--
                            ``(i) Definition of security or life safety 
                        alarm or surveillance system.--In this 
                        subparagraph:
                                    ``(I) In general.--The term 
                                `security or life safety alarm or 
                                surveillance system' means equipment 
                                designed and marketed to perform any of 
                                the following functions (on a 
                                continuous basis):
                                            ``(aa) Monitor, detect, 
                                        record, or provide notification 
                                        of intrusion or access to real 
                                        property or physical assets or 
                                        notification of threats to life 
                                        safety.
                                            ``(bb) Deter or control 
                                        access to real property or 
                                        physical assets, or prevent the 
                                        unauthorized removal of 
                                        physical assets.
                                            ``(cc) Monitor, detect, 
                                        record, or provide notification 
                                        of fire, gas, smoke, flooding, 
                                        or other physical threats to 
                                        real property, physical assets, 
                                        or life safety.
                                    ``(II) Exclusion.--The term 
                                `security or life safety alarm or 
                                surveillance system' does not include 
                                any product with a principal function 
                                other than life safety, security, or 
                                surveillance that--
                                            ``(aa) is designed and 
                                        marketed with a built-in alarm 
                                        or theft-deterrent feature; or
                                            ``(bb) does not operate 
                                        necessarily and continuously in 
                                        active mode.
                            ``(ii) Nonapplication of no-load mode 
                        requirements.--The No-Load Mode energy 
                        efficiency standards established by this 
                        paragraph shall not apply to an external power 
                        supply manufactured before July 1, 2017, that--
                                    ``(I) is an AC-to-AC external power 
                                supply;
                                    ``(II) has a nameplate output of 20 
                                watts or more;
                                    ``(III) is certified to the 
                                Secretary as being designed to be 
                                connected to a security or life safety 
                                alarm or surveillance system component; 
                                and
                                    ``(IV) on establishment within the 
                                External Power Supply International 
                                Efficiency Marking Protocol, as 
                                referenced in the `Energy Star Program 
                                Requirements for Single Voltage 
                                External AC-DC and AC-AC Power 
                                Supplies', published by the 
                                Environmental Protection Agency, of a 
                                distinguishing mark for products 
                                described in this clause, is 
                                permanently marked with the 
                                distinguishing mark.
                            ``(iii) Administration.--In carrying out 
                        this subparagraph, the Secretary shall--
                                    ``(I) require, with appropriate 
                                safeguard for the protection of 
                                confidential business information, the 
                                submission of unit shipment data on an 
                                annual basis; and
                                    ``(II) restrict the eligibility of 
                                external power supplies for the 
                                exemption provided under this 
                                subparagraph on a finding that a 
                                substantial number of the external 
                                power supplies are being marketed to or 
                                installed in applications other than 
                                security or life safety alarm or 
                                surveillance systems.''.

SEC. 21. PROHIBITED ACTS.

    Section 332(a) of the Energy Policy and Conservation Act (42 U.S.C. 
6302(a)) is amended--
            (1) in paragraph (1), by striking ``for any manufacturer or 
        private labeler to distribute'' and inserting ``for any 
        manufacturer (or representative of a manufacturer), 
        distributor, retailer, or private labeler to offer for sale or 
        distribute'';
            (2) by striking paragraph (5) and inserting the following:
            ``(5) for any manufacturer (or representative of a 
        manufacturer), distributor, retailer, or private labeler--
                    ``(A) to offer for sale or distribute in commerce 
                any new covered product that is not in conformity with 
                an applicable energy conservation standard established 
                in or prescribed under this part; or
                    ``(B) if the standard is a regional standard that 
                is more stringent than the base national standard, to 
                offer for sale or distribute in commerce any new 
                covered product having knowledge (consistent with the 
                definition of `knowingly' in section 333(b)) that the 
                product will be installed at a location covered by a 
                regional standard established in or prescribed under 
                this part and will not be in conformity with the 
                standard;'';
            (3) in paragraph (6) (as added by section 306(b)(2) of 
        Public Law 110-140 (121 Stat. 1559)), by striking the period at 
        the end and inserting a semicolon;
            (4) by redesignating paragraph (6) (as added by section 
        321(e)(3) of Public Law 110-140 (121 Stat. 1586)) as paragraph 
        (7);
            (5) in paragraph (7) (as so redesignated)--
                    (A) by striking ``for any manufacturer, 
                distributor, retailer, or private labeler to 
                distribute'' and inserting ``for any manufacturer (or 
                representative of a manufacturer), distributor, 
                retailer, or private labeler to offer for sale or 
                distribute''; and
                    (B) by striking the period at the end and inserting 
                a semicolon; and
            (6) by inserting after paragraph (7) (as so redesignated) 
        the following:
            ``(8) for any manufacturer or private labeler to distribute 
        in commerce any new covered product that has not been properly 
        certified in accordance with the requirements established in or 
        prescribed under this part;
            ``(9) for any manufacturer or private labeler to distribute 
        in commerce any new covered product that has not been properly 
        tested in accordance with the requirements established in or 
        prescribed under this part; and
            ``(10) for any manufacturer or private labeler to violate 
        any regulation lawfully promulgated to implement any provision 
        of this part.''.

SEC. 22. OUTDOOR LIGHTING.

    (a) Definitions.--
            (1) Covered equipment.--Section 340(1) of the Energy Policy 
        and Conservation Act (42 U.S.C. 6311(1)) is amended--
                    (A) by redesignating subparagraph (L) as 
                subparagraph (O); and
                    (B) by inserting after subparagraph (K) the 
                following:
                    ``(L) Pole-mounted outdoor luminaires.
                    ``(M) High light output double-ended quartz halogen 
                lamps.
                    ``(N) General purpose mercury vapor lamps.''.
            (2) Industrial equipment.--Section 340(2)(B) of the Energy 
        Policy and Conservation Act (42 U.S.C. 6311(2)(B)) is amended--
                    (A) by striking ``and'' before ``unfired hot 
                water''; and
                    (B) by inserting after ``tanks'' the following: ``, 
                pole-mounted outdoor luminaires, high light output 
                double-ended quartz halogen lamps, and general purpose 
                mercury vapor lamps''.
            (3) New definitions.--Section 340 of the Energy Policy and 
        Conservation Act (42 U.S.C. 6311) is amended--
                    (A) by redesignating paragraphs (22) and (23) (as 
                amended by sections 312(a)(2) and 314(a) of the Energy 
                Independence and Security Act of 2007 (121 Stat. 1564, 
                1569)) as paragraphs (23) and (24), respectively; and
                    (B) by adding at the end the following:
            ``(25) Area luminaire.--The term `area luminaire' means a 
        luminaire intended for lighting parking lots and general areas 
        that--
                    ``(A) is designed to mount on a pole using an arm, 
                pendant, or vertical tenon;
                    ``(B) has an opaque top or sides, but may contain a 
                transmissive ornamental element;
                    ``(C) has an optical aperture that is open or 
                enclosed with a flat, sag, or drop lens;
                    ``(D) is mounted in a fixed position with the 
                optical aperture near horizontal, or tilted up; and
                    ``(E) has photometric output measured using Type C 
                photometry per IESNA LM-75-01.
            ``(26) Decorative posttop luminaire.--The term `decorative 
        posttop luminaire' means a luminaire with--
                    ``(A) open or transmissive sides that is designed 
                to be mounted directly over a pole using a vertical 
                tenon or by fitting the luminaire directly into the 
                pole; and
                    ``(B) photometric output measured using Type C 
                photometry per IESNA LM-75-01.
            ``(27) Dusk-to-dawn luminaire.--The term `dusk-to-dawn 
        luminaire' means a fluorescent, induction, or high intensity 
        discharge luminaire that--
                    ``(A) is designed to be mounted on a horizontal or 
                horizontally slanted tenon or arm;
                    ``(B) has an optical assembly that is coaxial with 
                the axis of symmetry of the light source;
                    ``(C) has an optical assembly that is--
                            ``(i) a reflector or lamp enclosure that 
                        surrounds the light source with an open lower 
                        aperture; or
                            ``(ii) a refractive optical assembly 
                        surrounding the light source with an open or 
                        closed lower aperture;
                    ``(D) contains a receptacle for a photocontrol that 
                enables the operation of the light source and is either 
                coaxial with both the axis of symmetry of the light 
                source and the optical assembly or offset toward the 
                mounting bracket by less than 3 inches, or contains an 
                integral photocontrol; and
                    ``(E) has photometric output measured using Type C 
                photometry per IESNA LM-75-01.
            ``(28) Floodlight luminaire.--The term `floodlight 
        luminaire' means an outdoor luminaire designed with a yoke, 
        knuckle, or other mechanism allowing the luminaire to be aimed 
        40 degrees or more with its photometric distributions 
        established with only Type B photometry in accordance with 
        IESNA LM-75, revised 2001.
            ``(29) General purpose mercury vapor lamp.--The term 
        `general purpose mercury vapor lamp' means a mercury vapor lamp 
        (as defined in section 321) that--
                    ``(A) has a screw base;
                    ``(B) is designed for use in general lighting 
                applications (as defined in section 321);
                    ``(C) is not a specialty application mercury vapor 
                lamp; and
                    ``(D) is designed to operate on a mercury vapor 
                lamp ballast (as defined in section 321) or is a self- 
                ballasted lamp.
            ``(30) High light output double-ended quartz halogen 
        lamp.--The term `high light output double-ended quartz halogen 
        lamp' means a lamp that--
                    ``(A) is designed for general outdoor lighting 
                purposes;
                    ``(B) contains a tungsten filament;
                    ``(C) has a rated initial lumen value of greater 
                than 6,000 and less than 40,000 lumens;
                    ``(D) has at each end a recessed single contact, 
                R7s base;
                    ``(E) has a maximum overall length (MOL) between 4 
                and 11 inches;
                    ``(F) has a nominal diameter less than \3/4\ inch 
                (T6);
                    ``(G) is designed to be operated at a voltage not 
                less than 110 volts and not greater than 200 volts or 
                is designed to be operated at a voltage between 235 
                volts and 300 volts;
                    ``(H) is not a tubular quartz infrared heat lamp; 
                and
                    ``(I) is not a lamp marked and marketed as a Stage 
                and Studio lamp with a rated life of 500 hours or less.
            ``(31) Mean rated lamp lumens.--The term `mean rated lamp 
        lumens' means the rated lumens at--
                    ``(A) 40 percent of rated lamp life for metal 
                halide, induction, and fluorescent lamps; or
                    ``(B) 50 percent of rated lamp life for high 
                pressure sodium lamps.
            ``(32) Outdoor luminaire.--The term `outdoor luminaire' 
        means a luminaire that--
                    ``(A) is intended for outdoor use and suitable for 
                wet locations; and
                    ``(B) may be shipped with or without a lamp.
            ``(33) Pole-mounted outdoor luminaire.--
                    ``(A) In general.--The term `pole-mounted outdoor 
                luminaire' means an outdoor luminaire that is designed 
                to be mounted on an outdoor pole and is--
                            ``(i) an area luminaire;
                            ``(ii) a roadway and highmast luminaire;
                            ``(iii) a decorative posttop luminaire; or
                            ``(iv) a dusk-to-dawn luminaire.
                    ``(B) Exclusions.--The term `pole-mounted outdoor 
                luminaire' does not include--
                            ``(i) a portable luminaire designed for use 
                        at construction sites;
                            ``(ii) a luminaire designed to be used in 
                        emergency conditions that--
                                    ``(I) incorporates a means of 
                                storing energy and a device to switch 
                                the stored energy supply to emergency 
                                lighting loads automatically on failure 
                                of the normal power supply; and
                                    ``(II) is listed and labeled as 
                                Emergency Lighting Equipment;
                            ``(iii) a decorative gas lighting system;
                            ``(iv) a luminaire designed explicitly for 
                        lighting for theatrical purposes, including 
                        performance, stage, film production, and video 
                        production;
                            ``(v) a luminaire designed as theme 
                        elements in theme or amusement parks and that 
                        cannot be used in most general lighting 
                        applications;
                            ``(vi) a luminaire designed explicitly for 
                        hazardous locations meeting the requirements of 
                        Underwriters Laboratories Standard 844-2006, 
                        `Luminaires for Use in Hazardous (Classified) 
                        Locations';
                            ``(vii) a residential pole-mounted 
                        luminaire that is not rated for commercial use 
                        utilizing 1 or more lamps meeting the energy 
                        conservation standards established under 
                        section 325(i) and mounted on a post or pole 
                        not taller than 10.5 feet above ground and not 
                        rated for a power draw of more than 145 watts;
                            ``(viii) a floodlight luminaire;
                            ``(ix) an outdoor luminaire designed for 
                        sports and recreational area use in accordance 
                        with IESNA RP-6 and utilizing an 875 watt or 
                        greater metal halide lamp;
                            ``(x) a decorative posttop luminaire 
                        designed for using high intensity discharge 
                        lamps with total lamp wattage of 150 or less, 
                        or designed for using other lamp types with 
                        total lamp wattage of 50 watts or less;
                            ``(xi) an area luminaire, roadway and 
                        highmast luminaire, or dusk-to-dawn luminaire 
                        designed for using high intensity discharge 
                        lamps or pin-based compact fluorescent lamps 
                        with total lamp wattage of 100 or less, or 
                        other lamp types with total lamp wattage of 50 
                        watts or less; and
                            ``(xii) an area luminaire, roadway and 
                        highmast luminaire, or dusk-to-dawn luminaire 
                        with a backlight rating less than 2 and with 
                        the maximum of the uplight or glare rating 3 or 
                        less.
            ``(34) Roadway and highmast luminaire.--The term `roadway 
        and highmast luminaire' means a luminaire intended for lighting 
        streets and roadways that--
                    ``(A) is designed to mount on a pole by clamping 
                onto the exterior of a horizontal or horizontally 
                slanted, circular cross-section pipe tenon;
                    ``(B) has opaque tops or sides;
                    ``(C) has an optical aperture that is open or 
                enclosed with a flat, sag or drop lens;
                    ``(D) is mounted in a fixed position with the 
                optical aperture near horizontal, or tilted up; and
                    ``(E) has photometric output measured using Type C 
                photometry per IESNA LM-75-01.
            ``(35) Specialty application mercury vapor lamp.--The term 
        `specialty application mercury vapor lamp' means a mercury 
        vapor lamp (as defined in section 321) that is--
                    ``(A) designed only to operate on a specialty 
                application mercury vapor lamp ballast (as defined in 
                section 321); and
                    ``(B) is marked and marketed for specialty 
                applications only.
            ``(36) Target efficacy rating.--The term `target efficacy 
        rating' means a measure of luminous efficacy of a luminaire (as 
        defined in NEMA LE-6-2009).
            ``(37) Tubular quartz infrared heat lamp.--The term 
        `tubular quartz infrared heat lamp' means a double-ended quartz 
        halogen lamp that--
                    ``(A) is marked and marketed as an infrared heat 
                lamp; and
                    ``(B) radiates predominately in the infrared 
                radiation range and in which the visible radiation is 
                not of principle interest.''.
    (b) Standards.--Section 342 of the Energy Policy and Conservation 
Act (42 U.S.C. 6313) is amended by adding at the end the following:
    ``(g) Pole-Mounted Outdoor Luminaires.--
            ``(1) Target efficacy rating, lumen maintenance and power 
        factor requirements.--
                    ``(A) Definition of maximum of uplight or glare 
                rating.--In this paragraph, the term `maximum of 
                uplight or glare rating' means, for any specific 
                outdoor luminaire, the higher of the uplight rating or 
                glare rating of the luminaire.
                    ``(B) Requirements.--Each pole-mounted outdoor 
                luminaire manufactured on or after the date that is 3 
                years after the date of enactment of this subsection 
                shall--
                            ``(i) meet or exceed the target efficacy 
                        ratings in the following table when tested at 
                        full system input watts:

                 ``Area, Roadway or Highmast luminaires
------------------------------------------------------------------------
                                  Maximum of Uplight or Glare rating
------------------------------------------------------------------------
      Backlight Rating           0 or 1         2 or 3         4 or 5
------------------------------------------------------------------------
                   0 or 1              38             38             38
                   2 or 3              38             38             42
                   4 or 5              38             42             43
------------------------------------------------------------------------


             ``Decorative Posttop or Dusk-to-Dawn luminaires
------------------------------------------------------------------------
                                  Maximum of Uplight or Glare rating
------------------------------------------------------------------------
      Backlight Rating           0 or 1         2 or 3         4 or 5
------------------------------------------------------------------------
                   0 or 1              25             25             25
                   2 or 3              25             25             28
                   4 or 5              25             28            28;
------------------------------------------------------------------------

                            ``(ii) use lamps that have a minimum of 0.6 
                        lumen maintenance, as determined in accordance 
                        with IESNA LM-80 for Solid State Lighting 
                        sources or calculated as mean rated lamp lumens 
                        divided by initial rated lamp lumens for other 
                        light sources; and
                            ``(iii) have a power factor equal to or 
                        greater than 0.9 at ballast full power, except 
                        in the case of pole-mounted outdoor luminaires 
                        designed for using high intensity discharge 
                        lamps with a total rated lamp wattage of 150 
                        watts or less, which shall have no power factor 
                        requirement.
            ``(2) Control requirements.--
                    ``(A) In general.--Except as provided in 
                subparagraph (B), each area luminaire manufactured on 
                or after the date that is 3 years after the date of 
                enactment of this subsection shall be sold--
                            ``(i) with integral controls that shall 
                        have the capability of operating the luminaire 
                        at full power and a minimum of 1 reduced power 
                        level plus off, in which case the power 
                        reduction shall be at least 30 percent of the 
                        rated lamp power; or
                            ``(ii) with internal electronics and 
                        connective wiring or hardware (including wire 
                        leads, pigtails, inserts for wires, pin bases, 
                        or the equivalent) that--
                                    ``(I) collectively enable the area 
                                luminaire, if properly connected to an 
                                appropriate control system, to operate 
                                at full power and a minimum of 1 
                                reduced power level plus off, in which 
                                case the reduced power level shall be 
                                at least 30 percent lower than the 
                                rated lamp power in response to signals 
                                sent by controls not integral to the 
                                luminaire as sold, that may be 
                                connected in the field; and
                                    ``(II) have connections from the 
                                components that are easily accessible 
                                in the luminaire housing and have 
                                instructions applicable to appropriate 
                                control system connections that are 
                                included with the luminaire.
                    ``(B) Nonapplication.--The control requirements of 
                this paragraph shall not apply to--
                            ``(i) pole-mounted outdoor luminaires 
                        utilizing probe-start metal halide lamps with 
                        rated lamp power greater than 500 watts 
                        operating in non-base-up positions; or
                            ``(ii) pole-mounted outdoor luminaires 
                        utilizing induction lamps.
                    ``(C) Integral photosensors.--Each pole-mounted 
                outdoor luminaire sold with an integral photosensor 
                shall use an electronic-type photocell.
            ``(3) Rulemaking commencing not later than 60 days after 
        the date of enactment.--
                    ``(A) In general.--Not later than 60 days after the 
                date of enactment of this subsection, the Secretary 
                shall initiate a rulemaking procedure to determine 
                whether the standards in effect for pole-mounted 
                outdoor luminaires should be amended.
                    ``(B) Final rule.--
                            ``(i) Publication.--The Secretary shall 
                        publish a final rule containing the amendments, 
                        if any, not later than January 1, 2013, or the 
                        date that is 33 months after the date of 
                        enactment of this subsection, whichever is 
                        later.
                            ``(ii) Application.--Any amendments shall 
                        apply to products manufactured on or after 
                        January 1, 2016, or the date that is 3 years 
                        after the final rule is published in the 
                        Federal Register, whichever is later.
                    ``(C) Review.--
                            ``(i) In general.--As part of the 
                        rulemaking required under this paragraph, the 
                        Secretary shall review and may amend the 
                        definitions, exclusions, test procedures, power 
                        factor standards, lumen maintenance 
                        requirements, labeling requirements, and 
                        additional control requirements, including 
                        dimming functionality, for all pole-mounted 
                        outdoor luminaires.
                            ``(ii) Factors.--The review of the 
                        Secretary shall include consideration of--
                                    ``(I) obstacles to compliance and 
                                whether compliance is evaded by 
                                substitution of nonregulated luminaires 
                                for regulated luminaires or allowing 
                                luminaires to comply with the standards 
                                established under this part based on 
                                use of non-standard lamps, as provided 
                                for in section 343(a)(10)(D)(i)(II);
                                    ``(II) statistical data relating to 
                                pole-mounted outdoor luminaires that--
                                            ``(aa) the Secretary shall 
                                        request not later than 120 days 
                                        after the date of enactment of 
                                        this subsection from all 
                                        identifiable manufacturers of 
                                        pole-mounted outdoor 
                                        luminaires, directly from 
                                        manufacturers of pole-mounted 
                                        outdoor luminaires or, in the 
                                        case of members of the National 
                                        Electrical Manufacturers 
                                        Association, from the National 
                                        Electrical Manufacturers 
                                        Association;
                                            ``(bb) is considered 
                                        necessary for the rulemaking; 
                                        and
                                            ``(cc) shall be made 
                                        publicly available in a manner 
                                        that does not reveal 
                                        manufacturer identity or 
                                        confidential business 
                                        information, in a timely manner 
                                        for discussion at any public 
                                        proceeding at which comment is 
                                        solicited from the public in 
                                        connection with the rulemaking, 
                                        except that nothing in this 
                                        subclause restricts the 
                                        Secretary from seeking 
                                        additional information during 
                                        the course of the rulemaking; 
                                        and
                                    ``(III) phased-in effective dates 
                                for different types of pole-mounted 
                                outdoor luminaires that are submitted 
                                to the Secretary in the manner provided 
                                for in section 325(p)(4), except that 
                                the phased-in effective dates shall not 
                                be subject to subparagraphs (A) and (B) 
                                of this paragraph.
            ``(4) Rulemaking before february 1, 2015.--
                    ``(A) In general.--Not later than February 1, 2015, 
                the Secretary shall initiate a rulemaking procedure to 
                determine whether the standards in effect for pole-
                mounted outdoor luminaires should be amended.
                    ``(B) Final rule.--
                            ``(i) Publication.--The Secretary shall 
                        publish a final rule containing the amendments, 
                        if any, not later than January 1, 2018.
                            ``(ii) Application.--Any amendments shall 
                        apply to products manufactured on or after 
                        January 1, 2021.
                    ``(C) Review.--
                            ``(i) In general.--As part of the 
                        rulemaking required under this paragraph, the 
                        Secretary shall review and may amend the 
                        definitions, exclusions, test procedures, power 
                        factor standards, lumen maintenance 
                        requirements, labeling requirements, and 
                        additional control requirements, including 
                        dimming functionality, for all pole-mounted 
                        outdoor luminaires.
                            ``(ii) Factors.--The review of the 
                        Secretary shall include consideration of--
                                    ``(I) obstacles to compliance and 
                                whether compliance is evaded by 
                                substitution of nonregulated luminaires 
                                for regulated luminaires or allowing 
                                luminaires to comply with the standards 
                                established under this part based on 
                                use of nonstandard lamps, as provided 
                                for in section 343(a)(10)(D)(i)(II);
                                    ``(II) statistical data relating to 
                                pole-mounted outdoor luminaires that--
                                            ``(aa) the Secretary 
                                        considers necessary for the 
                                        rulemaking and requests not 
                                        later than June 1, 2015, from 
                                        all identifiable manufacturers 
                                        of pole-mounted outdoor 
                                        luminaires, directly from 
                                        manufacturers of pole-mounted 
                                        outdoor luminaires and, in the 
                                        case of members of the National 
                                        Electrical Manufacturers 
                                        Association, from the National 
                                        Electrical Manufacturers 
                                        Association; and
                                            ``(bb) shall be made 
                                        publicly available in a manner 
                                        that does not reveal 
                                        manufacturer identity or 
                                        confidential business 
                                        information, in a timely manner 
                                        for discussion at any public 
                                        proceeding at which comment is 
                                        solicited from the public in 
                                        connection with the rulemaking, 
                                        except that nothing in this 
                                        subclause restricts the 
                                        Secretary from seeking 
                                        additional information during 
                                        the course of the rulemaking; 
                                        and
                                    ``(III) phased-in effective dates 
                                for different types of pole-mounted 
                                outdoor luminaires that are submitted 
                                to the Secretary in the manner provided 
                                for in section 325(p)(4), except that 
                                the phased-in effective dates shall not 
                                be subject to subparagraphs (A) and (B) 
                                of this paragraph.
    ``(h) High Light Output Double-Ended Quartz Halogen Lamps.--A high 
light output double-ended quartz halogen lamp manufactured on or after 
January 1, 2016, shall have a minimum efficiency of--
            ``(1) 27 LPW for lamps with a minimum rated initial lumen 
        value greater than 6,000 and a maximum initial lumen value of 
        15,000; and
            ``(2) 34 LPW for lamps with a rated initial lumen value 
        greater than 15,000 and less than 40,000.
    ``(i) General Purpose Mercury Vapor Lamps.--A general purpose 
mercury vapor lamp shall not be manufactured on or after January 1, 
2016.''.
    (c) Test Methods.--Section 343(a) of the Energy Policy and 
Conservation Act (42 U.S.C. 6314(a)) is amended by adding at the end 
the following:
            ``(10) Pole-mounted outdoor luminaires.--
                    ``(A) In general.--With respect to pole-mounted 
                outdoor luminaires to which standards are applicable 
                under section 342, the test methods shall be those 
                described in this paragraph.
                    ``(B) Photometric test methods.--For photometric 
                test methods, the methods shall be those specified in--
                            ``(i) IES LM-10-96--Approved Method for 
                        Photometric Testing of Outdoor Fluorescent 
                        Luminaires;
                            ``(ii) IES LM-31-95--Photometric Testing of 
                        Roadway Luminaires Using Incandescent Filament 
                        and High Intensity Discharge Lamps;
                            ``(iii) IES LM-79-08--Electrical and 
                        Photometric Measurements of Solid-State 
                        Lighting Products;
                            ``(iv) IES LM-80-08--Measuring Lumen 
                        Maintenance of LED Light Sources;
                            ``(v) IES LM-40-01--Life testing of 
                        Fluorescent Lamps;
                            ``(vi) IES LM-47-01--Life testing of High 
                        Intensity Discharge (HID) Lamps;
                            ``(vii) IES LM-49-01--Life testing of 
                        Incandescent Filament Lamps;
                            ``(viii) IES LM-60-01--Life testing of Low 
                        Pressure Sodium Lamps; and
                            ``(ix) IES LM-65-01--Life testing of 
                        Compact Fluorescent Lamps.
                    ``(C) Outdoor backlight, uplight, and glare 
                ratings.--For determining outdoor backlight, uplight, 
                and glare ratings, the classifications shall be those 
                specified in IES TM-15-07--Luminaire Classification 
                System for Outdoor Luminaires with Addendum A.
                    ``(D) Target efficacy rating.--For determining the 
                target efficacy rating, the procedures shall be those 
                specified in NEMA LE-6-2009--`Procedure for Determining 
                Target Efficacy Ratings (TER) for Commercial, 
                Industrial and Residential Luminaires,' and all of the 
                following additional criteria (as applicable):
                            ``(i) The target efficacy rating shall be 
                        calculated based on the initial rated lamp 
                        lumen and rated watt value equivalent to the 
                        lamp with which the luminaire is shipped, or, 
                        if not shipped with a lamp, the target efficacy 
                        rating shall be calculated based on--
                                    ``(I) the applicable standard lamp 
                                as established by subparagraph (E); or
                                    ``(II) a lamp that has a rated 
                                wattage and rated initial lamp lumens 
                                that are the same as the maximum lamp 
                                watts and minimum lamp lumens labeled 
                                on the luminaire, in accordance with 
                                section 344(f).
                            ``(ii) If the luminaire is designed to 
                        operate at more than 1 nominal input voltage, 
                        the ballast input watts used in the target 
                        efficacy rating calculation shall be the 
                        highest value for any nominal input voltage for 
                        which the ballast is designed to operate.
                            ``(iii) If the luminaire is a pole-mounted 
                        outdoor luminaire that contains a ballast that 
                        is labeled to operate lamps of more than 1 
                        wattage, the luminaire shall--
                                    ``(I) meet or exceed the target 
                                efficacy rating in the table in section 
                                342(g)(1)(B) calculated in accordance 
                                with clause (i) for all lamp wattages 
                                that the ballast is labeled to operate;
                                    ``(II) be constructed such that the 
                                luminaire is only capable of accepting 
                                lamp wattages that produce target 
                                efficacy ratings that meet or exceed 
                                the values in the table in section 
                                342(g)(1)(B) calculated in accordance 
                                with clause (i); or
                                    ``(III) be rated and prominently 
                                labeled for a maximum lamp wattage that 
                                results in the luminaire meeting or 
                                exceeding the target efficacy rating in 
                                the table in section 342(g)(1)(B) when 
                                calculated and labeled in accordance 
                                with clause (i).
                            ``(iv) If the luminaire is a pole-mounted 
                        outdoor luminaire that is constructed such that 
                        the luminaire will only accept an ANSI Type-O 
                        lamp, the luminaire shall meet or exceed the 
                        target efficacy rating in the table in section 
                        342(g)(1)(B) when tested with an ANSI Type-O 
                        lamp.
                            ``(v) If the luminaire is a pole-mounted 
                        outdoor luminaire that is marketed to use a 
                        coated lamp, the luminaire shall meet or exceed 
                        the target efficacy rating in the table in 
                        section 342(g)(1)(B) when tested with a coated 
                        lamp.
                            ``(vi) If the luminaire is a solid state 
                        lighting pole-mounted outdoor luminaire, the 
                        luminaire shall have its target efficacy rating 
                        calculated based on the combination of absolute 
                        luminaire lumen values and input wattages that 
                        results in the lowest possible target efficacy 
                        rating for any light source, including ranges 
                        of correlated color temperature and color 
                        rendering index values, for which the luminaire 
                        is marketed by the luminaire manufacturer.
                            ``(vii) If the luminaire is a high 
                        intensity discharge pole-mounted outdoor 
                        luminaire using a ballast that has a ballast 
                        factor different than 1, the target efficacy 
                        rating of the luminaire shall be calculated by 
                        using the input watts needed to operate the 
                        lamp at full rated power, or by using the 
                        actual ballast factor of the ballast.
                    ``(E) Table of standard lamp types.--
                            ``(i) In general.--The National Electrical 
                        Manufacturers Association shall develop and 
                        publish not later than 1 year after the date of 
                        enactment of this paragraph and thereafter 
                        maintain and regularly update on a publicly 
                        available website a table including standard 
                        lamp types by wattage, ANSI code, initial lamp 
                        lumen value, lamp orientation, and lamp finish.
                            ``(ii) Initial lamp lumen values.--The 
                        initial lamp lumen values shall--
                                    ``(I) be determined according to a 
                                uniform rating method and tested 
                                according to accepted industry practice 
                                for each lamp that is considered for 
                                inclusion in the table; and
                                    ``(II) in each case contained in 
                                the table, be the lowest known initial 
                                lamp lumen value that approximates 
                                typical performance in representative 
                                general outdoor lighting applications.
                            ``(iii) Actions.--On completion of the 
                        table required by this subparagraph and any 
                        updates to the table--
                                    ``(I) the National Electrical 
                                Manufacturers Association shall submit 
                                the table and any updates to the 
                                Secretary; and
                                    ``(II) the Secretary shall--
                                            ``(aa) publish the table 
                                        and any comments that are 
                                        included with the table in the 
                                        Federal Register;
                                            ``(bb) solicit public 
                                        comment on the table; and
                                            ``(cc) not later than 180 
                                        days after date of receipt of 
                                        the table, after considering 
                                        the factors described in clause 
                                        (iv), adopt the table for 
                                        purposes of this part.
                            ``(iv) Rebuttable presumption.--
                                    ``(I) In general.--There shall be a 
                                rebuttable presumption that the table 
                                and any updates to the table 
                                transmitted by the National Electrical 
                                Manufacturers Association to the 
                                Secretary meets the requirements of 
                                this subparagraph, which may be 
                                rebutted only if the Secretary finds by 
                                clear and substantial evidence that--
                                            ``(aa) data have been 
                                        included that were not the 
                                        result of having applied 
                                        applicable industry standards; 
                                        or
                                            ``(bb) lamps have been 
                                        included in the table that are 
                                        not representative of general 
                                        outdoor lighting applications.
                                    ``(II) Conforming changes.--If 
                                subclause (I) applies, the National 
                                Electrical Manufacturers Association 
                                shall conform the published table of 
                                the Association to the table adopted by 
                                the Secretary.
                            ``(v) Nontransmission of table.--If the 
                        National Electrical Manufacturers Association 
                        has not submitted the table to the Secretary 
                        within 1 year after the date of enactment of 
                        this paragraph, the Secretary shall develop, 
                        publish, and adopt the table not later than 18 
                        months after the date of enactment of this 
                        paragraph and update the table regularly.
                    ``(F) Amendment of test methods.--The Secretary 
                may, by rule, adopt new or additional test methods for 
                pole-mounted outdoor luminaires in accordance with this 
                section.''.
    (d) Labeling.--Section 344 of the Energy Policy and Conservation 
Act (42 U.S.C. 6315) is amended--
            (1) in subsections (d) and (e), by striking ``(h)'' each 
        place it appears and inserting ``(i)'';
            (2) by redesignating subsections (f) through (k) as 
        subsections (g) through (l), respectively; and
            (3) by inserting after subsection (e) the following:
    ``(f) Labeling Rules for Pole-Mounted Outdoor Luminaires.--
            ``(1) In general.--Subject to subsection (i), not later 
        than 1 year after the date of enactment of this paragraph, the 
        Secretary shall establish labeling rules under this part for 
        pole-mounted outdoor luminaires manufactured on or after the 
        date on which standards established under section 342(g) take 
        effect.
            ``(2) Rules.--The rules shall require--
                    ``(A) for pole-mounted outdoor luminaires, that the 
                luminaire, be marked with a capital letter `P' printed 
                within a circle in a conspicuous location on both the 
                pole-mounted luminaire and its packaging to indicate 
                that the pole-mounted outdoor luminaire conforms to the 
                energy conservation standards established in section 
                342(g); and
                    ``(B) for pole-mounted outdoor luminaires that do 
                not contain a lamp in the same shipment with the 
                luminaire and are tested with a lamp with a lumen 
                rating exceeding the standard lumen value specified in 
                the table established under section 343(a)(10)(E), that 
                the luminaire--
                            ``(i) be labeled to identify the minimum 
                        rated initial lamp lumens and maximum rated 
                        lamp watts required to conform to the energy 
                        conservation standards established in section 
                        342(g); and
                            ``(ii) bear a statement on the label that 
                        states: `Product violates Federal law when 
                        installed with a standard lamp. Use only a lamp 
                        that meets the minimum lumens and maximum watts 
                        provided on this label.'.''.
    (e) Preemption.--Section 345 of the Energy Policy and Conservation 
Act (42 U.S.C. 6316) is amended--
            (1) in the first sentence of subsection (a), by striking 
        ``The'' and inserting ``Except as otherwise provided in this 
        section, the''; and
            (2) by adding at the end the following:
    ``(i) Pole-Mounted Outdoor Luminaires and High Light Output Double-
Ended Quartz Halogen Lamps.--
            ``(1) In general.--Except as provided in paragraph (2), 
        section 327 shall apply to pole-mounted outdoor luminaires and 
        high light output double-ended quartz halogen lamps to the same 
        extent and in the same manner as the section applies under part 
        B.
            ``(2) State energy conservation standards.--Any State 
        energy conservation standard that is adopted on or before 
        January 1, 2015, pursuant to a statutory requirement to adopt 
        efficiency standard for reducing outdoor lighting energy use 
        enacted prior to January 31, 2008, shall not be preempted.''.

SEC. 23. STANDARDS FOR COMMERCIAL FURNACES.

    Section 342(a) of the Energy Policy and Conservation Act (42 U.S.C. 
6313(a)) is amended by adding at the end the following:
            ``(11) Warm air furnaces with an input rating of 225,000 
        Btu per hour or more and manufactured after January 1, 2011, 
        shall meet the following standard levels:
                    ``(A) Gas-fired units shall--
                            ``(i) have a minimum combustion efficiency 
                        of 80 percent;
                            ``(ii) include an interrupted or 
                        intermittent ignition device;
                            ``(iii) have jacket losses not exceeding 
                        0.75 percent of the input rating; and
                            ``(iv) have power venting or a flue damper.
                    ``(B) Oil-fired units shall have--
                            ``(i) a minimum thermal efficiency of 81 
                        percent;
                            ``(ii) jacket losses not exceeding 0.75 
                        percent of the input rating; and
                            ``(iii) power venting or a flue damper.''.

SEC. 24. SERVICE OVER THE COUNTER, SELF-CONTAINED, MEDIUM TEMPERATURE 
              COMMERCIAL REFRIGERATORS.

    Section 342(c) of the Energy Policy and Conservation Act (42 U.S.C. 
6313(c)) is amended--
            (1) in paragraph (1)--
                    (A) by redesignating subparagraph (C) as 
                subparagraph (E); and
                    (B) by inserting after subparagraph (B) the 
                following:
                    ``(C) The term `service over the counter, self-
                contained, medium temperature commercial refrigerator' 
                or `(SOC-SC-M)' means a medium temperature commercial 
                refrigerator--
                            ``(i) with a self-contained condensing unit 
                        and equipped with sliding or hinged doors in 
                        the back intended for use by sales personnel, 
                        and with glass or other transparent material in 
                        the front for displaying merchandise; and
                            ``(ii) that has a height not greater than 
                        66 inches and is intended to serve as a counter 
                        for transactions between sales personnel and 
                        customers.
                    ``(D) The term `TDA' means the total display area 
                (ft\2\) of the refrigerated case, as defined in AHRI 
                Standard 1200.'';
            (2) by redesignating paragraphs (4) and (5) as paragraphs 
        (5) and (6), respectively; and
            (3) by inserting after paragraph (3) the following:
            ``(4) Each SOC-SC-M manufactured on or after January 1, 
        2012, shall have a total daily energy consumption (in kilowatt 
        hours per day) of not more than 0.6 x TDA + 1.0.''.

SEC. 25. MOTOR MARKET ASSESSMENT AND COMMERCIAL AWARENESS PROGRAM.

    (a) Findings.--Congress finds that--
            (1) electric motor systems account for about half of the 
        electricity used in the United States;
            (2) electric motor energy use is determined by both the 
        efficiency of the motor and the system in which the motor 
        operates;
            (3) Federal Government research on motor end use and 
        efficiency opportunities is more than a decade old; and
            (4) the Census Bureau has discontinued collection of data 
        on motor and generator importation, manufacture, shipment, and 
        sales.
    (b) Definitions.--In this section:
            (1) Department.--The term ``Department'' means the 
        Department of Energy.
            (2) Interested parties.--The term ``interested parties'' 
        includes--
                    (A) trade associations;
                    (B) motor manufacturers;
                    (C) motor end users;
                    (D) electric utilities; and
                    (E) individuals and entities that conduct energy 
                efficiency programs.
            (3) Secretary.--The term ``Secretary'' means the Secretary 
        of Energy, in consultation with interested parties.
    (c) Assessment.--The Secretary shall conduct an assessment of 
electric motors and the electric motor market in the United States that 
shall--
            (1) include important subsectors of the industrial and 
        commercial electric motor market (as determined by the 
        Secretary), including--
                    (A) the stock of motors and motor-driven equipment;
                    (B) efficiency categories of the motor population; 
                and
                    (C) motor systems that use drives, servos, and 
                other control technologies;
            (2) characterize and estimate the opportunities for 
        improvement in the energy efficiency of motor systems by market 
        segment, including opportunities for--
                    (A) expanded use of drives, servos, and other 
                control technologies;
                    (B) expanded use of process control, pumps, 
                compressors, fans or blowers, and material handling 
                components; and
                    (C) substitution of existing motor designs with 
                existing and future advanced motor designs, including 
                electronically commutated permanent magnet, interior 
                permanent magnet, and switched reluctance motors; and
            (3) develop an updated profile of motor system purchase and 
        maintenance practices, including surveying the number of 
        companies that have motor purchase and repair specifications, 
        by company size, number of employees, and sales.
    (d) Recommendations; Update.--Based on the assessment conducted 
under subsection (c), the Secretary shall--
            (1) develop--
                    (A) recommendations to update the detailed motor 
                profile on a periodic basis;
                    (B) methods to estimate the energy savings and 
                market penetration that is attributable to the Save 
                Energy Now Program of the Department; and
                    (C) recommendations for the Director of the Census 
                Bureau on market surveys that should be undertaken in 
                support of the motor system activities of the 
                Department; and
            (2) prepare an update to the Motor Master+ program of the 
        Department.
    (e) Program.--Based on the assessment, recommendations, and update 
required under subsections (c) and (d), the Secretary shall establish a 
proactive, national program targeted at motor end-users and delivered 
in cooperation with interested parties to increase awareness of--
            (1) the energy and cost-saving opportunities in commercial 
        and industrial facilities using higher efficiency electric 
        motors;
            (2) improvements in motor system procurement and management 
        procedures in the selection of higher efficiency electric 
        motors and motor-system components, including drives, controls, 
        and driven equipment; and
            (3) criteria for making decisions for new, replacement, or 
        repair motor and motor system components.

SEC. 26. STUDY OF COMPLIANCE WITH ENERGY STANDARDS FOR APPLIANCES.

    (a) In General.--The Secretary shall conduct a study of the degree 
of compliance with energy standards for appliances, including an 
investigation of compliance rates and options for improving compliance, 
including enforcement.
    (b) Report.--Not later than 18 months after the date of enactment 
of this Act, the Secretary shall submit to the appropriate committees 
of Congress a report describing the results of the study, including any 
recommendations.

SEC. 27. STUDY OF DIRECT CURRENT ELECTRICITY SUPPLY IN CERTAIN 
              BUILDINGS.

    (a) In General.--The Secretary shall conduct a study--
            (1) of the costs and benefits (including significant energy 
        efficiency, power quality, and other power grid, safety, and 
        environmental benefits) of requiring high-quality, direct 
        current electricity supply in certain buildings; and
            (2) to determine, if the requirement described in paragraph 
        (1) is imposed, what the policy and role of the Federal 
        Government should be in realizing those benefits.
    (b) Report.--Not later than 1 year after the date of enactment of 
this Act, the Secretary shall submit to the appropriate committees of 
Congress a report describing the results of the study, including any 
recommendations.

SEC. 28. TECHNICAL CORRECTIONS.

    (a) Title III of Energy Independence and Security Act of 2007--
Energy Savings Through Improved Standards for Appliances and 
Lighting.--
            (1) Section 325(u) of the Energy Policy and Conservation 
        Act (42 U.S.C. 6295(u)) (as amended by section 301(c) of the 
        Energy Independence and Security Act of 2007 (121 Stat. 1550)) 
        is amended--
                    (A) by redesignating paragraph (7) as paragraph 
                (4); and
                    (B) in paragraph (4) (as so redesignated), by 
                striking ``supplies is'' and inserting ``supply is''.
            (2) Section 302(b) of the Energy Independence and Security 
        Act of 2007 (121 Stat. 1551) is amended by striking ``6313(a)'' 
        and inserting ``6314(a)''.
            (3) Section 342(a)(6) of the Energy Policy and Conservation 
        Act (42 U.S.C. 6313(a)(6)) (as amended by section 305(b)(2) of 
        the Energy Independence and Security Act of 2007 (121 Stat. 
        1554)) is amended--
                    (A) in subparagraph (B)--
                            (i) by striking ``If the Secretary'' and 
                        inserting the following:
                            ``(i) In general.--If the Secretary'';
                            (ii) by striking ``clause (ii)(II)'' and 
                        inserting ``subparagraph (A)(ii)(II)'';
                            (iii) by striking ``clause (i)'' and 
                        inserting ``subparagraph (A)(i)''; and
                            (iv) by adding at the end the following:
                            ``(ii) Factors.--In determining whether a 
                        standard is economically justified for the 
                        purposes of subparagraph (A)(ii)(II), the 
                        Secretary shall, after receiving views and 
                        comments furnished with respect to the proposed 
                        standard, determine whether the benefits of the 
                        standard exceed the burden of the proposed 
                        standard by, to the maximum extent practicable, 
                        considering--
                                    ``(I) the economic impact of the 
                                standard on the manufacturers and on 
                                the consumers of the products subject 
                                to the standard;
                                    ``(II) the savings in operating 
                                costs throughout the estimated average 
                                life of the product in the type (or 
                                class) compared to any increase in the 
                                price of, or in the initial charges 
                                for, or maintenance expenses of, the 
                                products that are likely to result from 
                                the imposition of the standard;
                                    ``(III) the total projected 
                                quantity of energy savings likely to 
                                result directly from the imposition of 
                                the standard;
                                    ``(IV) any lessening of the utility 
                                or the performance of the products 
                                likely to result from the imposition of 
                                the standard;
                                    ``(V) the impact of any lessening 
                                of competition, as determined in 
                                writing by the Attorney General, that 
                                is likely to result from the imposition 
                                of the standard;
                                    ``(VI) the need for national energy 
                                conservation; and
                                    ``(VII) other factors the Secretary 
                                considers relevant.
                            ``(iii) Administration.--
                                    ``(I) Energy use and efficiency.--
                                The Secretary may not prescribe any 
                                amended standard under this paragraph 
                                that increases the maximum allowable 
                                energy use, or decreases the minimum 
                                required energy efficiency, of a 
                                covered product.
                                    ``(II) Unavailability.--
                                            ``(aa) In general.--The 
                                        Secretary may not prescribe an 
                                        amended standard under this 
                                        subparagraph if the Secretary 
                                        finds (and publishes the 
                                        finding) that interested 
                                        persons have established by a 
                                        preponderance of the evidence 
                                        that a standard is likely to 
                                        result in the unavailability in 
                                        the United States in any 
                                        product type (or class) of 
                                        performance characteristics 
                                        (including reliability, 
                                        features, sizes, capacities, 
                                        and volumes) that are 
                                        substantially the same as those 
                                        generally available in the 
                                        United States at the time of 
                                        the finding of the Secretary.
                                            ``(bb) Other types or 
                                        classes.--The failure of some 
                                        types (or classes) to meet the 
                                        criterion established under 
                                        this subclause shall not affect 
                                        the determination of the 
                                        Secretary on whether to 
                                        prescribe a standard for the 
                                        other types or classes.''; and
                    (B) in subparagraph (C)(iv), by striking ``An 
                amendment prescribed under this subsection'' and 
                inserting ``Notwithstanding subparagraph (D), an 
                amendment prescribed under this subparagraph''.
            (4) Section 342(a)(6)(B)(iii) of the Energy Policy and 
        Conservation Act (as added by section 306(c) of the Energy 
        Independence and Security Act of 2007 (121 Stat. 1559)) is 
        transferred and redesignated as clause (vi) of section 
        342(a)(6)(C) of the Energy Policy and Conservation Act (as 
        amended by section 305(b)(2) of the Energy Independence and 
        Security Act of 2007 (121 Stat. 1554)).
            (5) Section 345 of the Energy Policy and Conservation Act 
        (42 U.S.C. 6316) (as amended by section 312(e) of the Energy 
        Independence and Security Act of 2007 (121 Stat. 1567)) is 
        amended--
                    (A) by striking ``subparagraphs (B) through (G)'' 
                each place it appears and inserting ``subparagraphs 
                (B), (C), (D), (I), (J), and (K)'';
                    (B) by striking ``part A'' each place it appears 
                and inserting ``part B''; and
                    (C) in subsection (h)(3), by striking ``section 
                342(f)(3)'' and inserting ``section 342(f)(4)''.
            (6) Section 340(13) of the Energy Policy and Conservation 
        Act (42 U.S.C. 6311(13)) (as amended by section 313(a) of the 
        Energy Independence and Security Act of 2007 (121 Stat. 1568)) 
        is amended--
                    (A) by striking subparagraphs (A) and (B) and 
                inserting the following:
                    ``(A) In general.--The term `electric motor' means 
                any of the following:
                            ``(i) A motor that is a general purpose T-
                        frame, single-speed, foot-mounting, polyphase 
                        squirrel-cage induction motor of the National 
                        Electrical Manufacturers Association, Design A 
                        and B, continuous rated, operating on 230/460 
                        volts and constant 60 Hertz line power as 
                        defined in NEMA Standards Publication MG1-1987.
                            ``(ii) A motor incorporating the design 
                        elements described in clause (i), but is 
                        configured to incorporate 1 or more of the 
                        following variations:
                                    ``(I) U-frame motor.
                                    ``(II) NEMA Design C motor.
                                    ``(III) Close-coupled pump motor.
                                    ``(IV) Footless motor.
                                    ``(V) Vertical solid shaft normal 
                                thrust motor (as tested in a horizontal 
                                configuration).
                                    ``(VI) 8-pole motor.
                                    ``(VII) Poly-phase motor with a 
                                voltage rating of not more than 600 
                                volts (other than 230 volts or 460 
                                volts, or both, or can be operated on 
                                230 volts or 460 volts, or both).''; 
                                and
                    (B) by redesignating subparagraphs (C) through (I) 
                as subparagraphs (B) through (H), respectively.
            (7)(A) Section 342(b) of the Energy Policy and Conservation 
        Act (42 U.S.C. 6313(b)) is amended--
                    (i) in paragraph (1), by striking ``paragraph (2)'' 
                and inserting ``paragraph (3)'';
                    (ii) by redesignating paragraphs (2) and (3) as 
                paragraphs (3) and (4);
                    (iii) by inserting after paragraph (1) the 
                following:
            ``(2) Standards effective beginning december 19, 2010.--
                    ``(A) In general.--Except for definite purpose 
                motors, special purpose motors, and those motors 
                exempted by the Secretary under paragraph (3) and 
                except as provided for in subparagraphs (B), (C), and 
                (D), each electric motor manufactured with power 
                ratings from 1 to 200 horsepower (alone or as a 
                component of another piece of equipment) on or after 
                December 19, 2010, shall have a nominal full load 
                efficiency of not less than the nominal full load 
                efficiency described in NEMA MG-1 (2006) Table 12-12.
                    ``(B) Fire pump electric motors.--Except for those 
                motors exempted by the Secretary under paragraph (3), 
                each fire pump electric motor manufactured with power 
                ratings from 1 to 200 horsepower (alone or as a 
                component of another piece of equipment) on or after 
                December 19, 2010, shall have a nominal full load 
                efficiency that is not less than the nominal full load 
                efficiency described in NEMA MG-1 (2006) Table 12-11.
                    ``(C) NEMA design b electric motors.--Except for 
                those motors exempted by the Secretary under paragraph 
                (3), each NEMA Design B electric motor with power 
                ratings of more than 200 horsepower, but not greater 
                than 500 horsepower, manufactured (alone or as a 
                component of another piece of equipment) on or after 
                December 19, 2010, shall have a nominal full load 
                efficiency of not less than the nominal full load 
                efficiency described in NEMA MG-1 (2006) Table 12-11.
                    ``(D) Motors incorporating certain design 
                elements.--Except for those motors exempted by the 
                Secretary under paragraph (3), each electric motor 
                described in section 340(13)(A)(ii) manufactured with 
                power ratings from 1 to 200 horsepower (alone or as a 
                component of another piece of equipment) on or after 
                December 19, 2010, shall have a nominal full load 
                efficiency of not less than the nominal full load 
                efficiency described in NEMA MG-1 (2006) Table 12-
                11.''; and
                    (iv) in paragraph (3) (as redesignated by clause 
                (ii)), by striking ``paragraph (1)'' each place it 
                appears in subparagraphs (A) and (D) and inserting 
                ``paragraphs (1) and (2)''.
            (B) Section 313 of the Energy Independence and Security Act 
        of 2007 (121 Stat. 1568) is repealed.
            (C) The amendments made by--
                    (i) subparagraph (A) take effect on December 19, 
                2010; and
                    (ii) subparagraph (B) take effect on December 19, 
                2007.
            (8) Section 321(30)(D)(i)(III) of the Energy Policy and 
        Conservation Act (42 U.S.C. 6291(30)(D)(i)(III)) (as amended by 
        section 321(a)(1)(A) of the Energy Independence and Security 
        Act of 2007 (121 Stat. 1574)) is amended by inserting before 
        the semicolon the following: ``or, in the case of a modified 
        spectrum lamp, not less than 232 lumens and not more than 1,950 
        lumens''.
            (9) Section 321(30)(T) of the Energy Policy and 
        Conservation Act (42 U.S.C. 6291(30)(T)) (as amended by section 
        321(a)(1)(B) of the Energy Independence and Security Act of 
        2007 (121 Stat. 1574)) is amended--
                    (A) in clause (i)--
                            (i) by striking the comma after ``household 
                        appliance'' and inserting ``and''; and
                            (ii) by striking ``and is sold at 
                        retail,''; and
                    (B) in clause (ii), by inserting ``when sold at 
                retail,'' before ``is designated''.
            (10) Section 325(i) of the Energy Policy and Conservation 
        Act (42 U.S.C. 6295(i)) (as amended by sections 321(a)(3)(A) 
        and 322(b) of the Energy Independence and Security Act of 2007 
        (121 Stat. 1577, 1588)) is amended by striking the subsection 
        designation and all that follows through the end of paragraph 
        (8) and inserting the following:
    ``(i) General Service Fluorescent Lamps, General Service 
Incandescent Lamps, Intermediate Base Incandescent Lamps, Candelabra 
Base Incandescent Lamps, and Incandescent Reflector Lamps.--
            ``(1) Energy efficiency standards.--
                    ``(A) In general.--Each of the following general 
                service fluorescent lamps, general service incandescent 
                lamps, intermediate base incandescent lamps, candelabra 
                base incandescent lamps, and incandescent reflector 
                lamps manufactured after the effective date specified 
                in the tables listed in this subparagraph shall meet or 
                exceed the standards established in the following 
                tables:


                                               ``FLUORESCENT LAMPS
----------------------------------------------------------------------------------------------------------------
                                                                                                  Effective Date
           Lamp Type               Nominal Lamp       Minimum CRI       Minimum Average Lamp        (Period of
                                      Wattage                              Efficacy (LPW)            Months)
----------------------------------------------------------------------------------------------------------------
4-foot medium bi-pin...........        >35 W              69                    75.0                    36
                                       35 W               45                    75.0                    36
2-foot U-shaped................        >35 W              69                    68.0                    36
                                        35 W              45                    64.0                    36
8-foot slimline................        >65 W              69                    80.0                    18
                                       65 W               45                    80.0                    18
8-foot high output.............       >100 W              69                    80.0                    18
                                       100 W              45                    80.0                    18
----------------------------------------------------------------------------------------------------------------


                     ``INCANDESCENT REFLECTOR LAMPS
------------------------------------------------------------------------
                                                          Effective Date
     Nominal Lamp Wattage         Minimum Average Lamp      (Period of
                                     Efficacy (LPW)           Months)
------------------------------------------------------------------------
 40-50.......................             10.5                  36
 51-66.......................             11.0                  36
 67-85.......................             12.5                  36
 86-115......................             14.0                  36
116-155......................             14.5                  36
156-205......................             15.0                  36
------------------------------------------------------------------------



                                      ``GENERAL SERVICE INCANDESCENT LAMPS
----------------------------------------------------------------------------------------------------------------
                                                                                         Minimum
                       Rated Lumen Ranges                            Maximum Rated        Rated       Effective
                                                                        Wattage         Lifetime        Date
----------------------------------------------------------------------------------------------------------------
1490-2600                                                                        72     1,000 hrs      1/1/2012
1050-1489                                                                        53     1,000 hrs      1/1/2013
750-1049                                                                         43     1,000 hrs      1/1/2014
310-749                                                                          29     1,000 hrs      1/1/2014
----------------------------------------------------------------------------------------------------------------



                             ``MODIFIED SPECTRUM GENERAL SERVICE INCANDESCENT LAMPS
----------------------------------------------------------------------------------------------------------------
                                                                                         Minimum
                       Rated Lumen Ranges                            Maximum Rated        Rated       Effective
                                                                        Wattage         Lifetime        Date
----------------------------------------------------------------------------------------------------------------
1118-1950                                                                        72     1,000 hrs      1/1/2012
788-1117                                                                         53     1,000 hrs      1/1/2013
563-787                                                                          43     1,000 hrs      1/1/2014
232-562                                                                          29     1,000 hrs      1/1/2014
----------------------------------------------------------------------------------------------------------------

                    ``(B) Application.--
                            ``(i) Application criteria.--This 
                        subparagraph applies to each lamp that--
                                    ``(I) is intended for a general 
                                service or general illumination 
                                application (whether incandescent or 
                                not);
                                    ``(II) has a medium screw base or 
                                any other screw base not defined in 
                                ANSI C81.61-2006;
                                    ``(III) is capable of being 
                                operated at a voltage at least 
                                partially within the range of 110 to 
                                130 volts; and
                                    ``(IV) is manufactured or imported 
                                after December 31, 2011.
                            ``(ii) Requirement.--For purposes of this 
                        paragraph, each lamp described in clause (i) 
                        shall have a color rendering index that is 
                        greater than or equal to--
                                    ``(I) 80 for nonmodified spectrum 
                                lamps; or
                                    ``(II) 75 for modified spectrum 
                                lamps.
                    ``(C) Candelabra incandescent lamps and 
                intermediate base incandescent lamps.--
                            ``(i) Candelabra base incandescent lamps.--
                        Effective beginning January 1, 2012, a 
                        candelabra base incandescent lamp shall not 
                        exceed 60 rated watts.
                            ``(ii) Intermediate base incandescent 
                        lamps.--Effective beginning January 1, 2012, an 
                        intermediate base incandescent lamp shall not 
                        exceed 40 rated watts.
                    ``(D) Exemptions.--
                            ``(i) Statutory exemptions.--The standards 
                        specified in subparagraph (A) shall not apply 
                        to the following types of incandescent 
                        reflector lamps:
                                    ``(I) Lamps rated at 50 watts or 
                                less that are ER30, BR30, BR40, or ER40 
                                lamps.
                                    ``(II) Lamps rated at 65 watts that 
                                are BR30, BR40, or ER40 lamps.
                                    ``(III) R20 incandescent reflector 
                                lamps rated 45 watts or less.
                            ``(ii) Administrative exemptions.--
                                    ``(I) Petition.--Any person may 
                                petition the Secretary for an exemption 
                                for a type of general service lamp from 
                                the requirements of this subsection.
                                    ``(II) Criteria.--The Secretary may 
                                grant an exemption under subclause (I) 
                                only to the extent that the Secretary 
                                finds, after a hearing and opportunity 
                                for public comment, that it is not 
                                technically feasible to serve a 
                                specialized lighting application (such 
                                as a military, medical, public safety, 
                                or certified historic lighting 
                                application) using a lamp that meets 
                                the requirements of this subsection.
                                    ``(III) Additional criterion.--To 
                                grant an exemption for a product under 
                                this clause , the Secretary shall 
                                include, as an additional criterion, 
                                that the exempted product is unlikely 
                                to be used in a general service 
                                lighting application.
                    ``(E) Extension of coverage.--
                            ``(i) Petition.--Any person may petition 
                        the Secretary to establish standards for lamp 
                        shapes or bases that are excluded from the 
                        definition of general service lamps.
                            ``(ii) Increased sales of exempted lamps.--
                        The petition shall include evidence that the 
                        availability or sales of exempted incandescent 
                        lamps have increased significantly since the 
                        date on which the standards on general service 
                        incandescent lamps were established.
                            ``(iii) Criteria.--The Secretary shall 
                        grant a petition under clause (i) if the 
                        Secretary finds that--
                                    ``(I) the petition presents 
                                evidence that demonstrates that 
                                commercial availability or sales of 
                                exempted incandescent lamp types have 
                                increased significantly since the 
                                standards on general service lamps were 
                                established and likely are being widely 
                                used in general lighting applications; 
                                and
                                    ``(II) significant energy savings 
                                could be achieved by covering exempted 
                                products, as determined by the 
                                Secretary based in part on sales data 
                                provided to the Secretary from 
                                manufacturers and importers.
                            ``(iv) No presumption.--The grant of a 
                        petition under this subparagraph shall create 
                        no presumption with respect to the 
                        determination of the Secretary with respect to 
                        any criteria under a rulemaking conducted under 
                        this section.
                            ``(v) Expedited proceeding.--If the 
                        Secretary grants a petition for a lamp shape or 
                        base under this subparagraph, the Secretary 
                        shall--
                                    ``(I) conduct a rulemaking to 
                                determine standards for the exempted 
                                lamp shape or base; and
                                    ``(II) complete the rulemaking not 
                                later than 18 months after the date on 
                                which notice is provided granting the 
                                petition.
                    ``(F) Effective dates.--
                            ``(i) In general.--In this paragraph, 
                        except as otherwise provided in a table 
                        contained in subparagraph (A) or in clause 
                        (ii), the term `effective date' means the last 
                        day of the month specified in the table that 
                        follows October 24, 1992.
                            ``(ii) Special effective dates.--
                                    ``(I) ER, br, and bpar lamps.--The 
                                standards specified in subparagraph (A) 
                                shall apply with respect to ER 
                                incandescent reflector lamps, BR 
                                incandescent reflector lamps, BPAR 
                                incandescent reflector lamps, and 
                                similar bulb shapes on and after 
                                January 1, 2008, or the date that is 
                                180 days after the date of enactment of 
                                the Energy Independence and Security 
                                Act of 2007.
                                    ``(II) Lamps between 2.25-2.75 
                                inches in diameter.--The standards 
                                specified in subparagraph (A) shall 
                                apply with respect to incandescent 
                                reflector lamps with a diameter of more 
                                than 2.25 inches, but not more than 
                                2.75 inches, on and after the later of 
                                January 1, 2008, or the date that is 
                                180 days after the date of enactment of 
                                the Energy Independence and Security 
                                Act of 2007.
            ``(2) Compliance with existing law.--Notwithstanding 
        section 332(a)(5) and section 332(b), it shall not be unlawful 
        for a manufacturer to sell a lamp that is in compliance with 
        the law at the time the lamp was manufactured.
            ``(3) Rulemaking before october 24, 1995.--
                    ``(A) In general.--Not later than 36 months after 
                October 24, 1992, the Secretary shall initiate a 
                rulemaking procedure and shall publish a final rule not 
                later than the end of the 54-month period beginning on 
                October 24, 1992, to determine whether the standards 
                established under paragraph (1) should be amended.
                    ``(B) Administration.--The rule shall contain the 
                amendment, if any, and provide that the amendment shall 
                apply to products manufactured on or after the 36-month 
                period beginning on the date on which the final rule is 
                published.
            ``(4) Rulemaking before october 24, 2000.--
                    ``(A) In general.--Not later than 8 years after 
                October 24, 1992, the Secretary shall initiate a 
                rulemaking procedure and shall publish a final rule not 
                later than 9 years and 6 months after October 24, 1992, 
                to determine whether the standards in effect for 
                fluorescent lamps and incandescent lamps should be 
                amended.
                    ``(B) Administration.--The rule shall contain the 
                amendment, if any, and provide that the amendment shall 
                apply to products manufactured on or after the 36-month 
                period beginning on the date on which the final rule is 
                published.
            ``(5) Rulemaking for additional general service fluorescent 
        lamps.--
                    ``(A) In general.--Not later than the end of the 
                24-month period beginning on the date labeling 
                requirements under section 324(a)(2)(C) become 
                effective, the Secretary shall--
                            ``(i) initiate a rulemaking procedure to 
                        determine whether the standards in effect for 
                        fluorescent lamps and incandescent lamps should 
                        be amended so that the standards would be 
                        applicable to additional general service 
                        fluorescent lamps; and
                            ``(ii) publish, not later than 18 months 
                        after initiating the rulemaking, a final rule 
                        including the amended standards, if any.
                    ``(B) Administration.--The rule shall provide that 
                the amendment shall apply to products manufactured 
                after a date which is 36 months after the date on which 
                the rule is published.
            ``(6) Standards for general service lamps.--
                    ``(A) Rulemaking before january 1, 2014.--
                            ``(i) In general.--Not later than January 
                        1, 2014, the Secretary shall initiate a 
                        rulemaking procedure to determine whether--
                                    ``(I) standards in effect for 
                                general service lamps should be 
                                amended; and
                                    ``(II) the exclusions for certain 
                                incandescent lamps should be maintained 
                                or discontinued based, in part, on 
                                excluded lamp sales collected by the 
                                Secretary from manufacturers.
                            ``(ii) Scope.--The rulemaking--
                                    ``(I) shall not be limited to 
                                incandescent lamp technologies; and
                                    ``(II) shall include consideration 
                                of a minimum standard of 45 lumens per 
                                watt for general service lamps.
                            ``(iii) Amended standards.--If the 
                        Secretary determines that the standards in 
                        effect for general service lamps should be 
                        amended, the Secretary shall publish a final 
                        rule not later than January 1, 2017, with an 
                        effective date that is not earlier than 3 years 
                        after the date on which the final rule is 
                        published.
                            ``(iv) Phased-in effective dates.--The 
                        Secretary shall consider phased-in effective 
                        dates under this subparagraph after 
                        considering--
                                    ``(I) the impact of any amendment 
                                on manufacturers, retiring and 
                                repurposing existing equipment, 
                                stranded investments, labor contracts, 
                                workers, and raw materials; and
                                    ``(II) the time needed to work with 
                                retailers and lighting designers to 
                                revise sales and marketing strategies.
                            ``(v) Backstop requirement.--If the 
                        Secretary fails to complete a rulemaking in 
                        accordance with clauses (i) through (iv) or if 
                        the final rule does not produce savings that 
                        are greater than or equal to the savings from a 
                        minimum efficacy standard of 45 lumens per 
                        watt, effective beginning January 1, 2020, the 
                        Secretary shall prohibit the manufacture of any 
                        general service lamp that does not meet a 
                        minimum efficacy standard of 45 lumens per 
                        watt.
                            ``(vi) State preemption.--Neither section 
                        327 nor any other provision of law shall 
                        preclude California or Nevada from adopting, 
                        effective beginning on or after January 1, 
                        2018--
                                    ``(I) a final rule adopted by the 
                                Secretary in accordance with clauses 
                                (i) through (iv);
                                    ``(II) if a final rule described in 
                                subclause (I) has not been adopted, the 
                                backstop requirement under clause (v); 
                                or
                                    ``(III) in the case of California, 
                                if a final rule described in subclause 
                                (I) has not been adopted, any 
                                California regulations relating to 
                                these covered products adopted pursuant 
                                to State statute in effect as of the 
                                date of enactment of the Energy 
                                Independence and Security Act of 2007.
                    ``(B) Rulemaking before january 1, 2020.--
                            ``(i) In general.--Not later than January 
                        1, 2020, the Secretary shall initiate a 
                        rulemaking procedure to determine whether--
                                    ``(I) standards in effect for 
                                general service lamps should be 
                                amended; and
                                    ``(II) the exclusions for certain 
                                incandescent lamps should be maintained 
                                or discontinued based, in part, on 
                                excluded lamp sales data collected by 
                                the Secretary from manufacturers.
                            ``(ii) Scope.--The rulemaking shall not be 
                        limited to incandescent lamp technologies.
                            ``(iii) Amended standards.--If the 
                        Secretary determines that the standards in 
                        effect for general service lamps should be 
                        amended, the Secretary shall publish a final 
                        rule not later than January 1, 2022, with an 
                        effective date that is not earlier than 3 years 
                        after the date on which the final rule is 
                        published.
                            ``(iv) Phased-in effective dates.--The 
                        Secretary shall consider phased-in effective 
                        dates under this subparagraph after 
                        considering--
                                    ``(I) the impact of any amendment 
                                on manufacturers, retiring and 
                                repurposing existing equipment, 
                                stranded investments, labor contracts, 
                                workers, and raw materials; and
                                    ``(II) the time needed to work with 
                                retailers and lighting designers to 
                                revise sales and marketing strategies.
            ``(7) Federal actions.--
                    ``(A) Comments of secretary.--
                            ``(i) In general.--With respect to any lamp 
                        to which standards are applicable under this 
                        subsection or any lamp specified in section 
                        346, the Secretary shall inform any Federal 
                        entity proposing actions that would adversely 
                        impact the energy consumption or energy 
                        efficiency of the lamp of the energy 
                        conservation consequences of the action.
                            ``(ii) Consideration.--The Federal entity 
                        shall carefully consider the comments of the 
                        Secretary.
                    ``(B) Amendment of standards.--Notwithstanding 
                section 325(n)(1), the Secretary shall not be 
                prohibited from amending any standard, by rule, to 
                permit increased energy use or to decrease the minimum 
                required energy efficiency of any lamp to which 
                standards are applicable under this subsection if the 
                action is warranted as a result of other Federal action 
                (including restrictions on materials or processes) that 
                would have the effect of either increasing the energy 
                use or decreasing the energy efficiency of the product.
            ``(8) Compliance.--
                    ``(A) In general.--Not later than the date on which 
                standards established pursuant to this subsection 
                become effective, or, with respect to high-intensity 
                discharge lamps covered under section 346, the 
                effective date of standards established pursuant to 
                that section, each manufacturer of a product to which 
                the standards are applicable shall file with the 
                Secretary a laboratory report certifying compliance 
                with the applicable standard for each lamp type.
                    ``(B) Contents.--The report shall include the lumen 
                output and wattage consumption for each lamp type as an 
                average of measurements taken over the preceding 12-
                month period.
                    ``(C) Other lamp types.--With respect to lamp types 
                that are not manufactured during the 12-month period 
                preceding the date on which the standards become 
                effective, the report shall--
                            ``(i) be filed with the Secretary not later 
                        than the date that is 12 months after the date 
                        on which manufacturing is commenced; and
                            ``(ii) include the lumen output and wattage 
                        consumption for each such lamp type as an 
                        average of measurements taken during the 12-
                        month period.''.
            (11) Section 325(l)(4)(A) of the Energy Policy and 
        Conservation Act (42 U.S.C. 6295(l)(4)(A)) (as amended by 
        section 321(a)(3)(B) of the Energy Independence and Security 
        Act of 2007 (121 Stat. 1581)) is amended by striking ``only''.
            (12) Section 327(b)(1)(B) of the Energy Policy and 
        Conservation Act (42 U.S.C. 6297(b)(1)(B)) (as amended by 
        section 321(d)(3) of the Energy Independence and Security Act 
        of 2007 (121 Stat. 1585) and section 240(d)) is amended--
                    (A) in clause (i), by inserting ``and'' after the 
                semicolon at the end;
                    (B) in clause (ii), by striking ``; and'' and 
                inserting a period; and
                    (C) by striking clause (iii).
            (13) Section 321(30)(C)(ii) of the Energy Policy and 
        Conservation Act (42 U.S.C. 6291(30)(C)(ii)) (as amended by 
        section 322(a)(1)(B) of the Energy Independence and Security 
        Act of 2007 (121 Stat. 1587)) is amended by inserting a period 
        after ``40 watts or higher''.
            (14) Section 322(b) of the Energy Independence and Security 
        Act of 2007 (121 Stat. 1588) is amended by striking ``6995(i)'' 
        and inserting ``6295(i)''.
            (15) Section 327(c) of the Energy Policy and Conservation 
        Act (42 U.S.C. 6297(c)) (as amended by sections 324(f) of the 
        Energy Independence and Security Act of 2007 (121 Stat. 1594) 
        and section 6(e)(2)) is amended--
                    (A) in paragraph (6), by striking ``or'' after the 
                semicolon at the end;
                    (B) in paragraph (9)(B), by striking ``or'' at the 
                end;
                    (C) in paragraph (10), by striking the period at 
                the end and inserting a semicolon;
                    (D) by adding at the end the following:
            ``(11) is a regulation for general service lamps that 
        conforms with Federal standards and effective dates; or
            ``(12) is an energy efficiency standard for general service 
        lamps enacted into law by the State of Nevada prior to December 
        19, 2007, if the State has not adopted the Federal standards 
        and effective dates pursuant to subsection (b)(1)(B)(ii).''.
            (16) Section 325(b) of the Energy Independence and Security 
        Act of 2007 (121 Stat. 1596) is amended by striking ``6924(c)'' 
        and inserting ``6294(c)''.
            (17) This subsection and the amendments made by this 
        subsection take effect as if included in the Energy 
        Independence and Security Act of 2007 (Public Law 110-140; 121 
        Stat. 1492).
    (b) Energy Policy Act of 2005.--
            (1) Section 325(g)(8)(C)(ii) of the Energy Policy and 
        Conservation Act (42 U.S.C. 6295(g)(8)(C)(ii)) (as added by 
        section 135(c)(2)(B) of the Energy Policy Act of 2005) is 
        amended by striking ``20F'' and inserting ``-20F''.
            (2) This subsection and the amendment made by this 
        subsection take effect as if included in the Energy Policy Act 
        of 2005 (Public Law 109-58; 119 Stat. 594).
    (c) Energy Policy and Conservation Act.--Section 343(a) of the 
Energy Policy and Conservation Act (42 U.S.C. 6314(a)) is amended by 
striking ``Air-Conditioning and Refrigeration Institute'' each place it 
appears in paragraphs (4)(A) and (7) and inserting ``Air-Conditioning, 
Heating, and Refrigeration Institute''.
                                 <all>